BS en ISO 11114-2 - Compatibility of Materials
BS en ISO 11114-2 - Compatibility of Materials
BS en ISO 11114-2 - Compatibility of Materials
National foreword
This British Standard is the UK implementation of
EN ISO 11114-2:2013. It supersedes BS EN ISO 11114-2:2001,
which is withdrawn.
The UK participation in its preparation was entrusted to
Technical Committee PVE/3, Gas containers.
A list of organizations represented on this committee can be
obtained on request to its secretary.
This publication does not purport to include all the necessary
provisions of a contract. Users are responsible for its correct
application.
© The British Standards Institution 2013.
Published by BSI Standards Limited 2013.
ISBN 978 0 580 68976 5
ICS 23.020.30; 23.060.40
Compliance with a British Standard cannot confer immunity
from legal obligations.
This British Standard was published under the authority of the
Standards Policy and Strategy Committee on 30 April 2013.
Amendments issued since publication
Date Text affected
EUROPEAN STANDARD EN ISO 11114-2
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2013
English Version
Bouteilles à gaz - Compatibilité des matériaux des Gasflaschen - Verträglichkeit von Flaschen- und
bouteilles et des robinets avec les contenus gazeux - Partie Ventilwerkstoffen mit den in Berührung kommenden Gasen
2: Matériaux non métalliques (ISO 11114-2:2013) - Teil 2: Nichtmetallische Werkstoffe (ISO 11114-2:2013)
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11114-2:2013: E
worldwide for CEN national Members.
BS EN ISO 11114-2:2013 EN ISO 11114-2:2013 (E)
Foreword
This document (EN ISO 11114-2:2013) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat
of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2013, and conflicting national standards shall be withdrawn at
the latest by October 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11114-2:2013 has been approved by CEN as EN ISO 11114-2:2013 without any modification.
3
BS EN ISO 11114-2:2013
ISO 11114-2:2013(E)
Contents Page
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11114-2 was prepared by Technical Committee ISO/TC 58, Gas cylinders, in collaboration with
Technical Committee CEN/TC 23, Transportable Gas cylinders in accordance with the Agreement on
technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition, Clauses 4 and 6, and Table 1 of which have been
technically revised. Annex A has been deleted.
ISO 11114 consists of the following parts, under the general title Gas cylinders — Compatibility of cylinder and
valve materials with gas contents:
— Part 4: Test methods for selecting metallic materials resistant to hydrogen embrittlement.
Introduction
This part of ISO 11114 deals with the compatibility of non-metallic materials used for gas cylinders and gas
cylinder valves with the gas contents of the cylinder. Compatibility of metallic materials is treated in
ISO 11114-1.
Non-metallic materials are very often used for the construction of gas cylinder valves as seals, e.g. o-ring,
gland packing, seats, or as lubrication products to avoid friction. They are also commonly used to ensure
sealing of the valve/cylinder connection. For gas cylinders, they are sometimes used as an internal coating or
as a liner for composite materials.
Non-metallic materials not in contact with the gas are not covered by this part of ISO 11114.
This part of ISO 11114 is based on current international experience and knowledge. Some data are derived
from experience involving a mixture of the gas concerned with a dilutant, where no data for single component
gases were available.
This part of ISO 11114 has been written to be in conformity with the UN Recommendations on the Transport
of Dangerous Goods: Model Regulations. When published it will be submitted to the UN Sub Committee of
Experts on the Transport of Dangerous Goods with a request that it be included in the Model Regulations.
Where there is any conflict between this part of ISO 11114 and any applicable regulation, the regulation
always takes precedence.
1 Scope
This part of ISO 11114 gives guidance in the selection and evaluation of compatibility between non-metallic
materials for gas cylinders and valves and the gas contents. It also covers bundles, tubes and pressure
drums.
This part of ISO 11114 can be helpful for composite and laminated materials used for gas cylinders.
It does not cover the subject completely and is intended to give guidance only in evaluating the compatibility of
gas/material combinations.
