032 - Performance - Answers
032 - Performance - Answers
Correct Answer – D
With equal runways length and slope characteristics and with all conditions
remaining the same (including take-off configuration – flap setting), the
limitation which may be affected is the obstacle limited take-off which is given
by the aircraft’s ability to climb, the height of the obstacle and its distance from
the beginning of the take-off run. All remaining limitations are dependant on
factors such as weight, runway length/slope, pressure altitude, temperature, etc.
which will remain the same in this case.
The reduced RTOM for RWY 20L is most likely a result of an obstacle at the end
of the runway.
Question N 2
Correct Answer – B
Refer to figure.
Considering this graph, first we can calculate the head/tailwind component to
be a full 4kt tailwind, as 050° is opposite to runway 23. Then given the outside
air temperature of +21°C, we have to choose the most limiting RTOM from 76.2
and 76.9 Tonnes (5kts of tailwind is obviously more limiting than still air), which
will be 76.2 Tonnes (76,200 kg), and therefore mean that we are in the box
which uses V1 = 144kt, VR = 144kt, V2 = 148kt.
We then have to take any extra factors into account; in this case, we can only
apply a negative factor for QNH pressures below 1013, so we apply no
correction for pressure (as our performance will be better than expected, which
we are not allowed to account for). We will have to account for the fact that our
air conditioning packs are on, which is an MTOM reduction of 850 kg.
76,200kg - 850kg = 75,350 kg
All other factors are specified in the graph, so do not need extra corrections.
Question N 3
Correct Answer – D
Refer to figure.
This graph requires a little examination to fully work out what information is
being given. For each temperature/wind combination, the table gives a
Maximum Take-Off Mass (MTOM), a limitation code, and the V 1 , V 2 and
V R speeds for that scenario.
For this question, it is the limitation code which must be understood, a
numerical system of noting what the primary limitations are that make the
MTOM and the V speeds those particular values. Sometimes there are 2
limitation codes, in the sense that two different parameters of the take off are
both limiting to that weight/V-speed combination.
In this case, both code 2 and 4 are limiting for the weight/V-speed combination,
and therefore the aircraft is limited by:
2) 2nd segment climb (still air gradient required for climb out after gear
retraction)
4) Obstacles (Obstacle clearance on the climb out)
Question N 4
Correct Answer – A
Refer to figure.
a) Enter the graph at aerodrome ambient temperature of +33ºC.
b) Move vertically to the aerodrome pressure altitude of 2 000 ft.
c) Travel horizontally left to the flap reference line and apply the appropriate
setting to read climb limit mass of approx. 57 900 kg.
d) Apply any corrections necessary:
“FOR PACKS OFF, INCREASE ALLOWABLE MASS BY 900 KG.”
To get the correct climb limited take-off mass, we should add 900 kg to 57 900
kg. However, the highest available option is 57 900 kg.
Question N 5
Correct Answer – D
Refer to figure.
This graph requires a little examination to fully work out what information is
being given. For each temperature/wind combination, the table gives a
Maximum Take-Off Mass (MTOM), a limitation code, and the V 1 , V 2 and
V R speeds for that scenario.
For this question, it is the limitation code which must be understood, a
numerical system of noting what the primary limitations are that make the
MTOM and the V speeds those particular values. Sometimes there are 2
limitation codes, in the sense that two different parameters of the take off are
both limiting to that weight/V-speed combination.
In this case, enter the table in the -10 kt tailwind column and look for the MTOM
of 67 500 kg. Read the limitation code of 4/4. The aircraft is limited by:
4) Obstacles (Obstacle clearance on the climb out)
Question N 6
Correct Answer – B
Refer to figure.
The graph does not provide any data for an altitude of 40 000 ft and weight at
engine failure of 35 000 lb. Therefore, we will need to interpolate.
Time taken:
Fuel used:
Distance travelled:
Question N 7
Correct Answer – C
Refer to figure.
From Figure 4.28 the Field Length-Limited Landing Mass can be determined. But
using the same figure in reverse you can find the Minimum Field Length
Required:
1. Use the dotted example depicted on the Figure 4.28 as a guide in reverse.
2. Enter with 54000 kg from the top right side.
3. Move horizontally to the left until 1000 ft Pressure altitude, halfway between
0 and 2 Pressure altitude line, of the first Pressure Altitude set of lines you meet
(Anti-skid: Inoperative).
4. Continue vertically down until the flaps reference line. No further correction,
because 40 o flaps position is exactly on the reference line.
5. Crossing the flaps reference line, continue further down until reaching at
"WET" .
6. Move parallel with the runway condition grid lines until the runway condition
reference line.
7. From that point continue vertically down until reaching at 10 kt headwind .
8. Move parallel with the wind grid lines until the wind reference line .
9. Finally, continue vertically down to get the Minimum Field Length Required
9125 ft.
Question N 8
Correct Answer – D
Refer to figure.
The Figure 4.31 provides advisory information to enable the operator to avoid
brake overheat problems. The chart enables due allowance to be made for a
single stop and, by using the graph as indicated, provides advice on the
procedure to be adopted and the minimum cooling time:
1. Enter the left vertical axis at the Landing mass 100 000 lb and travel
horizontally right to a speed of (V R E F - 3) kt corrected for wind component
minus 50% of a headwind: 138 kt - 3 kt - 5 kt = 130 kt.
2. From this intersection, drop vertically to the first reference line then
follow the gridlines to correct for Pressure Altitude 996 ft and OAT +25⁰C.
3. From this intersection continue vertically downward to the Braking
Configuration reference line.
4. Follow the grid-lines to the Auto Brake 3 with Normal Reverse #2 detent.
5. From the intersection continue vertically downward to read the Brake
Energy per Brake in millions of foot pounds, 9.5 million foot-pounds.
6. To this value, add one million foot pounds for each taxi mile to obtain the
total energy. Once an extra 4 million foot-pounds has been added for the
mile of expected taxiing, we are now at 13.5 million foot-pounds.
7. From the value of the total energy on continue vertically downward to
read the advised cooling schedule and recommend cooling time: Cooling
II required, 40 minutes ground cooling before take-off.
Question N 9
Correct Answer – A
Refer to figure.
If an engine fails in the cruise, the remaining engine(s) are set to maximum
continuous thrust, in an attempt to maintain height. At cruise altitudes, the
attempt to maintain height usually fails, because of inadequate thrust on the
remaining engine(s) and the aircraft will descend down to a height at which it is
able to stabilise. This is called "driftdown".
This is a quite straightforward graph, which helps to find the maximum one-
engine inoperative net level-off height for different temperature conditions and
configurations:
1. Enter with the expected gross mass 66 000 kg and draw a vertical line
upwards, until intersecting the ISA+15ºC dotted curve (dotted curves are for
LRC, while bold lines for Green Dot speeds.
2. Continue horizontally to the left and read the net level-off height FL 190.
3. Correct for Engine Anti-Ice-ON at ISA+15ºC: 19 000 ft - 1 200 ft = 17 800 ft.
Question N 10
Correct Answer – C
Refer to figure.
a) Enter the graph at aerodrome ambient temperature of +30ºC.
b) Move vertically to the aerodrome pressure altitude of 2 000 ft.
c) Travel horizontally left to the flap reference line and apply the appropriate
setting to read climb limit mass of approx. 54 800 kg.
d) Apply any corrections necessary:
“FOR PACKS OFF, INCREASE ALLOWABLE MASS BY 900 KG.”
54 800 kg + 900 kg = 55 700 kg
The closest option is 55 500 kg.
Question N 11
Correct Answer – A
Refer to figure.
A Regulated Take-Off Weight (RTOW) table is a simplified form of table to use
and is produced for a specific aircraft type on a particular runway and shows
MTOM and speeds for a variety of temperatures and pressure altitudes,
sometimes giving different configuration options.
First of all, the wind direction 050 o is exactly parallel to the runway 23L,
so the wind speed of 4 kt is a tailwind.
The questions asks to take the most conservative data and not
interpolate, so, enter the RTOW table from the "- 5 kt" column.
In each box, the Maximum Take-off Mass is at top left. Move vertically
down through the "- 5 kt" column, until you reach at MTOM just over the
Actual TOM given, 72 820 kg.
