WLA Handbook 3rd Edition - v2 - Web - PLT-EXE PDF
WLA Handbook 3rd Edition - v2 - Web - PLT-EXE PDF
HANDBOOK
3RD EDITION
2017
5
This Handbook is the property of TGT Oilfield Services, its subsidiaries and affiliates (“TGT Oil and Gas
Services”, “TGT Prime” or “we”), and is copyrighted. Unless separately and specifically authorised in
writing by TGT Oilfield Services, you may not copy, make derivative works, resell or distribute other than
as permitted in the Copyright Notice. TGT Oilfield Services, the TGT logo, TERMOSIM, SNL, EmPulse, MID
and the other names, marks, products and services described in the Handbook are either trademarks,
trade names or service marks of TGT Oilfield Services and its licensors, or are the property of their
respective owners.
The technologies listed below and their patents are the intellectual property of TGT Oilfield Services and
its subsidiaries:
LIST OF CONTRIBUTORS
Irina Aslanyan PhD in Molecular Physics, Senior Technology Advisor, Chief Editor
Sergey Matveev Technical Domain Champion, Compiling Editor
Artur Giniyatullin PhD in Technical Sciences, Analyst (Production Logging)
Yulia Maslennikova PhD in Physics and Mathematics, Lead Engineer Analyst (Spectral Noise Logging)
Roza Minakhmetova Technical Domain Champion (Pulsed Neutron-Neutron Logging)
Alexander Frolov PhD in Physics and Mathematics, Head of TSM Lab (Temperature Modelling)
Maxim Volkov Technical Domain Champion (Multi-Barrier Imaging)
The case studies presented in this Handbook were prepared by the Well Log Analysis Department of TGT Oilfield Services.
FOREWORD
This handbook is the result of many years of work in some areas of cased-hole logging that TGT specialises
in.
After a brief introduction to technology basics, most of the handbook's chapters expand on case studies
with references to SPE papers in which the reader can get even more details. Sixty cases have been
selected out of thousands of cases worldwide as the most representative for particular applications,
technologies or certain situations that can puzzle even the most experienced log analyst.
The geography of the cases covers 25 countries, on-shore and off-shore locations from Arctic ice through
deep forests to sunburnt deserts, sandstone and limestone formations, from high-permeability to shale
deposits, matrix and fractured formations, vertical, deviated and horizontal wells, hydraulically fractured
wells, a wide variety of single and dual completions, various types of packers and zonal isolations,
production by natural flow, artificial gas-lift, rod pumps and ESPs, oil and gas producers, water, gas and
water-alternated gas injection, steam and polymer injectors in green, brown and mature fields, from
no-pressure-support to gas-cap-drive, aquifer-drive and water-flood production.
The handbook is split into three major parts – well integrity, borehole flow profiling and reservoir flow
profiling, although the last two often overlap and make it difficult to determine to which part of the book
a case should belong – and aims to attract interest from cased-hole log interpreters, petrophysicists,
reservoir engineers and production technologists.
It particularly focuses on the tools that TGT has been developing over the last 18 years for PLT, spectral
noise logging, temperature logging, temperature simulations and pulsed electromagnetic corrosion
logging.
Most importantly, this handbook shares TGT's experience in integrated logging employing several tools
that provide more information than a simple sum of individual logs. In some case, such integration can
be tricky, and searching for a workaround can be a long chain of trials and failures.
Overall, it was a really exciting project and it will surely be continued to present new tools and applications.
We hope that our accumulated experience will be useful to log analysts across the world and that you
will enjoy your journey through this Handbook!
CONTENTS
2.1.4. Smart completion wells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 3.2.1 Corrosion Нole in a Long Tubing String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
2.1.5. Horizontal wells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
3.2.2 Corroded Tubing Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
2.1.6. Multi-well analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
3.2.3 Tubing Collar Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
2.2. Reservoir flow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
3.2.4 Casing Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
2.2.1. Quantitative analysis using the TermoSim simulator. . . . . . . . . . . . . . . . . . . . . . . 117
2.2.2. Step Temperature Response technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 3.2.5 Leaking Corrosion Holes in Tubing and Casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
2.2.3. Effect of daily and seasonal variations of injection water temperature . . . . . . . 130
Сhapter 3: SPE Papers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
2.2.4. Historical injection allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
2.2.5. Temperature gradient verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Сhapter 4: References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
2.3. Channelling identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
СHAPTER 1:
FUNDAMENTALS
FUNDAMENTALS
1 PRODUCTION LOGGING
СHAPTER 1:
1.1 PRODUCTION LOGGING nents and downhole equipment of the first
APPLICATIONS pipe barrier, i.e. tubing, casing, bridge plug,
SSD, etc.
Production logging (PL) is an essential part of •• Determination of flow rates for each phase
reservoir management as it is used to measure (oil, water and gas) from each producing
multiphase wellbore flow and detect well integ- zone
rity problems. The PLT survey is conducted in •• Determination of water or gas injection rates
both cased and open-hole sections of wells in for each injection zone
quasi-steady flow/injection or/and shut-in well
regimes. The combination of production logging other
technologies, such as Spectral Noise Logging
Generally, production logging is used for (SNL), Pulsed Neutron-Neutron Logging (PNNL)
and Multi Barrier Imaging (MBI) along with
•• Location of wellbore fluid entry points and the use of state-of-the-art data processing and
fluid types (water, oil or gas) mathematical modelling techniques to analyse
•• Location of fluid injection zones (water or processes in the wellbore and near-wellbore
gas) zone brings well logging to a totally new level.
•• Detection of leaks in the completion compo-
A PLT string consists of the following modules A typical configuration of an INDIGO-based pro-
measuring the corresponding parameters (with duction logging toolstring is shown in Fig. 1.1.
well log mnemonics abbreviated in parenthe-
ses):
•• INDIGO NAV-2 (GR, CCL and INCL)
•• INDIGO PT-2 and Micro-T (PRES and TEMP)
•• INDIGO Flowmeters (FBS and ILS)
•• INDIGO HEX-2 (HEX)
•• INDIGO ReCap-2 (COND and CAP)
•• INDIGO XYCaliper-2 (ID)
•• INDIGO Three-Arm Roller Centraliser (RC-3)
•• INDIGO Four-Arm Roller Centraliser (RC-4)
Application
INDIGO NAV-2 This sensor is used in radioactivity logging (RL)
to correlate recorded logs with lithologies and
The INDIGO NAV-2 module contains three sen- for other purposes:
sors: Gamma-Ray (GR), Casing Collar Locator •• Lithological differentiation and correlation
(CCL) and XYZ Inclination Accelerometer (INCL) of sedimentary rocks
measuring the deviation angle (Fig. 1.2). •• Identification of radiogeochemical anom-
Fig. 1.1. INDIGO production logging toolstring. alies caused by oil-water displacement in
Gamma-Ray Sensor (GR) cased wells
•• Identification of reservoirs
1.3. OVERVIEW OF PLT MODULES Operating principle •• Identification of minerals with higher or low-
Gamma-ray logging measures natural gamma er gamma activity
The INDIGO tool line is designed for logging and independently on batteries (Fig. 1.1). radiation that is specific to individual geological •• Rock shaliness evaluation
other operations in oil and gas wells, both open •• On-line operation facies.
and cased. Various modules can be configured to oper-
ate with a surface recording station through
single-core logging cable or coiled tubing
THE INDIGO CONCEPT •• Single-line power supply
This provides an opportunity to combine dif-
The INDIGO line of tools has the following main ferent tool modules in one toolstring in a re-
features: quired order, synchronise time and optimise
tool performance
•• ModularityEach module is a full-fledged •• Clean environment
tool with its own memory, so that individ- The INDIGO multi-module toolstring does
ual modules can be assembled into the tool not emit electromagnetic or acoustic waves
configuration required by the objective •• INDIGO Suite® software system
•• Power supply independence
All modules of the INDIGO line can operate
Fig. 1.2. INDIGO NAV-2.
Application ter than ILS to measure flow velocity inside cas- The limitations of this technique are low sensi- INDIGO HEX-2
The pressure sensor is used to measure ing. The ILS's internal diameter does not exceed tivity to low-velocity flows and the dependence
•• Bottom-hole pressure that of the main toolstring and can be used in of the sensitivity threshold on survey condi- The Indigo HEX-2 module (Fig. 1.6) has two
•• Wellbore pressure at any depth small-diameter casing and tubing. tions, presence of solid particles and flow com- sensors: the fast response high-precision tem-
•• Wellbore fluid levels position. perature (FRT) sensor and a wellbore fluid heat
•• Wellbore fluid density Operating principle exchange sensor (HEX). The temperature sensor
The sensor of a mechanical flowmeter is a Measurement units is integrated into this module to determine the
multi-blade turbine generating electrical signals The spinner module reads out turbine rotation- ambient fluid temperature.
INDIGO FLOWMETERS that are then recorded. The frequency of elec- al speed in RPS that is converted into flow ve-
trical pulses is converted into rotational speed, locity in meters per minute (m/min), meters per Operating principle
Mechanical flow meters measure the average which is directly proportional to linear flow ve- second (m/s), feet per minute (ft/min) or feet The HEX sensor is a heat flowmeter that mea-
velocity of mixture flow. The full-bore spinner locity. FBS is sensitive to both axial and radial per second (ft/s) through a calibration. sures the variation of the sensor’s temperature
FBS (Figs. 1.4a and1.4b) and in-line spinner ILS flow (Fig. 1.5), and its material and geometry (Fig. 1.7) occurring with variations in the veloc-
(Fig. 1.4c) are mechanical flowmeters for both provide high momentum transfer between flu- Application ity of the fluid that flows around the sensor [1].
open-hole and cased-hole wells. FBS is equipped id flow and spinner blades, thus ensuring a low Mechanical flow metering determines the flow It consists of a heating element that heats the
with expanding fingers and has a larger diame- spinner threshold. velocity of fluid, gas or their mixture in the well- HEX sensor and a temperature sensor that mea-
bore and is used for the following applications: sures its temperature. The temperature sensor
•• Location of inflow intervals in production and heating element are accommodated in one
wells and injection intervals in injection housing filled with thermal grease. The sensor
wells is sensitive to the temperature and velocity of
•• Determination of interval and total flow the wellbore fluid that flows around it. HEX data
rates are recorded during upward and downward tool
•• Detection of wellbore cross-flows after well passes and/or at stations.
shut-in
Fig. 1.4. (a) Full-bore spinner; (b) Full-bore spinner + Micro-T; (c) In-line spinner. Fig. 1.5. An FBS turbine and the directions of the flows pushing against its blades.
The sensor is most sensitive in the water holdup Wellbore electrical capacitance sensor
range of 60–100%. At lower water contents, the (CAP)
tool's response to water content variations is weak.
For this reason, the conductivity sensor is used in Operating principle
water-dominant flows with a water holdup of more The operation of the electrical capacitance
than 60%. It should be noted that its readings can be sensor (CAP) is based on different dielectric re-
substantially affected by the multiphase flow struc- sponses of gas, oil and water in the wellbore.
ture, oil viscosity and presence or absence of cen- Fig. 1.11 shows the schematic of the capaci-
tralisers in the tool string. tance sensor.
Fig. 1.10. Resistivity vs. water holdup for a two-phase (oil-water) mixture in the effective volume Fig. 1.11. Capacitance sensor schematic.
of the tool.
The dielectric permittivity, which is linearly pro- Operating principle horizontal wells, and inner wellbore diameters
portional to capacitance, varies between 50 and Application The module is an electromechanical system for that are too large to be measured by the tool.
80 relative units for water, 2 and 4 for oil, and The wellbore electrical capacitance sensor is independent measurements of two diameters
is 1 for gas. As a result, the capacitance sensor used for the following applications: and is used to continuously and simultaneous-
responds non-linearly to different phases in the •• Wellbore water holdup measurement ly measure and record two inner casing and/or INDIGO THREE-ARM ROLLER CENTRALISER
wellbore and is more sensitive to water. Accord- •• Location of water inflow intervals open-hole diameters.
ingly, its sensitivity changes with water content. •• Phase analysis of wellbore fluids (when used The compact Three-Arm Production Roller Cen-
Fig. 1.12 shows that the sensor has the highest in combination with the conductivity sensor) Measurement units traliser RC-3 (Fig. 1.14) accurately centralises
sensitivity at a water holdup of up to 40%. At •• Location of leaks in casing and downhole The measurement units of XYCaliper-2 are me- production logging tools in vertical and deviat-
higher water contents, the tool's response to equipment tres (m), centimetres (cm), feet (ft) and inches ed wells. Due to an electrical feed-through, it
water content variations is weak. Therefore, (in). can be used at any point of the string. The roll-
the capacitance sensor is used in oil-dominant ers ensure minimum friction on the way down
flows at a water holdup of less than 40%. It INDIGO XYCALIPER-2 Application the well.
should be noted that capacitance readings can The Indigo XYCaliper-2 module is used for the
be substantially affected by the multiphase flow The Indigo XYCaliper-2 module is a pipe caliper following applications:
structure, oil viscosity and presence or absence tool (Fig. 1.13). Adding INDIGO XYCaliper-2 to •• Inner diameter measurement INDIGO FOUR-ARM ROLLER CENTRALISER
of centralisers in the tool string. the PLT tool string substantially improves the •• Detection of casing ovality and collapse
quality of inflow and injection profiling and de- •• Detection of casing breaks and collar discon- The compact Four-Arm Production Roller Cen-
Measurement units termining total and interval flow rates, as the nections traliser RC-4 (Fig. 1.15) accurately centralises pro-
The output reading of the capacitance sensor is actual inner wellbore diameters may significantly •• Precise wellbore diameter measurement in duction logging tools in horizontal wells. Due to an
frequency measured in hertz (Hz). differ from the initial or specified ones. uncased intervals with caverns or deposits electrical feed-through, it can be used at any point
of the string. The rollers ensure minimum friction
The application of the technique is limited by on the way down the well.
deposits on the pipe's inner surface, decentral-
isation of the downhole tool in deviated and
Fig. 1.12. Frequency variation vs. water holdup for a two-phase (oil-water) mixture in the
effective volume of the tool.
Fig. 1.13. Indigo XYCaliper-2.
r
1.4. FLOW PHYSICS kVPCF=f(Re,—
R
), (1.3)
Depending on the composition, fluid flow can be In fluid mechanics, the Reynolds number Re is a
classified as single- or multi-phase flow. The first dimensionless number that provides a measure
type is in most cases found in gas or water injection of the ratio of inertial forces to viscous forces
wells, new oil or gas production wells or watered for given flow conditions [2]:
production wells, while the second in the major-
inertial forces ρvd
ity of mature production wells. In the most gen- Re= —
viscous forces = μ ,
——————— —— (1.4)
eral case, multiphase analysis can be performed
for four-phase fluid flow containing the following where
components: ρ – mixture density
v – flow velocity
•• Formation water d – inner pipe diameter
•• Injected water μ – dynamic viscosity
•• Oil or gas condensate
•• Gas The Reynolds number depends on the flow ve-
locity and is an important parameter that de-
FLOW PHYSICS BASICS scribes whether flow is laminar or turbulent [2]:
Fig. 1.14. Three-Arm Roller Centraliser RC-3. Determination of flow rates for fluid, gas or •• Laminar flow occurs at low Reynolds num-
a multiphase composition requires know- bers, where viscous forces are dominant,
ing their mean linear velocities. The flow rate and is characterised by smooth, constant
Q is related to the mean linear flow velocity v̅ fluid motion. Typically, Re is lower than 2300
as follows: •• Turbulent flow occurs at high Reynolds num-
bers and is dominated by inertial forces,
Q=v̅A, (1.1) which tend to produce chaotic eddies, vorti-
ces and other flow instabilities. Typically, Re
where Q is the well flow rate in m3/D, and A is is higher than 2300
the cross-sectional area in m2.
MULTIPHASE FLOW
The spinner and heat exchange sensor data pro-
vide the apparent linear flow velocity vAPP. The The flow-rate and multiphase sensors included
mean flow velocity is linearly proportional to in the Indigo PLT toolstring measure some av-
the apparent flow velocity: erage characteristics in the tool's cross-section
that depend on the multiphase mixture flow re-
v̅=kVPCF•vAPP, (1.2) gime.
where kVPCF is the velocity profile correction fac- In multiphase flow, typical flow regimes can be
tor that depends on the wellbore flow regime distinguished in terms of the relationship be-
and the spinner's geometry and defined as a tween phase superficial velocities.
function of the Reynolds number Re and the ra-
tio of the spinner's blade area radius r to the Examples of gas-liquid flow regimes in vertical
inner wellbore radius R [2]: and horizontal tubes are shown in Figs. 1.16 and
Fig. 1.15. Four-Arm Roller Centraliser RC-4. 1.17, respectively.
Vertical flows are conventionally classified as The difference between the velocities of dis-
follows: bubble flow, slug flow, churn flow, an- persed and continuous phases is called slip ve-
nular flow with droplets and annular flow (Fig. locity, v21:
1.16). When the gas-phase superficial velocity is
low, the bubble flow regime dominates. As the v21=v2̅ -v̅1, (1.5)
gas-phase superficial velocity increases, bub-
bles tend to coalesce and form Taylor bubbles, where v1 is the continuous phase velocity and
so that slug flow becomes predominant. With v2 is the dispersed phase velocity. Due to the
further increases in the gas-phase superficial slippage effect, measured cross-sectional phase
velocity, slug flow changes into churn flow and holdups do not correspond to their input vol-
then into annular flow, when gas moves in the ume fractions. A cross-sectional phase hold-
flow core and fluid along the pipe wall. If the gas up is defined as the fraction of the wellbore's
velocity is relatively low, some fluid may move cross-section occupied by a particular phase
in the gas flow core in form of droplets [3]. [4,5]:
A
Horizontal flows are conventionally classified as αi= —
A.
i
(1.6)
annular flow, dispersed bubble flow, slug flow,
elongated bubble flow, stratified wavy flow and There are a number of correlations – empirical,
stratified flow (Fig. 1.17). Horizontal and in- based on experimental data, and mechanistic,
clined pipes are characterised by an asymmetric based on the fluid mechanics principles – to de-
distribution of phases in the cross-section of a termine flow regimes and the slippage velocity
flow channel due to gravity [3]. v21. A brief description of the most widely used Fig. 1.17. Gas-liquid flow patterns in a horizontal tube [4,5].
correlations and the scope of their applications
In multiphase flow, each phase has a different are given in Table 1.1-Table 1.3.
relative velocity. The difference between phase Table 1.1 Gas-liquid (gas-oil or gas-water).
velocities depends on the physical properties
of the phases, well inclination and flow regime.
Model Deviation Regimes Comments
Model Deviation Regimes Comments 2.1 FLOW NOISE PHYSICS through a porous reservoir intermittently: a
fluid initially accumulates in a pore and then,
An empirical model in which slip velocity is deter- This section describes the physical principles of after a certain pressure is reached, slips into
mined using a family of curves representing the Spectral Noise Logging (SNL) and provides an an adjacent pore through a pore throat. The
Vertical and dependence of slip velocity on the phase density overview of papers on the generation of acoustic paper [15] presents an observation of oil flow
Choquette nearly verti- Bubble difference and specific heavy phase content αw noise by fluid or gas flows in a reservoir formation. through a heterogeneous porous medium. Fig.
cal wells (water hold-up). The model does not distinguish Although the theory of the generation of 2.1 shows how oil drops go into nearby pores
between hydrophilic (oil droplets in water) and acoustic noise by turbulent fluid or gas through pore throats (indicated by red arrows).
hydrophobic (water droplets in oil) mixtures flow through a pipe has been elaborated
in detail [11], its generation by fluid flow The paper [16] shows how frequency
Vertical and A semi-empirical model based on experimental through a reservoir formation is still poorly maxima in the acoustic noise spectrum of a
deviated survey data and drift flow model assumptions. understood. Numerous physical models have reservoir correlated with maxima in porosity
Nicolas & Witterholt Bubble and
wells devia- The model does not distinguish between hydro- been proposed in the last several decades to histograms. This study was carried out using
[10] pseudo-slug
tions of up philic (oil droplets in water) and hydrophobic analyse this process. Many of them are based core data from the wells that were then
to 70° (water droplets in oil) mixtures on the generation of acoustic noise by micro- surveyed by Spectral Noise Logging and shows
vortices appearing near pore walls due to their that the spectral pattern of acoustic reservoir
Stanford Drift Flux A semi-mechanistic model based on drift flux roughness and at pore throats due to an abrupt noise is governed primarily by the reservoir
Bubble and
Three-Phase Flow Model 0–88° theory and using empirically determined pa- change in diameter when a fluid flows through a formation structure.
pseudo-slug
(Liquid-Liquid) [8,9] rameters heterogeneous porous medium. They also take
into account elastic rock properties that have an In the general case, the frequency distribution of
additional resonance effect on acoustic noise the spectral density of acoustic noise generated
propagating through a reservoir. An experimental by fluid flow through a porous reservoir depends
Table 1.3 Three-phase (gas-oil-water). verification of this noise generation model is on the Rock Quality Index (RQI)
described in a paper [12]. Another paper [13]
k
describes the physical mechanism of acoustic RQI=0.0314√ ɸ (2.1)
Model Deviation Regimes Comments
noise generation by gas percolation through a
A semi-mechanistic model based on drift flux porous medium partially saturated with fluid i.e. on reservoir porosity ɸ and permeability k.
Stanford Drift Flux Three- theory and using empirically determined pa- wetting pore walls. An aerodynamic model of
Bubble to acoustic noise generation in a reservoir based Thus, the frequency of spectral maxima
Phase Flow Model (Three 0–88° rameters with continuity between different flow
annular on turbulence occurring when a fluid passes would remain the same for different reservoir
phase) [8,9] regimes. Applicable for gas holdups greater than
0.06 through a pore throat is given in the paper [14]. flow velocities but noise amplitudes would
vary, as defined by the geometry of porous
Another model, focused on fluid percolation media. In other words, the amplitude, or
through a reservoir as a source of acoustic power, of acoustic noise depends primarily on
noise, resulted from many years of well tests the fluid flow velocity and, therefore, on the
and laboratory studies (see the “Laboratory differential pressure related to the flow velocity
tests” section). by the motion equation. In general, noise power
increases with the product of flow velocity and
According to these tests, oil or water flows differential pressure because this
product is equivalent to the work performed by also depends on the fluid type. Laboratory
acoustic noise. studies show that the noise power is
Notably, motion equations that relate flow much higher for gas than for water or oil,
velocity to differential pressure are different when determined for equal flow rates and
for fluids and gases. Therefore, noise power differential pressures in the same reservoir.
The tool operates in memory mode on slickline SNL-9 is the ninth generation of Spectral Noise SNL-9 has the specialised Indigo interface that can Another application of SNL is the determination
and can be used in both vertical and horizontal Logging tools and has a wider dynamic range of synchronise measurements from several tools, of formation pressure in each reservoir unit of a
wells. In the latter case, coiled tubing or slickline 90 dB to record even very low noise, but still can as described in more detail in Section 1.3. This multi-layer field by conducting a survey in three
with a tractor has to be used. record data even in the presence of intense low- substantially enhances Spectral Noise Logging, and well regimes without shut-ins.
frequency noise generated by turbulent fluid it will, for example, be able to differentiate noise
All components of the tool are made of high- flow in the wellbore. This has become possible sources from the near and far zones around the
strength materials, and its electronic circuits due to the use of state-of-the-art high-quality well. The use of three synchronised noise logging FORMATION PRESSURE ANALYSIS
are assembled from high-temperature electronic components and specialised filters. tools will reduce the total survey time three-fold
components. As a result, the SNL Tool can be The detailed technical specifications of the SNL- without loss of spatial resolution. Formation pressure is an important indicator of
used to survey wells at temperatures of up 9 tool are given in Table 2.1. the amount of fluid left in the reservoir, which in
to 150°C and pressures of up to 60 MPa. The All SNL equipment is certified for compliance with the turn indicates the amount of energy available to
tool housing is made of titanium and can be GOST Certification System of the Federal Agency for drive fluid out.
used to log wells containing up to 30% hydrogen Technical Regulation and Metrology.
sulphide (H2S). There are two conventional techniques to
determine the formation pressure in wells that
Table 2.1 SNL-9 tool specifications. RESERVOIR FLOW ANALYSIS produce from single reservoirs:
1. Long-term pressure transient testing for
Pressure rating < 60 MPa (8,700 psi) SNL is a powerful technique for reservoir a bounded reservoir in which wellbore
flow analysis due to its ability to locate pressure build-up/fall-off is analysed. The
Temperature rating < 150°C (302°F) active reservoir flow units, although it wellbore pressure tends to, and at late times
cannot reliably calibrate noise volume becomes, the average formation pressure
LFP 8 Hz – 5 kHz in terms of flow rates because noise is a 2. A static wellbore pressure survey several
Operating frequency range complex function of several flow parameters, days after well shut-in when the wellbore
HFP 3 kHz – 58.5 kHz
most of which, including differential pressure, pressure is expected to recover to the
Frequency channels 1024 (or more) fluid type and reservoir rock properties, are average formation pressure
unknown.
Dynamic range 90 dB If a well penetrates several reservoirs, the
SNL data are visualised in the SNL data measured wellbore pressure is equal to the
Battery lifetime 70 hours panel to locate active flow units that can weighted average formation pressure for all
also be used as an input for TermoSim pTSM formations that communicate with the wellbore.
Casing material Titanium/Bronze
to start a matching procedure. In this case, the above techniques cannot be
H2S resistance up to 30% used to determine the formation pressure in
The integration of temperature simulation each reservoir.
Diameter 42 mm (1.65 in) (Section 1.4) and Spectral Noise Logging
provides a unique technique for volumetric Triple Production Logging (TPLT)
Length 816 mm (2.68 ft) assessment of behind-casing flow profiles.
