KA01309D/06/EN/02.

18
71399862
Products Solutions Services
2018-08-01

Brief Operating Instructions

Proline 300
HART
Transmitter with Coriolis sensor

These instructions are Brief Operating Instructions; they are

not a substitute for the Operating Instructions pertaining to
the device.
Transmitter Brief Operating Instructions
Contain information about the transmitter.
Sensor Brief Operating Instructions →  3
 Proline 300 HART

Order code: XXXXX-XXXXXX

1. Ser. no.: XXXXXXXXXXXX
Ext. ord. cd.: XXX.XXXX.XX

Serial number

2. www.endress.com/deviceviewer Endress+Hauser
Operations App

3.

A0023555

2 Endress+Hauser
Proline 300 HART Brief Operating Instructions for the device

Brief Operating Instructions for the device

The device consists of a transmitter and a sensor.
The process of commissioning these two components is described in two separate manuals:
• Sensor Brief Operating Instructions
• Transmitter Brief Operating Instructions
Please refer to both Brief Operating Instructions when commissioning the device as the
contents of the manuals complement one another:
Sensor Brief Operating Instructions
The Sensor Brief Operating Instructions are aimed at specialists with responsibility for
installing the measuring device.
• Incoming acceptance and product identification
• Storage and transport
• Installation
Transmitter Brief Operating Instructions
The Transmitter Brief Operating Instructions are aimed at specialists with responsibility for
commissioning, configuring and parameterizing the measuring device (until the first
measured value).
• Product description
• Installation
• Electrical connection
• Operation options
• System integration
• Commissioning
• Diagnostic information

Additional device documentation

These Brief Operating Instructions are the Transmitter Brief Operating Instructions.
The "Sensor Brief Operating Instructions" are available via:
• Internet: www.endress.com/deviceviewer
• Smart phone/tablet: Endress+Hauser Operations App
Detailed information about the device can be found in the Operating Instructions and the
other documentation:
• Internet: www.endress.com/deviceviewer
• Smart phone/tablet: Endress+Hauser Operations App

Endress+Hauser 3
Table of contents Proline 300 HART

Table of contents
1 Document information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Basic safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Requirements for the personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.6 IT security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7 Device-specific IT security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1 Turning the transmitter housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Turning the display module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3 Cover locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.4 Transmitter post-installation check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1 Connection conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2 Connecting the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3 Ensuring potential equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.4 Ensuring the degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6 Operation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.1 Overview of operation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2 Structure and function of the operating menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.3 Access to the operating menu via the local display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.4 Access to the operating menu via the operating tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5 Access to the operating menu via the Web server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

7 System integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

8 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.2 Setting the operating language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.3 Configuring the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.4 Protecting settings from unauthorized access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

9 Diagnostic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4 Endress+Hauser
Proline 300 HART Document information

1 Document information
1.1 Symbols used
1.1.1 Safety symbols

Symbol Meaning

DANGER!
DANGER This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.

WARNING!
WARNING This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.

CAUTION!
CAUTION This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.

NOTE!
NOTICE This symbol contains information on procedures and other facts which do not result in
personal injury.

1.1.2 Symbols for certain types of information

Symbol Meaning Symbol Meaning

Permitted Preferred
Procedures, processes or actions that Procedures, processes or actions that
are permitted. are preferred.

Forbidden Tip
Procedures, processes or actions that Indicates additional information.
are forbidden.

Reference to documentation A Reference to page

Reference to graphic 1. , 2. , 3. … Series of steps

Result of a step Visual inspection

1.1.3 Electrical symbols

Symbol Meaning Symbol Meaning

Direct current Alternating current

Direct current and alternating current Ground connection

A grounded terminal which, as far as
the operator is concerned, is grounded
via a grounding system.

Endress+Hauser 5
Document information Proline 300 HART

Symbol Meaning

Protective Earth (PE)

A terminal which must be connected to ground prior to establishing any other connections.
The ground terminals are situated inside and outside the device:
• Inner ground terminal: Connects the protectiv earth to the mains supply.
• Outer ground terminal: Connects the device to the plant grounding system.

