Panel AUO T460HW04 V3 0 (DS)
Panel AUO T460HW04 V3 0 (DS)
com
( )Preliminary Specifications
Ϡ)Final Specifications
(Ϡ
Yenting Chiu
_________________________________ ____________________________________
Eugene CC Chen
____________________________________
Reviewed By Project Leader
Breeze Lin
____________________________________
Prepared By PM
Ryan Chung
____________________________________
Note 1: TST test fails to pass AUO internal qualification, so AUO cannot guarantee sub materials.ʳ
Note 2: Module MTBF test fails due to P-mura issue.ʳ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
3 ELECTRICAL SPECIFICATION
4 OPTICAL SPECIFICATION
5 MECHANICAL CHARACTERISTICS
7 INTERNATIONAL STANDARD
7-1 SAFETY
7-2 EMC
8 PACKING
9 PRECAUTION
9-5 STORAGE
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Record of Revision
Version Date Page Description
1.0 2010/7/6 First release
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
1. General Description
This specification applies to the 46.0 inch Color TFT-LCD Module T460HW04 V3. This LCD module has a TFT
active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 46.0 inch. This module supports
1,920x1080 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical
stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.
The T460HW04 V3 has been designed to apply the 8-bit 2 channel LVDS interface method. It is intended to
support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very
important.
* General Information
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
3. Electrical Specification
Below power input specification of T460HW04 V3 is employed to power the LCD electronics and to drive the TFT
array and liquid crystal.
Note :
1. The ripple voltage should be controlled under 10% of VCC
2. Test Condition:
(1) VDD = 12.0V
(2) Fv = 60Hz
(3) FCLK = 82MHz
(4) Temperature = 25 к
(5) Test Pattern : White Pattern
3. Measurement condition : Rising time = 400us
9''
*1'
μs
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
4. VICM = 1.25V
9 7+
9 ,&0
97/
9
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
ÎNS
LVDS Option = High/OpenÎ
& OR FN
& + [B 5 5 * 5 5 5 5 5 5 *
& + [B
& + [B * * % % * * * * * %
& + [B
& + [B
& + [B % % '( 1$ 1$ % % % % '(
& + [B
& + [B 5 5 1$ % % * * 5 5 1$
Note: x = 1, 2, 3, 4…
ÎJEIDA
LVDS Option = Low/GNDÎ
& ORFN
& +[B 5 5 * 5 5 5 5 5 5 *
& +[B
& +[B * * % % * * * * * %
& +[B
& +[B
& +[B % % '( 1$ 1$ % % % % '(
& +[B
& +[B 5 5 1$ % % * * 5 5 1$
Note: x = 1, 2, 3, 4…
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Notes:
(1) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2) Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
st st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3) If a period of DE “High” is less than 1920 DCLK or less than 1080 lines, the rest of the screen displays black.
(4) The display position does not fit to the screen if a period of DE “High” and the effective data period do not
synchronize with each other.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Rev. 10
T460HW04 V3 Product Specification
Page 11 / 26
7Y 0SL[HO
7EONY 7GLVSY
1 / LQ H
7K
'(
5*% /LQH ,QYDOLG'DWD /LQH /LQH /LQH /LQH /LQH ,QYDOLG'DWD
1 1
'DWD
&/.
7K
7FON
7GLVSK 7EONK
'(
3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO
&+ 0 0 0 0
,QYDOLG'DWD
0 0 0
,QYDOLG'DWD
3.4 Signal Timing Waveforms
Global LCD Panel Exchange Center
3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO
&+ 0 0 0 0
,QYDOLG'DWD
0 0 0
,QYDOLG'DWD
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
,QWHUIDFH6LJQDO W W W W W
/9'6'DWD &/.
