TM 43-0001-39 (Cads)

TM 43-0001-39
TECHNICAL MANUAL
ARMY DATA SHEETS

FOR
CARTRIDGES,
CARTRIDGE ACTUATED DEVICES
AND
PROPELLANT ACTUATED DEVICES
FSC 1377
Approved for public release: distribution is unlimited.
HEADQUARTERS, DEPARTMENT OF THE ARMY

DECEMBER 1991
THE SQUIB SHALL NOT BE EXPOSED TO SOLVENTS OR

ACIDS. THEY SHALL NOT BE SUBJECTED TO SEVERE
SHOCK OR JAR WHICH MIGHT BREAK THE BRIDGE WIRE
RENDERING THE SQUIB INOPERATIVE.
TO PREVENT DISCONNECTED SQUIBS FROM FIRING
BARE ENDS OF LEAD WIRES SHALL BE TWISTED
TOGETHER SO THAT THEY ARE IN FIRM CONTACT WITH
ONE ANOTHER.
THIS ELECTRIC SQUIB SHALL NOT BE RESISTANCE
CHECKED EITHER PRIOR TO OR AFTER INSTALLATION
IN THE DEVICE OF INTENDED APPLICATION.
TM 43-0001-39
C2
Change
No. 2
HEADQUARTERS
DEPARTMENT OF THE ARMY
Washington, DC, 30 June 1994
)
)
)
TECHNICAL MANUAL
ARMY DATA SHEETS
FOR
CARTRIDGES, CARTRIDGE ACTUATED DEVICES
AND
(FSC 1377)
TM 43-0001-39, 20 December 1991, is changed as follows:
1.
Remove old pages and insert new pages as indicated below. New or changed material is indicated
by a vertical bar in the margin of the page. Added or revised illustrations are indicated by a vertical
bar adjacent to the identification number.
2.
Remove pages
Insert pages
A and B
i thru iv
5-99 thru 5-102
A and B
i thru iv
5-99 thru 5-102
File this change sheet in front of the publication for reference purposes,
By Order of the Secretary of the Army:
GORDON R. SULLIVAN
General, United States Army
Chief of Staff
Official:
MILTON H. HAMILTON
Administrative Assistant to the
Secretary of the Army
06338
DISTRIBUTION:
To be distributed in accordance with DA Form 12-34-E, Block 0933, Requirements for TM 430001-39.
TM 43-0001-39
C1
Change
No. 1
HEADQUARTERS
Washington, DC, 1 March 1994
)
)
)
TECHNICAL MANUAL
ARMY DATA SHEETS
FOR
CARTRIDGES, CARTRIDGE ACTUATED DEVICES
AND
(FSC 1377)
TM 43-0001-39, 20 December 1991, is changed as follows:
Remove old pages and insert new pages as indicated below, New or changed material is indicated
1.
by a vertical bar in the margin of the page. Added or revised illustrations are indicated by a vertical
bar adjacent to the identification number.
2.
Remove pages
Insert pages
A
i and ii
3-3 and 3-4
none
A and B
i and ii
3-3 and 3-4
3-4.1 and 3-4.2
File this change sheet in front of the publication for reference purposes.
GORDON R. SULLIVAN
Chief of Staff
Official:
MILTON H. HAMILTON
06266
DISTRIBUTION:
To be distributed in accordance with DA Form 12-34-E, Block 0933, Requirements for TM 430001-39.
TM 43-0001-39
When applicable, insert latest change pages and dispose of

superseded pages in accordance with applicable regulations.
TOTAL NUMBER OF PAGES IN THIS PUBLICATION IS 231

CONSISTING OF THE FOLLOWING:
Page
No.
Cover
Inside cover
A
B
i
ii.. .
111
iv
1-1 and 1-2
2-1
2-2 blank
2-3 thru 2-12
3-1
3-2 blank
3-3 and 3-4
3-4.1 and 3-4.2
3-5 thru 3-12
4-1
4-2 blank
4-3 thru 4-8
5-1 thru 5-98
5-99 thru 5-102
5-103 thru 5-109
5-110 blank
6-1
6-2 blank
*Change
No.
0
0
2
1
2
0
2
0
0
0
0
0
0
0
1
1
0
0
0
0
0
2
0
0
0
0
Page
No.
6-3 thru 6-15
6-16 blank
6-17 thru 6-28
7-1
7-2 blank
7-3 thru 7-6
8-1
8-2 blank
8-3 and 8-4
9-1
9-2 blank
9-3 thru 9-8
10-1
10-2 blank
10-3 thru 10-8
A-1 and A-2
B-1 thru B-6
C-1 and C-2
D-1 and D-2
E-1 thru E-3
E-4 blank
F-1 and F-2
G-1 thru G-3
G-4 blank
H-1 and H-2
Authentication page
*Change
No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
* Zero indicates an original page.
Change 2
TM 43-0001-39
THIS PAGE INTENTIONALLY LEFT BLANK
B Change 1
TM 43-0001-39
Technical Manual
No. 43-0001-39
)
)
)
HEADQUARTERS
Washington, DC, 20 December 1991
ARMY DATA SHEETS
FOR
CARTRIDGES,
CARTRIDGE ACTUATED DEVICES
AND
REPORTING OF ERRORS
You can help improve this manual. If you find any mistakes or if you know of a
way to improve the procedures, please let us know, Mail your letter, DA Form
2028 (Recommended Changes to Publications and Blank Forms) to Commander,
US. Army Armament Research, Development and Engineering Center, ATTN:
SMCAR-LSB, Picatinny Arsenal, NJ 07806-5000. A reply will be furnished
directly to you. Comment or questions concerning individual items must be
addressed to the cognizant field activity at Naval Ordnance Station, ATTN:
Code 5320C, Indian Head, MD, 20640-5000. Also see Chapter 1, para 1-1.d.
Page
CHAPTER 1
CHAPTER 2
CHAPTER 3
CHAPTER 4
INTRODUCTION
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .
DOT Shipping Class and Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reference Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-2
1-2
1-2
CARTRIDGES, AIRCRAFT FIRE EXTINGUISHER

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge, Aircraft Fire Extinguisher: (M182) . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge, Aircraft Fire Extinguisher: (M193) . . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge, Aircraft Fire Extinguisher: (M232) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge, Aircraft Fire Extinguisher, CCU-90/A: (MH92) . . . . . . . . . . . . . . . . . . . . . .
Cartridge, Aircraft Fire Extinguisher: (MT20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-3
2-5
2-7
2-9
2-11
CUTTERS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutter, Cartridge Actuated: M21 (M500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutter, Cartridge Actuated: M22 (M504) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutter, Cartridge Actuated: (M554) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutter, Cartridge Actuated: P/N 3031-4-1 (MU02) . . . . . . . . . . . . . . . . . . . . .
Cutter, Assembly P/N FTL3648-2 (MU03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutter, Delay, Propellant Actuated: (MU11) . . . . . . . . . . . . . . . . . . . . . . . .
3-1
3-3
3-4.1
3-5
3-7
3-9
3-11
TIME DELAY CARTRIDGES

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge, Delay: CCU-57/B, (MF35) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge, Delay: CCU-89/B, (MH88) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge, Delay: (M308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-3
4-5
4-7
*This manual supersedes TM 43-0001-39, 28 November 1985, including all changes.
Change 2 i
TM 43-0001-39
Page
CHAPTER 5
SECTION I - EMERGENCY ESCAPE SYSTEMS FOR HELICOPTER;

AH-1 SERIES (COBRA)
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cord, Detonating, Assembly Flexible Confined (FCDC) (Gunner):
(MD15) . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cord, Detonating, Assembly Flexible Confined (FCDC) (Pilot):
(MD16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cord Detonating, Assembly Shielded Mild (SMDC): (MD17) . . . . . . . . . . . . .
Cord Assembly Detonating, Shielded Mile (SMDC): (MD18) . . . . . . . . . . . . . . . . .
Cutting Assembly Window (WCA): (MD33) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutting Assembly Window (WCA): (MD34) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutting Assembly Window (WCA): (MD35) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutting Assembly Window (WCA): (MD36) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cord, Detonating, Assembly Shielded, Mild (SMCD): (MS47) . . . . . . . . . . . . . .
Cord, Detonating, Assembly Shielded, Mild (SMCD): (MS48) . . . . . . . . . . . . . . . .
Cord, Detonating, Assembly Shielded, Mild (SMCD): (MS49) . . . . . . .
Cord, Detonating, Assembly Shielded, Mild (SMCD): (MS50) . . . . . . . . . . . . . . .
Cord, Detonating, Assembly, Shielded, Mild (SMCD): (MS55) . . . . . . . . . . . . . . . .
Cord, Detonating, Assembly Shielded, Mild (SMCD): (MS59). . . . . . . . . . . . . . .
Cord, Detonating, Assembly, Shielded, Mild (SMCD): (MS61) . . . . . . . . . . . . . . .
Linear Explosive Assembly (LEA): (MS76) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Linear Explosive Assembly (LEA): (MS77) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Linear Explosive Assembly Window (WCA): (MS78) . . . . . . . . . . . . . . . . . . . .
Linear Explosive Assembly Window (WCA): (MS79) . . . . . . . . . . . . . . . . . .
Inert Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION II - EMERGENCY ESCAPE SYSTEMS FOR HELICOPTER;
AH-64 SERIES (APACHE)
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cord, Detonating, Assembly, Flexible Confined (FCDC): (MS89) . . . . . . . . . .
Cord, Detonating, Assembly Flexible Confined (FCDC): (MS90) . . . . . . . . . . .
Cord, Detonating, Assembly, Flexible Confined (FCDC): (MS91) . . . . . . . . . . .
Cord, Detonating, Assembly, Flexible Confined (FCDC): (MS92) . . . . . . . . . . .
Cord, Detonating, Assembly, Flexible Confined (FCDC): (MS93) . . . . . . . . . .
ii
5-1
5-9
5-11
5-13
5-15
5-17
5-19
5-21
5-23
5-25
5-27
5-29
5-31
5-33
5-35
5-37
5-39
5-41
5-43
5-45
5-47
5-49
5-51
5-53
5-55
5-57
5-59
5-61
5-63
5-65
5-67
5-71
5-73
5-75
5-77
5-79
5-81
5-83
5-85
5-87
5-89
5-91
5-93
5-95
5-97
TM 43-0001-39
CHAPTER 5
Page
SECTION II - Continued
Canopy Severance Assembly, Forward Panel: (MS94) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-99
Canopy Severance Assembly Rear (Aft) Panel: (MS95) . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-101
Canopy Severance Assembly Rear (Aft) Panel: (MS96) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-103
Canopy Severance Assembly Forward Panel: (MS97) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-105
Arming/Firing Initiator, JUA-59: (MT06) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-107
Inert Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-109
CHAPTER 6
IMPULSE CARTRIDGES
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Cartridge, Impulse, Mk 19 Mod 0: (MO12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Cartridge, Impulse: (M162) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
Cartridge, Impulse: ARD 863-1 (M189) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Cartridge, Impulse: (M253) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Cartridge, Impulse, Mk 104 Mod 0: (M291) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Cartridge, Set, Impulse, Reduced Charge Primary: (M397) . . . . . . . . . . . . . . . . . . . . 6-13
Cartridge, Impulse, Drogue: (M507) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
Cartridge, Impulse, Guillotine: (M520) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
Cartridge, Impulse: (M657) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21
Cartridge, Impulse, CCU-92/A: (MJ21) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
Cartridge, Impulse: (MD73) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25
Cartridge, Impulse, CCU-44/B: (MD66) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27
CHAPTER 7
INITIATORS/DETECTORS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Arming/Firing Mechanism: P/N 813633-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Arming/Firing Mechanism: P/N 814033-101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
CHAPTER 8
ROCKET MOTORS/CATAPULTS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Rocket Motor: M447 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
CHAPTER 9
THRUSTERS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Thruster, Cartridge Actuated, TCU-1/B: (MF24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Thruster, Cartridge Actuated, TCU-3/A: (MJ20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
Thruster, Explosive Actuated: P/N 209-033-007 -3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
CHAPTER 10
MISCELLANEOUS ITEMS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Refire Kit: 073-3831 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Pin Puller, Explosive Actuated: P/N 816984 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
Cartridge Assembly, Cargo Hook: PY58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
APPENDIX A
REFERENCE PUBLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
APPENDIX B
CAD/PAD AIRCRAFT/HELICOPTER/EQUIPMENT CROSSREFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
APPENDIX C
AIRCRAFT/HELICOPTER/EQUIPMENT CAD/PAD CROSSREFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX D
C-1
CAD/PAD INDEX BY DODIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Change 2 iii
TM 43-0001-39
APPENDIX E
CAD/PAD INDEX BY NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
APPENDIX F
CAD/PAD INDEX BY GOVERNMENT SOURCE DRAWING NUMBER . . . . F-1
APPENDIX G CAD/PAD INDEX BY MANUFACTURERS PART NUMBER . . . . . . . . . . . . . . . . . . . . . G-1

