Professional Documents
Culture Documents
Ka01418den 0221-00
Ka01418den 0221-00
21
71541970 Products Solutions Services
2022-02-01
Serial number
2. www.endress.com/deviceviewer Endress+Hauser
Operations App
3.
A0023555
2 Endress+Hauser
Flowmeter Proline 400 Brief Operating Instructions for flowmeter
Endress+Hauser 3
Table of contents Flowmeter Proline 400
Table of contents
1 About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Requirements for the personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6 IT security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7 Device-specific IT security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Turning the display module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Turning the transmitter housing: Promag D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3 Turning the transmitter housing: Promag L and W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4 Transmitter post-installation check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1 Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2 Connection conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3 Connecting the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.4 Ensuring potential equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.5 Special connection instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.6 Ensuring the degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.7 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6 Operation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.1 Overview of operation methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.2 Structure and function of the operating menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6.3 Access to the operating menu via the Web browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.4 Access to the operating menu via the operating tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7 System integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8.2 Switching on the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8.3 Setting the operating language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8.4 Configuring the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9 Diagnostic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4 Endress+Hauser
Flowmeter Proline 400 About this document
Permitted Preferred
Procedures, processes or actions that Procedures, processes or actions that
are permitted. are preferred.
Forbidden Tip
Procedures, processes or actions that Indicates additional information.
are forbidden.
Endress+Hauser 5
About this document Flowmeter Proline 400
Symbol Meaning
LED LED
Light emitting diode is on. Light emitting diode is flashing.
Open-ended wrench
6 Endress+Hauser
Flowmeter Proline 400 Safety instructions
2 Safety instructions
2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
‣ Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣ Are authorized by the plant owner/operator.
‣ Are familiar with federal/national regulations.
‣ Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the application).
‣ Follow instructions and comply with basic conditions.
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or where there is an
increased risk due to process pressure, are labeled accordingly on the nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣ Keep within the specified pressure and temperature range.
‣ Only use the measuring device in full compliance with the data on the nameplate and the
general conditions listed in the Operating Instructions and supplementary documentation.
‣ Based on the nameplate, check whether the ordered device is permitted for the intended
use in the hazardous area (e.g. explosion protection, pressure vessel safety).
‣ Use the measuring device only for media to which the process-wetted materials are
sufficiently resistant.
‣ If the ambient temperature of the measuring device is outside the atmospheric
temperature, it is absolutely essential to comply with the relevant basic conditions as
specified in the device documentation.
‣ Protect the measuring device permanently against corrosion from environmental
influences.
The measuring device is optionally tested in accordance with OIML R49: 2006 and has
an EC type-examination certificate according to Measuring Instruments Directive
2004/22/EC (MID) for service subject to legal metrological control ("custody transfer")
for cold water (Annex MI-001).
The permitted medium temperature in these applications is 0 to +50 °C (+32 to +122 °F).
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage caused
by improper or non-designated use.
Endress+Hauser 7
Safety instructions Flowmeter Proline 400
LWARNING
Danger of breakage due to corrosive or abrasive fluids and ambient conditions!
‣ Verify the compatibility of the process fluid with the sensor material.
‣ Ensure the resistance of all fluid-wetted materials in the process.
‣ Keep within the specified pressure and temperature range.
NOTICE
Verification for borderline cases:
‣ For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in
verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
Residual risks
LWARNING
If the temperature of the media or electronics unit is high or low, this may cause the
surfaces of the device to become hot or cold. This poses a risk of burns or frostbite!
‣ In the case of hot or cold medium temperatures, install appropriate protection against
contact.
By selecting the order option for UKCA marking, Endress+Hauser confirms a successful
evaluation and testing of the device by affixing the UKCA mark.
Contact address Endress+Hauser UK:
Endress+Hauser Ltd.
Floats Road
Manchester M23 9NF
United Kingdom
www.uk.endress.com
2.6 IT security
Our warranty is valid only if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the settings.
IT security measures, which provide additional protection for the device and associated data
transfer, must be implemented by the operators themselves in line with their security
standards.
3 Product description
The device consists of a transmitter and a sensor.
Two device versions are available:
• Compact version - transmitter and sensor form a mechanical unit.
• Remote version - transmitter and sensor are mounted in separate locations.
For detailed information on the product description, see the Operating Instructions for
the device → 3
Endress+Hauser 9
Installation Flowmeter Proline 400
4 Installation
For detailed information about mounting the sensor, see the Sensor Brief Operating
Instructions → 3
1. 4 x TX 20 3. 4.