Only the influence of the gas in changing the material and mechanical properties is considered (for example
chemical reaction or change in physical state). The basic properties of the materials, such as mechanical
properties, required for design purposes are normally available from the materials supplier and are not
considered in this part of ISO 11114.
The compatibility data given are related to single component gases but can be used to some extent for gas
mixtures. Ceramics, glasses, and adhesives are not covered by this part of ISO 11114.
This part of ISO 11114 is not intended to be used for cryogenic fluids (see ISO 21010).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 11114-3, Transportable gas cylinders — Compatibility of cylinder and valve materials with gas
contents — Part 3: Autogenous ignition test for non-metallic materials in oxygen atmosphere
ISO 10297, Gas cylinders — Refillable gas cylinder valves — Specification and type testing
3.1
competent person
person who has the necessary technical knowledge, qualification, experience and authority to assess and
approve materials for use with gases and to define any special conditions of use that are necessary
3.2
acceptable
material/gas combination that is satisfactory under normal conditions of use (as defined in Clause 5), provided
that any indicated non-compatibility risks, as given in Table 1, are taken into account
3.3
not acceptable
material/single gas combination that is not safe under normal conditions of use (as defined in Clause 5)
3.4
dynamic sealing
where in normal operation the non-metallic material is used to provide a pressure seal between two surfaces
that have relative motion to each other
3.5
static sealing
where in normal operation the non-metallic material is used to provide a pressure seal between two surfaces
that have not relative motion to each other
4 Materials
4.1 General
Non-metallic materials shall be suitable for the intended service. They are suitable if their compatibility is
stated as acceptable in Table 1, or the necessary properties have been proved by tests or long and safe
experience to the satisfaction of a competent person.
If coated materials are used the suitability of the combination shall be assessed and approved if all technical
aspects have been considered and validated by a competent person. These technical aspects include but are
not limited to compatibility of the coating material with the intended gas, durability of the coating during all its
intended use and gas permeability through it.
The most commonly used non-metallic materials for gas cylinders and cylinder valves can be grouped as
follows:
plastics;
elastomers;
— fluid lubricants.
a) Plastics:
Polytetrafluoroethylene (PTFE);
Polychlorotrifluoroethylene (PCTFE);
Polyvinylidenefluoride (PVDF);
Polyamide (PA);
Polypropylene (PP);
Polyetheretherketone (PEEK);
Polyimide (PI);
Polyoxymethylene (POM).
b) Elastomers:
c) Fluid lubricants:
Hydrocarbon (HC);
Fluorocarbon (FC).
5 General considerations
It is important to note that these materials are generic types. Within each material type there are variations in
the properties of the materials due to polymer differences and formulations used by manufacturers to modify
physical and chemical properties of the material. The user of the material should therefore consult the
manufacturer and if necessary carry out tests before using the material (for example for critical services such
as oxygen and other oxidizing gases).
Lubricants are often used in valves to reduce friction and wear in the moving parts. For valves used for
oxidizing gases or for gases supporting combustion, if lubrication is required, it shall be ensured that the
lubricant is compatible for the intended application when the lubricated components are in contact with the
oxidizing gas or the gas supporting combustion.
Where the lubricant is listed as "not acceptable" in Table 1 for reasons other than violent reaction (F), it may
be used safely and usually satisfactorily in applications which do not involve contact in normal operation with
the gas. An example of such an application is the lubrication of the valve actuating mechanism not in contact
with the gas.
Where the lubricant is listed as "not acceptable" for the reason of violent reaction (F), it should not be used in
any part of the system that can be contacted by the gas, even under abnormal conditions such as in the event
of a failure of the gas sealing system. If there is a risk of violent reaction, appropriate safety and suitability
tests shall have been carried out for the lubricant application before it is used either on the lubricant itself, as
specified in ISO 11114-3, or on the lubricated equipment in which it will be used, as specified in ISO 10297.
