Antepartum Fetal Monitor

FM-2 (M2922A)
Antepartum Fetal Monitor
SERVICE GUIDE
M2922-9000B
Printed in Germany March 2002
Edition 1
Notice
Copyright © 2002 Philips Medizinsyteme Boeblingen GmbH. All rights reserved. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright holder.
Philips Medizinsyteme Boeblingen GmbH

Hewlett-Packard Strasse 2
71034 Boeblingen
Germany
Trademarks
Microsoft® is a U.S. registered trademark of Microsoft Corp.

Windows® and Windows NT® are U.S. registered trademarks of Microsoft Corp. All other product
and company names mentioned may be the trademarks of their respective owners.
Printing History
M2922-9000A . .08/01
M2922-9000B . .02/02
Conventions Used in This Guide
Warning
A warning alerts you to a potential serious outcome, adverse event or safety hazard. Failure to
observe a warning may result in death or serious injury to the user or patient.
Caution
A caution alerts you where special care is necessary for the safe and effective use of the product.
Failure to observe a caution may result in minor or moderate personal injury or damage to the
product or other property, and possibly in a remote risk of more serious injury.
Note— A note calls your attention to an important point in the text.

On your monitor, this sign indicates that there is detailed
information in this book which you must read before
proceeding with your task
Caution
US law restricts this device to sale by, or on the order of, a physician.
Contents
1. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Who Should Read This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
What to Do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Repair Strategy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warnings, Cautions, and Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Symbols and Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Packing for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Repacking in Original Carton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Repacking in a Different Carton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview Of The Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Block Diagram of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mechanical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
LCD and Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial I/O Communications Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Parallel I/O Communications Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Keypad and Navigation Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Measurements Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ultrasound Channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Toco Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mountings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Routine Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. System Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Serial I/O Communications Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Supported Modems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MultiTech Systems MT-5600ZDX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Nokia 6210GSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Parallel I/O Communications Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Contents v
3. Tests and Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Service Philosophy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Overview of the Service Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Checking the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Visual Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
FM-2 Power-On Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
What Happens During the Power-On Self Test . . . . . . . . . . . . . . . . . . . . . . . .20
Performing the Power-On Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Performance Test for Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Error Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Error Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4. Power-up Default Settings and the Service Menu . . . . . . . . 25

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Power-up Defaults Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Service Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Error Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
System A/D Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
5. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Initial Trouble Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Power Problem Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Diagnostic Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Diagnostic/Repair Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Monitoring Degradation Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Diagnostic Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Diagnostic Repair Actions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
6. Disassembly/Reassembly Guide . . . . . . . . . . . . . . . . . . . . . 37
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
How to Use this Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Closed Case Disassembly/Reassembly Procedures . . . . . . . . . . . . . . . . . . . . . . .40
vi Contents
Removing the Speaker Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Replacing the Speaker Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Removing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Battery Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Separation of Front and Rear Case Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . 45
Separation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Front Case Disassembly/Reassembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . 47
Removing the Navigation Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Replacing the Navigation Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Removing the Main PCB Assembly from the Front Case Assembly . . . . . . 49
Removing the LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Replacing the LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Replacing the Main PCB Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Removing the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Replacing the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Rear Case Disassembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Removing the Rear Connector PCB and the Interface Board . . . . . . . . . . 55
Removing the Interface PCB from the Rear Connector PCB . . . . . . . . . . . . 56
Replacing the Interface PCB on the Rear Connector PCB . . . . . . . . . . . . . . 56
Replacing the Rear Connector/Interface PCB Assembly. . . . . . . . . . . . . . . . 57
Removing the Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Removing the Foot Cushions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Main PCB Disassembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Removing the Side Panel and Side Connector PCB . . . . . . . . . . . . . . . . . . 59
Replacing the Side Panel/Side Connector PCB . . . . . . . . . . . . . . . . . . . . . . . 61
7. Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Small Parts Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Exchange Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Monitor (M2922A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Recorder (M2925A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Non-Exchange Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Supplies and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Breakdown of Spare Parts Kits by Component . . . . . . . . . . . . . . . . . . . . . . . . . . 66
M2922-64003 - Small Parts Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
M2922-64001 - Housing Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Contents vii
M2922-64002 - Speaker Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
M2922-40003 - Battery Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
M3921-60406 - Knob (Navigation Wheel) Kit . . . . . . . . . . . . . . . . . . . . . . . . .69
M2922-44301 - Keypad Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
M2922-64004 - Display Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
M2922-66505 - Side Connector PCB Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
M2922-66510 - Interface PCB Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
M2922-66511 - Rear Connector PCB Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Assembly Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
8. Test and Inspection Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
When to Perform Tests Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Battery Charging and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Using the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Low Power Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Recharging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Safety Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Safety Test Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Ground Integrity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Electrical Leakage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Safety Test 1: Enclosure Leakage Current Test . . . . . . . . . . . . . . . . . . . . . . .86
Safety Test 2: Patient Leakage Current Test . . . . . . . . . . . . . . . . . . . . . . . . . .88
System Safety Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Testing Transducers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Testing Toco Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Testing Ultrasound Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
viii Contents
List of Tables
Table 1 Fully wired DB9 RS-232 Null-modem pinouts . . . . . . . . . . . . . . . . . .14

Table 2 MultiTech MT-5600ZDX initialization string commands. . . . . . . . . .16
Table 3 FM-2 Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Table 4 Power-Up Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Table 5 Service Menu Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Table 6 Exchange Assemblies - M2922A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Table 7 Exchange Assemblies - M2925A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Table 8 Non-Exchange Assemblies - M2922A. . . . . . . . . . . . . . . . . . . . . . . . . .65
Table 9 Supplies and Accessories - M2922A . . . . . . . . . . . . . . . . . . . . . . . . . .66
Table 10 M2922-64003 Small Parts Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Table 11 M2922-64001 Housing Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Table 12 M2922-64002 Monitor Speaker Kit . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Table 13 M2922-40003 Battery Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Table 14 M2922-60406 Knob (Navigation Wheel) Kit . . . . . . . . . . . . . . . . . . . .69
Table 15 M2922-44301 Keypad Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Table 16 M2922-64004 Display Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Table 17 M2922-66505 Side Connector PCB Kit . . . . . . . . . . . . . . . . . . . . . . . .70
Table 18 M2922-66510 Interface PCB Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Table 19 M2922-66511 Rear Connector PCB Kit . . . . . . . . . . . . . . . . . . . . . . . .70
Table 20 FM-2: When to Perform Test Blocks . . . . . . . . . . . . . . . . . . . . . . . . . .80
Table 21 Test and Inspection Matrix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Table 22 Enclosure Leakage Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Table 23 Patient Leakage Current Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
List of Tables ix
List of Figures
Figure 1 FM-2 Block Diagram of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 2 Error Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Figure 3 System A/D Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Figure 4 Diagnosing Malfunction - Initial Diagnosis . . . . . . . . . . . . . . . . . . . . .32
Figure 5 Power Diagnosis - Power Supply or Display . . . . . . . . . . . . . . . . . . .33
Figure 6 Monitoring Degradation, Diagnostic Flow Chart . . . . . . . . . . . . . . . .35
Figure 7 Assembly Drawing (Sheet 1) - Top Level Assembly. . . . . . . . . . . . . .71
Figure 8 Assembly Drawing (Sheet 2) - Front Case Assembly. . . . . . . . . . . . .72
Figure 9 Assembly Drawing (Sheet 3) - Rear Case Assembly . . . . . . . . . . . . .73
Figure 10 Assembly Drawing (Sheet 4) - Interface PCB/Rear Connector PCB 74
Figure 11 Assembly Drawing (Sheet 5) - Side Connector PCB/Panel/Label . .75
Figure 12 Testing a Toco Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Figure 13 Testing an Ultrasound Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Figure 14 Position Of Crystals in an Ultrasound Transducer . . . . . . . . . . . . . .93
Figure 15 Testing the Crystals in an Ultrasound Transducer . . . . . . . . . . . . . .93
List of Figures xi
1
General Information
Introduction
This guide tells you how to service and repair the monitor (M2922A). It
describes the system hardware and software, tells you how to diagnose operating
and servicing problems, and how to test the system.
As this monitor is intended to be installed by the customer, refer to the
Instructions for Use for details of how to install the monitor.
The FM-2 Antepartum Fetal Monitor Service Guide supplements the
maintenance and troubleshooting procedures carried out by the operator that
are described in the Instructions for Use. Refer to the Instructions for Use for
maintenance and troubleshooting procedures that may be performed during
normal operation.
Any other maintenance and repair procedures beyond the level covered in the
Instructions for Use are limited to replacement of:
• the battery
• three board assemblies inside the case (but excluding the main PCB)
• the speaker
• components of the LCD display installed in the front case assembly
The features available on the monitor you are servicing depend on which
accessories were purchased. As this manual covers all accessories, consult your
configuration listing to see which apply to your monitor.
As the only support strategy for the Recorder is unit exchange, in the event of a
malfunction or failure, no repair or servicing information for it is included in
this manual. For routine care and maintenance, refer to the Instructions for Use.
Only qualified service personnel should attempt to disassemble the monitor, or
to remove or replace any internal assemblies.
Chapter 1 - General Information 1

Repair Strategy
Who Should Read This Guide

This guide is for any technical personnel servicing and repairing the FM-2
monitor (M2922A).
You must:
• understand English
• be familiar with standard medical equipment installation procedures
• be familiar with current conventional technical terms as used throughout
this guide
What to Do Next
Familiarize yourself with the contents of this guide before attempting to service
or repair the monitor.
Repair Strategy
Reading operating error messages and the error log helps to determine whether a
fault is a hardware or software problem. Fault rectification is accomplished by
replacement of the defective part at the assembly level. For example, faults may
be repaired by replacement of a complete board where the fault is identified, or
by exchanging the monitor.
Repair or replacement of individual components on the boards is not supported,
and should never be attempted.
There are no servicing instructions in this manual for the Recorder (M2925A) as
a repair is effected by exchanging the unit only.
After any repairs you must carry out the following tests:
• Power-On Self-Test (see “FM-2 Power-On Self-Test” on page 20)
• Performance tests (see “Testing Transducers” on page 90)
• Safety tests after repair (see “Safety Testing” on page 84)
2 Chapter 1 - General Information

Warnings, Cautions, and Notes
Warnings, Cautions, and Notes

This guide uses three terms that are important for proper servicing of the
monitor: Warning, Caution, and Note.
Warning
A warning calls your attention to an action or a possible situation that may
result in injury or death to you or the patient.
Caution
A caution precedes an action that may result in damage to, or malfunction
of the monitor. It indicates that special care is necessary for the safe and
effective servicing of the monitor.
Note—A note calls your attention to an important point in the text.
On your monitor, this sign indicates that there is

detailed information in this book and the Instructions for
Use which you must read before proceeding with your
task.

