Rae Toxiraepid Manual
Rae Toxiraepid Manual
User’s Guide
Contents
Read Before Operating ................................................................................................... 3
1. General Information ........................................................................................................ 6
2. Specifications .................................................................................................................. 7
3. Overview ......................................................................................................................... 8
4. User Interface .................................................................................................................. 8
4.1. Display Overview .......................................................................................... 9
4.2. Status Indicator Icons ..................................................................................... 9
5. Charging The ToxiRAE Pro PID .................................................................................. 10
5.1. Removing The ToxiRAE Pro PID From The Charging Cradle .................. 11
5.2. Low Voltage Shutoff.................................................................................... 11
6. Turning The ToxiRAE Pro PID On .............................................................................. 12
7. Turning The ToxiRAE Pro PID Off ............................................................................. 13
8. Testing The Alarms (Manually).................................................................................... 13
9. Low Battery Warnings .................................................................................................. 14
10. Dead Battery Warning & Shutoff ............................................................................... 14
11. Operating The ToxiRAE Pro PID ............................................................................... 15
11.1. Overview ...................................................................................................... 15
11.1.1. Normal Mode ................................................................................................ 15
11.1.2. Basic User Mode ........................................................................................... 16
11.1.3. Advanced User Mode ................................................................................... 17
11.2. Navigation In Normal Mode ........................................................................ 17
11.2.1. TWA, STEL, Peak ........................................................................................ 18
11.2.2. Date, Time, And Temperature ...................................................................... 18
11.2.3. Wireless Settings ........................................................................................... 18
11.2.4. Calibration Gas, Measurement Gas, Correction Factor ................................ 18
11.2.5. Enter Communications and stop measurement? ........................................... 19
11.3. Programming................................................................................................ 19
11.4. Entering Programming Mode ...................................................................... 19
11.4.1. Navigating Programming Menus .................................................................. 21
11.5. Programming Menus .................................................................................... 21
11.5.1. Calibration..................................................................................................... 22
11.5.2. Measurement ................................................................................................. 23
11.5.3. Alarm Setting ................................................................................................ 24
11.5.4. Datalog .......................................................................................................... 28
11.5.5. Monitor Setup ............................................................................................... 30
11.6. Exit (Exit Programming Mode) ................................................................... 35
12. Policy Enforcement ..................................................................................................... 36
12.1. Setting Policy Enforcement ......................................................................... 36
12.1.1. AutoRAE 2 Cradle ........................................................................................ 36
12.1.2. ToxiRAE Pro PID Desktop Cradle Or Travel Charger ................................ 40
12.2. Deactivating Policy Enforcement ................................................................ 42
12.2.1. AutoRAE 2 Cradle ........................................................................................ 42
12.2.2. ToxiRAE Pro PID Desktop Cradle Or Travel Charger ................................ 42
13. Bump Testing & Calibrating The ToxiRAE Pro PID ................................................. 44
13.1. Bump Testing & Calibrating With An AutoRAE 2™ ................................. 44
13.1.1. Bump (Functional) Testing ........................................................................... 44
1
ToxiRAE Pro PID User’s Guide
2
ToxiRAE Pro PID User’s Guide
WARNINGS
Read Before Operating
This manual must be carefully read by all individuals who have or will have the
responsibility of using, maintaining, or servicing this product. The product will perform
as designed only if it is used, maintained, and serviced in accordance with the
manufacturer’s instructions.
CAUTION!
Never operate the monitor when the cover is removed. Remove the monitor top cap, rear
cover, fan, or battery only in an area known to be non-hazardous.
Product Registration
Register your product online by visiting:
http://www.raesystems.com/support/product-registration
By registering your product, you can:
3
ToxiRAE Pro PID User’s Guide
WARNINGS
Use only RAE Systems lithium-ion battery part number G02-3004-000 (3.7V,
1,800mAh). This instrument has not been tested in an explosive gas/air atmosphere
having an oxygen concentration greater than 21%. Substitution of components may
impair suitability for intrinsic safety. Replace batteries only in non-hazardous locations.
STATIC HAZARD: Clean only with a damp cloth to avoid damage from electrostatic
discharge.
For safety reasons this equipment must be operated and serviced by qualified personnel
only. Read and understand this instruction manual completely before operating or
servicing.
The monitor should be calibrated every time it does not pass a bump test, but no less
frequently than every six months, depending on use and exposure to gas and
contamination, and its operational mode.
The ToxiRAE Pro PID monitor is factory-preconfigured to a 30-day calibration interval,
so it will go into calibration alarm if it is not calibrated for 30 days or more.
• Calibration intervals and bump test procedures may vary due to national legislation.
• RAE Systems recommends using RAE calibration gas cylinders with one of the
following:
Isobutylene, 34L, 100 ppm (balance air), PN 600-0002-000
Isobutylene, 100 ppm 103L steel cylinder, PN 600-0002-001
Isobutylene Calibration Gas, 100 ppm, 34L cylinder; constant-flow CGA-600
regulator with adapter, PN 002-3025-000
Isobutylene, 100 ppm (balance air), 34L cylinder, Dry Air, 0 ppm, 34L cylinder;
Constant-flow DGA-600 regulator with adapter, PN 007-3001-000
4
ToxiRAE Pro PID User’s Guide
AVERTISSEMENT
Utiliser seulement la batterie Lithium-ion RAE Systems référence G02-3004-000 (3.7V,
1,800mAh). Cet instrument n’a pas été testé dans une atmosphère de gaz/air explosive
ayant une concentration d’oxygène plus élevée que 21%. La substitution de composants
peut compromettre la sécurité intrinsèque. Ne changer les batteries que dans un
emplacement désigné non dangereux.
Pour des raisons de sécurité, cet équipement doit être utilisé et entretenu uniquement par
un personnel qualifié. Étudier le manuel d’instructions en entier avant d’utiliser, ou
d’entretenir l’équipement.
Le ToxiRAE Pro PID est configuré en usine avec une période de calibration de 30 jours,
si il n’est pas calibré durant cette période , il passe en alarme.
Une vérification d’étalonnage est définie par une exposition du détecteur au gaz
d’étalonnage qui doit déclencher le seuil d’alarmes bas.
5
ToxiRAE Pro PID User’s Guide
1. General Information
ToxiRAE Pro PID is a personal wireless monitor for volatile organic compounds
(VOCs), the world’s smallest. Featuring RAE Systems’ next-generation PID sensor, the
ToxiRAE Pro PID can promptly detect and accurately monitor over 300 VOCs. With an
onboard library of 190 correction factors, the ToxiRAE Pro PID can be programmed to
automatically read in concentrations of the specified compound.
Key Features
1
Wireless functionality is currently offered in 2011 in North America and Europe. Contact RAE Systems for
availability in other regions.