The properties of plastics and elastomers including compatibility are dependent on temperature. Low
temperature can cause hardening and the possibility of embrittlement, whereas high temperature can cause
softening and the possibility of material flow. Users of such materials shall check to ensure their suitability
over the entire operating temperature range specified by the cylinder and valve manufacturing standards.
Some materials become brittle at low temperatures, especially at temperatures at the lower end of the normal
operating range (e.g. fluorocarbon rubber). Temperatures in the refrigerant or cryogenic ranges affect many
materials and caution shall be exercised at temperatures below -50° C. This risk shall be considered in
particular when transfilling by thermal siphoning at low temperature or similar procedures, or for cylinders
regularly filled at low temperatures (e.g. CO2).
6 Specific considerations
6.1 General
The compatibility of gases with non-metallic materials is affected by chemical reactions and physical
influences, which can be classified as follows.
6.2.1.1 Principle
Historically the majority of serious accidents from rapid oxidation or violent combustion have occurred with
oxidizing gas supporting combustion at high pressure. Thorough investigation of all materials and factors
should be conducted with great care and all data should be considered before designing or using equipment
to handle oxidizing gases or gases supporting combustion.
Compatibility depends mainly on the operating conditions (pressure, temperature, gas velocity, particles,
equipment design, and application). The risk shall particularly be considered with gases such as oxygen,
fluorine, chlorine and nitrogen trifluoride. Most of the non-metallic materials can be ignited relatively easily
when in contact with oxidizing gases (see ISO 10156) and even when in contact with gases not classified as
oxidizing but still supporting combustion.
The selection of a material for use with oxygen and/or an oxygen enriched atmosphere is primarily a matter of
understanding the circumstances that cause the material to react with oxygen. Most materials in contact with
oxygen will not ignite without a source of ignition energy (e.g. friction, heat of compression, particle impacts,
etc.). When an energy input rate, as converted to heat, is greater than the rate of heat dissipation, and the
resulting heat increase is continued for sufficient time, ignition and combustion will occur.
a) the materials compatibility properties (ease of ignition and energy of combustion); and
b) the different energy sources that will produce a sufficient increase in the temperature of the material.
These general factors should be viewed in the context of the entire system design so that the specific factors
listed below will assume the proper relative significance.
the properties of the materials, which include the factors affecting ease of ignition and the conditions
affecting potential resulting damage (heat of reaction),
the operating conditions: e.g. pressure, temperature, oxygen and/or oxidizing gas concentrations in a gas
mixture, influence of dilutant (e.g. helium), surface contamination,
the potential sources of ignition (e.g. friction, heat of compression, heat from mass impact, heat from
particle impact, static electricity, electrical arc, resonance, internal flexing),
possible consequence (e.g. effects on the surroundings such as propagation of fire), and
In conclusion the evaluation of compatibility of non-metallic materials is more critical than that of metallic
materials, which generally perform well when in contact with oxygen.
In accordance with 6.2.1.1, it is not possible to make a simple statement concerning the compatibility of non-
metallic materials with oxidizing gases such as oxygen, chlorine, nitric oxide, nitrous oxide, nitrogen dioxide,
nitrogen trifluoride, etc. (see ISO 10156).
For fluorine, which is the most oxidizing gas, all non-metallic materials would historically fall into the
classification "not acceptable".
For fluorine mixtures the gases industry now has evidence of successful testing and safe history of use of
PTFE and PCTFE under controlled conditions (e.g. low concentration and low pressure). Therefore following
an assessment and authorisation by a competent person, these materials are acceptable in similar conditions.
Oxygen and other oxidizing gases can react violently when tested with all non-metallic materials listed in 4.2
a), 4.2 b) and 4.2 c). Some materials such as PTFE and FKM are more resistant to ignition than other plastics
and elastomers. HC lubricants are normally not acceptable. Under certain conditions other plastics and
elastomers listed can be safely used in oxidizing service without presenting some of the disadvantages of
PTFE, i.e. poor mechanical properties, and risk of release of toxic products for breathing gas applications, see
ISO 15001, or FKM, i.e. swelling, poor mechanical properties at low temperature, risk of release of toxic
products in breathing gas applications, etc..
