Professional Documents
Culture Documents
Product Manual: Robotics
Product Manual: Robotics
Product manual
IRB 1200
Trace back information:
Workspace 21D version a15
Checked in 2021-12-16
Skribenta version 5.4.005
Product manual
IRB 1200-5/0.9
IRB 1200-5/0.9 type A
IRB 1200-5/0.9 type B
IRB 1200-7/0.7
IRB 1200-7/0.7 type A
IRB 1200-7/0.7 type B
IRC5, OmniCore
Table of contents
Overview of this manual ................................................................................................................... 9
Product documentation .................................................................................................................... 16
How to read the product manual ...................................................................................................... 18
1 Safety 19
1.1 Safety information ............................................................................................. 19
1.1.1 Limitation of liability ................................................................................. 19
1.1.2 Requirements on personnel ...................................................................... 20
1.2 Safety signals and symbols ................................................................................. 21
1.2.1 Safety signals in the manual ...................................................................... 21
1.2.2 Safety symbols on manipulator labels ......................................................... 23
1.3 Robot stopping functions .................................................................................... 29
1.4 Installation and commissioning ............................................................................ 30
1.5 Operation ........................................................................................................ 33
1.6 Maintenance and repair ...................................................................................... 34
1.6.1 Maintenance and repair ............................................................................ 34
1.6.2 Emergency release of the robot axes .......................................................... 37
1.6.3 Brake testing .......................................................................................... 38
1.7 Troubleshooting ................................................................................................ 39
1.8 Decommissioning .............................................................................................. 40
3 Maintenance 115
3.1 Introduction ...................................................................................................... 115
3.2 Maintenance schedule ....................................................................................... 116
3.2.1 Specification of maintenance intervals ........................................................ 116
3.2.2 Maintenance schedule ............................................................................. 117
3.3 Inspection activities ........................................................................................... 119
3.3.1 Inspecting the robot paint ......................................................................... 119
3.3.2 Inspecting the robot cabling ..................................................................... 120
3.3.3 Inspecting the information labels ................................................................ 121
3.3.4 Inspecting mechanical stops .................................................................... 126
3.3.5 Inspecting timing belts ............................................................................ 129
3.3.6 Inspecting the signal lamp (option) ............................................................. 132
3.4 Replacement/changing activities .......................................................................... 134
3.4.1 Replacing the battery pack ....................................................................... 134
3.4.2 Replacing the sealing set on tool flange of Hygienic robots ............................. 144
3.5 Cleaning activities ............................................................................................. 149
3.5.1 Cleaning the IRB 1200 .............................................................................. 149
3.5.2 Cleaning the IRB 1200 with protection type Hygienic ...................................... 152
4 Repair 157
4.1 Introduction ...................................................................................................... 157
4.2 General procedures ........................................................................................... 158
4.2.1 Cut the paint or surface on the robot before replacing parts ............................ 158
4.2.2 Mounting instructions for sealings .............................................................. 161
4.2.3 Sealing differences depending on protection class ........................................ 164
4.2.4 Swing sealing plug for Clean Room, food grade lubrication and Hygienic robots .. 165
4.3 Cable harness .................................................................................................. 169
4.3.1 Replacing the main cable package ............................................................. 169
4.3.2 Replacing the axis-4 FPC unit, housing extender unit and housing extender sealings
............................................................................................................. 245
4.3.3 Replacing the axis-5 FPC unit ................................................................... 277
4.3.4 Replacing the EIB/SMB unit ...................................................................... 291
4.4 Upper and lower arms ........................................................................................ 308
4.4.1 Replacing the lower arm .......................................................................... 308
4.4.2 Replacing the signal lamp ........................................................................ 377
4.4.3 Replacing the tubular spare parts .............................................................. 380
4.4.4 Replacing the axis-3 radial sealing and sealing ring ...................................... 418
4.4.5 Replacing the axis-2 mechanical stop ......................................................... 454
4.4.6 Replacing the axis-3 mechanical stop ......................................................... 457
4.4.7 Replacing the axis-4 mechanical stop ......................................................... 460
4.5 Swing and base ................................................................................................ 492
4.5.1 Replacing the base spare parts (base, axis-1 radial sealing, protection sleeve) ... 492
4.5.2 Replacing the swing spare parts (swing, axis-2 radial sealing) ........................ 572
4.5.3 Replacing the axis-1 mechanical stop ......................................................... 638
4.6 Motors and gearboxes ....................................................................................... 641
4.6.1 Replacing the axis-1 gear unit .................................................................... 641
4.6.2 Replacing the axis-2 drive unit .................................................................. 642
4.6.3 Replacing the axis-3 drive unit .................................................................. 664
4.6.4 Replacing the axis-4 gearbox, drive shaft and pulley ..................................... 686
4.6.5 Replacing the axis-4 motor with pulley ....................................................... 728
4.6.6 Replacing the axis-4 timing belt ................................................................. 740
4.6.7 Replacing the axis-5 motor with pulley ....................................................... 758
4.6.8 Replacing the axis-5 timing belt ................................................................. 771
4.6.9 Replacing the axis-5 and axis-6 drive unit ................................................... 778
5 Calibration 805
5.1 Introduction to calibration ................................................................................... 805
5.1.1 Introduction and calibration terminology ...................................................... 805
6 Decommissioning 867
6.1 Introduction ...................................................................................................... 867
6.2 Environmental information .................................................................................. 868
6.3 Scrapping of robot ............................................................................................. 870
Index 901
Usage
This manual should be used during:
• installation, from lifting the robot to its work site and securing it to the
foundation, to making it ready for operation
• maintenance work
• repair work and calibration.
Prerequisites
Maintenance/repair/installation personnel working with an ABB Robot must:
• be trained by ABB and have the required knowledge of mechanical and
electrical installation/repair/maintenance work.
Organization of chapters
The manual is organized in the following chapters:
Chapter Contents
Safety, service Safety information that must be read through before performing
any installation or service work on robot. Contains general safety
aspects as well as more specific information on how to avoid
personal injuries and damage to the product.
Installation and commis- Required information about lifting and installation of the robot.
sioning
Maintenance Step-by-step procedures that describe how to perform mainten-
ance of the robot. Based on a maintenance schedule that may
be used to plan periodical maintenance.
Repair Step-by-step procedures that describe how to perform repair
activities of the robot. Based on available spare parts.
Chapter Contents
Calibration Calibration procedures and general information about calibration.
Decommissioning Environmental information about the robot and its components.
Reference information Useful information when performing installation, maintenance
or repair work. Includes lists of necessary tools, additional doc-
uments, safety standards, etc.
Spare parts and exploded Reference to the spare part list for the robot.
views
Circuit diagram Reference to the circuit diagram for the robot.
References
Documentation referred to in the manual, is listed in the table below.
General
IRC5
OmniCore
Revisions
Revision Description
- First edition.
Revision Description
A Changes made in this revision:
• Information added about removal of axis-4 mechanical stop and
axis-4 FPC unit from housing extender unit, prior to replacing the
radial sealing at the housing extender unit. See Replacing the
axis-4 FPC unit, housing extender unit and housing extender
sealings on page 245.
• Information added about disconnecting and reconnecting the air
hoses at the tubular, when replacing the axis-4 timing belt. See
Replacing the axis-4 timing belt on page 740.
• Information added about removing screws that fasten the fix sheet
to the inner plastic guide inside housing, when removing axis-3
drive unit, see Creating space for separation of upper and lower
arm on page 669. Information also added about refitting the same
screws, throughout complete manual.
• Information added about releasing the holding brakes prior to ro-
tating axes manually, in calibration procedures, chapter Calibration
on page 805.
• Working range of axis 6 corrected from ±360° to ±400°, see
Working range on page 59.
• Information added about extra o-rings that are enclosed with the
robot at delivery, see Installation of extra O-ring on page 75 and
Installation of extra O-ring on page 108. Also added to repair pro-
cedures, where needed.
• Changed pin number for 24V connection, see Manually releasing
the brakes on page 71.
Revision Description
B Changes made in this revision:
• Information regarding how to read the procedures in this product
manual are updated, see How to read the product manual on
page 18.
• Information added about protection covers for water and dust
proofing, see Protection covers on page 44.
• Information added about transportation bracket that is used during
shipping and transport and must be removed before lifting the
robot, see Transportation bracket on page 45 and Attaching the
roundslings on page 65.
• Timing belt tension of axis-4 and axis-5 motors changed from 13
N and 15 N to 26 N and 30 N, respectively, in repair procedures,
chapter Repair on page 157.
• Tightening torque of M3 screws used on plastic materials changed
from 1.5 Nm to 0.3 Nm, in repair procedures, chapter Repair on
page 157.
• Total amount of harmonic grease 4B No.2 changed from 42 g to
32 g, see Replacing the axis-3 drive unit on page 664.
• Information added about checking PTFE film before refitting the
cable housing cover, see Replacing the EIB/SMB unit on page 291,
Replacing the axis-2 drive unit on page 642, Replacing the axis-3
drive unit on page 664, and Replacing the axis-4 timing belt on
page 740.
• No need to remove and refit cable bracket when removing and
refitting the cable package to the axis-1 sealing ring, see Replacing
the main cable package on page 169.
• No need to remove and refit connector plate when removing and
refitting the axis-5 motor with pulley, see Replacing the axis-4
FPC unit, housing extender unit and housing extender sealings
on page 245, Replacing the axis-4 gearbox, drive shaft and pulley
on page 686, Replacing the axis-5 motor with pulley on page 758.
• No need to remove and refit mechanical stop screw when remov-
ing the axis-4 mechanical stop, see Replacing the axis-4 mechan-
ical stop on page 460.
• Information modified about replacing motor bracket together with
motor flange when removing and refitting the axis-4 motor, see
Replacing the axis-4 gearbox, drive shaft and pulley on page 686
and Replacing the axis-4 motor with pulley on page 728.
• No need to remove tilt covers when replacing axis-5 drive unit,
see Replacing the axis-5 and axis-6 drive unit on page 778.
Revision Description
C Changes made in this revision
• Flange sealing changed from 12340011-116 Loctite 574 to
3HAC026759-002 Sikaflex-521FC for small cover on the housing,
see Replacing the axis-4 FPC unit, housing extender unit and
housing extender sealings on page 245.
• Tightening torque for attachment screws on lifting accessories is
changed from 40 Nm to 15 Nm.
• Tightening torque for lower arm cable
• Tightening torque for the axis-4 FPC unit attachment screws is
changed from 1.5 Nm to 0.3 Nm.
• Added a tightening torque for the attachment screws of the axis-
1 calibration stop pin and the axis-1 calibration pin.
• Added a caution note to keep a straight line when fitting the axis-
1 calibration pin.
• Article number of grease harmonic grease 4B No. 2 changed from
3HAC031695-001 to 3HAC037302-001.
• Total amount of harmonic grease 4B No.2 for axis 2 and axis 5
changed from 80 g and 12 g to 60 g and 9 g, respectively,
• Maximum revolution of axis 6 corrected to ±242°, see Working
range on page 61.
• Clean Room option added.
• Food grade lubrication option added.
• Spare part numbers for several gaskets (IP67) updated.
• The base, the swing and the axis-1 sealing ring are updated due
to IP67 improvements
D Published in release R16.2. The following updates are done in this revi-
sion:
• New standard calibration method introduced (Axis Calibration).
See Calibration on page 805.
• Information about grounding point is added, see Grounding and
bonding point on manipulator on page 108.
• Foundry Plus option added.
E Published in release R17.1. The following updates are done in this revi-
sion:
• A new standard IEC 61340-5-1:2010 added. See Applicable
standards on page 884.
• V-ring on axis-1 sealing ring version 3HAC058568-001 added as
a spare part.
• Notes added for spare part versions. See Description of spare
part versions on page 874.
• Information about Type B robots supporting SafeMove 2 added.
• Plug on base added to options IP67 and Foundry Plus.
Revision Description
F Published in release R17.2. The following updates are made in this revi-
sion:
• Caution about removing metal residues added in sections about
EIB/SMB boards.
• Information about minimum resonance frequency added.
• Bending radius for static floor cables added.
• Updated list of applicable standards.
• Article number for the Calibration tool box, Axis Calibration is
changed.
• Section Start of robot in cold environments on page 114 added.
• Tightening torque of screws securing the axis-5 and axis-6 drive
unit updated.
• Information about mechanically restricting the working range ad-
ded.
• Updated description about Clean Room class.
• Label added to remind the fitting of extra o-ring for robots with
protection class IP67 and with protection type Foundry Plus.
G Published in release R18.1. The following updates are made in this revi-
sion:
• Added sections in General procedures on page 158
• Safety section restructured.
• Note added to clarify the usage of the two M4 thread holes on the
upper arm.
• Added transportation bracket information for robots delivered with
a force control package.
• Updated extra o-ring fitting information for robots with protection
type Clean Room and robots with food grade lubrication.
• Note added to calibration chapter to emphasize the requirement
of equally dressed robot when using previously created reference
calibration values.
• Information about myABB Business Portal added.
• Spare part number of axis-4 gearbox shaft changed from
3HAC049631-001 to 3HAC044692-001.
H Published in release R18.2. The following updates are made in this revi-
sion:
• Added customer connection information.
• Spare part information about axis-2 drive unit and axis-3 drive
unit updated.
• Updated axis-4 and -5 timing belt inspection procedure.
• Added note for transportation bracket removal procedure.
J Published in release R18.2. The following updates are made in this revi-
sion:
• Updated references.
K Published in release 19B. The following updates are made in this revision:
• New touch up color Graphite White available. See Cut the paint
or surface on the robot before replacing parts on page 158.
• New article numbers for manipulator cables in section Robot
cables on page 106.
Revision Description
L Published in release 19D. The following updates are made in this revision:
• Spare part version of axis-1 sealing ring updated. See Spare part
versions for the axis-1 sealing ring on IP40/IP67 robots on page 878.
• Compatibility between cable harness and axis-1 sealing ring ad-
ded. See Spare part versions for the axis-1 sealing ring on
IP40/IP67 robots on page 878.
• Note added about the need to calibrate if the robot is other than
floor mounted. See When to calibrate on page 809.
M Published in release 20B. The following updates are made in this revision:
• Clarified and added information in mounting instructions for rotat-
ing sealings, see Mounting instructions for sealings on page 161.
• Clarified text about position of robot and added table with depend-
encies between axes during Axis Calibration.
• Article number of Calibration tool box, Axis Calibration is changed
from 3HAC062326-001 to 3HAC074119-001.
• Replaced article number and name of grease, previously
3HAB3537-1.
• Added information about Wrist Optimization in calibration chapter.
N Published in release 20C. The following updates are made in this revision:
• Flange sealing changed from 12340011-116 Loctite 574 to
3HAC026759-003 Sikaflex 521FC for tubular covers for robots
with protection class IP67 and protection type Clean Room.
• Updated the figure of customer connection information.
P Published in release 20D. The following updates are made in this revision:
• Added information about maintenance activity of robot overhaul.
Q Published in release 21A. The following updates are made in this revision:
• Added step about applying Loctite 243 to screws securing the
cable housing cover on lower arm for robots with protection class
IP67, protection types Clean Room and Foundry Plus and food
grade lubrication.
R Published in release 21B. The following updates are done in this revision:
• Text regarding fastener quality is updated, see Fastener quality
on page 91.
• Text regarding diameter of air hoses is updated, see Customer
connections on page 111.
S Published in release 21D. The following updates are done in this revision:
• Hygienic option added.
• Controllers OmniCore C30, OmniCore C90XT and OmniCore E10
supported.
Product documentation
Categories for user documentation from ABB Robotics
The user documentation from ABB Robotics is divided into a number of categories.
This listing is based on the type of information in the documents, regardless of
whether the products are standard or optional.
Tip
Product manuals
Manipulators, controllers, DressPack/SpotPack, and most other hardware is
delivered with a Product manual that generally contains:
• Safety information.
• Installation and commissioning (descriptions of mechanical installation or
electrical connections).
• Maintenance (descriptions of all required preventive maintenance procedures
including intervals and expected life time of parts).
• Repair (descriptions of all recommended repair procedures including spare
parts).
• Calibration.
• Decommissioning.
• Reference information (safety standards, unit conversions, screw joints, lists
of tools).
• Spare parts list with corresponding figures (or references to separate spare
parts lists).
• References to circuit diagrams.
Application manuals
Specific applications (for example software or hardware options) are described in
Application manuals. An application manual can describe one or several
applications.
An application manual generally contains information about:
• The purpose of the application (what it does and when it is useful).
• What is included (for example cables, I/O boards, RAPID instructions, system
parameters, software).
• How to install included or required hardware.
• How to use the application.
• Examples of how to use the application.
Operating manuals
The operating manuals describe hands-on handling of the products. The manuals
are aimed at those having first-hand operational contact with the product, that is
production cell operators, programmers, and troubleshooters.
Safety information
The manual includes a separate safety chapter that must be read through before
proceeding with any service or installation procedures. All procedures also include
specific safety information when dangerous steps are to be performed.
Read more in the chapter Safety on page 19.
Illustrations
The product is illustrated with general figures that does not take painting or
protection type in consideration.
Likewise, certain work methods or general information that is valid for several
product models, can be illustrated with illustrations that show a different product
model than the one that is described in the current manual.
1 Safety
1.1 Safety information
Limitation of liability
Any information given in this manual regarding safety must not be construed as a
warranty by ABB that the industrial robot will not cause injury or damage even if
all safety instructions are complied with.
The information does not cover how to design, install and operate a robot system,
nor does it cover all peripheral equipment that can influence the safety of the robot
system.
In particular, liability cannot be accepted if injury or damage has been caused for
any of the following reasons:
• Use of the robot in other ways than intended.
• Incorrect operation or maintenance.
• Operation of the robot when the safety devices are defective, not in their
intended location or in any other way not working.
• When instructions for operation and maintenance are not followed.
• Non-authorized design modifications of the robot.
• Repairs on the robot and its spare parts carried out by in-experienced or
non-qualified personnel.
• Foreign objects.
• Force majeure.
General
Only personnel with appropriate training are allowed to install, maintain, service,
repair, and use the robot. This includes electrical, mechanical, hydraulics,
pneumatics, and other hazards identified in the risk assessment.
Persons who are under the influence of alcohol, drugs or any other intoxicating
substances are not allowed to install, maintain, service, repair, or use the robot.
The plant liable must make sure that the personnel is trained on the robot, and on
responding to emergency or abnormal situations.
Hazard levels
The table below defines the captions specifying the hazard levels used throughout
this manual.
Symbol Designation Significance
DANGER Signal word used to indicate an imminently hazard-
ous situation which, if not avoided, will result in ser-
ious injury.
Introduction to symbols
This section describes safety symbols used on labels (stickers) on the manipulator.
Symbols are used in combinations on the labels, describing each specific warning.
The descriptions in this section are generic, the labels can contain additional
information such as values.
Note
The symbols on the labels on the product must be observed. Additional symbols
added by the integrator must also be observed.
Types of symbols
Both the manipulator and the controller are marked with symbols, containing
important information about the product. This is important for all personnel handling
the robot, for example during installation, service, or operation.
The safety labels are language independent, they only use graphics. See Symbols
on safety labels on page 23.
The information labels can contain information in text.
Symbol Description
Warning!
Warns that an accident may occur if the instructions are not
followed that can lead to serious injury, possibly fatal, and/or
great damage to the product. It applies to warnings that apply
xx0900000812
to danger with, for example, contact with high voltage electrical
units, explosion or fire risk, risk of poisonous gases, risk of
crushing, impact, fall from height, etc.
Caution!
Warns that an accident may occur if the instructions are not
followed that can result in injury and/or damage to the product.
It also applies to warnings of risks that include burns, eye injury,
skin injury, hearing damage, crushing or slipping, tripping, im-
xx0900000811 pact, fall from height, etc. Furthermore, it applies to warnings
that include function requirements when fitting and removing
equipment where there is a risk of damaging the product or
causing a breakdown.
Prohibition
Used in combinations with other symbols.
xx0900000839
Symbol Description
See user documentation
Read user documentation for details.
Which manual to read is defined by the symbol:
• No text: Product manual.
• EPS: Application manual - Electronic Position Switches.
xx0900000813
xx0900000816
Do not disassemble
Disassembling this part can cause injury.
xx0900000815
Extended rotation
This axis has extended rotation (working area) compared to
standard.
xx0900000814
Brake release
Pressing this button will release the brakes. This means that
the robot arm can fall down.
xx0900000808
Symbol Description
Tip risk when loosening bolts
The robot can tip over if the bolts are not securely fastened.
xx0900000810
xx1500002402
Crush
Risk of crush injuries.
xx0900000817
Symbol Description
Heat
Risk of heat that can cause burns. (Both signs are used)
xx0900000818
!
3HAC 4431-1/06
xx1300001087
Moving robot
4 6 The robot can move unexpectedly.
3 5
1
xx0900000819
xx1000001141
2 3
xx1500002616
Symbol Description
Brake release buttons
xx0900000820
xx1000001140
Lifting bolt
xx0900000821
xx1000001242
Lifting of robot
xx0900000822
Oil
Can be used in combination with prohibition if oil is not allowed.
xx0900000823
Mechanical stop
xx0900000824
Symbol Description
No mechanical stop
xx1000001144
Stored energy
Warns that this part contains stored energy.
Used in combination with Do not disassemble symbol.
xx0900000825
Pressure
Warns that this part is pressurized. Usually contains additional
text with the pressure level.
xx0900000826
xx0900000827
Do not step
Warns that stepping on these parts can cause damage to the
parts.
xx1400002648
Layout
The robot integrated to a robot system shall be designed to allow safe access to
all spaces during installation, operation, maintenance, and repair.
If robot movement can be initiated from an external control panel then an emergency
stop must also be available.
If the manipulator is delivered with mechanical stops, these can be used for reducing
the working space.
A perimeter safeguarding, for example a fence, shall be dimensioned to withstand
the following:
• The force of the manipulator.
• The force of the load handled by the robot if dropped or released at maximum
speed.
• The maximum possible impact caused by a breaking or malfunctioning
rotating tool or other device fitted to the robot.
The maximum TCP speed and the maximum velocity of the robot axes are detailed
in the section Robot motion in the product specification for the respective
manipulator.
Consider exposure to hazards, such as slipping, tripping, and falling.
Hazards due to the working position and posture for a person working with or near
the robot shall be considered.
Hazards due to noise emission from the robot needs to be considered.
Consider hazards from other equipment in the robot system, for example, that
guards remain active until identified hazards are reduced to an acceptable level.
Allergenic material
See Environmental information on page 868 for specification of allergenic materials
in the product, if any.
Electrical safety
Incoming mains must be installed to fulfill national regulations.
The power supply wiring to the robot must be sufficiently fused and if necessary,
it must be possible to disconnect it manually from the mains power.
The power to the robot must be turned off with the main switch and the mains
power disconnected when performing work inside the controller cabinet. Lock and
tag shall be considered.
Harnesses between controller and manipulator shall be fixed and protected to
avoid tripping and wear.
Wherever possible, power on/off or rebooting the robot controller shall be performed
with all persons outside the safeguarded space.
Note
Use a CARBON DIOXIDE (CO2) extinguisher in the event of a fire in the robot.
Safety devices
The integrator is responsible for that the safety devices necessary to protect people
working with the robot system are designed and installed correctly.
When integrating the robot with external devices to a robot system:
• The integrator of the robot system must ensure that emergency stop functions
are interlocked in accordance with applicable standards.
• The integrator of the robot system must ensure that safety functions are
interlocked in accordance with applicable standards.
Other hazards
A robot may perform unexpected limited movement.
WARNING
Manipulator movements can cause serious injuries on users and may damage
equipment.
The risk assessment should also consider other hazards arising from the
application, such as, but not limited to:
• Water
• Compressed air
• Hydraulics
End-effector hazards require particular attention for applications which involve
close human collaboration with the robot.
Note
1.5 Operation
Automatic operation
Verify the application in the operating mode manual reduced speed, before changing
mode to automatic and initiating automatic operation.
WARNING
Hazards due to the use of brake release devices and/or gravity beneath the
manipulator shall be considered.
A robot may perform unexpected limited movement.
WARNING
Manipulator movements can cause serious injuries on users and may damage
equipment.
General
Corrective maintenance must only be carried out by personnel trained on the robot.
Maintenance or repair must be done with all electrical, pneumatic, and hydraulic
power switched off, that is, no remaining hazards.
Hazards due to stored mechanical energy in the manipulator for the purpose of
counterbalancing axes must be considered before maintenance or repair.
Never use the robot as a ladder, which means, do not climb on the controller,
manipulator, including motors, or other parts. There are hazards of slipping and
falling. The robot might be damaged.
Make sure that there are no loose screws, turnings, or other unexpected parts
remaining after work on the robot has been performed.
When the work is completed, verify that the safety functions are working as
intended.
Hot surfaces
Surfaces can be hot after running the robot, and touching these may result in burns.
Allow the surfaces to cool down before maintenance or repair.
Allergic reaction
Allergic reaction
Note
Allergic reaction
When opening the oil or grease Open the plug carefully and keep
plug, there may be pressure away from the opening. Do not
present in the gearbox, causing overfill the gearbox when filling.
lubricant to spray from the
opening.
Possible pressure
build-up in gearbox
Overfilling of gearbox lubricant Make sure not to overfill the
can lead to internal over-pres- gearbox when filling it with oil or
sure inside the gearbox which in grease.
turn may: After filling, verify that the level
• damage seals and gas- is correct.
Do not overfill kets
• completely press out
seals and gaskets
• prevent the robot from
moving freely.
The specified amount of oil or After filling, verify that the level
grease is based on the total is correct.
volume of the gearbox. When
changing the lubricant, the
amount refilled may differ from
the specified amount, depending
Specified amount de- on how much has previously
pends on drained been drained from the gearbox.
volume
For lifetime reasons always drain
as much oil as possible from the
gearbox. The magnetic oil plugs
will gather residual metal chips.
Contaminated oil in
gearboxes
WARNING
Hazards due to the use of brake release devices and/or gravity beneath the
manipulator shall be considered.
A robot may perform unexpected limited movement.
WARNING
Manipulator movements can cause serious injuries on users and may damage
equipment.
Related information
See also the safety information related to installation and operation.
Description
In an emergency situation, the brakes on a robot axis can be released manually
by pushing a brake release button.
How to release the brakes is described in the section:
• Manually releasing the brakes on page 71.
The robot may be moved manually on smaller robot models, but larger models
may require using an overhead crane or similar equipment.
Increased injury
Before releasing the brakes, make sure that the weight of the manipulator does
not result in additional hazards, for example, even more severe injuries on a trapped
person.
DANGER
When releasing the holding brakes, the robot axes may move very quickly and
sometimes in unexpected ways.
Make sure no personnel is near or beneath the robot.
When to test
During operation, the holding brake of each axis normally wears down. A test can
be performed to determine whether the brake can still perform its function.
How to test
The function of the holding brake of each axis motor may be verified as described
below:
1 Run each axis to a position where the combined weight of the manipulator
and any load is maximized (maximum static load).
2 Switch the motor to the MOTORS OFF.
3 Inspect and verify that the axis maintains its position.
If the manipulator does not change position as the motors are switched off,
then the brake function is adequate.
Note
1.7 Troubleshooting
General
When troubleshooting requires work with power switched on, special considerations
must be taken:
• Safety circuits might be muted or disconnected.
• Electrical parts must be considered as live.
• The manipulator can move unexpectedly at any time.
DANGER
WARNING
Hazards due to the use of brake release devices and/or gravity beneath the
manipulator shall be considered.
A robot may perform unexpected limited movement.
WARNING
Manipulator movements can cause serious injuries on users and may damage
equipment.
Related information
See also the safety information related to installation, operation, maintenance, and
repair.
1.8 Decommissioning
General
See section Decommissioning on page 867.
WARNING
Hazards due to the use of brake release devices and/or gravity beneath the
manipulator shall be considered.
A robot may perform unexpected limited movement.
WARNING
Manipulator movements can cause serious injuries on users and may damage
equipment.
General
This chapter contains assembly instructions and information for installing the IRB
1200 at the working site.
See also the product manual for the robot controller.
The installation must be done by qualified installation personnel in accordance
with the safety requirements set forth in the applicable national and regional
standards and regulations.
Safety information
Before any installation work is commenced, all safety information must be observed.
There are general safety aspects that must be read through, as well as more specific
safety information that describes the danger and safety risks when performing the
procedures. Read the chapter Safety on page 19 before performing any installation
work.
Note
Always connect the IRB 1200 and the robot to protective earth and residual
current device (RCD) before connecting to power and starting any installation
work.
For more information see:
• Product manual - OmniCore C30
• Product manual - OmniCore C90XT
• Product manual - OmniCore E10
• Product manual - IRC5
• Product manual - IRC5 Compact
2.2 Unpacking
xx1500000243
xx1500000242
xx1500000241
A label, as shown in the following, is fitted on the connector to remind the fitting
of extra O-ring 3HAB3772-19. The label must be removed before the O-ring and
main cable is fitted.
Label for IP67, Foundry Plus, Clean Room and food grade lubrication robots
xx2100001272
Further information
For installation information, see Orienting and securing the robot on page 74 and
Electrical connections on page 106.
Note
For robots delivered with option 636-1 Force Control Package (IRC5)
For robot delivered with option 3038-1 Force Control Interface (OmniCore)
The transportation bracket is installed on the force sensor.
xx1800000002
xx1500001605 xx1800000003
xx1800000004
Note
The bracket must be kept for reuse after removal. Once robot shipping and
transportation are required, the transportation bracket has to be reinstalled for
securing the robot position.
Action Note
1 Move the robot to an appropriate position. Taking IRB 1200-5/0.9 as an ex-
ample
WARNING
A
xx1500001399
A B
IRB 1200 all vari- 10° 25°
ants (not in protec-
tion type Hygienic)
IRB 1200-7/0.7 (in 11.95° 25.66°
protection type Hy-
gienic)
IRB 1200-5/0.9 (in 11.77° 25.48°
protection type Hy-
gienic)
2
CAUTION
Action Note
3 Remove the screws and washers.
CAUTION
xx1500001604
xx1800000005
xx1600001178
xx1500001400
Action Note
5 For robots with protection type Clean Room Swing sealing plug: 3HAC053687-
For robots with food grade lubrication 001
For robots with protection type Hygienic
Make sure the swing sealing plug is intact and the
sealant around fully covers the joint.
If not, replace the swing sealing plug and seal the
joint. See Swing sealing plug for Clean Room,
food grade lubrication and Hygienic robots on
page 165.