1.1.4 Communication symbols

Symbol Meaning Symbol Meaning

Wireless Local Area Network LED

(WLAN) Light emitting diode is off.
Communication via a wireless, local
network.

LED LED
Light emitting diode is on. Light emitting diode is flashing.

1.1.5 Tool symbols

Symbol Meaning Symbol Meaning

Torx screwdriver Flat blade screwdriver

Cross-head screwdriver Allen key

Open-ended wrench

1.1.6 Symbols in graphics

Symbol Meaning Symbol Meaning

1, 2, 3,... Item numbers 1. , 2. , 3. … Series of steps

A, B, C, ... Views A-A, B-B, C-C, ... Sections

Hazardous area Safe area (non-hazardous area)

- .
Flow direction

6 Endress+Hauser
Proline 300 HART Basic safety instructions

2 Basic safety instructions

2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
‣ Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣ Are authorized by the plant owner/operator.
‣ Are familiar with federal/national regulations.
‣ Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the application).
‣ Follow instructions and comply with basic conditions.

2.2 Designated use

Application and media
• The measuring device described in these Brief Operating Instructions is intended only for
flow measurement of liquids and gases.
• The measuring device described in these Brief Operating Instructions is intended only for
flow measurement of liquids.

Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or where there is an
increased risk due to process pressure, are labeled accordingly on the nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣ Keep within the specified pressure and temperature range.
‣ Only use the measuring device in full compliance with the data on the nameplate and the
general conditions listed in the Operating Instructions and supplementary documentation.
‣ Based on the nameplate, check whether the ordered device is permitted for the intended
use in the hazardous area (e.g. explosion protection, pressure vessel safety).
‣ Use the measuring device only for media to which the process-wetted materials are
sufficiently resistant.
‣ If the ambient temperature of the measuring device is outside the atmospheric
temperature, it is absolutely essential to comply with the relevant basic conditions as
specified in the device documentation.
‣ Protect the measuring device permanently against corrosion from environmental
influences.

Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage caused
by improper or non-designated use.

LWARNING
Danger of breakage due to corrosive or abrasive fluids and ambient conditions!
‣ Verify the compatibility of the process fluid with the sensor material.
‣ Ensure the resistance of all fluid-wetted materials in the process.
‣ Keep within the specified pressure and temperature range.
Endress+Hauser 7
Basic safety instructions Proline 300 HART

NOTICE
Verification for borderline cases:
‣ For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in
verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.

Residual risks

LWARNING
The electronics and the medium may cause the surfaces to heat up. This presents a burn
hazard!
‣ For elevated fluid temperatures, ensure protection against contact to prevent burns.
Only applies for Proline Promass A, E, F, O, X and Cubemass C

LWARNING
Danger of housing breaking due to measuring tube breakage!
If a measuring tube ruptures, the pressure inside the sensor housing will rise according to the
operating process pressure.
‣ Use a rupture disk.
LWARNING
Danger from medium escaping!
For device versions with a rupture disk: medium escaping under pressure can cause injury or
material damage.
‣ Take precautions to prevent injury and material damage if the rupture disk is actuated.

2.3 Workplace safety

For work on and with the device:
‣ Wear the required personal protective equipment according to federal/national
regulations.

For welding work on the piping:

‣ Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣ Due to the increased risk of electric shock, gloves must be worn.

2.4 Operational safety

Risk of injury.
‣ Operate the device in proper technical condition and fail-safe condition only.
‣ The operator is responsible for interference-free operation of the device.

8 Endress+Hauser
Proline 300 HART Basic safety instructions

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which it
is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms
this by affixing the CE mark to the device.

2.6 IT security
Our warranty is valid only if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the settings.
IT security measures, which provide additional protection for the device and associated data
transfer, must be implemented by the operators themselves in line with their security
standards.

2.7 Device-specific IT security

The device offers a range of specific functions to support protective measures on the operator's
side. These functions can be configured by the user and guarantee greater in-operation safety
if used correctly.
For detailed information on device-specific IT security, see the Operating Instructions for
the device.

2.7.1 Access via service interface (CDI-RJ45)

The device can be connected to a network via the service interface (CDI-RJ45). Device-specific
functions guarantee the secure operation of the device in a network.
The use of relevant industrial standards and guidelines that have been defined by national
and international safety committees, such as IEC/ISA62443 or the IEEE, is recommended.
This includes organizational security measures such as the assignment of access authorization
as well as technical measures such as network segmentation.

