H12 811 ENU V12.35 DataComs
H12 811 ENU V12.35 DataComs
H12 811 ENU V12.35 DataComs
Exam : H12-811-ENU
Vendor : Huawei
Version : V12.35
1
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 1
Two authentication domains "Area1" and "Area 2" are configured on a router acting as an
authentication server. If the user authenticates with the correct user name "huawei" and
password "hello", this user will be assigned In which authentication domain?
A. Authentication domain "Area 1"
B. Authentication domain "default domain" Correct
C. Authentication domain "default_admin domain"
D. Authentication domain "Area2"
Answer: B
QUESTION NO: 2
A company has 50 private IP addresses. The administrator uses NAT technology to connect
the company's network to the public network, but the company has only one public network
address and is not fixed. Which of the following NAT conversion methods meets the needs?
A. easy-ip Easy IP uses the public IP address of an interface as the translated source address
B. NAPT
C. Static NAT
D.Basic NAT
Answer: A
QUESTION NO: 3
Static NAT can only achieve one-to-one mapping between private addresses and public
addresses.
A. True Static NAT is used to do a one-to-one mapping between an inside address and an outside address.
B. False
Answer: A
QUESTION NO: 4
<huawei>system-view
[huawei]command-privilege level 3 view user save
The correct statement about the above configuration command is:
A. Modify the user's authority level to 3, and save the configuration
B. Modify the permission level of the user view command to 3, and save the configuration
C. Modify the authority level of the save command used by a user to 3
D. Modify the permission level of the save command in the user view to 3
Answer: D
QUESTION NO: 5
By default, what is the STP Forward Delay time in seconds?
A.5
B.10
C.15 (Default STP Forward delay)
D.20
2
IT Certification Guaranteed, The Easy Way!
Answer: C
QUESTION NO: 6
Which field of the ipv6 packet header can be used for QoS?
A.Traffic Class (Traffic Class is for Quality of Service)
B.Payload Length
C.Version
D.Next Header
Answer: A
QUESTION NO: 7
Complete the ACL configuration shown in the figure on the router RTA, which of the following
description is correct?
A. The VRP system will not adjust the sequence number, but will first match the rule permit
source 20.1.1.0 0.0.0.255
B. Configuration error, the sequence number of the rules must be configured from small to
large
C. The VRP system will adjust the sequence number of the first rule to 5 according to the
configuration sequence
D. The VRP system will first match the rule by numbering in sequence deny source 20.1.1.0
0.0.0.255
Answer: D
QUESTION NO: 8
As shown in the network below, all switches enable STP protocol. Disable SWA's G0/0/2 port
configuration BPDU sending function, SWC G0/0/1 re-converges to become the root port,
about this process, which of the following statements are correct? (Multiple Choice)
3
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 9
The configuration of the country code will affect the actual transmission frequency and
maximum transmission power. (Yes this can affect the frequency and transmission power)
A.True
B.False
Answer: A
QUESTION NO: 10
Which of the following networks belong to a local area network? (Multiple choice)
A. A home network
B. Office network of a company
C. Internet (WAN)
D. Broadband Metropolitan Area Network (WAN)
Answer: AB
QUESTION NO: 11
As shown in the figure below, all switches enable the STP protocol and keep other
configurations in their default state. When the network is stable, which of the following
statements are correct? (Multiple Choice)
4
IT Certification Guaranteed, The Easy Way!
Answer: AC
QUESTION NO: 12
The network shown in the figure below. The administrator hopes that RTA uses static routing,
and preferentially sends data packets to RTB 's Loopback0 interface through G0/0/1 por,
while G0/0/2 serves as a backup. So how to configure on RTA to achieve this requirement?
QUESTION NO: 13
As shown in the figure, the switch runs STP with default parameters, which of the following
ports will be elected as the designated port?
A. G0/0/1 port of switch A (STP runs on switches, by default, it is the lowest numbered interface)
QUESTION NO: 14
The output information of a switch is shown in the figure. Which of the following statements is
correct? (Multiple choice)
5
IT Certification Guaranteed, The Easy Way!
(D) (A)
(A)
A. The GE0/0/2 port of the switch carries VLAN TAG when sending VLAN20 data frames
B. The user manually created 4 VLANs
C. The GE0/0/1 port of the switch does not carry VLAN TAG when sending VLAN20 data
frames
D. The GE0/0/1 port of the switch does not carry VLAN TAG when sending VLAN10 data
frames
Answer: ABD
QUESTION NO: 15
PPPoE session can only use CHAP authentication.
A.True
B.False (PAP and CHAP)
Answer: B
QUESTION NO: 16
In order to distinguish different users and provide different network services on the AP. Which
of the following can be configured?
A.VT
B.VAP
C.VAC
D. WAP
Answer: A
QUESTION NO: 17
In the network shown in the figure below, all routers run OSPF protocol, which device is
ABR? (Multiple choice)
6
IT Certification Guaranteed, The Easy Way!
A. Router A (ABR is Area Border Router, at least connected to AREA 0 - Router A & Router B)
B. Router C
C. Router D
D. Router B
Answer: AD
QUESTION NO: 19
Which statement about OSPF protocol DR is correct?