After the replacement, wipe clean.
xx1600000205
6 For robots with protection type Foundry Plus Protection plug for lifting holes:
Fit protection plugs to the lifting holes. 3HAC4836-24
xx1600001147
Introduction
This section is intended for use when unpacking and installing the robot for the
first time. It also contains information useful during later re-installation of the robot.
Action
1 Make a visual inspection of the packaging and make sure that nothing is damaged.
2 Remove the packaging.
3 Check for any visible transport damage.
Note
Action
5 Make sure that the lifting accessory used (if required) is suitable to handle the weight
of the robot as specified in: Weight, robot on page 50
6 If the robot is not installed directly, it must be stored as described in: Storage condi-
tions, robot on page 53
7 Make sure that the expected operating environment of the robot conforms to the
specifications as described in: Operating conditions, robot on page 53
8 Before taking the robot to its installation site, make sure that the site conforms to:
• Loads on foundation, robot on page 51
• Protection classes, robot on page 53
• Requirements, foundation on page 52
9 Before moving the robot, please observe the stability of the robot: Risk of tipping/sta-
bility on page 62
10 When these prerequisites are met, the robot can be taken to its installation site as
described in section: On-site installation on page 65
11 Install required equipment, if any.
• Installing the signal lamp on IRC5 robots on page 94
Weight, robot
The table shows the weight of the robot.
Robot model Weight
IRB 1200 IRB 1200-5/0.9: 54 kg
IRB 1200-7/0.7: 52 kg
Note
The weight does not include tools and other equipment fitted on the robot.
Txy
Fz
Fxy
Tz
xx1100000521
The table shows the various forces and torques working on the robot during different
kinds of operation.
Note
These forces and torques are extreme values that are rarely encountered during
operation. The values also never reach their maximum at the same time!
WARNING
The robot installation is restricted to the mounting options given in following load
table(s).
Floor mounted
Wall mounted
Suspended
Requirements, foundation
The table shows the requirements for the foundation where the weight of the
installed robot is included:
Requirement Value Note
Flatness of foundation 0.1/500 mm Flat foundations give better repeatability of the
surface resolver calibration compared to original settings
on delivery from ABB.
The value for levelness aims at the circumstance
of the anchoring points in the robot base.
In order to compensate for an uneven surface,
the robot can be recalibrated during installation.
If resolver/encoder calibration is changed this
will influence the absolute accuracy.
Maximum tilt 5º The limit for the maximum payload on the robot
is reduced if the robot is tilted from 0°.
Contact ABB for further information about accept-
able loads.
Minimum resonance 22 Hz The value is recommended for optimal perform-
frequency ance.
Note Due to foundation stiffness, consider robot mass
including equipment. i
It may affect the For information about compensating for founda-
manipulator life- tion flexibility, see the application manual of the
time to have a controller software, section Motion Process
lower resonance Mode.
frequency than
recommended.
i The minimum resonance frequency given should be interpreted as the frequency of the robot
mass/inertia, robot assumed stiff, when a foundation translational/torsional elasticity is added, i.e.,
the stiffness of the pedestal where the robot is mounted. The minimum resonance frequency should
not be interpreted as the resonance frequency of the building, floor etc. For example, if the equivalent
mass of the floor is very high, it will not affect robot movement, even if the frequency is well below
the stated frequency. The robot should be mounted as rigid as possibly to the floor.
Disturbances from other machinery will affect the robot and the tool accuracy. The robot has
resonance frequencies in the region 10 – 20 Hz and disturbances in this region will be amplified,
although somewhat damped by the servo control. This might be a problem, depending on the
requirements from the applications. If this is a problem, the robot needs to be isolated from the
environment.
Note
For robots with protection type Hygienic, the foundation where the robot is
installed and the robot base must be far away from the food contact areas.
2.2.5 Dimensions
42
350
869
399,1
105 105
210 210
269
(C)
115
(D)
47
185 105
190 162
210
269,5
xx1300000366
Position Description
A Minimum turning radius axis 4 R=79 mm
B Minimum turning radius axis 3 R=139 mm
C Minimum turning radius axis 1 R=138 mm
D Valid for option Robot cabling routing, 966-1 From below
42
350
869
399.1
105
105 210
210 269
(C)
115
(D) 47
185 105
190 162
210
269,5
xx2100001277
Position Description
A Minimum turning radius axis 4 R=79 mm
B Minimum turning radius axis 3 R=139 mm
C Minimum turning radius axis 1 R=138 mm
D Valid for option Robot cabling routing, 966-1 From below
613
(A)
(B) 451 82
42
448
967
399,1
105 105
210 210
269
(C)
115
(D)
47
185 105
190 162
210
269,5
xx1400000339
Pos Description
A Minimum turning radius axis 4 R=79 mm
B Minimum turning radius axis 3 R=111 mm
C Minimum turning radius axis 1 R=138 mm
D Valid for option Robot cabling routing, 966-1 From below
42
448
967
399.1
105 105
210 210
269
(C)
115
(D) 47
185 105
190 162
210
269,5
xx2100001278
Position Description
A Minimum turning radius axis 4 R=79 mm
B Minimum turning radius axis 3 R=139 mm
C Minimum turning radius axis 1 R=138 mm
D Valid for option Robot cabling routing, 966-1 From below
Pos 1
Z
Pos 0
Pos 6 Pos 9
1304
Pos 7 Pos 2
Pos 3
Pos 8
Pos 5
202
Pos 4
703 703
xx1300000386
Pos 1
Z
Pos 0
1642
Pos 9
Pos 6
Pos 8
342
Pos 5 Pos 4
901 901
xx1300000387
B (7/0.7)
B (5/0.9)
C (7/0.7)
C (5/0.9)
170°
xx1400000681
Working range
Risk of tipping
Do not change the robot position before securing it to the foundation.
The shipping position is the most stable position.
A
xx1500001399
A B
IRB 1200 all variants (not in protection type Hygienic) 10° 25°
A B
IRB 1200-7/0.7 (in protection type Hygienic) 11.95° 25.66°
IRB 1200-5/0.9 (in protection type Hygienic) 11.77° 25.48°
Transportation bracket
A transportation bracket is installed and delivered together with the robot for
securing the robot position during shipping and transportation. The transportation
bracket must be removed before fitting the lifting accessory to the robot during the
lifting of the robot to the installation site.
For details, see Transportation bracket on page 45.
WARNING
The robot will be mechanically unstable if not properly secured to the foundation.
Description
ESD (electrostatic discharge) is the transfer of electrical static charge between two
bodies at different potentials, either through direct contact or through an induced
electrical field. When handling parts or their containers, personnel not grounded
may potentially transfer high static charges. This discharge may destroy sensitive
electronics.
Safe handling
Use one of the following alternatives:
• Use a wrist strap.
Wrist straps must be tested frequently to ensure that they are not damaged
and are operating correctly.
• Use an ESD protective floor mat.
The mat must be grounded through a current-limiting resistor.
• Use a dissipative table mat.
The mat should provide a controlled discharge of static voltages and must
be grounded.
Note
A transportation bracket is installed and delivered together with the robot for
securing the robot position during shipping and transport. The transportation
bracket must be removed before fitting the lifting accessory to the robot during
the lifting of the robot to the installation site.
For details, see Transportation bracket on page 45.
xx1400000501
Required equipment
WARNING
A
xx1500001399
A B
IRB 1200 all variants 10° 25°
(not in protection
type Hygienic)
IRB 1200-7/0.7 (in 11.95° 25.66°
protection type Hy-
gienic)
IRB 1200-5/0.9 (in 11.77° 25.48°
protection type Hy-
gienic)
Action Note
2
CAUTION
xx1600001147
Action Note
4 Fit the lifting tools to the robot. Lifting accessory, robot: 3HAC049711-
Use the enclosed screws. 001
For robots with protection type Foundry Plus
Use two M10 rubber washers, as circled in the
figure, on the lifting holes at each side of the
robot (4 pcs in total) for protection when fitting
the lifting tools.
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Pay attention not to damage the swing sealing
plug and the sealant covering the joint when
fitting the lifting tools.
xx1400000498
Tightening torque: 15 Nm
For robots with protection type
Foundry Plus
xx1600000205
xx1600001177
Replace the swing sealing plug if damaged and
seal the joint. See Swing sealing plug for Clean
Room, food grade lubrication and Hygienic
robots on page 165.
After the replacement, wipe clean.
5 Fit the roundslings to the lifting tools and attach Make sure the roundsling has free
them to the lifting beam. space and does not wear against any
part of the robot.
Roundsling, 1.5 m
xx1400000511
Action Note
6 Fit the roundslings to the lifting beam and to Roundsling, 0.6 m
the overhead crane.
xx1400000501
7
CAUTION
8
WARNING
xx1600000005
Introduction
How to lift and turn the robot to a suspended position using the turning accessory
is described in the lifting instruction delivered with the turning accessory. Article
numbers for the accessory and the instruction is specified in Special tools on
page 891. Any additional equipment required is specified in the instruction for the
lifting accessory. Contact ABB for more information.
How to lift and turn the robot into position for wall position: Contact ABB for more
information.
How to lift and turn the robot into position for tilted position: Contact ABB for more
information.
xx1400000030
xx1400000030
2
DANGER
Action Note
2 Supply +24V on pin 11 and 0V on pin 12.
Note
xx1400000031
Introduction
This section details how to orient and secure the robot to the foundation or base
plate in order to run the robot safely. The requirements made on the foundation
are shown in sections:
• Loads on foundation, robot on page 51
• Requirements, foundation on page 52.
+ 0,018
180
2x 6 H8 0
0.03 70
95
180
95
F
F
13,5
0.3
70
4x
16
F-F
xx1300000368
xx0900000643
xx1500000241
4
CAUTION
5 Lift the robot to its installation site. How to lift the robot is described in
section:
• Lifting robot with roundslings
on page 65
6 For robots with protection class IP67
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Cabling routed from below
Fit the O-ring 3HAB3772-141 to underneath the
robot base. xx1500000241
7 Fit two pins to the holes in the base. 2 pcs, D6x20, ISO 2338 - 6m6x20 -
A1
8 Guide the robot gently, using the attachment Make sure the robot base is cor-
screws while lowering it into its mounting posi- rectly fitted onto the pins.
tion.
9 Fit the securing screws and washers in the attach- Screws: M12x35 (robot installation
ment holes of the base. directly on foundation), quality: 8.8
10 Tighten the bolts in a criss-cross pattern to en- Tightening torque:
sure that the base is not distorted. 55 Nm ± 5 Nm
Action Information
11 For robots with protection class IP67 Robots with manipulator cables
routed from the rear of the base:
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Fit the O-ring 3HAB3772-19 to the main power
connector on the robot base.
xx1500000243
xx1500000242
General
The robot is configured for mounting parallel to the floor, without tilting, on delivery.
The method for mounting the robot in a suspended (upside down) or tilted position
is basically the same as for floor mounting, but the system parameters that describe
the mounting angle (how the robot is oriented relative to the gravity) must be
re-defined.
Note
With suspended installation, make sure that the gantry or corresponding structure
is rigid enough to prevent unacceptable vibrations and deflections, so that
optimum performance can be achieved.
Note
The allowed mounting positions are described in the product specification for
the robot. The requirements on the foundation are described in Requirements,
foundation on page 52.
System parameters
Note
Gravity Beta
If the robot is mounted upside down or on a wall (rotated around the y-axis), then
the robot base frame and the system parameter Gravity Beta must be redefined.
Gravity Beta should then be π (+3.141593) if the robot is mounted upside down
(suspended), or ±π/2 (±1.570796) if mounted on a wall.
The Gravity Beta is a positive rotation direction around the y-axis in the base
coordinate system. The value is set in radians.
Gravity Alpha
If the robot is mounted on a wall (rotated around the x-axis), then the robot base
frame and the system parameter Gravity Alpha must be redefined. The value of
Gravity Alpha should then be ±π/2 (±1.570796).
The Gravity Alpha is a positive rotation direction around the x-axis in the base
coordinate system. The value is set in radians.
Note
The system parameter Gravity Alpha is not supported for all robot types. It is not
supported for IRB 140, IRB 1410, IRB 1600ID, IRB 2400, IRB 4400, IRB 6400R,
IRB 6400 (except for IRB 6400 200/2.5 and IRB 6400 200/2.8), IRB 6600, IRB
6650, IRB 6650S and IRB 7600 (except for IRB 7600 325/3.1).
If the robot does not support Gravity Alpha, then use Gravity Beta along with the
recalibration of axis 1 to define the rotation of the robot around the x-axis.
Note
The parameter is supported for all robots on track when the system parameter
7 axes high performance motion is set, see Technical reference manual - System
parameters.
Gamma Rotation
Gamma Rotation defines the orientation of the robot foot on the travel carriage
(track motion).
xx1400000682
xx1500000532
Note
2.3.6 Loads fitted to the robot, stopping time and braking distances
General
Any loads mounted on the robot must be defined correctly and carefully (with
regard to the position of center of gravity and mass moments of inertia) in order
to avoid jolting movements and overloading motors, gears and structure.
CAUTION
Incorrectly defined loads may result in operational stops or major damage to the
robot.
References
Load diagrams, permitted extra loads (equipment) and their positions are specified
in the product specification. The loads must be defined in the software.
• Operating manual - IRC5 with FlexPendant
• Operating manual - OmniCore
General
Extra loads can be mounted on to the upper arm. Definitions of load area and
permitted load are shown in figure below. The center of gravity of the extra load
shall be within the marked load areas. The robot is supplied with holes for fitting
of extra equipment. (See Holes for fitting extra equipment on page 85).
68
(A) (A)
216
216
150
68
34 (A)
IRB 1200-7/0.7
108
216
250
68
34
(A)
IRB 1200-5/0.9
108
216
xx1300000384
Upper arm
90 ±0,125
2 x M4 8
(A) 82
78
58
42
85
152
(B)
2 x M4 8
2xM5 7.5
20 ±0.125
30 ±0.15
xx1300000381
Pos Description
A IRB 1200-5/0.9 = 451 mm, IRB 1200-7/0.7 = 351 mm
B IRB 1200-5/0.9 = 216 mm, IRB 1200-7/0.7 = 116 mm
Note
The two M4 thread holes shown in the following figure are used for fitting the
cable harness or air hoses of the tools rather than fitting extra equipment.
2 x M4 8
xx1700002331
2xM4 10
(A) 91
58
78
42
85
90 ±0.125
(B)
2xM5 7.5
30 ±0.15
xx2100001279
Pos Description
A IRB 1200-5/0.9 = 451 mm, IRB 1200-7/0.7 = 351 mm
B IRB 1200-5/0.9 = 216 mm, IRB 1200-7/0.7 = 116 mm
Note
The two M4 thread holes shown in the following figure are used for fitting the
cable harness or air hoses of the tools rather than fitting extra equipment.
2xM4 10
xx2100001280
Lower arm
2 x M5 7.5
666,1
568,1
30 ±0,15
Frame
30 ±0.15
2xM10 10
78 B
(A)
243 B
105
xx1400000590
Pos Description
A Holes on both sides
40 h7
J 4
4xM5 6
4x 90°
0.25
31.5 45° 5
J
J-J
xx1300000383
+ 0.021
40 h7 -0.025
0.04
0
E
4xM5 6 6.5
20 H7
0.25 4
4x 90°
31.5 E 45° 5
E-E
xx1600001322
45° 4 5°
+0.012
A 5 H7 0
0.04 B
7
+0.021
6
0
44
20 H7
B
31.5 7
B
B
SECTION A-A
A
7 8
4xM5
0.25 4x 5.5
0.25
SECTION B-B
xx2100001281
Fastener quality
When fitting tools on the tool flange, only use screws with quality 12.9. For other
equipment use suitable screws and tightening torque for your application.
For robots with protection type Hygienic, the gap between the tool flange and tool
must be sealed by fitting a gasket, guide pin, stainless flange bolts and FDA
washers, which are packaged (package number: 3HAC078800-001) with the robot
at delivery.
xx2100002211
When designing the tools to be fit on the tool flange, make sure the tool dimension
meets the following requirements in addition to the dimension of the robot tool
flange specified in Robot tool flange on page 89.
5~6
Greater than 3
+0.1 !"#" $ $
1.1 0 A % &
xx2100002644
General
A signal lamp with an yellow fixed light can be mounted on the robot, as a safety
device. The signal lamp is required on an UL/UR approved robot.
The lamp is active in MOTORS ON mode.
xx1300000455
Required tools
Action Note
1
DANGER
2
CAUTION
xx1300000464
xx1300000465
Action Note
7 Refit the cover on the upper arm housing. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
xx1300000456
Note
Note
Description
A signal lamp with a yellow fixed light can be mounted in the cell or any other
visible location, and driven by I/O signal or MON_LAMP signal from the controller,
to comply with the UL1740 standard.
Function
The lamp is active in MOTORS ON mode.
Action
1
DANGER
Make sure that all supplies for electrical power, hydraulic pressure, and air pressure
are turned off.
Note
The local I/O connectors provides 16 digital output signals for use.
Note
4 Configure the lamp by adding a System Output type signal with status set to Motors
On State.
5 The lamp is now ready for use and is lit in MOTORS ON mode.
Action
1
DANGER
Make sure that all supplies for electrical power, hydraulic pressure, and air pressure
are turned off.
Note
Action
3 For robots with OmniCore E line
Connect the lamp cable connector to the MON connector on the controller.
Note
4 The lamp is now ready for use and is lit in MOTORS ON mode.
Further information
Further information about the MOTORS ON/MOTORS OFF mode may be found in
the product manual for the controller.
Further information about how to set up I/O system may be found in Technical
reference manual - System parameters.
General
When installing the robot, make sure that it can move freely within its entire working
space. If there is a risk that it may collide with other objects, its working space
should be limited.
The working range of the following axes may be restricted:
• Axis 1, hardware (mechanical stop) and software. Note! The axis 1 stop is a
fixed stop that must be installed during operation of robot!
• Axis 2, hardware (mechanical stop) and software. Note! The axis 2 stop is a
fixed stop that must be installed during operation of robot!
• Axis 3, hardware (mechanical stop) and software. Note! The axis 3 stop is a
fixed stop that must be installed during operation of robot!
• Axis 4, hardware (mechanical stop) and software. Note! The axis 4 stop is a
fixed stop that must be installed during operation of robot!
• Axis 5, hardware (mechanical stop) and software
• Axis 6, software
This section describes how to install hardware that restricts the working range.
Note
xx1700001293
xx1700001294
xx1700001295
xx1700001296
xx1700001297
The axis-1, axis-2, axis-3, and axis-4 stops are fixed stops that must be installed
during operation of robot. For details about how to install the stops, see:
• Replacing the axis-1 mechanical stop on page 638
• Replacing the axis-2 mechanical stop on page 454
• Replacing the axis-3 mechanical stop on page 457
• Replacing the axis-4 mechanical stop on page 460
General
Robots with protection type Clean Room are specially designed to work in a clean
room environment.
Clean Room robots are designed to prevent from particle emission from the robot.
For example, the maintenance work possible to perform without cracking the paint.
The robot is painted with four layers of polyurethane paint. The last layer being a
varnish over labels to simplify cleaning. The paint has been tested regarding
outgassing of Volatile Organic Compounds (VOC) and been classified in accordance
with ISO 14644-8.
Any Clean Room parts that are replaced must be replaced with parts designed for
use in Clean Room environments.
Introduction
Connect the robot and controller to each other after securing them to the foundation.
The lists below specify which cables to use for each respective application.
Robot cables
These cables are included in the standard delivery. They are completely
pre-manufactured and ready to plug in.
Cable sub-category Description Connection Connection
point, cabinet point, robot
Robot cable, power Transfers drive power from the XS1 (IRC5 con- R1.MP
drive units in the control cabinet trollers)
to the robot motors. X1 (OmniCore
controllers)
Robot cable, signals Transfers encoder data from XS2 (IRC5 con- R1.EIB
and power supply to the en- trollers)
coder interface board. X2 (OmniCore
Transfers resolver data from controllers)
and power supply to the serial
measurement board.
The following table lists the power cables for connecting OmniCore controller.
The following table lists the signal cables for connecting OmniCore controller.
A
B
xx1600002016
A Diameter
B Diameter x10
xx1600001081
The O-ring specified below is delivered together with the robot and must be installed
to the main power connector during electrical installation.
Equipment Art. no. Note
O-ring 3HAB3772-19 For robots with protection class IP67
For robots with protection type Foundry
Plus
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Used to seal between the main power
cable and the connector.
Robots with manipulator cables routed
from the rear of the base:
xx1500000243
xx1500000242
The following table lists the CP/CS cables for connecting OmniCore controller.
The following table lists the Ethernet cables for connecting OmniCore controller.
xx1600001687
There is also connections for Ethernet, one connector R4.Ethernet at the tubular
housing and the corresponding connector R1.Ethernet located at the base.
Hose for compressed air is also integrated into the manipulator. There are 4 inlets
at the base (R1/8”) and 4 outlets (M5) on the tubular housing.
(C) (B)
(A)
(B)
(C)
(A)
xx1300000385
Connectors
The tables describes the connectors on base and tubular housing (upper arm).
Connectors, base
Air, connector
Introduction
This section describes how to start the robot in a cold environment if it is not starting
the normal way.
If the program consists of large wrist movements, it is possible that the reorientation
velocity, which is always high in predefined velocities, needs to be included in the
ramping up.
3 Maintenance
3.1 Introduction
Safety information
Observe all safety information before conducting any service work.
There are general safety aspects that must be read through, as well as more specific
safety information that describes the danger and safety risks when performing the
procedures. Read the chapter Safety on page 19 before performing any service
work.
The maintenance must be done by qualified personnel in accordance with the
safety requirements set forth in the applicable national and regional standards and
regulations.
Note
If the IRB 1200 is connected to power, always make sure that the IRB 1200 is
connected to protective earth and a residual current device (RCD) before starting
any maintenance work.
For more information see:
• Product manual - OmniCore C30
• Product manual - OmniCore C90XT
• Product manual - OmniCore E10
• Product manual - IRC5
• Product manual - IRC5 Compact
• Robot cabling and connection points on page 106.
Introduction
The intervals are specified in different ways depending on the type of maintenance
activity to be carried out and the working conditions of the IRB 1200:
• Calendar time: specified in months regardless of whether the system is
running or not.
• Operating time: specified in operating hours. More frequent running means
more frequent maintenance activities.
Robots with the functionality Service Information System activated can show active
counters in the device browser in RobotStudio, or on the FlexPendant.
Overhaul
Depending on application and operational environment a complete overhaul may
be necessary in average around 30000 hours.
ABB Connected Services and its Assessment tools can help you to identify the
real stress level of your robot, and define the optimal ABB support to maintain your
robot working.
Contact your local ABB Customer Service to get more information.
Every 36 months
Regularly i
hours
Cleaning activities
Cleaning the robot x Cleaning the IRB 1200 on page 149
Inspection activities
Inspecting the robot x Check for abnormal wear or contam-
ination.
For robots with protection type
Clean Room: Inspect daily
Inspecting the paint x Inspecting the robot paint on
page 119
Inspecting the robot cabling ii x iii Inspecting the robot cabling on
page 120
Inspecting the information labels x Inspecting the information labels
on page 121
Inspecting the axis-1 mechanical x iv Inspecting mechanical stops on
stop pin page 126
Inspecting the axis-2 mechanical x iv Inspecting mechanical stops on
stop page 126
Inspecting the axis-3 mechanical x iv Inspecting mechanical stops on
stop page 126
Inspecting the axis-4 mechanical -v
stop
Inspecting the timing belts x Inspecting timing belts on page 129
Replacement/changing activities
Every 36 months
Regularly i
hours
Replacing the battery pack vi Replacing the battery pack on
page 134
Replacing the axis-6 sealing set on x vii x vii Replacing the sealing set on tool
tool flange for Hygienic robots flange of Hygienic robots on
page 144
i "Regularly" implies that the activity is to be performed regularly, but the actual interval may not be
specified by the robot manufacturer. The interval depends on the operation cycle of the robot, its
working environment and movement pattern. Generally, the more contaminated environment, the
shorter intervals. The more demanding movement pattern (sharper bending cable harness), the
shorter intervals.
ii The robot cabling comprises the cabling between the robot and controller cabinet.
iii Replace when damage or cracks is detected or life limit is approaching.
iv Inspect immidiately if the mechanical stop is hit.
v Inspect immidiately if the mechanical stop is hit.
The robot needs to be disassembled according to section Replacing the axis-4 mechanical stop
on page 460 in order to get access to and inspect the mechanical stop.
vi The battery low alert (38213 Battery charge low) is displayed when remaining backup capacity
(robot powered off) is less than 2 months. Typical life of a new battery is 36 months if the robot is
powered off 2 days/week, or 18 months if the robot is powered off 16 hours/day. The life can be
extended (approximately 3 times) for longer production breaks by a battery shutdown service
routine. See the operating manual of the controller.
See the replacement instruction for more details.
vii Replace the sealing set every 12 months or every 60000 operating hours. The actual interval
depends on the operation cycle of the robot, its working environment and movement pattern.
Generally, the more contaminated environment, the shorter intervals. The more demanding
movement pattern (sharper bending cable harness), the shorter intervals.
Inspection activities
Inspecting the signal lamp x Inspecting the signal lamp
(option) on page 132
General
For robots with protection type Hygienic, there is a risk of surface corrosion or
paint peeling in case of mechanical damage to the coated surface. Therefore, it is
important to regularly inspect robot surfaces for any paint breaking or damage.
Action Description
1 Visually inspect the robot surface paint for
any paint breaking.
2 If there is paint breaking, clean the surface Use a lint free cloth.
so that it is free from oil and grease.
3 Use Touch up paint Clean Room/Hygienic, 3HAC036639-001
white to paint any damaged surfaces.
Note
Introduction
CAUTION
2 Visually inspect:
• the control cabling between the robot and
control cabinet
Look for abrasions, cuts or crush damage.
3 Replace the cabling if wear or damage is detected.
Location of labels
These figures show the location of the information labels to be inspected. The
symbols are described in section Safety symbols on manipulator labels on page 23.
Illustration 1 of 2
B
!
D
J
B
A
D B
FOOD GRADE
ABB Robotics Products AB LUBRICATION
TYPE LABEL
Barcodes/Streckkod
H G
B B
CP/CS connection
B B
IRB 1200-7/0.7
B B
CP/CS connection
B B
IRB 1200-5/0.9
Illustration 2 of 2
$%% B
!
$%%
A A B
B
D
F E
UL lable
Lifting
instruction Warning
lable
IRB 1200-0.5/9
C B
B B
B
SECTION A-A VIEW B
IRB 1200 Option
Description Illustration
A Calibration label
B Warning label
Flash
xx1300001091
C Instruction label
Lifting of robot
xx1400000518
D Warning label
Heat
!
3HAC 4431-1/06
xx1300001087
29454489-16
xx1700000984
E Instruction label
Brake release
Moving robot !
Brake release buttons
3HAC 2577-1/ 04
xx1400000519
F UL label
G Rating label
H Warning label
Tip risk when loosening bolts
3HAC 037277-001
xx1400000527
xx1600001074
xx1600001075
3 Maintenance
3.3.3 Inspecting the information labels
Continued
6XSSOHPHQWDU\GRFXPHQW 'RFW\SH 'RFXPHQW 'HVFULSWLRQ
K Type A label
7<3($
:HUHVHUYHDOOULJKWVLQWKLVGRFXPHQWDQGLQWKHLQ
GLVFORVXUHWRWKLUGSDUWLHVZLWKRXWH[SUHVVDXWKRULW\
+$&
IRUPDWLRQFRQWDLQHGWKHUHLQ5HSURGXFWLRQXVHRU
LVVWULFWO\IRUELGGHQ$%%&RS\ULJKW
xx1600002136
Type B label
7<3(% )RQW$ULDO
&RORXU3ODWLQXPOLNH
0DWHULDO3(70RUHTXLYDOHQW
:HUHVHUYHDOOULJKWVLQWKLVGRFXPHQWDQGLQWKHLQ
GLVFORVXUHWRWKLUGSDUWLHVZLWKRXWH[SUHVVDXWKRULW\
+$&
IRUPDWLRQFRQWDLQHGWKHUHLQ5HSURGXFWLRQXVHRU
6HOIDGKHVLYH
LVVWULFWO\IRUELGGHQ$%%&RS\ULJKW
xx1600002137 ⷦ⇢$ULDO
欫唁村摠唁
㧟㠨3(70RUHTXLYDOHQW
卛槱呹伧
/DWHVW5HYLVLRQ
)RQW$ULDO
0DWHULDO7\SH 'LPHQVLRQ
&RORXU3ODWLQXPOLNH6:' 'UDZLQJ
'HVFULSWLRQ
)/LDQJ
6WDWXV 5HVSRQVLEOH'HSDUWPHQW 1RRIVK
1HZ
www.abb.com/myABB.
0DWHULDO7\SH 'LPHQVLRQ 'HVFULSWLRQ 6:' 'UDZLQJ
Spare part Article number Note $SSURYHG
3UHSDUHG
7\SH%/DEHO 6KHHW
)/LDQJ
Labels and plate set 3HAC051417-001 6WDWXV
'052&150
1RRIVK
gienic.
(&21XPEHU 'RFXPHQWQR 5HYLQG
+$&
Inspecting, labels
Action Note
1
DANGER
Axis 1
xx1400000391
Axis 2
xx1400000389
Axis 3
xx1400000386
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Note
Introduction
CAUTION
Always read the section "General procedures" before doing any repair work.
Cut the paint or surface on the robot before replacing parts on page 158.
Axis 4
xx1400000036
Axis 5
xx1400000032
Equipment Note
Standard toolkit The content is defined in the section Stand-
ard toolkit on page 890.
Other tools and procedures may be required
if the spare part needs to be replaced. These
are specified in the replacement procedure.
Action Information
6 Check whether timing belts are slack
manually.
If the belt has no tension, adjust it!
xx1300000455
Action Note
2
DANGER
3 If the lamp is not lit, trace the fault by: Article number is specified in Re-
• inspecting whether the signal lamp is broken. quired tools and equipment on
If so, replace it. page 132.
• inspecting cable connections.
• inspecting the cabling. Replace the cabling if
a fault is detected.
Note
The battery low alert (38213 Battery charge low) is displayed when remaining
backup capacity (robot powered off) is less than 2 months. Typical life of a new
battery is 36 months if the robot is powered off 2 days/week, or 18 months if the
robot is powered off 16 hours/day. The life can be extended (approximately 3
times) for longer production breaks by a battery shutdown service routine. See
the operating manual for the robot controller.
xx1300002574
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
CAUTION
Always cut the paint with a knife and grind the paint edge when disassembling
parts. See Cut the paint or surface on the robot before replacing parts on page 158.
