Switch features 3 Independent

positive drive mechanisms and Conformity

IP 67 Rated S.P.D.T Change-over
Yellow trip indication flag
Safety Micro Switches with Direct and plastic pull wire set
Opening Action for high safety up gauge supplied with
all switches.
performance, enclosed in an IP
66/67 flame retardant high impact
enclosure.

Testtoed
IP 66/67
The Pull Wire Switch has been tested to the requirements of IEC 60947-5-5 and AS4024.
Tripping occurs under the following conditions:–
(a) One or both trip wires are removed or cut/broken (c) One or both trip wires are activated
(b) One or both trip wires are overtensioned (d) Manual trip via reset knob.
The switch cannot be reset unless both trip wires are attached and correctly tensioned,
Manual reset via the external reset knob is required after a trip has occurred.

FEATURES
• Tamper Proof Switch Plate Mechanism.
• Every Switch is individually, electrically and mechanically tested with Test Certificates available.
• Absolute simplicity in initial setup and adjustment. All Set Point adjustments are done from the outside of the
enclosure.
• UV stable high impact robust non-metallic enclosure.
• Simple design ensures low maintenance.
• Stainless steel internal compression type springs.
• Electro polished 316 stainless steel pull rods and mounting feet.
• Pull rods have spring loaded external dust protecting boots so the pull rod is always covered for extra seal protection
and pull rods are not exposed to contaminates.
• Double lip oil seals on pull rods and reset operator for secure dust and weather protection to IP 66 / 67.
• Non-metallic pull rod bushings so no electrolysis issues between the safety mechanism (pull rod) and bushing.
Increasing functional safety.
• Independent positive drive pull rod cams, switch plate mechanism and lid drive cam for 3 fail safe trip mechanisms to
ensure the switch will trip and fail to safe.
• Complies to IEC 60947-5-1 Ed 3.1 AS/NZS 60947-5-1:2015 IEC 60947-5-5 Ed 1.1
AS/NZS 60947.5.5:2015 AS/NZS 4024.1-2014 AS/NZS 4024.3610:2015
AS/NZS 4024.3611:2015
• Internal switch connections are fully shrouded for added safety during inspection.
• IP 67 S.P.D.T Change-over Safety Micro Switches with Direct Opening Action (IEC 60947-5-1 Annex K) in contact
element form C tested and passed too IEC 60947-5-1.
• Cam design compensates for pull wire expansion/contraction up to 30mm either side of the set point. Eliminates
nuisance tripping due to vibration.
• Pull forces to actuate trip @ 60Nm (6Kg) 90° to pull wire axis and 90Nm (9Kg) along pull wire axis.
• Cam position signal sensing before tripping.

PULL WIRE SWITCH

 VARIATIONS REMOTE END
• Max 4 IP 67 S.P.D.T Change-over Safety Micro Switches • Matched stainless steel compensation springs
with Direct Opening Action in contact element form C, for remote end attachment. P/N STP-E60.
• External signal flag (Note: Comes with Switch), To comply with safety critical functions
• External light, AS/NZS 4024.3610 -2015 section 2.10.5
• Single sided operation, right hand or left hand, Emergency Stop. A matched compensation
• Two x M20 stainless steel armoured cable glands. spring must be fitted to the remote end of the
Pull Wire to allow tripping in both directions.

INSTALLATION SWITCH SETTINGS

One centrally mounted switch for every 200m Switch setting is via a turnbuckle from the
of pull wire. Consult STP-P Safety, Installation, Design and outside of the switch. No internal access needed
Setting Instruction sheet for recommendations. to adjust to set point.

DIMENSIONS
171
50 267
120

61

EMERGENCY STOP
SET

200 175
TRIP

114

RESET ELECTRIC CONTROL PRODUCTS

MADE IN AUSTRALIA

100 ø 9.0 Mounting

Holes x 4

ORDERING DETAILS ENCLOSURE SPECIFICATIONS

Standard Switch with 316 Stainless Steel mounting • High Impact PBT/PC - Non Corrosive Material.
feet and 2 IP 67 rated S.P.D.T Safety Micro with • U.V Stabilised. (See Plastic Specs Sheet)
Direct Opening Action ............................................STP-P-2 • Flame retarded ASTM.UL94.V-0 (1.6mm)
Standard Switch with 316 Stainless Steel mounting • Resists splash and spillage of most hydrocarbon solvents,
feet and 4 IP 67 rated S.P.D.T Safety Micro mild acids and strong alkali. (See Plastic Specs Sheet)
Switches with Direct Opening Action ....................STP-P-4
ENCLOSURE SPECIFICATIONS
Add to above Cat No. for variations: IP 67 Safety Micro Switch with Direct Opening Action Specifications
External strobe light ..................................... -S number ................. IEC 60947-5-1 Annex K classification ■ Type 1 ■
X Type 2 Direct Opening
S2 = Red Strobe for 10 – 100V DC 20 – 72V AC Current Use 130-37mA @ Flash Rate = 75fpm Change-over contact element ■
XC ■ Za ■ Zb
S3 = Red Strobe for 90 -125V AC Current Use 30mA @ Flash Rate = 60fpm Contact material Ag-Ni
S4 = Red Strobe for 207 – 253V AC Current Use 15mA @ Flash Rate = 60fpm Utilization category AC-15 DC-13
S6 = Amber Strobe for 10 – 100V DC 20 – 72V AC Current Use 130-37mA @ Flash Rate = 75fpm Operational voltage 230 V 60 V
S7 = Amber Strobe for 90 -125V AC Current Use 30mA @ Flash Rate = 60fpm Operational current 1,5 A 0.5 A
S8 = Amber Strobe for 207 – 253V AC Current Use 15mA @ Flash Rate = 60fpm Frequency 50/60 Hz ——
Number of electrical cycles 6050 (6 min-1)
Left hand operation only................................................................ -LH Number of mechanical cycles 6050 (6 min-1)
Conventional free air thermal current 10 A
Right hand operation only .......................................................... -RH Conventional enclosed thermal current ——
Two x M20 stainless steel Operating Temperature -35° C No Icing +80° C
armoured cable glands sockets ......................................... -ACGS Specifications (short-circuit with standability)
Rated conditional short-circuit current 3 00 A 1 000 A
Matched SS Compensation Spring ....................... STP-E60 Short circuit protective device Fuse 6 A gG (IEC 60269-2) Fuse 6 A gR (IEC 60269-4)
DEL: CB001 01/21

Manufactured in
Australia by: Sold by:

18 Tambrey Way, Malaga

Western Australia 6090
PUB. No. STP – P

Telephone: (08) 9247 6700

Facsimile: (08) 9248 6292 www.safe-t-products.com.au

PULL WIRE SWITCH