Professional Documents
Culture Documents
MetodologiaEHAvsEMA
MetodologiaEHAvsEMA
http://pig.sagepub.com/content/early/2014/11/11/0954410014544303.full.pdf+html
DOI: 10.1177/0954410014544303
Journal name
000(00):1–13
A Methodology for Vehicle and Mission ©The Author(s) 2010
Reprints and permission:
Abstract
As part of the More Electric Initiative, there is a significant interest in designing energy-optimized More Electric Aircraft,
where electric power meets all non-propulsive power requirements. To achieve this goal, the aircraft subsystems must
be analyzed much earlier than in the traditional design process. This means that the designer must be able to compare
competing subsystem solutions with only limited knowledge regarding aircraft geometry and other design characteristics.
The methodology presented in this work allows such tradeoffs to be performed, and is driven by subsystem requirements
definition, component modeling and simulation, identification of critical or constraining flight conditions, and evaluation of
competing architectures at the vehicle and mission level. The methodology is applied to the flight control actuation system,
where electric control surface actuators are likely to replace conventional centralized hydraulics in future More Electric
Aircraft. While the potential benefits of electric actuation are generally accepted, there is considerable debate regarding
the most suitable electric actuator - electrohydrostatic or electromechanical. These two actuator types form the basis of
the competing solutions analyzed in this work, which focuses on a small narrowbody aircraft such as the Boeing 737-800.
The competing architectures are compared at both the vehicle and mission levels, using as metrics subsystem weight and
mission fuel burn respectively. As shown in this work, the use of this methodology aids the decision-making process by
allowing the designer to rapidly evaluate the significance of any performance advantage between the competing solutions.
Keywords
More Electric Aircraft, More Electric Initiative, electric actuator, electrohydrostatic actuator, electromechanical actuator
∗ Senior Graduate Researcher, Aerospace Systems Design Laboratory, School of Aerospace Engineering, Georgia Tech,
Corresponding author; e-mail: [email protected]
† Boeing Chaired Professor, School of Aerospace Engineering, and Director, Aerospace Systems Design Laboratory, Georgia Tech
‡ Senior Business Development Manager, PACE America
§ Founding Member, PACE GmbH, and President, PACE America
1. Introduction - Consideration of More Electric Subsystems in Conceptual Design
The conceptual design phase of the traditional aircraft design process typically gives only limited consideration to the aircraft
subsystems1 , which are addressed mainly in the late-preliminary and detailed design phases (1). This approach has proven
adequate when applied to aircraft with conventional subsystem solutions due to the presence of a continuously-updated
historical database and a relative lack of coupling/interactions between different subsystems.
This will not be the case, however, for conceptual design of More Electric Aircraft (MEA) or, in the limit, All Electric
Aircraft (AEA), for which there is no equivalent historical data, and where subsystem interactions may be significant. As
indicated by Faleiro, MEA/AEA design will necessitate a new design paradigm that considers the aircraft and its subsystems
as a system of systems (2). More thorough consideration must therefore be given to the requirements, interactions, and
effects of the aircraft subsystems even in the conceptual design phase.
This paper presents a requirements-driven methodology aimed at MEA/AEA design that integrates the analysis of
subsystem requirements and effects with the conceptual phase aircraft sizing process (Fig. 1(a)). For each subsystem, the
functional requirements are set by identifying constraining operating scenarios. The subsystem is sized to those requirements
using conceptual phase aircraft parameters from the aircraft sizing analysis (dimensions, estimated takeoff gross weights,
etc.). Fallouts such as subsystem weight (Wsub ), non-propulsive power requirement (Pnp ), and drag coefficient change
(∆CD , if any), can be fed back to the aircraft and propulsion system sizing analyses for the subsequent iteration (if ‘Cycle?=
Yes’). The convergence of this iterative process yields a design where conceptual design parameters such as aircraft weight,
wing area, propulsion requirements, etc. were computed by representing subsystem requirements and effects explicitly.
(a) Methodology linking subsystem sizing with traditional conceptual design phase aircraft sizing, (b) Application to flight control actuation system with
with feed-back information flow to enable design “cycling” in response to subsystem changes electrically actuated flight control surfaces
Fig. 1. Integrating subsystem sizing into the traditional aircraft sizing activity in the conceptual design phase
1 In this work, by “subsystems” the authors mean Aircraft Equipment Systems (AES) such as actuation systems for flight control surfaces, landing gear,
thrust reversers, nosewheel steering, and wheel braking, the environmental control system (ECS) and ice protection systems (IPS), engine starting, etc.
