Outokumpu Products

Wallchart
Steels with PRE up to 17, Outokumpu
Moda Classic
for mildly corrosive environments. family

Steel designations Performance Typical chemical composition, % by mass

ASTM A 1) Rp0.2 Grade
Outokumpu name EN Type UNS PRE % MPa family C Cr Ni Mo N Others
Moda 430/4016 1.4016 430 S43000 16 20 280 F 0.05 16.2 – – – –
Alternatives
Moda 4510 1.4510 – – 16 23 240 F 0.02 16.2 – – – Ti
Moda 439/4510 1.4510 439 S43035 17 23 240 F 0.02 17.1 – – – Ti
Moda 430Ti/4520 1.4520 430Ti – 16 24 200 F 0.02 16.2 – – – Ti
Moda 4589 1.4589 – S42035 15 16 420 F 0.05 14 1.7 0.3 – Ti
Low-Cr alternatives
Moda 410L/4003 1.4003 410L S40977 12 20 320 F 0.02 11.5 0.5 – – –
Moda 409/4512 1.4512 409 S40910 2) 12 25 220 F 0.02 11.5 0.2 – – Ti
Moda 410S/4000 1.4000 410S S41008 13 19 250 F 0.03 12.5 – – – –
Grade family: F = ferritic. 1) Elongation reference varies between different standards, information referenced here denotes A80 – otherwise see footnote for specific grade or inquire to
reference alternative standard. 2) UNS S40920 is also possible.

Steels with PRE 17–22, Outokumpu

Core Classic
for corrosive environments. family

Steel designations Performance Typical chemical composition, % by mass

ASTM A 1) Rp0.2 Grade
Outokumpu name EN Type UNS PRE % MPa family C Cr Ni Mo N Others
Core 304/4301 1.4301 304 S30400 18 45 230 A 0.04 18.1 8.1 – – –
Core 304L/4307 1.4307 304L S30403 18 45 220 A 0.02 18.1 8.1 – – –
Alternatives
Core 304LN/4311 1.4311 304LN S30453 21 40 290 A 0.02 18.5 9.2 – 0.14 –
Core 304L/4306 1.4306 304L S30403 18 45 220 A 0.02 18.2 10.1 – – –
Core 305/4303 1.4303 305 S30500 18 45 220 A 0.04 17.7 12.5 – – –
Core 321/4541 1.4541 321 S32100 17 40 220 A 0.04 17.3 9.1 – – Ti
Core 347/4550 1.4550 347 S34700 18 40 220 A 0.05 17.5 9.5 – – Nb
Core 301LN/4318 1.4318 301LN S30153 20 35 350 A 0.02 17.7 6.5 – 0.14 –
Core 301/4310 1.4310 301 S30100 17 40 250 A 0.1 17 7 – – –
Low-Ni alternatives
Core 201/4372 1.4372 201 S20100 17 45 350 A 0.05 16.1 3.6 – 0.08 Cu 6.6Mn
Core 201LN/4372 1.4372 201LN S20153 19 45 350 A 0.02 16.2 4.1 – 0.16 Cu 6.6Mn
Ni-free alternatives
Core 441/4509 1.4509 – S43940 18 18 250 F 0.02 17.6 – – – Ti Nb
Core 439M – – S43932 18 22 1) 205 1) F 0.02 17.6 – – – Ti Nb
Core 4622 1.4622 – S44330 21 22 2) 300 2) F 0.02 21 – – – Ti Nb Cu
Grade family: A = austenitic, F = ferritic. 1) Min. values acc. to ASTM A240, for strip t ≤ 5 mm. Elongation reference varies between different standards, information referenced here denotes
A80 – otherwise see footnote for specific grade or inquire to reference alternative standard. 2) Min. values acc. to EN 10028-7.

