Professional Documents
Culture Documents
Osmo 23G
Osmo 23G
OPERATION AND
MAINTENANCE MANUAL
ii
U NOTICE
iii
This page intentionally left blank.
iv
TABLE OF CONTENTS
1.0 GENERAL INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 The Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3.1 Read This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3.2 Use Proper Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3.3 Device Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 Flow Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Machine Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.6 Machine Permeate Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.7 Machine Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.8 Specifications for 23G Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.8.1 RO Feedwater Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.8.2 Permeate (Product Water) Flow Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.8.3 Concentrate Flow Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.8.4 Primary Operating Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.8.5 Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.8.6 Reverse Osmosis Machine Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.9 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.10 Medical Membrane Element Specification for Water Purification . . . . . . . . . . . . . . . . . . 11
2.0 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1 Machine Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2 Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.1 Inlet Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.2 Valve for Clean-In-Place (CIP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.3 Concentrate Outlet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.4 Permeate Outlet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4 Machine Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
v
4.3 ECM-100 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.1 Selecting Parameters and Changing Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.2 Responding to an Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.3 ECM-100 Clean-in-Place (CIP) Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.4 ECM-100 Display Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.4.1 ECM Display Screen Hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.4.2 Detail of Date and Time Operation (Menu 01) . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.4.3 Detail of Alarm Limits Operation Menu (Menu 02). . . . . . . . . . . . . . . . . . . . . . 33
4.4.4 Detail of Timer Presets Operation (Menu 03) . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.4.5 Detail of Accumulated Hours Operation (Menu 04) . . . . . . . . . . . . . . . . . . . . ..35
4.4.6 Detail of Log Tables Operation (Menu 05). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.7 Detail of Calibration Operation (Menu 06) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.8 Detail of Print Current Values Operation (Menu 08) . . . . . . . . . . . . . . . . . . . . 37
4.4.9 Detail of Metric/US Select Operation (Menu 09). . . . . . . . . . . . . . . . . . . . . . . . 37
4.4.10 Detail of Perm High Conductivity Alarm Operation (Menu 10) . . . . . . . . . . . . 37
4.4.11 Detail of Factory Settings Operation (Menu 11) . . . . . . . . . . . . . . . . . . . . . . . . 38
4.4.12 Detail of Auto-On Tank Full Operation (Menu 12) . . . . . . . . . . . . . . . . . . . . . . 38
4.4.13 Detail of Comm Port Speed Operation (Menu 13) . . . . . . . . . . . . . . . . . . . . . . 38
vi
6.0 OPTIONAL FEATURES AND ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.1 Level Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.2 pH Controller/Sensor (ECM-100-pH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.3 Remote Alarm Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.3.1 Single Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.3.2 Six Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.4 Printer/Computer Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.4.1 Printer Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.4.2 Computer Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.4.3 Computer Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.4.4 Printer Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.4.5 Print Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.4.6 Print Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7.0 TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
7.1 Emergency Alarm Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7.1.1 Permeate Conductivity High or Rejection Low Alarms. . . . . . . . . . . . . . . . . . . 68
7.1.2 Rejection Low Alarm Due to Failed Feed Conductivity Probe . . . . . . . . . . . . . 68
7.1.3 Temperature High Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7.1.4 pH Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7.1.5 Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7.1.6 Permeate Flow (Stuck at Zero). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7.2 General ECM-100 Reference/Troubleshooting Guidelines. . . . . . . . . . . . . . . . . . . . . . . . 70
7.2.1 Resetting the ECM-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7.2.2 Check the Main Board Terminal Strip for Good Connections . . . . . . . . . . . . . 71
7.2.3 Check the Relay Board Terminal Strip for Good Connections . . . . . . . . . . . . . 71
7.2.4 Low Rejection Warning (Due to High Purity Feed Water) . . . . . . . . . . . . . . . . 71
7.2.5 Verifying the Temperature Circuitry of the Main Board. . . . . . . . . . . . . . . . . . . 72
7.2.6 Difficulty Calibrating Permeate Conductivity . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
7.2.7 Information to Obtain Before Contacting Your Equipment Supplier. . . . . . . . . 73
vii
9.0 RETURNED GOODS AUTHORIZATION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
10.0 WARRANTY/GUARANTEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
10.1 Machine Warranty/Guarantee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
10.2 Membrane Element Warranty/Guarantee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
viii
List of Figures
Figure Title
1.1 Membrane Element with Interconnectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Typical Flow Diagram for 23G Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4 Three-Phase Motor Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.5 ECM-100 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.6 23G Series ECM-100 Main Board Electrical Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.7 23G Series ECM-100 Relay Board Electrical Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.8 Brine Seal at the Exit End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.9 Membrane Element Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.10 Cross-Sectional View Membrane Element and Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.11 Flow Control Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
7.12 ECM-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
List of Tables
Table Title
1.1 23G Model Number Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Shipping Weights and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3 Single-Phase Electrical Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4 Three-Phase Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.5 ECM-100 Alarm Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.6 ECM1-00 Timer Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.7 Dry Chemical Cleaners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.8 Liquid Chemical Cleaners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.9 Liquid Chemical Sanitizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6.10 Example of ECM-100 History Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
ix
This page intentionally left blank.
x
1.0 GENERAL INFORMATION
1.1 General Description
CAUTION: When used as a medical device, Federal law restricts this device to sale by
or on the order of a physician, per 21 CFR 801.109 (b).
Your Osmonics 23G reverse osmosis machine is a durable piece of equipment which, with
proper care, will last for many years. These instructions give operating and maintenance
details vital to the sustained performance of the machine.
Reverse Osmosis (RO) is the separation of one component of a solution from another
component by means of pressure exerted on a semipermeable membrane. In other words,
reversing the natural passage of a liquid from a concentrate solution to a more dilute solution
by using external pressure. Removal of ionic, organic, and suspended/dissolved impurities
occurs during the RO process. Unlike a filter, which separates by “normal” filtration, the
membrane element separates using a process called cross-flow filtration. Feedwater solution
is separated into two streams, permeate and concentrate, and collected from both sides of
the membrane. A semipermeable RO membrane, under sufficient pressure, allows passage
of purified water while rejecting and concentrating dissolved and suspended solids.
Osmonics manufactures a spiral-wound membrane package, with turbulent flow design. This
membrane element module collects the purified water within a central tube (permeate
tube), as represented in Figure 1.1.
Interconnector
Mesh Spacer
ate Flow
Permeate Tube Concentr
ate Flow
Feed Flo
w Concentr
w
Perm eate Flo
w
O-Ring Feed Flo
Membrane Permeate Carrier
Membrane Backing Adhesive Bond
1
WARNING: Indicates statements that are used to identify conditions or
practices that could result in injury or loss of life.
FAILURE TO FOLLOW WARNINGS COULD RESULT IN
SERIOUS INJURY OR DEATH TO HEMODIALYSIS PATIENTS.
1.3.1 Read This Manual
Prior to operating or servicing this device, this manual must be read and
understood. Keep it and other associated information for future reference and for
new operators or qualified personal near the machine.
1.3.2 Use Proper Power Connections
Use proper wiring and connection methods as stated in this manual.
1.3.3 Device Labeling
Do not, under any circumstances, remove any Caution, Warning, or other
descriptive labels from the devices until the conditions warranting the label are
eliminated.
Operating definitions are provided to help you further understand your machine:
Permeate Rate [Product Water Rate (Qp)]
Permeate rate is the flow rate of purified water which has passed through the
membrane and out of the membrane element; expressed in gal/min (gpm) or gal/hr
(gph) [in metric, liter/min (Lpm) or cubic meters/hour (m3/h)]. Specified permeate
rates are normally at 77° F (25° C).
Concentrate Rate [Waste Water Rate (Qc)]
Concentrate rate is the flow rate of water containing rejected solids to drain in
gpm or gph (Lpm or m3/h).
Feed Rate (Qr)
Feed rate is the flow rate of incoming water in gpm or gph (Lpm or m3/h).
Feedwater rate equals permeate rate plus concentrate rate.
Recovery
Recovery is the percentage (%) of feedwater converted to permeate. For example,
75% recovery means that out of a given feed rate, 75% is produced as pure water
(permeate).
Concentration
Concentration equals the Total Dissolved Solids (TDS) of any stream (feedwater,
concentrate or permeate) of a solution expressed as milligrams per liter (mg/L) or
conductivity (microSiemens/cm).
Cf = Feed Concentration
Cp = Permeate Concentration
Cc = Concentrate Concentration
Cavg = Average Concentration in Machine
Salt (Ionic) Rejection
Salt (Ionic) Rejection is the percent of dissolved salt rejected by the membrane,
calculated from an average concentration over the membrane.
2
Salt (Ionic) Passage
Salt (Ionic) Passage is the percent of dissolved salts passed through the membrane.
Primary Pressure (Pp)
Primary Pressure (Pp) is the pressure between the pump discharge and the feed
port of the first membrane element housing.
Final Pressure (Pf)
Final Pressure (Pf) is the pressure between the concentrate outlet of the last
housing and the concentrate valve.
Pre-filter Pressure (Ppre)
Pre-filter Pressure (Ppre) is the water pressure entering the pre-filter.
Post-filter Pressure (Ppost)
Post-filter Pressure (Ppost) is the water pressure leaving the pre-filter.
Membrane Elements (Sepralators)
Membrane elements are the key to reverse osmosis. Interleaved layers of
semipermeable membrane, spacer and permeate carrier spiraled around a central
permeate tube make up the element. The spacer allows for movement of the
concentrate past the membrane, and the permeate carrier carries the pure water
out of the membrane element. Osmonics manufactures spiral-wound membrane
elements with a turbulent flow design. The membrane element collects the
permeate water within the central tube, called the permeate tube.
Recovery 75%
100 mg/L
C avg
3
1.4 Flow Description
The pretreated feedwater passes through a disposable 5 micron cartridge filter (pre-filter)
which removes suspended solids. Filtered water then flows to the inlet control valve. This
solenoid actuated valve is controlled by Enhanced Controller/Monitor (ECM-100) and opens
when the machine is turned on, allowing water to flow to the pump inlet. When the machine
is turned off, the valve closes, preventing laminar flow through the membrane element which
would lead to shortened membrane life.
The pump feeds water to the membrane element housings in a series and/or parallel
configuration, depending upon the design flow rates. The direction of water flow is indicated
by an arrow on each membrane element housing.
Permeate from each membrane element housing is collected at the permeate manifold
where a common check valve prevents backflow into the membrane elements. A pressure
sensor is provided to allow the ECM-100 to monitor excessive backpressure and initiate an
immediate alarm and machine shutdown should the setpoint be exceeded. Permeate is
directed through a turbine flow sensor and contacts a conductivity sensor before reaching
the outlet point of the machine.
The concentrate leaves the last membrane element housing and flows into the manifold
block. This concentrated water is then divided into recycle and concentrate streams. The
recycle portion mixes with the feedwater by returning to the inlet piping, allowing higher
machine recovery while still maintaining adequate crossflow through the membrane
elements. The concentrate valve on a 23G machine is used to increase the concentrate flow
rate for flushing. The normal concentrate flow rate is controlled by the concentrate orifice.
The concentrate valve or orifice has three functions: it controls the amount of concentrate
flowing to the drain; it controls the pressure within the machine; and it helps control system
recovery. A solenoid-controlled Autoflush valve is also provided in the concentrate line to
provide periodic intervals of increased drain flow rate controlled by the ECM-100. The
concentrate portion leaving the manifold block is directed through a turbine flow sensor
before reaching the outlet point of the machine.
4
ECM-100
ECM-100
S1
PI1
1.0 .75 .75 1.0
V V
1 2
PRE-FILTER
PE1 3
PRESSURE
SENSOR
INLET
1.00" NPTF T FILTER (2)
SCH 80 PVC TYPE: 10" OR 20" PPL
FILTER: GX05-10 OR GX05-20 ECM-100
INLET
VENT VALVE
P MR M
1.0 .75 .75 1.0
V V
CIP PORT
1" NPTF 1.25 .75" SS
V A
.75 1.0
V
.75 CENTRIFUGAL PUMP
FEED
B C CONDUCTIVITY AOV1 PRIMARY
pH PE3
AE1 1.00 PRESSURE
PE2 ECM-100
AE2 AE2
POST-FILTER
ECM-100 PRESSURE
ECM-100 ECM-100
S1 ECM-100
AI2
ECM-100 1 2
AAH1 AI1 PAH5
AA2H PI3
ACID ACID CHEMICAL CHEMICAL
AI2 PI2 3
DAY PUMP PUMP DAY
TANK OPTIONAL TANK
5
CIP PORT
V V 1" NPTF
S1
C
1 2
V V
V V
ADJ. ORF. (CONC.)
V V
FINAL
PE4
PRESSURE
C
SENSOR
V V
ECM-100
C
Table 1.1
23G Model Number Matrix
6
• Concentrate and percent rejection indication for permeate quality and membrane
performance monitoring.
• Temperature indication for feedwater temperature monitoring.
• Membrane element housings made of all 304 stainless steel.
• Autoflush - programmable periodic high velocity membrane flushing to maintain long
membrane life. Set at factory and adjustable in the field.
• Inlet low pressure alarm automatically shuts off the machine to prevent pump damage,
should inlet pressure fall to an inadequate level.
• Components in contact with the RO water (permeate) are made of either inert plastic
(nylon, poly-ethylene, Noryl*, polypropylene, PVC, EPDM, Nitrile) or stainless steel
materials.
• Memory for more than 400 sets of historical operating data (generated by approximately
2.5 full months of continuous operation).
• Comprehensive alarm package, with adjustable limits and common time-out, to ensure
safety and proper operation. Alarm is both visual and audible. Alarms include:
• high/low primary pressure (immediate shutdown on primary high pressure)
• low inlet post-filter pressure
• high permeate pressure (immediate shutdown)
• high/low pH
• high temperature
• high permeate conductivity
• low permeate conductivity
• low permeate flow
• low percent rejection
• high pre-filter pressure drop
• high membrane pressure drop
NOTE: All alarms except high primary pressure, high permeate pressure, and high
temperature are ignored in Clean in Place (CIP) mode.
7
1.8 Specifications for 23G Machines
1.8.1 RO Feedwater Specifications
The rated flow for all machines in this section is based upon the following
feedwater specifications. Limits should not be exceeded without consulting the
factory.
1. Continuous operation over 85° F (30° C) may cause permanent decline in the membrane
element performance. Actual permeate flow rates typically increase/decrease by 1.4% for
each 1° F change in temperature. For other temperatures, use “Temperature Factor Chart”
(Technote 113) to determine permeate rate. Contact authorized equipment supplier if
feedwater is outside these parameters.
2. The Langelier Saturation Index (LSI) of the concentrate must be negative to minimize
the possibility of calcium scale formation on the membrane surface. Refer to ASTM
Standard D3739.
3. Chlorine should be removed prior to the PA membrane in order to prolong the
functional life of the membrane element. Microbiological growth will not affect the
membrane itself, but may cause fouling and significant permeate flow rate decline. See
Membrane Specification Sheet for additional information.
4. Maintenance of feedwater Silt Density Index (SDI) as noted would minimize membrane
fouling and extend cleaning intervals. Treatment of feed waters with higher SDI values is
possible with more frequent cleaning and/or filter changes. Refer to ASTM Standard
D4189.
5. Components such as silica, barium, manganese, strontium, etc., must be below
saturation in the concentrate. Contact your equipment supplier for clarification if
unsure.
8
1.8.2 Permeate (Product Water) Flow Rate
As stated on the serial number label (assumes no permeate backpressure,
1000 mg/L TDS maximum feed concentration, and rated temperature).
To estimate the permeate output with backpressure, use the formula below:
(Permeate Flow on Label) x (Operating Pressure) - (Permeate Backpressure)
(Operating Pressure)
Maximum Permeate Backpressure: 60 psi (4.1 bar)
Permeate Outlet: 1-inch female NPT
*The molecular weight cutoff is based on the pore size of the membranes and the
nature of the organic molecule (size/shape).
9
Table 1.2 Approximate Shipping Weights and Dimensions
Model Number Shipping Dimensions Shipping Weight
23G 2 Element 65” D x 34” W x 78” H 655 lbs.
(165 cm D x 86 cm W x 200 cm H) (298 kg)
23G 3 Element 65” D x 34” W x 78” H 685 lbs.
(165 cm D x 86 cm W x 200 cm H) (311 kg)
23G 4 Element 65” D x 34” W x 78” H 725 lbs.
(165 cm D x 86 cm W x 200 cm H) (330 kg)
23G 5 Element 65” D x 34” W x 78” H 815 lbs.
(165 cm D x 86 cm W x 200 cm H) (370 kg)
23G 6 Element 81” D x 34” W x 78” H 845 lbs.
(205 cm D x 86 cm W x 200 cm H) (384 kg)
23G 7 Element 81” D x 34” W x 78” H 925 lbs.
(205 cm D x 86 cm W x 200 cm H) (420 kg)
23G 8 Element 81” D x 34” W x 78” H 1025 lbs.
(205 cm D x 86 cm W x 200 cm H) (466 kg)
23G 9 Element 81” D x 34” W x 78” H 1060 lbs.
(205 cm D x 64 cm W x 200 cm H) (480 kg)
23G 10 Element 81” D x 34” W x 78” H 1100 lbs.
(205 cm D x 64 cm W x 200 cm H) (500 kg)
23G 11 Element 90” D x 34” W x 88” H 1200 lbs.
(228 cm D x 64 cm W x 224 cm H) (545 kg)
10
1.10 Medical Membrane Element Specification
NaCl rejection: 99.0% Average (98.0% minimum)
Based on a 2,000 mg/L NaCl solution at 225 psig (1,551 kPa) operating pressure, 77°F (25°C), pH 7.5, 15%
recovery, after 24 hours. Individual element flow may vary 15%.
Design Parameters
Maximum pressure: 300 psig (2070 kPa)
Typical cleaning: <200 psig (1450 kPa)
Maximum temperature
Operating: 95 °F (35 °C)
Cleaning: 100 °F (37 °C)
Operating pH: 5.0- 10.0
Cleaning pH: 2.0 - 11.5
Feed NTU: <1
Feed SDI: <3
Chlorine tolerance: 1,000 ppm-hours Dechlorination recommended
Maximum Delta P: 10 psig (69 kPa) per element
11
2.0 INSTALLATION
2.1 Machine Location
At least 45 inches (114 cm) of space should be allowed above the membrane element
housings for easy removal and loading of membrane elements. Provide adequate work space
on sides and front for easy access.
NOTE: If necessary, housings may be detached from the frame for membrane
element removal due to space restrictions around the machine.