2
Available with Industrial Hygiene configurations only.
3
Contact RAE Systems for availability.
4
Wireless versions have a functioning wireless modem and are ready for wireless deployments. “Non-
wireless” versions cannot be upgraded to wireless in the future. Additional equipment and/or software
licenses may be required to enable remote wireless monitoring and alarm transmission.
6
ToxiRAE Pro PID User’s Guide
2. Specifications
ToxiRAE Pro PID Specifications
Dimensions 118 mm x 60 mm x 30 mm (4.6" x 2.4" x 1.2")
Weight 235g (8.3 oz)
Battery Internal rechargeable Li-ion
Charging Time Less than 4 hours
Operating Time More than 12 hours on full charge (normal operation)
Charger Charging and PC communication cradle: AC / DC adapter with international
prong kit (100 to 240V, 50/60 Hz AC to 12V DC)
7
ToxiRAE Pro PID User’s Guide
3. Overview
The ToxiRAE Pro PID is a wireless, personal volatile organic compounds (VOC)
monitor, the world’s smallest. The ToxiRAE Pro PID takes worker protection to the next
level by providing safety professionals wireless access to real-time instrument readings
and alarm status from any location for better visibility and faster response. The ToxiRAE
Pro PID features RAE Systems’ next-generation PID sensor that delivers fast, reliable
detection and accurate monitoring of a wide variety of VOCs in a broad range of
temperature and humidity conditions.
4. User Interface
The ToxiRAE Pro PID’s user interface consists of the display, four LEDs, an alarm
buzzer, and two keys, [MODE] and [Y/+]. The LCD displays real-time reading in
specified measurement units, sensor type, alarm type (when in alarm, including cal.
overdue), battery status, datalog (if on), and radio and connection quality (if available).
Gas inlet
Top cap
Alarm
Buzzer
Display
[MODE] key
[Y/+] key
8
ToxiRAE Pro PID User’s Guide
Soft keys
(functions change by activity)
Icon Function
Wireless status: the radio is on
Wireless status: the radio is off
The instrument is not equipped with a radio (no icon)
Wireless strength (0 to 5 bars), only when radio is turned on
Datalogging status (shown when datalogging is on, blank when off)
Battery status (three segments show battery charge level)
Man Down alarm enabled
9
ToxiRAE Pro PID User’s Guide
Rear view of
ToxiRAE Pro PID
Raised lip on
rear of ToxiRAE Pro PID
locks into cradle’s latch
Charging status
LED
ToxiRAE Pro
Charging and PC
Communications
Cradle
Latch release
Rear view of
charging cradle Connect AC
adapter to the
charging cradle
Note: Before setting the ToxiRAE Pro PID into its charging cradle, visually inspect the
contacts to make sure they are clean. If they are not, wipe them with a soft, dry cloth. Do
not use solvents or cleaners.
10
ToxiRAE Pro PID User’s Guide
Follow this procedure to charge the ToxiRAE Pro PID (the procedure is applicable to the
instrument with or without the rubber boot installed):
1. Plug the AC/DC adapter into the ToxiRAE Pro PID’s cradle.
2. Plug the AC/DC adapter into the wall outlet.
3. Place the ToxiRAE Pro PID into the cradle and press down until it is locked in
place.
The ToxiRAE Pro PID begins charging automatically. The LED in the cradle should
glow red to indicate charging. When charging is complete, the LED in the cradle glows
green.
WARNING!
11
ToxiRAE Pro PID User’s Guide
Caution: The alarm buzzer is very loud. During startup, you can mute most of the sound
by holding a finger over the alarm buzzer port.
Note: Never put tape over the alarm buzzer port to permanently mute it or otherwise limit
the loudness of the buzzer.
1. When the ToxiRAE Pro PID turns on, the buzzer, vibration alarm, and LEDs are
tested. The firmware version is shown in the display (for example, “V1.00” indicates
firmware version 1.00).
2. A battery test is performed. If the battery has sufficient charge, then the next step is a
self test of the system.
Note: If the battery is almost fully discharged, the message “Battery too low! Needs
charging. Powering off!” shows in the display and the ToxiRAE Pro PID shuts off.
You must charge the battery before you can use the instrument.
Note: If one of the following error messages is displayed, shut off the ToxiRAE Pro
PID by pressing [MODE]:
Sensor error!
Wrong sensor!
If any of the following error messages occurs, you can either shut off the instrument
by pressing [MODE], or continue to the next startup test by pressing [Y/+]:
For any of these error types, try restarting the instrument. If the error message appears
again after five more attempts to restart the instrument, consult the distributor from
whom the instrument was purchased for technical support.
12
ToxiRAE Pro PID User’s Guide
4. After self-testing, two start-up options are available for the ToxiRAE Pro PID:
Normal and Fast Start-up. The following information is displayed in sequence under
Normal Start-up and skipped under Fast Start-up:
Sensor type
Sensor serial number
Date, time, and temperature
Calibration gas
Last calibration date
Measurement gas
Correction factor
User mode
Battery type, voltage, and shutoff voltage
Alarm mode
Buzzer enabled/disabled status
Light enabled/disabled status
Vibration alarm enabled/disabled status
Alarm settings for High, Low, STEL, and TWA
Datalog type and interval
5. Once the startup process is complete, a sensor warm-up screen is shown (with
countdown, if necessary). Then the main measurement screen is shown. The type of
monitored hazard is displayed, with current reading. The ToxiRAE Pro PID is now
ready for use.
When you see “Unit Off,” release your finger from the [MODE] key. The ToxiRAE Pro
PID is now off.
Important! If any of the alarms does not respond to this test, check the Alarm Settings. It is
possible that any or all of the alarms have been turned off. If all the alarms are turned on, but
one or more of them (buzzer, LED lights, or vibration alarm) does not respond to this test, do
not use the instrument; contact your RAE Systems distributor for technical support.
13
ToxiRAE Pro PID User’s Guide
It then automatically shuts off. You must charge the ToxiRAE Pro PID’s battery before
you can continue to use this instrument.
Important! Do not operate the ToxiRAE Pro PID again until its battery has been
charged.
WARNING!
To reduce the risk of ignition of hazardous atmospheres, charge the battery only in
areas known to be non-hazardous.
14
ToxiRAE Pro PID User’s Guide
11.1. Overview
The ToxiRAE Pro PID has two operational modes:
Normal Mode is the default mode. It is accessed when you turn on the ToxiRAE Pro
PID. Two sub-modes are available: Basic User and Advanced User. In Basic User, some
restrictions are applied, including password protection that guards against entering
Programming Mode by unauthorized personnel. In Advanced, there are no such access
restrictions (you do not need a password), and it provides the indications and data you
need most for typical monitoring applications.
