TBEN-L - SE-M2: 10-Port Ethernet Switch
TBEN-L - SE-M2: 10-Port Ethernet Switch
TBEN-L…-SE-M2
10-Port Ethernet Switch
Instructions for Use
2 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
Table of Contents
1 About These Instructions .................................................................................................................. 5
1.1 Target groups................................................................................................................... 5
1.2 Explanation of symbols used ........................................................................................ 5
1.3 Additional documents.................................................................................................... 5
1.4 Feedback about these instructions.............................................................................. 5
2 Notes on the Product ......................................................................................................................... 6
2.1 Product identification..................................................................................................... 6
2.2 Scope of delivery ............................................................................................................. 6
2.3 Legal requirements......................................................................................................... 6
2.4 Turck service..................................................................................................................... 6
3 For Your Safety.................................................................................................................................... 7
3.1 Intended use..................................................................................................................... 7
3.2 General safety notes ....................................................................................................... 7
3.3 Notes on UL approval ..................................................................................................... 7
3.4 Notes on Ex protection................................................................................................... 7
3.5 ATEX and IECEx approval requirements for use in Ex area ..................................... 8
4 Product Description ........................................................................................................................... 9
4.1 Device overview .............................................................................................................. 9
4.1.1 Operating elements ...................................................................................................................... 10
4.1.2 Display elements............................................................................................................................ 10
4.2 Properties and features................................................................................................ 10
4.3 Operating principle....................................................................................................... 10
4.4 Functions and operating modes ................................................................................ 11
4.4.1 SNMP agent...................................................................................................................................... 11
4.4.2 Neighborhood detection via LLDP (Link Layer Discovery Protocol) ........................... 11
4.4.3 Prioritization/classification of data packets via QoS ......................................................... 11
4.4.4 DHCP................................................................................................................................................... 11
4.4.5 Network redundancy.................................................................................................................... 11
4.4.6 Routing .............................................................................................................................................. 12
4.4.7 Firewall............................................................................................................................................... 12
4.4.8 NAT (Network Address Translation) ........................................................................................ 12
4.4.9 Mirroring – mirroring switch ports .......................................................................................... 12
4.4.10 IGMP (Internet Group Management Protocol).................................................................... 12
5 Installing............................................................................................................................................. 13
5.1 Installing the device in Zone 2 and Zone 22 ............................................................ 13
5.2 Mounting onto a mounting plate .............................................................................. 14
5.3 Mounting the device outdoors................................................................................... 14
5.4 Grounding the device................................................................................................... 15
5.4.1 Equivalent wiring diagram and shielding concept ........................................................... 15
5.4.2 Shielding the Ethernet ports...................................................................................................... 16
5.4.3 Grounding the device .................................................................................................................. 16
6 Connecting ........................................................................................................................................ 17
6.1 Connecting the device in Zone 2 and Zone 22 ........................................................ 17
6.2 Connecting network segments .................................................................................. 17
6.3 Connecting the power supply .................................................................................... 19
V02.00 | 2021/11 3
Table of Contents
4 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
1 About These Instructions
These instructions for use describe the structure, functions and the use of the product and will
help you to operate the product as intended. Read these instructions carefully before using the
product. This is to avoid possible damage to persons, property or the device. Retain the instruc-
tions for future use during the service life of the product. If the product is passed on, pass on
these instructions as well.
V02.00 | 2021/11 5
Notes on the Product
Turck service
6 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
3 For Your Safety
The product is designed according to state-of-the-art technology. However, residual risks still
exist. Observe the following warnings and safety notices to prevent damage to persons and
property. Turck accepts no liability for damage caused by failure to observe these warning and
safety notices.
V02.00 | 2021/11 7
For Your Safety
ATEX and IECEx approval requirements for use in Ex area
8 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
4 Product Description
The devices are designed in a fully encapsulated housing with degree of protection IP65/IP67/
IP69K.
Der TBEN-L…-SE-M2 is a 10-port Ethernet switch. The switch has two 8-pin, X coded M12 Gig-
abit Ethernet ports (XF9 and XF10) with a transmission speed of 10/100/1000 Mbps and eight 4-
pin, D coded M12 Fast Ethernet ports (XF1…XF8) with a transmission speed of 10/100 Mbps.