Weight 7 kg (15.4 lb) This section describes a technique for determining
SNL data can also be used to analyse the origin and reservoir pressure by measurements at three
character of flow: for example, it can distinguish well flow rates in each flowing zone with spinner
between noises generated by the wellbore, logging and Spectral Noise Logging.
completion components, channelling, reservoir
rock matrix, casing leaks, gas bubbling and others. PLT profiling is conventionally employed in cased
wells to determine the formation pressure in
multi-reservoir systems by measuring inflows Thus, the determination of the pressure Pe at the As flow rate changes, the flow stabilisation used in calculations instead of the amplitude A,
from each perforated zone at different stable external boundary requires setting the rate Q at duration ∆t at each flow rate must be set is proportional to its square.
flow rates. However, its results in this application the sand face, duration ∆t and the pressure Pwf so that Infinite Acting Radial Flow (IARF) is
are far from adequate. for each flow rate. The formation pressure achieved before flow-rate measurements are In broader terms, it has been found experimentally
is determined by fitting the measured and made because equation (2.2) cannot be applied that the reservoir flow noise power is proportional
In a model case with a well of zero radius, or modelled operating pressures for the above to transient flows. Another factor is that the to the product of flow rate and differential pressure
a line source well, drilled through an infinite parameters (Fig. 2.3). In addition to the boundary conditions are often not known generated to create this flow:
homogeneous reservoir, the pressure at any formation pressure, two other parameters precisely, and flow-rate measurements should
distance from the well and at any time is are determined: the skin factor S, and mobile therefore be made within the IARF time window. N∝Q*∆P (2.3)
determined using the exact solution of the ratio.
diffusion equation: A Pressure Transient Analysis is normally This correlation was obtained and published in
This approach implies the assumption that performed to determine a time window for 1994 by Prof. McKinley (USA) and verified by
....(2.2) the formation pressure does not change IARF. A typical log-log diagnostic plot is shown TGT under laboratory conditions on the CAS-2
throughout the test, which can be the case in Fig. 2.4, with IARF displayed as a plateau. laboratory unit (Fig. 2.5).
hydraulic conductivity when production or injection is negligible
and transmissibility, relative to the amount of oil in place and the The TPLT method did not become a regular Fig. 2.6 shows the results of the noise power vs.
respectively. test period should be as short as days but not practice to determine formation pressure flow rate and differential pressure tests on the
months. because numerous cross-flows behind casing CAS-2 unit.
prevent fluid from entering the wellbore
laterally. As a result, well inflows are difficult Reservoir noise extraction
to correlate with their reservoir sources, which For accurate calculation of formation pressure, it is
can lead to substantial errors in the selection of required to determine the reservoir noise power.
input parameters. Taking into account equations (2.2) and (2.3), the
reservoir noise power N is related to the flow rate
Triple Spectral Noise Logging (TSNL) Q as follows:
Fig. 2.4. A log-log diagnostic plot for a typical PTA survey with the IARF regime over the 3 hours.
Fig. 2.5. The CAS-2 laboratory unit with the SNL sensor for the analysis of core samples measuring
25x50x70 mm at a maximum differential pressure dP of 10 bars.
t1,t2 and t3 and three surface flow rates Q1,Q2 and its highest accuracy at the end of the fitting
Q3 with three durations ∆t1,∆t2 and ∆t3 (see Fig. process.
2.8).
As mentioned above, a TSNL procedure, based
The net reservoir thickness of each flowing unit is
h
on flow-rate durations and pressure timings,
determined from SNL panel data. must be carefully planned to ensure that
pressure readings are taken when the wellbore
Out of the three fitting parameters (Pe, S and k), storage has disappeared for the SNL
the current formation pressure Pe usually reaches
Fig. 2.7. Reservoir noise in an SNL data spectrum** SPE 177620-MS [16].
Fig. 2.6. Noise power vs. flow rate and differential pressure data obtained on the CAS-2 laboratory unit.
tool to record sand-face flow noise that should However, if an active zone is not perforated
bestable by the time of recording. In practice, or covered by completion components – for
there is more than one pressure reading at each instance, when a reservoir of a dual-string
rate that PolyGon™ should fit, which usually well is producing through the shorter string –
increases the accuracy of formation pressure, the pressure in it can still be determined.
skin factor and permeability estimations. However, measurements in such a well should
be made in both strings to determine all required
TSNL’s advantages and limitations parameters: in the long string to survey the
The TSNL method has some limitations. One entire upper formation and in the short one to
of the most significant limitations is that it determine the bottom-hole pressure gradient
cannot be applied to no-flow zones with zero and extrapolate it to the top of the formation.
noise power, and the formation pressure can be
determined only for active flow zones. Notably, cross-flows behind casing do not affect
Fig. 2.8. Determination of formation pressure and skin factor by PolyGon™.
pressure determination for each hydrodynamically be logged – the distance between stations can be
independent unit, which is an advantage over increased to up to 3 m. To minimise the logging
Pressure Transient Analysis (PTA), Static Pressure time in long horizontal wells, measurements
Survey (SPS) and even Triple Production Logging can be made at 3-m intervals.
(TPLT) that is used to determine individual
formation pressures in multi-zone wells. Noise logging can be carried out during both
upward and downward passes. However, apart
The major advantage of this technology in terms of from the SNL tool, the tool string often includes
cost effectiveness is that it does not require a well to a temperature sensor that can measure the
be shut in, which minimises deferred oil production temperature accurately and continuously
and maintains injection at a desired level. during downward passes, and stationary SNL
measurements are made afterwards during
upward passes. An example of such a survey
visualised in the LogDesigner application is
shown in Fig. 2.3.
LOGGING PROCEDURE
The accumulation of data recorded at stations SNL DATA PROCESSING readings for further analysis and removal of
increases their statistical reliability. The standard uninformative signals generated by tool mo-
station time ranges from 40 seconds for leak According to the SNL tool’s specifications, the tion. This data analysis is performed on a set of
detection to 60 seconds for reservoir flow analysis digitisation frequency for high-frequency noise time-domain acoustic noise records made sole-
to ensure that enough data are accumulated with data is 120 kHz and the total operation time is ly at stations.
one standard 8-ms long noise record made every 72 hours. The SNL tool records large volumes
second. The SNL-9 tool makes records that are of data – 200 Mb to 2 Gb, depending on the During data processing, a noise frequency spec-
twice as long, i.e. 16 ms per second, which halves duration of the survey – which complicates their trum is calculated for each time-domain acous-
the station time. The maximum tool running time real-time transmission to the surface by cable. tic noise record by Fast Fourier Transformation
is also reduced two-fold from 72 to 36 hours. For this reason, all recorded data are written to (FFT). The resulting spectra are averaged for
the tool’s internal memory in both memory and each station and saved in LAS 2.0 format. The
In the zone of interest, stations are located at cable versions. overall spectrum for the entire depth interval is
1-m intervals. In some cases – for instance, in visualised as a colour spectral data panel (Fig.
leak detection when the entire wellbore has to The tool has to be withdrawn to the surface 2.5, SNL FLOWING data panel).
after each survey to download the recorded
time-domain acoustic data to a computer. The
dedicated SNL 2.0 plug-in synchronises the
obtained data with the depth sensor’s
SND data panel The resulting SND data panel contains only noise
generated by flow through the reservoir or holes in
Noises generated by flows through the reser- casing, with no background or depthwise-extend-
voir or holes are confined to certain depths (Fig. ed noise (Fig. 1.2.5, SND FLOWING data panel).
2.5). Low-frequency high-intensity noise, usu-
ally generated by wellbore fluid flow or pump Generally, the inner well diameter in the sur-
equipment, is not informative but often compli- vey interval may vary greatly, for instance, at
cates the identification of localised noise sourc- the tubing end. The character of acoustic noise
es. The Spectral Noise Drift (SND) technique has generated by fluid flow through completion com-
been developed to pin-point such depth-con- ponents can also vary substantially, both in ampli-
fined noise, both in the reservoir and at leaks. tude and in spectral composition. In such a case,
SND is a noise data processing technique that the SNDZ (Spectral Noise Drift by Zone) technique
takes into account both the time and frequency needs to be used to remove the wellbore noise
Fig. 2.4. (a) A standard SNL data panel; (b) A 3D shade data panel in a top view; (c) A 3D parameters of recorded noise signals to deter- component. This technique divides the survey
visualisation of an SNL data panel in a side view. mine their significance. interval into subintervals and selects optimal pro-
cessing parameters for each of them.
A detailed description of the SND algorithm can
be found in the paper [17].
SNL data panel weaker when both high- and low-intensity sig-
nals are present simultaneously.
The calculated and averaged noise spectra for
various depths can be visualised as a colour spec- An example of the SNL DREQ data panel is shown in
tral data panel (Fig. 2.5). Noise levels are indicat- Fig. 2.5. As seen in the figure, the spectral features
ed in colours: red for high-volume noise; yellow, have become equalised in intensity, and noise detect-
green, blue and violet for noise of lower volumes ed at Line А, previously invisible in the SNL FLOWING
in decreasing order; and white for noise below the data panel, has become distinct. Also, temperature
tool’s threshold. It should be noted here that nois- modelling indicates a flowing streak at this depth.
es of both high and low amplitudes simultaneous- The production profile determined by temperature
ly occurring in the SNL data panel impede noise modelling is shown in the QZI column.
visualisation and interpretation.
SNL relief shading
DREQ data panel
In many cases, small spectral features may be
Contrast equalisation and feature highlighting poorly visible against large ones. This can be
in the spectral data panel can be implemented improved by relief shading visualisation in the LINE A
by the Dynamic Range Equalisation (DREQ), a spectral data panels, as shown in Fig. 2.4. Fig.
post-processing technique to improve the con- 2.4 shows a standard SNL data panel (a), a 3D
trast in the SNL data panel. Contrasting spectral data panel in a top view (b) and the same panel
data panels are particularly useful for visualising in a side view (c). These representations make
all significant noises in one dynamic range and some signal features more distinct.
making weak signals stronger and strong ones Fig. 2.5. SNL, DREQ and SND panels for flowing conditions in a production well.
3 PULSED NEUTRON LOGGING Table 3.1. energy lines for all elements.
3.1 APPLICATION GAS INVASION Fluid ∑, c.u. Inelastic scattering reduces the neutron
energy to 1 MeV and then neutrons gradually
Fresh water 20–22
The Pulsed Neutron Logging (PNL) tool is used Another application of PNL is gas invasion slow down to a thermal energy of 0.025 eV
to locate watered, bypassed and uninvaded monitoring. The location of gas zones using Saline water, 20 g/l NaCl 29 (Fig. 3.1). Thermalisation of fast neutrons
hydrocarbon zones in both open-hole and neutron logging techniques is based on the takes approximately 10 s. A neutron loses
cased-hole wells. phenomenon that gas contains less hydrogen Saline water, 30 g/l NaCl 32.5
�
most of its energy when it collides with
PNL can be applied in the following cases: than water or oil, and the neutron count in a a nucleus of the same mass. On the other
gas reservoir is therefore lower. Saline water, 250 g/l NaCl 109.5 hand, when colliding with nuclei of different
WATER INVASION masses, the neutrons are not slowed down.
Light oil 16–18
HYDROGEN POROSITY Neutron energy loss upon collision is 100%
Determination of water saturation is based Heavy oil 20–22 for a hydrogen nucleus, 11% for an oxygen
on the different abilities of water and oil to In addition to saturation quantification, PNL nucleus and 6% for a silicon nucleus.
capture thermal neutrons. Chlorine present is effectively used to determine hydrogen Therefore, neutron slowing-down depends
in salt water enlarges its thermal neutron porosity, even in cased wells. Hydrogen Initial fast 14 MeV neutrons collide with nuclei primarily on the number of hydrogen atoms
capture cross-section. For this reason, PNL atoms are present in both water- and oil-filled in the wellbore, completion components and in the reservoir.
can distinguish high-salinity formation or reservoirs, and neutron counts can therefore formation rocks. The first collisions are mostly
injected water from hydrocarbons and can be used to estimate hydrogen porosity. inelastic. Inelastic scattering occurs when a When slowed down to thermal energy,
therefore estimate water saturation. neutron loses part of its kinetic energy to the neutrons are captured by nuclei, and this
scattering nucleus. When a nucleus returns process is accompanied by the emission of
from an excited state, inelastic scattering prompt capture gamma rays (CGR). Each
produces gamma rays (ISGR) with characteristic rock-forming element has its own CGR energy
3.2 PHYSICS
Pulsed neutron logging (PNL) is a well logging reservoir saturation and reflects the probability for a
technique based on the diffusion of thermal thermal neutron to be captured while moving a 1-cm
neutrons resulting from collisions of fast neutrons. distance. Sigma is measured in capture units (c.u.).
Thermal neutron diffusion is characterised by such
parameters as Thermal Neutron Mean Lifetime T; Table 3.1 shows capture cross-sections
Neutron Mean Free Path Λ between the point at for some fluids under normal conditions
which a neutron becomes thermal and the point (t = 20°C, P = 0.1 MPa).
at which it is absorbed by an atom’s nucleus;
and Thermal Neutron Macroscopic Capture Cross- Nonstationary thermalisation and capture of
Section Σ (Sigma). The PNL-determined Sigma neutrons in pulsed neutron logging occurs as
parameter is conventionally used to characterise follows.
Fig. 3.1 A neutron moderation cycle. A 14-MeV neutron “n” collides with a nucleus “N”. The nucleus
becomes excited (“N”) and emits a gamma quantum, and the neutron energy is reduced. This process
is called inelastic scattering. Several inelastic scattering events reduce the neutron energy to 1 MeV.
At that point, the contribution of elastic scattering to overall slowing down of neutrons increases.
Neutron gradually slow down to thermal energy (0.025 eV).
spectrum, and CGR data can therefore be neutron-neutron (PNN) logging. Capture
used for lithological analysis. gamma rays generated by the absorption of
slow, or thermal, neutrons after a neutron
Thermal neutrons reaching the near and far pulse are analysed in pulsed neutron-gamma
detectors are of primary interest in pulsed (PNG) logging.
PNN LOGGING TOOL TESTING AND Requirements for a calibration tank with fresh
CALIBRATION water
water under normal conditions, TRATwater, requires setting an invading fluid salinity. QUALITY CONTROL
equalling 8.4 c.u. (capture units). The curves used for salinity calculation are However, this information may not always
1. SBND (Sigma Borehole Near Detector) – be available, particularly if the invading fluid After processing all log data files, the following
CROSS-PLOTS FOR POROSITY CORRECTION Sigma of the borehole fluid at the near is different from the formation one, and this primary data are checked for quality:
FOR DIFFUSION detector makes current saturation determination less 1. Repeatability in the recording overlap
2. SBFD (Sigma Borehole Far Detector) – Sigma certain. The salinity of an invading fluid can interval.
The hydrogen index changes with formation of the borehole fluid at the far detector be determined by complementing pulsed 1. Standard deviations STDN (relative data
lithology and well parameters, including well 3. SFND (Sigma Formation Near Detector) – neutron-neutron logging with, for instance, approximation error for the near detector)
diameter and fluid salinity, and therefore Sigma of the reservoir formation at the near temperature measurements under shut-in and STDF (relative data approximation error
requires minor correction, normally 1 to 2 detector conditions. A temperature increase in the for the far detector). If the error exceeds
percent. Corrections for wellbore conditions, 4. SFFD (Sigma Formation Far Detector) – formation interval could mean formation 10%, the measurement is considered
i.e. cross-plots for diffusion corrections, are Sigma of the reservoir formation at the far water encroachment from below, and a unreliable.
determined in the laboratory [19]. detector temperature decrease could be caused by
lateral breakthrough of injected water.
THE SIGMA PARAMETER DETERMINATION OF CURRENT WATER
SATURATION. VOLUMETRIC MODEL
The exponential factors Σborh and Σform
in Formula (3.2) characterise absorption The salinity and water saturation are determined
properties. The atom of chlorine, a constituent using a petrophysical reservoir-well model in
of many salts dissolved in water, is an element which the rock consists of the rock matrix and
with an extremely large thermal neutron capture the pores filled with fluid, gas or their mixture,
cross-section. For instance, that of halite (NaCl) and the wellbore is filled with saline fluid.
is 770 c.u. [20].
In this case, the general formula to determine
Fluid salinity in c.u. can be expressed as the water saturation using the rock, formation
NaCl salt content of fluid using the following fluid and wellbore fluid Sigma values and the
equation: formation porosity is as follows:
Σwat[c.u.]=22[c.u.]+0.35*(NaCl)[ppk] (3.3),
ROCK PROPERTIES AND GEOTHERMAL The rock temperature initially formed by the as hundreds or thousands of years. Secular lateral temperature anomalies Θr developing over a
PROFILE Earth's heat flux can be disturbed by both flows in rocks substantially change the geothermal certain period of time (t) are defined by the
recent and secular lateral flows. For this reason, profile above and below a flowing reservoir. thickness of lateral flow, heat source power and
The Earth's heat flux is measured in the geothermal profile Tg (Fig. 4.1) is calculated thermophysical properties of rocks.
energy per square metre [W/m2]. This by the following formula: Recent lateral flows (Fig. 4.2, right) are fluid
flux has already stabilised and, therefore, z
z
dz flows caused by industrial activities taking Heat insulation properties of completion
the amount of energy is the same at any Tg ( z ) = Tref − q g ∫ 1 + ∫ S g (ζ )dζ (z)
λ ( z) place for up to several decades. Recent lateral components
depth. The Earth's heat flux ranges from z ref 0 flows in rocks create additional temperature Heat exchange between wellbore fluid, well
0.04 W/m2 to 0.15 W/m2 averaging at (4.1) perturbations (Θr) in the initial temperature components and surrounding rocks must be
0.06 W/m2. Different regions may have where gradient Tg and the regional geothermal profile taken into account for temperature calculations.
different heat fluxes. For example, the Earth's Z – upward vertical coordinate, or the distance is described as follows: This heat exchange depends on flow rate, well
heat flux through a tectonic plate is low from the reservoir bottom completion, wellbore fluid temperature Tf,
because of low seismic activity but is typically qg – Earth's local heat flux Tr=Θr+Tg (4.2) rock temperature Tw and flow type (laminar or
high in seismically active regions. Zref – geothermal temperature reference depth turbulent).
Tref – geothermal temperature at reference The vertical extent and amplitudes of the
Importantly, the thermal conductivity of rocks depth (zref)
increases with temperature and depends on the λ(z)(z) – thermal conductivity of surrounding
type of rock fluid. rocks
Sg – heat source of secular lateral flow
The initial temperature profile of a small oil
or gas field depends only on depth and does Secular lateral flows (Fig. 4.2, left) are fluid flows
not vary laterally, although the geothermal through reservoirs occurring for as long
temperature of large fields does vary laterally. Tg
TS
Average thermal conductivities for different rock types at 20°C are given in the table below.
The components of a complex well completion The calculated heat-exchange coefficients are Therefore, surface temperature variations occurs in a depth interval of 20–40 m. The neutral-
model include tubing, casing, annulus and used to calculate the temperature for each well are periodic and can be assumed to have the layer temperature is always 3.7°C higher than the
cement sheath (Fig. 4.3). Heat flow passes completion layer. following form: average annual air temperature.
through all well completion components from
tubing fluid through the casing annulus and Temperature modelling can identify anomaly T(t)=A cos ωt, (4.3) The following boundary condition is set
cement sheath to rocks. A specific temperature sources. For instance, a packer usually to model the temperature at the Earth's
is set for each layer: Tf – wellbore fluid produces a temperature anomaly under In this ideal case, the amplitude of temperature surface: the temperature at the interface
temperature; Ta – annulus fluid temperature; Tc shut-in conditions, and modelling can tell if variations depends on depth z as follows: between the air and the Earth's surface is
– cement temperature; Tw – rock temperature. it was caused by reservoir fluid flow or by the Tsurf (t), which changes in time and results from
Also, the following radii are precisely set: rf – inner difference in material properties between the (4.4) seasonal and daily temperature variations. The
tubing radius; rс – inner casing radius; rw – cement packer and behind-casing fluids, which often intensity of heat exchange between the air
sheath radius. The following fluid properties must leads to temperature anomalies. The greater the period of temperature variations, and the Earth's surface is defined by the heat-
be taken into account for accurate calculations: the deeper their penetration. Another factor that exchange coefficient αsurf.
λа – thermal conductivity of annulus fluid; HEAT EXCHANGE BETWEEN THE AIR AND THE affects the amplitude of temperature variations
λс – thermal conductivity of the cement sheath. EARTH'S SURFACE at depth is their amplitude at the surface. Daily THERMOHYDRODYNAMIC MODEL
air temperature variations occur in the soil layer
A procedure has been developed to calculate The near-surface rock layers are exposed to seasonal to a depth of 1–1.5 m. Temperature variations To model the thermodynamic processes
heat-exchange coefficients for all well and daily temperature variations caused by solar do not propagate instantaneously and occur at occurring in the well and reservoir during
completion components by taking into account activity and air temperature changes. depth some time after they do at the surface. injection and production, the TERMOSIM™
the properties of their materials and well fluids. Seasonal temperature variations penetrate to a simulator numerically solves two systems
depth of 20–40 m where heat is transferred mainly of coupled equations – hydrodynamic and
Surface due to thermal conductivity. For this reason, the thermodynamic, the TERMOSIM™ simulator
neutral layer, i.e. the constant temperature zone, numerically solves two systems of coupled
Tg initial h
Tg Tg initial
Secular Fig. 4.2. Geothermal profile affected by
Recent
lateral flow lateral (right) and secular (left) flows.
lateral flow
Tg initial – geothermal profile; Tg – geothermal
Tr profile affected by secular lateral flows; Tr –
qg qg geothermal profile affected by recent lateral
flow; qg – Earth's heatv flux.
Rocks
Tw Tc Ta Tf Q
Cement
Convection
equations – hydrodynamic and thermodynamic. conditions, mask the true reservoir temperature. Mass balance for each layer is determined by uniform within the reservoir interval, which has
The production/injection history of the well is As a result, the resulting measured temperature the following equation: been taken into account in modelling. A reservoir
divided into steps. A flow pattern is set for the profile is smoothed, which substantially inflow profile may be different from a wellbore
well and reservoir, which is followed by the complicates modelling. Q + Wbot = V + Wtop (4.7) inflow profile – for instance, in the presence of
calculation of temperature perturbations for cross-flows behind casing – and these profiles can
each time step. The hydrodynamic well model takes into account where V – rate of inflow from the reservoir, be set differently.
unsteady pressure build-up in a multi-reservoir Wbot – rate of behind-casing cross-flow from the
The simulator can model various flow patterns system. To calculate pressure for both the well bottom unit, Q – wellbore inflow rate, Wtop – Thermodynamic well and reservoir model
including those for wellbore and behind-casing and the reservoir, TERMOSIM™ numerically rate of behind-casing cross-flow to the top unit
cross-flows under both flowing and shut-in solves the pressure diffusion equation for (Fig. 4.5). In addition to the hydrodynamic equations
conditions. communicating reservoir layers and radial fluid described in the previous section, the
flow. Each reservoir unit is characterised by This equation implies that the total volume of fluid TERMOSIM™ simulator numerically solves a
Hydrodynamic model of single-phase well- pressure diffusivity (χ). All reservoir units are coming from the reservoir and behind the casing system of thermodynamic equations to calculate
reservoir flow assumed to communicate with the wellbore. from lower formations has to be equal to that of well and rock temperatures. The models of
The hydrodynamic models of well and reservoir Generally, formation pressures are different fluid entering the wellbore and then flowing behind injection and production wells are different
with single-phase flows are identical for in different layers, and this causes cross-flows the casing into overlying intervals. because temperature anomalies in them are of
injection and production wells. For this reason, between them during shut-in periods. In a different origins. For this reason, each model
this case describes a generalised hydrodynamic shut-in well, pressures in reservoir units build In many wells, inflow or injection profiles are not has to be described separately.
model valid for both types of wells. up differently because of different pressure
diffusivities. During the first hours, it can lead
The fluid is assumed to flow radially in the to cross-flow from a layer of high pressure
reservoir. Fluid flows in the well and reservoir diffusivity to one of low pressure diffusivity.
depend on the bottom-hole pressure Pwf, Then, after the reservoir pressure is stabilised,
formation pressure Pe at the external radial cross-flow can change direction in accordance
boundary re (at a 100-m radius from the well with the pressure at the external boundary.
or half the distance between neighbouring Depending on reservoir characteristics, the flow
wells), permeability k and skin factor S for each direction may change during the first hours or
production or injection zone. For producers Pe > days after well shut-in.
Pwf, and for injectors Pwf > Pe.
Flow velocity (u) and flow rate (V) in each
A hydrodynamic model can include two or more formation are defined by Darcy's law:
perforated or unperforated reservoir units,
if the latter communicate with the wellbore
k ∇p (1.4.5)
u= - — V= -2πr kh
— ∇p (4.6)
μ μ
through the casing annulus. Fig. 1.4.5 shows a
hydrodynamic model for a two formations. The flow rate depends on reservoir permeability
(k), reservoir thickness (h) and fluid viscosity (μ).
The model accounts for a wide variety of fluid To describe flow in a disturbed zone, its radius
flow patterns under both flowing and shut-in (rs) and skin factor (S) need to be set as well.
conditions. It should be taken into account that
wellbore and behind-casing cross-flows, often Fig. 4.5. A generic hydrodynamic model for a two-layer formation. Pe – formation pressure at the
appearing in multi-reservoir wells under shut-in external boundary, Pwf – bottom-hole pressure, Prc – pressure at casing radius, V – reservoir fluid
flow rate, Q – wellbore inflow rate, Wbot – rate of cross-flow from the underlying zone, Wtop – rate
of cross-flow into the overlying zone.
Injection wells Injection fluid temperature plays a key role There are two main techniques for injectivity conductive and convective heat exchange with the
In the generic thermodynamic model of an in forming reservoir temperature anomalies. profiling: DTR (Daily Temperature Response) reservoir as well as conductive heat exchange with
injection well, fluid injection changes the It may vary in time in a complex manner, and STR (Step Temperature Response). In the overlying and underlying rocks (Fig. 4.7). The Joule-
temperature of surrounding rocks through depending on the water-supply system: fluid DTR technique, the fluid injected into the Thompson effect in turn has two components:
conductive heat exchange. Generally, the flowing through onshore pipes to an onshore reservoir is affected by daily temperature friction heating and adiabatic cooling. For liquids,
temperature of injection fluid is lower than the well is affected by daily temperature variations, variations. Therefore, this technique is used in when they are forced through pores, the friction
geothermal temperature, and surrounding rocks while an offshore well would receive injection onshore wells. The STR technique employing heating effect prevails over the adiabatic effect
therefore cool down. Then, as the fluid flows fluid of nearly constant temperature. Another artificial temperature pulsing is used in offshore and a heating anomaly appears in the water/oil
through the reservoir due to convective and factor that affects the formation of temperature wells in which daily temperature variations do inflow interval. Because the adiabatic effect for
conductive heat exchange, a cooling anomaly anomalies is specific flow rate: the higher the not reach reservoirs. To generate temperature gas is greater than the friction heating effect, a
appears in the initial temperature distribution. specific flow rate, the deeper the penetration of pulses in a reservoir, a well is shut-in for some cooling anomaly appears in a gas inflow interval.