2.
O TO
E
E H
V
R US
M
P
O TO
E
E H
V
R US
M
P
A0032091
LWARNING
Excessive tightening torque applied to the fixing screws!
Damage to the transmitter.
‣ Tighten the fixing screws with the specified torques.
1. Insert the display module and lock it when doing so.
2. Close the housing cover.
3. Tighten the fixing screws of the housing cover: tightening torque for aluminum housing
2.5 Nm (1.8 lbf ft) – plastic housing 1 Nm (0.7 lbf ft).
10 Endress+Hauser
Flowmeter Proline 400 Installation
1. 4 x TX 20 3. 4.
2.
O TO
E
E H
V
R US
M
P
V O
T
E
E H
O
R US
M
P
A0032086
6.
5. 2 x 3 mm
O TO
O TO
E
E
E H
V
E H
V
R US
R US
M
M
P
A0032087
Endress+Hauser 11
Installation Flowmeter Proline 400
7. 5x TX 20 8.
O TO
E
E H
V
R US
M
P
O TO
E
E H
V
R US
M
P
A0032130
9. 10. 4 x
O TO
E
4 mm
E H
V
R US
M
P
A0032131
12 Endress+Hauser
Flowmeter Proline 400 Installation
12.
11.
A0032132
NOTICE
Incorrect routing of the connecting cables between the sensor and transmitter in the
transmitter housing!
This can interfere with the measuring signal.
‣ Route the connecting cables directly at the level of the plugs.
LWARNING
Excessive tightening torque applied to the fixing screws!
Damage to the transmitter.
‣ Tighten the fixing screws with the specified tightening torques.
1. Fit the transmitter housing.
2. Tighten the fixing screws of the transmitter housing: tightening torque
5.5 Nm (4.1 lbf ft).
3. Slide the electronics module into the main electronics module.
4. Insert the main electronics module.
5. Tighten the fixing screws of the main electronics module: tightening torque
1.5 Nm (1.1 lbf ft).
Endress+Hauser 13
Installation Flowmeter Proline 400
NOTICE
Plug of the smart sensor electronics module connected incorrectly!
No measuring signal is output.
‣ Plug in the plug of the smart sensor electronics module as per the coding.
V O
T
E
E H
O
R US
M
P
A0021585
6. Plug in the intelligent sensor electronics module: pay attention to the coding!
7. Tighten the fixing screws of the intelligent sensor electronics module: tightening torque
0.6 Nm (0.4 lbf ft).
8. Insert the display module and lock it when doing so.
9. Close the housing cover.
10. Tighten the fixing screws of the main electronics module: tightening torque for
aluminum housing 2.5 Nm (1.8 lbf ft) – tightening torque for plastic housing
1 Nm (0.7 lbf ft).
14 Endress+Hauser
Flowmeter Proline 400 Installation
1. 4 x TX 20 3. 4.
2.
O TO
E
E H
V
R US
M
P
V O
T
E
E H
O
R US
M
P
A0032086
6.
5. 2 x 3 mm
O TO
O TO
E
E
E H
V
E H
V
R US
R US
M
M
P
A0032087
Endress+Hauser 15
Installation Flowmeter Proline 400
7. 4x TX 20 8.
O TO
E
E H
V
R US
M
P
O TO
E
E H
V
R US
M
P
A0032088
9. 4x 4 mm
11.
10.
A0032089
9. Loosen the fixing screws of the transmitter housing (when reassembling, pay attention
to the tightening torque.
10. Lift the transmitter housing.
11. Turn the housing to the desired position in increments of 90°.
16 Endress+Hauser
Flowmeter Proline 400 Installation
LWARNING
Excessive tightening torque applied to the fixing screws!
Damage to the transmitter.
‣ Tighten the fixing screws with the specified tightening torques.
1. Fit the transmitter housing.
2. Tighten the fixing screws of the transmitter housing: tightening torque
5.5 Nm (4.1 lbf ft).
3. Insert the main electronics module.
4. Tighten the fixing screws of the main electronics module: tightening torque
1.5 Nm (1.1 lbf ft).
NOTICE
Plug of the smart sensor electronics module connected incorrectly!
No measuring signal is output.
‣ Plug in the plug of the smart sensor electronics module as per the coding.
