Professional Documents
Culture Documents
120kl Ohsr
120kl Ohsr
BOQ 1- 14 of 14 Construction of VRCC OHSR having with internal dia of 6.00M with 0.15 meter free board and 0.15 meter Dead storage above bottom ring girder capable of holding 120000 Liters with the following sailent features as per departmental design plan and design, pattern with necessary earth connections complete, RCC Ladder inside OHSR with 0.45 m wide, Railing with 32mm dia GI Pipe of "A" class in two Rows around OHSR fixed in RCC (1:2:4) posts of size 150X150X750mm with 1.20m intervals around peripery on top of the OHSR, S&F of one no. of water level indicator of good quality with ebonite / copper float of approved pattern, construction of RCC Spiral stair case as per approved design with outside the reservoir from ground level to roof level, Supply and fixing of Lightening arrestor, including conductor and earthing etc. s/f of RCC fly proof ventilator with copper or steel fly proof mesh, s/f of Light weight Manhole frame and cover with 750 X 750mm as per IS specification 2 Nos, Waterproof plastering inside the tank with CM(1:3) 8mm thick and Plastering with CM(1:3) of 12mm thick out side the tank and supporting structure including Spiral stair case, Snowcem painting of approved colours in two coats over primary coat out side the OHSR and with 3 coats of epoxy paint to inner surfaces of the reservoir including bottom of the top slab, outside lettering with enamel paint of desired matter, including Cost of steel and its fabrication charges, Centering, curing and water leads etc, C/C of all materials and Labour charges etc,. complete, with fixing of Cast iron Pipes and specials for Inlet, Outlet & Scour arrangement from Tank up to Ground level as per the instructions of the department. But excluding cost of CI pipes and CI Specials which will be provide by the department, and arrangement for Over flow The OHSR structure as per PRED type design and foundation. The design bearing capacity of soils at 5 MTon/ Sq. meter for which drawings are enclosed and to be executed by the contractor. The above rates are arrived considering wind pressure as per BIS No 875/88. The rates are inclusive of VAT.
Qty 120000
Unit 1 ltr
Rate(INR) 13.19
2 3
S&D of 90mm dia 6Kg/ Cm2 PVC pipes complete Earth work excuvation for pipeline trench of size 0.70 X 1.00m in all types of soils except hard rock requires blasting ,lowering, laying & jointing PVC pipes ,testing of pipeline ,refilling the trench, watering & tamping of 90mm dia 6kgf/cm2 size including VAT S&D of 63mm dia 4Kg/ Cm2 PVC pipes complete Earth work excuvation for pipeline trench of size 0.70 X 1.00m in all types of soils except hard rock requires blasting ,lowering, laying & jointing PVC pipes ,testing of pipeline ,refilling the trench, watering & tamping of 63mm dia 4kgf/cm2 size including VAT S&D of 75mm dia 4Kg/ Cm2 PVC pipes complete Earth work excuvation for pipeline trench of size 0.70 X 1.00m in all types of soils except hard rock requires blasting ,lowering, laying & jointing PVC pipes ,testing of pipeline ,refilling the trench, watering & tamping of 75mm dia 4kgf/cm2 size including VAT S&D of 90mm dia 4Kg/ Cm2 PVC pipes complete Earth work excuvation for pipeline trench of size 0.70 X 1.00m in all types of soils except hard rock requires blasting ,lowering, laying & jointing PVC pipes ,testing of pipeline ,refilling the trench, watering & tamping of 90mm dia 4kgf/cm2 size including VAT S&D of 110mm dia 4Kg/ Cm2 PVC pipes complete
2000 2000
1 rmt 1 rmt
101.00 73.20
4 5
5500 5500
1 rmt 1 rmt
35.00 43.20
6 7
500 500
1 rmt 1 rmt
51.00 43.80
8 9
1200 1200
1 rmt 1 rmt
71.00 73.20
10
500
1 rmt
103.00
11
