Professional Documents
Culture Documents
Obsolete: FT8U245AM
Obsolete: FT8U245AM
FEATURES
• Single Chip Fast Data Transfer Solution • UHCI / OHCI Compliant
• Send / Receive Data over USB at up to 1 M • USB 1.1 Specification Compliant
Bytes / sec • USB VID, PID, Serial Number and Product
• 384 byte FIFO Transmit buffer / 128 byte FIFO Description Strings in external E2PROM.
receive buffer for high data throughput Virtual COM Port Drivers for –
• Simple interface to CPU or MCU bus Windows 98 and Windows 98 SE
• No in-depth knowledge of USB required as all Windows 2000
USB Protocol is handled automatically within Windows Millennium **
the I.C. Apple iMAC **
• FTDI’s Virtual COM port drivers eliminate the Linux **
E
need for USB driver development in most • Application Areas
T
cases. USB ISDN and ADSL Modems
Ù PDA Communications
E
• Compact 32 pin ( 7mm x 7mm ) MQFP package High Speed USB
L
• Integrated 6MHz - 48MHz Clock Multiplier aids USB I/F for Digital Cameras
FCC and CE compliance USB I/F for MP3 players
O
• Integrated 3.3v Regulator – No External High Speed USB Instrumentation
Ù USB data transfer cables
S
Regulator Required USB
USB Ù USB null-modem cables
B
• 4.4v .. 5.25v Single Supply Operation
O
GENERAL DESCRIPTION
The FT8U245AM provides an easy cost-effective method of transferring data to / from a peripheral and a
host P.C. at up to 8 Million bits ( 1 Megabyte ) per second. It’s simple FIFO-like design makes it easy to interface
to any CPU ( MCU ) either by mapping the device into the Memory / IO map of the CPU, using DMA or controlling
the device via IO ports.
To send data from the peripheral to the host P.C. simply write the byte wide data into the device when the
transmitter empty status bit is not active. If the ( 384 byte ) transmit buffer fills up, the device de-asserts
transmit empty in order to stop further data being written to the device until some of the FIFO data has been
transferred over USB.
When the host P.C. sends data to the peripheral over USB, the device will assert the receiver full status
bit to let the peripheral know that data is available. The peripheral then reads the data until the receiver full
status bit goes inactive, indicating no more data is available to read.
By using FTDI’s virtual COM Port drivers, the peripheral looks like a standard COM Port to the application
software. Commands to set the baud rate are ignored – the device always transfers data at it’s fastest rate
regardless of the application’s baud rate setting.
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
Figure 1 – FT8U245AM Block Diagram ( Simplified )
VCC
3.3 Volt
3V3OUT FIFO Receive
LDO
Buffer
Regulator
128 Bytes
D0
D1
D2
D3
D4
USBDP D5
Serial Interface D6
USB USB FIFO
Engine D7
Transceiver Protocol Engine Controller
USBDM ( SIE )
RD#
WR
RXF#
TXE#
FIFO Transmit
Buffer EEREQ#
USB DPLL
384 Bytes
EEGNT#
T E
XTOUT EECS
48MHz GND EEPROM
EESK
6MHZ x8 Clock Interface
RESET#
E
Oscillator Multiplier EEDATA
XTIN 12MHz TEST
L
RCCLK
S O
B
Figure 2 – FT8U245AM I.C. Pinout
O
RCCLK
XTOUT
AGND
AVCC
EECS
XTIN
VCC
D0
32 25
EESK 1 24 D1
D2
FTDI
EEDATA
VCC D3
RESET# D4
TEST
3V3OUT
FT245AM D5
D6
USBDP
USBDM 8
XXYY 17
D7
GND
9 16
EEREQ#
VCC
EEGNT#
RD#
GND
RXF#
TXE#
WR
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
FT8U245AM - FUNCTIONAL BLOCK DESCRIPTION
• USB Transceiver
The USB Transceiver Cell provides the USB 1.1 full-speed physical interface to the USB cable. The
output drivers provide 3.3 volt level slew rate control signalling, whilst a differential receiver and two single
ended receivers provide USB data in, SEO and USB Reset condition detection.
• USB DPLL
The USB DPLL cell locks on to the incoming NRZI USB data and provides separate recovered clock and
E
data signals to the SIE block.
• 6MHz Oscillator
E T
L
The 6MHz Oscillator cell generates a 6MHz reference clock input to the X8 Clock multiplier from an
O
external 6MHz crystal or ceramic resonator.
S
• X8 Clock Multiplier
B
The X8 Clock Multiplier takes the 6MHz input from the Oscillator cell and generates a 12MHz reference
O
clock for the SIE, USB Protocol Engine and UART FIFO controller blocks. It also generates a 48MHz
reference clock for the USB DPPL and the Baud Rate Generator blocks.
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
• FIFO Transmit Buffer ( 384 bytes )
Data written into the FIFO using WR# is stored in the FIFO Transmit Buffer. The Host removes Data
from the FIFO Transmit Data by sending a USB request for data from the device data in endpoint.
• FIFO Controller
The FIFO Controller handles the transfer of data between the external FIFO interface pins and the FIFO
Transmit and Receive buffers.