We find this at 73.4 tonnes, which corresponds to an OAT of 41°C.
In the same box, the numbers "40-40-44" correspond to the
speeds: V 1 (140 kt), V R (140 kt) and V 2 (144 kt), accordingly.
Apply the correction -2°C to the TFLEX, due to the wet runway
condition: TFLEX = 41°C - 2°C = 39°C.
Apply the correction: -6, -3, -2 to the above speeds, due to the wet runway
condition: V 1 = 140 - 6 = 134 kt, V R = 140 - 3 = 137 kt, V 2 = 144 - 2 = 142 kt.
No corrections are required for QNH higher than 1013 hPa.
Question N 12
Correct Answer – D
Refer to figure.
To calculate the V take-off speeds use the given graph and tables in the
following manner:
Question N 16
Correct Answer – A
Refer to figure.
The Climb Limited Landing Mass ensures that the minimum permissible gradient
is obtained and should be corrected in accordance with the statements beneath
the graph, if necessary:
Question N 19
Correct Answer – D
Refer to figure.
This graphs is provided for Flaps psoition 5° and is a rapid means of obtaining
the value of obstacle clearance after take-off. It is intended for use when a
detailed airport analysis is not available. Detailed analysis for the specific case
from the aeroplane flight manual may result in a less restrictive weight and can
account for the non-use of the air conditioning packs:
1. Enter the bottom left vertical axis at the obstacle height 360 ft.
2. Travel horizontally right to intersect the obstacle distance from the break
release point 21 000 ft.
3. From this intersection, move vertically up to the ambient temperature
reference line, then parallel to the grid lines until OAT +15⁰C.
4. Continue vertically directly to the wind component reference line and then
parallel to the grid lines from this point to the value of the wind
component 10 kt headwind.
5. Finally, continue vertically to read the Obstacle Limited Take-off Mass 58
900 kg.
Regulated take-off mass (RTOM) is the most restrictive between the Field
Length Limit, Climb Limit, Obstacle Limit, Tyre Speed Limit and the Maximum
Structural Limit. Thus, the RTOM is 58 900 kg.
Question N 20
Correct Answer – B
Refer to figure.
The Figure 4.31 provides advisory information to enable the operator to avoid
brake overheat problems. The chart enables due allowance to be made for a
single stop and, by using the graph as indicated, provides advice on the
procedure to be adopted and the minimum cooling time:
1. Enter the left vertical axis at the Landing mass 100 000 lb and travel
horizontally right to a speed of (V R E F - 3) kt corrected for wind component
minus 50% of a headwind: 138 kt - 3 kt - 25 kt = 110 kt.
2. From this intersection, drop vertically to the first reference line then
follow the gridlines to correct for Pressure Altitude 984 ft and OAT +25⁰C.
3. From this intersection continue vertically downward to the Braking
Configuration reference line.
4. Follow the grid-lines to the Auto Brake 2 with Normal Reverse #2 detent.
5. From the intersection continue vertically downward to read the Brake
Energy per Brake in millions of foot pounds, 6.1 million foot-pounds.
6. To this value, add one million foot pounds for each taxi mile to obtain the
total energy. Once an extra 4 million foot-pounds has been added for the
mile of expected taxiing, we are now at 10.1 million foot-pounds.
7. From the value of the total energy on continue vertically downward to
read the advised cooling schedule and recommend cooling time: Cooling
II required, 18 minutes ground cooling before take-off.
Question N 21
Correct Answer – A
Refer to figure.
This graphs is provided for Flaps position 5° and is a rapid means of obtaining
the value of obstacle clearance after take-off. It is intended for use when a
detailed airport analysis is not available. Detailed analysis for the specific case
from the aeroplane flight manual may result in a less restrictive weight and can
account for the non-use of the air conditioning packs:
1. Enter the bottom left vertical axis at the obstacle height 360 ft.
2. Travel horizontally right to intersect the obstacle distance from the break
release point 18 000 ft.
3. From this intersection, move vertically up to the ambient temperature
reference line, then parallel to the grid lines until OAT +25⁰C.
4. Continue vertically to the pressure altitude reference line and then parallel
to the grid lines from this point to the value of the pressure altitude 1 000
ft.
5. Continue vertically to the wind component reference line and then parallel
to the grid lines from this point to the value of the wind component 10 kt
headwind.
6. Finally, continue vertically to read the Obstacle Limited Take-off Mass 54
200 kg.
Performance-Limited Take-off Mass (PLTOM) is the most restrictive between
the Field Length Limit (60 000 kg), Climb Limit (50000 kg), Obstacle Limit (54
200 kg) and Tyre Speed Limit (70 000 kg). Thus, the PLTOM is 50 000 kg.
Question N 22
Correct Answer – C
Refer to figure.
The figure shows the brake cooling times with or without brake cooling fan, for a
given brake energy and ambient temperature:
According to the table's instructions above the table: "If the energy and
the OAT are not given in the table, use the values given in the next column
right/row below". The Brake Energy 44 MJ is not given in the table, so
enter with the next row below, 45 MJ.
Move to the right until the intersection box with the OAT 0°C.
Each box gives two cooling times in minutes. Use the upper one, 140
minutes, which refers to a cooling time with brake cooling fan
unavailable.
Question N 23
Correct Answer – A
Refer to figure.
A Regulated Take-Off Weight (RTOW) table is a simplified form of table to use
and is produced for a specific aircraft type on a particular runway and shows
MTOM and speeds for a variety of temperatures and pressure altitudes,
sometimes giving different configuration options.
First of all, the wind direction 050 o is exactly in line with the runway 23L,
so the wind speed of 6 kt is a tailwind.
The question asks to take the more conservative data points and not
interpolate, so enter the RTOW chart from the "-10 kt column".
In each box, the Maximum Take-off Mass is at the top left. Move vertically
down the "-10 kt column", until you reach at MTOM just over the Actual
TOM given, 67050 kg.
We find this at 67.1 tonnes, which corresponds to an OAT of 63°C and is
equal to the Assumed/FLEX T° given.
In the same box, the numbers "29-29-33" correspond to the
speeds: V 1 (129 kt), V R (129 kt) and V 2 (133 kt), accordingly.
QNH is 1003 hPa, so apply the corrections: 0, 0, +1 to the above speeds
for "QNH 1013 -10 hPa".
Additionally, apply the corrections: -6, -3, -2 to the above speeds for Wet
runway.
No corrections are required for Engine anti-ice and Packs.
Finally, after applying the required corrections, the speeds for a "reduced
thrust take-off" on the 23L dry runway will be:
1. V 1 = 129 - 6 = 123 kt
2. V R = 129 - 3 = 126 kt
3. V 2 = 133 + 1 - 2 = 132 kt
Question N 24
Correct Answer – B
Landing performance calculation.
A commercial turbojet aeroplane must be able to land within 60% of the Landing
Distance Available (LDA).
LDA = 3000 m
60% of LDA = 3000 x 0.6 = 1800 m
The runway being wet must also be factored by 1.15.
1800 m / 1.15 = 1565 m
Question N 25
Correct Answer – D
Climb gradient is the ratio of height gained to distance travelled => tangent to
climb angle “y”.
Sin y = (T – D) / W
Sin y = (T/W) – (D/W)
Sin y = T / (m x g) – (D / (L/cos y))
Sin y = T / (m x g) – (D x cos y)/L
Sin y = T / (m x g) – D/L
Climb gradient = (T / (m x g) – D/L) x 100
With regards to this question, Climb gradient = (236000 / (76000 x 10) – 1/8) x
100 = 18.5%
Question N 26
Correct Answer – C
Refer to figure.
Using the graph as shown above, with special mention of the "Brakes on speed
at landing" being our VREF corrected for the 4kt headwind and the correction
factor in the question from a VREF of 125 kt to a brakes-on speed of 120kt. The
final output figure of the graph is 6.9 million foot-pounds of energy per brake.
Once an extra 1 million foot-pounds has been added for the mile of expected
taxiing, we are now at 7.9 million foot-pounds, which is just within region I, in
which no special cooling procedure is required.
Question N 27
Correct Answer – A
Refer to figure.