Earth work excuvation for pipeline trench of size 0.70 X 1.00m in all types of soils except hard rock requires blasting ,lowering, laying & jointing PVC pipes ,testing of pipeline ,refilling the trench, watering & tamping of 110mm dia 4kgf/cm2 size including VAT S&D of 140mm dia 4Kg/ Cm2 PVC pipes complete Earth work excuvation for pipeline trench of size 0.70 X 1.00m in all types of soils except hard rock requires blasting ,lowering, laying & jointing PVC pipes , testing of pipeline , refilling the trench, watering & tamping of 110mm dia 4kgf/cm2 size including VAT Construction of public stand post with RCC collar 75cm dia, RCC pipe 15 cm dia filled with CC(1:2:4) , S & F of 3/4" dia GI pipe and all necessary fixtures complete for finished item. ECV(INR): 2,816,050.00
500
1 rmt
73.95
12 13
500 500
1 rmt 1 rmt
167.00 74.75
14
20
No
1248.00
15
Operation and Maintenance of the "CPWS scheme to Kanagal, Regette, Chandur and other habitations" and to supply treated potable drinking Water to the ( 70 ) Habitations at the specified rate in various habitations of Nalgonda district (as given in the schedule), including cost and conveyance of all materials, all operating expenses, Maintenance of crew and all Labour wages / charges, ( i.e, Pump Operators / Electricians / Fitters / Helpers /Mechanics / Watchmen/ technical personnel / others personnel etc.,) involved in Operation and Maintenance of Pump Sets Electrical Transformers (pertainnig to Department), RSF water Treatment Plants, Chlorinators, Head Works, Trasmission Lines, all pipelines, all balancing and Service Reservoirs, sumps and Distribution Lines, Sluice Valves, Air Valves, scour valves, and all other sorts of valves, Public Stand Posts, land scaping including cost and conveyance of materials like Pipes, CID Joints, Valves, Repairs to Pump Sets etc., including rewinding of electrical motors, panel boards replacement of all spares and chlorinators and mixing of required quantity of bleaching powder/ Chlorine gas / Liquid Chlorine daily as per standard according to seasons and release water to all the habitations daliy to service resorvoirs / GLSRS / Sumps ( as per annexure I) with the specified quality but excluding Power consumption charges, VAT, insurance, Provident Fund contribution, but including all preventive and periodical maintenance of electrical and mechanical equipment, Plant and equipment hire charges, piece welfare expenses, rental for site offices, Godowns, Travel including all incidental and inevitable expenses in Operation and Maintenance of overall scheme execept monthly power consumption charges which will be paid by the department.
335920.00
kL
4.84
Amount(INR) 1582800
202000 146400
192500 237600
25500 21900
85200 87840
51500
36975
83500 37375
24960
2816050
1625852.80
S.No.
Specification No. 1 Construction of 1 No 800KL RCC ELSR of suitable design in a single compartment with a staging of 15m with dead storage of 0.15m and 0.30m free board above MWL. The salient features of the ELSR
Qty
Rate(INR) 9.35
Amount(INR) 7478400
(Rupees nine and thirty four paise only ) Construction of 1 No 800KL RCC ELSR of suitable design in a single compartment with a staging of 15m with dead storage of 0.15m and 0.30m free board above MWL. The salient features of the ELSR are 1) Average G.L. + 5.86 m 2) LWL +20.86 m 3) MWL +25.36 m With minimum two rows of columns & central dome. The minimum thickness for top roof slab shall be 100mm. The minimum thickness of bottom flat slab & dome shall be 200mm (with reinforcement on both faces) and uncracked section shall be adopted. All RCC components shall be of M30 grade. PCC base course shall be in (1:3:6) 150mm thick with 150mm projection on either sides of the annular raft footing. Minimum depth of foundation shall be 2.50m. (Measured at top of the base course). The SBC shall be adopted as per the report of soil investigation agency or the SBC analysis to be got done by the contractor separately whichever is less and shall be restricted to a