Steels with PRE 22–26, Outokumpu

Supra Classic
for highly corrosive environments. family

Steel designations Performance Typical chemical composition, % by mass

ASTM A 1) Rp0.2 Grade
Outokumpu name EN Type UNS PRE % MPa family C Cr Ni Mo N Others
Supra 316/4401 1.4401 316 S31600 24 40 240 A 0.04 17.2 10.1 2.1 – –
Supra 316L/4404 1.4404 316L S31603 24 40 240 A 0.02 17.2 10.1 2.1 – –
Alternatives
Supra 316plus 1.4420 – S31655 26 35 2) 350 2) A 0.02 20.3 8.6 0.7 0.19 –
Supra 316/4436 1.4436 316 S31600 25 40 240 A 0.04 16.9 10.7 2.6 – –
Supra 316L/4432 1.4432 316L S31603 25 40 240 A 0.02 16.9 10.7 2.6 – –
Supra 316L/4435 1.4435 316L S31603 26 40 240 A 0.02 17.3 12.6 2.6 – –
Supra 316Ti/4571 1.4571 316Ti S31635 24 40 240 A 0.04 16.8 10.9 2.1 – Ti
Ni-free alternatives
Supra 444/4521 1.4521 444 S44400 25 20 320 F 0.02 18 – 2 – Nb Ti
Grade family: A = austenitic, F = ferritic. 1) Elongation reference varies between different standards, information referenced here denotes A80 – otherwise see footnote for specific grade or
inquire to reference alternative standard. 2) Min. values acc. to EN 10028-7.

PRE = %Cr + 3.3 x %Mo + 16 x %N. Values for Rp0.2 yield strength and the A80 for
elongation are according to EN 10088-2 min. values for cold rolled strip. Chemical
compositions and PRE calculations are based on Outokumpu typical values.
 Duplex and other high strength steels Outokumpu
Forta Pro
(proof strength Rp0.2 > 400 MPa), PRE 16 to 43. family

Steel designations Performance Typical chemical composition, % by mass

ASTM A 1) Rp0.2 Grade
Outokumpu name EN Type UNS PRE % MPa family C Cr Ni Mo N Others
Duplex, high strength, high corrosion resistance and enhanced resistance to stress corrosion cracking
Forta DX 2205 1.4462 – S32205 2) 35 20 500 D 0.02 22.4 5.7 3.1 0.17 –
Forta LDX 2101 1.4162 – S32101 26 20 530 D 0.03 21.5 1.5 0.3 0.22 5Mn Cu
Forta DX 2304 1.4362 – S32304 26 20 450 D 0.02 23 4.8 0.3 0.1 Cu
Forta EDX 2304 1.4362 – S32304 28 25 3) 500 3) D 0.02 23.8 4.3 0.5 0.18 Cu
Forta LDX 2404 1.4662 – S82441 34 20 550 D 0.02 24 3.6 1.6 0.27 3Mn Cu
Forta SDX 100 1.4501 – S32760 42 25 4) 530 4) D 0.02 25.4 6.9 3.8 0.27 W Cu
Forta SDX 2507 1.4410 – S32750 43 20 550 D 0.02 25 7 4 0.27 –
High strength and high ductility
Forta H400 1.4376 – – – 40 400 A 0.04 17.5 4 – 0.2 6.8Mn
Forta H500 – – – – 40 5) 500 5) A 0.32 14 – – 0.32 16Mn
High strength and high hardness (temper rolled) 6)
Forta H800 – – – – 30 7) 800 7) A 0.32 14 – – 0.32 16Mn
Forta H1000 – – – – 13 7) 1000 7) A 0.32 14 – – 0.32 16Mn
Forta 430/4016 1.4016 430 S43000 16 – 350 – 700 F 0.05 16.2 – – – –
Forta 301LN/4318 1.4318 301LN S30153 20 – 500 – 900 A 0.02 17.7 6.5 – 0.14 –
Forta 301/4310 1.4310 301 S30100 17 – 500 – 1300 A 0.1 17 7 – – –
Forta 304/4301 1.4301 304 S30400 18 – 350 – 1300 A 0.04 18.1 8.1 – – –
Forta 304L/4307 1.4307 304L S30403 18 – 350 – 1300 A 0.02 18.1 8.1 – – –
Forta 316/4401 1.4401 316 S31600 24 – 350 – 700 A 0.04 17.2 10.1 2.1 – –
Forta 316L/4404 1.4404 316L S31603 24 – 350 – 700 A 0.02 17.2 10.1 2.1 – –
Forta 316plus 1.4420 – S31655 25 – 500 – 700 7) A 0.02 20.3 8.6 0.7 0.19 –
Forta 316Ti/4571 1.4571 316Ti S32100 24 – 350 – 700 A 0.04 16.8 10.9 2.1 – Ti
Grade family: D = duplex, A = austenitic, F = ferritic. 1) Min. values acc. to ASTM A240, for strip t ≤ 5 mm. Elongation reference varies between different standards, information referenced
here denotes A80 – otherwise see footnote for specific grade or inquire to reference alternative standard. 2) Also available in S31803. 3) Outokumpu MDS-D35 for EDX 2304. 4) Min. values
for plate acc. to EN 10088-2. 5) Values acc. to Stahl-Eisen-Liste. 6) Products with higher strength available on request. 7) Outokumpu tested values.