The graph at Figure 4.31 provides advisory information to enable the operator to
avoid brake overheat problems. The question refers to an "Abandoned Take-off",
so follow the steps given in paragraph 5.3.1.1, page 49:
Enter the top left vertical axis at the Regulated Take-Off Mass, 57 500
kg and travel horizontally right to the speed when rejection
commenced, 100 kt.
From this intersection, drop vertically to the first reference line, then
follow the gridlines to correct for Pressure Altitude, 1 400 ft and OAT, -
10°C.
From this intersection continue vertically downward to read the
recommended cooling time, approximately 55 minutes.
Ιf some credit is given for using reverse thrust, it cannot be taken into account
for "Abandoned Take-offs" according to CAP 698 paragraph 5.3.1.1, page 49.
However, in reality, any reverse thrust application, as an auxialiary means of
braking, will decrease the cooling time.
NOTE: Allowances for reverse thrust and braking configurations only apply for the
landings, not the Abandoned Take-offs.
Question N 28
Correct Answer – B
Refer to figure.
Remember that in the worst case scenario, V MB E is equal to V 1 . In this case, we
are given a V 1 of 148 kt.
(1) Correct V MBE for slope and wind. The corrections can be found under the
graph:
Since we are working backwards, the above corrections will be added (not
subtracted).
V M BE = 148 kt + 2 kt + 20 kt = 170 kt
(2) Enter the graph on the left hand side at a pressure altitude of 1 487 ft. Track
horizontally to the right until you intersect an OAT of +19ºC. Continue vertically
down.
(3) Enter the graph on the right-hand-side at the bottom, at a VMBE of 170 kt.
Track horizontally to the left until you intersect your first line. Read a result
of approximately 64 000 kg.
Question N 29
Correct Answer – A
Refer to figure.
The Quick Turnaround limit is related to the wheel fusible alloy plugs that are
designed to melt at a predetermined temperature to prevent the tyre exploding
when it's been subjected to high temperatures caused by heavy braking. After a
brake application, the energy which the brake has absorbed is released as heat
and until this heat is dissipated, the amount of additional energy which the
brake can absorb without failure is reduced. Therefore, take-off planning must
consider the effects of residual brake energy (or brake temperature) if the
previous landing involved significant braking and/or the airplane turnaround is
relatively short or the Maximum Quick Turnaround Mass has been exceeded.
Question N 30
Correct Answer – A
Refer to figure.
Remember that in the worst case scenario, V MB E is equal to V 1 . In this case, we
are given a V 1 of 145 kt.
(1) Correct V MBE for slope and wind. The corrections can be found under the
graph:
"DECREASE VMBE by 5 kt FOR 1% DOWNHILL RUNWAY SLOPE"
"DECREASE VMBE by 20 kt FOR 10 kt TAILWIND"
Since we are working backwards, the above corrections will be added (not
subtracted).
Slope: 0.2% down => Correction: + 1 kt
Tailwind: 5 kt => Correction: + 10 kt
V M BE = 145 kt + 1 kt + 10 kt = 156 kt
(2) Enter the graph on the left hand side at a pressure altitude of 1 998 ft. Track
horizontally to the right until you intersect an OAT of +38ºC. Continue vertically
down.
(3) Enter the graph on the right-hand-side at the bottom, at a V MB E of 156 kt.
Track horizontally to the left until you intersect your first line. Read a result
of approximately 68 000 kg.
Question N 31
Correct Answer – B
Refer to figure.
Considering this graph, first we can calculate the head/tailwind component to
be 0kts, as 140° is perpendicular to runway 23, so it is a full crosswind. Then
given the outside air temperature of +10°C, we have to choose the most limiting
RTOM from 78.0 and 78.7 Tonnes, which will be 78.0 Tonnes (78,000kg), and
therefore mean that we are in the box which uses V1 = 147kt, VR = 147kt, V2 =
151kt.
We then have to take any extra factors into account; in this case, we can apply a
factor for QNH pressures below 1013, and we are 5hPa below it at 1008hPa, but
we are not allowed to interpolate, so we have to apply a full 80kg reduction for
pressure. We will have to account for the fact that our engine anti-ice is on,
which is an MTOM reduction of 380kg. We then have to account for the wet
runway also, which is a reduction of 430 kg.
78,000 - 80 - 380 - 430 = 77,110kg
Question N 32
Correct Answer – D
Refer to figure.
The Quick Turnaround limit is related to the wheel fusible alloy plugs that are
designed to melt at a predetermined temperature to prevent the tyre exploding
when its been subjected to high temperatures caused by heavy braking. After a
brake application, the energy which the brake has absorbed is released as heat
and until this heat is dissipated, the amount of additional energy which the
brake can absorb without failure is reduced.
Take a look at the attached figure taken from CAP 698 - you can clearly see that
the Maximum Permissible Landing Mass for a Quick Turnaround is limited by the
Aerodrome Pressure Altitude, Airport OAT, Flaps setting, Runway Slope and
Wind.
The higher the pressure altitude and the temperature, the lower the
density. As a result, the aircraft produces less lift and thrust for a given
speed and power setting. Therefore, the aircraft must fly a higher
approach speed, leading to higher TAS and consequently higher
groundspeeds on landing => higher brake temperatures due to heavier
braking required.
Question N 33
Correct Answer – D
The maximum performance limited landing mass (MPLLM) is the landing mass
limited by departure airfield considerations such as runway length, obstacles,
temperature and altitude.
For this question, the MPLLM is the lowest between the Approach climb limit
mass, Landing climb limit mass and Field length limit mass given. Thus, the
MPLLM is 32 250 lb.
The maximum performance limited landing mass compared with the maximum
structural landing mass (the lower of the two) gives the Regulated Landing
Mass.
NOTE: The question asks for the maximum performance limited landing mass.
Question N 34
Correct Answer – D
Refer to figure.
Abandoned Take-Off
a) Enter the top left vertical axis at the Regulated Take-Off Mass (100 000 lb)
and travel horizontally right to V1 minus 50% of headwind or plus 150% of
tailwind (138 kt - 5 kt = 133 kt).
b) From this intersection, drop vertically to the first reference line then follow
the gridlines to correct for Pressure Altitude (1 000 ft) and OAT (25ºC).
c) From this intersection continue vertically downward to read the Brake Energy
per Brake in millions of foot pounds.
d) To this value add one million foot pounds for each taxi mile to obtain the total
energy.
e) From the value of the total energy continue vertically downward to determine
the advised cooling schedule and recommended cooling time.
Enter from the Aircraft corrected cruise mass, due to the "ENG ANTI-ICE
ON": 43 000 kg + 1 950 kg = 44 950 kg.
Move vertically upwards until crossing the "ISA +10ºC or
below" temperature line.
Continue horizontally to the left and read the Level-off Pressure
Altitude: 22 200 ft.
Thus, the most appropriate diversion airports, in case of an engine failure during
the cruise phase, are Airport 1 and Airport 4, for which the required airport
clearances (21 000 ft & 19 500 ft) are lower than the Level-off Pressure Altitude,
22 200 ft.
Question N 40
Correct Answer – B
Refer to figure.
(1) Enter the graph at the left side at a pressure altitude of 16 000 ft. Track
horizontally to the right until you intersect the “+10ºC & BELOW”.
(2) Continue your line vertically down and read off a gross mass of
approximately 56 600 kg.
(3) Apply the correction for A/C AUTO (HIGH): - 2500 kg.
First of all, the wind direction 230 o is exactly opposite to the runway 23L,
so the wind speed of 5 kt is a headwind.
The questions asks to take the most conservative data and not
interpolate, so, enter the RTOW table from the "0 kt" column.
The OAT is +12°C, for which there is no exact row, it is between +5°C and
+15°C. The more conservative row is the higher temperature of +15°C.
The intersection between the "0 kt" column and "+15°C" row gives a RTOW
of 78 000 kg.
Applying the correction "-430 kg" for the wet runway condition, due to the
moderate rain, the RTOW for departure becomes: 78 000 kg - 430 kg = 77
570 kg.
No correction for pressures greater than 1013hPa is required.
Question N 43
Correct Answer – D
The Field Length Limited Take-off Mass (FLLTOM) is likely to be the most
restrictive mass when operating from short runways in environmental conditions
allowing good climb performance – low field elevation, high pressure and low
temperature. It can be increased by selecting the highest specified take-off flap
setting that still complies with other limits and by performing a packs-off take-
off.