Required consumables
Consumable Article number Note
Cable straps -
Action Note
1 Decide which calibration routine to use, and take
actions accordingly prior to beginning the repair
procedure.
Action Note
2 Jog all axes to zero position. This is done in order to facilitate
updating of the revolution counter.
3
DANGER
4
CAUTION
2
ELECTROSTATIC DISCHARGE (ESD)
3
CAUTION
Action Note
4 Remove the connector cover attachment screws
on the lower arm and carefully open the cover.
CAUTION
CAUTION
xx1400000812
xx1700000004
Action Note
7 Valid for IRB 1200 Type B
Disconnect the connectors on the SMB unit.
• R1.ME1,2,4,5
• R1.ME3,6
• R2.SMB
xx1700000005
8 Disconnect the battery cable. Valid for IRB 1200 (no type spe-
cified) and IRB 1200 Type A
xx1300002571
xx1700000006
Action Note
9 Cut the cable strap that secures the battery and Valid for IRB 1200 (no type spe-
remove the battery. cified) and IRB 1200 Type A
Note
xx1300002579
xx1700000007
Action Note
2 For robots with protection type Clean Room:
For robots with food grade lubrication:
For robots with protection type Hygienic:
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
3 Fit the battery and and secure it with a cable strap. Valid for IRB 1200 (no type spe-
cified) and IRB 1200 Type A
Note
xx1300002579
xx1700000007
Action Note
4 Connect the battery cable. Valid for IRB 1200 (no type spe-
cified) and IRB 1200 Type A
xx1300002571
xx1700000006
WARNING
Action Note
6 Valid for IRB 1200 Type B
Connect the connectors to the SMB unit.
• R1.ME1,2,4,5
• R1.ME3,6
• R2.SMB
WARNING
xx1700000005
xx1700000004
8 Refit the EIB/SMB cover to the lower arm with the Screws: 3HAB3409-207 (M3x8).
attachment screws. Tightening torque: 1.5 Nm
xx1300002427
Note
Concluding procedure
Action Note
1 Update the revolution counters. See Updating revolution counters on
page 813.
2 For robots with protection type Clean
Room:
For robots with food grade lubrication:
For robots with protection type Hygienic:
Clean, seal and paint the joints that have
been opened. See Cut the paint or surface
on the robot before replacing parts on
page 158.
Note
3
DANGER
General
To ensure the sealing efficiency, sealing parts on the tool flange of Hygienic robots
is recommended to be replaced at an interval of 12 months or 60000 operating
hours.
xx2100001485
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Grease 3HAC070875-001 Molykote P1900
For robots with protection type
Hygienic
CAUTION
Always cut the paint with a knife and grind the paint edge when disassembling
parts. See Cut the paint or surface on the robot before replacing parts on page 158.
Action Note
2 Remove the screws and washers.
xx2100001449
xx2100001450
xx2100001451
4 Place the flange tightening tool together with a Flange tightening tool:
3/8" (10 mm) socket spanner on the seal ring unit 3HAC079686-001
and loosen the unit.
xx2100001452
xx2100001453
Action Note
6 Replace the parts with new ones.
7 Apply a little grease to the screw thread. Grease: Molykote P1900
xx2100001454
xx2100001453
xx2100001455
9 Place the flange tightening tool together with a Flange tightening tool:
3/8" (10 mm) socket spanner on the seal ring unit 3HAC079686-001
and tighten the unit. Tightening torque: 8 Nm
xx2100001456
Action Note
10 Fit two guide pins to the tool flange. Guide pin for stainless shaft on tool
flange: 3HAC079684-001
xx2100001457
xx2100001458
xx2100001459
xx2100001460
DANGER
General
To secure high uptime it is important that the IRB 1200 is cleaned regularly. The
frequency of cleaning depends on the environment in which the product works.
Different cleaning methods are allowed depending on the type of protection of the
IRB 1200.
Note
Cleaning methods
The following table defines what cleaning methods are allowed depending on the
protection type.
Protection Cleaning method
type
Vacuum Wipe with cloth Rinse with water High pressure water or
cleaner steam
Standard Yes Yes. With light No No
IP40 cleaning deter-
gent.
Cables
Movable cables need to be able to move freely:
• Remove waste material, such as sand, dust and chips, if it prevents cable
movement.
• Clean the cables if they have a crusty surface, for example from dry release
agents.
Overview
Hygienic robots are designed with special sealings and coatings. The axis-6 tool
flange is also equipped with stainless steel sealing set. These special designs
allow the Hygienic robots to be wiped down or washed down using corresponding
proper detergents according to actual working environments and applications.
Cleaning methods also vary according to the to-be-cleaned surfaces and parts of
the IRB 1200 with protection type Hygienic. Always use the proper cleaning method
according to the actual applications and strictly follow the cleaning procedure.
xx2100001401
A User tools
B Wipe down area The robot body without any protection should use
the wipe down method for cleaning. If the robot
body is properly covered by protective device or
equipment, the wash down method is also applic-
able.
C Wash down area In most cases, the tool flange surface should use
the wash down method for cleaning. Users can
also perform wipe down cleaning on this part ac-
cording to their applications.
Required equipment
Equipment Note
High pressure washer
Lint free cloth
Usable detergents
Always use the recommended detergents listed in previous table for cleaning the
IRB 1200 with protection type Hygienic. Contact ABB if using any disinfectants
and detergents other than the listed ones before conducting cleaning activities.
The following list defines the prerequisites:
• Read the material safety data sheet (MSDS) before using any chemicals.
• Always use proper protective equipment like gloves, goggles, safety boots,
face shields and apron when using chemicals.
Cleaning instructions
DANGER
Turn off all electrical power, hydraulic and pneumatic pressure supplies before
entering the workspace of the manipulator.
Also read the safety sections:
• Pneumatic or hydraulic related hazards on page 32
• Electrical safety on page 31
• Maintenance and repair on page 34
Action Note
1 Before cleaning,
• Use protective devices and equipment to
make sure the painted surfaces of the robot
body (wipe down areas) not exposed dir-
ectly to sprayed detergents, disinfectants
and ejected water.
• If user tools are removed from the robot
flange before the cleaning, conduct protect-
ive measures on screw holes to make sure
no intrusion of soils, water, detergents and
disinfectants into the holes during cleaning.
xx2100001402
A User tools
B Protective devices or equip-
ment
C Wipe down area
2 Pre-rinse with water for removal of food residues Recommended water temperature:
from to-be-cleaned areas. 40 - 60°C
Make sure no visible residues left.
3 Foam the surface with detergent Topax66 or To- • Detergent: Topax66, concen-
paz HD 1. tration (v/v) 2 %
Use a sprinkling can so that the to-be-cleaned • Detergent: Topaz HD1, con-
areas can be covered evenly with sufficient foamy centration (v/v) 2 %
detergent.
4 Wait 15 minutes.
Let the detergent work for approx 15 minutes to
retain effective cleaning properties.
Ensure that the cleaning agent does not dry on
the surface.
5 Rinse thoroughly with water to remove the deter- Recommended water temperature:
gent. 40 - 60°C
6 Foam the surface with detergent Topaz AC3. Detergent: Topaz AC3, concentra-
Use a sprinkling can so that the to-be-cleaned tion (v/v) 2 %
areas can be covered evenly with sufficient foamy
detergent.
7 Wait 15 minutes.
Let the detergent work for approx 15 minutes to
retain effective cleaning properties.
Ensure that the cleaning agent does not dry on
the surface.
8 Rinse thoroughly with water to remove the deter- Recommended water temperature:
gent. 40 - 60°C
9 Foam the surface with disinfection Topactive DES. Detergent: Topactive DES, concen-
Use a sprinkling can so that the to-be-cleaned tration (v/v) 2 %
areas can be covered evenly with sufficient foamy
disinfection.
10 Wait 15 minutes.
Action Note
11 Rinse thoroughly with water to remove the disin- Water temperature: ambient
fection.
12 Wipe the surface dry with lint free cloth.
13 If user tools are removed from the robot flange
before the cleaning, then, after cleaning,
• Make sure no residues left on the tool
flange or screw holes before reinstall the
tools or any other accessories to the flange.
Action Note
1 Before cleaning,
• Make sure no spraying or ejecting of any
detergents, disinfectants and water to the
robot surfaces during the cleaning.
2 Use the lint free cloth to remove soils or any other
contaminant from the to-be-cleaned surfaces.
Make sure no visible residues left.
3 Spray disinfectant DRYSAN TM DUO on robot Disinfectant: DRYSAN TM DUO,
surfaces. concentration (v/v) 100 %
4 Wait 2-3 minutes for disinfectant volatilization and
then wipe the robot with lint free cloth.
4 Repair
4.1 Introduction
WARNING
Repair activities not described in this chapter must only be carried out by ABB.
Note
When replacing a part on the IRB 1200, report to your local ABB the serial number,
the article number, and the revision of both the replaced unit and the replacement
unit.
This is particularly important for safety equipment to maintain the safety integrity
of the installation.
Safety information
Make sure to read through the chapter Safety on page 19 before commencing any
service work.
Note
If the IRB 1200 is connected to power, always make sure that the IRB 1200 is
connected to protective earth and a residual current device (RCD) before starting
any repair work.
For more information see:
• Product manual - OmniCore C30
• Product manual - OmniCore C90XT
• Product manual - OmniCore E10
• Product manual - IRC5
• Product manual - IRC5 Compact
4.2.1 Cut the paint or surface on the robot before replacing parts
General
Follow the procedures in this section whenever breaking the paint of the robot
during replacement of parts.
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
When replacing parts on the robot, it is important to make sure that after the
replacement, no particles will be emitted from the joint between the structure and
the new part, and that the easy cleaned surface is retained.
Required equipment
Removing
Action Description
1 Cut the paint with a knife in the joint between
the part that will be removed and the struc-
ture, to avoid that the paint cracks.
xx0900000121
Refitting
Note
Refitting is required only for robots with protection type Clean Room, with food
grade lubrication and with protection type Hygienic.
Action Description
1 Before the parts are refitted, clean the joint Use ethanol on a lint free cloth.
so that it is free from oil and grease.
2 Place the tooling pin in hot water.
3 Seal all refitted joints with sealing compound.
xx0900000122
xx0900000125
5 For robots with protection type Clean Room For robots with protection type Clean
For robots with food grade lubrication Room
Wait 10 minutes. For robots with food grade lubrication
For robots with protection type Hygienic Sikaflex 521FC skin dry time (10 minutes).
Wait 40 minutes. For robots with protection type Hygienic
Trans Clear skin dry time (40 minutes).
6 Use Touch up paint Clean Room/Hygienic, 3HAC036639-001
white to paint any damaged surfaces.
Note
Note
After all repair work, wipe the robot free from particles with spirit on a lint free
cloth.
General
This section describes how to mount different types of sealings.
Equipment
Rotating sealings
The procedure below describes how to fit rotating sealings.
CAUTION
Action Note
1 Check the sealing to ensure that:
• The sealing is of the correct type.
• There is no damage on the main lip.
2 Inspect the shaft surface before mounting. If scratches
or damage are found, the shaft must be replaced since
it may result in future leakage. Do not try to grind or
polish the shaft surface to get rid of the defect.
Action Note
3 Lubricate the sealing with grease just before fitting. Article number is specified in
(Not too early - there is a risk of dirt and foreign Equipment on page 161.
particles adhering to the sealing.)
Fill 2/3 of the space between the dust lip and the main
lip with grease. If the sealing is without dust lip, just
lubricate the main lip with a thin layer of grease.
A B C
xx2000000071
A Main lip
B Grease
C Dust lip
4 Mount the sealing correctly with a mounting tool. A
Never hammer directly on the sealing as this may
result in leakage.
xx2000000072
A Gap
5 Make sure that no grease is left on the robot surface.
O-rings
The following procedure describes how to fit o-rings.
Action Note
1 Ensure that the correct o-ring size is used.
2 Check the o-ring for surface defects, burrs, Defective o-rings, including damaged
shape accuracy, or deformation. or deformed o-rings, may not be used.
3 Check the o-ring grooves.
The grooves must be geometrically correct and
should be free of pores and contamination.
4 Lubricate the o-ring with grease.
5 Tighten the screws evenly while assembling.
6 Check that the o-ring is not squashed outside
the o-ring groove.
7 Make sure that no grease is left on the robot
surface.
4.2.4 Swing sealing plug for Clean Room, food grade lubrication and Hygienic robots
xx1600000264
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Sealant 3HAC026759-001 Sikaflex 521FC
For robots with protection type
Clean Room
For robots with food grade lubric-
ation
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
Action Note
1 Cut the swing sealing plug through with a sharp
object to get access to the screws.
xx1600000206
xx1600000207
Action Note
3 Detach the swing sealing plug from the cable
housing cover.
xx1600000208
Action Note
1 Mask the gap between the swing and the base.
xx1600000209
2 Apply a string of the sealant to the joint of the For robots with protection type
swing cable housing cover. Clean Room
For robots with food grade lubric-
ation
Sealant, Sikaflex 521FC
For robots with protection type
Hygienic
Sealant, Trans Clear
xx1600000210
Action Note
4 Wait for the sealant to dry and then remove the Sikaflex 521FC skin dry time: 10
mask. minutes
Trans Clear skin dry time: 40
minutes
5 Apply a little sealant to the inner surface of the For robots with protection type
swing sealing plug. Clean Room
For robots with food grade lubric-
ation
Sealant, Sikaflex 521FC
For robots with protection type
Hygienic
Sealant, Trans Clear
xx1600000211
xx1600000261
xx1600000212
xx1600000213
xx1300002414
xx1400000410
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Manipulator cable harness 3HAC061287-001 Used for IRB 1200 Type B. See
without Ethernet (rear interface), Type B of IRB 1200 on page 873.
Clean Room and SafeMove Used with protection type Clean
2-supported Room.
Manipulator cable harness Used for robots with food grade
without Ethernet (rear interface), lubrication.
food grade lubrication and
SafeMove 2-supported Used with protection type Hy-
gienic.
Manipulator cable harness
without Ethernet (rear interface), With connector interface at rear
Hygienic of the base.
Manipulator cable harness with 3HAC061284-001 Used for IRB 1200 Type B. See
Ethernet (bottom interface), Type B of IRB 1200 on page 873.
SafeMove 2-supported Used with protection type Hy-
Manipulator cable harness with gienic.
Ethernet (bottom interface), Hy- With connector interface at bot-
gienic. tom of the base.
Manipulator cable harness 3HAC061285-001 Used for IRB 1200 Type B. See
without Ethernet (bottom inter- Type B of IRB 1200 on page 873.
face), SafeMove 2-supported Used with protection type Hy-
Manipulator cable harness gienic.
without Ethernet (bottom inter- With connector interface at bot-
face), Hygienic. tom of the base.
Required consumables
Equipment Article number Note
Cable straps -
Grease 3HAC042536-001 Used for lubrication of cable con-
tact areas.
Grease 3HAC029132-001 Used for lubrication of cable con-
tact areas for robots with food
grade lubrication and robots in
protection type Hygienic.
Locking liquid 3HAB7116-1 Loctite 243
Cleaning agent - Loctite 7063
Flange sealing 12340011-116 Loctite 574
For robots with protection type
Clean Room.
For robots with food grade lubric-
ation.
Sealant 3HAC026759-001 Sikaflex 521FC
For robots with protection type
Clean Room.
For robots with food grade lubric-
ation.
For robots with protection class
IP67.
For robots with protection type
Foundry Plus.
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
xx1300002581
Action Note
3
DANGER
4
CAUTION
2
CAUTION
Action Note
3 Remove the covers on each side of the wrist by
removing their screws.
For robots with protection class
Note IP67
For robots with protection type
For robots with protection class IP67 Foundry Plus
For robots with protection type Foundry Plus
The two front screws on the left hand side cover
(encircled in the figure) have been fitted with
locking liquid.
The tubular cover (left hand side cover) has two
extra screws and washers, as encircled in the
figure.
xx1300002349
xx1600001148
xx2100001406
Action Note
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
Action Note
3 Snap loose and disconnect the axis-5 FPC
connectors.
xx1300002390
2
CAUTION
xx1400000738
xx1500000252
2
CAUTION
xx1300002400
xx1300002413
Action Note
5 Pull out the FPC connectors from the housing and Cable layout in IRB 1200-7/0.7 :
disconnect them.
xx1300002412
xx1400001471
xx1300002398
Action Note
7 Disconnect the remaining FPC connectors.
xx1300002399
2
CAUTION
CAUTION
xx1300000456
Action Note
4 Cut the strap that holds the connectors.
xx1300002494
Tip
xx1300002495
2
CAUTION
Action Note
3 Pull out the axis-3 motor connectors from the
housing and disconnect them.
xx1300002420
2
CAUTION
xx1300002422
Action Note
4 Remove the screws that fasten the fix sheet to
the inner plastic guide.
xx1300002421
xx1300002423
CAUTION
xx1300002424
Action Note
2
ELECTROSTATIC DISCHARGE (ESD)
3
CAUTION
CAUTION
CAUTION
xx1300002428
Action Note
7 Valid for IRB 1200 Type B
Loose the connector screws.
xx1700000004
xx1700000005
2
CAUTION
Action Note
4 Remove the fix sheet attachment screws in the
lower arm.
xx1300002426
CAUTION
xx1400001130
xx1600000205
Action Note
8 Remove the swing cable housing cover by remov-
ing the screws.
xx1300002431
xx1400001528
xx1300002432
Action Note
11 Pull out the cabling and then remove the axis-2
motor bracket from the cable package by remov-
ing the screws.
CAUTION
xx1300002433
xx1300002434
xx1300002435
Action Note
14 Remove the axis-2 sealing ring by removing the
screws.
xx1400000020
Tip
xx1400000023
Action Note
1
DANGER
2
CAUTION
Action Note
3
CAUTION
CAUTION
xx1400000679
5
WARNING
6
CAUTION
Action Note
7 Loosen the robot from the foundation by
removing the foundation attachment
screws and put the robot on its side.
xx1400000680
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the bottom cover. Rear connector interface:
xx1300000469
xx1400000403
Action Note
4 Remove the axis-1 motor bracket. Rear connector interface:
xx1300000470
xx1400000404
xx1300002496
2
CAUTION
Tip
xx1300000467
xx1300000471
Action Note
5 Pull out the base slightly and turn it aside.
Tip
xx1300000472
Action Note
1
DANGER
2
CAUTION
xx1300002438
Action Note
5 Remove the cable bracket from the cabling, if the
cable package is to be replaced with a new spare
part.
xx1300002446
2
CAUTION
xx1300002448
Action Note
5 Pull the cable package out from the base, through
the rear.
xx1300002456
2
CAUTION
xx1400000405
Action Note
6 Remove the cable bracket by removing the
screws.
xx1400000406
xx1400000407
xx1400000411
Action Note
2 Valid for IRB 1200-7/0.7
If the cable harness is a new spare part, cut off
100 mm length of each air hose at the upper end.
Note
xx1400000741
Action Note
5 Refit the base cover with the attachment screws. Screws: 3HAB3409-212 (M4x16).
Tightening torque: 4 Nm.
xx1300002448
Note
xx1400000480
Action Note
3 Refit the bracket inside the base with the screws. Tightening torque: 1.5 Nm.
xx1400000407
4 Refit the cable bracket with the screws. Tightening torque: 1.5 Nm.
xx1400000406
5 For robots with protection class IP67 Gasket for rear base cover:
For robots with protection type Foundry Plus 3HAC058566-001 (not Hygienic
robots) / 3HAC080710-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the base cover.
Replace if damaged.
xx1400000413
Action Note
8 Refit the base cover. Screws: 3HAB3409-212 (M4x16).
Tightening torque: 4 Nm.
xx1400000405
Note
xx1400000480
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 Check the axis-1 sealing ring. Axis-1 sealing ring: 3HAC044676-
Replace if damaged. 001 / 3HAC068107-001 i
xx1600001125
Action Note
4 For robots with protection class IP67 On axis-1 sealing ring version
On axis-1 sealing ring version 3HAC044676-001, 3HAC044676-001:
3HAC058568-001 or 3HAC068107-001: Axis-1 sealing ring gasket:
For robots with protection type Foundry Plus 3HAC045685-001
On axis-1 sealing ring version 3HAC058568-001
or 3HAC068107-001:
Check the gasket on the axis-1 sealing ring.
(See Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.)
Replace if damaged.
xx1400000458
xx1600001149
xx1900001735
Action Note
5 For robots with protection class IP67 V-ring: 3HAB3732-34
On axis-1 sealing ring version 3HAC056658-001, On axis-1 sealing ring version
3HAC058568-001 or 3HAC068107-001: 3HAC056658-001:
For robots with protection type Foundry Plus
On axis-1 sealing ring version 3HAC058568-001
or 3HAC068107-001:
Check the V-ring on the axis-1 sealing ring.
(See Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.)
Replace if damaged. xx1600001124
xx1600001150
xx1900001736
6 Check the cable protection on the axis-1 sealing Cable protection: 3HAC044691-001
ring. Torx countersunk head screw
Replace if damaged. M3x5: 3HAC14286-4
If replacing the cable protection, use locking liquid Tightening torque: 0.3 Nm
Loctite 243 on the screws.
xx1400000456
7 Refit the cable bracket to the cabling, if removed. Tightening torque: 1 Nm.
Use Loctite 243 on the screw threads.
xx1300002446
Action Note
8 Refit the axis-1 sealing ring to the swing and Tightening torque: 1.5 Nm.
carefully run the cabling into the swing.
xx1300002438
i For information on which sealing ring to be ordered, see Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check the axis-1 radial sealing in the base. Radial sealing with dust lip: 3HAB3701-47
Replace if damaged. M2 variseal sealing: 3HAC044641-002
Note
CAUTION
Action Note
3 For robots with protection class IP67 Grease: 3HAC058065-001.
For robots with protection type Foundry
Plus
Apply grease to the radial sealing surface.
xx1600000170
4 Fit the guide pins to the drive unit. Guide pin for axis-1 gear unit:
3HAC049703-001
xx1300002566
CAUTION
Action Note
6 Secure with attachment screws and wash- Screws: 3HAB3409-52 (M10x35).
ers, but do not tighten yet.
xx1300002567
Note
xx1300000523
Action Note
9 For robots with protection class IP67 Gasket on top swing cover
For robots with protection type Foundry 3HAC056696-001 (not Hygienic robots) /
Plus 3HAC080698-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000425
10 Refit the swing top cover with the screws. Cover on top of swing: 3HAC059679-001
Replace if damaged. Cover on top of swing, Clean Room
Cover on top of swing, food grade lubrica-
tion
Cover on top of swing, Hygienic
: 3HAC056133-001
Screws: 3HAB3409-209 (M3x20).
Tightening torque: 1.5 Nm.
xx1300000467
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Reconnect the connectors and secure the
connectors to the bracket with cable straps.
xx1300002496
Action Note
3 Refit the axis-1 motor bracket. Tightening torque: 1.5 Nm.
Rear connector interface:
xx1300000470
xx1400000404
xx1400000412
Action Note
5 Refit the bottom cover. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
Rear connector interface:
xx1300000469
xx1400000403
Note
Action Note
2
CAUTION
xx1500000241
4 Raise the robot to standing and secure Attachment screws: M12x35 (robot installation
to the foundation with the attachment directly on foundation), quality: 8.8.
screws and washers. Washers: 13 x 20 x 2, steel hardness class
300HV.
Pin: 2 pcs, D6x20, ISO 2338 - 6m6x20 - A1.
Tightening Torque: 55 Nm ± 5 Nm.
Action Note
2 Check the axis-2 sealing ring. Axis-2 sealing ring: 3HAC044677-
For robots with protection class IP67 001
For robots with protection type Foundry Plus Gasket of axis-2 sealing ring:
3HAC045688-001 (not Hygienic
For robots with protection type Clean Room robots) / 3HAC080697-001 (Hygien-
For robots with food grade lubrication ic robots)
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000476
xx1400000457
Action Note
4 Fetch the cable housing, the plastic plate and the
axis-2 sealing ring and run the cable package
through them.
xx1400000025
5 Fasten the plastic plate to the cable housing, if The plastic plate is included in:
removed. Cable harness material set:
Replace if damaged. 3HAC049663-001.
xx1400000023
Action Note
6 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-
For robots with protection type Foundry Plus 004
Check the sealing.
Replace if damaged.
CAUTION
xx1400000454
Action Note
7 For robots with protection class IP67 Radial sealing with dust lip:
For robots with protection type Foundry Plus 3HAB3701-41
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the radial sealing.
Replace if damaged.
Note
xx1400000753
Tip
9 Refit the axis-2 sealing ring with the screws. Tightening torque: 1.5 Nm.
xx1400000020
Action Note
10 Refit the cable housing with the screws. Screws: 3HAB3409-236 (M4x10).
Tightening torque: 3 Nm.
xx1300002435
Note
xx1400000481
Action Note
12 Reconnect the motor connectors.
• R2.ME2
• R2.MP2
xx1300002434
13 Refit the axis-2 motor bracket to the cable pack- Tightening torque: 1.5 Nm.
age with the two screws.
CAUTION
xx1400000021
xx1300002432
Action Note
15 Secure the connector R2.MP2 and its cable with
cable straps onto the motor bracket. Make sure
the connector is fixed by its tab to the bracket.
xx1400001529
xx1400000482
Action Note
18 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056726-001 (not Hygienic
robots) / 3HAC080704-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000424
Action Note
21 Refit the cable housing cover. Cable housing cover of the swing:
Replace if damaged. 3HAC059678-001
Cable housing cover of the swing,
Note Clean Room
Cable housing cover of the swing,
Remember to refit the two lower screws shown food grade lubrication
in the figure. Cable housing cover of the swing,
Hygienic
: 3HAC056214-001
Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
xx1300002431
Note
22 For robots with protection type Foundry Plus Protection plug for lifting holes:
Check the protection plugs for lifting holes. 3HAC4836-24
Replace if damaged.
xx1600001151
Action Note
23 For robots with protection type Clean Room Swing sealing plug:3HAC053687-
For robots with food grade lubrication 001
For robots with protection type Hygienic
Refit the swing sealing plug.
Follow the procedure specified in Refitting the
swing sealing plug on page 167.
xx1600000205
24 Refit the lower arm bracket to the cable package. Tightening torque: 1.5 Nm.
CAUTION
xx1300002430
Action Note
3 For robots with protection class IP67 Gasket on EIB/SMB cover:
For robots with protection type Foundry Plus 3HAC056728-001 (not Hygienic
robots) / 3HAC080706-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the EIB/SMB cover gasket.
Replace if damaged.
xx1400000475
WARNING
5 Valid for IRB 1200 (no type specified) and IRB xx1300002428
1200 Type A
Connect the lugs to the EIB/SMB cover.
6 Valid for IRB 1200 Type B
Connect the connectors to the SMB unit.
• R1.ME1,2,4,5
• R1.ME3,6
• R2.SMB
WARNING
xx1700000005
Action Note
7 Valid for IRB 1200 Type B Tightening torque: 0.3 Nm
Tighten the connector screws.
xx1700000004
8 Refit the EIB/SMB cover to the lower arm with the Screws: 3HAB3409-207 (M3x8).
attachment screws. Tightening torque: 1.5 Nm
xx1300002427
Note
Action Note
9 Refit the fix sheet attachment screws in the lower Tightening torque: 1.5 Nm.
arm.
xx1300002426
xx1400000483
Action Note
3 Guide the cable package into the upper arm,
through the housing.
Note
4 Refit the bracket to the sheet with two screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300002424
5 Refit the fix sheet to the motor. Tightening torque: 1.5 Nm.
xx1300002423
Action Note
6 Refit the fix sheet to the inner plastic guide. Tightening torque: 1.5 Nm.
xx1300002421
7 Fit the air hose holder to the bracket. Air hose holders are included in
Replace the holder, if damaged. Cable harness material set
(3HAC049663-001).
Tightening torque: 4 Nm.
Tip
xx1300002422
xx1400001133
xx1300002420
Action Note
9 Apply grease to the cable package, cover all
moving area of the package.
xx1400000754
xx1300002371
Action Note
3 Secure the connectors to the motor with a cable
strap.
xx1300002494
Tip
xx1300002399
Action Note
3 Reconnect the FPC connectors and push them Cable layout in IRB 1200-7/0.7 :
into place inside the housing.
Tip
xx1300002412
xx1400001471
Action Note
5 For robots with protection class IP67
For robots with protection type Foundry Plus
Apply flange sealing Sikaflex 521FC on the
mounting surfaces of the small cover on the
housing.
6 Refit the small cover to the housing.
Replace if damaged.
xx1300002398
xx1600000214
Action Note
8 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
9 Check the PTFE film on the cable housing. PTFE film on lower arm cable
Replace if damaged. housing: 3HAC044710-001
xx1400000740
Action Note
10 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056724-001 (not Hygienic
robots) / 3HAC080702-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication PTFE film on cable housing cover:
For robots with protection type Hygienic 3HAC044660-001
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000048
Action Note
13 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the screws
securing the cover.
xx1300002400
Note
Connecting the air hoses and CP/CS cabling on robots not in protection type Hygienic
Use this procedure if the robot is not in protection type Hygienic.
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 Reconnect the air hoses. Air connector set with Ethernet
Replace the air hose connector set if damaged. hole in flange: 3HAC049664-001
Air connector set without Ethernet
hole in flange: 3HAC049665-001
xx1400000738
Action Note
3 If equipped, reconnect the CP/CS connector.
For robots with protection class IP67
For robots with protection type Foundry Plus
1 Check the gasket.
2 Replace if damaged.
For robots with protection type Clean Room
For robots with food grade lubrication
1 Remove residual locking liquid and other xx1500000252
pollutants with cleaning agent Loctite 7063.
On robots with protection class
2 Apply flange sealing Loctite 574 on the IP67
mounting surfaces of the CP/CS connector
and wipe clean if there is any overflowing On robots with protection type
Loctite 574. Foundry Plus
Gasket: 3HAC058567-001
xx1500000251
4 For robots with protection type Foundry Plus Protection bracket for CP/CS con-
If required, fit the protection bracket for CP/CS nectors: 3HAC058350-001
connectors.
xx1600001152
Connecting the air hoses and CP/CS cabling on robots in protection type Hygienic
Use this procedure if the robot is with protection type Hygienic.
Action Note
1 Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
Action Note
2 If the Hygienic robot not equipped with air hoses Plate without connector set:
and CP/CS cabling: 3HAC078810-001
Check the plate without connector set and the at- Gasket: 3HAC078804-001
tached gasket.
