Professional Documents
Culture Documents
5SU13541RC16
5SU13541RC16
Betagard
www.siemens.com/industry s
1/1
Index
1/16 Dimensions
1/2
Betagard Miniature Circuit Breakers
& Betagard DC Circuit Breakers
1/16 Dimensions
1/3
1/1
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Overview
1/4
1/2
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Overview
As per IEC
60898 / IS 8828 As per IEC 60947-2 As per UL 489
Rated 1P, 2P, 3P, 4P 1P 2P, 3P, 4P 1P, 2P, 3P, 4P 1P, 2P, 3P, 4P
Current In (A) 230V AC, 415V 230V AC 230V AC, 415 AC, 415 AC,
Icn (kA) Icn (kA) Icn (kA) Icn (kA) Icn (kA)
5SX4 0.5 - 6 10 50 50 50 50
10 - 20 10 25 30 25 50
25 - 32 10 20 25 20 50
40 - 63 10 10 15 10 –
1/5
1/3
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Overview
Effect of Higher Operating Voltages networks. An overcurrent device must be provided at each
reduction of the conductor cross section. This results in a
Betagard MCB is designed to operate at 240/415V, 50Hz.
cascade graded according to the rated current, which
However the device can operate at 480V, 50Hz with a
should, where possible, provide selectivity.
reduction in breaking capacity of 50%.
Selectivity means, that in the event of a fault, only the
DC Operation protective device in the vicinity of the fault trips. Thus,
Single pole MCBs can be used up to 60V DC and double parallel current paths can continue to provide the
pole up to 110V DC. necessary power.
However, they should not be used below 18V DC. Though For MCBs with upstream fuses, the selectivity limit
the thermal operation is delayed but this is negligible. The essentially depends on the current limits and tripping
instantaneous tripping characteristic must be increased by characteristics of the MCB as well as on the pre-arcing I²t
40% (e.g. a Type ‘C’ MCB has a magnetic tripping value of the fuse. Therefore, MCBs with different
characteristic between 5 and 10 times the rated current. characteristics and rated breaking capacities also have
This magnetic tripping characteristic would therefore different selectivity limits. The subsequent tables show the
become between 7 and 14 times the rated current. currents up to which selectivity is provided between MCBs
and upstream fuses according to DIN VDE 0636 Part 21. The
Frequency Variation values specified in kA are limit values which have been
determined under unfavourable test conditions. In practice,
MCBs may be used up to their normal voltage rating on better values can be obtained, depending on the type of the
400Hz supplies; however the magnetic tripping upstream fuse.
characteristic must be increased by 30% (e.g. Type ‘C’ MCB
with magnetic characteristics between 5 and 10 times the In the event of a short circuit, when using the 5SX4, MCBs
rated current would become between 6.5 and 13 times and fuses according to DIN VDE 0636 Part 21, Selectivity is
rated current. provided up to the indicated values in kA.
The main use of D characteristics MCBs is to ensure correct • Current limiting class 3 MCBs
sizing of the device wherein high inrush currents are • Finger touch proof terminals (FTPT)
prevailing.
• Trip free mechanism
This characteristics allows to use in a high in rush current
circuits without requiring the MCB to be over sized. • Suitable for AC/DC circuits
D characteristics MCB shall take the in rush current with • DIN rail and screw mounting possible
peak up to 10 times In, (Rated current) and can be used • Accessories like auxiliary contact, shunt trip,
best advantage for handling much higher in rush circuits undervoltage release, fault signal contact
eg: Switching solenoids/capacitor banks/transformers etc.
Applications
Under D characteristics, the magnetic operating limits (for
short circuit operations) are between 10 to 20 times the • Mainly as an incomer MCB in residential, industrial and
rated current of MCB. commercial applications
For example the instantaneous mechanism of 10A MCB will • C characteristics MCBs suitable for general line
operate between 100A and 200A in an over current protection especially with higher starting current lamps,
situation. motors etc.
• D characteristics MCBs suitable for high inrush current
Selectivity of miniature circuit-breakers/fuses
applications line transformers generating significant
Generally, distribution networks are configured as radial pulses, solenoid valves etc.
1/6
1/4
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Overview
Features
• Compact in size and hence reduction in panel size.
• Total recessed dial avoids accidental switching due to
human negligence.
• Suitable for breaking capacity up to 10 kA
• Accessories like Aux block, fault signal contacts can be
retro fitted at site.
• Finger touch proof (FTPT) ensures total safety for
operator.
1/7
1/5
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Technical data
1/8
1/6
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Technical data
Tripping characteristics
1/9
1/7
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Technical data
1/10
1/8
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
1/11
1/9
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Note:
Stock Items
# 1MW (Module Width) = 18mm
1/12
1/10
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Betagard Miniature Circuit Breakers, LS125 - 5SP4, 10kA MCBs with C/D characteristics
Un: 240/415V, 50…60Hz can be used in systems upto 60Vdc, 1P and 110Vdc, 2P
Standards: IS 60898, IEC 60898
Breaking capacity: 10kA as per IS 60898; Icu=20kA as per IS 60947-2
With ISI marking : CM/L No. 2255548
C characteristic
Rated current MW# Reference No. Std. Pkg.
In (A) (Nos.)