Steels with PRE > 27, Outokumpu

Ultra Pro
for extremely corrosive environments. family

Steel designations Performance Typical chemical composition, % by mass

ASTM A 1) Rp0.2 Grade
Outokumpu name EN Type UNS PRE % MPa family C Cr Ni Mo N Others
Ultra 904L 1.4539 904L N08904 34 35 240 A 0.01 19.8 24.2 4.3 – 1.4Cu
Ultra 254 SMO 1.4547 – S31254 43 35 320 A 0.01 20 18 6.1 0.2 Cu
Alternatives
Ultra 317L 2) (1.4438) 3) 317L S31703 28 40 4) 205 4) A 0.02 18.2 11.6 3.1 – –
Ultra 725LN 1.4466 – S31050 34 40 5) 250 5) A 0.01 25 22.3 2.1 0.12 –
Ultra 6XN 1.4529 – N08926/ 45 40 5) 300 5) A 0.01 20.5 24.8 6.5 0.2 Cu
N08367
Ultra 654 SMO 1.4652 – S32654 56 40 430 A 0.01 24 22 7.3 0.5 3.5Mn Cu
Ultra Alloy 825 2.4858 6) N08825 34 30 7) 241 7) A 0.01 23 39 3.2 – Cu, Ti
Grade family: A = austenitic. 1) Elongation reference varies between different standards, for coil the standard typically uses A80 – otherwise see footnote for specific grade.
2)
Also available with 11.7% Ni which is not consistent with 1.4438. 3) Quarto plate also available as EN 1.4438. Coil only available as ASTM 317L. 4) Min values acc. to ASTM A-240
5)
Min. values for plate acc. to EN 10088-2. 6) Grade designation according to DIN 17750. 7) Min. values hot-rolled and cold-rolled acc. to ASTM B424.

PRE = %Cr + 3.3 x %Mo + 16 x %N. Values for Rp0.2 yield strength and the A80 for
elongation are according to EN 10088-2 min. values for cold rolled strip. Chemical
compositions and PRE calculations are based on Outokumpu typical values.
 Heat treatable steels Outokumpu
Dura Pro
for greater hardness and strength. family

Steel designations Performance Typical chemical composition, % by mass

ASTM Rm 2) Grade
Outokumpu name EN Type UNS HRC 1) MPa family C Cr Ni Mo N Others
Dura 410/4006 1.4006 410 S41000 – 540 M 0.12 12 – – – –
Dura 4024 1.4024 – – – 550 M 0.16 13.2 – – – –
Dura 420/4021 1.4021 420 S42000 44 – 50 3) 580 M 0.2 13 – – – –
Dura 420/4028 1.4028 420 S42000 45 – 51 3) 620 M 0.3 12.5 – – – –
Dura 420/4031 1.4031 420 S42000 47 – 53 3) 640 M 0.38 13.5 – – – –
Dura 420/4034 1.4034 420 S42000 49 – 55 3) 700 M 0.45 13.7 – – – –
Dura 4419 1.4419 – – 46 – 52 3) 660 M 0.38 13.3 – 0.9 – –
Dura 4110 1.4110 – – 50 – 56 3) 680 M 0.5 14.8 – 0.6 – –
Dura 4116 1.4116 – – – 680 M 0.5 14.4 – 0.6 – V
Dura 4122 1.4122 – – 47 – 53 3) 650 M 0.41 16.1 – 1 – –
Precipitation hardening
Dura 17-7PH 1.4568 631 S17700 38 – 41 4) 820 PH 0.08 17 7 – – AI
Dura 17-4PH 1.4542 630 S17400 24 – 40 4) 1100 PH 0.02 15.5 4.8 – – 3.4Cu Nb
Grade family: M = martensitic, PH = precipitation hardening. 1) Achievable Rockwell hardness after final heat treatment of the fabricated part. 2) Tensile strength in mill condition,
Outokumpu typical values. 3) Hardness range according to EN 10088-2. 4) Hardness range according to ASTM A564 (minimum values for different heat treatment conditions).