This paper focuses on the application of this methodology to electric flight control actuation systems. As seen in
Fig. 1(b), the steps involved mirror the general steps of Fig. 1(a), and form the subject of subsequent sections of the paper.
Section 2 gives an overview of flight control actuation systems. Section 3 derives the actuation requirements of the control
surfaces, which feed into the actuator models that are described in Section 4. Section 5 identifies two configurations of
interest and develops their corresponding architectures. Section 6 shows a comparison of the two configurations at the
vehicle level, based on subsystem weight. Section 7 compares the two configurations at the mission level, based on fuel
burn. Section 8 contains the conclusions drawn from this work and avenues identified by the authors for future work.
where q̄ is the dynamic pressure, M is the Mach number, αef f is the effective angle of attack seen by the main surface,
δ the control surface deflection, and Sf and cf are the control surface planform area and chord. Ch,0 , Ch,α , and Ch,δ are
hinge moment coefficients representing the effect of main lifting surface camber, αef f , and δ on the hinge moment.
The hinge moment coefficients were determined based on the geometries of the control surfaces and associated main
lifting surfaces using the empirical methodology of Roskam (18). Hinge moments predicted using these coefficients were
validated against published hinge moments from flight tests of the NASA F-18 Systems Research Aircraft (7). This
comparison, shown in Fig. 2, yielded acceptable agreement between predicted and observed hinge moments. For the flight
and ground spoilers, the method proposed by Scholz (19) was used to determine hinge moment coefficients.
Aileron Deflection (deg)
20 20
10 10
0 0
−10 −10
−20 −20
0 1 2 3 4 5 0 1 2 3 4 5 6
Time (s) Time (s)
4000
Hinge Moment (Nm)
2000 Predicted
Flight Test 2000
1000
0 0
−1000
−2000 Predicted
Flight Test
−2000
−4000
0 1 2 3 4 5 0 1 2 3 4 5 6
Time (s) Time (s)
(a) Abrupt roll doublet - full stick (left): M = 0.72, (b) Abrupt aileron reversal - full stick (left): M = 0.84,
h = 7,620 m (25,000 ft), q-bar = 13.60 kPa (284 lbf / ft2 ) h = 7,620 m (25,000 ft), q-bar = 18.29 kPa (382 lbf / ft2 )
Fig. 2. Comparison of hinge moments predicted using Roskam’s method with flight test data from NASA’s F-18 SRA
For each primary control surface, the flight condition (represented by q̄, αef f , and δ) that yields the maximum hinge
moment can be obtained from the relevant Federation Aviation Regulations (FARs), and have been identified by Scholz (19).
400
350
MMO limit
300
Altitude (FL)
250
Elevator
200
& Rudder
150 VMO limit
100
Flt.
Aileron Spoiler
50
Fig. 3. Boeing 737-800 flight envelope with maximum hinge moment flight condition for ailerons, elevators, rudder, and flight spoilers
For the aileron, it is given by FAR 25.349, and corresponds to the maximum hinge moment from among three flight conditions
- abrupt and full deflection at design manuever speed (VA ), a deflection yielding the same roll rate at design cruise speed
(VC ), and a deflection yielding a third of the roll rate at the design dive speed (VD ). For the elevators, FAR 25.255 specifies
the required positive and negative recovery load factors that must be available following a “runaway” failure of the THS. For
the rudder, the applicable FARs are FAR 25.149 (one engine inoperative) and FAR 25.351 (permissible rudder deflections).
FAR 25.351 and FAR 25.255 were evaluated over the aircraft altitude-speed envelope to determine the most critical flight
condition yielding the maximum hinge moment (Fig. 3). For the flight spoilers, the maximum hinge moment occurs when
they are extended during an emergency descent performed at the design dive speed (VD ). Since “weight-on-wheels” is
required for ground spoiler deployment, the maximum rated tire speed was used to compute their actuation load requirement.