Symbols and Definitions
Symbols and Definitions
Symbol Definition Symbol Definition

Remote marker input Class II equipment symbol
connector symbol on (double insulation)
monitor
Drip-proof equipment Type BF applied part

classification on monitor symbol on monitor
Power input symbol on Refer to accompanying

power supply documents
220-240V~
50-60 Hz,
0.08A
Power supply connector RS-232 connector (symbol

symbol on monitor on monitor housing)
15V ∼ 1A RS-232
Power supply output RS-232 connector (symbol

connector on power supply on monitor label)
15V ∼ 1A
Functional earth symbol on Printer connection symbol

power supply on monitor
Indoor use only symbol

on power supply

Packing for Shipment
Packing for Shipment
General Instructions
To ship the monitor for any reason, follow the instructions in this section.
Pack the monitor carefully. Failure to follow the instructions in this section may
result in loss or damage not covered by the warranty. If the original shipping
carton is not available, use another suitable carton.
Repacking in Original Carton

If available, use the original carton and packing materials. Pack the monitor as
follows:
1. Place the monitor and, if necessary, accessory items in original packaging.
2. Place in shipping carton and seal carton with packaging tape.
3. Label carton with shipping address and return address.
Repacking in a Different Carton

If the original carton is not available, use the following procedure to pack the
monitor.
1. Place the monitor in a plastic bag.
2. Locate a corrugated cardboard shipping carton with at least 200 pounds
per square inch (psi) bursting strength.
3. Fill the bottom of the carton with at least 2 inches of packing material.
4. Place the bagged unit on the layer of packing material and fill the box
completely with packing material.
5. Seal the carton with packing tape.
6. Label the carton with the shipping address and return address.

Overview Of The Device
General Description
The device description included in this chapter focuses on the functional
performance of the replaceable assemblies that may be identified as the probable
cause of an apparent malfunction.
Refer to the Instructions for Use for information about the operation of the
monitor and of the Recorder. That manual includes descriptions of the
installation and setup of the monitor, modes of operation, recording of real-time
patient data, and transmission of patient data to local or remote PCs.

Block Diagram of Operation

Figure 1 illustrates the functional operation of the monitor, including the
accessories and options. It incorporates features of the mechanical design,
indicating the physical relationship of the assemblies and components.
Figure 1 FM-2 Block Diagram of Operation

Mechanical Description
As indicated in Figure 1, except for the battery, speaker, interface board, and rear
connector board, all functioning components of the monitor are installed as sub-
assemblies of the case front-cover assembly. There are four sockets (event marker,
Toco and two US) accessible on the left side panel. These are mounted on a side
connector PCB, which is itself mounted on the main PCB.
The case rear-cover assembly includes the replaceable battery and the speaker
assembly. The rear cover provides openings through which the three rear
connector board-mounted connectors (serial, parallel and power input) are
accessible. Additional mechanical features are included in
Chapter 6, “Disassembly/Reassembly Guide”.
LCD and Backlight

The LCD panel is a monochrome LCD display. It is a single-panel display with
a resolution of 320 X 240 pixels. Data to be displayed are stored in the main
board. Direct connection to the LCD panel is made through on-board header
assembly J7.
The backlight of the LCD is a Cold Cathode Fluorescent Lamp (CCFL)
mounted as part of the LCD panel. The AC high-voltage is turned on and off by
a digital control bit from the main-board-mounted drive.
Serial I/O Communications Port

The RS-232 interface is totally isolated from the interface board through the use
of high-speed optical isolators and isolated 5-volt power supply.
See Chapter 2, “System Interfaces” for serial connections, pinouts, cables and
supported modems.
Parallel I/O Communications Port

The parallel communications port is used to connect the monitor to the
Recorder or to a standard PCL Level 3 printer. At the time of printing, not all
PCL Level 3 printers are supported. For printers that have been validated for use

with the monitor, please see “Parallel I/O Communications Interface” on

page 18.
For further details of the pinouts and the cable specifications, see
Chapter 2, “System Interfaces”.
Keypad and Navigation Wheel

There are seven front-panel switches, two LEDs, and one wheel push-button
switch. All of these buttons go to the main-board except for the ON/OFF push
button, which goes directly to the power supply. The software monitors these
signals to determine which buttons were pushed. The two LEDs are located on
the control panel and inform the user of mains or battery operation.
The wheel consists of a mechanical rotary encoder wheel with a momentary
push button switch. As the knob is rotated, quadrature-coded outputs are
generated. The phase relationship between the two signals, in quadrature, reflect
the clockwise or counter clockwise rotation of the wheel. This relationship is
translated to move the cursor on the LCD display forward or backward,
depending on which way the wheel is rotated.
Power Supplies
The unit is operated from a 6-volt 4 AH sealed lead acid battery. The power
supply provides enough power to charge the battery even when the unit is
operating.
The monitor power is controlled by alternate button closures of the front panel
membrane switch. Unit operation starts only via a push of the front panel
button, but operation will stop after a delay of a few seconds when pushing the
front-panel membrane switch. This delay permits the main-board processor to
shut down in an orderly fashion, after storing the parameters and data, if any.

Measurements Channels
Measurements Channels
Ultrasound Channel
The monitor has two ultrasound sockets, US 1 and US 2, located on the side
panel of the monitor. Either one or two M1356A ultrasound transducers can be
connected. The latter case allows twins monitoring. (Refer to the Instructions for
Use for transducer specifications).
The transmitter pulsing the ultrasound transducer is gated by control circuitry,
and return signals are processed in the CODEC circuitry on the main board.
Toco Channel
The Toco circuit uses a Wheatstone bridge, with two strain gauge elements
mounted on a load beam. The differential output voltage is proportional to the
force applied to the load beam through the plunger. The Toco circuit is powered
from a single regulated 5V-supply excitation.
The amplified and filtered TOCO signal is converted by a 12-bit analog to
digital converter, providing an output scale of 2.56LSBs/gram.
Mountings
The monitor can be mounted in two ways using the following optional items:
• GCX roll stand (M3909A)
• GCX wall-mount (M3904A)
Refer to the fitting instructions that come with the relevant option.

Routine Maintenance and Cleaning
For detailed instructions on how to clean the monitor and the monitoring
accessories, see the Instructions for Use.
For instructions on cleaning the Recorder, refer to the Instructions for Use.


2
System Interfaces
Overview
The monitor has the following system interfaces:

• Serial I/O interface
• Parallel I/O interface
Note—The serial and parallel interfaces are not electrically isolated against
each other.
Serial I/O Communications Interface
The RS-232 interface is totally isolated from the interface board through the use
of high-speed optical isolators and isolated 5-volt power supply.
The RS-232 communications interface port is for communicating with:
• a desktop modem (see “Supported Modems” on page 14)
• a GSM cell phone modem (see “Supported Modems” on page 14)
• a PC/AT computer
The RS-232 communications protocol supports connections to OB TraceVue.
These connections are:
• direct (cable) connection to the OB TraceVue system, to supply real-time
patient data (System Online).
• via modem to supply complete patient records (System Batch).
It will also be used for software upgrades in the future.
Chapter 2 - System Interfaces 13

Supported Modems
The pinouts for the DB9 connector are shown in the following table.
Table 1 Fully wired DB9 RS-232 Null-modem pinouts
Connects
Pin Signal Details
to pin
1 and 6 4 DTR Data Terminal Ready

2 3 TxD Transmit data to external devices
3 2 RxD Receive data to external devices
4 1 and 6 DCD, DSR Data Carrier Detect, Data Set
Ready
5 5 Gnd RS-232 Ground
7 8 CTS Clear To Send
8 7 RTS Request To Send
9 9 - Ring indicator, not connected
The cable (M1380-61624) is a 3 meter long, fully wired RS-232 Null-modem

cable supplied with the viewer software. It is also available as an OB TraceVue
option.
Supported Modems
Note—As modems are not designed to fulfil the electrical requirements of a

medical device in terms of leakage current and isolation, a modem must be
located outside of the patient vicinity.
The following modems are the only modems that are currently validated and
supported:
14 Chapter 2 - System Interfaces

Supported Modems
• a MultiTech Systems MT-5600ZDX desktop modem

• a Nokia 6210GSM cellular phone modem (GSM type)
MultiTech Systems MT-5600ZDX
Modem The monitor sends the following default modem initialization string:
Default
Initialization ‘ATE0X4&K0\r’
String This is the first string sent by the monitor, and it is not customizable, nor is it
obvious to the user.
The monitor expects to see an “OK” come back from the modem after the
initialization string has been sent.
If an “OK” is returned to the monitor (that is, confirmation that a modem is
connected), the monitor then sends the user-customizable initialization string,
preceded by “AT” and followed by ”\r”.
The Attention characters, ‘AT’, at the beginning of the initialization string start
the command mode. The ‘\r’ at the end represents a Return, when the characters
entered in the command line and stored in the modem’s command buffer are
executed. The monitor always automatically enters the Attention (AT) and
Return (\r) characters.
Therefore, the user never needs to enter “AT” or “\r”.
The dialing also works in the same manner. The user never needs to enter the
return “\r” after the phone number. First, the monitor sends “ATD”, then the
user-entered phone number, then “\r”. “ATD” is simply the command to dial
with whichever dialing method is set as the default. (The default setting as
shipped is Tone dialing.)
If it is necessary to change the dialing method from Tone to Pulse, or vice versa,
then this is specified in the user-entered initialization string.
For example, to change to the Pulse dialing method, simply enter a P in the
modem initialization string.

Supported Modems
US Communications Menu
Data Transfer Stopped
Destination
150
Printer/Recorder
Set Modem Init String
Paper Output Current Record
Paper Speed (3 cm/min)
T X 0
Paper Style
ModemOKInitializationCancel Clear
Number to Dial
TOCO
20 (5) Return
cm JANE DOE 194848

3 min. 16:34:12 2/14/2001
The components of the default initialization string are explained in the

following table.
Table 2 MultiTech MT-5600ZDX initialization string

commands
Command Explanation
E0 Switches to verbose mode. To establish whether a modem

connection is effective, the modem replies to the signal sent
by the monitor with an ‘OK’ signal, or an error signal, rather
than just a result code (e.g. 0, 1, etc.). If an ‘OK’ is received,
then it is positive confirmation that the modem is connected
and functional.
X4 Switches to extended result codes, along with smart dialling.
The modem checks for a dial tone, dials, then checks for a
ring back or a busy signal after dialling.
This is not appropriate in local exchange branches.
X0 Selects basic result codes and blind dialling (dials even if there
is no line), as an alternative to use in local exchange branches.
&K0 No modem initiated flow control (disables the flow control).
For detailed information about the MultiTech Systems MT-5600ZDX and how
to set it, please refer to the modem’s Owner’s Manual.

