INCH-POUND

MS20756G
28 March 2018
SUPERSEDING
MS20756F
w/AMENDMENT 2
6 March 2014

DETAIL SPECIFICATION SHEET

FLANGE, SWIVEL, RETAINING

This specification is approved for use by all Departments and

Agencies of the Department of Defense.

The requirements for acquiring the product described herein shall consist of this specification sheet and
SAE-AS4875.

Inches mm
.005 0.13
.010 0.25
.062 1.57

FIGURE 1. Swivel fitting flange type I rectangle size 8 through 32.

AMSC N/A FSC 4730

 MS20756G

A
+.015 C dia D dia
Tubing B
-.005 (see note 4) (see note 4) E
Size OD and +.005/-.000
(+0.38 +.010/-.000 +.005/-.000 (see note 9)
designator hose ID (+0.13/-0.00)
-0.13) (+0.25/-0.00) (+0.13/-0.00) inches (mm)
inches (mm) inches (mm)
inches inches (mm) inches (mm)
(mm)
1.390
8 .500 (12.70) .750 (19.05) .885 (22.48)
(35.31)
1.468
10 .625 (15.88) .880 (22.35) 1.010 (25.65)
(37.29) ±.016
.234 1.260 1.594 (0.41)
12 .750 (19.05) .136 (3.45) 1.125 (28.58)
(5.94) (32.00) (40.49)
1.510 1.750
16 1.000 (25.40) 1.375 (34.93)
(38.35) (44.45)
1.854 2.188
20 1.250 (31.75) 1.688 (42.88)
(47.09) (55.58)
2.135 2.375 ±.020
24 1.500 (38.10) 1.938 (49.23)
.297 (54.23) (60.33) (0.51)
.168 (4.27)
(7.54) 2.760 3.000
32 2.000 (50.80) 2.562 (65.07)
(70.10) (76.20)

H dia
G +.010/- J radius K dia M
±.005 .000 (see note 9) (see note 9) L dia ±.016
Size
(±0.13) (+0.25 ±.016 ±.015 ±.005 (0.25mm) (±0.41) N
number
inches -0.00) (±0.41) (±0.38) inches (mm) inches
(mm) inches inches (mm) inches (mm) (mm)
(mm)
.950
8 1.782 (45.26) 1.344 (34.14)
(24.13)

1.038 20°
10 .205 1.906 (48.41) 1.468 (37.29)
(26.37) .219 (5.56)
(5.21) .296
1.156 (7.52)
12 2.094 (53.19) 1.635 (41.53)
(29.36)
1.312
16 2.312 (58.72) 1.855 (47.12) 18°
(33.32)
1.656
20 .266 (6.76) 2.875 (73.03) 2.342 (59.49)
(42.06) .266
16°
1.812 (6.76)
24 .281 (7.14) 3.094 (78.59) 2.562 (65.07)
(46.02) .359
2.375 .328 (9.12)
32 .312 (7.92) 3.953 (100.41) 3.359 (85.32) 12°
(60.33) (8.33)

FIGURE 1. Swivel fitting flange type I rectangle size 8 through 32 - Continued.

2
 MS20756G

Weight max (estimated)

Size
lbs (gram)
number
Steel Al alloy Titanium
8 .03 (14) .01 (5) .02 (9)
10 .05 (23) .02 (9) .03 (14)
12
.08 (36) .03 (14) .04 (18)
16
20 .14 (64) .05 (23) .07 (32)
24 .17 (77) .06 (27) .09 (41)
32 .25 (113) .09 (41) .13 (59)

NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances linear dimensions ±.005 inch (0.13 mm) angles ±.5°.
4. Diameters C and D shall be concentric within .010 inch (0.25 mm) full indicator movement.
5. Unless otherwise specified, the surface roughness shall not exceed 100 microinches (25.4 µm) Ra in
accordance with ASME B46.1.
6. Break all sharp edges; remove all loose or hanging burrs and slivers that may become dislodged.
7. For tube sizes -8 through -16, maximum operating temperature 275°F (135°C), maximum pressure 1500
psi (10 MPa).
8. For tube sizes -20 though -32, maximum operating temperature 275°F (135°C), maximum pressure 500
psi (3.4 MPa).
9. Reduction by forging draft angle of 7° maximum is permissible if forged.

FIGURE 1. Swivel fitting flange type I rectangle size 8 through 32 - Continued.