For connecting the supply voltage, 4-pin (TBEN-L4) 7/8'' connectors, 5-pin (TBEN-L5) 7/8''
connectors or 5-pin M12 connectors (TBEN-LL) are available.
green
Ø 6.3 [0.25]
XF9 XF4 XF3 XF2 XF1 XD1
60.4 [2.38]
green
Ø 6.3 [0.25]
XF9 XF4 XF3 XF2 XF1 XD1
60.4 [2.38]
V02.00 | 2021/11 9
Product Description
Operating principle
green
Ø 6.3 [0.25]
XF9 XF4 XF3 XF2 XF1 XD1
60.4 [2.38]
10 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
4.4 Functions and operating modes
4.4.1 SNMP agent
The switch supports SNMP (Simple Network Management Protocol) V1, V2c and V3. The SNMP
function of the device can be configured via the web server.
4.4.4 DHCP
The switch supports the following DHCP options:
n DHCP server
n DHCP client
n DHCP server option 82, port-based IP address assignment
V02.00 | 2021/11 11
Product Description
Functions and operating modes
4.4.6 Routing
Routing is used to forward data packets between networks with different IP address ranges.
Several routing rules can be defined in the switch for data transfer between the configurable
LAN and WAN network zones.
NOTE
IP forwarding (forwarding of data packets between networks with different IP ad-
dress ranges) must be activated.
4.4.7 Firewall
The switch firewall offers the possibility to set up rules for incoming and outgoing data packets
as well as forwarding rules for data packets. The rules can be defined network-wide or IP-ad-
dress-based and apply to all data packets or only to UDP-based or TCP-based packets.
12 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
5 Installing
5.1 Installing the device in Zone 2 and Zone 22
In Zone 2 and Zone 22, the devices can be used in conjunction with the protective housing set .
DANGER
Potentially explosive atmosphere
Risk of explosion through spark ignition
For use in Zone 2 and Zone 22:
Only install the device if there is no potentially explosive atmosphere present.
Observe requirements for Ex approval.
V02.00 | 2021/11 13
Mounting
Mounting the device outdoors
NOTICE
Mounting on uneven surfaces
Device damage due to stresses in the housing
Fix the device on a flat mounting surface.
Use two M6 screws to mount the device.
M6 (2x)
max. 1.5 Nm
218 [5.58]
14 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
5.4 Grounding the device
5.4.1 Equivalent wiring diagram and shielding concept
2 x 15 nF 2 x 15 nF
XF2 XF6 XF2 XF6
Fig. 6: TBEN-L4-SE-M2– equivalent wiring dia- Fig. 7: TBEN-L5-SE-M2– equivalent wiring dia-
gram and shielding concept gram and shielding concept
XD1 XD2
XF1 XF5
2 x 15 nF
XF2 XF6
XF3 XF7
XF4 XF8
XF9 XF10
V02.00 | 2021/11 15
Mounting
Grounding the device
1
2
The grounding ring (1) is the module grounding. The shielding of the Ethernet ports is perman-
ently connected to the module grounding. The module grounding is only connected to the ref-
erence potential of the installation when the module is mounted.
In the device variants TBEN-L5-SE-M2 and TBEN-LL-SE-M2, the earthing can also be connected
via pin 5 of the connector for the supply voltage.
16 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
6 Connecting
The TBEN-L…-SE-M2 is only suitable for use in LAN networks.
NOTICE
Intrusion of liquids or foreign bodies through leaking connections
Loss of protection class IP65/IP67/IP69K, device damage possible
Tighten M12 connectors with a tightening torque of 0.6 Nm.
Tighten 7/8” connectors with a tightening torque of 0.8 Nm.
Only use accessories that guarantee the protection class.
Always seal unused connectors with suitable screw caps or blind caps. The tight-
ening torque for the screw caps is 0.5 Nm.
DANGER
Potentially explosive atmosphere
Risk of explosion through spark ignition
When used in Zone 2 and Zone 22:
Only disconnect and connect circuits when no voltage is applied.
Only use connecting cables that are approved for use in potentially explosive at-
mospheres.
Use all connectors or seal them with blind plugs.
Observe requirements for Ex approval.