High lift device actuating loads strongly depend on flap mechanism kinematics, which vary significantly between both
aircraft and manufacturers (17). In lieu of a detailed analysis of any one mechanism, the maximum actuation loads for the
Krueger flaps and slats were derived using force and moment coefficients from published wind tunnel analyses (20, 21).
For the trailing edge flaps, the required actuation load was set to the ratings of the existing leadscrew type actuators3 .
The maximum angular rates of ailerons, elevators, rudder, and flight spoilers were set based on the observed trend of
higher rate requirements for modern automatic flight control systems (22). Representative rates for the high lift devices
were obtained by timing videos of these devices deploying. Table 1 summarizes the derived actuation requirements.
Table 1. Summary of flight control surface actuation requirements for example small narrowbody aircraft
3 Boeing 737 linear ballscrew flap actuator, Triumph Gear Systems, Triumph Group, Inc., High-Lift Actuation Systems product data-sheet. Available
online: www.triumphgroup.com/companies/triumph-gear-systems-park-city/Documents, accessed Feb 25, 2014.
4. Electrohydrostatic and Electromechanical Actuator Models
Linear type actuators (as opposed to rotary actuators) were considered in this work. The relationship between control
surface angular movement and actuator ram linear movement for hinged control surfaces is governed by the kinematics of
the control surface to actuator linkage (Fig. 4(a)). This allows the actuator’s output force FL , ram speed v, and ram position
x to be computed from the control surface’s hinge moment, angular rate, and angular position.
The actuator is sized based on the required load-speed envelope, shown notionally in Fig. 4(b). Its stall load F0 , no-load
(maximum) speed vmax , and stroke ∆xmax can be computed from the maximum control surface hinge moment Mh,max ,
maximum angular rate δ̇max , control surface angular range ∆δmax , and the linkage kinematics (Fig. 4(a)).
∆x
Airframe
Control surface
Output force, FL
No-load speed
Fsh
ator
Actu ∆δ Steady holding load
Fixed length
Ram speed, v vmax
(a) Actuation of hinged control surface using linear actuator (b) Actuator load vs. speed envelope
Motor Pump
Gearbox
Motor
Ram Ram
1
∆p = (mr ẍ + cẋ + FL ), (2)
Ap
where Ap is the piston cross-sectional area, mr the mass of reciprocating components (piston + output rod + balance
rod), and c the viscous friction coefficient. The required piston area was computed by evaluating Eq. 2 at the stall load
condition and with maximum pressure difference, i.e., with FL = F0 , ẋ = ẍ = 0, ∆p = ∆pmax . Cylinder components
were sized considering the loads applicable for each, e.g., piston rod diameter based on tension/compression and buckling,
cylinder wall thickness based on tensile and circumferential (Hoop) stresses, etc (23). The cylinder mass mc was computed
by summing the computed masses of the constituent components and the enclosed hydraulic fluid, and considering the
cylinder configuration (single or tandem).
The required total pump flow Qtot is given by the sum of the ideal flow Qi and the leakage flow Ql , i.e.
where clkg is the leakage coefficient. The pump shaft speed ωp and required shaft torque τp are given by
Qtot ∆p Dpump
ωp = , τp = , (4)
Dpump ηh
where Dpump is related to the pump displacement4 as Dpump = (pump displacement)/(2π) and ηh is the pump efficiency.
Since the leakage flow is typically much smaller than the ideal flow, the maximum flow rate corresponds to the maximum
ram velocity, i.e. Qmax
tot ≈ Ap vmax . For the EHA, the motor and pump shaft speeds and torques are physically identical,
i.e. ωm = ωp , τm = τp . The required maximum speed and shaft torque of the motor are then given by
A parametric pump model was used to compute the pump mass mp based on the pump displacement. This included the
mass of the hydraulic fluid present within the pump, while the mass of the hydraulic fluid in the lines connecting the pump
to the cylinder was accounted for using the mass calibration factor discussed in a subsequent section.
max max F0
ωm = vmax Gbs Ggb , τm = , (7)
(ηbs Gbs )(ηgb Ggb )
where ηbs and ηgb are the ballscrew and gearbox efficiencies. For this work, a gearbox efficiency of ηgb = 0.9 was used.
