Professional Documents
Culture Documents
Tormeck 2000 Supergrind System Handbook and MANUAL - 000005972
Tormeck 2000 Supergrind System Handbook and MANUAL - 000005972
3
©
This handbook is copyright and no part of it may be reproduced
without express written consent by
TORMEK AB
Box 152
S-711 23 Lindesberg
Sweden
4
Acknowledgement
I should like to thank the TORMEK users around the world for their tips and advice in the
preparation of this handbook. The close contact with the many skilled craftsmen at exhibi-
tions and by correspondence has been most inspiring and beneficial in the development
of our water cooled grinding and sharpening system.
Torgny Jansson
5
Fourth edition
This edition is entirely revised as considerable developments in the TORMEK system
have been introduced.
A Horizontal Base for the Universal Support has been developed which permits grinding
away from the edge. This is especially advantageous for grinding and sharpening wood-
carving or woodturning tools. A profiled leather honing wheel has been developed for the
inside honing of gouges and V tools.
The latest developments are the Pro AngleMaster WM-200 and the Multi Jig SVS-50. The
Pro AngleMaster WM-200 can be set at any angle and works on any stone diameter. The
Multi Jig SVS-50 is especially developed for oval skew chisels. It is also suitable for
roughing gouges, wide carving gouges and parting tools. This jig replaces the SVS-40 jig.
There is now a detailed instruction on how to grind, sharpen and hone carving gouges
and V tools in the SVD-180 jig.
The function of a burr on turning scrapers and ticketing of the edge is covered.
The chapter The basics of grinding, sharpening and honing of edge tools, has been
completed with the sections Edge angles and bevel angles, Vertical and horizontal
grinders, Hollow bevels, Grinding pressure and Tool rests and grinding jigs.
At the end of the book there is a summary of the recommended way to grind various tools.
The number of pages is increased from 78 to 129 and the number of line drawings from
180 to 450.
Fifth edition
In this edition, the chapter dealing with the grinding, re-sharpening and honing of turning
gouges in the SVD-180 jig is revised. The factors determining the shape of a fingernail
bowl gouge are explained and there is a graph survey showing various shapes. There is
also detailed advice on how you set the jig at re-sharpenings in the easiest way.
Furthermore the mounting of mitre guillotine blades in the SVH-320 jig is described.
The number of line drawings is increased from 450 to 468 and the number of pages is
increased from 129 to 137.
Sixth edition
This edition includes the new Short Tool Jig SVS-32, which has been developed primarily
for palm held woodcarving tools and tools for power carvers. The general instructions for
carving gouges and carving V tools have been revised and put in separate chapter,
Grinding techniques for carving gouges and V tools.
The 2000 series housing now has a new design and there is a scale on the machine label
showing the stone diameter.
The grinding and ticketing of cabinet scrapers are covered in the chapter on the SVD-110
Tool Rest.
The cover is amended. The number of line drawings is increased to 502 and the number
of pages to 147.
6
Contents
Contents
The basics of grinding, sharpening and honing edge tools ...........................9
Grinding and sharpening ..................................................................................10
Edge angle and bevel angle .............................................................................11
Dry grinding and wet grinding...........................................................................12
Vertical and horizontal grinders .......................................................................13
Hollow bevel ....................................................................................................14
Grinding direction .............................................................................................15
Grinding pressure .............................................................................................16
Tool rests and grinding jigs...............................................................................18
Honing ..............................................................................................................19
Grinding techniques for carving gouges and V tools ........................................20
Instructions ........................................................................................................33
Safety ...............................................................................................................34
Preparation before grinding ..............................................................................36
The Universal Support......................................................................................37
Setting the edge angle .....................................................................................38
Pro AngleMaster, WM-200 ...............................................................................40
Straight Edge Jig, SVH-60................................................................................44
Planer/Jointer Blade Jig, SVH-320 ..................................................................50
Universal Gouge Jig, SVD-180.........................................................................55
Multi Jig, SVS-50 ..............................................................................................78
Short Tool Jig, SVS-32 .....................................................................................94
Tool Rest, SVD-110........................................................................................101
Axe Jig, SVA-170 ...........................................................................................106
Knife Jig, SVM-45...........................................................................................108
Long Knife Jig, SVM-100................................................................................115
Scissors Jig, SVX-150 ....................................................................................116
Grinding without jigs .......................................................................................119
Diamond Truing Tool, ADV-50D.....................................................................120
Stone Grader, SP-650 ....................................................................................122
Honing and polishing ......................................................................................124
7
Contents
8
The basics of grinding,
sharpening and honing
edge tools
9
The basics of grinding, sharpening and honing edge tools.
Here is shown, enlarged, the various stages of a knife edge (scale 10:1).
In principle, this is the case for all edge tools.
A sharp edge. The edge is worn and blunt. After honing on a bench stone
the edge is sharp again, but with
an increased edge angle.
After another period of use the Another honing sharpens the The edge is now re-ground to its
edge is blunt again. edge to a still larger angle. original shape.
Grinding means that so much steel is removed from the tool that the edge is restored to
the original angle or altered on purpose to a new angle. The shape of the tool can also
be changed according to your requirements.
10
The basics of grinding, sharpening and honing edge tools.
On tools with the bevel on one On tools with symmetrical bevels On tools with an outer and an
side, the edge angle (a) is the on both sides, the edge angle inner bevel, the edge angle (a)
same as the bevel angle (b). (a) is twice the bevel angle (b). is the sum of the two bevel
angles (b1 and b2).
The size of the edge angle is critical for the efficient functioning of the tool. The edge
angle should be as narrow as possible without being too weak to withstand the stresses
when working with the wood. The optimal edge angle for each tool is a compromise
between the need for the tool to cut as easily as possible and stay sharp as long as possi-
ble. A basic requirement is that the edge is strong enough to do the work without being
damaged or bent.
A specific tool can be ground at various edge angles depending on how it is to be used.
You can of course also have more than one tool of the same type and grind them with
various edge angles – each optimal for its application.
Recommendations for edge angles are given with the grinding instructions for each tool.
With the TORMEK Pro AngleMaster you can set the desired edge angle before you start
grinding. You can also measure the existing edge angle on a tool. Please see the chapter
WM-200.
Denominations
In the literature on this subject, there are various denominations for the edge angle. It is
called bevel angle, cutting angle or sharpening angle.
The edge angle on a tool with bevels on both sides is called the included bevel angle,
the effective bevel angle, profile angle, total cutting angle or the combined bevel
angle.
11
The basics of grinding, sharpening and honing edge tools.
Also the length of the bevel is sometimes used to express the size of the edge angle.
Then the bevel length must be related to the thickness of the tool as a thicker tool has a
longer bevel than a thinner tool – both with the same edge angle.
By consistently using the denominations edge angle and bevel angle as explained
above, you know what we mean and this avoids further explanation and confusion.
Dry grinding
Bench grinders and belt grinders have a high cutting ability and they grind quickly. Bench
grinders have the grinding wheel mounted directly on the motor shaft, thus the grinding
wheel runs with the same speed as the motor (usually 2 850 rpm at 50 Hz and 3 400 rpm
at 60 Hz). As there is no reduction gear between the motor and the grinding wheel, bench
grinders are comparatively cheap. The belt on a belt grinder also runs with the same high
rpm as its motor.
A disadvantage of high-speed grinders is that the tool edge is heated up by the friction,
with the risk that the temper is drawn from the steel. The edge then loses its hardness and
the tool soon needs to be ground again.
You can reduce the risk of overheating by regularly placing the tool in water during the
grinding. However, it is very difficult to prevent the extreme edge from becoming too hot
as it is very thin and very sensitive to heat. It is very easy to reach 230° - 240°C which is
the annealing temperature for carbon steel. If the tip is overheated, the tool has to be re-
ground (without overheating!) until you reach material which has not been affected by the
heat.
This is the case not only for hardened carbon steel and stainless steel, but also for high
speed steel (HSS), although the margins for overheating here are larger.
When grinding with a bench grinder, sparks occur and you need either protection goggles
or a face-guard. Alternatively, the machine must be equipped with transparent protection
shields. Because of the high RPM the wheels must have guards, which cover fl of the cir-
cumference. This limits the accessability during some grinding operations.
When dry grinding, the surface of the bevel becomes rather rough and it needs to be
smoothed with a fine grain honing stone.
Wet grinding
When grinding on a water cooled grindstone, the stone runs in a bath of water. The stone
carries the water continuously to the grinding surface, thus cooling it and eliminating the
risk of overheating.
12
The basics of grinding, sharpening and honing edge tools.
The grindstone runs between 50-130 rpm, depending on its diameter. A larger grindstone
runs with a lower axle speed than a small one. The low peripheral speed ensures that the
water is not thrown off by the centrifugal force.
The reduction of the high rpm of the motor (you cannot run a standard electric motor at a
low rpm) can be achieved with a worm gear, gear belts or with a friction gear. Since you
need a reduction gear, wet grinders are more expensive than bench grinders, which do
not have a reduction gear.
It is desirable to be able to lower and remove the water trough for cleaning. Particles from
the steel and the stone will form a hard mass unless they are cleaned away regularly.
The surface finish after wet grinding is finer than with dry grinding. Often honing is not
required after grinding.
The grinding operation on a wet grindstone is easy to control, as the stone runs slowly
and the risk of accidents is minimal due to the low rpm. The wet grindstone does not pro-
duce sparks, which means that it can be operated in areas of high fire risk such as wood
working shops. There is also no risk of the stone shattering and injuring people.
Wet grindstones were originally natural sandstone and gave a very finely ground surface.
In recent years man-made stones have been developed. These are ceramically made and
have abrasives of aluminum-oxide. Man-made stones grind much faster and usually have
a coarser grinding surface.
Although the grinding time itself is longer on wet grinders compared to bench grinders, the
total time for grinding and honing of a tool is much shorter. This is because the need for
honing after grinding is greatly reduced or eliminated.
Since wet grinding has obvious advantages compared to dry grinding, the TORMEK
grinding system is designed on this method.
13
The basics of grinding, sharpening and honing edge tools.
Hollow bevel
When grinding on a vertical grindstone the bevel has a
slightly hollow shape due to the radius of the grindstone
– the smaller the diameter of the wheel, the larger hollow
grinding.
When you make a line drawing to explain the hollow bevel,
you need to exaggerate the effect to be able to show it.
This creates a wrong impression about the real size of the
hollow.
The hollow shape from a 250 mm (10") grindstone is Hollow grinding. Exaggerated.
minimal. When grinding a tool of 2 mm thickness (5/64") with
a 20° edge angle the hollow is as small as 0,03 mm
(0,0012"), which is hardly noticeable and has no practical
influence on the function of the tool.
0,03 mm (0,0012")
20°
2 mm
5/64"
Ø 250 mm (10")
Ten times enlargement of a 2 mm thick tool ground with a 20° edge angle. In spite of the enlarged
scale the hollow is hardly noticeable. It is only 0,03 mm or 0,0012".
14
The basics of grinding, sharpening and honing edge tools.
Grinding direction
The question whether to grind away from or towards the
edge is probably as old as the art of water-cooled grinding.
Many experienced and skilled craftsmen state that one
should grind away from the edge whilst others, equally
experienced, maintain that one should grind towards the
edge. Conventionally dry grinding at a high rpm is always
carried out towards the edge.
Our tests show no noticeable difference between the two
methods in relation to the sharpness of the edge. There are Grinding away from the edge.
however some practical and essential differences in the
grinding operations.
You achieve a higher grinding pressure and thus faster
grinding when grinding towards the edge as the rotation of
the grindstone helps to press the tool towards the stone.
When grinding away from the edge the grindstone tends to
lift the tool and decrease the grinding pressure.
Grinding towards the edge tends to activate the grindstone
and reduce the risk of a glazed stone surface. The burr
developed during grinding is shorter and stiffer compared to Grinding towards the edge.
grinding away from the edge, when it is longer and thinner.
A disadvantage when grinding towards the edge, is the
risk that the tool can accidentally dig into the stone. This
can be eliminated if the tool is mounted in a grinding jig.
Vibration can also occur at steeper edge angles, which is
not the case when grinding away from the edge.
Grinding away from the edge is preferable when you need
a light grinding pressure, e.g. when grinding small and deli-
cate woodcarving tools. In this direction you can easily con-
trol the grinding operation and observe the burr developing Grinding towards the edge
as no water flows over the edge. increases the grinding pressure
Free-hand grinding is best done with the stone running
away from the edge.
With the TORMEK system you can grind both towards and
away from the edge. In the chapter Grinding methods
there is a recommendation of the grinding direction for vari-
ous types of tool.