certain values as per site conditions to be decided by the Superintending Engineer. Sand cushion of 0.60m shall be provided below PCC as leveling course in case of clayey soils, Galleries of 1.00m width and hand railing shall be provided both at floor level and roof level. Braces and ring beams shall be of uniform cross section with 1st brace at GL. Wind force shall be considered as 350Kg/M2 or all columns & containers as per relevent IS codes. Age factor and redistribution of moments are not allowed. Roof slab shall also be designed as uncracked section. Reservoir construction shall include fixtures and accessories Finishings of the ELSR should be done as per the specifications. Hoisting, laying, jointing and testing of CI pipe connections includes pipes, specials, bell mouths, valves, bends, etc., for inlet, outlet, scour & over flow connections including construction of masonry pits, surface boxes, etc and conveyance of CI D/F pipes, Specials valves etc. The pipes shall be cleaned after fixing and provided with 2 coats of anticorrosive black paint. Supply, delivery and fixing of the following accessories of best quality and as per specification or any other higher quality Fixture Including: a) A Balcony of 1 m width at floor slab level / middle ring beam level, top ring beam level with RCC post with GI pipe hand railing. b) CI light type manhole covers with frames of 600mm of IS make- 2 Nos c) RCC ventilators of 150 mm dia manufactured out of MS 8 mm sheet and fixed with mosquito proof wire mesh and painted with 2 coats of anticorrosive black paint 12 Nos d) RCC Phenol ventilators of 600mm size-1No e) RCC Laders of 450 mm width inside the reservoir- 2 Nos f) Dog legged stair case 1.0m fight width for access to the top of service reservoir with R.C.M Pradha 1No g)RCC hand railing 0.75 m height all round at floor level and roof level h) Water level indicator of float operated type with brass pulley, bracket, Nylon thread, PVC float, enamel gauge numbered in Mts and 1/10th of mt, with moving index -1No i) Lightening arrestor as per IS3070/1974- 1 No with all its accessories. Complete including earthing j) Providing 2 coats of weather proof emulsion paint of approved quality and shade to the outer surface of reservoir lettering all required fixtures, pipes, bends, valves, columns, braces, staircase, etc., k) Applying four coats of corroseal appoxy based coating system to the inner surface of side walls, floor slab and all round inner columns up to roof in base coat and 3 top coats on thoroughly prepared concrete slab surface each coat not exceeding 60 microns in dry film thickness, total thickness 240 microns l) Testing of the reservoir for water tightness including cost and conveyance of water as per class 10 of IS 3370 (part-I) of 1965 and shall satisfy the water tightness requirements as per class.10,12 of 3370 / 1965, emptying the service completed, leveling the site including disposal of surplus earth etc., the contractor has make his own arrangements for conveyance of CI pipes, specials, bolts, nuts, rubber packing and its conveyance to site. The tentative details of pipe connections are as follows : a) Inlet 300mm dia b) Outlet 300mm dia c) Overflow 300mm dia d) Scour 200mm dia M)Leveling the site N) Flooring ELSR area
Specification No. 2 Supply and delivery of the C.I pipes and specials valves for inlet
Qty
Unit 18026 1 Kg
Rate(INR) 70.41
Amount(INR) 1269210.66
(Rupees seventy and forty one paise only ) Supply and delivery of the C.I pipes and specials valves for inlet, outlet scour and over flow connections to site confirming to IS 1538- 1993 of standard / non standard including cost and conveyance, packing forwarding, transit risk etc., complete including cost and conveyance to site including all taxes and duties but excluding turn over tax for vertical connection.