Supported Modems
The commands above are only applicable to Rockwell/Conexant-based

MultiTech Systems modems. At the time of printing, the MultiTech MT-
5600ZDX is the only desktop modem that has been validated for use with the
monitor.
The monitor may also work with other modems, but this has not been tested,
and consequently no other modems are officially supported.
Customers may use any other modem after successful verification of several trace
transmissions.
Nokia 6210GSM
Instead of a conventional wired phone connection using a desktop modem, a
cellular phone can be used to transmit traces to the viewer or to OB TraceVue.
At the time of printing, the Nokia 6210GSM is the only cellular phone to date
that has been validated for use with the monitor.
Customers may use any other modem after they have successfully verified several
trace transmissions.

Parallel I/O Communications Interface
Parallel I/O Communications Interface
Caution
General-purpose personal computers and modems are not designed to
meet the electrical safety requirements of medical devices. The RS-232 and
parallel connectors on the monitor are electrically isolated to permit safe
connections to non-medical devices, which should be connected with a
cable of sufficient length to prevent the non-medical equipment from
contacting the patient.
If a non-medical device is connected to the serial port, a recorder or
printer connected at the same time to the parallel port should be located
outside the patient vicinity, as the two interfaces are not isolated against
eachother.
The parallel communications port is used to connect the FM-2 to the Recorder
or to a standard PCL Level 3 printer. Supported printers that have been
validated at the time of printing are:
• HP Deskjet 640c
• HP Deskjet 840c
• HP Deskjet 990 CXi
• HP Deskjet 980 CXi
• HP Deskjet 960c
• HP Deskjet 840c
• HP Deskjet 640c
• HP Deskjet 350
• HP Photosmart 1215
A standard PC parallel printer cable is used (IEEE-1284 compliant). This is
supplied with the recorder.
Although the same cable is used to connect the monitor to the Recorder or a
PCL Level 3 printer, a different protocol is used for communicating between the
monitor and the Recorder. This protocol does not conform to the IEEE 1284
norm, and is actually a serial connection.

3
Tests and Error Codes
Service Philosophy
If the monitor detects a problem, it displays an error screen that shows an error
reference number, and monitoring is discontinued. In addition, the errors are
written to the error log (see Table 3, “FM-2 Error Codes,” on page 23).
Read the system error log to determine whether the fault lies in the hardware or
firmware. These problems can be repaired by board replacement or unit
exchange. Do not attempt component-level board repair.
Overview of the Service Tests
A brief overview of the service tests that are used to verify performance following
repairs or during routine maintenance follows. All tests can be performed
without removing the covers of the monitor.
• Visual Test (see page 20)
• Power-On Self Test (see page 20)
• Performance tests for transducers, to check the processing of the signal from
the transducers (see “Testing Transducers” on page 90)
• Safety Tests
These test the electrical safety of the monitoring system and must be carried
out after upgrades and repairs. You must use a safety testing analyzer.
– System Safety Test (see page 89)
– Safety Test Blocks (see Table 21, “Test and Inspection Matrix,” on
page 81)
Chapter 3 - Tests and Error Codes 19

Checking the Battery
Checking the Battery
Before testing the monitor after repair or service, ensure that the battery itself is
not at fault. See “Battery Charging and Maintenance” on page 82.
Visual Test
Visually inspect the monitor and its accessories after a repair, and also on a
regular basis as part of routine maintenance. Ensure that the monitor, cables,
line cords, transducers and instruments have no visible evidence of damage that
may affect patient safety or monitoring performance. Do not use if there is any
sign of damage.
FM-2 Power-On Self-Test
When the monitor is turned on, it automatically performs a diagnostic self-test.

The self test continues during normal operation also. If the monitor fails its self
test, it will display an error screen, and will discontinue all monitoring
functions. In this case, it should be turned off and removed from service.
What Happens During the Power-On Self Test

• The executable program is loaded from flash memory into Random Access
Memory (RAM).
• A checksum algorithm is run to test the program just loaded into RAM.
• If the checksum test passes, the watchdog timer is started. The purpose of the
watchdog is to check that all tasks running concurrently on the monitor are
operating correctly.
20 Chapter 3 - Tests and Error Codes

FM-2 Power-On Self-Test
• The watchdog timer is allowed to time out, and the interrupt expected to
occur is verified to have occurred. Software will detect a watchdog failure if
the watchdog timer does not expire within a specified amount of time.
Performing the Power-On Self Test

1. Press the On/Off button .
2. Initially the LCD screen illuminates, but is blank.
3. After two or three seconds, the monitor plays a two-tone power-on jingle
while performing the Power-On Self Test. At this point, the monitor
displays the start-up screen, showing the Agilent logo, bootcode version
and the application version.
4. Upon successful completion of the Power-On Self Test, the display will
show the main monitoring screen.
5. If an error is detected, the monitor will display the error screen.
6. The error number is stored in the error log (see Table 3, “FM-2 Error
Codes,” on page 23).
If the Power-On Self Test fails, try to cycle power again. If it fails again, then
exchange the monitor.

Performance Test for Transducers
Performance Test for Transducers
This tests the signal path to and from the transducers.

1. Turn on the monitor and the recorder or printer.
2. Connect one or two US cables and the TOCO transducer.
3. Check that the display acknowledges the connected transducers in the

appropriate frames.
Also refer to “Testing Transducers” on page 90.
Error Handling
There are two types of error that you may see: those that the monitor cannot
self-detect, and those that it can self-detect.
• If an operational error occurs that is not self-detected, the monitor shuts
down. There will be no audible or visual warnings or indicators.
• If a self-detectable error occurs, the monitor will do the following:
– Display the error screen
– Sound an error tone
– Discontinue all monitoring functions

Error Codes
Error Codes
The error codes are primarily intended for diagnostic use at the factory. The
errors, their explanation, and any service action required are shown in the
following table.
Table 3 FM-2 Error Codes
Error
Explanation Action
Code
1 Monitor’s memory has become corrupt

2 Invalid internal software state in the monitor
3 Unable to acquire a software resource
(queue, semaphore, etc.)
4 Stack overflow
Replace the monitor
5 Bad parameter value passed to a function
6 Software is in an unexpected state
7 Software assertion was false (coding error)
8 A task failed to check in with the watchdog timer
9 The CRC of the software in memory is invalid
10 A voltage is out of range Check the battery and the
power supply for correct opera-
tion. Replace if necessary
11 Watchdog timer is not functioning
12 System received too many resets
13 Recorder's software version number is incompatible Replace the monitor
with the monitor
14 Flash memory type is incompatible with the software
15 Phase lock loop lost lock (non-critical error) No action required

Error Codes
Table 3 FM-2 Error Codes
Error
Explanation Action
Code
16 Failed to allocate requested memory

17 A problem with the Codec has been detected
18 High half-word of flash failed to program
Replace the monitor
19 Low half-word of flash failed to program
20 High half-word of flash failed to verify
21 Low half-word of flash failed to verify
30 Error in communications micro-controller Check the side connector PCB.
Replace if necessary.
50 Corrupt patient record (trend file)
51 Corrupt file system
52 Attempt to read a deleted file None: factory diagnostic infor-
53 File system wrapped memory mation only
54 Attempt to read a corrupt file

55 Failed to create a file
70 File corrupted - FM-2 viewer communication error
71 Invalid Patient ID - FM-2 viewer communication
error None: factory diagnostic infor-
72 Invalid sequence number - FM-2 viewer communi- mation only
cation error
73 Remote error - FM-2 viewer communication error
1xx Algorithm errors
2xx Printer errors None: factory diagnostic infor-
3xx Fatal Operating system errors mation only
4xx Fatal processor exceptions

4
Power-up Default Settings and the
Service Menu
Introduction
This section discusses use of the Power-up Defaults Menu to configure power-
on default settings, and the Service Menu to obtain service-related information
about the monitor.
Power-up Defaults Settings

These are parameters which can be changed by the user. The power-up defaults
allow you to create a power-up default for many settings in the monitor. Power-
up defaults are the settings in effect each time the monitor is powered on.
The power-up default settings are configured at the factory prior to shipment.
Some of the parameters are stored when the monitor is powered down, and these
are classified as “saved through power cycle”. The factory default values are
defined in Table 4.
Table 4 Power-Up Default Settings
Parameter Factory Default Saved Through Power Cycle
US trace separation “0”BPM No
TOCO Baseline set-point 5 Yes

All alarm settings - Yes
Modem: Initialization string ----- Yes
Modem: Phone number ----- Yes
Chapter 4 - Power-up Default Settings and the Service Menu 25

Service Menu
Table 4 Power-Up Default Settings
Parameter Factory Default Saved Through Power Cycle
Data transfer Disabled Yes (if real-time transfer)
Data Transfer Destination Recorder/ Yes

Printer
Recorder: Paper speed 3 cm/minute Yes
Recorder: Paper style US Yes
Time format 12 hour Yes

Date “today” Yes
Date format mm/dd/yy Yes
Patient ID time/date encoded No
Language Configured language Yes
Service Menu
The purpose of the Service Menu is to allow factory, field-service, and hospital
biomedical technicians access to a series of test and system-related information
screens for the purpose of verifying monitor performance or troubleshooting
problems.
To access the Service Menu, press the navigation knob when the Power Status
Frame is selected. The following can be viewed from the Service Menu:
26 Chapter 4 - Power-up Default Settings and the Service Menu

Service Menu
Table 5 Service Menu Entries
Menu Item Explanation
View Error Log Displays the error log menu

View A/D Values Displays the Analog-to-Digital (A/D)
Menu
System On-Time Elapsed system on-time (expressed in
hours).
System on-time is not reset to 0 after the
battery is replaced, but is retained. This
value is saved through power cycles.
Language English
German
Spanish
Italian
Portuguese
French
Russian
Simplified Chinese
Traditional Chinese
Japanese
Demo Mode Choice of On or Off
The Service Menu lists the test and system-related information screens. Selection
of an item in the menu will invoke that test or information screen. The test and
information screens that appear in the Service Menu are as follows:
• Error Log
• System Analog-to-Digital (A/D) Values

Service Menu
Error Log
This screen displays the eight most recent error code types, logged by the
monitor. After eight error code types have been logged, the oldest error code
type will be deleted as new error code types are added. Adjacent to each error
code will be an entry which is the number of occurrences of that error. This
means that if there are many occurrences of one type of error code, that one
error code won’t overwrite the other seven error codes.
Next to the occurrence field is the time and date of the most recent occurrence
of the error code. Error codes may not be changed or reset in this screen. When
in the Error Code screen, the Return item is always highlighted; a press of the
wheel will return the user to the Service Menu. Rotating the wheel while in the
Error Code screen will have no effect.
Figure 2 Error Log
Refer to “Error Codes” on page 23, for more information on error codes.

