MAA-TGAC-ANC-CALC-00015 Rev.0
MAA-TGAC-ANC-CALC-00015 Rev.0
MAA-TGAC-ANC-CALC-00015 Rev.0
Enclosure:
Pre-Qualification of Subcontractor Calculation Project Quality Plan/Procedures Certificate Material Subm.
Test Results Sketch Project Safety Plan Guarantee Others
Consultant's Comments:
A - Approved
B - Approved As Noted
C - Not Approved
DUBAI, U.A.E
EXT-W656-TS-CAL-02
REV 00
06/02/2023
Page 1 of 43
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
TABLE OF CONTENTS
6 Limits of Deformation 7
Appendix-4 Drawings 40
Page 2 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
1. INTRODUCTION:
The calculation will verify the adequacy of GFRC FRAME CLADDING [GRC CANOPY] (For Conservative
design we considered worst case scenario for all panel and its supporting steel brackets in withstanding
the applied design loads as per project specification & design standards.
2. DESIGN:
Generally, all the design has been carried out in accordance with relevant Standards with a particular
reference to the following codes of practice.
- PCI MNL 128 Recommended Practice for Glass Fibre Reinforced Concrete Panels – for Load
Factors, Load Combinations& Deflection.
- CEM-FIL GRC Technical Data.
- "Practical Design Guide" for GRC Prepared by International GRCA Technical Committee.
- Specification for Structural Steel Buildings (ANSI/AISC 360-10) - 2010.
- BS 5950 as per Design Specifications – for the design of Steel Sections and Fixings.
- BS 6399, BS 6180 and BS EN 1991: Part 1-1 for Live Load as per Specifications.
- ASCE 7 -05 Minimum Design Loads for Buildings and other structures.
- IBC 2009 International building code for calculating Seismic Force for Cladding Components.
- Design of Stainless-Steel connection based on "SCI 291 Structural Design of Stainless Steel".
3. MATERIAL PROPERTIES:
- Steel Sections and Brackets – All connection plates and built-up sections to be used are
Min of S275JR grade (GI) PẎ=275Mpa and Fu=450Mpa.
- All bolts used as panel rod are Grade SS316-(A4-70) bolts having minimum grade of Fyb = 450Mpa and
Fub =700Mpa
Page 4 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
4.LOADS
4.LOADS
a) DEAD LOAD:
- Weight of Glass Fibre Reinforced Concrete (GRC)
- The weight of the GRC panel will be calculated by STAAD Pro by the use of Self weight
command.
b) WIND LOAD:
The design wind pressure is calculated according to ASCE 7-16[C/C-Canopy Structures & Wall Cladding]
-Refer to Appendix-3 for detailed wind load calculation with reference sheets.
5. LOADS AND LOAD COMBINATIONS (GFRC PANEL AS PER PCI MNL 128):
Page 5 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
4. 1.0DL + 1.0WL1
5. 1.0DL + 1.0WL2
-Note that we used load factors and combinations according to PCI MNL 128 "Recommended Practice
for Glass Fiber Reinforced Concrete Panels", as per Section 034900-GFRC of the Global Project
Specifications.
4. 1.0DL + 1.0WL1
5. 1.0DL + 1.0WL2
Page 6 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
6. 1.4 DL
6. DEFLECTION LIMIT:
FOR GRC PANEL:
According to PCI MNL 128 (5.5) deflection due to service loads are limited to L/240.
Page 7 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
APPENDIX -1
Page 8 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
Page 9 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
12mm GRC Skin thickness has been assigned in the highlighted modelled plates
ASSIGNMENT OF LOADS:
Note: As per GRC Laboratory Tests of Extra Co allowable Flexural Yield Strength Varies from 7Mpa to
11Mpa [Test Result Attached]. For Conservative design we are checking the panel for minimum flexural
strength of 6.2 Mpa.
Page 12 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
Maximum Von Mis Stress @ Ultimate = 2.34 N/mm2 (as per attached contour for load case 7
(1.2 DL + 1.6 WL1).