Qty
Unit 3 1 No
Rate(INR) 42236 (Rupees forty two thousand two hundred thirty six only )
Amount(INR) 126708
Manufacture, supply and delivery of CID/F sluice valves confirming to IS 14846 / 2000 with amendments No 1&2 heavy duty with CI grade FG 260 as per IS 210. Two coats of primer suitable for EPOXY paints finish shall be applied to all metal surface and finally two coats of Epoxy paint. The valves shall be tested for (Closed and test) against Hydrostatic test requirement. The rates are including transportation, Central Excise duty and sales tax etc., the operation can be done with hand wheel / cap. ISI marked. Including cost and conveyance to site, insurance, packing, loading at factory and unloading at site etc., complete including all taxes and duties but excluding turn over tax. a)300 mm dia PN 1.60
Qty
Unit 1 1 No
Rate(INR) 22222 (Rupees twenty two thousand two hundred twenty two only )
Amount(INR) 22222
S.No. 1
Description
Qty 250000
Unit Liter
Rate 10.15
Amount 2537500
(1) Rate inclusive of three coats of epoxy paint to inner surface of the reservoir including roof dome. (2) The above rates be adopted for estimate purposes for construction of ELSR for a finished work including 2 coats of snow cem painting for external surfaces lettering, fixing of all required fixtures, pipes, bends, valves etc., for pipe connections, but excluding cost of pipes, bends and valves as per departmental designs and drawings. (3) The above rates applicable for wind pressures upto 350 kg/ sqm. If the ELSR is to be designed for seismic forces also, cost shall be arrived by working out detailed quantities based on the designs. (4) Fixtures include : (a) RCC or aluminium ladder inside 0.45m wide. (b) spiral staircase on the out side (c) Lightening arrestor, including conductor and earthing etc., (d) RCC ventilators with copper or stainless steel fly proof mesh (e) RCC final ventilators with copper or stainless steel fly proof mesh (f) Manholes frame and cover 0.75 x 0.75 m with frame as per IS specifications (light duty) -2 Nos. (g) Railing with 32 mm dia GI pipes (A class) in two rows around OHSR fixed in RCC (1:2:4) posts of size 100 x 75 x 75 mm with 1.5 m intervals around periphery on top of the OHSR for smaller capacities. (h) water level indicator of good quality with ebonite / copper float approved pattern 1 No.
Manufacture, supply and delivery of the following sizes of CID/F sluice valve confirming to IS 14846 / 2000 with amendments No. 1 & 2 heavy duty with CI grade FG 260 as per IS 210 two coats of primer suitable for epoxy paints finish shall be applied to all metal surface and finally two coats of Epoxy paint. The valves shall be tested for (closed end test) against hydrostatic test requirement. The operation can be done with hand wheel / cap. ISI marked, including cost & transportation to site with taxes excluding CED etc., complete as per SS and directed by the departmental authorities.(a) 150 mm dia sluice valve PN 1.6
Each
12507.25
37521.75
Manufacture, supply and delivery of the following sizes of CID/F sluice valve confirming to IS 14846 / 2000 with amendments No. 1 & 2 heavy duty with CI grade FG 260 as per IS 210 two coats of primer suitable for epoxy paints finish shall be applied to all metal surface and finally two coats of Epoxy paint. The valves shall be tested for (closed end test) against hydrostatic test requirement. The operation can be done with hand wheel / cap. ISI marked, including cost & transportation to site with taxes excluding CED etc., complete as per SS and directed by the departmental authorities.(b) 100 mm dia sluice valve PN 1.6
Each
8338.58
8338.58
Manufacture, supply and delivery of following sizes of cast iron pipes and specials confirming to IS No. 7181/1986, 5531 / 1988, 3950/1979 including cost and conveyance loading, unloading at site etc., complete including taxes excluding CED.(a) 150 mm dia x 2.00 m long CI D/F pipe
27
Each
4368.74
117955.98
Manufacture, supply and delivery of following sizes of cast iron pipes and specials confirming to IS No. 7181/1986, 5531 / 1988, 3950/1979 including cost and conveyance loading, unloading at site etc., complete including taxes excluding CED.(b) 150 mm dia x 0.90 m long CI D/F pipe
Each
2299.24
6897.72