A. DR must be the highest priority device in the network
B. Router ID, the larger the value, the more preferred to be elected as DR
C. DR election is preemptive
D. An interface priority is 0, then the interface cannot be a DR
Answer: D (DR is Designated Router, act as a central point for exchanging of
OSPF information between multiple routers on the same, multiaccess broadcast network segment)
QUESTION NO: 20
Telnet is based on TCP protocol.
A. True (Telnet uses TCP to connect to a remote system)
B. False
Answer: A
QUESTION NO: 21
What are the user authentication methods that can be deployed in wlan? (Multiple choice)
A. Portal authentication
B. MAC authentication
7
IT Certification Guaranteed, The Easy Way!
C. Radius certification
D. 802.1X authentication
Answer: ABD (Portal, MAC, 802)
QUESTION NO: 22
On the VRP platform, which of the following methods can be used to access the previous
history commands?
A. Ctr1+U
B. Ctr1+P
C. Left cursor
D. Up cursor (A simple up cursor for history of executed commands)
Answer: D
QUESTION NO: 23
The information shown in the figure is the port status information displayed on a switch
running STP. According to this information, which of the following description is wrong?
QUESTION NO: 24
Which of the following description about the Layer 2 Ethernet switch is incorrect?
A. It is necessary to make certain modifications to the layer 3 header of the forwarded
message, and then forward it (Wrong)
B. Able to learn MAC address (Correct)
C. Forward according to the Layer 2 header information of the Ethernet frame (Correct)
D. Layer 2 Ethernet switches work at the data link layer (Correct)
Answer: A
QUESTION NO: 25
In which view can the administrator modify the device name for the router?
A.User-view
B.Protocol-view
C.System-view (Similar to 'enable' in CISCO)
D.Interface-view
8
IT Certification Guaranteed, The Easy Way!
Answer: C
source MAC
QUESTION NO: 26 address
The Layer 2 Ethernet switch generates entries in the MAC address table according to the ( )
of the Ethernet frame received by the port.
A. Source IP address
B. Source MAC address
C. Destination MAC address
D. Destination IP address
Answer: B
QUESTION NO: 27
What kind of message does the OSPF protocol use to confirm the received LSU message?
A.LSU LSU - Link-State-Update
LSR - Link-State-Request
B.LSR LSA - Link-State-Advertisement
C.LSACK (Link-State-Acknowledgment)
D.LSA
Answer: C
QUESTION NO: 28
The broadcast address is a special address in which the host bits in the network address are
all set to 1, and it can also be used as a host address.
A.True
B.False (Broadcast address cannot be used as a host address)
Answer: B
QUESTION NO: 29
SNMPv1 defines 5 protocol operations.
A.True SNMPv1 specifies five core protocol data units (PDUs).
B.False
Answer: A
QUESTION NO: 30
When the IPv4 protocol is used as the network layer protocol, which field is not included in
the network layer header?
A. Source IPv4 address
B. Sequence number (Sequence Number is excluded when IPV4 protocol is used as the network layer protocol)
C. Destination IPv4 address
D. TTL
Answer: B
QUESTION NO: 31
On the VRP platform, what is the role of the command "interface vlanit <vlan-id>" ?
A. Create a VLAN
9
IT Certification Guaranteed, The Easy Way!
B. No such command
C. Create or enter VLAN virtual interface view
D. Configure VLAN for a port
Answer: C
QUESTION NO: 32
What are the advantages of the OSPF protocol? (Multiple Choice)
A. Division of support areas
B. OSPF supports load sharing for equal-cost routes (All of the above)
C. OSPF supports message authentication
D. OSPF supports type-less inter-domain routing (CIDR)
Answer: ABCD
QUESTION NO: 33
The router Radius information configuration is shown in the figure. Which of the following
statement is correct? (Multiple Choice)
(D)
(B)
A. The source IP source address of the Radius packet sent by the router is 200.0.12.2 (wrong)
QUESTION NO: 34
As shown in the figure below, the network and switch configuration information are shown in
the figure. Which of the following statements is correct? (Multiple choice)
(B)
10
IT Certification Guaranteed, The Easy Way!
(A)
QUESTION NO: 35
The network devices running the SNMP protocol are running locally-an agent process.
A.True
B.False
Answer: A
QUESTION NO: 39
11
IT Certification Guaranteed, The Easy Way!
How many types of data flows with different service levels can be marked based on MPLS
labels? (8 types of data flows based on Multi-Protocol Label Switching)
A.4
B.2
C.16
D.8
Answer: D
QUESTION NO: 40
Which of the following statements about the edge port in the RSTP protocol is correct?
A. The edge port discards the received configuration BPDU packet
B. The edge port can be directly transferred from Disable to Forwarding state
C. Edge port participates in RSTP operation
D. The interconnection ports between switches need to be set as edge ports
Answer: B Edge ports are ports of a bridge that connect to workstations or computers.
Edge ports do not register any incoming BPDU activities.