O TO
E
E H
V
R US
M
P
A0021585
5. Plug in the intelligent sensor electronics module: pay attention to the coding!
6. Tighten the fixing screws of the intelligent sensor electronics module: tightening torque
0.6 Nm (0.4 lbf ft).
7. Insert the display module and lock it when doing so.
8. Close the housing cover.
9. Tighten the fixing screws of the main electronics module: tightening torque for
aluminum housing 2.5 Nm (1.8 lbf ft) – for plastic housing 1 Nm (0.7 lbf ft).
Endress+Hauser 17
Installation Flowmeter Proline 400
18 Endress+Hauser
Flowmeter Proline 400 Electrical connection
5 Electrical connection
NOTICE
The measuring device does not have an internal circuit breaker.
‣ For this reason, assign the measuring device a switch or power-circuit breaker so that the
power supply line can be easily disconnected from the mains.
‣ Although the measuring device is equipped with a fuse, additional overcurrent protection
(maximum 16 A) should be integrated into the system installation.
Power supply cable (incl. conductor for the inner ground terminal)
Standard installation cable is sufficient.
Signal cable
EtherNet/IP
The standard ANSI/TIA/EIA-568-B.2 Annex specifies CAT 5 as the minimum category for a
cable used for EtherNet/IP. CAT 5e and CAT 6 are recommended.
For more information on planning and installing EtherNet/IP networks, please refer to
the "Media Planning and Installation Manual. EtherNet/IP" of ODVA Organization
Endress+Hauser 19
Electrical connection Flowmeter Proline 400
Cable diameter
• Cable glands supplied:
• For standard cable: M20 × 1.5 with cable 6 to 12 mm (0.24 to 0.47 in)
• For reinforced cable: M20 × 1.5 with cable 9.5 to 16 mm (0.37 to 0.63 in)
• (Plug-in) spring terminals for wire cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG)
20 Endress+Hauser
Flowmeter Proline 400 Electrical connection
NOTICE
Insufficient sealing of the housing!
Operational reliability of the measuring device could be compromised.
‣ Use suitable cable glands corresponding to the degree of protection.
1. Remove dummy plug if present.
2. If the measuring device is supplied without cable glands:
Provide suitable cable gland for corresponding connecting cable.
3. If the measuring device is supplied with cable glands:
Observe requirements for connecting cables → 19.
Endress+Hauser 21
Electrical connection Flowmeter Proline 400
Transmitter
Electrode cable Coil current cable
90 (3.54)*
100 (3.94)*
70 (2.76)
80 (3.15) 50 (1.97)
17 (0.67) 50 (1.97) 8 (0.31) 10 (0.39)
8 (0.31)
A A
1
2 1
1
2
1 B B
GND A0032096
2
2 2 Engineering unit mm (in)
A0032093
22 Endress+Hauser
Flowmeter Proline 400 Electrical connection
Sensor
Electrode cable Coil current cable
A A
1 1
2 1
³1 (0.04)
2 1
GND
2 B
A0032101
B 1
A0032100
Endress+Hauser 23
Electrical connection Flowmeter Proline 400
3.
GND
E1
E2
5 7 4 37 42 41
A0032134
24 Endress+Hauser
Flowmeter Proline 400 Electrical connection
Promag L and W
3.
42 41
GND
E1
E2
E
37 4 7 5
A0032103
Push the cable through the cable entry. To ensure tight sealing, do not remove the
sealing ring from the cable entry.
Endress+Hauser 25
Electrical connection Flowmeter Proline 400
5. Strip the cable and cable ends. In the case of stranded cables, also fit ferrules → 21.
6. Connect the cable in accordance with the terminal assignment .
7. Firmly tighten the cable glands.
8. LWARNING
Housing degree of protection may be voided due to insufficient sealing of the
housing.
‣ Screw in the screw without using any lubricant. The threads on the cover are coated
with a dry lubricant.
1. 4 x T 20
2.
4.
GND
E1
E2
S1
S2
E
S
6 5 7 8 4 37 36 42 41
3.
A0032102
26 Endress+Hauser
Flowmeter Proline 400 Electrical connection
7. LWARNING
Housing degree of protection may be voided due to insufficient sealing of the
housing.
‣ Screw in the screw without using any lubricant.
Reverse the removal procedure to reassemble the transmitter.
Endress+Hauser 27
Electrical connection Flowmeter Proline 400
1. 4 x T 20
2.