It should be noted that this question of grinding away from
or towards the edge must not be mixed up with the ques-
tion whether the grindstone should rotate away from you or
Grinding away from the edge
towards you. This depends on how you position the
decreases the grinding pres-
machine. The TORMEK machines can be positioned either sure.
way.
15
The basics of grinding, sharpening and honing edge tools.
Grinding pressure
Wet grinding
If during the grinding you apply a certain force with your hands on a tool, the grinding
pressure will vary depending on the area which is in contact with the grindstone. A smaller
contact area gives a larger grinding pressure. This is an important factor to be taken into
consideration, since this grinding pressure decides the grinding rate and the extent of
wear on the grindstone.
For example, if you push with the same force on a wide plane iron as on a narrow wood
chisel, the grinding pressure can be 10 times higher on the wood chisel. On a carving
gouge, which has a very small contact area on the grindstone, the grinding pressure can
be as much as 50 times higher.
The following examples illustrate how the grinding pressure varies on three typical tools
ground with a 25° edge angle. The force applied with your hands to each tool is 100 N or
approx. 10 kp (22 lbf).
100 N
22 lbf
Plane iron
Grinding area: 235 mm2
(0,36 in2)
Grinding pressure:0,43 N/mm2
(61 psi) 50 mm (2")
100 N
22 lbf
Wood chisel
Grinding area: 48 mm2
(0,074 in2)
Grinding pressure: 2,1 N/mm2
(302 psi) 6 mm (15/64")
100 N
22 lbf
Carving gouge
Grinding area: 4,7 mm2
(0,0078 in2)
Grinding pressure: 21 N/mm2
(3085 psi) »1 mm (3/64")
16
The basics of grinding, sharpening and honing edge tools.
As shown in these examples, you must ensure that you do not push too hard when grind-
ing small delicate tools, especially those with a curved edge. Otherwise the grinding pres-
sure will be too high, which could cause you to overgrind. The stone will also wear too
quickly and the tool will make grooves in the grindstone.
On the other hand, there is no limitation to the force you can apply when you utilise the
whole width of the stone, e.g. when grinding a wide plane iron or an electric planer blade.
When grinding hard HSS steel the stone needs a certain grinding pressure to replace old
and worn grains with new, fresh ones. Therefore when grinding electric planer blades,
which have a large grinding area, you should activate the stone with the Stone Grader
SP-650. Please see the chapter SP-650.
After some practice you will soon learn to control the grinding pressure and the optimal
grinding speed for each tool.
Dry grinding
High speed grinders removes steel faster and therefore you must ensure that you do not
overgrind the tool. Woodcarving tools are very sensitive to grinding as they have narrow
edge angles and are made of carbon steel.
Woodcarving tools should therefore not be ground on a high speed grinder – the risk of
overgrinding is too great and there is a big risk of drawing the hardening of the steel,
making it impossible to hold a sharp edge.
17
The basics of grinding, sharpening and honing edge tools.
On a conventional tool rest the pressure you When you push the tool towards the grindstone
apply to the tool mainly goes to the tool rest. to achieve the required grinding pressure, it
climbs up on the stone.
This effect appears when grinding narrow edge angles and when grinding both towards
and away from the edge. The disadvantage is more severe when grinding turning tools,
as they are often made of HSS-steel which is hard and requires a high grinding pressure.
For turning scrapers which are ground at larger edge angles, this type of tool rest works
satisfactorily on dry or water-cooled grinders.
18
The basics of grinding, sharpening and honing edge tools.
The reason that these types of tool rest work fairly well on high speed dry-grinders, is that
they require a lower grinding pressure and therefore the disadvantages can be overcome.
For water-cooled grinders, the tool rest or grinding jig should be designed so that you can
control the grinding pressure. This is achieved by mounting the tool in a jig, which is pivot-
ed around an axle positioned at a distance from the grindstone. The pressure which you
then apply to the tool is distributed to the grinding spot on the grindstone instead of the
tool rest. Furthermore, the tool is guaranteed to be in the same position on the grindstone,
which is necessary for achieving a precisely ground edge.
Honing
When grinding, a burr (or wire edge) develops on the upper side of the edge. This burr
must be honed off on a fine grit honing stone or slipstone. The honing also removes the
marks left by the grinding wheel which makes the surface finer. When the grinding is
made on a coarse grinding wheel, the surface requires more honing.
The honing stone must work on the entire bevel of the edge otherwise the tip will be
rounded off. The burr bends from side to side and therefore both sides of the edge need
to be honed alternately.
You can also power hone on a felt buffing wheel mounted on a bench grinder. However
there is here a great risk of rounding off the tip of the edge due to the aggressive honing
effect caused by the high speed. (usually 2 850 rpm at 50 Hz and 3 400 rpm at 60 Hz).
You must also pay attention so that you do not press the tool too hard towards the wheel
which could cause overheating of the edge.
With the TORMEK system you hone on leather honing wheels running at a low rpm. The
low speed enables you to control the operation and there is no risk of rounding off or over-
heating the edge.
The honing process is also controlled with jigs, so you get exactly the same edge angle
and movement pattern towards the wheel as during the previous sharpening.
19
The basics of grinding, sharpening and honing edge tools.
The grinding area on a gouge is The grinding area on a plane Over-grinding on a spot on a
almost as narrow as a line. iron is a rectangle. gouge means that the entire
edge must be re-shaped.
Firstly you should question whether you need to grind your tool or if you should only
hone it. This question is especially important when working with small and delicate tools
with a small edge angle. A slight over grinding on a spot on these tools makes a pro-
nounced pit or hollow on the contour of the edge.
The basic recommendation is therefore not to grind small and delicate tools, which have
become dull, but instead hone them on a bench stone or on a rotating honing wheel.
Grinding/sharpening on a grindstone is however required in the following cases:
• The edge has become too dull to be honed.
• You want to change the shape of the edge, e.g. the edge plane angle. Please see
following page).
• You want to change the edge angle.
• The edge has become damaged.
20
The basics of grinding, sharpening and honing edge tools.
The principle
Firstly grind the edge to its correct shape before you start sharpening. Viewed from the
side, the edge should look like a straight line, as in the line drawing below showing the
edge plane angle, (g).
The edge is now blunt, which clearly can be observed as it reflects light. You should see
light reflecting along the entire edge. This blunt edge is called line of light and is a guide
for you where to grind. By closely observing the line of light and only grinding where it is
thickest, you will achieve a perfectly ground edge. The grinding must stop immediately
when the line of light has just been ground away!
Good light is very important for all grinding and honing
work, but it is a demand when grinding carving gouges and
V tools, as you must clearly be able see the line of light.
Carving gouges and V tools have wings. These lean more
or less forward when the bevel lies flat on the wood. The
inclination can be described as the edge plane angle, (g).
This angle controls how the tool will cut in the wood. It
should be around 20° to make the wings and the centre
part of the edge work in the best way and leave a clean cut Bevel viewed from side of gouge
in the wood. This recommendation is independent of the showing edge plane angle.
edge angle.
Grind the edge to its correct The edge plane angle (g) Flatten and smooth the blunted
shape. should be approx. 20°. edge with a fine grit honing
stone.
21
The basics of grinding, sharpening and honing edge tools.
The edge is ground to the Grind only where the line of light Stop grinding immediately when
correct shape. The line of light is thickest. the line of light disappears,
shows you where to grind. which is a sign that the edge is
sharp.
The grinding of the bevel can be done either free hand on bench stones or with jigs on a
grindstone. Using jigs is easier and gives you a better result as you then can concentrate
on where the edge touches the grinding wheel without needing to pay attention to the
edge angle and position of the tool which is controlled by the jig.
Dry grinding on high speed grinders and belt grinders is absolutely not recom-
mended! They grind too aggressively, which makes it impossible to control the grinding
and the heat development draws the hardening of the thin steel.
After the grinding, the bevel is honed to give it as fine a surface as possible. The remain-
ing burr on the flute (inside) must also be honed off. The outside honing can be done free
hand with a fine grit bench stone or with jigs on a rotating felt or leather wheel. The inside
can be honed freehand with slipstones or on profiled honing wheels.
The honing is of the greatest importance as a finer surface on the bevel and flute makes
the tool cut more easily and also makes the sharpness last longer. The surface left on the
wood will also be smoother with a perfectly honed tool.
Also using jigs for the honing is an advantage. You work at exactly the same honing angle
as the grinding angle and the edge receives exactly the same movement pattern towards
the honing wheel as when grinding. Furthermore, you can make test cuts in the wood and
then – if necessary – go back and continue the honing operation with exactly the same
position of the tool towards the honing wheel.
22
The basics of grinding, sharpening and honing edge tools.
Note:
The TORMEK leather honing wheels work in the same way as a strop made of leather
glued onto a piece of wood.
If you look at the edge under a microscope, you will notice that the very outer tip of the
edge is slightly rounded off as the leather honing wheel is not as firm as a stone. Howev-
er, when using a jig this rounding off is negligible and has no negative influence on the
cutting ability of the tool. Actually it is likely that the microscopic rounding off reinforces the
very outer sensitive tip of the edge.
Theoretically, an edge tip honed on a flat hard bench stone could be considered to be
sharper. However, this is only the case before you start to work with the tool. As soon as
the edge penetrates into the wood, it will be affected by the fibres and become microscop-
ically rounded off and even bent. This is because the outer tip is extremely sensitive on
these tools, which have small edge angles, sometimes only 20°.
What determines the practical quality of the edge sharpness and its durability, is
how the tool works after a couple of cuts in the wood.
23
The basics of grinding, sharpening and honing edge tools.
Edge angles
Carving tools are usually ground with a 20° to 25° edge angle. The angle is a compromise
between the easiest possible cutting and the maximum durability of the edge. For soft
wood you can go down to 20° or even less. For hard wood, and when you use a mallet,
you will need a 30° angle or even larger to create an edge which is strong enough.
The choice of edge angle is very important for a carving tool. You can be tempted to
make the angle too narrow in order to make the tool cut as easily as possible. Then there
is a risk that the edge is too weak and becomes easily damaged by the wood. There is a
noticeable difference in the strength of a tool with a 22,5° edge angle and one with a 20°
edge angle.
You might ask, why not put a 25° edge angle on the tool to be sure that it works in any
wood, but it is not that simple. An edge angle which is too large does not cut satisfactorily
in a soft wood because the fibres becomes depressed before they are cut. Furthermore, it
is easier to work with a tool, which has an edge angle which is as small as possible. You
need to test and learn which is the optimal edge angle for your tool and the specific work.
If you work in various hardnesses of wood, it is recommended that you have more than
one tool and grind them with different edge angles.
With the TORMEK System you can measure the edge angle on a tool and set the angle
before grinding. Write the angle on the ferrule.
A 20° edge angle is suitable for A slight increase to 22,5° can When using a mallet you need a
soft wood, but is too weak and enable the edge to withstand 25° or even larger edge angle
can easily get damaged in working in harder wood. depending on the hardness of
harder wood. the wood.
24
The TORMEK method
of grinding, sharpening
and honing.
With the TORMEK method you do not use a conventional bench grinder for the grinding,
coarse benchstones for the initial sharpening or fine benchstones for the fine sharpen-
ing/honing.
You do both the initial grinding (when you shape the tool and create the optimal edge
angle) and the sharpening on the same grindstone. The grindstone can easily be changed
from fast grinding to fine sharpening. The grinding/sharpening is carried out with water
cooling, so there is no risk of burning the edge and drawing the hardening from the steel.
The honing and polishing is carried out on a leather honing wheel.
The surface of the grindstone can easily be maintained flat and true with the TORMEK
Diamond Truing Tool.
The grinding and sharpening on the grindstone as well as the honing and polishing on the
leather honing wheel is controlled with uniquely designed jigs. This means that you have
full control of the grinding, sharpening and honing angles.
By means of a patented Angle Master you can exactly pre-set the edge angle which you
have selected.
Precise replicate sharpenings are possible. Once you have ground your tool to the
desired shape and edge angle, you can easily reproduce exactly the same shape with all
future sharpenings. This is even possible for “difficult” tools with special shapes such as
fingernail turning gouges, spoon shaped woodcarving gouges and oval skew chisels with
a curved edge.
Because of the exact repeatability, you remove very little material and therefore the
sharpening is completed quickly. The result is that the lifetime of your tools is con-
siderably prolonged.
The fact that you exactly can replicate the shape of an edge is a great advantage when
working with a tool. You can continue with exactly the same turning and cutting technique
you have learned for the specific tool, as it has not changed its shape and cutting charac-
teristics.