APPENDIX H CAD/PAD INDEX BY NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1
Authentication Page
iv
TM 43-0001-39
CHAPTER 1
INTRODUCTION
1-1. Purpose
a. This manual is a reference handbook
published as an aid in planning, training, and
identification of Cartridges/Cartridge Actuated
Devices (CADS) and Propellant Actuated
Devices (PADs). It is not to be used as authorization for requisitioning, stockage, maintenance, or issue of this materiel.
b. The CADs/PADs data sheets in this
manual are arranged by chapters according to
their characteristics. Each data sheet uses the
item nomenclature as its title, In most cases, a
DODIC (in parentheses) will follow the item
name,
References and cross-references are
located in Appendix A thru Appendix H.
c. Throughout this manual, the term
CAD shall be synonymous with and collectively
represent FSC 1377 cartridges, cartridge actuated devices, and explosive detonating cords
used in aircraft/helicopter emergency escape systems, fire extinguisher systems, and equipment/ stores jettison and separation systems.
The term PAD shall be synonymous with and
collectively represent FSC 1377 rocket catapults and rocket motors used in aircraft escape
systems.
d. The Naval Ordance Station
(NAVORDSTA), Indian Head, MD 20640-5000
(Code 5320C) has been designated as the
Cognizant Field Activity (CFA) for CADS and
PADs.
Any questions concerning the
CADs/PADs described in this publication should
be directed to this station, Code 5320C.
1-2. Scope
a. This manual contains descriptive and
technical data for 1377 class CADS and PADs
used by the Army For each CAD/PAD, there
are illustrations, descriptions, and technical
data related to the CAD/PAD use, characteristics, shipping and storage, and function, plus a
list of reference publications,
b. Service life is the period of time a
CAD/PAD can be issued and used with an
ensured high degree of reliability, Performance
of CADs/PADs is influenced by the environment
to which they are exposed (e.g., temperature,
humidity vibration, shock). For current data
on Service life (Shelf & Installed), refer to
Appendix B of TB 9-1300-385. Updates to the
TB are issued quarterly.
c. Shelf life is the period of time, beginning from date of manufacture, that a
CAD/PAD can remain in its hermetically-sealed
container and still be serviceable. Shelf life is
always computed from date of manufacture
available from the lot number.
d. Installed life is the period of time a
CAD/PAD is allowed to be used after its hermetically-sealed container is opened, The installed
life expiration date shall never exceed the shelf
life expiration date as established from the date
of manufacture,
e. The shelf life and installed life are the
maximum approved limits established for Army
use. TB 9-1300-385 shall be consulted prior to
installing any CAD/PAD and for periodic inspections of installed CADs/PADs to ensure the lots
installed in operational Army aircraft/helicopters/equipment have not been suspended or
restricted from use.
f. In the event of differences concerning
the shelf lives and installed lives, TB 9-1300385 shall take precedence,
g. CAD/PAD shelf lives and installed
lives are not to be combined. A CAD/PAD is
over age is either of these limits is exceeded.
h. Information concerning supply operation, safe handling, and maintenance of these
devices can be found in TM 9-1377-200-20&P.
i. Included for the devices in this manual are the Type Classification and Logistics
Control Code (LCC). Devices with the following type classifications are included:
(1) Standard (LCC-A, LCC-B)
(2) Contingency (CON)
(3) Limited Procurement
(4) Reclassified Obsolete (OBS) for regular Army use, but used by National Guard or
Reserve Limits.
(5) Reclassified OBS for all Army use
but used by Marine Corps, Air Force, or Navy.
(6) Reclassified OBS, no uses, but US
stocks remain.
1-1
TM 43-0001-39
(7) Reclassified OBS for all US use;

no US stocks remain (foreign use or stock may
remain).
j. Numerical values, such as weights,
dimensions, etc., are nominal values except
when specified as minimum or maximum limits. Actual values may vary slightly from these
values due to established tolerance limits.
Allowable tolerance limits can be obtained from
the drawings indicated in the data sheets.
k. The FSCM is now replaced by CAGE
(Commercial and Government Entity) Code in
the Tabulated Data section of data sheets.
1.3. DOT Shipping Class and Designation
The DOT classification changed effective
21 December 1990. Users of this manual must
consult the Joint Hazard Classification System
(JHCS) for Ammunition and Explosives
(updated quarterly) for DOT Hazardous
Materials Description (Proper Shipping Name)
and Identification Number (United Nations
Serial Number) for each item herein. This data
is advisory only for shipments between Depots,
user storage, and user facilities. Data in the lat-
1-2
est issue of the JHCS will always take precedence unless written authorization to the contrary is obtained from the PICA (AMCCOM
Attn: DRSMC-DSD-AS (R), Rock Island, IL
61299). Additional data on this matter is currently being developed and will be incorporated
in future changes to this manual as it becomes
official.
1-4. Disposal
Disposal of CADs/PADs determined to be
in a hazardous, damaged, or overaged condition
is the responsibility of Explosive Ordnance
Disposal (EOD) personnel, A CAD/PAD may
only be disassembled by EOD personnel in
order to render the unit safe. No other disassembly is authorized, When a unit has been
rendered safe by EOD personnel, it shall then
be disposed of in accordance with TM 9-1300206, DARCOM Reg 385-100, or applicable
Work
Requirement
Depot
Maintenance
(DMWR).
1-5. Reference Publications
Refer to Appendix A for reference publications.
TM 43-0001-39
CHAPTER 2
CARTRIDGES
AIRCRAFT FIRE EXTINGUISHER
2-1. General
a. This chapter contains descriptive and
technical data pertaining to the aircraft fire
extinguisher cartridges used in Army aircraft/helicopter fire extinguishing systems.
b. The cartridges described in this chapter are electrically initiated, These cartridges
shall not be resistance-checked either prior to
or after installation in the device of intended
application. Prior to installation of these cartridges, all circuits of the actuating system
shall be open.
2-1 (2-2 blank)
TM 43-0001-39
CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER (M182)
Type Classification:
in diameter, and with an integrally-formed convex head.
Refer to associated aircraft subsystem.

Use:
To release fire extinguishing fluid into the
area surrounding an aircraft engine in the
event of a fire.
Description:
The cartridge consists of a machined brass
casing with a hexagonal midsection and a
threaded end enclosing a pair of electricallyfired DuPont E-92 type squibs, placed side by
side.
The output end of the cartridge is
crimped over a brass slug,
Each squib is a self-contained unit contained in a thin shell of bronze alloy, 0.272-inch
In the assembly one lead wire of each

squib is brought through a phenolic insulator
and soldered to a common center contact, The
insulator is sealed in place by crimping the casing over its edge, The other wire of each squib
is brought into electrical contact with the cartridge casing. Joined in parallel to common electrical contacts, both squibs fire simultaneously.
Each squib creates sufficient force to rupture the frangible disc in the valve body of the
container.
The cartridge is seated in the firing head
of the valve body fixed to the underside of the
extinguishing fluid container, This equipment
is secured within an access pocket in the wing
adjacent to the engine area it is to protect.
2-3
TM 43-0001-39
Functioning
An insulated plug, attached to the firing
head of the container, connects with the aircraft electric supply and to a firing switch in
When the firing
the pilots compartment.
switch is actuated, electric current causes the
squibs to fire, creating gas pressure which propels the slug toward the seal disc, The slug
pierces the segmented frangible seal disc in the
exit valve body. The fluid (CF2B r2 or CF3Br),
which has been held under gas pressure (nitrogen) in the container, is thereby released, and
flows from the fluid container in the wing
access pocket to the distributing nozzles in the
engine area.
Gas, developed by the extinguishing
agent, reduces the oxygen content in the engine
area to a point where combustion cannot be supported, thus quenching the fire.
Recommended firing current is 8 amperes.
Tabulated Data
NSN ----------------------------- 1377-00-756-1384
DODIC --------------------------- M182
Drawing number -------------- 2518519
Vendor CAGE Code and
part number ----------------- (33525) 895188
replaces 841155
Item weight --------------------- 0.17 lb (0,08 kg)
Diameter ------------------------ 1 in. (2.54 cm)
Length --------------------------- 1.38 in. (3.5 cm)
Method of actuation --------- Electrical
Body material ------------------ Brass
Propellant/explosive material:
Type ---------------------------- Lead azide, Type II
Weight ------------------------- 0.00029 lb (2.03
grains)
Performance:
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
2-4
Type ---------------------------- Hermetically-sealed metal container

Dimensions ------------------- 3 in. dia x 2
Items per package ---------- 2 (es)
Weight ------------------------- 1.25 lb
Outer Container:
Reference --------------------- SPI (AM) P-1377M182
Type ---------------------------- PPP-B-1672-Type
II, Style D
Dimensions ------------------- 18 in. x 12 in. x
4.5 in.
Weight ------------------------- 2.5 lb
Cube ---------------------------- 0.56 cu ft
Temperature Limits:
Upper ----------------------------- +160F (71C)
Lower ----------------------------- -65F (-54C)
Shipping and Storage Data:
Quantity distance class ----Storage compatibility
group --------------------------DOT shipping class ----------DOT designation --------------
References:
TM 9-1377-200-20&P
TM 55-1520-209-23
TM 55-1520-227-23
TM 55-1520-240-23
TM 55-1015-204-23
TM 55-1510-213-23
TB 9-1300-385, App B
1.4
s
c
ACTUATING CARTRIDGES, EXPLOSIVE, FIRE
EXTINGUISHER,
HANDLE
CAREFULLY
TM 43-0001-39
CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER: (M193)
Refer to aircraft subsystem.
Use:
To release fire extinguishing agent into
the area surrounding an aircraft engine in the
event of a fire.
tridge, provides the means for completing the

electrical circuit through a grounded bridgewire to the aircraft electrical system.
The aircraft fire extinguisher
threaded into the discharge valve
fire extinguishing agent container,
ment is secured within an access
and between the engines.
cartridge is
body of the
This equiparea above
Functioning
NOTE
To be replaced by MH92.
Description:
The aircraft fire extinguisher cartridge
which is electrically initiated, consists of an aluminum hexagonal midsection with a threaded
end, enclosing an electrically fired squib explosive. Two threaded electrical connectors, one of
which is insulated from the body of the car-
When the fire control switch is operated,

electric current causes the squib to fire, creating gas pressure which separates the split
sleeve from the housing. When the split sleeve
separates, pressure from the fire extinguisher
agent then is released and flows from the container to the distributing nozzles in the engine
area.
Gas developed by the extinguishing agent
reduces the oxygen content in the engine area
to a point where combustion cannot be supported, thus quenching the fire.
2-5
TM 43-0001-39
Tabulated Data
NSN ----------------------------- 1377-00-930-9390
DODIC --------------------------- M193
Drawing number -------------- 2519614
Vendor (CAGE code) and
part number ----------------- (05167) 13083-5
Item weight --------------------- 0.06 lb (0.03 kg)
Diameter ------------------------ 0.906 in. (2.54 cm)
Length --------------------------- 2.5 in. (6.4 cm)
Body material ------------------ Aluminum
Type ---------------------------- Lead Azide, Type II
Weight ------------------------- 0.4409 lb. (3086.3
grains)
Weight ------------------------- .75 lb

Outer Container:
Reference --------------------- PPP-B-1672
Type ---------------------------- Wood box
Dimensions ------------------- .66 x .66x 1.00 ft
Weight ------------------------- 2.5 lb
Cube ---------------------------- .440 ft
Temperature Limits:
Upper ----------------------------- +160F(+71C)
Lower ----------------------------- -65F (-54C)
Bridgewire resistance ------- .90 ohm to

1.40 ohm
Minimum pressure:
-65F (-54C) ---------------- 475 psi in 6 ms
+70F (+21C) ------------- 600 psi in 4 ms
+ 160F (+71C) ----------- 670 psi in 4 ms
Quantity distance class ----- 1.4

Storage compatibility
group --------------------------- S
DOT shipping class ----------- C
DOT designation -------------- ACTUATING
CARTRIDGES,
EXPLOSIVE,
FIRE
EXTINGUISHER,
HANDLE
CAREFULLY
Packaging
References:
Performance:
Inner Container:
Reference --------------------- PPP-C-96
Type ---------------------------- Hermetically sealed metal container
Dimensions ------------------- 2-1/2 in. x 7/8 in.
dia
Items per package ---------- 4
2-6
TM 9-1377 -200 -20&P

TM 55-1520-204-23
TM 55-1520-213-23
TM 55-1520-209-23
TM 55-1510-227-23
TM 55-1510-240-23
TB 9-1300-385, Appendix B
TM 43-0001-39
CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER: (M232)
Type Classification
tact with the cartridge case, Both squibs fire

simultaneously.

Functioning
Use:
event of a fire.
Description:
The cartridge consists of a hexheaded aluminum casing, and a threaded end, enclosing a
pair of electrically-fired Dupont E-92 type
squibs, placed side by side. The output end of
the cartridge is crimped over a brass slug. One
lead wire of each squib is brought through a phenolic insulator and soldered to a common center contact. The insulator is sealed in place by
crimping the casing over its edge. The other
wire of each squib is brought into electrical con-

When the firing
squibs to fire, creating gas pressure which propels the slug toward the seal disc, The slug
exit valve body. The fluid (CF2Brs or CF3Br),
which has been held under gas pressure (nitrogen) is released. The fluid flows from the
container in the wing access pocket to the distributing nozzles in the engine area.
2-7
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DODIC --------------------------Drawing number --------------
1377-01-257-1359
1377-00-087-7103
1377-00-824-5858
M232
2519707/
1660AS200

part number ----------------- 873364
Item weight --------------------- 0.034 lb
(0.0154 kg)
Diameter ------------------------ 1 in. (2.54 cm)
Length --------------------------- 2.560 in. (6.50 cm)
Method of actuation --------- Electrically fired 8
amperes
Type ---------------------------- Lead Azide
Weight ------------------------- 0.00037 lb (2.6
grains)
Firing Temperature Limits:

Upper -------------------------- +160F (+71C)
Lower -------------------------- -65F (-54C)
Packaging
Inner Container:
Reference --------------------- MIL-C-10464
Dimensions ------------------Items per package ---------- 2
Outer Container:
Reference --------------------- PPP-B-621 Class 2
Style 4
Type ---------------------------- Wood box
Dimensions ------------------- 4.75 x 3.5x 3.5 in.
(12.07 X 8.89X 8.89
cm)
Weight ------------------------- 0.3 lb (0.136 kg)
Cube ---------------------------- 0.0337 cu ft
NOTE
M232 P/N 1660AS200 is a replacement
for M232 P/N 2519707, NSN 1377-00824-5858/1377-00-087-7103, The external physical characteristics are identical
except for the identification markings.
Continued use of M232 P/N 2519707 is
authorized until stocks are exhausted.