The ballscrew efficiency was computed as ηbs = tan αbs / tan(αbs + φbs ), where φbs = tan−1 µbs is the friction angle
and αbs = tan−1 (1/(Gbs rbs )) is the screw helix angle. The radius of the screw rbs was selected as the larger of the radius
computed from buckling consideration and that from consideration of combined axial and torsional loading (23).
4 Pump displacement is defined as the fluid volume pumped per unit revolution (mm3 /rev or in3 /rev).
For the gearbox, the number of stages required to attain the overall gearbox ratio Gbs was computed as n =
ceil log(Ggb )/log(Gmax max
stg ) , where Gstg = 2Lcc /dmin − 1 is the maximum stage reduction ratio for a given center-
to-center distance Lcc and minimum permissible pinion diameter dmin . The gearbox mass mgb was computed after
determining the gear face width from strength considerations (23), and accounting for the number of driver-driven pairs.
1. The peak output torque given by Eq. 5 and Eq. 7 must be met with a torque margin applied to satisfy acceleration
requirements against actuator inertia.
2. The actuator force-speed (F − v) envelope, when reduced to a torque-speed (τ − ω) envelope by the actuator gearing,
must be contained within the motor torque-speed envelope.
3. The motor’s maximum continuous torque must meet the actuator’s steady-holding load requirement.
Evaluating the input electrical power over the boundary of the motor τ − ω envelope (accounting for losses whose
max
magnitudes depend on the operating point in the envelope), the maximum electrical input power Pin was determined.
max max
Torabzadeh-Tari (25) provides an empirical estimate of the mass of a BLDC motor based on τout and Pin as
−0.84
4.7
1222 + 26.7 (f1 − 375)0.28 + 0.98 (Pin
max
− 491)0.11
mem = 10 −3
max [kg] (8)
τout
where f1 is the source fundamental frequency. The same author also provides an estimate for the weight of the power
electronics as
0.02
400
2290 + 0.3 (fsw − 6000)0.8 + 0.3 (Pin − 2000)1.1
mpe = 10 −3
AC
[kg] (9)
Vin
AC
where fsw is the switching frequency, Vin is the input AC voltage (for this work, the actuators are powered from 135 VAC
max
buses), and Pin is obtained by scaling the motor’s maximum input power Pin by the assumed efficiency of the power
electronics. For actuator designs comprising two motors, each was assumed to have its own power electronic unit.
To determine the magnitude of the under-prediction, the masses predicted using Eq. 10 were compared against published
masses of electric actuators available from previous analyses or flight tests. For each such case, the actuator was sized to
the same stall load, no-load rate, and stroke as the published actuators. Additional information regarding the actuator layout
(such as electrohydraulic or electromechanical redundancy) was incorporated whenever available5 . A calibration factor of
1.15 (i.e., + 15 %) applied to the predicted cylinder, pump, ballscrew, and gearbox masses produced reasonable agreement,
as shown in Tables 2 and 3 for EHA and EMA respectively.
Table 2. Comparison of predicted vs. published EHA weight following calibration
5 Abbreviations:
3φ - three phase, PMM - permanent magnet machine, FDP - fixed displacement pump, EH - electrohydraulic, TC - tandem cylinder,
BLDCM - brushless DC motor, BS - ballscrew, SRM - switched reluctance machine, M/P - motor/pump, M/GB - motor/gearbox.
Fig. 6. Weight-optimal EHA and EMA designs vs. sizing hinge moment
requirements are applicable. In fact, EMA design for spoiler actuation was analyzed by Fronista and Bradbury (14) and
Atallah et al. (13). A similar argument holds for the high lift devices, and an EMA-driven high lift system was analyzed
experimentally and from a safety/reliability standpoint by Bennett et al. (15, 28). In line with this reasoning, the two control
surface actuation configurations shown in Fig. 7 were selected for further analysis.
Fig. 7. Configuration 1: T/E flaps actuated by EMA-LS. All other surfaces actuated by EHA. Configuration 2: Ailerons, elevators,
rudder actuated by EHA. L/E slats, Krueger flaps, and spoilers actuated by EMA. T/E flaps actuated by EMA-LS.
• Configuration 1: Other than the trailing-edge flaps (TEFs), all control surfaces are driven by EHAs. Two parallel EHAs
are used to drive each aileron and elevator, while three are used for the rudder. Slats, Krueger flaps, flight spoilers,
and ground spoilers are driven by a single EHA. Each trailing-edge flap is driven by two parallel Electromechanically
Actuated Leadscrews (EMA-LS6 ).
