Week006 Lab4
Week006 Lab4
Follow the task and steps given. All questions should be answered. This
Laboratory Exercise is 20pts.
Addressing Table
Device Interface IP Address Subnet Mask Default
Gateway
R1 G0/1.1 192.168.1.1 255.255.255.0 N/A
G0/1.10 192.168.100.1 255.255.255.0 N/A
G0/1.20 192.168.200.1 255.255.255.0 N/A
Lo0 209.165.200.225 255.255.255.224 N/A
S1 VLAN 1 192.168.1.11 255.255.255.0 192.168.1.1
S2 VLAN 1 192.168.1.12 255.255.255.0 192.168.1.1
PC-A NIC 192.168.100.3 255.255.255.0 192.168.100.1
PC-B NIC 192.168.200.3 255.255.255.0 192.168.200.1
Objectives
Part 1: Build the Network and Configure Basic Device Settings
Part 2: Configure Switches with VLANs and Trunking
Part 3: Configure Trunk-Based Inter-VLAN Routing
Background / Scenario
A second method of providing routing and connectivity for multiple VLANs is through the use of an
802.1Q trunk between one or more switches and a single router interface. This method is also known
as router-on-a-stick inter-VLAN routing. In this method, the physical router interface is divided into
multiple subinterfaces that provide logical pathways to all VLANs connected.
In this lab, you will configure trunk-based inter-VLAN routing and verify connectivity to hosts on
different VLANs as well as with a loopback on the router.
Note: This lab provides minimal assistance with the actual commands necessary to configure trunk-
based inter-VLAN routing. However, the required configuration commands are provided in the Answer
Course Code IT212
Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs)
with Cisco IOS, Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s
with Cisco IOS, Release 15.0(2) (lanbasek9 image). Other routers, switches and Cisco IOS versions
can be used. Depending on the model and Cisco IOS version, the commands available and output
produced might vary
from what is shown in the labs. Refer to the Router Interface Summary Table at the end of the lab for
the correct interface identifiers.
Note: Make sure that the routers and switches have been erased and have no startup configurations.
Example:
Switch#configure terminal
Switch(config)#
Switch(config)#service password-encryption
Example:
Switch(config)#hostname S1
S1(config)#
Switch(config)#hostname S2
S2(config)#
Example:
S1(config)#no ip domain-lookup
S1(config)#
Configure the EXEC mode password using the enable secret password command. Use class for
the password.
Example:
S1(config)#
Course Code IT212
Example:
********************************
********************************
&
S1(config)#
Use cisco as the password. When you are finished, exit from line configuration mode.
Example:
S1(config)#line console 0
S1(config-line)#password cisco
S1(config-line)#login
S1(config-line)#exit
S1(config)#
G: Do this in router andswitches. Configure the password for the virtual terminal lines.
Use cisco as the password. Include thelogging synchronous command. When you are finished, exit from
line configuration mode.
Example:
S1(config)#line vty 0 4
S1(config-line)#password cisco
S1(config-line)#logging synchronous
S1(config-line)#login
S1(config-line)#exit
S1(config)#
H. Do this command in router and switches. Encrypt all passwords so that even hackers
cann’tuse copy and paste.
S1(config)#service password-encryption
S1(config)#
Step 5: Configure basic settings for the router, same done for the switches. Don’t forget to
enable the ports that needs to be configured using “no shutdown” and save your
configurations.
b. On S1, configure the interface connected to R1 as a trunk. Also configure the interface connected
to S2 as a trunk. Write the commands you used in the space provided.
c. On S1, assign the access port for PC-A to VLAN 10. Write the commands you used in the space
provided.
Part 2: Configure Router and Switches with encapsulation, VLANs and Trunking
Switch S1
S1(config)# vlan 10
S1(config-vlan)# name Students
S1(config-vlan)# vlan 20
S1(config-vlan)# name Faculty
S1(config-vlan)# exit
S1(config)#
S1(config-if)#exit
S1(config)# vlan 1
S1(config-vlan)#ip address 192.168.1.11 255.255.255.0
S1(config-vlan)#no shutdown
S1(config-vlan)#exit
S1(config)#
S1#write mem
Switch S2
S2(config)# vlan 10
S2(config-vlan)# name Students
S2(config-vlan)# vlan 20
S2(config-vlan)# name Faculty
S2(config)# interface f0/1
S2(config-if)# switchport mode trunk
S2(config-if)#no shutdown
S2(config-if)#exit
S2(config)#
S2(config-if)# interface f0/18
S2(config-if)# switchport mode access
S2(config-if)# switchport access vlan 20
S2(config-if)#no shutdown
S2(config-if)#exit
S2(config)#
S2(config)# vlan 1
S2(config-vlan)#ip address 192.168.1.12 255.255.255.0
S2(config-vlan)#no shutdown
S2(config-vlan)#exit
S2(config)#
S1#write mem
Router R1 – Don’t forget to enable all configured interfaces using “no shutdown”.
R1(config)# interface g0/1.1
R1(config-subif)# encapsulation dot1Q 1
R1(config-subif)# ip address 192.168.1.1 255.255.255.0
R1(config-subif)# interface g0/1.10
R1(config-subif)# encapsulation dot1Q 10
R1(config-subif)# ip address 192.168.100.1 255.255.255.0
R1(config-subif)# interface g0/1.20
R1(config-subif)# encapsulation dot1Q 20
R1(config-subif)# ip address 192.168.200.1 255.255.255.0
R1(config-subif)# exit
R1(config)# interface g0/1
R1(config-if)# no shutdown
b. Configure the subinterface to operate on VLAN 1. Write the command you used in the space
provided.
c. Configure the subinterface with the IP address from the Address Table. Write the command you
used in the space provided.
Enter the command to view the routing table on R1. What networks are listed?
From PC-A, is it possible to ping the default gateway for VLAN 10?
From PC-A, is it possible to ping PC-B?
From PC-A, is it possible to ping Lo0
From PC-A, is it possible to ping S2?
If the answer is no to any of these questions, troubleshoot the configurations and correct any errors.