2.2 Plumbing
2.2.1 Inlet Plumbing
The feedwater source should be plumbed to the 1-inch FNPT inlet point on the
23G machine. If the inlet pressure is the excess of 60 psi (4.1 bar) or fluctuates by
more than 5 psi (0.3 bar), a pressure regulator should be installed ahead of the
connection. A low pressure sensor is installed on every 23G machine to protect
against low inlet pressure. The 23G should not be installed where the feedwater
dynamic inlet pressure is less than 20 psi (1.4 bar). If inlet pressure is less than
20 psi (1.4 bar), a booster pump must be installed ahead of the connection.
2.2.2 Valves for Clean-In-Place (CIP)
All 23G units have separate CIP connections. Valves should be installed on both the
main and inlet cleaning connections of the inlet stream. The permeate outlet and
concentrate outlet plumbing streams include factory installed manual shutoff valves.
CAUTION: Do not operate the machine with all concentrate and permeate
connections closed. Severe damage to the unit may result.
2.2.3 Concentrate Outlet Connection
Connect a 1.0-inch hose or pipe to the concentrate outlet and run to an open
drain. To avoid drainage to the machine during non-operation, the concentrate
outlet plumbing should be placed at a height which is at least equal to the height of
the machine. A siphon break may also be installed in the concentrate line for added
protection. The concentrate outlet hose or pipe can be any length, and the
diameter should match the outlet of the machine.
NOTE: Soft, flexible hose can be used, but must be installed in a manner which
prevents “kinks” or other restrictions that will increase back pressure
and reduce permeate flow rate to the drain.
2.2.4 Permeate Outlet Connection
Connect a 1.0-inch I.D. hose or pipe to the permeate outlet and run to the storage
tank (if applicable) or distribution loop (after distribution loop, points of use).
The pure water (permeate) should be transported to the point-of-use via non-
corroding inert-type tubing pipe or hose. Examples are: food grade flexible nylon
tubing, stainless steel tubing or PVC piping.
NOTE: Soft, flexible hose can be used, but must be installed in a manner which
prevents “kinks” or other restrictions that will increase back pressure
and reduce permeate flow rate to the drain.
NOTE: Do not use copper or galvanized tubing or piping to carry the
permeate. Only food grade materials and/or appropriate NSF materials
should be used.
12
2.3 Electrical
The ECM-100 controls and monitors the operation of the 23G, requiring a dedicated
115/230 VAC 60/50Hz, 15/10 A, 220 Vac, single-phase power source. All control output
devices (motor starter, solenoid valves, chemical pumps) draw power from this source
(through ECM-100 relay outputs) in addition to the ECM-100 itself. Refer to Figures 2.3 and
2.4 for connection details and ECM-100 inputs and outputs.
The ECM-100 monitors system operating parameters for alarm conditions to safeguard the
machine’s operation. User variation of the alarm limits and timer presets (set at the factory)
are possible by accessing the appropriate function from the system operations menu and
following the respective directions for making the changes.
The 23G pump is wired at the factory to an IEC overload protection magnetic motor starter
which is controlled by the ECM-100.
The procedure for connecting the electrical wiring for installation of the 23G follows:
1. Connect the ECM-100 power cord to a properly grounded 15 A, 115 VAC/60Hz or
10 A 220 VAC/50Hz, single-phase outlet. An appropriate termination should be installed
on the electrical cord for 220 VAC service. Surge protection for single-phase service is
recommended.
The ECM-100 relay output contacts are rated to handle a control ON relay-type circuit.
V2 relay boards, supplied in all 23G machines after November 1998, are designed to
handle a maximum load of 3.0 AMPS. The current requirements of all output device
(such as a remote alarm horn and light) must be within these limits.
The power cord of the ECM-100 should be connected to a power receptacle tied to a
“protective earth” ground to ensure a safe, common ground for the entire 23G unit,
including the three-phase motor. DO NOT remove the grounding wire from the pump
casing, the unit frame or a power supply grounding terminal.
WARNING: ALL SUPPLY CIRCUITS MUST BE DISCONNECTED BEFORE
OBTAINING ACCESS TO TERMINALS.
2. Separate power supplies are required for CIP and main pump.
3. Connect the magnetic motor starter to the proper voltage, phase and cycles to match
motor voltage and phase. Install the wires as indicated in Table 2.3 (single-phase) or
Figure 2.4 and Table 2.4 (three-phase). The overload trip point on the pump motor
starter may need to be adjusted slightly to match the actual voltage being provided.
Check the tag on the motor starter indicating the factory wiring. A separate, fused
disconnect for the motor wiring with the proper overload and short-circuit protection
for the Hp and amp draw of the motor is required. Bussmann Low-Peak Yellow LPS-RK-
SP fuses or equal are recommended for the disconnect.
NOTE: Field wiring must comply with all applicable national and local electrical codes.
2.4 Machine Lockout
In general, the machine should be operated in AUTO mode in which conditions are
confirmed electronically. The ECM-100 terminal strip has terminals available for linking other
treatment equipment, such as a softener, to the operation of the 23G machine or monitoring
the status of other equipment. The status of this equipment is indicated by Light-Emitting
Diode (LED) lights on the ECM-100. When operating in HAND mode, it is the operator’s
responsibility to ensure adequate feedwater supply and storage tank capacity.
Lockouts are ignored in HAND mode, such as full tank level, etc. CIP mode ignores
temperature and pH alarms.
13
The Pretreatment Lockout input can be used in AUTO mode to shut down the machine (all
outputs turned off) when there is an interruption of feedwater supply, such as when a
pretreatment filter is backwashing. The terminals for the Pretreatment Lockout on the
ECM-100’s main strip look for an “open” contact to shut down the machine and illuminate
the blue Pretreatment Lockout LED light.
14
Table 2.4 Three-Phase Electrical
Connections
15
3.0 PREPARATION AND START-UP
3.1 Pretreatment for Water Purification
Osmonics 23G machines will operate most efficiently on filtered water with a pH less than
negative concentration LSI (Langlier Saturation Index) and a Silt Density Index (SDI) of 3 or
below. If the machine is operated on water with higher pHs, other forms of pretreatment
may be necessary. A water analysis prior to start-up of the machine is required. To minimize
the chances of calcium carbonate, calcium sulfate, or other mineral precipitation on the
membrane, your equipment supplier will evaluate each application and water condition and
make specific recommendations to ensure continuity of membrane element warranty. Data
from the water analysis is processed with a computer program to determine if potential
problems may exist. If the machine is to be run at a different location than was originally
intended, a new water analysis is required for warranty consideration and should be sent to
your equipment supplier for review and recommendations for operation of the machine.
Before installing the machine, the feedwater must be filtered to 5 microns.
Machine feedwater must not contain the following chemicals or permanent loss of rejection
and/or permeate flow may result:
• free chlorine
• cleaning chemicals, biocides or sanitizing agents, such as formalin or peroxide
piracetic acid type products (until after membrane elements have been run to
drain for
8 hours)
• iodine compounds
• quaternary biocides
• cationic surfactants
• detergents containing non-ionic surfactants
• cleaners not approved by Osmonics
NOTE: A water softener should not be regenerated while the machine is running
unless safeguards such as a duplex softener are used to be sure the
machine is operated on softened water during regeneration. The machine
has a Pretreatment Lockout feature which can be used to shut the machine
off during regeneration.
3.2 Initial Start-Up
CAUTION: When the 23G RO machine is first installed or membrane elements are
changed, the RO unit must be rinsed to drain for a minimum of 8 hours
before exposure to cleaners or disinfectants as irreversible membrane
damage may occur.
1. Open the feed line valve. At least 20 psi (1.4 bar) dynamic feed line pressure is required.
2. Open the machine concentrate valve one or two turns. The machine concentrate valve
is located below the machine control panel on the left.
3. Open the permeate CIP connection to flush the machine. The CIP fitting requires a
1.0-inch MPT threaded fitting.
4. Close the permeate outlet valve.
5. Secure the end of the hose attached to the CIP fitting to a suitable drain.
Verify that the concentrate outlet valve is open.
Verify that the concentrate CIP valve is closed.
16
6. De-energize the high voltage power to the pump motor starter. Energize only the
115/230 volt control circuit by pressing the ON key on the ECM-100 controller and then
within 10 seconds, press the CIP key. The machine must be in HAND mode in order to
start the machine alarms with the CIP key. Using the CIP key in this way will bypass many
of the alarms. Let the water flow through the machine for at least five minutes under line
pressure to purge air from the system.
NOTE: The high pressure pump should not be operated during this time. If a buffer
system is being used, it should be set to regulate feedwater pH at 6.5 or
less. The control range for buffer pump operation is from 1.8 to 8.0 less
than the high pH alarm setting. The buffer pump will turn on at 0.8 units
less than the high pH setting and turn off at
1.8 units less than the high pH alarm setting.
NOTE: When the control circuit is de-energized, there should be no flow from the
concentrate outlet. The solenoid activated inlet valve should be closed
when de-energized. See Troubleshooting Guide (Section 7.0) if water
continues to flow after shutdown.
7. Switch off the 115/230 volt control circuit by pressing the OFF button on the ECM-100.
8. Re-energize the high voltage power to the pump motor starter. The pump should not
begin to operate.
9. Close the machine concentrate valve.
10. Start the machine by pressing the ON key on the ECM-100. Ensure that the pump
rotation is correct by observing the primary pressure. If the pressure is below 125 psi
(8.6 bar) then the motor may be rotating backwards.
CAUTION: High voltage electricity. Qualified personnel should perform this
procedure.
11. To correct rotation, turn the machine OFF. De-energize the high voltage power to the
pump motor starter and the control circuit. Verify with volt meter prior to adjusting
wires. Change any two of the three leads (for three-phase power) into the motor starter
and recheck rotation.
NOTE: For incorrect rotation on single-phase motor installation, contact your
equipment supplier.
CAUTION: Operation of the pump backwards may cause damage to the pump and
motor in addition to loss of pressure which affects permeate rate.
12. Re-energize all power.
13. Restart the machine by pressing the ON key on the ECM-100.
14. Verify that water is flowing from the permeate CIP outlet to the drain. The machine
concentrate valve is located below the machine control panel on the left.
NOTE: The 23G machine is designed to operate with the concentrate valve
closed, except during initial machine start-up/flushing, cleaning, and
sanitizing.
15. During typical start-up/flushing check the primary and final pressures which should be
below the typical maximum pressure of 280 psig. Field conditions may dictate slightly
higher alarm setpoints (refer to Section 1.8.4).
16. Continue to operate the machine in this manner for a period of 8 hours.
NOTE: When the 23G RO machine is first installed or membrane elements are
changed, the RO unit must be rinsed to drain for a minimum of eight (8)
hours before exposure to disinfectants or irreversible membrane damage
may occur.
17
17. Check permeate and concentrate flow rates and verify that they are within the
parameters listed on the machine label. Temperature correction factors should be
applied.
18. If any of the machine operating parameters are outside of the specifications listed on the
machine label contact your equipment supplier.
19. All operational data must be recorded on the Start-up Data Sheet (Section 10.0). The
Start-up Data Sheet must be submitted to your equipment supplier and to Osmonics
Medical Facility in Kent, WA for warranty consideration.
20. Shut down machine. Open permeate outlet valve. Close permeate CIP valve.
Machine is ready for normal operation, however do not put into service until all applicable
water tests have been completed.
In order to ensure that the RO is performing at or above AAMI standards, it is necessary to
perform an AAMI Water Quality Analysis Test. For new units, the RO must be operated
(rinsed to drain) for at least two hours before taking a sample, to ensure that the membranes
are free of preservatives or other contaminants which would invalidate the test.
NOTE: Follow the procedures recommended by your water quality testing laboratory.
3.3 Daily Start-Up and Operation Checklist
NOTE: This section may be copied for placement on the 23G machine.
CAUTION: HAND mode is for diagnostic test and CIP. It should not be operated while
unsupervised in this mode.
1. Verify that all feedwater valves and outlet valves in the permeate and concentrate plumbing
are open. At least 20 psi (1.4 bar) dynamic feed line pressure is required to prevent damage
to pump.
2. Make sure the ECM-100 is plugged into an appropriate circuit and the LCD screen is
active.
3. If the feedwater pH is being adjusted for membrane compatibility or scale inhibition,
verify that the chemical feed pump power switch is on.
If necessary, refer to Section 3.1 for further information on feedwater preparation.
4. Verify that the ECM-100 operating mode is AUTO. The machine operates independently
of external controls, such as tank float switch and pretreatment lockout signal, in the
HAND mode. In the AUTO mode, the machine operates according to signals from pre-
or post- treatment equipment, tank float switches, etc.
5. Press the ON key on the ECM-100. After a short delay, the high-pressure pump will
start. Alarms may occur during the first minute of operation as the RO machine
operation stabilizes. Alarms may be bypassed and muted until the alarms clear. If alarms
persist, address the specified alarm condition shown on the LCD screen according to
the Troubleshooting Guide (Section 7.0).
6. Verify that water is flowing from the permeate outlet. For dialysis applications verify the
water quality to ensure it meets the current applicable quality standards. Per the AAMI
standards, “It is the responsibility of the attending physician to ensure the water quality
is appropriate.”
7. The machine is now operating. If a pH buffer is being used with the pH control of the
ECM, readjust pump if necessary for a slowly dropping pH reading while the injection
pump is on. The control range for the buffer pump operation is from 1.8 to 0.8 less than
the high pH alarm setting.
8. Daily operating logs should be completed every 8 hours. A Daily Log Sheet (Section
14.0) is provided in the instruction manual for this purpose.
18
4.0 ECM-100 OPERATION
4.1 ECM-100 General Description of Operation
The ECM-100 is a state-of-the-art electronic controller/monitor designed for 23G machines.
The ECM-100 controls and monitors machine operation including operating performance.
Data is stored automatically by the ECM-100 at preset run-time intervals and can be
downloaded to a printer or PC port via a RS-232 communication port.
4.2 ECM-100 Displays and Controls
The ECM-100 displays and controls are as follows (Reference Figure 4.5):
4.2.1 System Status Lights - Left Column
Machine On Indicates that the machine is either running or is in standby
mode.
Alarm Indicates an alarm condition.
Tank Full Indicates that a signal from a tank level control has put the
machine in standby mode.
Pretreatment Lockout Indicates that a signal from pretreatment equipment has
put the machine in standby mode.
Permeate Divert Indicates that the permeate is being diverted to drain.
4.2.2 System Status Lights - Right Column
RO Pump On Indicates RO pump (main high-pressure pump) should be
running.
CIP Pump On Indicates CIP pump should be running.
Autoflush Indicates the Autoflush valve should be open.
Auto-On Active Indicates that the Auto-On feature is active; the machine
will start automatically and run a short time if left idle for
more than a preset time. (This inhibits bacteria growth
during periods of non-use).
Auxiliary Indicates that an auxiliary component is on (such as a tank
transfer pump).
4.2.3 Keypad - Control Section
LED Lights
HAND - Manual on/off, ignores tank level and pretreatment lockouts.
AUTO - Signal-controlled on/off (from pretreatment or level controls).
CIP - Works in HAND only, locks out most alarms (Section 4.5.3).
Keys
On and Off
HAND/AUTO toggle
Clean-in-Place
Alarm bypass
Mute button
19
4.2.4 Keypad - Menu Select Section
LED Lights
U.S. - Units of measurement
Metric - Units of measurement
Keys
ARROW (scroll) keys
ENTER key
ESCAPE (ESC) key
4.2.5 Liquid Crystal Display (LCD)
Displays date, time, 10 operating parameters, and alarm or menu messages.
Menu Abbreviations:
CVAL - Current value
SETPT - Calibration set point
Q - Flow rate
PERM - Permeate
CONC - Concentrate
20
Figure 4.5 ECM-100 Front Panel
21
4.2.6 ECM-100 Passcode
Your machine is equipped with an ECM-100 controller/monitor to perform the
machines electrical operations. Selected functions of the ECM-100 require entry of
a passcode. This passcode access allows three functions; it allows a user to make
adjustments to setpoints view, and download historical data. The passcode is
intended to provide access adjustment capability to authorized personnel.
The passcode for your ECM-100 is entered by pressing the function keys on the
ECM-100 keypad, in the following sequence:
1. HAND/AUTO
2. CIP
3. ALARM BYPASS
Contact your equipment supplier for assistance.
4.2.7 Factory Settings Storage
1. The “factory settings” is a copy of all menu data stored in a separate reserved
storage area.
2. This data can be updated by following the procedure described as “Store
Factory Settings.”
3. Osmonics factory personnel saved a copy of menu settings before the machine
was shipped.
4. At installation, after timers and calibrations have been tailored for your
particular application, and/or after recalibration of pH probe the settings need
to be copied to the factory settings area for permanent storage.
5. In the event that the settings have been corrupted the menu settings can be
recalled.
6. To store Factory settings:
a. Go to the Factory Settings Menu (menu 11).
b. Push ENTER switch. The screen will display two lines of factory settings.
c. Enter storage code in the following sequence:
HAND/AUTO
CIP
ON
ENTER
7. To recall factory settings:
a. Go to the Factory Settings Menu (menu 11).
b. Push ENTER switch. The screen will display two lines of factory settings.
c. Enter passcode (Section 4.2.6) to restore factory settings.
Contact your equipment supplier for assistance.
4.2.8 Display Menus
01 Date and Time
The Date and Time Menu should be used to change/update the respective display.
Press ENTER to select. Enter the passcode (Section 4.2.6) to allow for date and
time adjustment. Use the ARROW keys to raise and lower the value, then press
ENTER to store and advance to the next alarm. When all the limits have been
entered, the ECM-100 will automatically return to the default menu.
22
02 Alarm Limits
The Alarm Limits Menu should be used to change/modify the alarm duration(s) and
setpoint(s).
Press ENTER to select. Press ENTER to advance through the list. Enter the
passcode to adjust any of the settings. Use the ARROW keys to raise or lower the
alarm limit value, then press ENTER to store and advance to the next alarm
setting or ESC to exit and leave the value unchanged. When all of the timers have
been entered, the ECM-100 will automatically return to the default menu.
03 Timer Presets
The Timer Presets Menu should be used to change/modify timer durations.
Press ENTER to select. Press ENTER to advance through the list. Enter the
passcode to adjust any of the settings. Use the ARROW keys to raise or lower the
timer preset value, then press ENTER to store and advance to the next timer.
When all of the timers have been entered, the ECM-100 will automatically return
to the default menu.
04 Accumulated Hours
The Accumulated Hours Menu is used to display machine run time and non-
running time. Times are displayed in hours.
Press ENTER to view the accumulated hours for “RUN” time and “OFF” time.
05 Log Tables
The Log Tables Menu allows the user to display and download historical machine
operational data.