The more fluid enters the reservoir, the larger temperature anomalies into the reservoir. time, during which the wellbore fluid above the The maximum Joule-Thomson coefficient is 0.4°C/
and farther from the well the temperature reservoir is warmed by surrounding rocks, and MPa for oil, 0.22°C/MPa for water and -4°C/MPa
anomaly develops. The scale of temperature Quantitative injection profiling is based on then the warmed fluid column is injected into for gas.
perturbations in the reservoir depends on a large the combined analysis of flowing and shut-in the reservoir.
number of factors: injection rate history, seasonal temperature measurements to minimise the Water, oil and gas entering a producing well
and daily injection temperature variations, the number of uncertain input parameters. The Production wells affect wellbore temperature differently (Fig.
thermohydrodynamic characteristics of the formation injection profile can be determined In the thermodynamic model of a production 4.8). Water and oil production results in heating
reservoir and the heat insulation properties with minimal error by generating a temperature well, wellbore temperature is defined by two and gas production in cooling. Pure oil produces
of completion components. At the same time, pulse in the reservoir and analysing its response. factors: the Joule-Thompson effect and thermal the greatest heating effect. Some water in oil
fluid flow through the reservoir is accompanied mixing. reduces the temperature because of a lower
by conductive heat exchange between fluid Joule-Thompson coefficient. For a mixture
and overlying and underlying rocks. Fig. 4.6 Joule-Thompson effect containing 50% oil and 50% gas, heating will
illustrates heat exchange in an injection well. As fluid moves radially through the reservoir be lower than for an oil-water mixture because
towards the wellbore, it warms up or cools down pure oil flow produces a heating effect, while
due to the Joule-Thompson effect leading to both pure gas flow produces a cooling effect. For
a large amount of gas, the cooling effect is effect is normally caused by the difference
greater than the heating effect and the resulting between the temperatures of upward flow and
temperature is lower than the geothermal wellbore inflow due to the geothermal gradient.
temperature (Fig. 4.8). The resulting temperature is defined by the
heat capacities, flow rates and temperatures of
Thermal mixing mixing fluids.
Inflow of fluids of different temperatures from
different reservoir units into the borehole In the case when a heating effect occurs due to
results in their thermal mixing. water inflow from the lower production interval
(Fig. 4.9), the heated water goes up and its
Thermal mixing plays an important role in case temperature slowly decreases as a result of heat
of more than one flowing reservoir unit. The exchange with surrounding rocks. The degree
thermal mixing effect is displayed in temperature of temperature decrease depends on the flow
logs as a temperature gradient change. This rate, well design and the thermal conductivity
Fig. 4.9. A thermal mixing effect for a two-layer reservoir. The solid blue line indicates wellbore
temperature, the dashed blue line indicates inflow fluid temperature, and the green line indicates
the geothermal profile. The rightmost data panel displays an inflow profile showing uniform
water flow from the lower formation and uniform oil flow from the upper one.
Reservoir temperature
The simulator can also take into consideration
fluid breakthrough in the reservoir, and in this
Fig. 4.8. Effect of phase composition on temperature. case uses the changed temperature profile
where z – distance along hole, r – radial distance EmPulse tool specification General tool specifications are given in the table below.
from hole, σ (r, z) – electrical conductivity,
�
(r, z) –magnetic permeability, Eφ (r, z) – axial The EmPulse tool can contain up to three
component of electromagnetic field, j (r, z) – electromagnetic sensors (short, medium Table 5.1. EmPulse tool specifications.
generating coil current density, and 0 – vacuum and long). Each sensor consists of two coils:
� Parameter Value
magnetic permeability. generating and receiving. Both coils are
mounted concentrically around a composite
Operating temperature range -20…150 °С (-4…302 °F)
Equation 5.2 describes the variation of the core (see Fig 5.2). The EmPulse tool can detect
tangential component of the electric field for and analyse transverse and longitudinal defects Maximum pressure 100 MPa (14,500 psi)
the two-dimensional distribution of parameters in each of the first three coaxial metal barriers.
– in the radial (r) and axial (z) directions. The tool is effective in surveying pipes of various Maximum H2S concentration 30%
steel grades and weights, including those with
It can be seen that the response recorded by the high chrome contents, and its titanium housing Maximum pipe wall thickness 38 mm (1.5")
tool is governed by the magnetic permeability, enables operation in corrosive environments
Pipe diameter 51–381 mm (2"–15")
conductivity, the strength of the magnetic field with a hydrogen sulphide content of up to 30%
generated by the coils, diameter and thickness (Fig. 5.2). Recommended tool speed 2–4 m/min (6–12 ft/min)
of pipes as well as by the design of the tool itself
including its dimensions, current strength, etc. Stand-alone operating time 48 h
Short Sensor (5”) The Indigo Concept can be synchronised to avoid their mutual
The main common feature of the EmPulse tools interference.
with the Indigo interface is the Indigo single-
Long Sensor (19”) line bus 2.0 that supplies power to the tool The EmPulse tool comes in two versions for
and performs data exchange. This provides an different well completions: Indigo EmPulse
Medium Sensor (13”)
opportunity to combine different tool modules -2 and EmPulse -3. EmPulse -2 scans the first
(MBI, Navigator, Hex, PT, ReCap, SNL and others) and second metal pipe barriers up to 9-5/8"
in one toolstring in a required order. in diameter, and EmPulse-3 detects defects in
pipes with larger diameters of up to 14". These
The single-line bus enables the user to acquire modules can be integrated or used separately.
information about the connected tools, their If combined, the modules can evaluate the
current configuration and logging interval thicknesses of the first, second and third
duration, switch the recording sensors on and off, concentric pipes in one run.
upload a required survey scenario to the tools (in
memory mode), and read out data directly from The complete generation-and-recording cycle
the toolstring using a hardware adaptor and the takes 0.8 seconds for EmPulse-2, 1.2 seconds for
unified Indigo Suite software. EmPulse -3 and 2 seconds for their combination.
If possible, the modules should be used separately
The EmPulse tools can perform automatic self- to log at a higher speed of 4 m/min, while the
tests. Operation algorithms can be set for the recommended speed limit for their combination
tools to provide specific pulse durations and is 1–2 m/min.
Figure 5.2. EmPulse-2 and EmPulse -3 tool designs. periods. Several tool modules in one toolstring
EmPulse-2 defect sensitivity data are given in Table 5.2. Sensitivity of EmPulse -2 Barrier thickness accuracy Specification
the table below. to defects.
Barrier 1 ±3.5% (±0.01 in. or ± 0.25 mm for 3 ½’’ tubing with 7 mm wall thickness)
Completion pipes (in) Thickness Minimum hole size Minimum hole size in Barrier 2 ±6% (±0.03 in. or ± 0.75 mm for 9 ⅝’’ casing with 12 mm wall thickness)
Barrier 1 Barrier 2 in Barrier 1 Barrier 2
2⅞ + 15 mm 0.6 in
5½ + 40 mm 1.5 in
Completion, inch Minimum hole Minimum hole Minimum hole
7 + 50 mm 2 in size in Barrier 1 size in Barrier 2 size in Barrier 3
9⅝ + 65 mm 2.5 in 7 2 in 51 mm
13 ⅜ + 90 mm 3.5 in 9⅝ 2.5 in 65 mm
Completion, inch Minimum hole size Minimum hole size Minimum hole size DATA ACQUISITION after the start of decay recording.
in Barrier 1 in Barrier 2 in Barrier 3
The short EmPulse -2 sensor generates short, The medium EmPulse -2 sensor is optimised to
7 + 13 3/8 2.1 in 53 mm 6 in 152 mm low-amplitude electromagnetic pulses that scan metal barriers from 5" to 13" in diameter
magnetise mainly the first barrier and then for the first one and up to 9-5/8" for the second
9 ⅝ + 13 ⅜ 2.6 in 66 mm 6 in 152 mm records magnetisation time decays. It is most one. This sensor generates electromagnetic
commonly used for tubing inspection but can pulses with an amplitude larger than that for
2⅞+5½+7 0.7 in 18 mm 3 in 76 mm 6 in 152 mm
also work in moderate-size casing of up to 5" in the short sensor. Before 0.05 seconds (Fig. 5.4),
3 1/2 + 5 ½ + 7 0.8 in 20 mm 3 in 76 mm 6 in 152 mm diameter. The length of the sensor defines the magnetisation decays uniformly throughout the
minimum detectable size of defects, which is second barrier in all its components including
4 1/2 + 5 ½ + 7 0.9 in 23 mm 3 in 76 mm 6 in 152 mm 0.9" for the short one. If a defect is larger than collars. The magnetisation decay starts to
the smallest detectable one, magnetisation deviate from nominal 0.05 seconds after
2⅞+5½+9⅝ 0.7 in 18 mm 3 in 76 mm 7 in 178 mm decay in this zone is faster than for nominal. recording begins, i.e. much later than could be
3 1/2 + 5 ½ + 9 ⅝ 0.8 in 20 mm 3 in 76 mm 7 in 178 mm Accordingly, if any extra metal, such as a collar, expected due to a defect in the first barrier (Fig.
gets into the tool's radius of investigation, the 5.3). This observation can be used to distinguish
4 1/2 + 5 ½ + 9 ⅝ 0.9 in 23 mm 3 in 76 mm 7 in 178 mm magnetisation decays longer than nominal. corrosion occurrences in the first, second and
Therefore, the magnetic-field amplitude third barriers (Fig. 5.4).
2⅞+7+9⅝ 0.7 in 18 mm 3.3 in 84 mm 7 in 178 mm recorded in the collar zone would remains
larger than nominal throughout the decay (Fig. The long EmPulse-3 sensor generates long, high-
3½+7+9⅝ 0.8 in 20 mm 3.3 in 84 mm 7 in 178 mm
5.3). Magnetisation decay starts to deviate from amplitude electromagnetic pulses and records
4½+7+9⅝ 0.9 in 23 mm 3.4 in 86 mm 7 in 178 mm nominal not at the beginning but 0.003 seconds longer magnetisation decays. The
5 ½ + 9 ⅝ + 13 ⅜ 1.6 in 41 mm 5.5 in 140 mm 8 in 203 mm Fig. 5.3. Electromagnetic decays recorded by the short 5" sensor in the 4-½" metal barrier for a nominal
thickness zone (black curve), a 10% corrosion zone (red curve) and a collar (green curve).
7 + 9 ⅝ + 13 ⅜ 2.1 in 53 mm 5.5 in 140 mm 8 in 203 mm
recorded responses reflect the conditions of characterised by the longest observation time and
the first, second and third barriers of up to 14" digitises decay data into 91 channels. Thus, the
in diameter. The deviation of magnetisation tool records a total of 181 channels in one run.
decay from nominal at collars and defects in
the third barrier occurs later than at those in Data Acquisition Procedure
the first and second barriers (Fig. 1.5.5). The A MBI survey can be conducted during both
presence of corrosion or a defect speeds up downward and upward tool runs. However,
magnetisation decay while collars slow it down. recording is recommended to be performed
Notably, corrosion and collars are displayed in during upward runs because of the more stable
magnetisation decays at different times because tool speed. Although there are no special
the deviation of the recorded electromagnetic requirements for well operation, the tool may
decay from nominal in corrosion zones occurs move intermittently and thus affect the data
earlier than at collars. Corrosion in each barrier recording quality if the first metal barrier has a
appears in magnetisation decay data within the small diameter or if the well is producing at a
same time interval in which the response of the high rate. Any downhole electrical equipment,
corresponding collar is detected. such as an ESP, cathodic protection or pressure
and temperature gauges, may also affect tool
Electromagnetic decay data recorded by the operation and recorded data. For this reason, all
short 5" sensor are digitised into 42 channels. downhole equipment must be turned off before
The medium 13" sensor records decay into a well survey. Fig. 5.5. Electromagnetic decays recorded by the long EmPulse -3 sensor through the 4-½" tubing and
51 channels, while the long 19" sensor is 9-5/8" casing for a nominal thickness zone (black curve), 10% corrosion (red curve) and a collar in the
13-3/8" casing (green curve).
Fig. 5.6. A typical MBI logging procedure, with the logging tool run to the bottom of the survey interval Radial Distance, mm Radial Distance, mm
and recording made during an upward pass at a stable speed of not more than 6 m/min to the top of
the interval.
Electrical current, a.u. Magnetic field
B
This is implemented with the 2D MBI simulation MBI modelling is a highly complex multi-
software, based on the numerical solution of parameter mathematical process. Numerous
Maxwell's 2D axial symmetric equations (2), that laboratory tests suggest that electrical
uses an algorithm simulating sensor responses. conductivity and magnetic permeability
The simulator takes into account the tool's remain reasonably constant along a factory
geometry including centralisers and simulates the pipe joint (usually 33-ft long each) and depend
responses of several sensors simultaneously in two on the steel type and aging, while completion
dimensions – along the well and radially (Fig. 1.5.8). components and corrosion zones are unlikely to
occur throughout the joint.
Fig. 5.9 shows how accurately EmPulse tool
readings can be matched with the 2D numerical This observation allows the modelling procedure
model. to be done in several stages. In the first stage,
Fig. 5.10. MBI modelling results for the first barrier (7" casing) with the best fit obtained at 7.5-mm
pipe wall thickness (green curve).
the algorithm analyses tool responses at all This algorithm is called Real-Time Fitting
depths using depth-correlated trends and (RTF) because it models responses and
recognises pipe collars and joints in all barriers. performs fitting for modelled and measured
Then it decomposes each barrier into numerous ones immediately in the process of thickness
joints between the collars and creates a list of calculations.
wellbore intervals containing all barriers but no
collars. As the next step, it analyses all decays The RTF algorithm is auto-calibrated and accounts
for each joint, selects statistically representative for any combination of concentric pipes without
decays and, assuming that electrical conductivity requiring inputs on the steel grade, aging factor
and magnetic permeability are constant along or specific completion designs because the steel
the pipe joint (although they can be different types can be determined by the product μ∙σ of
for different pipe barriers), changes these two magnetic permeability and electrical conductivity
parameters and thickness across the pipe joint and are output in the modelling process put
to provide the best fit to the tool response into a separate data panel. This often allows
(Fig. .5.11). Ultimately, it generates a thickness the recognition of non-standard pipes, such as
profile, an electrical conductivity profile and a those of alloy steels that may contain different
Fig. 5.9. Fitting the measured magnetisation decays (dots) and modelled ones (solid lines) for all magnetic permeability profile for each of the concentrations of chromium or magnesium.
three sensors of the EmPulse tool. three barriers (Fig. 5.11).
Fig. 5.11. The results of numerical modelling for thickness determination. Black dashed lines in the TUBING and
CASING columns denote nominal tubing and casing thicknesses, and green solid lines in the Thickness 1, Thickness
2 and Thickness 3 columns denote simulated tubing and casing thicknesses from the EmPulse response. The
blue filling indicates the zones in which the simulated thickness is higher than the nominal, and the brown filling
indicates the zones in which the thickness is lower than the nominal. Electrical conductivity (σ) and magnetic
permeability ( ) in their respective columns are for steel types in each tubing or casing joint. Fig. 5.12a. Laboratory test results: measured
� and nominal wall thicknesses of the first and
second pipe barriers, 3-½" and 9-5/8", change in
a correlated manner. The green and blue curves
Pipes may have remanent magnetisation due to remnant magnetisation signal. The MBI simula- indicate the modelled wall thicknesses of both
the following factors: tor automatically filters out this parasitic mag- pipes and take into account their variations in
•• Downhole electrical equipment netic signal from the response recorded by the the first barrier that affected the wall thickness
•• Mechanical stress caused by torsion, bending, tool. calculation for the second one.
etc
•• Friction between a drill pipe and a casing TECHNOLOGY VERIFICATION BY LABORATORY
during drilling TESTS
•• Transportation and storage
Intensive laboratory tests were conducted to
Remanent magnetisation significantly distorts determine how the EmPulse tool responds to
the recorded signal, especially when the tool various defects in the first, second and third
speed increases. This distortion can be filtered downhole pipe barriers. Such tests can evaluate
out because it produces the same effect in each the quality, sensitivity and reliability of tool sensors
time channel of the tool. At late times, when and electronics and the technology in general by
the eddy current dies out, the signal recorded modelling different well completion designs with
by the EmPulse tool contains only a background various combinations of pipes.
Test 1. Determination of minimum wall of a 3-½" pipe increased as that of a 9-5/8" 9-5/8" pipe as an intermediate casing, and a examine the ability of the EmPulse tool to
thickness loss for each barrier in a dual-barrier pipe decreases.The discrepancy between the 13-3/8" pipe. A 7-½" hole was drilled in the last identify a defect in the second pipe barrier of
pipe assembly modelled and actual thicknesses was less than casing joint, which is equivalent to a uniform a three-barrier completion and to calculate
0.4 mm (6%) for the first barrier and less than metal loss of 8.8%. the thicknesses of the first three barriers.
A laboratory test conducted to determine the 0.8 mm (8%) for the second one.
tool's sensitivity to minor metal loss in a dual- Fig 5.13 shows the results of this laboratory The test model consisted of 9-5/8", 13-
barrier completion is described below. A dual- Test 2. Quantifying the smallest defect in the test. The modelled wall thickness curve for 3/8" and 18" casing joints inserted into one
barrier system used in the test consisted of 3-½" third barrier (13-3/8" pipe) the 13-3/8" pipe clearly indicates a defect. The another. A 7-½" hole was made in the 13-3/8"
and 9-5/8" pipes, both 3 metres long and evenly metal loss at this defect was calculated at 6.7%. pipe, which is equivalent to a uniform metal
ground circumferentially at 0.75-metre intervals These laboratory tests were conducted to No significant deviations from the first and loss of 8.8%. The objective was to identify
to gradually reduce pipe wall thickness. examine the tool's ability to identify defects in second barriers' responses were observed in defects in the first three barriers.
the third pipe barrier, which is normally 13-3/8" the defect's time interval.
Fig. 5.12a illustrates a laboratory test using a surface casing, as well as to demonstrate the Fig. 5.14 illustrates the results of this laboratory
setup including both pipes (3-½" and 9-5/8"), tool's sensitivity to defects in large-diameter Test 3. Quantifying the smallest defect in a 13-3/8" test. A defect in the second barrier (13-3/8"
with thicknesses decreasing with depth in a pipes in general and its ability to determine the pipe string in the presence of a 18" pipe string pipe), clearly identified as considerable metal
correlated manner. thicknesses of the first three barriers. loss, was calculated at 6.7%.
Another laboratory test was conducted to
Fig. 5.12b shows the results of laboratory One of the test setup arrangements is described
tests on a system in which the wall thickness below. The setup included a 3-1/2" pipe, a
Fig. 5.13. EmPulse -3 laboratory test results: a defect detected in the third barrier (13-3/8" pipe) and a defect in Fig. 5.14. EmPulse -3 laboratory test results: (a) A defect made and detected in the second barrier of
the third barrier producing no effect on thickness calculations for the first and second barriers. a triple-barrier setup of 9-5/8", 13-3/8" and 18" pipes.
ADVANTAGES AND LIMITATIONS OF THE INDIGO •• Time and processing power consuming is quite complex. For this reason, this
MBI TECHNOLOGY •• Evaluation of corrosion in stainless steel interpretation technology requires computers with high
pipes The algorithm for thickness modelling is CPU power ensuring accurate and efficient
The Indigo MBI technology is based on time The survey can also be conducted in based on time-domain analysis of responses thickness and metal loss calculations.
domain data recording and magnetisation decay corrosion-resistant stainless-steel pipes. recorded by the tool, and this algorithm
modelling providing a cutting-edge advantage
in the analysis of multi-barrier structures for •• Operation in memory or surface read-out
accurate evaluation of the effect of pipe wall mode
thickness variations in one barrier on determining The EmPulse tool can be run on slickline or in
the thicknesses of the others. surface read-out (SRO) mode. Depending on
client preferences and cable availability, the
The Indigo MBI technology has the following tool could be adapted to run in both modes,
advantages and limitations. which eliminates logistical problems.
Advantages: Limitations:
СHAPTER 2:
CASE STUDIES
•• Micro T – High precision temperature sensor 1. Production History and latest tests for all
СHAPTER 2:
•• RFI/RFP Temperature Simulators – offset wells
temperature modelling software for 2. Formation tops and perforations for all
Radial Flow Injection (RFI) and Radial Flow offset wells
Production (RFP)
2. Methodology Inputs for Job Proposals
•• Location of injection and inflow zones across 1. Latest production tests
perforated intervals 2. Well sketch
•• Evaluation of multiphase and injection flow 3. Formation tops
rates across perforations
•• Identification of wellbore cross-flows under Inputs for Interpretation and Analysis
shut-in conditions Raw logs recorded by TGT
1. Inflow profiling by a mechanical spinner and Spinner readings show a very good resolution 2. Injectivity profiling by a mechanical spinner The table below shows a good match between
a salinity and capacitance tool and stability which allows for the identification the fullbore spinner and surface test data:
of a fine-structure inflow profile: one can clearly Example 2 (Model case)
Example 1 (Model case) discern two inflow streaks against the upper This example shows how the fullbore spinner
Water, m3/d
The example below shows how PLT captures the perforations. provides a high resolution injection profile.
inflow zones across two perforated intervals. Spinner data shows 5 injection intervals localized Surface Test Data 183
within perforated zones.
Fullbore Spinner 190
The table below shows a good match between the fullbore spinner and surface test data:
3. Comparison of the injectivity profiles calibration – similar to the one used in spinner Example 2 (Model case) completely missed. HEX survey provides more
obtained by a mechanical spinner and the HEX interpretation. The table below shows a good The example below shows HEX survey in accurate description of injection scenario and
tool match between HEX and surface test data: horizontal well where spinner readings are clearly shows the zones of fracture and matrix
poor and missing large zones of injection. injection.
Example 1 (Model case) Spinner has captured only one injection zone
The example below shows a good match Water, m3/d which is attributed to the open fracture while
between HEX and spinner profiles. One can see the injection into the matrix reservoir was
that injection profile QZI_HEX from HEX survey Surface Test Data 242
is less noisy than spinner profile and provides
better resolution. It clearly shows fine structure HEX 245
of injection units which is missed on spinner.
Fullbore Spinner 240
Injection rates are evaluated through the HEX
Injection rates are evaluated through HEX calibration. The table below shows a good match between
HEX and surface test data:
Water, m3/d
HEX 672
a fault, although the high-frequency portion of showed that the Е1 reservoir unit produced inflow profile. This objective was achieved by A production profile was constructed using the
the noise suggested fluid flow through a porous about two-thirds of the total oil inflow. It can integrated high-precision temperature and temperature simulator. The simulation results
reservoir. Most probably, the fluid initially thus be concluded that oil entered the wellbore spectral noise logging (HPT-SNL) [25]. showed that the main inflow through the short
flowed through the fault and then entered mainly through the fault and fault-related string (84%) occurred within the upper perforated
the rock matrix. The temperature simulation fractures. Analysis of SNL data identified reservoir intervals interval. The lower perforated interval had only
with fluid flows: Zone 1 and Zone 2. According minor flow. Thus, the simulated production profile
to the noise frequency distribution, most of the based on temperature measurements correlated
fluid was produced through fractures generating with the SNL noise distribution.
1–1.3 kHz noise. Some fluid flowed through the
matrix, as indicated by slight 1.7–2.0 kHz noise. Analysis of reservoir fluid at the surface
2.1.2 DUAL-STRING COMPLETIONS indicated that the gas-oil ratio did not change
The A2 reservoir unit produced through two throughout the production process, which
Example 1 (Job ID-11058) the long tubing string and the A1–A3 interval was perforated intervals. However, low-frequency indirectly meant that the pressure in the upper
This case presents a deviated dual-string therefore logged through a barrier, being the noise recorded within the unperforated А1 reservoir units was still above the bubble point
well selectively producing from the reservoir tubing. In this particular case, all conventional reservoir unit and some portion of A2 indicated pressure. This was confirmed by low-amplitude
units A2 and B through long and short tubing, techniques—the spinner, multiphase sensors, downflow behind casing from these units that noise recorded by SNL.
respectively. All measurements were made in pressure gauge, etc.—failed to determine an significantly contributed to overall production. The deviation between the static and flowing
Noise generated by another behind-casing temperatures below the packer was due to
flow was detected in the top portion of the production from the underlying reservoirs
unperforated A3 reservoir unit (Fig. 1). through the long string.
Fig. 1. HPT-SNL during inflow through the Short String. Fig. 2. HPT-SNL during inflow through the Long String.
Spectral Noise Logging detected a 0.4–7.5 kHz gas content. The modelled profile matched the occurred in Zone 4. The salinity, capacitance and Temperature modelling and Spectral Noise
signal in A5 reservoir. The signal amplitude interpreted SNL data (Fig. 1). temperature modelling data indicated water Logging were used to determine the inflow
in Zone 3 was much lower than in Zone 1 or in this inflow. In Zone 5, fluid inflow was 28 profile of the A2 – A6 reservoirs and identified
Zone 2. In addition, the F1D1 high-precision Production through the long string percent of the total inflow under bottom hole intense gas inflow zones in A3 and A4 reservoirs.
temperature curve showed a heating anomaly A combined analysis of High Precision conditions. Additionally, about 4 percent of the Another finding was upward cross-flow behind
in the A5 reservoir. The above phenomena Temperature and Spectral Noise Logging data total inflow was allocated to below the survey casing from A5 reservoir and subsequent entry
suggested the absence of free gas from the A5 identified inflow intervals for the A6 reservoir interval. No free gas was detected in inflow into the wellbore at the bottom of A4 reservoir.
reservoir. in the open hole section (Zone 4 and Zone 5). At under bottom hole conditions. Water cut was The survey revealed no leaks in the production
the top of А6 reservoir and above, SNL detected 21 percent. The modelled profile matched with casing, tubing or packers and no communication
Above Zone 1, SNL detected a high-amplitude, a high-amplitude 0.1–6.3 kHz signal generated the interpreted SNL data (Fig. 2). between tubing strings.
low-frequency signal generated by upward by upward fluid flow through the long tubing
wellbore fluid flow. According to temperature string.
modelling, as much as 91 percent of fluid
inflow occurred between A3 and A4 reservoirs. According to temperature modelling, as much as
Inflow from lower A5 reservoir was small and 68 percent of fluid inflow from the A6 reservoir Example 3 (Job ID-11036) conducted in this well was to profile inflow from
fluids from A3 and A4 reservoirs had high free This case presents a horizontal dual-string the perforations within Reservoir Units D1–D3
oil well selectively producing from different and to detect communication between the
portions of Reservoir D through long and short and long strings.
short tubing. The main objective of the survey
A difference of 10 psig between the static and flowing SNL at the packer. Flowing temperature
flowing pressures in the short string indicates modelling determined a production profile
inter-string communication. This cross-flow for the perforated intervals through tubing,
most likely occurred behind casing. Alternatively, the tubing being a barrier between the tool
it could have occurred through a leaking packer, and inflowing oil. This barrier was taken into
as suggested by minor heating in the static account in the simulation. The simulated profile
temperature profile and low noise detected by correlates with porosity.
Fig. 1. Inflow profile and cross-flow behind casing during flow in the short tubing string identified using Fig. 2. HPT and SNL data recorded under static conditions and during production through the short
HPT-SNL data from the long tubing string and temperature simulation. string. Detection of leakage in the long string during the operation of the short string.