QUESTION NO: 41
Network shown below, Host A does not configure the gateway, the host B exists gateway
ARP cache, which of the following statements are correct? (Multiple choice)
A. Enable ARP proxy on the GO/0/1 port of the router, then host A can communicate with
host B
B. Host A and Host B cannot communicate in both directions (one-way communication only)
C. The data packet sent by host B with the destination IP address of 10.0.12.1 can be
forwarded to host A
D. The data packet sent by host A with the destination IP address of 11.0.12.1 can be
forwarded to host B
Answer: B
QUESTION NO: 42
Which of the following statement about static routing in Huawei equipment is wrong?
A. The cost value (Cost) of the static route cannot be modified.
B. The default value of the static route priority is 60 (This is the default value)
C. The range of the static route priority value is 1-255 (0 - 225 is wrong, maybe typo)
D. When the priority of the static route is 0, the route will definitely be preferred.
Answer: C
12
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 43
By default, network devices running SNMPv2c protocol use which of the following port
numbers to send trap messages to the network management system?
A.6
B.161
C.17
D.162 (For trap messages)
Answer: D
QUESTION NO: 44
As shown in the figure below, which of the following statement is correct?
QUESTION NO: 46
The DHCPv6 server supports providing other configuration information such as DNS server
address for the host.
A.True
B.False
Answer: A
QUESTION NO: 47
As shown in the figure, if host A and host B want to achieve inter-VLAN communication
through single-arm routing, which configuration should be done under the G0/0/1.1 interface
of RTA?
13
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 49
What is the coverage area of an AP in WLAN?
A. BSS Basic service set identifiers (BSSID)
B. SSID (Service Set IDentifier) Basic service set (BSS)
Extended service set (ESS)
C. BSSID
D.ESS
Answer: B
QUESTION NO: 50
What is the first operation performed by the FIT AP after obtaining the AC's IP address?
A. Upgrade software version
B. Download the configuration file
14
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 51
Which of the following statements about direct routing is correct?
A. Direct routing requires the administrator to manually configure the destination network and
the next-hop address
B. Direct route has lower priority than static route
C. Direct route priority is lower than dynamic route
D. Direct routing has the highest priority (Always will be)
Answer: D
QUESTION NO: 52
Which field is added to the IPv6 packet header than the IPv4 packet header?
A.Destination Address
B.Flow Label (Additional for IPv6 packet header)
C.Version
D.Source Address
Answer: B
QUESTION NO: 53 The most common values are 17 (for UDP) and 6 (for TCP)
If the transport layer protocol is UDP, the value of the network layer Protocol field is 6.
A.True
B.False
Answer: A
QUESTION NO: 54
What is the destination IP address of the DHCP DISCOER message?
A.127.0.0.1
B.224.0.0.1
C.224.0.0.2
D.255.255.255.255 The DHCP client broadcasts a DHCPDISCOVER
message on the network subnet using the destination address 255.255.255.255
Answer: D
QUESTION NO: 55
What is the port number used by the FTP protocol control plane?
A.23
B.24
C.21 (Control Plane is port 21)
D.22
Answer: C
15
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 56
The administrator plans to implement route backup by configuring static floating routes, what
is the correct way to achieve this?
A. The administrator needs to configure different metric values for the main static route and
the standby static route
B. The administrator needs to configure different TAGs for the main static route and the
standby static route
C. The administrator only needs to configure two static routes
D. The administrator needs to configure different protocol priority values for the main static
route and the standby static route (it makes sense)
Answer: D
QUESTION NO: 57
What are the characteristics of VLAN based on port?
A. Add VLAN tags to the data frame according to the IP address carried in the message
B. Assign VLAN ID according to the protocol type and encapsulation format of the data frame
C. No need to reconfigure VLAN when the host moves
D. The host mobile location needs to be reconfigured VLAN
Answer: D
QUESTION NO: 58
The basic header length of IPv6 packets is a fixed value.
A.True The fixed header starts an IPv6 packet and has a size of 40 octets (320 bits)
B.False
Answer: A
QUESTION NO: 59
As shown in the figure below, assuming the other configurations of the switch are kept in the
default state, which port of the following switch will become the designated port? (Multiple
Choice)
(B)
(D)
A. SWC's G0/0/1
B. SWA's G0/0/3
C. SWC's G0/0/2
16
IT Certification Guaranteed, The Easy Way!
D. SWB's G0/0/1
Answer: BD
QUESTION NO: 60
What is the main function of the dynamic routing protocol?
A. Manage routers
B. Generate IP address
C. Dynamically generate routing entries
D. Control router interface status
Answer: C
QUESTION NO: 61
In which working state of the STP protocol can the port be changed to the Forwarding state
without going through other states?
A. Blocking
B. Learning
C. Listening
D. Disabled
Answer: B
QUESTION NO: 62
Which statement are correct about the shortcut keys of the VRP operating platform? (Multiple
choice)
A. TAB prompts the most recently entered command
B. CTRL+C to stop the current command
C. The left cursor key (<) moves the cursor to the left position.
D.CTRL+Z back to user view
Answer: BCD
QUESTION NO: 63
Which type of message is used by network devices running SNMPv 1 protocol to actively
send alarm information?