Replace if damaged.
xx2100001433
xx1400000738
xx1500000252
5 Check the connectors on the plate with connector Plate with connector set:
set and the attached gasket. 3HAC079691-001
Replace if damaged. Gasket: 3HAC078804-001
xx2100001434
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
Concluding procedure
Action Note
1 For robots with protection class IP67 Housing cover gasket (IRB 1200-7/0.7 ):
For robots with protection type Foundry 3HAC056698-001 (not Hygienic robots) /
Plus 3HAC080700-001 (Hygienic robots)
For robots with protection type Clean Housing cover gasket (IRB 1200-5/0.9 ):
Room 3HAC056697-001 (not Hygienic robots) /
3HAC080699-001 (Hygienic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000477
2 Refit the upper arm housing cover with the Screws: 3HAB3409-207 (M3x8).
screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300000456
Note
Action Note
3 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the upper arm housing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000215
Note
4.3.2 Replacing the axis-4 FPC unit, housing extender unit and housing extender
sealings
xx1300002419
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
3
DANGER
4
CAUTION
2
CAUTION
Action Note
3 Remove the covers on each side of the wrist by
removing their screws.
For robots with protection class
Note IP67
For robots with protection type
For robots with protection class IP67 Foundry Plus
For robots with protection type Foundry Plus
The two front screws on the left hand side cover
(encircled in the figure) have been fitted with
locking liquid.
The tubular cover (left hand side cover) has two
extra screws and washers, as encircled in the
figure.
xx1300002349
xx1600001148
xx2100001406
Action Note
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
xx1300002350
Action Note
4 Remove the timing belt.
xx1300002351
xx1300002390
xx1300002352
Action Note
2
CAUTION
xx1300002353
xx1300002355
xx1300002356
Action Note
6 Guide the hoses through the plate hole and re-
move the plate.
xx1300002357
xx1300002358
CAUTION xx1300002359
xx1300002611
2
CAUTION
xx1300002400
xx1300002413
Action Note
5 Pull out the FPC connectors from the housing and Cable layout in IRB 1200-7/0.7 :
disconnect them.
xx1300002412
xx1400001471
xx1300002398
Action Note
7 Disconnect the remaining FPC connectors.
xx1300002399
2
CAUTION
xx1300002373
xx1600000262
Action Note
5 Remove the extender unit screws.
xx1300002372
xx1300002374
2
CAUTION
xx1300002415
Action Note
1
DANGER
2
CAUTION
CAUTION
xx1300002417
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-007
For robots with protection type Foundry
Plus
Check the sealing.
Replace if damaged.
CAUTION
xx1300002418
3 For robots with protection class IP67 Radial sealing with dust lip: 3HAB3701-48
For robots with protection type Foundry
Plus
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the radial sealing.
Replace if damaged, as described below.
In order to replace the radial sealing, both
the axis-4 mechanical stop and the axis-4
FPC unit must be removed from the hous-
ing extender unit, if not already removed.
xx1400000438
Action Note
6 Fit the circular part of the radial sealing Axis-4 sealing assembly tool set:
assembly tool against the radial sealing. 3HAC049699-001
7 Fit the tool plate to the other side of the
housing extender unit with the six screws
M6X50.
xx1400000436
xx1400000437
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Refit the FPC unit to the housing extender Tightening torque: 0.5 Nm.
unit and secure with the screws.
CAUTION
CAUTION
xx1300002611
xx1300002613
Action Note
3 For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Make sure the four cavities are fully filled with
glue. If not, fill glue again before the refitting.
xx1600000216
CAUTION
Note
xx1300002372
6 For robots with protection type Foundry Plus Screw sealing plug: 3HAC053685-
For robots with protection type Clean Room 001
For robots with food grade lubrication
For robots with protection type Hygienic
Press in screw sealing plugs to cover the screws.
xx1600000263
Action Note
7 Fit and secure the axis-4 FPC unit screws. Tightening torque: 0.3 Nm.
xx1300002373
Tip
xx1300002399
Action Note
3 Reconnect the FPC connectors and push them Cable layout in IRB 1200-7/0.7 :
into place inside the housing.
Tip
xx1300002412
xx1400001471
Action Note
5 For robots with protection class IP67
For robots with protection type Foundry Plus
Apply flange sealing Sikaflex 521FC on the
mounting surfaces of the small cover on the
housing.
6 Refit the small cover to the housing.
Replace if damaged.
xx1300002398
xx1600000214
Action Note
8 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
9 Check the PTFE film on the cable housing. PTFE film on lower arm cable
Replace if damaged. housing: 3HAC044710-001
xx1400000740
Action Note
10 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056724-001 (not Hygienic
robots) / 3HAC080702-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication PTFE film on cable housing cover:
For robots with protection type Hygienic 3HAC044660-001
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000048
Action Note
13 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the screws
securing the cover.
xx1300002400
Note
Action Note
2 Put the connectors and air hoses into the wrist
carefully while at the same time refitting the wrist
to the housing extender unit.
Be careful not to damage the FPC cabling and the
connectors.
CAUTION xx1300002359
xx1300002611
3 Refit the washer while at the same time putting Washer: 3HAC044869-001
the cables through its center.
Replace washer, if damaged.
xx1400000001
Action Note
4 Refit the screw M6x35 (1 pc). Do not tighten yet. Screw: 3HAB3409-238 (M6x35 (1
pc)).
xx1400000002
Note
5 Refit the rest of the screws (M5x35 (7 pcs)). Screw: 3HAB3409-237 (M5x35 (7
pcs)).
xx1400000003
Note
xx1300002356
Action Note
8 Reconnect the air hoses.
CAUTION
xx1300002355
xx1300002353
xx1300002463
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the timing belt on the pulley.
xx1300002351
xx1300002350
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
Concluding procedure
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean, seal and paint the joints that have
been opened. See Cut the paint or surface
on the robot before replacing parts on
page 158.
Note
xx1300002397
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Action Note
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
xx1300002581
3
DANGER
Action Note
4
CAUTION
xx1300002389
2
CAUTION
xx1300002390
Action Note
4 Remove the connector plate by first removing the
screws.
xx1300002391
Note
xx1300002392
2
CAUTION
xx1300002393
Action Note
4 Remove the sleeve by screwing in two of the
screws into the press out holes to force the sleeve
out.
xx1300002582
xx1300002394
xx1300002395
Action Note
1
WARNING
Action Note
2 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
3 Reconnect the axis-6 motor connectors to
the FPC unit.
xx1300002395
4 Carefully refit the FPC unit and secure with Tightening torque: 0.3 Nm.
screws.
Note
xx1300002394
Action Note
5 For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
For robots with protection type Hygienic Flange sealing, Loctite 574
Remove residual locking liquid and other For robots with protection type Hygienic
pollutants with cleaning agent Loctite 7063. Flange sealing, Trans Clear
Apply flange sealing on the mounting sur-
faces of the sleeve.
Note
xx1300002609
xx1300002393
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Check the sealing. M2 variseal sealing: 3HAC044641-009
Replace if damaged.
CAUTION
xx1300002396
xx1300002608
xx1400000485
Action Note
8 Screw the screws, little by little, to press
the sealing into place.
xx1400000486
xx1300002610
Action Note
3 Refit the tubular cable housing with the screws. Tightening torque: 1.5 Nm.
Tubular cable housing:
3HAC059695-001
Tubular cable housing, Clean
Room
Tubular cable housing, food grade
lubrication
: 3HAC056143-001
Tubular cable housing, Hygienic:
3HAC079692-001
xx1300002392
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the connector plate and secure with Tightening torque: 0.3 Nm.
the M3 screws.
xx1400001401
Action Note
3 Secure the three M2.5 screws. Tightening torque: 0.3 Nm.
xx1400001402
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
xx1300002389
Note
Concluding procedure
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean, seal and paint the joints that have
been opened. See Cut the paint or surface
on the robot before replacing parts on
page 158.
Note
Note
The EIB unit is used for IRB 1200 no type specified and IRB 1200 Type A.
The SMB unit is used for IRB 1200 Type B.
xx1300002574
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Equipment Article number Note
Locking liquid 3HAB7116-1 Loctite 243
Action Note
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
1 Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.
2 Jog all axes to zero position.
xx1300002581
3
DANGER
Action Note
4
CAUTION
xx1300002400
2
ELECTROSTATIC DISCHARGE (ESD)
Action Note
3
CAUTION
CAUTION
CAUTION
xx1300002428
Action Note
7 Valid for IRB 1200 Type B
Loose the connector screws.
xx1700000004
xx1700000005
Removing the EIB unit (IRB 1200 no type specified and IRB 1200 Type A)
Action Note
1
DANGER
2
ELECTROSTATIC DISCHARGE (ESD)
Action Note
3
CAUTION
xx1300002571
xx1300002572
Action Note
6 Remove the EIB unit by removing the distance
screws.
xx1300002573
2
ELECTROSTATIC DISCHARGE (ESD)
3
CAUTION
Action Note
4 Disconnect the battery cable.
xx1700000006
xx1700000008
xx1700000009
Refitting the EIB unit (IRB 1200 no type specified and IRB 1200 Type A)
Action Note
1
ELECTROSTATIC DISCHARGE (ESD)
xx1300002573
Action Note
4 Refit the battery pack plate with the screws. Tightening torque: 1.5 Nm.
xx1300002572
xx1300002571
Action Note
3 Refit the SMB unit with the distance screws.
xx1700000009
4 Refit the battery pack plate with the screws. Tightening torque: 1.5 Nm.
xx1700000008
xx1700000006
xx1400000475
Action Note
4 Valid for IRB 1200 (no type specified) and IRB
1200 Type A
Connect the connectors to the EIB unit.
• R1.ME1-3
• R1.ME4-6
• R2.EIB
WARNING
5 Valid for IRB 1200 (no type specified) and IRB xx1300002428
1200 Type A
Connect the lugs to the EIB/SMB cover.
6 Valid for IRB 1200 Type B
Connect the connectors to the SMB unit.
• R1.ME1,2,4,5
• R1.ME3,6
• R2.SMB
WARNING
xx1700000005
xx1700000004
Action Note
8 Refit the EIB/SMB cover to the lower arm with the Screws: 3HAB3409-207 (M3x8).
attachment screws. Tightening torque: 1.5 Nm
xx1300002427
Note
9 Refit the fix sheet attachment screws in the lower Tightening torque: 1.5 Nm.
arm.
xx1300002426
Concluding procedure
Action Note
1 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry 3HAC056724-001 (not Hygienic robots) /
Plus 3HAC080702-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the cable housing
cover.
Replace if damaged.
xx1400000048
2 Check the PTFE film on the cable housing PTFE film on cable housing cover:
cover. 3HAC044660-001
Replace if damaged.
3 Apply grease to the inner surface of the
cable housing cover and the PTFE film
surface.
Action Note
4 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm.
For robots with protection type Foundry
Plus
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the
screws securing the cover.
xx1300002400
Note
Note
xx1400000423
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cable straps -
Cleaning agent - Loctite 7063
Locking liquid 3HAB7116-1 Loctite 243
Flange sealing 12340011-116 Loctite 574
Grease 3HAC042536-001 Used for lubrication of cable con-
tact areas.
Grease 3HAC029132-001 Used for lubrication of cable con-
tact areas for robots with food
grade lubrication and robots in
protection type Hygienic.
Sealant 3HAC026759-001 Sikaflex 521FC
For robots with protection type
Clean Room
For robots with food grade lubric-
ation
For robots with protection class
IP67
For robots with protection type
Foundry Plus
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
1 Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.
2 Jog all axes to zero position.
xx1300002581
Action Note
3
DANGER
4
CAUTION
2
CAUTION
Action Note
3 Remove the covers on each side of the wrist by
removing their screws.
For robots with protection class
Note IP67
For robots with protection type
For robots with protection class IP67 Foundry Plus
For robots with protection type Foundry Plus
The two front screws on the left hand side cover
(encircled in the figure) have been fitted with
locking liquid.
The tubular cover (left hand side cover) has two
extra screws and washers, as encircled in the
figure.
xx1300002349
xx1600001148
xx2100001406
Action Note
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
Action Note
3 Snap loose and disconnect the axis-5 FPC
connectors.
xx1300002390
2
CAUTION
xx1400000738
xx1500000252
2
CAUTION
xx1300002400
xx1300002413
Action Note
5 Pull out the FPC connectors from the housing and Cable layout in IRB 1200-7/0.7 :
disconnect them.
xx1300002412
xx1400001471
xx1300002398
Action Note
7 Disconnect the remaining FPC connectors.
xx1300002399
2
CAUTION
CAUTION
xx1300000456
Action Note
4 Cut the strap that holds the connectors.
xx1300002494
Tip
xx1300002495
2
CAUTION
Action Note
3 Pull out the axis-3 motor connectors from the
housing and disconnect them.
xx1300002420
2
CAUTION
xx1300002422
Action Note
4 Remove the screws that fasten the fix sheet to
the inner plastic guide.
xx1300002421
xx1300002423
CAUTION
xx1300002424
Action Note
2
ELECTROSTATIC DISCHARGE (ESD)
3
CAUTION
CAUTION
CAUTION
xx1300002428
Action Note
7 Valid for IRB 1200 Type B
Loose the connector screws.
xx1700000004
xx1700000005
2
CAUTION
Action Note
4 Remove the fix sheet attachment screws in the
lower arm.
xx1300002426
CAUTION
xx1400001130
xx1600000205
Action Note
8 Remove the swing cable housing cover by remov-
ing the screws.
xx1300002431
xx1400001528
xx1300002432
Action Note
11 Pull out the cabling and then remove the axis-2
motor bracket from the cable package by remov-
ing the screws.
CAUTION
xx1300002433
xx1300002434
xx1300002435
Action Note
14 Remove the axis-2 sealing ring by removing the
screws.
xx1400000020
Tip
xx1400000023
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the cable housing of the lower arm
by removing the screws.
xx1300002529
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the lower arm cover.
xx1300002528
4
CAUTION
WARNING
xx1300002531
Action Note
7 Fit guide pins to the upper arm. Guide pin for upper arm: 3HAC049705-001
Always use three guide pins together!
xx1400000771
xx1300002533
Action Note
1
DANGER
Action Note
2
CAUTION
xx1300002551
WARNING
xx1300002552
Action Note
5 Fit guide pins to the gearbox. Guide pin for axis-2 gear unit:
3HAC049704-001
Always use three guide pins together!
xx1300002563
Tip
xx1300002553
Action Note
1
DANGER
2
CAUTION
Action Note
3
CAUTION
WARNING
xx1400000008
xx1300002555
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check if there is a sufficient amount of Harmonic grease 4B No. 2: 3HAC037302-
grease on the gear. Apply more grease, if 001
needed. For robots with food grade lubrication
For robots with protection type Hygienic
LUBRIPLATE SYNXTREME FG-0:
3HAC043771-001
3 For robots with protection class IP67
For robots with protection type Foundry
Plus
Remove residual locking liquid and other
pollutants with cleaning agent Loctite 7063.
Apply flange sealing Loctite 574 on the
mounting surfaces of the lower arm.
xx1400000006
Action Note
4 Carefully insert the complete drive unit.
Note
xx1300002580
xx1400000795
xx1300002554
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check the o-ring. O-ring: 3HAC048939-001
Replace if damaged.
xx1300002556
Note
xx1400001403
Action Note
4 Fit guide pins to the gearbox. Guide pin for axis-2 gear unit:
3HAC049704-001
xx1300002562
CAUTION
xx1400000453
xx1300002563
Action Note
7 Refit the lower arm screws and washers, Screws: 3HAB3409-51 (M10x30).
using locking liquid Loctite 243.
Secure the screws but do not tighten yet.
xx1300002564
Note
xx1300002565
Action Note
10 For robots with protection class IP67 Gasket on swing cover: 3HAC056727-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080705-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the swing cover gasket.
Replace if damaged.
xx1400000007
xx1300002551
Action Note
12 For robots with protection type Foundry Protection plug for lifting holes:
Plus 3HAC4836-24
Check the protection plugs for lifting holes.
Replace if damaged.
xx1600001151
13 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the swing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000217
xx1600001154
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Fit guide pins to the axis-3 gear unit. Guide pin for upper arm: 3HAC049705-001
Always use three guide pins together!
xx1400000027
CAUTION
xx1400000474
Action Note
4 Refit the upper arm to the lower arm and Screws: 3HAB3409-213 (M4x25).
secure with the upper arm screws and
washers. Do not tighten yet.
xx1400000028
Note
xx1400000029
Action Note
7 For robots with protection class IP67 Gasket on lower arm cover: 3HAC056725-
For robots with protection type Foundry 001 (not Hygienic robots) / 3HAC080703-
Plus 001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the lower arm cover gasket.
Replace if damaged.
xx1400000047
xx1300002528
Note
Action Note
9 For robots with protection class IP67 Gasket on lower arm cable housing:
For robots with protection type Foundry 3HAC044895-001 (not Hygienic robots) /
Plus 3HAC080696-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the cable housing gasket.
Replace if damaged.
xx1400000414
CAUTION
Note
Action Note
11 Refit the cable housing of the lower arm. Tightening torque: 3 Nm
xx1400000785
12 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the cable housing of the lower arm. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
Note
xx1600001155
xx1400000476
xx1400000457
Action Note
4 Fetch the cable housing, the plastic plate and the
axis-2 sealing ring and run the cable package
through them.
xx1400000025
5 Fasten the plastic plate to the cable housing, if The plastic plate is included in:
removed. Cable harness material set:
Replace if damaged. 3HAC049663-001.
xx1400000023
Action Note
6 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-
For robots with protection type Foundry Plus 004
Check the sealing.
Replace if damaged.
CAUTION
xx1400000454
Action Note
7 For robots with protection class IP67 Radial sealing with dust lip:
For robots with protection type Foundry Plus 3HAB3701-41
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the radial sealing.
Replace if damaged.
Note
xx1400000753
Tip
9 Refit the axis-2 sealing ring with the screws. Tightening torque: 1.5 Nm.
xx1400000020
Action Note
10 Refit the cable housing with the screws. Screws: 3HAB3409-236 (M4x10).
Tightening torque: 3 Nm.
xx1300002435
Note
xx1400000481
Action Note
12 Reconnect the motor connectors.
• R2.ME2
• R2.MP2
xx1300002434
13 Refit the axis-2 motor bracket to the cable pack- Tightening torque: 1.5 Nm.
age with the two screws.
CAUTION
xx1400000021
xx1300002432
Action Note
15 Secure the connector R2.MP2 and its cable with
cable straps onto the motor bracket. Make sure
the connector is fixed by its tab to the bracket.
xx1400001529
xx1400000482
Action Note
18 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056726-001 (not Hygienic
robots) / 3HAC080704-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000424
Action Note
21 Refit the cable housing cover. Cable housing cover of the swing:
Replace if damaged. 3HAC059678-001
Cable housing cover of the swing,
Note Clean Room
Cable housing cover of the swing,
Remember to refit the two lower screws shown food grade lubrication
in the figure. Cable housing cover of the swing,
Hygienic
: 3HAC056214-001
Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
xx1300002431
Note
22 For robots with protection type Foundry Plus Protection plug for lifting holes:
Check the protection plugs for lifting holes. 3HAC4836-24
Replace if damaged.
xx1600001151
Action Note
23 For robots with protection type Clean Room Swing sealing plug:3HAC053687-
For robots with food grade lubrication 001
For robots with protection type Hygienic
Refit the swing sealing plug.
Follow the procedure specified in Refitting the
swing sealing plug on page 167.
xx1600000205
24 Refit the lower arm bracket to the cable package. Tightening torque: 1.5 Nm.
CAUTION
xx1300002430
Action Note
3 For robots with protection class IP67 Gasket on EIB/SMB cover:
For robots with protection type Foundry Plus 3HAC056728-001 (not Hygienic
robots) / 3HAC080706-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the EIB/SMB cover gasket.
Replace if damaged.
xx1400000475
WARNING
5 Valid for IRB 1200 (no type specified) and IRB xx1300002428
1200 Type A
Connect the lugs to the EIB/SMB cover.
6 Valid for IRB 1200 Type B
Connect the connectors to the SMB unit.
• R1.ME1,2,4,5
• R1.ME3,6
• R2.SMB
WARNING
xx1700000005
Action Note
7 Valid for IRB 1200 Type B Tightening torque: 0.3 Nm
Tighten the connector screws.
xx1700000004
8 Refit the EIB/SMB cover to the lower arm with the Screws: 3HAB3409-207 (M3x8).
attachment screws. Tightening torque: 1.5 Nm
xx1300002427
Note
Action Note
9 Refit the fix sheet attachment screws in the lower Tightening torque: 1.5 Nm.
arm.
xx1300002426
xx1400000483
Action Note
3 Guide the cable package into the upper arm,
through the housing.
Note
4 Refit the bracket to the sheet with two screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300002424
5 Refit the fix sheet to the motor. Tightening torque: 1.5 Nm.
xx1300002423
Action Note
6 Refit the fix sheet to the inner plastic guide. Tightening torque: 1.5 Nm.
xx1300002421
7 Fit the air hose holder to the bracket. Air hose holders are included in
Replace the holder, if damaged. Cable harness material set
(3HAC049663-001).
Tightening torque: 4 Nm.
Tip
xx1300002422
xx1400001133
xx1300002420
Action Note
9 Apply grease to the cable package, cover all
moving area of the package.
xx1400000754
xx1300002371
Action Note
3 Secure the connectors to the motor with a cable
strap.
xx1300002494
Tip
xx1300002399
Action Note
3 Reconnect the FPC connectors and push them Cable layout in IRB 1200-7/0.7 :
into place inside the housing.
Tip
xx1300002412
xx1400001471
Action Note
5 For robots with protection class IP67
For robots with protection type Foundry Plus
Apply flange sealing Sikaflex 521FC on the
mounting surfaces of the small cover on the
housing.
6 Refit the small cover to the housing.
Replace if damaged.
xx1300002398
xx1600000214
Action Note
8 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
9 Check the PTFE film on the cable housing. PTFE film on lower arm cable
Replace if damaged. housing: 3HAC044710-001
xx1400000740
Action Note
10 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056724-001 (not Hygienic
robots) / 3HAC080702-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication PTFE film on cable housing cover:
For robots with protection type Hygienic 3HAC044660-001
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000048
Action Note
13 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the screws
securing the cover.
xx1300002400
Note
Connecting the air hoses and CP/CS cabling on robots not in protection type Hygienic
Use this procedure if the robot is not in protection type Hygienic.
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 Reconnect the air hoses. Air connector set with Ethernet
Replace the air hose connector set if damaged. hole in flange: 3HAC049664-001
Air connector set without Ethernet
hole in flange: 3HAC049665-001
xx1400000738
Action Note
3 If equipped, reconnect the CP/CS connector.
For robots with protection class IP67
For robots with protection type Foundry Plus
1 Check the gasket.
2 Replace if damaged.
For robots with protection type Clean Room
For robots with food grade lubrication
1 Remove residual locking liquid and other xx1500000252
pollutants with cleaning agent Loctite 7063.
On robots with protection class
2 Apply flange sealing Loctite 574 on the IP67
mounting surfaces of the CP/CS connector
and wipe clean if there is any overflowing On robots with protection type
Loctite 574. Foundry Plus
Gasket: 3HAC058567-001
xx1500000251
4 For robots with protection type Foundry Plus Protection bracket for CP/CS con-
If required, fit the protection bracket for CP/CS nectors: 3HAC058350-001
connectors.
xx1600001152
Connecting the air hoses and CP/CS cabling on robots in protection type Hygienic
Use this procedure if the robot is with protection type Hygienic.
Action Note
1 Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
Action Note
2 If the Hygienic robot not equipped with air hoses Plate without connector set:
and CP/CS cabling: 3HAC078810-001
Check the plate without connector set and the at- Gasket: 3HAC078804-001
tached gasket.
Replace if damaged.
xx2100001433
xx1400000738
xx1500000252
5 Check the connectors on the plate with connector Plate with connector set:
set and the attached gasket. 3HAC079691-001
Replace if damaged. Gasket: 3HAC078804-001
xx2100001434
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
Concluding procedure
Action Note
1 For robots with protection class IP67 Housing cover gasket (IRB 1200-7/0.7 ):
For robots with protection type Foundry 3HAC056698-001 (not Hygienic robots) /
Plus 3HAC080700-001 (Hygienic robots)
For robots with protection type Clean Housing cover gasket (IRB 1200-5/0.9 ):
Room 3HAC056697-001 (not Hygienic robots) /
3HAC080699-001 (Hygienic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000477
2 Refit the upper arm housing cover with the Screws: 3HAB3409-207 (M3x8).
screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300000456
Note
Action Note
3 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the upper arm housing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000215
Note
xx1300000455
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Action Note
1
DANGER
2
CAUTION
xx1300000456
Action Note
8 Clean the joints that have been opened. See Cut
the paint or surface on the robot before replacing
parts on page 158
9 For robots with protection class IP67 Housing cover gasket (IRB 1200-
For robots with protection type Foundry Plus 7/0.7 ): 3HAC056698-001 (not Hy-
gienic robots) / 3HAC080700-001
For robots with protection type Clean Room (Hygienic robots)
For robots with food grade lubrication Housing cover gasket (IRB 1200-
For robots with protection type Hygienic 5/0.9 ): 3HAC056697-001 (not Hy-
Check the gasket. gienic robots) / 3HAC080699-001
Replace if damaged. (Hygienic robots)
xx1400000477
10 Refit the cover on the upper arm housing. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
Note
Note
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
1 Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.
2 Jog all axes to zero position.
xx1300002581
Action Note
3
DANGER
4
CAUTION
2
CAUTION
Action Note
3 Remove the covers on each side of the wrist by
removing their screws.
For robots with protection class
Note IP67
For robots with protection type
For robots with protection class IP67 Foundry Plus
For robots with protection type Foundry Plus
The two front screws on the left hand side cover
(encircled in the figure) have been fitted with
locking liquid.
The tubular cover (left hand side cover) has two
extra screws and washers, as encircled in the
figure.
xx1300002349
xx1600001148
xx2100001406
Action Note
2
CAUTION
xx1300002390
xx1300002391
Note
xx1300002392
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Check the sealing. M2 variseal sealing: 3HAC044641-009
Replace if damaged.
CAUTION
xx1300002396
xx1300002608
xx1400000485
Action Note
8 Screw the screws, little by little, to press
the sealing into place.
xx1400000486
xx1300002610
Action Note
3 Refit the tubular cable housing with the screws. Tightening torque: 1.5 Nm.
Tubular cable housing:
3HAC059695-001
Tubular cable housing, Clean
Room
Tubular cable housing, food grade
lubrication
: 3HAC056143-001
Tubular cable housing, Hygienic:
3HAC079692-001
xx1300002392
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the connector plate and secure with Tightening torque: 0.3 Nm.
the M3 screws.
xx1400001401
Action Note
3 Secure the three M2.5 screws. Tightening torque: 0.3 Nm.
xx1400001402
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
2
CAUTION
Action Note
3 Remove the covers on each side of the wrist by
removing their screws.
For robots with protection class
Note IP67
For robots with protection type
For robots with protection class IP67 Foundry Plus
For robots with protection type Foundry Plus
The two front screws on the left hand side cover
(encircled in the figure) have been fitted with
locking liquid.
The tubular cover (left hand side cover) has two
extra screws and washers, as encircled in the
figure.
xx1300002349
xx1600001148
xx2100001406
Action Note
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
xx1300002350
Action Note
4 Remove the timing belt.
xx1300002351
xx1300002390
xx1300002352
Action Note
2
CAUTION
xx1300002353
xx1300002355
xx1300002356
Action Note
6 Guide the hoses through the plate hole and re-
move the plate.
xx1300002357
xx1300002358
CAUTION xx1300002359
xx1300002611
2
CAUTION
Note
xx1300002469
5 Fit guide pins to the gearbox. Guide pin for tilt unit (axis 5):
3HAC049706-001
Always use three guide pins togeth-
er!
xx1400000775
Action Note
6 Remove the tilt unit.
xx1300002470
xx2100001448
xx2100001449
Action Note
4 Insert two M4 screws to the pressed out holes
and press out the stainless shaft.
xx2100001450
xx2100001451
5 Place the flange tightening tool together with a Flange tightening tool:
3/8" (10 mm) socket spanner on the seal ring unit 3HAC079686-001
and loosen the unit.
xx2100001452
xx2100001453
Action Note
8 Apply a little grease to the screw thread. Grease: Molykote P1900
xx2100001454
xx2100001453
xx2100001455
10 Place the flange tightening tool together with a Flange tightening tool:
3/8" (10 mm) socket spanner on the seal ring unit 3HAC079686-001
and tighten the unit. Tightening torque: 6 Nm
xx2100001456
Action Note
11 Fit two guide pins to the tool flange. Guide pin for stainless shaft on tool
flange: 3HAC079684-001
xx2100001457
xx2100001458
xx2100001459
xx2100001460
Action Note
2 For robots with protection type Foundry Plus Protection cover for axis-6 turning
Check the protection cover for turning disk and disk: 3HAC044666-001
T40 variseal sealing. T40 variseal sealing: 3HAC044641-
Replace if damaged. 012
xx1600001126
CAUTION
xx1300002493
4 Remove residual locking liquid and other pollut- For robots not in protection type
ants with cleaning agent Loctite 7063. Hygienic
Apply flange sealing on the mounting surfaces of Flange sealant, SikaFlex 521FC
the drive unit. For robots with protection type
Hygienic
Note Flange sealant, Trans Clear
xx1400001404
Action Note
5 Fit guide pins to the axis-5 gearbox. Guide pin for tilt unit (axis 5):
3HAC049706-001
xx1300002568
xx1600000219
xx1600000220
Action Note
7 Refit the drive unit and secure with the screws Attachment screws: 3HAB3409-236
and washers. (M4x10).
Secure the screws but do not tighten yet.
Note
xx1300002569
Note
xx1300002570
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Check the sealing. M2 variseal sealing: 3HAC044641-009
Replace if damaged.
CAUTION
xx1300002396
xx1300002608
xx1400000485
Action Note
8 Screw the screws, little by little, to press
the sealing into place.
xx1400000486
xx1300002610
Action Note
3 Refit the tubular cable housing with the screws. Tightening torque: 1.5 Nm.
Tubular cable housing:
3HAC059695-001
Tubular cable housing, Clean
Room
Tubular cable housing, food grade
lubrication
: 3HAC056143-001
Tubular cable housing, Hygienic:
3HAC079692-001
xx1300002392
CAUTION xx1300002359
xx1300002611
Action Note
3 Refit the washer while at the same time putting Washer: 3HAC044869-001
the cables through its center.