Press ENTER to view the data tables. Use the ARROW keys to advance through
the data tables. Enter the passcode to download the data tables to a printer or
computer starting with the table in view on LCD. Three pages (up to 400 lines) of
historical data will be downloaded. Used the DOWN ARROW key to advance to
and download older data tables, if desired, before exiting the log tables menu.
Repeating the download sequence twice will download the entire historical record
log (up to 10 weeks of data recorded: is adjustable to one reading per hour during
a 40 hour work week).
06 Calibration
The Calibration Menu should be used to change/modify calibration parameters for
sensors (flow, temperature, conductivity) and transducers (pressure).
Press ENTER to select and advance through the list. Enter the passcode to change
a calibration parameter value. Use the ARROW keys to raise or lower the
calibration value, then press ENTER to store and advance to the next parameter.
When all calibration numbers have been entered, the ECM-100 will automatically
return to the default menu.
NOTE: When performing the two-point pH calibration, the passcode must be
entered immediately prior to adjusting the calibration number for each
pH CAL LOW and pH CAL HIGH. The passcode must be entered even
if you have already entered the code to adjust a calibration number or
parameter earlier in the list (this is to prevent inadvertent loss of pH
calibration while viewing the calibration parameters). Be sure to store
the Factory Settings (Maintenance Menu 11) after calibrating the pH
probe.
23
07 Maintenance
The Maintenance Menu is used to gain access to all general operational conditions/
functions (menu options 08-13).
Press ENTER to select. Use the UP ARROW key to advance through the
maintenance functions. Press ENTER to select a function.
08 Print Current Values
The Print Current Values Menu is used to facilitate a download of current
operational data.
Press ENTER to print/send the data that is currently displayed on the ECM-100
screen to a printer or computer.
09 Metric/U.S. Select
The Metric/U.S. Select Menu option is used to specify the units of measure
displayed on the ECM-100.
Press ENTER, then use the ARROW keys to toggle between choice of units. Press
ENTER to select.
10 Perm Hi Cond Alarm
The Perm Hi cond Alarm Menu is used to specify/modify the machine’s response to
a high permeate conductivity condition.
Enter the passcode to select one of the three alarm responses. Use the ARROW
keys to toggle through the responses. Press ENTER to select.
11 Factory Settings
The Factory Settings Menu is used to store and recall menu settings.
Enter the passcode to recall default factory settings. See Section 4.4 for saving and
recalling factory settings.
12 Auto-On Tank Full
The Auto-On Tank Full Menu is used to control the machines response to a tank
full condition.
Press ENTER, then use the ARROW keys to toggle between shutdown (default)
and divert (used only if permeate divert option is installed). Press ENTER to select
or ESC to exit.
NOTE: If “Divert” is selected, the AUTO-ON function will come on even if
the tank is full, and Perm Divert will come on anytime the tank is full
(even in HAND mode).
NOTE: Appropriate plumbing must be installed to divert permeate and to
prevent overflowing the tank. The machine should be left “ON” and in
AUTO. After the tank fills up normally, the AUTO-ON will periodically
start-up and run for a short time to flush the machine. During this time
the permeate is in DIVERT mode.
13 Comm Port Speed
The Communication (Comm) Port Speed Menu is used to set the baud rate of the
RS-232 serial port.
24
NOTE: The computer or printer must be set to the same baud rate as the
ECM-100.
Press ENTER, then use the ARROW keys to scroll through the choices. Press
ENTER to select, or ESC to leave the settings unchanged.
Refer to the ECM-100 Menu Summary included with this instruction manual for
further information on ECM-100 operation.
4.3 ECM-100 Operation
The following is a description of how the ECM-100 is used to operate the 23G machine. The
passcode and storage code required to make adjustments to various settings and timers are
provided in Section 4.2.6 and Section 4.2.7.
1. Press ON to turn on the machine and OFF to turn it off. Press HAND/AUTO to toggle
between the two operating modes. AUTO is defined as an operation which is controlled
by tank level and pre-treatment lockout inputs. HAND is defined as an operation which
ignores those same inputs and most alarms. The unit should not be left unattended in
HAND mode.
2. On start-up, a predetermined sequence of events occur. The inlet valve opens and the
RO pump comes on (after a time delay). The permeate divert valve will close and the
permeate outlet valve will open after a preset duration. The RO pump start time delay
and permeate divert duration can be viewed and adjusted in the Timer Presets Menu
(03).
3. Press the Menu select ARROW keys to scroll through the various system operations, 01
through 07 (pressing ENTER will select desired menu). The Maintenance Menu (07)
allows access to additional operations numbered 08 through 13. After entering the
Maintenance Menu (07), press the UP ARROW key to toggle through the list of
maintenance operations (again, pressing ENTER will select desired menu). Press ESC
twice at any time to return to the default screen, which displays the time and date and
up to 10 operating parameters.
4.3.1 Selecting Parameters and Changing Settings
To select a parameter:
1. Scroll through the parameters using the ARROW keys until the desired parameter
is shown on the LCD screen.
2. Press the ENTER key.
3. Scroll through the settings using the ARROW keys, until the desired setting is
displayed on the LCD screen.
To change a setting:
1. Enter the passcode.
2. Raise or lower (toggle between) settings, using the ARROW keys.
3. Once the desired setting is shown on the LCD screen, press ENTER to store
and advance.
4. Press ESC to cancel or change and ECS again to return to the default screen.
4.3.2 Responding to an Alarm
When the machine alarm is indicated by the ECM-100 controller, a signal is
transmitted from the base unit to the ECM-100. An audible alarm will sound, the
large alarm light will turn on, and a small alarm light (corresponding to the
appropriate alarm condition) will identify the alarm. The mute button on the unit
will silence the alarm horn, but the horn will reactivate if a new alarm condition is
25
indicated. The alarm light will turn off and horn will silence automatically when the
alarm conditions clear.
Pressing the Alarm Bypass key will add one minute to the shutdown delay timer to
allow time for remedy (the alarm continues to sound, but the machine will not
shutdown until after the delay).
4.3.3 ECM-100 Clean-in-Place (CIP) Operation
For CIP operation from the ECM-100 follow these steps:
1. Confirm the machine is in HAND mode (check LED light), as CIP will not work
in AUTO mode.
2. Press the ON key to start the machine.
3. Within 10 seconds of pressing ON, press the CIP key; the CIP LED should
illuminate.
The same sequence of events will occur on start-up as occurs when just ON is
pressed, except the CIP pump will start as soon as the machines inlet valve opens
and the pH buffer pump will not turn on.
The following alarms are disabled and will not activate while in CIP mode:
• high/low pH
• permeate conductivity
• low inlet pressure
• low primary pressure
• low permeate flow
• high membrane pressure drop
• high filter pressure drop
• low machine rejection alarms
NOTE: CIP is intended to be a manual process with an operator present for the
duration of the cycle.
26
Table 4.5 ECM-100 Alarm Settings
Alarms Range Factory Preset
(Menu 02)
PERM COND HI 0 - 200 µS/cm (Note 1, 2) 30 µS/cm
TEMP HI 0 - 255oF (0-123oC) 105oF (41oC)
pH HI 0.0 - 14 pH units (Note 3) 7.0 pH units
pH LOW 0.0 - 14 pH units 3.5 pH units
POST FILTER PRESS LOW 0 - 99 psi [0 - 68 (bar x 10)] 12 psi [8 (bar x 10)]
PRIMARY PRESS HI 0 - 510 psi [0 - 352 (bar x 10)] 280 psi [193 (bar x 10)]
PRIMARY PRESS LOW 0 - 510 psi [0 - 352 (bar x 10)] 150 psi [103 (bar x 10)]
PERM PRESS HI 0 - 99 psi [0 - 68 (bar x 10)] 80 psi [55 (bar x 10)]
REJECTION LOW 0 - 99% 88%
FILTER PRESS DROP HI 0 - 99 psi [0 - 68 (bar x 10)] (Note 4)
MEMBRN PRESS DROP HI 0 - 510 psi [0 - 352 (bar x 10)] (Note 5)
PERM FLOW LOW 0.0 - 20.1 gpm (0.0 - 76.5 L) (Note 6)
1. Adjustments range for “Permeate Conductivity High” alarm is 0 - 50 µS/cm for Rev D3
software; 0 - 200 µS/cm for Rev EO or higher software.
2. Below 200 µS/cm, there are 2.5 units of specific conductance (µS/cm) per unit of TDS
(ppm or mg/L CaCO3).
3. If an acid injection pump is installed, the high pH alarm determines when the chemical
pump turns on. Once the pH rises to 0.8 units below the alarm setting, the pump turns
on. After the chemical pump lowers the pH to 1.8 units below the alarm setting, the
pump will be turned off.
4. Set alarm limit at 8 psi [6 (bar x 10)] greater than drop observed during data collection
for QA test form.
5. Set alarm limit at 1.5 x the drop observed during data collection for QA test form.
6. Set alarm limit at 60% of flow observed during data collection for QA test form.
27
Table 4.6 ECM-100 Timer Settings
Timers (Menu 03) Range Factory Preset
RO PUMP DELAY 1 - 99 sec1 6 seconds
START-UP PERM DIVERT 0 - 99 min 2 minutes
AUF PERIOD 0 - 99 hr 1 hour
AUF DURATION 0 - 99 min 6 minutes
ALARM SHUTDOWN 0 - 99 sec 15 seconds
DELAY
LOG PERIOD 0 - 99 hr 1 hour
AUTO-ON PERIOD 0 - 99 hr (see note 2)
AUTO-ON DURATION 0 - 99 min (see note 3)
1. An RO pump delay of 0 will disable the RO pump.
2. If used set to 4 hours.
3. Set duration to 15 minutes.
28
GND WHITE
48
5
RED
47 2
BLACK 4 COMMUNICATION CABLE RS-232, 1200 BAUD, (WORD FORMAT: 4
46 1
3
8-N-1), WITH 9-PIN FEMALE D-SUB CONNECTOR
GREEN
45
44 pH SENSOR
OPTIONAL PRETREATMENT LOCKOUT CONTACT ±414 mVDC SIGNAL
43 5
(CLOSED = "ON")
+5VDC
42
GND OPTIONAL PERMEATE STORAGE TANK BNC
41 2 3 pH INPUT
LOW LEVEL SWITCH
+5VDC (CLOSED=LOW "START RO")
40
GND
39 OPTIONAL AUX CONTACT pH SENSOR
+5VDC (CLOSED = "ON") 6 SOLUTION GROUND/SHIELD WIRE
38
RED +5VDC pH SHIELD
37
BLACK SIGNAL/PULSE 0-5 VDC CONCENTRATE FLOW SENSOR
36
(0.25-260 GPM)
WHITE GND
35 NOTES:
RED +5VDC
34
BLACK SIGNAL/PULSE 0-5 VDC PERMEATE FLOW SENSOR 1 CONNECT TO SERIAL PRINTER OR PC PORT FOR DATA DOWNLOAD, MAY ALSO
33
(0.25-260 GPM) BE CONNECTED TO A PARALLEL PRINTER VIA "SERIAL/PARALLEL CONVERTER
WHITE GND
32 BOX" (SUCH AS AVAILABLE FROM RADIO SHACK).
31 AUXILIARY #2
INPUT 4
30 (NOT USED) 2 TO WATCH FOR AN EMPTY FEEDWATER TANK RATHER THAN A FULL STORAGE
29 NO CONNECTION TANK, SWAP HIGH & LOW LEVEL SWITCH CONNECTIONS AND REVERSE
29
BLACK GND TO #17 & #18. CLOSED INPUT = RO "ON/RUN", OPEN INPUT = RO "OFF".
26
WHITE DRIVE SIGNAL LEVEL CONTROL CONTACT TO BE DRY "NON-POWERED", COMPATIBLE WITH
25 5VDC SIGNAL.
FEED CONDUCTIVITY
GREEN GND & TEMPERATURE SENSOR
24
(5-2000 uS/CM AND 0-150˚ F)
RED TC ELEMENT
23 4 VERSION 2 MAIN BOARD USES SOFTWARE REV. G OR HIGHER AND USES BNC CONNECTOR
RED +5VDC +SUPPLY FOR DIRECT CONNECTION OF PH SENSOR. AUXILIARY 2 INPUT IS FOR FUTURE OPTIONS.
22 4
GREEN 0-50 mVDC +SIGNAL
21 1 POST-FILTER PRESSURE
WHITE -SIGNAL 3 TRANSDUCER
20 5 PRETREATMENT DEVICE MUST HAVE NO DRY "NON-POWERED" CONTACTS, COMPATIBLE WITH 5VDC SIGNAL.
(0-100 PSIG)
BLACK -SUPPLY ALL MUST WIRED IN PARALLEL BACK TO TERMINALS 42 AND 43.
19 2
OPTIONAL
GND
18 PERMEATE STORAGE TANK
2 3
+5VDC HIGH LEVEL SWITCH 6 PROVIDES SIGNAL FOR TRANSFER PUMP CONTACTOR THAT RUNS ONLY WHEN 23G RO RUNS.
17 (OPEN=HIGH "RO OFF")
RED +5VDC +SUPPLY
16 4
GREEN 0-50 mVDC +SIGNAL
15 1 FINAL PRESSURE
WHITE -SIGNAL 3 TRANSDUCER
14
(0-500 PSIG)
BLACK -SUPPLY 2
13
L3 T3
30
NC 3 ADJUSTMENT, CLOSED LOOP
7 CONTROL, DISABLED DURING CIP)
2 INCOMING POWER CORD PLUG SHOULD BE CONNECTED
TO RECEPTACLE HAVING A PROTECTIVE EARTH GROUND. C
6
RED
NO A2 A1 WHT CIP PUMP STARTER
5 2M
2
3 IF THE COMMON JUMPERS ON TB3 NEED TO BE MODIFIED NC
FOR AN ALTERNATE CONFIGURATION, NOTE THAT ONLY 4 OPTIONAL
TERMINALS 10-12 AND 22-27 CAN BE CONNECTED AS DRY C
3
CONTACTS. TERMINALS 1-9 AND 13-21 MUST ONLY BE 1 1OL
NO BLK 96 A2 A1 WHT RO PUMP STARTER TB5
CONNECTED TO HIGH VOLTAGE (L1, L2) POWER. 2 1M
2
NC
1
4 THE L1 & L2 OUTPUT TERMINALS OF TB7 ARE FUSED. 2
HOT
THEREFORE, THE WIRING FROM THE L1 & L2 TERMINALS
OF TB7 CAN BE 20AWG OR LARGER.
TB7 4
WHT NEUTRAL WHT
L2 2 L2 OR
5 BLK NEUTRALS OF OUTPUTS (JUMPERED)
DRAWING OS1125748. L1
1
GRN
6 TERMINAL NUMBERS ABOVE LINE,
GND
WIRE NUMBERS BELOW LINE. (FUSED OUTPUT)
TB6
B B INCOMING
POWER
C C
D D
ECM
4.4
SYSTEM OPERATIONS
MENU
(MAIN SCREEN)
4.4.1
03 04 07
01 02 05 06
TIMER ACCUM MAINTE-
DATE & TIME ALARM LIMITS LOG TABLES CALIBRATION
PRESETS HOURS NANCE
08
ECM-100 Display Screens
PRINT CUR-
RENT VALUES
31
09
ECM Display Screen Hierarchy
METRIC/US
SELECT
10
PERM HIGH
COND ALARM
11
FACTORY
SETTINGS
12
AUTO-ON
TANK FULL
13
COMM PORT
SPEED
4.4.2 Detail of Date and Time Operation (Menu 01)
ENTER HOUR
Passcode:
ENTER MINUTE
Store Changes:
ENTER YEAR
ENTER WEEKDAY
(1 = SUNDAY)
32
4.4.3 Detail of Alarm Limits Operation (Menu 02)
pH ENTER SETPOINT
HIGH2 0 - 14
pH ENTER SETPOINT
LOW 0 - 14
33
4.4.4 Detail of Timer Presets Operation (Menu 03)
The time from when the inlet valve opens until the high
RO PUMP DELAY2
pressure pump starts (at machine ON, and after tank full or
(SECOND)
pretreatment lockout).
AUF PERIOD How often the Autoflush comes on (typically every 1 hour),
(HOUR) based on “run hours” timer.
ALARM SHUTDOWN
The amount of time which certain alarms will sound before
DELAY
shutting down the machine (See Section 4.6.3).
(SECOND)
LOG PERIOD How often the current display readings are saved to the
(HOUR) History Log and sent to the RS-232 printer/computer.
How often the machine will start up automatically when OFF (in
AUTO-ON PERIOD*
AUTO mode), based on “off hours” timer. To prevent stagna-
(HOUR)
tion overnight and on weekends (typically every 4 hours).
AUTO-ON DURATION* The amount of time that the machine stays on during an
(MINUTE) AUTO-ON cycle (typically 15 minutes).
34
4.4.5 Detail of Accumulated Hours Operation (Menu 04)
04 ACCUM. HOURS
RUN HOURS
OFF HOURS
35
4.4.7 Detail of Calibration Operation (Menu 06)
ENTER 1 TO ENABLE
pH ENTER 0 TO DISABLE
ENTER OFFSET
POST-FILTER PRESSURE
-99 to +99
ENTER OFFSET3
PRIMARY PRESSURE
-99 to +99
ENTER OFFSET3
FINAL PRESSURE
-99 to +99
ENTER OFFSET2
PERMEATE PRESSURE
-99 to +99
ENTER OFFSET 4
CONC FLOWRATE OFFSET
-99 to +99
ENTER OFFSET4, 6
PERM FLOWRATE OFFSET
-99 to +99
ENTER OFFSET5
CONC FLOWRATE SLOPE
0 to 255
ENTER OFFSET5
PERM FLOWRATE SLOPE
0 to 255
ENTER pH x 10
pH LOW CALIBRATE7
0 to 140
1 Adjustment ranges remain the same whether in U.S. or Metric units; the settings are dimensionless.
2 Each offset unit for 100 psi sensors is equal to 0.50 psig (0.0345 bar).
3. Each offset unit for 500 psi is sensors is equal to 2.0 psig (0.138 bar).
4 The standard 1-inch flow turbine should be calibrated with a flow offset of zero. Each offset unit equals 0.0264 gpm (0.1 Lpm).
5 The “slope” for both flows should be set to 36 +_ 2 for 1-inch turbines. The slope has units of Lpm/(100 turbine revolutions).
6 Setting the Flow Offset to 99 will force the flow readings to 0.1 to temporarily by-pass a failed flow sensor or turbine until
replacement is installed.
7. To calibrate pH, the passcode must be entered separately for each item, and the pH electrode must be put in two different pH
reference solutions (4.0 for Low and 10.0 for High, or 4.0 and 7.0, or 7.0 and 10.0).