Diagnostic Mode is primarily intended for technicians to use during troubleshooting, although it
also offers access to a few changeable parameters that you may rarely (if ever) need to change. A
password is required to enter Diagnostic Mode (the password is the same as (and
automatically kept in sync with) the one used to enter Programming Mode). The default
password is 0000. To enter Diagnostic Mode, power the instrument off and then turn it
back on by pressing and holding both the buttons. In Diagnostic Mode, ToxiRAE Pro PID
displays readings in raw counts instead of units such as parts per million (ppm).
It is not possible to switch to Programming from Diagnostic Mode without turning off the
instrument first and then restarting it in the desired mode.
15
ToxiRAE Pro PID User’s Guide
Note: The gray boxes indicate the datalog functions when datalogging is in Manual
mode. When datalogging is in Automatic mode, these screens do not appear. Refer to
page 28 for information on selecting Automatic or Manual datalogging.
16
ToxiRAE Pro PID User’s Guide
To exit Programming Menu and return to the measurement screen (in Advanced User
mode), press the [MODE] button repeatedly to highlight the Exit icon in Programming
Menu and press Y to exit to the measurement screen.
When the ToxiRAE Pro PID is in Advanced User mode, pressing [MODE] steps through
the same screens, but with the addition of a screen that allows for selection of different
measurement gases from the internal library. Also, once in Advanced User mode, you
may enter Programming without using a password.
Note: In Advanced User Mode, you may select different measurement gases from the
internal library.
Note: The gray box indicates the datalog functions when datalogging is in Manual mode.
When datalogging is in Automatic mode, these screens do not appear. Refer to page 28
for information on selecting Automatic or Manual datalogging.
17
ToxiRAE Pro PID User’s Guide
The first screen includes a readout for TWA, STEL, and Peak readings.
TWA The TWA (time-weighted average) reading is the average reading of the gas
concentration times that the monitor has been on, prorated to an 8-hour period.
STEL Short Term Exposure Limit (STEL) data based on 15-minute STEL values,
expressed in ppm or mg/m3. A STEL value is only displayed after the
ToxiRAE Pro PID has been on for 15 minutes or longer. After exiting PC
Communications mode, the STEL is reset.
Peak The Peak value tells you the highest reading for the sensor since the ToxiRAE
Pro PID was turned on. Press [Y/+] twice to clear the Peak value.
Note: If you do not press a key within 1 minute, the display reverts to the
normal reading.
The current Date is expressed as Month/Day/Year, with two digits for month and day,
and four digits for the year. Below the date is the time, which is expressed as
Hours/Minutes/Seconds, with two digits for each. The time is in 24-hour (military)
format. Below the time is the internal temperature, which can be in degrees Fahrenheit or
Celsius (settable in Programming Mode).
The current wireless settings are shown here. These include the PAN ID, Channel, and
Unit ID, which are helpful when creating or troubleshooting networks. Parent ID data
does not apply.
This screen shows calibration gas (Cal. Gas), measurement gas (Meas. Gas), and
correction factor (CF).
18
ToxiRAE Pro PID User’s Guide
11.3. Programming
You must provide a 4-digit password to enter Programming Mode, unless the ToxiRAE
Pro PID is already running in Advanced User mode. The default password is 0000.
If you make a mistake, you can cycle through the digits by pressing [MODE] repeatedly
and then using [Y/+] to change the number in each position.
19
ToxiRAE Pro PID User’s Guide
When you have successfully entered Programming Mode, the following screen appears:
Note: The password can only be changed by connecting the instrument to a PC running
ProRAE Studio II software. Follow the instructions in ProRAE Studio II to change it.
The Calibration icon is highlighted first by default, but you can press [MODE] to step
from one programming menu item to the next, with the name of the menu shown at the
top of the display and the corresponding icon highlighted. As you repeatedly press
[MODE], the selection moves from left to right, and the following screens appear in
sequence:
Note: When you reach Exit and press [MODE], the menu cycles back to Calibration.
To exit the Programming Menu, highlight Exit by pressing the [MODE] button, and press
the [Y/+] key.
20
ToxiRAE Pro PID User’s Guide
In the submenus, the functions of a “down arrow” and “Select” are controlled by the
[MODE] key and [Y/+] key, respectively.
Also in submenus, the functions of the keys may correspond to the instruction directly
above each key. Therefore, if it says “OK” above the [MODE] key, pressing [MODE]
selects “OK.” When setting numerical data, the [MODE] key typically selects which digit
is highlighted, while each press of [Y/+] increases the digit by 1.
This table shows the menus (and their icons) and submenus:
Note: There is also an “Exit” icon. It has only one function. When you select it, the
instrument exits Programming Mode, updates the settings, and returns to monitoring.
21
ToxiRAE Pro PID User’s Guide
Once you enter Programming, the LCD displays the first menu, Calibration. Each
subsequent menu is accessed by pressing [MODE] repeatedly until the desired menu is
displayed. To enter a submenu of a menu, press [Y/+].
11.5.1. Calibration
Two types of calibration are available: Zero (fresh air) and Span.
In the Calibration submenu, select Zero or Span Calibration by pressing [MODE]. Once
your choice is highlighted, press [Y/+].
Zero Calib
The procedure for performing a zero calibration is covered on page 36.
22
ToxiRAE Pro PID User’s Guide
Span Calib
The procedure for performing a basic span calibration is covered on page 46.
Exit
Press [Y/+] to exit. Calibration is exited, and Measurement is highlighted in the
Programming Menu screen.
11.5.2. Measurement
The submenus for Measurement are Measurement Gas and Measurement Unit.
Meas Gas
Measurement gases are organized in a list called Gas Library:
The Gas Library consists of 190 compounds found in RAE Systems’ Technical Note TN-
106 (available online at www.raesystems.com).
1. Scroll through the Gas Library by pressing [Y/+] until you find the gas you want
as your measurement gas.
2. When you are on the gas of your choice, press [MODE] to highlight “Save.”
3. To save your choice, press [Y/+]. Otherwise, press [MODE] to highlight “Quit,”
followed by [Y/+]; the newly selected gas will not be saved.
Meas Unit
Standard available measurement units include:
Abbreviation Unit
ppm parts per million
mg/m3 milligrams per cubic meter
Exit
Press [Y/+] to exit. Measurement is exited, and Alarm Setting is highlighted in the
Programming Menu screen.
23
ToxiRAE Pro PID User’s Guide
High Alarm
Set the High Alarm as follows:
1. In the High Alarm submenu, press [Y/+] repeatedly to select a desired number.
Numbers increase from 0 to 9. Once 9 is reached, pressing [Y/+] again “wraps”
around back to 0.
2. Press [MODE] to move to the next digit.
3. When you are satisfied with the number, press [MODE] until “OK” is
highlighted.
4. To save the new value, press [Y/+]. The value is saved, and the menu advances to
Low Alarm.