Service Menu
System A/D Values

For the end user or service personnel, the system A/D values require no
interpretation.
The A/D screen displays the current value of each analog-to-digital

(A/D) channel in volts. The A/D channels read DC voltages, for example, power
supply voltages and battery voltage. The A/D values displayed are static, being
acquired when the screen is first displayed.
None of the displayed values may be changed or reset in this screen.When in the
A/D screen, the Return item is always highlighted; a press of the wheel will
return the user to the Service Menu. Rotating the wheel while in the A/D screen
will have no effect. The A/D Values screen appears as follows:
Figure 3 System A/D Values
Note—The screenshot above shows untypical system A/D values that are
not representative of normal operation.

Service Menu

5
Troubleshooting
General
This section provides a guide for qualified service personnel in locating the
possible cause of an apparent malfunction of the monitor or its accessories. Use
of built-in diagnostics, flow charts, and step-by-step procedures are provided as
aids in the troubleshooting process.
The chapter leads you to a probable field replaceable assembly or component.
Items that are serviceable only at the factory are also identified, as well as
instructions for their return for repair/replacement.
The initial analysis determines whether the apparent malfunction is caused by a
replaceable accessory, or by a replaceable assembly within the monitor case.
Chapter 5 - Troubleshooting 31
General
Initial Trouble Diagnosis

The first step in diagnosing a possible malfunction is to duplicate, if possible,
the symptoms of the reported malfunction. Thereafter, it is important to
categorize the problem as either one of two types, as illustrated in Figure 4. They
are:
• Totally inoperative condition, or
• Degraded operation.
The totally inoperative condition is indicated by the failure of the monitor to
respond to the power ON front-panel action, or by complete loss of monitoring
functions during operation. Contact your local Agilent Response Center.
Degraded operation performance might be indicated by the appearance of
artifacts in the display, or by gaps in the pixel display, by intermittent actions, or
by obviously inaccurate measures of fetal activity, etc.
Figure 4 Diagnosing Malfunction - Initial Diagnosis
32 Chapter 5 - Troubleshooting
Power Problem Diagnosis
Diagnostic Flow Chart

The flow chart of Figure 5 shows a sequence of actions and decisions you can use
after the initial diagnosis of a “total failure” as a power supply or display
problem.
Note—If the apparent “total failure” is caused by a malfunctioning display

backlight, you may see a faintly lit display with the appropriate Power-On
Self Test message. The troubleshooting under these circumstances is
described in this section.
Figure 5 Power Diagnosis - Power Supply or Display
Diagnostic/Repair Actions
Examine Reduce background room illumination. If only the back light fluorescent tube
Display or its high voltage driver has failed, the display may be faintly visible.
Intensely
Refer to page 50 for removal procedures.
Replace Refer to page 43.

Battery
Exchange the If the display is not at all visible, and there is total failure, exchange the monitor.
Monitor
Monitoring Degradation Problems
Diagnostic Flow Chart

Figure 6 illustrates a logical sequence of troubleshooting diagnostics when the
monitor appears to be operative, but the displayed results are suspect for any
number of reasons. The resulting diagnosis will result in replacing either the
monitor or the transducers.
Figure 6 Monitoring Degradation, Diagnostic Flow Chart
Diagnostic Repair Actions
Describe Examine the display after an apparently successful power up sequence and self-
Degraded test.
Performance
Consider, first, the appearance of artifacts, gaps, or general quality of the display.
Note the values being reported in the numerical frames (FHR(s)) and TOCO).
Are they clearly unreasonable?
Swap Use a spare transducer that is free of defects and meets factory specifications. At
Transducers facilities where more than one monitor is installed, it may be convenient to
borrow a transducer that is working satisfactorily with another monitor.
Exchange the If the monitoring problems persist, or there is total failure, exchange the
Monitor monitor.
6
Disassembly/Reassembly Guide
Warning
Performance verification: do not place the monitor into operation after
repair or maintenance has been performed, until all performance tests and
safety tests listed in Chapter 8 of this service manual have been performed.
Failure to perform all tests could result in erroneous monitor readings, or
patient/operator injury.
Warning
Energized circuits are accessible with the covers open. Do not work on the
monitor with the covers open. Only qualified service personnel should
open or disassemble the monitor.
Introduction
Warning
Before attempting to open or disassemble the monitor, disconnect the
power supply from the monitor.
Warning
High voltage is generated by the LCD backlight driver. Do not operate the
monitor with the covers open.
Chapter 6 - Disassembly/Reassembly Guide 37

How to Use this Chapter
Caution
Observe ESD (electrostatic discharge) precautions when working within
the unit.
Caution
Important for disassembly! When disassembling the monitor, make sure
that the battery leads are disconnected. Otherwise, it is likely that circuit
damage will occur.
The monitor can be disassembled down to all major component parts,

including:
• PCBs
• battery
• cables
• function buttons
• chassis enclosures
Remember to store all screws, nuts, washers and other parts in a safe place for
later refitting.
How to Use this Chapter

The step-by-step procedures that are used to access replaceable parts of the
monitor are illustrated in the Disassembly sections which follow. These describe
and photographically illustrate procedures for disassembling the monitor to
enable removal and replacement of suspected defective assemblies and
components.
The monitor consists of two main assemblies:
• The front case assembly
• The rear case assembly
The main PCB assembly is separable from the front case assembly.
38 Chapter 6 - Disassembly/Reassembly Guide

Tools Required
All part numbers and exploded views of some assemblies are found in
Chapter 7, “Spare Parts”.
Tools Required
Caution
When reassembling, be sure to follow torque-limits instructions. Excessive
torque may damage the plastic screw mountings or case.
The following tools are required:

• small/medium, Phillips-head screwdriver
• A torque-sensitive tool, with a torque range to 1.1 Nm (10 in-lb.); accuracy
±0.1 Nm (±1 in-lb.)
• needle-nose pliers or Tinnerman tool
• 10 mm socket driver (for wheel encoder nut)
• 3/16” socket driver
The rear case assembly consists of a molded plastic case, in which the battery is
stored. The speaker housing is mounted on the back of the rear case assembly,
and also forms the cover for the battery. Through-holes in the case cover are
provided for the rear-panel connectors, that are mounted on the rear connector
board.
Fuses
There are no customer or field-replaceable fuses.

Closed Case Disassembly/Reassembly Procedures

This section describes the items that may be removed without disassembling the
main case of the monitor.
The speaker housing is attached to the back of the rear case. The speaker
housing also acts as the battery cover. To gain access to the battery, first remove
the speaker housing (see “Removing the Speaker Housing” on page 41).
Caution
Important for disassembly! When disassembling the monitor, make sure
that the battery leads are disconnected. Otherwise, it is likely that circuit
damage will occur.
Caution
Important for reassembly! If the internal battery cable has been
disconnected, pay very careful attention to the polarity of the cable before
reattaching. The red wire connects to the +ve terminal, the black wire
connects to the -ve terminal. If the battery cable polarity is reversed, circuit
damage will occur. Circuit damage caused by reversed polarity is not
covered by the warranty.

Removing the Speaker Housing

Step 1. Place the monitor on its front panel, being careful not to place the unit
on any surface that will damage the display.
Step 2. Using the Phillips-head screwdriver, unfasten the two screws securing
the speaker housing. The speaker housing also acts as the battery cover.
Step 3. Gently lift the bottom (screw) end of the speaker cover just enough for
the battery pad (attached to the inside of the speaker housing) to clear
the bottom of the rear case. At the same time, slide the speaker housing
towards the bottom of the rear case to free the two lugs holding the top
of the speaker housing. The speaker housing is now free of the rear
case, but with the wires still connected.
Step 4. Carefully disconnect the speaker wires by sliding the spade connectors
off the speaker terminals.
Step 5. The speaker housing is now completely free of the rear case.

Replacing the Speaker Housing

Step 1. Connect the speaker cables by pushing the spade terminals onto the
speaker terminals in the speaker housing. Check that they are secure.
The wires are not coded for polarity, as the polarity is uncritical.
Speaker housing
lugs
Speaker
terminals
Step 2. Refit the speaker housing by sliding the two metal lugs at the top end
of the speaker housing under the lip at the top of the battery housing
aperture until it stops.
Step 3. Secure the speaker housing with the two fastening screws. Torque the
screws to 0.7 to 0.9 Nm (6 to 8 in. lb).
Caution
Do not overtorque the screws, as the plastic screw mountings or the casing
may be damaged.

Removing the Battery

Step 1. Place the monitor upside down so that its top is resting on the work
surface. In this position, the monitor leans back at a convenient angle
that allows easy removal of the battery with the aid of gravity.
Step 2. While the monitor is in this tilted position, the battery will normally
fall partly out of its housing. If it does not, then apply a little pressure
on the terminal-end of the battery (nearest the work surface). This
should cause the battery to fall partly out of the case.
Step 3. Carefully remove the battery from the monitor. Take care not to put
too much stress on the battery wires as you take the battery out of the
case.
Step 4. Disconnect the battery cables by sliding the spade connectors off the
battery terminals.
Caution
During reassembly, pay very careful attention to the polarity of the battery
cable before reattaching. The red wire connects to the +ve terminal, the
black wire connects to the –ve terminal. If the battery cable polarity is
reversed, circuit damage will occur. Circuit damage caused by reversed
polarity is not covered by the warranty.

Replacing the Battery

Step 1. Connect the battery cables to the replacement battery, paying careful
attention to cable polarity. Connect the red cable to the positive
terminal, marked in red. Connect the black cable to the negative
terminal, marked in black.
Step 2. Carefully place the new battery into the battery housing.
Step 3. Reconnect the speaker and refit the speaker assembly. (See “Replacing
the Speaker Housing” on page 42).
Battery Disposal
Refer to practices and procedures used at the local institution when disposing of
the battery.
Please conform to any local laws and requirements governing the disposal of lead
acid batteries.

Separation of Front and Rear Case Assemblies
Separation
This section describes the procedures required to separate the front and rear case
assemblies of the FM-2 monitor.
Step 1. Remove the speaker housing (see “Removing the Speaker Housing” on
page 41).
Step 2. Remove the battery (see “Removing the Battery” on page 43).
Step 3. Remove the four screws fastening the rear case assembly to the front
case assembly using a Phillips-head screwdriver.
Step 4. Separate the front and rear case assemblies.
Front case
assembly
Rear case
assembly
Groove
Connector panel
Note—The US and Toco sockets protrude slightly from the face of

the connector panel on the side of the monitor. While separating the
front and rear case assemblies, you may feel some resistance at the
connector panel end of the monitor, in which case gently raise the
handle end of the rear case assembly to help to clear the sockets.
Step 5. If the silicone tubing seal is to be replaced, remove it.