5.
L+/L
L-/N
B A
2627
6. 1 2
10 (0.4)
3.
4.
A0038322
28 Endress+Hauser
Flowmeter Proline 400 Electrical connection
5. Connect the cables according to the connection nameplate on the main electronics
module, for supply voltage: open the shock protection cover.
6. Firmly tighten the cable glands.
1. 4 x T 20
2.
8.
3.
4. 9.
22 mm
7.
24 mm
5. 6.
10 (0.4)
A0038184
Endress+Hauser 29
Electrical connection Flowmeter Proline 400
4.
3.
2.
1. 5.
22 mm
24 mm
A0038185
30 Endress+Hauser
Flowmeter Proline 400 Electrical connection
PE = PP = PM PE = PP = PM
A0044854 A0045825
7 Promag L, W 8 Promag D
Endress+Hauser 31
Electrical connection Flowmeter Proline 400
‣ Connect the connection housing of the transmitter or sensor to ground potential by means
of the ground terminal provided for this purpose.
DN ≤ 300 DN ≥ 350
PE = PP = PM
A0042089
9 Promag L, W
1. Connect both sensor flanges to the pipe flange via a ground cable and ground them.
2. Connect the connection housing of the transmitter or sensor to ground potential by
means of the ground terminal provided for this purpose.
3. If DN ≤ 300 (12"): Mount the ground cable directly on the conductive flange coating of
the sensor with the flange screws.
4. If DN ≥ 350 (14"): Mount the ground cable directly on the metal transport bracket.
Observe the screw tightening torques: see the Brief Operating Instructions for the
sensor.
32 Endress+Hauser
Flowmeter Proline 400 Electrical connection
Starting conditions:
• The pipe has an insulating effect.
• Low-impedance medium grounding close to the sensor is not guaranteed.
• Equalizing currents through the medium cannot be ruled out.
PE = PP = PM PE = PP = PM
A0044856 A0045824
10 Promag L, W 11 Promag D
Promag D
1. Connect flanges to the ground terminal of the transmitter's or sensor's connection
housing via the ground cable.
2. Connect the connection to ground potential.
Promag L and W
1. Connect ground disks to the ground terminal of the transmitter's or sensor's connection
housing via the ground cable.
2. Connect the connection to ground potential.
5.4.3 Connection example with the potential of the medium not equal to the
protective ground
In these cases, the medium potential can differ from the potential of the device.
Endress+Hauser 33
Electrical connection Flowmeter Proline 400
3. 3.
+ +
2. – 2. –
PE ≠ PP = PM PE ≠ PP = PM
A0042253 A0045826
12 Promag L, W 13 Promag D
1. Connect the pipe flanges and transmitter via the ground cable.
2. Route the shielding of the signal lines via a capacitor (recommended value 1.5µF/50V).
3. Device connected to power supply such that it is floating in relation to the protective
earth (isolation transformer). This measure is not required in the case of 24V DC supply
voltage without PE (= SELV power unit).
5.4.4 Promag W: Connection examples with the potential of the medium not equal to
the protective ground with the "Measurement isolated from ground" option
In these cases, the medium potential can differ from the potential of the device.
Introduction
The "Measurement isolated from ground" option enables the galvanic isolation of the
measuring system from the device potential. This minimizes harmful equalizing currents
caused by differences in potential between the medium and the device. The "Measurement
isolated from ground" option is optionally available: order code for "Sensor option", option CV
Operating conditions for the use of the "Measurement isolated from ground" option
Device version Compact version and remote version
(Length of connecting cable ≤ 10 m)
Differences in voltage between medium potential and device As small as possible, usually in the mV range
potential
Alternating voltage frequencies in the medium or at ground Below typical power line frequency in the country
potential (PE)
34 Endress+Hauser
Flowmeter Proline 400 Electrical connection
Plastic pipe
Sensor and transmitter are correctly grounded. A difference in potential can occur between
the medium and protective earth. Potential equalization between PM and PE via the reference
electrode is minimized with the "Measurement isolated from ground" option.
Starting conditions:
• The pipe has an insulating effect.
• Equalizing currents through the medium cannot be ruled out.
PE = PP ≠ PM
A0044855
14 Promag W
1. Use the "Measurement isolated from ground" option, while observing the operating
conditions for measurement isolated from ground.
2. Connect the connection housing of the transmitter or sensor to ground potential by
means of the ground terminal provided for this purpose.