3
 MS20756G

Inches mm
.005 0.13
.010 0.25

A
+.015 C dia D dia
Tubing B
-.005 (see note 4) (see note 4) E
Size OD and +.005/-.000
(+0.38 +.010/-.000 +.005/-.000 (see note 9)
designator hose ID (+0.13/-0.00)
-0.13) (+0.25/-0.00) (+0.13/-0.00) inches (mm)
inches (mm) inches (mm)
inches inches (mm) inches (mm)
(mm)
.885 1.538
8 .500 (12.70) .750 (19.05)
(22.48) (39.07)
1.010 1.644
10 .625 (15.88) .880 (22.35)
(25.65) (41.76) ±.016
.234 1.260 1.813 (0.41)
12 .750 (19.05) .136 (3.45) 1.125 (28.58)
(5.94) (32.00) (46.05)
1.510 2.000
16 1.000 (25.40) 1.375 (34.93)
(38.35) (50.80)
1.854 2.460
20 1.250 (31.75) 1.688 (42.88)
(47.09) (62.48)
2.135 2.680
24 1.500 (38.10) 1.938 (49.23)
(54.23) (68.07)
2.760 3.359 ±.020
32 2.000 (50.80) 2.562 (65.07)
.297 (70.10) (85.32) (0.51)
.168 (4.27)
(7.54) 3.291 4.000
40 2.500 (63.50) 3.062 (77.77)
(83.59) (101.60)
3.791 4.500
48 3.000 (76.20) 3.562 (90.47)
(96.29) (114.30)

FIGURE 2. Swivel fitting flange type II hexagon size 8 through 48.

4
 MS20756G

J radius K dia
H dia
(see note 9) (see note 9) L dia
Size +.010/-.000
±.016 ±.015 ±.005 (0.25mm)
number (+0.25/-0.00)
(±0.41) (±0.38) inches (mm)
inches (mm)
inches (mm) inches (mm)

8 1.782 (45.26) 1.344 (34.14)

.205
.219 (5.56)
10 (5.21) 1.906 (48.41) 1.468 (37.29)

12 2.094 (53.19) 1.635 (41.53)

16 2.312 (58.72) 1.855 (47.12)
20 .266 .266 (6.76) 2.875 (73.03) 2.342 (59.49)
24 (6.76) .281 (7.14) 3.094 (78.59) 2.562 (65.07)
32 .312 (7.92) 3.953 (100.41) 3.359 (85.32)
.328
40 .375 (9.53) 4.500 (114.30) 3.812 (96.82)
(8.33)
48 .625 (15.88) 5.000 (127.00) 4.312 (109.52)

Weight max (estimated)

Size
lbs (gram)
number
Steel Al alloy Titanium
8 .03 (14) .01 (5) .02 (9)
10 .05 (23) .02 (9) .03 (14)
12
.08 (36) .03 (14) .04 (18)
16
20 .14 (64) .05 (23) .07 (32)
24 .17 (77) .06 (27) .09 (41)
32 .25 (113) .09 (41) .13 (59)
40 .45 (204) .16 (73) .21 (95)
48 .53 (240) .19 (86) .24 (109)

NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances linear dimensions ±.005 inch (0.13 mm) angles ±.5°.
4. Diameters C and D shall be concentric within .010 inch (0.25 mm) full indicator movement.
5. Unless otherwise specified, the surface roughness shall not exceed 100 microinches (25.4 µm) Ra in
accordance with ASME B46.1.
6. Break all sharp edges; remove all loose or hanging burrs and slivers that may become dislodged.
7. For tube sizes -8 through -16, maximum operating temperature 275°F (135°C), maximum pressure 1500
psi (10 MPa).
8. For tube sizes -20 though -48, maximum operating temperature 275°F (135°C), maximum pressure 500
psi (3.4 MPa).
9. Reduction by forging draft angle of 7° maximum is permissible if forged.

FIGURE 2. Swivel fitting flange type II hexagon size 8 through 48 - Continued.

5
 MS20756G

Inches mm
.005 0.13
.010 0.25

A B
H dia
+.015/ +.005/
Tubing C dia +.010/
-.005 -.000 D dia
Size OD and (see note 4) -.000
(+0.38/ (+0.13/ (see note 4)
number hose ID ±.031 (0.79) (+0.25/
-(0.13) -.000) inches (mm)
inches (mm) inches (mm) -0.00)
inches inches
inches (mm)
(mm) (mm)
4.234
56 3.500 (88.90) 3.968 (100.79)
.312 .168 (107.54) +.010/
(7.92) (4.27) 4.797 -.000
64 4.000 (101.60) 4.531 (115.09)
(121.84) (+0.25/
5.797 -0.000) .328
80 5.000 (127.00) 5.531 (140.49)
.375 .188 (147.24) (8.33)
(9.53) (4.78) 6.797 +.020/
96 6.000 (152.40) 6.531 (165.89)
(172.64) -.000
.437 .200 7.860 (0.51/
112 7.000 (177.80) 7.594 (192.89)
(11.10) (5.08) (199.64) -.000)

FIGURE 3. Swivel fitting flange type III round size 56 through 112.