Endress+Hauser 9
Product description Proline 300 HART

3 Product description
The device consists of a Proline 300 transmitter and a Proline Promass or Cubemass
Coriolis sensor.
The device is available as a compact version:
The transmitter and sensor form a mechanical unit.

1 2 3 4

Ni
Spcht Pow
an un
Do nu te er
en no ngr

öf
er t öf

f ne
Ne gi op fn
so pa zeden when

n
us s ou
tens vr en
ionir

ter
I/O

un
la y Nicht
i sp
D

ar

ES
C
–

5
A0029586

1 Connection compartment cover

2 Display module
3 Transmitter housing
4 Electronics compartment cover
5 Sensor

Use of the device with the remote display and operating module DKX001 →  22.

For detailed information on the product description, see the Operating Instructions for
the device

10 Endress+Hauser
Proline 300 HART Installation

4 Installation
For detailed information about mounting the sensor, see the Sensor Brief Operating
Instructions →  3

4.1 Turning the transmitter housing

To provide easier access to the connection compartment or display module, the transmitter
housing can be turned.

4.

öf
öf

f ne
f ne

n
n

te r
te r

un
un

Nicht
Nicht

ES
ES C
C
– –

+ +

E E

e
e

ar ar

3 mm 1. 4 mm 3.
2.

A0029993

1. Depending on the device version: Loosen the securing clamp of the connection
compartment cover.
2. Unscrew the connection compartment cover.
3. Release the fixing screw.
4. Turn the housing to the desired position.
5. Firmly tighten the securing screw.
6. Screw on the connection compartment cover
7. Depending on the device version: Attach the securing clamp of the connection
compartment cover.

Endress+Hauser 11
Installation Proline 300 HART

4.2 Turning the display module

The display module can be turned to optimize display readability and operability.

öf
öf

f ne
f ne

n
n

te r
te r

un
un

Nicht
Nicht

ES
ES C
C
– –

+ +
ES
C
E – E

e
e

ar ar

3 mm 1. 3.
2.

A0030035

1. Depending on the device version: Loosen the securing clamp of the connection
compartment cover.
2. Unscrew the connection compartment cover.
3. Turn the display module to the desired position: max. 8 × 45° in each direction.
4. Screw on the connection compartment cover.
5. Depending on the device version: Attach the securing clamp of the connection
compartment cover.

12 Endress+Hauser
Proline 300 HART Installation

4.3 Cover locking

NOTICE
Order code for "Housing", option L "Cast, stainless": The covers of the transmitter
housing are provided with a borehole to lock the cover.
The cover can be locked using screws and a chain or cable provided by the customer.
‣ It is recommended to use stainless steel cables or chains.
‣ If a protective coating is applied, it is recommended to use a heat shrink tube to protect the
housing paint.

1
1

1
2 SW 2.5
5 (0.2) min. 15 (0.6)
M3

A0029800

1 Cover borehole for the securing screw

2 Securing screw to lock the cover

4.4 Transmitter post-installation check

The post-installation check must always be performed after the following tasks:
• Turning the transmitter housing
• Turning the display module

Is the device undamaged (visual inspection)? 

Turning the transmitter housing:
• Is the securing screw firmly tightened?

• Is the connection compartment cover screwed on tightly?
• Is the securing clamp firmly tightened?
Turning the display module:
• Is the connection compartment cover screwed on tightly? 
• Is the securing clamp firmly tightened?

Endress+Hauser 13
Electrical connection Proline 300 HART

5 Electrical connection
NOTICE
The measuring device does not have an internal circuit breaker.
‣ For this reason, assign the measuring device a switch or power-circuit breaker so that the
power supply line can be easily disconnected from the mains.
‣ Although the measuring device is equipped with a fuse, additional overcurrent protection
(maximum 10 A) should be integrated into the system installation.

5.1 Connection conditions

5.1.1 Required tools
• For cable entries: Use corresponding tools
• For securing clamp: Allen key 3 mm
• Wire stripper
• When using stranded cables: Crimper for wire end ferrule
• For removing cables from terminal: Flat blade screwdriver ≤ 3 mm (0.12 in)

5.1.2 Requirements for connecting cable

The connecting cables provided by the customer must fulfill the following requirements.