Consequently, non-metallic materials may only be used if it has been proven by tests (or long and safe service
experience), taking into account all the operating conditions and especially the design of the equipment, that
their use is safe. ISO 11114-3 and ISO 21010 give testing methods for polymeric materials and fluid lubricants
that will result in conservative value. Some non-metallic material can be safely used at higher pressure when
they are tested in the final design configuration, e.g. in gas cylinder valves and regulator. Cylinder valves shall
be tested according to ISO 10297 for oxygen service.
6.2.2.1 Extraction
Solvent extraction of plasticizers from elastomers can cause shrinkage, especially in highly plasticized
products.
Some solvents, e.g. acetone or DMF 1) used for dissolved gases such as acetylene, can damage non-metallic
materials.
Some non-metallic materials can be chemically attacked by gases. This attack can sometimes lead to the
complete destruction of the material, e.g. the chemical attack of silicone elastomer by ammonia.
Elastomers and plastics may be subject to swelling due to gas (or liquid) absorption. This can lead to an
unacceptable increase of dimensions (especially for O-rings) or the cracking due to sudden out-gassing when
the partial pressure is decreased, e.g. carbon dioxide with fluorocarbon.
Initial swelling can be masked by subsequent extraction of plasticizers and fillers while in service. Other
important effects such as changes in mechanical strength and hardness should also be considered.
Differences in the compounding, formulation and curing of a given elastomer can cause significant differences
in the swelling of the material in service.
Regardless of the above compatibility evaluation, the design configuration (e.g. static or dynamic sealing)
shall be taken into account before deciding to use elastomers or plastics. In this part of ISO 11114, a swelling
of more than approximately 15 % in normal service conditions is marked N (not acceptable for dynamic
sealing); a swelling less than this is marked A (acceptable) provided other risks are also acceptable.
NOTE There is also a risk of cross bonding between sulphur vulcanised rubbers and copper alloys.
Gases can lead to an unacceptable change of mechanical properties in some non-metallic materials. This can
result, for example, in an increase in hardness or a decrease in elasticity. ISO 1817 gives testing methods to
check the influence of the gas on the mechanical properties.
Some gases contain typical impurities which may not be compatible with the intended materials (e.g. acetone
in acetylene, hydrogen sulphide in methane).
Some materials become contaminated in toxic gas use by the toxic gas and become hazardous themselves
(e.g. during maintenance of equipment).
Many materials when subjected to extreme conditions (such as elevated temperature) can release dangerous
products (e.g. toxic products). This risk shall be considered in particular for breathing gases as specified in
ISO 15001.
1) Dimethylformamide.
Ageing is a gradual change in the mechanical and physical properties of the material due to the environment
in which it is used or stored. Many elastomer and plastic materials are particularly subject to ageing; some
gases like oxygen and in general exposure to high temperatures may accelerate the ageing process, leading
to degradation such as cracking, brittleness, etc.
The permeation of some gases (e.g. helium, hydrogen, carbon dioxide) through non-metallic material can be
significant. For a given material, the permeation rate mainly depends on temperature, pressure, thickness,
and surface area of the material in contact with the gas. The molecular radius of the gas and the specific
formulation of plasticizers and other additives can cause a wide range of permeation rates for a particular type
of plastic or elastomer.
This risk shall be considered for effects to the surroundings (e.g. toxicity, fire potential).
7 Compatibility data
Table 1 lists the gases in alphabetic order with the UN number in bracket. In this table, the compatibility data
is given using the symbols and abbreviations defined in 7.2.1 and 7.2.2. When a gas/material combination is
not acceptable, the main reason is given, using the appropriate abbreviation for the non-compatibility risk (see
6.2). The abbreviations are also sometimes used for acceptable combinations to show a limited risk.