Low Alarm
Set the Low Alarm as follows:
1. In the Low Alarm submenu, press [Y/+] repeatedly to select a desired number.
Numbers increase from 0 to 9. Once 9 is reached, pressing [Y/+] again “wraps”
around back to 0.
2. Press [MODE] to move to the next digit.
3. When you are satisfied with the number, press [MODE] until “OK” is highlighted.
4. To save the new value, press [Y/+]. The value is saved, and the menu advances to
STEL Alarm.
STEL Alarm
Set the STEL Alarm as follows:
1. In the STEL Alarm submenu, press [Y/+] repeatedly to select a desired number.
Numbers increase from 0 to 9. Once 9 is reached, pressing [Y/+] again “wraps”
around back to 0.
2. Press [MODE] to move to the next digit.
3. When you are satisfied with the number, press [MODE] several times until “OK”
is highlighted.
24
ToxiRAE Pro PID User’s Guide
4. To save the new value, press [Y/+]. The value is saved, and the menu advances to
TWA Alarm.
TWA
Set the TWA Alarm as follows:
1. In the TWA Alarm submenu, press [Y/+] repeatedly to select a desired number.
Numbers increase from 0 to 9. Once 9 is reached, pressing [Y/+] again “wraps”
around back to 0.
2. Press [MODE] to move to the next digit.
3. When you are satisfied with the number, press [MODE] until “OK” is
highlighted.
4. To save the new value, press [Y/+]. The value is saved, and the menu advances to
Alarm Mode.
Alarm Mode
There are two selectable alarm types:
Auto Reset When an alarm is triggered and after the alarm condition is no
longer present, the alarm stops and resets by itself.
Latch When the alarm is triggered, it will not cease until you manually
turn it off.
The latched setting only controls alarms for High Alarm and Low
Alarm, not the STEL or TWA alarms.
25
ToxiRAE Pro PID User’s Guide
Important! If you program the ToxiRAE Pro PID so that no alarms are activated in an
alarm condition, you may put yourself or your workers at risk of being exposed to a
hazardous atmosphere and being unaware of it, as the indication of a dangerous condition
will be limited to the concentration shown in the display and the name of the type of
alarm flashing on the display.
Whenever the Man Down feature is on, the main screen displays a Man Down icon along the
top to indicate it is active:
26
ToxiRAE Pro PID User’s Guide
When the Man Down feature is on and there is no gas alarm, the ToxiRAE Pro PID senses that
it is motionless for the amount of time set in the “Motionless Time” parameter. If the
instrument is not moved during that time, then a pre-alarm is activated to alert the user, and
shows the “Are You OK?” screen. Pressing [Y/+] clears the alarm and returns the ToxiRAE
Pro PID to its normal operation. Pressing [MODE] sets it into Man Down Alarm (and if
wireless connectivity is enabled, a Man Down message is sent in real time to remote
observers). If neither key is pressed, then after the countdown, it goes into Man Down Alarm
(again sending a message to remote observers if wirelessly enabled).
Off/On
Motionless Time (time the instrument is motionless before initiating a pre-alarm)
Sensitivity (set to low, medium, or high to compensate for ambient vibration or motion)
Warning Time (countdown, in seconds, from pre-alarm to Man Down alarm)
When the Man Down alarm is activated, the buzzer sounds and LEDs flash continuously, and a
countdown begins.
If the ToxiRAE Pro PID’s user presses [Y/+] for “Yes” in response to the “Are You
OK?” question on the screen before the countdown reaches zero, the Man Down alarm
stops and the main reading screen is displayed.
If the person does not press [Y/+] for “Yes” in response to the “Are You OK?”
question on the screen before the countdown reaches zero, the Man Down alarm is
sounded and LEDs flash continuously.
If the person presses [MODE] during the countdown, answering the “Are You OK?”
question with “No,” the Man Down alarm starts.
If the ToxiRAE Pro PID’s wireless connectivity is enabled, a Man Down message is also sent to
remote observers.
If you want to cycle through the Alarm Setting submenus, press [MODE] instead of [Y/+].
27
ToxiRAE Pro PID User’s Guide
If you want to cycle through the Alarm Setting submenus, press [MODE] instead of
[Y/+].
11.5.4. Datalog
Clear Datalog
This operation erases all data stored in the datalog.
Press [Y/+] to clear the datalog. The display asks, “Are you sure?”
Press [Y/+] if you want to clear the datalog. When it has been cleared, the display
shows “Datalog Cleared!”
Press [MODE] if you do not want to clear the datalog.
Interval
Intervals are shown in seconds. The default value is 60 seconds. The maximum interval is
3600 seconds, and the minimum is 1 second.
1. Press [Y/+] repeatedly to select a desired number. Numbers increase from 0 to 9.
Once 9 is reached, pressing [Y/+] again “wraps” around back to 0.
2. Press [MODE] to advance to the next digit.
3. Repeat this process until the desired value is entered.
When you have completed your selections, press [MODE] repeatedly until “OK” is
highlighted.
Data Selection
Data Selection allows you to select which types of data are recorded and made available
when you download your datalog to a computer via ProRAE Studio II software.
You can choose any or all of four types of data (you must choose at least one):
28
ToxiRAE Pro PID User’s Guide
Minimum
Average
Maximum
Real Time
1. Press [MODE] to step from one option to the next. The highlighter indicates your
choice.
2. Press [Y/+] to toggle your selection on or off (the check box indicates “on” with
an “X”).
3. When you have completed your selections, press [MODE] repeatedly until “Exit”
is highlighted.
4. Press [Y/+] to save the changes and exit.
Datalog Type
The instrument has two datalog types:
Auto Collects datalog information when the instrument is sampling until the
datalog memory is full.
Manual Datalogging occurs only when you manually initiate datalogging (see
below for details).
When the instrument is set to Manual Datalog, you can turn datalogging on and off from
the main measurement display in the Normal Mode by pressing the [MODE] key three
times.
When you reach the screen that says “Start Datalog?” press [Y/+] to start it. You
see “Datalog Started,” confirming that datalogging is now on.
When you reach the screen that says “Stop Datalog?” press [Y/+] to stop it. You
see “Datalog Stopped,” confirming that datalogging is now off.
29
ToxiRAE Pro PID User’s Guide
Wireless
There are seven Wireless parameters:
Radio On/Off
PAN ID
Channel
Join Network
Interval
Off Network Alarm
Factory Reset
Note: Turning the radio off does not change any of the settings. They are
stored and ready for use the next time the wireless modem is turned on.
1. Choose an “On” or “Off” by pressing [MODE] until your choice is highlighted. (the dark
circle in the “radio button” indicates that an option has been selected).