Electrical safety
In accordance with applicable federal/national regulations.

Protective ground cable

Cable ≥2.08 mm2 (14 AWG)
The grounding impedance must be less than 1 Ω.

Permitted temperature range

• The installation guidelines that apply in the country of installation must be observed.
• The cables must be suitable for the minimum and maximum temperatures to be expected.

Power supply cable

Standard installation cable is sufficient.

Cable diameter
• Cable glands supplied:
M20 × 1.5 with cable ⌀ 6 to 12 mm (0.24 to 0.47 in)
• Spring-loaded terminals: Suitable for strands and strands with ferrules.
Conductor cross-section 0.2 to 2.5 mm2 (24 to 12 AWG).

14 Endress+Hauser
Proline 300 HART Electrical connection

Signal cable
Current output 4 to 20 mA HART
A shielded cable is recommended. Observe grounding concept of the plant.
Current output 0/4 to 20 mA
Standard installation cable is sufficient.
Pulse/frequency/switch output
Standard installation cable is sufficient.
Double pulse output
Standard installation cable is sufficient.
Relay output
Standard installation cable is sufficient.
Current input 0/4 to 20 mA
Standard installation cable is sufficient.
Status input
Standard installation cable is sufficient.

Requirements for the connecting cable

Optionally available connecting cable

A cable is supplied depending on the order option
• Order code for measuring device: order code 030 for "Display; operation", option O
or
• Order code for measuring device: order code 030 for "Display; operation", option M
and
• Order code for DKX001: order code 040 for "Cable", option A, B, D, E

Standard cable 2 × 2 × 0.34 mm2 (22 AWG) PVC cable with common shield (2 pairs, pair-stranded)

Flame resistance According to DIN EN 60332-1-2

Oil-resistance According to DIN EN 60811-2-1

Shielding Tin-plated copper-braid, optical cover ≥ 85 %

Capacitance: core/shield ≤200 pF/m

L/R ≤24 µH/Ω

Available cable length 5 m (15 ft)/10 m (35 ft)/20 m (65 ft)/30 m (100 ft)

Operating temperature When mounted in a fixed position: –50 to +105 °C (–58 to +221 °F); when cable can
move freely: –25 to +105 °C (–13 to +221 °F)

Endress+Hauser 15
Electrical connection Proline 300 HART

Standard cable - customer-specific cable

No cable is supplied, and it must be provided by the customer (up to max. 300 m (1 000 ft))
for the following order option:
Order code for DKX001: Order code 040 for "Cable", option 1 "None, provided by customer, max
300 m"
A standard cable can be used as the connecting cable.

Standard cable 4 cores (2 pairs); pair-stranded with common shield

Shielding Tin-plated copper-braid, optical cover ≥ 85 %

Capacitance: core/shield Maximum 1 000 nF for Zone 1, Class I, Division 1

L/R Maximum 24 µH/Ω for Zone 1, Class I, Division 1

Cable length Maximum 300 m (1 000 ft), see the following table

Max. cable length for use in

Non-hazardous area,
Cross-section
Ex Zone 2, Class I, Division 2
Ex Zone 1, Class I, Division 1

0.34 mm2 (22 AWG) 80 m (270 ft)

0.50 mm2 (20 AWG) 120 m (400 ft)

0.75 mm2 (18 AWG) 180 m (600 ft)

1.00 mm2 (17 AWG) 240 m (800 ft)

1.50 mm2 (15 AWG) 300 m (1 000 ft)

16 Endress+Hauser
Proline 300 HART Electrical connection

5.1.3 Terminal assignment

Transmitter: supply voltage, input/outputs

Supply voltage Input/output 1 Input/output 2 Input/output 3

1 (+) 2 (–) 26 (+) 27 (–) 24 (+) 25 (–) 22 (+) 23 (–)

Device-specific terminal assignment: adhesive label in terminal cover.

Terminal assignment of the remote display and operating module →  22.