• EEPROM Interface
The FT8U245AM uses an external 93C46 EEPROM to customise the USB VID, PID, Serial Number and
Strings of the FT8U245AM for OEM applications. The FT8U245 Virtual Com Port Drivers rely on a unique
device serial number for to bind a unique virtual COM port to each individual device.
T E
L E
S O
OB
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
Table 1 - FT8U245AM - PINOUT DESCRIPTION
E
25 D0 I/O Bi-directional Data Bus Bit # 0
T
24 D1 I/O Bi-directional Data Bus Bit # 1
E
23 D2 I/O Bi-directional Data Bus Bit # 2
L
22 D3 I/O Bi-directional Data Bus Bit # 3
O
21 D4 I/O Bi-directional Data Bus Bit # 4
S
20 D5 I/O Bi-directional Data Bus Bit # 5
19 D6 I/O Bi-directional Data Bus Bit # 6
B
18 D7 I/O Bi-directional Data Bus Bit # 7
O
16 RD# IN Enables Current FIFO Data Byte on D0..D7.when low.
Fetches the next FIFO Data Byte ( if available ) from the
Receive FIFO Buffer when RD# goes from low to high.
15 WR IN Writes the Data Byte on the D0..D7 into the Transmit FIFO
Buffer when WR goes from high to low.
14 TXE# OUT When high, do not write data into the FIFO. When low, data can
be written into the FIFO by strobing WR high then low.
12 RXF# OUT When high, do not read data from the FIFO. When low, there is
data available in the FIFO which can be read by strobing RD#
low then high again.
11 EEREQ# IN Requests the EEPROM contents to be accessed via the Data
Bus.
10 EEGNT# OUT When low, allows the EEPROM contents to be accessed via the
Data Bus.
3,13,26 VCC PWR Device - +4.4 volt to +5.25 volt Power Supply Pins
9.17 GND PWR Device – Ground Supply Pins
30 AVCC PWR Device - Analog Power Supply for the internal x8 clock multiplier
29 AGND PWR Device - Analog Ground Supply for the internal x8 clock
multiplier
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
FT8U245AM TIMING DIAGRAM – FIFO READ CYCLE
T6
T5
RXF#
T1 T2
RD#
T3 T4
E
Time Description Min Max Unit
T
T1 RD Active Pulse Width 50 ns
E
T2 RD to RD Pre-Charge Time 50 ns
L
T3 RD Active to Valid Data 30 ns
T4 Valid Data Hold Time from RD inactive 10 ns
O
T5 RD Inactive to RXF# 5 25 ns
S
T6 RXF inactive after RD cycle 80 ns
OB
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
FT8U245AM TIMING DIAGRAM – FIFO WRITE CYCLE
T12
T11
TXE#
T7 T8
WR
T10
T9
Time Description
E
T7 WR Active Pulse Width 50 ns
L
T8 WR to WR Pre-Charge Time 50 ns
O
T9 Data Setup Time before WR inactive 20 ns
S
T10 Data Hold Time from WR inactive 10 ns
T11 WR Inactive to TXE# 5 25 ns
B
T12 TXE inactive after RD cycle 80 ns
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
Figure 3. FT8U245AM - PACKAGE DESCRIPTION – QFP 7mm x 7mm
9
7
7 9
32
T E
E
0.8
L
Pin # 1
S O
B
1 0.37 +/- 0.07
O
12o +/- 1o
1.4 +/- 0.05
1.60 MAX
0.05 Min
0.15 Max
0.2 Min All dimensions in
0.6 +/- 0.15 millimetres
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
Absolute Maximum Ratings
o o
Storage Temperature ……………………………………………………. -65 C to + 150 C
o o
Ambient Temperature ( Power Applied )……………………………….. 0 C to + 70 C
VCC Supply Voltage ……………………………………………….…….. -0.5v to +6.00v
DC Input Voltage - Inputs ……………………………………………….. -0.5v to VCC + 0.5v
DC Input Voltage - High Impedance Bidirectionals …………………… -0.5v to VCC + 0.5v
DC Output Current – Outputs …………………………………………… 24mA
DC Output Current – Low Impedance Bidirectionals …………………. 24mA
Power Dissipation ………………………………………………………… 500mW
E
VCC Operating Supply Voltage 4.4 5.25 v
T
Icc1 Operating Supply Current 50 mA Normal Operation
E
Icc2 Operating Supply Current 250 uA USB Suspend
L
Ioh1 Digital IO Pins Source Current 4 mA Voh = VCC – 0.5v
O
Iol1 Digital IO Pins Sink Current 4 mA Vol = + 0.5v
Voh1 Input Voltage Threshold ( Low ) 0.6 v
S
Vol1 Input Voltage Threshold ( High ) 2.7 v
B
VDif USB Differential Input Sensitivity 0.2 v
O
VCom USB Differential Common Mode 0.8 2.5 v
URxt USB Single Ended Rx Threshold 0.8 2.0 v
UVh USB IO Pins Static Output ( Low ) 0.3v Rl = 1.5k to 3.6v
UVl USB IO Pins Static Output ( High ) 2.8 Rl = 15k to GND
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
Disclaimer
© Future Technology Devices International Limited – 1999, 2000
Neither the whole nor any part of the information contained in, or the product described in this manual, may
be adapted or reproduced in any material or electronic form without the prior written consent of the copyright
holder.