1 = TxD1 +
v 2 = TxD1 –
7 8 3 = RxD2 +
6 1 4 = RxD2 –
5 = BID4 +
5 2 6 = BID4 –
4 3 7 = BID3 +
XF9, XF10 8 = BID3 –
flange = FE
V02.00 | 2021/11 17
Connecting
Connecting network segments
v
2 1 = TX +
2 = RX +
1 3 3 = TX –
4 4 = RX –
flange = FE
XF1…XF8
18 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
6.3 Connecting the power supply
TBEN-L4-SE-M2/TBEN-L5-SE-M2
For the connection to the power supply, the device has two 5-pin 7/8” connectors. The power
supply connectors are designed as 4-pin (TBEN-L4) or 5-pin (TBEN-L5) 7/8" connectors. V1 and
V2 are galvanically isolated. The maximum tightening torque is 0.8 Nm.
Connect the device to the power supply according to the pin assignment shown below.
w v w v
3 1 BK = GND V2 3
1 RD = 24 VDC V2
1 3 2 GN = 24 VDC V1 3 1 4 2 2 BU = GND V1 2 4
3 GNYE = FE
2 4 3 WH = GND V1 4 2 5 1 4 BN = 24 VDC V1 1 5
4 BK = GND V2 5 WH = 24 VDC V2
X1 X2 X1 X2
Connector Function
X1 Power feed
X2 Continuation of the power to the next node
Voltage Function
V1 System voltage: power supply 1 (incl. supply of electronics)
V2 Load voltage: power supply 2, fed through, not used in device
V02.00 | 2021/11 19
Connecting
Connecting the power supply
TBEN-LL-SE-M2
For the connection to the supply voltage, the device has two 5-pin, L coded M12 connectors.
V1 and V2 are galvanically isolated. The maximum tightening torque is 0.6 Nm.
Connect the device to the power supply according to the pin assignment shown below.
Always seal unused connectors with suitable screw caps or blind caps. The tightening
torque for the screw caps is 0.5 Nm.
1 = 24VDC V1
FE FE
2 = GND V2
1 4 4 1
3 = GND V1
2 3 4 = 24VDC V2 3 2
FE
XD1 XD2
Connector Function
XD1 Power feed
XD2 Continuation of the power to the next node
Voltage Function
V1 System voltage: power supply 1 (incl. supply of electronics)
V2 Load voltage: power supply 2, fed through, not used in device
20 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
6.3.1 Supply concept
The device is supplied via V1. All Ethernet ports are galvanically isolated. V2 is fed through.
V1 V1
V2 V2
V2
V02.00 | 2021/11 21
Commissioning
Opening the web server
7 Commissioning
7.1 Opening the web server
The web server can be opened via a web browser or via the Turck Service Tool. Calling the web
server via the Turck Service Tool is described in the section ”Setting the Network address”.
NOTE
The password is transmitted in plain text for HTTP connections. The password is only
encrypted if access to the web server is established via an HTTPS connection.
NOTICE
Inadequately secured devices
Unauthorized access to sensitive data
Change password after first login. Turck recommends using a secure password.
Adapt the password to the requirements of the network security concept of the
system in which the devices are installed.
22 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
7.2 Adjusting network settings
The network settings for the LAN network zone of the switch can be set via two decimal rotary
coding switches and DIP switches on the device, via the web server or via the Turck Service
Tool.
The network settings for the WAN network zone on the switch can only be set via the web
server.
x 10
7 8
6 9
5 0
4 1 3 2 1 Set
3 2
SRV
8
67 9 ON
5 0
4 1
3 2 x1 USB Host
V02.00 | 2021/11 23
Commissioning
Adjusting network settings
Switch positions
The network settings of the device depend on the selected mode. Changes to the settings be-
come active after a voltage reset.
Switch position
DIP switch [MODE] Rotary cod- Setting option Description
ing switches
0 00 Network reset The network reset resets the following network settings to the
default values:
IP address: 192.168.1.100
Subnet mask: 255.255.255.0
Gateway: 192.168.1.1
0 1…99 Rotary In rotary mode (static rotary), the last byte of the IP address can
be set manually at the device. The other network settings are
stored non-volatile in the memory of the device and cannot be
changed in rotary mode. Addresses from 1...99 can be set.