5.1.4 Preparing the measuring device

NOTICE
Insufficient sealing of the housing!
Operational reliability of the measuring device could be compromised.
‣ Use suitable cable glands corresponding to the degree of protection.
1. Remove dummy plug if present.
2. If the measuring device is supplied without cable glands:
Provide suitable cable gland for corresponding connecting cable.
3. If the measuring device is supplied with cable glands:
Observe requirements for connecting cables →  14.

5.2 Connecting the measuring device

NOTICE
Limitation of electrical safety due to incorrect connection!
‣ Have electrical connection work carried out by appropriately trained specialists only.
‣ Observe applicable federal/national installation codes and regulations.
‣ Comply with local workplace safety regulations.
‣ Always connect the protective ground cable  before connecting additional cables.
‣ For use in potentially explosive atmospheres, observe the information in the device-specific
Ex documentation.

Endress+Hauser 17
Electrical connection Proline 300 HART

5.2.1 Connecting the transmitter

1
2
3
4

A0026781

1 Terminal connection for supply voltage

2 Terminal connection for signal transmission, input/output
3 Terminal connection for signal transmission, input/output or terminal connection for network
connection via service interface (CDI-RJ45); optional: connection for external WLAN antenna or
remote display and operating module DKX001
4 Protective earth (PE)

3.

öf
öf

f ne
f ne

n
n

te r
ter

un
un

Nicht
Nicht

ES
ES C
C
– –

+ +

E E

ES
C
–

e
e

ar + ar

4. E

3 mm 1. 3.
2.

A0029813

1. Loosen the securing clamp of the connection compartment cover.

2. Unscrew the connection compartment cover.
3. Squeeze the tabs of the display module holder together.
4. Remove the display module holder.

18 Endress+Hauser
Proline 300 HART Electrical connection

Ni Ni
Spcht Pow Spcht Pow
an un an un
Do nu te er Do nu te er
en no ngr en no ngr

öf

öf
er t

f ne
er t

f ne
öf öf
Ne gi op fn Ne gi op fn
so pa zeden when so pa zeden when

n
us s ou er us s ou
tens vr en tens vr en
ionir Powr en ionir
te fn n
un g öf whe

te r

te r
I/O ichtnnun en I/O

un

un
Npa t op

6. S noze d vrir
Doergis ouion

Nicht

Nicht
ene patens
N us
so
I/O

e
ar ar

ES ES
C C
– –

+ +

E E

5.

A0029814

5. Attach the holder to the edge of the electronics compartment.

6. Open the terminal cover.

8.
7. 10 (0.4)
öf
f ne
n
ter
un
Nicht

mm (in)
e

ar

ES
C
–

9. E

A0029815

7. Push the cable through the cable entry . To ensure tight sealing, do not remove the
sealing ring from the cable entry.
8. Strip the cable and cable ends. In the case of stranded cables, also fit ferrules.
9. Connect the protective ground.

Endress+Hauser 19
Electrical connection Proline 300 HART

11.

öf
f ne
n
22 mm

te r
un
Nicht
24 mm

e
ar

ES
C
–

10.

A0029816

10. Connect the cable in accordance with the terminal assignment .

 Signal cable terminal assignment: The device-specific terminal assignment is
documented on an adhesive label in the terminal cover.
Supply voltage terminal assignment: Adhesive label in the terminal cover or
→  17.
11. Firmly tighten the cable glands.
 This concludes the cable connection process.
12. Close the terminal cover.
13. Fit the display module holder in the electronics compartment.
14. Screw on the connection compartment cover.
15. Secure the securing clamp of the connection compartment cover.

20 Endress+Hauser
Proline 300 HART Electrical connection

Removing a cable

3 (0.12)

1.

2.

A0029598

1 Engineering unit mm (in)

1. To remove a cable from the terminal, use a flat-blade screwdriver to push the slot
between the two terminal holes
2. while simultaneously pulling the cable end out of the terminal.