8. Pressure offsets are for field personnel to easily enter minor adjustments to the operating pressure readings without recalibrat-
ing and are used to temporarily “dial-out” a transducer that is beginning to fail, in order to keep the machine running until the
sensor can be replaced. Adjustment of these offsets reduces the accuracy of the readings throughout their operating range.
36
4.4.8 Detail of Print Current Values Operation (Menu 08)
07 MAINTENANCE MENU
07 MAINTENANCE MENU
09 METRIC/US SELECT
07 MAINTENANCE MENU
37
4.4.11 Detail of Factory Settings Operation (Menu 11)
07 MAINTENANCE MENU
11 FACTORY SETTINGS
FACTORY SETTINGS
SAVE
-OR-
07 MAINTENANCE MENU
PASSCODE REQUIRED
12 AUTO-ON TANK FULL MENU
PERM-DIVERT/OVERFLOW SHUTDOWN
07 MAINTENANCE MENU
PASSCODE REQUIRED
SELECT COM PORT SPEED
38
5.0 MACHINE OPERATION AND MAINTENANCE
Proper maintenance of the 23G RO system in accordance with this manual and good medical
practices is essential when the system is used in a medical application for water purification for use
in hemodialysis. FAILURE TO FOLLOW THE REQUIREMENTS SET FORTH IN THIS SECTION
AND GOOD MEDICAL PRACTICES COULD POSE A RISK OF SERIOUS INJURY OR DEATH TO
HEMODIALYSIS PATIENTS.
Osmonics 23G RO systems have been designed to operate with a minimum of operator attention.
Like all mechanical systems they will operate longer and with less trouble when routine maintenance
is performed regularly. Maintenance on an Osmonics reverse osmosis system is typically limited to
completing performance logs, cleaning, flushing, sanitizing, changing pre-filters, regular maintenance,
and replacement of damaged or failed parts. The maintenance procedures are as follows: (specific
instructions follow the maintenance schedule).
There are seven preventative maintenance procedures which must be performed on a regular basis:
1. Maintain the pH buffer system (if applicable).
2. Changing the pre-filter cartridges.
3. Flushing the machine.
4. Verifying product water quality.
5. Cleaning the machine with approved Osmonics cleaners.
6. Sanitizing the machine with approved Osmonics sanitizing agents.
7. Cleaning and checking calibration of pH and conductivity probes.
5.1 Daily Requirements
NOTE: Allow water temperature to stabilize before attempting to record results. This
prevents errors due to fluctuating temperatures.
Operating performance data should be recorded daily and kept on file and submitted to your
equipment supplier or Osmonics Daily log sheets are included in the instruction manual
package and are useful for recording performance data. In addition, data automatically stored
by the ECM-100 can be downloaded to a printer or computer to facilitate and simplify
record keeping. Copies of Osmonics Daily log sheets will be required by Osmonics if a
warranty question arises.
WARNING: Determination of microbial culturing and disinfection frequency
is the responsibility of the operating facility. Failure to conduct
timely microbial culturing and disinfection could pose a risk of
serious injury or death to hemodialysis patients.
1. Observe and record hardness level in the feedwater to the RO (for systems with softener
pretreatment).
NOTE: Check the softener output for hardness at the beginning of each day and at
the end of each operational day to confirm adequate softener capacity. The
hardness level should be less than 1 grain per gallon (GPG).
2. Observe and record salt level in brine tank (for systems with softener pretreatment).
3. Observe and record Total Chlorine (Chlorine/Chloramine) concentrations in the
feedwater of the RO. Follow instructions included in each test kit.
WARNING: Take corrective action or contact the equipment supplier if any
pre-treatment device fails to provide adequate treatment of feed
water.
4. Allow water temperatures to stabilize before recording Osmonics Daily log sheet data.
39
5. Observe and record the pre-filter inlet and post-filter outlet pressure gauges on the
Operation Log. The difference in the pressure values will measure the condition of the
pre-filter cartridge. When the pressure differential (delta P) doubles above the clean
delta P, the cartridges need to be changed. Refer to Section 5.9 for pre-filter cartridge
replacement procedure. Change out frequency is at least weekly.
6. Observe and record primary and final pressures on the Operation Log.
7. Observe and record the concentrate (reject) and permeate (product) flow rates on the
Operation Log. Allow water temperatures to stabilize before attempting to record
results, to prevent errors due to fluctuating temperatures.
8. Observe and record the percent rejection and permeate conductivity displayed on the
ECM-100 display.
9. Measure and record the feed water temperature on the Operation Log. A hand held
thermometer may be used. The water temperature has a significant effect on the flow
rate of the RO membrane.
10. Flushing
The machine should be flushed daily to remove sediment from membrane surfaces. For
flushing during on-line operation all Osmonics’ 23G machines are equipped with an
Autoflush feature, which automatically increases the concentrate flow rate on an
intermittent basis.
5.2 Weekly Requirements
The actions below should be performed in addition to the daily requirements.
1. Replace pre-filters weekly or when pressure drop doubles from new conditions. Refer to
pre-filter replacement procedure (Section 5.9).
2. Observe and record the permeate conductivity using a hand held/independent meter.
Recalibrate ECM-100 as necessary.
3. Observe and record inlet pH. Recalibrate ECM-100 as necessary.
5.3 30 - 60 Days Requirements
The actions below should be performed every 30 to 60 days.
1. Clean/sanitize the membrane elements. Refer to Section 5.6 for the membrane cleaning/
sanitizing procedure.
40
4. Check the valves for correct operation.
5. Check the tubing and fittings for leaks or wear.
6. Check the switches and lights for correct operation.
5.5 Flushing
NOTE: If the machine is to be turned off for more than 4 hours, it should be
programmed to flush to drain for 15 minutes every 4 hours. This should
minimize the growth potential of biological components in the machine. An
AUTO-ON period can be set in the timer Preset Menu (03) of the ECM-
100 to prevent water from stagnating. Menu (12) must also be set to
permeate divert.
The machine should be flushed daily to remove sediment from membrane surfaces. For
flushing during on-line operation, all Osmonics’ 23G machines are equipped with an
Autoflush system, which automatically increases the concentrate flow rate on an
intermittent basis.
1. To manually flush the unit, open the machine concentrate valve so the concentrate flow
rate is 20 to 30% higher than during normal operation. Operate for 10 to 20 minutes and
close concentrate valve.
CAUTION: Do not operate the machine with more than 30% additional
concentrate flow without prior approval from Osmonics. Operation
above this flow rate may damage the pump and motor.
2. Use the AUTO-ON commands in the Timer Presets Menu (03) of the ECM-100, to flush
the machine automatically during extended shutdown periods (over 4 hours). If using the
AUTO-ON command, the machine must be in the AUTO mode. The AUTO-ON-
ACTIVE LED will illuminate when the AUTO-ON period and duration timers are set
above zero.
5.6 Step-Wise Cleaning
NOTE: Osmonics recommends sanitizing your machine after cleaning.
Foulants such as minerals, silt, and organic substances may collect on the membrane element
surface and cause the membrane element to foul and diminish in its function. Many of these
foulants are prevented by proper selection of pre-treatment equipment, while others are
treatable with more sophisticated designs. Regardless of the foulant, it is essential to clean
the membranes promptly once cleaning is indicated. The longer a foulant is allowed to
remain in contact with the membrane element, the more difficult it will be to remove.
Routine cleaning of the membrane elements in conjunction with regular sanitizing and
flushing will keep bacteria counts at a minimum and membrane element performance at its
best. Cleaning removes the silt, organic, and mineral deposits that collect on the membrane
surface, which if left untreated, encourage bacteria growth. It will eventually impair the
membrane elements’ ability to perform.
There are a variety of indications for cleaning membranes. The most common is a reduced
product flow rate. Remember that a reduction in inlet water temperature can also result in
a reduced flow rate. Refer to the “Temperature Correction Factor” (Technote 113) to
determine the reduction in flow that can be attributed to reduced water temperature. Clean
the membranes whenever the temperature compensated flow rate drops by 10%. A loss in
the membrane performance (percent rejection) or increase in TDS of the product water may
also be an indication to clean the membranes. Observation of the decrease in either
permeate flow rate or salt rejection, or an increased pressure drop across the machine also
indicates when cleaning is required. A good preventative maintenance practice is to clean the
membranes every 30 - 60 days, and more often if needed.
41
NOTE: Cleaning may be required as often as once every week or infrequently as
once every two months, depending upon the local water supply conditions.
For more information, or for instructions on long-term machine shutdown (greater than 72
hours), contact your equipment supplier.
Read and understand all instructions prior to beginning procedure.
CAUTION: RO units must be rinsed to drain, with normal pressures for a minimum of
8 hours prior to first exposure to disinfectants or irreversible damage may
occur to sepralators. This includes start-up of machines with new
membranes and membrane element replacements.
WARNING: Follow all Material Safety Data Sheet (MSDS) precautions and
Occupational Safety and Health Administrating (OSHA)
standards when introducing a chemical (i.e., cleaning and
sanitizing agents).
A typical CIP system includes a tank, pump, connecting hoses which are connected to the
machine in a manner that allows a closed loop for recirculation of cleaning solutions. Contact
your equipment supplier for assistance in designing, installing, and implementing a suitable
CIP system.
CAUTION: Prior to sanitizing, a thorough cleaning with AD-20 or similar product is
required to avoid membrane damage.
To circulate the cleaning solution through the machine, use non-collapsible hose piped to
feed the machine from the CIP tank through the CIP pump.
5.6.1 Installation of the 23G CIP
1. Remove cover on tank and remove the Clean-In-Place (CIP) hoses and fittings.
2. Remove plugs on feed, permeate, and concentrate CIP ports on right side of the
23G. Install the valves and quick release fittings provided.
3. Hook up the CIP feed hose to the quick connect fitting on the pump. Hook the
other end of the hose to the quick connect fitting on the CIP tank.
4. Place the CIP skid near the 23G so all CIP lines will reach CIP ports on the machine.
5. Connect the feed permeate and concentrate lines to the CIP tank quick connect on
CIP pump and then to the CIP port on the machine. Open the CIP valves on the
machine.
5.6.2 Cleaning/Sanitizing with 23G CIP
1. Start the 23G and allow the permeate to fill the 23 skid tank to the desired level. Turn
machine off by pushing the Off button on the ECM-100 controllers.
2. Add and mix desired amount of cleaner or sanitizer to the CIP tank.
3. Mix chemical cleaning solution in a suitable (clean) tank with purified water. RO
permeate is best. Use the following to determine cleaning solution volume:
42
4. Remove the feed CIP line from the quick connect fitting on the side of the CIP pump.
Connect it to the quick connect fitting on the CIP feed port on the side of the 23G.
5. Connect the concentrate CIP line to the quick connect port on the CIP skid. Attach
the other end to the quick connect concentrate CIP port on the 23G.
6. Close the feedwater valve which provides water from pretreatment to the machine.
7. Close the permeate and concentrate outlet valves on the back side of the front
panel.
8. Then connect the long cord from the starter box on the CIP skid to the pigtail bell
fitting on the back side of the controller box.
9. Connect 115 volt power to the Medical cord, located on the starter box on the CIP
skid.
10. Return the ECM-100 controller and push the HAND/AUTO button to HAND. The
Hand Mode light will illuminate. Push the On button, and both the 23G pump and
the 23G skid pump will start. See Cleaning in the 23G Operator’s Manual for
cleaning instructions.
NOTE: The CIP system must provide positive feed pressure to the RO
machine. Osmonics strongly recommends using a CIP pump to provide
sufficient inlet pressure (20 - 30 psi [1.38 - 2.07 bar]) to the high-
pressure RO pump during cleaning. Failure to provide adequate inlet
pressure will damage the RO high pressure pump.
11. In between cleaning processes rinse out the CIP container by following step 3 above.
Fill and drain the tank several times to rinse the cleaner or disinfectant out of the
CIP container. After allowing the tank to fill, turn off the 23G. Empty the tank by
removing the CIP hose from the CIP feed port on the 23G. Allow the tank to empty
out to a floor drain.
12. After rinsing the tank well, the CIP skid is ready for further cleaning/sanitizing or for
storage.
13. Recirculate the cleaning solution at the same flow rate and pressure used for
flushing.
NOTE: It is best to clean at elevated temperatures, but lower temperatures
will suffice. DO NOT allow cleaning temperature to exceed 95° F
(35° C). The ECM-100’s high temperature alarm is factory preset at
105° F (41° C).
14. Recycle the cleaning solution for approximately 15 minutes or until the solution
temperature reaches 90° F (31° C). If heat rise occurs too quickly, larger volumes of
cleaning solution or use of a heat exchanger will allow the temperature rise.
15. Turn the machine OFF and allow the cleaner to soak for 20 minutes.
16. If applicable, turn the CIP pump control circuit OFF.
CAUTION: Do not leave cleaning solution in the machine for a period longer
than one hour. The cleaning solution may damage the membranes
and the machine during an extended period of contact.
17. To flush the cleaner from the machine close the CIP inlet valve.
18. Open the inlet feed valve.
19. Open the CIP tank drain valve.
20. Permeate and concentrate will continue to flow to the CIP tank and then to the
drain.
21. Operate the machine as described in Steps 18 - 20 for 30 - 60 minutes.
43
22. The cleaner is sufficiently flushed-out when the feed pH and permeate conductivity
are restored to nearly their previous levels. Typically, chemical test kits may also be
used to verify the absence of chemical residual.
23. To return the machine to service, open the permeate valve.
24. Open the concentrate valve.
25. Close the CIP permeate valve.
26. Close the CIP concentrate valve.
27. Press the OFF key on the ECM-100. The CIP LED light will turn off.
28. Install new pre-filters.
NOTE: Osmonics recommends sanitizing machine after cleaning. Proceed to
sanitizing (Section 5.7).
29. Place the machine in AUTO mode by pressing the HAND/AUTO key. The AUTO
LED light will illuminate.
NOTE: The RO must be operated in AUTO mode in order to respond to float
switches, pretreatment and other alarms.
5.7 Sanitizing Using a CIP System
WARNING: Determination of microbial culturing and disinfection frequency
is the responsibility of the operating facility. Failure to conduct
timely microbial culturing and disinfection could pose a risk of
serious injury or death to hemodialysis patients.
CAUTION: RO units must be rinsed to drain with normal pressures for a minimum of
8 hours prior to first exposure to disinfectants or irreversible damage may
occur. This includes start-up of machines with new membranes.
WARNING: Follow all MSDS precautions and OSHA standards when
introducing a chemical (i.e., cleaning and sanitizing agents).
Sanitizing frequency may be reduced by running the machine continuously. If the machine
must be turned off for more than 4 hours, it should be programmed to flush to drain for
15 minutes every 4 hours. This should minimize the accumulation of bacteria onto
membrane surfaces. An AUTO-ON period can be set in the Timer Menu (03) of the ECM-
100 to minimize the potential of water from becoming stagnate.
NOTE: The Pretreatment Lockout and Tank Level Full signals will override the
AUTO-ON feature.
Performing a regularly scheduled sanitizing procedure for the machine may be required to
control bacterial growth. The machine must be cleaned and pre-filters changed prior to
sanitizing for greatest effectiveness. A 1% peracetic acid-based disinfectant, or 0.5%
formaldehyde are typically used.
Peracetic acid-based sanitizers are oxidants, and PA membranes are sensitive to oxidants.
The presence of transitional metals such as iron on the membrane will catalyze this oxidation
reaction, leading to rapid membrane performance degradation. The use of peracetic acid-
based chemicals is acceptable under the following conditions:
• Prior to peracetic acid-based chemical use, the membrane is cleaned with a low
pH cleaner to free the membrane of iron and other transitional metals.
• The peracetic acid-based chemical solution is mixed with water free from iron
and other transitional metals. RO water is preferred.
• The peracetic acid-based chemical solution temperature is kept at or below
77° F (25° C). Ice or other cooling methods may be required to keep temperature
down.
44
• The PA membranes’ exposure to the peracetic acid-based chemical solution
does not exceed one hour per week at a chemical solution concentration of
≤1%.
CAUTION: Prior to sanitizing, a thorough cleaning with AD-20 or similar product is
required to avoid membrane damage.
The 23G machine has a CIP feed port into which sanitizing solution can be fed from a CIP
tank and pump. In this case, sanitizing can be accomplished with the same procedure used
for cleaning.
Refer to Section 5.6.2 Cleaning/Sanitizing with CIP.
5.8 Membrane Element Cleaners and Sanitizers for 23G Machines
Osmonics offers a full line of chemical cleaners and sanitizers for specific cleaning needs.
*Maximum contact time for all sanitizers is equivalent to one hour/week at the
recommended dosage. Contact Osmonics for prices and application instructions.
45
5.9 Pre-Filter Replacement Procedure
Five micron pre-filters are factory-installed to protect the high-pressure pump, membranes
and valves from particles in the feedwater.
The pre-filter cartridges should be replaced regularly to minimize pressure drop and help
minimize biological growth. Weekly replacement is typical. An increase in pressure drop
across the filter indicates the pre-filter cartridges need changing. Use only Osmonics
approved filters rated for 5 microns or less. Do not attempt to clean used pre-filters.
The pre-filters should be replaced before and after cleaning or sanitizing of the membranes
elements.
1. To change the pre-filter, turn the water supply off. The pre-filter inlet and outlet gauges
should read zero psi.
2. Remove the pre-filter bowl by rotating it counterclockwise.
3. Remove the old filter.
4. Install the new filter.
5. Re-install the pre-filter bowl.
NOTE: Failure to change pre-filters may void machine warranty.
5.10 Recording Performance Data
Operating performance data should be recorded daily and kept on file or submitted to your
equipment supplier or Osmonics. Copies of data sheets will be required by Osmonics if a
warranty question arises. Daily Log sheets are included in the instruction manual package
and are useful for recording performance data. In addition, data automatically stored by the
ECM-100 can be downloaded to a printer or computer file to facilitate and simplify record
keeping. Refer to Section 6.6.
In addition to the date, time and 10 “on-screen” performance data readings, the ECM-100
will also download a record of permeate pressure and an alarm code. The alarm code
provides a record of what causes machine shutdown conditions. See Section 6.6 for
downloading data.
NOTE: Copies of the logs should be submitted to your equipment supplier.
5.11 Preparing Machine for Movement
Contact your equipment supplier for moving, storage and shipping instructions.
5.12 Membrane Element Replacement
As time progresses, the efficiency of the membrane elements will begin to decline. Generally,
the salt rejection of the membrane will not change significantly when properly operated on
water until about two years after installation. Under ordinary conditions, the permeate rate
may decline slightly after one to two years of operation. This period can be extended with
frequent flushing and cleaning as outlined in these instructions.
If the membranes are to be saved, they must be cleaned and then sanitized before removal
from the machine.