• Configuration 2: The slats, Krueger flaps, flight spoilers, and ground spoilers are each actuated using a single EMA.
Actuation for the remaining control surfaces is identical to Configuration 1.
A detailed functional hazard analysis was beyond the scope of the current work, but design practices from Boeing (29)
and Airbus (30) were adopted to determine the nature of redundancy incorporated into the two architectures.
6 EMA-LS: Electromechanically Actuated Leadscrew. A variant of the EMA in which the nut is the translating member instead of the rotating member.
This is similar to the leadscrews used in the conventional Boeing 737-800 trailing edge flap system.
1. The stringent reliability requirements of the flight-critical primary control surfaces was met using a combination of
actuator redundancy and internal redundancy (31). Actuator redundancy was provided by using two parallel actuators
in active-active configuration for the elevators and ailerons, and three parallel actuators in active-active-standby config-
uration for the rudder. Only EHAs were considered for these surfaces due to their fail-safe characteristics, and parallel
EHAs were powered from different electric buses. Each EHA driving a flight-critical control surface was assumed to
have internal redundancy, in which two motor-pump pairs drove a tandem cylinder (2 M/P → 1 TC).
2. For non flight-critical control surfaces such as spoilers, slats, and Krueger flaps, surface redundancy already existed
since there were multiple panels per wing. In this case, each panel was powered by a single actuator (either EHA
or EMA). The actuators were connected to the electric buses in a way that ensured symmetric availability of control
surfaces following the failure of any one bus.
3. Trailing edge flap panel were provided actuator redundancy, and were driven by two EMA-LS units at the two extremities
(in practice, this also prevents panel warping due to aerodynamic loads), powered from different buses. Each EMA-LS
had internal redundancy (6), in which two motor-gearbox pairs drove a ballscrew through a summing element.
Cruise
(380 min, M 0.75, ICA 33 kft)
Reserve fuel:
Climb Descent 200 NM div.
(18.5 min) (26.2 min) 30 min hold
Fig. 8. Representative flight profile for mission level analysis. In addition to the 3,000 NM (380 min) flight shown, shorter flights of
350 NM (63 min), 850 NM (132 min), and 1,350 NM (202 min) were also evaluated.
To compute the power consumed at the bus by the electric actuator, the control surface hinge moment and angular rate
were converted to the required force (Freq ) and speed (vreq ) at the control/actuator linkage using the control surface gearing
Gcs . These were then propagated through the mathematical model of the actuator to get the required torque (τreq ) and shaft
speed (ωm,req ) of the electric motor, effectively using the overall actuator gearing (Gact ). The motor torque and shaft speed
requirements were then evaluated in conjunction with the assumed torque-speed characteristics of the BLDC motor (24)
to find the motor input power requirement. Finally, this was scaled using the assumed power electronics efficiency ηpe to
give the power draw at the bus7 . This is shown in Eq. 11 for a single-channel actuator.
G G em ηem (τ,ω)
pe ηpe
→ Freq , vreq −−act
Mh , ω −−cs −→ τreq , ωm,req −−−−−−→ Pin −−→ Pin = Pbus (11)
Certain control surface motions (e.g., flap deployment/retraction) occur only during a fraction of the duration of a
mission segment. For these, the average power consumption over the duration of the mission segment P̄seg was computed
7 An alternate method is to estimate the power requirement at the control surface, i.e. the product of hinge moment and angular rate, and then scale
successively by the efficiencies of all actuator components encountered to obtain the power draw at the bus. However, this method will predict zero
power draw from the bus if the control surface is held fixed against a non-zero load, while in reality electric actuators are known to consume power in
this condition. The method described above and used in this analysis does not suffer from this discrepancy.
