®

QR-25 Series

Model 216

Parts Manual
Record of Change 105

This manual contains important safety information and must be

carefully read in its entirety and understood prior to installation
by all personnel who install, operate and/or maintain this product.

On-line product registration, parts ordering and warranty information is available at www.quincycompressor.com

Manual No. 2022203800

July 2014 Edition

TABLE OF CONTENTS INTRODUCTION
Serial Number Identification ..................................2 This manual provides information for the QR-25
Series, Model 216 (per Record of Change 105) recip-
Ordering Replacement Parts .................................2 rocating compressor versions:
Quin-Cip Lubricant .................................................2
Crankcase Lubricant Capacity ..............................2 P Control Version P
Crankcase Group....................................................3 plain head assembly & no controls
Crankshaft Group ...................................................4
L Control Version L
Bearing Carrier Group............................................5 head assembly with 2 unloader towers &
Connecting Rod & Piston Group .......................6-7 a hydraulic unloader
Cylinder & Head Groups
LS Control Verions LS
Control Version P .............................................8-9
head assembly with 2 unloader towers, a
Control Versions L, LS, LVD ........................10-11
hydraulic unloader, & a pilot valve with
Head Assemblies a check valve assembly
Control Version P ..............................................12
Control Versions L, LS, LVD .............................13 LVD Control Verions LVD
Control Groups head assembly with 2 unloader towers, a
Version L ............................................................14 hydraulic unloader, & a pilot valve with
Version LS ..........................................................15 a lockout & check valve
Version LVD .......................................................16
The Model 216 is an aircooled, single stage, two
Pilot Valves............................................................17 cylinder, pressure lubricated compressor, with up to
Differential Setting Chart .....................................17 100 PSIG continuous pressure capability. It has a
Suction Valve Unloader Assemblies ...................18 3" bore, with a 2 1/2" stroke. This compressor can be
run at 400-900 RPM.
Gasket Set .............................................................19
Yearly Maintenance Kit ........................................19 Available options included in this manual:
-hooded air filter
Piston Pin Kit ........................................................19
-hooded air filter / silencer
Head Kit .................................................................19
Overhaul Kit ..........................................................19
Oil Pump Repair Kit ..............................................19
CHANGES
since previous printing dated January 2014:
Recommended Spare Parts .................................19
Bearing carrier group was redesigned with a new
Decals ....................................................................19
oil pump including an oil filter.

QR 216 Quincy Compressor

2022203800, July 2014 1 3501 Wismann Lane, Quincy IL - 62305-3116

MODEL & QUIN-CIP LUBRICANT
Record Refer to the chart below to order Quin-Cip-D or Quin-
SERIAL NUMBER of Cip compressor lubricant from your local authorized
Change No.
IDENTIFICATION Quincy distributor.

Quin-Cip-D Lubricant
(synthetic)

SAE 30 (ISO 100)

Quart 115468Q
Case (12 Qts.) 115438C

Model & Serial Number

Quin-Cip Lubricant
Identification Tag SAE 10W (ISO 32)
The model & unit serial number identification tag is Quart 112541Q032
located on the air tank top plate. Case (12 Qts.) 112541C032
SAE 20 (ISO 68)
Serial Number
Quart 112542Q068
___________
Case (12 Qts.) 112542C068
SAE 30 (ISO 100)
The basic compressor serial number decal is located Quart 112543Q100
on the bearing carrier of the basic compressor (op-
Case (12 Qts.) 112543C100
posite the flywheel side). Fill in the numbers from
your compressor unit and basic compressor in the SAE 40 (ISO 150)
corresponding spaces provided here, and reference Quart 2024601401
this page when ordering replacement parts. Case (12 Qts.) 2024601405

All replacement parts are to be ordered through

an authorized Quincy distributor. Insist on genuine
Quincy parts only! Failure to do so may void warranty.

ORDERING CAUTION !
Refer to the Quincy QR-25 Series instruction manual for
REPLACEMENT PARTS vital lubrication information.