Outokumpu
Therma Steels for high temperature applications (> 550 °C). Pro
family

Steel designations Performance Typical chemical composition, % by mass

ASTM Max. service Grade
Outokumpu name EN Type UNS temp. (°C) 1) family C Cr Ni Mo N Others
Therma 253 MA 1.4835 – S30815 1150 A 0.09 21 11 – 0.17 Si Ce
Therma 310S/4845 1.4845 310S S31008 1050 A 0.05 25.5 19.1 – – –
Resistance to sulfur containing hot gases, lower thermal expansion
Therma 4713 1.4713 – – 800 F 0.06 6.5 – – – Al Si
Therma 4724 1.4724 – – 850 F 0.07 12.5 – – – Al Si
Resistance to carburizing and nitriding/low oxygen hot gas, higher creep strength
Therma 304H/4948 1.4948 304H S30409 750 A 0.05 18.1 8.3 – – –
Therma 321H/4878 1.4878 321H – 850 A 0.05 17.3 9.1 – – Ti
Therma 347H – 347H S34709 700 A 0.05 17.5 9.5 – – Nb
Therma 4828 1.4828 – – 1000 A 0.05 19.3 11.2 – – Si
Therma 309S/4833 1.4833 309S S30908 1000 A 0.06 22.3 12.3 – – –
Therma 314/4841 1.4841 314 S31400 1150 A 0.06 24.3 19.2 – – Si
Grade family: A = austenitic, F = ferritic. 1) In dry air acc. EN 10095.

Stainless steel grades optimized for improved machinability Outokumpu

Prodec Pro
with longer tool life and enhanced quality. family

Steel designations Performance Typical chemical composition, % by mass

HRB 1) CDB 2)
ASTM A 3) Rp0.2 A 3) Rp0.2 Grade
Outokumpu name EN Type UNS PRE % MPa % MPa family C Cr Ni Mo N Others
Plate
Prodec 304L/4307 4) 1.4307 304L S30403 18 45 7) 200 7) – – A 0.02 18.2 8.1 – – –
Prodec 316L/4404 5) 1.4404 316L S31603 25 45 7) 220 – – A 0.02 17.2 11.1 2.3 – –
Prodec 316L/4432 6) 1.4432 316L S31603 25 45 7) 220 – – A 0.02 16.8 10.7 2.6 – –
Bar
Prodec 304L/4307 1.4307 304L S30403 18 45 175 25/25/30 400/380/175 A 0.02 18.1 8.1 – – 0.03S
Prodec 316L/4404 1.4404 316L S31603 24 40 200 25/25/30 400/380/200 A 0.02 17.2 10.1 2.1 – 0.03S
Prodec 303/4305 1.4305 303 S30300 17 35 190 15/15/20 400/400/190 A 0.05 17.2 8.1 – – 0.3S
Prodec 17-4PH 8) 1.4542 630 S17400 – 10 520 10/10/12 600/600/520 PH 0.02 15.5 4.8 – – 3.4Cu Nb 0.03S
Grade family: A = austenitic, PH = precipitation hardening. 1) HRB = Hot rolled bar. 2) CDB = Cold drawn bar. Values are for diameter (d) ≤ 10 mm & 10 < d ≤ 16 mm & 16 < d ≤ 40 mm.
3)
Elongation reference varies between different standards, for coil the standard typically uses A80 – otherwise see footnote for specific grade. 4) Also available as ASTM 304/EN 4301.
5)
Also available as ASTM 316/EN 4346. 6) Also available as ASTM 316/EN 4401. 7) min values plate acc. To 10088-2. 8) Values for condition +P800.