Replace washer, if damaged.
xx1400000001
4 Refit the screw M6x35 (1 pc). Do not tighten yet. Screw: 3HAB3409-238 (M6x35 (1
pc)).
xx1400000002
Note
5 Refit the rest of the screws (M5x35 (7 pcs)). Screw: 3HAB3409-237 (M5x35 (7
pcs)).
xx1400000003
Note
Action Note
7 Put the cables through the plate hole and refit the Tightening torque: 0.3 Nm.
plate.
xx1300002356
CAUTION
xx1300002355
xx1300002353
Action Note
3 Place the motor at its mounting position and Screws: 3HAB3409-212 (M4x16).
fasten the attachment screws and washers just
enough to still be able to move the motor.
xx1300002463
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the timing belt on the pulley.
xx1300002351
Action Note
4 Secure the motor with its attachment
screws.
xx1300002350
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the connector plate and secure with Tightening torque: 0.3 Nm.
the M3 screws.
xx1400001401
xx1400001402
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
Concluding procedures
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean, seal and paint the joints that have
been opened. See Cut the paint or surface
on the robot before replacing parts on
page 158.
Note
xx1400000336
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
1 Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.
2 Jog all axes to zero position.
xx1300002581
3
DANGER
4
CAUTION
Action Note
5 Remove the wrist cover.
xx1300002389
2
CAUTION
Tip
Action Note
1
DANGER
Action Note
2
CAUTION
xx1300002390
2
CAUTION
xx1400000738
Action Note
4 If equipped, disconnect the CP/CS connector.
xx1500000252
2
CAUTION
xx1300002400
Action Note
4 Remove the plate.
xx1300002413
5 Pull out the FPC connectors from the housing and Cable layout in IRB 1200-7/0.7 :
disconnect them.
xx1300002412
xx1400001471
Action Note
6 Remove the small cover of the housing.
xx1300002398
xx1300002399
2
CAUTION
Action Note
3 Remove the cover from the upper arm housing.
CAUTION
xx1300000456
xx1300002494
Tip
xx1300002495
Action Note
2
CAUTION
xx1300002420
2
CAUTION
Action Note
3 Remove the screw that fastens the air hose hold-
er.
xx1300002422
xx1300002421
xx1300002423
CAUTION
xx1300002424
Action Note
7 Valid for IRB 1200-5/0.9
Cut the cable straps at the bottom of the housing.
Action Note
1
DANGER
2
CAUTION
xx1300002529
2
CAUTION
xx1400000473
Action Note
4 Remove the axis-3 radial sealing.
xx1400000334
2
CAUTION
Action Note
3 Remove the screws.
xx1400000332
xx1400000333
Action Note
2 For robots with protection class IP67
For robots with protection type Foundry
Plus
Remove residual locking liquid and other
pollutants with cleaning agent Loctite 7063.
Apply flange sealing Loctite 574 on the
mounting surfaces of the sealing ring.
3 Refit the axis-3 sealing ring by securing the Tightening torque: 1.5 Nm
screws.
Note
xx1400000333
xx1400000332
Action Note
3 Fit the axis-3 radial sealing to the cable housing. Radial sealing: 3HAC024865-001
xx1400000334
4 Put the assembly tool on both sides of the cable Axis-3 sealing assembly tool set:
housing, circular part against the sealing, and 3HAC049697-001
then slowly press the sealing into the housing by
screwing the six screws (M6X50) into the plate
little by little.
Fit the circular part of the radial sealing fitting tool
against the radial sealing.
5 Fit the tool plate to the other side of the cable
housing with the six screws M6X50.
6 Screw the screws, little by little, to press the
sealing into place.
xx1400000335
Action Note
8 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-
For robots with protection type Foundry Plus 006
Fit a new M2 variseal sealing.
xx1400000473
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection class IP67 Gasket on lower arm cable housing:
For robots with protection type Foundry 3HAC044895-001 (not Hygienic robots) /
Plus 3HAC080696-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the cable housing gasket.
Replace if damaged.
xx1400000414
Action Note
3 For robots with protection class IP67 Radial sealing: 3HAC024865-001
For robots with protection type Foundry M2 variseal sealing: 3HAC044641-006
Plus
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the radial sealing and the M2
variseal sealing.
Replace if damaged.
CAUTION
Note
4 Refit the cable housing of the lower arm. Tightening torque: 4 Nm.
xx1300002529
Action Note
5 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the cable housing of the lower arm. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
Note
xx1400000483
Action Note
3 Guide the cable package into the upper arm,
through the housing.
Note
4 Refit the bracket to the sheet with two screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300002424
5 Refit the fix sheet to the motor. Tightening torque: 1.5 Nm.
xx1300002423
Action Note
6 Refit the fix sheet to the inner plastic guide. Tightening torque: 1.5 Nm.
xx1300002421
7 Fit the air hose holder to the bracket. Air hose holders are included in
Replace the holder, if damaged. Cable harness material set
(3HAC049663-001).
Tightening torque: 4 Nm.
Tip
xx1300002422
xx1400001133
xx1300002420
Action Note
9 Apply grease to the cable package, cover all
moving area of the package.
xx1400000754
xx1300002371
Action Note
3 Secure the connectors to the motor with a cable
strap.
xx1300002494
Tip
xx1300002399
Action Note
3 Reconnect the FPC connectors and push them Cable layout in IRB 1200-7/0.7 :
into place inside the housing.
Tip
xx1300002412
xx1400001471
Action Note
5 For robots with protection class IP67
For robots with protection type Foundry Plus
Apply flange sealing Sikaflex 521FC on the
mounting surfaces of the small cover on the
housing.
6 Refit the small cover to the housing.
Replace if damaged.
xx1300002398
xx1600000214
Action Note
8 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
9 Check the PTFE film on the cable housing. PTFE film on lower arm cable
Replace if damaged. housing: 3HAC044710-001
xx1400000740
Action Note
10 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056724-001 (not Hygienic
robots) / 3HAC080702-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication PTFE film on cable housing cover:
For robots with protection type Hygienic 3HAC044660-001
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000048
Action Note
13 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the screws
securing the cover.
xx1300002400
Note
Connecting the air hoses and CP/CS cabling on robots not in protection type Hygienic
Use this procedure if the robot is not in protection type Hygienic.
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 Reconnect the air hoses. Air connector set with Ethernet
Replace the air hose connector set if damaged. hole in flange: 3HAC049664-001
Air connector set without Ethernet
hole in flange: 3HAC049665-001
xx1400000738
Action Note
3 If equipped, reconnect the CP/CS connector.
For robots with protection class IP67
For robots with protection type Foundry Plus
1 Check the gasket.
2 Replace if damaged.
For robots with protection type Clean Room
For robots with food grade lubrication
1 Remove residual locking liquid and other xx1500000252
pollutants with cleaning agent Loctite 7063.
On robots with protection class
2 Apply flange sealing Loctite 574 on the IP67
mounting surfaces of the CP/CS connector
and wipe clean if there is any overflowing On robots with protection type
Loctite 574. Foundry Plus
Gasket: 3HAC058567-001
xx1500000251
4 For robots with protection type Foundry Plus Protection bracket for CP/CS con-
If required, fit the protection bracket for CP/CS nectors: 3HAC058350-001
connectors.
xx1600001152
Connecting the air hoses and CP/CS cabling on robots in protection type Hygienic
Use this procedure if the robot is with protection type Hygienic.
Action Note
1 Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
Action Note
2 If the Hygienic robot not equipped with air hoses Plate without connector set:
and CP/CS cabling: 3HAC078810-001
Check the plate without connector set and the at- Gasket: 3HAC078804-001
tached gasket.
Replace if damaged.
xx2100001433
xx1400000738
xx1500000252
5 Check the connectors on the plate with connector Plate with connector set:
set and the attached gasket. 3HAC079691-001
Replace if damaged. Gasket: 3HAC078804-001
xx2100001434
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
xx1300002389
Note
Concluding procedure
Action Note
1 For robots with protection class IP67 Housing cover gasket (IRB 1200-7/0.7 ):
For robots with protection type Foundry 3HAC056698-001 (not Hygienic robots) /
Plus 3HAC080700-001 (Hygienic robots)
For robots with protection type Clean Housing cover gasket (IRB 1200-5/0.9 ):
Room 3HAC056697-001 (not Hygienic robots) /
3HAC080699-001 (Hygienic robots)
For robots with food grade lubrication
Check the gasket.
Replace if damaged.
xx1400000477
2 Refit the upper arm housing cover with the Screws: 3HAB3409-207 (M3x8).
screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300000456
Note
Action Note
3 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the upper arm housing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000215
Note
xx1400000389
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Action Note
1 Jog the robot to a position where the
mechanical stop is most easily accessed.
2
DANGER
3
CAUTION
Action Note
1
DANGER
Action Note
2
CAUTION
xx1400000390
Note
Note
7
DANGER
xx1400000386
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Action Note
1 Jog the robot to a position where the
mechanical stops are most easily ac-
cessed.
2
DANGER
3
CAUTION
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the mechanical stop to be re-
placed by removing the screws.
4 Discard the old screws.
5 Refit and secure the new stop with the en-
closed screws.
xx1400000387
Note
Note
7
DANGER
WARNING
xx1300002416
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cleaning agent - Loctite 7063
Flange sealing 12340011-116 Loctite 574
Used with protection class IP67
Used with protection type
Foundry Plus
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
1 Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.
Action Note
2 Jog all axes to zero position.
xx1300002581
3
DANGER
4
CAUTION
Action Note
2
CAUTION
xx1300002349
xx1600001148
xx2100001406
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
Action Note
3 Loosen the screws so that the motor can
be moved sideways.
xx1300002350
xx1300002351
xx1300002390
xx1300002352
2
CAUTION
xx1300002353
xx1300002355
xx1300002356
Action Note
6 Guide the hoses through the plate hole and re-
move the plate.
xx1300002357
xx1300002358
CAUTION xx1300002359
xx1300002611
2
CAUTION
xx1300002400
xx1300002413
Action Note
5 Pull out the FPC connectors from the housing and Cable layout in IRB 1200-7/0.7 :
disconnect them.
xx1300002412
xx1400001471
xx1300002398
Action Note
7 Disconnect the remaining FPC connectors.
xx1300002399
2
CAUTION
xx1300002373
xx1600000262
Action Note
5 Remove the extender unit screws.
xx1300002372
xx1300002374
2
CAUTION
xx1300002415
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-007
For robots with protection type Foundry
Plus
Check the sealing.
Replace if damaged.
CAUTION
xx1300002418
3 For robots with protection class IP67 Radial sealing with dust lip: 3HAB3701-48
For robots with protection type Foundry
Plus
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the radial sealing.
Replace if damaged, as described below.
In order to replace the radial sealing, both
the axis-4 mechanical stop and the axis-4
FPC unit must be removed from the hous-
ing extender unit, if not already removed.
xx1400000438
Action Note
4 Apply a little grease to the sealing when
replacing the radial sealing and wipe clean
after the replacement.
5 Fit the radial sealing into the housing ex-
tender unit.
6 Fit the circular part of the radial sealing Axis-4 sealing assembly tool set:
assembly tool against the radial sealing. 3HAC049699-001
7 Fit the tool plate to the other side of the
housing extender unit with the six screws
M6X50.
xx1400000436
xx1400000437
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Fit the mechanical stop screw to the axis- Screws: 3HAB3409-231 (M4x8).
4 shaft. Tightening torque: 4 Nm.
xx1400000393
xx1300002415
Note
xx1300002613
xx1600000216
CAUTION
Note
Action Note
5 Secure with screws and washers, using locking Screws: M4x30.
liquid Loctite 243. Tightening torque: 2.7 Nm.
xx1300002372
6 For robots with protection type Foundry Plus Screw sealing plug: 3HAC053685-
For robots with protection type Clean Room 001
For robots with food grade lubrication
For robots with protection type Hygienic
Press in screw sealing plugs to cover the screws.
xx1600000263
7 Fit and secure the axis-4 FPC unit screws. Tightening torque: 0.3 Nm.
xx1300002373
Action Note
2 Reconnect the FPC connectors.
Tip
xx1300002399
3 Reconnect the FPC connectors and push them Cable layout in IRB 1200-7/0.7 :
into place inside the housing.
Tip
xx1300002412
xx1400001471
Action Note
5 For robots with protection class IP67
For robots with protection type Foundry Plus
Apply flange sealing Sikaflex 521FC on the
mounting surfaces of the small cover on the
housing.
6 Refit the small cover to the housing.
Replace if damaged.
xx1300002398
xx1600000214
Action Note
8 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
9 Check the PTFE film on the cable housing. PTFE film on lower arm cable
Replace if damaged. housing: 3HAC044710-001
xx1400000740
Action Note
10 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056724-001 (not Hygienic
robots) / 3HAC080702-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication PTFE film on cable housing cover:
For robots with protection type Hygienic 3HAC044660-001
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000048
Action Note
13 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the screws
securing the cover.
xx1300002400
Note
Action Note
2 Put the connectors and air hoses into the wrist
carefully while at the same time refitting the wrist
to the housing extender unit.
Be careful not to damage the FPC cabling and the
connectors.
CAUTION xx1300002359
xx1300002611
3 Refit the washer while at the same time putting Washer: 3HAC044869-001
the cables through its center.
Replace washer, if damaged.
xx1400000001
Action Note
4 Refit the screw M6x35 (1 pc). Do not tighten yet. Screw: 3HAB3409-238 (M6x35 (1
pc)).
xx1400000002
Note
5 Refit the rest of the screws (M5x35 (7 pcs)). Screw: 3HAB3409-237 (M5x35 (7
pcs)).
xx1400000003
Note
xx1300002356
Action Note
8 Reconnect the air hoses.
CAUTION
xx1300002355
xx1300002353
xx1300002463
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the timing belt on the pulley.
xx1300002351
xx1300002350
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Refit the connector plate and secure with Tightening torque: 0.3 Nm.
the M3 screws.
xx1400001401
xx1400001402
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
Action Note
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
Concluding procedure
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean, seal and paint the joints that have
been opened. See Cut the paint or surface
on the robot before replacing parts on
page 158.
Note
4.5.1 Replacing the base spare parts (base, axis-1 radial sealing, protection sleeve)
xx1400000395
xx1400000269
xx1400000396
xx1400000471 xx1400000471
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Equipment Art. no. Note
Cable straps -
Grease 3HAC042536-001 Used for lubrication of cable con-
tact areas.
Locking liquid 3HAB7116-1 Loctite 243
Grease 3HAC029132-001 Used for lubrication of cable con-
tact areas for robots with food
grade lubrication and robots in
protection type Hygienic.
Grease 3HAC058065-001 Used for lubrication of radial
sealing surface between base
and swing.
For robots with protection class
IP67
For robots with protection type
Foundry Plus
Sealant 12340011-116 Loctite 574
For robots with protection type
Clean Room
For robots with food grade lubric-
ation
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
2 Jog all axes to zero position.
xx1300002581
3
DANGER
4
CAUTION
xx1300002389
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
Action Note
3 Snap loose and disconnect the axis-5 FPC
connectors.
xx1300002390
2
CAUTION
xx1400000738
xx1500000252
2
CAUTION
xx1300002400
xx1300002413
Action Note
5 Pull out the FPC connectors from the housing and Cable layout in IRB 1200-7/0.7 :
disconnect them.
xx1300002412
xx1400001471
xx1300002398
Action Note
7 Disconnect the remaining FPC connectors.
xx1300002399
2
CAUTION
CAUTION
xx1300000456
Action Note
4 Cut the strap that holds the connectors.
xx1300002494
Tip
xx1300002495
2
CAUTION
Action Note
3 Pull out the axis-3 motor connectors from the
housing and disconnect them.
xx1300002420
2
CAUTION
xx1300002422
Action Note
4 Remove the screws that fasten the fix sheet to
the inner plastic guide.
xx1300002421
xx1300002423
CAUTION
xx1300002424
Action Note
2
ELECTROSTATIC DISCHARGE (ESD)
3
CAUTION
CAUTION
CAUTION
xx1300002428
Action Note
7 Valid for IRB 1200 Type B
Loose the connector screws.
xx1700000004
xx1700000005
2
CAUTION
Action Note
4 Remove the fix sheet attachment screws in the
lower arm.
xx1300002426
CAUTION
xx1400001130
xx1600000205
Action Note
8 Remove the swing cable housing cover by remov-
ing the screws.
xx1300002431
xx1400001528
xx1300002432
Action Note
11 Pull out the cabling and then remove the axis-2
motor bracket from the cable package by remov-
ing the screws.
CAUTION
xx1300002433
xx1300002434
xx1300002435
Action Note
14 Remove the axis-2 sealing ring by removing the
screws.
xx1400000020
Tip
xx1400000023
Action Note
1
DANGER
2
CAUTION
Action Note
3
CAUTION
CAUTION
xx1400000679
5
WARNING
6
CAUTION
Action Note
7 Loosen the robot from the foundation by
removing the foundation attachment
screws and put the robot on its side.
xx1400000680
2
CAUTION
Tip
xx1300000467
Action Note
4 Remove the screws and washers.
xx1300000471
Tip
xx1300000472
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the axis-1 sealing ring from the swing
and carefully run the cable package out from the
swing.
xx1300002438
xx1300002446
Action Note
1
DANGER
Action Note
3 Remove the M2 variseal sealing.
The M2 variseal sealing is only installed on
base version 3HAC049628-001. See Spare
part versions for the base on IP40/IP67 ro-
bots on page 874.
xx1400000780
xx1400000270
Action Note
1 Fit the new sealing in its groove in the Radial sealing with dust lip: 3HAB3701-47
base.
xx1400000270
Action Note
2 Put the assembly tool against the axis-1 Axis-1 sealing assembly tool set:
gear and slowly press the sealing into the 3HAC049692-001
base by screwing the five screws (M10X35)
into the axis-1 gear screws little by little.
xx1400000271
CAUTION
xx1400000780
First remove the cabling according to Removing the cabling on page 497, then use
this procedure to replace the M2 variseal sealing.
Note
The sealing is only used for robots with protection class IP67. Do not fit M2
variseal sealing on robots in other protection class or protection types.
Action Note
1
DANGER
CAUTION
xx1400000472
Action Note
1
DANGER
Action Note
2
CAUTION
xx1400000776
xx1400000777
Action Note
8 Apply grease on the inner surface of the protec-
tion sleeve, also on the bottom surface.
xx1400000778
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the bottom cover. Rear connector interface:
xx1300000469
xx1400000403
Action Note
4 Remove the axis-1 motor bracket. Rear connector interface:
xx1300000470
xx1400000404
xx1300002496
2
CAUTION
xx1300002448
xx1300002456
2
CAUTION
xx1400000405
xx1400000406
Action Note
7 Remove the bracket inside the base by removing
the screws.
xx1400000407
xx1400000411
Action Note
1
DANGER
2
CAUTION
Action Note
4 Remove the M2 variseal sealing.
The M2 variseal sealing is only installed on
base version 3HAC049628-001. See Spare
part versions for the base on IP40/IP67 ro-
bots on page 874.
xx1400000780
xx1400000270
Action Note
1
DANGER
2
CAUTION
Action Note
3 Move the protection sleeve from the old base to Tightening torque: 0.3 Nm.
the new.
xx1400000776
4 Move the axis-1 mechanical stop set from the old Tightening torque: 12 Nm.
base to the new.
Replace if damaged.
xx1400000392
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection type Clean
Room
Apply a little grease to the sealing when
replacing the radial sealing and wipe clean
after the replacement.
Action Note
3 Fit the new sealing in its groove in the Radial sealing with dust lip: 3HAB3701-47
base.
xx1400000270
4 Put the assembly tool against the axis-1 Axis-1 sealing assembly tool set:
gear and slowly press the sealing into the 3HAC049692-001
base by screwing the five screws (M10X35)
into the axis-1 gear screws little by little.
xx1400000271
Action Note
6 Fit a new M2 variseal sealing in its groove
in the base.
The M2 variseal sealing is only installed on
base version 3HAC049628-001. See Spare
part versions for the base on IP40/IP67 ro-
bots on page 874.
CAUTION
xx1400000780
xx1400000741
Action Note
3 Insert the cable package in and up through the
base, through the rear.
4 Reconnect the earth cable.
5 Refit the base cover with the attachment screws. Screws: 3HAB3409-212 (M4x16).
Tightening torque: 4 Nm.
xx1300002448
Note
xx1400000480
Action Note
3 Refit the bracket inside the base with the screws. Tightening torque: 1.5 Nm.
xx1400000407
4 Refit the cable bracket with the screws. Tightening torque: 1.5 Nm.
xx1400000406
5 For robots with protection class IP67 Gasket for rear base cover:
For robots with protection type Foundry Plus 3HAC058566-001 (not Hygienic
robots) / 3HAC080710-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the base cover.
Replace if damaged.
xx1400000413
Action Note
8 Refit the base cover. Screws: 3HAB3409-212 (M4x16).
Tightening torque: 4 Nm.
xx1400000405
Note
xx1400000480
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 Check the axis-1 sealing ring. Axis-1 sealing ring: 3HAC044676-
Replace if damaged. 001 / 3HAC068107-001 i
Action Note
3 For robots with protection class IP67 Sealant: Sikaflex 521FC.
On axis-1 sealing ring version 3HAC056658-001:
Add sealant to the axis-1 sealing ring.
(See Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.)
xx1600001125
4 For robots with protection class IP67 On axis-1 sealing ring version
On axis-1 sealing ring version 3HAC044676-001, 3HAC044676-001:
3HAC058568-001 or 3HAC068107-001: Axis-1 sealing ring gasket:
For robots with protection type Foundry Plus 3HAC045685-001
On axis-1 sealing ring version 3HAC058568-001
or 3HAC068107-001:
Check the gasket on the axis-1 sealing ring.
(See Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.)
Replace if damaged.
xx1400000458
xx1600001149
xx1900001735
Action Note
5 For robots with protection class IP67 V-ring: 3HAB3732-34
On axis-1 sealing ring version 3HAC056658-001, On axis-1 sealing ring version
3HAC058568-001 or 3HAC068107-001: 3HAC056658-001:
For robots with protection type Foundry Plus
On axis-1 sealing ring version 3HAC058568-001
or 3HAC068107-001:
Check the V-ring on the axis-1 sealing ring.
(See Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.)
Replace if damaged. xx1600001124
xx1600001150
xx1900001736
6 Check the cable protection on the axis-1 sealing Cable protection: 3HAC044691-001
ring. Torx countersunk head screw
Replace if damaged. M3x5: 3HAC14286-4
If replacing the cable protection, use locking liquid Tightening torque: 0.3 Nm
Loctite 243 on the screws.
xx1400000456
7 Refit the cable bracket to the cabling, if removed. Tightening torque: 1 Nm.
Use Loctite 243 on the screw threads.
xx1300002446
Action Note
8 Refit the axis-1 sealing ring to the swing and Tightening torque: 1.5 Nm.
carefully run the cabling into the swing.
xx1300002438
i For information on which sealing ring to be ordered, see Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check the axis-1 radial sealing in the base. Radial sealing with dust lip: 3HAB3701-47
Replace if damaged. M2 variseal sealing: 3HAC044641-002
Note
CAUTION
Action Note
3 For robots with protection class IP67 Grease: 3HAC058065-001.
For robots with protection type Foundry
Plus
Apply grease to the radial sealing surface.
xx1600000170
4 Fit the guide pins to the drive unit. Guide pin for axis-1 gear unit:
3HAC049703-001
xx1300002566
CAUTION
Action Note
6 Secure with attachment screws and wash- Screws: 3HAB3409-52 (M10x35).
ers, but do not tighten yet.
xx1300002567
Note
xx1300000523
Action Note
9 For robots with protection class IP67 Gasket on top swing cover
For robots with protection type Foundry 3HAC056696-001 (not Hygienic robots) /
Plus 3HAC080698-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000425
10 Refit the swing top cover with the screws. Cover on top of swing: 3HAC059679-001
Replace if damaged. Cover on top of swing, Clean Room
Cover on top of swing, food grade lubrica-
tion
Cover on top of swing, Hygienic
: 3HAC056133-001
Screws: 3HAB3409-209 (M3x20).
Tightening torque: 1.5 Nm.
xx1300000467
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Reconnect the connectors and secure the
connectors to the bracket with cable straps.
xx1300002496
Action Note
3 Refit the axis-1 motor bracket. Tightening torque: 1.5 Nm.
Rear connector interface:
xx1300000470
xx1400000404
xx1400000412
Action Note
5 Refit the bottom cover. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
Rear connector interface:
xx1300000469
xx1400000403
Note
Action Note
2
CAUTION
xx1500000241
4 Raise the robot to standing and secure Attachment screws: M12x35 (robot installation
to the foundation with the attachment directly on foundation), quality: 8.8.
screws and washers. Washers: 13 x 20 x 2, steel hardness class
300HV.
Pin: 2 pcs, D6x20, ISO 2338 - 6m6x20 - A1.
Tightening Torque: 55 Nm ± 5 Nm.
Action Note
2 Check the axis-2 sealing ring. Axis-2 sealing ring: 3HAC044677-
For robots with protection class IP67 001
For robots with protection type Foundry Plus Gasket of axis-2 sealing ring:
3HAC045688-001 (not Hygienic
For robots with protection type Clean Room robots) / 3HAC080697-001 (Hygien-
For robots with food grade lubrication ic robots)
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000476
xx1400000457
Action Note
4 Fetch the cable housing, the plastic plate and the
axis-2 sealing ring and run the cable package
through them.
xx1400000025
5 Fasten the plastic plate to the cable housing, if The plastic plate is included in:
removed. Cable harness material set:
Replace if damaged. 3HAC049663-001.
xx1400000023
Action Note
6 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-
For robots with protection type Foundry Plus 004
Check the sealing.
Replace if damaged.
CAUTION
xx1400000454
Action Note
7 For robots with protection class IP67 Radial sealing with dust lip:
For robots with protection type Foundry Plus 3HAB3701-41
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the radial sealing.
Replace if damaged.
Note
xx1400000753
Tip
9 Refit the axis-2 sealing ring with the screws. Tightening torque: 1.5 Nm.
xx1400000020
Action Note
10 Refit the cable housing with the screws. Screws: 3HAB3409-236 (M4x10).
Tightening torque: 3 Nm.
xx1300002435
Note
xx1400000481
Action Note
12 Reconnect the motor connectors.
• R2.ME2
• R2.MP2
xx1300002434
13 Refit the axis-2 motor bracket to the cable pack- Tightening torque: 1.5 Nm.
age with the two screws.
CAUTION
xx1400000021
xx1300002432
Action Note
15 Secure the connector R2.MP2 and its cable with
cable straps onto the motor bracket. Make sure
the connector is fixed by its tab to the bracket.
xx1400001529
xx1400000482
Action Note
18 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056726-001 (not Hygienic
robots) / 3HAC080704-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000424
Action Note
21 Refit the cable housing cover. Cable housing cover of the swing:
Replace if damaged. 3HAC059678-001
Cable housing cover of the swing,
Note Clean Room
Cable housing cover of the swing,
Remember to refit the two lower screws shown food grade lubrication
in the figure. Cable housing cover of the swing,
Hygienic
: 3HAC056214-001
Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
xx1300002431
Note
22 For robots with protection type Foundry Plus Protection plug for lifting holes:
Check the protection plugs for lifting holes. 3HAC4836-24
Replace if damaged.
xx1600001151
Action Note
23 For robots with protection type Clean Room Swing sealing plug:3HAC053687-
For robots with food grade lubrication 001
For robots with protection type Hygienic
Refit the swing sealing plug.
Follow the procedure specified in Refitting the
swing sealing plug on page 167.
xx1600000205
24 Refit the lower arm bracket to the cable package. Tightening torque: 1.5 Nm.
CAUTION
xx1300002430
Action Note
3 For robots with protection class IP67 Gasket on EIB/SMB cover:
For robots with protection type Foundry Plus 3HAC056728-001 (not Hygienic
robots) / 3HAC080706-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the EIB/SMB cover gasket.
Replace if damaged.
xx1400000475
WARNING
5 Valid for IRB 1200 (no type specified) and IRB xx1300002428
1200 Type A
Connect the lugs to the EIB/SMB cover.
6 Valid for IRB 1200 Type B
Connect the connectors to the SMB unit.
• R1.ME1,2,4,5
• R1.ME3,6
• R2.SMB
WARNING
xx1700000005
Action Note
7 Valid for IRB 1200 Type B Tightening torque: 0.3 Nm
Tighten the connector screws.
xx1700000004
8 Refit the EIB/SMB cover to the lower arm with the Screws: 3HAB3409-207 (M3x8).
attachment screws. Tightening torque: 1.5 Nm
xx1300002427
Note
Action Note
9 Refit the fix sheet attachment screws in the lower Tightening torque: 1.5 Nm.
arm.
xx1300002426
xx1400000483
Action Note
3 Guide the cable package into the upper arm,
through the housing.
Note
4 Refit the bracket to the sheet with two screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300002424
5 Refit the fix sheet to the motor. Tightening torque: 1.5 Nm.
xx1300002423
Action Note
6 Refit the fix sheet to the inner plastic guide. Tightening torque: 1.5 Nm.
xx1300002421
7 Fit the air hose holder to the bracket. Air hose holders are included in
Replace the holder, if damaged. Cable harness material set
(3HAC049663-001).
Tightening torque: 4 Nm.
Tip
xx1300002422
xx1400001133
xx1300002420
Action Note
9 Apply grease to the cable package, cover all
moving area of the package.
xx1400000754
xx1300002371
Action Note
3 Secure the connectors to the motor with a cable
strap.
xx1300002494
Tip
xx1300002399
Action Note
3 Reconnect the FPC connectors and push them Cable layout in IRB 1200-7/0.7 :
into place inside the housing.
Tip
xx1300002412
xx1400001471
Action Note
5 For robots with protection class IP67
For robots with protection type Foundry Plus
Apply flange sealing Sikaflex 521FC on the
mounting surfaces of the small cover on the
housing.
6 Refit the small cover to the housing.
Replace if damaged.
xx1300002398
xx1600000214
Action Note
8 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
9 Check the PTFE film on the cable housing. PTFE film on lower arm cable
Replace if damaged. housing: 3HAC044710-001
xx1400000740
Action Note
10 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056724-001 (not Hygienic
robots) / 3HAC080702-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication PTFE film on cable housing cover:
For robots with protection type Hygienic 3HAC044660-001
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000048
Action Note
13 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the screws
securing the cover.
xx1300002400
Note
Connecting the air hoses and CP/CS cabling on robots not in protection type Hygienic
Use this procedure if the robot is not in protection type Hygienic.