Prompt service can be rendered on repair parts orders

if the following information is given: WARNING !
Item 1) the model number, record of change Follow all safety precautions outlined in the Quincy QR-25
Series instruction manual.
number, & serial number.
Item 2) the exact part number needed. (Do not
order by item numbers.)
CAUTION !
Item 3) the exact quantity needed. Do not operate this compressor without a totally enclosed
Item 4) the preferred type of transportation. belt guard or any other required safety equipment.

CRANKCASE LUBRICANT DANGER !

Air used for breathing or food processing must meet OSHA
CAPACITY 1910.134 or FDA 21 CFR 178.3570 regulations. Failure to
do so may cause severe injury or death.
Model Capacity
216 1 qt - 22 oz.
(1.6 lit.)

QR 216 Quincy Compressor

2022203800, July 2014 2 3501 Wismann Lane, Quincy IL - 62305-3116

 CRANKCASE GROUP 2021021701
Item Part
Number Qty. Number Description
1 1 5513X002 crankcase assembly
1.1 1 5513-002 crankcase
1.2 1 2523 bearing cup
2 * 1832D shim, bearing adjustment, .002 steel
3 * 1832 shim, bearing adjustment, .005, steel
4 * 1832A shim, bearing adjustment, .007, steel
5 * 1832B shim, bearing adjustment, .020, steel
6 * 1832C shim, bearing adjustment, .005, paper
7 1 5516X adjustment plate assembly
7.1 1 5516 plate, adjustment (.0015/.003 crankshaft end play)
7.2 1 6315 oil seal
8 4 123478-L10 hex. screw, 3/8-16 unc x .75, grade 5 (@ 30 ft.-lbs.)
9 1 2321 inspection plate
10 1 1598 gasket, inspection plate
11 1 110070-2 oil gauge
12 1 1301 pipe plug, 3/8 npt
13 1 110096 breather assembly
13.1 1 110094 breather body
13.2 1 110095 breather filter
13.3 1 123157-115 "o"ring, 3/32 wide x .88 o.d.
14 4 114629 hex. screw, 5/16-18 unc x 1.00, grade 5 (@ 150 in.-lbs.)
15 1 123157-112 "o"ring, 3/32 wide x .69 o.d.

Parts for use with diester or phosphate ester synthetic based lubricants
7.2 1 6315-001 oil seal
13.3 1 22749-115 "o"ring, 3/32 wide x .88 o.d.
15 1 22749-112 "o"ring, 3/32 wide x .69 o.d.

* Quantity as required
@ Indicates torque value (dry threads)

QR 216 Quincy Compressor

2022203800, July 2014 3 3501 Wismann Lane, Quincy IL - 62305-3116

CRANKSHAFT GROUP 110251

Item Part
Number Qty. Number Description
1 1 110219 crankshaft assembly
1.1 1 110218 crankshaft (N.S.S.; order 110219)
1.2 1 110234 orifice, 1/8 npt
1.3 2 2755S pipe plug, 1/8 npt
1.4 1 4019 bearing cone
1.5 1 2585 bearing cone
1.6 1 110705-F15 pin
2 1 1761 key
3 1 2917X sheave assembly
3.1 1 2917 compressor sheave, 14", 1G,B sect, ccw (N.S.S.; order 2917X)
3.2 2 124239-001 socket head screw, 3/8-16 unc X 2.75, Grade 5 (@ 30 ft.-lbs.)
3.3 2 124372-L02 square nut, 3/8-16 unc
3.4 2 110428W038 flatwasher, 3/8
OR
3 1 2918X sheave assembly
3.1 1 2914-R compressor sheave, 14", 2G,B sect, cw (N.S.S.; order 2918X)
3.2 1 123478-N18 hex. screw, 1/2-13 unc x 2.25, Grade 5 (@ 30 ft.-lbs.)
3.3 1 124372-N02 square nut, 1/2-13 unc
3.4 2 110428W038 flatwasher, 3/8
N.S.S. = Not Sold Separate
@ Indicates torque value (dry threads)

1.3 1.4

1.1 1.6

3.1
1.3
2

1.2

1.5
3.2

3.4

3.3

QR 216 Quincy Compressor

2022203800, July 2014 4 3501 Wismann Lane, Quincy IL - 62305-3116

 BEARING CARRIER GROUP 2024400360

QR 216 Quincy Compressor

2022203800, July 2014 5 3501 Wismann Lane, Quincy IL - 62305-3116

CONNECTING ROD & PISTON GROUP 110260
(2 required per compressor)

Cross Sectional View

of
Piston & Rings typical
pip mark
location
(top of ring)

Stagger ring gaps

during assembly!