PRE = %Cr + 3.3 x %Mo + 16 x %N. Values for Rp0.2 yield strength and the A80 for
elongation are according to EN 10088-2 min. values for cold rolled strip. Chemical
compositions and PRE calculations are based on Outokumpu typical values.
 Outokumpu
Deco Special surfaces. Pro
family

EN ASTM Description Available Available Available

Finish steel grades 1) versions dimensions 2)
Polished/brushed
Deco 4N 2K 4 Most-sold polish at Outokumpu with elegant, satin-like look. most of Moda, – 0.5–5.5 mm thick
Deco Microlon 2K 4 Elegant, dark grey surface finish that gives interior and exterior Core and Supra up to 1524 mm wide
claddings a classy look.
Brushed No.5 2J 6 Slightly glossy and elegant finish in between a fine polished and a
fine brushed look.
Patterned
Deco Square 2M – Clearly structured pattern creating a technical impression. Raised Moda 430/4016 (standard) 0.3–3.5 mm thick
and recessed sections have different reflection characteristics. Core 441/4509 Star up to 1500 mm wide
Deco Croc Skin 2M – Combines the advantages of a stainless steel surface with Core 304/4301 Matt
an organic-like texture. Core 304L/4307 Supermatt
Deco Diamonds 2M – Strictly geometric pattern given added tension by its diagonal Supra 316/4401
orientation. Supra 316L/4404
Deco Linen 2M – Pattern of closely alternating dots and dashes resembling a textile Forta DX 2205
surface, remains intact even under forming.
Deco Linen without Slubs 2M – Removing the distinctive linen thread makes Deco Linen less
directional and increases its even and elegant look.
Deco Vertical Linen 2M – The slubs of regular Deco Linen are tilted by 90° to create
a smoother pattern flow and enhanced verticality.
Deco Nine 2M – A coarser version of Deco Linen with more pronounced linen
threads.
Deco Microlinen 2M – A scaled-down version of the typical Deco Linen pattern causing
a finer, denser and more delicate appearance.
Deco Microlinen without Slubs 2M – The scaled-down version of Deco Linen is available without the linen
thread to create a fine, dense and less directional finish.
Deco Bark 2M – Creates an organic allurement by picking up the vertical groove-like
structure of wood.
Deco Rill 2M – The highly precise alternation between high and low running rills
generates a strict linearity.
Deco Haze 2M – Finish appears like sun shine through fog. Capable of withstanding
heavy forming operations.
Deco Bricks 2M – Scaled-down version of a brick wall, creating an industrial
impression.
Deco Austenite 2M – Modeled on the microstructure of an austenitic stainless steel,
plays with the light to create a dazzling effect.
Deco Laser 2M – Digitalized micro-patterns, randomly arranged without pattern
repetition. A nearly homogenenous surface is observed under all
viewing angles and light conditions.
Deco Ice Crystals 2M – Irregular coarse structure. Insensitive to fingerprints, scratches and
other surface damages.
Deco Leather Grain 2M – Irregular structure similar to a leather surface. Insensitive to
fingerprints, scratches and other surface damages.
Deco Sand Surface 2M – Fine irregulare structure creating the impression of a sand surface.
Special surfaces
Deco 2R² 2R BA High-gloss surface closing the gap between standard bright an- Core 304/4301, – 0.4–1.2 mm thick
nealed and mirror polished materials. Core 304L/4307 up to 1500 mm wide
Supra 316/4401,
Supra 316L/4404
Deco Supermatt 2E – Industrially shot blasted surface finish with a homogeneously matt Core 304/4301, (standard) 0.5–4.5 mm thick
high class appearance. Core 304L/4307 Deco Supermatt 1800d up to 1500 mm wide
Supra 316/4401, Deco Supermatt 2400d
Supra 316L/4404
Deco Rolled-On 2F 3/4 A rolled-on finish with similar properties and appearance to a pol- Moda 430/4016 – 0.4–3.4 mm thick
ished surface but with easy-to-clean properties and good corrosion Core 304/4301, up to 1219 mm wide
resistance. Core 304L/4307
1)
Other grades on request. 2) Full details on request.

Outokumpu product ranges

outokumpu
classic

outokumpu
pro

PRE = %Cr + 3.3 x %Mo + 16 x %N. Values for Rp0.2 yield strength and the A80 for
elongation are according to EN 10088-2 min. values for cold rolled strip. Chemical
compositions and PRE calculations are based on Outokumpu typical values.