Page 13 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
Page 14 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
APPENDIX -2
Page 15 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
Job No Sheet No Rev
1
Part
Software licensed to
Job Title Ref
By Date06-Feb-23 Chd
Job Information
Engineer Checked Approved
Name:
Date: 06-Feb-23
Project ID
Project Name
Combination 6 1.4 DL
Combination 7 1.2 DL + 1.6 WL1
Combination 8 1.2 DL + 1.6 WL2
Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 CH100X50X10 13.000 32.300 208.000 2.428 STEEL
2 C75X40X5 8.818 12.200 75.300 1.198 STEEL
Print Time/Date: 06/02/2023 16:42 STAAD.Pro V8i (SELECTseries 6) 20.07.11.45 Print Run 1 of 7
Page 16 of 43
Job No Sheet No Rev
2
Part
Software licensed to
Job Title Ref
By Date06-Feb-23 Chd
0.300m
Y
X
Z Load 3
Print Time/Date: 06/02/2023 16:42 STAAD.Pro V8i (SELECTseries 6) 20.07.11.45 Print Run 2 of 7
Page 17 of 43
Job No Sheet No Rev
3
Part
Software licensed to
Job Title Ref
By Date06-Feb-23 Chd
CH100X50X10
0.360m
CH100X50X10
CH100X50X10
CH100X50X10
CH100X50X10
CH100X50X10
C75X40X5
C75X40X5
0.300m
C75X40X5
Y
X
Z C75X40X5 Load 3
C75X40X5
C75X40X5
SECTION PROPERTY
-0.208 kN
0.019-0.208
kN kN
0.019 kN
-0.208 kN
0.019-0.208
kN kN
0.019 kN
-0.674 kN
-0.674 kN
-0.019 kN
-0.674 kN
-0.019 kN
-0.674 kN
Y
X
Z Load 1
-0.019 kN
-0.019 kN
DEAD LOAD(DL)
Print Time/Date: 06/02/2023 16:42 STAAD.Pro V8i (SELECTseries 6) 20.07.11.45 Print Run 3 of 7
Page 18 of 43
Job No Sheet No Rev
4
Part
Software licensed to
Job Title Ref
By Date06-Feb-23 Chd
-0.482 kN
-0.394 kN
-0.181 kN
0.331 kN
-0.230 kN
0.893 kN
-0.482 kN
-0.394 kN
-0.181 kN
0.331 kN
-0.230 kN
0.893 kN
-0.131 kN
0.409 kN
0.131 kN kN
-0.275
0.905 kN
Y
X -0.131 kN
Z Load 2
0.409 kN
0.131 kN kN
-0.275
0.905 kN
-0.331 kN
0.181 kN -0.893 kN
0.230 kN
0.482 kN
0.394 kN
-0.331 kN
0.181 kN -0.893 kN
0.230 kN
0.482 kN
0.394 kN
-0.409 kN
-0.905 kN
0.275
0.131 kNkN kN
-0.131
Y
X -0.409 kN
Z -0.905 kN Load 3
0.275
0.131 kNkN kN
-0.131
Print Time/Date: 06/02/2023 16:42 STAAD.Pro V8i (SELECTseries 6) 20.07.11.45 Print Run 4 of 7
Page 19 of 43
Job No Sheet No Rev
5
Part
Software licensed to
Job Title Ref
By Date06-Feb-23 Chd
Print Time/Date: 06/02/2023 16:42 STAAD.Pro V8i (SELECTseries 6) 20.07.11.45 Print Run 5 of 7
Page 20 of 43
Job No Sheet No Rev
6
Part
Software licensed to
Job Title Ref
By Date06-Feb-23 Chd
Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 C75X40X5 C75X40X5 0.280 1.000 0.280 Eq. H1-1b 8 8.818 75.300 12.200 1.200
2 CH100X50X10CH100X50X10 0.183 1.000 0.183 Eq. H1-1b 7 13.000 208.000 32.300 2.510
5 C75X40X5 C75X40X5 0.237 1.000 0.237 Eq. H1-1b 8 8.818 75.300 12.200 1.200
6 C75X40X5 C75X40X5 0.000 1.000 0.000 Sec. G1 6 8.818 75.300 12.200 1.200
7 CH100X50X10CH100X50X10 0.111 1.000 0.111 Eq. H1-1b 7 13.000 208.000 32.300 2.510
8 CH100X50X10CH100X50X10 0.000 1.000 0.000 Sec. G1 6 13.000 208.000 32.300 2.510
9 C75X40X5 C75X40X5 0.280 1.000 0.280 Eq. H1-1b 8 8.818 75.300 12.200 1.200
10 CH100X50X10CH100X50X10 0.183 1.000 0.183 Eq. H1-1b 7 13.000 208.000 32.300 2.510
11 C75X40X5 C75X40X5 0.237 1.000 0.237 Eq. H1-1b 8 8.818 75.300 12.200 1.200
12 C75X40X5 C75X40X5 0.000 1.000 0.000 Sec. G1 6 8.818 75.300 12.200 1.200