25
The TORMEK method of grinding, sharpening and honing.
SuperGrind stone
Removable
water trough
This SuperGrind 2000 series is described and used for all photos and line drawings in this
handbook. The smaller SuperGrind 1200 series works in the same way and uses the
same range of jigs and accessories.
For specifications and technical data for each model, please see the chapter Models,
page 140.
26
The TORMEK method of grinding, sharpening and honing.
27
The TORMEK method of grinding, sharpening and honing.
Perfect visibility of the sharpening process
As the grindstone runs slowly in water and no sparks are produced, there are no eye
shields on the machine. This means that you can clearly watch and control the sharpen-
ing process.
Flat surface
The outside of the SuperGrind stone is machined flat
and has a depressed centre so the grinding surface
does not interfere with the washer and nut in the centre.
This surface is reserved for flattening the back of plane
irons, wood chisels and similar tools.
28
The TORMEK method of grinding, sharpening and honing.
Safe
At the low speed of the TORMEK grindstone, you can
fully control the grinding operation.
No sparks are produced so you can use the machine in
areas of high fire risk. Furthermore, the wheel cannot geprüfte
Sicherheit
shatter and injure people.
TORMEK machines are CE-marked and are approved
by SEMKO in Sweden, CSA in Canada and TüV, the
German safety standards authority.
29
The TORMEK method of grinding, sharpening and honing.
30
The TORMEK method of grinding, sharpening and honing.
Continuous operation
The single phase motor is the highest industrial quality and is rated for continuous opera-
tion. (The SuperGrind 1200 is rated for 30 min/hour.)
Quiet running
TORMEK machines run very quietly thanks to the silent induction motor and the patented
friction drive.
No grinding dust
No sparks are produced and the steel and grindstone particles are transported by the
water into the water trough. Therefore you get no dust in the air and around the machine,
which is better for your lungs.
31
32
Instructions
33
Instructions. Safety.
Safety
TORMEK Water Cooled Grinders run at a slow speed in water and are designed for maxi-
mum safety. However – as with all machines – there are some basic rules that must be
followed and we ask you to read these instructions before you commence working with
the machine.
• Make sure that the switch is in the off position before plugging in to the power supply.
• The machine should be operated on a flat, stable surface. Keep work area clean.
Cluttered areas and benches invite accidents. Keep work area well lit.
• Do not wear loose clothing, gloves, neckties, rings, bracelets etc, which can get caught
in the moving parts. Keep long hair covered or tied back. Keep a proper footing and
balance at all times. Non slip footwear is recommended.
• Ensure that any spanners or adjustable wrenches are removed from the grinding
machine before turning it on.
• Do not lift the machine by gripping the Universal Support – it could pull out and allow
the machine to drop.
• Always keep a part of the tool on the grindstone during grinding – do not let it wholly
slip outside the stone.
• Grinding direction:
When working free-hand, grind in the direction
of rotation, i.e. away from the edge
• Honing direction:
Always hone in the direction of rotation (away
from the edge), otherwise the edge can cut
into the wheel.
• Only use TORMEK original jigs and accessories and according to the instructions.
• The TORMEK jigs and accessories are especially designed for TORMEK machines
and must not be used on any other grinder.
• Do not use the machine in a dangerous environment, e.g. wet locations and do not
expose it to rain.
34
Instructions. Safety.
35
Instructions. Preparation before grinding.
Light
Ensure that you have satisfactory light, so that you can see clearly and can control the
grinding process in detail. A perfect light is absolutely necessary when you grind small
and delicate woodcarving tools.
Water filling
Fill the trough with the grindstone running and with the
trough raised, until the water reaches the MAX WATER
LEVEL line inside the trough. Continue filling until the
stone cannot absorb any more water, which is approx.
1,2 litre (2 pints).
The stone must run in water at all times when grinding.
36
Instructions.The Universal Support.
Vertically in the two sleeves. Horizontally for grinding away Horizontally for honing away
For grinding towards the edge. from the edge. from the edge.
37
Instructions. Setting the edge angle.
Wrong setting
Colour the entire bevel with a Check where the sharpening will Here the stone is hitting the heel
marker. take place by rotating the grind- of the bevel.
stone by hand.
Correct setting
38
Instructions. Setting the edge angle.
This bevel colouring method is especially useful when re-sharpening turning bowl gouges,
woodcarving gouges and planer or jointer blades.
This method is also ideal when setting the honing angle. In this case you should check
the setting with the honing wheel running.
39
Instructions. Pro AngleMaster WM-200.
Magnets (2 pcs)
Measuring grooves
For fixing the Pro Angle-
For measuring an existing Master to the steel
edge angle. housing.
• •
40
Instructions. Pro AngleMaster WM-200.
0 mm
Ø 25
Setting a plane iron with a 25° edge angle on a 250 mm (10") grindstone.
0 mm
Ø 18
Diameter compensator
The same edge angle on a stone worn down to 180 mm (7"). The wear of the stone is compensated
by setting the diameter compensator to the stone diameter.
41
Instructions. Pro AngleMaster WM-200.
5 mm
Ø 22
Setting of a bowl gouge at 45° edge angle in the SVD-180 jig. Stone diameter 225 mm (9").
The scale shows that the stone The diameter compensator is set
diameter is Ø 230 mm. on Ø 230 mm.
42
Instructions. Pro AngleMaster WM-200.
Note:
When making a setting to a different edge angle, you should compensate for the material
that will be removed on the edge. The exact angle can be measured when the entire new
bevel touches the stone.
Measuring the edge angle of a knife. Measuring the edge angle of a bowl gouge.
43
Instructions. Straight Edge Jig, SVH-60.
• plane irons
• wood chisels
• spoke shave
blades
Positioning
of the machine
Design 2
The jig comprises a base (1) and a clamp (2) for holding 1
the tool in position. The jig slides across the grindstone
guided in nylon bushings on the Universal Support.
The edge angle is set by adjusting the height of the
Universal Support.
Grinding direction
Plane irons and wood chisels are best ground towards the edge with the Universal Sup-
port placed vertically. You then achieve a higher grinding pressure, which is preferable
since the grinding area is large. Here there is no risk of accidentally overgrinding as the
area of the bevel is flat and large.
44
Instructions. Straight Edge Jig, SVH-60.
Flatten the back of the tool by Grade the grindstone to a finer Do the final smoothing on the
holding it flat to the grindstone surface by pressing the fine graded stone.
while moving it slightly. side on the grindstone for 30 -
60 seconds.
N.B.
You must keep the tool absolutely flat against the grindstone. Otherwise the tip can cut
into the wheel and be rounded off. Let the side of the tool rest on the Universal Support
placed close to the stone as shown. You do not need to smoothen the tool more than
25 - 30 mm (1 - 1 1/4") from the edge.
Preparations
Before you start grinding, check If necessary, true it with the Dia-
that the stone is true by letting mond Truing Tool ADV-50D so
the Universal Support touch the the surface is flat and parallel to
stone. the Universal Support.
45
Instructions. Straight Edge Jig, SVH-60.
1 2
P
•
Mount the tool protruding (P) For a wood chisel you should check that the entire top face is in
approx. 50 mm (2"). contact with the clamp (2) and that this clamp is parallel to to the
For tools with parallel sides, base (1). This is important for achieving an exact 90° grinding.
check that the tool rests against Align the chisel and the clamp (2) by adjusting the knobs. Loosen
the two stops. one knob whilst tightening the other.
Grinding
Set the edge angle by adjusting Press with your fingers close to Ensure that half of the blade is
the Universal Support. Either at the edge for best control. Move always in contact with the stone.
the original angle using the the tool across the stone.
bevel colouring method (page
38) or at a new angle using the
Pro AngleMaster WM-200,
(page 40).
The amount of grinding on each spot along the edge depends upon both the pressure and
the time that it is in touch with the stone. Therefore you should compensate for the fact
that the middle of the plane iron is always in touch with the stone, by grinding more at the
sides.
Check that you are grinding evenly. You can remove the jig from the Universal Support
with the tool mounted.
Towards the end of the grinding, apply a lighter pressure onto the stone and you will
achieve a finer surface.
You should aim to grind a plane iron as closely as possibly to square. However, in prac-
tise it does not need to be an exact 90°, since you can compensate for a deviation of one
or two degrees with the setting in the plane.
46
Instructions. Straight Edge Jig, SVH-60.
Finer surface
Grade the stone to a finer grit Do the fine sharpening with the
with the Stone Grader SP-650. same jig setting until you have
Check with your fingers that the achieved a finely ground surface
stone is entirely smooth. across the entire bevel.
Honing
Hone the bevel with the tool mounted in the jig as you then have full control of the honing
angle. You can use a higher honing pressure and so achieve a more effective and faster
honing.
Turn the machine around so that the honing wheel rotates away from you and move the
Universal Support to the honing wheel side. Hone the back of the tool free-hand.
Set the Universal Support so Move the tool sideways during The back is honed free-hand.
that you get the same honing the honing.
angle as the grinding angle. Use
the bevel colouring method.
47
Instructions. Straight Edge Jig, SVH-60.
Secondary bevel?
Some people recommend that you should put a secondary bevel (or microbevel) on your
plane irons and wood chisels. The reason is that the honing work after the grinding is
quicker since you do not need to hone the entire surface of the bevel, just the smaller new
bevel at the tip.
For wood chisels there is a drawback with a secondary bevel since you do not have the
support of the large original bevel to control the cutting in the wood.
For plane irons, a secondary bevel increases the risk that the heel of the secondary bevel
will touch the wood and cause chattering.
Since the grinding and honing of the entire bevel with the TORMEK method is an easy
and fast operation, there is no need for a secondary bevel. With a single bevel, you can
set exactly the angle that you want and easily maintain it at every grinding and honing.
48
Instructions. Straight Edge Jig, SVH-60.
Edge angle
a
Plane irons, wood chisels and spoke shave blades are
usually ground with a 25° edge angle (a).
a
If you need to work delicate details with a wood chisel in
soft wood, you can decrease the edge angle down to 20°.
If you work in hard wood and when using a mallet, you a
must increase the edge angle to 30°.
49
Instructions. Planer/Jointer blade Jig, SVH-320.
Positioning
of the machine
Grinding direction
towards the edge.
Design
The grinding jig comprises support (1), blade holder (2) and allen key (3).
In this jig the tool is guided precisely and ground flat along its whole length to a pre-set
fixed depth. This is not the case with the other TORMEK jigs, where your hand decides
where the grinding occurs and the depth of grinding.
It is important that the grinding angle is set with great accuracy. If you follow the detailed
step by step instructions carefully, you will be satisfied with the results.
2 3
1
The grinding jig comprises support (1), blade holder (2) and allen key (3).
50
Instructions. Planer/Jointer blade Jig, SVH-320.
Planer/jointer blades
Check that the grinding wheel is Remove the Universal Support Clamp the blade in the holder.
exactly round and that the grind- and place the support in the Make sure that it rests on the
ing surface is even. Adjust if sleeves of the machine. If stop along the entire length.
necessary with the TORMEK required, remove the honing Always commence with any
Diamond Truing Tool ADV-50D. wheel. damaged blade in the set.
12-20 mm
12-20 mm (1/2-3/4")
(1/2-3/4")
Colour the grinding bevel with a Place the blade holder on the support and set the grinding length
marker pen so that you can see to the length of the blade. This is done by adjusting and locking
where the grinding occurs when both stops (5) to ensure that the blade does not run off the edge of
setting the edge angle. the stone during grinding.
2 1 7
•
6
a •
Grind the blade at exactly the Make an initial height setting with the wheels (6). Set the edge
original edge angle (a). angle with the adjusting screw (7). Make fine adjustments to the
height with the wheels (6). The bevel should now lie flat on the
stone and the holder (2) should touch the support (1).
51
Instructions. Planer/Jointer blade Jig, SVH-320.
Check the angle setting by turn- Press down the grinding jig while Make sure that the blade makes
ing the wheel by hand. The locking with the locking screws contact along the whole width of
stone should make marks on so that the two wheels (6) rest the wheel – a thin piece of paper
the whole bevel, from the tip to on the base without any gap. simplifies this check. Adjust if
the heel. necessary with the wheels (6).
Important!
Do the angle setting with care to get exactly the same edge angle as the existing one. If
you set the jig to grind the heel of the bevel, the operation will take unnecessarily long time.
8
Set the grinding depth by raising the wheels (6). Turn the Unlock the two locking screws
wheels equally in order to retain the parallel setting. The grind- (8) and allow the support plate
ing depth is shown on the two wheels (6) which are graduated to lower by the amount you
for each 0,1 mm (0,004"). have raised the wheels (6).