QR 216 Quincy Compressor

2022203800, July 2014 6 3501 Wismann Lane, Quincy IL - 62305-3116

 CONNECTING ROD & PISTON GROUP 110260
(2 required per compressor)

Item Part
Number Qty. Number Description
1 1 110703X connecting rod assembly (N.S.S.; order 110703X1)
1.1 1 110703 connecting rod (N.S.S.; order 110703X1)
1.2 1 6440 connecting rod bushing (can not be purchased; order 6440SR)
1.3 2 3532 connecting rod bolt 5/16-24 unf
1.4 2 111260-002 connecting rod washer
2 2 8648 retaining ring
3 1 110190-008 piston pin
4 1 1531-001 piston
5 2 6451 oil ring rail
6 1 6450 oil ring expander
7 3 1648 compression ring
8 2 2824 con rod bearing insert (N.S.S.; order 2824PR)
9 2 124471-K08 locknut, 5/16-24 unf (@ 19 ft.-lbs.)

Maintenance Parts
*1 2824PR inserts (pair), con rod bearing,(standard)
*1 2824-010PR inserts (pair), con rod bearing, (.010 oversize)
1 6440SR bushing
1 1531-011 piston (.010 oversize)
1 1531-021 piston (.020 oversize)
2 6452A Ring Set (standard) no color code
includes compression ring, oil ring rails & expander (for one piston)
2 4425-010 Ring Set (.010 oversize; light blue)
includes compression rings, oil ring rails & expander (for one piston)
2 4425-020 Ring Set (.020 oversize; yellow)
includes compression rings & oil ring
2 1531X050 Piston Assembly (standard)
includes piston, piston pin, retaining rings & ring set
2 1531X011 Piston Assembly (.010 oversize)
includes piston, piston pin, retaining rings & ring set
2 1531X021 Piston Assembly (.020 oversize)
includes piston, piston pin, retaining rings & ring set
2 4425-020 Ring Set (.020 oversize; yellow)
includes piston, piston pin, retaining rings & ring set
2 110703X1 Replacement Connecting Rod Assembly
includes connecting rod assembly, locknuts & con-rod bearing inserts

N.S.S. = Not Sold Separate

@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.
* 1 pair required for each connecting rod assembly.

QR 216 Quincy Compressor

2022203800, July 2014 7 3501 Wismann Lane, Quincy IL - 62305-3116

CYLINDER & HEAD GROUP 110252
(control version P)

QR 216 Quincy Compressor

2022203800, July 2014 8 3501 Wismann Lane, Quincy IL - 62305-3116

 CYLINDER & HEAD GROUP 110252
(control version P)

Item Part
Number Qty. Number Description
1 1 1911P head assembly
2 1 1943 gasket
3 1 1913 cylinder
4 1 1594 gasket, cylinder
5 6 123478-L14 hex. screw, 3/8-16 unc x 1.25, grade 5 (@ 30 ft.-lbs.)
6 6 123115-06C lockwasher, 3/8
7 1 110377F075 filter
or
7 1 110377S075 filter/silencer
8 4 90386-L12 counterbore screw, 3/8-16 unc x 1.00, grade 8 (@ 30 ft.-lbs.)
9 2 1936 hex. screw, 3/8-16 unc x 3.00, grade 5 (@ 30 ft.-lbs.)
10 2 1836 washer

Maintenance Parts
11 1 110377E075 air filter element
1911X38P Replacement Head Assembly
includes head assembly & head gasket

@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.