group --------------------------- S
DOT designation- ------------ ACTUATING
CARTRIDGES,
EXPLOSIVE FIRE
EXTINGUISHER,
HANDLE
CAREFULLY
Performance:
References:
Bridgewire resistance is 0.025 ohms minimum

and 0.100 maximum, The cartridge shall provide sufficient energy to extrude the lead
crusher to a minimum length of 0.224 inches.
TM 9-1377-200-20&P
TM 55-1520-227-23
TM 55-1520-240-23
2-8
TM 43-0001-39
CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER CCU-90/A (MH92)
Refer to aircraft subsystem
Use:
To release fire extinguishing agent into
the engine compartment on the UH-60 helicopter in the event of a fire.
Description:
The aircraft fire extinguisher cartridge is
electrically initiated. It consists of an aluminum hexagonal mid-section with a threaded
end enclosing an electrically fired squib.There
are two threaded electrical connectors, one is

insulated from the body of the cartridge and provides a path for completing the electrical circuit. The other connection is connected to
ground.
Functioning
The aircraft fire extinguisher cartridge is
threaded into the discharge valve body of the
fire extinguishing agent container. Switches for
completing the electrical circuit are located in
the aircraft cockpit. Placing the switch in the
fire position completes the electrical circuit,
thus firing the squib and releasing the fire extinguishing agent.
2-9
TM 43-0001-39
Tabulated Data
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1377-01-185-2622
DODIC --------------------------- MH92
Drawing number -------------- 1512AS105
part number ----------------- (30003) 39040020
Item weight --------------------- 0.066 lb (0.03 kg)
Diameter ------------------------ 0.875 in, (2.22, cm)
Length --------------------------- 2.500 in. (6.35 cm)
Method of actuation --------- Electrically fired
Type ---------------------------- RDX
Weight ------------------------- 0.000441 lb (3,0865
grains)
Performance:
and 1.40 ohms maximum. Pressure ranges
from 475 psi at -65F to 670 psi at + 160F.
Ignition delay shall not exceed 25 milliseconds.
Upper -------------------------- +160F (+71C)
Lower -------------------------- -65F (-54C)
Packaging
Inner Container:
Reference --------------------- MIL-C-10464
2-10

Dimensions ------------------- 6 x 2-5/8 dia
Weight ------------------------- .50
Outer Container:
Reference --------------------- PPP-B-636
Type ---------------------------- Fiberboard box
Dimensions ------------------- 1.54 X 1.04X .27 ft
Weight ------------------------- 2.5 lb
Cube ---------------------------- .560 ft
group --------------------------- s
DOT designation -------------- Actuating Cartridge, Explosive
Fire Extinguisher,
Handle Carefully
References:
TM 9-1377-200-20&P
TM 55-1520-209-23
TM 55-1520-227-23
TM 55-1520-240-23
TM 55-1015-204-23
TM 55-1510-213-23
TM 43-0001-39
CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER (MT20)
tact with the cartridge case. Both squibs fire

simultaneously.

Functioning
Use:
event of a fire in the UH-60 helicopter.
Description:
The cartridge consists of a hexheaded aluminum casing, and a threaded end, enclosing a
pair of electrically-fired Dupont E-92 type
squibs, placed side by side, The output end of
the cartridge is crimped over a brass slug. One
lead wire of each squib is brought through a phenolic insulator and soldered to a common center contact. The insulator is sealed in place by
crimping the casing over its edge, The other
wire of each squib is brought into electrical con-

When the firing
squibs to fire, creating gas pressure which propels the slug toward the seal disc. The slug
exit valve body. The fluid (CF2Brs or CF3Br),
which has been held under gas pressure (nitrogen) is released.
The fluid flows from the
container in the wing access pocket to the distributing nozzles in the engine area.
2-11
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DODIC --------------------------Drawing number -------------Vendor (CAGE code) and
part number ----------------Item weight ---------------------
1377-01-263-3627
MT20
1512AS105
897899
0.034 lb
(0.0154 kg)
Diameter ------------------------ 1 in. (2.54 cm)
Length --------------------------- 2.560 in. (6.50 cm)
Method of actuation --------- Electrically fired 8
amperes
Type ---------------------------- Lead Azide
Weight ------------------------- 0.00037 lb (2.6
grains)
Performance:

Outer Container:
Reference --------------------- PPP-B-621 Class 2
Style 4
Type ---------------------------- Wood box
Dimensions ------------------- 4.75 x 3.5 x 3.5 in
(12.07 X 8.89X
8.89 cm)
Weight ------------------------- 0.3 lb (0.136 kg)
Cube ---------------------------- 0.0337 cu ft

and 0.100 ohms maximum. The cartridge shall
provide sufficient energy to extrude the lead
crusher to a minimum length of 0.224 inches.
Upper -------------------------- + 160F (+71C)
Lower -------------------------- -65F (-54C)
Packaging
Inner Container:
Reference --------------------- MIL-C-10464
2-12
References:
TM 9-1377-200-20&P
TM 55-1520-227-23
TM 55-1520-240-23
1.4
S
C
ACTUATING
CARTRIDGE,
EXPLOSIVE FIRE
EXTINGUISHER,
HANDLE
CAREFULLY
TM 43-0001-39
CHAPTER 3
CUTTERS
3-1. General
A cutter is a cartridge or propellant actuated device that is used in aerial delivery systems for cargo, helicopter cargo and rescue
hoist cable systems and drone recovery systems. Cutters are classified in accordance with
the following characteristics: (1) Method of
Actuation - mechanical or electrical, (2)
Function Time - nondelay or delay.
3-2. Operation
a. Actuation of the mechanical cutter is
accomplished by applying a pull force to the
cable or lanyard with sear attached, The lanyard sear is engaged in the firing pin; therefore,
the pull of the lanyard applies a load to the firing pin spring. Compression of the firing pin
spring and the release of the firing pin are

accomplished with one motion when the firing
pin moves rearward. The sear moves outward
to the cutter body section having an enlarged
internal diameter, which then permits the sear
to move sideward to release the firing pin. The
firing pin is propelled forward under the action
of the spring force and strikes the primer,
which ignites the delay element, if applicable,
then the propellant. Under the force of the propellant gas pressure, the cutter blade is
propelled onto the anvil severing the wires or
cable.
b. Function of electrically or mechanically initiated cutters is basically the same.
The cutters have a specific nondelay or delay
time and shall be used only for their designed
application.
3-1 (3-2 blank)
TM 43-0001-39
CUTTER, CARTRIDGE ACTUATED: M21 (M500)
ATC-S LCC-A
To sever a nylon reefing line which allows

the parachute to fully deploy The cutter is
installed in a mounting bracket which is
attached to the parachute.
Description:
The M21 reefing line cutter is a cartridge
actuated, one shot, disposable mechanical unit
with the cartridge sealed internally, Major components consist of case, firing pin assembly, lanyard, knife assembly delay assembly and cotter
pin.
Functioning:
A drogue chute is used to pull the load out of
the delivery aircraft and to deploy the main
chute, which inflates in a reefed configuration
The deployment of the main chute applies a tensile force to the lanyard assembly, which is
attached to the firing pin. Compression of the
firing pin spring and release of the firing pin
are accomplished with the same motion. The
potential energy stored in the spring propels
the firing pin forward, striking the primer. The
flash of the primer ignites the 2-second pyrotechnic delay mix which, in turn, sets off the propellant charge behind the cutter blade assembly.
Under the force of the propellant gas pressure, the cutter blade separates from the knifedelay assembly and is propelled forward in the
bore of the housing The impact of the blade on
the anvil severs the nylon reefing line inserted
in the cutter, allowing full deployment of the
main parachute.
Change 1 3-3
TM 43-0001-39

Weight -------------------------- 40 lb
NSN ------------------------------DODIC --------------------------Drawing number -------------Vendor (CAGE code) and
part number -----------------Item weight --------------------Diameter ------------------------Length ---------------------------Method of actuation ----------
1377-00-060-0885
M500
8875978
(19200) 8875978
0.75 in. (1.905 cm)

6.0 in. (15.24 cm)
Manual percussion
primer
Body material ------------------ Aluminum alloy/
carbon steel blade
Propellant/Explosive
Material:
Type ---------------------------- Bullseye black powder
Weight -------------------------- 0.0040 lb (28
grains)
Printer -------------------------- Percussion Primer,
M42
Delay Time:
-65F . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 sec
+70F --------------------------- 1.6 sec
2.4 sec
+160F ------------------------- 1.2 sec
maximum
minimum
maximum
minimum
Inner Container:
Reference ---------------------- MIL-P25732/8863435
Dimensions ------------------- PPP.B-636
3-4 Change 1
Outer Container:
Reference ---------------------- 8863436
Type ---------------------------- Wirebound wood
box Type II Class 2
MIL-B-2472
Dimensions ------------------- 12-11/16 x 11-3/8 x
7 in.
Weight -------------------------- 50 lb
Cube ---------------------------- 0.6 cu ft
Temperature Limits:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
Quantity distance class -----Storage compatibility
1.4
S
C
EXPLOSIVE
CABLE CUTTER,
HANDLE
CAREFULLY
KEEP FIRE AWAY
UN Code ------------------------- 0070
UN Proper shipping name - Cutter, Cable,
Explosive
References:
TM 9-1377-200-20&P
TM 10-1670-215-23
TB 9-1300-385, App B
TM 43-0001-39
CUTTER, CARTERIDGE ACTURATED: M22 (M504)
ATC-S LCC-A

the parachute to fully deploy, The cutter is
The M22 reefing line cutter is a cartridge

actuated, one shot, disposable mechanical unit
with the cartridge sealed internally Major components consist of case, firing pin assembly, lanyard, knife assembly delay assembly, and cotter
pin.
Functioning:
A drogue chute is used to pull the load out of
the delivery aircraft and to deploy the main
chute, which inflates in a reefed configuration.
The deployment of the main chute applies a tensile force to the lanyard assembly, which is
flash of the primer ignites the 10-second pyrotechnic delay mix which, in turn, sets off the propellant charge behind the cutter blade assembly.
bore of the housing. The impact of the blade on
main parachute.
Change 1 3-4.1
TM 43-0001-39
Tabulated Data:
NSN ------------------------------DODIC --------------------------Drawing number -------------Vendor (CAGE code) and
part number-----------------Item weight --------------------Diameter ------------------------Width ----------------------------Height ---------------------------Length ---------------------------Method of actuation ----------
1377-00-060-0886
M504
8875979
(19203)
0.75 in. (1.905 cm)

1.07 in.
8.85 in.
5.1 in,
Manual percussion
primer
Body material ------------------ Aluminum alloy/
carbon steel blade
Material:
hype ---------------------------- Bullseye black powder
Weight -------------------------- 0.00043 lb
(3 grains)
Net explosive wt
(incl. delay elements) --- 0.0064 lb
Primer -------------------------- Percussion Primer,
M42
Performance:
Delay Time:
-65F ---------------------------- 15 sec maximum
+70F --------------------------- 10 sec nom,
+160F ------------------------- 8 sec minimum
Packaging:
Inner Container:
Reference ---------------------- 754020103653
3-4.2
Change 1
Type ---------------------------Dimensions ------------------Items per package ---------Weight --------------------------
Fiberboard box
6 x 4.75 in.
1
3 lb
Outer Container:
Reference ---------------------- 8863436
Type ---------------------------- Wirebound wood
box Type II Class 2
MIL-B-2427
Dimensions ------------------- 12-11/16 X 11-3/8 x
7 in.
Weight ------------------------- 50 lb
Cube ---------------------------- 0.6 cu ft
Temperature Limits:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
Quantity distance class -----Storage compatibility
1.4
S
C
EXPLOSIVE
CABLE CUTTER,
HANDLE
CAREFULLY.
KEEP FIRE AWAY
UN Code ------------------------- 0070
UN Proper shipping name - Cutter, Cable,
Explosive
References:
TM 9-1377-200-20&P
TM 10-500/TO 13C7-1-5
TB 9-1300-206/TO11A-1-37
*U.S. G.P.O.:1994-546-043:80739
TM 43-0001-39
CUTTER, CARTRIDGE ACTUATED: (M554)
Description:

Use:
To sever stainless steel cable that has a
breaking strength of 25,000 lbs minimum.
The cable cutter consists of an aluminum

body two steel knives, two Holex 8830-2 cartridges, a protective sleeve, a cartridge O-ring,
and a knife O-ring with a backup ring.
3-5
TM 43-0001-39
Functioning
Firing of the electrically initiated cartridges produces gas pressure within the cutter
body which drives two knives onto the cable, cutting the cable.
Tabulated Data:
NSN ----------------------------- 1377-00-412-4377
DODIC --------------------------- M554
Drawing number -------------- 14195-1
part number ----------------- (96603) 14195-1
Item weight --------------------- 1.26 lb (0.6 kg)
Diameter ------------------------ 2.0 in, (5.08 cm)
Length --------------------------- 7.0 in, (17.78 cm)
Type ---------------------------- HI TEMP
Weight ------------------------- 0.00195 lb (13.658
grains)
Performance:
No-Fire --------------------------- 1.0 amp max for 5
minutes
Bridgewire resistance ------- 1.05 + 0.05 ohms
Insulation resistance -------- 2 megohms min at
500 Vdc
Firing current ------------------ 4.5 amps min
Upper ----------------------------- +125F (+52C)
Lower ----------------------------- -65F (-54C)
3-6
Packaging
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag
Dimensions ------------------- 4 x 12
Weight ------------------------- 1.25 lb
Outer Container:
Reference --------------------- PPP-B-1672
Dimensions ------------------- .70 x .70 x 1.04 ft
Weight ------------------------- 2.5 lb
Cube ---------------------------- .509 cu ft
Shipping and Storage Data
References:
TM 9-1377-200-20&P
TM 55-1520-217-XX-1-23
TM 55-1520-217-XX-2-23
TB 9-1300-385, App B.
1.4
S
C
EXPLOSIVE
CABLE CUTTER,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
CUTTER, CARTRIDGE ACTUATED: P/N 303104-1 (MU02)
Standard.
Use:
UH-1 HELICOPTER or as otherwise
applied.
Description:
The cutter contains an electrically fired
cartridge, shear screw, cutter, body, and anvil.
Functioning:
Firing of the electrically initiated pressure
cartridge produces sufficient gas pressure to
overcome the shear screw. The cutter blade is
driven onto the anvil cutting the cable that
passes through the cutter body.
3-7
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1377-01-087-5166
DODIC --------------------------- MU02
Drawing number -------------Vendor (CAGE code) and
part number ----------------- (22567) 303104-1
(82402) 42277E182
Item weight --------------------- 0.25 lb (0.1134 kg)
Diameter ------------------------ 0.625 in. (1.59 cm)
Length --------------------------- 2.99 in. (7.59 cm)
Bode material ------------------ Steel
Type ---------------------------- Bullseye black
powder
Weight ------------------------- 0.000243 lb (1.7
grains)
Performance:
Bridgewire resistance ------- .9 to 1.1 ohm
Upper ----------------------------- +165F (+74C)
Lower ----------------------------- -65F (-54C)
Dimensions ------------------- 2.25 x 2.25 x 4.50

in.
Weight ------------------------- .25 lb
Outer Container:
Reference ------------------------ PPP-B-1672
Type ----------------------------- II
Dimensions --------------------- 1.54 x 1.04x .35 ft
Weight ---------------------------- 2.50 lb
Cube ----------------------------- .560 cu ft
group --------------------------- S
DOT designation -------------- EXPLOSIVE
CABLE CUTTER,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
Packaging:
References:
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Type I hermetically
sealed metal container
TM
TM
TM
TB
3-8
9-1377-200-20&P
55-1520-210-23 (Series)
55-1520-237-23
9-1300-385, App B
TM 43-0001-39
CUTTER, ASSEMBLY P/N FTL 3648-2 (MU03)
Use:
Designed for interim high altitude parachute delivery systems.
Description:
The cutter contains a thermal battery electrically initiated cartridge, a mechanical firing
pin, steel cutter, and aluminum body.
Functioning:
When the ASPSU is dropped from the aircraft, a mechanical firing pin mechanism is actu-
ated by a pull from a static line attached to the

aircraft. This action cocks and releases a firing
pin, which impacts the percussion primer of the
thermal battery. The thermal battery fires and
produces 19 volts within 0.500 second and maintains a voltage between 19 and 35 volts for a
minimum of 120 seconds, with a 28-milliampere current drain. This energy is stored in
capacitors within the cutter and altitude sensor
modules until the preselected altitude is
reached. At that time the firing circuit is triggered, and an electric current pulse of at least
7.65 amperes is applied to the cartridgeactuated cutter. The cutter then fires, severing
the 9,000-pound (40.03kN)-test woven nylon
line. The G-12 main parachute is then allowed
to open.
3-9
TM 43-0001-39
Tabulated Data
NSN ----------------------------- 1377-01-064-4927
DODIC --------------------------- MU03
Drawing number -------------- 11-1-3043
part number ----------------- (26687) FTL
3648-2
Item weight --------------------- 1.81 lb (0.82 kg)
Diameter -----------------------Length --------------------------Method of actuation --------- Electric
Body material ------------------ Steel
Type ---------------------------- HI TEMP
Weight ------------------------- 0.0004 lb (2.8
grains)
Weight ------------------------- 4.688 lb

Outer Container:
Reference --------------------- PPP-B-621
Type ---------------------------- Wood Box
Dimensions ------------------Weight ------------------------Cube ---------------------------Shipping and Storage Data:
Packaging:
Inner Container:
Reference --------------------- MIL-B-81705
Type ---------------------------- Hermetically sealed antistatic plastic
bag
Dimensions ------------------- 11 x 3.5 x 3.5 in.
(27.9 x 8.9 x
8.9 cm)
3-10
1.4
S
C
EXPLOSIVE
CABLE CUTTER,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
Temperature Limits:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
References:
TM 9-1377-200-20&P
TB 9-1300-385, App B
TM 43-0001-39
CUTTER, DELAY, PROPELLANT ACTUATED: (MU11)

flash of the primer ignites the four-second pyrotechnic delay mix which, in turn, sets off the propellant charge behind the cutter blade assembly.
Use:
the parachute to fully deploy The cutter is
Description:
The MU11 reefing line cutter is a cartridge actuated, one shot, disposable mechanical unit with the cartridge sealed internally.
Major components consist of case, firing pin
assembly, lanyard, knife assembly, delay assembly and cotter pin.
Functioning:
A drogue chute is used to pull the load out
of the delivery aircraft and to deploy the main
chute, which inflates in a reefed configuration.
The deployment of the main chute applies a tensile force to the lanyard assembly which is
bore of the housing. The impact of the blade on
main parachute.
Tabulated Data:
NSN ----------------------------DODIC --------------------------Drawing number -------------Vendor (CAGE code) and
part number ----------------Item weight --------------------Diameter -----------------------Length --------------------------Method of actuation ---------
1377-01-288-0418
MU11
6261278
11862
.7 lb
0.75 in. (1.905 cm)
6.0 in. (15.24 cm)
Manual percussion
primer
alloy/carbon steel
blade
3-11
TM 43-0001-39
Type ---------------------------- Bullseye black
powder
Weight ------------------------- 0.0040 lb (28
grains)
Performance:
Delay Times:
-65F --------------------------- 3.0 sec mm
+70F ------------------------- 1.6 sec min 2.4 sec
max
+ 160F ------------------------ 1.2 sec min
Packaging:
Inner Container:
Reference --------------------- PPP-B-636
Weight ------------------------- 43 lb
Outer Container:
Reference --------------------- MIL-B-2427
Type ---------------------------- Wood box
3-12
Dimensions ------------------- 15-13/16 x 12-15/16

in.
Weight ------------------------- 50 lb
Cube ---------------------------Temperature Limits:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
References:
TM 9-1377-200-20&P
TM 10-1670-215-23
TB 9-1300-385, App B
1.4
S
C
EXPLOSIVE
CABLE CUTTER,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
CHAPTER 4
TIME DELAY CARTRIDGES
4-1. General
a. Delay cartridges consist of a body a
primer seat, a primer, a time delay charge, an
output charge, and a closure disc. The composition and the measure of the delay element
(charge) determine the length of the delay.
b. Time delay cartridges are designed to

function at specific delay times and shall only
be used for designed application.
c. This chapter contains technical data
for the time delay cartridges used by the Army.
4-1 (4-2 blank)
TM 43-0001-39
CARTRIDGE, DELAY CCU-57/B (MF35)
ATC-S LCC-A
Use:
The CCU-57/B (MF35) delay cartridge is
sealed in the TCU-1B thruster. The TCU-1B
thruster is part of a high speed aerial delivery
system.
Description:
Major components consist of aluminum
case, primer, O-ring, delay charge and main output charge.
Functioning:
Firing of the M42 primer ignites the 0.4
second delay train which in turn fires the main
output charge that provides gas pressure for
the thruster.
Tabulated Data:
NSN ----------------------------- 1377-01-084-6046
DODIC --------------------------- MF35
Drawing number -------------- 5184858

part number ----------------- (53711) 5184858
Item weight --------------------Diameter ----------------------- 0.375 in. (0.9525
cm)
Length --------------------------- 2 in. (5.08 cm)
Method of actuation --------- Percussion primer
M43
Body material ------------------ Aluminum alloy
Type ---------------------------- Black powder and
HES 5808
Weight ------------------------- 0.0025 lb (17.5
grains)
Performance:
Delay time ---------------------- 0.4 + 0.1 second
Thrust (upper limit) --------- 2000 lb (900 kg)
max
Minimum stroke -------------- 1.5 in. (3.8 cm)
4-3
TM 43-0001-39

Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
This item cannot be procured or packaged
separately. It is installed in the TCU-1B thruster as a sealed-in-device.

DOT designation -------------- SMALL ARMS
AMMUNITION,
CLASS C,
HANDLE
CAREFULLY
KEEP FIRE AWAY
References:

group --------------------------- S
4-4
TM 9-1377-200-20&P
TM 9-1300-385, App B.
TM 43-0001-39
CARTRIDGE, DELAY CCU-89/B: (MH88)
Use:
The MH88 activates the release mechanism used in the parachute harness of cargo
dropped from aircraft. The release mechanism
allows the parachute to detach from the cargo
This prevents the parachute
after landing.
from dragging the cargo and causing damage.
Description:
The cartridge consists of a cylindrical aluminum body primer (ignition device), washer,
ignition charge, delay charge, filler charge, output charge, and metal closure charge.
Functioning:
Primer initiation ignites a composition
igniter charge adjacent to the delay column.
Upon the elapse of approximately 20 seconds
the delay mix ignites the filler and output
charge.
4-5
TM 43-0001-39
CARTRIDGE, DELAY CCU-89/B: MH88

Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . 1377-01-178-6691
DODIC --------------------------- MH88
Drawing number -------------- 5185107
part number ----------------- (30003) 5185107
Item weight --------------------Diameter ------------------------ 0.506 in. (1.29 cm)
Length --------------------------- 2.0 in. (5.08 cm)
Method of actuation --------- Percussion (M42)
Type ----------------------------- Tungsten delay
composition
Weight ------------------------- 0.00616 (42 grains)
Performance:
20 second delay.
Outer Container:
Reference --------------------Type ---------------------------- Wood box
Dimensions ------------------- 8.38 x 8.38 x 14.63
in.
Weight ------------------------Cube ---------------------------- 0.6 cu ft
Temperature Limits:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------Type ---------------------------Dimensions ------------------Items per package ---------- 10
Weight -------------------------
4-6
References:
TM 9-1377-200-20&P
TM 10-1670-215-23
TB 9-1300-385, App B.
1.4
S
C
SMALL ARMS
AMMUNITION,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
CARTRIDGE, DELAY: (M308)
ATC-S LCC-A
Use:
Power device for the 5,000 lb. capacity
cargo parachute release.
NOTE
Replacement is MH88.
Description:
The M252 delay cartridge is cylindrical in
shape, It consists of the body a primer seat,
washer, M42 primer, A1A igniter charge, delay
charge, output charge, and closing disc.
Functioning:
Its function is to allow a nominal 20second delay, during which cargo descent is stabilized, before tripping a spinner mechanism
which allows the parachute to release upon landing.
4-7
TM 43-0001-39
When the cargo is jettisoned from the aircraft, parachute deployment activates the firing
mechanism. This compresses a spring behind
the firing pin. The stored energy of the compressed spring drives the firing pin into the
M42 percussion primer of the M252 cartridge.
Primer initiation ignites an A1A composition igniter charge adjacent to the delay
column. Upon the elapse of approximately 20
seconds, the delay mix ignites the filler and output charge; the resulting gases rotate the spinner on the release mechanism which releases
the ground disconnect pin attached to the
catch. Upon ground contact (no load on the
release), the rotated spinner allows the latch
holding the cargo to release. Thus, the parachute is prevented from dragging or causing
the cargo to tumble along the ground.
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DODIC --------------------------Drawing number -------------Vendor (CAGE code) and
part number -----------------
1377-00-958-1048
M308
8886478 (19203)
(81337) 11-1-329
(26687)
Item weight --------------------- 0.007 lb (0.0032
kg)
Diameter ------------------------ 0.375 in. (0.9525
cm)
Length --------------------------- 2 in. (5.08 cm)
M42
Type ---------------------------- Lead azide
Weight ------------------------- 0.006 lb (42 grains)
Packaging:
Inner Container: 1
Reference --------------------- PPP-B-636
Weight ------------------------- 0.70 lb (0.32 kg)
Inner Container: 11
Reference --------------------- MIL-B-117
Type ---------------------------- Barrier bag
Weight ------------------------- 1.5 lb (0.68 kg)
Outer container:
Reference --------------------- PPP-631
Type ---------------------------- Class 2/Style 4
Dimensions ------------------- Wood box
Weight ------------------------- 30 lb (13.6 kg)
Cube ----------------------------
Skipping and Storage Data:

group --------------------------- S
AMMUNITION,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
Performance:
Delay time ---------------------- 20 seconds
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
4-8
References:
TM 9-1377-200-20&P
TM 10-1670-215-23
TB 9-1300-385, App B.
TM 43-0001-39
CHAPTER 5
EMERGENCY ESCAPE SYSTEMS FOR
HELICOPTERS, AH-64
Section I. AH-1 (COBRA)
5-1. General (for Army AH-1 (Cobra)
Helicopter)
a. Section I of this chapter contains descriptive and technical data pertaining to systems used for the Army AH1E-F/P/S (MOD)
Emergency Escape
Helicopter Personnel
Systems. Each system is used to explosively cut
the windows of the canopy and doors from the
canopy support structure to provide a rapid
means of escape/access to/from the crew compartment.
b. The system consists of four linear
explosive window cutting assemblies (WCA)
which are installed around the rim of the canopy and door windows of the crew compartment
(fig. 5-1), three armed/firing mechanisms, and
interconnecting flexible confined detonating
cords (FCED) and rigid shielded mild detonating cord (SMDC) lines (fig. 5-2). One armed/fir-
ing mechanism is located in the pilots

instrument panel to the left of the glare shield,
another is located in the gunner/copilots right
console, and the third is in the nose of the helicopter located to provide external access by rescue personnel, Any one of the three armed/firing mechanisms can be used to actuate the
linear explosive escape system.
c. The detonating cord set consists of
eight SMDC assemblies, two FCDC assemblies
and four WCA assemblies. Each type assembly
is described in this section. Individual detonating cord lines are listed in table 5-1. Table 5-2
lists these components and their location and
function. Table 5-3 lists detonating cord assemblies used in AH-1 series Army helicopters.
d. Section I also contains descriptive information pertaining to the inert connectors used
in the helicopter canopy removal system.
5-1
TM 43-0001-39
Figure 5-1. Attack Helicopter, Model AH-1, All Modifications,