1 40 DHCP In DHCP mode, the network settings are by a DHCP server in
the network. The subnet mask assigned by the DHCP server
and the default gateway address are stored non-volatile in the
memory of the device. DHCP supports three mechanisms for IP
address allocation:
n Automatic address assignment: The DHCP server assigns a
permanent IP address to the client.
n Dynamic address assignment: The IP address assigned by
the server is only reserved for a certain period of time. After
this time has elapsed or after the explicit release by a client,
the IP address is reassigned.
n Manual address assignment: A network administrator as-
signs an IP address to the client. In this case, DHCP is only
used to transmit the assigned IP address to the client.
n Default IP address: 192.168.1.254
1 50 PGM In PGM mode, the network settings are assigned manually via
the Turck Service Tool, FDT/DTM or via a web server. The set-
ting are stored to non-volatile the device.
n Default IP address: 192.168.1.254
1 60 PGM-DHCP In PGM DHCP mode, the device initially operates a DHCP client
and sends DHCP requests until it is assigned a permanent IP
address. The DHCP client is automatically deactivated as soon
as the device has received an IP address via the DTM, the or the
web server.
n Default IP address: 192.168.1.254
1 90 Factory reset The factory(F_Reset) all settings to the default values:
n Network setting (IP address, subnet mask, gateway)
n Device parameters
1 00 Restore Enter the device name and the device's IP address.
n IP address: 192.168.1.254
24 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
7.2.2 Adjusting network setting via Turck Service Tool
NOTE
The IP address can only be assigned using the Turck Service Tool if the switch is con-
nected to the PC via one of its LAN ports. Connection to a WAN port is not possible.
V02.00 | 2021/11 25
Commissioning
Adjusting network settings
NOTE
Clicking the device's IP address opens the web server.
NOTE
An IP address assigned vie the Turck Service Tool is not stored permanently in the
switch.
26 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
7.2.3 Adjusting network settings via the web server
NOTE
To be able to adjust the network settings via the web server, the device must be in
PGM mode.
V02.00 | 2021/11 27
Commissioning
User management and rights assignment
NOTICE
Inadequately secured devices
Unauthorized access to sensitive data
Change password after first login. Turck recommends using a secure password.
Adapt the password to the requirements of the network security concept of the
system in which the devices are installed.
The password is transmitted in plain text for HTTP connections. The password is only encrypted
if access to the web server is established via an HTTPS connection.
In the delivery state or after a factory reset, the default settings are as follows:
n User: admin
n Password: password
28 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
7.3.2 Adding a user
ü The logged in user is a user with admin rights (area permission level 0).
Assign a user name and an initial password for the new user under Maintenance Ò
Users Ò Users.
Select the authorization level and create the new user via Add user.
NOTICE
Inadequately secured devices
Unauthorized access to sensitive data
Change password after first login. Turck recommends using a secure password.
Adapt the password to the requirements of the network security concept of the
system in which the devices are installed.
V02.00 | 2021/11 29
Setting
Configuring device functions with the web server
NOTE
Changes to the configuration of the device are stored non-fail-safe in the device. Un-
saved configuration changes are displayed via the Nonpersistant Configuration ad-
dition on the web server interface. In order to store a changed configuration fail-
safe, it must be saved via Configuration (changed) Ò Make current configuration
persistent [} 55].
Interface Settings
30 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
Make settings on ports XF1...XF10 and accept changes with SET.
Setting Value Meaning
XFn 1…10 Number of the Ethernet port
Name Freely selectable name
Port Enable Port activated
Disable Port deactivated
AutoNeg On Autonegotiation activated
Off Autonegotiation deactivated
Speed 10 Setting the transmission rate These settings can
100 of the Ethernet port only be configured if
autonegotiation is dis-
1000 (only valid for XF9
abled.
and XF10)
Duplex Full Setting the data transfer
Half
MDIx On Auto MDIx activated
Off Auto MDIx deactivated
Switching
Function Meaning
Broadcast Storm Protection Reduces the forwarding of broadcast messages.