Production through the short string also varied sharply during the operation of the short Example 5 (Job ID-13071) Medium-amplitude noise, with frequency up to
Below is an analysis of HPT-SNL data recorded under tubing string due to gas flow into the long one. This case describes a survey conducted in the 30.0 kHz in the interval 3401.5–3408.0 m caused
static conditions and with flow in the short tubing vertical dual string well to determine water by fluid entry in the reservoir through perforation.
string. The above-mentioned communication Four producing zones were reliably identified injection effectiveness and check well integrity Shut in SNL detected no reservoir noise.
between the short and long strings was confirmed within Reservoirs B to D by the noise characteristic issues. The short string is an injector and the According to temperature simulation most of the
by a difference of 570 psig—between pressures of fluid production through fractures and the rock long string is a producer. It was known that water (77.8%) absorbed in the interval 3394.1 –
measured under static conditions and during matrix. SNL data and reservoir porosity correlated whenever injection started in the short string 3406.6 m. 13.8% of total injected water absorbed in
production from the short string—detected in the remarkably well. the production from the long string stoped. the interval 3374.9 – 3377.0 m.
long string. This communication occurred through a Because of the communication between the This indicated communication of short string Production logging recorded under long string
leak in the long tubing string [2]. strings, lower perforations flowed during the with long string. This objective was achieved by flowing and short string injection. PLT showed
operation of the short string, and the upper the integration of high-precision temperature, both upward and downward flow at the leak
The flowing temperature in Zone C (Fig. 2) was perforations flowed (although not to the same spinner, multiphase capacitance and salinity, depth. Total upward flow rate was 50.9 BPD. Total
reduced by fluid flow into the tubular annulus extent) during the operation of the long one. and spectral noise logging techniques. downward flow rate was 325.2 BPD.
through perforations behind the long tubing string. This significantly reduced the quality of the well’s Recorded temperature, noise and PLT showed
This inflow probably contained gas that cooled production. leak in the long string at 3343.0m.
the fluid moving up the long string. Part of this gas Metal loss from the long string could be
entered the long string through the leak. In Zone D determined by Multi Barrier Imaging (MBI).
(Fig. 2), the flowing temperature and capacitance
Fig. 1. Logging data integration to determine injection efficiency and integrity issues.
Fig. 1. Inflow profile constructed by PLT-based temperature simulation and SNL. (Uninformative ESP
noise was removed from SNL data using a median filter).
Example 1 (Job ID-12028) HPT data analysis showed that fluid flowed in through the C4-C7upper perforated interval. inflow geometry. It was found that fluid from
The survey described in this example was non-uniformly through the perforated section— SNL data acquired under inflow conditions were the C5 unit flowed behind the casing or through
performed in a vertical well producing from the mainly from the lower interval C8—and flowing affected by an operating ESP. The intensity of the near-wellbore zone, entering the wellbore
C carbonate reservoir. The well was equipped temperature simulations for this well indicated noise recorded by the SNL tool increased as it through the lower perforated interval.
with an ESP. The main objective of the survey was that C8 accounted for 72% of the total flow rate. approached the ESP. A median filter was applied
to determine whether water encroachment in Importantly, the static temperature decreased in drift mode to extract the reservoir signal The lack of increase in noise intensity within the
this well was caused by bottom water coning or in comparison with the geothermal profile from the noise and minimise the effect of ESP C8 reservoir was probably due to its high degree
injected water breaking through the producing throughout the perforated interval of the C operation on SNL readings. As a result, the C4- of fracturing. Consequently, low-frequency low-
reservoir. At the time of the survey, the water formation, indicating breakthrough of cold C7reservoir units were identified as the main amplitude noise in this interval could have been
cut was 92% and the total flow rate was 3,433 injected water into the well (Fig. 1). producing zones, with the most intense noise masked by ESP noise.
BPD. The well was surveyed by integrated high- detected in the C5 unit.
precision temperature, spinner and spectral According to the PLT survey, 94% of the fluid
noise logging (HPT-PLT-SNL). entered the wellbore through the C8 lower The correlation of production profiles based
perforated interval and the remaining 6% on HPT-PLT-SNL data allowed analysis of the
Example 2 (Job ID-11021) in non-uniformly through the perforated SNL conducted under inflow conditions was flow. Interestingly, open-hole data from this
The survey described in this example was section—mainly from the lower interval affected by an operating ESP. The ESP generated recently drilled well indicated high water
performed in a vertical high water cut producer B7—and flowing temperature simulations additional low-frequency noise within the entire content within C1–C4. It would therefore
developing the B carbonate reservoir. The for this well indicated that B7 accounted for SNL interval. However, low-frequency noises be logical to suppose that formation water
well was equipped with an ESP. 67% of the total flow rate. The temperature generated by fluid flows in the reservoir differed breakthrough occurred in these reservoir
The main objective of the survey was to within the perforated reservoirs exceeded the from the background noise generated by the units. The increased noise amplitude detected
determine whether water encroachment in temperature that would have resulted from ESP. A detailed analysis of the low-frequency after opening the well indicated behind-casing
this well was caused by bottom water coning or the average temperature gradient in a sump, noise component by data filtration located communication. Thus, it can also be assumed
injected water breaking through the producing and this suggests that water in the produced flow intervals, and a logarithmic representation that it is water from the C1–C4 interval that
reservoir. At the time of the survey, the water fluid was mainly hot formation water (Fig. 1). of SNL data illustrated them more clearly. The entered the perforations. It should be noted
cut was 61% and the total flow rate was 4,630 The PLT survey failed to measure flow rates Flowing SNL panel shows the results of wavelet that the salinity curve indicated water within
BPD. The well was surveyed by integrated high- within perforated reservoirs, because the averaging of input data and clearly separates the lower perforated interval B7–C1. This is in
precision temperature, spinner and spectral spinner was clogged with paraffin hydrocarbons. 0.5–1 kHz noise generated by the ESP from local line with the hypothesis that water approached
noise logging (HPT-PLT-SNL). 0.1–0.4 kHz noises generated by reservoir fluids the perforations from below and then entered the
For this reason, the production profile was flowing through perforations. wellbore through the lower perforated interval.
An HPT data analysis showed that fluid flowed constructed using only SNL and temperature The salinity above the top of the B7 reservoir unit
logging data. was zero, which indicated that the hydrocarbon
Below the perforations, 1–5.5 kHz noise was concentration in the wellbore was higher and that
detected within the C1–C4 reservoir units the water was mainly produced from below.
under both static and flowing conditions. The The recommendation generated for this well
static and flowing temperature curves merged was to repair the cement sheath and shut-off
within the C1–C4 interval and their shape water production from the C1–C4 reservoir
suggested the presence of constant lateral interval.
with SNL data. Signals of different amplitude in a one indicated no flow from Unit A1 and showed
wide frequency range were captured within the another flow zone in A5. Application of PLT
inflow zones. The low-frequency component of technique enabled precise identification of the
the captured noise signals is associated with the ICDs through which the produced fluid entering
ingress of fluid into ICDs, while the high-frequency the liner. According to the logging suite data, it
component is associated with the formation fluid could be concluded that ICD#2, ICD#3, ICD#4, ICD#5,
flow through the rock matrix. and ICD#9 are flowing even though ICD #1 to #5
were closed prior to the logging run.
ICDs from #1 to #5 were closed prior to the repeat Using this well as an example, we could conclude
run that included PLT measurements in addition that application of HPT-SNL technique will assist
to the HPT-SNL suite. Based on the processed HPT- in identification of flow patterns behind the
SNL data, some temperature variations and noise liner, and addition of PLT to the logging suite will
signals associated with formation fluid inflow were provide additional information to locate the zones
identified. The inflow profile was constructed where inflows occur directly into the wellbore, i.e.
using temperature simulation technique. In to determine current status of the (Inflow Control
comparison with the previous survey (run #1), this Devices) ICD’s.
Fig. 1. HPT, SNL, and PLT logs recorded in the reservoir zonе.
also by the top, cased section of the reservoir, that this was a low-sweep zone, and it could
where transient temperature curves indicated be supposed that mainly oil was produced
downward cross-flow. PNN logging showed from its upper portion.
Example 2 (Job ID-11036) The tool was in direct contact with the
This case presents a horizontal dual-string inflowing oil. Noise and spinner logging yielded
oil well selectively producing from different identical results indicating that the production
portions of Reservoir D through long and was from several thin streaks, mainly from
short tubing. Flow-rate metering (PLT), high the shallow Zone 1 of the D4 reservoir unit
precision temperature (HPT) logging and located in the open-hole section. Four more
spectral noise logging (SNL) performed in this thin flowing streaks were located below Zone
well determined the inflow profile for the 1, with the wellbore section below Line A only
horizontal open-hole section of the wellbore slightly contributing to production, which is
below the long tubing string shoe. consistent with the PLT profile (Fig. 1).
Fig. 1. Logging data integration to determine oil sweep efficiency and flow patterns in a screen and
reservoir.
Shut-in spectral noise logging data revealed logging data showing that the zone contains
high-frequency noise behind casing in the virtually untapped amounts of oil.
top portion of the C reservoir (Zone 1). The
signal from this zone features noise streaks, The lower portion of the screen had no flow
probably indicating reservoir fluid flow that either, according to temperature and spinner
was still there after well shut-in. data, and all the fluid from the reservoir
entered the screen above Line A. A deviation of
High-frequency noise streaks detected in gamma-ray values from the initial background
Zone 2 under flowing conditions have been in the lower portion of Zone 2 and in Zone
interpreted as reservoir flows. The spinner 3 indicated scale deposition preventing fluid
and flowing temperature data showed that from entering the screen. In contrast, noise
the sand screen received the maximum data showed major flow in the reservoir
amount of fluid in this zone. within this interval.
Zone 1 was not found by SNL to contain any
fluid flows and is therefore considered a no- It was also found that well production was Fig. 1. Correlation of PLT and SNL data and temperature simulation for the identification of inflow
flow zone. This is in agreement with PNN contributed not only by the target zone but intervals in a horizontal open-hole section.
The flowing temperature was simulated to The fact that noise logging data correlated can be identified by multiphase sensor data and the survey interval. However, the major inflows
accurately locate inflow intervals. The results perfectly with the simulated temperature by pressure gradient change. Also, the coil tubing within the survey interval were found from zone 1
were in agreement with the PLT profile and indicated lateral inflow, normally occurring pressure variance graph shows pressure spikes at and zone 2. The inflow from Unit A16 was coming
additionally identified an inflow interval in in uncased horizontal wells. The frequency of wellhead, which means that static conditions were through fractures identified by low-frequency SNL
Zone 2 that could not be identified by the the noise within the identified inflow intervals unstable. This instability can be seen on SNL logs. signals. The signals in the frequency range 4.3-16.3
spinner due to its threshold limitations. was characteristic of fluid flow through wide kHz observed across Unit A16 indicate production
Notably, the flowing Zone 2 was clearly faults. Fluid inflow zones are distributed uniformly along through both the matrix and fractured zones.
displayed in SNL panel.
Fig. 1. Identification of major injected fluid loss below the survey interval by integrated SNL and
Fig. 1. Reservoir Flow Analysis. Horizontal well. temperature simulation.
that the temperature showed no recovery to- top of the B formation in the lower, unsurveyed
wards the geothermal profile near the bottom portion of the wellbore, flowed laterally and
hole. Intense cooling is clearly seen at the top of caused the cooling observed above the casing
the B formation above a casing shoe. Although shoe (Fig. 2), although no SNL data are available Fig. 1. Construction of an injection profile for a gas injector by integrated use of temperature simulation
no interpreted log data are available for this to support this assumption. and wavelet-filtered SNL data.
interval, data from nearby wells indicate that
the upper portion of the B formation is highly Static and flowing SNL did not detect any noise
permeable. Flowing temperature data showed in the survey interval. Water flow noise was not
that the temperature gradient slightly changed detected in the wellbore because of the ab- Example 5 (Job ID-11018) was not observed to absorb gas, despite its high
in the open-hole section. It was also observed sence of completion components in the survey This case illustrates the application of high- permeability (Fig. 1).
that the temperature during injection became interval that could generate low- precision temperature (HPT) logging and spectral
lower than the static temperature. noise logging (SNL) in locating gas absorption Flowing SNL indicated a number of narrow
frequency noise. Moreover, the injection water zones in the open-hole section of a horizontal streaks with low-frequency, low-intensity noise
According to numerical temperature simula- velocity was too low to create turbulence and well. A temperature simulation showed that caused by gas absorption within Unit A2 and at
tions, 90% of the injected water was absorbed generate noise. SNL also did not detect any wa- despite the homogeneous permeability of the the top of Unit A7, in accordance with simulation
below the tool running depth (Line A) and only ter absorption by reservoirs because each foot open-hole section (except the tight reservoir data. After wavelet filtration, flow zones became
10% within the open-hole survey interval. This of the open-hole survey interval absorbed only units A5–A7), most of the injected gas was clearly visible as 1.6–5.6 kHz noise intervals.
was probably due to the hook-shaped trajecto- 0.1 bbl/d of water, according to the simulation, absorbed at the top of the A formation, with the This noise frequency identified fluid flow through
ry of the well, with the top of the highly perme- and this water flow rate was too low for faults, upper half of Unit A2 receiving 70% of the total faults or fractures. It can therefore be concluded
able B formation being close to the bottom of fractures or the rock matrix to generate any de- injected gas. The remaining 30% of the injected that most of the gas in this well was injected into
the open-hole section of the wellbore (Fig. 1). tectable signal. gas was absorbed below, in the zone extending fractures, which should be taken into account in
An analysis of all available data led to the down to the top of the tight Unit A7. Unit A8 further hydrodynamic modelling. 2.1.6 Multi-well
It can therefore be assumed that only a part of conclusion that most of the injected water was located in the lower portion of the wellbore analysis
the water was absorbed in the surveyed open- absorbed outside the survey interval, most
hole interval; most of it was absorbed at the probably at the top of the B formation.
Example 1 (Job ID-9001, Job ID-10036, by interpreted open-hole data, this zone had
Job ID-10030, Job ID-11023) the highest permeability among all the rocks
Two pay formations – A3 and A5 – are under penetrated by this well. Most of the fluid from
development in this oil field by commingled this reservoir unit flowed into the А5 reservoir
production without multi-string production and a minor portion into the top part of А3.
equipment. Under such conditions, the pressure
in the A3 and A5 reservoirs should be monitored A repeated survey conducted a year later revealed
closely and constantly for efficient field increased water cut. Water inflow was found
development and for the detection of cross-flows mainly in the bottom portion of the А3 reservoir.
that may occur between them. The terrigenous Moreover, cross-flow was observed during
sequence of the oil field is heavily complicated by production. Some of the produced fluid flowed
both lateral and vertical heterogeneity. from the А3 reservoir into А5. This indicates that
the pressure difference between the А3 and А5
An integrated HPT-PLT-SNL survey was conducted reservoirs kept increasing over the last year.
in three wells – WP1, WP2 and WP7. Well WP1
was surveyed twice at a one-year interval. As seen in the map (Fig. 1), WP1 and WP2 are
neighbouring wells with similar conditions: in
WP2 was found to produce mainly from the A3 both of them, the A3 reservoir pressure was
reservoir (Fig. 3). According to the PLT profile, higher than the A5 pressure. The production Fig. 1. Field map.
inflow was mainly confined to the bottom of the well WP7 is located at some distance from
reservoir. However, SNL indicated fluid inflow these wells, and it was also surveyed by HPT-
not only at the bottom but also at the top of the PLT-SNL(Fig. 4). The survey was conducted
A3 reservoir. Inflow from A5 was extremely low. in two steady modes to determine the near-
Under static conditions, borehole cross-flow wellbore zone pressure. According to the
occurred between the top and the bottom of the obtained results, the A5 reservoir pressure
A3 reservoir. This leads to the conclusion that A3 was higher in this well than the А3 pressure.
had a non-uniform reservoir pressure pattern. This is indicated by both pressure calculations
and cross-flow from А5 into А3 detected under
Survey results on Well wp1 are shown in Fig. static conditions and apparently indicates non-
2. As mentioned above, the well was surveyed uniform pressure distribution in the А3 and А5
twice – in 2009 and 2010. According to the reservoirs. In the southern part of the field, the
2009 PLT survey data, reservoir inflows during А3 reservoir pressure was higher than the А5
production were distributed uniformly within pressure, in contrast to its northern part. All
reservoir intervals. However, cross-flows these conclusions indicate the need to optimise
occurred under shut-in conditions from the the reservoir pressure maintenance system.
bottom part of the A3 reservoir. As indicated
Fig. 2. Multiwell Analysis. Well WP-1 data for 2009 and 2010.
Example 1 (Job ID-14231) pressure recorded during HPT survey at the top of A2
This case describes a survey conducted in was 4,007.3 psi, flowing bottom hole pressure was
the deviated well to determine production 3,482.8 psi at the same depth, producing a differential
distribution between perforated intervals and pressure of 524.5 psi. The shut-in pressure value is
to check for communication and fractures if lower than the initial A4 reservoir pressure (4,400
any. This challenging objective was achieved by psi) but higher than the bubble point pressure for A4
the integration of high-precision temperature, (3,062 psi). The flowing pressure value is higher than the
multiphase capacitance and salinity, and spectral bubble point pressure as well.
noise logging techniques. The survey was performed Shut-in temperature showed almost vertical
in three modes: flowing, static and transient. gradient and shut-in SNL captured noise signals
induced most probably by upward cross-flow
To achieve these objectives, High Precision from the zone below the survey interval into
Temperature (HPT) and Spectral Noise Logging perforated interval in A4.
(SNL) surveys were carried out in this well under High frequency (10-30 kHz) signal corresponding
shut-in and flowing conditions. Shut-in bottom hole to the matrix flow was detected within the
Fig. 3. Multiwell Analysis. WP-2.
Fig. 1 Flowing PLT survey. Fullbore spinner data are given in the FBS panel and wellbore pressure in
the PRESS panel. YW is water hold-up from capacitance sensor and SAL is wellbore fluid salinity from Fig. 2 Flowing HPT survey. Flowing temperature TF (solid blue line), simulated flowing temperature
the induction resistivity sensor. Q is the spinner-based flow-rate profile, QZ is the interpreted wellbore TFM (dashed cyan line) and geothermal profile TG (solid green line). The Formation Flow Profile panel
flow profile and QZI is the differential flow profile. (on the right) features the same QZ and QZI profiles as the FBS survey (on the left). The additional QZI
panel is for a zoomed-in view at low inflow rates. The pressure in flowing formation units is shown by
black dashes and the initial hydrostatic pressure by blue dashes.
perforated interval across the major oil inflows holdup values in the sump area under flowing
in intervals Zone 1 and Zone 2. The flowing and and transient conditions indicate that EZSV is not
static temperature profiles did not merge below holding. Flowing temperature and flowing SNL did and X458.9–X459.4 m (A6 unit). Full-bore spin- lower flow rates than the spinner could detect.
the perforated interval, indicating inflow below not show any indication of inflow zone through ner data suggest that production was equally One can pick these zones as temperature gradient
the perforation (LINE A). The different water perforation interval across A2 formation. split between the narrow А2 and А4 perforated anomalies. Whether a given temperature anom-
intervals (Fig. 1). aly is positive or negative depends on a combi-
nation of factors, such as the far-field formation
The temperature logging programme consisted of temperature, inflow rate and the total rate and
one stabilised flowing survey, one transient survey temperature of the upward wellbore flow passing
Example 2 (Job ID-13443) A5 and A6 formation units [27]. The well was after 13 hours and another transient survey after through this zone. This is what TSMp simulator
The well is shown in the example is a slightly surveyed under both flowing and shut-in con- 17 hours of well shut-in. The flowing temperature handles based on the user inputs.
deviated gas-lift oil producer with currently high ditions. The spinner detected production at 53 profile of Fig. 2 provides additional details on the
water cut after eight years of production, with m3/d with a mean water cut of about 70% from inflow profile and shows that the upper flow had For instance, a cooling of 0.9°C at a depth of
three perforated intervals across the A1, A2, A3, two inflow zones: X340.0–X342.2 m (A2 unit) multiple contributing zones, some of them with X460 m would originate from relatively cold but
Fig. 3 Shut-in PLT survey. Fullbore spinner data are given in the FBS panel and wellbore pressure in the Fig. 4 Shut-in HPT survey. Transient temperatures TT1 13 hours after shut-in (solid light green line)
PRESS panel. YW is water hold-up from capacitance sensor and SAL is wellbore fluid salinity from the and TT2 17 hours after shut-in (solid dark green line), simulated shut-in temperatures TTM1 (dashed
induction resistivity sensor. Q is the spinner-based flow-rate profile, QZ is the interpreted wellbore pink line) and TTM2 (dashed purple line) and geothermal profile TG (solid green line). Temperature
flow profile and QZI is the differential flow profile. simulations revealed multiple wellbore cross-flows between formation units. The pressure in flowing
formation units is shown by black dashes and the initial hydrostatic pressure by blue dashes.
strong inflow from the upper part of the A6 unit formation pressures in the X389–X391 m inter-
merging with weaker but warmer upward flow val. bance across perforations (Fig. 3). flowing and shut-in conditions, which is key in
from the lower part of the A6 unit. The overall determining the only correct flow profile and
production profile for this well was estimated Importantly, formation pressure was deter- The shut-in temperature transition logs show formation pressure simultaneously from flow-
with TSMp simulations at 55 m3/d, i.e. very close mined by simultaneous fitting of flowing and a clear response to these zones with a strong ing and shut-in temperature logs. Anyway, this
to spinner readings. shut-in temperatures, and any attempt to indication of upward and downward cross- case provides a learning point to start monitor-
change formation pressure and then compen- flows (Fig. 4). TSMp simulations did not match ing pressure and temperature changes during a
The overall inflow profiles from spinner and tem- sate for this change by varying skin factors the recorded logs very accurately because the transition period after stopping production and
perature data modelling (QZ and QZI in Fig. 2) are would most likely run the matching between cross-flow rate was changing uncontrollably to account for this change in the model. These
the same but the latter resolves more details and either flowing or shut-in temperature logs and during the survey, although the inflow points, data can be recorded at stations, normally above all
picks small inflow zones missed by the spinner. the corresponding modelled profiles. drain points and cross-flow rates were accurate- perforated intervals, when the tool is on standby
ly verified by modelling. It is important to note until the next transient pass.
One can see that formation pressure varied be- The shut-in FBS survey did not reveal any flow, here that the TSMp solver always assumes that
tween different flow units with particularly high although multiphase sensors detected distur formation pressure does not change between In full agreement with the flowing temperature
Fig. 5 Shut-in and flowing inflow profiles produced by temperature modelling. Fig. 1 Flowing PLT survey. Fullbore spinner data are given in the FBS panel and wellbore pressure in
the PRESS panel. YW is water hold-up from capacitance sensor and SAL is wellbore fluid salinity from
the induction resistivity sensor. Q is the spinner-based flow-rate profile, QZ is the interpreted wellbore
logs, shut-in cross-flow had its source at the bot- The downward 3-m3/d flow was absorbed at the flow profile and QZI is the differential flow profile.
tom of the A3 unit, X389–X391 m, with the high- top of the perforations within X458.5–X459 m.
est pressure among all flowing units. This flow To model transient temperature profiles, one
rate is far below the spinner’s threshold, and this has to assume a minor upward flow of about 2.5
explains why it was not captured by a convention- m3/d from A7 to A6 that could not be detect- Example 3 (Job ID-13413)
al PLT survey (Fig. 5). ed by multiphase sensors because it occurred This well is gas-lift oil producer with currently The flowing temperature survey indicated that
behind the casing. This flow pattern is in agree- high water cut after eight years of production, not only A4 but also A5 and A7 contributed
The source inflow then split into upward and ment with the fact that the A6 unit had the low- with three perforated intervals across the A3, to production at 105 m3/d and 0.5 m3/d,
downward flows. Upward 1-m3/d flow met cold- est formation pressure among all units below A4, A5 and A7 formation units [27]. The well respectively, while the fluid loss across A3 was
er 2.5-m3/d inflow from X375–X379 m, which re- X389 m depth. was surveyed under both flowing and shut-in 28 m3/d, confirming that A3 had the lowest
sulted in cooling observed in the transient logs, conditions. The spinner detected production at formation pressure among all flowing units and
then merged with 6.5-m3/d flow from X345 m 89 m3/d with a mean water cut of about 70% even lower than the wellbore flowing pressure.
depth and went up beyond the survey interval. from perforations across the A4 formation, as The temperature survey also suggest that the
well as small 9-m3/d loss of upward flow through main A7 flow came from a very thin layer above
perforations in A3 (Fig. 1). The total flow rate the perforations and then went down towards
above all perforations was 80 m3/d, in good their top where it was detected by a salinity
match with surface tests. sensor.After the well was shut in for 20 hours, a
Fig. 2 Flowing HPT survey. Flowing temperature TF (solid blue line), simulated flowing temperature
TFM (dashed cyan line) and geothermal profile TG (solid green line). The Formation Flow Profile panel Fig. 3 Shut-in PLT survey. Fullbore spinner data are given in the FBS panel and wellbore pressure in the
(on the right) features the same QZ and QZI profiles as the FBS survey (on the left). The additional QZI PRESS panel. YW is water hold-up from capacitance sensor and SAL is wellbore fluid salinity from the
panel is for a zoomed-in view at low inflow rates. The pressure in flowing formation units is shown by induction resistivity sensor. Q is the spinner-based flow-rate profile, QZ is the interpreted wellbore
black dashes and the initial hydrostatic pressure by blue dashes. flow profile and QZI is the differential flow profile.
transient survey was performed and the spinner The difference between upward flow rates from
captured upward 34-m3/d cross-flow from the spinner and temperature surveys was caused
A4 to A3 perforations (Fig. 3). The temperature by varying flow conditions after stopping the
logs (Fig. 4) estimated upward cross-flow at 63 production. The pressure gradually recovered
m3/d and indicated that part of the inflow went and the drawdown pressure in the A4 unit
down at 0.3 m3/d to the A7 perforations and during the temperature survey was twice higher
then channelled up behind the casing to the top than during the spinner survey (Fig. 4).
of the thin A7 layer that was producing under
flowing conditions.
Fig. 4 Shut-in HPT survey. Shut-in temperature TS (solid red line), simulated shut-in temperatures TSM Fig. 5 Shut-in and flowing inflow profiles produced by temperature modelling.
(dashed black line) and geothermal profile TG (solid green line). Temperature simulations revealed
multiple wellbore cross-flows between formation units. The pressure in flowing formation units is
shown by black dashes and the initial hydrostatic pressure by blue dashes.