A. Trap (for alarm information)
B. Response
C.Get Request
D. Get-Next Request
Answer: A
QUESTION NO: 64
The MAC address table of a certain switch is shown in the figure. If the switch receives a
data frame with a destination MIAC of 5489-9885-18a8 from port Eth0/0/2, which of the
following statements is correct?
17
IT Certification Guaranteed, The Easy Way!
(D)
QUESTION NO: 65
As shown in the information in the figure, when learning this switch needs to forward the
frame with the destination MAC address of 5489-98ec-f011, which of the following description
is correct?
(A)
A. The switch will flood the frame on all ports except the port that received the frame
B. The switch will send a message that the destination is unreachable to the source device
C. The switch does not find a matching entry in the MAC address table, so it will discard the
frame
D. The switch needs to send a request to discover the device with the MAC address of 5489
98ec-f011
Answer: A
QUESTION NO: 66
The switch becomes a logical switch after stacking and clustering, and Eth-Trunk across
physical devices can be deployed to improve network reliability.
A.True
B.False
Answer: A
QUESTION NO: 67
In the configuration BPDU sent by the switch, which bridge ID is unlikely to appear?
A.8192 00-01-02-03-04-CC
B.4096 00-01-02-03-04-CC
C.0 00-01-02-03-04-CC
18
IT Certification Guaranteed, The Easy Way!
D.2048 00-01-02-03-04-CC
Answer: D
QUESTION NO: 68
Which of the following OSPF protocol packets can ensure the reliability of LSA updates?
A.LSACK (For reliability of Link-State-Advertisement updates)
B.DD
C.LSU
D.LSR
Answer: A
QUESTION NO: 69
By default, in the SNMP protocol, which port number does the agent process use to send
alarm messages to NS?
A.164
B.163
C.162 (port for alarm message)
D.161
Answer: C
QUESTION NO: 71
Which of the following statements about Adjacency Segment is wrong?
A. Adjacency Segment is identified by Adjacency Segment ID (SID)
B. Adjacency Segment spreads to other network elements through IGP protocol, which is
visible globally and effective locally
C. Adjacency Segment must be configured manually (It is dynamically configured)
D. Adjacency Segment is used to identify an adjacency of a node in the network
Answer: C
19
IT Certification Guaranteed, The Easy Way!
D. On the switch, configure the port connected to the router as a Trunk port, and allow
frames of the relevant VLAN to pass
Answer: ABD
QUESTION NO: 73
The host uses the IP address 192.168.1.2 to access the Internet, which must go through
NAT.
A. TURE
B. FALSE
Answer: B
QUESTION NO: 74
In the network shown in the figure, the administrator hopes that all hosts cannot access the
web service (the port number is 80), and other services are normally accessed, so in the
interface configuration of G0/0/1, traffic-filtar outbound needs to define which ACL rule?
A. acl number 3000 rule 5 deny tcp destination-port eq www rule 10 permit ip #
B. acl number 3001 rule 5 deny udp destination-port eq www rule 10 permit ip #
C. acl number 3003 rule 5 permit ip rule 10 deny udp destination-port eq www #
D. acl number 3002 rule 5 permit ip rule 10 deny tcp destination-port eq www #
Answer: A
QUESTION NO: 75
As shown in the figure, if host A has the ARP cache of host B, host A can ping host B.
A.True
B.False
Answer: B
20
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 76
The network administrator uses Ping to test the connectivity of the network. Which of the
following protocols may be used in this process? (Multiple choice)
A.ICMP (Internet Control Message Protocol)
(User Datagram)
B.UDP
C.TCP (Transmission Control)
QUESTION NO: 77
VRP operating system commands are divided into 4 levels: access level, Monitoring level,
Configuration level, and Management level. Which level can run various business
configuration commands but cannot operate the file system?
A. Configuration level
B. Monitoring level
C. Access level
D. Management level
Answer: A
QUESTION NO: 78
When the switch port sends a data frame carrying the same VLAN TAG and PVID, it must
strip the VLAN TAG and forward it.
A.True
B.False
Answer: B
QUESTION NO: 79
Which of the following commands can be used to view the router's CPU usage?
A.display cpu-state
B.display interface
C.display memory
D.display cpu-usage
Answer: D
QUESTION NO: 80
The router running the OSPF protocol reaches the FULL state first, and then synchronizes
the LSDB. (Link-State-Database)
A. True
B. False
Answer: B
QUESTION NO: 81
At present, the company has a network administrator, and the AR2200 in the company
21
IT Certification Guaranteed, The Easy Way!
network can be remotely managed by directly entering the password through Telnet. After the
two new network administrators arrived, the company hopes to assign their own user names
and passwords to all administrators, as well as different levels of authority. So how should it
be done? Multiple choices
A. Each administrator uses a different public IP address of the device when running the
Telnet command
B. The user authentication mode configured by Telnet must select AAA mode
C. When configuring each administrator's account, different permission levels need to be
configured
D. Configure three user names and their corresponding passwords in the AAA view
Answer: BCD
QUESTION NO: 82
The Priority field in the VLAN tag can identify the priority of the data frame. What is the range
of this priority?