QR 216 Quincy Compressor

2022203800, July 2014 9 3501 Wismann Lane, Quincy IL - 62305-3116

CYLINDER & HEAD GROUP 110255
(control versions L, LS & LVD)

QR 216 Quincy Compressor

2022203800, July 2014 10 3501 Wismann Lane, Quincy IL - 62305-3116

 CYLINDER & HEAD GROUP 110255
(control versions L, LS & LVD)

Item Part
Number Qty. Number Description
1 1 1911UU head assembly
2 1 1943 gasket
3 1 1913 cylinder
4 1 1594 gasket, cylinder
5 6 123478-L14 hex. screw, 3/8-16 unc x 1.25, grade 5 (@ 30 ft.-lbs.)
6 6 123115-06C lockwasher, 3/8
7 1 110377F075 filter
or
7 1 110377S075 filter/silencer
8 4 90386-L12 counterbore screw, 3/8-16 unc x 1.00, grade 8 (@ 30 ft.-lbs.)
9 2 1936 hex. screw, 3/8-16 unc x 3.00, grade 5 (@ 30 ft.-lbs.)
10 2 1836 washer

Maintenance Parts
11 1 110377E075 air filter element
1911X38L Replacement Head Assembly
includes head assembly, head gasket, copper tube & fittings

@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bring
each fastener to the recommended torque specification in even increments.

QR 216 Quincy Compressor

2022203800, July 2014 11 3501 Wismann Lane, Quincy IL - 62305-3116

HEAD ASSEMBLY 1911P
(control version P)

QR 216 Quincy Compressor

2022203800, July 2014 12 3501 Wismann Lane, Quincy IL - 62305-3116

 HEAD ASSEMBLY 1911UU
(control versions L, LS & LVD)

QR 216 Quincy Compressor

2022203800, July 2014 13 3501 Wismann Lane, Quincy IL - 62305-3116

CONTROL GROUP 110847
(control version L)

Item Part
Number Qty. Number Description

1 1 110827-001 hydraulic unloader assembly

2 3 1642 tube fitting, 90° male elbow, 1/4 tube x 1/8 NPT
3 3ft. 110515-025 copper tube, 1/4 o.d.
4 1 1665 tube fitting, tee, 1/4 tube x 1/4 tube x 1/8 NPT

Maintenance Parts
1 113225 Hydraulic Unloader Repair Ki
includes diaphragm, stem assembly, inlet filter & fitting assembly, spring (0-200
PSIG) and spring (201-500 PSIG red color code, DO NOT USE RED SPRING
FOR MODEL 216)

Parts for use with diester or phosphate ester synthetic based lubricants
1 1 110827-003 hydraulic unloader assembly

QR 216 Quincy Compressor

2022203800, July 2014 14 3501 Wismann Lane, Quincy IL - 62305-3116

 CONTROL GROUP 2023903354
(control version LS)

* See page 17 for optional pilot valves that must be used with respective pressure ranges.

QR 216 Quincy Compressor

2022203800, July 2014 15 3501 Wismann Lane, Quincy IL - 62305-3116

CONTROL GROUP 2023903254
(control version LVD)

* See page 17 for optional pilot valves that must be used with respective pressure ranges.

QR 216 Quincy Compressor

2022203800, July 2014 16 3501 Wismann Lane, Quincy IL - 62305-3116

 PILOT VALVES

QR 216 Quincy Compressor

2022203800, July 2014 17 3501 Wismann Lane, Quincy IL - 62305-3116

SUCTION VALVE
UNLOADER ASSEMBLIES
Description Installation
The Quincy suction valve unloader assembly consists The pilot valve is to be connected to the air receiver
of unloading arrangements on the suction valves, using a minimum of 3/8" o.d. copper tube. Compres-
having a plunger to contact the suction valve disc sors in the field, not equipped with a suction valve
and an unloader pilot valve to automatically regulate unloader assembly, can be converted to constant speed.
the passing of receiver pressure to the unloading ar- Consult your local Quincy distributor for assistance
rangement. with conversion procedures.