Question N 44
Correct Answer – A
Refer to figure.
A Regulated Take-Off Weight (RTOW) table is a simplified form of table to use
and is produced for a specific aircraft type on a particular runway and shows
MTOM and speeds for a variety of temperatures and pressure altitudes,
sometimes giving different configuration options.
First of all, the wind direction 230 o is exactly opposite to the runway 23L,
so the wind speed of 16 kt is a headwind.
The questions asks to take the most conservative data and not
interpolate, so, enter the RTOW table from the "+ 10 kt" column.
In each box, the Maximum Take-off Mass is at top left. Move vertically
down through the "+10 kt" column, until you reach at MTOM just over the
Actual TOM given, 71 840 kg.
We find this at 72.1 tonnes, which corresponds to an OAT of 57°C.
In the same box, the numbers "39-39-44" correspond to the
speeds: V 1 (139 kt), V R (139 kt) and V 2 (144 kt), accordingly.
No correction is required for the TFLEX.
Apply the correction: +1 kt only to the V 2 speeds, due to QNH -5 hPa.
Since we are working backwards, the above corrections will be subtracted (not
added).
V M BE = 149 kt - 1 kt + -3 kt = 145 kt
(2) Enter the graph on the left hand side at a pressure altitude of 1 487 ft. Track
horizontally to the right until you intersect an OAT of +19ºC. Continue vertically
down.
(3) Enter the graph on the right hand side at the bottom, at a V MB E of 145 kt.
Track horizontally to the left until you intersect your first line. The result is in
excess of 68 000 kg.
Note: V 1 exceeds V MBE , therefore a correction should be applied. However, it is not
easy for us to determine the exact brake release weight, and whatever correction
we need to make, the final result will still be "in excess of 68 000kg".
Question N 46
Correct Answer – B
Refer to figures.
To calculate the V speeds use the given graph and table in the following
manner:
1. Initially, enter the density sub-graph with pressure altitude (1 500 ft) and
ambient temperature (+25°C) to determine which of the columns of the
table should be used.
2. The intersection in the density sub-graph shows "B" column, so use
the "B" column of the V speed table.
3. Enter the V speed tables at the actual take-off mass (60 000 kg) and
extract V 1 : 145 kt, V R : 148 kt, and V 2 : 155 kt.
4. Correct only V 1 for slope (-1%) and for wind component (-5 kt) by entering
the table at the top of the table, as appropriate, at the actual take-off
mass and interpolate the correction necessary.
5. Apply the corrections to V 1 : 145 kt - 1(for downslope) -1(for tailwind)= 143
kt.
Thus, the take-off speeds are V 1 =143 kt, V R =148 kt, V 2 =155 kt.
Question N 47
Correct Answer – B
Refer to figure.
A Regulated Take-Off Weight (RTOW) table is a simplified form of table to use
and is produced for a specific aircraft type on a particular runway and shows
MTOM and speeds for a variety of temperatures and pressure altitudes,
sometimes giving different configuration options.
We are taking off from runway 26R (Magnetic direction 260º) with a full
headwind of 13 kt.
Correction for 13 kt: 5 200 kg
Question N 52
Correct Answer – A
Refer to figure.
A Regulated Take-Off Weight (RTOW) table is a simplified form of table to use
and is produced for a specific aircraft type on a particular runway and shows
MTOM and speeds for a variety of temperatures and pressure altitudes,
sometimes giving different configuration options.
First of all, the wind direction 230 o is exactly opposite to the runway 23L,
so the wind speed of 10 kt is a headwind.
So, enter the RTOW table from the "+10 kt" column.
In each box, the Maximum Take-off Mass is at top left. Move vertically
down through the +10 kt column, until you reach at MTOM just over the
Actual TOM given, 71180 kg.
We find this at 71.3 tonnes, which corresponds to an OAT of 61°C and is
equal to the Assumed/FLEX T° given.
In the same box, the numbers "38-38-43" correspond to the
speeds: V 1 (138 kt), V R (138 kt) and V 2 (143 kt), accordingly.
Apply the correction: -2, -1, -1 to the above speeds for Packs - ON.
Additionally, apply the correction: -1, -1, -2 to the above speeds for Engine
Anti-ice - ON.
No corrections are required for QNH higher than 1013 hPa.
Finally, after applying the required corrections, the speeds for a reduced
thrust take-off on the 23L dry runway will be:
1. V 1 = 138 - 2 - 1 = 135 kt
2. V R = 138 - 1 - 1 = 136 kt
3. V 2 = 143 - 1 - 2 = 140 kt
Question N 53
Correct Answer – C
Refer to figure.
The graph at Figure 4.5 guarantees attainment of the most severe gradient
requirement of the net flight path. It does not guarantee obstacle clearance.
Method of Use:
Question N° 54
Correct Answer – C
A dry (maximum) V 1 is the normal decision speed that following an engine
failure allows the take-off to be continued safely within the TODA or to be
stopped safely within the ASDA. A wet (minimum) V 1 is the maximum speed for
abandoning a take-off on a contaminated runway. A wet V 1 improves the
stopping capabilities (final stop point) back to the dry conditions level but
degrades the takeoff chances with a reduced screen height in the event of a
take-off being continued. A recommended wet V 1 for contaminated conditions is
the dry V 1 - 10 knots. Thus wet V 1 is a lower speed than dry V 1 .
Note: Due to lower friction and consequently reduced braking action on a wet
runway, longer braking distances are experienced, V 1 must be decreased.
Question N° 55
Correct Answer – C
Refer to figure.
Drag curves are normally drawn plotted against EAS. In case TAS is used
instead of EAS, the graph moves left and right as TAS respectively decreases
and increases for a given EAS.
There are some useful diagrams, called "ECTM diagrams", that help to remember
the relationship between EAS, CAS, TAS and Mach number in climbs and
descents.
For a normal atmosphere, the sequence left to right is always drawn as ECTM.
Draw the parameter that is to be held constant as a vertical line, draw
connecting lines to the remaining letters.
The figure shows ECTM diagrams for a constant Mach number climb or descent,
then a constant TAS climb or descent, then for a constant CAS.
If climbing use -ECTM+, which means that, if one of the speeds is kept constant,
then the speeds to the right are increasing and to the left decreasing.
Conversely, if descending use +ECTM-.
For this question, the density altitude is decreasing, this means the air is
becoming more dense, thus, using also the ECTM method, the TAS for a given
EAS is decreasing.
The graph which shows a decrease in TAS, with the drag curve moving
horizontally left, is Figure 2.
Question N° 56
Correct Answer – A
Refer to figure.
If an engine fails in the cruise, the remaining engine(s) are set to maximum
continuous thrust, in an attempt to maintain height. At cruise altitudes, the
attempt to maintain height usually fails, because of inadequate thrust on the
remaining engine(s) and the aircraft will descend down to a height at which it is
able to stabilise. This is called "driftdown".
This is a quite straightforward graph, which helps to find the maximum one-
engine inoperative net level-off height for different temperature conditions and
configurations:
1. Enter with the expected gross mass 66 000 kg and draw a vertical line
upwards, until intersecting the ISA+15ºC dotted curve (dotted curves are for
LRC, while bold lines for Green Dot speeds.
2. Continue horizontally to the left and read the net level-off height FL 190.
3. Correct for Engine Anti-Ice-ON at ISA+15ºC: 19 000 ft - 1 200 ft = 17 800 ft.
Question N° 57
Correct Answer – C
Descent at a Constant Mach Number in Standard Conditions
During a descent, LSS will be increasing, as temperature increases. Therefore, if
Mach number is being kept constant the TAS must be increasing (Mach number
= TAS/LSS). During the descent air density increases TAS is increasing and CAS
also increases at a greater rate (Dynamic Pressure = 1⁄2 ρ V 2 ). Similarly, in a
climb at constant Mach number the TAS or CAS both reduce.