Manufacture, supply and delivery of following sizes of cast iron pipes and specials confirming to IS No. 7181/1986, 5531 / 1988, 3950/1979 including cost and conveyance loading, unloading at site etc., complete including taxes excluding CED.(c) 100 mm dia x 2.00 m long CI D/F pipe
Each
2677.32
24095.88
Manufacture, supply and delivery of following sizes of cast iron pipes and specials confirming to IS No. 7181/1986, 5531 / 1988, 3950/1979 including cost and conveyance loading, unloading at site etc., complete including taxes excluding CED. (d) 100 mm dia x 0.90 m long CI D/F pipe
Each
1413.73
1413.73
Manufacture, supply and delivery of following sizes of cast iron pipes and specials confirming to IS No. 7181/1986, 5531 / 1988, 3950/1979 including cost and conveyance loading, unloading at site etc., complete including taxes excluding CED. (e) 150 mm dia CI bell mouth
Each
678.38
2035.14
Lowering the following sizes of CI or DI pipes and fittings with flanged ends carefully in to the trenches and laying them true to alignment and gradient including all sundries, but excluding conveyance for source of supply etc., complete to SS as per BIS No. 3114/85. (a) 150 mm dia
57
Rmt
26.5
1510.5
10
Lowering the following sizes of CI or DI pipes and fittings with flanged ends carefully in to the trenches and laying them true to alignment and gradient including all sundries, but excluding conveyance for source of supply etc., complete to SS as per BIS No. 3114/85.(b) 100 mm dia
19
Rmt
25.25
479.75
11
Jointing the following sizes of CI pipes fittings and valves with flanged ends including cost of jointing materials such as bolts, nuts, rubber inserting, white lead and including filling with water lead upto 500 m and testing to required pressure etc., complete as per BIS 3114/85 (a) 150 mm dia
31
Each
612.97
19002.07
12
Jointing the following sizes of CI pipes fittings and valves with flanged ends including cost of jointing materials such as bolts, nuts, rubber inserting, white lead and including filling with water lead upto 500 m and testing to required pressure etc., complete as per BIS 3114/85 (b) 100 mm dia
10
Each
384.66
3846.6
13 14 15
Labour charges for lowering and keeping in position of the flowing sizes of CI sluice valves, reflux valves and scour valves (a) 150 mm dia Labour charges for lowering and keeping in position of the flowing sizes of CI sluice valves, reflux valves and scour valves (b) 100 mm dia Construction of brick masonry sluice valve pit as per type design drawing including seinarage charges and cost of all materials like steel, cement, sand, aggregate, bricks and labour charges etc., complete as per directions of departmental authorities. (a) Earth work excavation in loamy and clayey soils like black cotton soils, red earth and ordinary gravel for sluice valve pits.
3 1 10
68.13 44 93.76
204.39 44 937.6
16
Construction of brick masonry sluice valve pit as per type design drawing including seinarage charges and cost of all materials like steel, cement, sand, aggregate, bricks and labour charges etc., complete as per directions of departmental authorities.(b) CC (1:4:8) mix using 40 mm m/c HBG (SS5) metal
0.8
Cum
3113.51
2490.81
17
Construction of brick masonry sluice valve pit as per type design drawing including seinarage charges and cost of all materials like steel, cement, sand, aggregate, bricks and labour charges etc., complete as per directions of departmental authorities.(c) Brick masonry work in CM (1:5) mix using bricks second class
Cum
3399.1
20394.6
18
Construction of brick masonry sluice valve pit as per type design drawing including seinarage charges and cost of all materials like steel, cement, sand, aggregate, bricks and labour charges etc., complete as per directions of departmental authorities.(d) plastering in CM (1:3) mix 12 mm thick
30
Sqm
113.23
3396.75
19
Construction of brick masonry sluice valve pit as per type design drawing including seinarage charges and cost of all materials like steel, cement, sand, aggregate, bricks and labour charges etc., complete as per directions of departmental authorities.(e) RCC (1:11/2:3) mix using 20 mm m/c HBG metal
1.2
Cum
5789.39
6947.27
20
Construction of brick masonry sluice valve pit as per type design drawing including seinarage charges and cost of all materials like steel, cement, sand, aggregate, bricks and labour charges etc., complete as per directions of departmental authorities.(f) Fe415 steel for cover slab.
