STD 15257
STD 15257
PART 1 - GENERAL
1.01 DESCRIPTION
This section includes materials, fabrication, installation, and testing of fusion-bonded epoxy
lined and coated steel pipe used inside and outside of pressure reducing stations and
meter stations. Size range is 4- to 12-inch nominal pipe size.
A. Standard Drawings.
1.03 SUBMITTALS
B. Submit piping layout drawings showing location and dimensions of all pipe and fittings.
Include laying lengths of valves and other equipment determining piping dimensions. Label
or number each fitting or piece of pipe and provide the following information for each item:
OMWD 06-2008
STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED STD SPEC 15257 - 1
5. Call out all weld sizes and dimensions of grooved ends, flanges, fittings, and joint
harnesses.
C. Submit coating application test records for measuring coating thickness and holiday
detection for each pipe section and fitting. Describe repair procedures used.
B. Where new pipelines are to be connected to existing waterlines of the District, the
Contractor shall verify in the field the location, elevation, pipe material, pipe outside
diameter, and any other characteristics of the existing waterline before proceeding with the
pipe fabrication or installation. This field verification shall be performed in the presence of
the District’s Representative. Adjust and align the new piping as necessary to meet the field
conditions and provide all required material, labor, and equipment to make the connection.
PART 2 - MATERIALS
Pipe shall be black carbon steel conforming to ASTM A 53, Type E or S, Grade B; API 5L,
Grade B; or ASTM A 135, Grade B. Pipes shall be standard weight per ASME B36.10.
A. Steel fittings are defined as a special piece of pipe other than a normal straight section.
Elbows, crosses, tees, and reducers are fittings.
B. Fittings shall be butt-welded conforming to ASME B16.9. Material shall be wrought steel
conforming to ASTM A 234, Grade WPB. Wall thickness shall be the same as the pipe.
Lining and coating shall be a 100% solids, thermosetting, fusion-bonded, dry powder epoxy
resin. Provide Scotchkote 134 or 206N, Lilly Powder Coatings "Pipeclad 1500 Red", or
District approved equal. Epoxy lining and coating shall meet or exceed the following
requirements:
OMWD 06-2008
STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED STD SPEC 15257 - 2
Penetration 0 mil (ASTM G 17)
Use a two-component, 80% solids, liquid epoxy resin, such as Scotchkote 306 or District
approved equal.
2.05 FLANGES
A. Provide flanges that match the flange of the connecting valve or other equipment.
B. Provide welding neck flanges for attachment to wrought steel fittings. Provide welding neck
or slip on flanges for attachment to pipe. Slip on flanges shall be double welded. Flange
material shall conform to ASTM A 105, A 181, or A 182. Flanges shall be flat faced.
C. Class 150 flanges shall comply with AWWA C207, Class E or ASME B16.5, Class 150.
D. Class 300 flanges shall comply with AWWA C207, Class F or ASME B16.5, Class 300.
2.08 OUTLETS
A. For threaded outlets 3 inches and smaller, use a thredolet type per AWWA Manual M11
(Current Edition), Chapter 13. Outlets shall be 3000 pound WOG forged steel per ASTM A
105 or ASTM A 216, Grade WCB. Threads shall comply with ASME B1.20.1, NPT. Outlets
shall be Bonney Forge Co. "Thredolet," Allied Piping Products Co. "Branchlet," or District
approved equal. Do not use pipe couplings for outlets.
B. For flanged outlets 4 inches and larger, use a tee with a welding neck flange.
A. Mechanical clamp-type couplings for grooved end pipe shall be ductile iron, ASTM A 536,
Grade 65-45-12. Bolts shall conform to ASTM A 183, 110,000 psi tensile strength. Gaskets
shall be EPDM (ethylene propylene diene monomer) conforming to ASTM D 2000.
Couplings shall conform to AWWA C606 for flexible, square cut grooved joints in IPS steel
pipe. Couplings shall be Victaulic Style 77, or District approved equal.
OMWD 06-2008
STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED STD SPEC 15257 - 3
B. Line and coat couplings the same as the pipe. Color shall match the color of the pipe fusion
epoxy coating.
B. Joints between pipe, fittings, and welding neck flanges shall be full penetration butt welds.
Joints between pipe and slip on flanges shall be fillet welds to the interior and exterior. Do
not field weld to join components.
