Adesivo 5181h Loctite
Adesivo 5181h Loctite
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: BONDS SKIN IN SECONDS.
COMBUSTIBLE LIQUID.
CAUSES SKIN AND EYE IRRITATION.
MAY CAUSE RESPIRATORY IRRITATION.
PICTOGRAM(S)
Precautionary Statements
Prevention:
Keep away from heat,sparks, open flames, hot surfaces - no smoking. Avoid breathing vapors,
mist, or spray. Wash thoroughly after handling. Use only outdoors or in a well-ventilated area.
Wear protective gloves, eye protection, and face protection.
Response:
IF ON SKIN: Wash with plenty of soap and water. IF INHALED: Remove person to fresh air and
keep comfortable for breathing.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if
present and easy to remove. Continue rinsing. Call a poison control center or physician if you
feel unwell. If skin irritation occurs: Get medical attention. If eye irritation persists: Get medical
attention. Take off contaminated clothing. In case of fire: Use foam, dry chemical or carbon
dioxide to extinguish.
Storage:
Store in a well-ventilated place. Keep container tightly closed. Store in a well-ventilated place.
Keep cool. Store locked up.
Disposal:
Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
* Exact percentage is a trade secret. Concentration range is provided to assist users in providing appropriate protections.
Skin contact: Do not pull bonded skin apart. Soak in warm soapy water. Gently peel apart
using a blunt instrument. If skin is burned due to the rapid generation of heat
by a large drop, seek medical attention. If lips are bonded, apply warm water
to the lips and encourage wetting and pressure from saliva in mouth. Peel or
roll lips apart. Do not pull lips apart with direct opposing force.
Eye contact: Immediately flush with plenty of water for at least 15 minutes. Get medical
attention. If eyelids are bonded closed, release eyelashes with warm water by
covering with a wet pad. Do not force eye open. Cyanoacrylate will bond to
eye protein and will cause a lachrymatory effect which will help to debond the
adhesive. Keep eye covered until debonding is complete, usually within 1-3
days. Medical attention should be sought in case solid particles of polymerized
cyanoacrylate trapped behind the eyelid caused abrasive damage.
Ingestion: Ensure breathing passages are not obstructed. The product will polymerize
rapidly and bond to the mouth making it almost impossible to swallow. Saliva
will separate any solidified product in several hours. Prevent the patient from
swallowing any separated mass.
Notes to physician: Surgery is not necessary to separate accidentally bonded tissues. Experience
has shown that bonded tissues are best treated by passive, non-surgical first
aid. If rapid curing has caused thermal burns they should be treated
symptomatically after adhesive is removed.
Special firefighting procedures: Wear a self-contained breathing apparatus with a full face piece operated in
pressure-demand or other positive pressure mode.
Environmental precautions: Ventilate area. Do not allow product to enter sewer or waterways.
Clean-up methods: Do not use cloths for mopping up. Flood with water to complete polymerization
and scrape off the floor. Cured material can be disposed of as non-hazardous
waste. Refer to Section 8 "Exposure Controls / Personal Protection" prior to
clean up.
Storage: Keep in a cool, well ventilated area away from heat, sparks and open flame.
Keep container tightly closed until ready for use.
For information on product shelf life contact Henkel Customer Service at (800) 243-4874.
Engineering controls: Use positive down-draft exhaust ventilation if general ventilation is insufficient
to maintain vapor concentration below established exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure
limit(s).
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists.
Skin protection: Use nitrile gloves and aprons as necessary to prevent contact. Do not use
PVC, nylon or cotton.
Hazardous reactions: Rapid exothermic polymerization will occur in the presence of water, amines, alkalis and
alcohols.
Inhalation: May cause respiratory tract irritation. Exposure to vapors above the established exposure limit
results in respiratory irritation, which may lead to difficulty in breathing and tightness in the
chest.
Skin contact: Causes skin irritation. Bonds skin in seconds. Cyanoacrylates have been reported to cause
allergic reaction but due to rapid polymerization at the skin surface, an allergic response is rare.
Cyanoacrylates generate heat on solidification. In rare circumstances a large drop will burn the
skin. Cured adhesive does not present a health hazard even if bonded to the skin.
Eye contact: Irritating to eyes. Causes excessive tearing. Eyelids may bond.
Ingestion: Not expected to be harmful by ingestion. Rapidly polymerizes (solidifies) and bonds in mouth. It
is almost impossible to swallow.
Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects
Ethyl 2-cyanoacrylate None Irritant, Allergen, Respiratory
Thickener None Irritant
Respiratory, Some evidence of
Carbon black Oral LD50 (RAT) = > 8,000 mg/kg
carcinogenicity
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Ethyl 2-cyanoacrylate No No No
Thickener No No No
Carbon black No Group 2B No
Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
TSCA 8 (b) Inventory Status: All components are listed or are exempt from listing on the Toxic Substances Control Act
Inventory.
TSCA 12 (b) Export Notification: None above reporting de minimis
California Proposition 65: This product contains a chemical known in the State of California to cause cancer. This
product contains a chemical known to the State of California to cause birth defects or other
reproductive harm.
CEPA DSL/NDSL Status: Contains one or more components listed on the Non-Domestic Substances List. All other
components are listed on or are exempt from listing on the Domestic Substances List.
Components listed on the NDSL must be tracked by all Canadian Importers of Record as
required by Environment Canada. They may be imported into Canada in limited quantities.
Please contact Regulatory Affairs for additional details.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.