Question N° 58
Correct Answer – C
Concerning Class B take-off obstacle clearance regulations for multi-engined
aeroplanes, CAT.POL.A.310 (a) refers that:
The take-off flight path of aeroplanes with two or more engines shall be
determined in such a way that the aeroplane clears all obstacles by a
vertical distance of at least 50 ft, or by a horizontal distance of at least 90
m plus 0,125 × D, where D is the horizontal distance travelled by the
aeroplane from the end of the TODA or the end of the take-off distance if
a turn is scheduled before the end of the TODA, except as provided in (b)
and (c). For aeroplanes with a wingspan of less than 60 m, a horizontal
obstacle clearance of half the aeroplane wingspan plus 60 m plus 0,125
× D may be used. Assuming that this is the distance laterally from the
line-of-flight to the edge of the accountability area it is the semi-width, or
half-width, of the total accountability area.
Question N° 59
Correct Answer – D
V M CG is defined as "the minimum CAS on the take-off run at which, on failure of the
critical engine and with the remaining engine(s) at maximum take-off power, the
pilot can retain control of the aircraft using the primary aerodynamic controls
alone."
After an engine failure during take-off, if the decision is made to continue the
take-off, then the assymetric thrust will force the aircraft off the runway centre
line. The pilot will try to keep the aircraft straight with rudder application,
producing an aerodynamic force.
The rudder effectiveness increases with forward speed. Below the minimum
control speed on the ground, V MC G , the aircraft cannot be kept straight.
V E F (engine failure speed), therefore, must be greater than or equal to V MC G and as
V 1 is greater than V E F , it follows that V 1 must be greater than V M C G .
If V 1 is less than V M CG , then the aircraft will not be able to be kept straight on the
runway, if a "go" decision is made.
If a range of decision speeds exists, that encompasses the V MC G as the highest
speed which can be chosen to satisfy the requirement. If not, the TOM must be
reduced until the range of speeds just encompasses V MC G and then V 1 is set equal
to V M C G . This creates a V M C G limited take-off mass.
In most cases V MC G intrudes only on to the lowest decision speeds of a range. If
this is the case, the speeds in the range below V M CG cannot be used.
V M CG is most likely to be limiting where the assymetric thrust is greatest:
Question N° 60
Correct Answer – A
Refer to figures.
ICAO Annex 14
Volume 1
Declared distances.
a) Take-off run available (TORA). The length of runway declared available and
suitable for the ground run of an aeroplane taking off.
b) Take-off distance available (TODA). The length of the take-off run
available plus the length of the clearway, if provided.
c) Accelerate-stop distance available (ASDA). The length of the take-off run
available plus the length of the stopway, if provided.
d) Landing distance available (LDA). The length of runway which is declared
available and suitable for the ground run of an aeroplane landing.
SUMMARY:
TORA = Take-off run available
TODA = TORA + CWY (Clearway)
ASDA = TORA + STW (Stopway)
LDA = TORA - Displaced threshold
Question N° 61
Correct Answer – A
Specific Fuel Consumption (SFC) is the amount of fuel used per unit of thrust
(for jets) and unit of power (for props) in one unit of time. SFC varies with the
ambient conditions. SFC is best at a minimum and one of the factors it is
dependent upon include:
Temperature. In cold air, at a particular altitude, the RPM may be reduced to
provide the power required because:
(a) The power available from the engine is greater.
(b) The power required to propel the airframe in cold air is less.
The colder the temperature, therefore, the lower will be the SFC because the
power absorbed (wasted) at the lower temperature is reduced and the thermal
efficiency is increased.
Question N° 62
Correct Answer – B
SPECIFIC RANGE
There are two types of specific range, specific air range (SAR) and specific
ground range (SGR).
Specific air range is the range through the air, while SGR is the ground range.
The difference is due to wind strength and direction. When wind is to be
considered, specific range is assumed to mean SGR.
Specific range is the distance flown per unit of fuel. Using the aviation units
nautical miles and kilograms:
Specific Range = nm / kg
Dividing by time;
Specific Range = TAS / Fuel Flow
Question N° 63
Correct Answer – D
Refer to figure.
Power required is the power needed at any given speed to overcome the
particular amount of drag that exists at that speed.
It is important to note for this next section that the shape of the thrust required
/ available graphs are based on IAS initially, but are converted to TAS to be more
useful with Power Required / Power Available, which are created from the thrust
graphs using TAS via the formulas above.
In this question, then, we are descending, so we are expecting our Power
Required to decrease, and our TAS for each point on the graph to decrease also,
so the Power Required vs. TAS graph will move down and to the left.
Also, the Power Available will increase as we descend into denser air, and
the TAS will also decrease for every point on the graph, the same as before, to
make the Power Available vs TAS graph move up and to the left.
The annex above shows what happens to the curves when the
aircraft descends (as in this question).
Question N° 64
Correct Answer – A
Refer to figure.
The Maximum Performance-Limited TOM, which ensures compliance with the
applicable operational requirements for a Commercial Air Transport operation is
the higher of the lowest mass limits for each Flap/Slat position setting:
The lowest (most limiting) mass for Flap/Slat position setting 1 is: 17 000
kg.
The lowest (most limiting) mass for Flap/Slat position setting 2 is: 16 800
kg.
Thus, the Maximum Performance-Limited TOM is the higher of the two, 17 000
kg, which means that if you take-off with Flap/Slat position setting 1 the MTOM
will be 200 kg greater than that with Flap/Slat position setting 2, so the optimum
Flap/Slat position setting is 1.
Question N° 65
Correct Answer – C
Class A Gross Gradients
1º Segment 2º Segment 3º Segment 4º Segment
Gradient for
2 Engines > 0% > 2.4% > 1.2% > 1.2%
Gradient for
3 Engines > 0.3% > 2.7% > 1.5% > 1.5%
Gradient for
4 Engines > 0.5% > 3.0% > 1.7% > 1.7%
Note: While third segment is usually flown in level flight, the available gradient
must be at least equal to that required in final segment (1.2%). During third
segment the high lift devices are retracted.
EU-OPS states that the climb gradient to use for the purpose of calculating
obstacle clearance must be the net climb gradient. Net gradient is the gross
gradient reduced by a safety factor:
Solution:
Minimum climb gradient is 2%. The turning requires an additional increment of
0.5%, addition of 0.8% for the net to gross conversion.
2% + 0.5% + 0.8% = 3.3 %
Question N° 66
Correct Answer – C
Take-off with Increased V 2 Speed
This procedure is used when the performance limited mass is the climb limit
mass. At V 2 the climbing performance is poor and limits the maximum take-off
mass. It is important to understand that in the event of engine failure, the initial
climb out speed is V 2 . However, V 2 is not the best climb angle speed. V 2 is
considerably slower than the best angle of climb speed, which is V X . Climbing
with a speed closer to the best angle of climb greatly enhance the climb
performance.
If runway available it would be possible to stay on the runway for longer during
the take-off to build up more speed to a higher V 1 , this will ensure that at the
screen height, a faster V 2 will be reached, closer to V X . As a result of the
improved climb performance, the climb limit mass can be increased.
Question N° 67
Correct Answer – B
In an emergency descent, for instance a descent initiated by the pilot following
depressurization, the aim is to reach FL100 as soon as possible.
To achieve this requirement, the airplane would need to lose height with the
maximum possible rate of descent.
ROD (ft/m) = G/S x Gradient of Descend
To maximize the ROD, the airspeed should be maximize within the operational
limits of the aircraft.
At cruising altitude an airliner will be flying Mach no. so the operational limit is
the MMO (Maximum Operating Mach Number).
If airbrakes in use, the gradient of descend increases, consequently the ROD
increases as well.
Question N° 68
Correct Answer – A
Refer to figure.
A Regulated Take-Off Weight (RTOW) table is a simplified form of table to use
and is produced for a specific aircraft type on a particular runway and shows
MTOM and speeds for a variety of temperatures and pressure altitudes,
sometimes giving different configuration options.
First of all, the wind direction 230 o is exactly opposite to the runway 23L,
so the wind speed of 10 kt is a headwind.
So, enter the RTOW table from the "+10 kt" column.
In each box, the Maximum Take-off Mass is at top left. Move vertically
down through the +10 kt column, until you reach at MTOM just over the
Actual TOM given, 71180 kg.
We find this at 71.3 tonnes, which corresponds to an OAT of 61°C and is
equal to the Assumed/FLEX T° given.
In the same box, the numbers "38-38-43" correspond to the
speeds: V 1 (138 kt), V R (138 kt) and V 2 (143 kt), accordingly.