13 CH100X50X10CH100X50X10 0.111 1.000 0.111 Eq. H1-1b 7 13.000 208.000 32.300 2.510
14 CH100X50X10CH100X50X10 0.000 1.000 0.000 Sec. G1 6 13.000 208.000 32.300 2.510
0.183
0.111
5.65e-005
0.183
0.111
5.65e-005
0.28
0.237
4.26e-005
Y
X
Z 0.28 Load 3
0.237
4.26e-005
Print Time/Date: 06/02/2023 16:42 STAAD.Pro V8i (SELECTseries 6) 20.07.11.45 Print Run 6 of 7
Page 21 of 43
Job No Sheet No Rev
7
Part
Software licensed to
Job Title Ref
By Date06-Feb-23 Chd
Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
Max FX 1 8:1.2 DL + 1.6 WL2 2.102 1.642 -0.394 -0.302 0.418 0.000
Min FX 1 7:1.2 DL + 1.6 WL1 -2.102 1.642 0.486 -0.199 -0.418 0.000
Max FY 3 7:1.2 DL + 1.6 WL1 -1.958 1.944 0.612 -0.400 -0.524 0.000
Min FY 3 8:1.2 DL + 1.6 WL2 1.958 -0.859 -0.703 0.170 0.524 0.000
Max FZ 3 7:1.2 DL + 1.6 WL1 -1.958 1.944 0.612 -0.400 -0.524 0.000
Min FZ 3 8:1.2 DL + 1.6 WL2 1.958 -0.859 -0.703 0.170 0.524 0.000
Max MX 3 8:1.2 DL + 1.6 WL2 1.958 -0.859 -0.703 0.170 0.524 0.000
Min MX 3 7:1.2 DL + 1.6 WL1 -1.958 1.944 0.612 -0.400 -0.524 0.000
Max MY 3 8:1.2 DL + 1.6 WL2 1.958 -0.859 -0.703 0.170 0.524 0.000
Min MY 3 7:1.2 DL + 1.6 WL1 -1.958 1.944 0.612 -0.400 -0.524 0.000
Max MZ 1 6:1.4 DL 0.000 1.916 0.053 -0.292 0.000 0.000
Min MZ 1 6:1.4 DL 0.000 1.916 0.053 -0.292 0.000 0.000
Print Time/Date: 06/02/2023 16:42 STAAD.Pro V8i (SELECTseries 6) 20.07.11.45 Print Run 7 of 7
Page 22 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Input data
Anchor type and size R-KERII+R-STUDS-10130-A4FL
High performance resin for use with metric threaded rods -
steel grade A4-70
Nominal depth (hnom) 60 mm (hef = 60 mm)
Base material Cracked concrete (C20/25) Temp. short/long None
Reinforcement No reinforcement
Longitudinal edge reinf. Without edge reinforcement or stirrups
Installation Hammer drilling, Installation conditions: Dry concrete
Lever arm None
Fixture Baseplate (x=200 mm, y=125 mm)
Declared thickness: tfix = 10 mm
Recommended thickness: 7 mm (Calculated)
Material: S275 (acc. to S275) fyk=275 MPa, γ=1.1
Steel profile PFC 100x50x10 (h=100 mm, b=50 mm)
Proof EOTA TR029
ETA-21/0242 v.11/03/2021
Working life of 50 years
Design loads
N 710 N
Mx 530 Nm
My 400 Nm
Vx 1.95 kN
Vy 2.11 kN
Ms 0 kNm
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 23 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Anchor N V Vx Vy
Steel failure
βN1 = 14.3%
calculated for anchor: 3
22.12 kN 6.64 kN
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 24 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 25 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Utilisation
- According to the current guidelines for the design of anchorages, the calculations in EasyFix4 base on the assumption
that the base plate is rigid, which means that redistribution of loads on the anchors due to elastic deformation of the base
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 26 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
plate is not taken into account. In the software, the recommended thickness of the base plate can be determined, however
the correctness of the installation of the rigid base plate must be checked and confirmed separately.