2. Press [Y/+] to select it.
3. Press [MODE] repeatedly until “Exit” is highlighted.
4. Press [Y/+] to register your selection and exit.
PAN ID All units on a network must be programmed with the same Pan ID (Personal
Network Identifier) to ensure communication compatibility.
Important! The allowed range for Pan ID numbers is 001 through 999.
1. Press [Y/+] and the display shows the current PAN ID. Example: “866.” The left-most
digit is highlighted.
2. Press [Y/+] repeatedly to select a desired number. Once 9 is reached, pressing [Y/+]
again “wraps” around back to 0.
3. Press [MODE] to advance to the next digit.
Repeat this process until all eight characters of the new PAN ID are entered.
To save your new PAN ID and exit, press [MODE] repeatedly until “OK” is highlighted.
Then press [Y/+]. It says, “Applying settings…” and then “Settings applied successfully!” to
indicate they have been registered. The menu now advances automatically to “Channel.”
30
ToxiRAE Pro PID User’s Guide
Channel Every network operates on its own channel, between 01 and 10 (do not use
00). If you need to know the network’s channel, check the EchoView Host’s
setting. Note: In Europe, only Channel 00 can be used, and it is preset (it
cannot be changed).
1. Press [Y/+] and the display shows the current Channel. Example: “10.” The left-most
digit is highlighted.
2. Press [Y/+] repeatedly to select a desired number. Once 9 is reached, pressing [Y/+]
again “wraps” around back to 0.
3. Press [MODE] to advance to the next digit.
Repeat this process until all eight characters of the new Channel are entered.
To save your new Channel number and exit, press [MODE] repeatedly until “OK” is
highlighted. Then press [Y/+]. It says, “Applying settings…” and then “Settings applied
successfully!” to indicate they have been registered. The menu now advances automatically
to “Join Network.”
Join Network This screen is for joining an existing network. When you see this screen,
press [Y/+] to join, or [MODE] to exit without joining.
While searching for the network, the message “Joining network…” is displayed.
If the network is found and successfully joined, then “Join network successful!” is displayed.
Press [MODE] to acknowledge the connection and return to the Wireless menu.
If the network is not joined, the display shows: “Join network failed!” You have two options:
Exit and Retry. If you want to retry, check that your network setting is correct (matches the
EchoView Host) and that the EchoView Host is turned on and operating. Then press [Y/+] to
retry.
Interval This sets the amount of time between data transmissions to the EchoView
Host.
1. Press [MODE] to step from one option to the other. The highlighted option changes each
time you press [MODE].
2. Press [Y/+] to make your selection (the dark circle in the “radio button” indicates the
option has been selected).
3. When you have completed your selection, press [MODE] repeatedly until “Exit” is
highlighted.
4. Press [Y/+] to save your selection, exit the Interval menu, and advance to “Off Netwk
Alarm.”
Off Netwk Alarm When this is enabled, the unit goes into alarm whenever an active network
connection is lost. This informs you that connectivity has been broken
between the ToxiRAE Pro and the EchoView Host.
31
ToxiRAE Pro PID User’s Guide
1. Choose “On” or “Off” by pressing [MODE] until your choice is highlighted. (the dark
circle in the “radio button” indicates that an option has been selected).
2. Press [Y/+] to select it.
3. Press [MODE] repeatedly until “Exit” is highlighted.
4. Press [Y/+] to register your selection and exit.
Factory Reset Selecting this resets the wireless settings to their original factory
configurations.
CAUTION! A factory reset of the wireless settings deletes any customized settings and
cannot be undone.
1. Press [Y/+] to select “Factory Reset.” You will see the message “Reset wireless
settings?”
2. Press [Y/+] for “Yes” or [MODE] for “Exit.” If you select “Exit,” the ToxiRAE Pro exits
without performing a factory reset.
Site ID
Choose and enter an 8-digit alphanumeric Site ID to uniquely identify the particular site where
the instrument is to be used. This Site ID is included in the datalog report.
1. Press [Y/+] and the display shows the current Site ID. Example: “SITE0001.” The left-
most digit is highlighted.
2. Press [Y/+] repeatedly to select a desired character. Letters increase from current value to
Z followed by digits from 0 to 9. Once 9 is reached, pressing [Y/+] again “wraps” around
to the letter A. For the last four characters that must be numerical, numbers increase from
0 to 9. Once 9 is reached, pressing [Y/+] again “wraps” around back to 0.
Note: The last four characters must be numerals.
3. Press [MODE] to advance to the next character.
Repeat this process until all eight characters of the new Site ID are entered.
To save your new Site ID and exit, press [MODE] repeatedly until “OK” is highlighted. Then
press [Y/+].
User ID
Enter an 8-digit alphanumeric User ID to uniquely identify a user. This User ID is
included in the datalog report.
32
ToxiRAE Pro PID User’s Guide
1. Press [Y/+] and the display shows the current User ID. Example: “USER0000.”
The left-most character is highlighted.
2. Press [Y/+] repeatedly to select a desired character. Letters increase from current
value to Z followed by digits from 0 to 9. Once 9 is reached, pressing [Y/+] again
“wraps” around to the letter A.
3. Press [MODE] to advance to the next character.
Repeat this process until all eight characters of the new User ID are entered.
To save your new User ID and exit, press [MODE] repeatedly until “OK” is highlighted.
Then press [Y/+].
User Mode
The ToxiRAE Pro PID has two user modes:
Basic Basic users can only see and use a basic set of functions.
Advanced Advanced users can see all screens and take advantage of all available
functions.
1. Press [MODE] to step from one option to the other. The highlighting changes
each time you press [MODE].
2. Press [Y/+] to make your selection (the dark circle in the “radio button” indicates
the option has been selected).
3. When you have completed your selection, press [MODE] repeatedly until “Exit”
is highlighted.
4. Press [Y/+] to register your selection, exit the User Mode submenu and advance
to Date.
Date
The Date is expressed as Month/Day/Year, with two digits for each (MM/DD/YY).
The left-most digit is highlighted to indicate it is selected when you enter the Date
submenu.
1. Press [Y/+] repeatedly to select a desired number. Numbers increase from 0 to 9.
Once 9 is reached, pressing [Y/+] again “wraps” around back to 0.
2. Press [MODE] to advance to the next digit.
Repeat this process until all six digits of the new date are entered.
3. Press [MODE] repeatedly until “OK” is highlighted.
33
ToxiRAE Pro PID User’s Guide
Note: If you do not want to save the change, press [MODE] repeatedly until
“Cancel” is highlighted. Press [Y/+] to exit to Time without saving the changes.
Time
The Time is expressed as Hours/Minutes/Seconds, with two digits for each. The time is in
24-hour (military) format of HH:MM:SS.
Note: If you do not want to save the change, press [MODE] until “Cancel” is
highlighted. Press [Y/+] to exit to Temp. Unit without saving the changes.