Reassembly
Step 1. Ensure that the cables for the speaker and the battery are correctly
routed and accessible from the rear of the case for later connection.
Step 2. Confirm that the patient connector PCB is firmly mated to the main
PCB. (There should be no gap between the bottom of the patient
connector PCB and the main PCB).
Step 3. Carefully align the groove in the connector panel with the edge of the
corresponding opening in the rear case moulding. Take care that it
stays aligned while you push the front and rear case assemblies
together. When the reassembly is complete, the edge of the case
opening should sit evenly in the groove of the connector panel.
Step 4. Align the ridge in the front case assembly with the groove in the rear
case assembly.
Step 5. Check that the four screw holes align correctly.
Step 6. Drive in the four screws that hold the front and rear assemblies
together. Torque the screws to 0.7 to 0.9 Nm (6 to 8 in. lb).
Caution
Do not overtorque the screws, as the plastic screw mountings or casing
may be damaged.
Step 7. Refit the battery (see “Replacing the Battery” on page 44).
Step 8. Refit the speaker housing (see “Replacing the Speaker Housing” on
page 42).

Front Case Disassembly/Reassembly Procedures

This section describes how to remove/replace items from the front case assembly.
The front case assembly includes the replaceable molded front-case, the main
PCB, the LCD assembly, the front-panel keypad and the navigation wheel.
First separate the front and rear case assemblies as described in the section
“Separation of Front and Rear Case Assemblies” on page 45.
Removing the Navigation Wheel

The wheel is a friction fit on the stem of the encoder. The encoder is attached to
the main circuit board and has a threaded moulded base just below the rotating
stem of the encoder. The threaded base accepts a 10 mm nut which fastens the
encoder assembly to the front bezel.
Step 1. From the front, remove the wheel by grasping the sides of the wheel
firmly and pulling straight back from the monitor.
If the wheel is not easily removable by hand, a small flat-headed
screwdriver may be used to gently pry off the wheel. If necessary, apply
some adhesive tape to the front cover and/or the head of the
screwdriver to prevent any damage.
Step 2. Use a 10 mm hex socket or suitable closed spanner to unscrew the
fastening nut on the outside of the front bezel.
Encoder shaft
10 mm nut

Replacing the Navigation Wheel

Step 1. If the front case assembly has been disassembled, refit the LCD
assembly (see “Replacing the LCD Assembly” on page 51) and the
main circuit board (see“Replacing the Main PCB Assembly” on page
52) to the front case assembly.
Step 2. Screw the 10 mm nut onto the threaded base of the encoder switch
from the outside of the front bezel, initially by hand.
Caution
Do not overtorque. If excessive torque is applied to the encoder nut,
damage will occur to the encoder switch. Do not exceed the maximum
allowable torque setting.
Step 3. Using a torque-sensitive tool, torque the nut to 0.2 Nm (28.3 oz. in.).
Step 4. Push the navigation wheel onto the shaft of the encoder.

Removing the Main PCB Assembly from the Front Case Assembly
Step 1. Remove the navigation wheel (see “Removing the Navigation Wheel”
on page 47).
Step 2. Place the front case assembly with the bezel face down on the work
surface. Take care not to damage the display.
Step 3. Disconnect the backlight power supply cable connector from J4 on the
main PCB.
Step 4. Disconnect the keypad ribbon cable connector from J6 on the main
PCB. To remove the cable from the connector, first release the locking
cap to loosen the cable. Slide the cable out, leaving the cap loosely
seated in the connector.
Step 5. Use a Phillips-head screwdriver to remove the screw holding the main
PCB assembly in place in the front cover assembly.
Connector J7 is on the
underside of the board here
Keypad ribbon cable Backlight power supply

at J6 on main PCB at J4 on main PCB
Step 6. Remove the main PCB by gently pulling upwards to disconnect the
multipin LCD assembly connector at J7 on the main PCB. Pull
straight up to avoid bending the pins.
There are now three separate items:
• Front case assembly
• Rear case assembly
• Main PCB assembly

Main PCB
Rear case assembly
assembly
Front case
assembly
Removing the LCD Assembly
Warning
High voltage is generated by the LCD backlight driver. Do not operate the
monitor with the covers open.
The Display Kit (M2922-64004) comes with a replacement display window,

which should be replaced when the LCD assembly is replaced.
Step 1. Use a Phillips-head screwdriver to unfasten the four corner screws.
LCD assembly Screws

Main PCB
assembly
Step 2. Remove the LCD assembly, providing access to the display window.

Step 3. Remove the display window by carefully prying up one corner and
then peeling back.
Front bezel
LCD
assembly
Display
window
Replacing the LCD Assembly

Step 1. Fit the new display window with its gasket to the inside of the front
bezel. The display window comes with its own double sided adhesive.
Step 2. Position the LCD assembly so that the holes in each corner align with
the four screw mounts on the inside of the front bezel.
Step 3. Using a Phillips-head screwdriver, fasten the LCD assembly with the
four fixing screws.

Replacing the Main PCB Assembly

Step 1. If the LCD assembly has been removed, first replace it. (See “Replacing
the LCD Assembly” on page 51).
Note—There are two notches on the main PCB, used for location
purposes. One is at the patient connector panel end, and the other is on
the opposite end. There are two corresponding guides in the front cover.
Step 2. Align the location notch at the patient connector end of the main PCB
with the guide in the front cover, while keeping the opposite end of
the main PCB slightly raised and clear of the LCD connector pins (J7
on the main PCB).
Step 3. At this stage, check that the cables and connectors for the LCD
backlight power supply and the front keypad do not get trapped
underneath the main PCB, but are free and accessible from the side of
the main PCB.
Step 4. With the guide in the front cover still located in the notch at the
patient connector end of the main PCB, carefully align the connector
J7 on the main PCB with the corresponding pins on the LCD
assembly.
Step 5. Press down gently until the connector at J7 on the main PCB is fully
seated on the pins on the LCD assembly. Check that the notch at the
handle end of the main PCB aligns with the guide in the front cover,
and that the fixing holes in the main PCB align with the four screw
mounts in the front cover. This will confirm that the J7 connector is
correctly located. Also check that the navigation wheel shaft is centred
in the hole in the plastic bezel recess, so that the refitted wheel does not
bind with the case.
Step 6. Using a Phillips-head screwdriver, fasten the fixing screw to the screw
mount in the front cover at the handle end, nearest to the navigation
wheel/encoder switch.

Notch &
guide Notch
& guide
Main PCB screw

fixing
Backlight
Keypad ribbon cable power
& connector connector
Step 7. Reconnect the backlight power supply connector to J4 on the main

PCB. It is only possible to fit the connector one way round.
Step 8. Reconnect the keypad ribbon connector by inserting the ribbon cable
fully into the connector at J6 on the main PCB through the locking
cap which was left loosely fitted to the connector during disassembly.
Slide the locking cap forward to secure the ribbon cable.

Removing the Keypad

The keypad is attached to a recess in the front cover assembly by an integral
double sided adhesive.
Step 1. From the face of the front bezel, carefully pry up one corner of the
keypad, then peel it away from the front cover.
Note—The keypad is made up of a number of different layers, which may

separate during removal. Ensure that all layers are removed completely
before a replacement is fitted.
Replacing the Keypad

Step 1. Ensure that the recess in the front bezel for the keypad is clean.
Step 2. Thread the ribbon cable through the slot in the front cover.
Step 3. Carefully align one end of the keypad with the corresponding edge of
the recess in the front bezel, and carefully stick the keypad down,
working from one end to the other to avoid air bubbles.

Rear Case Disassembly Procedures

This section describes the items that may be removed/replaced on the rear case
assembly of the monitor. First separate the front and rear assemblies as described
in the section “Separation of Front and Rear Case Assemblies” on page 45.
Removing the Rear Connector PCB and the Interface Board

The interface PCB is connected at right angles to the rear connector PCB, and is
separable from it.
Step 1. From outside the rear cover, use a 3/16 socket driver to remove the
two standoff fasteners of the RS-232 connector, and also the two
standoff fasteners of the parallel connector.
Standoff
fasteners
Step 2. From inside the rear cover, remove the rear connector PCB and the
interface PCB connected to it.

Removing the Interface PCB from the Rear Connector PCB

Step 1. Using a Phillips-head screwdriver, remove the two screws on the
connector side of the connector PCB.
Rear connector
board
Interface board
Screws
Step 2. Separate the two boards by disconnecting the two multi-pin

connectors at J1 and J2 on the rear connector PCB. Ensure that you
pull straight, with no twisting action, so that the pins do not get bent.
Interface
board
Rear connector
board
Replacing the Interface PCB on the Rear Connector PCB

The refitting procedure is the reverse of the removal procedure.

Replacing the Rear Connector/Interface PCB Assembly

Step 1. Place the rear connector/interface PCB assembly into the dedicated
recess inside the rear case assembly. See that the RS-232, parallel and
power supply connectors fit into their respective slots in the rear case.
Step 2. From outside the rear case, use a 3/16 socket driver to refit the two
standoff fasteners of the RS-232 connector, and the two standoff
fasteners of the parallel port to secure the rear connector PCB in place.
Step 3. Ensure that the speaker cable connector is secure on the interface PCB.
Check that the two pins on the board are perpendicular to the board,
or leaning slightly towards the connector latch. This will ensure a firm
connection.
Step 4. Route the cables for the speaker and the battery.
Speaker cable connector

Connector latch

Removing the Handle

Each end of the handle is a friction fit on a cross-shaped boss.
Step 1. Use flat-bladed screwdriver to carefully pry one end of the handle.
Step 2. When the end of the handle has begun to loosen from the boss, use the
same technique to begin to pry up the other end.
Step 3. Alternately apply this prying action between each end of the handle
until the handle is free of the rear case.
Removing the Foot Cushions

The foot cushions are attached with an adhesive to the bottom surface of the
rear cover, and can be removed by lifting one end of the foot and peeling off.
Foot cushions

Main PCB Disassembly Procedures

This section describes the items that may be removed/replaced from the main
PCB assembly of the monitor. The main PCB assembly is separable from the
front case assembly.
Step 1. First separate the front and rear assemblies as described in the section
“Separation of Front and Rear Case Assemblies” on page 45.
Step 2. Then remove the main PCB assembly from the front case assembly, as
described on page 49.
Removing the Side Panel and Side Connector PCB

Step 1. Use needle-nose pliers or a Tinnerman tool to remove the two
Tinnerman fasteners securing the white plastic side panel to the
underside of the main PCB.
Tinnerman nut
Step 2. The side panel is attached by screws to the side connector PCB.
Remove this assembly from the main PCB by pulling it straight up,
disconnecting the multipin connector at J3 on the main PCB.