5.12.1 Membrane Element Removal
1. Disconnect the permeate tubing from the permeate manifold.
2. Remove the end cap and housing adapter from the membrane element housing.
3. Remove the membrane element from the membrane element housing.
4. Inspect the membrane element housing. Clean as necessary to remove any
contaminants, obstructions, etc.
46
5.12.2 Membrane Element Installation
CAUTION: Membrane elements are packaged with a small amount of biocide
solution to prevent biological growth. Provide adequate ventilation
and use protective gloves and eye protection when handling.
Membrane elements must be kept moist at all times in order to
prevent possible damage to the membrane material.
CAUTION: Upon start-up of a new machine or installation of new membranes
machine must be operated with permeate running to drain for a
period of 8 hours in order to flush out all membrane preservatives.
Failure to properly flush the membranes can result in patient safety
issues.
NOTE: New membranes may produce 10 - 15% higher permeate flow than
specified. Slight adjustment of recycle and concentrate orifice may be
required to reduce flow rate.
1. Remove the new membrane element bag containing the membrane element from
the shipping tube.
2. Cut the bag open as close as possible to the seal at the end of the bag so that
the bag may be reused for disposal of the old membrane element.
3. Remove the membrane element from the bag and remove the foam protectors
from each end of the membrane element. Set membrane aside in a clean space
and continue.
4. New O-rings should be installed when membranes are replaced. Make sure that
all parts are clean and free from dust and dirt. Examine O-rings for nicks or cuts
and replace if damaged.
NOTE: O-rings are not included with membrane elements. See Spare
Parts List to order new O-rings.
5. Locate the concentrate seal holder on one end of the membrane element, and
place the U-cup” concentrate seal (brine seal) into the groove of the
concentrate seal holder with the open side of the U-cup facing away from the
membrane element body. Note new direction of flow. The open side of the
U-cup is on the upstream end of the membrane element.
47
Victaulic Clamp
Endcap Assembly
w/Load Transfer Device
Direction of Flow
O-Rings (2)
O-Rings (2)
Plug/Adapter
48
C
M M R
B
A
S
N P
LEGEND
A ENDCAP W/ LTD
B INTERBANK PLUG
F O-RING
D C INTERBANK PLUG
L D INTERCONNECTOR
E E O-RINGS
F CONCENTRATE SEAL
F G PLUG/ADAPTER
K
J PLUG
J H LTD
K MEMBRANE ELEMENT
L PERMEATE TUBE
M PERMEATE
N FEED
P CONCENTRATE
H R 4" CLAMP GASKET
G S 3/4" CLAMP GASKET
Figure 5.10 Cross Sectional View Membrane Element and Housing Flow
11. Insert an interconnector into the permeate tube located closest to the open end
of the housing.
12. Install the end cap and affix the closure device.
13. Reconnect the permeate tube to the permeate manifold.
14. Repeat for other membrane elements as necessary.
15. Before putting the machine back into normal operation, run the permeate and
concentrate streams to drain for at least 8 hours. This is done to ensure that all
the preservatives have been removed from the membrane elements and prevent
irreversible damage.
Machine is ready for normal operation, however do not put into service until all
applicable water tests have been completed.
In order to ensure that the RO is performing at or above AAMI standards, it is
necessary to perform an AAMI Water Quality Analysis Test. For new units, the RO
must be operated (rinsed to drain) for at least two hours before taking a sample, to
ensure that the membranes are free of preservatives or other contaminants which
would invalidate the test.
NOTE: Follow the procedures recommended by your water quality testing
laboratory.
49
5.13 Flow Control Adjustments
NOTE: Prior to any adjustments, make sure that temperature is constant, AUTOFLUSH
is off, and concentrate valve is closed.
Refer to Figure 5.10, Flow Control Manifold.
CAUTION: The flow control orifice valves are sealed to prevent tampering, and should
not be adjusted by unauthorized personnel. Damage to the machine may
occur and physical injury is possible.
• The flow control orifices are factory set; according to the design specifications of the
machine.
• Adjustment of the orifices in the field are permitted only with the approval of the
equipment supplier.
• Permeate flow rates which exceed design specifications will shorten the life of the
membranes, degrade the quality of the permeate output, and may cause injury to dialysis
patients.
CAUTION: The large orifice nuts at the base MUST NEVER be turned.
• The large nuts must remain in the position set at the factory; with the 4 dimples from
both nuts lined up with each other in a straight line (longitudinal with the block).
• Tightening these nuts (even by a small amount) will cause damage to the O-ring located
under the nuts.
• Over-tightening the locking nuts will damage the threads and may cause leaking the next
time that the orifice is adjusted.
CAUTION: Improper adjustment of the flow control orifices can cause serious damage
to the machine, and/or personal injury.
5.13.1 Leaks
During adjustment it is normal for a very small amount of water to leak from under
the larger nut of the orifice, and/or from around the locking nut on the orifice
adjustment screw.
• To correct leaking under the large nut, the two O-rings need to be replaced.
Contact your equipment supplier for assistance.
• Any other leaks on the machine should be corrected promptly. Any cracked or
broken fittings must be replaced. Contact your equipment supplier for
assistance.
50
NOTE: There is a large amount of interaction between the concentrate valve and
the two orifices. Make sure concentrate valve is closed during orifice
adjustment. Adjusting one of them will affect the setting of the other. To
change the permeate or concentrate output of the machine, both orifices
will usually need to be adjusted in small amounts, alternating between the
two several times, until the correct settings are reached.
Concentrate Manifold
from the “last” membrane housing
Recycle Orifice
Autoflush Valve
To Concentrate Outlet
Machine Concentrate
Valve
Do not make adjustments when the Autoflush light is ON. Always wait until the
Autoflush finishes and the light goes out before adjusting the orifices. Make sure
concentrate valve is closed.
16. Concentrate Orifice - screwdriver adjustment.
• Adjusts the concentrate flow output to the drain.
• Adjust so that the concentrate flow rate matches the value printed on the
machine nameplate. To adjust the concentrate flow rate:
Adjusting the Orifices - requires two wrenches and a large screwdriver.
a. Use one wrench to hold the large nut and prevent it from turning.
b. Use another wrench to loosen the locking nut, adjust the flow with the
screwdriver.
51
c. Tighten the locking nut after.
• While adjusting, make sure that the primary pressure reading is less than
275 psi (19.0 bar), and more than 150 psi (10.3 bar).
• Clockwise (in) reduces the concentrate flow rate, causing higher primary
pressure and higher permeate flow.
• Counterclockwise (out) increases the concentrate flow rate.
WARNING: Be careful not to unscrew the adjustment too far, or
the screw will blow out of the orifice and may cause
injury.
17. Recycle Orifice - screwdriver adjustment.
• Controls the amount of concentrate being recycled back to the pump.
• Adjusts the primary pressure and permeate flow rate.
• Adjust so that the permeate flow rate matches the value printed on the
machine nameplate. To adjust the permeate flow rate:
Adjusting the Orifices - requires two wrenches and a large screwdriver.
a. Use one wrench to hold the large nut and prevent it from turning.
b. Use another wrench to loosen the locking nut, adjust the flow with the
screwdriver.
c. Tighten the locking nut after.
• While adjusting, make sure the pump boost pressure (primary pressure
less pre-filter pressure) reading never goes outside of value listed in
Section 1.8.4.
• Clockwise (in) increases primary pressure and permeate flow rate.
• Counterclockwise (out) reduces primary pressure and permeate flow
rate.
WARNING: Be careful not to unscrew the adjustment too far, or
the screw will blow out of the orifice and may cause
injury.
It may be necessary to adjust orifices several times to attain the proper
settings.
Occasionally the permeate flow rate output of the machine is too high, and
cannot be adjusted low enough, even when the recycle orifice is all the way
open (unscrewed nearly all the way out). This condition most often occurs
right after the membranes have been replaced, and indicates that the
permeate rate characteristic (flux rate) of one or more of the membranes
may be abnormally high.
• If the permeate conductivity reading is also abnormally high (% rejection
is low), the problem is most likely caused by a bad O-ring seal in one of
the membrane housings.
• If the % rejection reading is normal or higher than normal, then the
membranes are good, but one or more has a water product rate at the
high end of product specification range. Contact your equipment
supplier for assistance.
5.14 Permeate Divert
Factory-installed valves divert the RO permeate to drain for a preset period of time upon
machine start-up or when the RO permeate exceeds a preset conductivity level. This
optional feature ensures good quality water flows to storage or to points of use. A start-up
divert timer setting in the timer presets menu of the ECM-100 controls the duration of
permeate divert each time the machine starts up. A high conductivity level is set in the Alarm
52
Limits menu so that permeate is diverted should the conductivity exceed that level. The
divert mode can be disabled if desired by setting the start-up permeate divert timer to zero
and selecting WARNING ONLY or SHUT DOWN from the permeate high conductivity
alarm function menu (10).
5.15 Product Water Pressure Relief
The factory-installed product water pressure relief hardware includes two 1/4-inch
thermoplastic pressure relief valves which relieve excessive permeate backpressure based on
a set point. Backpressure can be the result of pressurized storage tanks, pressurized
distribution loops, restrictions in permeate plumbing and/or other factors which prevent
permeate from flowing from the machine. The valves are typically factory preset to 60 psi
(4.1 bar).
Allowing the machine to operate with permeate pressure greater than 60 psi (4.1 bar) may
cause premature failure of the respective diaphragm valve. The diaphragm valve is a
“normally closed” valve that is designed to fail in the closed position, as required for normal
(non-divert) operation. Should this valve fail, the machine will operate in the normal mode
with permeate flowing to the tank/distribution loop.
53
6.0 FEATURES AND ACCESSORIES
Accessory connections are provided on both the input and output terminal strips of the
ECM-100. Accessory outputs can be used to control chlorine or dispersant feed pumps;
accessory inputs can be used to control pre- or post-treatment equipment. The output
connections are switched by relays and power to the outputs will be shut off if machine is
turned off due to an alarm condition.
The ECM-100 allows you to connect to a printer and a personal computer. These features
allow you to store and print data on the 23G’s current and historical performance.
6.1 Level Controls
Float switches pressurized storage tank switches or other level controls may be connected
to the ECM-100’s tank level control inputs. To recognize the tank level status, the ECM-100
must be in the AUTO mode.
A level control system with “one” input signal may be connected to the ECM-100 across
terminals 17 and 18 of the main strip. Terminals 40 and 41 must be jumpered together in this
case. An open status will shut down the machine and a closed status will allow it to run.
CAUTION: The level control contacts must be dry, non-powered, and compatible with
5 V signals.
NOTE: The level control feature of the ECM-100 can be configured for two inputs - a
high level (tank full) switch and a low level switch. If properly connected, when
both switches open, the ECM-100 will shut down the machine and illuminate
the blue Tank Full LED light. As the level in the permeate storage tank drops,
the high level switch will close but the machine will remain locked-out until the
tank level drops to the height that causes the low level switch to close as well.
When both switches are closed, the ECM-100 will restart the machine. As the
level in the tank rises and the low level switch opens, the machine will continue
to run. Only when the high level switch opens will the machine shut down. To
utilize the two input configuration, connect the level controls to terminals 17
and 18 and terminals 40 and 41. See Figure 1.3 for connection points.
It is possible to connect the high and low level switch inputs in reverse positions on the
ECM-100 terminal strip to achieve level control of a feed water ballast tank. In this case, the
machine will shut down on an “empty” tank condition.
NOTE: If the machine operation is controlled by the lockout status of pretreatment,
but not controlled by a storage tank level, then jumper wires must be installed
between terminals 17 and 18 and between terminals 40 and 41. The machine
must be in AUTO mode to recognize the pretreatment signal or tank level
signals.
CAUTION: In all cases “dry” contacts must be used. This eliminates the possibility of
voltages from any other source feeding into the ECM-100 terminals.
6.2 pH Controller/Sensor (ECM-100-pH)
A factory installed pH sensor can be connected to your ECM-100. A high/low pH alarm is
included with the pH sensor and should be set at pH 6.5/3/0, respectively (unless special
instructions or conditions indicate otherwise) to protect against excess or loss of buffer
feed. If the high pH alarm deactivates the machine, the buffer tank and buffer pump must be
checked to ensure that buffer is being fed properly, and that the pump is primed. The system
is restarted by pressing OFF and then ON on the ECM-100. This will energize the chemical
pump so it can be properly adjusted. The system will stop again according to the alarm timer
if the pH remains in the high or low alarm range. When wired for acid pump control, the
ECM-100 will turn on the acid pump at 0.8 pH units less than the high pH alarm limit will
turn off the acid pump at 1.8 pH units less than the high pH alarm limit whenever the RO
pump is running (except during CIP mode).
54
Initial calibration of pH sensors is done at the factory. Accuracy should be rechecked at start-
up and at least monthly when in service, with a test kit or laboratory pH meter. Permeate
pH must not be used for calibration of the ECM-100 pH reading or adjustment of the
chemical pump. To calibrate the pH reading, refer to the calibration procedure included in
Section 8.0.
The pH probe may have to be cleaned or replaced some time after 6 to 24 months of
operation, depending on the type of use. Refer to the Spare Parts List (Section 11.0) for
specific Osmonics part numbers. Clean by soaking the glass electrode for10 minutes in a
2 pH acid (the type used for buffer).
NOTE: 23G machines built after September 1997 contain Version 2 (V2) circuit
board. This new circuit board includes the extra electronic components
built into the circuit board. When ordering replacement pH kits identify
whether you have Version 1 (machines built prior to September 1997) or
Version 2 (machines built after September 1997).
6.3 Remote Alarm Interface
6.3.1 Single Channel
A separate power supply can be mounted within the interior of the ECM-100 box
to power a single channel remote alarm box. The 2-wire cable from the remote
alarm box should be inserted through a gasket cord grip on the side wall of the
ECM-100 enclosure and connected to the + and - terminals on the power supply.
6.3.2 Six Channel
The six channel remote is mounted outside the ECM-100 enclosure to power a six
channel remote alarm system. Wires from the alarm should be routed through a
gasket cord grip on the side wall of the ECM-100 enclosure. Connect the positive
and negative wires to the proper power supply terminals.
6.4 Printer/Computer Interface
The ECM-100 is designed to allow data downloads to a computer or a printer. The basic
process of downloading the information to a printer or computer is the same. Data can be
downloaded as individual lines of information (Current display), or large groups of
information (Historical log). If a computer or printer is left connected to the ECM-100 for
long periods of time, the ECM-100 will display and download (echo) each successive set of
operational data as it is stored in the historical log table(s). The user can define the frequency
of operational data storage by accessing the Timer Presets Log Period (Menu 02) on the
ECM-100.
6.4.1 Printer Interface
The ECM-100 includes a 9-pin female serial communication port which will allow
you to interface with a printer. Two print functions are provided: Current display
and History Log. See Section 6.6.6 for Print Functions.
6.4.2 Computer Interface
The serial cable on the ECM-100 is wired at the factory to connect directly to a
personal computer, requiring only a standard 9-pin serial extension cable of
appropriate length and software.
The RS-232 communication configuration is:
Baud Rate 1200, 2400, 4800, or 9600, (user must specify)
Data Length 8 bits
Parity None
Handshaking Xon/Xoff
55
6.4.3 Computer Connection
Software Requirements
Requires serial communications software on your computer, such as:
HyperTerminal® (included with Windows 95, 98, NT, ME, 2000, or XP)
MicrosoftTerminal® (available separately for Windows 3.1)
Crosstalk® and Procomm® (versions available separately for almost any computer)
- or any of a number of similar commercial products.
To capture data from ECM-100 to a PC using HyperTerminal:
1. Go to HyperTerminal program on PC.
2. Go to “Capture Text”; the “Capture To” file is displayed in a dialog box; select it.
3. Then on the ECM-100 press ARROW keys to Log Tables Menu (05).
4. Press ENTER to enter Menu, use DOWN ARROW to move back through
History Log to desired point
5. Enter passcode. Refer to Section 4.2.6:
A “p” will be displayed next to the words “historical values” while the data is being
transferred to the PC.
6. After the transfer is complete, go back into HyperTerminal.
7. Go to “Capture Text” and select “Stop”.
8. Minimize HyperTerminal.
9. Insert floppy disk in the “A” drive.
10. Copy the file information to disk using “my computer” from the capture file:
C:programfiles/accessories/hyperterminal/capture
11. Open the file in Excel and allow the wizards to create the proper format
12. Save the information in its Excel format as well as original format to “H” drive.
56
13. Print hard copy of Excel file and place it in the Purified Water daily logbook. B
Membrane Delta-P listed on the right side of data files. See Table 6.11.
57
Table 6.10 Example ECM-100 History Log
DATE TIME PRESSURES FLOWS pH TEMP REJ Cp ALARM
PRE POS PRI FIN Pp Qc Qp
12/10/98 15:41 41 40 260 192 56 02.2 06.8 7.6 77 96.8 04 00
12/10/98 14:41 41 39 258 192 53 02.2 06.8 7.6 75 97.4 04 00
12/10/98 13:41 40 39 258 190 54 02.2 06.7 7.5 77 97.1 04 00
12/10/98 12:41 37 35 256 188 50 02.2 06.1 7.5 71 96.2 05 00
12/10/98 11:41 41 39 260 190 56 02.2 06.7 7.5 77 96.9 04 00
12/10/98 10:41 38 37 258 190 51 02.3 06.2 7.4 71 95.4 05 00
12/08/98 20:26 42 40 260 192 58 02.1 07.1 7.5 73 96.5 04 00
12/08/98 18:26 41 40 260 192 56 02.2 06.8 7.4 78 97.3 04 40
12/08/98 15:23 05 03 132 098 39 01.5 02.8 N/A 77 97.4 04 05
12/08/98 09:44 41 39 260 190 56 02.2 06.8 N/A 78 97.5 04 00
12/08/98 07:44 40 38 258 190 55 02.2 07.1 N/A 77 97.2 04 00
12/08/98 05:44 41 39 258 190 55 02.3 06.7 N/A 77 97.6 04 00
12/08/98 03:44 42 40 260 192 56 02.3 06.5 N/A 75 96.8 04 00
12/08/98 01:41 41 39 258 190 53 02.3 06.6 N/A 75 97.3 04 00
12/07/98 23:41 41 39 258 190 54 02.3 06.6 N/A 75 96.6 04 00
12/07/98 21:41 41 39 260 190 54 02.2 06.7 N/A 75 96.7 04 00
12/07/98 19:41 41 39 260 192 55 02.2 06.8 N/A 77 96.4 05 00
12/07/98 17:12 40 38 258 190 83 02.3 01.4 N/A 73 95.8 06 08
12/07/98 15:12 42 40 258 190 57 02.4 07.1 N/A 80 96.3 04 00
12/07/98 13:12 41 39 258 190 55 02.2 07.1 N/A 78 96.4 04 00
12/07/98 11:12 42 40 258 190 56 02.3 06.8 N/A 78 97.1 04 00
12/07/98 09:12 41 39 258 190 54 02.3 06.8 N/A 77 97.4 04 00
A printout of the ECM-100 History Log provides valuable information about the 23G. From
the example above (Table 6.10):
• Permeate Pressure High Alarm at 17:12 on 12/07/98.
