Professional Documents
Culture Documents
Detroit Diesel ApplicationUser's Manual - Suite 8.3
Detroit Diesel ApplicationUser's Manual - Suite 8.3
com/
Detroit Diesel
Application
User’s Manual
https://truckmanualshub.com/
Chapter 1:
Using This Manual ................................................. 1
Manual Overview........................................................................... 2
Conventions................................................................................... 3
Special Messages................................................................................. 3
Notes ................................................................................................. 3
Important ........................................................................................... 3
Cautions ............................................................................................ 3
Warnings ........................................................................................... 3
Stop ................................................................................................... 4
Troubleshooting................................................................................. 4
Specialized Text ................................................................................... 5
Chapter 2:
Getting Started ..................................................... 7
Loading the Application ................................................................. 8
Making Selections ....................................................................... 10
Chapter 3:
Using the Engine Application ................................ 11
Accessing the Engine Application ............................................... 12
Viewing the Data List................................................................... 14
Viewing Diagnostic Codes........................................................... 15
View Active Codes.............................................................................. 16
View Inactive Codes ........................................................................... 17
Clear Codes........................................................................................ 19
Chapter 4:
Using the Marine Controls Application.................. 105
Accessing the DDEC Marine Controls Menu............................. 107
Viewing the Data List................................................................. 108
Viewing Diagnostic Codes......................................................... 110
View Active Codes ........................................................................... 110
View Codes Since Last Power Up.................................................... 112
View Historic Codes ......................................................................... 114
Viewing Calibrations .................................................................. 116
View Marine Controls Calibration ..................................................... 117
View Engine Calibration ................................................................... 118
View Marine Gear Actuator Calibration ............................................ 119
View Troll Calibration........................................................................ 120
Viewing Switch/Light Status ...................................................... 122
Viewing MIDS Received ............................................................ 124
Chapter 5:
Using the Series 638 Application......................... 127
Accessing the Application.......................................................... 129
Viewing the Data List................................................................. 131
Viewing/Clearing Defect Codes................................................. 133
Viewing Defect Codes ...................................................................... 133
Clearing Defect Codes ..................................................................... 134
Viewing I/O Status ..................................................................... 137
Appendix A:
Parameter Listings ............................................. 139
DDEC Engine Parameters ........................................................ 140
Locating a DDEC III/IV Parameter List ............................................. 140
Engine Data List ............................................................................... 142
Engine and Vehicle Configuration .................................................... 150
Idle Shutdown Configuration ............................................................ 155
VSG (Marine Throttle) Calibration .................................................... 156
Engine Protection Configuration....................................................... 157
Cruise Control Configuration ............................................................ 158
Progressive Shift Configuration ........................................................ 160
ECM Input/Output Configuration ...................................................... 162
Air Compressor Configuration .......................................................... 164
Function Lockout Configuration........................................................ 164
Injector Calibration ........................................................................... 167
Total Engine Data............................................................................. 167
Engine Trip Data .............................................................................. 168
Idle Shutdown Calibration ................................................................ 170
VSG (Marine Throttle) Reprogrammable Calibration ....................... 171
Engine Protection Calibration........................................................... 172
Cruise Control Calibration ................................................................ 174
Progressive Shift Calibration ............................................................ 177
Engine Droop Options ...................................................................... 179
Engine and Vehicle Options ............................................................. 179
Engine Rating Calibration................................................................. 181
Air Compressor Calibration .............................................................. 183
Transmission Calibration .................................................................. 183
Top 2 Transmission .......................................................................... 184
Maintenance Alert System Calibration ............................................. 185
ECM Input Switches ......................................................................... 186
ECM Output Status .......................................................................... 187
Activate ECM Output........................................................................ 189
Transmission Configuration.............................................................. 191
Performance Data ............................................................................ 191
Transmission Trip Data .................................................................... 192
Maintenance Alert System ............................................................... 193
Appendix B:
Warranty & Service ............................................ 217
Exclusive Warranty.................................................................... 218
Exclusive Remedy ..................................................................... 219
Return Materials Authorization (RMA)....................................... 220
Return of Goods Policy.............................................................. 222
Return Goods Authorization (RGA) Procedure ................................ 223
Index............................................................... 225
T his chapter provides an overview of this manual’s organization and the conventions
used throughout.
Manual Overview
This manual provides basic and detailed information to support you in using the
Pro-Link® tool.
• Table of Contents—helps you to find the information you are looking for
quickly and easily.
• Using this Manual—provides an overview of this user’s manual.
• Getting Started—provides instructions on loading the application.
• Using the Engine Application—provides detailed instructions for access-
ing and using each of the application’s menu options.
• Using the Marine Application—provides detailed instructions for access-
ing and using each of the application’s menu options.
• Using the Series 638 Application—provides detailed instructions for ac-
cessing and using each of the application’s menu options.
• Parameter Listings (Appendix)—provides a comprehensive listing of all
supported parameters with descriptions for each.
• Warranty & Service (Appendix)—provides warranty and service
information.
• Index—provides an alphabetical listing of all major topics covered in this
user’s manual.
Each chapter is introduced by an “at-a-glance” list of the chapter’s contents, along
with corresponding page numbers.
Conventions
Conventions
Different conventions are used in this user’s manual to draw your attention to
certain types of information. This section provides an overview of these
conventions.
Special Messages
Notes
NOTE provides explanations, comments, or tips related to the subject matter that
is being discussed.
Example:
NOTE:
i Refer to the page number provided for each described component for fur-
ther details.
Important
IMPORTANT indicates a situation which, if not avoided, may result in damage to
the test equipment or vehicle.
Example:
IMPORTANT:
Example:
CAUTION:
Example:
WARNING:
ä Wear gloves when handling hot engine components.
Stop
Information that needs to be considered before proceeding is presented in the fol-
lowing manner:
Troubleshooting
Information intended to help you to address or anticipate potential issues are pre-
sented in the following manner:
Conventions
Specialized Text
The following specially formatted text is used to help you to differentiate certain
elements discussed within this manual:
Getting Started
The Detroit Diesel Application consists of three applications specific to the following
engine types:
This chapter provides instructions on loading the application and navigating through its
menu hierarchy.
NOTE:
i Since this application is supported® by both the Pro-Link GRAPHIQ™ and the Pro-Link®
Plus, this manual uses “Pro-Link ” to refer to both products.
Use the following procedure to load the Detroit Diesel Application onto the
Pro-Link®.
1 Be sure that the Detroit Diesel Application is properly loaded on the Pro-Link®.
Once the application is loaded, the screen displays the DDC Suite main
menu.
↑- - - - S e l e c t ions---- ↓
DDEC III/IV xx.x
2 Press to select the DDEC III/IV. The screen indicates that the selected
application is loading, then displays a safety message.
LOADING
“DDEC III/IV xx.x”
PLEASE WAIT...
Once the application is loaded, the screen displays the DDEC III/IV menu.
DDEC III/IV
↑----Selections---- ↓
ENGINE MENU
Once you load the DDEC III/IV application, you have access to the following menu
options:
Making Selections
In order to use the features provided with this application, you will need to select
from various menus presented on the Pro-Link® screen. Making selections typi-
cally involves using the arrow keys navigate to a desired option, then pressing the
key.
The following convention is used throughout this manual in order to provide ab-
breviated instructions on making on-screen selections.
1 From the DDEC III/IV Main Menu, press the or key to select
Engine Menu, then press .
T his chapter provides instructions on accessing and using the Engine Application
features.
2 Once the application boots up, access the DDEC III/IV menu.
DDEC III/IV
↑- - - - S e l e c t ions---- ↓
ENGINE MENU
The screen displays the engine type and series number. For example:
DDEC IV
SERIES 60
[ENTER] TO CONTINUE
NOTE:
i The screen will display according to the ECM that is currently communicat-
®
ing with the Pro-Link .
ENGINE MENU
↑----Selections---- ↓
DATA LIST
NOTE:
i See “Engine Data List”, on page 142 for a complete list of all engine data
list parameters and possible values for each.
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
The screen indicates that data is being requested, then displays the data
list. For example:
ACTIVE CODES Y ES
INACTIVE CODES NO
ENGINE RPM 0rpm
PULSEWIDTH 0.00°
2 Press the or key to scroll through the data list items, as needed.
Use the Active Codes and Inactive Codes options to view occurrence information for
active or inactive diagnostic codes. The screen displays the fault.
63 MID:128 ENGINE
PWM DRIVER #2
OPEN CIRCUIT
A 1 SID: 58 FMI: 4 ↓
1st:2 Last:0
# : 1 T o t a l T im e : 6 5 5 3 5
Log:07/08 09:39 GMT
Max: 60.00
* GMT (Greenwich Mean Time) displays for ECM software version 20.0 or greater.
DIAGNOSTIC CODES
↑----Selections---- ↓
ACTIVE CODES
2 Press to select Active Codes. The screen indicates that the codes are
being retrieved, then displays the codes. For example:
31 MID:128 ENGINE
AUXILIARY OUTPUT #4
OPEN CIRCUIT
A 1 SID: 52 FMI: 3 ↓
—If no codes are detected, the screen indicates, “No Active Codes”. In this
instance, press to exit the screen.
3 Press the or key to scroll through the data, as needed.
1st:2 Last:0
# : 1 T o t a l T im e : 6 5 5 3 5
Log:07/08 09:39 GMT
Min:1.50
NOTE:
i See Figure 3.1, on page 16 for descriptions of each line item on the
screen.
4 Press to return to the active code list screen and select another active
code to view, if desired.
DIAGNOSTIC CODES
↑----Selections---- ↓
INACTIVE CODES
The screen indicates that the codes are being retrieved, then displays the
data screen. For example:
33 MID:128 ENGINE
TURBO BOOST SENSOR
INPUT VOLTAGE HIGH
I 1 PID:102 FMI: 3 ↓
—If no codes are detected, the screen indicates, “No Inactive Codes”. In this
instance, press to exit the screen.
3 Press the or key to scroll through the data, as needed.
1st:2 Last:2
# : 4 T o t a l T im e : 5 5 5 5 9
Log:07/12 17:17 GMT
Min:1.50
NOTE:
i See Figure 3.1, on page 16 for descriptions of each line item on the
screen.
4 Press to return to the inactive code screen and select another inactive
code to view, if desired.
Clear Codes
To clear inactive codes from ECM memory:
1 From the Engine Menu screen, select DIAGNOSTIC CODES. The screen
displays the Diagnostic Codes menu.
DIAGNOSTIC CODES
↑- - - - S e l e c t ions---- ↓
CLEAR CODES
The screen displays a message indicating that the data is being requested,
then displays the data. For example:
3 Select Yes. The screen indicates that the codes are being cleared.
CLEARING FAULT
CODES
PLEASE WAIT...
Once the codes are cleared, the screen returns to the Diagnostic Codes
menu.
DIAGNOSTIC CODES
↑----Selections---- ↓
CLEAR CODES
NOTE:
i Pro-Link® displays the temperature readings in “firing order”.
NOTE:
i Only the number of cylinders connected to the engine will be displayed (up
to 16).
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
EXHAUST TMP MONITOR
Viewing Calibrations
Viewing Calibrations
Use the View Calibrations feature to view the engine and vehicle operating param-
eters that are stored in the DDEC III/IV Electrically Erasable Programmable Read
Only Memory (EEPROM).
NOTE:
i See “Engine and Vehicle Configuration”, on page 150 for a list of all avail-
able engine configuration parameters.
ENGINE MENU
↑----Selections---- ↓
VIEW CALIBRATIONS
VIEW CALIBRATIONS
↑- - - - S e l e c t ions---- ↓
ENGINE CONFIG
The screen displays a message indicating that the data is being requested,
then displays the idle shutdown data. For example:
Viewing Calibrations
NOTE:
i See “Idle Shutdown Configuration”, on page 155 for a list of all available
idle shutdown configuration parameters.
ENGINE MENU
↑----Selections---- ↓
VIEW CALIBRATIONS
VIEW CALIBRATIONS
↑----Selections---- ↓
IDLE SHUTDOWN
The screen displays a message indicating that the data is being requested,
then displays the idle shutdown data. For example:
ENABLED YES
TIME 60MIN
OVERRIDE YES
AUTO OVERRIDE Y ES
Viewing Calibrations
NOTE:
i You can use the Change Menu Description feature to switch between viewing
VSG or Throttle calibration settings. See “Changing Description Options”,
on page 59 for details.
NOTE:
i Refer to “VSG (Marine Throttle) Calibration”, on page 156 for a list of all
VSG (Throttle) calibration parameters.
ENGINE MENU
↑----Selections---- ↓
VIEW CALIBRATIONS
VIEW CALIBRATIONS
↑- - - - S e l e c t ions---- ↓
VSG CALIBRATION
The screen displays a message indicating that the data is being requested,
then displays the data. For example:
Viewing Calibrations
Please keep the following in mind when viewing Engine Protection data on the
Pro-Link® screen:
• Parameter values that are displayed as “N/A” indicates that the sensor
and/or function are not part of the engine configuration.