Temp. Unit
The display unit of the internal temperature sensor can be switched between Fahrenheit
and Celsius.
1. Press [MODE] to step from one option to the other. The highlighted option
changes each time you press [MODE].
2. Press [Y/+] to make your selection (the dark circle in the “radio button” indicates
the option has been selected).
3. When you have completed your selection, press [MODE] repeatedly until “Exit”
is highlighted.
4. Press [Y/+] to save your selection, exit the Temp. Unit menu, and advance to
Language.
Language
English is the default language, but other languages can also be selected for the
instrument.
1. Press [MODE] to step from one option to the next. The highlighted option
changes each time you press [MODE].
2. Press [Y/+] to make your selection (the dark circle in the “radio button” indicates
this option has been selected).
34
ToxiRAE Pro PID User’s Guide
3. When you have completed your selection, press [MODE] repeatedly until “Exit”
is highlighted.
4. Press [Y/+] to save your selection, exit the Language submenu, and advance to
Zero At Start.
Zero At Start
When Zero At Start is turned on, the instrument starts with a zero calibration every time
it is turned on.
LCD Contrast
The display’s contrast can be increased or decreased from its default setting. You may
not need to ever change the default setting, but sometimes you can optimize the display to
suit extreme temperature and ambient brightness/darkness conditions.
1. Press and hold [Y/+] to select a desired level of contrast. The range is 1 to 100.
Once 100 is reached, pressing [Y/+] again "wraps" around back to 1.
2. When you have completed your selection, press [MODE] repeatedly until “OK” is
highlighted.
3. Press [Y/+] to save your selection, and exit the LCD Contrast.
Note: If you do not want to save the change, press [MODE] repeatedly until
“Cancel” is highlighted. Press [Y/+] to exit without saving the changes.
35
ToxiRAE Pro PID User’s Guide
If Policy Enforcement is enabled and if the instrument has been bump tested and
calibrated in compliance with the policy settings, a check-mark icon is included along the
top of the ToxiRAE Pro PID screen:
If Policy Enforcement is enabled, then after startup the ToxiRAE Pro PID displays a
screen that informs the user that the instrument requires either a bump test or a
calibration. If both are required, then they are shown in sequence.
To program a ToxiRAE Pro PID via an AutoRAE 2 Cradle, you need ProRAE Studio II
Instrument Configuration and Data Management Software, the AutoRAE 2 Cradle
connected to a power source, and a USB PC communications cable.
1. Connect a USB cable between a PC with ProRAE Studio II and the AutoRAE 2
Cradle.
2. Apply power to the AutoRAE 2 Cradle.
3. Turn off the ToxiRAE Pro PID (or put the ToxiRAE Pro PID into PC
Communications Mode) and set it in the cradle.
4. Start ProRAE Studio II software on the PC.
5. Select “Administrator” and input the password (the default is “rae”).
6. Click “Detect the instruments automatically” (the magnifying glass icon with the
letter “A” in it). After a few seconds, the AutoRAE 2 Cradle is found and it is shown,
along with its serial number:
36
ToxiRAE Pro PID User’s Guide
37
ToxiRAE Pro PID User’s Guide
8. In ProRAE Studio II, the AutoRAE 2 Cradle is shown, including its Serial Number,
under “Online”:
9. Expand the view to show the ToxiRAE Pro PID in the AutoRAE 2 Cradle by clicking
the “+” to the left of the image of the AutoRAE 2 Cradle:
38
ToxiRAE Pro PID User’s Guide
12. In the menu that now appears on the left side, click “Policy Enforcement.” It is
highlighted, and the Policy Enforcement pane is shown:
For “Must Calibrate” and “Must Bump,” you have the options of no enforcement or
enforcement (including “Can’t Bypass,” and “Can Bypass”).
Must Calibrate. The user is prompted to calibrate the instrument when calibration is due
(as set by the calibration interval). There are two programmable options:
Must Bump
Can’t Bypass. Unless a bump test is performed, the instrument cannot be used,
and the only option is to turn off the instrument.
Can Bypass. If a bump test is due but the user does not want to perform one, the
instrument can still be used.
39
ToxiRAE Pro PID User’s Guide
These are the screens that are shown on a ToxiRAE Pro PID after startup if “Can Bypass”
is selected:
If “Can’t Bypass” is selected, the display looks like this, and only allows the options of
performing the test or shutting down:
40
ToxiRAE Pro PID User’s Guide
You can select “Must Calibrate” and/or “Must Bump” and then set whether the user
must perform the selected operation in order to use the instrument.
15. Once you have made your selections in ProRAE Studio II, you must upload the
changes to the instrument. Click the icon labeled “Upload all settings to the
instrument.”
16. A confirmation screen is shown. Click “Yes” to perform the upload, or “No” to abort.
Uploading takes a few seconds, and this progress bar is shown. You can abort the
upload by clicking “Cancel.”
41
ToxiRAE Pro PID User’s Guide
If the ToxiRAE Pro PID screen displays the message that it must be bump tested or
calibrated, and if the option to bypass bump testing or calibration is not available, you
should shut off the instrument and follow the procedure outlined here if you want to
change the Policy Enforcement settings:
1. Use a USB cable to connect the ToxiRAE Pro PID in its Travel Charger or Desktop
Cradle to a computer running ProRAE Studio II.
2. Enter Diagnostic Mode on the ToxiRAE Pro PID (with the instrument turned off,
press and hold [Y/+] and [MODE] until it starts up.
3. After startup, enter the password when prompted (default is “0000”) and press
[MODE].
4. Press [MODE] repeatedly until you see the “Enter Communications Mode?” screen.
5. Press [Y/+] to enter Communications Mode.
6. Start ProRAE Studio II.
7. Select “Administrator.”
8. Input the password (the default is “rae”).
9. Click “OK.”
10. Click “A” (detect instruments automatically).
11. Click on the instrument’s icon when it appears.
12. Click “Select.”
13. Click “Setup.”
14. Click “Policy Enforcement.” The Policy Enforcement pane is shown.
15. Deselect Policy Enforcement features you do not wish to use.
16. Click “Upload all settings to the instrument.”
42
ToxiRAE Pro PID User’s Guide
Uploading will take a few seconds, and this progress bar is shown:
43
ToxiRAE Pro PID User’s Guide
1. Connect the calibration gas cylinder, flow regulator, and calibration adapter to the
ToxiRAE Pro PID and start the gas flow.
2. Make sure the unit goes into alarm and that the buzzer produces at least two beeps per
second, the LED lights flash on and off, and the vibration alarm functions. The
display backlight should illuminate and an alarm message should be shown in the
display.
3. Turn off the gas flow.
4. Remove the calibration adapter.
Note: Bump testing and calibration can also be performed by using the RAE Systems
AutoRAE 2 Automatic Test And Calibration Station. Refer to the AutoRAE 2 User’s
Guide for instructions.
