Professional Documents
Culture Documents
Material Safety Data Sheet Belzona® 1311 (Ceramic R-Metal) Base
Material Safety Data Sheet Belzona® 1311 (Ceramic R-Metal) Base
11103
2 HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Dark gray. Paste. Epoxy odor. WARNING. May cause allergic skin reaction. May cause irritation to eyes or skin. Combustible liquid - Class
IIIB. Prevent the product from entering into soil, drains, sewers, ditches or waterways.
1/ 6
REVISION DATE 09/23-2011 SDS No. 11103
3 COMPOSITION/INFORMATION ON INGREDIENTS
COMPOSITION COMMENTS
The remaining constituents of this product are either considered to be non-hazardous or below the relevant concentration limits.
4 FIRST-AID MEASURES
GENERAL INFORMATION
In all cases of doubt, or when symptoms persist, seek medical attention. Never give anything by mouth to an unconscious person.
INHALATION
Remove to fresh air. Keep the patient warm and at rest. If breathing has stopped, administer artificial respiration. Give nothing by mouth.
If unconscious, place in the recovery position and seek medical advice.
INGESTION
If accidentally swallowed obtain immediate medical attention. Keep at rest. Rinse mouth with plenty of water and drink plenty of water. Do
NOT induce vomiting.
SKIN CONTACT
Remove contaminated clothing and shoes. Wash skin thoroughly with soap and water or use a proprietary skin cleaner. Do NOT use
solvents or thinners. If irritation or inflammation persists, seek medical attention.
EYE CONTACT
Contact lenses should be removed. Irrigate copiously with clean, fresh water for at least 15 minutes, holding the eyelids apart, and seek
medical advice.
5 FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA
Use: sand, alcohol resistant foam, carbon dioxide, chemical powder, water fog for larger fires.
Do NOT use water jet.
SPECIAL FIRE FIGHTING PROCEDURES
Fire will produce dense black smoke containing hazardous products of combustion (see Section 10). Exposure to decomposition products
may be a hazard to health. Appropriate positive-pressure self-contained breathing apparatus (SCBA) and full fire fighting turn-out gear
(Bunker gear) should be worn. Cool closed containers exposed to fire with water spray. Do not allow run-off from fire fighting to enter
drains, sewers, ditches or waterways.
UNUSUAL FIRE & EXPLOSION HAZARDS
SENSITIVITY TO MECHANICAL IMPACT
The product is not sensitive to mechanical impact or physical shock.
SENSITIVITY TO STATIC DISCHARGE
The product is not sensitive to static discharge.
AUTO IGNITION TEMPERATURE NIA
(°C)
FLAMMABILITY LIMIT - NIA
LOWER(%)
FLAMMABILITY LIMIT - UPPER(%) NIA
FLASH POINT (°C) CC (Closed cup). >170 (338°F)
FLAMMABILITY CLASS
3.2 Combustible Liquid IIIB
2/ 6
REVISION DATE 09/23-2011 SDS No. 11103
HANDLING
GENERAL
Vapors may collect in the container headspace during transit or prolonged storage. Avoid breathing vapor when opening the container.
Where possible open containers and mix components in a well ventilated place away from the application area. Avoid contact with eyes,
skin and clothing. Smoking, eating and drinking should be prohibited in areas of storage and use. For personal protection see Section 8.
Always keep in containers made of the same material as the supply container. Good housekeeping methods and regular safe removal of
waste materials should be observed.
FIRE/EXPLOSION
This product is combustible. Exclude sources of heat, sparks and open flame.
STORAGE
Observe the label precautions. Store between 5°C (41°F) and 30°C (86°F) unless otherwise stated in a dry, well ventilated place away
from sources of heat, ignition and direct sunlight. No smoking. Prevent unauthorized access. Store separately from oxidizing agents and
strongly alkaline and strongly acidic materials.
ENVIRONMENTAL STORAGE PRECAUTIONS
Spillage, incorrect storage of chemicals or waste materials or unsuitable disposal activities can result in pollutants seeping through the
soil, causing serious harm to groundwater- which is a vital source of drinking water. All wastes especially liquid wastes, should be securely
stored on site in designated areas that are isolated from waterways and groundwater and diked to contain any spillages.
INGREDIENT COMMENTS
No exposure limits noted for ingredient(s). Consult local authorities for acceptable exposure limits.