• The R1 designation indicates that the value displayed is being transmit-
ted from the engine receiver ECM #1
• The R2 designation indicates that the value displayed is being transmit-
ted from the engine receiver ECM #2
NOTE:
i See “Engine Protection Configuration”, on page 157 for a list of all Engine
Protection parameters.
ENGINE MENU
↑----Selections---- ↓
VIEW CALIBRATIONS
VIEW CALIBRATIONS
↑- - - - S e l e c t ions---- ↓
ENGINE PROTECT
The system briefly displays a message indicating that the data is being
requested.
Viewing Calibrations
NOTE:
i See “Cruise Control Configuration”, on page 158 for a list of all cruise con-
trol parameters and their corresponding values.
ENGINE MENU
↑----Selections---- ↓
VIEW CALIBRATIONS
VIEW CALIBRATIONS
↑----Selections---- ↓
CRUISE CONTROL
The system briefly displays a message indicating that the data is being
requested.
Viewing Calibrations
NOTE:
i This feature is only available if the vehicle is equipped with a vehicle speed
sensor (VSS).
NOTE:
i See “Progressive Shift Configuration”, on page 160 for a list of all progres-
sive shift parameters and their corresponding values.
ENGINE MENU
↑----Selections---- ↓
VIEW CALIBRATIONS
VIEW CALIBRATIONS
↑----Selections---- ↓
PROGRESS SHIFT
The system briefly displays a message indicating that the data is being
requested.
ENABLED YES
LG#1 OFF SPD 19 Kph
LG#1 RPM LMT 1400rpm
LG#1 MAX LMT 1800rpm
Viewing Calibrations
Use the ECM INs/OUTs option to view ECM Input and Output Configuration informa-
tion that is currently programmed in the DDEC III/IV calibration, via the Pro-Link® .
Please keep the following in mind when viewing the ECM Input/Output data on the
Pro-Link® screen:
NOTE:
i See “ECM Input/Output Configuration”, on page 162 for a list of all ECM
Input/Output parameters.
NOTE:
i For Multi-ECM Engines, there will be a separate menu for R1 (MID 175)
and R2 (MID 183).
ENGINE MENU
↑----Selections---- ↓
VIEW CALIBRATIONS
VIEW CALIBRATIONS
↑- - - - S e l e c t ions---- ↓
ECM INs/OUTs
ECM INs/OUTs
↑- - - - S e l e c t ions---- ↓
MID:128 ECM
3 Press . The system briefly displays a message indicating that the data
is being requested. Then the system displays the data. For example:
Viewing Calibrations
NOTE:
i See “Air Compressor Configuration”, on page 164 for a list of all air com-
pressor parameters.
VIEW CALIBRATIONS
↑----Selections---- ↓
AIR COMPRESSOR
L OA D 20 ps i
U NL OA D 25 ps i
MAX RAT# 135psi
MIN RAT#1 60psi
If the air compressor function is not enabled on the ECM, the screen
displays a message indicating, “Air Compressor Not Available”. Press
to exit the screen.
NOTE:
i See “Function Lockout Configuration”, on page 164 for a list of function
lockout parameters that is available to view.
VIEW CALIBRATIONS
↑- - - - S e l e c t ions---- ↓
FUNCTION LOCKOUT
Viewing Calibrations
The screen displays a message indicating that the data is being requested,
then displays the data. For example:
IDLE SHUTDOWN NO
VSG CALIBRATION NO
ENGINE PROTECT NO
CRUISE CONTROL NO
Use the following procedure to access the Fuel Injector Info menu.
↑- - - - S e l e c t ions---- ↓
CYLINDER CUTOUT
Automatic Test
When running a test in automatic mode, the Pro-Link® controls the entire test and
displays the results as they occur.
First, the engine is allowed to run with all injectors operating. The resulting injector
pulse width is recorded on the first line. The bottom line contains the engine RPM.
After establishing the base pulse width, the Pro-Link® cuts out each injector in
turn. The pulse width that results for each cylinder is displayed. This process
repeats until all injectors have been cut out.
NOTE:
i Once the test has completed,
®
you can print out the results by pressing the
key on the Pro-Link , while viewing the results.
↑- - - - S e l e c t ions---- ↓
CYLINDER CUTOUT
DO YOU WISH TO
RUN A NEW TEST OR
REVIEW TEST RESULTS?
[NEWTEST] REVIEW
3 Select NEWTEST. The screen prompts you to select IDLE or the rpm setting.
SELECT RP M S E T T I N G
FOR CCO TEST NORMAL
(IDLE) OR 1000RPM
[IDLE] 1000RPM
[AUTO] MANUAL
USE ¦Ø TO REVIEW
AUTOMATIC TEST WHEN
COMPLETE
[ENTER TO CONTINUE]
NO CUTOUTPW = 2.8
2 C U TO UT PW = 4. 1
4 C U TO UT PW = 3. 9
END OF TEST ¦Ø TO VIEW
NOTE:
i The RPM displays on the last line of the screen until the test completes.
8 Press to exit the screen and return to the FUEL INJECTOR INFO
menu.
Manual Test
Running a manual test is similar to running an automatic test, except that you
choose the cylinder(s) to be cut out, rather than the Pro-Link® cutting out each
cylinder in-turn.
NOTE:
i Once the test has completed, you can print out the results by pressing the
®
key on the Pro-Link , while viewing the results.
↑- - - - S e l e c t ions---- ↓
CYLINDER CUTOUT
DO YOU WISH TO
RUN A NEW TEST OR
REVIEW TEST RESULTS?
[NEWTEST] REVIEW
—If you select RPM, the screen displays the following caution. (Press
when prompted, in order to view the entire message.)
IN PARK OR NEUTRAL
WITH PARKING BRAKE
APPLIED
[ENTER TO CONTINUE]
[AUTO] MANUAL
[AUTO] MANUAL
U S E ↔ TO CHANGE
CYL. USE ENTER
TO TURN CYL OFF.
[ENTER TO CONTINUE]
I N J 5 = O N ↔=N E X T
NO CUTOUT PW = 0.0
5 CUTOUT PW = 10.2
ENGINE RPM 0rpm
↑- - - - S e l e c t ions---- ↓
CYLINDER CUTOUT
DO YOU WISH TO
RUN A NEW TEST OR
REVIEW TEST RESULTS?
[NEWTEST] REVIEW
3 Select Review. The screen displays the test results. For example:
NO CUTOUTPW = 2.8
2 CU TO UT P W = 4 .1
4 CU TO UT P W = 3 .9
END OF TEST ↑↓ TO VIEW
—If no test results are available, the screen displays the following message:
CYLINDER CUTOUT
TEST RESULTS
NOT AVAILABLE
[ENTER] TO CONTINUE
Press .
NOTE:
i Fuel injector response times do not appear in the standard data list. You
must use this function to view them.
↑----Selections---- ↓
CYLINDER CUTOUT
2 Select RESPONSE TIMES. The screen displays a message indicating that the
data is being requested, then displays the data. For example:
INJECTOR 1 1.01 ms
INJECTOR 5 1.06 ms
INJECTOR 3 1. 1 7 ms
INJECTOR 6 1. 1 1 ms
NOTE:
i See “Injector Calibration”, on page 167 for a list of the calibrations for all
cylinders.
↑- - - - S e l e c t ions---- ↓
CYLINDER CUTOUT
2 Select CAL UPDATE. The screen displays the Cal Update menu.
CAL UPDATE
↑----Selections---- ↓
VIEW
CYL # 1 CAL 60
CYL # 5 CAL 58
CYL # 3 CAL 45
CYL # 6 CAL 52
↑- - - - S e l e c t ions---- ↓
CYLINDER CUTOUT
2 Select CAL UPDATE. The screen displays the Cal Update menu.
CAL UPDATE
↑- - - - S e l e c t ions---- ↓
VIEW
3 Select UPDATE. The screen displays a message indicating that the data is
being requested, then prompts you to enter the current password.
ENTER CURRENT
INJECTOR CAL CODE
PASSWORD
____
NOTE:
i If you need to re-enter a digit, simply press or to move to the
digit, then enter the correct digit.
The screen indicates that the password is being verified, then displays the
calibration data. For example:
CYL# 2R CAL 6
CYL# 3L CAL 5
CYL# 3R CAL 4
CYL# 1L CAL 3
—If the password you entered is not valid, the screen displays the following
message:
INVALID PASSWORD
[ENTER] TO CONTINUE
The screen prompts you to enter the new CAL Code. For example:
45
6 Press the numeric keys on the Pro-Link® keypad to enter the new calibration,
then press .
—If you want to update calibration for another cylinder, repeat Steps 4-5.
7 Press once you are finished entering new cylinder calibration values.
The screen displays the following message:
[CONTINUE] CANCEL
—If you do not want to continue with reprogramming the injector calibration,
select CANCEL, then press .
U P D A T I N G E CM M I D 1 2 8
P L E A S E W A I T A MINUTE
REPROGRAMMING ECM
MID: 128
SUCCESS
[ENTER to continue]
Changing Passwords
Use the Change Password option to change the password used for reprogramming
the injector calibration.
NOTE:
i The password you choose can be the same as, or different than, the pass-
words for change calibration and change engine rating.
↑- - - - S e l e c t ions---- ↓
CYLINDER CUTOUT
2 Select CHANGE PASSWORD. The the screen displays the following menu:
NOTE:
i Be sure that the engine is not running and the ignition is turned to the ON
position before selecting CONTINUE.
ENTER CURRENT
INJECTOR C A L C O D E
PASSWORD
____
5 Press .
____
—If you need to re-enter a digit, simply press the or key to move
to the digit, then enter the correct digit.
7 Press .
The screen indicates that the ECM is being reprogrammed. For example:
REPROGRAMMING ECM
MID: 128
SUCCESS
[ENTER to continue]
The password you entered is not valid, the screen re-displays the following
message:
____
NOTE:
i If you are unsuccessful in entering a valid password three times, you must
cycle the ignition key OFF, then back ON in order to attempt to enter the
password again.
NOTE:
i This option supports the Series 2000 and Series 4000 engines only and is
not available on other engines. The factory setting for this option is “USA”.
NOTE:
i The selected option will not take effect until the Pro-Link® is powered
down and powered back up. Once the selected option has taken effect, it
will remain in effect until it is changed.
↑----Selections---- ↓
CYLINDER CUTOUT
—If your engine type is not a Series 2000 or Series 4000, the screen displays
the following message:
ISO DESCRIPTIONS
ONLY AVAILABLE FOR
S2000/S4000
[ E N T E R ] T O CONTINUE
NOTE:
i See “Total Engine Data”, on page 167 or “Engine Trip Data”, on page 168
for a list of all available engine/trip data parameters.
ENGINE MENU
↑----Selections---- ↓
DATA LIST
SELECT TO VIEW
TOTAL OR TRIP INFO
TOTAL [TRIP]
3 Select TOTAL. The screen displays a message indicating that the data is being
requested, then displays the total engine data. For example:
FUEL 18.0L
HOURS 2.2 HRS
ODO 0.2km
I DL E 2. 1 H RS
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
SELECT TO VIEW
TOTAL OR TRIP INFO
TOTAL [TRIP]
3 Select TRIP. The screen prompts you to indicate whether you want to view the
data or reset the data parameters.
[VIEW] RESET
4 Select VIEW. The screen indicates that the data is being requested, then
displays the data, for example:
FUEL 18.0L
HOURS 2.2 HRS
FUEL L/H 0.0LPH
ODO 0.2km
NOTE:
i See “Engine Trip Data”, on page 168 for a list of all available parameters.
6 Press to exit; press again to return to the Engine Menu.
NOTE:
i Using the Reset option resets all trip data to “0.0”
1 Be sure that the Engine Menu screen is displaying.
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
SELECT TO VIEW
TOTAL OR TRIP INFO
TOTAL [TRIP]
3 Press to select TRIP. The screen prompts you to indicate whether you
want to view or reset the data parameters.
[VIEW] RESET
4 Select RESET. The screen prompts you to confirm that you want to reset the
trip data.
The screen indicates that the trip miles are being cleared.
Once the trip miles and fuel information are cleared, the screen returns to
the Engine Menu.
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
ENGINE/TRIP DATA
Changing Calibrations
Changing Calibrations
Use the Calibration Change feature to change engine and vehicle operation param-
eters that are stored in the DDEC III/IV EEPROM.
ENGINE MENU
↑----Selections---- ↓
DATA LIST
CALIBRATION CHANGE
↑----Selections---- ↓
REPROGRAM CAL
Reprogramming Calibrations
Use the Reprogram Cal option to reprogram calibrations.
NOTE:
i Be sure that the engine is OFF and the ignition key is turned to the ON
position.