• Inlet Pressure Low Alarm at 15:23 on 12/08/98.
• The operator ran the machine in the HAND mode for a short time on
12/08/98, and enabled the pH probe.
• On 12/10/98, before 1:40 am, the operator changed the Log Period Timer
Setting from 2 hours to 1 hour.
Hardware Requirements
All new IBM personal computers and clones are supplied with a standard 9-pin
male serial port, which uses the standard 9-pin extender cable.
If your computer has only one serial port connection being used by your mouse,
you will have to either add a second serial port for connecting to the ECM-100, or
unplug the mouse and connect the cable going to the ECM-100 and operate your
computer from the keyboard. This may require rebooting.
58
CAUTION: Nearly all computers have a 25-pin male connector, which is a
parallel printer port. Do not connect the ECM-100, modem or any
other serial device to this port.
If your computer has a 25-pin female connector (most likely a serial port), then you
will need to use either a 9-pin (M) to 25-pin (M) adapter connector with a standard
9-pin extender cable, or a 9-pin (M) extender cable instead. A M-M (male-to-male)
or F-F (female-to-female) gender adapter may be needed if the available extender
cable has the wrong port connection.
All of these parts are commercially available at computer and office supply stores.
6.4.4 Printer Connections
Connecting to a Serial Printer
Nearly all serial printers have a 25-pin female connector, so you will need a 9-pin
(M) to 25-pin (M) cable, or 9 x 25 adapter to use with the standard 9-pin extender
cable, and a “Null Modem” adapter or cable type. In some cases a gender adapter
may be needed with a standard IBM serial printer cable or if your only available
cable has the wrong style end. These components are commercially available at
computer and office supply stores. The green and red wires at terminals #45 and
#47 can be switched to provide the same cross-cross effect as a “Null-Modem.”
Printer settings (refer tot he documentation provided with your printer):
Baud Rate 1200, 2400, 4800, 9600 (user must specify)
Parity None
Data Bits 8
Handshake Xon/Xoff
Go to Section 6.9 and complete Print Test.
Connecting to a Parallel Printer
Requires a “Serial-to-Parallel” (S-P) converter box between the ECM-100 cable and
the cable to the printer (which typically uses a 36-pin Centronix connector).
NOTE: If a serial printer is not available, a S-P converter box is commercially
available at computer and office supply stores.
Use a standard (Centronix style) printer cable from the printer to the “Parallel”
port on the S-P converter. Connect the ECM-100 to the serial port on the S-P in
the same manner for connecting to a serial printer (described in the previous
section).
Converter settings (refer to the documentation provided with our converter):
Baud Rate 1200, 2400, 4800, or 9600, (user must specify)
Parity None
Data Bits 8
Handshake Xon/Xoff
Direction Serial-to-parallel (S-P)
6.4.5 Print Test
The print test below prints the current displays on the ECM-100.
1. On the ECM-100 keypad, press the ARROW keys to scroll to the “Maintenance
Menu” (07).
2. Press ENTER select the “Maintenance Menu.”
3. Press the ARROW keys to scroll to “Print Current Values.”
59
4. Press the ENTER key.
Pressing the ENTER key caused the ECM-100 to output two lines of text and
numbers to the printer representing the readings currently being displayed on the
LCD screen.
Figure 4.6 indicates where the wires for the ECM-100 communication cable are
placed on the main board terminal strip, should they become disconnected or
require replacement.
6.4.6 Print Functions
Printing Current Displays
1. Connect printer to ECM-100 as described in Printer Connections.
2. Print current displays as described in Print Test.
Printing History Logs
1. Connect printer to ECM-100 as described in Printer Connections.
2. Perform print test as described in Print Test.
3. On the ECM-100 keypad, press the ARROW keys to scroll to the “Log Tables
Menu” (05).
4. Press ENTER select the “Log Tables Menu.”
5. Enter passcode to download historical data. Refer to Section 4.2.6.
All historical data will be sent to the printer and printed in chronological order.
60
7.0 TROUBLESHOOTING
This troubleshooting guide can assist you in identifying common operating problems you may
experience with your machine. Many of these problems can be easily corrected by the operator;
however, for those that persist or are not understood, you should contact your equipment supplier.
Have the following information available when calling your equipment supplier:
1. Machine installation date
2. Model number (found on right-hand side of front panel)
3. Serial number (found on right-hand side of front panel)
4. Daily Log Sheets
5. Description of problem
6. Software version from software module.
61
Troubleshooting Guide - Machine Performance
Symptom Possible Causes Remedies
High operating pressure Inaccurate pressure Install a temporary manual gauge to compare
(continued) indication. readings, and check sensor and cable as desired
for “Low Operating Pressure.” Replace or
calibrate as required.
62
Troubleshooting Guide - Machine Performance
Symptom Possible Causes Remedies
Low permeate flow rate Cable or turbine element Repair or replace the cable or turbine.
(0 gpm to 20% less than damaged.
desired) Sensor cable not fully inserted Insert the cable so it snaps into place.
(continued) into flow turbine element
housing.
Flow indicator inaccurate Check the flow rate manually with a stopwatch
(possibly due to fouled and calibrated container. If reading is off from
turbine in sensor). ECM-100 display by >10%, check for a fouled
turbine and clean or replace as required. Check
settings in Calibration Menu (06).
ECM-100 flow reading Pressing the ESC button usually clears the lockup.
“lockup”. Power down for 2 minutes, check Alarm Limits
and Calibration Menu settings, recall Factory
Settings.
Low concentrate flow Dirty or fouled membrane Flush, clean, and sanitize the membrane elements.
rate, normal or higher elements.
than normal operating Concentrate valve or Remove the concentrate valve stem and/or
pressure (0 gpm to 20% concentrate orifice pressure disassemble the plumbing to the orifice. Clean the
less than desired) not properly adjusted. orifice as required.
Concentrate outlet line Examine the concentrate line for obstructions or
restricted. kinks, and repair or replace the tubing.
Faulty flow turbine or cable Switch sensor cable between concentrate and
(all pressures normal). permeate flow turbines to isolate the problem to
cable or turbine.
Cable or turbine element Repair or replace the cable or turbine.
visibly damaged.
Sensor cable not fully inserted Insert the cable so it snaps into place.
into flow turbine element
housing.
Flow indicator inaccurate Check the flow rate manually with a stopwatch
(possibly due to fouled and calibrated container. If the reading is off from
turbine in sensor). the ECM-100 display by >10%, check for a fouled
turbine and clean or replace as required. Check
setting in Calibration Menu (06).
ECM “lockup” (software Pressing the ESC button should clear the lockup.
version E6.9 or greater). Power down for two minutes, check Alarm Limits
and Calibration Menu settings, and recall Factory
Settings.
63
Troubleshooting Guide - Machine Performance
Symptom Possible Causes Remedies
Low rejection and high Membrane elements dirty or Flush, clean, and sanitize the membrane elements.
permeate flow fouled.
(hydrolyzed membranes) O-ring seal broken or Check the sealing surfaces on the
damaged. O-ring groove, interconnectors, and end caps.
Replace damaged parts.
Recovery too high. Adjust concentrate/recycle orifices.
Membrane elements oxidized Verify proper operation of pretreatment (chlorine
due to chlorine break removal/carbon filtration). Damage is irreversible,
through. replace membranes.
New membrane elements Operate machine for a minimum of
oxidized due to cleaning and 8 hours to remove biocide and stabilize permeate.
sanitizing prior to completion Refer to Membrane Element Installation (Section
of 8 hour flush to drain 5.13.2).
procedure.
Membrane element life Replace membrane elements (clean and evaluate
expired. before replacing).
Concentrate membrane Reverse position or replace seal.
element seal backward or
damaged.
Excessive permeate back Check permeate outlet valves or inlet valves.
pressure.
Concentrate flow too high. Check to see if machine is in auto flush.
Low rejection Inlet diaphragm valve not Clean or replace the inlet solenoid valve. Make
closing when machine is sure the inlet diaphragm valve stops the water
turned off. flow when shut off.
Declining rejection (or Dirty or fouled membrane Flush, clean, and sanitize the membrane elements.
high permeate elements.
conductivity) Change in incoming feedwater Open the concentrate valve and flush. Test the
quality. water for pH, hardness, TDS, and iron content. A
water analysis should be sent to your equipment
supplier for review.
Conductivity or rejection Calibrate the sensors with the standard solution
reading(s) inaccurate or or check the readings with another conductivity
sensor(s) fouled. meter. Check the connections between the sensor
and ECM-100 board. Check the permeate
conductivity calibration. If the rejection reading is
still not matching your calibration with a hand-
held instrument sampling feed and permeate, then
check the feed conductivity calibration. The
readings are most precise at a temperature of
77° F (25° C). Clean and/or replace the sensors.
64
Troubleshooting Guide - Machine Performance
Symptom Possible Causes Remedies
Declining rejection (or O-ring seal broken or Check the sealing surfaces on the O-ring groove,
high permeate damaged. interconnectors, and end caps. Replace damaged
conductivity) parts.
(continued) Damaged membrane Replace membrane elements.
elements.
Overfeeding buffer solution Check the pH of the concentrate and adjust to
due to improper adjustment 6.0. Check the inlet pressure to be sure siphoning
of pump or low inlet pressure. of the buffer solution is not occurring. Check pH
probe calibration.
65
Troubleshooting Guide - ECM-100 Display Failures
Symptom Possible Causes Remedies
Temperature in ECM-100 Temperature circuit failure. Refer to ECM-100 Troubleshooting
cannot be adjusted (Section 4.7).
Water leaking from O-ring or diaphragm failure. Replace valve.
permeate and/or Contact your equipment supplier for
diaphragm valves assistance.
Check fitting.
Tank level control feature Faulty float/tank level control. Replace float/tank level control.
does not work Input wires not properly Refer to Section 6.1 and Figure 4.6.
connected.
Incompatible level controller.
Water flowing when Inlet solenoid valve or Clean or replace the valve(s). Clean
machine is turned off diaphragm valve not closing or and sanitize the membranes
seating properly. immediately. Water must not pass
Solenoid and diaphragm valve through inlet when the machine is off.
tubed incorrectly.
ECM-100 display screen Power line disturbance. Install a surge protector and AC line
backlighting flickers emi/rfi filter device between the ECM
(Note: a slight flicker is power cord and the power source.
normal) Note: Some minor flickering is
normal. Check for loose fuse on relay
board, loose wiring connection and
ribbon cable between boards.
LCD screen blank or Power line interruption or Pressing the ESC button should clear
contains garbled text electrical noise. screen, power down for 2 minutes and
restart.
Most or all lights are off Blown fuse or loose ribbon Check fuses, check and reseat the
cable between Main and Relay ribbon cable. Check for loose fuse
Boards. holder.
Bad Relay/Main Board. Contact your equipment supplier for
assistance.
Lost 110/220 VAC power to Contact your equipment supplier for
the ECM-100. assistance.
Power surge possibly due to Replace damaged parts and install a
lightening strike or voltage surge protector. Contact your
surge. equipment supplier for assistance.
66
TROUBLESHOOTING GUIDE - 23G System Failures
Symptom Possible Causes Remedies
23G electrical machine ECM-100 “lockup” (usually Power down for 2 minutes, then
shutdown due to power fluctuation). restart. Check alarms, timers, and
calibration settings. Recall Factory
Settings.
Thermal overload relay Turn the machine of, reset the relay,
tripped check the motor amp draw and line
voltage, Adjust the overload relay
based on the motor amp draw if
required. Check for excessive
pressure or flows.
Machine will not turn on Alarm condition has turned Check the ECM-100 display for Alarm
off machine. identification. Remedy the alarm. The
ECM-100 will remain in a state of
alarm until the OFF key is pressed.
Thermal overload in motor Check amp draw of the motor and
starter. reset thermal overload.
Motor and/or pump not See pump instructions. Contact your
operating properly. equipment supplier for possible repair
or replacement.
Fluid temperature over 105° F Check the feedwater supply
(41° C). temperature. Maximum operating
temperature is 95° F (35° C).
No power to machine. Check the fuses or circuit breakers,
measure the voltage.
23G machine blowing Faulty wiring to pretreatment Remove wires at 17, 38, 40, and 42 to
fuses or tank level switches. isolate problem. Repair as needed.
Shorted flow sensor. Flow pickup sensor hot to the touch.
Replace and calibrate sensor.
Shorted pressure transducer Contact your equipment supplier for
or faulty cable. assistance.
Fault on Main Board. Contact your equipment supplier for
assistance.
One or more of the Faulty solenoid or wiring, or Observe the lights on the ECM-100
motors or solenoid valve faulty Relay or Main board. front panel, check timer, and alarm
is not being energized settings. Check for AC power out of
the appropriate terminal on the Relay
Board.
Loose connection at the Relay Check all connections.
Board.
67
7.1 Emergency Alarm Bypass
CAUTION: The following are regarded as emergency conditions. Bypass of the alarm
will defeat the automatic safety protection features of the ECM-100. Bypass
of these measures may cause damage to the machine or be severely
detrimental to product water quality if the condition being monitored goes
into an actual error state while the sensor is being bypassed. Depending on
which sensor is being bypassed, the machine operation will need to be
monitored closely until the problem is repaired (while replacement parts
are in transit). In many cases, the machine can be run for short periods in
emergency situations by simply turning it on in the Manual or CIP mode.
The machine should never be left unattended in the Manual or CIP mode.
WARNING: When the machine is operating in the CIP mode, all alarms
except HIGH TEMP, HIGH PRIMARY, AND HIGH PERMEATE,
are ignored. OPERATION OF THE 23G MACHINE WHILE THE
ALARM SYSTEM IS BYPASSED COULD POSE A RISK OF
SERIOUS INJURY OR DEATH TO HEMODIALYSIS PATIENTS.
CAUTION: The procedures listed below are temporary. Prolonged operation as
described below will damage the machine. These procedures should only
be used to allow production of product water until repairs can be
completed. The machine should be continuously monitored while operating
in this mode.
WARNING: Disconnect power from RO when working in any of the control boxes or
serious injury may occur.
7.1.1 Permeate Conductivity High or Rejection Low Alarms
Use a hand-held conductivity test meter to ensure that the water quality is
acceptable. Disconnect the white wire from terminal 27 on the Main Board and
terminal strip (the reading will go to 1 µS). Recheck conductivity until the problem
is repaired.
If this remedy does not work contact your equipment supplier.
7.1.2 Rejection Low Alarm Due to Failed Feed Conductivity Probe
Install a short piece of wire between terminals 24 and 25 on the Main Board
terminal strip (forces reading to 2550 µS).
If this remedy does not work contact your equipment supplier.
7.1.3 Temperature High Alarm
Switch wires to use the temperature element which is encapsulated in the
Permeate Conductivity probe. Remove the red and green wires from terminals 23
and 24, and connect the red and green wires from the permeate conductivity
probe cable to terminals 23 and 24.
If this remedy does not work contact your equipment supplier.
7.1.4 pH Alarms
Disable the pH function by entering zero (0) in the Calibration Menu (06). Then
move the wire connecting terminal 8 to terminal 11 on the Relay Board and adjust
the chemical feed pump carefully for a slow continuous feed. Test the pH frequently
(hand-held pH meter or test kit) and readjust the pump accordingly.
If this remedy does not work contact your equipment supplier.
68
7.1.5 Pressure
• First check the wiring connections, and clean any corrosion from the connector
on the back of the transducer.
• A slowly drifting pressure reading over a period of several days can be
temporarily corrected by adjusting the offset setting in the Calibration Menu
(restore to original values for calibration of new sensors).
• Adjusting the offset value adjusts the entire operating range of the sensor.
• To bypass a pressure sensor or cable, power down and remove the cable from
the Main Board terminal strip (see Figure 4.6).
• Add a short length of wire from the terminal where the white wire was just
removed, and connect it to a neighboring pressure terminal containing a white
sensor wire.
• Add a second length of wire from the terminal where the green wire was
removed, and connect it to the neighboring pressure terminal containing a green
wire (connect Primary to Final, Permeate to Pre- or Post-Filter).
• Power up and set the pressure offset in the Calibration Menu (06) to obtain a
nearly normal reading for the pressure being bypassed.
• Restore the offset settings and wiring when the new transducer is installed.
• The new transducer must be calibrated (see Section 8.2).
• Remove transducer and clean port.
If this remedy does not work contact your equipment supplier.
7.1.6 Permeate Flow (Stuck at Zero)
• Check flow turbine to ensure it spins freely.
• First check connections (Figure 4.6), power down for 2 minutes, recall Factory
Settings and check the values in the Calibration Menu (06).
• Switch sensor cables, or insert the permeate cable into the concentrate turbine
(the machine will run normally with a concentrate flow reading of zero.
• Unplug the cable from its turbine, and set the flow offset in the Calibration Menu
to 99 (forces the flow reading to 0.1), then set the permeate low flow alarm to
0.0.
• Return to the proper settings after the problem is corrected.
• Remove turbine and blow through it to be sure it spins freely.
If this remedy does not work contact your equipment supplier.
69
7.2 General ECM-100 Reference/Troubleshooting Guidelines
70
7.2.2 If sporadic, unexplained alarms occur, check the Main ECM-100 Board Terminal
Strip on back door for good connections.
CAUTION: This procedure should be performed by qualified electrical service
personnel only.
1. Turn the machine OFF.
2. Disconnect the power to the ECM-100 (for single-phase machines, also
disconnect power to the motor controls).
3. Visually inspect for signs of damaged components.
4. Gently tug on each wire on the main board terminal strip to test for good
electrical contact.
5. Contact your equipment supplier for assistance in repairing any loose or broken
wires.
6. Ensure the terminal board is firmly connected to the main board by gently
pressing on the top of the strip, pushing it toward the main board.
CAUTION: Do not apply too much pressure - you may damage the board.
7. Reconnect power and test for proper operation.
For additional assistance contact your equipment supplier.
7.2.3 If sporadic, unexplained alarms occur, check the Relay Board Terminal Strip for
good connections (Relay Board).
WARNING: ELECTRICAL SHOCK HAZARD - SERVICE TO BE
PERFORMED BY QUALIFIED ELECTRICAL
PERSONNEL ONLY!