215
Kg
50.63
10885.45
21
Construction of brick masonry sluice valve pit as per type design drawing including seinarage charges and cost of all materials like steel, cement, sand, aggregate, bricks and labour charges etc., complete as per directions of departmental authorities.(g) Refilling and leveling with excavated earth.
10
Cum
21.88
218.8
22
Providing additional quantity of VRCC M 30 grade using 20 mm HBG graded metal as per IS 303 including cost of materials, centering, curing, conveyance, machine mixing, vibrating, labour charges etc., complete for finished item of work for seismic design.
69
Cum
10156.81
700819.89
23
Providing additional quantity of FE 415 grade steel including cost of materials, fabrication, binding wire etc., complete for finished item of work for seismic design. ECV(INR): 3,786,388.00 ( Rupees thirty seven lacs eighty six thousand three hundred eighty eight only )
6.9
MT
40500
279450
3786387.26
percentage
S.No.
Unit
Rate(INR)
Amount(INR)
125000 1 liter
1567000
Construction of 1 no 125 KL RCC ELSR of Suitable design in a single compartment with a staging of 15 mts dead storage of 0.15 Mts and 0.30mts free board above MWL. The salient features of the ELSR are 1. Average G.L -- + 11.00 M 2. L.W.L -- + 26.00 M 3. M.W.L -- + 30.00 M The minimum thickness for top roof slab/dome shall be 100 mm. The minimum thickness of bottom flat slab & dome shall be 200 mm (with reinforcement on both faces) and uncracked section shall be adopted. All R.C.C components shall be m.30 grade. PCC Base course shall be in (1:3:6) of 150mm thick with 150mm projection on either side of the annular raft footing. Minimum depth of foundation shall be 2.50mts. (Measured at top of the base course). The SBC shall be adopted as per the report of soil investigation agency or the SBC report to be got done by contractor separately which ever is less and shall be restricted to a certain value as per the site conditions to be decided by the Superintending Engineer. Sand cushion 0.60 mts shall be provided below PCC as leveling course in case of clayey soils, galleries of 0.75 mts width and hand railing shall be provided both at floor level and at roof level. Braces and ring beams shall be of uniform cross section with 1st brace at GL. Wind forces shall be considered as 350 kg per sqm on all columns & containers. Age factor and redistribution of moments are not allowed. Roof slab shall also be designed as uncracked section. Reservoir construction shall include fixtures and accessories. Finishings of the ELSR should be done as per the specifications. Hosting, Laying, jointing and testing of CI pipe connections includes pipes, specials, bell mouths valves, bends, etc., for inlet, outlet, scour over flow connection including construction of masonry pits, surface boxes, etc., The pipes shall be cleaned after fixing and provided with 2 coats of anticorrosive black paint. Supply, delivery and fixing of the following Specification Qty Unit Rate(INR) Amount(INR) accessories of best quality and as per specification or any other higher quality. 1. C.I. Light type manhole covers of 600 mm No. as per I.S. make - 2 nos. 2. RCC Aluminum ladders of 450 mm width inside the reservoir--2 Nos. 3. Water level indicators of float operated2 ss with brass pulley, bracket, Nylon thread, PVC float,208668 gauge numbered in Mts. And 1/10th of mt, type enamel 1 1 Job 208668 with moving index -- 1 No. 4. Lightening arrestor as per IS; 3070/1974 - 1 No 5. RCC phenol ventilators of 600 mm size (Rupees two with copper or stainless steel fly proof mesh- 1 No. 6. RCC / MS ventilators of 150 mm dia manufactures out of MS 8mm lacs eight sheet and fixed with mosquito proof wire mesh of copper or stainless steel and painted with 2 coats of anticorrosive black thousand six paint -- 6 Nos. 7. Spiral stair case 1.0 m width for access to the top of service reservoir out side with necessary hand railing 1 No 8. Providing 2 coats of whether proof paint of approved hundred sixty outer surface of reservoir, columns, braces, quality to the eight only ) staircase, etc over