using the mean power consumed during the motion P̄ and the activity ratio ν as follows:
∆tactive
ν= ∈ [0, 1], =⇒ P̄seg = P̄ ν + 0.(1 − ν) = P̄ ν. (12)
∆tseg
As only the flight control actuation subsystem was being considered, the non-propulsive power requirements of the
other subsystems (Table 6) were assumed to be identical for both configurations. The Environmental Control System (ECS)
was assumed to have a bleedless architecture, and engine bleed air was used only for the cowl ice protection system (IPS),
similar to the Boeing 787 arrangement. The power and bleed air demands of these systems were reported by Tagge et al. (33)
for a Boeing 767-type airplane, and were scaled using guidelines reported by Cleveland (34) to Boeing 737-800 size. Power
demands for instrumentation, communication, navigation (tabulated as ‘instruments’), equipment and furnishings, lights,
pumping fuel, and miscellaneous loads were also set in a similar manner. The power demand for the assumed electrical
wing de-icing system was estimated using a rapid-evaluation method developed by Meier and Scholz (35) which was shown
to have good agreement with the Boeing 787 wing IPS power demand. Centralized hydraulics were assumed to be retained
to actuate the landing gear, landing gear bay doors, brakes, nosewheel steering, and cargo doors. The power consumption
for these users for different flight phases was reported by de Tenorio (36) for the case of the similar-sized Airbus A320,
and has been incorporated as a shaft-power offtake (to run engine-driven hydraulic pumps) in this work.
System Type Unit Ground Takeoff Climb Cruise Descent Landing OEI
ECS Bleedless kVA 129 129 210 210 210 129 204
Instruments Electric kVA 8 8 8 8 8 8 8
Equipment Electric kVA 60 60 60 65 0 0 0
Fuel EMDP kVA 7.5 7.5 7.5 7.5 7.5 7.5 7.5
” EDP kW 7.5 7.5 7.5 7.5 7.5 7.5 7.5
Wing IPS Electric kVA 17 17 25 25 25 17 17
Cowl IPS Bleed air kg/s 2.2 2.2 0 0 2.2 2.2 1.1
Lights Electric kVA 10 10 10 10 10 10 10
Hyd. users EDP kW 1.43 0 0.67 0 0.44 9.83 9.83
Misc. Electric kVA 5 5 5 5 5 5 5
Demand Electric kVA 124 124 171 173 139 92 260
per Mechanical kW 4.9 4.1 4.5 4.1 4.4 9.5 15.2
Engine Bleed kg/s 1.1 1.1 0 0 1.1 1.1 1.1
The propulsion system characteristics were generated using the Environmental Design Space (EDS) tool (37) developed
for the U.S. Federal Aviation Administration’s Office of Environment and Energy (FAA/AEE) and NASA. At the core of
this tool is the Numerical Propulsion System Simulation (NPSS) (38) tool, which was used to generate an engine deck that
is representative of the CFM56-7B27 engine, but does not utilize or contain any proprietary information.
The difference between the two configurations in terms of mission fuel burn may be caused by a difference in either the
non-propulsive power requirement or the subsystem weight. While both effects were considered in this work, the magnitude
of the first was quite small, as seen from Table 7. Further, the peak power demand for flight control actuation (a factor
influencing generator sizing) does not occur for any of the flight conditions of Table 7. Tagge et al. (33) note that this
critical peak power flight condition is generally the one-engine inoperative (OEI) crosswind landing condition, where the
combination of high load and rate requirements justifies a conservative sizing approach based on corner power8 . Referring
to Table 1 and assuming operability of both ailerons, both elevators, the rudder, and four out of eight flight spoilers in the
OEI condition, the combined corner power evaluates to around 51 kW for both configurations.
8 Corner power for a control surface is the product of maximum hinge moment and maximum angular rate.
Table 7. Flight control actuation power requirements for Configurations 1 and 2 (averaged over mission segment duration)
The difference in mission fuel burn is primarily driven by the difference in weight between the two configurations
(Table 4). In addition to the 3,000 NM mission shown in Fig. 8, the fuel burn differences were also evaluated over several
intermediate trip distances more commonly encountered in small narrowbody aircraft operations, and are shown in Table 8.
Acknowledgments
The authors would like to thank Mr. Christopher Perullo, Research Engineer II at the Aerospace Systems Design Laboratory,
for supporting their investigation on the propulsion side with his expertise and experience with the EDS and NPSS tools.
Funding
This research received no specific grant from any funding agency in the public, commercial, or not-for-profit sectors.
References
[1] Raymer, D., Aircraft Design: A Conceptual Approach, AIAA Education Series, 4th ed.