A.0-15
B.0-63
C.0-3
D.0-7 (0 - best effort to 7- highest)
Answer: D
QUESTION NO: 83
Which of the following statements about VLANIF interfaces are correct?
A. VANIF interface does not need to learn MAC address
B. VLANTF interface has no MAC address
C. Different VLANIF interfaces can use the same IP address
D. VLANIF interface is a three-layer interface
Answer: D
QUESTION NO: 84
In a Layer 2 network with redundant links, which of the following protocols can be used to
avoid loops?
A. VRRP
B.ARP
C.UDP
D. STP (Spanning Tree Protocol)
Answer: D
QUESTION NO: 85
The routing table is shown in the figure. Which of the following statements is correct?
(Multiple choice)
22
IT Certification Guaranteed, The Easy Way!
A. The router forwards data packets with the destination IP address 10.0.3.3 from
Ethernet0/0/0
B. Router from Ethernet0/0/0 forwarding destination IP address 10.0.2.2 packet
C. The router forwards data packets with the destination IP address 10.0.12.1 from
Ethernet0/0/0
D. The NextHop of the destination network 10.0.3.3/32 is not directly connected, so the router
will not forward packets with the destination IP address of 10.0.3.3.
Answer: ABC
QUESTION NO: 86
There are multiple route entries to the same destination network in the routing table. These
routes are called:
A. Sub-optimal routing
B. Multi-path routing
C. Default route
Equal-cost multi-path routing (ECMP) is a routing strategy
D. Equal cost routing where packet forwarding to a single destination can occur
over multiple best paths with equal routing priority.
Answer: D
QUESTION NO: 87
For the description of the PPP link establishment process, which of the following statement is
wrong?
A. In the Establish phase, the PPP link performs LCP parameter negotiation. The negotiation
content includes the maximum receiving unit MRU, authentication method, magic word and
other options.
B. After the NCP negotiation is successful, the PPP link will maintain the communication
state and enter the Terminate phase.
C. The Dead phase is also called the physical layer unavailable phase. When the two ends of
the communication detect that the physical line is activated, they will migrate from the Dead
phase to the Establish phase, which is the link establishment phase.
D. In the Network phase, the PPP link performs NCP negotiation. Select and configure a
network layer protocol through NCP negotiation, and negotiate network layer parameters
E. PPP link supports half-duplex and full-duplex modes
Answer: B
QUESTION NO: 88
23
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 89
Which of the following methods can read data non-blocking in Python's telnetlib?
A.telnet_Read_all
B.telnet_read_very_lazy
C.telnet._read_eager
D.telnet_read _very_eager
Answer: C
QUESTION NO: 90
Which parameter is used in the spanning tree protocol for root bridge election?
A. Port ID
B. Bridge priority You can manipulate the Root Bridge Election by setting Bridge priority on your switches.
C. Root path cost
D. Bridge ID
Answer: B
QUESTION NO: 91
What elements can NAPT convert?
A. MAC address + port number
B. Only IP address
Network address port translation (NAPT) is a technique in which
C. IP address + port number port numbers and private Internet Protocol (IP) addresses are mapped
from multiple internal hosts to one public IP address.
D. Only MAC address
Answer: C
QUESTION NO: 92
On Huawei routers, what is the default value of the OSPF protocol internal routing priority?
A.20
B.10 An OSPF route has an internal preference of 10
C.30
D.0
Answer: B
QUESTION NO: 93
On Huawei equipment, if you use aaa authentication for authorization. When the remote
server does not respond, you can authorize from the network equipment side.
A.True
24
IT Certification Guaranteed, The Easy Way!
B.False
Answer: A
QUESTION NO: 94
Which of the following attributes cannot be used as a parameter to measure Cost? (Multiple
choice)
A. Bandwidth
B. Sysname
C. Delay
D. Hop count
Answer: BC
QUESTION NO: 95
As shown in the following figure, router A and router B establish an OSPF neighbor
relationship. The OSPF process number of router A is 1, and the area number is 0. Which of
the following configurations on router A can enable router B to obtain the network segment of
host A routing? (Multiple choice)
QUESTION NO: 96
In IPv4 networks, AP supports static and DHCP methods to obtain IP addresses.
A.True (Yes, Acces Points can support both)
B.False
Answer: A
QUESTION NO: 97
The correct description of the information as shown in the figure is ().
[R1]display interface go/0/o
25
IT Certification Guaranteed, The Easy Way!
QUESTION NO: 98
If the value of the Type/Length field of an Ethernet data frame is 0 x 0800, the length of the
upper layer message header carried by this data frame is in the range of 20-60B.
A.TRUE
B.False
Answer: A
QUESTION NO: 99
The configuration information of a interface of the router is shown in the figure, then which
VILAN data packet can this port receive?
interface Gigabit Ethernet 0/0/2.30
dot1q terainat1on vid 100 (B)
ip address 1o.o.21.1 255.255.255.0
arp broadcast enable
A.1
B.100
C.30
D.20
Answer: B
26
IT Certification Guaranteed, The Easy Way!
In the network shown in the figure below, all links are Ethernet links, and all interfaces of all
routers run OSPF protocol, how many DRs are elected in the entire network?