Emergency Canopy Jettison Elements.
5-2
TM 43-0001-39
Table 5-1. Explosive Components Technical Data and Cross-Reference

AH-1 Series
DODIC
Assembly
*T-McC-S
P/N
**Bell P/N
NSN
1377-oo-
Length (IN.)
Explosive
Weight (LB)
MD15
FCDC
813592-6
209-030-711-11
410-8271
67,5
0,01115
MD16
FCDC
813592-5
209-030-711-13
409-1099
22.4
0,00787
MD17
SMDC
813475-19
209-030-711-19
410-8297
6.5
0.00065
MD18
SMDC
813475-27
209-030-711-27
409-1098
6.6
0.00063
MD33
WCA
814280-15
209-030-711-105
409-1096
150,0
0.00461
MD34
WCA
814280-9 or
814280-13
209-030-711-99
409-1095
110.0
0.00390
MD35
WCA
209-030-711-37
814280-102
or 814280-11
106-7773
110,0
0.00375
MD36
WCA
814280-101
or 814280-9
409-1097
150.0
0.00466
ME83
***CORD
SET, DETONATING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01-0608531
ARMED/
FIRING
MECHANISM
813633-4
209-030-711-103
209-030-711-61
410-8265
. . . . . . . . . . . . . . . . . . 0.03268
6.5
0.00019
*CAGE Code 06331

**CAGE Code 97499
***Contains one each of of all items except the armed/firing mechanism
5-3
TM 43-0001-39
Table 5-2. Summary of Devices in AH-1

Series Canopy Release System
DODIC
Nomenclature
*Function
MD15
Flexible Confined
Detonating Cord
(FCDC) 857AS500-2
1- Between left junction manifold and WCA

gunners door
Provides flexible explosive media between

junction manifold and
MD16
FCDC - 857AS500-1
1- Between right junction manifold and WCA

pilots door
Provides flexible explosive media between

junction manifold and
WCA
MD17
Shielded Mild
Detonating Cord
(SMDC) - 857AS400-1
1- Between left junction manifold and WCA

pilots window
Provides explosive
media between junction
manifold and WCA
MD18
SMDC - 857AS400-2
1- Between right junction manifold and WCA

gunners window
Provides explosive
media between junction
manifold and WCA
MD33
Window Cutting
Assembly (WCA) 857AS300-4 or
857AS300-15
1- Pilots canopy window
Explosively cuts
(removes) and ejects
glass from pilots canopy window
MD34
WCA - 857AS300-3 or
857AS300-13
1- Gunners canopy
window
Explosively cuts
glass from gunners
canopy window
MD35
WCA - 857AS300-2 or
857AS300-11
1- Gunners door window
Explosively cuts
glass from gunners
door window
MD36
WCA - 857AS300-1 or
857AS300-9
1- Pilots door window
Explosively cuts
glass from pilots door
window
ME83
Cord Set, Detonating,

Canopy Removal
System 857AS600
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System procurement
Armed/Firing
Mechanism
3- One each at pilots

and gunners stations
and one in fuselage
nose
*Service life at end of table.
5-4
Quantity/Location
Initiates detonation
wave to actuate window
cutting assemblies
TM 43-0001-39
Table 5-2. Summary of Devices in AH-1 Series

Canopy Release System (Continued)
DODIC
Nomenclature
Quantity/Location
**Function
INERT
In-line connector
857AS103-1
1- Forward bulkhead
section
Detonation transfer
media
INERT
Tee Connector
857AS101-1
1- Behind gunners
seat
Detonation transfer
media
INERT
Cross Connector
857AS102-1
Detonation transfer
2- Upper right canopy
structure and upper left media
canopy structure
*Service Life: (Explosive Devices)
**Service Life: (Inert Connectors)
Service life listed in this TM is nominal.

Specific service life data is listed in TB 9-1300385, App B. Updates to the TB are issued quarterly
Item is an assembly of metal parts only.

Replacement is determined by On Condition
(OC), after inspection for visible wear or defect,
5-5
TM 43-0001-39
Table 5-3. Detonating Cord Assemblies and Elements

Used in Army Helicopters: AH-1 Series
NSN
DODIC
*(CAGE) P/N
Nomenclature
1377-00-409-1100
MS50
Cord, Detonating
(SMDC)
(97499) 209-030-711-25
(06331) 813475-25
1377-00-410-8222
MS49
Cord, Detonating
(SMDC)
(97499) 209-030-711-21
(06331) 813475-21
1377-00-410-8228
....
Manifold, Junction
(Inert)
(97499) 209-030 -711-9

(06331) 813487-2
1377-00-410-8266
MS47
Cord, Detonating
(SMDC)
(97499) 209-030-711-15
(06331) 813475-15
1377-00-410-8289
MS48
Cord, Detonating
(SMDC)
(97499) 209-030-711-17
(06331) 813475-17
1377-01-032-1047
MS76
Cord, Detonating
(LSC)
(97499) 209-033-009-1
(06331) 816986-1
1377-01-032-1048
MS77
Cord, Detonating
(LSC)
(97499) 209-033-009-3
(06331) 816986-3
1377-01-032-1049
MS78
Cord, Detonating
Window Cutting Assy
(97499) 209-033-010-103
(06331) 816987-103
1377-01-032-1050
MS79
Cord, Detonating
Window Cutting Assy
(97499) 209-033-010-105
(06331) 816987-105
1377-01-032-3279
MS60
Cord, Detonating
(SMDC)
(97499) 209-033-011-123
(06331) 813475-123
1377-01-032-3280
MS61
Cord, Detonating
(SMDC)
(97499) 209-033-011-23
(97499) 209-033-011-49
1377-01-100-1718
MS62
Cord, Detonating
(SMDC)
(30003) 813-475-127
1377-01-032-3283
MS59
Cord, Detonating
(SMDC)
(97499) 209-033-011-125
(06331) 813475-125
1377-01-032-3286
MS58
Cord, Detonating
(SMDC)
(97499) 209-033-011-119
(06331) 813475-119
1377-01-033-5088
---
Arm, Fire Initiator
(97499) 209-033-008-101
(06331) 814033-101
1377-01-035-4124
MS51
Cord, Detonating
(SMDC)
(97499) 209-033-011-105
(06331) 813475-105
1377-01-037-4090
MS53
Cord, Detonating
(SMDC)
(97499) 209-033-011-109
(06331) 813475-109
*Coxmnercial And Government Entity (CAGE)

(Formerly FSCM Code).
5-6
TM 43-0001-39
Table 5-3. Detonating Cord Assemblies and Elements

Used in Army Helicopter AH-1 Series (Continued)
NSN
DODIC
*(CAGE) P/N
Nomenclature
1377-01-037-4091
....
Pin Puller, Explosive
(97499) 209-033-006-101
(06331) 816984-107
1377-01-037-4092
....
Manifold, Junction
(Inert)
(97499) 209-033-011-101
(06331) 817295-101
1377-01-037-4093
MS57
Cord, Detonating
(SMDC)
(97499) 209-033-011-117
(06331) 813475-117
1377-01-037-4094
MS56
Cord, Detonating
(SMDC)
(97499) 209-033-011-115
(06331) 813475-115
1377-01-037-4095
MS55
Cord, Detonating
(SMDC)
(97499) 209-033-011-113
(06331) 813475-113
1377-01-037-4096
MS54
Cord, Detonating
(SMDC)
(97499) 209-033-011-111
(06331) 813475-111
1377-01-037-9237
MS52
Cord, Detonating
(SMDC)
(97499) 209-033-011-107
(06331) 813475-107
1377-01-062-4195
....
Connector, In-line
(Inert)
(97499) 209-033-011-103
(06331) 819347-103
*Coxmnercial And Government Entity (CAGE)

(Formerly FSCM Code Number).
5-7
TM 43-0001-39
Figure 5-2. Canopy Jettison Removal System (Schematic) for the AH-1 Series.
5-8
TM 43-0001-39
CORD, DETONATING, ASSEMBLY, FLEXIBLE CONFINED (FCDC) (GUNNER): (MD15)
the canopy between the left junction manifold

and the adapter to the WCA in the gunners canopy door.
Use:
NOTE
To provide and interconnecting explosive
media to the Window Cutting Assembly (WCA)
of the gunners canopy door used in the
Emergency Canopy Removal System of the AH1 series Helicopter.
The MD15 is identical in design and physical appearance to the MD16, The difference is in length and amount of explosive,
Description:
Functioning
Major components of the FCDC assembly

are housing, threaded fittings, seals, loaded
charge case, lead sheath assembly, and prescribed amounts of Hexanitrostilbene (HNS).
This FCDC lead sheathed assembly is located in
When any one of the three armed/firing

mechanisms is actuated, the FCDC line
receives a detonating stimulus via a junction
manifold and transmits it to the WCA in the
gunners canopy door.
5-9
TM 43-0001-39
Tabulated Data:
NSN ----------------------------- 1377-00-410-8271
DODIC --------------------------- MD15
Drawing number -------------- 857AS500-2
part number ----------------- (97499) 209-030711-11 (06331)
813592-6
Item weight --------------------Diameter ------------------------ 0,5 in, (1.27 cm)
Length --------------------------- 67,5 in, (171,45 cm)
Method of actuation --------- High order detonation wave
Body Material ------------------ Lead 6% antimony
alloy sheathed
Types --------------------------- HNS, Type I Grade
A
Weight ------------------------- 0.01115 lb. (78.05
grains)
Performance:
Minimum detonation
velocity ------------------------ 6050 meters/see at
-65 (-54C)
Inner container:
Reference --------------------- MIL-B-817051
857AS500-2
Type ---------------------------- Sealed bag
Dimensions ------------------- 68 long x 1 dia
(172.7 cm long x
2.5 cm dia)
Weight ------------------------- 0.5 lb (0.23 kg)
Outer Container:
Reference --------------------- Commercially
packed
Type ---------------------------- II
Dimensions ------------------- 1.54 x 1.04x .27
Weight ------------------------- 1.50 (lb)
Cube ---------------------------- .464 cu ft

Reference:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
5-10
TM
TM
TM
TM
9-1377-200-20&P
55-1520-221-23
55-1520-234-23
9-1300-385, App B.
1.4
S
C
Flexible Linear
Shaped Charge,
Handle Carefully
Keep Fire Away
TM 43-0001-39
CORD, DETONATING, ASSEMBLY, FLEXIBLE CONFINED (FCDC) (PILOT): (MD16)
tion manifold and the adapter to the WCA in

the pilots canopy door,
Use:
To provide and interconnecting explosive
of the pilots canopy door used in the
Emergency Canopy Removal System of the AH1 series Helicopter,
Description:
Major components of the FCDC Assembly
are housing, threaded fittings, seals charge
case, Hexanitrostilbene (HNS), lead sheathed
assembly This FCDC lead sheathed assembly
is located in the canopy between the left junc-
NOTE
The MD16 is identical in design and physical appearance to the MD 15. The difference is in length and amount of explosive.
Functioning:
When any one of the three armed/firing
mechanisms is actuated, the FCDC line
receives a detonating stimulus via a junction
manifold and transmits it to the WCA in the
pilots canopy door.
5-11
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DODIC --------------------------Drawing number -------------Vendor (CAGE Code) and
part number -----------------
1377-00-409-1099
MD16
857AS500-1
(97499) 209-030711-13 (0633.1)
813592-5
Item Weight -------------------Diameter ------------------------ 0.5 in. (1.27 cm)

Length --------------------------- 22.4 in. (58.9 cm)
alloy sheathed
Type ---------------------------- HNS, Type I, grade
A
Weight ------------------------- 0.00187 lb (55.09
grains)
Performance:
Type ---------------------------- Type I, Hermetically sealed metal

container
Dimensions ------------------- 62-1/2 x 1/2 in.
Weight ------------------------- 0.2 lb (0.09 kg)
Outer Container:
Reference --------------------- Commercially
packed
Type ---------------------------- II
Dimensions ------------------- 1.54 X 1.04X .27 ft
Weight ------------------------- 2 lb
Cube ---------------------------- .464 ft
Minimum detonation
velocity ------------------------ 6050 meter/see at
-65F (-54C)
Upper ----------------------------- +200F (+93 C)
Lower ----------------------------- -65F (-54 C)
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
5-12
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B.
1.4
S
C
FLEXIBLE
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
CORD, DETONATING, ASSEMBLY, SHIELDED MILD (SMDC): (MD17)
shell, and silver sheathed mild detonating cord.