Apply the correction: -2, -1, -1 to the above speeds for Packs - ON.
Additionally, apply the correction: -1, -1, -2 to the above speeds for Engine
Anti-ice - ON.
No corrections are required for QNH higher than 1013 hPa.
Finally, after applying the required corrections, the speeds for a reduced
thrust take-off on the 23L dry runway will be:
1. V 1 = 138 - 2 - 1 = 135 kt
2. V R = 138 - 1 - 1 = 136 kt
3. V 2 = 143 - 1 - 2 = 140 kt
Question N° 69
Correct Answer – C
Screen Height is the height of an imaginary screen which the aeroplane would
just clear when taking off or landing in an unbanked attitude with landing gear
extended.
Question N° 70
Correct Answer – B
Refer to figures.
To calculate the V speeds use the given graph and table in the following
manner:
1. Initially, enter the density sub-graph with pressure altitude (1 500 ft) and
ambient temperature (+25°C) to determine which of the columns of the
table should be used.
2. The intersection in the density sub-graph shows "B" column, so use
the "B" column of the V speed table.
3. Enter the V speed tables at the actual take-off mass (60 000 kg) and
extract V 1 : 145 kt, V R : 148 kt, and V 2 : 155 kt.
4. Correct only V 1 for slope (-1%) and for wind component (-5 kt) by entering
the table at the top of the table, as appropriate, at the actual take-off
mass and interpolate the correction necessary.
5. Apply the corrections to V 1 : 145 kt - 1(for downslope) -1(for tailwind)= 143
kt.
Thus, the take-off speeds are V 1 =143 kt, V R =148 kt, V 2 =155 kt.
Question N° 71
Correct Answer – C
Specific Range (SR) is a measure of range capability expressed as the air
distance (NAM) travelled per unit of fuel consumed or as TAS divided by fuel
flow. A high Specific Range equals a good range capability.
A heavier aircraft will burn more fuel. Consequently, the amount of NAM
per unit of fuel decreases.
A higher ambient temperature (less dense air), results in a loss of engine
efficiency. Consequently, more fuel will be burnt per unit of thrust. SR
decreases. The Specific Fuel Consumption increases.
Question N° 72
Correct Answer – B
CS 23.51 Take-off speeds
(b) For normal utility and aerobatic category aeroplanes, the speed at 15 m (50
ft) above the take-off surface level must not be less than –
(2) For single-engined aeroplanes, the higher of –
(i) A speed that is shown to be safe under all reasonably expected conditions,
including turbulence and complete engine failure; or
(ii) 1·20 V S1 .
VS1 = 82 kt / 1.2 = 68 kt
Question N° 73
Correct Answer – B
If an engine failes, the pilot will put the aircraft into a glide at the best glide
speed, V MD .
According to the Annex IV - Part-CAT - GM1 CAT.POL.A.320: En-route - Single-
engined aeroplanes:
ENGINE FAILURE: (b) The operator should first increase the scheduled
engine-inoperative gliding performance data by 0.5 % gradient when
verifying the en-route clearance of obstacles and the ability to reach a
suitable place for a forced landing.
Thus, the en-route glide gradients will be steeper than the gross gradients, by
0.5%.
The question asks for the net distance, so we use the net gradient for our
calculations. The assumed en-route gradient shall be the gross gradient of
descent increased by a gradient of 0.5% (worse than average gradient), thus
giving us a safety margin. So, we use a descent gradient of 8.5 %.
Using the formulae given, we get:
1. Still air distance = (Height difference x 100) / Net gradient % = [(8000 ft - 1500
ft) x 100] / 8.5 = 76 470 ft or 76 470 ft/6080 = 12.58 NM.
2. Ground distance = Still air distance x (GS/TAS) = 12.58 NM x (200 kt - 20 kt) /
200 kt = 11.3 NM.
NOTE: The gradient may also be given as a Lift/Drag ratio. For example, if you are
given a L/D ratio 12:1, then if gliding with V MD , your gradient will be 1/12 = 0.083
or 8.33 %.
Question N° 74
Correct Answer – C
Using the given formula and the figure's data, we get the height difference, when
over the power lines at the extension of Rwy 09 (1.5 NM after the end of
TODA): Height Difference = ((GD x TAS)/GS) x Gradient/100 = ((1.5 NM x 6 080 ft
x 133 kt) / (133 kt + 10 kt)) x 5/100 = 424 ft AMSL.
For a single-engined aeroplane, we assume that the required climb gradient will
be achieved at the end of TODA at the screen height of 50 ft. Thus, the height
difference above the power lines is: 424 ft + 50 ft = 474 ft AMSL.
Since, the power lines' elevation is 400 ft AMSL, the aircraft will clear the power
lines on the extended centre line by: 474 ft - 400 ft = 74 ft.
Question N° 75
Correct Answer – B
Jet Aircraft Endurance
Maximum endurance will occur at minimum fuel flow. In a jet aircraft means
minimum thrust and therefore minimum drag, V M D.
Propeller Aircraft Endurance
Minimum fuel flow for a propeller aircraft occurs when power required is
minimum, so the speed to fly for endurance is V MP . V M P is minimum power to
maintain straight and level flight, always less than V M D therefore the speed is
unstable.
Jet Aircraft Range
The greatest still air range will occur when we get the largest TAS for the
smallest power thrust required, the best TAS/DRAG ratio. This point lies at the
tangent of the power thrust curve, 1.32V M D .
Propeller Aircraft Range
The greatest still air range will occur when we get the largest TAS for the
smallest power required and not thrust. This point lies at the tangent of the
power curve, V M D .
Jet Propeller
Question N° 76
Correct Answer – A
CS 25.109 Accelerate-stop distance
(a) The accelerate-stop distance on a dry runway is the greater of the following
distances:
(1) The sum of the distances necessary to –
(i) Accelerate the aeroplane from a standing start with all engines
operating to V E F for take-off from a dry runway;
(ii) Allow the aeroplane to accelerate from V EF to the highest speed reached
during the rejected take-off, assuming the critical engine fails at V EF and
the pilot takes the first action to reject the take-off at the V 1 for take-off
from a dry runway; and
(iii) Come to a full stop on a dry runway from the speed reached as
prescribed in sub-paragraph (a)(1)(ii) of this paragraph; plus
(iv) A distance equivalent to 2 seconds at the V 1 for take-off from a dry
runway.
(2) The sum of the distances necessary to –
(i) Accelerate the aeroplane from a standing start with all engines
operating to the highest speed reached during the rejected take-off,
assuming the pilot takes the first action to reject the take-off at the V 1 for
take-off from a dry runway; and
(ii) With all engines still operating, come to a full stop on a dry runway
from the speed reached as prescribed in subparagraph (a)(2)(i) of this
paragraph; plus
(iii) A distance equivalent to 2 seconds at the V 1 for take-off from a dry
runway.
Question N° 77
Correct Answer – C
At cruising altitude an airliner will be flying Mach number, so the operational
limit is the M MO (Maximum Operating Mach Number). The aircraft would initially
descend maintaining a constant mach number. At the crossover altitude, the
limiting speed will become V M O , from which point, the aircraft should be flown at
a constant IAS.
If the aircraft was to keep descending at a constant Mach, the TAS and IAS
would keep increasing, leading to a VMO overspeed situation. Therefore, at the
changeover altitude, the flight crew must stop flying at a Mach number and fly at
constant IAS.
The climb is carried out in two phases: the first at a constant IAS and the
second at a constant Mach Number, after the crossover altitude.
The descent is carried out in two phases: the first at a constant Mach
Number and the second at a constant IAS, after the crossover altitude.
Question N° 78
Correct Answer – A
Loose contaminants result in additional drag due to the combination of
displacement of the contaminant by the airplane tires and impingement of the
contaminant spray on the airframe. This contaminant drag provides an
additional force impeding acceleration during a takeoff, or assisting
deceleration during a rejected takeoff.
Question N° 79
Correct Answer – A
Refer to figure.
a) Enter the graph at aerodrome ambient temperature of +33ºC.
b) Move vertically to the aerodrome pressure altitude of 2 000 ft.
c) Travel horizontally left to the flap reference line and apply the appropriate
setting to read climb limit mass of approx. 57 900 kg.
d) Apply any corrections necessary:
“FOR PACKS OFF, INCREASE ALLOWABLE MASS BY 900 KG.”