Lock the support plate – while it There is now a gap between the
is pressed down – with the two blade holder and the support.
locking screws (8).
52
Grinding
Tip:
If the grinding effect of the stone
decreases during the operation,
the stone can easily be reacti-
vated with the TORMEK Stone
Grader SP-650, whereby new
grinding grains are brought into
operation.
Honing
Hone away the burr gently on
the leather honing wheel. Start
with the reverse side and then
the bevel and repeat this a
couple of times.
Important:
Always hone away from the
edge!
Instructions. Planer/Jointer blade Jig, SVH-320.
53
Instructions. Planer/Jointer blade Jig, SVH-320.
The distance between the clamping screws varies to fit different widths. Use the smallest
possible distance to avoid deflection of the holder when tightening.
A up to 50 mm (2").
B up to 60 mm (2 3/8").
C up to 75 mm (3").
A set of mitre guillotine blades. Use a 3 mm allen key to remove Mount the blade so the edge is
one of the screws. parallel to the blade holder.
54
Instructions. Universal Gouge Jig, SVD-180.
Carving tools
• Straight gouges
• Curved gouges
• Spoon-shaped gouges
• Back bent gouges
• Down bent gouges
• Tapered gouges
• V tools, curved and straight
Positioning
of the machine
Design
The jig comprises a tool holder (1) which runs on a sleeve (2). The tool is mounted with
the screw (3). The stop ring (4) can be set for a convex bevel.
The tool holder can be turned and locked in any position with the allen key (5).
The settings are marked from 0 to 5.
The setting can be noted on a special recipe label (6), which is attached to the ferrule.
A special pen, which works on these labels is included (7).
3 • 1 2 4 5 6 7
•
• • •
• •
55
Instructions. Universal Gouge Jig, SVD-180.
You can grind turning gouges with the so called fingernail shape as well as carving
gouges with various shapes. You can also grind straight and curved V tools.
The jig causes the tool to move towards the grindstone in a special way, according to the
setting selected from 0 to 5. This means, that for turning gouges you can decide the maxi-
mum length of the side edges. For carving gouges, which are not ground with a finger-
nail shape, the jig setting compensates for the shape of the shank.
The jig can be set from 0 to 5, ...turning gouges with various ...carving gouges with various
which permits the grinding of… lengths of side bevels and… shapes and V tools.
56
Instructions. Universal Gouge Jig, SVD-180.
Turning gouges
Bowl gouges
The instruction is divided into two sections.
The first section shows how to shape a
gouge to a new profile and the other shows
how to re-sharpen an existing profile.
Shaping a gouge takes 5 to 20 minutes
depending on how much steel you need to
remove. This is a time investment you only
do once for the gouge. Re-sharpening an
existing profile, which is the most frequent
use of the jig, takes just 30 – 45 seconds
including the settings.
57
Instructions. Universal Gouge Jig, SVD-180.
Fingernail shape on a bowl gouge at various edge angles and jig settings
JS 0
JS 1
JS 2
JS 3
JS 4
JS 5
• Protrusion 65 mm (2 1/2").
• Wings ground back to the maximum and with a slightly convex shape.
58
Instructions. Universal Gouge Jig, SVD-180.
Recommended shapes
When deciding the jig setting, you must take into consideration which edge angle you
have or want on your gouge. At a narrow edge angle 35°, jig setting at 2 gives pro-
nounced wings whilst at a 60° angle you need to set the jig on 5 to get the same length on
the wings.
Those manufacturers, who deliver bowl gouges ground with a fingernail shape, grind an
edge angle of 45° or 60° on their gouges and the profiles correspond to jig setting 2 and 5.
The large 60° edge angle, or even a larger angle, is needed when turning the bottom of
deep bowls enabling the bevel to rub. For external turning, a smaller edge angle can be
preferable as this cuts more easily, e.g. 35° with setting 2.
Generally, you should use an edge angle as narrow as the hardness of the wood permits,
because a smaller edge angle cuts more easily than a larger one and the risk of vibration
is less. Hard and tough woods with knots require a larger edge angle than a softer wood.
The finer the surface of the edge... the more durable the sharpness. Since you achieve a
finer surface with the TORMEK sharpening and honing method compared with conven-
tional dry, high speed grinders, you can decrease the edge angle and thus your tools will
cut more easily.
The combination of edge angle and jig setting you should use, depends upon which type
of turning you do most and the way you want the tool to behave. There are no “rights” or
“wrongs” – your experience will tell what works best for you. A good tip is to use more
than one gouge and shape them differently so you can quickly go from one type of turning
to another without being forced to go to the grinder and change the shape. One or two
extra gouges used in this way will save you a considerable amount of time and avoid
unneccessary waste of your expensive tools.
2 4
P • •
Select the jig setting, which cor- Mount the gouge protruding (P) Check that the disc aligns the
responds to the shape you want 65 mm (2 1/2"). gouge properly.
on the gouge. (See the previous The stop ring (4) must be locked
page). Tighten the screw proper- close to the sleeve (2).
ly.
59
Instructions. Universal Gouge Jig, SVD-180.
Tips:
P
Protrusion Measure
Bench
Place the self-adhesive measure, which comes with the jig, on a If you need to clamp the gouge
piece of wood and glue a stop at 65 mm (P). This simple device on the circular section (e.g. short
will make the protrusion setting easier. gouges), flatten the shaft on the
grindstone so that the gouge
does not turn in the jig.
60
Instructions. Universal Gouge Jig, SVD-180.
Do the first coarse grinding on Move the tool sideways so you use the whole width of the stone
one side at the time and you and avoid creating grooves.
avoid having to swing the tool
from side to side.
Tip:
If you need to remove a lot of metal on a gouge at the initial shaping, you can save time
by creating the first rough shape free hand on a conventional high speed grinder, which
removes steel faster due to the high speed. Watch that you do not overheat the edge.
61
Instructions. Universal Gouge Jig, SVD-180.
Grind the other side. Again use Check frequently to ensure that Decrease the grinding pressure
the whole width of the stone to you are grinding evenly. Grind as you complete the shape and
wear the stone evenly. more where it is needed. finish the grinding (now sharpen-
ing) with a full swing over the
entire bevel.
Honing
Keep the tool in the jig and hone Hone and polish the bevel on the large, standard leather honing
and polish the inside on the wheel. Set the Universal Support so that the honing angle is the
Profiled Leather Honing Wheel same as the grinding angle. Use the bevel colouring method,
LA-100. described on the next page. Hone away the burr and polish the
bevels to a mirror finish.
Note the jig setting (JS) and the protrusion (P) on a recipe Put the label on the ferrule and
label. Use the special permanent pen, which comes with the jig. you can repeat the same setting
Also note the approx. edge angle (a). when re-sharpening.
62
Instructions. Universal Gouge Jig, SVD-180.
P
Protrusion Measure
Set the jig with the same setting Mount the gouge in the jig with Check that the disc aligns the
(JS) as noted on the label. the same protrusion (P) gouge properly.
Wrong setting
Colour the entire bevel with a Check in the centre of the gouge Here the stone is hitting the heel
marker. where the sharpening will take of the bevel. The Universal Sup-
place by rotating the grindstone port needs a small adjustment
by hand. away from the stone.
63
Instructions. Universal Gouge Jig, SVD-180.
Correct setting
This is the correct setting. The Sharpen. Swing the jig from
stone hits the full length of the side to side and sharpen with a
bevel. The sharpening will now light pressure until the colouring
exactly follow the shape of the has disappeared on the entire
entire bevel profile. bevel.
P
Protrusion Measure
Universal
Support
Mount the gouge in the jig with Check that the disc aligns the Place the prepared wooden dis-
the same protrusion (P) gouge properly. tance piece between the Univer-
sal Support and the grindstone,
and set the Universal Support
accordingly.
Note
The wooden distance piece method assumes that the stone diameter has not changed too much
since the last sharpening. However, the difference in the result is only theoretical and hardly notice-
able. For each 10 mm (3/8") decrease of the stone diameter the edge angle will decrease max 1°.
If after a period of time the stone diameter has decreased more than you can allow, you can use the
method A to achieve exactly the same edge angle, or you can make a new wooden piece to fit the
smaller stone diameter.
64
Instructions. Universal Gouge Jig, SVD-180.
Sharpen
Swing the jig from side to side and sharpen with light pressure.
Since you exactly repeat both the existing edge angle and the
existing fingernail profile, the sharpening is done in less than 30
seconds.
Tips
• You can shape the wooden piece to fit more than one gouge.
Then note their edge angles.
• If you use two favourite jig settings, you can have two jigs, both with a specific and fixed setting,
which will save you time.
Honing
Keep the tool in the jig and hone Hone and polish the bevel on the large, standard leather honing
and polish the inside on the wheel. Set the Universal Support so that the honing angle is the
Profiled Leather Honing Wheel same as the grinding angle. Use the bevel colouring method.
LA-100. Hone away the burr and polish the bevel to a mirror finish.
65
Instructions. Universal Gouge Jig, SVD-180.
a b
1
You can round off the heel by Now grind the heel of the bevel If you want a smooth convex
moving the stop ring (4) and the by pressing the jig towards the bevel without a step, you slide
sleeve (2) backwards. A scale grindstone so that the stop ring the jig continuously back and
on the jig shows the extent of the (4) is in touch with the sleeve (2). forth between the two outer
movement. positions during the grinding
operation.
c a b c
Secondary bevel
You can also move the Universal The methods described will give you these alternative shapes. The
Support closer towards the size of the secondary bevel and the degree of rounding off can be
grindstone. This gives you a made according to your requirements.
more pronounced secondary
bevel.
N.B.
The edge angle, which is measured at the tip, remains the same on all of the examples.
66
Instructions. Universal Gouge Jig, SVD-180.
Spindle gouges
Spindle gouges are ground, sharpened and honed in the same way as bowl gouges. The
edge angle is usually 25° to 35° and a jig setting on 3 will give a suitable finger nail profile.
67
Instructions. Universal Gouge Jig, SVD-180.
Carving Gouges
The principle
Use the technique as described in the chapter Grinding techniques for carving gouges
and V-tools on page 20.
Edge angle
As described in the above chapter on page 24, the choice of edge angle is very important
for a carving gouge
The method of setting the jig for a certain angle depends on whether you want to replicate
an existing edge angle or if you want to put a new edge angle on your tool.
When replicating an existing edge angle, you should use the bevel colouring method,
which is described on page 38. If you want to put a new edge angle to your tool, you can
either set the angle by eye or you can use the Pro AngleMaster, page 40.
Shape the edge by resting the The edge plane angle (g) Flatten and smooth the blunted
tool on the Universal Support should be approx. 20°. Please edge with the fine side of the
placed horizontally and close to see page 21. TORMEK Stone Grader, SP-650.
the stone.
68
Instructions. Universal Gouge Jig, SVD-180.
Tip:
When cutting steep bowls
using a curved or a down 90°
bent gouge, the edge plane
Line of light
angle can be decreased.
Here it is 0°
Now you have a line of light,
which is your guide as to where
to grind.
2 4
P • •
Mount the gouge in the jig pro- Put the jig on the Universal Now the jig is set to suit the
truding approx. 100 mm (4"). Support and swing it to one side. curve of the gouge. The edge
The stop ring (4) must be locked Set the jig so that the plane of angle will be equal across the
close to the sleeve (2). the edge is approx. parallel to edge. If the thickness of the steel
the axis of the stone. is even, the bevel length will also
be equal along the edge.
Tip:
If the shank has a convex upper
side, you should grind it flat to
make sure that the tool does not
turn in the jig.
69
Instructions. Universal Gouge Jig, SVD-180.
Grinding
Line of light
Always grind where the line of Check frequently where the Grade the grindstone for fine
light is the thickest while swing- grinding takes place. Grind until sharpening with the fine side of
ing the tool. you get an even and thin line of the Stone Grader SP-650.
light.
Continue sharpening. Check the Remove the burr on the leather honing wheels to observe the line
result frequently. of light more clearly. The tool is left mounted in the jig.
Sharpen again. Now with a very Stop sharpening immediately Be careful when you grind at the
light pressure. Check frequently when the line of light dis- sides of the gouge so you do not
so that you do not over-sharpen. appears, which is a sure sign round off the corners. Wood-
that the edge is sharp. carving tools should have sharp
corners!
Important!
It is very easy to be misled by the burr and mistake the burr for the line of light! Therefore
you must remove the burr frequently during the finishing of the grinding operation, so you
clearly can watch the progress of a gradually thinner line of light.