(Direct Routes)
A.4
B.1
C.3
D.2
Answer: A
27
IT Certification Guaranteed, The Easy Way!
A. The G0/0/1 port of the switch has disabled MAC address learning
B. SWA turns off the MAC address learning function of the VLAN to which host A belongs
28
IT Certification Guaranteed, The Easy Way!
29
IT Certification Guaranteed, The Easy Way!
Which of the following statements about the division of OSPF protocol area is wrong?
A. Area 0 is the backbone area, and other areas must be connected to this area
B. The LSDBs in the routers in the same OSPF area are completely consistent
C. Dividing OSPF areas can reduce the LSDB scale of some routers
D. Only ABR can be used as ASBR
Answer: D
30
IT Certification Guaranteed, The Easy Way!
31
IT Certification Guaranteed, The Easy Way!
32
IT Certification Guaranteed, The Easy Way!
B.False
Answer: B
33
IT Certification Guaranteed, The Easy Way!
B. Transport layer
C. Application layer
D. Network layer (Router in at the Network Layer)
Answer: D
A. The router will discard data packets whose destination network is 11.0.0.0/8
B. The router will forward data packets whose destination network is 12.0.0.0/8
C. The data packet whose destination network is 11.0.0.0/8 will be forwarded from the
router's GigabitEthernet0/0/0 interface
D. The data packet whose destination network is 12.0.0.0/8 will be forwarded from the
router's Ethernet070/0 interface
Answer: BC
34
IT Certification Guaranteed, The Easy Way!
A.time-range am9topm5 08:00 to working-day Acl number 2003 rule 5 deny time-range
am9topjni5
B.time-range am9topm5 08:00 to 17:00 off-day # acl number 2004 rule 5 permit time-range
C. time-range am9topm5 08:00 to 17:00 daily acl number 2001 rule 5 deny time-range
am9topm5
D.time-range am9topm5 07:00 to 18:00 daily Acl number 2002
Answer: C
35
IT Certification Guaranteed, The Easy Way!
D. RTA will continue to receive, analyze and process OSPF packets sent by RTB
Answer: BCD
36
IT Certification Guaranteed, The Easy Way!
A.SWC G0/0/1
B.SWC G0/0/2
C.SWB G0/0/3
D.SWA G0/0/3
Answer: A
37
IT Certification Guaranteed, The Easy Way!
A.1
B.2
C.3
D.4
38
IT Certification Guaranteed, The Easy Way!
Answer: C
39
IT Certification Guaranteed, The Easy Way!
B. Current configuration
C. New configuration
D. Default parameters
Answer: D
40
IT Certification Guaranteed, The Easy Way!
In the VRP interface, use the command startup saved-configuration backup.cfg to configure
the startup.cfg file for the next startup.
A. TURE
B. FALSE
Answer: A
41
IT Certification Guaranteed, The Easy Way!
42
IT Certification Guaranteed, The Easy Way!
A. The authentication method adopted by the domain with the domain name huawei is local
ID
B. The authorization method for the domain with the domain name huawei is local
authorization
C. Use the username huawei for authentication, the password needs to be 654321
D. The domain with the domain name huawei does not use the billing plan
Answer: BD
43
IT Certification Guaranteed, The Easy Way!
Answer: A
A.True
B.False
Answer: A
44
IT Certification Guaranteed, The Easy Way!
A.True
B.False
Answer: B
45
IT Certification Guaranteed, The Easy Way!
46
IT Certification Guaranteed, The Easy Way!
C.5GHz
D.6GHz
Answer: BC
47
IT Certification Guaranteed, The Easy Way!
In the WLAN architecture, the FIT AP cannot work independently and needs to be managed
by the AC. Which of the following protocols are used to communicate between FIT AP and
AC?
A. IPsec
B.WEP
C.CAPWAP
D.WAP
Answer: C
A.SWC
B.SWA
C.SWB
D.SWD
Answer: B
48
IT Certification Guaranteed, The Easy Way!
A. TRUE
B. False
Answer: B
A. The following entries may exist in the ARP cache of host A, 10.0.12.2 MAC-C
B. The router needs to be configured with static routing, otherwise host A and host B cannot
communicate in both directions
C. The following entries exist in the ARP cache of host A 11.0.12.1 MAC-B
D. Host A and Host B can communicate in both directions
Answer: AD
49
IT Certification Guaranteed, The Easy Way!
Answer: B
50
IT Certification Guaranteed, The Easy Way!
51
IT Certification Guaranteed, The Easy Way!
192.168.1.255.
A.True
B.False (Not sure, what is the network mask?)
Answer: B
52
IT Certification Guaranteed, The Easy Way!