The function should only be activated if problems
occur due to broadcast storms. In PROFINET applic-
ations, relevant PROFINET frames may be sup-
pressed if Broadcast Storm Protection is activated.
Flood unknown Multicasts/ On Activates the forwarding of multicast or unicast
Unicasts telegrams to all ports. The function must be activ-
ated for PROFINET applications.
Off Deactivates the forwarding of multicast or unicast
telegrams.
IGMP only Activates the reception of IGMP telegrams, other
multicast or unicast telegrams are not received.
V02.00 | 2021/11 31
Setting
Configuring device functions with the web server
8.1.3 LAN – WAN – VLAN – coding switches and VLAN configuring network zones
Zones
In the Zones area, the Ethernet ports of the switch are assigned to the LAN or WAN network
zones. If ports are assigned to the WAN, an IP address for the WAN must be assigned under IP.
Assign the zones and write them to the device via SET ZONES.
Set the IP address for the WAN as described in the under ”Setting the IP Address via the
web server” [} 27].
32 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
VLAN Interface Settings
Under VLAN Interface Settings area, the Ethernet ports are assigned to the previously defined
VLANs.
Assign the VLAN ID and name if necessary and create them via ADD ID.
Set the VLAN tag on the Ethernet port to enabled and enter the VLAN ID under Default
VLAN ID to make the assignment.
Fig. 32: Web Server - defining VLAN IDs and assigning Ethernet ports
V02.00 | 2021/11 33
Setting
Configuring device functions with the web server
Under VLAN ID/Interface Mapping, define how the switch port is handled in the VLAN.
Option Description
Not a member The port is not assigned to a VLAN.
Untagged The port is an untagged member of the VLAN. Forwarded packets are
untagged. The VLAN is port-based, which means one VLAN can be set
per switch port.
Tagged The port is a tagged member of the VLAN. All packets forwarded by
the interface are tagged. The packets contain VLAN information.
Tagged VLANs allow multiple VLANs to be used on one switch port.
34 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
8.1.4 SNMP – setting up SNMP
SNMP configuration
In the section SNMP Configuration the supported SNMP versions as well as the read and write
communities for authentication with SNMP V1 and SNMP V2c are configured.
Configure and transfer settings to the device with SET.
SNMP User
The SNMP User section contains a list of all users created under Add User for SNMP version 3.
REMOVE is used to delete created SNMP users.
Add User
In the section Add User, SNMP users are created for the authentication of devices with
SNMP V3.
Assign user name (User Name) and passwords.
Add user via ADD USER.
V02.00 | 2021/11 35
Setting
Configuring device functions with the web server
Traps
SNMP traps are a standard for error and change notifications in network management. If a
device detects an error or change, it sends a notification to one or more trap recipients, a trap
community.
The switch sends traps on the following events:
Trap Description
Link up A new connection is established, a device is connected to one of the
ports.
Link down The connection to a connected device is interrupted.
Reboot The switch is restarted.
Under Destination, specify the IP address of the device on the network that is to receive
the traps.
Under Community, specify the community to which the traps are to be sent.
Send the configuration to the device via SET.
36 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
8.1.5 DHCP – setting up a DHCP server
V02.00 | 2021/11 37
Setting
Configuring device functions with the web server
Static Leases
In the section Static Leases, devices can be defined for which a static IP address is to be
assigned independently of the lease time. Static addresses are permanently stored. They are
not deleted after the Aging Time has expired or when the switch is restarted.
Enter the IP address that is to be permanently assigned. This IP address must be beyond
the previously defined IP address range.
Enter the MAC address of the device that will be permanently assigned this IP address.
38 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
Interface-based IP Assignment
In the section Interface-based IP Assignment, Ethernet port-dependent IP addresses can be
assigned. The IP addresses are assigned independently of the device for the first connected
device that sends a DHCP request. If further devices are connected to the port, these devices
receive an IP address from the DHCP address pool.
Enter IP addresses at the respective port.
Send the configuration to the device via SET.
Active Leases
The section Active Leases contains a list of devices that have already been assigned an IP
address via DHCP.
V02.00 | 2021/11 39
Setting
Configuring device functions with the web server
40 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
8.1.7 QoS – prioritizing or classifying data packets
Interface Settings
In the section Interface Settings the prioritization or classification of data packets can be set
port by port.