4-pole 80 6 5SP44807RC 1
100 5SP44917RC 1
125 5SP44927RC 1
D characteristic
4-pole 80 6 5SP44808RC 1
100 5SP44918RC 1
Note:
Stock Items
# 1MW (Module Width) = 18mm
1/13
1/11
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Note:
# 1MW (Module Width) = 18mm
1/14
1/12
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Additional components
For applications in industry and in system and plant section of 2.5 mm² and are delivered with combined
engineering, add-on accessories are available, such as slotted and podzidrive head screws.
auxiliary contacts (AC), fault-signal contacts (FC), shunt
trips (ST). ST is mounted left of MCB. AC/FC are mounted Fault signal contacts (FC)
on right side. These modules can be used as inputs/outputs The fault signal contact block has a structure and
to a PLC, building-automation system etc. for signalling and dimensions identical to those of the auxiliary contact block
control. (AC). The fault signal contact block remotely indicates the
tripping of device due to an overload or a short-circuit. The
Auxiliary contacts (AC) block’s contact remain in position when the circuit-
Each block consists of two electrically independent breaker’s handle is manually actuated.
contacts (separated electrical circuits); one of these
contacts is normally open and the other normally closed. Shunt trip (ST)
The mechanically stable position of the contacts does not The shunt trip coil allows the circuit breaker to be remotely
change unless the circuit-breaker is manually actuated or is tripped. The coil and circuit breaker are coupled together
tripped due to an overload or a short circuit. The terminals not only by using the control handle, but also with the
are characterised by a degree of protection IP 2X; they internal trigger.
allow connecting conductors with a maximum cross-
1/15
1/13
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Additional components
Benefits Application
• Can be retrofitted individually Indication of the miniature circuit-breaker’s switching state:
(for mounting concept, refer to page 2/7)
– AS: ON/OFF
• Can be connected to instabus KNX EIB and AS-Interface
– FC: tripped
bus over binary inputs
Design
• Min contact load: 50 mA, 24 V
#
1 Module Width (MW) = 18mm
1/16
1/14
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Additional components
Benefits
• 5SJ, 5SY, 5SL, 5SP and 5TE8 series of MCBs/ Isolators can • The ROH can be padlocked in OFF position with the help
be fitted with Betagard Rotary Handle Assembly (ROH) of suitable padlocks thereby ensuring complete safety to
for installation in Switchgear Cubicles and Distribution operating personal during maintenance.
Panels • Door interlock and defeat facility is available as a
• The ROH gives operating uniformity and improves the standard feature.
aesthetics of the panel.
Applications
• Panel Boards / Switch Boards
Technical Details:
Product Order No Weight PS*/ P
1 item Kg unit Items
Rotary Handle Assembly for MCB 5ST38140RC 0.584 1
1/17
1/15
Betagard Miniature Circuit Breakers &
Betagard DC Circuit Breakers
Dimensions
SP DP TP FP
1MW = 18mm
SP DP TP FP
1MW = 18mm
SP DP TP FP
MW = 1 MW = 2 MW = 3 MW = 4
1MW = 18mm
All dimensions in mm
1/18
1/16
Betagard Residual Current Breaker
Operator
2/2 Overview
2
2/3 Technical specifications
2/8 Dimensions
1/19
2/1
Betagard Residual Current Breaker Operator
Overview
The resistance of a human body to current depends on the the demand is for automatic interruption of the power
current path. Measurements have shown that, a current supply when a fault can pose a risk due to the intensity
path of hand/hand or hand/foot has a resistance of approx. and duration of the touch voltage.
1000Ω, taking into account a fault voltage of 230V AC, this
produces a current of 230mA for the current path hand/ 3. Fire protection – For locations exposed to fire hazards,
hand. residual current protective devices should offer earth
leakage protection for the prevention of fires, which
Three function groups largely determine the setup of may originate from insulation faults.
residual current protective devices:
Types of residual current protective devices
a. Summation current transformers for fault current
detection 1. Type AC – Residual current protective devices of type AC
are suitable only for detecting sinusoidal AC residual
b. Releases to convert the electrical measured quantities
currents.
into a mechanical tripping operation
2. Type A – In addition to AC sinusoidal currents, residual
c. Breaker mechanism with contacts
current protective devices of type A also measure
The summation current transformer covers all conductors pulsating DC residual currents. e.g. applications like
required to conduct the current, i.e. also the neutral ECGs, washing machines, fax machines etc. having
conductor where applicable. electronic components.
In a fault free system, the magnetizing effects of the Betagard RCBOs have the unique distinction of combining
conductors through which current is flowing cancel each the earth leakage protection function of an RCCB with the
other out for the summation current transformer, as the overload and short circuit function of MCB.
sum of all currents is zero. There is no residual magnetic
Betagard RCBO (2P, 2M) is available from 6 to 40A in
field left that could induce a voltage in the secondary
1Pole+Neutral version. The device has a breaking capacity
winding. However, by contrast, if a residual current is
of 10kA as per IEC60898 and is available in 2 Module width
flowing due to an isolation fault, this destroys the
size.
equilibrium and a residual magnetic field is left in the core
of the converter. This generates a voltage in the secondary This RCBO can be used for personnel as well as fire
winding, which then uses the release and the breaker protection:
mechanism to switch off the electrical circuit afflicted with
the isolation fault. This tripping principle operates – IΔn ≤ 30mA: Additional protection in the case of direct
independently of the system voltage or an auxiliary power contact
supply. This way it can be ensured that the full protective
action of the residual current protective device is – IΔn ≤ 300mA: Preventive fire protection in the case of
maintained even in the event of a system fault. ground fault currents
Due to the use of electronic components in household Betagard RCBOs are also offered combination devices,
appliances and industrial plants, insulation faults can also which offer overcurrent protection for overload and short
cause residual currents that are not AC residual currents to circuit protection in addition to protection against residual
flow through residual current protective devices, even in currents. A version in this device group is a residual current
the case of devices with ground terminals. block (RC unit) combined to a miniature circuit breaker
(selected on the basis of characteristic & rated current) to
The basic prerequisite for use of a residual current form a RCBO. These devices are factory assembled and
protective device is the running of a grounded PE offer the same functions as RCBO. The RC unit has no
conductor to the components and equipment to be contacts of its own; in the event of a fault, it trips the
protected. A current flow can then pass through a human circuit breaker, which opens the contacts and interrupts the
body only when two faults occur (1) Interruption of the PE circuit.
conductor in addition to the insulation fault or (2) When
there is unintentional contact with live parts. Betagard RCBOs are available in 4 standard versions from
32A to 63A. They offer 10kA-breaking capacity as per
Residual current protective devices offer protection against IS8828 in 2P and 4P versions.