The Reprogram Cal menu provides the following reprogram calibration options:
NOTE:
i See VSG (Marine Throttle) Reprogrammable Calibration (page 171) for
lists of parameters available to be reprogrammed for each calibration
option.
CALIBRATION CHANGE
↑- - - - S e l e c t ions---- ↓
REPROGRAM CAL
Changing Calibrations
3 The screen displays a message indicating that the data is being requested,
then prompts you to enter the current password.
ENTER CURRENT
PASSWORD
____
NOTE:
i If you need to re-enter a digit, simply press the or key to move
to the digit, then enter the correct digit.
5 Press .
6 Wait for the password to be verified. Once it is verified, the screen displays the
REPROGRAM CAL menu.
REPROGRAM CAL
↑----Selections---- ↓
IDLE SHUTDOWN
USE ↑↓ T O S E L E C T
PARM, USE ENTER TO
CHANGE VALUE.
[ENTER] TO CONTINUE
ENABLED Y ES
T IM E 5m in
O VE RR ID E Y ES
AUTO OVERR NOT EQUIP
10 Select the calibration parameter that you want to change. The screen prompts
you to enter the new value. For example, the following screen shows a new
value for the TIME parameter:
16
Changing Calibrations
11 Use the Pro-Link® keypad to enter the new calibration value, as follows:
—If you want to enter a new value for another calibration, repeat Steps 7 - 9.
13 Press .
SELECT ANOTHER
REPROG CAL
MENU?
YES [NO]
YES [NO]
PROGRAMMING ECM
[ ]
PLEASE WAIT...
Once the ECM is reprogrammed, the screen indicates that the reprogram-
ming was successful.
REPROGRAMMING ECM
MID: 128
SUCCESSFUL
[ENTER] TO CONTINUE
CALIBRATION CHANGE
↑- - - - S e l e c t ions---- ↓
REPROGRAM CAL
Changing Calibrations
CALIBRATION CHANGE
↑----Selections---- ↓
REPROGRAM CAL
2 Select VIEW HISTORY. The screen displays a message indicating that the data
is being requested, then displays the calibration history data. For example:
MID:128 ECM
LAST UPDATE: 2 HR S
TOOL ID: M1234567
# OF CHANGES: 34
3 Press when finished viewing the data; press again to return to the
Engine Menu.
CALIBRATION CHANGE
↑- - - - S e l e c t ions---- ↓
REPROGRAM CAL
Changing Calibrations
ENTER CURRENT
PASSWORD
____
____
—If the password you entered is not valid, the screen displays as follows:
INVALID PASSWORD
[ENTER] TO CONTINUE
Changing Calibrations
REPROGRAMMING ECM
MID: 128
SUCCESS
ENTER to continue
8 Press .
NOTE:
i The connector cavity designations describe the physical locations of the
switches and lights.
NOTE:
i See “ECM Input Switches”, on page 186 for a list of all ECM input parame-
ters or “ECM Output Status”, on page 187 for a list of all ECM output
parameters.
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
SWITCH/LIGHT STATS
↑----Selections---- ↓
MID:128 ECM
3 Select the desired option. The screen displays a message indicating that the
data is being requested, then displays the data. For example:
NOTE:
i Pro-Link® identifies the assigned functions by cavity number and descrip-
tion. The status of the functions read as “GND”, “OPN”, “BAT”, or “N/A”.
Activating Outputs
Use the Activate Outputs feature to activate ECM outputs via the Pro-Link® keypad.
When this option is selected, the screen displays the connector cavity and de-
scribes the function. The connector cavity designations describe the physical
locations to which the functions are assigned.
NOTE:
i If the connector cavity does not have a function assigned to it, “N/A” will
display.
NOTE:
i See “Activate ECM Output”, on page 189 for a list of all cavity functions.
To activate outputs:
1 Be sure that the Engine Menu screen is displaying.
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
Activating Outputs
ACTIVATE OUTPUTS
↑----Selections---- ↓
MID:128 ECM
3 Select the desired menu option. The screen displays the following messages:
REQUESTING DATA
PLEASE WAIT
ONE MINUTE...
↔ TO CHANGE STATUS
ENTER TO CHANGE
NUMBER
[ENTER TO CONTINUE]
MID:128 ECM
CHECK ENG LT GND
STOP ENG LT GND
F3 VEH PWR DO WN GND
6 Press the appropriate numeric key(s) on the Pro-Link® keypad, then press
. The screen returns to the data display.
ENGINE MENU
↑----Selections---- ↓
DATA LIST
2 Select MIDS RECEIVED. The screen displays each device that is sending out a
MID. For example:
ENGINE
MID 128
Resetting Components
Use the Reset Components feature to reset the engine component life function.
NOTE:
i In order to perform the engine component life function, the vehicle must be
equipped with the Detroit Diesel Hub system.
NOTE:
i This feature works with only DDEC III systems. It does not work with
DDEC IV systems.
• Oil Filter
• Air Filter
• Fuel Filter
• Oil
• Coolant Inhibitor
NOTE:
i Be sure that the engine is turned OFF and the ignition key is turned to the
ON position before starting this procedure.
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
Resetting Components
RESET COMPONENTS
↑----Selections---- ↓
OIL FILTER
3 Press the or key to scroll to the name of the component that you
want to reset, then press . The screen prompts you to confirm that you
want to reset the selected component. For example:
4 Select CONTINUE. The component life resets and the screen returns to the
Reset Components menu.
RESET COMPONENTS
↑- - - - S e l e c t ions---- ↓
OIL FILTER
Transmissions
Transmissions
Use the Transmissions feature to view information for the following transmission
types:
• ESS Transmission
• Top 2 Transmission
NOTE:
i Access to these menu options will be denied if the ECM is not configured
for the correct transmission types.
ENGINE MENU
↑----Selections---- ↓
DATA LIST
TRANSMISSIONS
↑----Selections---- ↓
ESS TRANSMISSION
Configuration
NOTE:
i See “Transmission Configuration”, on page 191 for a list of all parameters
that may be reprogrammed.
TRANSMISSIONS
↑- - - - S e l e c t ions---- ↓
ESS TRANSMISSION
2 Select the ESS Transmission option. The screen displays the ESS Transmis-
sion menu.
ESS TRANSMISSIONS
↑- - - - S e l e c t ions---- ↓
CONFIGURATION
Transmissions
3 Select Configuration. The screen displays a message indicating that the data
is being requested, then displays the data. For example:
TRANS MANUAL
LATE CHANGE NO
SECOND CHANCE NO
E N G B R A K E S H I FT NO
5 Press when finished viewing the data. The screen displays the ESS
Transmission menu
ESS TRANSMISSIONS
↑----Selections---- ↓
CONFIGURATION
Performance Data
NOTE:
i See “Performance Data”, on page 191 for a list of all parameters that may
be reprogrammed using the Performance Data option.
TRANSMISSIONS
↑- - - - S e l e c t ions---- ↓
ESS TRANSMISSION
ESS TRANSMISSIONS
↑- - - - S e l e c t ions---- ↓
CONFIGURATION
Transmissions
3 Select Performance Data. The screen displays a message indicating that the
data is being requested, then displays the data. For example:
Trip Data
NOTE:
i ESS Trip Data is reset when Engine Trip Data is reset.
NOTE:
i See “Transmission Trip Data”, on page 192 for a list of all parameters that
may be reprogrammed using the Trip Data option.
TRANSMISSIONS
↑----Selections---- ↓
ESS TRANSMISSION
2 Select the ESS Transmission option. The screen displays the ESS Transmis-
sion menu.
ESS TRANSMISSIONS
↑- - - - S e l e c t ions---- ↓
CONFIGURATION
3 Select Trip Data. The screen prompts you to indicate whether you want to view
the data or reset the data.
[VIEW] RESET
Transmissions
6 Press when finished viewing the data. The screen returns to the ESS
Transmission menu.
NOTE:
i This option requires ECM software versions release 8, or release 21 and
higher.
NOTE:
i Refer to “Reprogramming Calibrations”, on page 68 for instructions on
reprogramming the cruise master switch.
TRANSMISSIONS
↑----Selections---- ↓
ESS TRANSMISSION
TOP2 CRUISE SW ON
—If the Top 2 Transmission type is not available, the following message
displays:
TOP2 TRANSMISSIONS
UNAVAILABLE
[ENTER] TO CONTINUE
ENGINE MENU
↑----Selections---- ↓
DATA LIST
2 Select RESET AFR TABLE. The screen indicates that the AFR Learn Table is
being reset.
RESETTING
AFR LEARN TABLE
—If the engine is not a natural gas engine, the following message displays:
[ENTER] TO CONTINUE
—If the AFR reset is successful, the screen displays the following message:
AFR TABLE
S U C C E S S F U L LY R E S E T
[ENTER] TO CONTINUE
—If the AFR reset is not successful, the screen displays the following
message:
[ENTER] TO CONTINUE
NOTE:
i See “Maintenance Alert System Calibration”, on page 185 for a description
of each of the maintenance status parameters.
ENGINE MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
2 Select MAINT ALERT SYSTEM. The screen displays the Maint Alert System
menu.
↑----Selections---- ↓
MAINTENANCE STATUS
3 Select the Maintenance Status option. The screen displays the maintenance
information. For example:
5 Press when finished viewing the data. The screen returns to the Maint
Alert System menu.
↑- - - - S e l e c t ions---- ↓
MAINTENANCE STATUS
ONLY MAINTENANCE
ALERT SYSTEM CODES
WILL BE CLEARED
[ENTER] TO CONTINUE
3 Press . The screen indicates that the maintenance codes are being
cleared.
C L E A R I N G M AINTENANCE
CODES...
MAINTENANCE CODES
CLEARED
[ENTER] TO CONTINUE
↑----Selections---- ↓
CLEAR MAINT CODES
PTF Reset
Use the PTF Reset feature to reset the mileage after each PTF (Particulate Trap
Filer) cleaning.
The screen displays the mileage at which the PTF was last reset (or
“Unknown” if Page 2 Data is disabled).
2 Select YES to proceed with resetting the PTF. The screen indicates that the
PTF has been reset.
PTF RESET
[ENTER] TO CONTINUE
NOTE:
i Mileage is displayed in either English or metric units depending on the cur-
rent configuration. See page 104 for details.
ENGINE MENU
↑----Selections---- ↓
DATA LIST
2 Press the key to select Change Menu Desc, then press . The
screen displays as follows:
SELECT DESCRIPTIONS
MARINE [S T A N D A R D ]
Selecting English/Metric
Use the English/Metric feature to switch parameter and menu descriptions between
English and Metric.
CURRENT SETTING IS
METRIC
SELECT NE W S E T T I N G
METRIC [ENGLISH]
This chapter provides instructions on accessing and using the features provided with the
Detroit Diesel Marine Controls Application.
↑----Selections---- ↓
DDEC III/IV xx.x
2 Select Marine Controls Menu. The screen displays the Marine Controls Menu.
MARINE CONTROLS
MENU
↑----Selections---- ↓
DATA LIST
MARINE CONTROLS
MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
2 Press to select DATA LIST. The screen displays the data list. For
example:
4 Press when finished viewing the data. The screen returns to the
MARINE CONTROLS MENU.
MARINE CONTROLS
MENU
↑----Selections---- ↓
DATA LIST
• Active Codes
• Codes Since Last Power Up
• Historic Codes
MARINE CONTROLS
MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
DIAGNOSTIC CODES
↑- - - - S e l e c t ions---- ↓
ACTIVE CODES
5 Press when finished viewing the data. The screen returns to the DIAG-
NOSTIC CODES menu.
DIAGNOSTIC CODES
↑----Selections---- ↓
ACTIVE CODES
NOTE:
i See “Defect Codes”, on page 213 for a complete list of all diagnostic codes
and their possible values.
MARINE CONTROLS
MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
DIAGNOSTIC CODES
↑- - - - S e l e c t ions---- ↓
ACTIVE CODES
3 Select CODES SINCE POWER UP. The screen displays the codes. For
example:
5 Press when finished viewing the data. The screen returns to the DIAG-
NOSTIC CODES menu.
DIAGNOSTIC CODES
↑----Selections---- ↓
CODES SINCE POWER UP
Use the Historic Codes feature to view all diagnostic codes that were logged during
the life of the ERIM and are currently stored in memory.
NOTE:
i This feature is not available for ERIM Software Level 3.0 or lower.
NOTE:
i See “Marine Controls Historic Codes”, on page 202 for a complete list of
all diagnostic codes and their possible values.
MARINE CONTROLS
MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
DIAGNOSTIC CODES
↑- - - - S e l e c t ions---- ↓
ACTIVE CODES
3 Select HISTORIC CODES. The screen displays the codes. For example:
DIAGNOSTIC CODES
↑----Selections---- ↓
HISTORIC DATA
Viewing Calibrations
Use the View Calibrations feature to view the operating parameters that are
stored in the memory of the ERIM.