[2] Faleiro, L., “Beyond the More Electric Aircraft,” AIAA Aerospace America, 2005.
[3] Cronin, M., “The all-electric aircraft,” IEE Review, Vol. 36, No. 8, sep 1990, pp. 309 –311.
[4] Jones, R., “The More Electric Aircraft - Assessing the Benefits,” Proceedings of the Institution of Mechanical Engineers, Part G, Journal
of Aerospace Engineering, Vol. 216, 2002, pp. 259–270.
[5] Cloyd, J., “Status of the United States Air Force’s More Electric Aircraft initiative,” Aerospace and Electronic Systems Magazine, IEEE,
Vol. 13, No. 4, April 1998, pp. 17–22.
[6] Thompson, K., “Notes on ’The electric control of large aeroplanes’,” Aerospace and Electronic Systems Magazine, IEEE, Vol. 3, No. 12,
dec. 1988, pp. 19 –24.
[7] Navarro, R., “Performance of an Electro-Hydrostatic Actuator on the F-18 Systems Research Aircraft,” 16th Digital Avionics Systems
Conference, Irvine, California, October 1997.
[8] Jensen, S., Jenney, G., and Dawson, D., “Flight test experience with an electromechanical actuator on the F-18 Systems Research Aircraft,”
19th Digital Avionics Systems Conference, 2000, Vol. 1, 2000, pp. 2E3/1 – 2E310.
[9] Burkhard, A. and Dietrich, R., “Joint Strike Fighter Integrated Subsystems Technology, A Demonstration for Industry, by Industry,”
Journal of Aircraft, Vol. 40, 2003, pp. 906–913.
[10] Vohnout, S., Bodden, D., Kim, B., Wagoner, R., Kunst, N., Edwards, P., Gleeson, B., Cascio, D., Brzuszkiewicz, S., Wagemans, R., Rounds,
M., and Clements, N., “Prognostic-Enabling of an Electrohydrostatic Actuator (EHA) System,” Annual Conference of Prognostics
and Health Management Society, 2012.
[11] Van den Bossche, D., “The A380 Flight Control Electrohydrostatic Actuators, Achievements and Lessons Learnt,” 25th International
Congress of the Aeronautical Sciences, ICAS 2006, 2006.
[12] Kulshreshtha, A. and Charrier, J., “Electric Actuation for Flight and Engine Control: Evolution and Challenges,” SAE-ACGSC Meeting
99, SAE, Feb 28 - Mar 2 2007.
[13] Atallah, K., Caparrelli, F., Bingham, C., Schofield, N., Howe, D., Mellor, P., Maxwell, C., Moorhouse, D., and Whitley, C., “Permanent
magnet brushless drives for aircraft flight control surface actuation,” Electrical Machines and Systems for the More Electric Aircraft
(Ref. No. 1999/180), IEE Colloquium on, 1999, pp. 8/1 –8/5.
[14] Fronista, G. and Bradbury, G., “An electromechanical actuator for a transport aircraft spoiler surface,” Energy Conversion Engineering
Conference, 1997. IECEC-97., Proceedings of the 32nd Intersociety, Vol. 1, 1997, pp. 694–698 vol.1.
[15] Bennett, J., Mecrow, B., Jack, A., and Atkinson, D., “A Prototype Electrical Actuator for Aircraft Flaps,” Industry Applications, IEEE
Transactions on, Vol. 46, No. 3, 2010, pp. 915–921.
[16] Chakraborty, I., Mavris, D., Emeneth, M., and Schneegans, A., “A System and Mission Level Analysis of Electrically Actuated Flight
Control Surfaces using Pacelab SysArc,” AIAA Science and Technology Forum and Exposition (SciTech 2014), National Harbor, MD,
January 13-17 2014.
[17] Rudolph, P., “High Lift Systems on Subsonic Commercial Airliners,” NASA Contractor Report 4746 CONTRACT A46374D(LAS),
National Aeronautics and Space Administration, September 1996 1996.
[18] Roskam, J., Airplane Design Part VI - Preliminary Calculation of Aerodynamic, Thrust and Power Characteristics, Design Analysis &
Research, 1999.
[19] Scholz, D., “Development of a CAE-Tool for the Design of Flight Control and Hydraulic Systems,” AeroTech ’95, Birmingham,, 1995.