70
Instructions. Universal Gouge Jig, SVD-180.
N.B.
Honing
Keep the tool in the jig and hone Hone and polish the bevel. Set the Universal Support so that the
and polish the inside on the honing angle is the same as the grinding angle. Use the bevel
Profiled Leather Honing Wheel colouring method. Hone away the burr and polish the bevel to a
LA-100. mirror finish.
Leave the tool in the jig and test If the edge needs further honing or sharpening on some spots, you
the sharpness by pushing the can continue with the same setting.
edge across the fibres in a piece When you are satisfied with the result, you remove the tool from
of wood. The edge should cut the jig after having measured and noted the protrusion (P) and
easily and leave a smooth sur- the jig setting. Please see the next page.
face without tearing the fibres.
71
Instructions. Universal Gouge Jig, SVD-180.
Note the jig setting (JS) and the protrusion (P) on the label. Use Attach the label to the ferrule
only the special pen which comes with the jig. Also note the and you are assured that you
approx. edge angle, (a). have the same data at future
sharpenings.
A back bent gouge is ground You can also grind a down bent
with the jig setting 0. gouge. The jig is set as shown
on page 69.
72
Instructions. Universal Gouge Jig, SVD-180.
V tools
These tools are considered the most difficult
to grind. The reason is that it has two edges
joined with a radius.
However, with the method described here,
you will also manage to achieve a sharp and
correctly shaped edge on these tools.
The principle is the same as for carving
gouges, i.e. you first give the tool its right
shape and then let the line of light guide you
as to where to grind.
The principle
Use the technique as described in the chapter Grinding techniques for carving gouges
and V-tools on page 20.
Edge angle
As described in the above chapter on page 24, the choice of edge angle is very important
for a carving gouge
The method of setting the jig for a certain angle depends on whether you want to replicate
an existing edge angle or if you want to put a new edge angle on your tool.
Shape the edge. Rest the tool The edge plane angle (g) Flatten and smooth the blunt
on the Universal Support posi- should be approx. 20°. Please edge with the fine side of the
tioned horizontally. see page 21. TORMEK Stone Grader, SP-650.
73
Instructions. Universal Gouge Jig, SVD-180.
2 4
P • •
Mount the tool in the jig protrud- Put the jig on the Universal Now the jig is set to suit the
ing approx. 100 mm (4"). Support and turn it so one wing shape of the tool, the edge angle
The stop ring (4) must be locked lies flat on the grindstone. Set will be uniform.
close to the sleeve (2). the jig so that the edge is
approximately parallel to the
axis of the stone.
Grinding
Control the grinding pressure Check frequently where the Do not slide the tool sideways.
with your thumb and control grinding is taking place. Only Keep it on the same spot on the
where the grinding takes place grind where the line of light is grindstone for the best control.
by gently turning the tool with the thickest.
your hand.
Rest your hands on the Universal Support and you get a good control.
74
Instructions. Universal Gouge Jig, SVD-180.
Grind until you get an even and Now grind the other wing in the Then grind the keel. Turn the
thin line of light. same way. tool from side to side to equalise
the grinding towards the wings.
Grade the grindstone for fine Continue sharpening one wing Remove the burr on the leather
sharpening with the fine side of at a time and then the keel. honing wheels so that you can
the Stone Grader SP-650. Check the results frequently. better observe the line of light.
Important!
It is very easy to be misled by the burr and mistake the burr for the line of light! Therefore
you must remove the burr frequently during the finishing of the grinding operation, so you
clearly can watch the progress of a gradually thinning line of light.
75
Instructions. Universal Gouge Jig, SVD-180.
Honing
Keep the tool in the jig and hone Hone and polish the bevels. Set the Universal Support so that the
and polish the inside on the honing angle is the same as the grinding angle. Use the bevel
Profiled Leather Honing wheel colouring method. Hone away the burr and polish the bevels to a
LA-100. mirror finish.
N.B. Tip:
It is easy to over-grind the edge This is now how the tool should The tool cuts more easily if you
at the end of the grinding. If this appear. The keel is slightly round the keel. Move the Univer-
happens, you need to reshape longer than the bevel of the sal Support slightly towards the
the edge and start again from wings since the steel is thicker grindstone and grind gently while
the beginning. in the centre. swinging the tool from side to
side.
76
Instructions. Universal Gouge Jig, SVD-180.
77
Instructions. Multi Jig, SVS-50.
Turning tools
• Square and skew chisels
with straight or curved edges.
• Parting tools
• Beading tools
• Roughing gouges
Carving tools
• Gouges, 25 - 50 mm (1" - 2").
Straight shanked or tapered.
• Square and skew chisels
Positioning
of the machine
Grinding direction:
away from the edge. Max tool width 50 mm (2").
Design
This patented jig consists of a housing (1) and two interchangeable seats – one closed,
(2) and one open, (3). The seats can swivel and can be locked at any skew angle
between 0° and 45°.
Skew chisels have symmetrical bevels on both sides. With this jig you mount the tool only
once for grinding both the bevels. By turning the jig upside down you can grind both of the
bevels symmetrically.
5
• 1
2 3
•
•
6 4
78
Instructions. Multi Jig, SVS-50.
The closed seat has been developed for the precision sharpening of turning skew chis-
els with an oval or square section and with curved or straight edges. Since the chisel is
mounted in the centre of the seat, the bevels are ground to exactly the same shape. The
turning skew chisel is mounted with a side screw (4). Tool size 13 mm (1/2") to 35 mm
(1 3/8").
It is also suitable for carving skew chisels longer than approx 110 mm (4 3/4").
The open seat, where the tool is fixed with a top screw (5), is used for tools which have
the edge ground square across the shank, such as parting tools, roughing gouges and
wide carving gouges.
Both seats are mounted with a bottom screw (6), which also locks the chosen skew angle.
A scale on each seat shows the skew angle.
4 5 • 5 • 5 •
6 • 6 • 6 •
The closed seat is for skew The open seat is designed for tools which have the edge square
chisels. The tool is fixed with the across the shank. The tool is fixed with the top screw in the hous-
side screw (4). The top screw ing (5).
(5) is not used. As the seat can be turned, it can also be used for short skew chis-
els (page 93).
Grinding direction
Grinding away from the edge with Universal Support placed horizontally is recommended.
This gives you following advantages:
• With the lighter grinding pressure you can more easily control the operation. Especially
advantageous when grinding small tools.
• As no water flows over the edge, it is easier to see where the grinding takes place.
• The rotation of the stone pulls the jig towards the Universal Support.
• No risk of vibration.
79
Instructions. Multi Jig, SVS-50.
Turning tools
Turning skew chisels.
The closed seat is used.
4
P
Mount the tool in the jig protrud- Mark a line across the stone Put the tool on the Universal
ing (P) approx. 75 mm (3") and guided by the Universal Support. Support and turn it until the
lock it with the side screw (4). Use a water proof pen if the bevel is parallel to the line.
stone is wet. Tighten the bottom screw (6).
4
P
A scale on the seat enables you Lock the position with the bot- Mount the tool in the jig protrud-
to set the desired skew angle. tom screw (6). ing (P) approx. 75 mm (3") and
lock it with the sidescrew (4).
80
Grinding
Important
Tip:
Lift the tool and then move it
sideways during the grinding.
Do not slide the tool. Press with
your thumb close to the edge for
best control.
When shaping a wide chisel, you can increase the efficiency of the
stone by grinding half the width at a time. Then the grinding sur-
face is decreased and the grinding pressure will correspondingly
increase, which makes the stone grind faster. Please see the
chapter Grinding pressure.
Instructions. Multi Jig, SVS-50.
Set the edge angle exactly, so that you do not need to grind away more steel than neces-
sary.
81
Instructions. Multi Jig, SVS-50.
25°
40°
For a chisel with a skew angle Pivote the jig on the corner closest to the tip and let the grindstone
of 25°, you set the jig (JS) on shape the curve. Watch that you grind evenly. Slide the jig side-
35° - 40°. ways so you use the whole width of the stone.
You must not pivote on the square side of the jig (B) otherwise the edge angle moves down the
grindstone and the desired edge angle is lost.
Turn the jig around and grind the Grind until the bevels on both sides are symmetrical. If necessary
other side. grind the first side again.
The shape of the curve is deter- Note the jig setting (JS) and the Attach the label to the ferrule
mined by the amount of grinding protrusion (P) on the label. You and you are assured that you
you do at the sides. can also note the edge angle have the same data at future
(a). sharpenings.
82
Instructions. Multi Jig, SVS-50.
Edge angle
The edge angle (a) should be between 25° and 35°. Your
choice depends on the hardness of the wood.
Honing
Hone the bevels on the leather honing wheel. Move the Universal Support to the honing
wheel side and hone with the tool still mounted in the jig.
Set the Universal Support so Hone both sides alternately until the burr is removed and the
you get the same honing angle bevels are polished to a mirror finsish.
as the grinding angle. Use the
bevel colouring method.
Grinding time
When you grind a new chisel for the first time to your preferred skew angle and shape,
quite a bit of material might need to be removed. This work can take 10 - 15 minutes
depending on the size of tool and how much you are changing the shape. The time spent
on shaping is well invested, because you will benefit during the entire life of the
tool.
Since you use the same jig setting, protrusion and edge angle, re-sharpening takes just
a couple of minutes including setting and honing as the edge only needs a slight touch-
ing up.
83
Instructions. Multi Jig, SVS-50.
7 P
• • 6
• 5
Lock the seat with the bottom Mount the tool protruding (P) Set the edge angle by adjusting
screw (6) in the straight position approx. 100 mm (4") and lock it the Universal Support. When
(0°). The seat should touch the with the top screw (5). replicating an existing angle,
stop (7). use the bevel colouring
method, (page 38).
Press with your fingers close to Ensure that the entire flange of When the first side is ground
the edge for best control while the jig is in contact with the Uni- then turn the tool around – it is
your right hand ensures that the versal Support still mounted in the jig – and
tool is vertical. grind the other side.
Grind until the bevels are sym- Honing. Move the Universal Support to the honing wheel side and
metrical. If necessary grind the hone the bevels with the tool still mounted in the jig.
first side again Set the Universal Support so that you get the same honing angle
as the grinding angle. Use the bevel colouring method.
84
Instructions. Multi Jig, SVS-50.
Roughing Gouges
7 P
• • 6
• 5
Lock the seat with the bottom Mount the gouge protruding (P) Set the edge angle by adjusting
screw (6) in the straight position approx. 100 mm (4") and lock it the Universal Support. When
(0°). The seat should touch the with the top screw (5). replicating an existing angle,
stop (7). use the bevel colouring
method, (page 38).
Roll the gouge on the Universal Ensure that the entire flange of Grind until you can feel the burr
Support while you slide it across the jig is in contact with the Uni- along the entire edge.
the stone so that the stone versal Support.
wears evenly.
Move the Universal Support to the leather honing wheel. Hone and The edge angle should be
polish the bevel with the tool still mounted in the jig. Set the Uni- between 30° and 45° depending
versal Support so that you have the same honing angle as the upon the hardness of the wood.
grinding angle. Use the bevel colouring method.
85
Instructions. Multi Jig, SVS-50.
Carving tools
Carving gouges with a straight shank
The principle
Use the technique as described in the chapter Grinding techniques for carving gouges
and V-tools on page 20.
Edge angle
As described in the above chapter on page 24, the choice of edge angle is very important
for a carving gouge
The method of setting the jig for a certain angle depends on whether you want to replicate
an existing edge angle or if you want to put a new edge angle on your tool.
When replicating an existing edge angle, you should use the bevel colouring method,
which is described on page 38. If you want to put a new edge angle to your tool, you can
either set the angle by eye or you can use the Pro AngleMaster, page 40.
Line of light
Shape the edge by resting the Flatten and smooth the blunt Now you have a line of light,
tool on the Universal Support edge with the fine side of the which is your guide on where to
placed horizontally and close to TORMEK Stone Grader, grind.
the stone. SP-650.
86
Instructions. Multi Jig, SVS-50.
7 P
• • 6
• 5
Lock the seat with the bottom Mount the gouge protruding (P) Set the edge angle by adjusting
screw (6) in the straight position, approx. 100 mm (4") and lock it the Universal Support. When
(0°). The seat should touch the with the top screw (5). replicating an existing angle,
stop (7). use the bevel colouring
method.
Grinding
Line of light
Always grind where the line of Ensure that the entire flange of Check frequently where the
light is thickest whilst rolling the the jig is in contact with the grinding is taking place. Grind
tool on the Universal Support. Universal Support. until you have a thin and even
line of light.