C. Provide grooved end pipe where mechanical clamp-type couplings are to be used. Grooved
end joint shall be flexible, square cut per AWWA C606, Table 2. Apply 10 mils maximum of
fusion epoxy coating to the grooved end pipe surface.
D. Provide plain end pipe where flexible pipe couplings are to be used. Couplings and
harnesses shall conform to Standard Specification Section 15122. Line and coat couplings
and harnesses the same as the pipe. Color shall match the color of the pipe fusion epoxy
coating.
PART 3 - EXECUTION
A. Beveled ends for butt welding shall conform to ASME B16.25. Remove slag by chipping or
grinding. Surfaces shall be clean of paint, oil, rust, scale, slag, and other material
detrimental to welding. When welding the reverse side, chip out slag before welding.
B. Fabrication shall comply with ASME B31.3, Chapter V. Welding procedure and
performance qualifications shall be in accordance with Section IX, Articles II and III,
respectively, of the ASME Boiler and Pressure Vessel Code.
C. Apply full penetration weld to exterior joint of butt welded pipe, fittings, and welding neck
flanges. Apply fillet welds to the interior and exterior circumference of the pipe and slip on
flanges. Minimum size of fillet weld shall be equal to the steel cylinder thickness. Complete
each pass around the entire circumference of the pipe before commencing the next pass.
Use electrodes recommended by the pipe fabricator. Do not deposit more than 1/8-inch of
throat thickness per pass. The minimum number of passes or beads in the completed weld
shall be as follows:
OMWD 06-2008
STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED STD SPEC 15257 - 4
0.2500 and Less 2
Greater than 0.2500 3
D. Use the shielded metal arc welding (SMAW) process for welding.
E. Welding preparation shall comply with ASME B31.3, paragraph 328.4. Limitations on
imperfections in welds shall conform to the requirements in ASME B31.3, Table 341.3.2,
and paragraph 341.4 for visual examination.
G. Clean each layer of deposited weld metal prior to depositing the next layer of weld metal,
including the final pass, by a power-driven wire brush.
I. After shop fabrication and prior to shop applied epoxy, test each welded joint by the liquid
penetrant method. Conform to the requirements specified in ASTM E 165. The materials
used shall be either water washable or nonflammable. Products: "Spotcheck" by the
Magnaflux Corporation or "Met-L-Check Flaw-Findr" by the Met-L-Check Company. Chip
out all defects, reweld, and retest the section affected until it shows no leaks or other
defects.
A. Apply lining and coating per AWWA C213 except as modified herein.
B. Grind 0.020-inch (minimum) off the weld caps on the pipe weld seams before beginning the
surface preparation and heating of the pipe.
C. Grind surface irregularities, welds, and weld spatter smooth before applying the epoxy. The
allowable grind area shall not exceed 0.25 square foot per location, and the maximum total
grind area shall not exceed 1 square foot per pipe section. Do not use any pipe section in
which these requirements cannot be met.
D. Grind outside sharp corners, such as the outside edges of flanges and harness plates, to a
minimum radius of 1/4-inch.
E. Uniformly preheat the pipe prior to blast cleaning to remove moisture from the surface. The
preheat shall be sufficient to ensure that the pipe temperature is at least 5°F above the dew
point temperature during blast cleaning and inspection.
F. Sandblast surfaces per SSPC SP-5. Protect beveled pipe ends from the abrasive blast
cleaning.
G. Apply a phosphoric acid wash to the pipe after sandblasting. The average temperature of
the pipe, measured in three different locations, shall be 80°F to 130°F during the acid wash
procedure. The acid wash shall be a 5% by weight phosphoric acid solution. The duration
in which the acid is in contact with the pipe surface shall be determined by using the
average pipe temperature as tabulated below:
OMWD 06-2008
STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED STD SPEC 15257 - 5
Pipe Temperature Contact Time
(°F) (seconds)
80 52
85 45
90 36
95 33
100 28
105 24
110 21
130 10
After the acid wash has been completed, remove the acid from the pipe with demineralized
water having a maximum conductivity of 5 micromhos/cm at a minimum nozzle pressure of
2,500 psi.
H. Apply epoxy lining and coating by either the electrostatic spray or fluidized bed process.
Minimum thickness of lining and coating shall be 12 mils each, except for grooved end pipe
surfaces. Heat and cure per the epoxy manufacturer's recommendations. The heat source
shall not leave a residue or contaminant on the metal surface. Do not allow oxidation of
surfaces to occur prior to lining and coating. Do not permit surfaces to flash rust before
lining and coating.