1. Direct contact – Direct contact is considered as direct 1. MCB C characteristics with RC unit Type AC
contact of a human body with a live part.
2. MCB C characteristics with RC unit Type A
2. Indirect contact (fault protection) – Indirect contact is
considered as the contact of a human body with a de- 3. MCB D characteristics with RC unit Type AC
energized, electrically conductive part. In these cases, 4. MCB D characteristics with RC unit Type A
1/20
2/2
Betagard Residual Current Breaker Operator
Technical specifications
Standards IS 12640-2 (2008), IEC 61009, VDE 0664 Part 20/Part 30, IEC 61543
Poles 1Pole + N, 2P, 4P
Rated voltages, Un (V) 125…240V AC, 50…60Hz; 240V / 415 V AC 50...60Hz
Rated currents, In (A) 6, 10, 16, 20, 25, 32, 40, 63
Rated residual currents (mA) 30, 100, 300
Rated short circuit capacity (kA) 10
Tripping characteristics C, D
Energy limiting class 3
Enclosure Gray molded plastic (RAL 7035)
Mounting depth (mm) 70
Terminals
1. Conductor cross section (sqmm) 1… 25
2. Terminal tightening torque (Nm) 2.5…. 3
Supply connection Either top or bottom
Mounting position Any
Mounting technique Can be snapped on to a 35mm DIN rail
Degree of protection IP20 acc to EN60529 (VDE 0470 Part 1)
IP40/IP42 for installation in distribution boards
Minimum operating voltage for test function operation (V) 195V AC
Device service life > 10,000 operations (electrical and mechanical)
Storage temperature (°C) -40…. +75
Ambient temperature (°C) -25…. +45
CFC and silicon free Yes
1/21
2/3
Betagard Residual Current Breaker Operator
Product overview
1/22
2/4
Betagard Residual Current Breaker Operator
Product overview
1/23
2/5
Betagard Residual Current Breaker Operator
Additional components
Benefits Application
• Can be retrofitted individually Indication of the miniature circuit-breaker’s switching state:
(for mounting concept, refer to page 2/7)
– AS: ON/OFF
• Can be connected to instabus KNX EIB and AS-Interface
– FC: tripped
bus over binary inputs
Design
• Min contact load: 50 mA, 24 V
1/24
2/6
Betagard Residual Current Breaker Operator
Additional components
Mounting concept
Using this mounting concept, all additional 5ST3
components can be combined with residual current breaker
operators of 5SU1 series:
1/25
2/7
Betagard Residual Current Breaker Operator
Dimensions
2P-2M
2P-4M 4P-7M
Add-on components
All dimensions in mm
1/26
2/8
Betagard Distributions Boards
3/2
3
Design, construction and
features
Simply stylish
3/4 Selection and ordering data
3/7 Dimensions
1/27
3/1
Betagard Distributions Boards
Siemens Betagard distribution boards are suitable as sub- These distribution boards are provided with removable top
distribution boards in all domestic, commercial and and bottom gland plates with adequate number of knock
industrial applications. outs, enabling easy installation and connection of conduits
of all sizes for top and bottom entry of cables.
Owing to their small overall depth, they are used in both
residential and commercial buildings and are usually Double door construction of DBs facilitates easy removal of
installed in the vicinity of respective load centers. inspection window mounted on intermediate plate.
They are connected down stream of the meter cabinet and A 15 deg correction factor is possible if the U plate of
the main or storey distribution board. distribution boards is wrongly installed.
Design: Due to the above fact it is obvious that they must offer
Siemens Betagard distribution boards in sheet steel have • Maximum safety by means of fire and corrosion
been specially designed, keeping in view the interiors of resistance.
modern day houses and commercial establishments.
• Mechanical strength and increased shock hazard
Installation: protection.
Betagard distribution boards are available both in flush as Safety requirements, for which our SIMBOX LC have
well as surface mounting versions. consistently been tested and independently certified in
compliance with EN 60439-3; IEC 60439-3
1/28
3/2
Betagard Distributions Boards
6 SIMBOX WP
Due to high degree of protection IP65, these small
distribution boards can withstand harsh ambient
5 conditions in both indoor and outdoor areas.
Their resistance to dust and splashing water makes them
4
ideal for use in a range of different application areas, such
1 as car washes, farms, joiners’ workshops, etc.
3
2 Due to their large temperature operating range (-25°C to
+60°C) UV radiation resistance and resistance to dust and
1 Transparent and removable DB door 4 Provision for cylindrical security lock
splashing water, this distribution board range is especially
2 Intermittent windows 5 DIN Rail arrangements suitable for harsh ambient conditions.
3 Removable Intermittent Plate (IP) 6 Neutral link / Earthing termination
Design
Features:
Equipment
• A red-hot case for fire protection The distribution boards can be equipped with modular
In order to avoid fire damage caused by short circuits, installation devices, such as MCBs and RCCBs with 63 A and
we check our SIMBOX LC for their fire-resistant a mounting depth of 55 mm up to 70 mm, by snapping
properties in the 'glow-wire test' onto the standard mounting rails 35 mm x 7.5 mm to
EN 60715.
• Taking all the knocks
Depending on the selection, the small distribution boards
Mechanical strength is a further criterion to which we
can be equipped with devices of 12 to 18 modular widths.
pay utmost attention. We therefore test our SIMBOX LC
DBs for the danger of an electric shock following an
Technical specifications
impact load.