If no UN number is listed in the table for a gas (or a liquid), this means that this gas has no official UN number
but it may be transported using a generic NOS (Not Otherwise Specified) number (e.g. compressed gas,
flammable, NOS, UN 1954).
— literature data;
— laboratory tests.
The resistance to gases can be estimated by simple immersion tests in the respective gas with approximately
the same or intensified exposure conditions (increase of temperature, pressure or flow rate). Time- and
equipment-consuming test methods to evaluate the permeation, the absorption as well as the resistance to
stress cracking are required in many cases.
Apart from the visual evaluation of detectable changes, changes in weight and dimension as well as the
course of mechanical and other physical characteristics, depending on the immersion time are the parameters
of immersion tests. They are consulted as classification characteristics.
In literature and company leaflets frequently used classifications are “resistant”, "conditionally resistant" and
"not resistant".
N = not acceptable for use under normal service conditions (see 3.3)
u = The compatibility depends on the conditions of use (e.g. oxygen). The material may be used where it has
been assessed and authorised by a competent person who specifies the conditions of use.
Abbreviation Material
PTFE Polytetrafluoroethylene
PCTFE Polychlorotrifluoroethylene
PVDF Polyvinylidenefluoride
PA Polyamide
PI Polyimide
PP Polypropylene
POM Polyoxymethylene
PEEK Polyetheretherketone
PPS Polypropylene sulphide
PVC Polyvinyl chloride
IIR Butyl rubber
NBR Nitrile rubber
CR Chloroprene rubber
FKM Fluorocarbon rubber
VMQ Methyl-vinyl-silicone rubber
EPDM Ethylene propylene diene monomer
FVMQ Methyl-fluoro-silicone rubber
ACM Polyacrylate rubber
PUR Polyurethane rubber
HC Hydrocarbon
FC Fluorocarbon
Symbols Risk
7.2.4 Examples
EXAMPLE 1
AP
This example shows an acceptable material/gas combination, suitable for use in normal service conditions,
provided the risk of permeation has been evaluated and found negligible.
EXAMPLE 2
NF,C
1st risk = F
2nd risk = C
This example shows a material/gas combination, not acceptable for general use with non-compatibility risks of
violent reaction (1st risk) and contamination of material (2nd risk).
10
Fluid
Plastics Elastomers MoS2
lubricant
N°
Name Formula R # PTFE PI PCTFE PVDF PA PP POM PEEK PPS PVC IIR NBR CR FKM VMQ EPDM FVMQ ACM PUR HC FC
(UN-No)
98 (2035) 1,1,1-TRIFLUOROETHANE C2H3F3 R143a A - AS A a NS A A A NS NS NS NS A NS NS NS NS NS NW NW A
39 (1030) 1,1-DIFLUOROETHANE C2H4F2 R152a A A AS A A NS NS NS NS NS AS A A NS NS A NS A NS NW NW A
40 (1959) 1,1-DIFLUOROETHYLENE C2H2F2 R1132a A - AS A A NS NS NS A NS NS A A NS NS NS NS NS NS NW NW A
2-TRICHLORO-1,2,2-
97 (3082) C2Cl3F3 R 113 A - AS A AW A AS A A NW NS AS AS AS NS NS NS NS NS NW NW A
TRIFLUOROETHANE
ISO 11114-2:2013(E)
1,2-DICHLORO-1,1,2,2-
36 (1958) C2Cl2F4 R114 A A AS A A NS NS NS A NS AS A A AS NS A NS A A NW NW A
TETRAFLUOROETHANE
BS EN ISO 11114-2:2013
1-CHLORO-1,1-
38 (2517) DIFLUOROCHLORO- C2H3ClF2 R142b A A AS A A NS NS NS NS NS AS AS AS NS NS A NS A NS NW NW A
ETHANE
1-CHLORO-1,2,2,2-
24 (1021) C2HClF4 R124 A - A A A NS NS NS NS NS NS NS NS A NS NS NS NS NS NW NW A
TETRAFLUOROETHANE
1-CHLORO-1,2-
113 (3161) C2H3ClF2 A - A A A NS NS NS NS NS NS NS NS A NS NS NS NS NS A
DIFLUOROETHANE