MARINE CONTROLS
MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
VIEW CALIBRATIONS
↑- - - - S e l e c t ions---- ↓
MARINE CAL
Viewing Calibrations
VIEW CALIBRATIONS
↑----Selections---- ↓
MARINE CAL
VIEW CALIBRATIONS
↑- - - - S e l e c t ions---- ↓
MARINE CAL
2 Select ENGINE CAL. The screen displays the calibration data. For example:
Viewing Calibrations
NOTE:
i This option is not available for version 2.0 or 2.5 marine controls.
To view marine gear actuator calibration:
1 Be sure that the View Calibrations menu is displaying.
VIEW CALIBRATIONS
↑----Selections---- ↓
MARINE CAL
2 Select GEAR ACTUATOR CAL. The screen displays calibration data. For
example:
NOTE:
i This option is not available for version 2.0 or 2.5 marine controls.
NOTE:
i See “Troll Mode Calibration”, on page 208 for a complete list of all troll
mode parameters and possible values.
VIEW CALIBRATIONS
↑- - - - S e l e c t ions---- ↓
MARINE CAL
2 Select TROLL MODE CAL. The screen displays the calibration data. For
example:
TROLL SYSTEM NO
PT TROLL VER XXXXXXX
PT TROLL CKSM 1 00
SD TROLL VER XXXXXXX
Viewing Calibrations
—If the software version is below 3.0, the screen displays the following
message:
THIS FUNCTION IS
NOT AVAILABLE FOR
ERIM SW BELOW 3
[CONTINUE] CANCEL
NOTE:
i See “Switch and Light Status Parameters”, on page 208 for a list of all
Switch/Light parameters.
MARINE CONTROLS
MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
2 Select the SWITCH/LIGHT STATS option. The screen displays the Switch/Light
Stats menu.
S W I T C H / L I G HT S T A T S
↑- - - - S e l e c t ions---- ↓
S W I T C H / L I G HT S T A T S
ACTIVE BUTTON ON
S T A A C T I V E L A MP ON
SYNC BUTTON OF F
SYNC LAMP ON
Use the MIDS Received function to view the device that is sending out a MID.
NOTE:
i If more than one device is active, arrows display on the bottom line.
To view MIDS received:
1 Be sure that the Marine Controls Menu is displaying, as follows:
MARINE CONTROLS
MENU
↑- - - - S e l e c t ions---- ↓
DATA LIST
2 Select MIDS RECEIVED. The screen displays each device that is sending out
a MID. For example:
ENGINE
MID 128
This chapter provides instructions on accessing and using the features provided with the
Detroit Diesel Series 638 Application.
↑----Selections---- ↓
DDEC III/IV xx.x
2 Select Series 638 X.X. The screen displays the following messages:
LOADING
“SERIES 638 x.x”
PLEASE WAIT...
—If you have loaded the DDEC III/IV application, the screen prompts you to
re-boot the MPC.
Protocol Change
Required
Reboot MPC Now
[ENTER] TO CONTINUE
NOTE:
i Refer to the Pro-Link® User’s Manual for instructions.
Press , then reboot the MPC.
3 Wait for communication to be established with the Series 638 system. The
screen displays the Series 638 menu.
SERIES 638
↑- - - - S e l e c t ions---- ↓
DATA LIST
NOTE:
i See “Data List”, on page 211 for a complete list of all data list parameters.
To monitor a data list parameter:
1 Be sure that the Series 638 Application menu is displaying.
SERIES 638
↑----Selections---- ↓
DATA LIST
2 Press to select DATA LIST. The screen prompts you to select a param-
eter to monitor.
SELECT A PARAMETER
TO MONITOR
↑ W A T E R T E M P ERATURE ↓
3 Press the or key to scroll to and select the parameter that you
want to monitor, then press . The screen displays the parameter infor-
mation. For example:
WATER TEMPERATURE
72.5
NOTE:
i See “Defect Codes”, on page 213 for a complete listing of defect code
parameters.
SERIES 638
↑----Selections---- ↓
DATA LIST
2 Select DEFECT CODES. The screen displays the Defect Codes menu.
DEFECT CODES
↑----Selections---- ↓
VIEW CODES
3 Select VIEW CODES. The screen displays the defect codes information. For
example:
1 of 4 P0500
POWERTRAIN
VEHSPEEDSENS
SERIES 638
↑- - - - S e l e c t ions---- ↓
DATA LIST
2 Press to select the DEFECT CODES option. The screen displays the
Defect Codes menu.
DEFECT CODES
↑----Selections---- ↓
VIEW CODES
3 Select CLEAR CODES. The screen prompts you to confirm that you want to
clear the codes.
CLEAR CODES
ARE YOU SURE?
YES [NO]
4 Select YES. The screen indicates that the codes are being cleared.
CLEARING CODES
PLEASE WAIT...
Once the defect codes are cleared, the screen displays the following
message:
CODES CLEARED
[ENTER] TO CONTINUE
DEFECT CODES
↑- - - - S e l e c t ions---- ↓
CLEAR CODES
NOTE:
i See “I/O Status List Parameters”, on page 215 for a list of all I/O Status
data list parameters.
SERIES 638
↑----Selections---- ↓
DATA LIST
2 Select I/O STATUS. The screen prompts you to select a parameter to monitor.
SELECT A PARAMETER
TO MONITOR
AGR/EGR ACTUATOR
3 Press the or key to scroll to and select the parameter that you
want to monitor, then press . The screen displays the parameter infor-
mation. For example:
AGR/EGR ACTUATOR
OFF
Parameter
Listings
T his appendix contains all parameter listings that exist for each of the vehicle system
applications within the Detroit Diesel Application program.
The following table provides all parameter listings and corresponding page
numbers:
Parameter Page #
Engine Data List 142
Engine and Vehicle Configuration 150
Idle Shutdown Configuration 155
VSG (Marine Throttle) Calibration 156
Engine Protection Configuration 157
Cruise Control Configuration 158
Progressive Shift Configuration 160
ECM Input/Output Configuration 162
Air Compressor Configuration 164
Function Lockout Configuration 165
Injector Calibration 167
Total Engine Data 167
Engine Trip Data 168
Idle Shutdown Calibration 170
VSG (Marine Throttle) Reprogrammable Calibration 171
Engine Protection Calibration 172
Cruise Control Calibration 174
Progressive Shift Calibration 177
Engine Droop Options 179
Engine and Vehicle Options 179
Engine Rating Calibration 181
Air Compressor Calibration 183
Parameter Page #
Transmission Calibration 183
Top 2 Transmission 184
Maintenance Alert System Calibration 185
ECM Input Switches 186
ECM Output Status 187
Activate ECM Output 189
Transmission Configuration 191
Performance Data 191
Transmission Trip Data 192
Maintenance Alert System 193
Parameter Description
ACTIVE CODES Indicates (Yes or No) whether an active Fault Code is
present.
AIR FILTR RS Indicates the relative amount of restriction measured
at the Air Inlet Filter, inches of H2O or KPa.
AIR INLET TMP Indicates the temperature of the air entering the
engine air induction system in degrees Fahrenheit or
Celsius.
AIR INLET PSI Indicates the engine air inlet pressure in PSI or KPa.
AIR TMP TQ LIMIT Indicates the active/inactive status of the Air Temper-
ature Engine Torque Reduction Mode.
ALARM Indicates the status of the optimized idle alarm mode.
ALERT MODE Indicates the active/inactive status of the idle
shutdown Driver Alert Mode.
ALT THROT CNTS Throttle counts. “N/A” will be displayed if the A/D port
(MARINE) mask for Throttle Position is disabled as indicated by
DDEC Unique ID 223.
AMB AIR TMP Indicates the temperature of the air surrounding the
vehicle in degrees Fahrenheit or Celsius.
BARO PRS PSI Indicates the atmospheric pressure in PSI or KPa.
BOI Beginning of Injection - specifies the timing of the
injection event as the number of degrees crankshaft
rotation before piston TDC.
BOOST PSI OR KPA Pressure of air measured downstream on the com-
pressor discharge side of the turbo-charger. Indicated
in PSI or KPa “FAIL” will display if a FMI 3 or FMI 4 is
received.
BYP VALVE Indicates the percent opening of the blower bypass
valve.
COMP BLEED Cylinder Boost Differential Pressure measures the
difference between the Turbine Inlet Pressure and
the Turbocharger Compressor Outlet Pressure.
Parameter Description
COOL TMP Indicates the temperature of the engine coolant in
degrees Fahrenheit or Celsius.
COOLANT LEVEL Indicates the engine coolant level, determined by the
Coolant Level Sensor. Will display FULL, ADD or
LOW. Some engines may be equipped with an
optional Second Coolant Level Sensor.
COOLANT PSI OR Indicates the engine coolant system pressure in PSI
KPA or KPa.
CRNKCSE H20 OR Indicates the air pressure inside the engine crank-
KPA case in inches of water or KPa.
CRUISE SET MPH OR Indicates the cruise control set speed.
KPH
ECM VOLTS Indicates the battery voltage available to the ECM.
ECON MPG Indicates the current fuel economy at the current
vehicle velocity.
EGR DPS A* Differential pressure across the EGR flow measure-
ment device.
EGR DPS B* Differential pressure across the EGR flow measure-
ment device.
*EGR Parameters with “A” suffix pertain to ECM software versions below R33.0. EGR
parameters with “B” suffix pertain to ECM software versions at or above R33.0. See
parameter “SOFTWARE LVL” in the “Engine and Vehicle Configuration”, on page 150
EGR DPS CNTS Indicates the raw analog counts of the EGR orifice
pressure drop.
EGR TMP A* Temperature of the re-circulated exhaust gas after the
EGR cooler.
EGR TMP B* Temperature of the re-circulated exhaust gas after the
EGR cooler.
*EGR Parameters with “A” suffix pertain to ECM software versions below R33.0. EGR
parameters with “B” suffix pertain to ECM software versions at or above R33.0. See
parameter “SOFTWARE LVL” in the “Engine and Vehicle Configuration”, on page 150
Parameter Description
ENG GOVR Indicates which DDEC governor is currently active.
ENG GOVR GAIN Overall governor gain.
ENG LOAD PCT Indicates the percent engine load calculated from
engine speed and torque.
ENGINE RPM Indicates engine RPM as determined by the timing
reference sensor.
EXST BKPRS Indicates exhaust back pressure in Hg or KPa. “FAIL”
will display if FMI 3 or FMI 4 is received.
EXST BP FAULT Exhaust back pressure fault times.
TIMES
• SCLD HI • Exhaust back pressure time while scaled high
fault active, indicated in hours/minutes.
• RAMP DN • Exhaust back pressure time while ramp down
fault active, indicated in hours/minutes.
EXHST GAS AFR Indicates the engine exhaust gas air fuel ratio.
EXST TMP A Indicates the temperature of the engine exhaust gas
in degrees Fahrenheit or Celsius. For marine
engines, indicates exhaust bank A temperature.
“FAIL” will be displayed if a FMI 3 or FMI 4 is
received.
EXST TMP B Indicates the temperature of the Receiver ECM #2
(MID 175) engine exhaust gas in degrees Fahrenheit
or Celsius. For marine engines, indicates exhaust
bank B temperature. “FAIL” will be displayed if a FMI
3 or FMI 4 is received.
EXT PUMP PSI Indicates water pressure of an external water pump
drive in PSI or KPa.
FUEL IN RES Indicates the restriction measured at the Fuel Pump
Inlet, inches of Hg or KPa.
FUEL PRS PSI Indicates the engine fuel pressure in PSI or KPa.
FUEL TMP Indicates the temperature of the engine fuel in
degrees Fahrenheit or Celsius.
FUEL RATE GPH OR Indicates the amount of fuel consumed by the engine
LPH per unit time.
Parameter Description
GAS VALVE Indicates the percent opening of the natural gas
metering valve.
HALF ENGINE Indicates the active/inactive status of the Half Engine
Mode.
INACTIVE CODES Indicates (Yes or No) if an inactive Fault Code has
been present.
IDLE SPD RPM Indicates the current engine idle speed in RPM.
INJECT PRS PSI Indicates the injection fuel rail pressure in PSI or
KPa.
INJ PUMP USAGE Indicates the injection fuel rail pump utilization.
ISD OPTION Indicates the state of the idle shutdown feature.
INTKE AIR TMP Indicates the temperature of the engine intake air
degrees Fahrenheit or Celsius.
INTRCOOL TMP Indicates the temperature of the engine intercooler
degrees Fahrenheit or Celsius.
KNOCK CONTROL Indicates the active/inactive status of the Knock
Control Mode.
KNOCK LEVEL A description of the relative knock intensity. The
higher the numbers the higher the knock.
KNOCK VOLTS Indicates the knock sensor voltage available to the
ECM.
LOOP STATUS Indicates the open/closed loop status of the fuel
system based on the signal from an exhaust oxygen
sensor.