J3
on
main
PCB
Step 3. Use a Phillips-head screwdriver to remove the six screws that secure the
side panel to the socket surrounds. Access to the screws is gained
through the holes in the side connector PCB.
Step 4. Remove the side panel from the side connector PCB.

Replacing the Side Panel/Side Connector PCB

Step 1. Place the side panel on the side connector PCB so that the sockets on
the side connector PCB fit the holes in the side panel.
Step 2. Using a Phillips-head screwdriver, fasten the side connector PCB to
the side panel using the six screws.
Step 3. Align the studs on the bottom of the side panel with the holes on the
main PCB. Also align the pins at J3 on the main PCB with the
corresponding multipin connector on the side connector PCB.
Step 4. Push down until the pins at J3 on the main PCB are fully mated with
the multipin connector on the side connector assembly. There should
be no gap between the bottom of the side connector PCB and the
main PCB. Ensure that the side connector PCB is perpendicular to the
main PCB.
Step 5. From underneath the main PCB, fit a new Tinnerman nut to each of
the two side panel studs located in the holes on the main PCB. Ensure
that the side panel PCB remains perpendicular to the main PCB
surface, and that the side panel is held firmly by the Tinnerman nuts.


7
Spare Parts
Introduction
Spare parts, along with part numbers, are listed in the tables that follow. “Item
No.” corresponds to the callout number in Figure 7 through Figure 11. The
“Page Ref.” indicates the page number of the relevant disassembly procedures in
Chapter 6.
Small Parts Kit

Most small parts and hardware (screws, and so forth) can be found in the Small
Parts Kit, Part Number M2922-64003. The Small Parts Kit is supplied with
every major spare part.
Chapter 7 - Spare Parts 63

Exchange Parts
Exchange Parts
Monitor (M2922A)
Table 6 Exchange Assemblies - M2922A
Exchange Part No. Description

M2922-68000 Entire monitor
M1355-69011 TOCO Transducer
M1356-69011 US Transducer
Recorder (M2925A)
Table 7 Exchange Assemblies - M2925A
Exchange Part
Description
No.
M2925-68110 Recorder 100V, 120V
M2925-68220 Recorder 220V, 240V
64 Chapter 7 - Spare Parts

Non-Exchange Parts
Non-Exchange Parts
Table 8 Non-Exchange Assemblies - M2922A
Item Page
Part No. Description
No. Ref.
1 M2922-66505 Connector board 59, 61
2 M2922-66510 Interface board 56
3 M2922-40003 Battery 43, 44
4 M3921-60406 Navigation wheel 47
- M2922-64001 Housing kit -
5A & 5B M2922-64004 Display assembly kit 50, 51
6 M2922-64002 Speaker kit 41, 42
7 M2922-44301 Key pad 54
- M2922-64003 Small parts kit -
8 M2922-60511 Rear connector board 55, 57
- M3921-61000 Power supply 100V - 120V
- M3921-61010 Power supply 220V - 240V
- M1380-61624 Serial interface cable to PC, -
OB TraceVue and FM-2
viewer
- 15249A Event marker -

Supplies and Accessories
Supplies and Accessories
Table 9 Supplies and Accessories - M2922A
Part No. Description

M1356-43203 Transducer knob adapters (3-pack)
Breakdown of Spare Parts Kits by Component
M2922-64003 - Small Parts Kit
Table 10 M2922-64003 Small Parts Kit
Component Description Quantity
Screw, mach Phillips-head 4-40 X 3/16 4

Screw, tri-lob, Phillips-head 6 X 1/2 6
Ring retaining ext, 1/8 shaft 2
Screw, tri-lob, Phillips-head 4 X 3/8 17
Retaining ring for wheel 1
Screw locking kit 2

M2922-64001 - Housing Kit
Table 11 M2922-64001 Housing Kit
Small Parts Kit1 1
Front case 1
Louver cover plate 1
Handle 1
Rubber feet (cushions) 2
Speaker retainer spring 1
1. For contents of the Small Parts Kit, refer to Table 10 on page 66.

M2922-64002 - Speaker Kit
Table 12 M2922-64002 Monitor Speaker Kit
Small Parts Kit1 1
Speaker housing 1
Bracket R/A 4-40 1
Speaker retainer 1
Speaker 1
Cable - speaker assembly 1
Gasket - speaker 1
Pad - battery, front/rear 1
Label - rear 1
Pad - battery, front/rear 1
Pad - battery, right 1
Pad - battery, left 1
M2922-40003 - Battery Kit
Table 13 M2922-40003 Battery Kit
Small Parts Kit1 1
Battery, 6V 4AH lead acid, sealed 1


M3921-60406 - Knob (Navigation Wheel) Kit
Table 14 M2922-60406 Knob (Navigation Wheel) Kit
Knob 1
Ring retaining 3/8” shaft 1
M2922-44301 - Keypad Kit
Table 15 M2922-44301 Keypad Kit
Small Parts Kit1 1
Keypad - switch, membrane 1

1. For contents of the hardware mounting kit, refer to Table 10 on page 66.
M2922-64004 - Display Kit
Table 16 M2922-64004 Display Kit
Small Parts Kit1 1
LCD assembly 1
Window display with gasket 1

M2922-66505 - Side Connector PCB Kit
Table 17 M2922-66505 Side Connector PCB Kit
Small Parts Kit1 1
Side PCB, with twin ultrasound, and one Toco sockets 1

M2922-66510 - Interface PCB Kit
Table 18 M2922-66510 Interface PCB Kit
Small Parts Kit1 1
Interface PCB 1
M2922-66511 - Rear Connector PCB Kit
Table 19 M2922-66511 Rear Connector PCB Kit
Small Parts Kit1 1
Rear connector PCB 1


Assembly Drawings
Assembly Drawings
Figure 7 Assembly Drawing (Sheet 1) - Top Level Assembly

Assembly Drawings
Figure 8 Assembly Drawing (Sheet 2) - Front Case Assembly

Assembly Drawings
Figure 9 Assembly Drawing (Sheet 3) - Rear Case Assembly

Assembly Drawings
Figure 10 Assembly Drawing (Sheet 4) - Interface PCB/Rear

Connector PCB

Assembly Drawings
Figure 11 Assembly Drawing (Sheet 5) - Side Connector PCB/

Panel/Label

Assembly Drawings

8
Test and Inspection Matrix
Warnings
Warning
EXPLOSION HAZARD! Do not use the FM-2 in a flammable atmosphere
where concentrations of flammable anesthetics or other materials may
occur.
Warning
SHOCK HAZARD! The power-receptacle must be a three-wire grounded
outlet. A hospital grade outlet is required. Never adapt the three-prong plug
from the power supply or accessory to fit a two-slot outlet. If the outlet has
only two slots, make sure that it is replaced with a three-slot grounded
outlet before attempting to operate the monitor.
Warning
SHOCK HAZARD! Do not attempt to connect or disconnect a power cord
with wet hands. Make certain that your hands are clean and dry before
touching a power cord.
Warning
Use only patient cables and transducers supplied with the monitor. Use of
any other patient cables may result in out-of-specification performance and
possible safety hazards.
Chapter 8 - Test and Inspection Matrix 77

Cautions
Cautions
Caution
Use care when transporting or moving the monitor to assure that the
attached patient cables are stored so that they will not be damaged in the
move.
Caution
Keep the operating environment free of dust, vibrations, corrosive, or
flammable materials, and extremes of temperature and humidity. The unit
should be kept clean and free of transducer gel and other substances.
Caution
Do not operate the unit if it is damp or wet because of condensation or
spills. Avoid using the equipment immediately after moving it from a cold
environment to a warm, humid location.
Caution
Never use sharp or pointed objects to operate the front-panel switches.
78 Chapter 8 - Test and Inspection Matrix

Introduction
Caution
General-purpose personal computers and modems are not designed to
meet the electrical safety requirements of medical devices. The RS-232 and
parallel connectors on the monitor are electrically isolated to permit safe
connections to non-medical devices, which should be connected with a
cable of sufficient length to prevent the non-medical equipment from
contacting the patient.
If a non-medical device is connected to the serial port, a recorder or
printer connected at the same time to the parallel port should be located
outside the patient vicinity, as the two interfaces are not isolated against
each other.
Introduction
This chapter contains maintenance and safety information for the FM-2
antepartum fetal monitor and its accessories.
All checks that require the instrument to be opened must be made by qualified
service personnel. Please contact your local Agilent representative when you wish
safety and maintenance checks to be carried out.
To ensure that your monitor functions properly and safely, you must adhere to
the standards stated in this manual.

When to Perform Tests Blocks

Table 20 shows which test blocks to perform after repair and preventive
maintenance tasks.
Table 20 FM-2: When to Perform Test Blocks
Test Block(s) Required

Service Event
(See Table 21 on page 81)
The product is customer installed. Visual and Power On
Installation
Refer to the Instructions for Use.
Preventive maintenance is limited Power On

Maintenance
to exchanging the battery Safety Tests

Preventive
Unit Exchange Visual and Power On

Repairs
Unit opened Visual and Power On

Front End Connector Board Power On
exchanged Performance Tests for Trans-
ducers
Safety Tests
Rear Connector Board exchanged Power On
Safety Tests
Power Supply exchanged Power On
Battery exchanged Power On
Safety Tests

Table 21 Test and Inspection Matrix
Test Block What to

Test Expected Results
Name Record
Visual Test Inspect exterior of fetal No Visual Damage V:P or V:F

(See 20) monitor for damage.
Power-On Self- Power on the monitor Displays Normal Monitoring PO:P or PO:F
Test Screen Configuration and
(See 20) emits tones
Safety Tests:
• Safety Test 1 Enclosure Leakage All Safety Test results are in S:P or S:F
(See 86) Current - S.F.C. Open range of Table 22 on page 87
Supply
• Safety Test 2 Patient Leakage Cur- All Safety Test results are in S:P or S:F
(See 88) rent - S.F.C. Open range of Table 23 on page 89
Supply
Key to Table: P = Pass F = Fail

Battery Charging and Maintenance
Battery Charging and Maintenance

Before attempting to perform any tests, it is important to verify that the battery
is charged and functional.
Using the Battery

You can run the monitor for approximately six hours on battery power at room
temperature of 25o C from a fully charged battery (with a minimum of two
hours monitoring at 10o C from a fully charged battery). The age of the battery,
operating temperature and number of recharge cycles affects this. A battery life
cycle is approximately 200 charge/discharge cycles.
Low Power Warning

A low power warning occurs when the battery power is running low. The battery
fuel gauge flashes, and a repetitive audible tone sounds. Remaining monitoring
time is typically 30 minutes with a new battery at room temperature of 25o C. In
an older monitor, in which the battery has had a number of recharge cycles, it
may occur when fewer minutes remain.
The warning continues until the low power condition disappears (when you
connect the monitor to an AC power supply) or until the system stops
functioning because of the low power.You cannot silence it, and you cannot
adjust its volume.
The monitor retains any stored fetal traces, even if it shuts down because of lack
of battery power.