Endress+Hauser 21
Electrical connection Proline 300 HART

5.2.2 Connecting the remote display and operating module DKX001

The remote display and operating module DKX001 is available as an optional extra .
• The remote display and operating module DKX001 is only available for the following
housing version: order code for "Housing": option A "Aluminum, coated"
• The remote display and operating module DKX001 is only available for the following
housing versions, order code for "Housing":
– Option A "Aluminum, coated"
– Option L "Cast, stainless"
• The measuring device is always supplied with a dummy cover when the remote display
and operating module DKX001 is ordered directly with the measuring device. Display
or operation at the transmitter is not possible in this case.
• If ordered subsequently, the remote display and operating module DKX001 may not be
connected at the same time as the existing measuring device display module. Only one
display or operation unit may be connected to the transmitter at any one time.

Gnd
Vcc
A B
81 82 83 84
1
2

3
81 82 83 84
4
Gnd

A B
Vcc

A0027518

1 Remote display and operating module DKX001

2 Protective earth (PE)
3 Connecting cable
4 Measuring device
5 Protective earth (PE)

5.3 Ensuring potential equalization

5.3.1 Requirements
No special measures for potential equalization are required.
For devices intended for use in hazardous locations, please observe the guidelines in the
Ex documentation (XA).

22 Endress+Hauser
Proline 300 HART Electrical connection

5.4 Ensuring the degree of protection

The measuring device fulfills all the requirements for the IP66/67 degree of protection, Type
4X enclosure.

To guarantee IP66/67 degree of protection, Type 4X enclosure, carry out the following steps
after the electrical connection:
1. Check that the housing seals are clean and fitted correctly.
2. Dry, clean or replace the seals if necessary.
3. Tighten all housing screws and screw covers.
4. Firmly tighten the cable glands.
5. To ensure that moisture does not enter the cable entry:
Route the cable so that it loops down before the cable entry ("water trap").


A0029278

6. Insert dummy plugs into unused cable entries.

5.5 Post-connection check

Are cables or the device undamaged (visual inspection)? 
Do the cables used meet the requirements? 
Do the cables have adequate strain relief? 
Are all the cable glands installed, firmly tightened and leak-tight? Cable run with "water trap" →  23? 
If supply voltage is present, do values appear on the display module? 

Endress+Hauser 23
Operation options Proline 300 HART

6 Operation options
6.1 Overview of operation options

ESC

- + E

1 2 3 4 5 6
A0034513

1 Local operation via display module

2 Computer with Web browser (e.g. Internet Explorer) or with operating tool (e.g. FieldCare, DeviceCare,
AMS Device Manager, SIMATIC PDM)
3 Field Xpert SFX350 or SFX370
4 Field Xpert SMT70
5 Mobile handheld terminal
6 Control system (e.g. PLC)

24 Endress+Hauser
Proline 300 HART Operation options

6.2 Structure and function of the operating menu

6.2.1 Structure of the operating menu

Operating menu for operators and maintenances

Operator
Language !
Maintenance

Operation
task-oriented
Setup
Diagnostics

Operating menu for experts

Expert

Expert function-oriented

A0014058-EN

2 Schematic structure of the operating menu

6.2.2 Operating philosophy

The individual parts of the operating menu are assigned to certain user roles (operator,
maintenance etc.). Each user role contains typical tasks within the device lifecycle.
For detailed information on the operating philosophy, see the Operating Instructions for
the device.
Only applies for Proline Promass F, O, Q and X
For custody transfer, once the device has been put into circulation or sealed, its operation
is restricted.

Endress+Hauser 25
Operation options Proline 300 HART

6.3 Access to the operating menu via the local display

1 2 XXXXXXX 2.1
2.3 19.184 mA
2.2
12.5 2.4
2.6 l/s
2.5

1.1 XXXXXXX S 1.4 3 Language 3.1

à English
1.2 20.50 1.5 Deutsch
Español 3.2
Français
1.3 mA 1.6
ESC

E 4 Xxxxxxx
A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z

1.7 5 +0.000 Xx
0 1 2 3 4
5 6 7 8 9
+ –

A0014013

1 Operational display with measured value shown as "1 value, max." (example)
1.1 Device tag
1.2 Display area for measured values (4-line)
1.3 Explanatory symbols for measured value: Measured value type, measuring channel number, symbol
for diagnostic behavior
1.4 Status area
1.5 Measured value
1.6 Unit for the measured value
1.7 Operating elements
2 Operational display with measured value shown as "1 bar graph + 1 value" (example)
2.1 Bar graph display for measured value 1
2.2 Measured value 1 with unit
2.3 Explanatory symbols for measured value 1: measured value type, measuring channel number
2.4 Measured value 2
2.5 Unit for measured value 2
2.6 Explanatory symbols for measured value 2: measured value type, measuring channel number
3 Navigation view: picklist of a parameter
3.1 Navigation path and status area
3.2 Display area for navigation:  designates the current parameter value
4 Editing view: text editor with input mask
5 Editing view: numeric editor with input mask