• Spotless reputation Rated current in A Up to 63
As soon as live parts start to rust, safe operation can not Rated voltage in V AC 400
be guaranteed. Therefore we also test the SIMBOX LC Degree of protection IP65
DBs for its resistance to corrosion. To do this, the test Safety class 2 (total insulation)
item is immersed in a solution of ammonium chloride,
then stored for a specified period in a warm, damp Color Light gray RAL 7035
atmosphere. The test is only passed if no traces of rust
appear. Standards
• We do not like the shocks and we believe in easy The SIMBOX WP small distribution boards comply with
handling EN 60439-3 and IEC 60439-3.
The SIMBOX LC conforms to IP 40 degree of protection.
This means that reliable level of shock hazard protection Versions
is guaranteed. Tiers MW per tier
The unique design of Intermittent window cover 4 8 12 18
enables electrician for easy access to components and 1 9 9 9 9
wires without opening the IP cover and door while
installation and maintenance. 2 – – 9 9
3 – – – 9
Bring home installation benefits: 4 – – – 9
• The SIMBOX LC is designed by the top Italian designer
Giorgio Giugiaro, who is one of the most celebrated Benefits
designers of consumer and industrial products. • The wiring space behind the standard mounting rail is
• The rail spacing of 150mm offers plenty of room for 15 mm and 48 mm, ensuring fast and easy wiring.
quick and easy wiring of the built in devices. • The extremely robust transparent door can also be
• The screw terminal offers sufficient clamping points for equipped with a lock, which can be ordered from the
range of accessories. The door can be hinged on the
N and PE conductors.
right or left without tools; its opening angle is 180°.
• The DBs can subsequently be fitted with a lock.
• The withdrawable equipment rack ensures easy and fast
• Facility available to hinge the door on the left or right assembly. The generous wiring space and clearly
hand side. arranged modular design reduce assembly times by
• The set of labels and symbols supplied permits tidy approx. 20%.
labeling of the respective circuits. • The plastic materials used can be recycled.
1/29
3/3
Betagard Distributions Boards
Note:
Stock Items
# 1MW (Module Width) = 18mm
For insulated shorting links for Betagard Distribution Boards, please refer page 8.
1/30
3/4
Betagard Distributions Boards
3VT1 MCCB with thermal magnetic trip unit (overload and short circuit protection)
Breaking capacity, Icu = 25kA at 415V AC, 50Hz.
Standards: IS 13947-2 / IEC 60947-2
"with CE marking"
Note:
Stock Items # 1MW (Module Width) = 18mm
1/31
3/5
Betagard Distributions Boards
Note:
Stock Items
# 1MW (Module Width) = 18mm
1/32
3/6
Betagard Distributions Boards
Dimensions
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
Configuration
Type ref No of slots/row No of rows Total
8GB31424RC 12 2 24
8GB31426RC 16 2 32
Dimension (mm)
Knockout
Per side (top & bottom) Per side flap
Model A B C
combination
Combi Combi Ø32/Ø21
Ø40/Ø28 Ø32/Ø20 combi
12 x 2 Rows 345 194 318 2 3 2
16 x 2 Rows 433 282 406 2 5 2
Application: recommended for residential and commercial buildings where-in mounting of modular devices like
timers, ammeters, and TP MCBs are to be connected in the outgoing circuits.
1/33
3/7
Betagard Distributions Boards
Dimensions
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
Configuration
Type ref No of slots/row No of rows Total
8GB3144 2RC 8 4 32
8GB3144 4RC 12 4 48
8GB3144 6RC 16 4 64
Dimension (mm)
Knockout
Per side (top & bottom) Per side
Model A B C
flap
Combi Combi Ø32/Ø21
Ø40/Ø28 Ø32/Ø20 combi
8 x 4 Rows 273 124 246 2 1 3
12 x 4 Rows 345 196 318 2 3 3
16 x 4 Rows 433 284 406 2 5 3
Application: highly recommended for commercial buildings where-in the total number of circuits are considerably
more. Beta flex can offer 16 module X 4 rows design DB which can accommodate 64 modules in total of 55/70mm
depth.
1/34
3/8
Betagard Distributions Boards
Dimensions
Betagard SPN DB (8GB31) with or without TV splitter and krone type telephone socket
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
Configuration
Type ref No of slots/row No of rows Total
8GB31215RC 14 1 14
8GB31315RC 14 1 14
Dimension (mm)
Knockout
Total (top & bottom) Per side flap
Model A B C
size Ø32 & Ø21
Ø32 Ø26 combination
8GB31215RC 383 254 356 2 11 2
8GB31315RC 383 254 356 2 11 2
Application: Recommended for single phase power distribution network + TV & telephone connection in one
location in order to give better aesthetics and neat wiring.
1/35
3/9
Betagard Distributions Boards
Dimensions
Betagard TPN DB (8GB31) with or without TV splitter and krone type telephone socket
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
Configuration
Type ref No of slots/row I/C Slots O/G Slot Total
8GB31221RC 6 8 3X 6 26
8GB31321RC 6 8 3X6 26
Dimension (mm)
Knockout
Per side (top & bottom) Per side flap
Model A B C
size Ø32 & Ø21
Ø32 Ø26 combination
8GB31221RC 510 380 484 2 8 2
8GB31321RC 510 380 484 2 8 2
Application: Recommended for three phase power distribution network + TV & telephone connection in one
location in order to give better aesthetics and neat wiring.
1/36
3/10
Betagard Distributions Boards
Dimensions
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
Configuration
Type ref No of ways I/C slots (MCB+RCCB) O/G slots TP/SP (V.Bus Bar)
8GB3147 1RC 4 12 4/12
8GB3147 3RC 6 12 6/18
8GB3147 4RC 8 12 8/24
8GB3147 7RC 12 12 12/36
Dimension (mm)
Knockout
Model A B C Top & bottom Per side flap Per side flap
combination Bottom slit combination combination
Ø42 & Ø35 Ø32 & Ø20 Ø40 & Ø28
4 Way 477 347 450 4 72 X 46 2 1
6 Way 531 401 504 4 72 X 46 3 1
8 Way 585 455 558 4 72 X 46 4 1
12 Way 693 563 666 4 72 X 46 6 1
Application: Recommended where ever TP/SP MCBS are to be mounted in the outgoing circuits. The ready made
insulated vertical bus bar will simplify the wiring job apart from giving total safety.