MODA, CORE, SUPRA, FORTA, ULTRA, DURA, THERMA, DECO and

316plus are trademarks of Outokumpu Oyj.

PRODEC, EDX, FDX, FDX 27, LDX, 253 MA, 254 SMO, 654 SMO, LDX 2101, LDX
2404 are registered trademarks of Outokumpu Oyj.

17-4-PH and 17-7 PH are registered trademarks AK Steel Corporation.

 Performance
Strength vs. corrosion resistance
600

1000EN-US:16. February, 2021.

Yield strength Rp0.2 (MPa)

550 Forta LDX 2404 Forta SDX 2507

Forta LDX 2101 Forta SDX 100 4)

500 Forta
Forta DX 2205
EDX 2304 3)

450 Forta DX 2304

Ultra 654 SMO
Moda 4589
400
Core 201LN/4372
Core
350 Core 201/4372
301LN/4318
Supra 316plus 2)

Moda 410L/4003 Supra 444/4521 Ultra 254 SMO

300 Core 4622 2) Ultra 6XN 4)
Core 304LN/4311 Supra 316L/4432
Moda 430/4016 Supra 316/4436
Core 301/4310
Ultra Alloy 825 6)
250 Moda 410S/4000 Core 441/4509
Ultra 725LN 4)
Core Supra 316L/4435
304/4301 Ultra 904L
Moda 409/4512
200 Ultra 317L 5)

Moda 4510 Core 304L/4307

Core
Moda Core 304L/4306 Supra 316/4401
Moda 439/4510 439M 1)
430Ti/ Core 305/4303 Supra 316L/4404
0 Core 321/4541 4520 Core 347/4550 Supra 316Ti/4571

0 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60
Corrosion resistance (PRE)

Elongation vs. corrosion resistance

55
Elongation (%)

Core 304/4301 Supra 316/4401

Core 304L/4307 Supra 316L/4404
50 Core 304L/4306 Supra 316Ti/4571
Core 305/4303
Supra 316/4436
Supra 316L/4432
45 Core 201/4372 Core 201LN/4372
Supra 316L/4435
Core 321/4541 Core 304LN/4311
Core 301/4310
40 Ultra 317L 5)
Ultra 725LN 4)
Ultra 6XN 4)
Ultra 654 SMO
Core 347/4550

35 Core 301LN/4318
Supra
Ultra 904L Ultra 254 SMO
316plus 2)

Moda 430Ti/4520
30 Ultra Alloy 825 6)

Moda 439/4510

Core 439M 1)
25 Moda 409/4512 Forta EDX 2304 3)
Forta SDX 100 4)

Moda 4510
Core 4622 2)

20 Moda 410L/4003 Moda 430/4016

Supra
Forta LDX 2404 Forta DX 2205 Forta SDX 2507

Moda 410S/4000 444/4521

Core Forta LDX 2101
15 441/4509 Forta DX 2304
Moda 4589

0
0 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60

Corrosion resistance (PRE)

Moda
Moda –– Mildly
Steelscorrosive
for mildlyenvironments
corrosive environments (PRE ≤17) Values for Rp0.2 yield strength and the A80 for elongation are according to EN 10088-2 min. values for
cold rolled strip. Chemical compositions and PRE calculations are based on Outokumpu typical values.
Core Steels forenvironments
Core – Corrosive corrosive environments (PRE 17–22)
Supra –– Highly
Supra Steelscorrosive
for highlyenvironments
corrosive environments (PRE 22–26)
1)
Elongation reference varies between different standards, for coil the standard typically uses A80 –
otherwise see footnote for specific grade.
Forta Duplex and
Forta – Duplex steels (PRE
other high26–43)
strength (PRE 16 to 43) 2)
Min. values acc. to EN 10028-7.
Ultra Steels for corrosive
Ultra – Extremely extremelyenvironments
corrosive environments
(PRE > 27) (PRE > 27) 3)
Outokumpu MDS-D35 for EDX 2304.
4)
Min. values for plate acc. to EN 10088-2.
5)
Min values acc. to ASTM A-240.
6)
Min. values hot-rolled and cold-rolled acc. to ASTM B424.

Please see values for other product forms at steelfinder.outokumpu.com