the primary coat of white cement wash. 9. Applying four coats of corroseal apoxy based coating system to the inner faces of side walls, floor slab and all round inner columns up to MWL in base coat and 3 top coats on thoroughly prepared concrete sub surface. Each coat not exceeding 60 microns in dry film thickness, total thickness 240 microns including cost of all labour charges etc., complete for finished item of work. 10. Testing of the reservoir for water tightness including cost and conveyance of water per CI.10 of IS 3370 (part-i) of 1965 and shall satisfy the water tightness requirements as per Cl.10,12 of 3370/1965, emptying the service reservoir after testing, cleaning, finishing etc., complete. Supply and delivery of the C.I pipes of surplus earth etc. The contractorand over flow his own arrangements for conveyance Levelling the site including disposal and specials for inlet, outlet scour has to make connections to site confirming to IS 1538- 1993 specials, valves and its conveyance to site. The tentative details of pipe connections are as etc., complete 150 of CI pipes, of standard / non standard including cost and conveyance, packing forwarding, transit risk follows: 1. Inlet including cost and 150 mm dia 3. Over flow 150all taxes 4. Scour 100 mm dia 11. turn over tax for vertical connection ( as in mm dia 2. Out let conveyance to site including mm dia and duties but excluding Railing with 32mm dia GI pipes (A class per separate sheet enclosed) in RCC (1:2:4) posts of size 100 x 75 x 75 mm with 1.5m intervals around periphery on top of two rows around OHSR fixed the OHSR 12. Leveling the site including disposal of surplus earth. The tender has to quote amount for completing the Specification which Unit Rate(INR) Amount(INR) service reservoir in all respects Qty will be taken as act value. 13. Fixing of CI D/F pipes, specials, and valves, including No. valve pits and painting all the pipes and specials, valves with 2 coats of anticorrosive black paint. 14. RCC balcony of 0.75 m width at middle ring beam level and roof slab level with necessary RCC/G.I pipes hand railing. 15. Man hole frame & cover 0.75 m x 0.75mss 3 with frame as per specification10 sqm 100 light duly 2 Nos Note: 1) Wind pressure 350 kg / sqm 2) The contractor 3670.88 36708.8 has to furnish his own design and get approved by the department. 3) Bearing capacity may be taken as per soil analysis report at the proposed site. 4) The contractor has to construct (Rupees threeELSR with above fixtures and as per above capacity RCC thousand six specifications. Wherever centering is to be done it should be done with steel centering only. hundred seventy and eighty eight paise only )
Providing Flooring the reservoir area with CC(1:3:6)100mm thick top plastered with CM(1:3)20mm thick etc completed as directed by the departmental officer in charge of the work as per ss
Sl no
1 2
Description
Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with initial lift of 3 mts and lead upto 50 m Filling foundation with sand in layers of 25 to 30 cm and compacting by watering, ramming as directed including cost of all materials, machinery, labour etc., complete with initial lead upto 50m and all lifts. Plain Cement concrete (1:4:8) using 40 mm metal with concrete mixture. All work upto plinth level. Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(a) For column footings
Qty
16 26
Unit
Cum Cum
Rate
76 1651
Amount
1175 42387
3 4
2 5
Cum Cum
3147 5016
6104 22775
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(b) For pedelstals
Cum
5027
1810
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(c) For columns
Cum
5260
9416
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(d) For plinth beam
Cum
5903
13991
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(e) For lintel beam
Cum
5830
7754
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(f) For sunshades of 0.60Mts wide with 0.075m thick at fixed end and 0.05m at free end .
13
Rm
145
1925
10
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(g) For sajjas of 0.60Mts wide with 0.075m thick.
