Ender-3 S1 Pro-SM-001-User Manual (EN)
Ender-3 S1 Pro-SM-001-User Manual (EN)
Ender-3 S1 Pro
To further improve your user experience, you can find more about our devices via the following methods:
V1.1
User manual: Please find instructions and videos in the SD card provided with the printer.
1 Instructions for Use
1 Do not use this printer by methods or operations not described in this manual, otherwise it may result in accidental
injury or property damage.
2 Do not place this printer near flammable materials, explosive materials or high heat sources. Please place this
printer in a ventilated, cool and low-dust environment.
3 Do not place this printer in a vibrating or any other unstable environment, as the printing quality will be
compromised when the printer shakes.
4 Please use the filament recommended by the manufacturer, otherwise the nozzle may be clogged or the printer
may be damaged.
5 Do not touch the nozzle or hotbed while the printer is in operation, otherwise you may get burned.
6 After the printing process is complete, please use tools to clean up the filament on the nozzle while the nozzle is
still hot. Do not touch the nozzle with your hands when cleaning, otherwise your hands may get burned.
7 Please regularly clean the printer body with a dry cloth while the power is off, and wipe off dust, sticky printing
materials, and foreign objects on the guide rails.
8 This printer has a safety protection mechanism. Please do not manually move the nozzle or printing platform
quickly while the printer is on, otherwise the printer will automatically power off for protection.
9 Users should abide by the laws and regulations of the corresponding country and region where the equipment is
located (place of use) abide by professional ethics, and pay attention to safety obligations. The use of our
products or equipment for any illegal purpose is strictly prohibited. Our company is not responsible for the relevant
legal responsibilities of any violators.
Note: The components above are for reference only. The actual product may vary.
Hotbed
Thermal Port
Hotbed
DC 24 V
Type-C Port
Fuse
Z-Axis
Motor Port
Filament
Detection
Port
+ 24V
Model Fan Port - 24V
PWM
Heat Sink Fan Port
Nozzle Extrusion
Thermal Port Motor Port
5 Install the Printer
5.1 Install the nozzle module and wire clamp
A.Place the nozzle module on the back of the extruder, pre-lock the nozzle with 4 M3x6 hexagon socket head cap
screw, and then tighten it.
B.Clamp the wire clamp onto the X motor black plate.
18 5
Use the short side of the wrench when tightening the screws.
1 Bottom view
16
16
5.3 Install the screen
Place the screen bracket to the side of the plastic that’s on the right, and tighten it with 3 M4x30 hexagon
flat round head screws.
17
5.5 Wiring
X
X
LED light wiring
Z2
Filament detection wiring
115V
230V
Z1
Z-Axis Motor Cable
● Please ensure the correct position for the power supply switch and mains before
supply connection, in order to avoid damage to the device.
● If the mains between 100V and 120V, please select the 115V for the power supply switch.
Caution: ● If the mains between 200V and 240V, please select the 230V for the power supply
switch (default is 230V).
6 Auto Leveling (Please use the CR Touch for automatic leveling first. If the CR Touch lights up in
red and it cannot be leveled, please use the auxiliary leveling again.)
1.Go to "settings" and tap "leveling" to enter the CR Touch leveling interface.
Tap "start" and wait for the automatic leveling to complete.
0%
2.Return to the previous menu. Enter the assisted leveling interface. Adjust the Z-axis compensation value so
that the height from the nozzle to the printing platform is about the thickness of a piece of A4 paper. Return
to the previous menu, and the Z-axis compensation value will be configured.
0%
-2.30
7 Assisted Leveling (The CR Touch leveling will fail when the platform inclination is greater
than 2 mm. In this case, please use assisted leveling instead.)
-2.30
2.Turn the knob at the bottom of the hotbed and move the nozzle to the four corners of the printing
platform so that the gap between the nozzle and the printing platform is almost the thickness of a piece
of A4 paper (0.08 to 0.1 mm). Ensure that all the four corners are leveled.
Creality Slicer
Creality Slicer
The file name must only contain Latin letters Note: For details on using the software please
and digits. Chinese characters or special refer to the slicing software user manual on
symbols must not be used. the memory card.
10 Start Printing
Before printing, please check the printer again following these steps:
When the printer is powered off:
1. The nozzle is tightly connected and moves smoothly to the left and right.
2. The X axis is horizontal and stable (not wobbling up or down), and it moves run smoothly up and down.
3. The Y axis is tightly connected. The platform does not shake and moves back and forth smoothly.
4. The filament rack does not shake. The rollers are smooth. The filament extrusion is smooth.
When the printer is powered on:
1. The screen display and touch work properly. The movements of the X, Y, and Z axes are smooth.
2. The nozzle and hotbed heat up properly.
3. The feed and return of the filament works properly.
4. The leveling of the printer works properly.
Tap “Print". Select the file.
11
10 18
1
2 9 17
3
12
4 16
13
8 14 15
5
6 7
Accuracy ±0.2mm
Due to the differences between different machine models, the physical objects and the final images can differ.
The final explanation rights shall be reserved by Shenzhen Creality 3D Technology CO., Ltd.