ENGINEERING MEASURES
Open containers in a well ventilated area.
RESPIRATORY EQUIPMENT
STANDARD APPLICATIONS
Respirators are not normally required, but may be required where adequate ventilation cannot be achieved.
EMERGENCY SITUATIONS
Where entry into unknown or Immediately Dangerous To Life or Health (IDLH) atmospheres is required, an OSHA/NIOSH approved
pressure-demand self-contained breathing apparatus (SCBA) with a full facepiece or a pressure-demand supplied-air respirator (SAR) with
a full facepiece in combination with an auxiliary pressure-demand SCBA respirator should be worn.
HAND PROTECTION
GENERAL GUIDANCE ON HAND PROTECTION
The breakthrough time of the gloves selected should exceed the expected use period. Where this is not possible gloves should be
changed in good time, and in any case before the breakthrough time is exceeded. Where doubt exists, advice should be sought from
manufacturers or vendors of protective gloves in order to determine appropriate types for the particular circumstances. Barrier creams may
help to protect exposed areas of skin but are not substitutes for full physical protection. They should not be applied once exposure has
occurred.
SPECIFIC RECOMMENDATIONS
Use protective gloves made of: Neoprene. Nitrile.
STANDARD APPLICATIONS / EMERGENCY SITUATIONS
Medium-heavy weight gauntlet type gloves that provide wrist protection are suitable.
EMERGENCY REPAIRS OR APPLICATION OF SINGLE UNITS
Light weight disposable gloves are normally suitable.
EYE PROTECTION
STANDARD APPLICATIONS
It is recommended that eye protection, for example safety glasses with side shields or goggles are worn at all times during the handling
and use of this material. During subsequent machining, grinding, abrasion or removal of this product appropriate eye protection should be
selected according to the type of tools or equipment used.
EMERGENCY SITUATIONS
Refer to 'Respiratory Equipment' above.
3/ 6
REVISION DATE 09/23-2011 SDS No. 11103
APPEARANCE Paste.
COLOR Dark gray.
ODOR Epoxy.
PHYSICAL DATA COMMENTS This section contains typical values for Health, Safety and Environmental guidance only and is not
intended to represent a technical specification for the product. LP = See Section 12. *VOC values
determined using test method ASTM D2369-10
SOLUBILITY Immiscible with water
BOILING POINT (°C) >200 (392°F) @ 760 mm Hg
MELTING POINT (°C) NIA
RELATIVE DENSITY 2.60 - 2.80 @ 20°C (68°F)
VAPOR DENSITY (air=1) >1
VAPOR PRESSURE < 0.0002 kPa @ 20°C (68°F)
EVAPORATION RATE N.ap
pH-VALUE, CONC. SOLUTION NIA
VISCOSITY N.ap
DECOMPOSITION TEMPERATURE >200 (392°F)
(°C)
ODOR THRESHOLD, LOWER NIA
FLASH POINT (°C) >170 (338°F) CC (Closed cup).
PARTITION COEFFICIENT LP
(N-Octanol/Water)
VOLATILE ORGANIC CONTENT 26* g/litre
STABILITY
Stable under recommended storage and handling conditions (see Section 7). In a fire, hazardous decomposition products such as smoke,
carbon monoxide, carbon dioxide may be produced.
CONDITIONS TO AVOID
Keep away from oxidizing agents and strongly alkaline and strongly acidic materials to prevent the possibility of exothermic reaction.
11 TOXICOLOGICAL INFORMATION
TOXICOLOGICAL INFORMATION
There is no data on the product itself.
Name REACTION PRODUCT: BISPHENOL A-(EPICHLORHYDRIN)
Toxic Dose 1 - LD 50 >11,400 mg/kg (oral rat)
Toxic Dose 2 - LD 50 >23,500 mg/kg (dermal rat)
Toxic Conc. - LC 50 N.ap
Toxicological information
4/ 6
REVISION DATE 09/23-2011 SDS No. 11103
12 ECOLOGICAL INFORMATION
ECOTOXICITY
There is no data on the product itself. The following information is provided on the basis of the individual component data available. The
product should not be allowed to enter soil, drains, sewers, ditches and waterways or be deposited where it can affect ground or surface
waters. See also Sections 5, 6, 7, 9 and 13.
BIOACCUMULATION
Based on the individual component data, the product is expected to bioaccumulate. Log octanol/water partition coefficient (Log Pow) is
expected to be greater than 3.0.