26 Endress+Hauser
Proline 300 HART Operation options

6.3.1 Operational display

Explanatory symbols for the measured value Status area

• Depends on the device version, e.g.: The following symbols appear in the status area of the
– : Volume flow operational display at the top right:
– : Mass flow • Status signals
– : Density – F: Failure
– G: Conductivity – C: Function check
– : Temperature – S: Out of specification
• : Totalizer – M: Maintenance required
• : Output • Diagnostic behavior
• : Input – : Alarm
• : Measurement channel number 1) – : Warning
• Diagnostic behavior 2) • : Locking (locked via hardware))
– : Alarm • : Communication via remote operation is active.
– : Warning

1) If there is more than one channel for the same measured variable type (totalizer, output etc.).
2) For a diagnostic event that concerns the displayed measured variable.

6.3.2 Navigation view

Status area Display area

The following appears in the status area of the navigation • Icons for menus
view in the top right corner: – : Operation
• In the submenu – : Setup
– The direct access code for the parameter you are – : Diagnostics
navigating to (e.g. 0022-1) – : Expert
– If a diagnostic event is present, the diagnostic • ▸: Submenus
behavior and status signal • : Wizards
• In the wizard • : Parameters within a wizard
If a diagnostic event is present, the diagnostic behavior • : Parameter locked
and status signal

6.3.3 Editing view

Text editor Correction symbols under

Confirms selection. Clears all entered characters.

Exits the input without applying the changes. Moves the input position one position to the
right.

Clears all entered characters. Moves the input position one position to the left.

Switches to the selection of the correction tools. Deletes one character immediately to the left of
the input position.

Aa1 Toggle
• Between upper-case and lower-case letters
• For entering numbers
• For entering special characters

Endress+Hauser 27
Operation options Proline 300 HART

Numeric editor

Confirms selection. Moves the input position one position to the left.

Exits the input without applying the changes. . Inserts decimal separator at the input position.

– Inserts minus sign at the input position. Clears all entered characters.

6.3.4 Operating elements

Keys and meaning

Enter key

For operational display

• Pressing the key briefly opens the operating menu.
• Pressing the key for 2 s opens the context menu.
In a menu, submenu
• Pressing the key briefly
– Opens the selected menu, submenu or parameter.
– Starts the wizard.
– If help text is open:
Closes the help text of the parameter.
• Pressing the key for 2 s for parameter:
If present, opens the help text for the function of the parameter.
With a wizard: Opens the editing view of the parameter.
With a text and numeric editor:
• Pressing the key briefly
– Opens the selected group.
– Carries out the selected action.
• Pressing the key for 2 s:
Confirms the edited parameter value.

Minus key

• In a menu, submenu: Moves the selection bar upwards in a choose list.

• With a wizard: Confirms the parameter value and goes to the previous parameter.
• With a text and numeric editor: Moves the selection bar to the left (backwards) in an input screen.

Plus key

• In a menu, submenu: Moves the selection bar downwards in a choose list.

• With a wizard: Confirms the parameter value and goes to the next parameter.
• With a text and numeric editor: Moves the selection bar to the right (forwards) in an input screen.

+ Escape key combination (press keys simultaneously)

In a menu, submenu
• Pressing the key briefly
– Exits the current menu level and takes you to the next higher level.
– If help text is open, closes the help text of the parameter.
• Pressing the key for 2 s for the parameter: Returns you to the operational display ("home position").
With a wizard: Exits the wizard and takes you to the next higher level.
With a text and numeric editor: Closes the text or numeric editor without applying changes.

+ Minus/Enter key combination (press the keys simultaneously)

28 Endress+Hauser
Proline 300 HART System integration

Keys and meaning

Reduces the contrast (brighter setting).