1/37
3/11
Betagard Distributions Boards
Dimensions
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
Configuration
I/C slots O/G slots TP/SP
Type ref No of ways
(MCB+RCCB) (V.Bus Bar)
8GB3157 1RC 4 12 4/12
8GB3157 2RC 6 12 6/18
8GB3157 3RC 8 12 8/24
8GB3157 4RC 12 12 12/36
Dimension (mm)
Knockout
Model A B C Top & bottom Per side flap Per side flap
combination Bottom slit combination Ø32/Ø20 combination Ø40/Ø28
Ø40/Ø28
(with gland plate)
4 Way 530 400 503 4/2 72 X 46 2 1
6 Way 584 454 557 4/2 72 X 46 3 1
8 Way 638 508 611 4/2 72 X 46 4 1
12 Way 746 616 719 4/2 72 X 46 6 1
Application: highly Recommended where ever MCCB as incomer up to 160A and TP/SP MCBS are to be mounted in the
outgoing circuits. The ready made insulated vertical bus bar will simplify the wiring job apart from giving total safety.
3/12
1/38
Betagard Distributions Boards
Dimensions
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
Configuration (without 3 Nos. 40A change over switch & LED indication)
Type ref No of ways (MCB + RCCB) I/C slots O/G slot Total
8GB3184 0RC 4 8 3X4 20
8GB3184 1RC 6 8 3X6 26
8GB3184 2RC 8 8 3X8 32
8GB3184 4RC 12 8 3 X 12 44
MLFB Type A B C
8GB3184 0RC 4 way 442 313 415
8GB3184 1RC 6 way 477 348 450
8GB3184 2RC 8 way 512 383 485
8GB3184 4RC 12 way 587 458 560
Application: recommended where ever the reliability of 3 phase supplies are not dependable. Beta change over DB will
have a feature to shift the load connected to the dead phase to a live one whenever there is a failure of any one phase.
3/13
1/39
Betagard Distributions Boards
Dimensions
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
Note:
1) Powder coating 100±25μ
2) Colour ivory while RAL-9016 shade
3) All dimensions are in mm.
3/14
1/40
Betagard Distributions Boards
Dimensions
Simbox LC
Simbox WP
1-tier 8GB1 371-0, 8GB1 371-1, 8GB1 371-2, 8GB1 371-3 2-tier 8GB1 372-2, 8GB 372-3 (3- and 4-tier versions not shown)
MW Type Dimensions
a b c dmax e f g h i k l m n o
1x4 8GB1 371-0 210 148 100 75 48 15 105 105 – – – – 156 87
1x8 8GB1 371-1 210 215 100 75 48 15 105 105 – – – – 110 87
1 x 12 8GB1 371-2 260 298 140 75 48 48 117.5 142.5 – 102 75 21 161 200
1 x 18 8GB1 371-3 285 410 140 75 48 48 117.5 142.5 – 102 75 21 185 310
2 x 12 8GB1 372-2 420 298 140 75 48 48 147.5 122.5 150 102 75 21 320 200
2 x 18 8GB1 372-3 463 410 140 75 48 48 155.5 131.5 150 102 75 21 210 293
3 x 18 8GB1 373-3 655 410 140 75 48 48 162.5 142.5 175 102 75 21 363 319
4 x 18 8GB1 374-3 878 410 160 75 48 48 175 155.5 175 102 75 21 394 319
3/15
1/41
Betagard Distributions Boards
Wiring instructions
Three Phase Incoming & TP/SP outgoing with vertical busbar system
Beta Bus: 125A 5SP4, 63A 5SX4, 5SJ4 and 5SQ2 as an incomer and SP/TP MCB upto 63A 5SX4 as an outgoing
Beta Bus Plus: 160A 3VT1 MCCB as an incomer and SP/TP MCB upto 63A 5SX4 as an outgoing
1/42
3/16
Automatic Transfer Switching
Equipment - ATSE
4/2 Overview
4
Power... When it matters the most! 4/3 Selection & ordering
4/7 Schematics
1/43
4/1
Automatic Transfer Switching Equipment - ATSE
Overview
Background:
Back up power source has become an integral part of automatic and safe changeover of power supply. It
almost every commercial, residential & industrial conforms to latest standard IS/IEC 60947-6.
installation. Many of the residential or commercial project
In event of power failure or under voltage condition Betagard
developers provide to their occupants availability of
5TR ATSE automatically shifts the load from normal power
continuous power especially for critical applications such as
supply to back up power supply. This changeover is
lifts, lobby lighting, operation of water pumps etc. To
initiated once backup power source is available at incoming
provide power at all times for above applications a backup
of backup MCB.
power source is used. It could be DG or from other utility as
a stand by power source. Once normal power supply restores, it waits for a user
defined delay time and than it shifts back from backup
This would typically necessitate use of switching and
power supply to normal power supply.
changeover devices. Betagard 5TR ATSE is a solution for the
above applications for DG sets upto 82.5kVA or a power Betagard 5TR ATSE is available in two versions i.e. Basic &
source from which load can draw maximum 125A. Advance. One of the key visible differences in Advance
version is a LED display on the controller for settings apart
Betagard ATSE has two separate MCBs one for Normal
from some more features and operational differences.
power and the other for backup power. Electronic
controller mechanically operates these MCBs and performs
1/44
4/2
Automatic Transfer Switching Equipment - ATSE
Benefits: Applications:
• Prewired solution provides ease in installation • Common Area Lighting in residential Complexes and
commercial Installations.