The cured lining and coating shall be smooth and glossy, with no graininess or roughness.
The lining and coating shall have no blisters, cracks, bubbles, underfilm voids, mechanical
damage, discontinuities, or holidays.
A. Test lining and coating with a low-voltage wet sponge holiday detector in accordance with
AWWA C213, Section 5.3.3. If the number of holidays or pinholes is fewer than one per 10
square feet of coating surface, repair the holidays and pinholes by applying the coating
manufacturer's recommended patching compound to each holiday or pinhole and retest. If
the number of holidays or pinholes exceeds one per 10 square feet, remove the entire pipe
lining and coating and recoat the entire piping and retest.
B. Check for coating defects on the weld seam centerlines. There shall be no porous blisters,
craters, or pimples lying along the peak of the weld crown.
C. Measure the lining and coating thickness at three locations on each pipe section using a
coating thickness gauge calibrated at least once per eight-hour shift. Record each
measured thickness value. Where individual measured thickness values are less than the
specified minimum thickness, measure the coating thickness at 6-inch intervals along the
pipe length. The average of these measurements shall exceed the specified minimum
thickness value, and no individual thickness value shall be more than 2 mils below or 3 mils
above the specified minimum value. If a section of pipe does not meet these criteria,
remove the entire lining and coating and recoat the entire pipe section or fitting.
OMWD 06-2008
STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED STD SPEC 15257 - 6
D. The District's Representative will conduct in the field an independent inspection of the lining
and coating for compliance with the above criteria. Coated items failing his inspection will
be cause for rejection.
Lift pipe with wide belt slings. Do not use cable slings or chains. Support the pipe on
padded wooden blocks. Do not roll or drop the pipe on the ground or allow the pipe to fall
from the delivery trucks. Protect the lining and coating of the pipe from damage or
scratches. Cover pipe with plastic sheets and secure until ready for installation.
See Standard Specification Section 15251 for installation requirements of buried steel pipe.
Install the pipe with polyethylene encasement and other appurtenant items for the
installation. Inspect the lining and coating, and repair damaged areas in the field as
described herein.
A. Install pipe in vaults without springing, forcing, or stressing the pipe or any adjacent
connecting valves or equipment. Provide temporary supports and place the assembled
piping at the correct grade and position in the vault.
Install insulating flange kits with coatings per Standard Specification Section 13110.
B. Clean oil, grease, and dirt from the grooved ends of pipe. Repair any damage or holidays in
the shop applied coating before installing couplings. Apply the coupling manufacturer's
gasket lubricant to the gasket exterior including lips, pipe ends, and housing interiors.
C. Lubricate threads of bolts and nuts with oil or graphite prior to installation. Uniformly tighten
bolts and nuts alternately and evenly until coupling segments are seated. Apply torque to
nuts with a calibrated torque wrench as recommended by the coupling manufacturer.
Install flexible pipe couplings and joint harnesses where shown per Standard Specification
Section 15122.
OMWD 06-2008
STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED STD SPEC 15257 - 7
3.12 FIELD REPAIRS TO LINING AND COATING
Patch scratches and damaged areas incurred while installing fusion-bonded epoxy pipe
with a two-component, 80% solids (minimum), liquid epoxy resin. Wire brush or sandblast
the damaged areas per SSPC SP-10. Lightly abrade or sandblast the pipe lining and
coating on the sides of the damaged area before applying the liquid epoxy coating. Apply
the liquid epoxy coating to damaged linings and coatings to areas smaller than 20 square
inches. Patched areas shall overlap the parent or base coating a minimum of 1/2-inch. If a
damaged area exceeds 20 square inches, remove the entire pipe lining and coating and
recoat the entire piping and retest. Apply the liquid epoxy coating to a minimum dry-film
thickness of 12 mils.
Coat exterior surfaces of fusion-bonded epoxy pipe in vaults per Standard Specification
Section 09900, System No. 10. Apply finish coat in field. Do not apply prime coat.
Coat exterior surfaces of mechanical clamp-type couplings, flexible pipe couplings, and
joint harnesses the same as the adjacent pipes.
See Standard Specification Section 15144 for pressure testing requirements. Test pipe at
the same time that the primary pipelines are tested.
3.15 DISINFECTION
END OF SECTION
OMWD 06-2008
STEEL PIPE, FUSION-BONDED EPOXY LINED AND COATED STD SPEC 15257 - 8