This product and its documentation are supplied on an as is basis and no warranty as to their suitability for
any particular purpose is either made or implied.
Future Technology Devices International Ltd. will not accept any claim for damages howsoever arising as a
result of use or failure of this product. Your statutory rights are not affected.
This product or any variant of it is not intended for use in any medical appliance, device or system in which
E
the failure of the product might reasonably be expected to result in personal injury.
E T
This document provides preliminary information that may be subject to change without notice.
Contact Information
O L
B S
Future Technology Devices Intl. Limited Telephone : +44 ( 0 ) 141 353 2565
St. George’s Studios Fax : +44 ( 0 ) 141 353 2656
O
93/97 St. George’s Road Email : [email protected]
Glasgow G3 6JA, UK Internet : http://www.ftdi.co.uk
Please visit our internet site for the latest contact details of our Agents and Sales Representatives world-wide.
Future Technology Devices Intl. FT8U245AM Preliminary Information Rev 0.9 – Subject to Change
Appendix A
T E
L E
S O
OB
USB Device Descriptors
{* device descriptor *}
LABEL : Device_Des;
LABEL : Device_Des_Vendor;
LABEL : Device_Des_Vendor_End;
E
{* end of device descriptor *}
T
LABEL : Device_Des_End;
LABEL : Config_Des;
E
{* configuration descriptor *}
L
0022 09 Val : $09;{length of this descriptor in bytes}
0023 02 Val : $02;{Configuration descriptor}
0024 20 00 Val : Config_Len,$00;{length of data returned for all things}
O
0026 01 Val : $01;{number of interfaces supported by this configuration}
0027 01 Val : $01;{configuration value}
S
0028 00 Val : $00;{index of string descriptor describing this configuration}
EC 0029 80 Val : 10000000b;{configured as bus powered and not remote wakeup}
E 002A 2D Val : 45;{maximum power in 2 mA ie 90mA for now}
B
{* end of configuration descriptor *}
O
LABEL : Interface_Des;
{* interface descriptor *}
LABEL : Interface_Des_End;
LABEL : Endpoint_Des;
LABEL : Endpoint3_Des_End;
LABEL : Endpoint_Des_End;
LABEL : Config_Des_End;
LABEL : Str0_Des;
LABEL : Str1_Des;
E
LABEL : Str1_Des_End;
T
LABEL : Str2_Des;
E
E 0051 03 Val : $03; {type string}
E 0052 55 00 Val : 'U',$00;
L
E 0054 53 00 Val : 'S',$00;
E 0056 42 00 Val : 'B',$00;
O
E 0058 20 00 Val : ' ',$00;
E 005A 3C 00 Val : '<',$00;
E 005C 2D 00 Val : '-',$00;
S
E 005E 3E 00 Val : '>',$00;
E 0060 20 00 Val : ' ',$00;
B
E 0062 53 00 Val : 'S',$00;
E 0064 65 00 Val : 'e',$00;
E 0066 72 00 Val : 'r',$00;
O
E 0068 69 00 Val : 'i',$00;
E 006A 61 00 Val : 'a',$00;
E 006C 6C 00 Val : 'l',$00;
LABEL : Str2_Des_End;
LABEL : Str3_Des;
T E
EEPROM Data Structure
L E
S O
OB
E2Rom Data example
LABEL : ManStringDes;
E
001E 73 00 Val : 's',$00;
LABEL : ManStringDes_End;
T
LABEL : ProdStringDes;
E
0020 34 Val : ProdStringDes_Len; {length of string descriptor}
0021 03 Val : $03; {type string}
L
0022 57 00 Val : 'W',$00;
0024 6F 00 Val : 'o',$00;
0026 6E 00 Val : 'n',$00;
O
0028 64 00 Val : 'd',$00;
002A 65 00 Val : 'e',$00;
S
002C 72 00 Val : 'r',$00;
002E 66 00 Val : 'f',$00;
0030 75 00 Val : 'u',$00;
B
0032 6C 00 Val : 'l',$00;
0034 6C 00 Val : 'l',$00;
0036 20 00 Val : ' ',$00;
O
0038 55 00 Val : 'U',$00;
003A 53 00 Val : 'S',$00;
003C 42 00 Val : 'B',$00;
003E 20 00 Val : ' ',$00;
0040 3C 00 Val : '<',$00;
0042 2D 00 Val : '-',$00;
0044 3E 00 Val : '>',$00;
0046 20 00 Val : ' ',$00;
0048 53 00 Val : 'S',$00;
004A 65 00 Val : 'e',$00;
004C 72 00 Val : 'r',$00;
004E 69 00 Val : 'i',$00;
0050 61 00 Val : 'a',$00;
0052 6C 00 Val : 'l',$00;
LABEL : ProdStringDes_End;
LABEL : SerStringDes;