1. Turn the machine OFF.
2. Disconnect the power to the ECM-100 (for single-phase machines, also
disconnect power to the motor controls).
3. Closely inspect each wire connection to see that none are broken, frayed, or
loose in their screw terminal and that all crimp terminal ends are squeezed
tightly on the wire and firmly screwed to the terminal block.
4. Ensure that all terminal block screws and jumper links are securely fastened.
5. Check for blown fuses, and squeeze the fuse holder clips together slightly to
hold the fuses securely.
For additional assistance contact your equipment supplier.
7.2.4 Low Rejection Warning (Due to High Purity Feed Water)
The ECM-100 may exhibit a low rejection warning condition when the factory
default low rejection alarm setpoint of 88% is used with high purity feed water. The
permeate conductivity may be acceptable, but the percent (%) rejection may read
low enough to cause an alarm.
The ECM-100 calculates % rejection using the following equation:
Permeate Conductivity
% Rejection = 1- x 100
Feed Conductivity
Since the % rejection is based on a ratio between the feed conductivity and the
permeate conductivity, higher quality feed water may result in a low % rejection
alarm. Higher recovery will typically lower the permeate rejection using the ECM-
100 calculations.
71
If a low % rejection alarm results from high purity feed water when the permeate
conductivity is at acceptable levels, the following three methods could be used:
1. Reduce low % rejection alarm setpoint.
2. Adjust the feed conductivity calibration potentiometer for a slightly higher feed
conductivity reading. See Section 8.0 for calibration of feed conductivity.
NOTE: Adjusting feed conductivity to a slightly higher reading will result in an
inaccurate feed conductivity displayed on the ECM-100.
3. Use a resistor in place of the feed sensor. Remove the feed conductivity input
and replace with a resistor to simulate a feed conductivity. A 10 K ohm resistor
would indicate 250 µS.
NOTE: To properly monitor permeate conductivity make sure the PERM HI
COND ALARM Menu in the Maintenance Menu (07) is properly set.
See Section 4.6.10 for accessing Permeate High Conductivity Alarm
Menu.
For additional assistance contact your equipment supplier.
7.2.5 Verifying the Temperature Circuitry of the Main Board
1. Turn the machine OFF.
2. Unplug the power cord for the ECM-100.
3. Disconnect the temperature sensor wires from terminal posts 23 and 24.
4. Cover the temperature sensor wires which were removed from terminal posts
23 and 24 with electrical tape. Secure these wires in a location that prevents
contact with the main circuit board.
5. Install a 3 K ohm resistor between terminal posts 23 an 24.
6. Connect the power cord for the ECM-100.
7. Adjust potentiometer marked “temp” (V2) until the temperature reads 77° F
(25° C).
NOTE: If the temperature cannot be adjusted then the main board may need to
be replaced. Contact your equipment supplier.
8. Unplug the power cord and remove the 3 K ohm resistor, and install the
temperature sensor wires.
9. If the above steps do not correct the problem, replace the feed conductivity
probe.
NOTE: When installing a new feed conductivity probe, unplug the power cord,
make all connections, and then plug the power cord in.
NOTE: The temperature sensor can be temporarily bypassed while waiting for
replacement parts by installing a 3 K ohm resistor between terminals
23 and 24.
7.2.6 Difficulty Calibrating Permeate Conductivity
The integrity of the permeate conductivity circuitry on the main logic board can be
verified by connecting a fixed resistor in place of the conductivity probe.
1. Turn the machine OFF.
2. Unplug the power cord for the ECM-100.
3. Disconnect the permeate conductivity wires from terminal posts 27 and 28.
72
4. Install a 5 or 10 K ohm resistor between terminal posts 27 and 28.
5. The resulting conductivity should be displayed on the ECM-100.
• 10 K ohm should give a reading of 10 µS.
• 5 K ohm should give a reading of 20 µS.
6. If the ECM-100 does not display the correct permeate conductivity then the
main board may need to be replaced. Contact your equipment supplier.
Refer to Troubleshooting Guide (Section 7.0) for additional information.
7.2.7 Information to Obtain Before Contacting Your Equipment Supplier
1. Machine installation date.
2. Model number (found on right-hand side of front panel).
3. Serial number (found on right-hand side of front panel).
4. Daily Log Sheets.
5. Detailed description of problem.
6. Software version from software module.
73
8.0 23G SOFTWARE
8.1 Calibration Procedures
NOTE: If the software for your main logic board is labeled G2.1 or higher, you have a
Version 2 (V2) main logic board.
V1 and V2 main logic boards and relay boards are interchangeable (i.e., you could
have a V1 main logic board and a V2 relay board and vice versa).
23G machines built after 1997 contain Version 2 (V2) circuit boards. This new
circuit board includes extra electronic components built into the circuit board.
When ordering replacement parts identify whether you have V1 (machines built
prior to 1997) or V2 (machines built after 1997). Contact your equipment supplier
with questions.
Normally, the only sensor requiring periodic calibration is the pH probe, which
should be checked semi-annually.
8.2 pH Calibration Procedure - Software Version V2
1. Obtain two standard pH reference solutions with different pH values. Solutions of pH 4.0
and 7.0 or of pH 4.0 and 10.0 are recommended.
2. Remove the pH sensor from the incoming waterline, and rinse in tap water.
3. From the calibration menu, use the ENTER key to scroll to the pH cal low menu item.
Before changing the pH calibration value, place the wetted end of the pH sensor in the
standard solution with the lower pH. Swirl it a little and leave it dipped - with at least
1 inch of the sensor length submerged (so that the metal body of the probe is in contact
with the solution by approximately 1/4-inch).
4. On the ECM-100, enter passcode 1. Using the ARROW keys, change the pH cal low
setting to be 10 times that of the pH of the solutions. For example, 40 for 4.0 solution.
The number indicates tenths of a pH unit. Press the ENTER Key to store the calibration
value and go on to the high pH limit.
5. The next setting in the calibration menu is pH cal high. Before dipping the pH sensor in
the high pH solution, rinse the pH sensor with pH neutral water. The pH sensor may
also be rinsed with some of the high pH solution. Place the sensor in the standard
solution of higher pH. Swirl it a little bit and leave it dipped - with at least 1 inch of the
sensor length submerged.
6. On the ECM-100, enter passcode 1 again. Using the ARROW keys, change the pH cal
low setting to be 10 times that of the pH of the solution. For example 70 or 7.0 solution
or 100 for 10.0 solution. Again, the number indicates tenths of a pH unit. Press the
ENTER key to save the new reading.
7. Calibration is now complete. To check it, rinse the probe with tap water and dip it into
the low pH solution again to see if it reads accurately. Repeat the calibration if necessary.
8. Rinse or blot away any remaining droplets of the pH solution and reinstall the pH sensor
into the incoming waterline.
9. Generally this 2-point pH calibration procedure should be repeated on a bi-monthly
basis. Some situations will require more frequent recalibration while others will require
less.
10. If the probe does not seem to be responding, try soaking it in a 2.0 pH acid for 10
minutes. Repeat the calibration.
11. If the probe will not calibrate after 2 or 3 attempts, refer to the pH section in the
Troubleshooting Guide (Section 7.0).
74
12. Save the settings using passcode 2 in the maintenance menu Factory Settings.
8.3 Logic Board
NOTE: For machines equipped with Rev G2.2 software as shipped (V2 Logic Board).
These documented specifications are subject to change, depending on the unique
characteristics of each machine during quality assurance (QA) testing.
Any “user” variation of these specifications (including any software upgrades) in the
field (after the machine has left Osmonics shipping dock) are solely the
responsibility of the user to document and control.
Menu #2
Alarms ECM Adjustment Range Alarm Limit
PERM COND HI 0-200 µS/cmab 30 µS/cm
c
TEMP HI 0-225° F (0-123° C) 105° F (41° C)
pH HIc 0.0-14 pH unitsd 9.0 pH units
c
pH LOW 0.0-14 pH units 3.5 pH units
POST-FILTER PRESS LOWc 0-99 psi (0-68 [barX10]) 12 psig (8 [barX10])
e
PRIMARY PRESS HI 0-510 psi (0-352 [barX10]) 280 psig (193[barX10])
PRIMARY PRESS LOWc 0-510 psi 90-352 [barX10]) 150 psig (103 [barX10])
e
PERM PRESS HI 0-99 psi (0-68 [barX10]) 80psig (55[barX10])
REJECTION LOW 0-99% 88%
f
FILTER PRESS DROP HI 0-99 psi (0-68 [barX10]) 14
MEMBRN PRESS DROP HI 0-510 psi (0-352 [barX10])g 108
h
PERM FLOW LOW 0.0-20.1 gpm (0.0-6.5L) 2.6
a. Adjustment range of “Permeate Conductivity High” alarm is 0-50 µS/cm for Rev D3 software; 0-200 µS/cm
for Rev E0 or higher software.
b. Below 200 µS/cm, there are 2.5 units of specific conductance (µS/cm) per unit of Total Dissolved Solids
(ppm or mg/L as CaCO3).
c. Shutdown alarms with adjustable delay (1-99 sec).
d. If an acid injection pump is installed, the high pH alarm determines when the chemical pump turns on. After the
chemical pump lowers the pH to 1.8 units below the alarm setting, the pump will be turned off.
e. Shutdown within one second (non-adjustable).
f. Set alarm limit at 8 psi (6[barX10]) greater than drop observed during data collection fro QA test form.
g. Set alarm limit at 1.5X the drop observed during data collection for QA test form.
h. Set alarm limit at 60% of flow observed during data collection for QA test form.
75
Menu #3
Timers ECM Adjustment Range Alarm Limit
a
RO PUMP DELAY 1-99 sec 6 sec
b
START-UP PERM DIVERT 0-99 min (select 0 or 2 min) 2 min
AUF PERIOD 0-99 hr 1 hr
AUF DURATION 0-99 min 6 min
ALARM SHUTDOWN DELAY 0-99 sec 15 sec
LOG PERIOD 0-99 hr 1hr
c
AUTO-ON PERIOD 0-99hr 0 hr
c
AUTO-ON DURATION 0-99 min 0 min
a. An RO pump delay of 0 will disable the RO pump.
b. Select zero (0), if permeate divert option is not installed. Select 2 min, if it is installed.
c. When enabled, typical settings are auto-on period of 4 hours, and auto-on duration of 15 minutes.
Menu #6
76
8.4 Temperature Calibration Procedure
8.4.1 Cleaning the Feed Conductivity Sensor
1. Turn machine OFF.
2. Locate and remove the feed conductivity sensor
The temperature sensor is encapsulated in the feed conductivity sensor. The feed
conductivity sensor is located downstream of the pre-filters and above the inlet
diaphragm valve. A bucket or container may be needed to catch the water when
the feed conductivity sensor is removed.
3. Clean any debris or residue from the probe tips with a clean towel.
If either one of the tips is broken off, the probe must be replaced.
4. Install the feed conductivity sensor back in the machine.
8.4.2 Calibrating the Temperature
NOTE: Machine should be running while calibrating temperature.
1. Take a sample of the feedwater [about 8 ounces (0.24 L)] from the feed sample
port on the inlet of the machine. Measure the temperature with a recently
calibrated thermometer.
2. Locate potentiometer marked “temp” on the main circuit board.
The circuit board for the potentiometers is located in the door of the ECM-100
enclosure.
The potentiometer marked "temp" is located just below the center of the board.
3. Adjust the potentiometer marked "temp" until the temperature on the ECM-
100 display matches the temperature of the hand-held thermometer.
• Clockwise (CW) rotation lowers the temperature reading.
• Counterclockwise (CCW) rotation raises the temperature reading.
4. If the temperature reading on the ECM-100 will not adjust see Troubleshooting
(Section 7.0).
8.5 Conductivity Calibration Procedure
8.5.1 Measuring the Conductivity of Feed and Permeate Samples
NOTE: The 23G displays conductivity in microSiemens (µS).
NOTE: Use a hand-held, recently calibrated conductivity meter. The meter
should read in microSiems (µS).
NOTE: Some hand-held meters are not temperature compensated and,
therefore only accurate at 77° F (25° C).
1. Take a sample of the feedwater [about 8 ounces (0.24 L)] from the feed sample
port on the inlet of the machine. Measure the conductivity with a recently
calibrated conductivity meter.
2. Take a sample of the permeate [about 8 ounces (0.24 L)] from the permeate
sample port on the machine. Measure the conductivity with a recently calibrated
conductivity meter.
Be sure to rinse the conductivity meter thoroughly in a stream of water from the
feed sample valve before taking feed sample reading and permeate sample reading.
Follow the manufacturer’s instructions for calibrating with a conductivity meter.
77
8.5.2 Verifying the Percent Rejection Reading on the ECM-100
Calculate the ECM-100 percent rejection using the following equation:
Permeate Conductivity
% Rejection = 1- x 100
Feed Conductivity
78
6. Adjust the potentiometer marked “feed” until the ECM-100 feed conductivity
reading matches the conductivity as measured by the hand-held meter [at 77° F
(25° C) for some meters].
• Counterclockwise (CCW) increases the conductivity reading.
• Clockwise (CW) decreases the conductivity reading.
NOTE: The 23G displays conductivity in microSiemens (µS).
NOTE: If the feed conductivity cannot be calibrated with the potentiometer
marked “feed” the sensor may need to be replaced.
7. Shut off the machine, remove the feed conductivity probe and check to be sure
it is not fouled and the graphite tips are not broken.
8. Reinstall the feed conductivity probe.
8.5.5 Restoring the Rejection Low Alarm Setting
1. Press the UP ARROW to change the Rejection Low alarm back to its original
setting (the factory default for Rejection Low is 88%).
2. Press the ENTER key to save the new value.
3. Press ESC twice to exit back to the main screen.
8.5.6 Calibrating the Permeate Conductivity
If the ECM-100 permeate conductivity reading matches the hand-held meter
reading, then the permeate conductivity is calibrated (proceed to Section 8.10.6
Restoring the Rejection Low Alarm Setting).
If the permeate conductivity reading is 1.0 or less refer to ECM-100
Troubleshooting (Section 4.7).
1. Take a sample of the permeate from the permeate sample port [about 8 ounces
(0.24 L)] in order to establish the known conductivity.
2. Measure the permeate conductivity reading from the sample collected.
Be sure to rinse the conductivity meter thoroughly in a stream of water from the
permeate sample valve before taking the reading.
3. Locate the potentiometer marked “perm” on the main circuit board.
The main circuit board is in the door of the enclosure.
The potentiometer marked “perm” is in the center on the right-hand side of the
circuit board.
4. While the machine is running, adjust the potentiometer marked “perm” until
the ECM-100 permeate conductivity reading matches the conductivity as
measured by the hand-held meter [at 77° F (25° C) for some meters] while the
machine is running.
• Counterclockwise (CCW) increases the conductivity reading.
• Clockwise (CW) decreases the conductivity reading.
5. Saving to Factory Settings (Menu 11).
NOTE: Whenever a value is adjusted it must be saved in the Factory Settings
Menu (11).
• Press ESC twice to return to the ECM-100 default menu.
• Press the ARROW keys to scroll to the Maintenance Menu (07).
• Press ENTER to select the Maintenance Menu.
79
• In the Maintenance Menu, use the ARROW keys to scroll to the Factory Settings
Menu (11).
• Press ENTER to select Factory Settings.
Two lines of factory settings will be displayed.
• Enter the storage code using the following keys in sequence to save the settings:
a. HAND/AUTO
b. CIP
c. ON
d. ENTER
8.6 Pressure Transducer Calibration Procedure
1. De-energize the 23G pump and shut inlet valve to the 23G.
2. Energize the 23G controller.
3. Push the HAND/AUTO button to the HAND mode. Then push the controller ON
button, wait two seconds and push the CIP button. Observe the CIP button illuminate.
In several seconds you will hear the inlet solenoid valve open. The pump should not
start.
4. Open the feed, permeate, and concentrated sample valves. Let the machine drain several
minutes until the water is almost completely drained out.
5. Push the UP arrow to advance to the calibration menu, then push the ENTER button
until you reach pre-filter pressure.
6. Insert pass code to change value on the pre-filter pressure reading on the ECM-100
screen by pushing HAND/AUTO, then CIP, then the ALARM/BYPASS buttons.
7. Use the UP arrow on the controller to advance the pre-filter pressure reading on the
screen to 6. Wait 15 seconds for the controller to accept calibration information. Then
push the DOWN arrow slowly until it goes to the next lower number, waiting 15
seconds between number changes. Continue with this procedure until you reach zero.
Wait 15 seconds then push the ENTER button. This enters the calibration information
into the menu and also advances you to the post-filter pressure. Use the same procedure
for post-filter, primary, and final pressures. When you reach the permeate pressure, the
number that was changed to 6 is on the left of the word calibrate on the second line.
Calibrate the permeate pressure by using the same procedure used on the other
pressure transducers. When zero has been reached, wait 15 seconds and then push
ENTER several times until you are out of the menu. Close all sample valves.
Open the inlet valve. Turn machine on to allow water to flow through machine for 2 to
4 minutes to refill machine with water before starting.
Push the OFF button on the ECM-100 controller, then push the HAND/AUTO button
to AUTO position. The machine is now ready to start up. Check to make sure all
feedwater valves are open. Observe the presence of pre-filter water pressure on the
ECM-100 screen. Energize the 23G pump. Then push the START button on the ECM
controller. Observe the pressures as the machine starts up. With every thing running
well, the calibration of the five pressure transducers is completed.
NOTE: The machine is designed to run in AUTO mode. Prior to restarting the
machine, confirm that the machine is in AUTO mode.
8. Press the ON key to turn machine on.
9. If unable to calibrate the ECM-100 as described above, see ECM-100 Troubleshooting
(Section 7).
80
8.7 Flow Calibration Procedure
8.7.1 Measuring Permeate Flow Rate
1. Check and record the ECM-100 permeate flow while the machine is running.
2. Turn the machine OFF.
3. Install a 1-inch I.D. flexible hose [at least 4 feet (1.2 m) in length] to the CIP
permeate fitting. The CIP fitting requires a 1-inch MPT threaded fitting.
4. Open the permeate CIP valve.
5. Close the permeate outlet valve.
6. Secure the end of the hose attached to the CIP fitting.
7. Turn machine ON.
8. After 15 - 20 seconds of operation measure the permeate flow.
Measure the permeate flow with an accurate stopwatch. Record the time
needed to collect water in a container with a known volume. Use the formula
below to calculate volume:
# of gallons
gallons per minute (gpm) = x 60
# of seconds to fill container
Measure the concentrate flow with an accurate stopwatch. Record the time
needed to collect water in a container with a known volume. Use the formula
below to calculate volume:
# of gallons
gallons per minute (gpm) = x 60
# of seconds to fill container
81
If the two readings differ by more than 0.3 gpm (0.07 m3/h) adjust the
calibration settings as described in Section 8.7.3 to 8.7.5.
