Professional Documents
Culture Documents
High Voltage Engineering Assignment No 2: Ma'Am DR Sidra Mumtaz
High Voltage Engineering Assignment No 2: Ma'Am DR Sidra Mumtaz
ASSIGNMENT NO 2nd
MA’AM DR SIDRA MUMTAZ
PAGE 1
where
L — Residual inductance
C — Residual capacitance
For extended and large dimensioned resistors, this equivalent circuit is not valid and each
elemental resistor has to be approximated with this equivalent circuit. The entire resistor
unit then has to be taken as a transmission line equivalent, for calculating the effective
resistance. Also, the ground or stray capacitance of each element influences the current
flowing in the unit, and the indication of the meter results in an error.
The equivalent circuit of a high voltage resistor neglecting inductance and the circuit of
compensated series resistor using guard and tuning resistors is shown in Fig 7.9 a and b
respectively. Stray ground capacitance effects (refer Fig. 7.9b) can be removed by shielding
the resistor R by a second surrounding spiral Rs, which shunts the actual resistor but does
not contribute to the current through the instrument. By tuning the resistors Ra, the
shielding resistor and potentials may be adjusted with respect to the actual measuring
PAGE 2
resistor so that the resulting compensation currents between the shield and the measuring
resistors provide a minimum phase angle.
where
PAGE 3
SERIES CAPACITANCE VOLTMETER:
To avoid the drawbacks pointed out earlier, a Series Capacitance Voltmeter is used instead
of a resistor for a.c. high voltage measurements. The schematic diagram is shown in Fig.
7.10. The current Ic through the meter is:
where,
If the a.c. voltage contains harmonics, error due to changes in series impedance occurs.
The rms value of the voltage V with harmonics is given by
where V1,V2,…Vn represent the rms value of the fundamental, second … and nth
harmonics.
PAGE 4
Hence, the resultant rms currents is:
With a 10% fifth harmonic only, the current is 11.2% higher, and hence the error is 11.2%
in the voltage measurement.
This method is not recommended when a.c. voltages are not pure sinusoidal waves but
contain considerable harmonics.
Series capacitance voltmeters were used with cascade transformers for measuring rms
values up to 1000 kV. The series capacitance was formed as a parallel plate capacitor
between the high voltage terminal of the transformer and a ground plate suspended above
it. A rectifier ammeter was used as an indicating instrument and was directly calibrated in
high voltage rms value. The meter was usually a 0-100 μA moving coil meter and the over-
all error was about 2%.
CAPACITANCE POTENTIAL:
While electric potential measures the ability to perform work on a charge, capacitance
measures the ability to store charge. The unit of measurement for capacitance is Coulomb
per Voltage (C/V), which is the amount of charge present per voltage applied. The Farad
(F) is commonly used instead of C/V to measure capacitance. A capacitor is used to hold
capacitance and is created when two plates are parallel to each other, with each end
connected to opposite charge sources. Each charge fills one of the parallel plates generating
an electric field between the two. The capacitor can then discharge the charges between the
two plates when connected. The equation to determine the capacitance is:
C = e0 · k · A/d
Where C is the capacitance (F), e0 is the permittivity of free space (8.85 E -12 F/m), k is
the relative permittivity of the dielectric material between the plates, A is the geometric
area of both plates (m·m), and d is the distance between the two plates (m). The capacitance
is inversely proportional to the distance, so the greater the separation between the two
plates, the smaller the capacitance available. Additionally, the k-value is determined by the
material between the parallel plates and is directly proportional to the capacitance; most
capacitors have a solid in between the capacitor to improve capacitance.
PAGE 5
CAPACITANCE VOLTAGE TRANFORMER:
The capacitive voltage transformer step-down the high voltage input signals and provide
the low voltage signals which can easily measure through the measuring instrument. The
Capacitive voltage transformer (CVT) is also called capacitive potential transformer
The capacitive potential divider, inductive element and the auxiliary transformer are the
three main parts of the capacitive potential transformer. For measuring high voltage (above
100kV) the high insulated transformer is required. The highly insulated transformer is quite
expensive as compared to the normal transformer. For reducing the cost, the capacitive
potential transformer is used in the system. The CVT is cheap, and their performance is not
much inferior to the highly insulated transformer.
PAGE 6