To get the correct climb limited take-off mass, we should add 900 kg to 57 900
kg. However, the highest available option is 57 900 kg.
Question N° 80
Correct Answer – A
Refer to figure.
The Crossover Altitude is the altitude where a specific Indicated Airspeed (IAS)
becomes a specific Mach number (M). It is the altitude where a specified IAS
and Mach number represent the same TAS.
Below the Crossover Altitude, the climb/descent is performed maintaining a
constant IAS. Whereas above the Crossover Altitude, the climb/descent is
performed maintaining a constant Mach number. At the Crossover Altitude,
there is one value of TAS which corresponds to the given Mach number and the
given IAS at the same time.
In this case, the crossover altitude of this aircraft has been incorrectly raised
higher up. This is because the altitude where 250KIAS = M0.78 is higher than
the altitude where 250 KIAS = 0.75. (Draw an ECTM graph or use the finger trick
to prove this to yourself if necessary.)
As this is a tricky question requiring a lot of thought, let us go through both the
climb scenario and the descent scenario.
In the descent scenario, we are initially descending with constant Mach No., but
increasing IAS. As the CA is higher up than usual, we reach it earlier, and our IAS
is not able to increase up to its usual value, so our descent below the CA may be
at a lower speed, however, there is no chance of overspeed in the
descent scenario, either by breaching the V MO or the M MO . We start with a
constant Mach No., decreasing after the CA, and our IAS initially increases, but
to a lower value than usual, then remains constant.
Question N° 82
Correct Answer – A
TODA
The take-off distance available is the take-off run available plus any clearway
and cannot be more than 1.5 the TORA. If there is no clearway at the aerodrome,
then the take-off distance available will be the same length as the take-off run
available.
ASDA
Distance from the start of the take-off run to the nearest point in the direction of
take-off at which the aircraft cannot roll over the surface and be brought to rest
in case of an aborted take-off without risk of accident. ASDA consists of TORA
plus the stopway if available.
Question N° 83
Correct Answer – B
Refer to figure.
Power required is the product of drag multiplied by the TAS flown: Pwr required
= DRAG x TAS. Thus, with increasing TAS, parasite drag increases and as a
consequence the power required increases too.
The minimum power required is produced when the aircraft is flying with the
minimum power required speed (V MP ), which exists at the lowest point of the
power required curve.
For a propeller-driven aircraft, V MP is also the best endurance speed, which gives
the minimum power required to maintain level flight and is the point where the
product of speed and drag (DRAG x TAS) are at a minimum.
Any increase or decrease of the TAS above or below the VMP
correspondingly, increases the power required and as a result the fuel flow and
decreases the aircraft’s endurance.
....................................................................................................................................................................
Question N° 84
Correct Answer – D
For a multi-engined Performance Class B aeroplane operated for Commercial Air
Transport, the landing distance must not exceed 70% of the Landing Distance
Available (LDA), which equates to a factor of 1.43.
For this question, the LDA needs to be factored down according to the field
length requirements on CAP 698 Section 3 - MEP1 p.17:
Question N° 85
Correct Answer – A
According to the Acceptable Means of Compliance (AMC) and Guidance
Material (GM) for CAT flights:
Question N° 86
Correct Answer – A
Refer to figure.
A Regulated Take-Off Weight (RTOW) table is a simplified form of table to use
and is produced for a specific aircraft type on a particular runway and shows
MTOM and speeds for a variety of temperatures and pressure altitudes,
sometimes giving different configuration options.
First of all, the wind direction 050 o is exactly in line with the runway 23L,
so the wind speed of 6 kt is a tailwind.
The question asks to take the more conservative data points and not
interpolate, so enter the RTOW chart from the "-10 kt column".
In each box, the Maximum Take-off Mass is at the top left. Move vertically
down the "-10 kt column", until you reach at MTOM just over the Actual
TOM given, 67050 kg.
We find this at 67.1 tonnes, which corresponds to an OAT of 63°C and is
equal to the Assumed/FLEX T° given.
In the same box, the numbers "29-29-33" correspond to the
speeds: V 1 (129 kt), V R (129 kt) and V 2 (133 kt), accordingly.
QNH is 1003 hPa, so apply the corrections: 0, 0, +1 to the above speeds
for "QNH 1013 -10 hPa".
Additionally, apply the corrections: -6, -3, -2 to the above speeds for Wet
runway.
No corrections are required for Engine anti-ice and Packs.
Finally, after applying the required corrections, the speeds for a "reduced
thrust take-off" on the 23L dry runway will be:
1. V 1 = 129 - 6 = 123 kt
2. V R = 129 - 3 = 126 kt
3. V 2 = 133 + 1 - 2 = 132 kt
Question N° 87
Correct Answer – C
Refer to figure.
Start with Drift down level off value.
(1) Enter the graph on the left scale at a pressure altitude of 16 000 ft.
(2) Travel horizontally to the right so that you intersect the 60 000 kg* reference
line. This intersection occurs approximately at 1/3 of distance between the 1
000 and 1 500 kg reference dashed lines => we will, therefore, burn around 1
150 kg of fuel.
(3) Track vertically down and read the result of approx. 31 min.
(4) Continue down and correct for a a 25 kt tailwind by following the reference
lines. Read a ground distance from engine failure of approximately 182 NM.
*Note: The equivalent gross mass of 60 000 kg comes from Gross Mass at engine
failure (58 050 kg) + the Engine Anti-ice ON correction (1 950 kg).
Question N° 88
Correct Answer – B
Refer to figure.
Power required is the power needed at any given speed to overcome the
particular amount of drag that exists at that speed and Power available is the
rate of application of thrust at a given speed. Both powers are given by the
formulae:
The aircraft flying at constant lift, resulting from constant Indicated Airspeed
and angle of attack, will essentially fly at a higher True Airspeed at a higher
altitude, because the loss of air density must be compensated for by an
increased speed of flight to maintain the required dynamic pressure on the
wings. Thus, the power required increases with increasing altitude, moving the
Power Required vs. TAS up and right along the tangent to the origin.
Thrust produced by an engine decreases with altitude, because of the
decreasing air density, which does not allow the engine to burn as much fuel.
Also, the True Airspeed will increase for a constant Indicated Airspeed, but at a
lower rate than the thrust reduces. Thus, the power available will decrease with
increasing altitude and the "Power availbale vs. TAS" curve will move down and
right.
Question N° 89
Correct Answer – A
Refer to figure.
Enter the graph at an OAT of +8ºC. Track vertically upwards to a pressure
altitude of 85 ft: it extends beyond the limits of the graph, which means it
extends outside the aircraft structural limit.
Note: This question is ambiguous, and it seems that there are 2 correct answers.
"it cannot be determined." is essentially correct, because the question does
actually ask for the MTOM, and that's indeterminable. Perhaps the original
question provides further info which makes the correct option clear.
Question N° 90
Correct Answer – C
The total drag is made up of two components: the induced drag (the lift
dependent drag), which is high at low speeds and the parasite drag (resistance
felt as a drag), which is greatest at high speeds. The induced and parasite drag
can be added together to create the known "total drag curve". The lowest point
of the total drag curve corresponds to the minimum drag speed, V M D , where the
induced drag equals to the parasite one.
The shape and the position of the total drag curve on a "Drag vs. Speed" graph
depends on many factors, one of which is the aircraft's mass change.
On every flight, the mass steadily decreases as the fuel is burned off. With a
decreased mass, the parasite drag stays unchanged, because the shape of the
aircraft is unchanged, but the lower value of the lift required decreases the
induced drag. Thus, the left hand side of the total drag curve moves down and
left. As a consequence, the curve has a bottom point further to the left and the
V M D decreases.
The figure that represents the above situation, as much as possible, is Figure 2.
Question N° 91
Correct Answer – A
Once in the air the headwind works against the aircraft's progress: The
groundspeed of the aircraft is equal to its airspeed minus the headwind, so for
instance, for a 10 kt headwind, while you're cruising at 100 knots airspeed you're
only making 90 knots over the ground. We can conclude that a stronger
headwind means that the groundspeed is lower than expected.