2.2.2 STEP TEMPERATURE RESPONSE injecting for 1 hour 08 minutes at a rate of 450 75% and 100% the upper part of B was not
TECHNIQUE m3/d. Upon shutting-in the well, four transient contributing to injection. The upper part of B
temperatures were measured (STR technique). turns to injection at a rate of 125%. This regime
Example 1 (Job ID-14160) logging consisting of High Precision Temperature corresponds to the regular regime, which was set
This well is one of the eleven wells selected for (HPT) logging and Spectral Noise Logging (SNL) The flowing HPT – SNL was conducted in 4 injection before the intervention in this well as per injection
acquisition of HPT-SNL data for flow calibration in well were as follows: Estimate effectiveness regimes: 100%, 75%, 50% and 125%. history.
as part of hydrodynamic Micro-Grid Flow of injection in B, Identify possible thief zones
Modelling (MGFM) project for B. It has also above and below B, Check well integrity Static temperature log shows some anomalies The 9-5/8” casing leak at x576.7 m was detected
been selected as a candidate for pressure pulse (Communication between LS & SS) associated with upward cross-flow of a minor at all performed regimes, but it was less
testing (PPT) in Cell 1. The objective of PPT will volume of injection water behind casing to pronounced at maximum rate of 125%. It might
be to determine the dynamic permeability of B HPT (High Precision Temperature) – SNL (Spectral A. The STR (Step temperature response) was refer to C injection performance drop down
formation and check communication between B Noise Logging) technologies were utilised performed in this well to assess injection after injection pressure was increasing. Also, it
and C. during the survey. All the logging operations allocation across B. It confirmed the response was detected the better injection performance
were conducted in the short string when the on temperature flux from B only. It means the of B at rate of 125%. It affects to volume of
The short string was shut-in in October 2010. long string was shut-in. HPT and SNL surveys temperature anomalies on A were not caused behind 9-5/8” casing flow to be less than during
April 27, 2014 injection to the long string was were conducted under flowing, transient and by active injection into these reservoir units. other injection regimes. (see Fig. 1)
stopped and the short string was brought on- static conditions. (see Fig. 1)
line to injection. The average injection prior the According to HPT-SNL survey results, most of
intervention was 5690 BPD. The first HPT-SNL survey was done under shut-in Infectivity test performed at 4 different injection the fluid (90%) was injected into B reservoir. (for
The objectives of the integrated production condition. Afterwards, the short string started rates shows that on regimes with rate 50%, more details see Fig. 2)
Fig. 1. Temperature and SNL measurements in the reservoir zone. Fig. 2 Step Temperature Response Technique.
It should be noted that the injectivity of the C4 estimated by temperature simulation at 3.1% of temperature (with the selected amplitude and The resulting curves are shown in the figures
reservoir unit was low in both 2009 and 2011. the 2009 total injectivity (Fig. 2). The injectivity phase of injection water temperature fed into as dashed pink lines. The modelled flowing
The injection rate in this unit was too low to of the C4 reservoir unit in 2011 was 0.9% of the a simulator) as a dashed blue line. This took temperature is seen to deviate from the
be detected by the full-bore spinner and was total injectivity in Scenario 1 and 1.5% in Scenario 2 into account daily temperature variations. The measured temperature, which affects the
modelled curves are shown in Figs. 3 and 4 as static temperature simulation.
dashed black lines. As seen in the figures, the
modelled flowing and static temperature curves This illustrates the importance of using
based on the correct temperature history correct daily temperature variation data in
correlate with the measured temperature the simulation of flowing and static wellbore
curves. temperatures. Temperature measurements
must always be made at the surface for
The effect of daily variations of injected water at least a day before and during wellbore
temperature on the wellbore temperature measurements, in order to design a proper
profile was analysed by generating and feeding temperature survey. The lack of data on
into the simulator a knowingly incorrect daily temperature variation phases, survey
injection temperature history with a changed schedules and injection volumes otherwise
average temperature and amplitude and renders the injection profile based on
phase of daily temperature variations (Fig. 2). temperature simulations uncertain.
Fig. 2. Effect of fracture on the injected fluid temperature distribution in the reservoir.
Example 2 (Job ID-10050) temperatures and are key input parameters for
This example demonstrates the effect of temperature simulations performed for injection
injection fluid temperature variations on wells.
wellbore temperature in an onshore injection
well under static and flowing conditions. This Temperature measurements at the surface
effect was analysed using the RFI (Radial Flow in were in this case made with a high-resolution
Injectors) temperature simulator. temperature sensor installed on a pipeline near
the well and insulated with a special material. The
Injection fluid temperature is known to be sensor measured injection fluid temperature for
affected by daily and seasonal temperature several days and fed these data into the simulator.
variations. Average annual injection water
temperature and daily and seasonal temperature Fig. 1 shows the measured temperature of
amplitudes and phases impact static and flowing injected water as a red line, and the modelled Fig. 1. Surface temperature variations.
Fig. 1. Construction of current and historical injection profiles by HEX logging and temperature
simulation.
Fig. 1. Effect of LROCK parameter selection on the modelled and measured curves.
Example 1 (Job ID-7001) for one of the injection wells verified these data. conductivity profile LROCK INCORRECT (shown In this way we can see how geothermal
This case illustrates the influence of geothermal in blue in the LROCK panel) was fed into the temperature affects static temperature and that
rock temperature on static temperature in an Figs. 1 and 2 show the reconstructed local simulator. The resultant thermal conductivities static temperature simulations can therefore be
injection well measured four to five days after thermal conductivities of rocks: LROCK of the rocks correspond to the simulated curves used to verify the geothermal profile of the field,
shut-in. This effect was analysed using the RFI CORRECT (a solid black line) and the TGM INCORRECT and TSM INCORRECT. The new as a basis for further temperature modelling.
(Radial Flow in Injectors) temperature simulator. corresponding geothermal curve TGM CORRECT simulated temperature curve, shown in blue,
(a dashed black line). As seen in the figures, the obviously does not match with the measured
One of the wells in this field was studied to simulated static temperature (TSM CORRECT) static temperature.
reconstruct the geothermal profile. The selected correlates with the recorded temperature log,
well was never put on production and was far which indicates the correct selection of all
from other production and injection wells. parameters, including the geothermal profile.
The recorded geothermal profile was used to To demonstrate how geothermal temperature,
determine thermal conductivities for all of the and therefore thermal conductivity, affect static
reservoirs, and temperature simulations performed temperature, the knowingly incorrect thermal
Fig. 1. Inflow profiling and cross-flow detection by spinner and SNL data. Wavelet filtration of SNL data
enabled accurate sizing of flow intervals.
Two scenarios could unfold there: (1) The probabely due to depletion or scale deposition.
spinner could have failed to detect any flow Some fluid from Zone 4 entered the wellbore
from the middle perforations due to its through the lower perforations, most probably
limitations; (2) This perforated section could due to cross-flow in this well section. This
be plugged/damaged and small upflow could should be taken into account when designing
occur from this part of the reservoir behind workovers.
the casing to enter the wellbore through the
upper perforations. The quality of the second On the whole, SNL in a straightforward fashion
perforated interval should be checked by Multi located flow streaks. These streaks correlate
Barrier Imaging (MBI). perfectly with the open-hole permeability profile,
unlike spinner data which was noisy and less
The most interesting observation was on accurate. The comparison of SNL and spinner data
production evaluation for the lower perforated gives an idea about cross-flows in Zones 1 and 2
section including Zones 3 and 4. According to that should also be taken into account in workover
SNL, a thin streak in Zone 3 was the main source planning, as for Zone 4. In this particular case,
of well production. Open-hole data confirmed re-perforation and stimulation of all perforated
the high permeability of this interval. It should intervals can be recommended, although the
be mentioned that this was the only streak obtained results suggest that selective re-
that produced fluid mainly through the matrix. perforation of the middle perforations would
The fact that spinner indicated a much thicker bring little reward due to poor cement quality
production interval in Zones 3 and 4 means behind the casing and that good cement should
that the quality of the bottom perforations thus be restored first. Fig. 1. Identification of water breakthrough from a nearby injection well and upward cross-flow behind
was goodbut the reservoir was inactive, most casing by integrated PLT, SNL and temperature simulation.
from the perforated interval X254–X269 mbdf indicated fracturing and injection into fractures,
Example 2 (Job ID-11014) High-amplitude noise was detected in a wide into the B2 reservoir unit. This low-frequency as detected by SNL.
This well was drilled as a water injector for the frequency range, 9–19 kHz, within the interval noise is characteristic of flow through a
B and C reservoirs separated by the C1 seal. X280.0–X285.0 mbdf. Noises detected during fracture. A median filter was applied in drift mode to
Analysis of PLT-HPT-SNL data clearly showed shut-in and injection had equal amplitudes extract low-amplitude noise. As a result, it
flows in the receiving intervals X253.9–X264.5 and frequencies. Moreover, the static and The static temperature curve TSM was simulated became apparent that small amounts of fluid
mbdf in reservoir B and X276.3–X279.4 mbdf in flowing temperature curves TS and TF merged to determine the injection profile using the were injected into the B2 reservoir unit through
reservoir C. into a curve with a temperature lower than matrix injection model. The deviation of the the rock matrix and into the B3 unit.
geothermal below a depth of X285.0 mbdf. TSM curve from the static temperature curve
SNL enables differentiation between matrix These facts all indicate lateral flow in the well
and fracture injections. Low-frequency noise area and suggest that this cooling was caused
detected by SNL indicated that injection was by water breakthrough from a nearby injector
mainly into fractures, while injection within (Fig. 1).
the narrow interval X279.9–X282.0 mbdf of
the C4 reservoir unit occurred into the matrix. A temperature drop and low-frequency noise
This correlates with the open-hole permeability were detected above the perforations, which
profile. indicated upward cross-flow behind casing
Example 3 (Job ID-10025) jected water was recorded in early January. Ac-
This case illustrates the application of integrat- cording to the well history, the highest injection
ed high-precision temperature (HPT) logging, rate was recorded in winter at 230–240 m3/d
Spectral Noise Logging (SNL) and spinner log- (Fig. 1). At that time, intense injection created
ging (PLT) for constructing historical and current a reservoir cooling anomaly. Then warm water
injection profiles and detecting cross-flows be- entered the well, in smaller amounts than in
hind casing in an onshore injection well. winter, and created local heated zones within
the general cooling anomaly.
Flowing PLT data identified two narrow perforat-
ed flow intervals (Fig. 2). Temperature and noise The results of the static temperature simulation
surveys were conducted to determine the geom- were confirmed by flowing SNL. The high-am-
etry of injection fluid flow in the reservoir. The plitude in Zone 1 was generated by intense wa-
static temperature curve showed major cooling ter filtration through the reservoir rock matrix.
relative to the geothermal profile within and However, the simulated profile indicated a rela-
above the perforations. The temperature curve tively small volume of injected fluid in this interval,
has two characteristic cooling peaks. However, a which in turn suggested that injection here started
static temperature simulation located the point recently and is now at its most intense.
of maximum water injection not at the point of
the maximum cooling, as could be expected, but Noise with a frequency of less than 5 kHz de-
in the heated intervals of Zone 2 within a cooling tected in Zone 2 is characteristic of water flow
background anomaly. This was due to seasonal through fractures. The low-frequency 2.5-kHz Fig. 2. Detection of cross-flow behind casing by SNL and temperature simulation.
variations of the injection fluid temperature. component of the noise signal in this zone was
This injection well was surveyed in April, while produced by fluid flow behind casing from the
the minimum annual temperature of the in- perforated interval to Zone 1. In Zone 3, SNL detected low-frequency noise lower than 2 kHz reservoir units of Zones 1 and 2, thus bypass-
generated by the filtration of the injected water ing the target reservoir. Interestingly, open-hole
through the perforated interval. Low-amplitude gamma-ray readings increased across the target
5.6–7.9-kHz noise was produced by low water reservoir. It can be assumed that the increased
filtration through the rock matrix. open-hole gamma-ray readings in the perforat-
Importantly, the static temperature simulation ed reservoir interval of Zone 3 were due to the
showed that the injected fluid flowed up the deposition of radioactive salts in the near-well-
casing annulus into the overlying, unperforated bore zone that probably clogged this interval.
B4–C1 interval. Static noise logging detected Some fluid entered the wellbore through a by fluid flow behind casing within this interval It was found that the main flow units were
intense noise in fluid flow intervals. casing leak within Reservoir C1, and the rest of rather than by water encroachment. represented by the upper one and those below
it was channelled up into a perforated interval the perforations.
Shut-in spinner logging identified downward of Reservoir B9. A large difference between Spectral noise logging ensured the clearest
wellbore cross-flow from a perforated interval the flowing and static temperatures at the very identification of flow intervals, as seen in the Inflows through the perforations within Reservoirs
of Reservoir B4 to Reservoirs B6, B7 and B9 bottom of the survey interval indicated inflow SNL_SHUT-IN and SNL_FLOWING panels of Fig. B3–B8 were mainly caused by cross-flows behind the
through perforations and to Reservoir C1, from below it. 1. As mentioned above, noise detected under casing and through fractures from the overlying and
possibly through a casing leak. This cross-flow shut-in conditions was most likely generated underlying formations. Thus, none of the perforated
was caused by unscheduled gas bleed-off less The spinner survey failed to measure flow rates by gas bleed-off, as indicated by similar noise reservoirs under development contributed to the well
than a day before the survey. As a result, the within the perforated reservoirs because of patterns under shut-in and flowing conditions. production. The principal recommendation would
temperature distribution in the zone of interest their instability. The high noise amplitude revealed a large therefore be to stimulate and re-perforate Reservoirs
could not be accurately assessed. fraction of gas in the well production due to a B1–B8.
Sigma logging data were used to identify pressure drop below the bubble point pressure.
Flowing high-precision temperature logging breakthroughs of saline formation water and
detected fluid inflow from both perforated and characterise residual oil saturation. Increased
unperforated intervals. Flowing temperature salinity and water-oil displacement were found
simulations showed that 45% of the fluid was in Reservoirs B9 and C1. The slightly increased
produced from the unperforated Reservoir C1. salinity in Reservoirs B3–B8 was most likely caused Example 5 (Job ID-11051) upper portion of the A2 reservoir. Some fluid
This well, producing from the A reservoir, was entered the perforations behind the casing
surveyed by high-precision temperature (HPT) from above. Ideally for this scenario, Multi
logging and spinner logging (PLT) to construct Barrier Imaging (MBI) should be performed to
behind-casing and wellbore inflow profiles. The determine the quality of the lower perforations.
survey objective was to identify the source of The poor performance of the upper and lower
water encroachment [25]. perforations could also be due to clogging
with heavy hydrocarbons. High-frequency
PLT data indicated that inflow occurred mainly noise within the A2 interval indicated that the
from the middle of the perforated A2 interval. fluid flowed mainly through the rock matrix,
Salinity and water holdup sharply decreased in although some fracture noise was also
this interval because of inflow gas. The presence detected within the flowing perforations. In
of gas was also indicated by high-amplitude addition, the noise logging tool detected low-
noise, as the production pressure was lower frequency noise reaching the perforations
than the bubble-point pressure. It should be from the water-saturated portion of the A4
noted that the salinity and water holdup data reservoir below, probably because of upward
identified some fluid inflow through the middle cross-flow behind casing.
perforations that was too low to be detected by Thus, an integrated analysis of available
the flow meter (Fig. 1). data delivered the conclusion that water
encroachment was caused by cross-flow behind
Noise logging showed that the fluid flowed casing from the A4 reservoir.
behind casing both in the middle and in the
Fig. 1. Flow detection in unperforated reservoir intervals by HPT, PLT, Sigma and SNL.
Fig. 1. Detection of fluid channelling behind casing by HPT, PLT, Sigma and SNL.
Fig. 1. Identification of upward cross-flow as a source of increased water cut by SNL and multiphase
analysis.
duction under flowing conditions came from also evidenced by Sigma logging data indicat-
below the leaking packer. ing that Reservoir C1 of the spinner-detect-
Example 6 (Job ID-10049) Static spectral noise logging detected no ed Zone 1 was flooded during the survey, as
This case provides a good example of how noise generated by producing reservoirs or Spectral noise logging identified a flow zone, shown in blue in the LITHOLOGY column of
integrated high-precision temperature (HPT) fluid cross-flows between them. This indi- Zone 2, within a perforated reservoir sec- Fig. 1.
logging, spectral noise logging (SNL), PLT cated that the positive static temperature tion. Fig. 1 shows that noise was also pres- Fluid flow behind casing from the upper un-
spinner logging and Sigma logging can be anomaly observed within the perforated in- ent below the survey interval. Interestingly, perforated reservoirs A and B entered the
effectively used to detect fluid flow behind terval could be caused by bottom water rise numerous fluid flow zones were found in the wellbore through the upper perforation was
casing, flowing through leaking cement, and but not by transient wellbore conditions. producing reservoirs A and B above the perfo- clearly illustrated in the transient tempera-
entering the wellbore through a perforated This assumption was later confirmed by rated interval. ture logs: the temperature within the perfo-
interval. Initially, the well produced from the PNN logging data interpretation, as seen in rated section was lower than both flowing
bottom of Reservoir C. After 10 years of well the volumetric model (LITHOLOGY) column Spinner logging indicated two inflow zones and static temperatures because of fluid in-
operation, the upper portion of Reservoir C of Fig. 1. across perforations. The upper inflow Zone flow from the upper, colder strata.
(C1 unit) was also put into production and 1, occurring in the top portion of the perfo- It should be noted that SNL data correlated
the lower interval was isolated with a cement The difference between the static and flowing rated interval, yielded most oil. Most proba- remarkably well with porosity, which as a re-
plug. The well was surveyed to assess its in- temperatures below the perforated interval bly, oil from the upper producing reservoirs sult can be used to identify narrow flow units
tegity and the current condition of producing was indicative of inflow from below a cement A and B entered the wellbore behind the cas- of dolomite omitted in the open-hole data in-
formations (Fig. 1). packer, and therefore of its leakage. Spinner ing through the upper perforations. This is terpretation.
logging showed that 65.6% of the well pro-
Example 7 (Job ID-14402) through the perforated interval is not uniform, 2.4 LATERAL FLOW IDENTIFICATION entered D2: high-amplitude noise was detected
The main objectives of the survey on the given the bulk of the fluid supplied to the lower part during injection in a wide frequency range of
producer well, were to check communication of the interval. Example 1 (Job ID-11072) 2–16.5 kHz and the static temperature curve
behind casing and quantify the flow distribution In this well, injection into the D2 and E1 reservoirs, showed a cooling peak in this reservoir (Fig.
across the logged interval. According to the methods of composition there was surveyed by high-precision temperature 1). Static SNL detected the same 0.8–16.5 kHz
are no changes in values below perforated (HPT) logging, spinner logging (PLT) and Spectral noise in the D2 reservoir as during injection.
HPT (High Precision Temperature) – SNL (Spectral interval on shut-in and flowing conditions, Noise Logging to construct the injection profile It is assumed that this reservoir flowed after
Noise Logging) technologies were utilised indicating the absence of the inflow into the and detect cross-flows behind casing and bottom- injection, as confirmed by the pressure
during the survey. HPT and SNL surveys were wellbore below perforation. However, the hole leaks. The static temperature log showed behaviour: the static pressure at the top of the
conducted under flowing and static conditions. temperature curves recorded on shut-in and cooling caused by cold fluid injection within the D2 reservoir three days after shut-in was 8.29
The first HPT-SNL survey was done under shut- flowing conditions did not merge in the sump, perforated D2 and E1 reservoirs. MPa, exceeding the initial reservoir pressure by
in condition. Well was shut-in 3 days before the and signals with frequency 13.0 kHz were 2.93 MPa. A differential pressure of 10.06 MP, at
survey. After that the well was flowing 12 hours detected on SNL FLOWING panel opposite The most intense flow of the injected water which the well operated, was apparently off the
and second HPT-SNL survey was performed. reservoir A3, indicating the inflow from given through perforations was detected by PLT data optimum range. In such a case, the well should
formation. and a flowing temperature break within D2. be shut-in for a long period of up to a month
Heating anomaly on temperature curve so that the reservoir pressure in the well area
recording under flowing condition and high In this way, the fluid flows from the reservoir The reservoir-oriented static temperature could fall off, and then put in injection mode at
amplitude noise in a wide frequency spectrum A3 and moves upward behind casing channeling logging and Spectral Noise Logging techniques lower differential pressure.
indicate inflow of fluid from the formation of and mixing with the fluid received from the also indicated that the injected fluid mainly Injection flow into the E1 reservoir was detected
A1 and entering into the wellbore through the reservoir A1 and exit into the wellbore through
perforated interval. Moreover, the fluid inflow the perforated interval.
Fig. 1. Location of injection intervals and lateral fluid flows under static conditions by SNL.
Fig. 1. Channeling Identification.
by 2–5.6 kHz noise and a characteristic injection no deposit was found at the bottom hole, as ture (SHPT), Sigma and spectral noise logging COLUMN in Fig. 1). Moreover, В5 also features
temperature break. The use of a median filter indicated by the static salinity curve, suggest (SNL). high GR values suggesting saline reservoir water
for SNL in drift mode clearly identified injection that some injected fluid was lost below the flow. Other reservoir units, occurring above the
intervals, in particular the one in the E1 reservoir survey interval. However, the calculated PLT In Fig. 1, the geothermal profile is shown in production zone, were apparently unaffected
that was indistinct in raw SNL data. profile (middle column) showed no fluid flow green and measured temperature in red. A pos- by production processes.
below a depth of X254 m. Therefore, the fluid itive measured temperature anomaly detected
The facts that the static and flowing temperatures flowed into the E1 reservoir and below the in the В5 reservoir interval was caused by lateral All the above data were taken into account to
did not merge in the survey interval and that survey interval at a rate that was too low to be flow. High-frequency noise detected by SNL was produce recommendations to sidetrack the
detected by the flow meter. also generated by intense fluid flow through the upper portion of the B10 reservoir and perforate
rock matrix in this zone. the B6 and B7 reservoir units. The B5 reservoir
was considered unpromising for production in
According to Sigma data, the В5 reservoir this zone.
contained a high-salinity fluid. The sweep profile
Example 2 (Job ID-10026) geometry and current oil saturation, and to is shown in blue in a volumetric model (VOL
The deviated well WP-6 was drilled to bottom at provide recommendations on additional perfo-
the C reservoir sequence in November 1976. In ration. This objective was successfully achieved
2006, it was shut-in because of high water cut. with integrated static high precision tempera-
The well was surveyed to determine the flow
Fig. 1. Geothermal profile of the field, flow geometry and current oil saturation according to
integrated HPT-PNN-SNL data.
Fig. 1. A static survey of the entire well. Fig. 2. A static survey of the reservoir interval.
Fig. 2. 3D view.
pressure in each reservoir zone was assumed to be that communication with BP15 is created by fracture,
Example 2 (Job ID-13022) equal to wellbore pressure after three days of shut- most probably induced during the frac jobs.
This is the vertical producer with hydro-frac SND flowing shows reservoir noise across in. The temperature logs at P1 were recorded both in
completion. The frac water was flushed back in permeable zones (see Zone 3 at Fig. 2). Some low- quasi-stationary flow regime (blue log at Fig. 2) and The cooling anomaly of shut-in temperature SHUT-
a few days but the water cut sustained at 80 % frequency noises typical for fluid flows through shut-in temperature logging regime (red log at Fig. 2). IN (as against TG) suggests that hydraulic facture
[26]. The HPT-SNL-PLT survey was performed two hydraulic fractures and/or a cement sheath initially extended all the way down to the E-line,
months after completion of the frac job. The well channel were captured both above and below The simulation results are shown on the FORMATION but the flowing temperature and SNL suggest that
was flowing at a constant rate the entire time and perforations (see Zone 3 on LFD FLOWING Panel at FLOW PROFILE panel at Figure 2. They suggest that the bottom part of the fracture is currently closed
the survey was started with flowing passes. The Fig. 2) in the interval from Line A down to Zone 3. perforations are connected to both overlying and and the inflow starts from D-line. The temperature
well was then shut in and the shut-in pass was underlying reservoirs. The underlying reservoir simulations (dash line TFM) provide a good match to
recorded after three days (see Fig 1.). Termosim numeric flow modelling was performed BP161-2 contributes to production from perforations the scenario in which all the water cross perforations
based on SNL flowing units and allowed more with oil. The overlying formation BP15 contributes to arrive from the overlying BP15 formation.
The PLT interpretation (mechanical spinner and insight into the flow geometry behind casing at production from perforations with water.
multiphase sensors) suggests that the main oil reservoir level. One can also note a packer noise across the A-line,
inflow to the wellbore occurs from the bottom part Combined noise and temperature analysis suggest which is created by flow turbulence.
of the perforated zone while water is coming from The geothermal profile TG (green log at Fig. 2)
the middle part (see BOREHOLE FLOW PROFLE at was reconstructed using reverse modelling from the
Fig. 2). The total water cut is estimated as 15%. three well shut-in surveys (see Appendix A). Reservoir
Fig. 1 HPT-SNL-PLT logging procedure. Fig. 2 PLT (to the left) and HPT-SNL (to the right) interpretation of borehole and formation inflow.
Fig. 2 НРТ-SNL-PLT survey results with subsequent temperature simulation showing inflow profile in
the wellbore and behind casing.
minor water contribution from all frac sleeves (see connected to two reservoir fractures.
BOREHOLE FLOW PROFILE at Fig. 2).
Termosim numerical flow modelling used the SND
SND flowing shows reservoir noise across flow zones and ended up with the FORMATION
permeable zones (see Zone 1 to 6 at Fig. 2). High FLOW PROFILE panel at Fig. 2. It suggests two
frequency SND panel has picked up the flow water sources: most of the water (140 m3/d) is
through the frac sleeves and the flow behind the coming from below the survey interval at 4348 m
liner. The connection between reservoir noise and some minor water inflow 10 m3/d is expected
across Zone 1 and frac sleeve #3 is a clear indication from the bottom fracture of Zone 6.
that the packer at 3740 m is not holding. The
SND/LFD panel also suggests that frac sleeve#1 is
There is a cooling anomaly confined to formation Based on the survey results, the remedial
fracs picked up by SNL at 3840 m, which is a workover was carried out and cement was
clear indication of induced frac communication squeezed through the frac sleeve #3 into the
with overlying BP15 formation. zone between the two packers, which resulted
in complete water shut-off.
Example 5 (Job ID-11058) tive of locating its flowing intervals. This objec-
This case presents a slanted dual-string well se- tive was achieved by integrated high-precision
lectively producing from the A and B reservoirs temperature and spectral noise logging (HPT-
through long and short tubing respectively, and SNL) [25].
Fig. 1 HPT-SNL logging procedure. focuses on the lower reservoir B with the objec- An inflow profile for the B reservoir was con-
Fig. 1. Identification of inflow intervals by temperature simulations for both perforated and unperforated
intervals. SNL data detected gas inflow caused by pressure decrease to below the bubble point.
structed by the simulation of flowing tempera- SNL located flowing reservoir intervals in agree-
ture for the long string. The advantage of tem- ment with the temperature-based production
perature simulations for inflow profiling is the profile. Noise amplitudes in Zone 1 and Zone 2 in-
possibility to identify flowing zones in the reser- dicated large amounts of gas in the reservoir due
voir, including those outside the perforated in- to low pressure in the operating well, which was
tervals. This was confirmed by the construction below the bubble point pressure. According to the
of the QZI* profile that had no unperforated SNL noise frequency distribution, fluid flowed in
but flowing reservoir intervals. The simulated the reservoir through fractures, while the maxi-
temperature TFM* corresponding to the QZI* mum noise amplitudes were within a frequency
profile is seen to substantially deviate from the range of 3–6 kHz. In Zone 3, SNL detected only low
measured curve due to flow outside the perfo- noise, possibly due to the small amount of gas or
rations (Fig. 1). low flow rate.
Fig. 1. Identification of a water breakthrough interval and the main fluid inflow interval by temperature
simulation and spinner logging.