6
 MS20756G

K dia
(see note 8) L dia P
Size
±.015 Ref number of
number
(±0.38) inches (mm) holes
inches (mm)
56 5.562 (141.27) 4.875 (123.83)
8
64 6.125 (155.58) 5.438 (138.13)
80 7.125 (180.98) 6.438 (163.53) 10
96 8.125 (206.38) 7.438 (188.93) 12
112 9.188 (233.38) 8.500 (215.90) 14

NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances linear dimensions ±.005 inch (0.13 mm) angles ±.5°.
4. Diameters C and D shall be concentric within .010 inch (0.25 mm) full indicator movement.
5. Unless otherwise specified, the surface roughness shall not exceed 100 microinches (2.54 µm) Ra
in accordance with ASME B46.1.
6. Break all sharp edges; remove all loose or hanging burrs and slivers that may become dislodged.
7. Maximum operating temperature 275°F (135°C), maximum pressure 500 psi (3.4 MPa).
8. Reduction by forging draft angle of 7° maximum is permissible if forged.

FIGURE 3. Swivel fitting flange type III round size 56 through 112 - Continued.

REQUIREMENTS:

Design and construction:

Dimensions and configuration: See figures 1, 2, and 3.

For nominal use on fuel and oil systems.

Materials: Materials shall be in accordance with SAE-AS4875.

Material designators (see table I): Designators for material types shall be in accordance with
SAE-AS4875.

Material and size designators shall be in accordance with table I.

7
 MS20756G

TABLE I. Material and size designators. 1/

Size number with letter material

Size designator
number Steel Aluminum Titanium
CRES
(Blank) alloy 2/
8 -8 -W8 -R8 -T8
10 -10 -W10 -R10 -T10
12 -12 -W12 -R12 -T12
16 -16 -W16 -R16 -T16
20 -20 -W20 -R20 -T20
24 -24 -W24 -R24 -T24
32 -32 -W32 -R32 -T32
40 -40 -W40 -R40 -T40
48 -48 -W48 -R48 -T48
56 -56 -W56 -R56 -T56
64 -64 -W64 -R64 -T64
80 -80 -W80 -R80 -T80
96 -96 -W96 -R96 -T96
112 -112 -W112 -R112 -T112
1/ Materials and designators blank/none, “W”, “R”, and “T” are in accordance
with SAE-AS4875.
2/ Titanium shall not be used in oxygen systems.

Finishes. Finish and finish designators shall be as specified in table II. All plating’s shall be capable
of meeting a minimum of 96 hours salt spray test in accordance with ASTM B117. The fittings shall
show no evidence of red corrosion after 96 hours of salt spray. Fluid passages, other openings and
internal threads shall not be subject to the plating thickness requirement and may have bare areas
provided they are protected with a light film of oil.

8
 MS20756G

TABLE II. Flange finish code.

PIN code
Material Plating finish
dash letter
Cadmium plating in accordance with SAE-AMS-C-81562, type
Steel
II, class 3 or SAE-AMS-QQ-P-416, type II, class 2. 1/
Aluminum 2/ Anodize in accordance with MIL-A-8625, type II.
Blank
No additional finish. Passivation in accordance with
CRES
SAE-AMS2700, type 6 or 7.
Titanium 3/ Fluoride phosphate in accordance with SAE-AMS2486. 4/
Aluminum-nickel in accordance with ASTM F1136/F1136M,
-A Steel
grade 3, NC
Anodize in accordance with MIL-A-8625, type II then apply
-D Aluminum 2/ NAVAIR trivalent chromium pretreatment (TCP) in accordance
with MIL-DTL-81706, type II, class 1A.
Chemical conversion coating in accordance with,
DA Aluminum 2/
MIL-DTL-5541, type II, class 3
Zinc plating with colorless passivate in accordance with
-G Steel
ASTM B633, type V, Fe/Zn 25. 6/
Zinc phosphate finish in accordance MIL-DTL-16232 type Z,
-H Steel
class 1. 6/
Zinc plating in accordance with ASTM B633; type II or III, Fe/Zn
-J Steel
5, or ASTM B695, type II, class 5. 6/
Zinc plating in accordance with ASTM B633; type III or V,
-R Steel
Fe/Zn 8. 6/
-T Titanium 4/ Anodized in accordance with SAE-AMS2488, type 2
-V Steel Zinc-nickel in accordance with SAE-AMS2417, type 1. 5/ 6/
Zinc plating in accordance with ASTM B695, type II, class 8. 3/
-Z Steel
6/
-ZN Steel Zinc may be any zinc plating’s from PIN codes R, V, Z. 6/
1/ Cadmium shall not be used in oxygen or potable water systems. Cadmium is prohibited from use in
NAVSEA owned shipboard systems.
2/ Aluminum alloy 7075 shall be dyed brown.
3/ Titanium shall not be used in oxygen systems.
4/ A pretreatment, a modification of the fluoride treatment, or a post treatment shall be applied so the
final color of the fittings shall be similar to SAE-AMS-STD-595 colors 36076 through 36293. Titanium
shall not be used in oxygen or potable water systems.
5/ The zinc-nickel alloy plate shall contain 12% to 16% nickel. The coating thickness shall be 315µ
inches (8µm) minimum. Hexavalent chromium free. Finish shall be ROHS compliant.
6/ Not for use in Aircraft. Requires approval from the Program Office for all applications. Zinc-plated
materials should be avoided in hydraulic systems with water-glycol fluids. Reference ASTM MNL37 -
Fuels and Lubricants Handbook, "water glycol fluids are highly alkaline due to the presence of amine
based corrosion inhibitors. As a result, these fluids can attack zinc, cadmium, magnesium, and non-
anodized aluminum, forming sticky or gummy residues. Consequently, these metals should be
avoided when selecting system components.