Endress+Hauser 35
Electrical connection Flowmeter Proline 400
3.
+
2. –
PE ≠ PP ≠ PM
A0044857
15 Promag W
1. Connect the pipe flanges and transmitter via the ground cable.
2. Route the shielding of the signal cables via a capacitor (recommended value 1.5µF/
50V).
3. Device connected to power supply such that it is floating in relation to the protective
earth (isolation transformer). This measure is not required in the case of 24V DC supply
voltage without PE (= SELV power unit).
4. Use the "Measurement isolated from ground" option, while observing the operating
conditions for measurement isolated from ground.
36 Endress+Hauser
Flowmeter Proline 400 Electrical connection
EtherNet/IP
1 2 3 4
A0028767
Endress+Hauser 37
Electrical connection Flowmeter Proline 400
To guarantee IP66/67 degree of protection, Type 4X enclosure, carry out the following steps
after the electrical connection:
1. Check that the housing seals are clean and fitted correctly. Dry, clean or replace the
seals if necessary.
2. Tighten all housing screws and screw covers.
3. Firmly tighten the cable glands.
4. To ensure that moisture does not enter the cable entry, route the cable so that it loops
down before the cable entry ("water trap").
A0029278
5. Insert dummy plugs (corresponding to the housing degree of protection) into unused
cable entries.
NOTICE
Standard dummy plugs used for transportation do not have the appropriate degree of
protection and can result in damage to the device!
‣ Use suitable dummy plugs corresponding to the degree of protection.
5.6.2 Degree of protection IP68, Type 6P enclosure, with "Cust-potted" option
Depending on the version, the sensor meets all the requirements of IP68 degree of protection,
Type 6P enclosure and can be used as a remote version .
The degree of protection of the transmitter is always only IP66/67, Type 4X enclosure and the
transmitter must therefore be treated accordingly → 38.
To guarantee IP68 degree of protection, Type 6P enclosure for the "Cust-potted" options, carry
out the following steps after the electrical connection:
1. Firmly tighten the cable glands (torque: 2 to 3.5 Nm) until there is no gap between the
bottom of the cover and the housing support surface.
2. Firmly tighten the union nut of the cable glands.
3. Pot the field housing with a potting compound.
38 Endress+Hauser
Flowmeter Proline 400 Electrical connection
4. Check that the housing seals are clean and fitted correctly. Dry, clean or replace the
seals if necessary.
5. Tighten all housing screws and screw covers (torque: 20 to 30 Nm).
Endress+Hauser 39
Electrical connection Flowmeter Proline 400
40 Endress+Hauser
Flowmeter Proline 400 Operation options
6 Operation options
6.1 Overview of operation methods
ESC
- + E
1 2 3 4 5 6
A0046501
For custody transfer, once the device has been put into circulation or sealed, its operation
is restricted.
Endress+Hauser 41
Operation options Flowmeter Proline 400
Operation
task-oriented
Setup
Diagnostics
Expert function-oriented
A0014058-EN
42 Endress+Hauser
Flowmeter Proline 400 Operation options
6.3.2 Prerequisites
Computer hardware
Hardware Interface
CDI-RJ45 WLAN
Interface The computer must have an RJ45 The operating unit must have a
interface. WLAN interface.
Connection Standard Ethernet cable with RJ45 Connection via Wireless LAN.
connector.
Computer software
Software Interface
CDI-RJ45 WLAN
Endress+Hauser 43
Operation options Flowmeter Proline 400
Computer settings
Settings Interface
CDI-RJ45 WLAN
User rights Appropriate user rights (e.g. administrator rights) for TCP/IP and proxy server
settings are necessary (for adjusting the IP address, subnet mask etc.).
Proxy server settings of the Web The Web browser setting Use a Proxy Server for Your LAN must be deselected .
browser
Ifenter
JavaScript cannot be enabled:
http://192.168.1.212/basic.html in the address line of the Web
browser. A fully functional but simplified version of the operating menu
structure starts in the Web browser.
Network connections Only the active network connections to the measuring device should be used.
Switch off all other network Switch off all other network
connections such as WLAN. connections.
44 Endress+Hauser
Flowmeter Proline 400 Operation options
4 128
3 64
2 32
IP Address
(last octet)
1 16
setting
4 8
3 4
2 2
1 1
A0023353
• Once the DIP switch has been activated, the device must be restarted
before the device uses the default IP address.