• Prewired and ready to install product. (Controller + 2 no
of MCBs upto 125A) • Lift Back up Supply in the event of power failure in
Residential Apartments and Societies.
• Simple Switching device which also protects.
• Small Commercial Establishments e.g. Shopping
• Available for single phase and three phase applications.
Complex etc
• Front panel LED indications as well as contacts for
• Data Centre and Server room back up.
external indications.
• Change over for Back up supply for individual
• Protection against under voltage (Fixed at 70% Un in
Residences in Apartments and Bungalows.
Basic Type & Adjustable from 70-85% Un in Advance
type) and phase failure.
• Mechanical Interlock using two position lever.
• Shrouded outgoing terminals
• Automatic as well as manual operation.
• Adjustable transfer time from 1.5secs to 60secs
• MCB Trip / Contact weld indication with Alarm function.
• Emergency shut down signal input (From fire system or
some other external source in Advance type)
4-Pole 40 5TR13348RC40 1
63 5TR13348RC63 1
100 5TR13347RC81 1
125 5TR13347RC82 1
4-Pole 40 5TR23348RC40 1
63 5TR23348RC63 1
100 5TR23347RC81 1
125 5TR23347RC82 1
1/45
4/3
Automatic Transfer Switching Equipment - ATSE
Technical specifications
Technical Specifications
5TR1 5TR2
Standards IS/IEC 60947-6
Rated Control Supply voltage Vac AC240V
(Sourced from Power & backup supply MCB incoming terminals)
Rated operational Voltage Ue 240/415 Vac
Rated Frequency Hz 50
Rated Current A 40, 63, 80, 125A*
Utilisation Category AC 33B#
Rated breaking capacity according to 60898-1 (Icn) KA 10KA
Rated breaking capacity according to 60947-2 (Icu) KA 15KA for 40 & 63A, 20KA for 100 & 125A
Controller
Transfer delay Adjustment Analog (Using Pot) Digital (Switch)
Minimum transfer Time Sec 1.5~2.5s
Operating transfer time Sec instantaneous~60s
Return Transfer Time Sec instantaneous~60s
Under voltage setting % 70~Ue (fixed) 70~85~Ue (settable)
MCB Trip / Contact Weld alarm indication Yes
External Indication Contacts AC240V, <40W
Remote controlled Emergency Shut Down (24V DC) No Yes
Outgoing Terminals
Connection type Nut-Bolt terminal for ring / fork type lug
Conductor Cross Section Sq mm 16-50 Sqmm for 40 & 63A, 16-95 Sqmm for 100& 125A
Terminal Tightening torque Nm 3 Nm for 40 & 63A, 10 Nm for 100& 125A
Stripping length / Bolt Size 18 mm / M6 for 40 & 63A, 18mm / M8 for 100& 125A
Functions
Auto Transfer on Phase failure / Undervoltage Yes
Auto throw Auto return 1
Yes
Auto throw without auto return2 Yes
Manual Operation using Push Button No Yes
Manual operation using external handle Yes
Third state3 Yes
Net –Net mode4 Yes
Net-generator mode 5
No Yes
#
AC 33B - Motor Loads or Mixed loads including motors, resistive loads and up to 30% Incandescent lamp Loads
1
In case of normal power supply failure, ATSE will transfer from normal supply to backup supply automatically and once the normal power supply recovers, ATSE
returns automatically from backup power supply to normal power supply.
2
In case of normal power supply failure, ATSE will transfer from normal supply to backup supply automatically and once the normal power supply recovers, ATSE does
not return from backup power supply to normal power supply.
3
Both MCBs in OFF position (Total Shut Down)
4
In this mode backup is considered to be available all the time. No signal from will be generated at ATSE for Generator as start command on failure of normal power
supply.
5
In this mode backup power is a generator power supply and a signal output is generated from ATSE which is used for generator as start command.
* 40A & 63A MCBs are of D Characteristics and 100 & 125A MCBs are of C characteristics
1/46
4/4
Automatic Transfer Switching Equipment - ATSE
ATSE type
1/47
4/5
Automatic Transfer Switching Equipment - ATSE
Dimensional details
Figure 2: Dimensions (5TR1& 5TR2 with rated current 100A & 125A)
1/48
4/6
Automatic Transfer Switching Equipment - ATSE
Schematics
Wiring
Figure 3: ATSE main system with neutral line Figure 4: ATSE main system without neutral line
Indication:
In 5TR series, 240V AC output voltage is used for indication Generator set start Signal: 5TR2 ATSE has potential free
- Terminal 1 & 2, 240V AC output point for indication of output point for starting the generator set. This contact is
availability of Back up supply (supplied from Back up Normally Closed when normal power is available and
power) change to Normally Open on mains failure. Works only in
net-generator mode
- Terminal 3 & 4, 240V AC output point, for indication of
the load is on Backup supply (supplied from normal power) Fire Alarm input: 5TR2 ATSE has fire control signal terminal.
In case of emergency, 24V DC input between terminal 10
- Terminal 3 & 5, 240V AC output point for indication of
& 9 will transfer ATSE to third state i.e. complete shutdown
the load is on Normal supply (supplied from normal power)
of normal and backup power.