DEGRADABILITY
Based on the individual component data, the product is not expected to be readily biodegradable according to OECD/EC guidelines.
ACUTE FISH TOXICITY
Based on the individual component data, the product is expected to have experimental LC50/EC50/IC50 values between 1 and 10 mg/l in
most sensitive species.
13 DISPOSAL CONSIDERATIONS
DISPOSAL METHODS
GENERAL
Do NOT dump into any sewers, on the ground, or into any body of water. The product as shipped in its intended condition does not
exhibit any of the ‘Characteristics’ of hazardous waste as defined in 40 CFR 261.20-24. Disposal must be in compliance with all Federal,
State/Provincial and local laws and regulations. Regulations may vary in different locations. Waste characterizations are the responsibility
solely of the waste generator.
COMPONENT DISPOSAL
TRANSIT PACKAGING: shrink or stretch wrap, boxes and fittings that have not been contaminated with product should be re-used or
recycled. UNREACTED PRODUCT: empty uncleaned containers and contaminated packaging should be disposed of as non-hazardous
solid waste. REACTED PRODUCT: that has been mixed and cured in accordance with the relevant ‘Instructions For Use‘ will form an inert
filled polymeric compound that may be able to be disposed of as non-hazardous solid waste. Refer to your local licensed, permitted waste
agent or facility.
14 TRANSPORT INFORMATION
TRANSPORT NOTES Non-regulated for transport under current Domestic, or International Air and Sea Regulations.
Transport within user's premises: always transport in closed containers that are upright and secure.
Ensure that persons transporting the product know what to do in the event of accident or spillage.
15 REGULATORY INFORMATION
SECTION 313: This product does not contain toxic chemical subject to the reporting requirements of Section 313 of Title III of the
Superfund Amendment and Reauthorization Act of 1986 and 40 CFR Part 372.
U.S California Safe Drinking Water & Toxic Enforcement Act (Proposition 65): To the best of our knowledge, this product does not contain
any chemicals known to the State of California to cause cancer or reproductive toxicity.
Toxic Substance Control Act (TSCA): All constituents of this product are included on the Inventory or are not required to be listed.
5/ 6
REVISION DATE 09/23-2011 SDS No. 11103
16 OTHER INFORMATION
FIRE
(1)
HEALTH
(2) (0)
INSTABILITY
SPECIAL
GENERAL INFORMATION
Throughout this Material Safety Data Sheet; NIA = No Information Available; N.ap = Not applicable.
REVISION COMMENTS
REVISION. This material safety data sheet has been revised in the following Section(s): 9, 16, Replaces all previous versions.
Please observe the REVISION DATE. Should you be reading a material safety data sheet that is more than 24 months old or have
concerns over its validity, please contact your local Belzona Distributor or Belzona direct ([email protected]) and the most current
information will be sent to you.
REVISION DATE 09/23-2011
VERSION No. 1.2
DISCLAIMER
To the best of our knowledge, the information contained herein is accurate. However, some of the information presented and conclusions drawn are
derived from sources other than direct test data on the product itself and while Belzona Inc. believes such sources to be reliable, the information is
provided without any warranty regarding its correctness.
Since Belzona Inc. has no control over the conditions under which the product will be used, liability will not be assumed to exceed replacement or refund
of the purchase price of this product. Except as stated herein, there are no express or implied warranties including implied warranties of merchantability
or fitness for a particular purpose. Belzona Inc. assumes no liability for injury or incidental or consequential damage arising out of the storage, handling,
use or, disposal of this product.
6/ 6
REVISION DATE 09/23-2011 SDS No. 11104
2 HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Gray Paste. Amine odor. DANGER. Toxic if inhaled. Causes skin and eye burns. May be harmful if swallowed or absorbed through the
skin. May cause allergic skin or respiratory reaction. A component of the product may affect the liver, kidneys and respiratory system.
Possible risk of irreversible effects. Combustible liquid - Class IIIB. Prevent the product from entering into soil, drains, sewers, ditches or
waterways.
1/ 8
REVISION DATE 09/23-2011 SDS No. 11104
3 COMPOSITION/INFORMATION ON INGREDIENTS
COMPOSITION COMMENTS
The remaining constituents of this product are either considered to be non-hazardous or below the relevant concentration limits.