+ Plus/Enter key combination (press and hold down the keys simultaneously)

Increases the contrast (darker setting).

+ + Minus/Plus/Enter key combination (press the keys simultaneously)

For operational display:Enables or disables the keypad lock.

6.3.5 Further information

For further information on the following topics, see the Operating Instructions for the
device
• Calling up help text
• User roles and related access authorization
• Disabling write protection via access code
• Enabling and disabling the keypad lock

6.4 Access to the operating menu via the operating tool

The operating menu can also be accessed via the FieldCare and DeviceCare operating
tools. See the Operating Instructions for the device.

6.5 Access to the operating menu via the Web server

The operating menu can also be accessed via the Web server. See the Operating
Instructions for the device.

7 System integration
For detailed information on system integration, see the Operating Instructions for the
device.
• Overview of device description files:
– Current version data for the device
– Operating tools
• Measured variables via HART protocol
• Burst mode functionality in accordance with HART 7 Specification

8 Commissioning
8.1 Function check
Before commissioning the measuring device:
‣ Make sure that the post-installation and post-connection checks have been performed.
Endress+Hauser 29
Commissioning Proline 300 HART

• "Post-installation check" checklist →  13

• "Post-connection check" checklist →  23

8.2 Setting the operating language

Factory setting: English or ordered local language

XXXXXXXXX

20.50
XX XX
Main menu 0104-1
1. Display language
English
Operation
Setup
Display language 0104-1
2. Ã English
Deutsch
Español
Français
Display language 0104-1
3. Ã English
Deutsch
Español
Français
Hauptmenü 0104-1
4. Sprache
Deutsch
Betrieb
Setup

A0029420

3 Taking the example of the local display

8.3 Configuring the measuring device

The Setup menu with its submenus and guided wizards is used for fast commissioning of the
device. They contain all the parameters required for configuration, such as for measurement
or communication.
Depending on the device version, not all submenus and parameters are available in every
device. The selection can vary depending on the order code.

30 Endress+Hauser
Proline 300 HART Commissioning

Example: Available submenus, wizards Meaning

System units Configure the units for all measured values

Medium selection Define the medium

I/O configuration User configurable I/O module

Current input Configuration of the input/output type

Status input

Current output 1 to n

Pulse/frequency/switch output 1 to n

Relay output

Double pulse output

User interface Configure the display format on the local display

Low flow cut off Set the low flow cut off

Partially filled pipe detection Configure partial and empty pipe detection

Advanced setup Additional parameters for configuration:

• Calculated process variables
• Sensor adjustment
• Totalizer
• User interface
• WLAN settings
• Data backup
• Administration

8.4 Protecting settings from unauthorized access

The following write protection options exist in order to protect the configuration of the
measuring device from unintentional modification:
• Protect access to parameters via access code
• Protect access to local operation via key locking
• Protect access to measuring device via write protection switch
For detailed information on protecting the settings against unauthorized access, see the
Operating Instructions for the device.
For detailed information on protecting the settings against unauthorized access in
custody transfer applications, see the Special Documentation for the device.

Endress+Hauser 31
Diagnostic information Proline 300 HART

9 Diagnostic information
Faults detected by the self-monitoring system of the measuring device are displayed as a
diagnostic message in alternation with the operational display. The message about remedial
measures can be called up from the diagnostic message, and contains important information
on the fault.

XXXXXXXXX S XXXXXXXXX S

20.50 S801
Supply voltage

X XX i Menu

1.

Diagnostic list S
Diagnostics 1
1 S801 Supply voltage
Diagnostics 2
Diagnostics 3

2.

2 Supply voltage (ID:203) 3

4 S801 0d00h02m25s 5
Increase supply voltage
6

3.
A0029431-EN

4 Message about remedial measures

1 Diagnostic information
2 Short text
3 Service ID
4 Diagnostic behavior with diagnostic code
5 Operation time of occurrence
6 Remedial measures

1. The user is in the diagnostic message.

Press  ( symbol).
 The Diagnostic list submenu opens.
2. Select the desired diagnostic event with  or  and press  .
 The message about the remedial measures opens.
3. Press  +  simultaneously.
 The message about the remedial measures closes.

32 Endress+Hauser
www.addresses.endress.com