- Terminal 3 & 6, 240V AC output point for indication of
availability of normal supply (supplied from normal power)
1/49
4/7
Automatic Transfer Switching Equipment - ATSE
3WT – ACBs
3VT – MCCBs
5TR – ATSE
5SX / 5SJ – MCBs
3TF – CONTACTORS
3UA – Bi RELAY
M – MOTOR OR LOAD
4/8
Notes
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Your partners
Sales offices:
Ahmedabad Chennai Kolkata Nagpur
3rd Floor, Prerna Arbur Sathak Centre, No.4., Mahatma Gandhi Road 43, Shanti Palli, Rashbihari Bypass Connector 5th Floor, Land Mark Building
Girish Cold Drinks Cross Roads, Off G.C.Road Chennai - 600034 Eastern Metropolitan Bypass Wardha Road, Ramdas Peth
Ahmedabad - 380 009 : +91 44 28334000 Kolkata - 700 042 Nagpur - 440 010
: +91 79 40207600 Fax: +91 44 28334088 : +91 33 2444 9000, 24428641-47 : +91 712 6633000
Fax: +91 79 40207699 Fax: +91 33 2444 9010/13 Fax: +91 712 6633111
Coimbatore
Bengaluru 7th Floor, Global Towers, 1057, Avinash Road Lucknow New Delhi
1st Floor, Jyoti Mahal, No. 49, St. Marks Road Coimbatore - 641 018 28/45, Ashok Marg, Opp. Indira Bhawan 4A, Ring Road, I.P.Estate, Box.No.7036
Bengaluru - 560 001 : +91 422 4336300 Lucknow - 226001 New Delhi - 110 002
: +91 80 22042000 Fax: +91 422 4336310 : +91 522 4031022, 4031000 : +91 11 2345 5000-09
Fax: +91 80 22224131 Fax: +91 522 4031019 Fax: +91 11 42995030
Hyderabad
Chandigarh 5-9-19, 4th & 5th Floor, Laxmi Narasinh Estate Mumbai Pune
SCO 188/191, 3rd Floor, Sector-17 C Opp. Secretariat Road, Saifabad 8th Floor, R&D Technology Centre Tower B/701-705, ICC Trade Tower
Chandigarh - 160 017 Hyderabad - 500 004 Thane Belapur Road, Airoli Node 403A, Senapati Bapat Road
: +91 172 4690300 : +91 40 2348 2500 Navi Mumbai - 400 708 Pune - 411016
Fax: +91 172 4690399 Fax: +91 40 23243145 : +91 22 2764 5005-6 : +91 20 2570 6000
Fax: +91 22 27645867 Fax: +91 20 2570 6060
Territory managers:
Aurangabad Indore Nasik Trichy
A9, Yogeshwari Vrundavan, Nr. Malhar Chowk Flat No. 102, Panchavati Apart. “Aditya Avenue”, Flat No.27, 4th Floor Door No.106, Grd. Flr., 5th Cross Street
Garkheda Parisar, Prem Nagar 40 Chandralok Colony, Khajrana Road B-Wing, Near Chandak Circle, Tidke Colony Vidyasalai Road, Ganapthy Nagar, Thiruvanai Koil
Aurangabad - 431210, Maharashtra Indore - 452001, Madhya Pradesh Nasik - 422001, Maharashtra Trichy - 5
Mobile: +91 9766316446 Mobile: +91 9926939993 Mobile: +91 9822193204 : +91 431 4345621
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected] Mobile: +91 9840843121
E-mail: [email protected]
Belgaum Jaipur Nasik
H.No.713, Narvekar Lane, Shahpur 6, Park Street, Opp. Pink City Petrol Pump, M.I.Road A-12, Eshwar Park, Behind Nasik Cambridge School Trivandrum
Belgaum - 590003, Karnataka Jaipur - 302006, Rajasthan Opp. Church, Indira Nagar Udayakiran, T.C.No.28/535
: +91 831 2495156 : +91 141 2370274, 2377956 Nasik - 422009 Krishnakovil Road, Kaithamukku
Mobile: +91 9740277991 E-mail: [email protected] Mobile: +91 9823477735 Trivandrum - 695024, Kerala
E-mail: [email protected] E-mail: [email protected] Mobile: +91 9895979604
Jaipur E-mail: [email protected]
Bhilai Pondicherry
6, Park Street, Opp. Pink City Petrol Pump, M.I.Road
25/2, Nehru Nagar (West), SBI Colony SELVAN ILLAM, 2nd Floor, No. 1 Udaipur
Jaipur - 302006, Rajasthan
Bhilai - 490020, Chhattisgarh Villianoor Road, Nadesan Nagar 303, Oasis Park, PP Singhal Marg, Ambavgarh
: +91 141 5152108
Mobile: +91 7869913404 Pondicherry - 605005 Udaipur - 313001, Rajasthan
Mobile: +91 9829244313
E-mail: Yet to create Mobile: +91 9840143536 : +91 294 2430345
E-mail: [email protected]
E-mail: [email protected] Mobile: +91 9829039120
Bhopal Jalandar E-mail: [email protected]
Flat No-104, Sagar Home Phase-2 Raipur
H.No.943, Urban Estate, Phase I
Sarvadharma Society, Nayapura Road Flat.No.103, First Floor, Block-B, Shilp Enclave Rudrapur
Jalandar - 144022, Punjab
Bhopal - 462042 Nr.LAS Colony, Shankar Nagar 13/14, Model Colony, Nr.Gopinath Mandir
: +91 181 4613929
Mobile: +91 9977228084 Raipur - 492007, Chhattisgarh Station Road, Distt.Udhamsingh Nagar
Mobile: +91 9876047929
E-mail: [email protected] Mobile: +91 9425057945 Rudrapur - 263153, Uttarkhand
E-mail: [email protected]
E-mail: [email protected] Mobile: +91 9839813707
Bhuwaneshwar Jamshedpur E-mail: [email protected]
Flat No. 109, Hara Priya Apartment, Vivekanand Marg Rajkot
823, Udaigiri Vijaya Heritage, Uliyan, Kadma
Bhuwaneshwar - 751002, Orissa “Vrujraj”, Chandanpark Society Vadodara
Jamshedpur - 831005, Jharkhand
: +91 674 2430734 Opp. Gyanganga Vidhyapith, Nr. Raiya Circle 3rd Floor, Ohm Business Park
: +91 657 6451637
Mobile: +91 9937009749 Rajkot - 360005, Gujarat Opp. Balaji Hospital, Ellora Park, Subhanpura
Mobile: +91 9934311352
E-mail: [email protected] Mobile: +91 9825021026 Vadodara - 390023
E-mail: [email protected]
Mobile: +91 9937097504 E-mail: [email protected] : +91 265 6692121
E-mail: [email protected] Jodhpur Mobile: +91 9825506962
Mobile: +91 9583061766 Ranchi Email: [email protected]
371, Gauri House, Kamala Nehru Nagar, Nr. SBI Bank
E-mail: [email protected] H-1/187, Harmu Housing Colony, Harmu Mobile: +91 9825069175
Jodhpur - 342008, Rajasthan
Ranchi - 834002, Jharkhand Email: [email protected]
: +91 291 2760371
Cochin Mobile: +91 9234610953
Mobile: +91 9828327200
K.G.Oxford Business Centre E-mail: [email protected] Vapi
E-mail: [email protected]
3A, Shreekandath Rd, Ravipuram Flat No.302, Samrajya IV, Royal Residency
Cochin - 682016 Kanpur Renukoot Gokul Vihar Township, Charwada Road
: 91 4028611/22 Above ICICI Prudential Office Vapi - 396195, Gujarat
106, Agarwal Apart.