The default setting are written in bold.
Function Value Meaning
XFn 1…10
Prio Choice Default Telegrams are processed according to default prioritiz-
ation or default classification.
PCP > default Telegrams that have been prioritized via PCP are al-
ways processed first.
DSCP > default Telegrams that have been prioritized via DSCP are al-
ways processed first.
PCP > DSCP > default Telegrams that have been prioritized via PCP are al-
ways processed first. This is followed by the pro-
cessing of telegrams that have been classified via
DSCP. All other telegrams are then processed
Default Queue Q0 (weighted, 1×) Queue 0: the data is processed with a weighting of 1.
Q1 (weighted, 2×) Queue 1: the data is processed with a weighting of 2.
Q2 (weighted, 3×) Queue 2: the data is processed with a weighting of 3.
Q3 (weighted, 6×) Queue 3: the data is processed with a weighting of 6.
Q4 (weighted, 12×) Queue 4: the data is processed with a weighting of 12.
Q5 (3rd, strict) Queue 5: Strict priority (3)
Q6 (2nd, strict) Queue 6: Strict priority (2)
Q7 (1st, strict) Queue 7: Strict priority (1)
Default PCP Prioritization level according to IEEE 802.1, the prioritization according to
PCPs is part of the VLAN tagging.
0 Lowest priority, for background processes the process
1 Best effort
2 Excellent effort
3 Critical applications
4 Video, < 100 ms delay
5 Voice, < 10 ms delay
6 Internetwork control
7 Highest priority, network control
V02.00 | 2021/11 41
Setting
Configuring device functions with the web server
42 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
PCP Ò Queue Mapping
The section PCP Ò Queue Mapping defines to which output queues telegrams are assigned
based on their PCP priorities.
Default-settings:
PCP Value Transmit Queue PCP Value Transmit Queue
0 Q1 (weighted, 2×) 4 Q4 (weighted, 12×)
1 Q0 (weighted, 1×) 5 Q5 (3rd, strict)
2 Q2 (weighted, 3×) 6 Q6 (2nd, strict)
3 Q3 (weighted, 6×) 7 Q7 (1st, strict)
V02.00 | 2021/11 43
Setting
Configuring device functions with the web server
44 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
DSCP Ò PCP Mapping
In the section DSCP Ò PCP Mapping, the DSCP entries are assigned to PCP priorities. In the
following example, telegrams that were classified via a DSCP of 5 received the highest
priority (7).
Default settings:
DSCP Value Transmit Queue DSCP Value Transmit Queue
0…7 0 21…39 4
8…15 1 40…47 5
16…23 2 48…55 6
24…31 3 56…63 7
V02.00 | 2021/11 45
Setting
Configuring device functions with the web server
46 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
8.1.9 Redundancy – configuring network redundancy
(R)STP Variant
The section (R)STP Variant defines which network redundancy protocol [} 11] is used in the
network zones LAN, WAN, LAN-VLAN and WAN-VLAN.
Select the network redundancy protocol.
Send the configuration to the device via SET.
NOTE
IP forwarding (forwarding of data packets between networks with different IP
address ranges) must be activated.
Add Route
Example:
Telegrams from station 1 at port 2 of the switch will be forwarded to station 2 of another net-
work.
Station 1 Station 2
IP address: 10.17.2.12 IP address: 192.168.1.100
WAN: IP address: 10.17.2.0 LAN: IP address: 192.168.1.0
Subnet mask: 255.255.255.0 Subnet mask: 255.255.255.0
V02.00 | 2021/11 47
Setting
Configuring device functions with the web server
48 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
Set up second incoming rule that blocks access via HTTP (port 80):
V02.00 | 2021/11 49
Setting
Configuring device functions with the web server
NOTE
IP forwarding (forwarding of data packets between networks with different IP
address ranges) must be activated.
50 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
Add Destination NAT/PAT Rule (Destination NAT)
In the Add Destination NAT/PAT Rule section, rules for the translation of IP addresses are cre-
ated. For PAT rules, port numbers are specified in addition to IP addresses.