A.True
B.False
Answer: A
53
IT Certification Guaranteed, The Easy Way!
forwarding method of OpenFlow switches is based on flow table forwarding. Which of these
two forwarding methods are correct? (Multiple Choice)
A. The routing table is of fixed length. A device can only have one public routing table
B. The flow table is variable length. A network device can only have one flow table
C. The matching method of the flow table is to match the MAC address and IP address of the
traffic at the same time
D. The matching method of the address table is to match the route of the destination network
segment with the longest mask
Answer: ACD
A. MAC-B,11.0.12.1
B. MAC-D,11.0.12.1
C. MAC-C,10.0.12.2
D. MAC-A,11.0.12.1
Answer: B
54
IT Certification Guaranteed, The Easy Way!
links, and the two links are aggregated in manual load sharing mode. The aggregated port
number is 1, and the aggregated link performs data when forwarding, you need to carry
VLAN TAG 100. Switch A uses Trunk link. Which of the following configurations should be
used for Switch A?
A.
B.
55
IT Certification Guaranteed, The Easy Way!
C.
D.
Answer: B
56
IT Certification Guaranteed, The Easy Way!
(Multiple Choice)
A. The default VLAN cannot be deleted manually
B. By default, all ports of the switch are member ports of the default VLAN
C. A default VLAN must be created before it can be assigned a port
D. The IP address configured on the switch will only be applied to the member ports of the
default VLAN
Answer: ABD
A. Client3 belongs to VLAN30, and the command for dividing VLAN on the switch is correct
B. Client4 belongs to VLAN40, and the command for dividing VLAN on the switch is correct
C. Client2 belongs to VLAN20, and the switch based on the MAC address division command
is correct
D. Client1 belongs to VLAN10, and the command for dividing VLAN on the switch is correct
Answer: BCD
57
IT Certification Guaranteed, The Easy Way!
A. G0/0/1 of switch B
B. G0/0/1 of switch A
C. HUB's G0/0/3
D. G0/0/2 of switch A
Answer: D
58
IT Certification Guaranteed, The Easy Way!
A.Router D
B.Router B
C.Router C
D.Router A
Answer: D
59
IT Certification Guaranteed, The Easy Way!
60
IT Certification Guaranteed, The Easy Way!
B. False
Answer: B
61
IT Certification Guaranteed, The Easy Way!
62
IT Certification Guaranteed, The Easy Way!
63
IT Certification Guaranteed, The Easy Way!
A.TRUE
B.False
Answer: A
64
IT Certification Guaranteed, The Easy Way!
65
IT Certification Guaranteed, The Easy Way!
A.True
B.False
Answer: B
66
IT Certification Guaranteed, The Easy Way!
B. Multicast
C. Network
D. Host
Answer: A
A. The saved configuration file will be replaced by the running configuration file
B. If the user wants to clear the next startup configuration file of the device configuration, then
should select "N"
C. If the user wants to clear the next startup configuration file of the device configuration, then
67
IT Certification Guaranteed, The Easy Way!
68
IT Certification Guaranteed, The Easy Way!
B. 192.168.176.0/25
C. 192.168.176.96/27
D. 192.168.176.48/29
Answer: A
69
IT Certification Guaranteed, The Easy Way!
70
IT Certification Guaranteed, The Easy Way!
A. MAC-C, 11.0.12.1
B. MAC-D, 10.0.12.2
C. MAC-D, 11.0.12.1
D. MAC-B, 11.0.12.1
71
IT Certification Guaranteed, The Easy Way!
Answer: C
A.4.6
B.1.4.5.6
C.4.5.6
D.1.4.6
Answer: D
72
IT Certification Guaranteed, The Easy Way!
73
IT Certification Guaranteed, The Easy Way!
value of the Cost value, then the path for RTA to reach the network 10.0.0.0/8 is:
A.A-B-D
B.RTA cannot reach 10.0.0.0/8
C.A-C-D (Open Shortest Path First)
D.A-D
Answer: C
74
IT Certification Guaranteed, The Easy Way!
B.False
Answer: A
75
IT Certification Guaranteed, The Easy Way!
Answer: C
76
IT Certification Guaranteed, The Easy Way!
C.SNMPv1
D.SNMPv2
Answer: A
77
IT Certification Guaranteed, The Easy Way!
A.172.16.1.0/24
B.192.17.0.0/24
C.172.18.0.0/16
D.172.16.1.1/32
Answer: CD
A. next system startup file system can use the command "startup system software <startup-
software-name>" to modify
78
IT Certification Guaranteed, The Easy Way!
79
IT Certification Guaranteed, The Easy Way!
Answer: B
80
IT Certification Guaranteed, The Easy Way!
81
IT Certification Guaranteed, The Easy Way!
A.GE0/0/2
B.GE0/0/5
C.GE0/0/3
D.GE0/0/4
Answer: B
82
IT Certification Guaranteed, The Easy Way!
A. When the switch restarts, the MAC address learned by port Eth0/0/2 does not need to be
relearned
B. When the switch restarts, the MAC address learned by port Eth0/0/3 needs to be learned
again
C. The data frame with the source MAC address of 5489-9811-0b49 and the destination MAC
83
IT Certification Guaranteed, The Easy Way!
address of 5489-9894-1d30 received from the port is forwarded from the Eth0/0/2 port
D. The data frame with the source MAC address of 5489-9885-18a8 and the destination
MAC address of 5489-989d-1d30 received from the port is forwarded from the Eth0/0/1 port
Answer: D
84
IT Certification Guaranteed, The Easy Way!