Preventive Maintenance
Recharging the Battery

Use the power supply to recharge the battery from an AC power source. This
takes a maximum of 14 hours when monitoring simultaneously, or eight hours if
no monitoring occurs. Typical times are 11 hours if you are monitoring
simultaneously, or 4.75 hours if no monitoring occurs.
Storing
A stored battery loses capacity over time. To minimize loss of capacity, recharge
the battery at least every six months. A battery typically has three to five years
shelf life.
Preventive Maintenance
The only preventive maintenance task required for the monitor is battery
exchange. Life expectancy of a battery depends on the frequency and duration of
use. The battery should be replaced every two years.
See “Removing the Battery” on page 43, and “Replacing the Battery” on page
44.

Safety Testing
Safety Testing
This section defines the test and inspection procedures applicable to the FM-2
fetal monitors. Use the tables in the following section to determine what test and
inspection results must be reported after a repair has been carried out.
• Test Blocks in Table 20 tells you when to carry out the tests blocks
• Test and Inspection Matrix in Table 21 tells you the expected results of the
tests and what to record.
Warning
Apply the safety test limits set by the local standards and statutes applicable
to the country of installation, such as IEC 601-1, UL2601, CAN/CSA-
C22.2 No. 601.1.M90.
The safety tests defined in this chapter are derived from local and
international standards but may not be equivalent. They are NOT a
substitute for local safety testing.
Caution
Successful completion of the patient safety tests does not ensure the correct
and accurate functioning of the equipment.

Safety Testing
Safety Test Procedures

The test procedures outlined in this section are to be used only for verifying the
safe installation or service of the product. “Safety checks at installation refer to
safety aspects directly related to the installation and setup activities and not to
intrinsic safety features that have already been checked during final acceptance
testing at the factory.”
[FDA 97-4179 Medical Quality Systems Manual: A Small Entity Compliance
Guide (QSR manual). First Edition December 1996. Chapter 14: Storage,
Distribution and Installation. This document may be viewed at http://
www.fda.gov.
When running safety tests on the peripheral components of the system, refer to
the documentation included with those products.
When performing safety tests, you must use a standard safety tester. You can use
testers complying with IEC 601-1 internationally. You may also use testers
complying with any local standards and statutes applicable to the country of the
installation. For safety test procedures see the operation instructions of the safety
tester used.
If using the Metron safety tester use your local regulations to perform the test,
for example
• in Europe: IEC60601-1/IEC60601-1-1
• in the US: UL2601-1
The Metron Report should print results as detailed in this chapter, along with
other data.
Note—For information and ordering guides for Metron products contact:

Metron AS, Travbaneveien 1, N-7044 Trondheim, Norway
Tel. (+47) 73 82 85 00; Fax (+47) 73 91 70 09;
E-mail: [email protected]/[email protected]
www: http://www.metron-biomed.com
There are two general categories of safety test:

• Ground integrity
• Electrical Leakage

Safety Testing
Ground Integrity
The FM-2 is a Class 2, Type BF instrument. It has an external power supply, and
is constructed with double insulation. The FM-2 does not require an isolated
Earth Ground terminal, neither is one installed. No Protective Ground
Continuity check is required.
Electrical Leakage
The following tests verify the electrical leakage of the monitor:
• Enclosure leakage Current
• Patient Leakage Current
Safety Test 1: Enclosure Leakage Current Test
Normal This test is applicable to Class 1 and 2 equipment, type B, BF, and CF Applied
Condition Parts. The test measures leakage current of exposed metal parts of the
Instrument Under Test. It tests both normal and reversed polarity.
For type BF and CF Applied Parts the test measures AP/GND.
Safety Test according IEC 601-1 (Clause 19).
Report the highest value.
Single Fault This test is applicable to Class 1 and 2 equipment, type B, BF, and CF Applied
Condition Parts. The test measures leakage current of exposed metal parts of the
(S.F.C.) Open Instrument Under Test with one supply lead interrupted. It tests both normal
Supply and reversed polarity.
For type BF and CF Applied Parts the test measures AP/GND.

Safety Testing
Test Steps 1. Connect the external power supply output cord to the monitor. Then
connect the appropriate external power supply input power cord to the
analyzer as recommended by the analyzer operating instructions.
2. Using the appropriate test cable, connect the analyzer to a fixing nut of
the RS-232 connector on the back of the monitor.
3. Turn the monitor on.
4. Perform the test as recommended by the analyzer operating instructions.
The analyzer leakage current indication must not exceed the values listed in
Table 22.
Table 22 Enclosure Leakage Current
Maximum Leakage Current

(µA)
Test Condition Polarity
AAMI/ANSI
IEC 601-1 ES1
Standard
Normal 100 µA 100 µA

Normal
Reversed 100 µA 100 µA
Normal 500 µA 300 µA
S.F.C.1 (Open Supply)
Reversed 500 µA 300 µA
1. S.F.C. = Single Fault Condition

Safety Testing
Safety Test 2: Patient Leakage Current Test
Normal This test is applicable to Class 1 and 2 equipment, type B, BF, and CF Applied
Condition Parts. The test measures patient leakage current from any individual patient
connection to earth (power ground) in parallel. It tests both normal and reversed
polarity.
Single Fault This test is applicable to Class 1 and 2 equipment, type B, BF, and CF Applied
Condition Parts. The test measures patient leakage current from any individual patient
(S.F.C.) Open connection to earth (power ground) in parallel, with one supply lead
Supply interrupted. It tests both normal and reversed polarity.
Test Steps This test requires a sample patient cable for each device parameter. These must
be configured as recommended by the safety analyzer operating instructions.
1. Configure the electrical safety analyzer as recommended by the analyzer
operating instructions.
2. Connect the appropriate external power supply input power cord to the
analyzer as recommended by the analyzer operating instructions. Connect
the external power supply output cord to the monitor.
3. Turn the monitor on.
4. Perform the test as recommended by the analyzer operating instructions.
For each test condition, the measured leakage current must not exceed that
indicated in Table 23.

Safety Testing
Table 23 Patient Leakage Current Values
Maximum Allowable
Leakage Current
Test Condition Polarity (µA)
Type B & BF
Normal 100 µA
Normal
Reversed 100 µA
Normal 500 µA
S.F.C.1 (Open Supply)
Reversed 500 µA
1. S.F.C. = Single Fault Condition
System Safety Test

Whenever you connect a monitor to an obstetrical system such as Agilent OB
TraceVue you must perform the System Test. The System Test consists of the
Enclosure Leakage Current tests (normal and single fault condition) as described
on 86. You must run this test when connecting either a new or repaired monitor.

Testing Transducers
Testing Transducers
Testing Toco Transducers
Visual Check Check the transducer for signs of damage. Ensure that there are no cracks in the
transducer housing or dome, in the cable or the connector plug.
Electrical 1. Turn on the monitor.

Check
2. Connect the transducer to the Toco socket.
3. Check that the display acknowledges the connected transducer in the

Toco frame of the main monitoring screen.
4. Lay the transducer face up on a flat surface for a few seconds.
5. Set the Toco Baseline as follows:
a. Highlight the Toco frame in the main monitoring screen by turning

the navigation wheel.
b. Press the wheel to enter the Toco Menu. The existing Toco Baseline
will be displayed.
c. If you need to change this, highlight the TOCO Baseline menu

item, and press the navigation wheel. You will see a box containing
the choices for setting the Toco Baseline.
d. Highlight the desired Toco Baseline value by turning the navigation

wheel, and select by pressing the wheel.
e. Exit the Toco menu by highlighting Return and pressing the

navigation wheel.
6. Zero the Toco by pressing the button.
7. Turn the transducer over so that button is face down on the flat surface.
Hold the cable at a point 25 cm from the transducer and ensure that the

Testing Transducers
transducer touches the flat surface only with the button and that the
transducer is parallel to the flat surface.
8. The Toco display should read between 20 and 40 units above the
Baseline.
Toco display = 5, 10, 15, or 20 Toco display = 20 - 40 Toco
depending on Baseline units above the Baseline
setting
Figure 12 Testing a Toco Transducer
9. If the test fails, repeat with another transducer. If it still fails, refer to
Chapter 5, “Troubleshooting”.

Testing Transducers
Testing Ultrasound Transducers
Visual Check Check the transducer for signs of damage. Ensure that there are no cracks in the
transducer housing or dome, in the cable or the connector plug.
Electrical 1. Turn on the monitor.

Check
2. Connect the transducer(s) to the US 1 or US 2 socket.
3. Check that the display acknowledges the connected transducer(s) in the

Ultrasound frame of the main monitoring screen.
4. Increase the loudspeaker volume to an audible level.
5. Holding the transducer in one hand, move your hand repeatedly towards
and then away from the surface of the transducer, or gently tap the
transducer surface with your finger.
Figure 13 Testing an Ultrasound Transducer
6. Check that a noise is heard from the loudspeaker.

Testing Transducers
7. The transducer contains seven piezo-electric crystals.
Figure 14 Position Of Crystals in an Ultrasound Transducer
8. Holding the transducer in one hand, move a flat-bottomed pencil or

similar object repeatedly towards and then away from each crystal. The
distance between the pen and the transducer surface should be about 2 to
3 cm.
Figure 15 Testing the Crystals in an Ultrasound Transducer
9. Check that a noise is heard from the loudspeaker for each crystal.

Testing Transducers
10. If the test fails, repeat using another transducer. If it still fails, refer to
Chapter 5, “Troubleshooting”.