Application Service
Suction valve unloader assemblies are recommended Periodically check the filter & screens in the inlet of
for use on Quincy compressors where the compressor the pilot valve to make sure they are free of obstruc-
is to run continuously and a constant pressure is to be tions. If they become clogged, remove and clean or
maintained. The purpose is to automatically unseat replace. Inspect the "o"ring located in the opposite end
the suction valve of the compressor when the air of the pilot valve body for wear or damage; replace if
supply is greater than the demand. necessary.

Operation Adjustment
Unloading occurs when receiver pressure is sufficient The unloading pressure is adjustable and is regulated
to overcome pilot valve spring pressure. The check by turning the hex nut (marked "unload adj." in cross
ball is then unseated, allowing receiver pressure to sectional illustrations of pilot valves). Turn the hex
pass to the unloading arrangements. The compressor nut clockwise to increase and counterclockwise to
will run unloaded until the receiver pressure drops decrease the unloading pressure.
to a predetermined level. At this time, the action of
the ball is reversed, shutting off receiver pressure to The differential (difference between unloading
the unloader arrangement and venting the unloader and loading pressure) is set by turning the hex nut
to atmosphere. This allows the compressor to load. marked "differential adjustment" in the illustrations
The drive, either electric motor or combustion engine, of the pilot valves on previous pages. Increase the dif-
runs continuously and must be started and stopped ferential pressure by turning the hex nut clockwise
manually. - decrease by turning counterclockwise. Tighten the
locknuts after adjustment.
The LS control version is equipped with a toggle
lever on the pilot valve which can be flipped to provide
manual unloading.

The LVD control version is designed to provide a

choice between "start/stop" or "continuous run" opera-
tion. The LVD pilot valve can be set for "start/stop"
operation by turning the knurled knob at the end of
the pilot valve clockwise until it stops. Under these
circumstances a pressure switch is required to stop
the motor. Failure to use a pressure switch, with the
pilot valve locked out, could result in unsafe conditions.

WARNING !
A pressure switch must be incorporated whenever an LVD
pilot valve is employed as part of the control system.

The compressor will operate in the continous run

mode if the knurled knob on the LVD pilot valve is
turned counterclockwise until it stops.

QR 216 Quincy Compressor

2022203800, July 2014 18 3501 Wismann Lane, Quincy IL - 62305-3116

 Head Kit K216F Gasket Set 5508
Item Part Item Part
# Qty. Number Description # Qty. Number Description
4 1552-002 valve disc
4 1554 valve gasket
2 1202 valve spring
4 1556 valve gasket
2 1368 valve spring
1 1594 gasket
4 1554 valve gasket
1 1598 gasket, inspection plate
4 1556 valve gasket
2 1832 shim, bearing adj., .005, steel
2 1855 diaphragm
2 1832A shim, bearing adj., .007, steel
1 1943 head gasket
1 1832B shim, bearing adj., .020, steel
6 1832C shim, bearing adj., .005, paper
2 1832D shim, bearing adj., .002 stl.
1 1943 head gasket
Yearly Maintenance Kit 110516-216 1 6274 bearing carrier gasket
Item Part
# Qty. Number Description

1 110822 oil pressure gauge

2 1553X11 replacement discharge valve
assy.
2 1855 diaphragm
2 4610X3 replacement suction valve assy.
1 5508 gasket set
2 6283 hydraulic unloader filter

Piston Pin Kit K216E

Item Part
# Qty. Number Description
2 110190-008 piston pin
2 6440SR connecting rod bushing
4 8648 retaining ring

2
Overhaul Kit K216G 1

Item Part
# Qty. Number Description 3
2 2824PR inserts (pair), con rod bearing
2 6452A ring set (standard) no color code
4 1552-002 valve disc Decals
1 5508 gasket set
2 1202 valve spring Item Part
2 1368 valve spring # Qty. Number Description
1 110377E075 air filter element
1 110610 "o"ring kit 1 1 110831 serial number & nameplate
2 1 127889-A decal, CAUTION!, MANUAL
3 1 127889-B decal, DANGER!,"Air from this...."