Which of the following statements about RA and RS in IPv6 are correct? (Multiple Choice)
A. RS is used to reply address prefix information
B. RA is used to request address prefix information
C. RS is used to request address prefix information
D. RA is used to reply address prefix information
Answer: CD
85
IT Certification Guaranteed, The Easy Way!
A.True
B.False
Answer: A
86
IT Certification Guaranteed, The Easy Way!
A. G0/0/1
B. G0/0/3
C. G0/0/0
D. G0/0/2
Answer: B
87
IT Certification Guaranteed, The Easy Way!
In order to implement the FIT AP online, the FIT AP first needs to obtain the IP address of the
AC. Which of the following is not included in the method of obtaining the IP address of the AC
by the FIT AP?
A. Broadcasting method
B. Static designation method on AP
C. Multicast mode
D. DHCP Option mode
Answer: A
C.20B
D.64B
Answer: D
88
IT Certification Guaranteed, The Easy Way!
89
IT Certification Guaranteed, The Easy Way!
90
IT Certification Guaranteed, The Easy Way!
B.False (It overlaps significantly, Channels 1, 6, and 11, however are far enough)
Answer: B
91
IT Certification Guaranteed, The Easy Way!
A. about 3 seconds
B. about 50 seconds
C. about 30 seconds
D. about 15 seconds
Answer: B
92
IT Certification Guaranteed, The Easy Way!
93
IT Certification Guaranteed, The Easy Way!
Answer: A
94
IT Certification Guaranteed, The Easy Way!
B.False
Answer: B
95
IT Certification Guaranteed, The Easy Way!
96
IT Certification Guaranteed, The Easy Way!
A. acl number 2000 rule 5 deny source 100.0.12.0 0.0.0.255 rule 10 permit source
97
IT Certification Guaranteed, The Easy Way!
98
IT Certification Guaranteed, The Easy Way!
A.70
B.100
C.20
D.60
Answer: D
99
IT Certification Guaranteed, The Easy Way!
B.Local
C.None
D.HWTACACS
Answer: BCD
A. Choose the second item as the best matching item, because the cost of the RIP protocol
is small
B. Select the second item as the best matching item, because the route is a more accurate
match relative to the destination 9.1.4.5
C. Choose the second item as the best match, because Ethernet0 is faster than serial0
D. Select the first item as the best matching item, because the priority value of the ospf
protocol is higher
Answer: B
100
IT Certification Guaranteed, The Easy Way!
101
IT Certification Guaranteed, The Easy Way!
C. The port will build a MAC address table based on the received user traffic, but does not
forward user traffic.
D. The port not only does not process BPDU packets, but also does not forward user traffic.
Answer: A
102
IT Certification Guaranteed, The Easy Way!
A.Attempt
B.2-way
C.Fu11
D.Down
Answer: B
103
IT Certification Guaranteed, The Easy Way!
D. Network layer
Answer: D
104
IT Certification Guaranteed, The Easy Way!
A.GigabitEthernet 0/0/3
B.GigabitEthernet0/0/2
C.Eth-Trunk 1
D.GigabitEthernet0/0/1
Answer: C
105
IT Certification Guaranteed, The Easy Way!
distributed control
Answer: ACD
106
IT Certification Guaranteed, The Easy Way!
107
IT Certification Guaranteed, The Easy Way!
A.acl rumber 300o rule 5 deny ospf rule 10 deny icmp # interface GigabitEthernet0/0/1 traffic-
filter inbound ac1 300o #
B.acl rumber 2000 rule 5 deny 89 rule 10 deny 1 # interface GigabitEtherneto/0/1 traffic-filter
inbound ac1 2000 #
C.acL rumber 300o rule 5 deny 89 rule 10 deny icmp # interface GigabitEthernet0/0/1 traffic-
filter inbound ac1 30oo #
D.acl number 3000 rule 5 deny 89 rule 10 deny 1 interface GigabitEtherneto/0/1 traffic-filter
inbound aci 3000
Answer: ACD
108
IT Certification Guaranteed, The Easy Way!
C. CPE
D. AP
Answer: ABD
109
IT Certification Guaranteed, The Easy Way!
C. set-request message
D. get-request message
Answer: A
A. The network between RTA and SWC is the same conflict domain
B. The network between SWA and SWC is the same conflict domain
C. The network between SWA and SWB is the same broadcast domain
D. The network between SWA and SWC is the same broadcast domain
Answer: B
110
IT Certification Guaranteed, The Easy Way!
D.OSPF
Answer: B
(B) (B)
111
IT Certification Guaranteed, The Easy Way!
Answer: A
A. Host C cannot be assigned a public network address and cannot access the public
network
112
IT Certification Guaranteed, The Easy Way!
B. All hosts can access the public network by using the public network address in turn
C. RTA converts the source port of host C, and host C can access the public network
D. RTA assigns the interface address (200.10.10.3) to host C, host C can access the public
network
Answer: C
113
IT Certification Guaranteed, The Easy Way!
114
IT Certification Guaranteed, The Easy Way!
A.True
B.False (No, It is failed proof)
Answer: B
115
IT Certification Guaranteed, The Easy Way!
Answer: ABC
116