Index
A D not self-detected, 22
self-detected, 22
A/D values, 27, 29 demo mode, 27 exchange
accessory testing disassembly monitor, 2
transducers, 22 of major parts, 38 exploded parts diagrams, 71
Toco, 90 tools, 39
US, 92 disassembly procedures, 37–61
assembly drawings, 71 closed case, 40–44 F
battery, 43
speaker housing, 41 foot cushions
B speaker wires removal, 58
disconnection, 41 front case assembly, 38
battery disassembly. See disassembly
front case, 47
charging time, 83 procedures
keypad, 54
checking, 20 separation from rear, 45
LCD assembly, 50
disposal, 44 fuses, 39
main PCB, 49
importance of polarity, 44
navigation wheel, 47
observing polarity, 43
main PCB, 59
recharging, 83 G
side connector PCB, 59
removal, 43
side panel, 59 general information, 1
removal/replacement
rear case ground integrity, 85
precautions, 40
foot cushions, 58
replacement, 44
handle, 58
storing, 83
interface board, 55 H
using, 82
rear connector PCB, 55
block diagram handle
tools required, 39
of operation, 7 removal, 58
display
removal, 50 housing kit, 67
C replacement, 51
window removal, 51 I
cables
null-modem, 14 icon
parallel printer, 18 E indoor use only, 4
recorder, 18 paper advance, 4
electrical leakage, 85
cautions, 3 power supply input
enclosure leakage current, 81,
cleaning, 11 power supply input icon, 4
87
closed case disassembly. See power supply output, 4
error codes, 23
disassembly procedures power-on indicator, 4
8 most recent, 28
communications ports printing enable/disable, 4
explanation, 23
parallel, 8 IEC601-1, 85
error log, 19, 27, 28
serial I/O, 8 IEEE-1284
screen, 28
crystals compliant cable, 18
errors, 19
in US transducer, 93 indoor use only icon, 4
handling, 22
initialization string
Index 95
attention characters (AT), 15 M placement, 14, 18
default entries, 16 notes, 3
&K0, 16 main PCB null-modem
E0, 16 disassembly procedures, 59 cable, 14
X0, 16 removing from front case
X4, 16 assembly, 49
modem replacing, 52 O
default, 15 malfunction categories
degraded operation, 32 OB TraceVue
user-customizable, 15
totally inoperative, 32 and system safety test, 89
return characters, 15
measurement channels, 10 RS-232 interface, 13
installation, 6
Metron overview
mountings, 10
contact address, 85 of monitor, 6
intended readership, 2
prerequisites, 2 safety tester, 85
interface modem
P
parallel, 13 default initialization string, 15
serial, 13 validated, 17 packing
interface board 6210GSM, 17 and warranty, 5
removal, 55 MultiTech MT-5600ZDX, 15 for shipment, 5
interface PCB Nokia 6210GSM, 15 general instructions, 5
removal modems repacking
from rear conn. PCB, 56 supported, 14 in different carton, 5
replacing monitor in original carton, 5
on rear connector PCB, 56 block diagram, 7 paper advance icon, 4
exchanging, 2 parallel interface, 13, 18
general description, 6 PCL level 3 printer, 18
K main assemblies. See front parallel port
and rear case assembly PCL printer, 8
keypad major component parts, 38 patient leakage current, 81, 88
description, 9 mechanical description, 8 values, 89
removal, 54 overview of, 6 PCL Level 3
replacement, 54 mountings validated printers, 18
roll stand, 10 performance assurance tests
wall-mount, 10 power-on self-test, 19
L
MultiTech, 15 transducer testing, 19, 22
LCD MultiTech MT-5600ZDX, 17 visual test, 20
assembly pinouts
high voltage precautions, 50 RS-232 interface, 14
replacing, 51 N serial interface, 14
assembly removal, 50 navigation wheel placement
backlight, 8 description, 9 non-medical equipment, 14, 18
display, 8 removal, 47 power
resolution, 8 replacing, 48 low, warning of, 82
LCD display Nokia 6210GSM, 15, 17 power supplies, 9
window removal, 51 non-medical equipment power supply output icon, 4
96 Index
power-on indicator icon, 4 rear connector PCB S
power-on jingle, 21 removal, 55
power-on self-test, 2, 19, 20, 81 removing interface board safety tester, 85
checksum, 20 from, 56 safety testing, 84
error and error detection, 21 replacing interface PCB on, 56 safety tests, 2, 19, 81
explanation, 20 reassembly procedures, 37–61 categories, 85
jingle, 21 closed case electrical leakage, 85
performing, 21 battery, 44 enclosure leakage current, 81,
watchdog timer, 21 speaker housing, 42 86
power-up defaults, 25–29 front and rear case, 46 normal condition, 86
alarm settings, 25 front case single fault condition, 86
data transfer, 26 keypad, 54 ground integrity, 85
destination, 26 LCD assembly, 51 limits, 84
date, 26 main PCB, 52 local regulations, 85
format, 26 navigation wheel, 48 Metron safety tester, 85
explanation, 25 main PCB patient leakage current, 81
language, 26 side connector PCB, 61 normal condition, 88
modem init string, 25 side panel, 61 single fault condition, 88
patient ID, 26 rear case procedures, 85
phone number, 25 rear connector/interface safety tester, 85
recorder paper PCB assembly, 57 standards, 84
speed, 26 recorder system safety test, 19
recorder paper style, 26 cable, 18 test 1, 81
settings, 25 repair strategy, 1, 2 test 2, 81
time format, 26 FM-2 Recorder, 1 test blocks, 19
Toco baseline set-point, 25 repairs screwdriver
US trace separation, 25 battery exchanged, 80 Phillips-head, 39
prerequisites for readers, 2 front end connector board serial interface, 13
preventive maintenance exchanged, 80 pinouts, 14
battery exchange, 80, 83 power supply exchanged, 80 to PC/AT computer, 13
printers rear connector board service
supported PCL Level 3, 18 exchanged, 80 by qualified service
supported PCL level 3, 18 unit exchange, 80 personnel, 79
validated, 18 unit opened, 80 philosophy, 19
printing enable/disable roll stand, 10 service menu, 26
icon, 4 routine maintenance, 11 accessing, 26
RS-232 interface, 13 error log, 27, 28
modem explanation of entries, 27
R desktop, 13 function, 27
GSM cell phone, 13 purpose, 26
rear case assembly, 38 purpose of, 26
OB TraceVue, 13
description, 39 system A/D values, 27
pinouts, 14
disassembly. See disassembly service tests
procedures overview, 19
separation from front, 45 shipment
Index 97
packing for, 5 screen, 29 crystals, 93
side connector PCB system interfaces, 13–18 troubleshooting, 31–36
removal, 59 parallel, 18 initial daignosis, 32
side panel system safety test, 89 overview, 31
removal, 59
small parts kit, 63
software upgrades T U
RS-232 interface, 13
test and inspection matrix, 19, UL2601-1, 85
spare parts, 63–??
77–94 ultrasound
assembly drawings, 71
expected results, 81 sockets, 10
exchange assemblies
introduction, 79 US 1, 10
M2922A, 64
reporting, 81 US 2, 10
M2925A, 64
test blocks ultrasound channel, 10
exchange parts, 64
power-on self-test, 81 US trace separation
M2922-40003
safety tests, 81 power-up defaults, 25
battery kit, 68
visual test, 81
M2922-44301
when to perform, 80
keypad kit, 69 V
testing
M2922-60406
after repair, 2
navigation wheel kit, 69 validated modems, 15
tests and error codes, 19–??
M2922-64001 validated printers, 18
Toco baseline set-point
housing kit, 67 visual test, 19, 81
power-up defaults, 25
M2922-64002
Toco channel, 10
speaker kit, 68
Wheatstone bridge, 10 W
M2922-64004
tools
display kit, 69 wall-mount, 10
10 mm hex socket
M2922-66505 watchdog timer, 21
for encoder nut, 47
side connector PCB kit, 70
for disassembly, 39
M2922-66510
9/16-inch socket, 39
interface PCB kit, 70
needle-nose pliers, 39
M2922-66511
Phillips-head
rear connector PCB kit, 70
screwdriver, 39
non-exchange assemblies
torque settings
M2922A, 65
encoder switch nut, 48
small parts kit, 63, 66
rear to front case screws, 46
supplies and accessories
speaker housing screws, 42
M2922A, 66
transducer
speaker housing
performance test, 22
removal, 41
transducer testing, 22
replacement, 42
toco
support strategy, 19
electrical check, 90
supported modems, 14
visual check, 90
symbols and definitions, 5
ultrasound, 92
system A/D values, 29
US
overview, 29
98 Index

Antepartum Fetal Monitor

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Antepartum Fetal Monitor

Uploaded by

Copyright:

Available Formats

FM-2 (M2922A)

Antepartum Fetal Monitor

Philips Medizinsyteme Boeblingen GmbH

Microsoft® is a U.S. registered trademark of Microsoft Corp.

Conventions Used in This Guide

Note— A note calls your attention to an important point in the text.

4. Power-up Default Settings and the Service Menu . . . . . . . . 25

8. Test and Inspection Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Table 1 Fully wired DB9 RS-232 Null-modem pinouts . . . . . . . . . . . . . . . . . .14

Figure 1 FM-2 Block Diagram of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 1 - General Information 1

Who Should Read This Guide

2 Chapter 1 - General Information

Warnings, Cautions, and Notes

Note—A note calls your attention to an important point in the text.

On your monitor, this sign indicates that there is

Chapter 1 - General Information 3

Symbols and Definitions

Symbol Definition Symbol Definition

Drip-proof equipment Type BF applied part

Power input symbol on Refer to accompanying

Power supply connector RS-232 connector (symbol

Power supply output RS-232 connector (symbol

Functional earth symbol on Printer connection symbol

Indoor use only symbol

4 Chapter 1 - General Information

Packing for Shipment

Repacking in Original Carton

Repacking in a Different Carton

Chapter 1 - General Information 5

Overview Of The Device

6 Chapter 1 - General Information

Block Diagram of Operation

Figure 1 FM-2 Block Diagram of Operation

Chapter 1 - General Information 7

LCD and Backlight

Serial I/O Communications Port

Parallel I/O Communications Port

8 Chapter 1 - General Information

with the monitor, please see “Parallel I/O Communications Interface” on

Keypad and Navigation Wheel

Chapter 1 - General Information 9

10 Chapter 1 - General Information

Routine Maintenance and Cleaning

Chapter 1 - General Information 11

12 Chapter 1 - General Information

The monitor has the following system interfaces:

Serial I/O Communications Interface

Chapter 2 - System Interfaces 13

Table 1 Fully wired DB9 RS-232 Null-modem pinouts

1 and 6 4 DTR Data Terminal Ready

The cable (M1380-61624) is a 3 meter long, fully wired RS-232 Null-modem

Note—As modems are not designed to fulfil the electrical requirements of a

14 Chapter 2 - System Interfaces

• a MultiTech Systems MT-5600ZDX desktop modem

MultiTech Systems MT-5600ZDX

Chapter 2 - System Interfaces 15

cm JANE DOE 194848

The components of the default initialization string are explained in the

Table 2 MultiTech MT-5600ZDX initialization string

E0 Switches to verbose mode. To establish whether a modem

16 Chapter 2 - System Interfaces

The commands above are only applicable to Rockwell/Conexant-based

Chapter 2 - System Interfaces 17