1. Place the Calibration Adapter on the top cap of the ToxiRAE Pro PID by pressing
it into place.
2. Attach the hose from the regulator/calibration gas cylinder to the Calibration
Adapter’s inlet.
44
ToxiRAE Pro PID User’s Guide
After calibrating the ToxiRAE Pro PID, you must remove the Calibration Adapter by
lifting it off the ToxiRAE Pro PID.
Note: If you use a zero air cylinder, you must use the ToxiRAE Pro PID Calibration
Adapter. Using a calibration adapter is not necessary for calibration in fresh air.
Turn on the ToxiRAE Pro PID. Once it has been through its startup, enter Programming
Mode:
1. Press and hold [MODE] and [Y/+] until you see the Password screen.
45
ToxiRAE Pro PID User’s Guide
If you make a mistake, you can cycle through the digits by pressing [MODE] and
then using [Y/+] to change the number in each position.
If you do not know the password, do not enter anything. Just press [MODE]
repeatedly to highlight OK, and then press [Y/+].
Note: If the ToxiRAE Pro PID is in Programming Mode and you do not press a key
within 60 seconds, it exits Programming Mode and re-enters Normal Mode.
Note: You can abort the zero calibration during its countdown by pressing the [MODE] key.
Important! If you used the Calibration Adapter and a zero air cylinder, you must remove
the Calibration Adapter from the ToxiRAE Pro PID. If the Calibration Adapter is
attached during normal operation, inconsistent and lower-than-normal readings will occur
because of decreased concentration of the gas being monitored.
To begin calibration, connect the calibration gas cylinder, flow regulator, and calibration
adapter to the ToxiRAE Pro PID.
With the ToxiRAE Pro PID in Programming Mode, and with Span Calib highlighted,
follow this procedure:
1. Press [Y/+]. The screen displays the current (or default) calibration gas and its
concentration. For example:
46
ToxiRAE Pro PID User’s Guide
If you entered the Calibration Menu without supplying the correct password, or
supplied the correct password but chose not to change the Cal.Gas, you will see a
message like this:
Cal.Gas: Isobutylene
Span=100ppm
Apply gas…
During calibration, the calibration gas name, its concentration, and the countdown are
displayed. Depending upon the device alarm settings, the monitor may go into low and
then high alarm once span calibration is complete, which is expected in response to the
test gas.
Note: You can abort span calibration during its countdown by pressing [MODE].
Upon completion, the screen “Span is done!” appears along with the reading (it should be
within 10% of the span gas concentration).
Important! After calibration is complete, you must remove the Calibration Adapter from
the ToxiRAE Pro PID. If the Calibration Adapter is attached during normal operation,
inconsistent and lower-than-normal readings will occur because of decreased
concentration of the gas being monitored.
If you selected “Change” for span gas concentration, the following screen appears:
47
ToxiRAE Pro PID User’s Guide
The ToxiRAE Pro PID’s Diagnostic Mode can only be accessed at startup time. In
Diagnostic Mode, ToxiRAE Pro PID displays readings in raw counts instead of units such as
parts per million (ppm).
Step from one position in the four-character string to the other by pressing
[MODE].
Press [Y/+] repeatedly to select a desired number. Numbers increase from 0 to
9.
Once 9 is reached, pressing [Y/+] again “wraps” around back to 0.
4. When you are done, press [MODE] until either OK or Cancel is selected. Press
[Y/+] to register the password (if “OK” is highlighted) or to exit without entering
the password (if “Cancel” is selected).
Note: The next time you start ToxiRAE Pro PID, hold only [MODE], and it will
automatically start in Normal Mode.
48
ToxiRAE Pro PID User’s Guide
The alarm priority is as follows (in the event of multiple simultaneous alarms):
Super Alarm > Man Down Alarm > Man Down Warning > Lamp > Fan > Max > Over >
High > Low > Neg > STEL > TWA > Cal Failed > Bump Failed > Cal Required > Bump
Required > Offline > Bat
49
ToxiRAE Pro PID User’s Guide
The ToxiRAE Pro PID must be connected to a PC through the supplied Charging / PC
Communications Cradle and must be in the PC communications mode.
1. Make sure the Charging/PC Communications Cradle has power from its AC
adapter (the LED on the front of the cradle should be illuminated).
2. Use the supplied PC Communications Cable (USB to mini-USB cable) to connect
the Cradle to a PC.
3. Turn on the ToxiRAE Pro PID. Make sure it is running in Normal mode (with the
main measurement screen with VOC reading showing).
4. Insert the ToxiRAE Pro PID in the cradle.
5. Activate the PC communications mode on the ToxiRAE Pro PID by pressing
[MODE] repeatedly, starting from the main measurement screen until you reach
the “Enter Communications Mode and stop measurement?” screen.
6. Press [Y/+]. Measurement and datalogging stop, and the instrument is now ready
to communicate with the PC. The display now says “PC comm ready…”
7. Start up the ProRAE Studio II software, enter a password, and detect the
instrument following the directions provided in the ProRAE Studio II User’s
Manual.
8. Follow the instructions in the ProRAE Studio II User’s Manual to download the
datalog, configure the instrument settings, or update the ToxiRAE Pro PID’s
firmware.
9. When you are done, press [MODE] to exit the PC communications mode on the
ToxiRAE Pro PID. The screen displays “Sensor initializing,” after which the
instrument returns to operating in Normal mode.
50
ToxiRAE Pro PID User’s Guide
17. Maintenance
WARNING!
Maintenance should be performed only by a qualified person who has proper
training and fully understands the contents of this manual.
WARNING
To reduce the risk of ignition of hazardous atmospheres, replace the battery only in
areas known to be non-hazardous.
1. If the rubber boot is on the ToxiRAE Pro PID, remove it (refer to page 55 for details).
2. Place the ToxiRAE Pro PID face-down on a soft surface.
3. Use a Philips screwdriver to loosen the screw holding the top cap in place, and then
carefully use the provided tool to pry up the top cap from the middle in the front and
back and use your fingers to remove the top cap.
51
ToxiRAE Pro PID User’s Guide
4. Remove the four screws on the back of the instrument by turning them counterclockwise.
5. Hold the ToxiRAE Pro PID down and separate the rear cover from the front by
pulling from the top and tilting it open without disconnecting the ribbon cable
connecting the two halves.
Ribbon cable
6. Carefully disconnect the battery from the battery connectors on the circuit board
by pulling it toward the bottom of the instrument. Be careful not to damage the
ribbon cable.
52
ToxiRAE Pro PID User’s Guide
7. Before installing a new battery, visually inspect the contact pins on the ToxiRAE
Pro PID circuit board to make sure they are not bent. If they are, carefully
straighten them before installing the battery. Install the new battery (part number
G02-3004-000), making sure it is inserted fully. Make sure the battery connectors
on the circuit board go all the way into the connector slots in the battery.