Mobile: +91 9387384848 Patel Nagar, Murdhawa, Dist. Sonebhadra : +91 260 6451156
Nr. Hari Har Dham Mandir, Shyam Nagar
E-mail: [email protected] Renukoot - 231217, Uttar Pradesh Mobile: +91 9825147957
Kanpur - 208013, Uttar Pradesh
Mobile: +91 9744511109 : +91 544 254693 E-mail: [email protected]
: +91 512 2423348
E-mail: [email protected] Mobile: +91 9838007897
Mobile: +91 9839102434
Mobile: +91 9895052944 E-mail: [email protected] Vapi
E-mail: [email protected]
E-mail: [email protected] Flat No.203, Plot No.55
Kolhapur Rourkela Kadri Manzil, Godal Nagar, Distt. Valsar
Durg T-15, Civil Town Vapi - 396191
Flat No.101, Shrushti Mahabharat Apartment
Adarshnagar, Borsi Road, Ward No.43 Rourkela - 769004, Orissa Mobile: +91 9601267911
Mahavir Garden to Mahavir College Road, Nagala Park
H.No.843, Nr. Panchsheel School : +91 661 2400880 E-mail: [email protected]
Kolhapur - 416003
Durg - 491001, Chattisgarh Mobile: +91 9437041724
: +91 231 2663330
Mobile: +91 9425016197 E-mail: [email protected] Vijayawada
Mobile: +91 9881465421
E-mail: [email protected] G-2, Shreya Tower, Moghalrajapuram
E-mail: [email protected] Salem Nr. Jammichettu Centre
Guwahati Ludhiana 3/25, Santosh Nagar, PACB Backside, Chinnathirupathi Vijayawada - 520010, Andhra Pradesh
G-1, Hill View Apartment Salem - 8 : +91 866 6629933
H.No.92, Lajpat Nagar, Near Bus Stand
Navagraha Path, Chenikuthi Hill Side : +91 427 2401981 Mobile: +91 9866463639
Ludhiana - 141002, Punjab
Guwahati - 781003, Assam Mobile: +91 9894617772 E-mail: [email protected]
: +91 161 2770574
Mobile: +91 9864110684 E-mail: [email protected]
Mobile: +91 9815502480
E-mail: [email protected] Vishakhapatnam
E-mail: [email protected] Sambalpur Flat No. 302, 48-3-37
Mobile: +91 9435346708 Pradhan Para, Near Jamkani Mandir
E-mail: [email protected] Ludhiana Ratna Towers, Sri Nagar
Beside LIC Div. Off, Ainthapalli Vishakhapatnam - 530 016, Andhra Pradesh
H.No.3746, First Floor, Sector-32-A, Chandigarh Road
Hardwar Sambalpur - 768004, Orissa : +91 891 6462229
Ludhiana - 141010, Punjab
6, Nand Puri, Nr. Aya Nagar Chowk, Jwalapur : +91 663 2541258 Mobile: +91 9849212555
: +91 161 5024702
Hardwar - 249407, Uttarkhand Mobile: +91 9438529778 E-mail: [email protected]
Mobile: +91 9780300771
: +91 1334 251943 E-mail: [email protected]
E-mail: [email protected]
Mobile: +91 9897070133 Vishakhapatnam
Ludhiana Surat Flat No.B4, 10-51-10, Mount Moriah Residency
E-mail: [email protected] Flat No. 202, D-1, Suryam Residence, Cause Way Road
H.No.3996, 1st Floor, Sector-32/A, Chandigarh Rd. Beside Latha Hospital, Woltair Uplands
Hubli Opp. Hari Darshan, Shinganpor-Dabholi Road, Katargam Viskhapatanam - 530003, Andhra Pradesh
Ludhiana
24, 2nd Cross Street, Kadashwar colony Surat - 395004, Gujarat : +91 891-2519762
: +91 161 5017742
Hubli - 580023, Karnataka Mobile: +91 9925001779 Mobile: +91 9849071221
Mobile: +91 9878098612
: +91 836 2282947 E-mail: [email protected] E-mail: [email protected]
E-mail: [email protected]
Mobile: +91 9880662047 Surat
E-mail: [email protected] Madurai
32, 33, Dattatrey Society
8/12, Ground Flr, Sakthi Vellammal Street, SS Colony
Mora Bhagal Char Rasta, Rander Road
Madurai - 625010, Tamil Nadu
Surat - 395005, Gujarat
Mobile: +91 9894617780
Mobile: +91 9879510191
E-mail: [email protected]
E-mail: [email protected]