Grade the grindstone for fine Continue grinding. Check the Remove the burr on the leather
sharpening with the fine side of result frequently. honing wheels so that you can
the Stone Grader SP-650. more clearly observe the line of
light.
87
Instructions. Multi Jig, SVS-50.
Important!
It is very easy to be misled by the burr and mistake the burr for the line of light! Therefore
you must remove the burr frequently during the finishing of the grinding operation, so you
clearly can watch the progress of a gradually thinning line of light.
Honing
Keep the tool in the jig and hone Hone and polish the bevel. Set the Universal Support so that the
and polish the inside on the honing angle is the same as the grinding angle. Use the bevel
Profiled Leather Honing Wheel colouring method. Hone away the burr and polish the bevel to a
LA-100. mirror finish.
88
Instructions. Multi Jig, SVS-50.
Remarks:
89
Instructions. Multi Jig, SVS-50.
7 P
• • 6
• 5
Lock the seat with the bottom Mount the chisel protruding (P) Set the edge angle by adjusting
screw (6) in the straight position min 75 mm (3"). Lock with the the Universal Support. When
(0°). The seat should touch the top screw (5). replicating an existing angle,
stop (7). use the bevel colouring
method.
Sharpen the first side. Press with your thumb close to the edge for Ensure that the entire flange of
best control. Lift the tool and then move it sideways so that the the jig is in contact with the
stone wears equally. When a burr has developed on the entire Universal Support.
edge, turn the jig around and sharpen the other side.
Honing. Keep the tool in the jig and move to the leather honing wheel. Set the Universal Support so
that the honing angle is the same as the grinding angle. Use the bevel colouring method. Hone
away the burr and polish the bevels to a mirror finish.
90
Instructions. Multi Jig, SVS-50.
These tools are manufactured with a skew angle (d) of approx. 25°. You can sharpen your
chisel either with the existing skew angle or you can shape it to a new skew angle of
your choice.
For using this jig the chisel must have a certain min. length, which depends on the edge
angle and the skew angle. At a 25° edge angle and a 25° skew angle the min length of
blade is approx. 105 mm (4 1/8").
The shape of the shank must also be able to be locked in the seat, otherwise use the
open seat, (page 93).
4
P
Mount the tool protruding (P) Mark a line across the stone Put the tool on the Universal
50 - 75 mm (2 - 3") and lock it guided by the Universal Support. Support and turn it until the
with the side screw (4). Use a water proof pen if the bevel is parallel to the line.
stone is wet or a pencil. Tighten the bottom screw (6).
4
P
A scale on the seat enables you Lock the position with the bot- Mount the tool protruding (P)
to set the desired skew angle. tom screw (6). 50 - 75 mm (2 - 3") and lock it
with the side screw (4).
91
Instructions. Multi Jig, SVS-50.
Grindstone condition
Usually carving chisels only need fine sharpening. There-
fore you normally grade the grindstone to a finer grit with
the Stone Grader SP-650. Please see page 122.
When you need to shape the chisel, you use the normal
fast grinding condition of the grindstone.
Grinding
5
Grind the first side. Press with your thumb close to the edge for
the best control. Lift the tool and then move it sideways.
When a burr has developed on the entire edge, turn the jig around
and grind the other side.
92
Instructions. Multi Jig, SVS-50.
Honing
Keep the tool in the jig and move to the leather honing wheel. Set the Universal Support so that the
honing angle is the same as the grinding angle. Use the bevel colouring method. Hone away the
burr and polish the bevels to a mirror finish.
N.B.
If the shank is too tapered, round or otherwise not suitable to allow a proper mounting in
the closed seat, you can use the open seat.
P
5
•
6
Set the desired skew angle and Mount the tool in the jig protrud-
lock the position with the bottom ing approx. 100 mm (4") and
screw (6). lock it with the top screw (5).
93
Instructions. Short Tool Jig, SVS-32.
• Straight gouges
• Straight V tools
Positioning
of the machine Max tool width 32 mm (1 1/4").
Min length of tool 45 mm (1 3/4") at 20° edge
angle.
Tools with a curved shank you grind with the
Grinding direction: SVD-180 jig and gouges wider than 32 mm
away from the edge. (1 1/4") you grind with the SVS-50 jig.
Design
This patented jig was developed for short woodcarving tools, butt chisels and tools for
power carvers. The jig has two parallel flanges running on both sides of the Universal
Support.
The technique achieved with this design ensures that at all times the jig – even when
rotated – holds the tool square to the grindstone. This is a great advantage, as you can
continously concentrate on how the edge touches the grindstone or the honing wheel
without having to worry whether the jig is square to the stone.
45 mm
32 mm 1 3/4"
1 1/4"
94
Instructions. Short Tool Jig, SVS-32.
Carving gouges
Grinding/sharpening/honing or just honing?
As mentioned in the chapter Grinding techniques for carving gouges and V tools on
page 20, you should question whether you should grind the tool or you should go directly
to the honing wheel. This question is especially valid when coping with small and delicate
tools, for which this jig is designed. The small size of the tool, which can be as small as
3 mm (1/8"), also enables the honing wheel to remove small amounts of steel and thus
substitute the grinding.
The following instruction describes the whole process for achieving a sharp edge on a
tool, which has become so blunt that it needs re-grinding. The instruction is also valid for
tools, upon which you want to put a new shape and for tools upon which you want to
change the edge angle.
A tool which is only slightly dull and which has the right shape and edge angle, you
should not grind, but go directly to the honing process (page 97).
Shape the edge by resting the The edge plane angle (g) Flatten and smooth the blunt
tool on the Universal Support should be approx. 20°. edge with the fine side of the
placed horizontally and close to (Page 21). TORMEK Stone Grader, SP-650.
the stone.
95
Instructions. Short Tool Jig, SVS-32.
Edge angle
As described in the chapter Grinding techniques for carving gouges and V tools on
page 24, the choice of edge angle is very important for a carving tool.
The way of setting the edge angle depends on if you want to replicate an existing edge
angle or if you want to put a new edge angle on your tool.
When replicating an existing edge angle, you should use the bevel colouring method,
(page 38). If you want to put a new edge angle to your tool, you can either set the angle
by eye or you can use the Pro AngleMaster, page 40.
When replicating the existing Setting a new edge angle can be done by eye or you can set to a
edge angle you should use the pre-determined edge angle using the Pro AngleMaster (page 40).
bevel colouring method.
Grinding
When you have put the right shape on the tool and set the edge angle, it is time for grinding.
Use the line of light method described on page 20.
Always grind where the line of light is the thickest, while rolling Grade the grindstone for fine
the tool on the Universal Support. Check frequently where the grinding with the fine side of the
grinding takes place. Grind until you get an even and thin line of Stone Grader SP-650.
light.
96
Instructions. Short Tool Jig, SVS-32.
Continue grinding. Check the Remove the burr free-hand on Grind again. Now with a very
result frequently so you do not the leather honing wheel to light pressure. Check frequently
over grind on a spot. observe the line of light more so that you do not over grind on
clearly. The tool is left mounted one spot.
in the jig.
Important!
It is very easy to be misled by the burr and mistake the burr for the line of light! Therefore
you must remove the burr frequently during the finishing of the grinding operation, so you
clearly can watch the progress of a gradually thinning line of light.
Honing
It is important that you hone with the same edge angle as used during the grinding. This is
done by setting the universal support carefully using the bevel colouring method.
Colour the bevel with a marker and mount the tool in the jig. Set Wrong setting. The wheel is hit-
the Universal Support so that the honing wheel touches the entire ting the heel of the bevel. Adjust
length of the bevel. Check with the honing wheel running. the Universal Support away
from the wheel.
97
Instructions. Short Tool Jig, SVS-32.
Wrong setting. The wheel is hit- Correct setting. The honing Prepare both the honing wheels
ting the tip of the edge. Adjust wheel hits the full length of the with honing compound. Please
the Universal Support towards bevel. see page 124.
the wheel.
Sharpen/hone the edge. Roll the Move the jig sideways so you Remove the tool from the jig and
tool on the Universal Support work on the whole width of the hone the inside free hand on the
and apply pressure on the tool leather honing wheel and avoid leather honing wheel.
near the edge. uneven wear on the leather.
V tools
In the chapter of SVD-180 on page 73 it is described how to grind and hone V tools. This
principle is the same when using the SVS-32 jig.
98
Instructions. Short Tool Jig, SVS-32.
Edge angle
a
Wood chisels are usually ground with a 25° edge angle (a).
If you work delicate details with a wood chisel in soft wood,
a
you can decrease the edge angle down to 20°.
If you work in hard wood and when using a mallet, you
must increase the edge angle to 30° or even larger. a
99
Instructions. Short Tool Jig, SVS-32.
Grinding
Press with your thumb close to the edge for best control. You also
control with your hand on the handle that the edge is presented
correctly to the grindstone and not turned. Check frequently so that
you achieve a symmetric edge. Do not slide the jig sideways, but
instead lift it when you move it to another spot on the grindstone.
Honing
Keep the tool in the jig and move to the leather honing wheel. Set Hone the back free hand. Watch
the Universal Support so that the honing angle is the same as the that you do not round the tip.
grinding angle. Use the bevel colouring method. Hold the tool so it is a tangent to
Hone away the burr and polish the bevels to a mirror finish. the wheel.
A square carving chisel. Let the tool handle touch the jig
at both the mountings.
100
Instructions. Tool Rest, SVD-110.
• Carving scorps
• Carving inshaves
• Screw drivers
Positioning
of the machine
Grinding direction:
away from or towards The Horizontal Base XB-100 for
the edge. the Universal Support is required.
Design
This Tool Rest is ideal for the grinding of turning scrapers
and special tools for woodcarving, e.g. large scorps and
inshaves.
It has a generous surface, 90 x 110 mm (3 1/2" x 4 1/4"),
which permits a safe and steady positioning of the tool
towards the stone.
The bore is made with a special wedge shape, which In the patented TORLOCK
increases the locking force by 250 %. You can lock the design, the sides of the tapered
Tool Rest instantly at the chosen angle. This unique bore touch the round bar – not
the bottom. This means that the
design, TORLOCK, is patented by TORMEK.
locking action increases by as
much as 250 %!
101
Instructions. Tool Rest, SVD-110.
Turning scrapers
Scrapers normally come from the manufacturers with an edge angle between 70° and
80°. Some turners prefer a much smaller angle and they re-grind their tools to a 60° edge
angle or even smaller.
Scrapers are best ground towards the edge with the Universal Support in the vertical
position. The rotation of the grindstone helps to press the tool onto the Tool Rest.
At steeper edge angles there is a risk of vibration when grinding towards the edge. If you
want to keep the original large edge angle, you should grind away from the edge with the
Universal Support placed in the Horizontal Base XB-100. Round off the heel of the bevel
and you will reduce the risk that the tool will be pulled up by the stone.
Vertically for edge angles up to approx. 60°. Horizontally for edge angles
larger than approx. 60°.
102
Instructions. Tool Rest, SVD-110.
Edge angle
If you grind a new tool you If you are satisfied with the exist-
should change the edge angle to ing edge angle, set to exactly
60° or less. The Pro Angle- the same angle and the sharp-
Master is an aid to set the Tool ening is completed quickly.
Rest.
103
Instructions. Tool Rest, SVD-110.
Grind towards the edge using Move the Universal Support and Hone away the burr free-hand
the Tool Rest fitted on the Uni- the Tool Rest to the honing on the top face. Hold the tool as
versal Support placed vertically. wheel. Hone the bevel at the a tangent to the wheel.
same angle as at the grinding.
Ticketing
e
Clamp the scraper in your work- Press the gouge on the bevel at You can clearly see how the
bench and press with the HSS an angle (e) of approx. 5°. ticketing compressed the tip of
bowl gouge. Support your left the edge to a smooth and shiny
hand on the bench. surface.
The function of the scraper depends on how large a hook you put on the edge. The size
and shape of the hook depends on the edge angle of the scraper, the ticketing angle (e)
and how hard you press the ticketing tool.
You should not put a too large hook on the scraper, as the tool then is difficult to control
and you can get digs. Remember that you now have a cutting tool instead of a scraper!
Tip:
The jig is made with a large sup-
porting surface for good control
even when grinding long tools.
For short tools, you can trim the
jig surface as necessary to clear
the handle.
104
Instructions. Tool Rest, SVD-110.
Cabinet scrapers
Straight and curved cabinet scrapers are easily squared on the machined outside flat sur-
face of the SuperGrind stone.
Hone away the burr carefully on the Leather Honing Wheel. Create the micro hook using
a burnishing or ticketing tool.