This assembly is located between the left junction manifold and the WCA in the pilots canopy door.
Use:
To provide an interconnecting explosive
of the pilots canopy door used in the
Emergency Canopy Removal System of the AH1 series Helicopter,
Description:
Major components of the FCDC Assembly
are (MD17) are threaded fittings, seals washers, inner and outer ferrules, loaded booster
Functioning:
Upon actuation of the system by arming
and firing any one of the three armed/firing
mechanisms, a detonation wave is received via
the left junction manifold and is boosted by the
loaded booster shell. The stimuli from the
booster actuates the HNS within the SMDC
assembly to the adapter of the pilots canopy
WCA.
5-13
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-00-410-8297
MD17
857AS400-1
(97499) 209-030711-19 (06331)
813475-19
Item Weight -------------------Diameter ------------------------ 0.23 in. (0.58 cm)

Length --------------------------- 6.45 in. (16.4 cm)
Body Material ------------------ Silver sheathed,
high fine silver
99.95%
A
Weight ------------------------- 0.00065 lb (4.55
grains)
Performance:
Type ---------------------------- Type II, heat

sealed, anti-static
plastic bag
Dimensions ------------------- 12 in. long x 1. in.
dia (30.4 cm long x
2,54 cm dia)
Weight ------------------------- 0.2 lb (0.091 kg)
Outer Container:
Reference --------------------- PP-B-621
Type ---------------------------- Class II style 4
Wood BOX
Dimensions ------------------- 1.54 X 1.04X .27 ft
Weight ------------------------- 2 lb
Cube ---------------------------- .464 ft

Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging
Inner Container:
Reference --------------------- MIL-B-81795
5-14
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
CORD, DETONATING, ASSEMBLY, SHIELDED, MILD (SMDC): (MD18)
This assembly is located between the right

junction manifold and the WCA of the gunners
canopy window.
Functioning:
Use:
of the gunners canopy window used in the
Description:
Major components of the SMDC Assembly
(MD18) are threaded fitting seals, washers,
inner and outer ferrules, loaded booster shell,
and silver sheathed mild detonating cord,

the left junction manifold and is boosted by the
assembly to the adapter of the gunners canopy
WCA.
NOTE
The MD18 is identical to the MD17 in
physical appearance and design, The difference is in length and amount of explosive,
5-15
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-00-409-1098
MD18
857AS400-2
(97499) 209-030711-27 (06331)
813475-27
Item Weight -------------------Diameter ------------------------ 0.23 in. (0,58 cm)

Length --------------------------- 6.0 in. (15.24 cm)
high fine silver
99.95%
Type ---------------------------- HNS, Type I Grade
A
Weight ------------------------- 0.00063 lb (4,41
grains)
Performance:
Minimum detonation
-65F (-54C)
Type ---------------------------- Type II, heat sealed

anti-static plastic
bag
Dimensions ------------------- 12 in. long x 1. in.
dia (30.48 cm long x
2.54 cm dia)
Weight ------------------------- 0.2 lb (0.91 kg)
Outer Container:
Reference --------------------- PPP-C-1672
Type ---------------------------- Class II style 4
Wood BOX
Weight ------------------------- 2 lb
Cube ---------------------------- .464 ft


Upper -------------------------- +200F (+93C)
Lower -------------------------- -65 F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-81705
5-16
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
CUTTING ASSEMBLY, WINDOW (WCA): (MD33)
Use:
An explosive device used in the AH-IS
(MOD) Helicopter Emergency Canopy Removal
System to assure exit from or access to the crew
compartment of the aircraft in an emergency.
Description:
Major components of the WCA are: manifold release assemblies and window cutting
retainer subassemblies for doors and windows,
linear explosive,
retainer, and seal,
resilient back-up cushion,
The assemblies are located on the periphery of the four windows in the crew compartment.
Functioning
the interconnecting FCDC and SMDC lines to
the linear explosive of the WCA. The explosive
force is outward, simultaneously cutting out
the four plastic window glasses of the crew compartment,
5-17
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-00-409-1096
MD33
857AS300-4
(97499) 209-030711-35 (06331)

813475-104
Item Weight -------------------- 5 lb (2.27 kg)
Width ----------------------------- 32 in. (81.3 cm)
Height ---------------------------- 5 in. (12.7 cm)
Length --------------------------- 62 in. (157,5 cm)
alloy sheathed Propellant/explosive material:
Type ---------------------------- HNS, type II, grade
B
Weight ------------------------- 0.004608 lb (32.3
grains)
Performance:
Dimensions ------------------- 72x 32x 5 in,

Weight ------------------------- 3 lb
Outer Container:
Reference --------------------Type ---------------------------Dimensions ------------------Weight ------------------------Cube ---------------------------Temperature Limits:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Minimum detonation
-65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-81705
anti-static plastic
bag
5-18
PPP-B-636
Fiber board box
6,63 x 3.29x 1.05 ft
52 lb
23.108 ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
CLASS C EXPLOSIVE, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
An explosive device used in the AH-1 S
compartment of the aircraft in an emergency
Description:
retainer sub-assemblies for doors and window,

linear explosive, resilient back-up cushion,
retainer, and seal.
The assemblies are located on the outer
edge of the four windows in the crew compartment.
Functioning:
the four plastic window glasses of the crew compartment.
5-19
TM 43-0001-39
Tabulated Data:
NSN - - - - - - - - - - - --- - - - - - - - - - DODIC --------------------------Drawing number -------------Vendor (CAGE Code) and
part number -----------------
1377-00-409-1095
MD34
857AS300-3
(97499) 209-030711-29 (06331)

813475-9
Item Weight -------------------- 5 lb (2.27 kg)
Width ----------------------------- 32 in. (81.3 cm)
Height ---------------------------- 5 in. (12.7 cm)
Length --------------------------- 62 in. (157.5 cm)
alloy sheathed
B
Weight ------------------------- 0.003902 lb (27.3
grains)
Performance:
Dimensions ------------------- 40x 70 in.

Weight ------------------------- 5.00 lb
Outer Container:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Minimum detonation
velocity ------------------------ 6050 meter/sec at
-65F (-54C)
Packaging:
References:
Inner Container:
Reference --------------------- MIL-B-81705
anti-static plastic
bag
5-20
PPP-B-636
Fiber board box
5.60 X 3.42x 1.08 ft
47 lb
20.728 ft
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:

retainer, and seal.
Functioning:
5-21
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-00-106-7773
MD35
857AS300-2
(97499) 209-030711-29 (06331)

813475-102
Item Weight -------------------- 5 lb (2.27 kg)
Width ----------------------------- 32 in. (81.3 cm)
Height ---------------------------- 5 in. (12.7 cm)
Length --------------------------- 62 in. (157.5 cm)
alloy sheathed
B
Weight ------------------------- 0.003902 lb (24,7
grains)
Performance:
Dimensions ------------------- 38x 65 in.

Weight ------------------------- 3 lb
Outer Container:
Reference --------------------- PPP-B-636
Type ---------------------------- Fiber board box
Dimensions ------------------- 15-1/2 X 40-1/2X
65-1/2 in.
Weight ------------------------- 46 lb
Cube ---------------------------- 23.949 ft
Temperature Limits:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Minimum detonation
-65F (-54C)
Packaging:
References:
Inner Container:
Reference --------------------- MIL-B-81705
anti-static plastic
bag
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
5-22
1.4
S
C
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:

retainer, and seal.
Functioning:
mechanism, a detonation wave is received via
5-23
TM 43-0001-39
Tabulated Data:
NSN ----------------------------DODIC --------------------------Drawing number -------------Vendor (CAGE Code) and
part number -----------------
1377-00-106-1097
MD36
857AS300-1
(97499) 209-030711-29 (06331)

813475-101
Item Weight -------------------- 5 lb (2.27 kg)
Width ----------------------------- 32 in. (81.3 cm)
Height ---------------------------- 5 in. (12.7 cm)
Length --------------------------- 62 in. (157.5 cm)
alloy sheathed
B
Weight ------------------------- 0.004365 lb (30.6
grains)
Performance:
Dimensions ------------------- 29,5 x 7 x 75.5 in.

Weight ------------------------- 3 lb
Outer Container:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65 F (-54C)
Minimum detonation
-65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-81705
anti-static plastic
bag
5-24
PPP-C-636
Fiber board box
6.54 x 2.83x .98 ft
50 lb
18.138 ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
CORD, DETONATING, ASSEMBLY, SHIELDED, MILD (SMDC): (MS47)
Refer to aircraft subsystem,
Use:
Description:
are threaded fitting, seals, washers, inner and
outer ferrules, loaded booster shell, and silver
sheathed mild detonating cord.
Functioning:
the junction manifold and is boosted by the
assembly,
NOTE
The MS47 thru MS62 are identical in
physical appearance and design, The difference is in length and amount of explosive.
5-25
TM 43-0001-39
Tabulated Data:
part number -----------------
1377-00-410-8266
MS47
857AS400-15
(30003) 813475-15
209-030-711-15
Item Weight -------------------- 0.268 lb
Diameter ------------------------ 0,18 in.
Length --------------------------- 32,0 in.
high fine silver
99.95%
A
Weight ------------------------- 0,001860 lb
Performance:
Type ---------------------------- Bag, sealed

Dimensions ------------------- 6 x 55 in.
Weight ------------------------- 0.50 lb
Outer Container:
group -------------------------DOT shipping class ----------DOT designation --------------
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-26
PPP-B-636
Fiber board box
3.20 x 1.60x 1.08 ft
15 lb
5.530 ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning:
assembly.
NOTE
physical appearance and design. The difference is in length and amount of explosive.
5-27
TM 43-0001-39
Tabulated Data:
Packaging:
NSN ----------------------------- 1377-00-410-8289

DODIC --------------------------- MS48
Vendor (CAGE Code) and
part number ----------------- (30003) 813475-15
209-030-711-17
Item Weight -------------------- 0.227 lb
Diameter ------------------------ .18 in,
Length --------------------------- 30 in.
high fine silver
99.95%
A
Weight ------------------------- 0,001561 lb
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 4 x 40 in.
Weight ------------------------- 0.501 lb
Performance:
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 3.06 x 1.25 x .93 ft
Weight ------------------------- 15 lb
Cube ---------------------------- 3.568 ft
Minimum detonation
-65F (-54C)
References:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
5-28
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
Refer to aircraft subsystem,
Use:
Description:
Functioning
assembly.
NOTE
5-29
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
Packaging:
1377-00-410-8222
MS49
857AS400-21
(30003) 813475-21
209-030-711-21
Item Weight -------------------- 0.389 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 34 in.
high fine silver
99.95%
A
Weight ------------------------- 0.002685 lb
Performance:
Inner Container:
Reference --------------------Type ---------------------------Dimensions ------------------Items per package ---------Weight -------------------------
MIL-B-117
Bag, sealed
6 x 47 in.
1
0.50 lb
Outer Container:
Reference --------------------Type ---------------------------Dimensions ------------------Weight ------------------------Cube ----------------------------
PPP-B-636
Fiber board box
3.62 X 3.29 1.33 ft
20 lb
11.464 cu ft

Minimum detonation
-65F (-54C)
References:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
5-30
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description (General all sizes)
Functioning
assembly.
NOTE
5-31
TM 43-0001-39
Tabulated Data:
part number -----------------
Packaging:
1377-00-409-1100
MS50
857AS400-25
(30003) 813475-25
209-030-711-25
Item Weight -------------------- 0.543 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 52 in.
high fine silver
99.95%
A
Weight ------------------------- 0.003856 lb
Performance:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 100 in.
Weight ------------------------- 0.75 lb
Outer Container:

Minimum detonation
-65F (-54C)
References:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
5-32
PPP-B-636
Fiber board box
3.50 x 4.75 x 1.37 ft
17 lb
22.776 cu ft
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
Use:
of the gunner's canopy window used in the
Description: (General all sizes)
Functioning
assembly.
NOTE
5-33
TM 43-0001-39
Tabulated Data:
part number -----------------
Packaging:
1377-01-035-4124
MS51
857AS400-105
(30003) 813475-105
209-033-011-105
Item Weight -------------------- 0.400 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 40 in.
high fine silver
99.95%
A
Weight ------------------------- 0,002872 lb
Performance:
Inner Container:
Reference --------------------- MIL-B-636
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 79 in.
Weight ------------------------- 2.50 lb
Outer Container:

Minimum detonation
-65F (-54C)
References:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
5-34
PPP-B-636
Fiber board box
4.02 x 2.33x 2.54 ft
20 lb
23.791 cu ft
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
Functioning
assembly.
NOTE
5-35
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
Packaging:
1377-01-037-9237
MS52
857AS400-107
(30003) 813475-107
116415-7
Item Weight -------------------- 0.183 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 22 in.
high fine silver
99.95%
A
Weight ------------------------- 0.001455 lb
Performance:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 4 x 32 in.
Weight ------------------------- 0.25 lb
Outer Container:

Minimum detonation
-65F (-54C)
References:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
5-36
PPP-B-566
Fiber board box
3.0 x 1.18 x .98 ft
15 lb
3.461 cu ft
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description: (General all sizes)
Functioning
assembly.
NOTE
physical appearance and design, The difference is in length and amount of explosive,
5-37
TM 43-0001-39
Tabulated Data:
part number -----------------
1377-01-037-4090
MS53
857AS400-109
(30003) 813475-109
116415-9
Item Weight -------------------- 0.132 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 18 in.
alloy sheathed
Type ---------------------------- HNS. type II. grade
A
Weight ------------------------- 0.001463 lb
Type ---------------------------- Bag. sealed

Dimensions ------------------- 24x 4 in.
Weight ------------------------Outer Container:

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-38
PPP-B-1672
Fiber board box
1.67 x 1.13x 0.58 ft
12 lb
1.907 cu ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385. App B
1.4
S
C
FLEXIBLE
LINEAR SHAPED
CHARGE,
HANDLE
CAREFULLY)
KEEP FIRE AWAY
TM 43-0001-39
Use:
Functioning
assembly.
NOTE
5-39
TM 43-0001-39
Tabulated Data
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-037-4096
MS54
857AS400-111
(30003) 813475-111
116415-11
Item Weight -------------------- 0.114 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 13 in.
alloy sheathed
A
Weight ------------------------- 0.001036 lb
Type ---------------------------- Bag, sealed

Dimensions - - - - - - - - - - - - - - - - 6 x 19 in.