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 Reconnect the air hoses. Air connector set with Ethernet
Replace the air hose connector set if damaged. hole in flange: 3HAC049664-001
Air connector set without Ethernet
hole in flange: 3HAC049665-001
xx1400000738
Action Note
3 If equipped, reconnect the CP/CS connector.
For robots with protection class IP67
For robots with protection type Foundry Plus
1 Check the gasket.
2 Replace if damaged.
For robots with protection type Clean Room
For robots with food grade lubrication
1 Remove residual locking liquid and other xx1500000252
pollutants with cleaning agent Loctite 7063.
On robots with protection class
2 Apply flange sealing Loctite 574 on the IP67
mounting surfaces of the CP/CS connector
and wipe clean if there is any overflowing On robots with protection type
Loctite 574. Foundry Plus
Gasket: 3HAC058567-001
xx1500000251
4 For robots with protection type Foundry Plus Protection bracket for CP/CS con-
If required, fit the protection bracket for CP/CS nectors: 3HAC058350-001
connectors.
xx1600001152
Connecting the air hoses and CP/CS cabling on robots in protection type Hygienic
Use this procedure if the robot is with protection type Hygienic.
Action Note
1 Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
Action Note
2 If the Hygienic robot not equipped with air hoses Plate without connector set:
and CP/CS cabling: 3HAC078810-001
Check the plate without connector set and the at- Gasket: 3HAC078804-001
tached gasket.
Replace if damaged.
xx2100001433
xx1400000738
xx1500000252
5 Check the connectors on the plate with connector Plate with connector set:
set and the attached gasket. 3HAC079691-001
Replace if damaged. Gasket: 3HAC078804-001
xx2100001434
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
xx1300002389
Note
Concluding procedure
Action Note
1 For robots with protection class IP67 Housing cover gasket (IRB 1200-7/0.7 ):
For robots with protection type Foundry 3HAC056698-001 (not Hygienic robots) /
Plus 3HAC080700-001 (Hygienic robots)
For robots with protection type Clean Housing cover gasket (IRB 1200-5/0.9 ):
Room 3HAC056697-001 (not Hygienic robots) /
3HAC080699-001 (Hygienic robots)
For robots with food grade lubrication
Check the gasket.
Replace if damaged.
xx1400000477
2 Refit the upper arm housing cover with the Screws: 3HAB3409-207 (M3x8).
screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300000456
Note
Action Note
3 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the upper arm housing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000215
Note
4.5.2 Replacing the swing spare parts (swing, axis-2 radial sealing)
xx1400000442 xx1400000443
3HAC059554-001 3HAC059676-001
3HAC059700-001 3HAC056215-001
Used with protection type Clean Room. Used with protection type Clean Room.
Used for robots with food grade lubrication. Used for robots with food grade lubrication.
Used with protection type Hygienic. Used with protection type Hygienic.
Replace if damaged.
Cable housing of the swing Cable housing cover of the Radial sealing with dust lip
swing
Cable housing of the swing Cable housing cover of the Radial sealing with dust lip
swing
3HAC059677-001 3HAC059678-001 3HAB3701-41
3HAC056213-001 3HAC056214-001 Not used with protection class
IP40.
Used with protection type Used with protection type
Clean Room. Clean Room. Replace if damaged.
Used for robots with food Used for robots with food
grade lubrication. grade lubrication.
Used with protection type Hy- Used with protection type Hy-
gienic. gienic.
Replace if damaged. Replace if damaged.
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cable straps -
Locking liquid 3HAB7116-1 Loctite 243
Cleaning agent - Loctite 7063
Flange sealing 12340011-116 Loctite 574
Sealant 3HAC026759-001 Sikaflex 521FC
For robots with protection type
Clean Room
For robots with food grade lubric-
ation
For robots with protection class
IP67
For robots with protection type
Foundry Plus
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
1 Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.
2 Jog all axes to zero position.
xx1300002581
Action Note
3
DANGER
4
CAUTION
xx1300002389
Action Note
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
Action Note
3 Snap loose and disconnect the axis-5 FPC
connectors.
xx1300002390
2
CAUTION
xx1400000738
xx1500000252
2
CAUTION
xx1300002400
xx1300002413
Action Note
5 Pull out the FPC connectors from the housing and Cable layout in IRB 1200-7/0.7 :
disconnect them.
xx1300002412
xx1400001471
xx1300002398
Action Note
7 Disconnect the remaining FPC connectors.
xx1300002399
2
CAUTION
CAUTION
xx1300000456
Action Note
4 Cut the strap that holds the connectors.
xx1300002494
Tip
xx1300002495
2
CAUTION
Action Note
3 Pull out the axis-3 motor connectors from the
housing and disconnect them.
xx1300002420
2
CAUTION
xx1300002422
Action Note
4 Remove the screws that fasten the fix sheet to
the inner plastic guide.
xx1300002421
xx1300002423
CAUTION
xx1300002424
Action Note
2
ELECTROSTATIC DISCHARGE (ESD)
3
CAUTION
CAUTION
CAUTION
xx1300002428
Action Note
7 Valid for IRB 1200 Type B
Loose the connector screws.
xx1700000004
xx1700000005
2
CAUTION
Action Note
4 Remove the fix sheet attachment screws in the
lower arm.
xx1300002426
CAUTION
xx1400001130
xx1600000205
Action Note
8 Remove the swing cable housing cover by remov-
ing the screws.
xx1300002431
xx1400001528
xx1300002432
Action Note
11 Pull out the cabling and then remove the axis-2
motor bracket from the cable package by remov-
ing the screws.
CAUTION
xx1300002433
xx1300002434
xx1300002435
Action Note
14 Remove the axis-2 sealing ring by removing the
screws.
xx1400000020
Tip
xx1400000023
Action Note
1
DANGER
Action Note
2
CAUTION
xx1300002551
WARNING
xx1300002552
Action Note
5 Fit guide pins to the gearbox. Guide pin for axis-2 gear unit:
3HAC049704-001
Always use three guide pins together!
xx1300002563
Tip
xx1300002553
2
CAUTION
Action Note
3 Remove the swing top cover by removing the
screws.
Tip
xx1400000447
xx1400000448
CAUTION
xx1400000449
Action Note
6 Remove the axis-1 sealing ring from the swing
and carefully run the cabling out from the swing.
xx1400000455
xx1400000450
xx1600000053
xx1600001125
Action Note
4 For robots with protection class IP67 On axis-1 sealing ring version
On axis-1 sealing ring version 3HAC044676-001, 3HAC044676-001:
3HAC058568-001 or 3HAC068107-001: Axis-1 sealing ring gasket:
For robots with protection type Foundry Plus 3HAC045685-001
On axis-1 sealing ring version 3HAC058568-001
or 3HAC068107-001:
Check the gasket on the axis-1 sealing ring.
Replace if damaged.
(See Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.)
xx1400000458
xx1600001149
xx1900001735
Action Note
5 For robots with protection class IP67 V-ring: 3HAB3732-34
On axis-1 sealing ring version 3HAC056658-001, On axis-1 sealing ring version
3HAC058568-001 or 3HAC068107-001: 3HAC056658-001:
For robots with protection type Foundry Plus
On axis-1 sealing ring version 3HAC058568-001
or 3HAC068107-001:
Check the V-ring on the axis-1 sealing ring.
(See Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.)
Replace if damaged. xx1600001124
xx1600001150
xx1900001736
6 Check the cable protection on the axis-1 sealing Cable protection: 3HAC044691-001
ring. Torx countersunk head screw
Replace if damaged. M3x5: 3HAC14286-4
If replacing the cable protection, use locking liquid Tightening torque: 0.3 Nm
Loctite 243 on the screws.
xx1400000456
Action Note
7 Fit the axis-1 sealing ring to the swing with the Axis-1 sealing ring: 3HAC044676-
screws and carefully run the cabling out up 001 / 3HAC068107-001 i
through the swing. Tightening torque: 1.5 Nm.
xx1400000455
xx1400000449
Action Note
9 Refit the swing attachment screws and washers. Screws: 3HAB3409-52 (M10x35).
Tightening torque: 40 Nm.
xx1400000448
Note
10 For robots with protection class IP67 Gasket on top swing cover:
For robots with protection type Foundry Plus 3HAC056696-001 (not Hygienic
robots) / 3HAC080698-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000425
Action Note
11 Refit the swing top cover with the screws. Cover on top of swing:
Replace if damaged. 3HAC059679-001
Cover on top of swing, Clean Room
Cover on top of swing, food grade
lubrication
Cover on top of swing, Hygienic
: 3HAC056133-001
Screws: 3HAB3409-209 (M3x20).
Tightening torque: 1.5 Nm.
xx1400000447
Note
i For information on which sealing ring to be ordered, see Spare part versions for the axis-1 sealing
ring on IP40/IP67 robots on page 878.
Refitting the axis-2 radial sealing (IP67, Foundry Plus, Clean Room, food grade lubrication, Hygienic)
Use this procedure if replacing the axis-2 radial sealing.
The sealing is only used for robots with protection class IP67, with protection type
Foundry Plus, with protection type Clean Room, with food grade lubrication and
protection type Hygienic.
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply a little grease to the sealing and wipe clean
after the refitting.
Action Note
3 Fit the axis-2 radial sealing into the cable housing. Radial sealing with dust lip:
3HAB3701-41
xx1400000450
4 Fit the circular part of the radial sealing fitting tool Axis-2 sealing assembly tool set:
against the radial sealing. 3HAC049694-001
5 Fit the tool plate to the other side of the cable
housing with the six screws M6X50.
xx1400000451
Action Note
6 Screw the screws, little by little, to press the
sealing into place.
xx1400000452
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Check the o-ring. O-ring: 3HAC048939-001
Replace if damaged.
xx1300002556
Note
xx1400001403
4 Fit guide pins to the gearbox. Guide pin for axis-2 gear unit:
3HAC049704-001
xx1300002562
Action Note
5 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-003
For robots with protection type Foundry
Plus
Check the sealing.
Replace if damaged.
CAUTION
xx1400000453
xx1300002563
Action Note
7 Refit the lower arm screws and washers, Screws: 3HAB3409-51 (M10x30).
using locking liquid Loctite 243.
Secure the screws but do not tighten yet.
xx1300002564
Note
xx1300002565
Action Note
10 For robots with protection class IP67 Gasket on swing cover: 3HAC056727-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080705-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the swing cover gasket.
Replace if damaged.
xx1400000007
xx1300002551
Action Note
12 For robots with protection type Foundry Protection plug for lifting holes:
Plus 3HAC4836-24
Check the protection plugs for lifting holes.
Replace if damaged.
xx1600001151
13 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the swing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000217
xx1600001154
xx1400000476
xx1400000457
Action Note
4 Fetch the cable housing, the plastic plate and the
axis-2 sealing ring and run the cable package
through them.
xx1400000025
5 Fasten the plastic plate to the cable housing, if The plastic plate is included in:
removed. Cable harness material set:
Replace if damaged. 3HAC049663-001.
xx1400000023
Action Note
6 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-
For robots with protection type Foundry Plus 004
Check the sealing.
Replace if damaged.
CAUTION
xx1400000454
Action Note
7 For robots with protection class IP67 Radial sealing with dust lip:
For robots with protection type Foundry Plus 3HAB3701-41
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the radial sealing.
Replace if damaged.
Note
xx1400000753
Tip
9 Refit the axis-2 sealing ring with the screws. Tightening torque: 1.5 Nm.
xx1400000020
Action Note
10 Refit the cable housing with the screws. Screws: 3HAB3409-236 (M4x10).
Tightening torque: 3 Nm.
xx1300002435
Note
xx1400000481
Action Note
12 Reconnect the motor connectors.
• R2.ME2
• R2.MP2
xx1300002434
13 Refit the axis-2 motor bracket to the cable pack- Tightening torque: 1.5 Nm.
age with the two screws.
CAUTION
xx1400000021
xx1300002432
Action Note
15 Secure the connector R2.MP2 and its cable with
cable straps onto the motor bracket. Make sure
the connector is fixed by its tab to the bracket.
xx1400001529
xx1400000482
Action Note
18 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056726-001 (not Hygienic
robots) / 3HAC080704-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000424
Action Note
21 Refit the cable housing cover. Cable housing cover of the swing:
Replace if damaged. 3HAC059678-001
Cable housing cover of the swing,
Note Clean Room
Cable housing cover of the swing,
Remember to refit the two lower screws shown food grade lubrication
in the figure. Cable housing cover of the swing,
Hygienic
: 3HAC056214-001
Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
xx1300002431
Note
22 For robots with protection type Foundry Plus Protection plug for lifting holes:
Check the protection plugs for lifting holes. 3HAC4836-24
Replace if damaged.
xx1600001151
Action Note
23 For robots with protection type Clean Room Swing sealing plug:3HAC053687-
For robots with food grade lubrication 001
For robots with protection type Hygienic
Refit the swing sealing plug.
Follow the procedure specified in Refitting the
swing sealing plug on page 167.
xx1600000205
24 Refit the lower arm bracket to the cable package. Tightening torque: 1.5 Nm.
CAUTION
xx1300002430
Action Note
3 For robots with protection class IP67 Gasket on EIB/SMB cover:
For robots with protection type Foundry Plus 3HAC056728-001 (not Hygienic
robots) / 3HAC080706-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the EIB/SMB cover gasket.
Replace if damaged.
xx1400000475
WARNING
5 Valid for IRB 1200 (no type specified) and IRB xx1300002428
1200 Type A
Connect the lugs to the EIB/SMB cover.
6 Valid for IRB 1200 Type B
Connect the connectors to the SMB unit.
• R1.ME1,2,4,5
• R1.ME3,6
• R2.SMB
WARNING
xx1700000005
Action Note
7 Valid for IRB 1200 Type B Tightening torque: 0.3 Nm
Tighten the connector screws.
xx1700000004
8 Refit the EIB/SMB cover to the lower arm with the Screws: 3HAB3409-207 (M3x8).
attachment screws. Tightening torque: 1.5 Nm
xx1300002427
Note
Action Note
9 Refit the fix sheet attachment screws in the lower Tightening torque: 1.5 Nm.
arm.
xx1300002426
xx1400000483
Action Note
3 Guide the cable package into the upper arm,
through the housing.
Note
4 Refit the bracket to the sheet with two screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300002424
5 Refit the fix sheet to the motor. Tightening torque: 1.5 Nm.
xx1300002423
Action Note
6 Refit the fix sheet to the inner plastic guide. Tightening torque: 1.5 Nm.
xx1300002421
7 Fit the air hose holder to the bracket. Air hose holders are included in
Replace the holder, if damaged. Cable harness material set
(3HAC049663-001).
Tightening torque: 4 Nm.
Tip
xx1300002422
xx1400001133
xx1300002420
Action Note
9 Apply grease to the cable package, cover all
moving area of the package.
xx1400000754
xx1300002371
Action Note
3 Secure the connectors to the motor with a cable
strap.
xx1300002494
Tip
xx1300002399
Action Note
3 Reconnect the FPC connectors and push them Cable layout in IRB 1200-7/0.7 :
into place inside the housing.
Tip
xx1300002412
xx1400001471
Action Note
5 For robots with protection class IP67
For robots with protection type Foundry Plus
Apply flange sealing Sikaflex 521FC on the
mounting surfaces of the small cover on the
housing.
6 Refit the small cover to the housing.
Replace if damaged.
xx1300002398
xx1600000214
Action Note
8 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
9 Check the PTFE film on the cable housing. PTFE film on lower arm cable
Replace if damaged. housing: 3HAC044710-001
xx1400000740
Action Note
10 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056724-001 (not Hygienic
robots) / 3HAC080702-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication PTFE film on cable housing cover:
For robots with protection type Hygienic 3HAC044660-001
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000048
Action Note
13 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the screws
securing the cover.
xx1300002400
Note
Connecting the air hoses and CP/CS cabling on robots not in protection type Hygienic
Use this procedure if the robot is not in protection type Hygienic.
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 Reconnect the air hoses. Air connector set with Ethernet
Replace the air hose connector set if damaged. hole in flange: 3HAC049664-001
Air connector set without Ethernet
hole in flange: 3HAC049665-001
xx1400000738
Action Note
3 If equipped, reconnect the CP/CS connector.
For robots with protection class IP67
For robots with protection type Foundry Plus
1 Check the gasket.
2 Replace if damaged.
For robots with protection type Clean Room
For robots with food grade lubrication
1 Remove residual locking liquid and other xx1500000252
pollutants with cleaning agent Loctite 7063.
On robots with protection class
2 Apply flange sealing Loctite 574 on the IP67
mounting surfaces of the CP/CS connector
and wipe clean if there is any overflowing On robots with protection type
Loctite 574. Foundry Plus
Gasket: 3HAC058567-001
xx1500000251
4 For robots with protection type Foundry Plus Protection bracket for CP/CS con-
If required, fit the protection bracket for CP/CS nectors: 3HAC058350-001
connectors.
xx1600001152
Connecting the air hoses and CP/CS cabling on robots in protection type Hygienic
Use this procedure if the robot is with protection type Hygienic.
Action Note
1 Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
Action Note
2 If the Hygienic robot not equipped with air hoses Plate without connector set:
and CP/CS cabling: 3HAC078810-001
Check the plate without connector set and the at- Gasket: 3HAC078804-001
tached gasket.
Replace if damaged.
xx2100001433
xx1400000738
xx1500000252
5 Check the connectors on the plate with connector Plate with connector set:
set and the attached gasket. 3HAC079691-001
Replace if damaged. Gasket: 3HAC078804-001
xx2100001434
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
xx1300002389
Note
Concluding procedure
Action Note
1 For robots with protection class IP67 Housing cover gasket (IRB 1200-7/0.7 ):
For robots with protection type Foundry 3HAC056698-001 (not Hygienic robots) /
Plus 3HAC080700-001 (Hygienic robots)
For robots with protection type Clean Housing cover gasket (IRB 1200-5/0.9 ):
Room 3HAC056697-001 (not Hygienic robots) /
3HAC080699-001 (Hygienic robots)
For robots with food grade lubrication
Check the gasket.
Replace if damaged.
xx1400000477
2 Refit the upper arm housing cover with the Screws: 3HAB3409-207 (M3x8).
screws. Tightening torque: 1.5 Nm.
CAUTION
xx1300000456
Note
Action Note
3 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the upper arm housing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000215
Note
xx1400000391
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Action Note
1 Jog the robot to a position where the
mechanical stop is most easily accessed.
2
DANGER
3
CAUTION
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the mechanical stop by removing
the screw.
4 Discard the old screw and washer.
5 Refit and secure the new stop with the en-
closed screw and washer.
xx1400000392
Note
Note
7
DANGER
xx1300002547
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Continues on next page
642 Product manual - IRB 1200
3HAC046983-001 Revision: S
© Copyright 2014 - 2021 ABB. All rights reserved.
4 Repair
4.6.2 Replacing the axis-2 drive unit
Continued
Information about valid calibration method is found on the calibration label or in the calibration
menu on the FlexPendant.
If no data is found related to standard calibration, manual calibration is used as default.
Required consumables
Consumable Art. no. Note
Cable straps -
Cleaning agent - Loctite 7063
Flange sealing 12340011-116 Loctite 574
Locking liquid 3HAB7116-1 Loctite 243
Harmonic grease 4B No. 2 3HAC037302-001 Total amount: 60 g.
Used to lubricate the gearbox.
The gear is pre-filled at delivery
but grease may need to be added
depending on the actual condi-
tion.
LUBRIPLATE SYNXTREME FG-0 3HAC043771-001 Total amount: 60 g.
Used to lubricate the gearbox of
robots with food grade lubrication
and robots with protection type
Hygienic.
The gear is pre-filled at delivery
but grease may need to be added
depending on the actual condi-
tion.
Sealant 3HAC026759-001 Sikaflex 521FC
For robots with protection type
Clean Room.
For robots with food grade lubric-
ation.
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
Action Note
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
xx1300002581
3
DANGER
Action Note
4
CAUTION
5
CAUTION
Action Note
1
DANGER
2
CAUTION
Action Note
3 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Remove the swing sealing plug.
Follow the procedure specified in Remov-
ing the swing sealing plug on page 166.
xx1600000205
xx1300002431
xx1400001528
Action Note
6 Remove the axis-2 motor bracket screws.
xx1300002432
xx1300002434
Note
xx1300002548
Action Note
9 Loosen the cable housing of the swing by
removing the screws, and tilt it outwards.
CAUTION
xx1300002549
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the swing cover.
xx1300002551
WARNING
xx1300002552
Action Note
5 Fit guide pins to the gearbox. Guide pin for axis-2 gear unit:
3HAC049704-001
Always use three guide pins together!
xx1300002563
Tip
xx1300002553
Action Note
1
DANGER
2
CAUTION
Action Note
3
CAUTION
WARNING
xx1400000008
xx1300002555
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check if there is a sufficient amount of Harmonic grease 4B No. 2: 3HAC037302-
grease on the gear. Apply more grease, if 001
needed. For robots with food grade lubrication
For robots with protection type Hygienic
LUBRIPLATE SYNXTREME FG-0:
3HAC043771-001
3 For robots with protection class IP67
For robots with protection type Foundry
Plus
Remove residual locking liquid and other
pollutants with cleaning agent Loctite 7063.
Apply flange sealing Loctite 574 on the
mounting surfaces of the lower arm.
xx1400000006
Action Note
4 Carefully insert the complete drive unit.
Note
xx1300002580
xx1400000795
xx1300002554
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check the o-ring. O-ring: 3HAC048939-001
Replace if damaged.
xx1300002556
Note
xx1400001403
Action Note
4 Fit guide pins to the gearbox. Guide pin for axis-2 gear unit:
3HAC049704-001
xx1300002562
CAUTION
xx1400000453
xx1300002563
Action Note
7 Refit the lower arm screws and washers, Screws: 3HAB3409-51 (M10x30).
using locking liquid Loctite 243.
Secure the screws but do not tighten yet.
xx1300002564
Note
xx1300002565
Action Note
10 For robots with protection class IP67 Gasket on swing cover: 3HAC056727-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080705-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the swing cover gasket.
Replace if damaged.
xx1400000007
xx1300002551
Action Note
12 For robots with protection type Foundry Protection plug for lifting holes:
Plus 3HAC4836-24
Check the protection plugs for lifting holes.
Replace if damaged.
xx1600001151
13 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the swing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000217
xx1600001154
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the cable housing to the swing with Tightening torque: 3 Nm.
the screws.
xx1300002549
xx1300002548
Action Note
4 Reconnect the motor connectors.
• R2.ME2
• R2.MP2
xx1300002434
xx1300002432
xx1400001529
Action Note
7 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry 3HAC056726-001 (not Hygienic robots) /
Plus 3HAC080704-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the cable housing
cover.
Replace if damaged.
8 Check the PTFE film. PTFE film on cable housing cover:
Replace if damaged. 3HAC044660-001
xx1300002431
Note
Action Note
11 For robots with protection type Clean Swing sealing plug:3HAC053687-001
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Refit the swing sealing plug.
Follow the procedure specified in Refitting
the swing sealing plug on page 167.
xx1600000205
Concluding procedure
Action Note
1 Remove the lifting slings from the robot.
2 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean, seal and paint the joints that have
been opened. See Cut the paint or surface
on the robot before replacing parts on
page 158.
Note
xx1300002527
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cleaning agent - Isopropanol
Locking liquid 3HAB7116-1 Loctite 243
Flange sealing 12340011-116 Loctite 574
For robots with protection class
IP67
For robots with protection type
Foundry Plus
Sealant 3HAC026759-001 Sikaflex 521FC
For robots with protection type
Clean Room.
For robots with food grade lubric-
ation.
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
Harmonic grease 4B No. 2 3HAC037302-001 Total amount: 32 g.
Used to lubricate the gearbox.
The gear is pre-filled at delivery
but grease may need to be added
depending on the actual condi-
tion.
LUBRIPLATE SYNXTREME FG-0 3HAC043771-001 Total amount: 32 g.
Used to lubricate the gearbox of
robots with food grade lubrication
and robots with protection type
Hygienic.
The gear is pre-filled at delivery
but grease may need to be added
depending on the actual condi-
tion.
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
xx1300002581
Action Note
3
DANGER
4
CAUTION
xx1300002400
xx1300002413
2
CAUTION
xx1300002420
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the screws that fasten the fix sheet
to the inner plastic guide.
xx1300002421
xx1300002423
Note
xx1300002530
Action Note
6 Remove the cable housing of the lower arm
by removing the screws, and tilt it out-
wards.
xx1400000785
Action Note
1
DANGER
2
CAUTION
Action Note
3 Remove the lower arm cover.
xx1300002528
4
CAUTION
WARNING
xx1300002531
Action Note
7 Fit guide pins to the upper arm. Guide pin for upper arm: 3HAC049705-001
Always use three guide pins together!
xx1400000771
xx1300002533
2
CAUTION
Action Note
3 Remove the drive unit screws.
xx1300002532
CAUTION
xx1300002534
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check if there is a sufficient amount of Harmonic grease 4B No. 2: 3HAC037302-
grease on the gear. Apply more grease, if 001.
needed. For robots with food grade lubrication
For robots with protection type Hygienic
LUBRIPLATE SYNXTREME FG-0:
3HAC043771-001
Action Note
3 Check the o-ring for damage. Replace if O-ring: 3HAC048939-002
damaged.
xx1400000004
xx1400000784
Note
xx1300002534
Action Note
7 Refit the drive unit screws. Screws: 3HAB3409-214 (M4x40)
Tightening torque: 4.5 Nm
xx1300002532
Note
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Fit guide pins to the axis-3 gear unit. Guide pin for upper arm: 3HAC049705-001
Always use three guide pins together!
xx1400000027
CAUTION
xx1400000474
Action Note
4 Refit the upper arm to the lower arm and Screws: 3HAB3409-213 (M4x25).
secure with the upper arm screws and
washers. Do not tighten yet.
xx1400000028
Note
xx1400000029
Action Note
7 For robots with protection class IP67 Gasket on lower arm cover: 3HAC056725-
For robots with protection type Foundry 001 (not Hygienic robots) / 3HAC080703-
Plus 001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the lower arm cover gasket.
Replace if damaged.
xx1400000047
xx1300002528
Note
Action Note
9 For robots with protection class IP67 Gasket on lower arm cable housing:
For robots with protection type Foundry 3HAC044895-001 (not Hygienic robots) /
Plus 3HAC080696-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the cable housing gasket.
Replace if damaged.
xx1400000414
CAUTION
Note
Action Note
11 Refit the cable housing of the lower arm. Tightening torque: 3 Nm
xx1400000785
12 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the cable housing of the lower arm. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
Note
xx1600001155
Concluding procedure
Action Note
1 Refit the fix sheet to the motor. Tightening torque: 1.5 Nm.
xx1300002423
2 Refit the fix sheet to the inner plastic guide. Tightening torque: 1.5 Nm.
xx1300002421
xx1300002420
Action Note
4 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
5 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry 3HAC056724-001 (not Hygienic robots) /
Plus 3HAC080702-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the cable housing
cover.
Replace if damaged.
xx1400000048
Action Note
6 Check the PTFE film on the cable housing PTFE film on cable housing cover:
cover. 3HAC044660-001
Replace if damaged.
7 Apply grease to the inner surface of the
cable housing cover and the PTFE film
surface.
8 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry
Plus
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the
screws securing the cover.
xx1300002400
Note
Note
Action Note
11
DANGER
xx1300002462
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cable straps -
Cleaning agent - Loctite 7063
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
xx1300002581
3
DANGER
4
CAUTION
Action Note
2
CAUTION
xx1300002349
xx1600001148
xx2100001406
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
Action Note
3 Loosen the screws so that the motor can
be moved sideways.
xx1300002350
xx1300002351
xx1300002390
xx1300002352
2
CAUTION
xx1300002353
xx1300002355
xx1300002356
Action Note
6 Guide the hoses through the plate hole and re-
move the plate.
xx1300002357
xx1300002358
CAUTION xx1300002359
xx1300002611
2
CAUTION
CAUTION
xx1300000456
xx1300002494
Action Note
5 Disconnect the motor connectors.
Tip
xx1300002495
2
CAUTION
xx1300002400
Action Note
4 Remove the plate.
xx1300002413
5 Pull out the FPC connectors from the housing and Cable layout in IRB 1200-7/0.7 :
disconnect them.
xx1300002412
xx1400001471
Action Note
6 Remove the small cover of the housing.
xx1300002398
xx1300002399
Action Note
1
DANGER
2
CAUTION
Action Note
3 Loosen the two attachment screws and
move the motor downwards to slacken the
timing belt.
xx1300002524
xx1300002522
Action Note
1
DANGER
Action Note
2
CAUTION
xx1400000797
2
CAUTION
Action Note
3 Remove the axis-4 FPC unit screws.
xx1300002373
xx1600000262
xx1300002372
xx1300002374
Action Note
1
DANGER
Action Note
2
CAUTION
xx1300002376
xx1400002400
xx1300002387
Action Note
1
DANGER
2
CAUTION
xx1300002378
xx1300002379
Action Note
5 Remove the pulley from the gear by remov-
ing its attachment screws.
xx1300002380
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the pulley to the gear and secure with Screws: 3HAB3409-209 (M3x20).
its attachment screws. Tightening torque: 1.1 Nm.
xx1300002380
Note
Action Note
3 Refit the gear to the housing.
xx1300002379
xx1300002378
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 If replacing the drive shaft with a new spare Screws: 3HAB3409-207 (M3x8).
part, remove the sleeve from the old shaft Tightening torque: 1.5 Nm.
and fit it to the new shaft.
Also move the screw on top of the old drive
shaft to the new shaft.
xx1300002387
xx1300002377
xx1300002376
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection class IP67 M2 variseal sealing: 3HAC044641-007
For robots with protection type Foundry
Plus
Check the sealing.
Replace if damaged.
CAUTION
xx1300002418
3 For robots with protection class IP67 Radial sealing with dust lip: 3HAB3701-48
For robots with protection type Foundry
Plus
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the radial sealing.
Replace if damaged, as described below.
In order to replace the radial sealing, both
the axis-4 mechanical stop and the axis-4
FPC unit must be removed from the hous-
ing extender unit, if not already removed.
xx1400000438
Action Note
5 Fit the radial sealing into the housing ex-
tender unit.
6 Fit the circular part of the radial sealing Axis-4 sealing assembly tool set:
assembly tool against the radial sealing. 3HAC049699-001
7 Fit the tool plate to the other side of the
housing extender unit with the six screws
M6X50.
xx1400000436
xx1400000437
Action Note
2 For robots with protection class IP67
For robots with protection type Foundry Plus
Remove residual locking liquid and other pollut-
ants with cleaning agent Loctite 7063.