1-CHLORO-2,2,2-
25 (1983) C2H2ClF3 R133a A A AS A A NS NS NS NS NS a a a A NS a NS NS NS NW NW A
TRIFLUOROETHANE
117 (2044) 2,2-DIMETHYLPROPANE C5H12 A - A A A NS A A A A NS A A A NS NS A NS A
1 (1001) ACETYLENE 2) C2H2 A - A A A W,I A A A A A A NW,I NW,I NW,I NW,I A A NW,I NW,I NW,I NW,I A
105 (1002) AIR 3) AF AF AF AF AF AF AF AF AF AF AF AF AF AF AF AF AF AF AF AF AF A
2 (1005) AMMONIA NH3 A NW A NG,W A A A A A A A NW A NW NW A NW NW NW NW A A
3 (1006) ARGON Ar A A A A A A A A A A A A A A A A A A A A A A
4 (2188) ARSINE AsH3 A A A A A A A A A A A A A A A A A A NW NC,d NC,d A
5 (1741) BORON TRICHLORIDE BCl3 A - A A NW A NW A A A NW NW NW A NW NW A NW NW NW A A
6 (1008) BORON TRIFLUORIDE BF3 A - A A NW A A A A A NR NW NW A NW NW A NW NW NW A A
BROMOTRIFLUORO-
9 (2419) C2BrF3 R123B1 A - AS A NS NS NS NS NS NS NS NS NS A NS NS NS NS NS AW AW A
ETHYLENE
BROMOTRIFLUORO-
8 (1009) CBrF3 R13B1 A A AS A A AS,W A NS NS NS AS AS AS NS NR AS NS A A AW AW A
METHANE
10 (1010) BUTADIENES C4H6 A A A A A A A A A A NS,M NS,M NS,M A NS,M NS,M A NS,M NS,M NW A A
12 (1011) BUTANE C4H10 A A A A A A A A A A NS A A A NS,M NS,M A A A NW A A
13 (1012) BUTYLENE C4H8 A A A A A A A A A NS,M NS,M A NS A NS,M NS,M A NS,M NS,M NW A A
16 (1013) CARBON DIOXIDE CO2 A A A A A A NS,W A A A NS NS,W NS,W NS,W AP AS,W1) A A A A A A
17 (1016) CARBON MONOXIDE CO A A A A A A A A A A AG A A NS A A A A A A A A
109 (2417) CARBONYL FLUORIDE COF2 A NW A NW NW NW NW NW NW NW A A NW A NW A A NW NW NC,d NC,d A
19 (2204) CARBONYL SULPHIDE COS A NW A A A NW NW NW NW A NW NW NW A A NW A NW NW NC NC A
see 6.2.1.2 Warning : There is a risk of violent reactions N
20 (1017) CHLORINE Cl2
A NF A A NF NF NF NF NS NF NF NF NF A NW NF NF NF NF NF A A
110 (1589) CHLORINE CYANIDE ClCN A - A A A A A A A A
CHLORINE
111 (2548) ClF5 A NW A A NW A NW NW NW NW NW NW NW NW NW NW NW NW NW A
PENTAFLUORIDE
112 (1749) CHLORINE TRIFLUORIDE ClF3 A NW A NW NW A NW NW NW NW NW NW NW NW NW NW NW NW NW A
11
Table 1 (continued)
12
Fluid
Plastics Elastomers MoS2
lubricant
N°
Name Formula R # PTFE PI PCTFE PVDF PA PP POM PEEK PPS PVC IIR NBR CR FKM VMQ EPDM FVMQ ACM PUR HC FC
(UN-No)
60 (1051) HYDROGEN CYANIDE HCN A - A A NW A NW NW NW A NW NW NW A NW A NW NW NW NC NC A
61 (1052) HYDROGEN FLUORIDE HF A - A A NW A NW NW NW A NW NW NW A NW A NW NW NW NC NC A
62 (2197) HYDROGEN IODIDE HI A - A A NW A NW NW NW A NW NW NW A NW A NW NW NW NC NC A
124 (2202) HYDROGEN SELENIDE H2Se A A A A A A A A A - - NW - A - - - - - - - A
63 (1053) HYDROGEN SULPHIDE H2S AP A A A A A NW A A A AW NW NW NW NW A NW NW NW NC NC A
ISO 11114-2:2013(E)
13
BS EN ISO 11114-2:2013
ISO 11114-2:2013(E)
BS EN ISO 11114-2:2013
ISO 11114-2:2013(E)
Bibliography
[2] ISO 11114-1, Gas cylinders — Compatibility of cylinder and valve materials with gas contents —
Part 1: Metallic materials
[3] ISO 10156, Gases and gas mixtures — Determination of fire potential and oxidizing ability for the
selection of cylinder valve outlets
[4] ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
[5] ISO 9539, Gas welding equipment — Materials for equipment used in gas welding, cutting and allied
processes
About us Revisions
We bring together business, industry, government, consumers, innovators Our British Standards and other publications are updated by amendment or revision.