[20] Moraris, V., Lawson, N., and Garry, K., “Aerodynamic and Performance Characteristics of a Passive Leading Edge Krueger Flap at Low
Reynolds Numbers,” The Aeronautical Journal, Vol. 116 (1181), 2012, pp. 759–769.
[21] Kelly, J. and McCullough, G., “Aerodynamic Loads on a Leading-edge Flap and a Leading-edge Slat on the NACA 64A010 Airfoil
Section (NACA TN 3220),” Tech. rep., National Advisory Committee for Aeronautics (NACA), 1954.
[22] Charrier, J. and Kulshreshtha, “Electric Actuation for Flight and Engine Control System: Evolution, Current Trends and Future
Challenges,” 45th AIAA Aerospace Sciences Meeting and Exhibit, No. AIAA 2007-1391, Reno, Nevada, January 2007.
[23] Khurmi, R. and Gupta, J., A Textbook of Machine Design, Eurasia Publishing House (Pvt.) Ltd., 2005.
[24] Frischemeier, S., “Electrohydrostatic actuators for aircraft primary flight control - types, modelling and evaluation,” 5th Scandinavian
International Conference on Fluid Power, SICFP 1997, Linkoping, Sweden, May 1997.
[25] Torabzadeh-Tari, M., Dimensioning Tools of MEA Actuator Systems, Including Modeling, Analysis and Technology Comparison, Ph.D.
thesis, KTH Electrical Engineering, 2008.
[26] Sadeghi, T. and Lyons, A., “Fault Tolerant EHA Architectures,” IEEE AES Systems Magazine, March 1992, pp. 32–42.
[27] Botten, S., Whitley, C., and King, A., “Flight Control Actuation Technology for Next-Generation All-Electric Aircraft,” Technology
Review Journal - Millenium Issue, 2000, pp. 55–68.
[28] Bennett, J., Mecrow, B., Atkinson, D., and Atkinson, G., “Safety-critical design of electromechanical actuation systems in commercial
aircraft,” Electric Power Applications, IET , Vol. 5, No. 1, 2011, pp. 37–47.
[29] Yeh, Y., “Triple-triple redundant 777 primary flight computer,” Aerospace Applications Conference, 1996. Proceedings., 1996 IEEE,
Vol. 1, feb 1996, pp. 293 –307 vol.1.
[30] Traverse, P., Lacaze, I., and Souyris, J., “Airbus Fly-by-Wire: A Process Towards Total Dependability,” ICAS 2006, 25th International
Congress of the Aeronautical Sciences, 2006.
[31] Bennett, J., Mecrow, B., Atkinson, D., and Atkinson, G., “Failure mechanisms and design considerations for fault tolerant aerospace
drives,” Electrical Machines (ICEM), 2010 XIX International Conference on, 2010, pp. 1–6.
[32] Simsic, C., “Electric actuation system duty cycles,” Aerospace and Electronics Conference, 1991. NAECON 1991., Proceedings of the
IEEE 1991 National, 1991, pp. 540–545 vol.2.
[33] Tagge, G., Irish, L., and Bailey, A. R., “Systems Study for an Integrated Digital/Electric Aircraft (IDEA).” NASA Contractor Report
3840, January 1985.
[34] Cleveland, F., “Size Effects in Conventional Aircraft Design,” Journal of Aircraft, Vol. 7, No. 6, Nov-Dec 1970, pp. 483–512.
[35] Meier, O. and Scholz, D., “A Handbook Method for the Estimation of Power Requirements for Electrical De-Icing Systems,” DLRK,
Hamburg, Aug. 31 - Sept. 2 2010.
[36] de Tenorio, C., Method for Collaborative Conceptual Design of Aircraft Power Architectures, Ph.D. thesis, Georgia Institute of Technology,
Atlanta, GA, USA, 2010.
[37] Kirby, M. and Mavris, D., “The Environmental Design Space,” 26th International Congress of the Aeronautical Sciences (ICAS),
Anchorage, Alaska, September 14-19 2008.
[38] “Numerical Propulsion System Simulation (NPSS): An Award Winning Propulsion System Simulation Tool,” Online:
https://www.grc.nasa.gov/WWW/RT/RT2001/9000/9400naiman.html.