Apply flange sealing Loctite 574 on the mounting
surfaces of the housing extender unit.
xx1300002613
xx1600000216
CAUTION
Note
xx1300002372
Action Note
6 For robots with protection type Foundry Plus Screw sealing plug: 3HAC053685-
For robots with protection type Clean Room 001
For robots with food grade lubrication
For robots with protection type Hygienic
Press in screw sealing plugs to cover the screws.
xx1600000263
7 Fit and secure the axis-4 FPC unit screws. Tightening torque: 0.3 Nm.
xx1300002373
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Place the timing belt at the gear pulley and
run the air hoses through the belt.
3 Install the air hoses in and through the
housing extender unit.
Action Note
4 Refit the plastic protection plate with its
screws.
xx1400000797
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check that:
• all assembly surfaces are clean and
undamaged.
• the motor is clean and undamaged.
3 Fit the timing belt to the motor pulley.
Action Note
4 Place the motor at its mounting position Screws: 3HAB3409-14 (M5x16).
and fasten the attachment screws and
washers just enough to still be able to
move the motor.
Position the robot with the connectors dir-
ected as shown in the figure.
Verify that the top surface of the axis-4
motor is parallel with the mounting flange
surface on the housing, shown in the figure,
when moving the motor.
xx1300002524
Note
xx1300002612
xx1300002525
Action Note
6 Move the motor to achieve correct belt Belt tension: F = 30 N.
tension (F = 30 N).
7 Secure the motor with its attachment Tightening torque: 6 Nm.
screws.
Tip
xx1300002399
3 Reconnect the FPC connectors and push them Cable layout in IRB 1200-7/0.7 :
into place inside the housing.
Tip
xx1300002412
xx1400001471
Action Note
5 For robots with protection class IP67
For robots with protection type Foundry Plus
Apply flange sealing Sikaflex 521FC on the
mounting surfaces of the small cover on the
housing.
6 Refit the small cover to the housing.
Replace if damaged.
xx1300002398
xx1600000214
Action Note
8 Refit the plate. Tightening torque: 1.5 Nm.
xx1300002413
9 Check the PTFE film on the cable housing. PTFE film on lower arm cable
Replace if damaged. housing: 3HAC044710-001
xx1400000740
Action Note
10 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry Plus 3HAC056724-001 (not Hygienic
robots) / 3HAC080702-001 (Hygien-
For robots with protection type Clean Room ic robots)
For robots with food grade lubrication PTFE film on cable housing cover:
For robots with protection type Hygienic 3HAC044660-001
Check the gasket of the cable housing cover.
Replace if damaged.
xx1400000048
Action Note
13 Refit the cable housing cover. Screws: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry Plus
For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the screws
securing the cover.
xx1300002400
Note
xx1300002371
Action Note
3 Secure the connectors to the motor with a cable
strap.
xx1300002494
CAUTION xx1300002359
xx1300002611
Action Note
3 Refit the washer while at the same time putting Washer: 3HAC044869-001
the cables through its center.
Replace washer, if damaged.
xx1400000001
4 Refit the screw M6x35 (1 pc). Do not tighten yet. Screw: 3HAB3409-238 (M6x35 (1
pc)).
xx1400000002
Note
5 Refit the rest of the screws (M5x35 (7 pcs)). Screw: 3HAB3409-237 (M5x35 (7
pcs)).
xx1400000003
Note
Action Note
7 Put the cables through the plate hole and refit the Tightening torque: 0.3 Nm.
plate.
xx1300002356
CAUTION
xx1300002355
xx1300002353
Action Note
3 Place the motor at its mounting position and Screws: 3HAB3409-212 (M4x16).
fasten the attachment screws and washers just
enough to still be able to move the motor.
xx1300002463
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the timing belt on the pulley.
xx1300002351
Action Note
4 Secure the motor with its attachment
screws.
xx1300002350
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
Action Note
2 Reconnect the motor cables.
• R3.MP5
• R3.ME5
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
Action Note
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
Concluding procedure
Action Note
1 For robots with protection class IP67 Housing cover gasket (IRB 1200-
For robots with protection type Foundry Plus 7/0.7 ): 3HAC056698-001 (not Hy-
gienic robots) / 3HAC080700-001
For robots with protection type Clean Room (Hygienic robots)
For robots with food grade lubrication Housing cover gasket (IRB 1200-
For robots with protection type Hygienic 5/0.9 ): 3HAC056697-001 (not Hy-
Check the gasket. gienic robots) / 3HAC080699-001
Replace if damaged. (Hygienic robots)
xx1400000477
2 Refit the upper arm housing cover with the Screws: 3HAB3409-207 (M3x8).
screws. Tightening torque: 1.5 Nm.
xx1300000456
Note
3 For robots with protection type Clean Room For robots with protection type
For robots with food grade lubrication Clean Room
For robots with protection type Hygienic For robots with food grade lubric-
ation
Apply a string of the sealant to the joint of the
upper arm housing cover. Sealant, SikaFlex 521FC
Smooth out the sealant string using a finger tip. For robots with protection type
Use washing-up on finger tips to get a smooth Hygienic
joint. Sealant, Trans Clear
If necessary, add extra sealant to get a full cover
joint.
xx1600000215
Action Note
4 For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean, seal and paint the joints that have been
opened. See Cut the paint or surface on the robot
before replacing parts on page 158.
Note
Location of motor
The axis-4 motor is located as shown in the figure.
xx1300002474
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cleaning agent - Isopropanol
Cable straps -
Sealant 3HAC026759-001 Sikaflex 521FC
For robots with protection type
Clean Room.
For robots with food grade lubric-
ation.
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
Action Note
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
xx1300002581
3
DANGER
Action Note
4
CAUTION
2
CAUTION
CAUTION
xx1300000456
Action Note
4 Cut the strap that holds the connectors.
xx1300002494
Tip
xx1300002495
Action Note
1
DANGER
2
CAUTION
Action Note
3 Loosen the two attachment screws and
move the motor downwards to slacken the
timing belt.
xx1300002524
xx1300002522
Action Note
1
DANGER
Action Note
2
CAUTION
xx1300002523
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
Action Note
2 Refit the motor flange and bracket to the motor Motor flange: 3HAC047479-001
with the screws. Screws: 3HAB3409-14 (M5x16).
Replace the flange if damaged. Tightening torque: 6 Nm.
xx1300002523
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check that:
• all assembly surfaces are clean and
undamaged.
• the motor is clean and undamaged.
3 Fit the timing belt to the motor pulley.
Action Note
4 Place the motor at its mounting position Screws: 3HAB3409-14 (M5x16).
and fasten the attachment screws and
washers just enough to still be able to
move the motor.
Position the robot with the connectors dir-
ected as shown in the figure.
Verify that the top surface of the axis-4
motor is parallel with the mounting flange
surface on the housing, shown in the figure,
when moving the motor.
xx1300002524
Note
xx1300002612
xx1300002525
Action Note
6 Move the motor to achieve correct belt Belt tension: F = 30 N.
tension (F = 30 N).
7 Secure the motor with its attachment Tightening torque: 6 Nm.
screws.
xx1300002371
xx1300002494
Concluding procedure
Action Note
1 For robots with protection class IP67 Housing cover gasket (IRB 1200-7/0.7 ):
For robots with protection type Foundry 3HAC056698-001 (not Hygienic robots) /
Plus 3HAC080700-001 (Hygienic robots)
For robots with protection type Clean Housing cover gasket (IRB 1200-5/0.9 ):
Room 3HAC056697-001 (not Hygienic robots) /
3HAC080699-001 (Hygienic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000477
2 Refit the upper arm housing cover with the Screws: 3HAB3409-207 (M3x8).
screws. Tightening torque: 1.5 Nm.
xx1300000456
Note
Action Note
3 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the upper arm housing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000215
Note
xx1400000036
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cleaning agent - Isopropanol
Cable straps -
Cleaning agent - Loctite 7063
Flange sealing 12340011-116 Loctite 574
For robots with protection type
Clean Room.
For robots with food grade lubric-
ation.
Sealant 3HAC026759-001 Sikaflex 521FC
For robots with protection type
Clean Room.
For robots with food grade lubric-
ation.
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
Locking liquid 3HAB7116-1 Loctite 243
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
xx1300002581
Action Note
3
DANGER
4
CAUTION
xx1300002400
xx1300002389
Action Note
7 Disconnect the air hoses.
xx1400002327
2
CAUTION
CAUTION
xx1300000456
Action Note
4 Cut the strap that holds the connectors.
xx1300002494
Tip
xx1300002495
Action Note
1
DANGER
2
CAUTION
Action Note
3 Loosen the two attachment screws and
move the motor downwards to slacken the
timing belt.
xx1300002524
xx1300002522
Action Note
1
DANGER
Action Note
2
CAUTION
xx1400000797
2
CAUTION
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Place the timing belt at the gear pulley and
run the air hoses through the belt.
3 Install the air hoses in and through the
housing extender unit.
4 Refit the plastic protection plate with its
screws.
xx1400000797
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Check that:
• all assembly surfaces are clean and
undamaged.
• the motor is clean and undamaged.
3 Fit the timing belt to the motor pulley.
Action Note
4 Place the motor at its mounting position Screws: 3HAB3409-14 (M5x16).
and fasten the attachment screws and
washers just enough to still be able to
move the motor.
Position the robot with the connectors dir-
ected as shown in the figure.
Verify that the top surface of the axis-4
motor is parallel with the mounting flange
surface on the housing, shown in the figure,
when moving the motor.
xx1300002524
Note
xx1300002612
xx1300002525
Action Note
6 Move the motor to achieve correct belt Belt tension: F = 30 N.
tension (F = 30 N).
7 Secure the motor with its attachment Tightening torque: 6 Nm.
screws.
xx1300002371
xx1300002494
Connecting the air hoses and CP/CS cabling on robots not in protection type Hygienic
Use this procedure if the robot is not in protection type Hygienic.
Action Note
1 For robots with protection type Clean Room
For robots with food grade lubrication
Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 Reconnect the air hoses. Air connector set with Ethernet
Replace the air hose connector set if damaged. hole in flange: 3HAC049664-001
Air connector set without Ethernet
hole in flange: 3HAC049665-001
xx1400000738
xx1500000251
Action Note
4 For robots with protection type Foundry Plus Protection bracket for CP/CS con-
If required, fit the protection bracket for CP/CS nectors: 3HAC058350-001
connectors.
xx1600001152
Connecting the air hoses and CP/CS cabling on robots in protection type Hygienic
Use this procedure if the robot is with protection type Hygienic.
Action Note
1 Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.
2 If the Hygienic robot not equipped with air hoses Plate without connector set:
and CP/CS cabling: 3HAC078810-001
Check the plate without connector set and the at- Gasket: 3HAC078804-001
tached gasket.
Replace if damaged.
xx2100001433
xx1400000738
xx1500000252
Action Note
5 Check the connectors on the plate with connector Plate with connector set:
set and the attached gasket. 3HAC079691-001
Replace if damaged. Gasket: 3HAC078804-001
xx2100001434
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
3 Refit the cover to the cable housing. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
xx1300002389
Note
Concluding procedure
Action Note
1 For robots with protection class IP67 Housing cover gasket (IRB 1200-7/0.7 ):
For robots with protection type Foundry 3HAC056698-001 (not Hygienic robots) /
Plus 3HAC080700-001 (Hygienic robots)
For robots with protection type Clean Housing cover gasket (IRB 1200-5/0.9 ):
Room 3HAC056697-001 (not Hygienic robots) /
3HAC080699-001 (Hygienic robots)
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket.
Replace if damaged.
xx1400000477
Action Note
2 Refit the upper arm housing cover with the Screws: 3HAB3409-207 (M3x8).
screws. Tightening torque: 1.5 Nm.
xx1300000456
Note
3 For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
For robots with protection type Hygienic Sealant, SikaFlex 521FC
Apply a string of the sealant to the joint of For robots with protection type Hygienic
the upper arm housing cover. Sealant, Trans Clear
Smooth out the sealant string using a finger
tip. Use washing-up on finger tips to get a
smooth joint.
If necessary, add extra sealant to get a full
cover joint.
xx1600000215
Action Note
4 For robots with protection class IP67 Gasket on cable housing cover:
For robots with protection type Foundry 3HAC056724-001 (not Hygienic robots) /
Plus 3HAC080702-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the cable housing
cover.
Replace if damaged.
xx1400000048
5 Check the PTFE film on the cable housing PTFE film on cable housing cover:
cover. 3HAC044660-001
Replace if damaged.
6 Apply grease to the inner surface of the
cable housing cover and the PTFE film
surface.
Action Note
7 Refit the cable housing cover. Tightening torque: 3HAB3409-207 (M3x8).
For robots with protection class IP67 Tightening torque: 1.5 Nm
For robots with protection type Foundry
Plus
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Apply locking liquid Loctite 243 to all the
screws securing the cover.
xx1300002400
Note
Note
Location of motor
The axis-5 motor is located as shown in the figure.
xx1300002473
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cleaning agent - Isopropanol
Locking liquid 3HAB7116-1 Loctite 243
For robots with protection class
IP67
For robots with protection type
Foundry Plus
Sealant 3HAC073510-001 Trans Clear
For robots with protection type
Hygienic
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
Action Note
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
xx1300002581
3
DANGER
4
CAUTION
2
CAUTION
Action Note
3 Remove the covers on each side of the wrist by
removing their screws.
For robots with protection class
Note IP67
For robots with protection type
For robots with protection class IP67 Foundry Plus
For robots with protection type Foundry Plus
The two front screws on the left hand side cover
(encircled in the figure) have been fitted with
locking liquid.
The tubular cover (left hand side cover) has two
extra screws and washers, as encircled in the
figure.
xx1300002349
xx1600001148
xx2100001406
Action Note
2
CAUTION
Tip
Action Note
1
DANGER
2
CAUTION
xx1300002350
Action Note
4 Remove the timing belt.
xx1300002351
xx1300002390
xx1300002352
Action Note
3 Place the motor at its mounting position and Screws: 3HAB3409-212 (M4x16).
fasten the attachment screws and washers just
enough to still be able to move the motor.
xx1300002463
Note
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the timing belt on the pulley.
xx1300002351
Action Note
4 Secure the motor with its attachment
screws.
xx1300002350
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
Action Note
2 Reconnect the motor cables.
• R3.MP5
• R3.ME5
xx1300002360
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
Action Note
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
Concluding procedure
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean, seal and paint the joints that have
been opened. See Cut the paint or surface
on the robot before replacing parts on
page 158.
Note
xx1400000032
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cleaning agent - Isopropanol
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
1 Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.
Action Note
2 Jog all axes to zero position.
xx1300002581
3
DANGER
4
CAUTION
xx1400000033
Action Note
1
DANGER
2
CAUTION
xx1300002350
xx1300002351
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the timing belt on the pulley.
xx1300002351
xx1300002350
Concluding procedure
Action Note
1 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the gasket of the wrist cover.
Replace if damaged.
xx1400000034
xx1400000033
Note
Note
Action Note
5
DANGER
xx1300002467
Note
The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,
www.abb.com/myABB.
Required consumables
Consumable Art. no. Note
Cleaning agent - Loctite 7063
Locking liquid 3HAB7116-1 Loctite 243
Flange sealing 12340011-116 Loctite 574
For robots with protection class
IP67
For robots with protection type
Foundry Plus
Flange sealing 3HAC026759-003 Sikaflex 521FC
If the robot is to be calibrated with refer- Follow the instructions given in the refer-
ence calibration: ence calibration routine on the FlexPendant
Find previous reference values for the axis to create reference values.
or create new reference values. These val- Creating new values requires possibility to
ues are to be used after the repair proced- move the robot.
ure is completed, for calibration of the ro- Read more about reference calibration for
bot. Axis Calibration in Reference calibration
If no previous reference values exist, and routine on page 819.
no new reference values can be created,
then reference calibration is not possible.
If the robot is to be calibrated with fine
calibration:
Remove all external cable packages
(DressPack) and tools from the robot.
Action Note
1 Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.
Action Note
2 Jog all axes to zero position.
xx1300002581
3
DANGER
4
CAUTION
2
CAUTION
Action Note
3 Remove the covers on each side of the wrist by
removing their screws.
For robots with protection class
Note IP67
For robots with protection type
For robots with protection class IP67 Foundry Plus
For robots with protection type Foundry Plus
The two front screws on the left hand side cover
(encircled in the figure) have been fitted with
locking liquid.
The tubular cover (left hand side cover) has two
extra screws and washers, as encircled in the
figure.
xx1300002349
xx1600001148
xx2100001406
Action Note
2
CAUTION
xx1300002390
xx1300002391
Note
xx1300002392
Action Note
2
CAUTION
xx1300002393
xx1300002582
xx1300002394
Action Note
6 Disconnect the axis-6 motor connectors and re-
move the FPC unit completely.
xx1300002395
2
CAUTION
xx1300002350
xx1300002351
Action Note
5 Support the weight of the drive unit and remove
the screws.
xx1300002469
6 Fit guide pins to the gearbox. Guide pin for tilt unit (axis 5):
3HAC049706-001
Always use three guide pins togeth-
er!
xx1400000775
xx1300002470
Action Note
2 Check the gasket (A), seal ring unit (B) and
stainless shaft (C) on the tool flange.
Replace if damaged, as described below.
If undamaged and properly seated, skip to the
next procedure table.
xx2100001448
xx2100001449
xx2100001450
xx2100001451
5 Place the flange tightening tool together with a Flange tightening tool:
3/8" (10 mm) socket spanner on the seal ring unit 3HAC079686-001
and loosen the unit.
xx2100001452
Action Note
6 Remove the gasket and seal ring unit.
xx2100001453
xx2100001454
xx2100001453
xx2100001455
Action Note
10 Place the flange tightening tool together with a Flange tightening tool:
3/8" (10 mm) socket spanner on the seal ring unit 3HAC079686-001
and tighten the unit. Tightening torque: 6 Nm
xx2100001456
11 Fit two guide pins to the tool flange. Guide pin for stainless shaft on tool
flange: 3HAC079684-001
xx2100001457
xx2100001458
xx2100001459
Action Note
14 Remove the guide pins.
xx2100001460
xx1600001126
CAUTION
xx1300002493
Action Note
4 Remove residual locking liquid and other pollut- For robots not in protection type
ants with cleaning agent Loctite 7063. Hygienic
Apply flange sealing on the mounting surfaces of Flange sealant, SikaFlex 521FC
the drive unit. For robots with protection type
Hygienic
Note Flange sealant, Trans Clear
xx1400001404
5 Fit guide pins to the axis-5 gearbox. Guide pin for tilt unit (axis 5):
3HAC049706-001
xx1300002568
Action Note
6 For robots with protection type Clean Room
For robots with food grade lubrication
Make sure the sealing to the tilt covers is intact
before the refitting.
For robots with protection type Hygienic
Hygienic robots do not have tilt covers.
xx1600000219
xx1600000220
7 Refit the drive unit and secure with the screws Attachment screws: 3HAB3409-236
and washers. (M4x10).
Secure the screws but do not tighten yet.
Note
xx1300002569
Note
xx1300002570
Action Note
9 Cross-tighten all the screws with torque 1 Nm first,
then with 2 Nm, with 4 Nm, and finally with 4.5
Nm.
Action Note
1
WARNING
xx1300002395
4 Carefully refit the FPC unit and secure with Tightening torque: 0.3 Nm.
screws.
Note
xx1300002394
Action Note
5 For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
For robots with protection type Hygienic Flange sealing, Loctite 574
Remove residual locking liquid and other For robots with protection type Hygienic
pollutants with cleaning agent Loctite 7063. Flange sealing, Trans Clear
Apply flange sealing on the mounting sur-
faces of the sleeve.
Note
xx1300002609
xx1300002393
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
Action Note
2 Check the sealing. M2 variseal sealing: 3HAC044641-009
Replace if damaged.
CAUTION
xx1300002396
xx1300002608
xx1400000485
Action Note
8 Screw the screws, little by little, to press
the sealing into place.
xx1400000486
xx1300002610
Action Note
3 Refit the tubular cable housing with the screws. Tightening torque: 1.5 Nm.
Tubular cable housing:
3HAC059695-001
Tubular cable housing, Clean
Room
Tubular cable housing, food grade
lubrication
: 3HAC056143-001
Tubular cable housing, Hygienic:
3HAC079692-001
xx1300002392
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the timing belt on the pulley.
xx1300002351
Action Note
4 Secure the motor with its attachment
screws.
xx1300002350
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Refit the connector plate and secure with Tightening torque: 0.3 Nm.
the M3 screws.
xx1400001401
xx1400001402
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 Connect the axis-5 FPC connectors and
snap them to their holders.
xx1300002390
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.
2 For robots with protection class IP67 Gasket for tubular cover: 3HAC058822-001
For robots with protection type Foundry (not Hygienic robots) / 3HAC080709-001
Plus (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cover gasket.
Replace if damaged.
xx1400000034
Action Note
3 For robots with protection class IP67 Gasket for tubular cable housing cover:
For robots with protection type Foundry 3HAC056707-001 (not Hygienic robots) /
Plus 3HAC080701-001 (Hygienic robots)
For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Check the tubular cable housing cover
gasket.
Replace if damaged.
xx1400000345
Action Note
4 Refit the both covers to the wrist. Screws: 3HAB3409-207 (M3x8).
Tightening torque: 1.5 Nm.
For robots with protection class IP67 For robots with protection class IP67
For robots with protection type Foundry For robots with protection type Foundry
Plus Plus
Apply locking liquid Loctite 243 to the two
front screws on the left hand side cover,
encircled in the figure.
Remember to refit the extra two screws and
washers to the tubular cover.
xx1300002349
For robots with protection type Clean For robots with protection type Clean
Room Room
For robots with food grade lubrication For robots with food grade lubrication
Remember to refit the extra two screws and
washers to the tubular cover.
xx1600001153
Note
xx2100001406
Concluding procedure
Action Note
1 For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic
Clean, seal and paint the joints that have
been opened. See Cut the paint or surface
on the robot before replacing parts on
page 158.
Note
5 Calibration
5.1 Introduction to calibration
Calibration information
This chapter includes general information about the recommended calibration
methods and also the detailed procedures for updating the revolution counters,
checking the calibration position etc.
Detailed instructions of how to perform Axis Calibration are given on the
FlexPendant during the calibration procedure. To prepare calibration with Axis
Calibration method, see Calibrating with Axis Calibration method on page 818.
Calibration terminology
Term Definition
Calibration method A collective term for several methods that might be
available for calibrating the ABB robot. Each method
contains calibration routines.
Synchronization position Known position of the complete robot where the
angle of each axis can be checked against visual
synchronization marks.
Calibration position Known position of the complete robot that is used
for calibration of the robot.
Standard calibration A generic term for all calibration methods that aim
to move the robot to calibration position.
Fine calibration A calibration routine that generates a new zero posi-
tion of the robot.
Reference calibration A calibration routine that in the first step generates
a reference to current zero position of the robot. The
same calibration routine can later on be used to re-
calibrate the robot back to the same position as when
the reference was stored.
This routine is more flexible compared to fine calib-
ration and is used when tools and process equipment
are installed.
Requires that a reference is created before being
used for recalibrating the robot.
Requires that the robot is dressed with the same
tools and process equipment during calibration as
during creation of the reference values.
Update revolution counter A calibration routine to make a rough calibration of
each manipulator axis.
Synchronization mark Visual marks on the robot axes. When marks are
aligned, the robot is in synchronization position.
Overview
This section specifies the different types of calibration and the calibration methods
that are supplied by ABB.
Types of calibration
xx0400001197
If a service operation is done to a robot with the option Absolute Accuracy, a new
absolute accuracy calibration is required in order to establish full performance.
For most cases after replacements that do not include taking apart the robot
structure, standard calibration is sufficient.
The Absolute Accuracy option varies according to the robot mounting position.
This is printed on the robot name plate for each robot. The robot must be in the
correct mounting position when it is recalibrated for absolute accuracy.
References
Article numbers for the calibration tools are listed in the section Special tools on
page 891.
When to calibrate
The system must be calibrated if any of the following situations occur.
Introduction
This section shows the position of the synchronization marks and the
synchronization position for each axis.
xx1400000402
xx2100001464
Overview
When calibrating, the axis must consistently be run towards the calibration position
in the same direction in order to avoid position errors caused by backlash in gears
and so on. Positive directions are shown in the graphic below.
Calibration service routines will handle the calibration movements automatically
and these might be different from the positive directions shown below.
(C)
(D)
(E)
(F)
(B)
(A)
xx1300000365
Introduction
This section describes how to do a rough calibration of each manipulator axis by
updating the revolution counter for each axis, using the FlexPendant.
xx1500000942
Action
2 All mechanical units connected to the system are shown with their calibration status.
Tap the mechanical unit in question.
xx1500000943
xx1500000944
Action
4 A screen is displayed, tap Rev. Counters.
en0400000771
Introduction
This section describes how to do a rough calibration of each manipulator axis by
updating the revolution counter for each axis, using the FlexPendant.
Note
This step is required only if you are not already in the Mechanical Unit page when
you open Calibrate.
Note
The Mechanical Unit page is displayed only if there are more than one mechanical
unit available. Otherwise, the calibration summary page for the available mechanical
unit is displayed.
3 Select the mechanical unit for which revolution counter need to be updated.
4 The calibration summary page for the selected mechanical unit is displayed.
Calibration method used at factory for each axis is shown, as well as calibration
method used during last field calibration.
5 Tap Calibration Methods on the right pane.
The calibration options are displayed.
6 Tap Revolution Counters.
7 In the Selection column select the axes for which revolution counters need to be up-
dated.
8 Tap Update.
A dialog box is displayed, warning that the updating operation cannot be undone:
• Tap Update to proceed with updating the revolution counters.
• Tap Cancel to cancel updating the revolution counters.
Tapping Update and a confirmation window is displayed.
Action
9 Tap OK.
The revolution counter for the selected axes is updated.
10
CAUTION
WARNING
Calibrating the robot with Axis Calibration requires special calibration tools
from ABB. Using other pins in the calibration bushings may cause severe
damage to the robot and/or personnel.
WARNING
The calibration tool must be fully inserted into the calibration bushing, until
the steel spring ring snaps into place.
2 During the calibration procedure, RobotWare moves the robot axis chosen
for calibration so that the calibration tools get into contact. RobotWare records
values of the axis position and repeats the coming-in-contact procedure
several times to get an exact value of the axis position.
WARNING
Risk of pinching! The contact force for large robots can be up to 150 kg.
Keep a safe distance to the robot.
3 The axis position is stored in RobotWare with an active choice from the
operator.
Note
When calibrating the robot with the reference calibration routine, the robot must
be dressed with the same tools, process cabling and any other equipment as
when the reference values were created.
If calibrating the robot with reference calibration there must be reference values
created before repair is made to the robot, if values are not already available.
Creating new values requires possibility to move the robot. The reference values
contain positions of all axes, torque of axes and technical data about the tool
installed. A benefit with reference calibration is that the current state of the robot
is stored and not the state when the robot left the ABB factory. The reference value
will be named according to tool name, date etc.
Follow the instructions given in the reference calibration routine on the FlexPendant
to create reference values.
When reference calibration is performed, the robot is restored to the status given
by the reference values.
Validation
In the mentioned routines, it is also possible to validate the calibration data.
These axes are marked with Unrestricted in the FlexPendant window. Also the
following table shows the dependencies between the axes.
Axis to calibrate
Required Axis 1 Axis 2 Axis 3 Axis 4 Axis 5 Axis 6
position of
axis
Axis 1 - * * * * *
Axis 2 0 - 0 * * *
Axis 3 0 0 - * * *
Axis 4 * * * - * *
Axis 5 * * * * - X
Axis 6 * * * * * -
- Axis to be calibrated
* Unrestricted. Axis is allowed to be jogged to other position than 0 degrees.
0 Axis must be put in position 0 degrees.
X Special requirement
WARNING
Calibrating the robot with Axis Calibration requires special calibration tools from
ABB. Using other pins in the calibration bushings may cause severe damage to
the robot and/or personnel.
WARNING
xx1500001914
A Tube insert
B Plastic protection
C Steel spring ring
xx1500000951
A Outer diameter
Periodic check of the calibration tool for the tool flange (3HAC058238-001)
If including the tool flange calibration tool in a local periodic check system, the
following measures should be checked.
• Outer diameter within Ø5g5 mm.
• Straightness within 0.005 mm.
xx1600001142
A Outer diameter
xx1600001035
xx1600001036
Spare parts
When calibration is not being performed, a protective plug should always be
installed in the bushing. Replace damaged parts with new, if needed.
Spare part Article number Note
Protective plug for bushing 3HAC059556-001 Replace if damaged or missing.
Protective plug for bushing, Clean 3HAC059557-001 Used with protection type Clean
Room Room
Protective plug for bushing, food Used for robots with food grade
grade lubrication lubrication
Protective plug for bushing, Hygien- Used with protection type Hygien-
ic ic
Replace if damaged or missing.
Required tools
The calibration tools used for Axis Calibration are designed to meet requirements
for calibration performance, durability and safety in case of accidental damage.
WARNING
Calibrating the robot with Axis Calibration requires special calibration tools from
ABB. Using other pins in the calibration holes may cause severe damage to the
robot and/or personnel.
Required consumables
Consumable Article number Note
Clean cloth -
Spare parts
After the calibration method has been started on the FlexPendant, the following
sequence will be run.
1 Choose calibration routine. The routines are described in Routines in the
calibration procedure on page 819.
2 Choose which axis/axes to calibrate.
3 The robot moves to synchronization position.
4 Validate the synchronization marks.
5 The robot moves to preparation position.
6 Remove the protection plug from the bushings, and install the calibration
tool.
7 The robot performs a measurement sequence by rotating the axis back and
forth.
8 Remove the calibration tool and reinstall the protection plugs in the bushings.
9 The robot moves to verify that the calibration tool is removed.
10 Choose whether to save the calibration data or not.
Calibration of the robot is not finished until the calibration data is saved, as last
step of the calibration procedure.
Note
3 Check if the standard calibration data for axes 4 If the data is optimized, the calibra-
or 5 are updated with wrist optimization. tion routine Wrist Optimization
This is shown in the calibration overview/summary must be re-run after standard calib-
window on the FlexPendant. ration.
See Calibrating with Wrist Optimiza-
tion method on page 834.
Action Note
2 All mechanical units connected to the system are
shown with their calibration status.
Tap the mechanical unit in question.
Note
3 The calibration method used at ABB factory for The FlexPendant will give all inform-
each axis is shown, as well as calibration method ation needed to proceed with Axis
used for the robot during last field calibration. Calibration.