The current inflow profile was constructed to indicate because of the spinner sensitivity came from the perforated interval of A3 and A4. pacitance sensors included in the integrated
using the flow temperature simulator. The threshold. The temperature simulation showed In combination with low reservoir pressure, this HPT logging.
inflow profile was in good agreement with that only half of the total amount of oil was was the reason why the well stopped flowing
the PLT profile above the SSD but indicated produced from the E reservoir and the other naturally through the short tubing string. The source of increased water cut from the A5
that fluid entered the wellbore also from the half from the D reservoir that was supposedly formation was the upward shift of the OWC.
E5-E7 reservoirs, which the PLT survey failed suspended from production. Long tubing string Different temperatures and temperature gradi-
Temperature and Spectral Noise Logging data ents recorded during shut-in and flowing passes
indicated that fluid inflow mainly occurred from below the perforated interval of A5 i.e. in Zone
the perforated interval of the A5 reservoir, i.e. 3, indicated formation water coning, possibly in-
Zone 2. Wellbore inflow was also detected in cluding flow behind casing.
Example 7 (Job ID-13054) Specific to this survey, the pressure drawdown the perforated interval by the salinity and ca-
Well OP-1 was drilled and put into operation on the top of A5 reservoir in quasi-stationary in-
in September 2006. It was completed as a dual flow mode was as low as 33 psi relative to the
string naturally flowing production well with baseline measurement made two days after
separation packers. The short string produced well was shut-in. Another specific feature was
from the A3 and A4 reservoirs and the long the detection of low-amplitude acoustic noise
string from A5. used to confirm the results of integrated HPT-
The total fluid production rate from A3 and A4 SNL and identify reservoir flow intervals.
was 1000–1200 BPD. After two years of opera-
tion, water cut for SS from A3 and A4 increased For the given downhole conditions, the inte-
to 12%. During the same period, wellhead pres- grated survey revealed the following:
sure dropped so much that natural flow of the
well ceased. To help resume flowing through SS No leaks in completion components or down-
swabbing was carried out but without success. hole equipment and no communication be-
Since 2008, SS has been out of operation. tween tubing strings were found over the sur-
vey interval.
The total fluid production rate from the A5 res-
ervoir through LS was 1500 BPD. In September Short tubing string
2012, reservoir A5 water cut was 60%. When the Upward cross-flow between the perforated in-
survey commenced, the well was naturally flow- terval of the А3 reservoir and the top part of
ing through LS. the perforated interval of A4 was found in Zone
1. This cross-flow is indicated by near-zero tem-
The survey was conducted to identify the source perature gradient in the Shut-in, Transient 1,
of increased water cut and cross-flows behind Transient 2 and Transient 3 logs and by acoustic
casing above and below perforated intervals, and noise which was detected in this zone by SNL. It is
to assess integrity of completion components and highly probable that this cross-flow entered the
downhole equipment. The integrated HPT-SNL A annulus between the packers. The potential
technique was employed to reach all these ob- flow path is impossible to trace accurately be-
jectives. The survey was conducted during inflow cause of LS tubing wall. The source of increased
through LS during a short stop and as a baseline water cut from A3 and A4 is impossible to iden-
measurement made two days after well was shut- tify reliably without putting the well under the
in. inflow regime through the short string. Howev- Fig. 1. Water Breakthrough Identification in Dual string completions well.
er, it can be assumed that high water-cut fluid
Fig. 4. Layer pressure calculated using TSNL data (black vertical line in the “Pressure” column).
Fig. 6a. Reservoir pressure calculation for Layer 2 (Pe1 = 3,598 psi).
Pressures in these flow units, Layers 2 and 3, layer were 12–31 psi lower than pressures
have been calculated to be 3,598 psi and 3,617 determined by an RFT survey (shown as red
psi, respectively, as shown by dashed lines in circles in the “Pressure” column Fig. 4), probably
the “Pressure” column of Fig. 4 and in Table due to production from perforated zones in Fig. 6b. Reservoir pressure calculation for Layer 3 (Pe2 = 3,617 psi).
2. The reservoir pressures estimated for each nearby producers.
2
2 3,598.0 3,611
3
4 3 3,617.0 3,648
Example 2 (Job ID-10047) sharply reduced noise corresponded to flowing the reservoir was cooled at the bottom but was into account in dynamic modelling. The results
This case presents a classic example of injection perforations detected by spinner data. not under injection during the survey, according of the survey suggest the following actions: (1)
into fractures (Figs. 1). This well injected water to SNL data. Therefore, this cooling was possibly The lower perforations can be reperforated and
into two perforated intervals in Zones A–C. One of Thus, in this intricate case, when the SNL signal is caused by injection in the well vicinity or by in- stimulated, 2) Sidetracking is recommended to
the objectives of the survey performed in the well strongly masked by wellbore flow, a signal com- jected water from offset injectors. increase injection into the rock matrix in this
was to construct the current injection profile for ponent generated by injection into the reservoir zone because of fracture flow and channelling
these zones. The integrated survey consisted of through a fracture must be extracted from the The fact that injection around this injector oc- across the upper perforation.
spinner logging, high-precision temperature (HPT) overall signal. After wavelet filtration, SNL data curred mainly into fractures should be taken
logging and Spectral Noise Logging. clearly showed two injection zones correlating
with the spinner-detected ones (Fig. 1).
Spinner data showed that all injected water left
the wellbore through two narrow zones in the Temperature logs recorded under static and
upper perforations, with a 30–40-ft no-flow sec- flowing conditions clearly detected two frac-
tion between them. No water was found to flow tures across the upper perforations and no cur-
through the lower perforations. SNL detected rent injection into the reservoir across the bot-
only low-frequency noise throughout the sur- tom perforations, as both the flowing and static
vey interval and no medium- or high-frequen- logs merged below Line A. The shape of the stat-
cy noise characteristic of injection into the rock ic temperature profile indicated two intervals of
matrix. This low-frequency noise was generat- uniformly distributed injection into fractures
ed by turbulent flow in the wellbore. Zones of (Figs. 1 and 2). It should be noted that
Fig. 1. Correlation of static and flowing temperature anomalies with SNL data.
Fig. 2. Casing corrosion identified by MBI.
meant lateral fluid flow through permeable substantial loss of metal from casing at a depth
reservoir units. These anomalies were most of X2. Gas entered the casing annulus through
likely generated by local processes in this this leak and flowed through cement fractures Example 2 (Job ID-13055) The warming anomaly on temperature curve
particular well, since no similar anomalies were into porous rocks. This flow pattern is evidenced The main objectives of the survey on the given in flowing mode and high amplitude noise in
observed in nearby wells at the same depth. by the shape of the flowing temperature curve producer well, were to evaluate the quality wide frequency spectrum across the perforated
and by noise typical of fluid flow through the of the perforation job and determination of interval in A8 formation indicate fluid inflow
During compressor operation, some casing annulus (Zone 1). High-frequency noise corrosion intervals on 7” production casing and into wellbore through perforated interval. The
temperature anomalies were also observed in that appeared in Zone 2 indicated fluid filtration 3 ½” tubing. MBI data characterises the perforated interval
Zone 1. A cooling anomaly at a depth of X1 was through the rock matrix. as an equivalent metal loss area, which confirms
caused by injected gas that broke through a HPT (High Precision Temperature) – SNL (Spectral satisfactory quality of perforations.
gas-lift valve. At the same depth, SNL detected The detected casing leak was isolated, and the Noise Logging) – Multi Barrier Imaging (MBI)
2.5–30 kHz noise generated by turbulent gas resulting watercut decreased. technologies were utilised during the survey. Above the perforated interval across the A2
flow through the gas-lift valve. MBI indicated HPT and SNL surveys were conducted under formation HPT data shows cooling anomaly
flowing and static conditions. The first HPT- in both regimes (static and flowing) and noise
SNL survey was done under flowing condition. on SNL panel. This anomaly is caused by gas
After that the well was closed and MBI survey inflow into the borehole through 7” casing leak.
was performed. Finally, HPT-SNL measurements Thickness log calculated from MBI data confirms
were taken under static condition. casing leak at the same depth.
and 2011 shut-in temperature logs enabled the 3. Noise detected in the frequency range 2–21
analysis of anomalies possibly caused by a well kHz above a depth of X042 m was generated
integrity problem. The 2011 temperature curve by the partial entry of the leaking fluid into the
features a heating anomaly that appeared after A formation. This reservoir has for a long time
the 2006 temperature survey, probably due to been used as a source of drinking water and
water entry into the casing annulus (Fig. 1). now apparently has low reservoir pressure.
2. Intense noise detected in the interval X049–
X055 m was caused by fluid flow through The rest of the water from the B formation,
the rock matrix. A temperature anomaly that did not enter A formation, flowed behind
indicating fluid entry into the casing annulus the casing to the surface and was the pressure
in this interval is not distinguishable due to a source for the C annulus. Low-frequency 0.6–2
masking effect caused by upward fluid flow. kHz noise detected by SNL between a depth of
However, the temperature gradient above the X071 m and the surface was caused by water
interval decreased, and the temperature curve flow through the casing annulus.
became vertical instead of tending towards the
geothermal profile. This points to the fact that Well integrity could be restored in this well by
the leaking fluid partly entered this interval and recementing.
partly flowed up towards the wellhead.
the tubing followed by the second run from was specified by the analysis of temperature 5/8” casing shoe. Both the SNL BLEED-OFF from the seal between 9 5/8” casing shoe and
the surface to 2685 m to assess the condition anomalies and anomalies in the intervals of and SND BLEED-OFF captured noises ranged in the top of 7” liner is attached.
of the 9 5/8” casing and the tubing, which possible leaks, including the 9 5/8” casing frequencies from 11 to 14 kHz at A5 and A6,
did not reveal any serious integrity issues of shoe installation depths. According to the stat- suggesting flow from these А5 and А6 units, The survey resulted in the recommendation
9 5/8” casing, 7” liner and 3 1/2” tubing. The ic temperature, the anomaly observed at the and low-frequency signals corresponding to to conduct an additional MBI logging to assess
well resumed to produce in June 2005. The interval of 9 5/8” casing shoe meant a possi- the noises produced by flows through the leak the tubing and casing corrosion.
A-annulus pressure measurement showed ble leak and source of gas in A-annulus. This
that the pressure reached 21 bar. interval was included into the scope of SNL
The 2011 Integrity Tests confirmed the A-an- bleed-off measurements. The bleed-off tem-
nulus pressure at 29 bar, which was then bled perature profile was measured from surface
down to 25 bar for 5 minutes. There was no to the reservoir section and spectral noise
communication detected between A and B an- logging was conducted in the zone of 9 5/8” Example 4 (Job ID-13110) As per technology, TGT recorded high-
nuli. casing shoe installation. Both the water and This well was drilled as a subsea gas condensate precision temperature and pressure logging
In November 2012, the HPT logging was con- the gas were recorded at the wellhead from producer, Slight gas bubbling in Annulus D data while running in hole and SNL at stations
ducted in the shut-in well and HPT-SNL sur- A-annulus during the bleed-off operation. The was observed after 3 years of production with while pulling out of hole. Surveys were carried
vey was run while bleeding off the A-annu- HPT data show difference between static and leak rate of 100 L/h at 113 m below sea level. under D-annulus bleed-off and A-annulus
lus, which pressure was 14 bar at the time of bleed-off temperatures from the A6 depth to injection conditions.
bleed-off operation. As the logging operations the surface, which means flow in the A-annu-
were restricted in time, the SNL bleed-off zone lus starting from the leak point in the zone of 9
Fig. 1 Leak detection survey (Temperature survey and Noise logging under 1) gas leakage to the surface
Fig. 1. HPT-SNL Logging data to determine a source of A-annulus pressure. through Annulus D and 2) during MEG 65% fluid injection into Annulus A).
During injection mode the pressure in Annulus The facts that low-frequency noise was
A increased to 1945 psi while the tubing detected all the way from the Main formation
head pressure remained at 2405 psi during to the surface under both conditions and the
the survey suggesting no communication temperature between the 13-3/8” casing and
between the tubing and the Annulus A. This the surface had numerous anomalies (see Fig.
is confirmed also by the fact that pressure, 2)
temperature and the noise spectrum
remained unchanged in both survey modes. Behind-casing cross-flow is confirmed by an
increase in low-frequency noise amplitude
High-frequency reservoir noises detected above the 20”casing shoe where the cement
across the main formation in the narrow bond was supposedly better (Fig. 2).
intervals in Zone1 were caused by reservoir
gas flow (Fig. 1). Apparently, this gas escaped In addition, conditions for cross-flow are
to the surface. The perforated interval was indicated by poor cement quality behind at
logged incompletely, and fluid inflow was least three strings of 7”, 9-7/8’’ and 13” sizes
assumed to have also come from below the detected by CBL, the results of which were
survey interval. not trusted by the clients.
Example 1 (Job ID-11030) (Fig. 2). The well was shut-in for two days
The main objective of the survey was to identify before the survey. During this period, the
the source of pressure for the C annulus (9- pressure in the C annulus (9-5/8” x 3-1/2”)
5/8” x 3-1/2”) in a deviated well producing increased to 170 psi and in the B annulus
from a terrigenous reservoir by natural lift. (13-3/8” x 9-5/8”) to 50 psi.
Additionally, the client reported excess pressure
in the B annulus (13-3/8” x 9-5/8”). The well A comparison of static and bleed-off
was surveyed by integrated high-precision measurements showed that the wellbore
temperature and spectral noise logging (HPT- temperature decreased after pressure bleed-off
SNL). from the C annulus. The highest temperature
variation was detected between the packer
HPT-SNL was performed in two modes: under and the wellhead. The bleed-off temperature
shut-in conditions and during pressure bleed- gradient changed substantially at the packer, as
Fig. 2 Low frequency SNL data. Correlation of noise data and 20” casing shoe. off from the C annulus (9-5/8” x 3-1/2”) compared to the static temperature gradient.
Example 2 (Job ID-12064) During an upward logging run, the packer was
The survey objective was to identify the source stripped. The annulus was closed for HSE reasons
of annulus pressure in a gas injection well, half an hour later and opened again 10 minutes
which was achieved using the integrated HPT- after that on a smaller choke. These changes in
SNL technique. pressure bleed-off conditions affected HPT-SNL
readings immediately and simultaneously.
The survey was performed in two modes: under
static conditions and during pressure bleed-off For instance, packer stripping was visualised as
from Annulus A. A static logging run was made temperature and pressure anomalies at Line A:
Fig. 1. Temperature and noise measurements showing a packer leak. after a long shut-in period. A significant cooling Annulus A produced substantial gas flow, and
anomaly indicating gas leakage was found at the well pressure started to decrease. As the packer
packer during pressure bleed-off from Annulus was open, Annulus A communicated with tubing
A. The noise data panel shows intense noise in and its pressure started to recover.
the entire frequency range indicating a leak at
the packer, while temperature data also contain When the tool was pulled up to Line B, Annulus
an anomaly at its depth. A was closed to stop the gas leak to the surface,
and annular pressure also started to recover.
When the tool reached Line C, Annulus A was the annulus under different conditions, and the suspected after acquisition of CBL data showing SNL captured high-intensity, high-frequency
reopened on a small choke. signal frequency depended substantially on a poor cement bond above and below the gas noise signals across a gas injection zone (A5).
bleed-off modes. storage. Such signals are normally associated with
SNL detected noise caused by gas flow through reservoir gas flows (Fig. 1). Similar noises were
To make sure there were no wellbore integrity also detected in the overlying (A2, A3 and A4)
problems, a spinner survey was conducted and underlying (A6) formations.
and then the wellbore was scanned with the
Electromagnetic Pulse (EmPulse) to check on The cooling anomalies in the static temperature
casing and tubing integrity. Logging data showed curve were caused by both lithological features
no cross-flows inside casing (Fig. 1). above A2 and adiabatic gas expansion during
pressure jumps in A5 and A4.
To identify any potential behind-casing The recorded low-frequency noise signals
cross-flows, reservoir-oriented surveys were and an analysis of temperature logs revealed
conducted, including Pulsed Neutron Logging communication between the gas storage Unit
(PNL), Spectral Noise Log High Definition (SNL- A5 and the overlying and underlying formation
HD) and High-Precision Temperature High Units A2, A3, A4 and A6 and determined the
Definition (HPT-HD) logging. cross-flow direction (Figs. 1 and 2).
Fig. 1. HPT-SNL data: temperature and pressure recorded under static conditions and temperature,
pressure and noise recorded during pressure bleed-off from Annulus A.
Example 1 (Job ID-13207) metal loss at X,907 ft between the packers (see
This case shows how the EmPulse tool captures a the Thickness 1 profile in Fig. 1a). Brown spots
tubing defect in a dual-barrier completion (Figs. indicating corrosion are present in both the
1a and 1b). Well OP-1 is a dual 3-1/2”-string oil NEAR and FAR DELTA panels at the same depth,
producer completed with 9-5/8” casing in two which means that the actual response is lower
pay zones. Its upper section contains two 3-1/2” than the simulated. The centre of the brown
tubing strings, 9-5/8” production casing, 13- spot is closer to the dashed line CL1, which
3/8” surface casing and 18-5/8” conductor cas- qualifies it as corrosion in the first barrier [28].
ing. Both long and short strings have the same
wall thickness of 0.254 inch, and the wall thick- The second barrier has the nominal thickness,
Fig. 2. Gas invasion by PNL data (shown in the "Lithology" column in yellow). Gas was found to ness of 9-5/8” production casing is 0.435 inch. as seen in the Thickness 2 profile, and no brown
accumulate in Units A5 and in the casing annulus. spots are intersected by the CL2 line, which sug-
The tubing-head pressure survey revealed the gests no corrosion in 9-5/8” production casing.
same pressure in the long and short strings,
suggesting downhole communication between A temperature log was recorded simultaneous-
them. A Multi Barrier Imaging survey was con- ly with the EmPulse log (Fig. 1a) and shows a
ducted in long string to check tubing for corro- gradient change across a defect located by Em-
sion and defects. Pulse, which indicates a leak through a corro-
sion hole (6).
Long string tubing thickness data revealed 30%
After completion of logging operations, the tub- tool can capture. Also note that, despite the
ing strings were retrieved and a 1.6”-by-1.2” close proximity and electromagnetic interfer- 3.2.2 CORRODED TUBING SECTION
corrosion hole was found across the leak area ence between the tubing and casing collars at
detected by EmPulse and temperature logs. It X880 ft, both were automatically identified by Example 1 (Job ID-13545)
should be noted that this particular defect is the EmPulse tool and software using a time re- This case shows how the EmPulse tool captures Most of the well contains 13-3/8” casing,
larger than the minimum defect the EmPulse sponse pattern. a tubing defect in a dual-string three-barrier i.e. the third barrier, that complicated the
completion, which is a challenging environment electromagnetic scanning of the second barrier.
for electromagnetic scanning because of
the asymmetric position of tubing strings in The survey revealed three corroded zones in
the wellbore. The current model describes tubing at X417 ft, X427 ft and X442 ft (Fig. 1).
axisymmetric systems (see Section 1.5), and the This section contains two 3-1/2” tubing strings,
calculation of the second barrier’s thickness is 9-5/8” casing and 13-3/8” casing.
impossible because of the influence of the short
string. The 9-5/8” casing was analysed only The centres of the brown spots are closer to
qualitatively in the two-string zone. For the zone the CL1 corrosion line on the NEAR DELTA and
containing only the long string, the thickness of FAR DELTA panels, which indicates corrosion in
the second barrier can be quantified. Well OP-2 the first barrier (the long 3-1/2” tubing string).
is a dual 3-1/2”-string oil producer completed Tubing thickness data in the Thickness 1 profile
with 9-5/8” casing in two pay zones. The of Fig. 1 shows a metal loss of at least 25% in all
objective of the Multi Barrier Imaging survey in three zones.
this well was to check the integrity of the long
string and locate zones of metal loss. The tool Corrosion of more than 10% in the first barrier
was run only once in a long string. can significantly distort the measured response,
Fig. 1a. Corrosion hole in a long tubing string at X,907 ft. The short string was located at a shallower
depth and was not captured in this depth interval.
Fig. 1. A corroded tubing joint with three distinct zones of metal losses at X417 ft, X426 ft and X442 ft.
Fig. 1b. Corrosion hole found in the long string at X,907 ft after retrieval. The temperature log shows a cooling anomaly at X442 ft caused by leaking.
losses below this collar as suggested by reduced tubing thickness and a brown spot intersected
and it can deviate from the modelled response The temperature sensor detected a cooling thickness and a faint yellow spot intersected by by the CL1 line. The temperature log shows a
in a wide time range. Red spots overlapping with anomaly at X442 ft right across the lower defect the CL1 line at X850ft. gradient change indicating a leak [29].
CL1 and CL2 may appear in the Far Delta panel, detected by EmPulse, suggesting that this zone The thickness profile, calculated for the long-string
with the maximum deviation (in their centres) corroded into a through hole and started to leak [29]. Another corrosion event was detected at X813 interval containing no short string, indicated no
still remaining on CL1. ft. The NEAR DELTA panel displays a decrease in metal loss in the 5” production casing.
The FAR DELTA panel data suggest no corrosion
in 9-5/8” production casing.
Example 1 (Job ID-13551) The survey revealed that a collar located at X850 Example 1 (Job ID-13420)
This case shows how the EmPulse tool captures ft had reduced thickness, as seen in the Thickness This case shows how the EmPulse tool The objective of the survey was to check the
corrosion in a tubing collar. Well OP-3 is a 1 profile (Fig. 1). Both the NEAR DELTA and FAR captures corrosion in the second barrier tubing strings and 10-3/4” casing for corrosion.
dual 2-3/8”-string oil producer completed DELTA panels show a brown spot extending from (10-3/4” casing).
with 5” casing in two pay zones. Downhole early times through an intersection with the CL1 The survey revealed no tubing corrosion, as
communication between the tubing strings corrosion line, thus indicating metal loss in this Well OP-4 is a dual 3-1/2”-string oil producer seen in the Thickness 1 profile and the DELTA
was suspected because of similar wellhead collar. The temperature log shows a gradient completed with 10-3/4” production casing in panels of Fig. 1.
pressures in them. The objective of the Multi change indicating that the collar was leaking. two pay zones. Most of the well contains 13-3/8”
Barrier Imaging survey in this well was to check There is a strong indication of 15% metal loss casing, i.e. the third barrier, which complicated However, the centre of a brown spot at X944
the integrity of the long string and locate zones in tubing one foot above the corroded collar. the electromagnetic scanning of the second ft in the FAR DELTA panel is closer to the CL2
of metal loss. There are also some indications of smaller metal barrier. corrosion line, which indicates corrosion in 10-
3/4” production casing.
Fig. 1. Tubing collar corrosion at X850 ft and tubing joint corrosion at X815 ft. Both defects are through-
hole leaks captured in temperature logs. Fig. 1. Corrosion in the second barrier. Metal loss was found at X944 ft in 10-3/4” production casing.
Example 1 (Job ID-14057) hole leak captured by the spectral noise logging
This case shows how the EmPulse tool captured tool (Fig. 1). The temperature log did not reflect
a leaking hole in tubing and multiple leaking this low-rate leak.
holes in casing. Well WD-1 is a water disposal Below that depth, the survey revealed numerous
injector completed with 5-1/2” tubing, 9-5/8” zones of corrosion in the X070–X100 ft interval
casing and 13-3/8” conductor strings. A (Fig. 2).
Multi Barrier Imaging survey in this well was
combined with temperature and spectral noise The thickness log indicated 60% metal loss at
surveys to check if water was injected into the X072 ft and 30% metal loss at X086 ft and X089
target formation. ft.
The survey revealed a massive metal loss of 80% The spectral noise log suggested that all three
in tubing at X051 ft that turned into a through- defects were leaking [29].
Fig. 2. Numerous corrosion holes in 9-5/8” casing. Three holes were picked up by the EmPulse tool, all
with noise extending to higher frequencies above 1 kHz, which clearly indicated an active leaks.
Fig. 1. Tubing corrosion. Almost 80% metal loss was found at X051 ft in 5-1/2” tubing. The spectral noise
log (SNL) suggested that this was a through-hole leak, as noise energy extended to higher frequencies.
The leak rate was low and was not picked up by temperature logging.
СHAPTER 3:
SPE PAPERS
1. UNDERSTANDING NOISES FROM DIFFERENT FLOW MEDIUMS IN NEAR WELL BORE
REGION: A NOVEL APPROACH FOR DETECTION AND CHARACTERISATION OF SUB-VERTICAL
NATURAL FLOW PATHS IN NORTH KUWAIT GAS FIELDS
NUMBER
OTC-26742-MS
AUTHORS
M. N. Acharya (Kuwait Oil Company) | A. Al-Mershed (Kuwait Oil Company) | S. R. Narhari (Kuwait Oil
Company) | M. Al-Azmi (Kuwait Oil Company) | Q. M. Dashti (Kuwait Oil Company) | S. Chakravorty
(Schlumberger Oilfield Eastern Ltd) | R. I. Abdulkadir (Shell Kuwait E&P) | S. Prosvirkin (TGT Oil & Gas
Services)
ABSTRACTS
Kuwait Oil Company is developing deep tight Gotnia formation, which has limestone stringers.
fractured carbonate and kerogen rich shale gas Fracture studies from several conventional cores
plays in northern part of Kuwait. Understanding and image log data could not conclusively infer
the flow medium is important to resolve ingress through going fractures into Gotnia, although
of offending fluids such as water and salt during many sub-vertical fractures of different nature
production history in the vertical/deviated wells have been observed and interpreted in the
SPE PAPERS
of this play. reservoir section in these logs.
СHAPTER 3:
These unconventional reservoirs have been This paper highlights the approach for detection
established to be hydrocarbon producing in and characterization of flow mediums, in
several prolific vertical producer wells, without the near well bore region (NWR) within a
having such early water breakthrough. The tight diameter of investigation of 3 meters or 10
fractured limestone reservoir is sandwiched feet. Results of spectral noise log (SNL), high
between salt-anhydride sequence above precision temperature (HPT), pressure and
(Gotnia cap rock) and Kerogen rich carbonate natural radioactivity (GR) of a vertical well
below. A dedicated casing is set at the top of logged in shut in and flowing mode helped in
limestone reservoir with the main objective of understanding different flow mediums such
isolating the Gotnia section prior to opening the as channel flow, fracture flow and reservoir
reservoir, as some sequences of anhydrites with flow. Thus the detection and characterization
calcite stringers in Gotnia are high pressured of different flow path systems with respect to
and prone to high water, CO2 and H2S. Based their spatial dimension and their interactive
on the current understanding, main source of flow contribution could be ascertained with
offending fluids is suspected to be the overlying high confidence.