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-40
PPP-B-1672
Fiber board box
1.75 x 1.08x 0.88 ft
12 lb
1.675 cu ft
References:
TM 9-1377-200-208zP
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
FLEXIBLE
LINEAR SHAPED
CHARGE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning:
assembly.
NOTE
5-41
TM 43-0001-39
Tabulated Data:
part number -----------------
1377-01-037-4095
MS55
857AS400-113
(30003) 813475-113
116415-13
Item Weight -------------------- 0.209 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 26 in.
alloy sheathed
A
Weight ------------------------- 0.001632 lb
Type ---------------------------- Bag, sealed

Dimensions ------------------- 6 x 48 in.
Weight ------------------------- 0.50 lb
Outer Container:

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-42
PPP-B-566
Fiber board box
2.83 x 1.67 x 0.83 ft
15 lb
3.923 cu ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
FLEXIBLE
LINEAR SHAPED
CHARGE,
HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning:
assembly.
NOTE
5-43
TM 43-0001-39
Tabulated Data
part number -----------------
1377-01-037-4094
MS56
857AS400-115
(30003) 813475-115
116415-15
Item Weight -------------------- 0.248 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 33 in.
high fine silver
99.95%
A
Weight ------------------------- 0.001852 lb
Type ---------------------------- Plastic bag

Dimensions ------------------- 6 x 46 in.
Weight ------------------------- 0.25 lb
Outer Container:

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-44
PPP-B-636
Fiber board box
3.48 x 1.58x 0.96 ft
15 lb
5.278 cu ft
References:
TM 9-1377-200-208zP
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning
assembly.
NOTE
5-45
TM 43-0001-39
Tabulated Data:
NSN ----------------------------- 1377-01-037-4093
DODIC --------------------------- MS57
part number ----------------- (30003) 116415-15
813475-115
Item Weight -------------------- 0.312 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 39 in.
high fine silver
99.95%
A
Weight ------------------------- 0.002270 lb
Type ---------------------------- Bag, heat sealed

Dimensions ------------------- 6 x 65 in.
Weight ------------------------- 0.50 lb
Outer Container:

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-46
PPP-B-636
Fiber board box
4.04 x 2.21 x 0.92 ft
20 lb
8.214 cu ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning:
assembly.
NOTE
5-47
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-032-3286
MS58
857AS400-119
(30003) 116415-19
813475-119
Item Weight -------------------- 0.1151b
Diameter ------------------------ 0.18 in.
Length --------------------------- 20 in.
high fine silver
99.95%
A
Weight ------------------------- 0.001036 lb

Dimensions ------------------- 4 x 22 in.
Weight ------------------------- 0.25 lb
Outer Container:

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-48
PPP-C-1672
Fiber board box
1.54 x 1.04x 0.27 ft
2.0 lb
0.464 cu ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning:
assembly.
NOTE
5-49
TM 43-0001-39
Tabulated Data
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-032-3283
MS59
857AS400-125
(30003) 116415-25
813475-125
Item Weight -------------------- 0,0197 lb
Diameter ------------------------ 0.18 in,
Length --------------------------- 27 in.
high fine silver
99.95%
A
Weight ------------------------- 0.0017631b

Dimensions ------------------- 4 x 43 in.
Weight ------------------------- 0,25 lb
Outer Container:

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-50
PPP-B-636
Fiber board box
3.33 x 1.75x 0.73 ft
15 lb
4.254 cu ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning:
assembly.
NOTE
5-51
TM 43-0001-39
Tabulated Data:
part number -----------------
1377-01-032-3279
MS60
857AS400-123
(30003) 116415-23
813475-123
Item Weight -------------------- 0.208 lb
Diameter ------------------------ 0.18 in.
Length --------------------------- 36 in.
high fine silver
99.95%
A
Weight ------------------------- 0.001609 lb
Type ---------------------------- Bag. heat sealed

Dimensions ------------------- 6 x 53 in.
Weight ------------------------- 0.25 lb
Outer Container:

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65 F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-52
PPP-B-636
Fiber board box
3.64 x 1.33x 0.64 ft
15.0 lb
3.098 cu ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning:
assembly.
NOTE
5-53
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-032-3280
MS61
857AS400-121
(30003) 116415-21
813475-121
Item Weight -------------------- 0.226 lb
Diameter ------------------------ 0.18 in,
Length --------------------------- 31 in.
high fine silver
99.95%
A
Weight ------------------------- 0.001543 lb
Type ---------------------------Dimensions ------------------Items per package ---------Weight ------------------------Outer Container:


Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-54
PPP-B-636
Fiber board box
2.96 X 1.25X 0.93 ft
12.0 lb
3.441 cu ft
Performance:
Bag, heat sealed

6 x 37 in.
1
0.25 lb
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
s
c
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
Use:
Description:
Functioning:
assembly.
NOTE
5-55
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-100-1718
MS62
857AS400-127
(30003) 116415-27
813475-127
Item Weight -------------------- 0.065 lb
Diameter ------------------------ 0.18 in,
Length --------------------------- 8 in.
high fine silver
99.95%
A
Weight ------------------------- 0.000727 lb

Dimensions ------------------- 4 x 16 in,
Weight ------------------------- 0.25 lb
Outer Container:

Performance:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-56
PPP-B-1672
Fiber board box
1.54 x 1.04x 0.27 ft
2.50 lb
0.432 cu ft
Reference:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
LINEAR EXPLOSIVE ASSEMBLY (LEA): (MS76)
Functioning:

Use:
The Linear-Explosive Assembly is used in
the AH-1 E/F/P helicopter to explosively sever
the canopy door hinge in an emergency.
NOTE
The MS76 and MS77 are identical in physical appearance to the M79, The difference is in length and amount of explosive.
5-57
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number ----------------Item Weight -------------------Diameter -----------------------Length --------------------------Method of actuation ---------
1377-01-032-1047
MS76
6261062
115362-1816986-1
0.344 lb
N/A
30.70 in.
High order detonation wave
alloy sheathed Propellant/explosive material:
A
Weight -------------------------
Performance:
Dimensions ------------------- 4 x 37 in.

Weight ------------------------- 0.25 lb
Outer Container:

Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-58
PPP-B-636
Fiber board box
3.25 x 0.79x 0.71 ft
10.00 lb
1.823 cu ft
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
FLEXIBLE
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
LINEAR EXPLOSIVE ASSEMBLY (LEA): (MS77)
Functioning:

Use:
The Linear-Explosive Assembly is used in
the AH-1 E/F/P helicopter to explosively sever
the canopy door hinge in an emergency.
NOTE
The MS76 and MS77 are identical in physical appearance to the M79, The difference is in length and amount of explosive.
5-59
TM 43-0001-39
Tabulated Data:
NSN ----------------------------- 1377-01-032-1048
DODIC --------------------------- MS77
Drawing number -------------- 6261062
pmt. number ----------------- 115362 -3816986-3
Item Weight -------------------- 0.0408 lb
Diameter ------------------------ N/A
Length --------------------------- 38.95 in.
alloy sheathed
A
Weight ------------------------- 0.006216 lb
Performance:
Dimensions ------------------- 4 x 44 in.

Weight ------------------------- 0.50 lb
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 4.00 x 0.81 x 0.73 ft
Weight ------------------------- 12.00 lb
Cube ---------------------------- 2.365 cu ft

Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-60
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
FLEXIBLE
LINEAR SHAPED
CHARGE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
LINEAR EXPLOSIVE ASSEMBLY, WINDOW (WCA): (MS78)
Functioning:
An explosive device used in the AH-1

E/F/P Helicopter Emergency Canopy Removal
linear explosive, extruded back-up cushion,
retainer, and seal.
The assemblies are located on the periphery of the four windows in the crew compartment.

the interconnecting LEA and SMDC lines to
force is outward? simultaneously cutting out
NOTE
The MS76 and MS77 are identical in physical appearance to the M79. The difference is in length and amount of explosive,
5-61
TM 43-0001-39
Tabulated Data:
part number -----------------
1377-01-032-1049
MS78
6261063
816987-103 1154069
Item Weight -------------------Diameter -----------------------Length --------------------------- 55.25 in.

alloy sheathed
A
Weight ------------------------- 0.005070 lb
Performance:


Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
5-62
PPP-B-636
Fiber board box
5.27 x 3.00x 0.75 ft
30.00 lb
11.850 cu ft
References:
TM 9-1377-200 -20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
MILD
DETONATING
FUSE, METAL
CLAD, HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
LINEAR-EXPLOSIVE ASSEMBLY, WINDOW (WCA): (MS79)
Use:
An explosive device used in the AH-1
E/F/P Helicopter Emergency Canopy Removal
Description:
linear explosive, extruded back-up cushion,
retainer, and seal.
Functioning:

the interconnecting LEA and SMDC lines to
the linear explosive of the WCA, The explosive
force is outward? simultaneously cutting out
NOTE
The MS78 is identical in design and physical appearance to the MS79. The difference is in length and amount of explosive.
5-63
TM 43-0001-39
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
Packaging:
1377-01-032-1050
MS79
6261063
816987-105
115405-7
Item Weight -------------------Diameter -----------------------Length --------------------------- 55.50 in.

alloy sheathed
A
Weight ------------------------- 0.005488 lb
Performance:
Inner Container:
Reference --------------------- MIL-B-117
Dimensions ------------------- 66x 35.5 in.
Weight ------------------------- 3 lb
Outer Container:

Minimum detonation
-65F (-54C)
References:
Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C)
5-64
PPP-B-636
Fiber board box
5.29 x 3.02 x 0.77 ft
30.00 lb
12.301 cu ft
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TB 9-1300-385, App B
1.4
S
C
HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
INERT CONNECTORS
Refer to helicopter subsystem.
Use:
Used in the AH-1 series helicopter canopy
release system as detonation transfer media
between detonating cord sequencing system
assemblies, and as a means to secure the assemblies to the aircraft structure.
Description:
Three types of inert connectors are used
as detonation transfers in the ballistic sequencing system: the tee, cross, and in-line (union).
There is one tee connector, mounted
behind the gunners seat which serves as a junction manifold for the crossover lines between
the right and left junction manifolds and the
interconnecting line assemblies from the nose

(external) armed/firing mechanism.
The system has two cross connectors, one
mounted in the upper right canopy structure
and the other mounted in the upper left canopy
structure. The cross connector mounted on the
left serves as a junction manifold for ballistic
sequencing assemblies between the pilots
armed/firing mechanism, the WCA for the gunners door, and the tee connector behind the gunners seat, The cross connector mounted on the
right serves as a junction manifold for ballistic
sequencing assemblies between the gunners
armed/firing mechanism, the WCA for the
pilots door, and the tee connector behind the
gunners seat.
There is one in-line connector mounted at
the forward bulkhead in the nose section which
serves as a connector union between the SMDC
assemblies interconnecting the nose (external)
armed/firing mechanism, and the junction manifold mounted behind the gunners seat.
5-65
TM 43-0001-39
Tabulated Data:
In-Line Connector:
Tee Connector:
NSN ----------------------------- 1377-01-062-4195

Drawing number -------------Vendor (CAGE Code) and
part number ----------------- 819397-103
Weight ---------------------------- 0.062 lb
Length --------------------------- 1.650 in.
Diameter ------------------------ 0.060 in.
Diameter (hex end
fittings) ------------------------ 0.075 in.
NSN ----------------------------- 1377-00-410-8228

part number ----------------- 813487-2 (30003)
209-030 -711-9
Weight ---------------------------- 0.112 lb
Length --------------------------- 1.680 in.
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.760 in.
Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.050 in.
Cross Connector:
NSN ----------------------------- 1377-00-409-1101
part number ----------------- 813488-1 (30003)
209-030-711-7
Weight ---------------------------- 0.196 lb
Length --------------------------- 1.680 in.
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.875 in.
Depth ----------------------------- 1.480
5-66
Service Life:
There is no specific service life for inert
connectors because they consist of metal parts,
(Refer to TB 9-1300-385, App B). However, due
to installation torques and possible damage during SMDC line removal, all connectors should
be checked for visible wear and tear and, if damaged, replaced.
Table 5-3 shows the detonating cord assemblies, inert connectors, and detonators used in
AH-1E/F/P/S (MOD) Army helicopters.
References:
TM 43-0001-39
CHAPTER 5
EMERGENCY ESCAPE SYSTEMS FOR
HELICOPTERS, AH-64
Section II. AH-64 (APACHE)
5-2. General (for Army AH-64 (Apache)
Helicopters).
a. Section 2 of this chapter contains
descriptive and technical data pertaining to the
systems used for the Army AH-64 Helicopter.
The system is used to explosively cut and eject
the windows of the canopy and doors from the
canopy and door framing structure to provide a
rapid means of escape and/or access from/to the
crew compartment.
b. The AH-64 emergency canopy jettison system consists of four linear explosive canopy severance assemblies which are installed
around the rim of the canopy windows and door
windows of the crew compartment. Also, three
armed/firing initiators (fig. 5-4) and interconnecting flexible confined detonating cord
(FCDC) and shielded mild detonating cord
(SMDC) lines. One arxned/firing initiator is
located in the pilots instrument panel to the
left of the glare shield, another is located in the
gunner/copilots right console, and the third is
in the nose of the helicopter which is located to
provide external access by rescue personnel.
Any one of the three armed/firing initiators can

be used to actuate the linear explosive escape
system.
c. The detonating cord set consists of
nine SMDC lines; five FCDC lines and four canopy severance assemblies.
This chapter
describes each assembly. Assemblies differ only
in length and explosive weight. Table 5-4 is a
list of the individual detonating cord lines, canopy severance assemblies and arming/firing initiators.
Each explosive item includes the
Department of Defense Identification Code
(DODIC), Hughes Helicopter P/N, National
Stock Number (NSN), Vendor Part Number,
Nomenclature, Drawing number, and explosive
weight.
d. This Section also contains descriptive information pertaining to the inert connectors in the AH-64 Helicopter canopy severance
system. Table 5-5 has inert items with the
National Stock Number, Vendor Part Number
(CAGE Code), Nomenclature, Drawing Number
and Quantity per helicopter.
5-67
TM 43-0001-39
Figure 5-3. AH-64 Emergency Canopy Jettison System Elements
5-68
TM 43-0001-39
TABLE 5-4. AH-64 HELICOPTER CANOPY SEVERANCE SYSTEM (EXPLOSIVE ITEMS)