OIL FILTR RS Indicates the relative amount of restriction measured
at the Oil Filter, in PSI or KPa.
OIL LEVEL Indicates the engine oil level. Will display OK or ADD.
While the engine is running, and for a while after
shutting off the engine, OIL LEVEL will display
UNKNOWN.
OIL PRS PSI Indicates the engine oil pressure in PSI or KPa.
OIL TMP Indicates the temperature of the engine oil in degrees
Fahrenheit or Celsius.
Parameter Description
OPTIMIZED IDLE Indicates the enabled/disabled status of the opti-
mized idle feature that is programmed in the DDEC
calibration.
OVERRIDE Indicates the active/inactive status of the idle
shutdown override feature.
PULSEWIDTH Number of degrees crankshaft rotation that the EUI’s
control valve is closed and fuel is entering the
cylinder.
PWM DRIVE 1 Indicates the duty cycle of the Pulse Width Modulated
(PWM) port #1.
PWM DRIVE 2 Indicates the duty cycle of the Pulse Width Modulated
(PWM) port #2.
PWM DRIVE 3 Indicates the duty cycle of the Pulse Width Modulated
(PWM) port #3.
PWM DRIVE 4 Indicates the duty cycle of the Pulse Width Modulated
(PWM) port #6.
R1 INLET TMP Indicates the receiver ECM #1 (MID 175) temperature
of the air entering the engine air induction system in
degrees Fahrenheit or Celsius.
R1 BOOST Receiver ECM #1 (MID 175) Boost Pressure -
Pressure of air measured downstream on the com-
pressor discharge side of the turbocharger.
R1 SRS RECEIVED Indicates that the receiver ECM #1 (MID 175) has
received a signal from the Synchronous Reference
Sensor (SRS) during this ignition cycle.
R1 ECM VOLTS Indicates the receiver ECM #1 (MID 175) battery
voltage available to the ECM.
R1 PULSEWIDTH Receiver ECM #1 (MID 175) Fuel Pulse Width.
• R1 TPS CNTS Indicates the receiver ECM #1 (MID 175) Throttle
(STANDARD) Position Sensor (TPS) Counts (CTS) - A/D Counts.
• R1 ALT THROT For marine engines, indicates the alternate throttle
CNTS (MARINE) counts. “N/A” will be displayed if the A/D port mask
for Throttle Position is disabled as indicated by DDEC
Unique ID 223.
Parameter Description
• R1 VSG CNTS Indicates the receiver ECM #1 (MID 175) Variable
(STANDARD) Speed Governor (VSG) - A/D counts. For marine
• R1 THROT CNTS engines indicates the main throttle counts. “N/A” will
(MARINE) be displayed if the A/D port mask for PTO position is
disabled as indicated by DDEC Unique ID 223.
R1 OIL PRS Indicates the receiver ECM#1 (MID 175) engine oil
pressure in PSI or KPa.
R2 OIL PRS Indicates the receiver ECM#2 (MID 183) engine oil
pressure in PSI or KPa.
R1 INLET PSI Receiver ECM #1 (MID 175) indicates the engine air
inlet pressure in PSI or KPa.
R1 BARO PSI Receiver ECM #1 (MID 175) Barometric Pressure -
indicates the atmospheric pressure in PSI or KPa.
R1 COOL PSI Indicates the receiver ECM #1 (MID 175) engine
coolant system pressure in PSI or KPa.
R1 TURBO SPEED Indicates the receiver ECM #1 (MID 175) Turbo blade
speed RPM.
R2 COOL PRS Indicates the receiver ECM#2 (MID 183) engine
coolant system pressure in PSI or KPa.
R2 ECM VOLTS Indicates the receiver ECM #2 (MID 183) battery
voltage available to the ECM.
R2 PULSEWIDTH Receiver ECM #2 (MID 183) Fuel Pulse Width.
R2 SRS RECEIVED Indicates that the receiver ECM #2 (MID 183) has
received a signal from the Synchronous Reference
Sensor (SRS) during this ignition cycle.
• R2 TPS CNTS Indicates the receiver ECM #2 (MID 183) Throttle
(STANDARD) Position Sensor (TPS) Counts (CTS) - A/D Counts.
• R2 ALT THROT For marine engines, indicates the alternate throttle
CNTS (MARINE) counts. “N/A” will be displayed if the A/D port mask
for Throttle Position is disabled as indicated by DDEC
Unique ID 223.
R2 TURBO SPEED Indicates the receiver ECM #2 (MID 183) Turbo blade
speed RPM.
Parameter Description
• R2 VSG CNTS Indicates the receiver ECM #2 (MID 183) Variable
(STANDARD) Speed Governor (VSG) - A/D counts. For marine
• R2 THROT CNTS engines, indicates the main throttle counts. “N/A” will
(MARINE) be displayed if the A/D port mask for PTO position is
disabled as indicated by DDEC Unique ID 223.
REL HUMID Indicates relative humidity. “FAIL” will display if FMI 3
or FMI 4 is received.
SEQ TURBO Indicates the status of the Sequential Turbo Mode.
SPD ADJUST MPH Indicates the adjusted vehicle road speed in MPH or
KPH.
SRS RECEIVED Indicates that the ECM has received a signal from the
Synchronous Reference Sensor (SRS) during the
ignition cycle.
SHUTDOWN Indicates whether the engine has been shutdown by
the idle shutdown feature.
START RLY Indicates the status of the optimized idle starter relay.
SYS ACTIVE Indicates the active status of the optimized idle
system.
THROTTLE PLATE Indicates the percent opening of the natural gas
throttle plate.
TIMER Indicates the active/inactive status of the idle
shutdown timer.
TORQ LB-FT Indicates the amount of torque available at the engine
flywheel. Negative torque values will display with a
minus sign (-) in front of the value.
TPS CNTS Indicates the Throttle Position Sensor (TPS) Counts
(STANDARD) (CTS) - A/D Counts. For marine engines indicates the
alternate.
• TPS PCT Indicates the percent opening of the throttle position
(STANDARD) sensor (TPS). For marine engines indicates the
• ALT THROT PCT percent opening of the alternate throttle. “FAIL” will be
(MARINE) displayed if a FMI 3 or FMI 4 is received. “N/A” will be
displayed if the A/D port mask for Throttle Position is
disabled as indicated by DDEC Unique ID 223.
TRB CMP OUT Indicates turbocharger compressor outlet tempera-
ture in degrees Fahrenheit or Celsius. “FAIL” will
display if FMI 3 or FMI 4 is received.
Parameter Description
TRB CMP IN Indicates turbocharger compressor inlet temperature
in degrees Fahrenheit or Celsius. “FAIL” will display if
FMI 3 or FMI 4 is received.
TRB BYP VLV Turbocharger Compressor Bleed Valve, ON or OFF.
FAULT is displayed when the output is switched OFF
if the TRB BYP DP is too high, which will prevent
unwanted exhaust gas recirculation. Displays “N/A” if
not configured.
T-STAT Indicates the status of the optimized idle thermostat
control mode.
%TQ LIMIT Torque Reduction Factor - indicates the ratio of
current output torque allowed (due to adverse operat-
ing conditions) to maximum torque available at
current engine speed (under normal operation
conditions).
TURBO SPEED Indicates the Turbo blade speed in RPM.
VEHICLE SPD MPH Indicates the vehicle road speed in MPH or KPH.
• VSG CNTS Indicates the Variable Speed Governor (VSG) - A/D
(STANDARD) counts. For marine engines, indicates the main
• THROT CNTS throttle counts. “N/A” will be displayed if the A/D port
(MARINE) mask for PTO position is disabled as indicated by
DDEC Unique ID 223.
• VSG SET RPM Indicates the engine set speed for the Variable Speed
(STANDARD) Governor. For marine engines indicates the throttle
• THROT SET RPM set speed.
(MARINE)
Parameter Description
ECM DATE Indicates the current date stored in the DDEC
engine controller.
ECM TIME Indicates the current time stored in the DDEC
engine controller1.
ENG MODEL # Indicates the Detroit Diesel Corporation engine
model number that is programmed in the DDEC
calibration.
6N4M # Indicates the engine rating group designation.
R1 6N4M # Indicates the engine rating group designation for
Receiver #1 ECM2.
R2 6N4M # Indicates the engine rating group designation for
Receiver #2 ECM3.
6N4D # Indicates the engine rating family designation.
R1 6N4D # Indicates the engine rating family designation for
Receiver #1 ECM5.
R2 6N4D # Indicates the engine rating family designation for
Receiver #2 ECM3.
6N4C # Indicates the engine application group designation.
R1 6N4C # Indicates the engine application group designation
for Receiver #1 ECM5.
R2 6N4C # Indicates the engine application group designation
for Receiver #2 ECM3.
UNIT# Indicates the vehicle unit number that is pro-
grammed by the customer to identify the vehicle
within their fleet electronically4.
V Indicates the vehicle identification number that is
programmed in the DDEC calibration.
ENG S/N Indicates the engine serial number that is pro-
grammed in the DDEC calibration.
Parameter Description
ECM S/N Indicates the ECM serial number that is pro-
grammed in the DDEC calibration.
R1 ECM SN Indicates the engine serial number for Receiver #1
ECM3.
R2 ECM SN Indicates the engine serial number for Receiver #2
ECM4.
SOFTWARE LVL Indicates the DDEC ECM software version. The
software level is incremented after every revision.
R1 SOFTWARE Indicates the engine software version for Receiver
#1 ECM3.
R2 SOFTWARE Indicates the engine software version for Receiver
#2 ECM4.
EPA CERT # Indicates the EPA engine certification number.
R1 EPA CERT # Indicates the engine certification number for
Receiver #1 ECM3.
R2 EPA CERT # Indicates the engine certification number for
Receiver #2 ECM4.
ENG SERIES Indicates the DDEC engine type.
SHARED VERS Indicates the version number of the shared
parameters.
R1 SHARED VERS Indicates the receiver ECM #1 (MID 175) version
number of the shared parameters.
R2 SHARED VERS Indicates the receiver ECM #2 (MID 183) version
number of the shared parameters.
RATING VERS Indicates the version number of the rating parame-
ters. For a standard rating, it is displayed XXX. For
a cruise rating, it is displayed XXX/XXX.
R1 RATING VERS Indicates the ECM #1 (MID 175) version number of
the rating parameters. For a standard rating, it is
displayed XXX. For a cruise rating, it is displayed
XXX/XXX.
R2 RATING VERS Indicates the ECM #2 (MID 183) version number of
the rating parameters. For a standard rating, it is
displayed XXX. For a cruise rating, it is displayed
XXX/XXX.
Parameter Description
ENG PWR Indicates the rated brake horsepower of the cur-
rently active rating.
ENG RATED RPM Indicates the rated speed of the currently active
rating.
LSG DROOP RPM Indicates the rated speed governor droop that is
programmed in the DDEC calibration.
PEAK TRQ Indicates the peak operating torque of the currently
active rating.
PEAK TRQ RPM Indicates the RPM at peak torque of the currently
active rating.
IDLE SPEED Indicates the warm engine idle speed that is pro-
grammed in the DDEC calibration.
IDLE ADJUST Indicates the idle RPM adjustment.
TRANS Indicates the vehicle transmission type.
DYNAMIC BRAKING Indicates the enabled/disabled status of the engine
fan dynamic braking feature.5
ENG BRK/SER BRK Indicates the enabled/disabled status of the engine
brake engaged by the vehicle service brake
feature.
ENG BRAKE MIN MPH Indicates the minimum vehicle speed in which the
engine brake engaged by the vehicle brake in
activated.
HALF ENGINE Indicates how half engine mode will depend on
temperature.
DATA PAGES Indicates the enabled/disabled status of the data
pages feature.
J1922 ABS ENABLE Indicates the enabled/disabled status of the SAE
J1922 ABS communications feature.
J1922 TRN ENABLE Indicates the enabled/disabled status of the SAE
J1922 transmission communications feature.
J1939 ENABLED Indicates the enabled/disabled status of the SAE
J1939 communications feature.
H20 GOV ENABLED Indicates the enabled/disabled status of the fire
truck water pressure governor feature.
Parameter Description
AIR GOV ENABLED Indicates the enabled/disabled status of the air
compressor pressure governor feature.
A/C FAN TIMER Indicates the A/C FAN on time in seconds. This
value can range from 0 to 255 seconds.
FUEL ECON INCENTIVE This feature will add a MPH delta to the cruise and
road speed maximums based on average fuel
economy. The feature is to operate the vehicle in
such a way as to maximize MPG.
MINIMUM MPG Indicates the minimum MPG (or Maximum L/100
K) threshold to enable the cruise and road speed
adjustment feature that is programmed in the
DDEC calibration.
MAX SPEED Indicates the maximum adjustment value for cruise
and road speed adjustment that is programmed in
the DDEC calibration.