8.7.3 Calibrating the Concentrate and Permeate Flow Rate Offsets
NOTE: The machine should be running.
Calibrating Concentrate Flow Rate Offset
1. Press the ARROW keys to scroll to the Calibration Menu (06).
2. Press ENTER to select the Calibration Menu.
3. Press ENTER until the “Conc Flowrate Offset” is displayed.
4. The “Conc Flowrate Offset” should read 00. If it does not read 00:
• Enter the passcode in the following sequence to adjust the reading:
a. HAND/AUTO
b. CIP
c. ALARM BYPASS
• Press the ARROW keys to set the "Conc Flowrate Offset" to 00.
• Press ENTER to save the new value.
The Concentrate Flow Rate Offset is now calibrated.
Calibrating Permeate Flow Rate Offset
NOTE: It is not necessary to enter the passcode for additional adjustments in
the Calibration Menu.
1. Press ENTER until the “Perm Flowrate Offset” is displayed.
2. The “perm Flow Rate Offset” should read 00. If it does not read 00:
• Press the ARROW keys to set the “Perm Flowrate Offset” to 00.
• Press ENTER to save the new value.
The Permeate Flow Rate Offset is now calibrated.
8.7.4 Verifying the Concentrate and Permeate Flow Rate Slopes
Verifying the Concentrate Flow Rate Slope
NOTE: It is not necessary to enter the passcode for additional adjustments in
the Calibration Menu.
1. Press ENTER until the “Conc Flow Rate Slope” is displayed.
2. The “Conc Flow Rate Slope” should read 37. If it does not read 37:
• Press the ARROW keys to set the “perm Flow Rate Slope” to 37.
• Press ENTER to save the new value.
The above steps verify the factory default sets for the concentrate and permeate
flow rate slopes. The following procedure will calibrate the slopes.
Verifying the Permeate Flow Rate Slope
NOTE: It is not necessary to enter the passcode for additional adjustments in
the Calibration Menu.
1. Press ENTER until the “Permeate Flow Rate Slope” is displayed.
2. The “Perm Flow Rate Slope” should read 37. If it does not read 37:
a. Press the ARROW keys to set the “Perm Flow Rate Slope” to 37.
b. Press ENTER to save the new value.
c. The above steps verify the factory default sets for the concentrate and
permeate flow rate slopes.
82
8.7.5 Calibrating the Concentrate and Permeate Flow Rate Slopes
Calibrating the Concentrate Flow Rate Slope
1. Press ESC twice to return to the ECM-100 default menu.
2. Press the ARROW keys to scroll to the Calibration Menu (06).
3. Press ENTER to select the Calibration Menu.
4. Press ENTER to scroll to the “Conc Flow Rate Slope.”
5. Enter the passcode in the following sequence to adjust the reading:
a. HAND/AUTO
b. CIP
c. ALARM BYPASS
6. While machine is running, compare the concentrate flow rate on the ECM-100
to the bucket test concentrate flow rate measured in Step 8 of Calculating
Concentrate Flow Rate (Section 812.2).
7. If the flow rates differ by more than 0.3 gpm (0.07 m3/H) the “Conc Flow Rate
Slope” needs to be adjusted (increased or decreased to reflect the actual flow
rate of the bucket test).
8. If the flow rate displayed on the ECM-100 is less than the bucket test the
Concentrate Flow Rate Slope setting must be increased. If the flow rate
displayed on the ECM-100 is more than the bucket test the “Conc Flow Rate
Slope” must be decreased.
• Press the ARROW keys to increase or decrease the slope by increments of
2 and compare the Concentrate Flow Rate to the bucket flow rate.
• Press ENTER to save the value.
NOTE: In order for the ECM-100 to acknowledge the new slope value wait
20 seconds after ENTER is pressed for a new reading.
9. Observe “Conc Flow Rate”. If additional adjustment is necessary, repeat Step 8.
It may be necessary to repeat this process several times in order to properly
calibrate the concentrate flow rate.
If the flow reading is always low, even with a slope value of 46, refer to ECM-100
Troubleshooting (Section 4.7).
NOTE: Actual flows tend to fluctuate somewhat normally, so extreme
accuracy is often not possible.
Calibrating the Permeate Flow Rate Slope
1. Press ESC twice to return to the ECM-100 default menu.
2. Press ENTER to scroll to the Calibration Menu (06).
3. Press ENTER to select the Calibration Menu.
4. Press ENTER to scroll to the “Perm Flow Rate Slope.”
5. Enter the passcode in the following sequence to adjust the reading:
a. HAND/AUTO
b. CIP
c. ALARM BYPASS
6. While machine is running, compare the concentrate flow rate on the ECM-100
to the bucket test permeate flow rate measured in Step 8 of Calculating
Permeate Flow Rate (Section 8.12.1).
83
7. If the flow rates differ by more than 0.3 gpm (0.07 m3/h) the Permeate Flow Rate
Slope needs to be adjusted (increased or decreased to reflect the actual flow
rate of the bucket test).
8. If the flow rate displayed on the ECM-100 is less than the bucket test the
Permeate Flow Rate Slope setting must be increased. If the flow rate displayed
on the ECM-100 is more than the bucket test the Permeate Flow Rate Slope
must be decreased.
• Press the ARROW keys to increase the slope by increments of 2 and
compare the Permeate Flow Rate to the bucket flow rate.
• Press ENTER to save the value.
NOTE: It will take 20 seconds after ENTER is pressed for a new reading for
the ECM-100 to acknowledge the new slope value.
9. Observe Permeate Flow Rate. If additional adjustment is necessary, repeat
Step 8.
It may be necessary to repeat this process several times in order to properly
calibrate the concentrate flow rate.
If the flow reading is always low, even with a slope value of 46, refer to ECM-100
Troubleshooting (Section 4.7).
NOTE: Actual flows tend to fluctuate. Extreme accuracy is not required.
84
9.0 RETURNED GOODS AUTHORIZATION PROCEDURE
When you wish to return any material for repair, warranty evaluation and/or credit, please have your
original sales order or invoice available when you call Osmonics. Call Osmonics Medical Kent Facility
at (800) 633-3080 and speak with Technical Service. An Osmonics Technical Service representative
will provide instructions and a return authorization number. This number must be clearly
written on the outside of the box used to return your materials. All material must be shipped to
Osmonics with the freight prepaid by the customer. Call our Osmonics Customer Support Center
with any questions or issues concerning freight claims and a representative will discuss your situation.
All materials to be returned must be rendered into a non-hazardous condition prior to shipping.
10.0 WARRANTY/GUARANTEE
10.1 Machine Warranty/Guarantee
Seller warrants its products to be free from defects in material or workmanship for a period
of 15 months from receipt or 12 months from start-up/first use of the product, whichever
occurs first, but only when said products are operated at all times in accordance with Seller’s
written instructions. This warranty does not apply to replaceable parts or components
normally subject to wear and replacement.
Unless stated specifically on a formal, official “Performance Warranty Document” signed by
an officer or director level employee of the Seller and an employee of the Buyer who is
authorized to make such representations, there is no performance warranty on products or
warranty on process results.
SELLER EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL AND/OR
CONSEQUENTIAL DAMAGES INCLUDING, WITHOUT LIMITATIONS, LOST PROFITS.
THIS WARRANTY IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. BUYER ASSUMES
ALL LIABILITIES FOR USE AND MISUSE BY BUYER, ITS AGENTS OR ASSIGNEES.
Buyer shall give immediate notice in writing to Seller if products or components thereof or
performance (where applicable) appear defective, and shall provide Seller with reasonable
opportunity to make inspections, tests and repairs using the most efficient and cost-effective
methods available for such products or components. If Seller is not responsible under the
terms of this document and/or any formal performance warranty, Buyer shall pay Seller the
costs and expenses of such inspections, tests and repairs.
Seller’s obligation under this warranty is limited to the repair or replacement at its factory,
for the original user, of any product or component part thereof which shall prove to have
been defective. No allowance will be made for repairs or alterations made by the Buyer
without the Seller’s written consent or approval.
In no event shall Seller be liable to Buyer for any amount, including costs incurred or
expended by Seller in attempting to correct any product deficiency, relating to any claim by
Buyer against Seller in excess of the aggregate total purchase price under this contract. No
changes or expenses incident to any claim will be allowed. The remedies provided herein are
exclusive, and Seller shall incur no liability other than that stated herein.
85
10.2 Membrane Element Warranty/Guarantee
Osmonics, Inc. guarantees the proposed product to be free from defects in material or
workmanship when operated in accordance with written instructions for a period of one
year from start-up or 15 months from receipt, whichever is shorter. Parts not manufactured
by Osmonics are covered by their manufacturers’ warranties which are normally for one
year.
Osmonics’ spiral-wound membrane elements are guaranteed to operate within
specifications when used for general water treatment for a period of 24 months from receipt
providing the membrane elements have not been abused by operating at high temperatures,
high or low pH, on undisinfected water, on solutions which tend to precipitate, or system
component malfunction and when said products are operated at all times in accordance with
Seller’s written instructions.
Limitations on pH and temperature can vary with membrane type and the application of the
equipment. For general water treatment, pH should be kept between 3.0 and 7.0 with a
temperature below 85°F (29°C) unless specifically designed for higher temperatures. For
special applications or for pH or temperature ranges outside the stated limits, Osmonics may
reduce the warranty period.
SELLER EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL AND/OR
CONSEQUENTIAL DAMAGES INCLUDING, WITHOUT LIMITATIONS, LOST PROFITS.
THIS WARRANTY IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. BUYER ASSUMES
ALL LIABILITIES FOR USE AND MISUSE BY BUYER, ITS AGENTS OR ASSIGNEES.
A membrane element which fails to perform satisfactorily within the first 90 days after
receipt, has not been mishandled, and is returned to the factory, will be replaced free of
charge except for freight and local labor. If a membrane element fails to perform satisfactorily
during the balance of the warranty period and with the return of the membrane element to
the factory, Osmonics will replace the membrane element with a new membrane element
and will charge the User for the portion of the 24 months that the membrane element was
used plus incoming freight and local labor. Such pro rata charges will be based on the
replacement price prevailing at the time of warranty consideration. A new membrane
element supplied under warranty terms will carry the standard 24 month new membrane
element warranty.
If a membrane element is to be returned for warranty inspection, the User must obtain a
Return Materials Order (RMO) number from Osmonics before returning the membrane
elements. Membrane elements are to be returned freight prepaid to Osmonics, and
Osmonics will return any warranty replacement membrane elements to the customer
prepaid. Membrane elements must be kept damp at all times and must be clean and bagged,
in a non-hazardous condition, in a watertight bag before returning. Only Osmonics’
approved cleaners, biocides, dispersants or other chemicals may be used with the membrane
elements. Use of other chemicals may void the warranty. The User is responsible for
knowing the membrane element membrane material and for ensuring that chemicals harmful
to the membrane are never in contact with the membrane elements.
It is the obligation of the User to maintain frequent operating data records. Osmonics
requires these records in the warranty evaluation. User must notify Osmonics at the very
first sign of changes in operation of the Osmonics 23G machine or membrane elements.
Such notification should be in writing and should include all data requested on the operating
log sheets.
86
11.0 SPARE PARTS LISTS
87
Flow Block and Connectors Part Number
Connector, PPL, 1/4 inch Tube x 1/8 inch MPT OS1110039
Elbow, PPL, 90° , 1/4 inch Tube x 1/4 inch MPT OS1110129
Elbow, PPL, 90° , 3/8 inch Tube x 1/4 inch MPT OS1110069
Elbow, PPL, 90° , 1/4 inch Tube x 1/8 inch MPT OS1110301
Tee, PPL, 3-way, 1/4 inch Tube x 1/4 inch Tube x 1/4 inch Tube OS1110305
Tee, PPL, 3-way, 1/4 inch Tube x 1/4 inch Tube x 1/8 inch MPT OS1143153
Tee, PPL, 3-way, 1/4 inch Tube x 1/4 inch Tube x 1/4 inch MPT OS1110306
Plug, Pipe, Nylon, Square, 1/8 inch MPT OS1110036
Plug, Pipe, Nylon, Square, 1/4 inch MPT OS1110519
Plug, Pipe, Nylon, Square 1/2 inch MPT OS1112653
Plug, Pipe, Nylon, Square 1 inch MPT OS1111742
Tubing, Polyethylene, .25 inch, Blue 60067
Tubing, Polyethylene, .375 inch, Blue 60049
Coupling, Delrin, 3/8 inch MNPT x Body (Female Coupling for Permeate OS1162024
Manifold)
Coupling, Delrin, 3/8 inch Tube x Insert (Attaches to P/N OS1162024) OS1162025
88
Membrane Elements
Machine Type Part Number
423G OS1229398
WARNING: Installation of membrane elements other than those specified for the
machine as shown above can cause premature membrane element failure,
may void warranty, and may invalidate 510 (K) acceptance of a specific
machine.
89
Miscellaneous Part Number
Kit, Expansion, Frame (Required to expand machine from 4 to 10 housings) OS1158312
Kit, Expansion, Frame, EL (Required to expand to 11 or 12 housings) OS1159055
Kit, SHA Expansion (Plumbing parts provided to add 1 Stainless Steel Housing, OS1157184
Membranes Extra)
Permeate Pressure Relief Kit OS1157220
Monitor, Remote Alarm - Single Channel OS1158313
Monitor, Remote Alarm - Six Channel OS1162029
Foot, Self-Leveling, Threaded (Used with 1-1/2 inch or 1-1/2 inch Adapter) OS1156927
Adapter, 1-1/4 inch, Square (1 Each, Used on Frame Extension Only) OS1158310
Adapter, 1-1/2 inch, Square (3 Each, Used on “Main” 23G Frame) OS1158311
Plumbing, High Pressure, Spool Piece, 3/4 x 8-1/4 inch (Used in Front of Concentrate OS1156775
Return Plumbing in place of Housing)
Plumbing, Intermediate, Stainless Steel, 1 inch (U-Shaped Concentrate Crossover OS1155820
Plumbing)
pH Test Kit, Range 4-10 Standard Units OS1155478
Large Casters (3 required) OS1160132
Small Casters (1 required with three of OS1160132) OS1160133
ECM-100 Main Circuit Assembly (PCA) Replacement OS1159121
Lexan Cover Replacement OS1156570
NOTE: Machine expansion may require a change in pump and motor assembly. Contact your
equipment supplier.
NOTE: Please provide the Model and Serial number of your machine when calling for information.
90
Pump and Motor Assemblies (Three-Phase, 50 Hz)
Pump and Motor
Assembly Part Pump Out
23G Number Overall
Motor Model* Length Flow
(hp) # of Voltage (Center to Pattern
Elements Center)
Part
(380)
Number
2 OS1221470 OS1203384 5.6” (14.2 cm) 1-1
3 OS1221470 OS1203384 5.6” (14.2 cm) 2-1
3 4 OS1221470 OS1203384 5.6” (14.2 cm) 1-1-1-1
5 OS1221470 OS1203384 5.6” (14.2 cm) 2-1-1-1
6 OS1221470 OS1203384 5.6” (14.2 cm) 2-2-1-1
7 OS1222537 OS1160150 17.85” (45.3 cm) 2-2-2-1
8 OS1222537 OS1160150 17.85” (45.3 cm) 2-2-2-2
5
9 OS1222537 OS1160150 17.85” (45.3 cm) 3-2-2-2
10 OS1222537 OS1160150 17.85” (45.3 cm) 3-3-2-2
91
Pump and Motor Assemblies (Single-Phase, 60 Hz)
Pump and Motor
Assembly Part Pump Out
23G Number Overall
Motor Model* Length Flow
(hp) # of Voltage (Center to Pattern
Elements Center)
Part
(230)
Number
2 OS1221459 OS1223706 7.9” (17.5 cm) 1-1
3 OS1221459 OS1223706 7.9” (17.5 cm) 2-1
3 4 OS1221459 OS1223706 7.9” (17.5 cm) 1-1-1-1
5 OS1221459 OS1223706 7.9” (17.5 cm) 2-1-1-1
6 OS1221459 OS1223706 7.9” (17.5 cm) 2-2-1-1
7 OS1221465 OS1223741 22.41” (49.3 cm) 2-2-2-1
8 OS1221465 OS1223741 22.41” (49.3 cm) 2-2-2-2
5
9 OS1221465 OS1223741 22.41” (49.3 cm) 3-2-2-2
10 OS1221465 OS1223741 22.41” (49.3 cm) 3-3-2-2
* Pumps and motor assemblies manufactured prior to February 2000 used different pump and motor assemblies
than shown above due to a change in actual motor size. Contact your equipment supplier for assistance with
ordering the correct item(s).
92
This page intentionally left blank.
93
12.0 START-UP DATA - COMPLETED AT START UP
Customer: Date:
Model No.: Tested By:
Serial No.: ACT = Actual
94
This page intentionally left blank.
95
Customer: Date:
Model No.: Alarms Set By:
Serial No.:
13.0
96
Pressure Low Auto-On Period Offset
Primary Pressure Auto-On Duration Perm. Flowrate
High Offset
Primary Pressure Conc. Flowrate Slope
Low Perm. Flowrate Slope
Permeate Pressure pH Low Calibrate
High pH High Calibrate
Rejection Low
Pre-Filter Delta-P
High
Membrane Delta-P
23G MACHINE ALARM PRESETS LOG SHEET - COMPLETED AT START UP
High
Permeate Flow Low
This page intentionally left blank.
97
DAILY LOG FOR NAME OF CLINIC/HOSPITAL: _____________________
NOMENCLATURE OSMONICS 23G MACHINES
PERIOD OF THIS SHEET: ___________ TO ___________
PRESS = PRESSURE
WASTE = CONCENTRATE (BLOW-BY) Qc MACHINE MODEL NO: ________________
PERM = PERMEATE (PURE WATER) Qp
TEMP = TEMPERATURE NOTE: Please record all calibrations of instruments or other
COND = CONDUCTIVITY SERIAL NUMBER: _____________________
14.0
98
PERM COND (mS) Cp
% REJECTION
pH (ECM-100)
pH (MANUAL)
CALIBRATED pH (
FILTER CHANGE ( ) & TYPE
CLEAN ( )
SANITIZE ( )
FEED CHLORINE (ppm)
FEED TOTAL CHLORINE ( ppm )
FEEDWATER HARDNESS (gpg or ppm)
OPERATOR’S INITIALS
99
15.0 OSMONICS EQUIPMENT CLEANING/DISINFECT LOG SHEET
100
This page intentionally left blank.
101