Recommended Spare Parts

Oil Pump Repair Kit 2022132203
Item Part
# Qty. Number Description Item Part
# Qty. Number Description
1 4610X3 replacement suction valve assy.
1 1553X11 replacement discharge valve
1 22749-152 "o"ring
assy.
1 22749-112 "o"ring
1 110822 pressure gauge
1 22749-011 "o"ring
1 2022132203 oil pump repair kit
1 160003 oil pump gerotor
1 5508 gasket set
1 160075-001 key
1 2023903290 control valve inlet filter
1 6285 retaining ring
1 2024200202 driveshaft

QR 216 Quincy Compressor

2022203800, July 2014 19 3501 Wismann Lane, Quincy IL - 62305-3116

 QUINCY COMPRESSOR
STANDARD TERMS AND CONDITIONS
LEGAL EFFECT: Except as expressly otherwise agreed to in writing by TITLE & LIEN RIGHTS: The equipment shall remain personal property,
an authorized representative of Seller, the following terms and conditions regardless of how affixed to any realty or structure. Until the price (including
shall apply to and form a part of this order and any additional and/or different any notes given therefore) of the equipment has been fully paid in cash, Seller
terms of Buyer’s purchase order or other form of acceptance are rejected in shall, in the event of Buyer’s default, have the right to repossess such equipment.
advance and shall not become a part of this order. PATENT INFRINGEMENT: If properly notified and given an opportunity
The rights of Buyer hereunder shall be neither assignable nor transferable to do so with friendly assistance, Seller will defend Buyer and the ultimate user
except with the written consent of Seller. of the equipment from any actual or alleged infringement of any published
This order may not be canceled or altered except with the written consent United States patent by the equipment or any part thereof furnished pursu-
of Seller and upon terms which will indemnify Seller against all loss oc- ant hereto (other than parts of special design, construction, or manufacture
casioned thereby. All additional costs incurred by Seller due to changes in specified by and originating with Buyer), and will pay all damages and costs
design or specifications, modification of this order or revision of product awarded by competent court in any suit thus defended or of which it may
must be paid for by Buyer. have had notice and opportunity to defend as aforesaid.
In addition to the rights and remedies conferred upon Seller by this order, STANDARD WARRANTY: Seller warrants that products of its own
Seller shall have all rights and remedies conferred at law and in equity and manufacture will be free from defects in workmanship and materials under
shall not be required to proceed with the performance of this order if Buyer normal use and service for the period specified in the product instruction
is in default in the performance of such order or of any other contract or manual. Warranty for service parts will be Ninety (90) days from date of
order with seller. factory shipment. Electric Motors, gasoline and diesel engines, electrical ap-
TERMS OF PAYMENT: Unless otherwise specified in the order acknowl- paratus and all other accessories, components and parts not manufactured by
edgment, the terms of payment shall be 1% 15, net forty-five (45) days after Seller are warranted only to the extent of the original manufacturer’s warranty.
shipment. These terms shall apply to partial as well as complete shipments. Notice of the alleged defect must be given to the Seller, in writing with
If any proceeding be initiated by or against Buyer under any bankruptcy or all identifying details including serial number, type of equipment and date
insolvency law, or in the judgment of Seller the financial condition of Buyer, of purchase within thirty (30) days of the discovery of the same during the
at the time the equipment is ready for shipment, does not justify the terms of warranty period.
payment specified, Seller reserves the right to require full payment in cash prior Seller’s sole obligation on this warranty shall be, at its option, to repair
to making shipment. If such payment is not received within fifteen (15) days or replace or refund the purchase price of any product or part thereof which
after notification of readiness for shipment, Seller may cancel the order as to proves to be defective. If requested by Seller, such product or part thereof
any unshipped item and require payment of its reasonable cancellation charges. must be promptly returned to seller, freight prepaid, for inspection.
If Buyer delays shipment, payments based on date of shipment shall become Seller warrants repaired or replaced parts of its own manufacture against
due as of the date when ready for shipment. If Buyer delays completion of defects in materials and workmanship under normal use and service for ninety