Consequently, it will take longer to travel the horizontal distance from TOD. If
the rate of descent remains the same, the aircraft will arrive at the required level
before the planned position. Therefore, the rate of descent should be reduced.
Question N° 92
Correct Answer – B
CAP 698 – Landing MEP1
Field Length Requirements
a) The landing distance, from a screen height of 50 ft, must not exceed 70% of
the landing distance available, i.e. a factor of 1.43.
b) If the landing surface is grass up to 20 cm long on firm soil, the landing
distance should be multiplied by a factor of 1.15.
c) If the METAR or TAF or combination of both indicate that the runway may be
wet at the estimated time of arrival, the landing distance should be multiplied
by a factor of 1.15.
d) The landing distance should be increased by 5% for each 1% downslope. No
allowance is permitted for upslope.
e) The despatch rules for scheduled (planned) landing calculations are in JAR-
OPS 1.550 (c)
Question N° 93
Correct Answer – B
Using the given formula and the figure's data, we get the height difference, when
above the trees at the extension of Rwy 18 (2 NM after the end of TODA): Height
Difference = ((GD x TAS)/GS) x Gradient/100 = ((2 NM x 6080 ft x 124 kt) / (124
kt - 10 kt)) x 9/100 = 1190.4 ft AMSL.
For a single-engined aeroplane, we assume that the required climb gradient will
be achieved at the end of TODA at the screen height of 50 ft. Thus, the height
difference above the trees is: 1190.4 ft + 50 ft = 1240.4 ft AMSL.
Since, the trees' elevation is 800 ft AMSL, the aircraft will clear the trees on the
extended centre line by: 1240.4 ft - 800ft = 440.4 ft.
Question N° 94
Correct Answer – B
CLEARWAY:
Question N° 97
Correct Answer – B
SPECIFIC FUEL CONSUMPTION
Specific fuel consumption (SFC) in a jet is the fuel flow per unit of thrust, while
SFC for a propeller is the fuel flow per unit of power.
The SFC is only an engine consideration and is not affected by drag, which is an
airframe consideration.
In a turbojet engine, SFC is lowest when the air temperature is low and the
engine is running at its design rpm of approximately 90 to 95% rpm.
This means that SFC is proportional to temperature.
It also means that the engine is most efficient at high altitude where the thrust
required to overcome drag is approximately 90 to 95% of the thrust available.
Question N° 98
Correct Answer – B
Maximum Specific Range over the Ground (SRG) is the greatest ground range
covered for a specific fuel flow.
The specific fuel consumption (SFC) for a turbine engine improves its efficiency
as the temperature decreases. That means that, SFC will reduce as the aircraft
climbs towards the tropopause and then once in stratosphere it stays broadly
the same as the aircraft continues to climb. SFC also increases almost linearly
as speed increases.
Thus, the SFC occurs at low IAS, at low temperatures and at high altitudes.
The greatest SRG will occur when we get the highest GS for the lowest power
required.
Thus, for a propeller aeroplane, the increase in power required, caused by an
increasing TAS in the climb, offsets the gains in SFC and SRG as you climb.
Question N° 99
Correct Answer – D
Refer to figure.
First of all, we must insert a Pressure Altitude in the graph and we are given a
True Altitude (based on QNH). Therefore, we must convert it into a PA: Let's
assume 1 hPa = 27 ft/hPa
Now that we have calculated the Pressure Altitude, we are ready to enter the
graph:
(1) Enter the graph at the bottom left at 13ºC. Draw a vertical line up until you
intersect the Pressure Altitude of 5 541 ft.
(2) From this point, continue horizontally to the right until you intersect the "REF
LINE". Thereafter, continue diagonally up and to the right to the value of 3 100
lbs.
(3) Continue horizontally to the right and read the RATE OF CLIMB ft/min value
of 1140 ft/min.
(4) From this point, continue horizontally until the next "REF LINE". Now, draw a
diagonal line up and to the right until you intersect the imaginary line which
corresponds to 110 KT IAS. Thereafter, continue horizontally to the right and
read a value of approx. 10.1% for CLIMB GRADIENT.
Question N° 100
Correct Answer – D
CS 25.119 Landing climb: all-engines-operating
In the landing configuration, the steady gradient of climb may not be less than
3·2%, with the engines at the power or thrust that is available 8 seconds
after initiation of movement of the power or thrust controls from the minimum
flight idle to the go-around power or thrust setting (see AMC 25.119); and
(a) In non-icing conditions, with a climb speed of VREF determined in
accordance with CS 25.125(b)(2)(i); and
(b) In icing conditions with the “Landing Ice” accretion defined in Appendix
C, and with a climb speed of VREF determined in accordance with CS
25.125(b)(2)(ii).
Question N° 101
Correct Answer – B
Engine Failure and Drift Down
In the case of an engine failure, the remaining thrust is not sufficient to balance
the drag force and the cruise speed cannot be maintained.The only solution is to
descend to a lower flight altitude, where the remaining engine can provide
enough thrust to balance the drag and allow level flight.
As the airplane descends into the lower atmosphere where density is greater,
the remaining engine can develop more thrust which will equal the drag force,
this is the GROSS level-off altitude, but would give no performance margin. So
the DRIFT DOWN PROCEDURE is continued to a lower altitude, the NET level-off
altitude.
Question N° 102
Correct Answer – C
This question is making a statement about how an aircraft must be built to
avoid buffet within certain parameters. Then you have to check each answer to
decide which one fits the statement fully.We will now analyse each possible
answer and find the most correct one.
When buffet becomes noticeable, it will probably be so severe that the pilot will
NOT be able to read the instruments or to control the aeroplane.
The statement does not mention that all buffet is severe buffet. Light buffet is
possible also, and is easy to correct, with no lasting damage, so this is
incorrect.
The aeroplane has entered an undesired state if high-speed buffet becomes
perceptible and recovery from this may be impossible.
Again, a small amount of high-speed buffet is easy to handle and is definitely
recoverable. Only severe buffet is undesirable and potentially unrecoverable,
again, incorrect.
NO high-speed buffet will occur at any speed up to VMO/MMO, unless the
aeroplane is approaching the stall.
The statement specified that there may be no perceptible buffeting condition in
the cruise configuration in straight flight at any speed up to VMO/MMO (other
than stall buffet). It only specifies straight flight though; and does not stop
high-speed buffet during manoeuvres within this speed range. Therefore, buffet
is possible within the speed range and this answer is incorrect.
High-speed buffet may occur at speeds around VMO/MMO during manoeuvres
away from straight flight.
This is true; as said previously, there is no part of the statement that
disallows high-speed buffet during manoeuvres, so it can occur.
Question N° 103
Correct Answer – B
Theoretically, the Long Range Cruise should be the same speed and technique
as Maximum Range. However, a higher power setting is usually recommended,
which still gives a good specific range (about 99% of the maximum range)
but increases the speed and decreases sector times. The Long Range Cruise
(LRC) speed is approximately 4% faster than maximum range speed with a fuel
penalty of approximately 1%.
Cost Index = Cost of Time ÷ Cost of Fuel
We can conclude that the LRC speed corresponds to a higher cost index
than the Maximum Range Speed.
Question N° 104
Correct Answer – A
Class A Net Take-off Distance Required
The take-off distance required is the greatest of the following three distances:
All engines operating. The horizontal distance travelled, with all engines
operating, to reach a screen height of 35 ft multiplied by 1.15
One engine inoperative (dry runway). The horizontal distance from BRP to
the point at which the airplane attains 35 ft, assuming the critical power
unit fails at V E F on a dry, hard surface.
One engine inoperative (wet runway). The horizontal distance from BRP to the
point at which the airplane attains 15 ft, assuming the critical power unit fails at
V E F on a wet or contaminated hard surface, achieved in a manner consistent with
the achievement of V 2 by 35 ft.
Question N° 105
Correct Answer – C
Refer to figure.
ICAO Annex 14
Chapter 1
Stopway. A defined rectangular area on the ground at the end of take-off run
available prepared as a suitable area in which an aircraft can be stopped in the
case of an abandoned take-off.
Clearway. A defined rectangular area on the ground or water under the control of
the appropriate authority, selected or prepared as a suitable area over which an
aeroplane may make a portion of its initial climb to a specified height.