and others to shape their combined experience and expertise into standards We continually improve the quality of our products and services to benefit your
-based solutions. business. If you find an inaccuracy or ambiguity within a British Standard or other
The knowledge embodied in our standards has been carefully assembled in BSI publication please inform the Knowledge Centre.
a dependable format and refined through our open consultation process.
Organizations of all sizes and across all sectors choose standards to help Copyright
them achieve their goals. All the data, software and documentation set out in all British Standards and
other BSI publications are the property of and copyrighted by BSI, or some person
Information on standards or entity that owns copyright in the information used (such as the international
We can provide you with the knowledge that your organization needs standardization bodies) and has formally licensed such information to BSI for
to succeed. Find out more about British Standards by visiting our website at commercial publication and use. Except as permitted under the Copyright, Designs
bsigroup.com/standards or contacting our Customer Services team or and Patents Act 1988 no extract may be reproduced, stored in a retrieval system
Knowledge Centre. or transmitted in any form or by any means – electronic, photocopying, recording
or otherwise – without prior written permission from BSI. Details and advice can
Buying standards be obtained from the Copyright & Licensing Department.
You can buy and download PDF versions of BSI publications, including British
and adopted European and international standards, through our website at Useful Contacts:
bsigroup.com/shop, where hard copies can also be purchased. Customer Services
If you need international and foreign standards from other Standards Development Tel: +44 845 086 9001
Organizations, hard copies can be ordered from our Customer Services team. Email (orders): [email protected]
Email (enquiries): [email protected]
Subscriptions
Subscriptions
Our range of subscription services are designed to make using standards
Tel: +44 845 086 9001
easier for you. For further information on our subscription products go to
Email: [email protected]
bsigroup.com/subscriptions.
With British Standards Online (BSOL) you’ll have instant access to over 55,000 Knowledge Centre
British and adopted European and international standards from your desktop. Tel: +44 20 8996 7004
It’s available 24/7 and is refreshed daily so you’ll always be up to date. Email: [email protected]
You can keep in touch with standards developments and receive substantial
Copyright & Licensing
discounts on the purchase price of standards, both in single copy and subscription
format, by becoming a BSI Subscribing Member. Tel: +44 20 8996 7070
Email: [email protected]
PLUS is an updating service exclusive to BSI Subscribing Members. You will
automatically receive the latest hard copy of your standards when they’re
revised or replaced.
To find out more about becoming a BSI Subscribing Member and the benefits
of membership, please visit bsigroup.com/shop.
With a Multi-User Network Licence (MUNL) you are able to host standards
publications on your intranet. Licences can cover as few or as many users as you
wish. With updates supplied as soon as they’re available, you can be sure your
documentation is current. For further information, email [email protected].