4 Valid for RobotWare 6
Tap Call Calibration Method. The software will
automatically call for the procedure for the valid
calibration method. If not, tap Call Routine and
then tap Axis calibration.
5 Valid for RobotWare 7
Tap Calibration Methods on the right pane and
then tap Calibration. The software will automatic-
ally call for the procedure for the valid calibration
method.
6 Follow the instructions given on the FlexPendant. A brief overview of the sequence
that will be run on the FlexPendant
is given in Overview of the calibra-
tion procedure on the FlexPendant
on page 826.
allowed to be jogged will be given on the FlexPendant. These axes are marked
with Unrestricted in the FlexPendant window.
Calibration tools in contact
Axis 1 Axis 2
xx1600001277 xx1600001276
Axis 3 Axis 4
xx1600001275 xx1600001274
Axis 5 Axis 6
Make sure to orient the tool flange calibration
tool correctly.
xx1600001273
xx1600001272
CAUTION
After calibration
Action Note
1 Check the o-ring on the plug.
Replace the plug with new spare part, if missing
or damaged.
Note
Action Note
2 Reinstall the protective plugs in both bushings on
each axis, directly after the axis is calibrated.
Replace the plug with new spare part, if missing
or damaged.
Note
Tip
Select positions with large reorientations around the TCP. For best results,
make sure that axis 4 and 5 have large movements.
a Jog the robot to an appropriate position,
A, for the first approach point.
Use small increments to accurately posi-
tion the tool tip as close to the reference
point as possible.
b Tap Modify Position to define the point.
c Repeat for each approach point to be
defined, positions B, C, and D.
Jog away from the fixed world point to
achieve the best result. Just changing the
tool orientation will not give as good a
result.
en0400000906
5 The robot moves to the optimized positions for the wrist axes and
automatically overwrites previous calibration data.
WARNING
Calibration position
The position of the axis to be calibrated is illustrated in each calibration section
respectively.
The table below specifies the exact axis positions in degrees.
Axis IRB 1200-5/0.9 IRB 1200-7/0.7
1 +84.474066º +84.474066º
2 +131.862755º +136.862755º
3 +72.250000º +72.250000º
4 0º 0º
5 -90º -90º
6 0º 0º
xx1400001209
Required equipment
Equipment Art. no. Note
Calibration toolkit, manual calibra- 3HAC051256-001 Includes calibration tools, pins
tion and attachment screws for
manual calibration method. i
Required consumables
Equipment Art. no. Note
Cleaning agent - Isopropanol
Calibrating axis 1
Moving the robot to calibration position
Action Note
1 Jog all axes to zero position.
2 Remove the axis-1 mechanical stop pin.
xx1400000392
Action Note
3 The axis-1 calibration stop pin should now be fit- Screw: M8x45.
ted to the mechanical stop pin attachment hole, Tightening torque: 10 Nm.
but it does not fit if the axis 1 stands in its zero
position.
Note
Jog axis 1 to find a suitable position where the
axis-1 calibration stop pin can be fitted to the at- The position of the robot shown in
tachment hole in the base. the figure, is only a suggestion.
Fit the axis-1 calibration stop pin to the base and The suitable position in which the
secure it with the screw. axis-1 calibration pin is possible to
fit may differ.
xx1400001100
xx1400001134
Action Note
7 Fit the axis-1 calibration pin to the swing and se- Screw: M5x40.
cure it with the screw. TighteningTorque: 5 Nm.
CAUTION
xx1400001099
10 Release the brakes and manually rotate axis 1 How to release the brakes is de-
until the two axis-1 calibration pins touches each tailed in Manually releasing the
other gently. There should be no pressing force brakes on page 71.
between the pins.
When doing this, pay attention to robot pose in
order to avoid arm collision.
When the axis is in position, release the brake
release button to activate the brakes again.
xx1400001209
en0400001127
Action Note
6 Tap Calibrate.
A dialog box is displayed, warning that calibration
of the selected axes will be changed, which cannot
be undone:
• Tap Calibrate to proceed.
• Tap Cancel to cancel.
Tapping Calibrate results in briefly displaying a
dialog box, announcing that the calibration pro-
cess has started.
The axis is calibrated and the system returns to
the list of available mechanical units.
xx1400001092
4 Remove the axis-1 calibration pin from the swing Protection plug: 3HAC051199-001
and refit the protection plug.
xx1400001134
xx1400000392
After calibration
Action Note
1 Write down the new system parameters on a new
label and stick on top of the calibration label on
the robot.
xx1400001201
Required equipment
Calibration of axis 2 is done by moving the lower arm so that the calibration pin
and calibration stop touches each other gently.
These parts are already fitted to the robot, no extra installation of calibration
equipment is required.
See figures below for reference, and follow the step-by-step procedure that follows.
Calibration pin Calibration stop
xx1400001136
xx1400001135
The press fit mechanical stop pin fitted to the The axis-2 mechanical stop fitted to the
lower arm is used for calibration of axis 2. swing is used for calibration of axis 2.
No additional equipment is required. No additional equipment is required.
Calibrating axis 2
Moving the robot to calibration position
Action Note
1 Jog all axes to zero position.
2
DANGER
3 Release the brakes and manually rotate axis 2 How to release the brakes is de-
until the axis-2 calibration pin and calibration stop tailed in Manually releasing the
touches each other gently. There should be no brakes on page 71.
pressing force between the pins. The calibration pin and calibration
When doing this, pay attention to robot pose in stop are illustrated in Required
order to avoid arm collision. equipment on page 845.
When the axis is in position, release the brake
release button to activate the brakes again.
xx1400001201
Action Note
3 Tap to select the mechanical unit and then tap Calib. Parameters.
en0400001127
Action Note
2 Jog axis 2 to zero degree using the FlexPendant.
3 Check that the synchronization marks on axis 2
are aligned with eachother.
Are they aligned within the tolerances?
• If yes, the calibration is verified OK.
• If no, redo the fine calibration procedure.
xx1400001093
After calibration
Action Note
1 Write down the new system parameters on a new
label and stick on top of the calibration label on
the robot.
xx1400001204
Required equipment
Calibration of axis 3 is done by moving the upper arm so that the calibration pin
and calibration stop touches each other gently.
These parts are already fitted to the robot, no extra installation of calibration
equipment is required.
See figures below for reference, and follow the step-by-step procedure that follows
the figures.
Calibration pin Calibration stop
xx1400001202 xx1400001203
The press fit mechanical stop pin fitted to the The axis-3 mechanical stop fitted to the lower
upper arm is used for calibration of axis 3. arm is used for calibration of axis 3.
No additional equipment is required. No additional equipment is required.
Calibrating axis 3
Moving the robot to calibration position
Action Note
1 Jog all axes to zero position.
2
DANGER
Action Note
3 Release the brakes and manually rotate axis 3 How to release the brakes is de-
until the axis-3 calibration calibration pin and cal- tailed in Manually releasing the
ibration stop touches each other gently. There brakes on page 71.
should be no pressing force between the pins. The calibration pin and calibration
When doing this, pay attention to robot pose in stop are illustrated in Required
order to avoid arm collision. equipment on page 849.
When the axis is in position, release the brake
release button to activate the brakes again.
xx1400001204
Action Note
3 Tap to select the mechanical unit and then tap Calib. Parameters.
en0400001127
Action Note
2 Jog axis 3 to zero degree using the FlexPendant.
3 Check that the synchronization marks on axis 3
are aligned with eachother.
Are they aligned within the tolerances?
• If yes, the calibration is verified OK.
• If no, redo the fine calibration procedure.
xx1400001094
After calibration
Action Note
1 Write down the new system parameters on a new
label and stick on top of the calibration label on
the robot.
xx1400001207
Required equipment
Equipment Art. no. Note
Calibration toolkit, manual calibra- 3HAC051256-001 Includes calibration tools, pins
tion and attachment screws for
manual calibration method. i
i The robot is calibrated by either manual calibration or Axis Calibration at factory. Always use the
same calibration method as used at the factory.
Information about valid calibration method is found on the calibration label or in the calibration
menu on the FlexPendant.
If no data is found related to standard calibration, manual calibration is used as default.
Required consumables
Equipment Art. no. Note
Cleaning agent - Isopropanol
Calibrating axis 4
Moving the robot to calibration position
Action Note
1 Jog all axes to zero position.
Rotate axis 4 some degrees toward positive direc-
tion to avoid interference between the calibration
tools when fitting them.
Action Note
2
DANGER
xx1400001205
xx1400001208
Tip
Action Note
7 Fit the conical screw to the calibration tool. Conical screw M3 (3HAC055410-
001, 1 pcs)
Tightening torque: 1 Nm
xx1500001608
xx1400001117
11 Release the brakes and manually rotate axis 4 How to release the brakes is de-
until the axis-4 calibration tool and the calibration tailed in Manually releasing the
block touches each other gently. There should be brakes on page 71.
no pressing force between the pins.
When doing this, pay attention to robot pose in
order to avoid arm collision.
When the axis is in position, release the brake
release button to activate the brakes again.
xx1400001207
en0400001127
Action Note
6 Tap Calibrate.
A dialog box is displayed, warning that calibration
of the selected axes will be changed, which cannot
be undone:
• Tap Calibrate to proceed.
• Tap Cancel to cancel.
Tapping Calibrate results in briefly displaying a
dialog box, announcing that the calibration pro-
cess has started.
The axis is calibrated and the system returns to
the list of available mechanical units.
xx1400001095
xx1400001205
After calibration
Action Note
1 Write down the new system parameters on a new
label and stick on top of the calibration label on
the robot.
xx1400001206
Required equipment
Equipment Art. no. Note
Calibration toolkit, manual calibra- 3HAC051256-001 Includes calibration tools, pins
tion and attachment screws for
manual calibration method. i
i The robot is calibrated by either manual calibration or Axis Calibration at factory. Always use the
same calibration method as used at the factory.
Information about valid calibration method is found on the calibration label or in the calibration
menu on the FlexPendant.
If no data is found related to standard calibration, manual calibration is used as default.
Required consumables
Equipment Art. no. Note
Cleaning agent - Isopropanol
Action Note
3 Fit the calibration block to the tubular. Screws: M4x16.
xx1400001114
4 Fit the guide pin to the disk and then fit the calib- Screws: M5x16.
ration tool of axes 5 and 6.
xx1400001115
5
DANGER
6 Release the brakes and manually rotate axes 5 How to release the brakes is de-
and 6 until the axis-5/6 calibration tool and the tailed in Manually releasing the
calibration block touches each other gently. There brakes on page 71.
should be no pressing force between the pins.
When doing this, pay attention to robot pose in
order to avoid arm collision.
When the axis is in position, release the brake
release button to activate the brakes again.
xx1400001206
en0400001127
Action Note
6 Tap Calibrate.
A dialog box is displayed, warning that calibration
of the selected axes will be changed, which cannot
be undone:
• Tap Calibrate to proceed.
• Tap Cancel to cancel.
Tapping Calibrate results in briefly displaying a
dialog box, announcing that the calibration pro-
cess has started.
The axis is calibrated and the system returns to
the list of available mechanical units.
xx1400001096
xx1400001097
After calibration
Action Note
1 Write down the new system parameters on a new
label and stick on top of the calibration label on
the robot.
Introduction
Always verify the results after calibrating any robot axis to verify that all calibration
positions are correct.
Introduction
Check the synchronization position of the robot before beginning any programming
of the robot system. This may be done:
• Using a MoveAbsJ instruction with argument zero on all axes.
• Using the Jogging window on the FlexPendant.Using the Jog window on
the FlexPendant.
6 Decommissioning
6.1 Introduction
Introduction
This section contains information to consider when taking a product, robot or
controller, out of operation.
It deals with how to handle potentially dangerous components and potentially
hazardous materials.
General
All used grease/oils and dead batteries must be disposed of in accordance with
the current legislation of the country in which the robot and the control unit are
installed.
If the robot or the control unit is partially or completely disposed of, the various
parts must be grouped together according to their nature (which is all iron together
and all plastic together), and disposed of accordingly. These parts must also be
disposed of in accordance with the current legislation of the country in which the
robot and control unit are installed.
Introduction
ABB robots contain components in different materials. During decommissioning,
all materials should be dismantled, recycled, or reused responsibly, according to
the relevant laws and industrial standards. Robots or parts that can be reused or
upcycled helps to reduce the usage of natural resources.
Symbol
The following symbol indicates that the product must not be disposed of as common
garbage. Handle each product according to local regulations for the respective
content (see table below).
xx1800000058
Hazardous material
The table specifies some of the materials in the product and their respective use
throughout the product.
Dispose components properly according to local regulations to prevent health or
environmental hazards.
Material Example application
DANGER
7 Robot description
7.1 Introduction
Manipulator description
IRB 1200 is one of ABB 6-axis industrial robots, with multiple variants designed to
work in various environments. Different IRB 1200 variant supports to work with
either IRC5/IRC5C controller or OmniCore controller, or both. The following table
lists the supported controller type for IRB 1200 in different protection classes/types.
Protection Controller type
IRC5 IRC5C OmniCore C OmniCore E
line line
Standard, IP40 X X X X
Standard, IP67 X X X X
Clean Room X X X X
Food grade lubrication X X
Foundry plus X X X X
Hygienic X X
Note
IRB 1200 Type B is designed based on IRB 1200 Type A so that Type B has the
bushings for installation of calibration tools too.
The difference between IRB 1200 Type A and IRB 1200 Type B is that Type B
also supports SafeMove 2. See Type B of IRB 1200 on page 873.
Note
If no type label attached on the robot, use the bushings on each axis to identify
a robot calibrated with Axis Calibration.
Those robots which are not equipped for Axis Calibration are simply named IRB
1200 (no type specified).
Type B - SafeMove 2
Note
IRB 1200 working with OmniCore E10 does not support SafeMove 2.
The difference between IRB 1200 Type B and other IRB 1200 versions is that the
Type B supports SafeMove 2.
As a result of this, the following parts differ from other versions:
• Base
• Drive unit, axis 2, axis 3, axis 5 and axis 6
• Motor with pulley, axis 4 and axis 5
• Manipulator cable harness
• Battery pack
• SMB unit (replacing EIB unit)
IRB 1200 Type B is designed based on IRB 1200 Type A so that Type B has the
bushings for installation of calibration tools too.
Note
IRB 1200 has different base versions that are not compatible with each other.
Always use the following list as a reference to check the base installed on robot
and order the correct spare parts.
Base installed on ro- Article number in What to order How to see which version is installed
bot (spare part num- WebConfig on robot
ber)
3HAC049628-001 3HAC044533-001 Order: Look on the outside of the base.
• base 3HAC059553-001 Base 3HAC049628-001 has no hole on
• swing 3HAC059554-001 the side of the base.
• IP40: sealing ring
3HAC068107-001
• IP67: sealing ring + gasket
+ V-ring 3HAC059791-001
xx1600000124
xx1600000051
Base installed on ro- Article number in What to order How to see which version is installed
bot (spare part num- WebConfig on robot
ber)
3HAC059553-001 3HAC058386-001 Order: Base 3HAC059553-001 has a bushing
• base 3HAC059553-001 for fitting calibration tool for Axis Calib-
ration.
xx1600001037
Note
IRB 1200 has different swing versions that are not compatible with each other.
Always use the following list as a reference to check the swing installed on robot
and order the correct spare parts.
Swing installed on ro- Article number in What to order How to see which version is in-
bot (spare part num- WebConfig stalled on robot
ber)
3HAC049632-001 3HAC044534-001 Order: Look underneath the swing, the sur-
• swing 3HAC059554-001 face is flat.
• IP67: sealing ring +
gasket + V-ring
3HAC059791-001
xx1600000052
xx1600000053
Swing installed on ro- Article number in What to order How to see which version is in-
bot (spare part num- WebConfig stalled on robot
ber)
3HAC059554-001 3HAC058387-001 Order: The swing has a bushing for fitting
• swing 3HAC059554-001 calibration tool for Axis Calibration.
xx1600001038
7.4.3 Spare part versions for the axis-1 sealing ring on IP40/IP67 robots
Spare part versions for the axis-1 sealing ring on IP40/IP67 robots
Note
IRB 1200 has different axis-1 sealing ring versions that are not compatible with
each other. Always use the following list as a reference to check the sealing ring
installed on robot and order the correct spare parts.
Sealing ring installed Article number in What to order How to see which version is in-
on robot (spare part WebConfig stalled on robot
number)
3HAC044676-001 3HAC044676-001 Order: The sealing ring is flat.
• sealing ring 3HAC044676-
001
xx1600000125
xx1600000126
xx1600001039
xx1900001603
Compatibility between cable harness and axis-1 sealing ring on IP40/IP67 robots
The manipulator cable harness is designed with different cable brackets that are
compatible with different spare part versions of the axis-1 sealing ring. Always use
the following list as a reference to check the cable harness installed on robot and
order the correct spare parts.
How to see which kind of cable harness is What to order
installed on robot
Order:
• corresponding cable harness.
See "Manipulator cable harness" in
Product manual, spare parts - IRB
1200 for spare part numbers.
• sealing ring 3HAC068107-001
xx1900001602
Order:
• corresponding cable harness.
See "Manipulator cable harness" in
Product manual, spare parts - IRB
1200 for spare part numbers.
xx1900001601
Note
IRB 1200 and IRB 1200 Type A have different housing versions that are not
compatible with each other. Always use the following list as a reference to check
the housing installed on robot and to order the correct spare parts.
Robot Housing installed on Article number in What to order How to see which version
variant robot (spare part WebConfig is installed on robot
number)
IRB 1200- 3HAC059680-001 3HAC044544-001 Order: The plane (encircled in the
7/0.7 • housing (IRB 1200-7/0.7 figure) on housing
): 3HAC059680-001 3HAC059680-001 has no
painting, while that on
3HAC059721-001 3HAC058389-001 Order: housing 3HAC059721-001
• housing (IRB 1200-7/0.7 is painted.
): 3HAC059721-001
xx1600001127
xx1600001129
Note
IRB 1200 and IRB 1200 Type A have different tubular versions that are not
compatible with each other. Always use the following list as a reference to check
the tubular installed on robot and to order the correct spare parts.
Tubular installed on robot Article number in What to order How to see which version is
(spare part number) WebConfig installed on robot
3HAC059693-001 3HAC044548-001 Order: The plane (encircled in the fig-
• tubular with sleeve: ure) on tubular 3HAC059693-
3HAC059693-001 001 has no painting, while that
on tubular 3HAC059723-001 is
3HAC059723-001 3HAC058390-001 Order: painted.
• tubular with sleeve:
3HAC059723-001
xx1600001128
7.4.6 Spare part versions for the tubular cover on Clean Room robots
Spare part versions for the tubular cover on Clean Room robots
Note
IRB 1200 with protection type Clean Room has different tubular cover versions
that are not compatible with each other. Always use the following list as a
reference to check the tubular cover installed on robot and to order the correct
spare parts.
Tubular cover installed on Article number in What to order How to see which version is in-
Clean Room robots (spare WebConfig stalled on robot
part number)
3HAC056144-001 3HAC044550-001 Order: Tubular cover 3HAC056144-001
• tubular cover, clean has six screw holes.
room: 3HAC056144-
001
xx1600001117
xx1600001118
8 Reference information
8.1 Introduction
General
This chapter includes general information, complementing the more specific
information in the different procedures in the manual.
General
The product is compliant with ISO 10218-1:2011, Robots for industrial environments
- Safety requirements - Part 1 Robots, and applicable parts in the normative
references, as referred to from ISO 10218-1:2011. In case of deviation from ISO
10218-1:2011, these are listed in the declaration of incorporation. The declaration
of incorporation is part of the delivery.
Robot standards
Standard Description
ISO 9283 Manipulating industrial robots – Performance criteria and re-
lated test methods
ISO 9787 Robots and robotic devices – Coordinate systems and motion
nomenclatures
ISO 9946 Manipulating industrial robots – Presentation of characteristics
Standard Description
IEC 60204 Safety of machinery - Electrical equipment of machines - Part
1: General requirements, normative reference from ISO 10218-
1
IEC 61000-6-2 Electromagnetic compatibility (EMC) – Part 6-2: Generic
standards – Immunity standard for industrial environments
IEC 61000-6-4 Electromagnetic compatibility (EMC) – Part 6-4: Generic
standards – Emission standard for industrial environments
ISO 13849-1:2006 Safety of machinery - Safety related parts of control systems
- Part 1: General principles for design, normative reference
from ISO 10218-1
Standard Description
ANSI/RIA R15.06 Safety requirements for industrial robots and robot systems
ANSI/UL 1740 Safety standard for robots and robotic equipment
CAN/CSA Z 434-03 Industrial robots and robot Systems - General safety require-
ments
Converter table
Use the following table to convert units used in this manual.
Quantity Units
Length 1m 3.28 ft. 39.37 in
Weight 1 kg 2.21 lb.
Weight 1g 0.035 ounces
Pressure 1 bar 100 kPa 14.5 psi
Force 1N 0.225 lbf
Moment 1 Nm 0.738 lbf-ft
Volume 1L 0.264 US gal
General
This section describes how to tighten the various types of screw joints on ABB
robots.
The instructions and torque values are valid for screw joints comprised of metallic
materials and do not apply to soft or brittle materials.
UNBRAKO screws
UNBRAKO is a special type of screw recommended by ABB for certain screw joints.
It features special surface treatment (Gleitmo as described below) and is extremely
resistant to fatigue.
Whenever used, this is specified in the instructions, and in such cases, no other
type of replacement screw is allowed. Using other types of screws will void any
warranty and may potentially cause serious damage or injury.
Tightening torque
Before tightening any screw, note the following:
• Determine whether a standard tightening torque or special torque is to be
applied. The standard torques are specified in the following tables. Any
special torques are specified in the repair, maintenance or installation
procedure descriptions. Any special torque specified overrides the standard
torque!
• Use the correct tightening torque for each type of screw joint.
• Only use correctly calibrated torque keys.
• Always tighten the joint by hand, and never use pneumatic tools.
• Use the correct tightening technique, that is do not jerk. Tighten the screw
in a slow, flowing motion.
• Maximum allowed total deviation from the specified value is 10%!
Note
Note
Dimension Tightening torque (Nm) Tightening torque (Nm) Tightening torque (Nm)
Class 8.8, oil-lubricated Class 10.9, oil-lubric- Class 12.9, oil-lubric-
ated ated
M5 6 - -
M6 10 - -
M8 24 34 40
M10 47 67 80
M12 82 115 140
M16 200 290 340
M20 400 560 670
M24 680 960 1150
Note
Definition
In installation, repair, and maintenance procedures, weights of the components
handled are sometimes specified. All components exceeding 22 kg (50 lbs) are
highlighted in this way.
To avoid injury, ABB recommends the use of a lifting accessory when handling
components with a weight exceeding 22 kg. A wide range of lifting accessories
and devices are available for each manipulator model.
Example
Following is an example of a weight specification in a procedure:
Action Note
CAUTION
General
All service (repairs, maintenance, and installation) procedures contains lists of
tools required to perform the specified activity.
All special tools required are listed directly in the procedures while all the tools
that are considered standard are gathered in the standard toolkit and defined in
the following table.
This way, the tools required are the sum of the standard toolkit and any tools listed
in the instruction.
General
All service instructions contain lists of tools required to perform the specified
activity. The required tools are a sum of standard tools, defined in the section
Standard toolkit on page 890, and of special tools, listed directly in the instructions
and also gathered in this section.
Special tools
EIB/SMB unit
sealing ring
Signal lamp
Lower arm
and pulley
Tools and equipment with spare part number:
(These tools can be ordered from ABB)
Guide pins
3HAC049703-001 Guide pin for axis-1 gear unit 3 3 3
3HAC049704-001 Guide pin for axis-2 gear unit 3 3
3HAC049705-001 Guide pin for upper arm 3
3HAC049706-001 Guide pin for tilt unit (axis 5) 3 3
xx2100001461
Lifting accessories
xx1400000542
Roundsling, 2 m
- Length: 2 m. Lifting capacity: 100 1 1 1
kg.
xx1400000535
EIB/SMB unit
sealing ring
Signal lamp
Lower arm
and pulley
Tools and equipment with spare part number:
(These tools can be ordered from ABB)
xx1400000541
xx1400000538
xx1400000539
xx1400000540
Other tools
- 24 VDC power supply 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Calibration toolkit, manual
3HAC051256-001 1 1 1 1 1 1 1 1 1 1 1 1 1
calibration
3HAC079686-001
3HAC074119-001
Calibration
xx2100001462
1
Cable harness
EIB/SMB unit
1
(including sealings)
1
Lower arm
Signal lamp
and pulley
1
General
Many repair and maintenance activities require different pieces of lifting accessories,
which are specified in each procedure.
The use of each piece of lifting accessories is not detailed in the activity procedure,
but in the instruction delivered with each piece of lifting accessories.
The instructions delivered with the lifting accessories should be stored for later
reference.
9 Spare parts
9.1 Spare part lists and illustrations
Location
Spare parts and exploded views are not included in the manual but delivered as
a separate document for registered users on myABB Business Portal,
www.abb.com/myABB.
Tip
10 Circuit diagrams
10.1 Circuit diagrams
Overview
The circuit diagrams are not included in this manual, but are available for registered
users on myABB Business Portal, www.abb.com/myABB.
See the article numbers in the tables below.
Controllers
Manipulators
Index brakes
testing function, 38
A C
Absolute Accuracy, calibration, 807 cabinet lock, 31
allergenic material, 30 cable package main
aluminum replacing, 169
disposal, 868 cabling, robot, 106
ambient humidity cabling between robot and controller, 106
operation, 53 calibrating
storage, 53 robot, 818
ambient temperature roughly, 813, 816
operation, 53 calibrating robot, 818, 834
storage, 53 calibration
assembly instructions, 41 Absolute Accuracy type, 806
assessment of hazards and risks, 30 rough, 813, 816
axis-5 and axis-6 drive unit standard type, 806
replacing, 778 verification, 864
axis-5 FPC unit when to calibrate, 809
replacing, 277 calibration, Absolute Accuracy, 807
axis-5 motor calibration manuals, 808
replacing, 758 calibration marks, 810
axis-5 timing belt calibration position
replacing, 771 jogging to, 865–866
axis-4 FPC unit scales, 810
replacing, 245 calibration scales, 810
axis-4 gear unit CalibWare, 806
replacing, 686 carbon dioxide extinguisher, 31
axis-4 motor cast iron
replacing, 728 disposal, 868
axis-4 pulley cleaning, 149
replacing, 686 Hygienic robots, 152
axis-4 shaft climbing on robot, 34
replacing, 686 Cold environments, 114
axis-4 timing belt connecting the robot and controller, cabling, 106
replacing, 740 copper
axis-3 disposal, 868
radial sealing
replacing, 418 D
sealing ring damage to mechanical stop, 126
replacing, 418 detergents, 153
axis-3 drive unit dimensions
replacing, 664 robot, 84
axis-3 gearbox direction of axes, 812
replacing, 664 drive unit
axis-3 motor axis-3, 664
replacing, 664 axis-2, 642
axis-2 drive unit
replacing, 642 E
Axis Calibration, 818 EIB/SMB battery
calibration tool extension of lifetime, 134
article number, 821, 826 replacing, 134
examining, 821 EIB unit
installation position, 824 replacing, 291
overview of method, 818 environmental information, 868
procedure on FlexPendant, 826, 834 equipment, robot, 84
protective cover and protection plug, 824, 826 equipment on robot, fitting, 85
ESD
B damage elimination, 64
base sensitive equipment, 64
replacing, 492 extra equipment, 84
batteries
disposal, 868 F
battery fire extinguishing, 31
replacing, 134 fitting
battery shutdown extra equipment, 85
service routine, 134 fitting, equipment, 84
FlexPendant M
jogging to calibration position, 865–866 main power connector, o-ring, 108
MoveAbsJ instruction, 865–866 maintenance intervals, 117
updating revolution counters, 813, 816 maintenance schedule, 117
foundation mechanical stop
requirements, 52 axis-4, 460
FPC unit axis-3, 457
axis-5, 277 axis-2, 454
axis-4, 245 axis-1, 638
mechanical stop location, 126
G motor
gearbox axis-6, 778
axis-3, 664 axis-5, 758
axis-2, 642 axis-4, 728
gear unit axis-3, 664
axis-4, 686 motor unit
Gravity Alpha, 79 axis-2, 642
Gravity Beta, 78 mounting, equipment, 84
grease, 34 MoveAbsJ instruction, 865–866
disposal, 868
N
H national regulations, 30
hanging negative directions, axes, 812
installed hanging, 30 neodymium
hazard levels, 21 disposal, 868
hazardous material, 868 nodular iron
height disposal, 868
installed at a height, 30
hot surfaces, 34 O
housing extender unit oil, 34
replacing, 245 disposal, 868
sealings, 245 operating conditions, 53
HRA, 30 option
humidity signal lamp, 94, 97
operation, 53 original spare parts, 19
storage, 53 o-rings, enclosed with robot, 75, 108
o-rings, extra at delivery, 42
I
information labels location, 121 P
inspecting paint
information labels, 121 inspecting, 119
mechanical stop, 126 pedestal
paint, 119 installed on pedestal, 30
robot cabling, 120 personnel
timing belts, 129 requirements, 20
installation positive directions, axes, 812
equipment, 84 PPE, 20
instructions for assembly, 41 product standards, 884
integrator responsibility, 30 protection classes, 53
intervals for maintenance, 117 protection sleeve, base
replacing, 492
L protection type, 53
labels protective equipment, 20
robot, 23 protective wear, 20
lamp unit pulley
installing, 94, 97 axis-5, 758
lifting
accessory, 70 R
lifting accessory, 889 radial sealing
limitation of liability, 19 axis-4, replacing, 245
Lithium axis-2, replacing, 572
disposal, 868 axis-1, replacing, 492
loads on foundation, 51 recycling, 868
lock and tag, 31 regional regulations, 30
lower arm release brakes, 37
replacing, 308 replacements, report, 157
lubricants, 34 replacing
upcycling, 868 W
updating revolution counters, 813, 816 wall mounting, 78
users weight, 50
requirements, 20 robot, 69
Wrist Optimization
V overview of method, 834
validity and responsibility, 19
velocity Z
adjusting, 114 zero position
verifying calibration, 864 checking, 865
ABB AS
Robotics & Discrete Automation
Nordlysvegen 7, N-4340 BRYNE, Norway
Box 265, N-4349 BRYNE, Norway
Telephone: +47 22 87 2000
ABB Inc.
Robotics & Discrete Automation
1250 Brown Road
Auburn Hills, MI 48326
USA
Telephone: +1 248 391 9000
abb.com/robotics
3HAC046983-001, Rev S, en