Function Value Meaning
Index 1…64 Order number to prioritize the rules, beginning
with 1 and assigned consecutively
Incoming Zone LAN Network zone from which incoming telegrams are
WAN to be forwarded
Original IP 12.222.2.95 IP address assigned to the device in the external
network
Destination IP 192.168.1.15 IP address in the internal network via which an ex-
ternal device device is to be accessed
Protocol TCP Defines for which telegrams the rule applies
(TCP, UDP, all = OFF).
Incoming Dest. Port 80 Port number of the service
Outgoing Dest. Port 80 (e.g. web server = port 80)
V02.00 | 2021/11 51
Setting
Configuring device functions with the web server
n PAT rule 2:
52 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
8.1.13 IGMP – configuring Multicast
The device supports the functions IGMP Snooper and IGMP Querier.
The IGMP configuration is only effective if Flood unknown Multicasts/Unicasts under Inter-
faces Ò Switching is set to off or IGMP only.
NOTE
In PROFINET networks, the IGMP Snooper function must be deactivated.
IGMP Settings
In the IGMP Settings section, the IGMP settings are made separately for the two networks LAN
and WAN.
Under LAN or WAN, activate the IGMP Snooper and/or or Querier function.
Select the IGMP version.
Define the polling or transmission interval.
Send settings to the device via SET IGMP.
Active IGMP
The Active IGMP table shows all active IGMP requests and responses from connected devices.
V02.00 | 2021/11 53
Setting
Configuring device functions with the web server
54 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
8.1.15 Configuration – accept, reset, load or download the configuration
NOTE
If changes have been made to the configuration compared to the configuration
stored in the device, this is indicated by the entry Nonpersistent Configuration at
the bottom of the web server screen. Configuration changes are only stored in the
device until a device failure or power reset.
If the configuration is to be accepted as a permanent configuration: Activate the
configuration via Make current configuration persistent Ò SAVE as perman-
ent configuration.
V02.00 | 2021/11 55
Setting
Configuring device functions with the web server
56 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
8.2 Downloading the configuration to the device via USB stick
The configuration is transferred via a USB stick using a command file (cmd.json). The file is avail-
able on the product page of the switch at ww.turck.com or can be created in a text editor as
shown below.
ü The configuration of the device was downloaded from the web server via Configuration Ò
Download current configuration.
Download the file cmd.json from the folder ...\usb_commands\apply_and_save_config
and the configuration file *.cfg to the USB stick.
Program code:
{"command":"apply and save config",
"user":"admin",
"password":"password"}
Insert the USB stick with the file cmd.json into the device.
a The RUN LED flashes 3 × green at 1 Hz.
a The RUN LED flashes green at 0.5 Hz.
Within 30 seconds, hold down the Set button for at least 3 seconds to start the update.
a The RUN LED turns off.
a When the RUN LED flashes green (1 Hz), the transfer of the configuration to the device is
complete.
Remove the USB stick.
V02.00 | 2021/11 57
Operating
LED displays
9 Operating
9.1 LED displays
The device has the following LED indicators:
n Power supply
n Status
NOTE
Each of the Ethernet ports XF1…XF10 has an LED L/A.
LED BUS
No function
LED ERR
No function
NOTE
The flashing pattern of the RUN LED indicates the configuration process when using
the USB host function [} 57].
58 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
9.2 Monitoring function
9.2.1 Monitoring – Overview (device overview)
The Overview page shows an overview of all Ethernet interfaces of the device, the device data
(name, firmware version, etc.) and the current device settings (VLAN, DHCP, routing, etc.).
A click on the respective entries opens the corresponding configuration page.
V02.00 | 2021/11 59
Operating
Monitoring function
60 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
a The values are displayed graphically.
V02.00 | 2021/11 61
Operating
Cable diagnostics
62 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
10 Troubleshooting
If the device does not function as expected, first check whether ambient interference is present.
If there is no ambient interference present, check the connections of the device for faults.
If there are no faults, there is a device malfunction. In this case, decommission the device and
replace it with a new device of the same type.
V02.00 | 2021/11 63
Maintenance
Returning devices
11 Maintenance
Ensure that the plug connections and cables are always in good condition.
The devices are maintenance-free, clean dry if required.
12 Repair
The device must not be repaired by the user. The device must be decommissioned if it is faulty.
