FSK-628D Gobernador Electronico de Motor
FSK-628D Gobernador Electronico de Motor
Controls
Operation Instruction
Contents
1. Overview……………………………………………………………1
2. Main Technical Parameters…………………………………………2
3. Composition and work principle…………………………………3
4. Fundamental Function………………………………………………4
5. Controller installation and debugging……………………………8
5.1 Controller installation…………………………………………8
5.2 Controller Parameter Tuning…………………………………9
5.2.1 Controller wiring diagram………………………………9
5.2.2 First time start-up…………………………………………9
5.2.3 Parameter adjusting………………………………………13
5.2.4 Condition tuning…………………………………………19
5.2.5 Factory setting……………………………………………21
5.2.6 Caution Note for Tuning…………………………………26
6. Guideline for Controller Breakdown Maintenance……………24
6.1 Routine trouble shooting……………………………………25
6.2 Special fault diagnosis list…………………………………26
FSK628D Engine Electronic Governor Operation Instruction
1 Overview
0
FSK628D Engine Electronic Governor Operation Instruction
0
FSK628D Engine Electronic Governor Operation Instruction
0
FSK628D Engine Electronic Governor Operation Instruction
4 Fundamental Function
0
FSK628D Engine Electronic Governor Operation Instruction
0
FSK628D Engine Electronic Governor Operation Instruction
0
FSK628D Engine Electronic Governor Operation Instruction
0
FSK628D Engine Electronic Governor Operation Instruction
0
FSK628D Engine Electronic Governor Operation Instruction
sharp pounding vibration and/or EMI, and had has sufficient space for
installation, maintenance and heat rejection. Its housing must be of reliable
earthing. Erect installation can prevent from too much moisture resident.
Installation dimension of speed governor is shown in fig. 2.
5.2 Controller Parameter Tuning
5.2.1 Controller wiring diagram
0
10
FSK628D Engine Electronic Governor Operation Instruction
about major failures such as engine speed unsteady, over speed and so
on.
◦ Inspect whether the related electrical connections are correct according
to fig. 2.
◦ Inspect actuator for movement flexibility. After confirmation of
connection agility, recheck if the fuel rack’s least position can make
fuel(air) cutoff and if the fuel rack’s maximum position can make
fuel(air) quantity maximum.
◦ Inspect battery voltage. When no-load, it should be greater than 24 V.
When engine starts, it should be not less than 18 V. When the controller
was powered on, the red LED indicator light on the controller panel will
be light.
◦ Inspect the parameter setting device’s position compared with their
factory set show in 5.2.5. If every parameter setting device’s position is
12
FSK628D Engine Electronic Governor Operation Instruction
much different from their factory set before starting engine, user must
reset them to factory set. This can avoid failures such as can not start-up
or over speed etc.
5.2.3 Parameter adjusting
13
FSK628D Engine Electronic Governor Operation Instruction
14
FSK628D Engine Electronic Governor Operation Instruction
Turn high and low speed switches to low-speed positions until the
engine could be placed in idle speed condition.
Adjust low speed potentiometer to demanded idle speed. Then
anticlockwise adjust start fuel quantity potentiometer until engine speed
begin dropping, then turn the potentiometer back forward until idle
speed stability.
Let engine shutdown. Restart the engine. If it is difficult to start-
up, increase the start-up fuel quantity.
Start-up fuel quantity is influenced by the surrounding temperature.
In order to make engine easy starting up in every kind of weather. Fuel
potentiometer should be set at the increased position.
◦ Raising speed time adjustment
User can tune raising speed time potentiometer as required
todetermining required raising time from low speed to rated speed.
15
FSK628D Engine Electronic Governor Operation Instruction
Anticlockwise rotate for time shorten; and clockwise rotate for time
expanding. While working, this time can be annually adjusted between
1.5 to 40 seconds.
◦ Stability Adjusting
The order of stability adjusting is low speed, high speed and rated
load, all these three state achieve stability.
Stability adjusting mainly through adjusting gain、
differential(stability adjusting) potentiometer. Gain potentiometer
is used for adjusting the sensitivity of system. Clockwise regulate
for increasing flexibility and anticlockwise regulate for decreasing
flexibility. Differential (stability adjusting) adjusting potentiometer
is used to adjust the respond time of system. Clockwise regulate
for increase velocity of respond time and anticlockwise regulate for
decrease. After gain and differential(stability) adjusting, engine’s state
16
FSK628D Engine Electronic Governor Operation Instruction
17
FSK628D Engine Electronic Governor Operation Instruction
18
FSK628D Engine Electronic Governor Operation Instruction
19
FSK628D Engine Electronic Governor Operation Instruction
= OFF, SW1-2 =ON. This condition is suitable for the engine without
fast wild effect.
SW1-1, SW1-2 = ON,SW1-3 =OFF. This condition is
suitable for the engine with fast wild effect.
So-called fast instability namely speed-rise, frequency instability
increase quickly, vice versa slow down. Normally, through choose in
these two condition, diesel engine under medium can achieve ideal
stable and dynamic character.
and SW1−1, SW1−2 = OFF, SW1−3 = ON and SW1−1,
SW1−3=ON,SW 1−2=OFF. This condition is suitable for fast precarious
occasion owing to elastic fixing for engine and generator. It can match with
diesel engines under medium.
Specially, if after the forgoing adjustment, especially on load,
demandedstability still can not achieved, the difference time of the controller
20
FSK628D Engine Electronic Governor Operation Instruction
21
FSK628D Engine Electronic Governor Operation Instruction
22
FSK628D Engine Electronic Governor Operation Instruction
23
FSK628D Engine Electronic Governor Operation Instruction
24
FSK628D Engine Electronic Governor Operation Instruction
25
FSK628D Engine Electronic Governor Operation Instruction
26
FSK628D Engine Electronic Governor Operation Instruction
27
FSK628D Engine Electronic Governor Operation Instruction
28
FSK628D Engine Electronic Governor Operation Instruction
29
FSK628D Engine Electronic Governor Operation Instruction
30
DA TONG YUN SI DA TECHNOLOGY CO.,LTD
Address: 7 Daqing East Road, Datong City, Shanxi Province, PRC
Post code:037038
Contact telephone:(86) 0352–5099489 5090023
Fax: (86) 0352–5099521
http://www.ysd2000.com
Email: [email protected]