9
 MS20756G

Trivalent wrenchability. Applies to aluminum fittings that receive the NAVAIR TCP coating in
accordance with MIL-DTL-81706, type II. When the finish has been damaged due to poor
wrenchability, the surface of the flange shall be touched up using the brush plating process below.
The term "trivalent wrenchability" is used to evaluate the ability of the finish to withstand abrasion
from an excessive amount of wrenching.

Brush plating of NAVAIR TCP shall be in accordance with MIL-DTL-81706, type 2, class 1A, material
form 1 through 6, application method B. Example of a PIN: M817062A6B.

PIN example:

MS 20756 -W12 -D
“Blank” for type I rectangle and type II hexagon for
sizes 40 and 48 and round.
“2” for type II hexagon for sizes 8 through 32 only.

Material finish code (see table II)

Material and size number (see table I)

Specification number

MS prefix

MS20756-W12-D indicates: Flange, .750 inch (19.05 mm) tube ID, aluminum anodized then NAVAIR
TCP applied, type I rectangle.

MS20756-W12-D2 indicates: Flange, .750 inch (19.05 mm) tube ID, aluminum anodized with
NAVAIR TCP, type II hexagon.

MS20756-56 indicates: Flange, 3.500 inch (88.90 mm) tube ID, steel, cadmium plating in accordance
with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2, type III round.

Marking. The complete PIN shall be permanently marked on an unfinished surface.

Guidance on use of alternative parts with less hazardous or nonhazardous materials. This
specification provides for a number of alternative plating materials via the PIN. Users should select
the PIN with the least hazardous material that meets the form, fit and function requirements of their
application.

Cadmium is prohibited from use in NAVSEA owned shipboard systems in accordance with the
requirements of T9070-AL-DPC-020/077-2.

Class I and II ozone depleting substances (ODS) shall not be used in MS20756 or any referenced
procedures.

Referenced documents shall be of the issue in effect on date of invitations for bid.

This standard takes precedence over documents referenced herein.

10
 MS20756G

Supersession data:

Aluminum alloys 2014 and 2024 "D" designator is cancelled. For new and existing designs, use
aluminum alloy 7075 "W" designator.

CRES alloy 304 "J" designator is cancelled. For new and existing designs, use CRES alloy 321
"R" designator.

For nominal use on fuel and oil systems.

Previous issue. Marginal notations are not used in this revision to identify changes with respect to the
previous issue, due to the extent of the changes.

Referenced documents. In addition to SAE-AS4875, this document references the following:

MIL-A-8625 SAE-AMS-STD-595/36076 SAE-AMS-STD-595/36270

MIL-DTL-5541 SAE-AMS-STD-595/36081 SAE-AMS-STD-595/36280
MIL-DTL-16232 SAE-AMS-STD-595/36099 SAE-AMS-STD-595/36293
MIL-DTL-81706 SAE-AMS-STD-595/36118 SAE-AMS2417
ASME B46.1 SAE-AMS-STD-595/36134 SAE-AMS2486
ASTM B117 SAE-AMS-STD-595/36152 SAE-AMS2488
ASTM B633 SAE-AMS-STD-595/36170 SAE-AMS2700
ASTM B695 SAE-AMS-STD-595/36173 SAE-AMS-QQ-P-416
ASTM F1136/F1136M SAE-AMS-STD-595/36176 T9070-AL-DPC-020/077-2
ASTM MNL37 SAE-AMS-STD-595/36231
SAE-AMS-C-81562 SAE-AMS-STD-595/36251

CONCLUDING MATERIAL

Custodians: Preparing activity:

Army - AT DLA - CC
Navy - AS
Air Force - 99 (Project 4730-2018-042)
DLA - CC

Review activities:
Navy - SA
Air Force - 85

NOTE: The activities listed above were interested in this document as of the date of this document.
Since organizations and responsibilities can change, you should verify the currency of the information
above using the ASSIST Online database at https://assist.dla.mil.

11