- The size of the holes in the base plate must not be larger than it is allowed in the table with installation parameters.
Otherwise, all gaps in the holes between the anchors and the fixed element must be filled, e.g. by filling the gaps with
resin of adequate compressive strength.
- Preparation of holes and installation of fasteners must be performed in accordance with the installation instruction,
taking into account the entered input data.
- The information and data contained in EasyFix4 apply only to Rawlplug products. The results of the calculations carried
out with the use of the Software are based on data entered by the User, who is exclusively responsible for the correctness
of the input data and any errors. In addition, the User is exclusively responsible for the verification and recognition of the
calculation results by a competent person, in particular with regard to compliance with applicable standards and
regulations.
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 27 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Fixture shape
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 28 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Input data
Anchor type and size R-KERII+R-STUDS-10130-A4FL
High performance resin for use with metric threaded rods -
steel grade A4-70
Nominal depth (hnom) 60 mm (hef = 60 mm)
Base material Cracked concrete (C20/25) Temp. short/long None
Reinforcement No reinforcement
Longitudinal edge reinf. Without edge reinforcement or stirrups
Installation Hammer drilling, Installation conditions: Dry concrete
Lever arm None
Fixture Baseplate (x=140 mm, y=100 mm)
Declared thickness: tfix = 10 mm
Recommended thickness: 7 mm (Calculated)
Material: S275 (acc. to S275) fyk=275 MPa, γ=1.1
Steel profile (h=75 mm, b=40 mm)
Proof EOTA TR029
ETA-21/0242 v.11/03/2021
Working life of 50 years
Design loads
N 710 N
Mx 0 kNm
My 400 Nm
Vx 1.95 kN
Vy 2.11 kN
Ms 530 Nm
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 29 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Anchor N V Vx Vy
Steel failure
βN1 = 10.3%
calculated for anchor: 1
12.59 kN 4.68 kN
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 30 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 31 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 32 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Utilisation
- According to the current guidelines for the design of anchorages, the calculations in EasyFix4 base on the assumption
that the base plate is rigid, which means that redistribution of loads on the anchors due to elastic deformation of the base
plate is not taken into account. In the software, the recommended thickness of the base plate can be determined, however
the correctness of the installation of the rigid base plate must be checked and confirmed separately.
- The size of the holes in the base plate must not be larger than it is allowed in the table with installation parameters.
Otherwise, all gaps in the holes between the anchors and the fixed element must be filled, e.g. by filling the gaps with
resin of adequate compressive strength.
- Preparation of holes and installation of fasteners must be performed in accordance with the installation instruction,
taking into account the entered input data.
- The information and data contained in EasyFix4 apply only to Rawlplug products. The results of the calculations carried
out with the use of the Software are based on data entered by the User, who is exclusively responsible for the correctness
of the input data and any errors. In addition, the User is exclusively responsible for the verification and recognition of the
calculation results by a competent person, in particular with regard to compliance with applicable standards and
regulations.