9DOLG'DWD
*1'
W W
%DFNOLJKWRQRII
FRQWUROVLJQDO
9%/21
Values
Parameter Unit
Min. Type. Max.
t1 0.4ʳ ---ʳ 30ʳ ms
t2 0.1ʳ ---ʳ 50ʳ ms
t3 300ʳ ---ʳ ---ʳ ms
*1
t4 0 ʳ ---ʳ ---ʳ ms
t5 0ʳ ---ʳ ---ʳ ms
*2
t6 ---ʳ ---ʳ --- ʳ ms
t7 500ʳ ---ʳ ---ʳ ms
Note:
(1) T4=0 : concern for residual pattern before BLU turn off.
(2) T6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 4000 5000 -- 1
2
Surface Luminance (White) LWH -- * -- cd/m 2
Luminance Variation įWHITE(9P) -- -- * 3
Response Time (G to G) TȖ -- 6.5 -- Ms 4
Color Gamut NTSC * %
Color Coordinates
Red RX *
RY *
Green GX *
GY *
* *
Blue BX *
BY *
White WX *
WY *
Viewing Angle 5
x axis, right(ij=0°) șr -- 89 -- degree
x axis, left(ij=180°) șl -- 89 -- degree
y axis, up(ij=90°) șu -- 89 -- degree
y axis, down (ij=270°) șd -- 89 -- degree
* LED lightbar and LED Backlight structure is designed by customer, AUO could not guarantee
the typical value of luminance, NTSC, R/G/B/W.
** OPT spec. should refer to the ORT data gathered in the first 3 months after mass production.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all
pixels displaying white. From more information see FIG 2. LWH=Lon5 where Lon5 is the luminance with all
pixels displaying white at center 5 location.
3. The variation in surface luminance, įWHITE is defined (center of Screen) as:
įWHITE(9P)= Maximum(Lon1, Lon2,…,Lon9)/ Minimum(Lon1, Lon2,…Lon9)
4. Response time 7 ӫʳ is the average time required for display transition by switching the input signal for five
luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.
Measured Target
Response Time 0% 25% 50% 75% 100%
0% 0% to 25% 0% to 50% 0% to 75% 0% to 100%
25% 25% to 0% 25% to 50% 25% to 75% 25% to 100%
Start 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100%
75% 75% to 0% 75% to 25% 75% to 50% 75% to 100%
100% 100% to 0% 100% to 25% 100% to 50% 100% to 75%
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG3.
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T460HW04 V3. In addition the figures in the
next page are detailed mechanical drawing of the LCD.
Horizontal 1056.5 mm
Vertical 610.8 mm
Outline Dimension
Depth 20.8 mm (Front bezel to rib)
Horizontal 1024.08 mm
Bezel Opening
Vertical 579.27 mm
Horizontal 1018.08 mm
Active Display Area
Vertical 572.67 mm
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Front View
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Back View
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
25.4cm, 6 flats
8 Drop test (With carton) 1 (PKG)
(ASTMD4169)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
7. International Standard
7.1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including
electrical Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical
Commission
(3) EN 60950 : 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical
Standardization (CENELEC), EUROPEAN STANDARD for Safety of Information Technology
Equipment Including Electrical Business Equipment.
7.2 EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
1998
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
*xxxxxxxxxxxx-xxxx*
(2) For RoHs compatible products, AUO will add RoHS for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal green
team. (definition of green design follows the AUO green design checklist.)
B. Carton Label:
QTY: 7
7+:9
7;;;
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SFV0RGXOH(6'%DJ
SFV0RGXOH(6'%DJ
0RGXOH
7 pcs Modules
&XVKLRQWRS
&XVKLRQVHW
&XVKLRQGRZQ
ರ+ರ7DSH
SFVFDUWRQ
SFVFDUWRQ
FDUWRQ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
after packing 42(by Sea) 1180(L)mm*1150(W)mm*2466(H)mm (by Sea) 562.5 (by Sea) 40ft HQ
Stretch film
Corner angle
Pallet
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
5. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
(2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied
to module. And the case on which a module is mounted should have sufficient strength so that
external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit
broken by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the
surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials
like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the
adhesives used to attach front/ rear polarizer. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5 к and 35к at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they
be stored in the container in which they were shipped.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com