Keep the scraper in close con- Hone away the burr on both Clamp the scraper in your work-
tact with the rest while sliding it sides. Hold the scraper as a bench and press with a hard
back and forth so you use most tangent to the Leather Honing steel rod or burnishing tool along
of the area of the stone. Wheel. the edge to create a micro hook.
Note:
Use a light pressure only at the burnishing and do 5 - 8 strokes. Apply grease or thick oil
so that the rod runs smoothly.
Lock the Universal Support at a Grinding a scorp. Rotate the tool Grinding an inshave. Let as
suitable height. Then set the while you slide it sideways over large a surface as possible
edge angle by adjusting the Tool the stone. remain on the Tool Rest.
Rest.
105
Instructions. Axe Jig, SVA-170.
170 mm
Positioning
of the machine
Grinding direction:
towards the edge.
Design
The jig comprises a clamp with a rubber lined, wedge
shaped stop, which holds the axe in a fixed position
towards the grindstone. The clamp works on the Universal
Support, on which it slides across the stone.
The jig is designed so that the rotation of the stone
presses the axe firmly into the jig. You only need to hold
and guide the axe with your hands. This jig only works
with the stone running towards the edge.
If necessary, the honing wheel can be removed to allow
clearance for the axe handle.
106
Instructions. Axe Jig, SVA-170.
Place the axe into the jig. Set Press with your palm on the axe, Follow the shape of the edge
the edge angle by adjusting the close to the stone. The axe will (straight or curved) during
Universal Support. Either at the automatically be pressed up grinding by raising or lowering
original angle using the bevel against the stop in the jig and the handle. Let the jig slide
colouring method or at a new the grinding is most efficient. sideways on the Universal
angle using the Pro AngleMas- Support so that the stone wears
ter WM-200. evenly.
Edge angle
The edge angle of a carpenters axe or hatchet should be 25° - 30°, depending on the
hardness of the wood. Grind the edge with a smaller bevel angle on the side towards the
wood than on the other side. This longer bevel gives you a good support towards the
wood. Also, as the axe works closer to the surface of the wood, the cutting will be more
effective and easier to control.
A felling axe and a hunting axe must have a larger edge angle, 30° - 40°, so that the
edge is more durable. Round off the bevels and the axe cuts more easily. This is done by
lowering the Universal Support and grinding in two steps.
a a
Put a longer bevel on the wood- A felling axe should have an You can set and measure the
side on a carpenter axe. edge angle (a) of 30° - 40°. edge angle with the Pro Angle-
Round off the bevels and the Master WM-200.
axe cuts more easily.
107
Instructions. Knife Jig, SVM-45.
Suitable for
• Most knives.
Min length
of blade
60 mm (2 3/8")
• Carvers draw
knives
Positioning
of the machine
Grinding direction:
towards or away from
the edge.
Design
The jig comprises an adjustable clamp (1) for holding
knives of any thickness and an adjustable handle (2).
The jig rests on the Universal Support, which is set to an 1 2
approximate height. The exact edge angle is set by turning
the handle.
The Universal Support is normally placed vertically for
grinding towards the edge. Short knives can also be
ground away from the edge with the Universal Support 45 mm (13/4")
placed horizontally. Please see page 113.
108
Instructions. Knife Jig, SVM-45.
Check that the knob is loose. Adjust the jig with the small Tighten the knob. The knife is
screw to fit the thickness of the now firmly mounted in the jig.
knife.
a a a
The edge angle on the tip is depending on where the jig is mount- The correct mounting position
ed on the blade (a). If it is mounted towards the handle, the edge (a) will make the bevel and the
angle at the tip will be smaller. If the jig is mounted towards the edge angle the same along the
tip, the edge angle at the tip will be larger. entire length of the blade.
N.B.
The jig needs to grip the knife with min 2 mm (5/64"). You can grind
knives with a width down to 14 mm (9/16") with an edge angle of
25°. Knives with narrower blades can be ground free-hand. Please
see the chapter Grinding without jigs.
109
Instructions. Knife Jig, SVM-45.
Turn the handle of the jig to zero Set the Universal Support by Make the fine setting of the edge
to be in the middle of the setting eye to approximately the angle by turning the handle
range. desired edge angle. clockwise (+) for a larger angle
and anti-clockwise (–) for a
smaller angle.
You can either grind your knife with the existing edge angle or you can grind a new
angle.
If you want to replicate the existing angle, use the bevel colouring method, (page 38).
If you want to put a new edge angle on your knife, you can use the Pro AngleMaster,
page 40.
When replicating the existing When setting a new edge angle, You can measure the edge
edge angle, use the bevel use the Pro AngleMaster. angle in the grooves of the Pro
colouring method. Please see The angle setter must rest on the AngleMaster.
page 38. bevel.
110
Instructions. Knife Jig, SVM-45.
Thin knives
When setting an edge angle on thin knives the length of
the bevel is very short and it can therefore be difficult to
align it to the angle setter. You can let the angle setter
touch the blade of the knife instead of the bevel. Then the
angle setter should be set to half of the desired edge
angle.
40°
111
Instructions. Knife Jig, SVM-45.
Grinding
Hold the knife and the jig as illustrated. Make sure that you press Grind until a burr forms on the
your thumb (or palm) on the jig so that it is always pressed upper side along the entire
against the back of the Universal Support. Move the knife length of the blade. This you will
slowly back and forth over the stone. Ensure that the blade is in notice by lightly stroking the
contact with the entire width of the stone. Raise the knife handle blade from the back.
when grinding the tip of the knife.
Tip:
Watch how the water flows over the edge to ensure that the blade is in contact with the entire width
of the stone. This is important to achieve an even bevel.
When the first side is ground, turn the jig upside-down – the knife The burr will be weakened and
is still fixed in the jig – and grind the other side. Now the burr more easily removed later if you
appears immediately as it has already developed on the under grind the first side again with a
side. Grind as much as on the first side to obtain a symmetrical light pressure.
edge.
112
Instructions. Knife Jig, SVM-45.
Short knives, which you can mount in the jig up to approx. 50 mm Move the Universal Support to
(2") from the tip (a), can be ground away from the edge. the honing wheel side. Set the
jig so you get the same honing
angle as grinding angle.
Honing
Turn the machine around. Dismount the knife. Hone and polish the You can ensure that the burr is
bevels on the leather honing wheel. Let the entire bevel touch the completely removed by drawing
leather wheel, so you hone at the same angle as at the grinding. the knife through a piece of end
Move the knife back and forth a few times on each side of the grain wood.
blade until the burr disappears.
Important!
Always hone in the direction of rotation (away from the edge). Place the machine as shown with
the wheels running away from you and the honing wheel to the left.
113
Instructions. Knife Jig, SVM-45.
Tips:
• The height of the bench must not be too high when
grinding knives. 550 - 650 mm (20" - 26") is suitable
depending on your height.
Honing
114
Instructions. Long knife Jig, SVM-100.
Suitable for
• Long and thin knives, e.g.
filleting knives.
Min length of blade (a) 120 mm (4 3/4").
• Portable electric
planer blades
Positioning
of the machine
Note:
The height of the bench must not be too high
Grinding direction: when grinding knives. 550 - 650 mm (20" - 26")
towards the edge. is suitable depending on your height.
Design
The jig comprises an adjustable clamp (1) for holding 1 2
knives of any thickness and an adjustable handle (2).
The jig rests on the Universal Support, which is set to an
approximate height. The exact edge angle is set by turning
the handle.
It is made especially for long and thin knives. It works in
100 mm (4")
the same way as the SVM-45 jig but it is wider and there-
fore it gives more support to long and thin blades.
115
Instructions. Scissors Jig, SVX-150.
• scissors
• garden shears
Positioning
of the machine
Design
The jig comprises a support plate (1) and a holder (2) 1
with two clamps for the scissors. Usually you use only the
right clamp. For large scissors and garden shears you use
both clamps. •
•
The clamp is adjustable for any thickness of scissors.
The support plate has a sliding surface, so the holder with
the scissors can easily be moved while it is pressed onto 2
the plate.
116
Instructions. Scissors Jig, SVX-150.
Loosen the larger knob. Adjust the screw so the clamp Ensure that the other blade will
fits the scissor thickness. Leave remain clear of the side of the
about 3 mm (1/8") protruding. stone and tighten the large knob
to hold the scissors in place.
Slide the support plate onto the If you want to repeat the exist- If you want to grind a new edge
Universal Support. Lock the ing edge angle, colour the angle, use the Pro AngleMaster
Universal Support in the lowest bevel with a pen to see where WM-200. Let the indicator touch
possible position with clearance the grinding will take place. the holder between the two
for the plate. clamps.
Grinding
Grind carefully by placing the jig Move the jig back and forth Grind until you have a burr along
on the support plate with a light across the stone while following the entire length of the blade,
downward pressure. the shape of the blade. and you can see an evenly
ground bevel.
117
Instructions. Scissors Jig, SVX-150.
Remove the partially ground Mount the other blade in the jig. Grind the other blade in the
scissors from the jig by loosen- same way as the first one.
ing the large knob.
No honing
Do not hone the edge after grinding! There is no need for a finer surface. As a matter of
fact a coarser surface on the scissors makes them work better, as the material (cloth or
paper) to be cut slides less and cuts more easily.
Remove the little burr resulting from the grinding by drawing the scissors through the end
grain of a piece of wood.
118
Instructions. Grinding without jigs.
Extra short woodcarving skew Large axes and adzes are rest- Hollowing adzes are best
chisels are ground by resting ed on the Universal Support. ground along the edge.
them directly on the Universal Use your index finger as a stop. The Universal Support is placed
Support utilising the shoulder as The Universal Support is placed horizontally for grinding away
a stop. vertically for grinding towards from the edge.
The Universal Support is placed the edge for the most effective
horizontally for grinding away grinding.
from the edge.
Free-hand grinding
With free-hand grinding you grind away from the edge. This direction gives you the best
control as you avoid the risk of the tool digging into the stone. You can also better
observe the grinding process, as no water flows over the edge.
Grinding a wood carving knife. Grinding a pocket knife. Use a This is the best way to grind a
Rest your hands on the Univer- light grinding pressure so that Scythe. As no water flows over
sal Support and keep your fin- the blade does not fold. the edge, it is easy to observe
gers close to the grindstone for First grade the grindstone to fine the burr developing.
best control. grinding with the Stone Grader Hold your elbows close to your
SP-650. body. The honing wheel is
removed.
119
Instructions. Diamond Truing Tool, ADV-50D.
Positioning
of the machine
Turning direction:
towards the tool.
Design
The grindstone is cut with a cluster of diamonds (1)
mounted in a handle (2). The cutting depth is controlled 3
with the stop (3), which is locked with two knobs onto the
Universal Support.
The grindstone is trued exactly round because it is cut in
its working position.
The cutting of the stone is guided by the Universal Sup- 1 2
port, which also guides the jigs. This ensures that the sur-
face of the stone is parallel to the tool fitted in the jig, e.g.
SVH-60 or SVH-320.
120
Preparation
Truing
Start the grindstone. Let the
handle touch the stop with light
pressure, and feed sideways by
pressing the thumb as illustrat-
ed.
Note:
Set and lock the Universal
become fully saturated then stop Support approx. 10 mm (3/8")
the grindstone.
3
1
2
Mount the stop (3) and the
handle (2) on the Universal
Support as illustrated.
• The handle should not be pressed too hard upwards against the stop, to ensure that the
stop is not moved from the pre-set position.
• Do not cut too deeply at a time. If you need to cut more than 0,8 mm (1/32"), repeat the
process, rather than trying to do it in one heavy pass.
121
Instructions. Stone Grader SP-650.
Positioning
of the machine
Note:
For truing a grindstone to an exact round-
ness you must use the Diamond Truing
Tool ADV-50D.
Properties of grindstones
Expressed simply, a grindstone with water cooling can be constructed to grind fast leaving
a coarse surface on the tool or to grind more slowly leaving a finer surface on the tool.
The fast grinding stone is “soft”, which means that the grains are loosely bound. Old, worn
grains can easily leave the stone enabling new fresh and sharp grains to come into opera-
tion. A stone for fine grinding is “harder”, which means that the grains are tightly bound in
the stone. The hard stone wears less than the soft stone.
The TORMEK SuperGrind stone has been specially developed to grind fast while still hav-
ing a long life. The grit is 220. Grindstones with finer grit could be made but then you get
the drawback of a decreased grinding effect and a longer grinding time. You cannot get
both the benefits (fast grinding and the finest surface) in the same grindstone.