manufacture, Seller may elect to require payment according to percentage of (90) days or for the remainder of the warranty on the product being repaired.
completion. Equipment held for Buyer shall be at Buyer’s risk and storage This warranty shall not apply and Seller shall not be responsible or liable for:
charges may be applied at the discretion of Seller.
(a) Consequential, collateral or special losses or damages;
Accounts past due shall bare interest at the highest rate lawful to contract for
(b) Equipment conditions caused by fair wear and tear, abnormal condi-
but if there is no limit set by law, such interest shall be eighteen percent (18%).
tions of use, accident, neglect or misuse of equipment, improper storage or
Buyer shall pay all cost and expenses, including reasonable attorney’s fees,
damage resulting during shipping;
incurred in collecting the same, and no claim, except claims within Seller’s
warranty of material or workmanship, as stated below, will be recognized unless (c) Deviation from operating instructions, specifications or other special
delivered in writing to Seller within thirty (30) days after date of shipment. terms of sale;
TAXES: All prices exclude present and future sales, use, occupation, (d) Labor charges, loss or damage resulting from improper operation,
license, excise, and other taxes in respect of manufacture, sales or delivery, maintenance or repairs made by person(s) other than Seller or Seller’s au-
all of which shall be paid by Buyer unless included in the purchase price at thorized service station.
the proper rate or a proper exemption certificate is furnished. In no event shall Seller be liable for any claims whether arising from breach
ACCEPTANCE: All offers to purchase, quotations and contracts of sales of contract or warranty or claims of negligence or negligent manufacture in
are subject to final acceptance by an authorized representative at Seller’s plant. excess of the purchase price.
DELIVERY: Except as otherwise specified in this quotation, delivery will THIS WARRANTY IS THE SOLE WARRANTY OF SELLERS AND
be F. O. B. point of shipment. In the absence of exact shipping instruction, ANY OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED IN
Seller will use its discretion regarding best means of insured shipment. No LAW OR IMPLIED IN FACT, INCLUDING ANY WARRANTIES OF
liability will be accepted by Seller for so doing. All transportation charges MERCHANTABILITY AND FITNESS FOR PARTICULAR USE ARE
are at Buyer’s expense. Time of delivery is an estimate only and is based HEREBY SPECIFICALLY EXCLUDED.
upon the receipt of all information and necessary approvals. The shipping LIABILITY LIMITATIONS: Under no circumstances shall the Seller have
schedule shall not be construed to limit seller in making commitments for any liability for liquidated damages or for collateral, consequential or special
materials or in fabricating articles under this order in accordance with Seller’s damages or for loss of profits, or for actual losses or for loss of production or
normal and reasonable production schedules. progress of construction, whether resulting from delays in delivery or perfor-
Seller shall in no event be liable for delays caused by fires, acts of God, mance, breach of warranty, negligent manufacture or otherwise.
strikes, labor difficulties, acts of governmental or military authorities, delays ENVIRONMENTAL AND OSHA REQUIREMENTS: At the time of
in transportation or procuring materials, or causes of any kind beyond Seller’s shipment of the equipment from the factory, Quincy Compressor / Ortman
control. No provision for liquidated damages for any cause shall apply under Fluid Power will comply with the various Federal, State and local laws and
this order. Buyer shall accept delivery within thirty (30) days after receipt of regulations concerning occupational health and safety and pollution. How-
notification of readiness for shipment. Claims for shortages will be deemed ever, in the installation and operation of the equipment and other matters
to have been waived if not made in writing with ten (10) days after the receipt over which the seller has no control, the Seller assumes no responsibility for
of the material in respect of which any such shortage is claimed. Seller is compliance with those laws and regulations, whether by the way of indemnity,
not responsible for loss or damage in transit after having received “In Good warranty or otherwise.
Order” receipt from the carrier. All claims for loss or damage in transit should June 30, 2003
be made to the carrier.

QR 216 Quincy Compressor

2022203800, July 2014 20 3501 Wismann Lane, Quincy IL - 62305-3116

Reciprocating / Systems: 217.222.7700
E-mail: [email protected]
Website: quincycompressor.com