ECON Fuel economy for maximum speed delta adjust-
ment. Indicates the calculated MPG (or L/100km)
for the maximum speed adjustment value.
This parameter is calculated using the programma-
ble parameters “MINIMUM MPG”, “MAX SPEED”,
and the current value given by the engine controller
for conversion factor (formerly the MPC displayed
parameter “SCALER”). The calculation is:
ECON = (MAX SPEED / conversion factor) +
MINIMUM MPG
CALC TYPE Indicates the speed adjustment calculation type
that is programmed in the DDEC calibration. The
speed adjustment can be calculated from short-
term MPG or long-term MPG.
Low Gear TRQ Limit
TRQ LMT FT-LB Indicates the low gear torque limit.
Parameter Description
THRESHOLD Indicates the low gear torque limiting threshold.
SET SPEED Indicates the low gear torque limiting set speed in
MPH (or KPL).
IDLE METHOD Indicates which method will be used to determine if
the engine is on idle for the purposes of idle data
accumulation. If VSS ENABLED = YES, VSS will
be displayed.
LOAD LIMIT If IDLE METHOD is RPM/LOAD, displays the load
limit under which idle data will be accumulated.
Display N/A if VSS ENABLED = YES or if IDLE
METHOD = IDLEGOV.
RPM LIMIT If IDLE METHOD is RPM/LOD, displays the wpm
limit under which idle data will be accumulated.
Display N/A if VSS ENABLED = YES or if IDLE
METHOD = IDLEGOV.
1 If the DDEC ECM software version is 20.0 or higher, the time will be indicated in
GMT (Greenwich Mean Time). See next page for footnotes 2 - 5.
2 These features are only available on Multi-ECM Engines, with a Receiver #1 ECM,
MID 175.
3 These features are only available on Multi-ECM Engines, Receiver #2, MID 183.
4 10-digit alpha/numeric entry.
5 These features are only available on ECM with Software Level 2.0 or higher.
NOTE:
i These features are only available on ECM with Software Level 2.0 or
higher.
Parameter Description
ENABLED Indicates the enabled/disabled status of the engine idle
shutdown feature that is programmed in the DDEC cal-
ibration. “N/A” will be displayed if function #5 (PARK
BRAKE/ISD) is not configured as a vehicle input
switch.
TIME (MIN) Indicates the engine idle time in minutes that is allow-
able before the idle shutdown feature stops fueling the
engine. “N/A” will be displayed if idle shutdown
“ENABLED” = NO or N/A.
OVERRIDE Indicates the enabled/disabled status of the engine idle
shutdown override feature that is programmed in the
DDEC calibration. “N/A” will be displayed if idle
shutdown “ENABLED” = NO or N/A.
AUTO OVERRIDE Indicates the enabled/disabled status of the engine idle
shutdown automatic override feature that is pro-
grammed into the DDEC calibration. “N/A” will be
displayed if idle shutdown “ENABLED” = NO or N/A.
ENABLED ON VSG Indicates the enabled/disabled status of the engine idle
shutdown on VSG feature that is programmed in the
DDEC calibration. “N/A” will be displayed if idle
shutdown “ENABLED = NO or N/A.
Override Temp Disable
LOWER LIMIT Indicates the lower limit of the ambient temperature
range that will disable the idle shutdown override
feature.1
UPPER LIMIT Indicates the upper limit of the ambient temperature
range that will disable the idle shutdown override
feature5.
1 These features are only available on ECM with Software Level 2.0 or higher.
Parameter Description
• VSG DROOP RPM Indicates the variable speed governor droop in
(STANDARD) RPM that is programmed in the DDEC calibration.
• THROT DRP RPM For marine engines, this is the amount of Throttle
(MARINE) Droop.
• ALT VSG MIN RPM Indicates the alternate variable speed governor
(STANDARD) minimum RPM that is programmed in the DDEC
• USER IDLE RPM calibration. For marine engines, this is the normal
(MARINE) user idle set point. “N/A” will be displayed if (Func-
tion #16 - ALT VSG MIN) is not configured as a
vehicle input switch.
NOTE:
i “R1” parameters pertain only to multi-ECM engines, Receiver #1, MID
175.
Parameter Description
OIL TMP Indication of the type of engine protection
R1 OIL TMP Indicates the Receiver ECM #1 (MID 175) type of
engine protection based on high engine oil tem-
perature “N/A” will be displayed if the sensor input
is not configured.
COOLANT TMP Indication of the type of engine protection based
on high engine coolant temperature.
INTRCOOL TMP Indication of the type of engine protection based
on the engine intercooler coolant temperature.
OIL PRS Indication of the type of engine protection based
on low engine oil pressure.
CRNKCSE PRS Indication of the type of engine protection based
on engine crankcase pressure.
COOLANT PRS Indication of the type of engine protection based
on engine coolant pressure.
R1 COOLANT PRS Indicates the Receiver ECM #1 (MID 175) type of
engine protection based on engine Coolant Pres-
sure. “N/A” will be displayed if the sensor input is
not configured.
COOLANT LVL Indication of the type of engine protection based
on low coolant level.
OIL LEVEL Indication of the type of engine protection based
on low engine oil level.
AUX SHTDWN #1 Indication of the type of engine protection based
on auxiliary engine shutdown #1.
AUX SHTDWN #2 Indication of the type of engine protection based
on auxiliary engine shutdown #2.
Parameter Description
VSS ENABLED Indicates the enabled/disabled status of the
vehicle speed sensor input that is programmed in
the DDEC calibration.
VSS TYPE Indicates the type of vehicle speed sensor input
that is programmed in the DDEC calibration. “N/A”
will be displayed if “VSS ENABLED” = NO.
VSS TEETH Indicates the number of teeth on the vehicle speed
sensor input that is programmed in the DDEC cali-
bration. “N/A” will be displayed if “VSS ENABLED”
= NO.
VSS SIGNAL (STANDARD) Indicates the type of VSS signal that the ECM is
THRT SIGNAL (MARINE) configured for. For marine engines indicates the
type of throttle signal. “N/A” will be displayed if
VSS ENABLED = NO.
TIRE REVS/MI Indicates the vehicle tire size in REVS per mile
that is programmed in the DDEC calibration. “N/A”
will be displayed if “VSS ENABLED” = NO.
AXLE RATIO Indicates the vehicle rear axle ratio that is pro-
grammed in the DDEC calibration. “N/A” will be
displayed if “VSS ENABLED” = NO.
TOP GEAR Indicates the vehicle final drive ratio that is pro-
grammed in the DDEC calibration. “N/A” will be
displayed if “VSS ENABLED” = NO.
PULSES/MI Indicates the pulses per mile ratio that is pro-
grammed in the DDEC Calibration. “N/A” will be
displayed if “VSS ENABLED” = NO.
VEHICLE SPD LMT Indicates the enabled/disabled status of the
vehicle speed limiting feature that is programmed
in the DDEC calibration. “N/A” will be displayed if
“VSS ENABLED” = NO.
VEHICLE SPD Indicates the maximum vehicle speed in MPH that
is programmed in the DDEC calibration. “N/A” will
be displayed if “VEHICLE SPD LMT” = NO or N/A.
Parameter Description
VSS ANTI-TAMPER Indicates the enabled/disabled status of the “N/A”
will be displayed if “VEHICLE SPD LMT”= NO or
N/A.
CRUISE CONTROL Indicates the enabled/disabled status of the cruise
control feature that is programmed in the DDEC
calibration. “N/A” will be displayed if function #20
(set/coast on) has not been configured for a
vehicle switch input.
MIN CRUZ Indicates the minimum cruise control speed that is
programmed in the DDEC calibration. “N/A” will be
displayed if cruise control “ENABLED” = NO or N/
A or “VSS ENABLED” = NO.
MAX CRUZ Indicates the maximum cruise control speed that
is programmed in the DDEC calibration.
AUTO RESUME Indicates the enabled/disabled status of the
feature that allows automatic cruise control set
speed resume.
CRUZ SW VSG Indicates the enabled/disabled status of the cruise
switched VSG feature that is programmed in the
DDEC calibration. “N/A” will be displayed if “VSS
ENABLED” = NO and/or cruise control
“ENABLED” = NO or N/A.
INIT RPM Indicates the cruise switched VSG initial set speed
that is programmed in the DDEC calibration. “N/A”
will be displayed if “CRUZ SW VSG” = NO or N/A.
RPM INCR Indicates the cruise switched VSG RPM increment
that is programmed in the DDEC calibration. “N/A”
will be displayed if “CRUZ SW VSG” = NO or N/A.
CRUZ/ENG BRK Indicates the enabled/disabled status of the
feature that allows the engine brake to be used
while on cruise control if the vehicle exceeds the
cruise set speed.
CRUZ/ENG BRK Indicates the programmed vehicle speed above
the current cruise set speed that must be reached
before the engine brake will activate the medium
and/or high level of retardation.
Parameter Description
ENG BRK INC Indicates the additional incremental speed which
must be reached before the engine brake will
activate the medium and/or high level of
retardation.
MAX OVRSPD LMT Indicates the vehicle speed above which a diag-
nostic code will be logged if the driver fuels the
engine and exceeds this speed limit. A ‘0’ indi-
cates this feature is disabled.
MAX SPD NO FUEL Indicates the vehicle speed above which a diag-
nostic code will be logged if the vehicle reaches
this speed without fueling the engine. A ‘0’ indi-
cates this feature is disabled.
PASS DUR1 The duration of time per interval that is permitted
at the higher speed. A value of zero will disable
the feature.
PASS RST1 The period of time when the ECM resets to begin
a new period.
PASS SPD1 The additional vehicle speed permitted above the
programmed vehicle speed limit. A value of zero
will disable the feature.
1 If the passing speed function is disabled in the ECU, this value cannot be changed.
Parameter Description
ENABLED Indicates the enabled/disabled status of the pro-
gressive shift feature.
LG #1 OFF SPD Indicates the lower gear #1 turn off speed.
LG #1 RPM LIMIT Indicates the lower gear #1 RPM limit.
Parameter Description
LG #1 MAX LIMIT Indicates the low gear #1 maximum RPM limit.
LG #2 OFF SPD Indicates the lower gear #2 turn off speed.
LG #2 MAX LIMIT Indicates the low gear #2 maximum RPM limit.
HG ON SPD Indicates the high gear turn on speed.
HG RPM LIMIT Indicates the high gear RPM limit.
Parameter Description
LOAD PSI Indicates the delta value above the current air
pressure set point that will initiate the air compres-
sor governor to reload the system that is
programmed in the DDEC calibration.
UNLOAD PSI Indicates the delta value above the current air
pressure set point that will initiate the air compres-
sor governor to unload the system that is
programmed in the DDEC calibration.
MAX RAT #1 PSI Indicates the maximum allowable air pressure set
point for engine rating #1.
MIN RAT #1 PSI Indicates the minimum allowable air pressure set
point for engine rating #1.
MAX RAT #2 PSI Indicates the maximum allowable air pressure set
point for engine rating #2.
MIN RAT #2 PSI Indicates the minimum allowable air pressure set
point for engine rating #2.
MAX RAT #3 PSI Indicates the maximum allowable air pressure set
point for engine rating #3.
MIN RAT #3 PSI Indicates the minimum allowable air pressure set
point for engine rating #3.
NOTE:
i The following table lists parameters available for only software version 4.0
or higher.
Parameter Description
IDLE SHUTDOWN Indicates the enabled/disabled status of the
lockout password protection for the reprogram idle
shutdown menu that is programmed in the DDEC
calibration.
• VSG CALIBRATION Indicates the enabled/disabled status of the
(STANDARD) lockout password protection for the reprogram
• THROTTLE CAL VSG calibration menu that is programmed in the
(MARINE) DDEC calibration. For marine engines, controls
lockout of throttle calibration parameters.
ENGINE PROTECT Indicates the enabled/disabled status of the lock
password protection for the reprogram engine pro-
tection menu that is programmed in the DDEC
calibration.
CRUISE CONTROL Indicates the enabled/disabled status of the
lockout password protection for the reprogram
cruise control menu that is programmed in the
DDEC calibration.
PROGRESS SHIFT Indicates the enabled/disabled status of the
lockout password protection for the reprogram
progressive shift menu that is programmed in the
DDEC calibration.
ENG/VEH OPTIONS Indicates the enabled/disabled status of the
lockout password protection for the reprogram
engine/vehicle options menu that is programmed
in the DDEC calibration.
ENGINE DROOP Indicates the enabled/disabled status of the
lockout password protection for the reprogram
engine droop menu that is programmed in the
DDEC calibration.
Parameter Description
AIR COMPRESSOR Indicates the enabled/disabled status of the
lockout password protection for the reprogram air
compressor menu that is programmed in the
DDEC calibration.
TRANSMISSIONS Indicates the enabled/disabled status of the
lockout password protection for the reprogram
transmission options menu that is programmed in
the DDEC calibration.