4 FIRST-AID MEASURES
GENERAL INFORMATION
In all cases of doubt, or when symptoms persist, seek medical attention. Never give anything by mouth to an unconscious person.
INHALATION
Remove to fresh air. Keep the patient warm and at rest. If breathing has stopped, administer artificial respiration. Give nothing by mouth.
If unconscious, place in the recovery position and seek medical advice.
INGESTION
If accidentally swallowed do NOT induce vomiting. Keep at rest. Rinse mouth with water and drink 1 cup of water every 10 minutes for 30
minutes. Seek immediate medical attention.
SKIN CONTACT
Remove contaminated clothing and shoes. Wash skin thoroughly with soap and water or use a proprietary skin cleaner. Do NOT use
solvents or thinners. If irritation or inflammation persists, seek medical attention.
EYE CONTACT
Contact lenses should be removed. Irrigate copiously with clean, fresh water for at least 15 minutes, holding the eyelids apart, and seek
medical advice.
5 FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA
Use: sand, alcohol resistant foam, carbon dioxide, chemical powder, water fog for larger fires.
Do NOT use water jet.
2/ 8
REVISION DATE 09/23-2011 SDS No. 11104
FLAMMABILITY CLASS
3.2 Combustible Liquid IIIB
PERSONAL PRECAUTIONS
Exclude sources of ignition and ventilate the area. Exclude non-essential personnel. Keep up-wind of spill to avoid breathing vapors. Do not
get in eyes, on skin, or on clothing. Refer to protective measures listed in Section 8.
ENVIRONMENTAL PRECAUTIONS
Prevent the product from entering into soil, drains, sewers, ditches or waterways in large quantities.
SPILL CLEAN UP METHODS
Scrape the majority of the product into a suitable labeled container. Cover the spill area with sand or other suitable inert material and sweep
up into the container. Clean surfaces down with a water and detergent mixture. Refer to disposal methods listed in Section 13.
HANDLING
GENERAL
Keep the container tightly closed when not in use. Vapors may collect in the container headspace during transit or prolonged storage.
Avoid breathing vapor when opening the container. Where possible open containers and mix components in a well ventilated place away
from the application area. Prevent air-borne concentrations higher than the occupational exposure limits (see Section 8). Exclude
non-essential personnel. Minimise the number of employees exposed and the duration of their exposure. Do not get in eyes, on skin, or on
clothing. Smoking, eating and drinking should be prohibited in areas of storage and use. For personal protection see Section 8. Always
keep in containers made of the same material as the supply container. Good housekeeping methods and regular safe removal of waste
materials should be observed.
FIRE/EXPLOSION
This product is combustible. Exclude sources of heat, sparks and open flame.
STORAGE
Observe the label precautions. Store between 5°C (41°F) and 30°C (86°F) unless otherwise stated in a dry, well ventilated place away
from sources of heat, ignition and direct sunlight. No smoking. Prevent unauthorized access. Store separately from oxidizing agents and
strongly acidic materials.
ENVIRONMENTAL STORAGE PRECAUTIONS
Spillage, incorrect storage of chemicals or waste materials or unsuitable disposal activities can result in pollutants seeping through the
soil, causing serious harm to groundwater- which is a vital source of drinking water. All wastes especially liquid wastes, should be securely
stored on site in designated areas that are isolated from waterways and groundwater and diked to contain any spillages.
3/ 8
REVISION DATE 09/23-2011 SDS No. 11104
COMPONENT IDLH
PHENOL 250 ppm
INGREDIENT COMMENTS
'T' = 'Transitional' Permissible Exposure Limit (PEL) set by OSHA. 'F' = 'Final Rule' Permissible Exposure Limit (PEL) set by OSHA.
'ACGIH' = Threshold Limit Value (TLV) set by ACGIH. 'Sk' indicates a risk of exposure through skin absorption. Consult local authorities for
acceptable exposure limits.
ENGINEERING MEASURES
Provide adequate ventilation. Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good
general extraction. If these are not sufficient to maintain concentrations of particulates and/or vapors below the relevant occupational
exposure limits, suitable respirators should be worn (see 'Respiratory Equipment' below).
RESPIRATORY EQUIPMENT
GENERAL GUIDANCE ON RESPIRATORY PROTECTION
It is essential that the concentration of the contaminant(s) in the application environment does not exceed the applicable occupational
exposure limit(s) multiplied by the Assigned Protection Factor (APF) quoted for the respiratory protective equipment selected.