14
Rm
174
2362
11
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade (h) For roof beams.
Cum
5830
10552
12
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade. (i) For roof slab (125mm thick)
46
1sqm
964
44132
13
46
1sqm
134
6124
14 15 16 17
Brick Masonry in CM (1:5) with Bricks traditional size 23 x 11 x 7 cms 2nd class Plastering with CM (1:3), 12 mm thick(A)For inside plastering Plastering with CM (1:3), 12 mm thick(B) For out side plastering Flooring with cement concrete 1:6:10, using 40mm metal, 100mm thick and plastered over with 12mm thick in CM (1:3) White washing two coats with whiting of approved quality to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost of all materials, labour charges and incidental such as scaffolding, lift charges etc., complete for finished item of work, but excluding conveyance charges of materials
22 166 106 30
3320 83 83 401
18
166
1sqm
23
3832
19 20 21 22 23 24
Distempering, 2 Coats with Water Bound Distemper Painting 2 coats over a primary coat on new wood work Painting 2 coats over a primary coat on new Iron work Supply and fabrication of HYSD steel Supply and fixing of iron grills Supply, fabrication and transportation of G.I. Pressed section doors and door frame of size 105 x 60 mm / 1.25 mm thick hallow metal pressed section and shutters made 1.0 mm thick two GI sheets having front sheet vertical embossing and rear sheet horizontal embossing both together spot welded. The rate is inclusive of hold pasts, MS. Oxidized hinges, tower blots, aldrop, handles etc., inclusive all taxes and of one coat of epoxy primer with heat treatment.
43 82 77 38 52 3500
25
Supply, fabrication and transportation of G.I. Pressed section doors and door frame of size 105 x 60 mm / 1.25 mm thick hallow metal pressed section and shutters made 1.0 mm thick two GI sheets having front sheet vertical embossing and rear sheet horizontal embossing both together spot welded. The rate is inclusive of hold pasts, MS. Oxidized hinges, tower blots, aldrop, handles etc., inclusive all taxes and of one coat of epoxy primer with heat treatment.
Sqm
3500
7350
26
Supply, fabrication and transportation of GI sheet pressed section windows with hallow metal section frame of 65 x 40 mm of 1.25 mm thick having vertical centrally portion with F4 8 section and shutter consists of Z or angle section frame and 0.8 mm thick vertically embossed GI sheet providing guard bars of 12 mm round MS bars at 110 mm c/c and handles, stays etc., inclusive all taxes and of one coat of epoxy primer with heat treatment.
Sqm
3750
27000
27
Collection and supply of Gravel including cost and conveyance of materials to work site, stacking to dept., gauge and labour charges etc., complete-1cum Spreading and compaction of Gravel including watering, rolling with 2T hand roller and barricading etc., complete with irrespective of thickness -10 cum
1440
1 Cum
239
343613
28
1440
1 Cum
23
33324
886768
Sl no
1 2
Description
Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with initial lift of 3 mts and lead upto 50 m Filling foundation with sand in layers of 25 to 30 cm and compacting by watering, ramming as directed including cost of all materials, machinery, labour etc., complete with initial lead upto 50m and all lifts. Plain Cement concrete (1:4:8) using 40 mm metal with concrete mixture. All work upto plinth level. Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(a) For column footings
Qty
16 26
Unit
Cum Cum
Rate
76 1651
Amount
1175 42387
3 4
2 5
Cum Cum
3147 5016
6104 22775
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(b) For pedelstals
Cum
5027
1810
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(c) For columns
Cum
5260
9416
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(d) For plinth beam
Cum
5903
13991
Supply and placing of the Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work for M-25 Grade(e) For lintel beam
Cum
5830
7754
17
Flooring with cement concrete 1:6:10, using 40mm metal, 100mm thick and plastered over with 12mm thick in CM (1:3) Supply and fabrication of HYSD steel
30
1 sqm
401
11894
22
1000
Kg
38
37922
155227