2. INTEGRATED WELLBORE SUVEILLANCE TECHNIQUES FOR EFFECTIVE RESERVOIR 3. AN INTEGRATED DOWNHOLE PRODUCTION LOGGING SUITE FOR LOCATING WATER
MANAGEMENT PLAN SOURCES IN OIL PRODUCTION WELLS
NUMBER NUMBER
OTC-26414-MS SPE-178112-MS
AUTHORS AUTHORS
Aliasghar Saadat (PETRONAS) | M. Redzuan A. Rahman (PETRONAS) | Rahim Masoudi (PETRONAS) R. Bhagavatula (Kuwait Oil Company) | M. F. Al-Ajmi (Kuwait Oil Company) | M. O. Awad (Kuwait Oil
| Sharina M. Salim (PETRONAS) | Mohamad Othman(PETRONAS) | Fathi Younis Shnaib (TGT) | Company) | V. S. Rajagopalan (Kuwait Oil Company) | A. S. El-Daoushy (Kuwait Oil Company) | M. O.
Radhakrishnan Karantharath Hassan (Kuwait Oil Company) | F. Y. Shnaib (TGT Oilfield Services) | I. Aslanyan (TGT Oilfield Services)
| S. Prosvirkin (TGT Oilfield Services) | R. Karantharath (TGT Oilfield Services)
ABSTRACTS
Production optimization and improved recovery in acquiring the right data at the right time, and ABSTRACTS
efficiency while reducing operating and capital more importantly, integrating all acquired data Understanding of fluid movement in and near the using the TermoSim software application. SNL
expenditure has been the main goal of the to discern performance patterns, predict future wellbore is a crucial factor for effective reservoir identifies flowing zones and differentiates
operators, and makes it imperative under the behavior, and avert any problems. More detailed management including successful remedial between rock-matrix and fracture flows, and
current oil prices. Reservoir Management understanding of reservoir characterization and actions and field development planning. One of TermoSim then numerically models heat
Programme (RMP) is a comprehensive and reservoir physics are the need of the hour to be the key objectives in well surveys is to detect exchange between the wellbore fluid and the
integrated process of establishing control over efficient and successful in the various stages of and locate sources of fluid flows behind multiple surrounding rocks and reservoirs. The resulting
hydrocarbons appraisal, extraction, voidage the exploitation of the reservoir. pipe barriers. The conventional Production model quantifies fluid production from each
replacement, and optimizing production and Furthermore, advances in horizontal drilling, Logging Tool (PLT) is run to detect fluid flow reservoir unit. Conventional production logging
reservoir performance, and it is the key to smart well completions, deep-sea drilling, and and identify the type of fluid under downhole (PLT) locates fluid entry points in the wellbore.
achieving maximum recovery. Monitoring highly complex operation, have changed the conditions, but is limited to measurements only The integrated HPT-SNL and PLT logging suite can
well and reservoir performance from initial playing field and rendered many old conventional inside the wellbore. Similarly, other diagnostic trace the entire water path from the reservoir
completion to abandonment is critical to ensure tools inadequate to meet the new challenges. techniques, such as cement bond logging, give into the wellbore.
efficient operation, optimum economics, and For example, rates from some intervals along a insight only into the cement integrity and also This paper describes water source identification
safe environment. Tracking production rates, horizontal well can be too low to be measured have limited capabilities to detect cross flows by an HPT-SNL-PLT logging suite deployed in
water cut, wellhead pressure, casing pressure, by a typical flowmeter. The cost of measuring behind casing. several production wells of a Kuwait oil field. In
well integrity, and planning recompletion, reservoir pressure in individual layers can be cost Recent developments in temperature and noise some of the wells in this field, it has been found
workovers, sidetracks, in-fill drilling, enhanced prohibitive, especially once the completion is in logging tools and advanced interpretation that water encroached into the perforations
oil recovery etc. will require close watch, place. Reservoir characterization, understanding techniques have provided higher resolution and from a watered reservoir below through a
accurate analysis, and timely execution at lateral continuity, and permeability anisotropy sensitivity, enabling the detection of previously channel behind the casing. In other wells, it
considerable cost and effort. Therefore, it can be time consuming and expensive. Locating undetectable leaks and fluid flow behind casing has been found that cold water breakthrough
is critical to stay up-to-date on the latest the source of a casing pressure accurately, [1]. occurred laterally from nearby water injectors.
developments in technological advancements quickly, and without having to mobilize special In the present case, a water zone has been The exact identification of water sources is a
in this area, be judicious in the methods used equipment (rig-less) is critical. identified in a producing formation with High crucial step in any further well remedial work
Precision Temperature (HPT) logging and to reduce or eliminate them from oil producing
Spectral Noise Logging (SNL) followed by wells.
advanced numerical temperature modelling
4. INTEGRATED FORMATION MICROIMAGER (FMI) AND SPECTRAL NOISE LOGGING (SNL) 5. QUANTIFICATION OF RESERVOIR PRESSURE IN MULTI-ZONE WELL UNDER FLOWING
FOR THE STUDY OF FRACTURING IN CARBONATE RESERVOIRS CONDITIONS USING SPECTRAL NOISE LOGGING TECHNIQUE, ZUBAIR RESERVOIR,
RAUDHATAIN FIELD, NORTH KUWAIT
NUMBER
SPE-177616-MS NUMBER
SPE-177620-MS
AUTHORS
Arthur Aslanyan (TGT Oil & Gas Services) | Irina Aslanyan (TGT Oil & Gas Services) | Roza Minakhmetova AUTHORS
(TGT Oil & Gas Services) | Yulia Maslennikova(TGT Oil & Gas Services) | R. Karantharath (TGT Oil & Gas A. Aslanyan, I. Aslanyan, S. Prosvirkin, TGT Oilfield Services |R. Farakhova, Sofoil.
Services) | Badar Al Hadhrami (TGT Oil & Gas Services) | Zaaima Al Gafri (Petroleum Development of
Oman) ABSTRACTS
Monitoring the reservoir pressures throughout acoustic noise signal generated by a reservoir
ABSTRACTS the production life of the field is considered as fluid flowing from a particular unit is directly
Carbonate reservoirs are known to contain based on concurrent deployment of Formation a cornerstone for reservoir management and proportional to the product of differential
considerable hydrocarbon reserves. There MicroImager (FMI) and Spectral Noise Logging optimization of the development plans. There pressure and flow rate. Nonlinear relationship
are, however, several challenges that may Tool (SNL) has considerably improved the are many challenges to have routine and proper between the noise power and bottom-hole
complicate the process of development of this interpretation of this scenario. pressure records. Multi-zone single completion flowing pressure has been utilized to estimate
type of reservoirs, such as low porosity and high This paper gives some examples of carbonate wells are one of these challenges, where it is the average reservoir pressure which stays
degree of fracturing and heterogeneity, which, reservoir surveys conducted in the wells located difficult to acquire the reservoir pressure for valid under monophasic flow conditions for the
cumulatively, could result in a low oil recovery in one of the Middle Eastern fields. It has been each zone through the conventional pressure hydrocarbon to the wellbore.
factor (RF). Optimisation of development shown that spectral noise logging data have gauges. In addition to that, deferring the The estimated pressures for each layer from this
process in carbonate fields is impossible a high degree of correlation with FMI data production or injection of high rate wells for technique matched the RFT pressure data that
without preliminary reservoir studies focused resulting from fracturing analysis. The active quite time to acquire downhole static pressure have been recorded in the nearby wells and in
on assessment of their production potential. fracture flow zones have been distinctly outlined data is adding more to these challenges. also RFT data recorded in same well considering
Such studies include an analysis of complex by Spectral Noise Logging data and further Raudhatain Zubair Reservoir is a layered the production history. The noise profile has
pore space structure and local system of confirmed by High-Precision Temperature reservoir with difference in reservoir pressure also indicated the effective sand thickness for
faults and fractures that may serve both as Logging data. The advantages offered by joint from layer to the other. Spectral Noise Logging each layer and investigated flow behind the
enhanced reservoir capacity and flow channels. application of SNL and FMI techniques for technique has been utilized to estimate the casing from non-perforated reservoir to the
Conventional logging techniques (for example, studying carbonate reservoirs have therefore average reservoir pressure for each perforated existing perforations.
high-precision temperature logging and been clearly demonstrated. This approach can layer in a Multi-zone single completion oil Utilization of the SNL logging to estimate the
spinner surveys) solely used for estimation be successfully applied for the study of both producer. The noise logging survey has been reservoir pressure is adding more to reservoir
of reservoir productivity may have a limited natural and induced fractures. carried out under flowing conditions and on surveillance applicable tools that could mitigate
scope of application. An integrated approach different rates. The process of estimation the some of the existing challenges and aiming to
average reservoir pressure from Noise logging improve the surveillance process under certain
is based on quantification of the noise power circumstances.
under different rates. The signal recorded by This paper presents a case of applying the noise
SNL has two main parameters: amplitude and logging in an oil producer with the detailed
frequency. The frequency ranges widely from job procedures, measured data, interpretation
8 Hz to 60 kHz, while the amplitude increases process, and the final results
with differential pressure. The power of the
6. THE SOUND OF HYDROCARBONS & THE FLUIDS TEMPERATURE. AN INTEGRATED 7. CORRECTLY ALLOCATING INJECTED GAS TO TARGETED ZONES BY INTEGRATING DATA
PRODUCTION LOGGING APPROACH FROM SPECTRAL NOISE AND TEMPERATURE LOGS
NUMBER NUMBER
OMC-2015-467 SPE-177827-MS
AUTHORS AUTHORS
G. Galli (Eni E&P) | G. Rizzo (Eni E&P) | A. Leone (Eni E&P) Khaled Mohamed Alabd (ADCO) | Faizal Riza (ADCO) | Nawal Al Nuaimi (ADCO)| Ahmed Fawzy (ADCO)
| Mohamed Moussa (ADCO) | Fathi Shnaib (TGT) |Mohamed El Sheshtawy (TGT) | Maxim Volkov
ABSTRACTS (TGT) | Vener Nagimov (TGT) |Sergey Vorozhikhin (TGT)
The reservoir and well monitoring is a critical The High Precision Temperature (HPT) and
input to develop an effective reservoir Spectral Noise Log (SNL) suite by TGT Oilfield ABSTRACTS
management strategy. Generally, one of the key Services Co. have innovative features such as Gas Injection alone, or in Water Alternating Effective reservoir management requires active
issues in diagnosing well performance is detect large radii of investigation, scanning through Gas (WAG) mode to improve oil recovery (IOR) & efficient reservoir surveillance in order to
fluid flow behind multiple barriers, which are not multiple barriers and high-resolution data. HPT has been widely applied since the late 1950s. optimize well & reservoir performance. It is,
clearly identified by conventional temperature is composed by a platinum super-sensitive fast- The incremental oil recovery attributed to IOR therefore, critical to design a proactive program
and noise logs. So far, the Production Logging response temperature sensor that can pick up has been generally estimated at 5 – 10% over for data acquisition, integrating that data
Tool (PLT) approach has been considered the smallest leak-generated perturbations of Secondary Recovery (water injection alone), into a knowledge data base and to transform
essential to identify production/injection zones wellbore-fluid temperature through multiple primarily due to preferential sweep under that knowledge into valuable information to
and to recognize the type of fluid at down- barriers providing inflow profile, whereas SNL gravitational effects. Theoretically, water and guide future operations for remedial work,
hole conditions only in the wellbore. Likewise, is composed by a new hydrophone generation gas injection tend to have preferential sweep recompletion, infill drilling, and further
cement log used to evaluate cement integrity is that detects noise in a wide frequency range. due to gravitational effects and formation development programs.
blind through tubing or multiple barriers [2]. This paper presents the first eni application in oil characteristics. In practice, however, it is an This paper discusses in detail how the injection
However, recent developments in temperature producer well located in brown field using new operational challenge to obtain a uniform profile geometry was described, and injected
and noise logging tools and interpretation SNL-HPT tools compared with the “conventional sweep across the reservoir. gas volumes were correctly allocated to targeted
techniques have been rewarded by achieving Production Logging Tool technology” (PLT) in One of the biggest challenges in understanding zones in one of the giant onshore oil fields in Abu
higher resolution and sensitivity characteristics order to optimise and integrate the resulting the injection behavior in gas injection wells using Dhabi, UAE operated by ADCO, using integrated
enabling the detection of previously well information. the conventional production logging approach HPT (High Precision Temperature) and SNL
undetectable fluid-flow behind the casing and is to identify the exact entry points, and to (Spectral Noise Logging). Data from HPT and SNL
leaks. determine a representative injection profile logging package was integrated to successfully
to the actual injection volumes. Mechanical monitor water injection, identify cross-flows
spinners provide inflow profiles within the and locate casing leaks in injection wells for
borehole that in many cases doesn’t reflect the the past 2-3 years. Based on the performance,
actual gas behavior inside the addressed layers reliability, and accuracy of this advanced
beyond the entry point. logging technology, ADCO has decided to use
Gas containment in the reservoir and within the same tools and temperature simulation to
the targeted zone is one of the biggest hurdles. track gas injection, gas flow profile behind pipe,
Unlike pilot projects, in full field application, and to monitor any communication with any
channeling, cross flows, out of zone injection extraneous thief zones.
and premature breakthrough often occur,
resulting in wasting gas, delayed response, and
lower than expected recovery.
8. FORMATION PRESSURE EVALUATION FOR PRODUCING WELLS WITHOUT SHUTTING 9. ACOUSTIC-BASED METHODOLOGY OF ASSESSING ZONAL PRODUCTION CONTRIBUTION,
DOWN THE WELL, USING MULTI RATE HIGH PRECISION TEMPERATURE AND SPECTRAL NOISE HYDRAULIC FRACTURE PRODUCTIVE HEIGHT, AND RESERVOIR FLUID TYPE IN TIGHT GAS
LOGGING (HPT-SNL) CONDENSATE AND OIL RESERVOIRS
NUMBER NUMBER
SPE-177892-MS SPE-176863-MS
AUTHORS AUTHORS
Arlen Sarsekov (ADMA-OPCO) | Abbas Al-Alyak (ADMA-OPCO) | Ahmed Al Neaimi (ADMA-OPCO) | Labib Mohsin (Oman Oil Co. E&P) | Norhafiz Marmin (Oman Oil Co. E&P) |Alexander Mukha (TGT
Omar Yousef Saif (ADMA-OPCO) | Mohamed Helmy(ADMA-OPCO) | Fazeel Akram (ADMA-OPCO) | Oilfield Services)
Mohamed Saber (ADMA-OPCO)| Jawdat Bilbeisi (ADMA-OPCO) | Tarik Mansouri (ADMA-OPCO) |
Fathi Shnaib(TGT Oilfield Services) | Rafael Khamatdinov (TGT Oilfield Services) | Vasiliy Skutin (TGT ABSTRACTS
Oilfield Services) | Rushana Farakhova (TGT Oilfield Services) |Irina Aslanyan (TGT Oilfield Services) | For a tight reservoir, assessment of zonal directly to well productivity.
Ruslan Makhiyanov (TGT Oilfield Services) production contribution is often possible only Integrating acoustic logging to conventional
after the reservoir has been hydraulically production logging measurements may, in
ABSTRACTS fractured. Spinner survey is commonly the tool addition to increasing resolution for low
Majority of the oil and gas fields in the measuring each sublayer pressure for producing of choice for diagnosing relative production flow measurement, significantly extend the
UAE are mature multi-layered carbonates wells without interruption of the production contribution across perforated interval in investigation radius beyond casing wall. Different
reservoirs, which determines complex vertical and properly defining any differential pressure a cased-hole and by extension, minimum acoustic characteristics potentially exhibited
heterogeneity and challenging development between sublayers. This will help when applying productive fracture height at the wellbore. by flow of different fluid phases may also
of those reservoirs. Conventional methodology any gas shut-off or water shut-off techniques However, its limited radial resolution renders validate conventional log-derived reservoir fluid
to measure sublayer pressure is to utilizing and prolong the life of producing wells, as well such tool unreliable in evaluating flow types. The paper describes the application of
different wireline formation testers for any new as to help future development of the field. The characteristic within fracture body and across acoustic logging in diagnosing zonal production
well or worked over well before commissioning determined reservoir pressure for each layer fracture planes. The acquired data is generally contribution, fracture height, and reservoir fluid
for production. Once well is completed has been compared with recent formation insufficient for resolving relative contribution of type across hydraulically fractured tight gas
and put on production; usually the average pressure tester measurements obtained for this various productive horizons intersected by the condensate and oil reservoirs.
reservoir pressure is measured at the depth of well. The pressure measurement is in the range fracture. As the measurements are focused on In four naturally flowing wells, zonal production
perforation using conventional pressure build of 20 psi tolerance. flow characteristics inside the wellbore, fracture contribution derived from acoustic wave analysis
up (PBU) or bottomhole closed-in pressure Identification of sublayer reservoir pressure height diagnosis is limited by the extent of and conventional production log data were both
(BHCIP) methods. Using conventional approach for each producing interval is vital for highly perforation interval. Alternatively, radioactive in good agreement. The analysis of depth-specific
it is always difficult to understand which layers heterogeneous multi-layered reservoirs. This tracing and microseismic survey allow one to acoustic wave amplitude provided useful insight
are more depleted than others, as only average technique is important for gas and water see through the casing wall albeit at the expense in the diagnosis of zonal production contribution
reservoir pressure is recorded in the wellbore. production management when one or several of heightened cost and operational complexity. and by extension, productive fracture height. In
In case of the heterogeneous multi-layer sublayers become depleted. Appropriate action Thermal logging, being a cheaper alternative, is one well, acoustic-derived fracture height could
reservoirs, pressure measured conventionally for gas/water shut-off technique can be applied time-sensitive and not deployable immediately be closely corroborated with that of radioactive
in the wellbore will be at most of the times, in the right time which will help to manage following proppant placement due to restricted tracer data. In addition, one may also observe
inadequate for sublayer pressure estimation. reservoir efficiently, as well as reducing the wellbore access. Most importantly, hydraulic distinct shape of maximum amplitude of first
This paper will describe new methodology of cost for conventional pressure measurements and propped fracture heights diagnosed by sound wave arrival in a gas well compared to
formation pressure evaluation, as well as real and eliminating the loss of production due to these methods may not necessarily coincide that in an oil well.
case study done in one of the developed offshore shut in time for pressure stabilization during with effective fracture height that contributes
carbonate field in the UAE. This method allows conventional BHCIP or PBU.
10. TRIPLE-BARRIER THICKNESS SCANNING USING THROUGH-TUBING PULSE-MAGNETIC independently by High-Precision Temperature wells that were to be abandoned. The results
LOGGING TOOL Logging and Spectral Noise Logging of the MID surveys were then used to design
The above metal losses have been located by environmentally safe abandonment procedures.
NUMBER through-tubing memory surveys in offshore
SPE-176655-MS
AUTHORS
Arsalan A. Ansari (Zakum Development Co.) | Ziad Libdi (Zakum Development Co.) | Naeem Khan 11. ASSESSING MACROSCOPIC DYNAMIC PERMEABILITY THROUGH PRESSURE AND NOISE
(Zakum Development Co.) | Arthur Aslanyan (TGT Oilfield Services) | Irina Aslanyan (TGT Oilfield ANALYSIS
Services) | Maxim Volkov (TGT Oilfield Services) | Andrey Arbuzov (TGT Oilfield Services) | Andrey
Achkeev (TGT Oilfield Services) | Fathi Shnaib (TGT Oilfield Services) | Ruslan Makhiyanov(TGT Oilfield NUMBER
Services) SPE-175550-MS
ABSTRACTS AUTHORS
Servicing oil and gas wells requires their integrity parallel computing with multi-core processors Arthur Aslanyan (TGT Oil and Gas Services) | Irina Aslanyan (TGT Oil and Gas Services) | Rushaniya
assessment both during operation and before to process data within a reasonable time frame. Farakhova (Sofoil LLC)
abandonment. One of the main objectives in well The MID hardware and interpretation algorithm
integrity analysis is the location of metal losses have been tested on multiple laboratory stands ABSTRACTS
in tubing and/or casing caused by corrosion, simulating various downhole multi-barrier One of the common applications of Pressure poor porosity-permeability, complex pressure
erosion or other types of pipe damage. The completions from 2–7/8? up to 13 3/8? pipes Transient Analysis and Pressure Pulse Testing is transient responses and others. In many cases,
first three metal barriers (normally tubing, with artificial defects of various shapes and the evaluation of formation permeability that is inaccurate dynamic permeability values are due
production casing and intermediate casing) are sizes ranging from 7 mm to 140 mm. referred to as dynamic permeability and is then to misinterpretation of flowing thickness.
of the most interest to the industry. Dual string This paper presents laboratory results and used to calibrate permeability distribution from In this paper, we demonstrate how Spectral Noise
completions is an additional complication to three selected field cases demonstrating the a geological model before running full-field flow Logging can pick the boundaries of actual flow
through-tubing assessment of the second and application of Magnetic Imaging Defectoscopy simulations. units and enable the accurate determination of
third barriers. (MID) in single-string and dual-string In practice, though, the correlation between effective thickness to substantially improve the
Magnetic Imaging Defectoscope (MID) is an completions for thickness evaluation of three permeability from pressure tests and that correlation between dynamic and open-hole
electromagnetic scanning tool that recor barriers independently by a memory through- predicted from open-hole logs is often poor and permeabilities.
ds magnetisation decays induced by high-power tubing survey. does not provide consistent calibration because
electromagnetic pulses. Metal pipe barriers Well W-01 with metal losses found at the same of many factors including poor core data,
contribute to magnetisation decays at different depth in the second and third barriers, i.e. 9
times depending on their diameters, which 5/8? and 13 3/8? casings
makes it possible to differentiate each of them Well W-02 with metal loss found in the second
and determine their individual thicknesses. barrier, i.e. 9 5/8? casing, in an interval containing
Thickness determination requires the numerical two strings. This corrosion has been confirmed
finite-element modelling of each recorded by a repeated MID survey after pulling out the
magnetisation decay and iterative fitting of the completion
properties and thickness of every metal barrier Well W-03 with through-hole metal loss found in
to the actual tool readings. A data array can store the second and third barriers, i.e. large-diameter
hundreds of thousands decays, and the data 9 5/8? and 13 3/8? casings, through a 7? liner.
processing optimisation loop therefore requires This through-hole corrosion has been confirmed
12. SPECTRAL NOISE LOGGING INTEGRATED WITH HIGH-PRECISION TEMPERATURE 13. PLANNING INFILL DRILLING AND WORKOVER PROGRAMMES BASED ON RESERVOIR-
LOGGING FOR A MULTI-WELL LEAK DETECTION SURVEY IN SOUTH ALBERTA ORIENTED PRODUCTION LOGGING SURVEYS
NUMBER NUMBER
SPE-175450-MS IPTC-18173-MS
AUTHORS AUTHORS
Arthur Aslanyan (TGT Oilfield Services) | Irina Aslanyan (TGT Oilfield Services)| Radhakrishnan Arthur Aslanyan (TGT Oil & Gas Services) | Irina Aslanyan (TGT Oil & Gas Services) | Radhakrishnan
Karantharath (TGT Oilfield Services) | Roza Minakhmetova(TGT Oilfield Services) | Hassan Kohzadi Karantharath (TGT Oil & Gas Services) | Sergey Matveev (TGT Oil & Gas Services) | Vasilii Skutin (TGT
(Global New Petro Tec Ltd.) | Mohsen Ghanavati (Global New Petro Tec Ltd.) Oil & Gas Services) |Marat Garnyshev (TGT Oil & Gas Services) | Damien Bevillon (Dubai Petroleum
Establishment) | Nagendra Mehrotra (Dubai Petroleum Establishment) | Nelson Suarez (Dubai
ABSTRACTS Petroleum Establishment)
Gas or fluid ingress into the cement channel Regulator (AER) to identify and eliminate leaks
and then up to the surface through the surface and perform remedial operations as outlined in ABSTRACTS
casing annulus is called Surface Casing Vent AER’s rules and directives. Wellbore fluid flow profiles in both producers [1,2] and High Precision Temperature (HPT)
Flow (SCVF), which causes Sustained Annulus Even if a well is to be abandoned, the operators and injectors tend to change over time due Logging [3–5]. PLT and HPT-SNL produce
Pressure (SAP) as a common occurrence in must precisely identify the location of the leak to preferential depletion, formation damage, similar results when wellbore and completion
the petroleum industry. Gas may also migrate and its source to perform a successful plug-and- cross-flow, channelling or tubing or casing conditions are good but they may differ
to the surface outside the outermost casing abandonment (P&A) operation. P&A activities leaks. These changes can result in excess water dramatically in cases of non-uniform formation
string, which is often referred to as external are non-revenue generating activities. The production through channelling, coning, non- damage, channelling behind pipe or plugging of
Gas Migration (GM) or seepage. In some right diagnostic technology is critical for correct uniform water breakthrough (fingering) or out- perforations by scale. Generally, HPT-SNL would
countries with shallow coal reserves, gas leak source identification to eliminate the of-zone injection – all leading to uneven flow, assess the flow geometry and invaded zones of
migration sometimes occurs in association with costs associated with numerous unsuccessful pressure and sweep profiles. Ignoring these the reservoir while PLT would point out where
coalbed gas (CBG) development. Dewatering attempts. complications can result in missing key points fluid enters or leaves the wellbore or tubing.
the coal seams or lowered water levels in coal, The technique of Spectral Noise Logging (SNL) on reservoir behaviour, selecting wrong units The paper provides case studies from a mature
whether induced by drought or by domestic coupled with High Precision Temperature (HPT) for a 3D full-field flow model or misleading offshore waterflooded field producing a mix of
aquifer pumping, can result in the release Logging have extensively benefited oil industry redevelopment planning. Therefore, it would oil, gas, formation water and injection seawater,
of methane and other natural gases in coal outside Canada in accurately identifying fluid be logical to check for changes in flow geometry which complicates the identification of flow
(NGC). Hydrocarbon gases released into the flow behind multiple casing pipe barriers and before embarking on costly workovers, geometry and invasion zones and represents a
atmosphere is an environmental concern. More in locating leaks and their sources [3–5]. This recompletion or infill drilling programs. challenge for reservoir engineers in developing
importantly, leaking fluids may contaminate paper describes two case histories for eight This paper compares and integrates the results proper drilling or workover programmes to
subsurface fresh-water reservoirs, resulting in wells in the Western Canadian Sedimentary of conventional Production Logging Tool (PLT) target residual reserves [6, 7]. The HPT-SNL-
a major catastrophe for the environment and Basin (WCSB) in South Alberta region for two surveys that use spinners and multiphase PNL surveys and further studies described here
human population. clients, where application of these techniques sensors with those acquired by reservoir- led to successful workovers and drilling. The
According to the latest statistics, 6% of almost enabled gas leak source identification in a series oriented production logging surveys employing redevelopment results can be easily assessed
270 000 operating and idle wells analysed in of wells suffering from minute leak rates and a combination of Spectral Noise Logging (SNL) by decline curve analysis.
Alberta were found to contain leaks, 5.5% of also helped to discover some regional lateral
them having SCVF and 0.5% gas migration [2]. flows and cross-flows.