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 33 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 34 of 43
EasyFix4 v. 4.8.2 - Concrete 2128e2458
Fixture shape
Page
National regulations, environmental and application conditions must be considered when designing the anchorage. 35 of 43
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
Page 36 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
APPENDIX -3
Page 37 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
Design Wind Pressure p = qh[(GCp) - (GCpi)] [From Eq 6.22; 6.5.12.4.1 Buildings with h (8m) < 18.3m]
Where,
Velocity Pressure Exposure Co-efficient, Kz = 1.13 [From Sec;6.5.6.6(Page-26 & Table 6-3]
Effective Wind Area of Panel Ea = Minimum Considered for Worst Case Scenario
External Pressure Co-efficient GCp zone4 = +1, -1.4 (maximum of Zone 4 & 5 [From Fig; 6-11A]
Velocity Pressure qz = 0.613 Kz Kzt Kd V2 I = 0.613 x 1.13 x 1.0 x 0.85 x (45)2 x 1.0 = 1.2 kN/m2
Page 38 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
EXTRA CO INDUSTRIES L.L.C
Precast Business Unit, PO. Box-21391, RAK, U.A.E.
Design Wind Pressure ppositive = qh [(GCp) - (GCpi)] = 1.2[(1) – (0)] = 1.2 kN/m2
Design Wind Pressure pnegative = qh [(GCp) - (GCpi)] = 1.2[(-1.4) – (0)] = -1.68 kN/m2
Where,
GCp = Net pressure coefficient (From Figure 30.11-1A, 30.11-1B of ASCE 7-16) = -1.4, +0.9
For Conservative Design we will consider maximum wind force on both directions as 1.75 kN/m2 on
Page 39 of 43
EXT-W656-TS-CAL-02| Rev. 00|6th FEB 2023
TECHNICAL SUBMITTAL
Project: 2020 – MARSA AL ARAB Ref. No.:
300-ANC-ASGC-ARC-SDG-
004823-R1
Contract: P300/CA/ASGC-KILLA/105/21 Date:
Shop Drawing for Ancillaries Entrance Gate House GRC Indicated Elevations, GRC Indicated Plan & Section Details, GRC
Description: Blowup Details - D1 To D8 Attention:
BIM – Building Information Model MES – Method Statement SCH – Schedule Submittal Code:
CAL – Calculation MND – Manufacturers Data SHD – Shop Drawing 1 – Approval
CER – Certificate MRP – Monthly Report SSB – Sample Submittal 2 – Information
COS – Compliance Statement OTH – Others TED – Technical Data
Type code: DOC – Document PPL – Proposal TNS – Technical Submittal
DRP – Daily Report PRQ – Pre-Qualification TRP – Test Reports
DWG – Drawings SAM – Samples WAR – Weekly Report
GUA – Guarantee SAR – Site Accident Report WRP – Warranty
MAS – Material Submittal
A – Approved B – Approved as noted C – Not approved/Resubmit D – Rejected
Status code: (Work can proceed) (Work can proceed incorporating the comments) (Revise & Resubmit)
Sr. Doc Ref. Rev. Rev date Description Type Submittal Status
No. code code code
(by KLD)
1.
2.
3.
4.
5.
6.
KLD Representative:
Name: MH(KLD) Signature: Date:
Received by (Contractor):
Name: Signature: Date:
Corrections or comments made relative to submittals during this review do not relieve the contractor from compliance with the contract requirements and
specifications. This check is only for review of general conformance with the design concept of the project and general compliance with the information
given in the contract documents and no time and/or cost implication shall be granted due to the Engineer 's /PM instruction.