8. Inspect to make sure the ribbon connector is still connected, and plug it back in if
it has come unplugged.
9. Place the cover over the compartment by tilting it up and then fitting it in place.
10. Tighten all four screws by turning them clockwise with a torque-limiting
screwdriver (preferably an electric one). Tighten them in the numerical order
shown here, to a torque rating of 3.54 to 4.43 lbf-in (4.08 to 5.10 kgf-cm).
53
ToxiRAE Pro PID User’s Guide
11. Replace the top cap and tighten the Philips screw.
Important! Charge the battery completely before using the ToxiRAE Pro PID, and
check the calibration before placing the instrument in service.
At the end of its life, this product must undergo separate collection and recycling from
general or household waste. Please use the return and collection system available in your
country for the disposal of this product.
54
ToxiRAE Pro PID User’s Guide
1. Flip up the tab on the belt clip on the rear of the instrument.
2. Remove the Philips screw that holds the clip in place.
3. Stretch the bottom corners of the boot and gently slide the bottom of the boot over
the rear of the ToxiRAE Pro PID.
4. Slide the boot up until it comes off of the instrument. Make sure that you do not
force it to move if it sticks against the top cap. Gently nudge it.
5. Inspect the rubber boot for damage, and replace it if it is cracked or torn.
When replacing the boot, simply reverse the procedure, sliding the boot onto the
instrument and then carefully stretching it over the bottom portion of the instrument. Do
not forget to replace the belt clip.
55
ToxiRAE Pro PID User’s Guide
1. Remove the top cap. First remove the small Phillips screw on the back side:
2. Then use the special tool (part number G02-0306-003, package of three) and
apply leverage at the middle of the instrument to push the top cap loose, and then
remove it with your fingers.
56
ToxiRAE Pro PID User’s Guide
3. Once the top cap is removed, install the new top cap assembly.
4. Place the new rubber insert onto the ToxiRAE Pro PID, being careful to align the
insert correctly and that it is not distorted. Also, make sure that you do not press
on the fan.
5. Press the new top cap onto the ToxiRAE Pro until it is fully seated. Check to see
that the pin on the front side of the cap went into the corresponding groove on the
front side of the instrument housing. Then tighten the Phillips screw.
57
ToxiRAE Pro PID User’s Guide
1. Gently lift out the PID module with your fingers, being careful not to damage the
fan:
2. If the module requires replacement (because the lamp does not illuminate, or the
module has been used past its expiration date), place a new module into the slot,
being careful to match the indexing keys. The sensor can only go into its slot one
way. Refer to step 11 for alignment information.
3. If you want to open the sensor module to inspect and clean the lamp and sensor
electrode panel, you must use the special tool. The special tool’s “C”-shaped end
has small “teeth” inside. Slide the tool so that the teeth slip into the notch between
the module’s cap and body:
58
ToxiRAE Pro PID User’s Guide
7. Clean the sensor electrode panel in a solution of methanol lamp cleaner (included,
along with cleaning swabs, in a PID Lamp Cleaning Kit, part number 500-0014-
010, package of 10), and allow it to dry.
8. Clean the lamp’s window with a cleaning swab dipped in methanol lamp cleaner,
and allow it to dry. Do not touch the lamp window with your fingers, as the
residual oils will shorten its life.
9. Inspect the electrical contacts. Clean them with a swab dipped in lamp cleaner if
they appear to need cleaning:
59
ToxiRAE Pro PID User’s Guide
10. Reassemble the sensor module by placing the sensor electrode panel back in place
and firmly pressing the cap back onto the top.
11. Place the sensor module back into the ToxiRAE Pro PID. Make sure the index
points are aligned (it can only go in one way).
Match index
points on sensor
module with
ToxiRAE Pro PID
12. Carefully place the cap back onto the ToxiRAE Pro PID and tighten the screw.
Note: Always calibrate the ToxiRAE Pro PID after replacing the sensor module.
60
ToxiRAE Pro PID User’s Guide
3. Inspect the new fan and make sure its two electrical pins are straight.
4. Align the fan so that the indexing key (the raised rectangular portion) on its body
matches with the keyway in the slot and the electrical pins and carefully slide into
the contact points at the bottom of the slot.
Important! If you encounter resistance while pressing the new fan into the slot,
remove it and check that the electrical pins are not bent and that all alignment is
correct before inserting the fan again.
Indexing key
Electrical pins
5. Gently press the fan into place to make sure it is completely seated.
61
ToxiRAE Pro PID User’s Guide
Visually inspect the contacts at the base of the ToxiRAE Pro PID and on the charging
cradle to make sure they are clean. If they are not, wipe them with a soft, dry cloth. Never
use solvents or cleaners.
http://www.raesystems.com
62
ToxiRAE Pro PID User’s Guide
18. Troubleshooting
63
ToxiRAE Pro PID User’s Guide
E-mail: [email protected]
Web Site: www.raesystems.com
64
ToxiRAE Pro PID User’s Guide
RAE BeNeLux BV
Hoofdweg 34C
2908 LC Capelle a/d IJssel
The Netherlands
Phone: +31 10 4426149
Fax: +31 10 4426148
Email: [email protected]
Web: www.rae.nl
65
ToxiRAE Pro PID User’s Guide
66
ToxiRAE Pro PID User’s Guide
SAFETY INSTRUCTIONS
Read Before Operating
This manual must be carefully read by all individuals who have or will have the
responsibility of using, maintaining, or servicing this product. The product will perform
as designed only if it is used, maintained, and serviced in accordance with the
manufacturer’s instructions. The user should understand how to set the correct parameters
and interpret the obtained results.
CAUTION!
Only use RAE Systems battery pack P/N: G02-3004-000
Do only charge the battery pack using RAE Systems charger outside hazardous area.
Use of non-RAE Systems components will void the warranty and can compromise the
safe performance of this product.
Warning: Substitution of components may impair intrinsic safety.
67
ToxiRAE Pro PID User’s Guide
For North America and Canada the equipment can further be used in Class I, Zone 0.
Do only charge the battery pack using RAE Systems charger outside hazardous area
(Um: 20V).
The appropriate regulations for service and repair must be properly observed during such
activities.
68
ToxiRAE Pro PID User’s Guide
Year of manufacture
To identify the year of manufacture, refer to the serial number of the instrument.
The second to last digit in the serial number indicates the year of manufacture. For
example, “M” indicates the manufacturing year is 2010.
69
RAE Systems
World Headquarters
3775 N. First St.
San Jose, CA 95134-1708 USA
Phone: 408.952.8200
Fax: 408.952.8480
E-mail: [email protected]
Web Site: www.raesystems.com