• If the default IP address is used (top DIP switch No. 2 = ON), there is no
connection to the EtherNet/IP network.
Web server Web server and WLAN must be enabled; factory setting: ON
• Once the DIP switch has been activated, the device must be restarted
before the device uses the default IP address.
• If the default IP address is used (top DIP switch No. 2 = ON), there is no
connection to the EtherNet/IP network.
Endress+Hauser 45
Operation options Flowmeter Proline 400
IP address 192.168.1.XXX; for XXX all numerical sequences except: 0, 212 and 255 → e.g.
192.168.1.213
46 Endress+Hauser
Flowmeter Proline 400 Operation options
To ensure the safe and swift assignment of the WLAN network to the measuring point,
it is advisable to change the SSID name. It should be possible to clearly assign the SSID
name to the measuring point (e.g. tag name) as it is displayed as the WLAN network.
Disconnecting
‣ After configuring the device:
Terminate the WLAN connection between the operating unit and measuring device.
Endress+Hauser 47
Operation options Flowmeter Proline 400
2. Enter the IP address of the Web server in the address line of the Web browser:
192.168.1.212
The login page appears.
If a login page does not appear, or if the page is incomplete, see the Special
Documentation for the Web server
6.3.4 Logging on
1
2
A0029418
1 Function row
2 Local display language
3 Navigation area
Header
The following information appears in the header:
• Device name
• Device tag
• Device status with status signal
• Current measured values
Function row
Functions Meaning
48 Endress+Hauser
Flowmeter Proline 400 Operation options
Functions Meaning
Device status Displays the diagnostic messages currently pending, listed in order of priority
Configuration and checking of all the parameters required for establishing the connection to the
Network measuring device:
configuration • Network settings (e.g. IP address, MAC address)
• Device information (e.g. serial number, firmware version)
Navigation area
If a function is selected in the function bar, the submenus of the function open in the
navigation area. The user can now navigate through the menu structure.
Working area
Depending on the selected function and the related submenus, various actions can be
performed in this area:
• Configuring parameters
• Reading measured values
• Calling up help text
• Starting an upload/download
Navigation
"Expert" menu → Communication → Web server
Web server functionality Switch the Web server on and off. • Off
• On
Endress+Hauser 49
Operation options Flowmeter Proline 400
Option Description
If communication with the Web server was established via the default IP address
192.168.1.212, DIP switch No. 10 must be reset (from ON → OFF). Afterwards, the IP
address of the device is active again for network communication.
50 Endress+Hauser
Flowmeter Proline 400 System integration
7 System integration
For detailed information on system integration, see the Operating Instructions for the
device → 3
A detailed description of how to integrate the device into an automation system (e.g.
from Rockwell Automation) is available as a separate document:
www.endress.com→ Select your country → Solutions → Fieldbus planning
→ Fieldbus technologies → EtherNet/IP
8 Commissioning
8.1 Function check
Before commissioning the measuring device:
‣ Make sure that the post-installation and post-connection checks have been performed.
• "Post-installation check" checklist → 18
• "Post-connection check" checklist → 40
If nothing appears on the local display or a diagnostic message is displayed, refer to the
Operating Instructions for the device → 3
Endress+Hauser 51
Commissioning Flowmeter Proline 400
XXXXXXXXX
20.50
XX XX
Main menu 0104-1
1. Display language
English
Operation
Setup
Display language 0104-1
2. Ã English
Deutsch
Español
Français
Display language 0104-1
3. Ã English
Deutsch
Español
Français
Hauptmenü 0104-1
4. Sprache
Deutsch
Betrieb
Setup
A0029420
Submenu Configuration
Sensor Measured values, system units, process parameters, external compensation, sensor adjustment,
calibration
Application Totalizer
52 Endress+Hauser
Flowmeter Proline 400 Diagnostic information
9 Diagnostic information
Faults detected by the self-monitoring system of the measuring device are displayed as a
diagnostic message in alternation with the operational display. The message about remedial
measures can be called up from the diagnostic message, and contains important information
on the fault.
XXXXXXXXX S XXXXXXXXX S
20.50 S801
Supply voltage
X XX i Menu
1.
Diagnostic list S
Diagnostics 1
1 S801 Supply voltage
Diagnostics 2
Diagnostics 3
2.
3.
A0029431-EN
Endress+Hauser 53
*71541970*
71541970
www.addresses.endress.com