One way is to make the first grinding, where the tool is shaped, on a coarse fast grinding
stone and then switch over to a finer and slower grinding stone to achieve a finer surface;
however this way is inconvenient and expensive. Besides that you would need to work
with two stones or possibly two machines and the jig setting would need to be made twice
as the diameter of the two stones would not be exactly the same.
122
Instructions. Stone Grader SP-650.
Grind the tool as usual. The Grade the stone by pressing the
picture shows a plane iron in the fine side onto the stone for
SVH-60 Straight Edge Jig. approx. 15 seconds. Rest your
hands on the Universal Support.
Note:
Do not let the Stone Grader rest directly on the Universal Support as it could wear the
Universal Support. Use the Stone Grader with your wrists resting on the Universal
Support as illustrated.
123
Instructions. Honing and polishing.
Honing wheels
You hone away the burr on the TORMEK honing wheels,
which are made of special leather and then impregnated
with the TORMEK honing compound. The leather removes
the burr gently like the barber’s leather strop, giving you a
razor sharpness and a bevel polished to a mirror finish.
There is a large, flat honing wheel fitted as standard and
as an accessory you can fit a profiled wheel for the inside
honing of gouges and V tools. The profiled honing wheel is an
accessory mounted outside the
standard honing wheel.
When new, impregnate the Apply a thin string of the com- Start the machine and distribute
leather with liquid paraffin (also pound before starting the the compound by pressing a tool
known as mineral oil). This will machine. Rotate the wheel by gently against the wheel.
soften the leather and cause the hand. Let the compound penetrate the
honing compound to penetrate leather.
the leather.
One application lasts for 5-10 tools. Then re-impregnate the honing wheel with a few
drops of oil and apply fresh honing compound. Work the honing compound into the
leather. Do not let the compound dry, apply more oil if necessary.
124
Instructions. Honing and polishing.
Honing
You can hone either free-hand or let the tool remain in the jig after the grinding. Set the
jig so that the honing is carried out at exactly the same angle as the previous grinding.
This is especially advantageous when honing the bevel on gouges where with free-hand
honing it is difficult to exactly follow the shape. The inside is honed free-hand. Honing
must always be carried out away from the edge.
Honing free-hand
The inside on gouges and Honing a long knife. Hold the Honing the back on a plane iron.
V tools are honed on the pro- blade diagonally to clear the
filed wheel. grindstone.
Honing a curved gouge in the SVD-180 jig. Set the Universal Sup- Honing a plane iron in the
port so that you have the same honing angle as the grinding angle. SVH-60 jig.
Honing direction
Always hone away from the If you hone towards the edge, it
edge! cuts into the wheel!
125
Instructions. Honing and polishing.
Note:
The leather honing wheel is made with a strip of leather glued onto a plastic rim. This strip
has a glued joint, which is sanded down at the factory to the surface of the leather. After a
period of use, when the leather has become depressed, the glued joint can remain above
the leather surface. You can easily sand away this thin layer of glue by carefully using
sanding paper mounted on a wooden piece
Polishing
The TORMEK leather honing wheel and honing compound increase the versatility of your
grinder – it will also work as a polishing machine. You can also polish chrome-plated sur-
faces, as well as brass, copper, silver and aluminium to the highest lustre.
126
Grinding methods.
Summary.
127
Recommended grinding method. Summary.
Position of the
Instr.
Tool Grinding jig Universal Support
page
US-100
Wood chisels
SVH-60 Vertically 44
Min length approx 75 mm (3")
Vertically or
Spindle gouges SVD-180 67
horizontally
Scrapers
With edge angles SVD-110 Vertically 102
up to approx. 60°
Scrapers
With edge angles SVD-110 Horizontally 102
over approx. 60°
128
Recommended grinding method. Summary.
Skew chisels
SVS-50 Horizontally 80
Straight or curved
Curved gouges*
SVD-180 Horizontally 68
Up to 25 mm (1") width
129
Recommended grinding method. Summary.
SVS-32 or 94
Straight V tools Horizontally
SVD-180 73
Square chisels
SVS-50 Horizontally 90
Min length approx 100 mm (4")
Square chisels
SVS-32 Horizontally 100
Min length approx 60 mm (2 3/8")
Skew chisels
SVS-50 Horizontally 91
Min length approx 105 mm (4 1/8")
130
Recommended grinding method. Summary.
Carving knives
Vertically or
Min blade length 60 mm (2 3/8") SVM-45 108
horizontally
and min width 14 mm (9/16")
Carving knives - short
Blade length under 60 mm (2 3/8") Free-hand — 119
or width under 14 mm (9/16")
General
Knives Vertically or
SVM-45 108
Min blade length 60 mm (2 3/8") horizontally
Knives
Thin blades longer SVM-100 Vertically 115
than 120 mm (4 3/4")
131
132
Maintenance and tips
133
Maintenance and tips
Reduction gear
The reduction of the rpm from the motor to the grindstone
is achieved by TORMEK’s special friction drive. The more
load you put on the stone, the more the motor shaft is
pressed against the rubberized friction wheel, which pre-
vents any slippage. This design, which is patented in
Sweden, Germany, UK and USA, is simple, reliable and
has an endless life.
The friction wheel should be protected from water, grease
and fine wood dust, which can cause the motor shaft to
slip. Movement of motor shaft
Water trough
Empty and clean the water trough regularly, otherwise
worn particles from the tool and the grindstone will form a
compact mass on the bottom of the trough. Do not put the
residue down your sink. It could congeal and cause prob-
lems with the plumbing.
Tip:
Place a magnet in the water trough to attract the metal
particles. This prevents them from being drawn back up
with the water towards the edge to be ground.
134
Re-activating the stone
The grinding effect of the stone can be reduced if you
grind a hard steel over the whole width of the stone and
with a low pressure (e.g. grinding of a planer blade).
The stone can be re-activated in a few seconds by press-
ing the coarse side of the TORMEK Stone Grader onto
the stone. The old worn grains are removed, thus expos-
ing fresh new ones.
Exchange of stone
The nut has a right handed thread. Loosen and tighten the
nut by using a 19 mm (3/4") wrench. Tap the wrench a few
times with a hammer while you hold the stone.
Important: Do not hold the honing wheel as there is a risk
of damaging the centre of the drive wheel!
We recommend that the stone is changed before it wears
down too much. You should not allow it to be less than
approx. 180 mm (7") in diameter in order to ensure a satis-
factory grinding performance. (The smaller Ø 200 mm (8")
stone should not be less than 150 mm (6")).
It is difficult (in fact impossible) to predict how much grinding can be done or how many
hours a grindstone will last. It depends upon the tools being ground and how much each
tool is ground. As an example, a professional grinder has ground 2000 food knives on the
SuperGrind Ø 250 mm (10") stone, by which time it had worn to 200 mm (8").
If you shape gouges in HSS steel, it wears the stone more quickly. When sharpening an
already shaped tool the stone wear is very limited.
Tip:
• Your old stone can still be used for free-hand work or for very coarse work when grind-
ing special shapes on your tools.
• When shaping a turning gouge, which you normally do only once, quite a lot of steel
needs to be removed. If you do the first, rough shaping on your bench grinder you
reduce wear on the grindstone.
• When grinding a turning gouge to its final shape, which you normally also do only once,
the grinding pressure is high due to the small grinding area, (page 16). This operation
will wear a groove in the stone if the tool is held on the same spot. Therefore you should
ensure that you move the tool sideways across the stone so that you utilize the whole
width and spread the wear of the stone.
135
Maintenance and tips
Bearings
The main shaft runs in special nylon bearings. They are designed to have a radial play of
0,1 - 0,2 mm (0,004" - 0,008"). This has no influence on the running of the stone, as the
load is always downwards. The lifetime is some 1000 hrs and normally they need no re-
greasing. Should however a sound arise, this is cured by re-greasing the bearings.
Remove the stone and pull out the main shaft with the honing wheel and apply grease on
the shaft and in the bearings.
Steel housing
Applying car polish and then drying any remaining water after use will protect the enamel.
136
Maintenance and tips
137
138
The TORMEK
Programme
139
The TORMEK programme
Models
TORMEK offers two models, the SuperGrind 2000 and the SuperGrind
l200 which both use the same range of grinding jigs and accessories.
The SuperGrind 2000 is shown throughout this presentation and this model can handle all
of your grinding and sharpening requirements. Due to the powerful, continuously rated
motor this is the unit which we recommend for grinding HSS woodturning tools and HSS
electric planer blades. It also has the advantage of a convenient carrying handle and a
quick coupling for the instant removal of the honing wheel.
The 1200 SuperGrind is recommended for the grinding and sharpening of hand tools
including woodcarving tools.
Of technical reasons the 1200 model is not available for 115 V ~60 Hz.
SuperGrind SuperGrind
2000 l200
140
The TORMEK programme
Grinding Jigs
For plane irons, wood chisels and spoke shave
blades. 0,20 kg
Straight Edge Jig
(Supplied as standard with the machine.) 0,44 lbs
141
The TORMEK programme
Accessories
Stone Grader
Profiled Leather
Honing Wheel
Machine cover
Spare accessories
Pro AngleMaster
Honing Compound
Trues the stone exactly round and flat.
0,40 kg
0,88 lbs
0,37 kg
0,82 lbs
0,09 kg
0,20 lbs
0,15 kg
0,33 lbs
0,063 kg
0,14 lbs
0,09 kg
0,20 lbs
PAL
“The TORMEK method of grinding, sharp- 0,16 kg
NTSC
ening and honing edge tools” 23 min. 0,36 lbs
Instruction Video
142
The TORMEK programme
143
144
32
24
7
15
22
11
41
47
44
44
46
18 2
47 21
44
The TORMEK programme
SuperGrind 2000
Item Weight
No. Denomination Quantity kg/each
1 Grindstone SuperGrind 1 4,90
2 Housing 1 3,40
4 Drive wheel with friction ring 1 0,26
5 Honing wheel 1 0,38
7 Water trough 1 0,20
8 Mounting shaft 1 0,08
9 Handle incl. nut and washer 1 0,062
10 Main shaft 1 0,34
11 Motor, 200 W 1 3,20
15 Cover for switch 1 0,03
16 Nylon bearing 2 0,003
18 Rubber foot 4 0,005
20 *Machine label 1 0,002
21 Cord set 1 0,20
22 Cord set bushing 2 0,003
24 Switch 1 0,020
29 Washer for the stone 2 0,027
30 Washer for the drive wheel 1 0,006
31 Nut, M12 h=6 1 0,015
32 Screw for cover 2 0,002
39 Locking pin 1 0,001
41 Screw 1 0,003
44 Nut (brass) 3 0,001
46 Folded washer 1 0,002
47 Locking washer 2 0,001
50 Locking knob for honing wheel 1 0,023
51 Nut, M12 h=4 1 0,012
54 Sleeve 2 0,14
55 Locking knob 3 0,01
56 Nut for sleeve 2 0,021
59 Universal Support 1 0,52
60 *Carton, complete 1 1,00
61 *Distance sleeve for the motor 1 0,003
62 Horizontal Base 1 0,102
63 Screw 4 0,003
64 Locking screw 1 0,009
* = Not shown on drawing. 145
146
15
41 32 21
44
42
44
41
46
23
47 44 18
2
3 11
33
The TORMEK programme
SuperGrind 1200
Item Weight
No. Denomination Quantity kg/each
1 Grindstone, SuperGrind 1 2,60
2 Housing 1 0,50
3 Grating 1 0,070
4 Drive wheel with friction ring 1 0,045
5 Honing wheel 1 0,11
7 Water trough 1 0,085
8 Mounting shaft 1 0,035
10 Main shaft 1 0,31
11 Motor 120 W 1 2,40
15 Cover for switch 1 0,03
16 Nylon bearing 2 0,003
18 Rubber foot 4 0,002
20 *Machine label 1 0,002
21 Cord set 1 0,20
23 Strain relief 1 0,001
24 Switch 1 0,020
29 Washer for the stone 2 0,027
30 Washer for the drive wheel 2 0,006
31 Nut, M12 h=6 2 0,015
32 Screw for cover 2 0,002
33 Screw for grating 4 0,002
39 Locking pin 1 0,001
41 Screw 3 0,003
42 Nut for strain relief 2 0,001
44 Nut (brass) 3 0,001
46 Folded washer 1 0,002
47 Locking washer 1 0,001
55 Locking knob 2 0,01
58 Ring for Universal Support 2 0,015
59 Universal Support 1 0,52
60 *Carton, complete 1 0,60
62 Horizontal Base 1 0,102
63 Screw 4 0,003
64 Locking screw 1 0,009
* = Not shown on drawing
147