Page 40 of 43
Form no.KLD-SF31/CPL/15-Sep-2019/Rev.0 Page 1 of 1
S4
1 2 A B
KLD ARC: ALL
BRACKETS MUST
S1 BE CONCEALLED
ROOF TOW ROOF TOW
8.625 m FFL 8.625 m FFL
KLD ARC:
KEY PLAN:
EIFS cladding - White APPROVAL IS ONLY
RAL 9003 FOR GRC PANELS, 12 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 35
36 38 40 41
37 39
42 43 44 45 46 47 48 49 50 51 52 53 54 56 57
55
DOORS ARE TO BE
H
REVIEWED AND T S
U V
W
X
EIFS cladding - White RAL 9003 Stone Tiles Steps to match IFC-FACADE MAA-INH-AN01-AF-SE-GF-0010 00
Stone Tiles from Landscape LEGEND
Stone Tiles Steps to match
Stone Tiles from Landscape
GROUND FLOOR LEVEL GROUND FLOOR LEVEL
5.000 m FFL 5.000 m FFL
Date:
ROOF TOW ROOF TOW Inhabit ME
Inhabit AsiaLimited
ME
02/11/2022
8.625 m FFL 8.625 m FFL
S3
PROJECT MANAGEMENT:
EIFS cladding - White RAL 9003
Drawing
Title: ANCILLARIES
ENTRANCE GATE HOUSE
GRC INDICATED ELEVATIONS
1 OF 3
26/10/2022 AR MRN A1
AR FC 00 of 43
Page 41 2001
KLD ARC: ALL
BRACKETS MUST KLD ARC:
BE CONCEALLED APPROVAL IS ONLY
FOR GRC PANELS,
LOUVERS AND
D1 DOORS ARE TO BE
REVIEWED AND
APPROVED
SEPARATELY
F S F S
A A
KEY PLAN:
HOUSE HOUSE
B
C
D
E
F
G
H
770020
770020
770025 770025
GF-001 GF-001
770020
770020
770025 770025
K
L
270281
270281
M
N
770014
770014
P
4.25 m² 4.25 m² Q
T S
U V
W
X
MAA2 MAA1
+5.000 FFL STAFF TOILET +5.000 FFL STAFF TOILET
GF-002 GF-002 GENERAL NOTES:
+4.900 SSL +4.900 SSL
1.70 m² 1.70 m²
OUTSIDE
OUTSIDE
1- ALL DIMENSIONS ARE IN MILLI METERS UNLESS NOTED
OTHERWISE. DIMENSIONS SHALL NOT BE OBTAINED BY
SCALLING DRAWINGS
7700 14
7700 14
770025
770025
270281 270281
270281
770020
770020
770025 770025
7700 14 770014
14 14
770020
770020
770025 770025
DRAWING REFERENCES
DESCRIPTION DWG. REF. No REV
B B
SHOP DRAWING REVIEW
The following document has been reviewed in terms of
technical content. This does not include dimensional
ARCHITECTURAL MAA-KLD-AN01-AR-GA-ZZ-1001 04
checking or checking of quantities. It also does not ARCHITECTURAL MAA-KLD-AN01-AR-EL-XX-2001 04
include checking associated information that is not
called up on the drawing.
D2 IFC-FACADE MAA-INH-AN01-AF-DE-GF-0213 00
IFC-FACADE MAA-INH-AN01-AF-DE-GF-0212 00
P IFC-FACADE MAA-INH-AN01-AF-DE-GF-0211 00
IFC-FACADE MAA-INH-AN01-AF-DE-GF-0210 00
A. Accepted
A. B. Accepted
B. C. Accepted
C. – D.D.Not
Approved Subject
Approvedto Subject
Rejectedto Accepted
For – IFC-FACADE MAA-INH-AN01-AF-SE-GF-0010 00
Comment
with - No Comment Resubmit /
Information
Comments Not in Scope
Resubmission Resubmit
LEGEND
MH(KLD)
1 2 2 A B
+8.675 TOW
ROOF LELEL ROOF LELEL ROOF LELEL ROOF LELEL
8.625 m 8.625 m 8.625 m 8.625 m
D4 D7
D3
MARSA AL ARAB
CLIENT:
770025
770020
770025
- All fixing
270281
770014
200015
subject to
PROJECT MANAGEMENT:
approved
GRC BOTTOM
structural GRC BOTTOM
calculation.
UPN 100 UPN 100
6.625 m (AN-01) 6.625 m (AN-01)
- All steel
finishes should
MAIN CONTRACTOR (DESIGN& BUILT):
be in accordance DF- 07
AN010203GF03 Level 5, Building 13, Bay Square.