Observe our return acceptance conditions when returning the device to Turck.
13 Disposal
The devices must be disposed of correctly and must not be included in general
household garbage.
64 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
14 Technical Data
Technical data
Power supply
Supply voltage 24 VDC
Permissible range 8…30 VDC with load dump protection
Current feedthrough
n TBEN-L4/TBEN-L5 (X1 to X2) Max. 9 A per voltage group
n TBEN-LL (XD1 to XD2) Max. 16 A per voltage group
Current consumption at 24 VDC Max. 200 mA
Power loss ≤ 4,8 W
Connectors
Power supply
n TBEN-L4 n X1: 7/8“ male connector, 4-pin
n X2: 7/8'’ female connector, 4-pin
n TBEN-L5 n X1: 7/8“ male connector, 5-pin
n X2: 7/8'’ female connector, 5-pin
n TBEN-LL n XD1: M12 male connector, 5-pin, L-coded
n XD2: M12 female connector, 5-pin, L-coded
Ethernet 2 x M12, 8-pin, X-coded
8 x M12, 4-pin, D-coded
Permissible torques
n Ethernet 0.6 Nm
n Mounting (M6 screws) 1.5 Nm
Isolation voltages
V1 to V2 ≤ 500 V AC
V1/V2 to field bus ≤ 500 V AC
System data
Transmission rate XF1…XF8: 10/100 Mbps
XF9…XF10: 10/100/1000 Mbps
Web server Integrated
Default IP address: 192.168.1.254
Mounting
Type of mounting Via 2 mounting holes, Ø 6.3 mm
Mounting distance (device to device) ≥ 50 mm
Valid for operation in the ambient temperatures
mentioned below with sufficient ventilation as well as
maximum load (horizontal mounting).
For low simultaneity factors and low ambient temper-
atures, mounting distances of < 50 mm may also be
realizable.
Standard/directive conformity
Vibration test According to EN 60068-2-6
Acceleration Up to 20 g
Shock test According to EN 60068-2-27
Drop and topple According to IEC 60068-2-31/IEC 60068-2-32
V02.00 | 2021/11 65
Technical data
Technical data
Electro magnetic compatibility According to EN 61131-2
Approvals and certificates CE
UL
UV-resistant according to DIN EN ISO 4892-2A (2013)
General Information
Dimensions (B × L × H) 64 × 230.4 × 39 mm
Operating temperature -40…+70 °C
Storage temperature -40…+85 °C
Relative humidity 100 %, indoor use (UL only)
Overvoltage category II
Weight 605 g
Operating height Max. 5000 m
Protection class IP65 IP67/IP69K (not evaluated by UL)
Pollution degree 2
MTTF
n TBEN-L4-SE-M2 and TBEN-L5-SE-M2 82 years acc. to SN 29500 (Ed. 99) 20 °C
n TBEN-LL-SE-M2 81 years acc. to SN 29500 (Ed. 99) 20 °C
Housing material PA6-GF30
Halogen-free Yes
FCC declaration
NOTE
This device complies with the limits for a Class A digital device, according to Part 15
of the FCC Rules. Operation of this equipment in a residential area may cause harm-
ful interference. In this case, the user must correct the interference at his own ex-
pense.
66 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
15 Appendix: Approvals and Markings
Approvals Marking according to EN 60079-0/-7/-31
ATEX directive
ATEX approval no.: ÉII 3 G Ex ec IIC T4 Gc
TÜV 20 ATEX 264795 X ÉII 3 D Ex tc IIIC T115 °C Dc
IECEx approval no.: Ex ec IIC T4 Gc
IECEx TUN 20.0010X Ex tc IIIC T115 °C Dc
V02.00 | 2021/11 67
Turck Subsidiaries - Contact Information
68 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com
Mexico Turck Comercial, S. de RL de CV
Blvd. Campestre No. 100, Parque Industrial SERVER, C.P. 25350 Arteaga,
Coahuila
www.turck.com.mx
Netherlands Turck B. V.
Ruiterlaan 7, NL-8019 BN Zwolle
www.turck.nl
V02.00 | 2021/11 69
Over 30 subsidiaries and over
60 representations worldwide!
100013016 | 2021/11
100013016 www.turck.com