TECHNICAL DATA SHEET

Rev: 09, Date 27.03.2018

MACLINE® SDH
HIGH DENSITY POLYETHYLENE (HDPE) GEOMEMBRANES
MACLINE SDH is an high density polyethylene geomembrane (smooth surfaces on both sides) manufactured from
maximum quality polyethylene resins, duly contrasted, that comply with the most rigorous requirements established
for their use.
Geomembrane MACLINE SDH contains not less than 97% of pure polyethylene polymer and a balance not higher
than 3% of carbon black, antioxidants and thermal stabilizers. The product does not contain plasticizers or fillers
that could migrate over time.
Geomembrane MACLINE SDH are manufactured under permanent quality control and comply with national and
international standards.
SURFACE: SMOOTH/SMOOTH COLOUR: BLACK RAL CODE: -
RAW MATERIAL CHARACTERISTICS
FUNCTIONAL PROPERTIES
Property Unit Test Method Value
Property Unit Test Method Value
Membrane density (4) g/cm3 EN ISO 1183-1 >0.940
Low temperature °C EN 495-2 < -40
Melt flow index (4) g/10min EN-ISO 1133 < 3.00 brittleness (4)
@190 °C/5.0 kg
Dimensional stability (4) % EN 1107-2 <2
Carbon black content (4) % EN ISO 11358 2.0 - 3.0
ASTM D4218 Linear thermal expansion mm/mm/ ASTM D696 <1.76x10-4
coefficient (4) °C
Carbon black dispersion (4) - ISO 11420 <3
Water permeability (1,3) m3/m2 x EN 14150 <1x10-6
day
DURABILITY
Gas permeability (1,3) mol/m2 x ASTM D1434
Resistance to weathering; 3000h - EN 12224 Thickness <1.5 mm day 6.03 x 10-3
(1) Reduction of Thickness >2.0 mm 9.38 x 10-4
tensile strength Thickness of the % - -
Resistance to oxidation ; 85°C & and elongation
EN 14575 coextruded layer
90d (1) - <25% of original
values; OIT Fire resistance - ISO 11925-2 E
Resistance to microorganism (4) EN 12225 residual value
Resistance to chemicals (4) EN 14415 >55% 1. Property included in the CE mandate and reported in the
DoP of the product;
Resistance to leachate (4) EN 14414 As above with 2. Nominal values, in brackets minimum values;
additional loss
3. Tested properties; recorded values are reported on the roll
of the mass not
certificate issued at the production date;
higher than 25%
of the original 4. Property not included in the CE mandate, the values has to
mass be considered as informative data at the best of our
knowledge;
Stress crack resistance (1,2) h ASTM D5397 400 (>336) 5. Max tolerance equal to 10% however typical value equal to
EN 14576 6%.

GEOMEMBRANE
MACLINE SDH
© 2015 Maccaferri. All rights reserved. Maccaferri will enforce Copyright.
PHYSICAL - MECHANICAL PROPERTIES
Tested Property Unit Test Method 075 100 150 200 250 300
Thickness (2,3,4,5) mm EN 1849-2 0.75 1.00 1.50 2.00 2.50 3.00
Tensile properties

• Tensile strength at yield (2,3,4) N/mm2 18(>16) 18 (>16) 18 (>16) 18 (>16) 18 (>16) 18 (>16)
(2,4) N/mm EN-ISO 527-3 18 (>16) 27 (>24) 36 (>32) 45 (>40) 54 (>48)
• Elongation at yield (2,3,4) % 5 samples 11 (>9) 11 (>9) 11 (>9) 11 (>9) 11 (>9) 11 (>9)
Tensile strength at break (1,2,3) N/mm2 100 mm/min 32 (>26) 32 (>26) 32 (>26) 32 (>26) 32 (>26) 32 (>26)
(1,2) N/mm 32 (>26) 48 (>39) 64 (>52) 80 (>65) 96 (>78)
• Elongation at break (2,3) % >600 800 (>700) 800 (>700) 800 (>700) 800 (>700) 800 (>700)
Static CBR puncture resistance kN EN-ISO 12236 >2.0 3.2 (>2.7) 4.5 (>4.0) 5.5 (>5.0) 6.6 (>6.0) 7.0 (>6.3)
(1,2,3)
Tear Resistance (2,4) N/mm ISO 34-1 140 (>130) 140 (>130) 140 (>130) 140 (>130) 140 (>130)
(4) N 110 (> 100) 140 (>130) 210 (>185) 280 (>260) 350 (>325) 420 (>390)

For the optimisation and improvement process of the technical characteristics of the products, the producer reserves the factibility to modify standard and
characteristics at the product without any warning. The information contained herein is to the best of our knowledge accurate, but since the circumstances and
conditions in which it may be used are beyond our control, we do not accept any liability for any loss or damage, however arising, which results directly or indirectly
from the use of such information nor do we offer any warranty or immunity against patent infringement

Maccaferri (Malaysia) Sdn Bhd

Maccaferri operates under strict quality assurance and
Unit 511, Block G, Phileo Damansara 1, 46350 Petaling Jaya, Selangor D.E., Malaysia management procedures. Please visit the website of your
T: (60-3) 7955 7800 F: (60-3) 7955 7801 local subsidiary for details of their Certifications.
E: [email protected] Website: www.maccaferri.com/my