MAINT ALERT SYS Indicates the enabled/disabled status of the
lockout password protection for the reprogram
maintenance alert system options menu that is
programmed in the DDE C calibration.
Injector Calibration
The following table lists the calibration parameters for all cylinders.
Parameter Description
CYL# XX CAL YY Indicates the injector calibration that is currently
XX = CYL NUMBER programmed in the ECM.
YY = 1 to 99
LAST UPDATE 0 to 65000 HOURS - Indicates the engine hours of
the last injector calibration update.
TOOL ID # Indicates the tool identification number used 8
characters for the last injector calibration update.
# OF CHANGES: 0 to 255 - Indicates the total number of injector
calibration updates.
Parameter Description
FUEL GAL Indicates the total accumulated amount of fuel
used by engine operation.
HOURS Indicates the total accumulated time of engine
operation.
ODO Indicates the total accumulated vehicle miles
traveled.
IDLE HRS Indicates the total accumulated time of engine
operation at idle.
IDLE FL Indicates the total accumulated amount of fuel
used during engine idle operation.
VSG HRS Indicates the total accumulated time of engine
operation on the variable speed governor.
VSG FL Indicates the total accumulated amount of fuel
used during variable speed governor operation.
CRUZ HRS Indicates the total accumulated time of engine
operation on cruise control.
Parameter Description
ENG BRK HRS Indicates the total accumulated time of engine
brake/retarder operation.
DRV AVG LOAD% Indicates the average engine load while driving
over the life of the change.
REVS Indicates the total engine revolutions in 1000s
over the life of the engine.
Opt Idle Savings
TIME HRS Indicates the time saved on engine operation on
optimized idle.
FUEL GAL Indicates the fuel saved during optimized idle.
Parameter Description
FUEL GAL Indicates the total fuel consumed during a trip.
HOURS Indicates the total accumulated time of operation
of the engine during a trip.
FUEL G/H Indicates the average fuel consumption in gallons
or liters per hour during a trip. Calculated by
dividing the trip fuel gallons/ liters above by the
hours above.
ODO Indicates the distance traveled during a trip.
FUEL ECON Indicates the average miles per gallon for the
distance traveled during a trip.
IDLE HRS Indicates the accumulated time of engine opera-
tion on idle during a trip.
IDLE FL Indicates the accumulated amount of fuel used
during engine idle operation for a trip.
VSG HRS Indicates the accumulated time of engine opera-
tion on the variable speed governor during a trip.
VSG FL Indicates the accumulated amount of fuel used
during variable speed governor operation for a
trip.
Parameter Description
CRUZ HRS Indicates the accumulated time of engine opera-
tion on cruise control during a trip.
ENG BRK HRS Indicates the accumulated time of engine brake/
retarder operation during a trip.
DRV AVG LOAD% Indicates the average engine load while driving
during a trip.
Opt Idle Savings
TIME HRS Indicates the time saved on engine operation on
optimized idle.
FUEL Indicates the fuel saved during optimized idle.
NOTE:
i The Park Brake/ISD (Idle Shut-Down) function must be a switch input to
the ECM to allow idle shutdown to be enabled. This is available through
factory programming only.
NOTE:
i When these parameters display with a value of “N/A”, it typically indicates
that the sensor(s) and/or function is not part of the engine configuration.
TIRE REVS2 100 to 999 Allows selection of tire revolutions per mile
or N/A or kilometer.
AXLE RATIO2 2.00 to Select the vehicle axle ratio.
19.99
TOP GEAR2 0.20 to 2.55 Select the top gear ratio.
VEHICLE SPD LMT2 YES, NO or This puts an upper limit on the speed of the
N/A vehicle.
VEHICLE SPD3 10 MPH to
Allows programming of the maximum
vehicle speed in MPH or KPH.
⎛ RATED RPM
⎝ VSS RATIO
IF
VEHICLE
SPD LMT =
NO
AUTO RESUME4 YES, NO or Allows the cruise auto resume function to
N/A be enabled.
CRZ SW VSG4 YES, NO or Allows the cruise switched function to be
N/A enabled.
INIT RPM5 “VSG MIN Select the cruise switched VSG initial RPM.
RPM” to
“VSG MAX
RPM”
RPM INCR5 1 to 255 Allows the selection of the cruise switched
RPM VSG RPM increment.
CRZ/ENG BRK4 YES, NO or Allows the engine brake to be used while on
N/A cruise control if the vehicle exceeds the
cruise set speed. Engine brakes must also
be configured.
CRZ/ENG BRK MPH6 1 to 7 MPH Vehicle speed above the current set speed
or N/A that must be reached before the engine
brake will activate the low level retardation.
The following table lists the parameters available for the Progressive Shift func-
tion.
NOTE:
i A change in any of the parameters that would cause an indicated depen-
dent parameter to fall out of its valid range will result in the dependent
parameter being implicitly updated as well.
1 “RATED” = Engine Rated RPM. The ECM value for this parameter can be viewed
under the MPC menu “ENGINE MENU/VIEW CALIBRATIONS/ENGINE CONFIG/
ENG RATED”
LSG DROOP RPM 0 to MAX Droop The limiting speed governor droop.
RPM
Parameter Description
UNIT # 10 characters - Allows the reprogramming of the vehicle
unit number identification.
V 17 characters - Allows the reprogramming of the vehicle
identification number.
IDLE ADJUST Typically - 25 to 150 RPM - Allows small adjustment of
the idle RPM.
DYNAMIC YES, NO or N/A - Allows the Dynamic Braking feature to
BRAKING be enabled. Requires that the ECM is configured for
engine brakes and fan controls.
ENG BRK/SER YES, NO or N/A - Allows the engine brake to be activated
BRK when the brake pedal is pressed. Requires engine brakes
to be configured.
ENG BRK MIN (0 to 40 MPH), (0 to 64 KPH), or N/A - Allows program-
ming of the minimum brake operation RPM.
HALF ENGINE Indicates how half engine mode will depend on tempera-
ture. Reprogramming may be disabled as part of the ECM
calibration off, on, if cold.
Parameter Description
FUEL ECON This feature will add a MPH delta to the INCENTIVE
cruise and road speed maximums based on average fuel
economy.
The feature is intended to provide incentive to the driver
to operate the vehicle in such a way as to maximum MPG.
MINIMUM MPG1 Indicates the minimum MPG (or Maximum L/100 K)
threshold to enable the cruise and road speed adjustment
feature that is programmed in the DDEC calibration.
MAX SPEED1 Indicates the maximum adjustment value for cruise and
road speed adjustment that is programmed in the DDEC
calibration.
ECON1 Fuel economy for maximum speed delta adjustment. Indi-
cates the calculated MPG (or L/100km) for the maximum
speed adjustment value. This parameter is calculated
using the programmable parameters “MINIMUM MPG”,
“MAX SPEED”, and the current value given by the engine
controller for conversion factor (formerly the MPC dis-
played parameter “SCALER”). The calculation is:
ECON = (MAX SPEED / conversion factor) + MINIMUM
MPG.
CALC TYPE Indicates the speed adjustment calculation type that is
programmed in the DDEC calibration. The speed adjust-
ment can be calculated from short term MPG or long term
MPG.
IDLE METHOD Indicates which method will be used to determine if the
engine is on idle for the purpose of idle data accumula-
tion. Requires VSS ENABLED = NO.
LOAD LIMIT % If IDLE METHOD is RPM/LOD, displays the load limit
under which idle data will be accumulated.
RPM LIMIT If IDLE METHOD is RPM/LOD, displays the RPM limit
under which idle data will be accumulated.
Transmission Calibration
The following table lists the reprogrammable ESS Transmission parameters.
Top 2 Transmission
The following table presents the parameter available for the Top 2 Transmission
type.
NOTE:
i The Pro-Link® identifies the assigned functions by cavity number and
description. The status of the functions will read as GND, OPN, BAT or N/
A.
• % GND - indicates% of the duty cycle that the signal is at ground potential.
NOTE:
i Glow Plug is limited to 0-25% PWM.
NOTE:
i On multiple ECM engines, outputs may be for each ECM, a title for each
ECM is displayed above each group of outputs.
Active Outputs
MID: 128 ECM Range Description
CHECK ENG LT OPN, GND Allows the activation of the check engine
light.
STOP ENG LT OPN, GND Allows the activation of the stop engine
light.
F3———— – N/A
A2———— OPN, GND, N/A Allows the activation of the output at the
vehicle connector cavity A2. N/A will be
displayed if an output function has not
been assigned.
S3———— BAT, OPN, N/A Allows the activation of the output at the
vehicle connector cavity S3. N/A will be
displayed if an output function has not
been assigned.
T3———— BAT, OPN, N/A Allows the activation of the output at the
vehicle connector cavity T3. N/A will be
displayed if an output function has not
been assigned.
Active Outputs
MID: 128 ECM Range Description
W3———— OPN, GND, N/A Allows the activation of the output at the
engine connector cavity W3. N/A will be
displayed if an output function has not
been assigned.
X3———— OPN, GND, N/A Allows the activation of the output at the
vehicle connector cavity X3. N/A will be
displayed if an output function has not
been assigned.
Y3———— OPN, GND, N/A Allows the activation of the output at the
vehicle connector cavity Y3. N/A will be
displayed if an output function has not
been assigned.
A1———— OPN, GND, N/A Allows the activation of the output at the
vehicle connector cavity A1. N/A will be
displayed if an output function has not
been assigned.
J3———— GND Allows activation of the PWM drive #1
PWM #1XX% output at a specified% duty cycle. N/A
will be displayed if a function has not
been configured.
Y1——— GND Allows activation of the PWM drive #2
PWM #2XX% output at a specified % duty cycle. N/A
will be displayed if a function has not
been configured.
W2——— GND Allows activation of the PWM drive #3
PWM #3XX% output at a specified % duty cycle. N/A
will be displayed if a function has not
been configured.
X2——— GND Allows activation of the PWM drive #4
PWM #4XX% output at a specified % duty cycle. N/A
will be displayed if a function has not
been configured.
Transmission Configuration
The following table lists all parameters that can be reprogrammed in via the Trans-
mission Configuration feature.
Performance Data
The following table lists the parameters available for Transmission Performance
Data.
Parameter Description
OIL LEVEL Indicates the engine oil level displays OK or ADD. Note: While
the engine is running, or for a few minutes after shutting down
the engine, the oil level displays UNKNOWN.
COOL LEVEL Indicates the engine coolant level, determined by the Coolant
Level Sensor. Will display FULL, ADD or LOW. Some engines
may be equipped with an optional Second Coolant Level
Sensor.
AIR FILTER Indicates the condition of the Air Inlet Filter. “ERROR” will be
displayed if the Air Filter Restriction Sensor fails.
Note: After replacing the filter, “PLUGGED” will be displayed
until Inactive codes are cleared.
OIL FILTER Indicates the condition of the Oil Filter. “ERROR” will be dis-
played if the Oil Filter Restriction Sensor fails.
Note: After replacing the filter, “PLUGGED” will be displayed
until Inactive codes are cleared.
FUEL FILTER Indicates the condition of the Fuel Filter. “ERROR” will be dis-
played if the Fuel Filter Restriction Sensor fails. Note: After
replacing the filter, “PLUGGED” will be displayed until Inactive
codes are cleared.
FILTERS Determines the behavior of the Check Engine Light (CEL) on a
maintenance alert for filters. “NO” means that the CEL will not
come on. “FLASH” means it will flash at ignition on only. “CON-
TINUOUS” means the light will stay on when there is an alert,
but will not flash at ignition on. “BOTH’ means the light will
come on continuously when the alert occurs, and will flash at
ignition on.
LEVELS Determines the behavior of the Check Engine Light (CEL) on a
maintenance alert for fluid levels. “NO” means that the CEL will
not come on. “FLASH” means it will flash at ignition on only.
“CONTINUOUS” means the light will stay on when there is an
alert, but will not flash at ignition on. “BOTH’ means the light will
come on continuously when the alert occurs, and will flash at
ignition on.
Page
Parameters Number
Marine Controls Data List 195
Marine Controls Historic Codes 202
Marine Controls Calibration 206
Engine Calibration Parameters 207
Marine Gear Actuator Calibration 207
Troll Mode Calibration 208
Switch and Light Status Parameters 208
Display Description
ERIM MODE Power Up Mode - Performing initial power-up diagnostics.
POWER UP
ERIM MODE Dry Run Mode - Ignition ON; Engine not running.
DRY RUN
ERIM MODE Dual Throttle Mode - Engines being controlled by separate
NON SYNC throttles.
Parameter Description
Marine Controls version 2.0 and 2.5
PORT PRESS Port Pressure Switch is not closed when it should be.
SWITCH
STBD PRESS Starboard Pressure Switch is not closed when it
SWITCH should be.
PORT GR SOLENOID Port Gear Actuator solenoid is not energized when it
should be.