SUB CONTRACTOR
EXTRA CO
INDUSTRIES L.L.C
Precast Business Unit
www.extraco.ae TEL. : +971-7-2589339 | FAX : +971-7-2589073
[email protected] PO.Box 21391, RAK, U.A.E. | [email protected]
Drawing
Title: ANCILLARIES
ENTRANCE GATE HOUSE
GROUND FLOOR LELEL HSA-M8x92/27/40
GROUND FLOOR GROUND FLOOR GRC INDICATED PLAN & SECTION DETAILS
5.000 m FFL 5.000 m FFL GROUND FLOOR LEVEL 5.000 m FFL 2 OF 3
TYP FFL
Scale: Plot No./Area:
As PLOT NO:- 3660492
indicated
Date: Drawn By: Checked By: Format:
26/10/2022 AR MRN A1
AR FC 00 of 43
Page 42 2002
This bolt will not
work in block wall
Indicate Material
Indicate Material
KEY PLAN:
12 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 35
36 38 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 56 57
37 39 55
A
B
C
D
E
F
G
H
J
K
L
show dimension
Q
T S
U V
of this panel W
X
MAA2 MAA1
GENERAL NOTES:
1- ALL DIMENSIONS ARE IN MILLI METERS UNLESS NOTED
OTHERWISE. DIMENSIONS SHALL NOT BE OBTAINED BY
SCALLING DRAWINGS
2- ALL LEVELS SHOWN ARE IN METERS.
3- LEVEL 0.000 = 0.000 DMD
DRAWING REFERENCES
DESCRIPTION DWG. REF. No REV
KLD ARC: PLEASE
CLARIFY, DESIGN
DRAWINGS SHOW
THE ENTIRE SHELF
D1 BLOW UP DETAIL D3 BLOW UP DETAIL IS GRC D4 BLOW UP DETAIL ARCHITECTURAL
ARCHITECTURAL
MAA-KLD-AN01-AR-GA-ZZ-1001
MAA-KLD-AN01-AR-EL-XX-2001
04
04
IFC-FACADE MAA-INH-AN01-AF-DE-GF-0213 00
IFC-FACADE MAA-INH-AN01-AF-DE-GF-0212 00
PERFORATED TOP
IFC-FACADE MAA-INH-AN01-AF-DE-GF-0211 00
PANEL IS NOT IFC-FACADE MAA-INH-AN01-AF-DE-GF-0210 00
ACCEPTABLE IFC-FACADE MAA-INH-AN01-AF-SE-GF-0010 00
LEGEND
UPN 100
approved
structural UPN 100
calculation.
- All steel
PROJECT MANAGEMENT:
finishes should MH(KLD)
be in accordance
with corrosion
protection table
in specification
MAIN CONTRACTOR (DESIGN& BUILT):
[ie...C5-m (H0)] D6 BLOW UP DETAIL Level 5, Building 13, Bay Square.
Bussiness Bay P.O. Box 13164, Dubai,
Tel (+971) 4 425 8097,
Fax (+971) 4 425 8060
SHOP DRAWING REVIEW www.asgcgroup.com
SUB CONTRACTOR
7.800 m (AN-01)
P EXTRA CO
INDUSTRIES L.L.C
Precast Business Unit
A. Accepted
A. B. Accepted
B. C. Accepted
C. – D.D.Not www.extraco.ae
[email protected]
TEL. : +971-7-2589339 | FAX : +971-7-2589073
PO.Box 21391, RAK, U.A.E. | [email protected]
Approved Subject
Approvedto Subject
Rejectedto Accepted
For –
GROUND FLOOR LEVEL Comment
with - No Comment Resubmit /
Information
Comments Not in Scope
TYP FFL Resubmission Resubmit PROJECT NO: ASGC-300
Stage:
SD
Name: Drawing
Title: ANCILLARIES
AG ENTRANCE GATE HOUSE
GRC BLOWUP DETAILS - D1 TO D8
3 OF 3
26/10/2022 AR MRN A1
AR FC 00 of 43
Page 43 2003