STANDARD APPLICATIONS
Where necessary, it is recommended that an OSHA/NIOSH approved supplied-air respirator (SAR) equipped with a full facepiece is worn
if exposure to the applicator or other people nearby cannot be controlled to below the occupational exposure limit and engineering methods
cannot reasonably be improved.
EMERGENCY REPAIRS OR APPLICATION OF SINGLE UNITS
Where necessary, it is recommended that an OSHA/NIOSH approved air-purifying full facepiece or half-face respirator equipped with
appropriate vapor cartridge(s) should be worn. Where the application environment is likely to be contaminated by significant concentrations
of dust then the appropriate particulate prefilter (N-, R- or, P-series) should be worn in combination with the above. It is essential that the
facepiece is correctly fitted and the filter is changed in accordance with the manufacturer's instructions.
EMERGENCY SITUATIONS
Where entry into unknown or Immediately Dangerous To Life or Health (IDLH) atmospheres is required, an OSHA/NIOSH approved
pressure-demand self-contained breathing apparatus (SCBA) with a full facepiece or a pressure-demand supplied-air respirator (SAR) with
a full facepiece in combination with an auxiliary pressure-demand SCBA respirator should be worn.
HAND PROTECTION
GENERAL GUIDANCE ON HAND PROTECTION
The breakthrough time of the gloves selected should exceed the expected use period. Where this is not possible gloves should be
changed in good time, and in any case before the breakthrough time is exceeded. Where doubt exists, advice should be sought from
manufacturers or vendors of protective gloves in order to determine appropriate types for the particular circumstances. Barrier creams may
help to protect exposed areas of skin but are not substitutes for full physical protection. They should not be applied once exposure has
occurred.
SPECIFIC RECOMMENDATIONS
Use protective gloves made of: Neoprene. Nitrile.
STANDARD APPLICATIONS / EMERGENCY SITUATIONS
Medium-heavy weight gauntlet type gloves that provide wrist protection are suitable.
EMERGENCY REPAIRS OR APPLICATION OF SINGLE UNITS
Light weight disposable gloves are normally suitable.
EYE PROTECTION
STANDARD APPLICATIONS
It is recommended that eye protection, for example safety glasses with side shields or goggles are worn at all times during the handling
and use of this material. During subsequent machining, grinding, abrasion or removal of this product appropriate eye protection should be
selected according to the type of tools or equipment used.
EMERGENCY SITUATIONS
Refer to 'Respiratory Equipment' above.
4/ 8
REVISION DATE 09/23-2011 SDS No. 11104
APPEARANCE Paste.
COLOR Grey.
ODOR Amine.
PHYSICAL DATA COMMENTS This section contains typical values for Health, Safety and Environmental guidance only and is not
intended to represent a technical specification for the product. A = Alkaline.
SOLUBILITY Partially miscible with water.
BOILING POINT (°C) >100 (212°F) @ 760 mm Hg
MELTING POINT (°C) NIA
RELATIVE DENSITY 1.63 - 1.69 @ 20°C (68°F)
VAPOR DENSITY (air=1) >1
VAPOR PRESSURE 0.028 kPa @ 20°C (68°F)
EVAPORATION RATE N.ap
pH-VALUE, CONC. SOLUTION A
VISCOSITY N.ap
DECOMPOSITION TEMPERATURE >250 (482°F)
(°C)
ODOR THRESHOLD, LOWER NIA
FLASH POINT (°C) >110 (230°F) CC (Closed cup).
PARTITION COEFFICIENT NIA
(N-Octanol/Water)
STABILITY
Stable under recommended storage and handling conditions (see Section 7). In a fire, hazardous decomposition products such as smoke,
carbon monoxide, carbon dioxide, oxides of nitrogen and ammonia may be produced.
CONDITIONS TO AVOID
Keep away from oxidizing agents and strongly acidic materials to prevent the possibility of exothermic reaction.
11 TOXICOLOGICAL INFORMATION
TOXICOLOGICAL INFORMATION
*Estimated; according to the method described in Section 45 of the Controlled Products Regulations.
Name 2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL
Toxic Dose 1 - LD 50 1200 mg/kg (oral rat)
Toxic Dose 2 - LD 50 1280 mg/kg (dermal rat)
Toxic Conc. - LC 50 N/A.
Toxicological information
Risk of sensitization or allergic reactions among sensitive individuals.