STBD GR SOLENOID Starboard Gear Actuator solenoid is not energized
when it should be.
LOW CSIM VOLTS Active CSIM voltage low.
PORT TROLL NOT Port transmission not fully engaged, still in troll mode.
ENG
STBD TROLL NOT Starboard transmission not fully engaged, still in troll
ENG mode.
Marine Controls version 3.0
NO ERROR CODES –
LOW VOLTAGE Voltage supply at CSIM is low.
@CSIM
ACTUATOR LOW Voltage supply at actuator is low.
VOLTS
ACTIVE CSIM COM Active CSIM is not responding.
LOSS
MSTR CSIM COMM Master CSIM is not responding.
LOSS
CSIM 2 COMM LOSS CSIM #2 is not responding.
CSIM 3 COMM LOSS CSIM #3 is not responding.
CSIM 4 COMM LOSS CSIM #4 is not responding.
CSIM 5 COMM LOSS CSIM #5 is not responding.
CSIM 6 COMM LOSS CSIM #6 is not responding.
Parameter Description
AUX COMM-LINK Loss of auxiliary communications link.
LOSS
ERIM EEPROM ERIM EEPROM write error.
ALERT
ERIM M1 ALERT Port microprocessor error.
ERIM M2 ALERT Starboard microprocessor error.
ERIM NOT DDEC3 ERIM is not of upgraded software.
ALERT
ERIM DIAG ALERT Internal error detected in system.
EXIT SYNC QUAL Occurs when operator exits sync mode and does not
ALERT qualify follower throttle.
BACKUP PANEL System is being controlled by the back up throttle.
ACTIVE
PORT J1708 COMM Loss of all communications on the port link.
LOSS
PORT ENGINE Port engine not running.
STOPPED
PORT POT OUT OF Port throttle potentiometer out of range.
RANGE
PORT THRT QUAL Unexplained loss of throttle qualification on Port
ALERT throttle.
PORT GEAR QUAL Unexplained loss of qualification on Port gear.
ALERT
Port GEAR COMM loss Port gear not responding.
PORT GEAR LOW Low voltage supply at Port gear.
VOLTS
PORT GEAR HI LOAD Loading on Port gear actuator is higher than normal.
PORT GEAR NOT @ Port gear not in neutral when commanded to be in
NEU POS neutral
PORT GEAR NOT @ Port gear not in neutral when commanded to be in
NEU POS neutral.
PORT GEAR NOT @ Port gear not in reverse when commanded to be in
REV POS reverse.
Parameter Description
PORT TROLL COMM Port Troll actuator not responding.
LOSS
PORT TROLL LOW Low voltage supply at Port troll actuator.
VOLTS
PORT TROLL HI LOAD Loading on port troll actuator is higher than normal.
PORT TROLL NOT @ Port troll actuator not in the engaged position when
EGD POS commanded to engage.
PORT TROLL NOT @ Port troll actuator not in the commanded position.
CMD POS
PORT ENG TACH Loss of port engine speed signal.
LOSS
PORT CMD RPM Commanded port RPM out of range.
RANGE
PORT LCP ACTIVE Local control panel controlling the Port engine.
PORT GEAR DIAG Port gear actuator diagnostics failed.
ALERT
PORT TROLL DIAG Port troll actuator diagnostics failed.
ALERT
STBD J1708 COMM Loss of all communications on the Starboard link.
LOSS
STBD ENGINE Starboard engine not running.
STOPPED
STBD POT OUT OF Starboard throttle potentiometer out of range.
RANGE
STBD THRT QUAL Unexplained loss of throttle qualification on Starboard
ALERT throttle.
STBD GEAR QUAL Unexplained loss of qualification on Starboard gear.
ALERT
STBD GEAR COMM Starboard gear not responding.
LOSS
STBD GEAR LOW Low voltage supply at Starboard gear.
VOLTS
STBD GEAR HI LOAD Loading on Starboard gear actuator is higher than
normal.
Parameter Description
STBD GEAR NOT @ Starboard gear not in forward when commanded to
FWD POS be in forward.
STBD GEAR NOT @ Starboard gear not in neutral when commanded to be
NEU POS in neutral.
STBD GEAR NOT @ Starboard gear not in reverse when commanded to
REV POS be in reverse.
STBD TROLL COMM Starboard troll actuator not responding.
LOSS
STBD TROLL LOW Low voltage supply at Starboard troll actuator.
VOLTS
STBD TROLL HI LOAD Loading on Starboard troll actuator is higher than
normal.
STBD TROLL NOT @ Starboard troll actuator not in the engaged position
EGD POS when commanded to engage.
STBD TROLL NOT @ Starboard troll actuator not in the commanded
CMD POS position.
STBD ENG TACH Loss of Starboard engine RPM signal.
LOSS
STBD CMD RPM Commanded Starboard engine RPM out of range.
RANGE
STBD LCP ACTIVE Local Control Panel controlling the Starboard engine.
STBD GEAR DIAG Starboard gear actuator diagnostics failed.
ALERT
STBD TROLL DIAG Starboard troll actuator diagnostics failed.
ALERT
Parameter Description
ERIM VER Current ROM version on the ERIM.
ERIM CHECKSUM Checksum of the current ERIM ROM version.
CSIM1 VER Current ROM version running on CSIM 1.
CSIM1 CHECKSUM Checksum of the current CSIM 1 ROM version.
CSIM2 VER Current ROM version running on CSIM 2.
CSIM2 CHECKSUM Checksum of the current CSIM 2 ROM version.
CSIM3 VER Current ROM version running on CSIM 3.
CSIM3 CHECKSUM Checksum of the current CSIM 3 ROM version.
CSIM4 VER Current ROM version running on CSIM 4.
CSIM4 CHECKSUM Checksum of the current CSIM 4 ROM version.
CSIM5 VER Current ROM version running on CSIM 5.
CSIM5 CHECKSUM Checksum of the current CSIM 5 ROM version.
CSIM6 VER Current ROM version running on CSIM 6.
CSIM6 CHECKSUM Checksum of the current CSIM 6 ROM version.
Parameter Description
PORT LOW IDLE Indicates the “Low Idle” RPM set point for the Port
RPM engine.
STBD LOW IDLE Indicates the “Low Idle” RPM set point for the Starboard
RPM engine.
PORT MAX RPM Indicates the maximum RPM set point for the Port
engine.
STBD MAX RPM Indicates the maximum RPM set point for the Starboard
engine.
PORT USER IDLE Indicates the “User Idle” RPM set point for the Port
RPM engine.
STBD USER IDLE Indicates the “User Idle” RPM set point for the Starboard
RPM engine.
Parameter Description
PT ACTU VER Current ROM version running on the Port Gear Actuator.
PT ACTU CKSM Checksum of the Port Gear Actuator ROM version.
SD ACTU VER Current ROM version running on the Starboard Gear
Actuator.
SD ACTU CKSM Checksum of the Starboard Gear Actuator ROM version.
Parameter Description
TROLL SYSTEM Indicates the presence of a trolling system on the
boat.
PT TROLL VER Current Port Troll ROM version running on the
CSIM.
PT TROLL CKSM Checksum of the Port Troll ROM version.
SD TROLL VER Current Starboard Troll ROM version running on
the CSIM.
SD TROLL CKSM Checksum of the Starboard Troll ROM version.
Parameter Description
ACTIVE BUTTON Indicates whether the active CSIM’s station active
button is being depressed.
STA ACTIVE LAMP Indicates whether ERIM is commanding CSIM to
illuminate the station active lamp.
SYNC BUTTON Indicates whether the active CSIM’s sync button is
being depressed.
SYNC LAMP Indicates whether ERIM is commanding CSIM to
illuminate the sync lamp.
LOW IDLE BUTTON Indicates whether the active CSIM’s low idle
button is being depressed.
LOW IDLE LAMP Indicates whether ERIM is commanding CSIM to
illuminate the low idle lamp.
TROLL BUTTON Indicates whether the active CSIM’S troll button is
being depressed.
TROLL LAMP Indicates whether ERIM is commanding CSIM to
illuminate the troll lamp.
Parameter Description
OVERLOAD OVERIDE Indicates whether the active CSIM’s engine
overload override button is being depressed. Only
available for version 3.0 marine controls.
STA TRANSFER L/O Indicates whether the active CSIM’s station
transfer lockout button is being depressed. Only
available for version 3.0 marine controls.
LOW BATT RELAY Indicates if the CSIM has deactivated the alarm
relay allowing the low voltage alarm to turn on.
SYSTEM ALARM Indicates if a command is being sent to flash the
station active lamp for a code indication.
CSIM ACTIVE RLY Indicates if the CSIM has energized the CSIM
active relay. Only available for version 3.0 marine
controls.
Data List
The following table lists all data list parameters for the Series 638 engine.
Defect Codes
The following table lists all Defect Code parameters.
Parameter Description
Timing ADV Indicates the timing Advance Actuator,% activated
AGR/EGR Indicates the AGR/EGR,% activated
A/Trans Relay Indicates the ON/OFF state of the A/Transmission Relay
Glow Plug Relay Indicates the ON/OFF state of the Glow Plug Relay
Glow Time Phases Indicates the value of Glow Time Phases
16 - Pre Glow
48 - Careless time
(Glow Plug on, Glow
Plug lamp off)
80 - Not Pre Glow
112 - Glow during
crank
176 - After Glow
255 - No Glow
A/C Control Indicates the ON/OFF state of the A/C Control
Glow Plug Aux Relay Indicates the ON/OFF state of the Glow Plug Aux Relay
Glow Plug Display Indicates the ON/OFF state of the Glow Plug Display
Elect Shut Off Indicates the ON/OFF state of the Electric Shut-Off
Diag Lamp Indicates the ON/OFF state of the Diagnostic Lamp
Aux Output #1 Indicates the ON/OFF state of the Auxiliary
Cruise Lamp Indicates the ON/OFF state of the Cruise Lamp
Fan Control #1 Indicates the ON/OFF state of the Fan Control #1
Aux Output #2 Indicates the ON/OFF state of the Auxiliary Output #2
B
Warranty &
Service
Exclusive Warranty
Detroit Diesel Application is warranted for a period of one (1) year from the date
of purchase to be free of defects in materials and workmanship and to be mer-
chantable and fit for its intended purpose.
All warranties are null and void if, after shipment, the product is altered or modified
for any reason by anyone other than NEXIQ Technologies, or is mis-used or
abused. No warranty, express or implied, lasts beyond one (1) year from the date
of purchase. There are no oral warranties of any kind.
Exclusive Remedy
Exclusive Remedy
The sole remedy for breach of warranty or any other obligation (including and
arising out of statute or regulation, strict liability, negligence or the law of torts) is
repair or replacement of defective parts by NEXIQ Technologies or, at the option
of NEXIQ Technologies, refund of the purchase price. This is the exclusive
remedy. ALL LIABILITY OF NEXIQ Technologies FOR CONSEQUENTIAL OR
OTHER DAMAGES IS EXCLUDED AND DISCLAIMED. In no event shall the
Buyer be entitled to damages for lost profits, down time, attorney fees, or business,
economic, or commercial loss or damage of any kind. Action on any claim must be
commenced within one (1) year after the cause of action has accrued.
NEXIQ/NNT Technologies
2329 East Walton Blvd.
Auburn Hills, MI 48326
Attention: Product Service/Repair Department
During the warranty period, NEXIQ Technologies will, at its option, repair or
replace the product which proves to be defective or, refund the purchase price.
Customers MUST obtain a RMA number before repair items are sent in for service.
This is for warranty and non-warranty repairs as well as rework services.
NOTE:
i It is required that the RMA number be written on the outside of the box in
large, bold print.
NEXIQ/NNT Technologies
2329 East Walton Blvd.
Auburn Hills, MI 48326
Attention: Product Service/Repair Department
In addition, we request that you include a business card or your name and phone
number INSIDE the box so we can contact you if there are any repair costs. Any
package sent in for the Product Service department that does not have a RMA
number on the outside of the box WILL BE REFUSED and returned to the sender,
unopened.
Customers MUST obtain a RGA number BEFORE returned items can be returned
to NEXIQ/NNT. Any package sent into NEXIQ/NNT that does not have a RGA
number on the outside of the box WILL be refused and returned to the sender,
unopened.
NOTE:
i NEXIQ/NNT will accept the return of any product, HOWEVER, if the unit is
damaged or items are missing, deductions will be made to the final credit
amount. ANY ITEM THAT IS OBSOLETE OR DETERMINED TO HAVE
NO VALUE WILL NOT RECEIVE CREDIT.
Once authorization for the return is given, it is required to have the RGA number
put on the outside of the box in big bold letters and numbers.
NEXIQ/NNT Technologies
2329 East Walton
Auburn Hills, MI 48326
Attention: Returns/Quality Control Department
NOTE:
i The customer is responsible for return shipping and handling to NEXIQ/
NNT.
Index