Operators are bound by the Alberta Energy
14. NUMERICAL TEMPERATURE MODELLING FOR QUANTITATIVE ANALYSIS OF LOW- 15. IDENTIFICATION OF BEHIND-CASING FLOWING RESERVOIR INTERVALS BY THE
COMPRESSIBLE FLUID PRODUCTION INTEGRATED HIGH-PRECISION TEMPERATURE AND SPECTRAL NOISE LOGGING TECHNIQUES
NUMBER NUMBER
SPE-172090-MS SPE-171251-MS
AUTHORS AUTHORS
Arthur Aslanyan (TGT Oilfield Services) | Irina Aslanyan (TGT Oilfield Services)| Andrey Salamatin (TGT A.A. Lutfullin (Novatek-Tarkosaleneftegaz LLC) | A.R. Abdrahimov (Novatek JSC) | I.N. Shigapov (TGT
Oilfield Services) | Andrey Karuzin (TGT Oilfield Services) | Yulia Fesina (TGT Oilfield Services) | Ilnaz Oilfield Services) | I.Yu. Aslanyan (TGT Oilfield Services) | A.M. Aslanyan (TGT Oilfield Services) | R.K.
Zaripov (TGT Oilfield Services) | Vasiliy Skutin (TGT Oilfield Services) | Zaaima Al Ghafri (Petroleum Kuzyutin (TGT Oilfield Services)
Development Oman) | Mohamed Khalid Yarabi (Petroleum Development Oman)| Abdulaziz Ali Al-
Maharbi (Petroleum Development Oman) ABSTRACTS
Hydrocarbon production from low permeability production logging can produce valuable
ABSTRACTS reservoirs has been steadily growing in the information on gas, oil and water flow profile
Temperature logging is an efficient technique to and long-term lateral flows that can disturb the Russian Federation lately. The reservoir sweep and behind casing communication (whether a
locate inflow intervals in the reservoir, evaluate temperature at any depth, and calculates fluid efficiency and behind casing integrity has cement rim channeling or a reservoir fracture
inflow rates in them and the drawdown rates for each formation unit and temperature become even more important than it was in flow). The technology is illustrated with three
pressure that creates temperature disturbance, profiles for the wellbore and for any distance conventional formations – mainly because case studies from the East-Tarkosalinskoye field
detect cross-flows in the wellbore and/or from it. the target oil/gas pays has experienced tough of the Yamalo-Nenets Autonomous Region
behind casing and check for casing, tubing and This paper describes the general physical and competition from higher permeable water (North Russia). One case was a vertical well and
the bottom-hole leakages. Temperature logging mathematical models and user interface of the pays. In high permeability formations one the two others are horizontal wells with multi-
can detect wellbore flows with rates way below TERMOSIM TSMp simulator for producers and can normally track production profile with a zone hydraulic fracturing. An integrated analysis
the mechanical spinner’s threshold. Another presents modelling results for two production conventional production logging tool based on a of acquired data identified the sources of water
impressive application of temperature logging wells of Oman. For each well, the TSMp mechanical spinner and based on that schedule production and also revealed the non-producing
is picking flow zones behind unperforated simulator has been employed to create a best- the treatment to arrest water cut growth. In low reservoir zones. Special attention was paid to
casing that develop through behind-casing fit individual thermohydrodynamic model and permeability formation most communication the analysis of annular and behind-casing cross-
channelling. Such findings can be verified or match downhole pressure and temperature happen behind the casing and those flowing flows.
discarded through numerical simulation of records for different production rates. The well inside the borehole are usually too slow to be One horizontal well was worked over with a
temperature logs. This paper presents the TSMp log analyses based on temperature modelling captured by the mechanical spinner. cementing job around the zone identified as
solver module of the TERMOSIM simulator that presented in these case studies open the way to This paper shows how high-sensitivity the water source from the HPT-SNL survey and
can reproduce complex hydrodynamic flow (a) identify actual reservoir inflow intervals, (b) broadband Spectral Noise Logging [1-4], High- resulted in total shut-down of water production
patterns and the associated thermodynamic evaluate formation pressure in flowing units, (c) Precision Temperature Logging [1] and flow with no impact on oil production.
effects, taking place during fluid flows through evaluate inflow rate from each flowing unit and modeling in combination with conventional
a multi-layer reservoir towards the wellbore (d) distinguish between wellbore cross-flows
and theirblending in it, including heat exchange and behind-casing channelling.
between reservoir and wellbore flows and the The case studies presented in this paper are
surrounding rocks. focused on low-compressible, mostly single-
The TSMp solver takes into account possible phase fluids with high water or oil and low
inter-reservoir communications both inside and free-gas contents (while multiphase flows with
outside casing caused by the pressure difference abundant free gas will be covered in a separate
between formation units, as well as short-term paper).
16. TIME-DOMAIN MAGNETIC DEFECTOSCOPY FOR TUBING AND CASING CORROSION 17. EVALUATION OF WATER FLOODING EFFICIENCY THROUGH THE STATIC HIGH PRECISION
DETECTION TEMPERATURE LOGGING
NUMBER NUMBER
SPE-169601-MS SPE-166007-MS
AUTHORS AUTHORS
A. Aslanyan (TGT Oil & Gas Services) | I. Aslanyan (TGT Oil & Gas Services) | A. Arbuzov (TGT Prime) | B. Irina Aslanyan (TGT Oil & Gas Services) | Jamal Barghouti (TGT) | Abdullah Juma Al Shammakhy
Zagidullin (TGT Prime) | T.A. Al-Rahawi (TGT Oil & Gas Services) | S. Prosvirkin (TGT Oil & Gas Services) (Petroleum Development Oman)
| M.F. Al-Ajmi (Kuwait Oil Company) | M.O. Awad (Kuwait Oil Company) | S.S. Sharma (Kuwait Oil
Company) | M. Das (Kuwait Oil Company) ABSTRACTS
The paper shows how high-precision a numerical model to actual temperature logs
ABSTRACTS temperature (HPT) logging and numerical can be used to describe the injection pattern
The Magnetic Imaging Defectoscope (MID) is differential (DELTA) data panels, based on the temperature modelling for radial flow injection including complicacies caused by behind-casing
a tool designed to record the time response difference between numerical models and (TERMOSIM) assess the performance of water channelling. Particular attention is given to how
to high-energy electromagnetic pulses. Metal actual responses, that visualise electromagnetic injection wells, and outlines specific features temperature logging and modelling complement
presence around the tool is evaluated by signatures of metal structures and can be used of modern temperature logging tools and information obtained by the conventional PLT
matching measured and numerically modelled to locate and recognise various completion logging procedures. The basic principles and technique based on the mechanical spinner. The
magnetisation decays. The air response decays components, such as packers or SSD. critical elements of temperature modelling concept and basic features of the TERMOSIM
faster than if the tool is placed inside a metal The paper describes the basics of the for injection wells are discussed. The paper temperature modelling software are given in
pipe. If multiple pipes are present around the time-domain magnetic-pulse technology, presents five cases illustrating how the fitting of the Appendix.
tool, the near pipe responds at earlier times specifications of the tool itself and laboratory
and the more distant ones at later times. This test data. This technology has been tested
phenomenon is key to detecting metal presence in a dual-string producer of the Raudhatain
in each individual pipe. The MID tool features field operated by the Kuwait Oil Company.
two sensors, short and long, to ensure reliable The long and short strings were suspected to
detection of responses from a wide range of be communicating due to identical water cut
multi-barrier completions and differentiate trends. The MID tool was run once in memory
between defects in each barrier independently. mode on slickline through the long string and
Despite this simple concept, the response detected a 1.5-inch corrosion hole between
detected by the tool has a complex time packers that created communication with the
behaviour and cannot be modelled in a short string. This communication flow left a
simple analytical way, which put time-domain footprint in a shut-in temperature log right
technologies on hold for many years. The across the corrosion hole. Another corrosion
recent advances in computer speed and hole was located in the casing below the tubing
multicore parallel computing enable accurate shoe, immediately above the perforations.
numerical modelling of complex responses During a subsequent workover, the tubing was
and determining metal presence in two metal retrieved and a 1.5-inch corrosion hole was
barriers separately. In addition to thickness located in the exact place where it was identified
profiles for each barrier, the MID tool generates by the MID tool.
18. COMPLEMENTING PRODUCTION LOGGING WITH SPECTRAL NOISE ANALYSIS TO 19. LEAK DETECTION BY TEMPERATURE AND NOISE LOGGING
IMPROVE RESERVOIR CHARACTERISATION AND SURVEILLANCE
NUMBER
NUMBER SPE-161983-MS
SPWLA-2013-TTT
AUTHORS
AUTHORS Ihab Nabil Khalil (Abu Dhabi Co. Onshore Oil Opn.) | Maxim Filenev (Kazan State University) | Arthur
Nelson Suarez (Dubai Petroleum Establishment) | Ademola Otubaga (Dubai Petroleum Establishment) Aslanyan (TGT Oil and Gas Services) | Irina Aslanyan (TGT Oil & Gas Services) | Jamal Barghouti (TGT
| Nagendra Mehrotra (Dubai Petroleum Establishment) | Arthur Aslanyan (TGT Oil and Gas Services) Oil Co.) | Mohamed Hassan El-Hamawi (Abu Dhabi Co. Onshore Oil Opn.) | Rasheed Ahmad Al-Hassan
| Irina Aslanyan(TGT Oil and Gas Services) | Murat Khabibullin (TGT Oil and Gas Services) |Michael (Abu Dhabi Co. Onshore Oil Opn.) | Bassam Salim (Baker Hughes)
Wilson (TGT Oil and Gas Services) | Jamal Barghouti (TGT Oil and Gas Services) | Yulia Maslennikova
(TGT Oil and Gas Services) ABSTRACTS
Monitoring and handling Sustainable Annulus noise logs.[1] However, recent developments
ABSTRACTS Pressure (SAP) is a daily challenge in today’s in temperature and noise logging tools and
Spectral Noise Logging (SNL) can provide casing channels and wellbore completion oil and gas industry. Well integrity failure can interpretive techniques have been rewarded by
information on reservoir flow units behind components. affect production and the environment and, achieving high resolution and sensitivity enabling
one or multiple barriers, which is beyond the Thorough analysis of active flow streaks helps to consequently, lead to high economic losses the detection of previously undetectable leaks.
spinner capability. The SNL tool is designed to monitor sweep efficiency and identify bypassed from fixing the resulting damage. Once SAP is [2] This paper describes two cases of integrity
record a high-resolution noise pattern in a wide oil regions. confirmed, its source should be located and shut failure in the B and C annuli detected by the
frequency range, normally generated by fluid Reservoir matrix flow noise remarkably off as soon as possible. The biggest problem is new integrated high-precision temperature and
or gas flowing through porous media and the correlates with porosity distribution. Therefore, leaks behind multiple barriers, which are not spectral noise logging technique, or HPT-SNL.
wellbore. Noise pattern recognition is critical it is an effective way to verify porosity and clearly seen in conventional temperature and
to differentiate between formation flow and permeability models. This paper presents
wellbore flow. five field cases of SNL surveys performed
SNL complements conventional production during 2009–2011 in wells operated by Dubai
logging techniques by providing significant Petroleum Establishment. These cases illustrate
information that enhances reservoir flow the allocation of injection by zone with rates
characterisation. The tool design, data below the spinner threshold, evaluation of
acquisition and advanced processing allow the the reliability of plugged perforations, and
location of active flow units and differentiation description of the behindpipe flow geometry.
between flows through the reservoir matrix, The paper also contains an introduction to
fractures, high-permeability features, behind- SNL tool operation and noise data processing
principles.
20. INTEGRATING RESERVOIR MODELLING, HIGH-PRECISION TEMPERATURE LOGGING AND 21. INNOVATIVE LOGGING TOOL USING NOISE LOG AND HIGH PRECISION TEMPERATURE
SPECTRAL NOISE LOGGING FOR WATERFLOOD ANALYSIS HELP TO DIAGNOSES COMPLEX PROBLEMS
NUMBER NUMBER
SPE-157149-MS SPE-161712-MS
AUTHORS AUTHORS
Ayesha Rahman Al Marzouqi (Abu Dhabi Co. Onshore Oil Opn.) | Ashraf Al-saiid Keshka (Abu Dhabi Co. Salim Ghalem (Abu Dhabi Marine Operating Co.) | Amr Mohamed Serry (Abu Dhabi Marine Operating
Onshore Oil Opn.) | Jamal Nasir Bahamaish (Abu Dhabi Co. Onshore Oil Opn.) | Arthur Aslanyan (TGT Co.) | Ali Al-felasi (Abu Dhabi Marine Operating Co.) |Ahmed Berrim (Abu Dhabi Marine Operating Co.)
Oil & Gas Services) | Irina Aslanyan (TGT Oil & Gas Services) | Maxim Filenev (Kazan State University) | Osama Mohamed Keshtta(Abu Dhabi Marine Operating Co.) | Maxim Filenev (Kazan State University)
|Alexey Andreev (TGT Oil & Gas Services) | Vladislav Sudakov | Rushana Farakhova | Jamal Barghouti |Elyes Draoui (Abu Dhabi Marine Operating Co.) | Ayman Mohamed (ADMA-OPCO) | Hicham Abu
(TGT Oil Co.) | Tariq Abdulla Al Junaibi (ADCO Producing Co. Inc.) Chaker (ADMA-OPCO) | Alfiya Gabdrakhmanova (TGT Oil and Gas Services) | Arthur Aslanyan (TGT Oil
and Gas Services)
ABSTRACTS
Today, geological and hydrodynamic models reservoirs units F1 and F2 and the objective of ABSTRACTS
are widely used for efficient development and this pilot is to identify the flow geometry in wells’ Abu Dhabi’s mature field with more than 50 works and optimum workovers and future
monitoring of oil and gas fields. These models neighborhood, particularly identify channeling, years of production history and over 350 wells wells drilling, which all expected to enhance oil
are designed to handle a wide range of tasks. fracture flows or other types of communication. that is presented in this paper is one of the recovery.
Their reliability directly affects the quality of The objective of the associated simulations and world’s largest offshore oil fields. As oil fields This paper introduces an innovative logging
results and any uncertainties should, therefore, study is to correlate the acquired and interpreted mature, water and gas breakthroughs become technique designed to track fluid movement
be minimised. The use of additional techniques data with those suggested by simulations and increasingly frequent and the understanding deep in the formation in flow and no-flow
can enhance the reliability and predictive ability come up with consistent description of reservoir of fluid movement becomes crucial for proper intervals and through casing.
of the models and minimise risks. This paper flow geometry within the pilot pattern. reservoir management, efficient remedial
describes how integrating accurate description The most challenging point of this flooding
of flow geometry with reservoir properties campaign is the complexity of the reservoir in
and reservoir models to achieve this objective this area. The flooding pilot sets the targets
and, to generate a more reliable picture of the for tight Sub-reservoir carbonates Unit F1 and
reservoir performance. The study included Unit F2. It’s important to know if the flow
running HPT-PLT-SNL high precision logging ensues exactly within these units and does not
tools, and covered a pilot area with five wells communicate with other reservoirs with better
in a Cretaceous carbonate reservoir. The wells permeability.
were completed in the lower and tighter Sub-
22. MEMORY PULSED NEUTRON-NEUTRON LOGGING 23. MEMORY MAGNETIC IMAGING DEFECTOSCOPY
NUMBER NUMBER
SPE-162074-MS SPE-162054-MS
AUTHOR AUTHORS
Andrey Arbuzov Andrey Arbuzov
ABSTRACTS ABSTRACTS
This paper describes the MINK tool which is miss technique. The authors have developed This paper presents downhole magnetic imaging where as the long coil generates a long, high-
based on pulsed neutron-neutron (PNN) logging algorithms and software for the efficient and defectoscopy (MID) in memory mode, its key amplitude electromagnetic pulse and records
technology, its key principles and differences reliable determination of single- and double- principles, differences from other corrosion a signal travelling a much longer distance of up
from other logging and data interpretation exponential approximation parameters using logging technologies, and some results of its to 13 inches to record the total response from
methods, and illustrates its applications to the maximum likelihood method. application in oil wells. tubing and casing. Mathematical processing of
estimating oil saturation in wells. The processing of data from three selected The MID technology is designed to check the these responses can determine the thicknesses
The principal feature of the MINK tool is its data wells has shown that Sigma profiles determined integrity of magnetic and non-magnetic tubing of the first and second metal barriers.
recording technique in which all neutron-count by the least square method are noisier than and casing strings in oil and gas wells. It can be An independent power supply allows logging to
decays are saved to memory and processed those determined by the maximum likelihood used to detect various defects, corrosion and be performed on slickline, which substantially
separately. In conventional PNN logging, 100 method. Moreover, some thin reservoir units mechanical wear, and to assess the quality of reduces operating costs and enables the use
decays are initially accumulated and then were not seen in Sigma profiles obtained by perforations. of magnetic imaging defectoscopy for well
averaged before processing, which results in the least square method, in contrast to those The MID tool contains two high-sensitivity monitoring to prevent leak and corrosion related
information loss. obtained by the maximum likelihood method. sensors: a short generator/receiver coil and a incidents and thus increase environmental safety
Theoretical considerations and available Statistical modelling has been performed to long one with short relaxation times to analyse in the field. The wide use of memory magnetic
experimental data have indicated that the validate the developed algorithms. Decays with responses even at early times of 0.1 ms. The imaging defectoscopy will substantially reduce
probability distribution of neutrons is governed experimentally determined decay times and short coil generates a short, low-amplitude the number of well incidents and expenses for
by Poisson’s law [1] and allows the use of Poisson’s distribution of neutron count decays electromagnetic pulse and records a response remedial jobs.
the maximum likelihood method (MLM) for have been generated. Modelling data processing from the first metal barrier, normally tubing,
experimental data fitting [2] with a substantial has shown that the maximum likelihood method
advantage over the conventional least-square provides 1.7 to 2 times higher accuracy than the
method (LSM). This was particularly important least square method under equal conditions or
for reservoir characterisation, as the rock’s 3 to 4 times smaller data collection volumes.
response is mainly recorded at late times. The MINK technology is expected to determine
Neutron count rates at late times are small, and the oil content in dense reservoirs and low-
the least square method becomes a hit-and- salinity wellbore fluids.
24. REFINEMENT OF A GEOLOGICAL RESERVOIR MODEL BY DETAILED CORRELATION 25. SPECTRAL NOISE LOGGING DATA PROCESSING TECHNOLOGY
(RUSSIAN)
NUMBER
NUMBER SPE-162081-MS
SPE-162080-RU
AUTHORS
AUTHOR Yulia S. Maslennikova (TGT Prime) | V. V. Bochkarev (TGT Prime) | A. V. Savinkov (TGT Prime) | D. A.
Aliya Mubarakova (Almetyevsk State Oil Institute) | V. Sudakov (TGT Oil and Gas Services) | S. Sidorov Davydov (TGT Prime)
(TGT Oil and Gas Services)
ABSTRACTS
ABSTRACTS Rational development of oil and gas reservoirs broadband noise created by the movement of
It is very important to understand sedimentation The entire knowledge of region’s geology and is possible only with efficient monitoring by the tool in the well.
in detail, both from the aspect of geological or stratigraphy, and any available field data are various well logging techniques. This paper Useful information is extracted from
petrophysical modelling and field development. applied during the correlation and almost all presents algorithms for processing data background noise using a technique based on
The correctly inferred distribution of a applicable open-hole logging techniques are acquired by spectral noise logging (SNL) in wavelet thresholding. Spectral noise density in
stratigraphic layer’s boundaries pre-determines useful for the purpose of correlation. memory mode. The SNL technology is designed the depth-frequency plane undergoes a wavelet
the fluid flow produced by the model to be close The correlation itself is optimised, split into to identify flowing reservoir intervals, cross- transform. At each measurement depth, several
to the actual flow. Activities to enhance residual stages and sub-stages to save time and minimise flows behind casing and tubing and casing leaks tens of noise signals are recorded to determine
oil recovery are more effective if planned errors. by spectral analysis of recorded noise signals. mean wavelet coefficients and their typical
according to the detailed stratification, which While moving through a reservoir, fluids and variance. Then, they are analysed to remove
means understanding of the geologic aspects of gases create turbulence and rock vibrations statistically insignificant details from the signal
a single area. that in turn generate noise. This acoustic noise spectrum and to suppress noise components
is recorded with a noise logging memory tool that are present throughout large depth
consisting of a high-sensitivity piezoelectric intervals.
hydrophone sensor and an amplifier and data The processing of data acquired in tens of wells
collection module. The tool records acoustic from various fields has show that the noise
signals in the frequency range of 15 Hz to 60 kHz. features identified by wavelet filtering correlate
The existing SNL technology excludes intense with open-hole data and are confirmed by
conventional well logging techniques.
СHAPTER 4:
REFERENCES
1. M.A. Miheev, I.M. Miheeva. Foundations 12. S.A. Nikolaev and others, “Sound Generation
of heat transfer. In Russian, 1973, Moscow, by Percolation Flows through Porous Media”
Energiya Press. published in Acoustic Journal, 1992, 38, No.
2. H. Schlichting. Boundary-Layer Theory. In 1, 114–118 3
Russian, 1974, Moscow, Nauka Press. 13. Y.M. Zaslavsky, “On the Theory of Acoustical
3. V.E. Nakoryakov, A.V. Gorin. Heat and mass Emission Accompanying Gas Filtration by
transfer in two-phase systems. In Russian, Partially Fluid-Saturated Medium” published
1994, Novosibirsk, Institute of thermophysics in Technical Acoustics Electronic Journal,
of Siberian Branch of the Russian Academy http://ejta.org, 2005, 5
of Sciences Press. 431 pp. 14. M.J. Lighthill, “On Sound Generated
4. O. Bratland, Pipe flow 1. Single-phase Flow Aerodynamically: Turbulence as a Sound
Assurance Source”, 1954.
5. O. Bratland, Pipe flow 2. Multiphase Flow 15. Wang Y, Jin J, Bai B and Wei M, “Study of
Assurance Displacement Efficiency and Flow Behavior
6. A.M. Ansari, N.D. Sylvester, O. Shoham, J.P. of Foamed Gel in Non-Homogeneous Porous
Brill. A Comprehensive Mechanistic Model Media”, 2015, PLoS ONE 10(6): e0128414
for Upward Two-Phase Flow in Wellbores. 16. SPE 177620-MS Quantification of Reservoir
SPE Annual Technical Conference and Pressure in Multi-Zone Well under Flowing
Exhibition, 23-26 September, New Orleans, Conditions Using Spectral Noise Logging
Louisiana, 1990 Technique, Zubair Reservoir, Raudhatain
7. D.H. Beggs, J.P. Brill. A Study of Two-Phase Field, North Kuwait (2015)
Flow in Inclined Pipes. Journal of Petroleum 17. SPE 162081 Spectral noise logging data
Technology, vol. 25, 1973 processing technology (2012)
8. H. Shi, J.A. Holmes, L.R. Diaz, L.J. Durlofsky, 18. Arbuzov, A.A., Alekhin, A.P., Bochkarev,
K. Aziz. Drift-Flux Parameters for Three- V.V., Minakhmetova, R.N., Chukhutin, D.V.
Phase Steady-State Flow in Wellbores. SPE and Zakirov, A.N. Memory Pulsed Neutron-
Annual Technical Conference and Exhibition, Neutron Logging, SPE- 162074, SPE Russian
26-29 September, Houston, Texas, 2004 Oil & Gas Exploration & Production Technical
9. H. Shi, J.A. Holmes, L.J. Durlofsky, K. Aziz, L.R. Conference and Exhibition, Moscow, Russia,
REFERENCES
Diaz, B. Alkaya, G. Oddie. Drift-Flux Modeling October 16–18, 2012
СHAPTER 4:
of Multiphase Flow in Wellbores. SPE Annual 19. Williams M.M.R. Effective diffusion
Technical Conference and Exhibition, 5-8 coefficients in heterogeneous media. J. Nucl.
October, Denver, Colorado, 2003 Energy, v.26, pp. 189-209, 1972.
10. Y. Nicolas, E.J. Witterholt. Measurements of 20. Crain, E.R., “Crain’s Petrophysical Handbook.,
Multiphase Fluid Flow. Fall Meeting of the at http://www.spec2000.net, Rocky
Society of Petroleum Engineers of AIME, Mountain House, Alberta, Canada, 2013
8-11 October, San Antonio, Texas, 1972 21. TERMOSIM Software (https://tgtoil.
11. Hinze, J.O. 1959. Turbulence, McGraw-Hill com/technologies/hpt-high-precision-
Book Co., Inc., New York temperature-logging/itsm/)
22. Salamatin A., Karuzin A., Aslanyan I., Zaripov High-Precision Temperature and Spectral
I. TERMOSIM Handbook – Kazan, Russia: TGT Noise Logging Techniques. SPE-171251-
Oil And Gas Services, 2014. – 320 (https:// MS presented at the SPE Russian Oil and
www.prime-college.ru/courses/tgt/level/ Gas Exploration and Production Technical
advanced/wla-advanced/rfa-2/rfa-i/rfa-i- Conference and Exhibition held in Moscow,
mc/) Russia, 14-16 October.
23. Nikolaev S., Nikolaeva N., Salamatin A. 27. Arthur Aslanyan, Irina Aslanyan, Andrey
Thermal physics of rocks. – Kazan: KSU , Salamatin, Andrey Karuzin, Yulia Fesina et al.
1987. – 152 p. 2014. Numerical Temperature Modelling for
24. Nelson Suarez, Ademola Otubaga Quantitative Analysis of Low-Compressible
and Nagendra Mehrotra et al. 2013. Fluid Production. SPE 172090 presented
Complementing Production Logging with at the Abu-Dhabi International Petroleum
Spectral Noise Analysis to Improve Reservoir Exhibition and Conference held in Abu-
Characterisation and Surveillance. SPWLA 54 Dhabi, UAE, 10–13 November.
th Annual Symposium held in New Orleans, 28. A. Aslanyan, I. Aslanyan, A. Arbuzov, B.
Louisiana, USA, 22-26 June. Zagidullin et al. 2014. Time-Domain Magnetic
25. Salim Ghalem, D. Elyes Draoui, Ayman Defectoscopy for Tubing and Casing Corrosion
Mahamed et al. 2012. Innovative Noise and Detection. SPE 169601 presented at the SPE
High-Precision Temperature Logging Tool International Oilfield Corrosion Conference
for Diagnosing Complex Well Problems. and Exhibition held in Aberdeen, United
SPE-161712 presented at the Abu-Dhabi Kingdom, 12–¬13 May 2014.
International Petroleum Exhibition and 29. Ihab, N. M., El-Hamawi, M, Rasheed A.H.
Conference held in Abu-Dhabi, UAE, 11–14 Arthur, A.A, Filenev, M, Aslanyan I.Yu,
November. Bargouthi J., Salim,B,. Leak Detection By
26. A.A. Lutfullin, A.R. Abdrahimov, I.N. Shigapov, Temperature And Noise Logging. 2012. Abu
I.Yu. Aslanyan, A.M. Aslanyan, R.K. Kuzyutin Dhabi International Petroleum Exhibition
et al. 2014. Identification of Behind-Casing & Conference, Abu Dhabi, UAE, 11-14
Flowing Reservoir Intervals by the Integrated November.