5/ 8
REVISION DATE 09/23-2011 SDS No. 11104
12 ECOLOGICAL INFORMATION
ECOTOXICITY
There is no data on the product itself. The product should not be allowed to enter soil, drains, sewers, ditches and waterways or be
deposited where it can affect ground or surface waters. See also Sections 5, 6, 7, 9 and 13.
13 DISPOSAL CONSIDERATIONS
DISPOSAL METHODS
GENERAL
Do NOT dump into any sewers, on the ground, or into any body of water. The product as shipped in its intended condition exhibits the
following ‘Characteristics’ of hazardous waste as defined in 40 CFR 261.20-24: ‘Corrosivity’- RCRA Code: D002. Disposal must be in
compliance with all Federal, State/Provincial and local laws and regulations. Regulations may vary in different locations. Waste
characterizations are the responsibility solely of the waste generator.
COMPONENT DISPOSAL
TRANSIT PACKAGING: shrink or stretch wrap, boxes and fittings that have not been contaminated with product should be re-used or
recycled. UNREACTED PRODUCT: empty uncleaned containers and contaminated packaging should be disposed of as hazardous
chemical waste. REACTED PRODUCT: that has been mixed and cured in accordance with the relevant ‘Instructions For Use‘ will form an
inert filled polymeric compound that may be able to be disposed of as non-hazardous solid waste. Refer to your local licensed, permitted
waste agent or facility.
14 TRANSPORT INFORMATION
TRANSPORT NOTES Transport classification: labeling and packaging requirements may vary with pack and load size. Please
refer to the current transport regulations.
Transport within user's premises: always transport in closed containers that are upright and secure.
Ensure that persons transporting the product know what to do in the event of accident or spillage.
DOT PROPER SHIPPING NAME Polyamines, solid, corrosive, n.o.s. (containing Diethylenetriamine mixture)
TDG SHIPPING NAME Polyamines, solid, corrosive, n.o.s. (Diethylenetriamine)
ENVIRONMENTALLY No.
HAZARDOUS
SUBSTANCE/MARINE
POLLUTANT
DOT HAZARD CLASS 8
DOT PACKING GROUP III
UN NO. SEA 3259
IMDG CLASS 8
IMDG PACK GR. III
MARINE POLLUTANT No.
UN NO. AIR 3259
AIR CLASS 8
AIR PACK GR. III
6/ 8
REVISION DATE 09/23-2011 SDS No. 11104
15 REGULATORY INFORMATION
US FEDERAL REGULATIONS
PHENOL Yes.
SECTION 313: This product contains toxic chemical subject to the reporting requirements of Section 313 of Title III of the Superfund
Amendment and Reauthorization Act of 1986 and 40 CFR Part 372.
U.S California Safe Drinking Water & Toxic Enforcement Act (Proposition 65): To the best of our knowledge, this product does not contain
any chemicals known to the State of California to cause cancer or reproductive toxicity.
Toxic Substance Control Act (TSCA): All constituents of this product are included on the Inventory or are not required to be listed.
16 OTHER INFORMATION
FIRE
(1)
HEALTH
(3) (0)
INSTABILITY
SPECIAL
GENERAL INFORMATION
Throughout this Material Safety Data Sheet; NIA = No Information Available; N.ap = Not applicable.
REVISION COMMENTS
REVISION. This material safety data sheet has been revised in the following Section(s): 16, Replaces all previous versions.
Please observe the REVISION DATE. Should you be reading a material safety data sheet that is more than 24 months old or have
concerns over its validity, please contact your local Belzona Distributor or Belzona direct ([email protected]) and the most current
information will be sent to you.
7/ 8
REVISION DATE 09/23-2011 SDS No. 11104
DISCLAIMER
To the best of our knowledge, the information contained herein is accurate. However, some of the information presented and conclusions drawn are
derived from sources other than direct test data on the product itself and while Belzona Inc. believes such sources to be reliable, the information is
provided without any warranty regarding its correctness.
Since Belzona Inc. has no control over the conditions under which the product will be used, liability will not be assumed to exceed replacement or refund
of the purchase price of this product. Except as stated herein, there are no express or implied warranties including implied warranties of merchantability
or fitness for a particular purpose. Belzona Inc. assumes no liability for injury or incidental or consequential damage arising out of the storage, handling,
use or, disposal of this product.
8/ 8