**EXPLOSIVE
NSN 1377-01- TECHNOLOGY NOMENCLATURE
PART NO.
DODIC
*HUGHES
PART NO.
MS80
7-311112017-17
170-5244
51134-47
CORD, DETONATING
(SMDC)
841AS425-47
0.002028
51.0
MS81
7-311112017-15
170-5245
51134-53
CORD, DETONATING
(SMDC)
841AS425-53
0.000529
4.0
MS82
7311112017-13
170-5246
51134-51
CORD, DETONATING
(SMDC)
841AS425-51
0.001587
29.0
MS83
7-311112017-27
170-5261
51134-45
CORD, DETONATING
(SMDC)
841AS425-45
0.002601
59.0
MS84
7-311112017-25
170-5262
51134-57
CORD, DETONATING
(SMDC)
841AS425-57
0.001829
36.0
MS85
7-311112017-23
170-5263
51134-55
CORD, DETONATING
(SMDC)
841AS425-55
0.000816
9.0
MS86
7-311112017-21
170-5264
51134-23
CORD, DETONATING
(SMDC)
841AS425-23
0.000529
4.0
MS87
7-311112017-19
170-5265
51134-49
CORD, DETONATING
(SMDC)
841AS425-49
0.000772
8.0
MS88
7-311112017-29
186-9898
51134-35
CORD, DETONATING
(SMDC)
841AS425-35
0.000506
3.0
MS89
7-311112017-43
170-5260
51135-5
CORD, DETONATING
(FCDC)
6260906-5
0.003024
9.45
MS90
7-31111-2017-31
186-9899
51135-1
CORD, DETONATING
(FCDC)
6260906-1
0.004800
15.0
MS91
7-311112017-33
186.9900
51135-2
CORD, DETONATING
(FCDC)
6260906-2
0.007040
22.0
MS92
7-311112017-35
186-9901
51135-7
CORD, DETONATING
(FCDC)
6260906-7
0.005104
15.95
MS93
7-311112017-37
186-9902
51135-4
CORD, DETONATING
(FCDC)
6206906-4
0.004800
15.0
MS94
7-311112017-5
184-6112
51188-1
CUTTING ASSEMBLY
GUNNERS WINDOW
6206965-1
0.004321
7-311112017-7
MS95
47X34.5X1.5
185-6113
51390-1
CUTTING ASSEMBLY
6260965-3
0.004079
DRAWING
NO.
LENGTH
EXPLOSIVE
WEIGHT (LB) (INCHES)
71X24.5X1.5
PILOTS WINDOW
MS96
7-311112017-11
185-8908
51391-1
CUTTING ASSEMBLY
PILOTS DOOR
6260965-4
0.003814
44X33X1.5
MS97
7-311112017-9
187-4477
41389-1
CUTTING ASSEMBLY
GUNNERS DOOR
6260965-2
0.003946
66X23.5X1.5
MT06
7-311112017-39
2696496
51207.3
INITIATOR, MECH
ACTUATED JUA-59/A
6260964
0.000269
5.4X2.75X1.9
* CAGE Code element

** CAGE Code element
5-69
TM 43-0001-39
TABLE 5-5. AH-64 HELICOPTER CANOPY SEVERANCE SYSTEM (INSERT CONNECTORS)
*HUGHES
PART NO.
NSN 1377-01
**EXPLOSIVE
TECHNOLOGY
PART NO.
NOMENCLATURE
DRAWING
NO.
QTY PER
A/C
7-311112017-3
170-5319
21738-3
CONNECTOR, TEE
6261072
7-311112017-41
170-5321
21602-2
CONNECTOR, 180
DEGREE UNION
6261071
7-311112017-45
170-4493
23869-2
CONNECTOR ELBOW
6261073
* CAGE Code element

** CAGE Code element
5-70
TM 43-0001-39
Standard.
Use:
media to the canopy severance assemblies of
the crew compartments in the Emergency
Canopy Removal System of the AH-64 series helicopter.
Description:
are threaded fittings, seals, washers, inner and
Functioning:
and firing any one of the three armed/firing initiators, a detonation wave is received via the
junction manifold and is boosted by the loaded
booster shell. The stimuli from the booster actu-
ates the HNS within the SMDC assembly to the

adapter of the canopy severance assemblies.
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DODIC --------------------------Drawing number -------------CAGE Code and
part number -----------------
1377-01-170-5244
MS80
841AS42547
7-311112017-17
51134-47
Item Weight -------------------Dimensions --------------------Diameter -----------------------Length --------------------------- 51.0 in.

high fine silver
99.95%
Type ---------------------------- HNS, type I, grade
A
Weight ------------------------- 0.002028 lb
5-71
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 65 in,
Items per package ---------- 1 ea
Weight ------------------------- 0.31 lb
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 4.85 x 1.77 x 0.90 ft
Weight ------------------------- 20.0 lb
Cube ---------------------------- 7.73 cu ft
5-72

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B
1.4
S
C
CAREFULLY,
KEEP AWAY
FROM FIRE,
TM 43-0001-39
Standard.
Use:
Description:
Functioning:
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-170-5245
MS81
841AS425-53
7-311112017-15
51134-53
Item Weight -------------------Dimensions --------------------Diameter -----------------------Length --------------------------Method of actuation --------- High order detonation wave
high fine silver
99.95%
A
Weight ------------------------- 0.000529 lb
5-73
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65 F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 6 in,
Weight ------------------------- 0.04 lb
Outer Container:
5-74
PPP-B-636
Fiber board box
0.9 x 0.65x 0.65 in,
3.0 lb
0.38 cu ft

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CLASS C EXPLOSIVE. HANDLE
CAREFULLY,
KEEP AWAY
FROM FIRE,
TM 43-0001-39
Standard,
Use:
Description:
Functioning:
booster shell, The stimuli from the booster actu-

adapter of the canopy severance assemblies,
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1377-01-170-5246
DODIC --------------------------- MS82
CAGE Code and
part number ----------------- 7-311112017-13
51134-51
Item Weight -------------------Dimensions --------------------Diameter -----------------------Length --------------------------- 29.0
high fine silver
99.95%
A
Weight ------------------------- 0.001587 lb
5-75
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65 F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 45 in.
Weight ------------------------- 0.24 lb
Outer Container:
5-76
PPP-B-636
Fiber board box
2.98 x 0.98x 0.81 ft
15.0 lb
2.37 cu ft

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Standard.
Use:
Canopy Removal System of the AH-64 series helicopter,
Description:
sheathed mild detonating cord,
Functioning:

Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-170-5261
MS83
841AS425-45
7-311112017-27
51134-45

high fine silver
99.95%
A
Weight ------------------------- 0.002601
5-77
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 80 in,
Weight ------------------------- 0.43 lb
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 5.48 x 1.65 x 0.65 ft
Weight ------------------------- 15.0 lb
Cube ---------------------------- 5.84 cu ft
5-78

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Standard.
Use:
Description:
Functioning:

Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-170-5262
MS84
841AS425-57
7-311112017-25
51134-57

high fine silver
99.95%
A
Weight ------------------------- 0.001829 lb
5-79
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65 F (-54 C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 55 in,
Weight ------------------------- 0.28 lb
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 3.56 x 1.90x .98 ft
Weight ------------------------- 17.0 lb
Cube ---------------------------- 6.63 cu ft
5-80

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Standard.
Use:
the crew compartments in the Emergent
Description:
Functioning:

Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-170-5263
MS85
841AS425-55
7-311112017-23
51134-55

high fine silver
99.95%
A
Weight ------------------------- 0.000816 lb
5-81
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 20 in.
Weight ------------------------- 0.10 lb
Outer Container:
5-82
PPP-B-636
Fiber board box
1.31 x 0.90x 0.81 ft
9.0 lb
0.96 cu ft

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Standard.
Use:
Description:
Functioning:

Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377~01-170-5264
MS86
841AS425-23
7-311112017-21
51134-23

high fine silver
99.95%
A
Weight ------------------------- 0.000529 lb
5-83
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 8 in.
Weight ------------------------- 0.07 lb
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 0.90 x 0.65 x 0.65 ft
Weight ------------------------- 3.0 lb
Cube ---------------------------- 0.38 cu ft
5-84

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Standard.
Use:
Description:
Functioning:
booster shell, The stimuli from the booster actu-

Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-170-5265
MS87
841AS425-49
7-311112017-19
51134-49

high fine silver
99.95%
A
Weight ------------------------- 0.000772 lb
5-85
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 12 in.
Weight ------------------------- 0.09 lb
Outer Container:
5-86
PPP-B-636
Fiber board box
1.23 x 0.04x 0.90 ft
10.0 lb
1.04 cu ft

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Standard.
Use:
Description:
Functioning:

Tabulated Data:
--------------------NSN
part number -----------------
1377-01-186-9898
MS88
841AS425-35
7-311112017-29
51134-35

high fine silver
99.95%
A
Weight ------------------------- 0.000506 lb
5-87
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 8 in.
Weight ------------------------- 0.04 lb
Outer Container:
5-88
PPP-B-636
Fiber board box
0.90 x 0.65 x 0.65 ft
3.0 lb
0.38 cu ft

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TM 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
CORD, ASSEMBLY, DETONATING, FLEXIBLE CONFINED (FCDC): (MS89)
Tabulated Data:
Use:
the crew compartment doors and windows,
Description:
Major components of the flexible confined
detonating cord (FCDC) are housing, threaded
fittings, seals, charge case, Hexanitrostibene
(HNS), lead sheathed assembly
Functioning:
When the armed/firing initiators are actuated, the FCDC lines receive a detonating stimulus via a junction manifold and transmits it to
the canopy severance assemblies in the crew
compartments.
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-170-5260
MS89
6260906-5
7-311112017-43
51135-35
Item Weight -------------------Dimensions --------------------Diameter -----------------------Length --------------------------- 9.45 in.

alloy sheathed
B
Weight ------------------------- 0.003024 lb
5-89
TM 43-0001-39
Performance:
Temperature Limits:
When initiated, the energy output of the

FCDC shall be substantial enought to cause
0.020 inch minimum diametrical swelling of the
witness cap threaded onto the remote end of
the FCDC assembly.
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:

Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 6 x 12 in.
Weight ------------------------- 0.12 lb
Outer Container:
Reference --------------------- PPP-B-1672
Dimensions ------------------- 1.0 x .66x .21 ft
Weight ------------------------- 2.0 lb
Cube ---------------------------- 0.3 cu ft
5-90
References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Use:
the crew compartment doors and windows,
Description:
fittings, seals, charge case, Hexanitrostilbene
(HNS), lead sheathed assembly.
Functioning:
compartments.
Tabulated Data:
----------------NSN
part number -----------------
1377-01-186-9899
MS90
6260906-1
7-311112017-31
51135-1

alloy sheathed
B
Weight ------------------------- 0.004800 lb
5-91
TM 43-0001-39
Performance:
Temperature Limits:

FCDC shall be substantial enough to cause
the FCDC assembly.
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65 F (-54C)
Packaging:

Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 16 x 12 in.
Weight ------------------------- 0.14 lb
Outer Container:
Reference --------------------- PPP-B-1672
Dimensions ------------------- 1.5 x 1.0x 0.21 ft
Weight ------------------------- 2.0 lb
Cube ---------------------------- 0.4 cu ft
5-92
References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Tabulated Data:
Use:
the crew compartment doors and windows.
Description:
fittings, seals, charge case, Hexanitrostilbene
Functioning:
compartments.
NSN -------------- -----DODIC --------------------------Drawing number -------------CAGE Code and

part number -----------------
1377-01-186-9900
MS91
6260906-2
7-311112017-33
51135-2

alloy sheathed
B
Weight ------------------------- 0.007040 lb
5-93
TM 43-0001-39
Performance:
Temperature Limits:

the FCDC assembly.
Upper ----------------------------- +200F (+93 C)

Lower ----------------------------- -65F (-54C)
Packaging:

Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 24x 12 in.
Weight ------------------------- 0.18 lb
Outer Container:
Reference --------------------- PPP-B-1672
Dimensions ------------------- 1.1 x 1,1 x 0.30 ft
Weight ------------------------- 3.0 lb
Cube ---------------------------- 0.5 cu ft
5-94
References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM
43-0001-39
Tabulated Data:
Use:
Description:
fitting, seals, charge case, Hexanitrostilbene
Functioning:
compartments.
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-186-9901
MS92
6260906-7
7-311112017-35
51135-7
Item Weight -------------------Dimensions --------------------Diameter -----------------------Length --------------------------- 15,95

alloy sheathed
B
Weight ------------------------- 0.005104 lb
5-95
TM 43-0001-39
Performance:
Temperature Limits:

the FCDC assembly.
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:

Inner Container:
Reference --------------------Type ---------------------------Dimensions ------------------Items per package ---------Weight -------------------------
MIL.B.117
Bag, sealed
16x 12 in,
1 ea
0.15 lb
Outer Container:
Reference --------------------- PPP-B-1672
Dimensions ------------------- 1.5 x 1.0x 0.21 ft
Weight ------------------------- 3.0 lb
Cube ---------------------------- 0.4 cu ft
5-96
References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
Tabulated Data:
Use:
Description:
fittings, seals, charge case, Hexamtrostilbene
Functioning:
compartments.
NSN ----------------------------DODIC --------------------------Drawing number -------------CAGE Code and

part number -----------------
1377-01-186-9902
MS93
6260906-4
7-311112017-37
51135-4

alloy sheathed
B
Weight ------------------------- 0.004800 lb
5-97
TM 43-0001-39
Performance:
Temperature Limits:

the FCDC assembly.
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65 F (-54C)
Packaging:

Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 16x 12 in.
Weight ------------------------- 0.14 lb
Outer Container:
Reference --------------------- PPP-B-1672
Dimensions ------------------- 1.5 x 1,0x 0.21 ft
Weight ------------------------- 3.0 lb
Cube ---------------------------- 0.3 cu ft
5-98
References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
CANOPY SEVERANCE ASSEMBLY FORWARD PANEL: (MS94)
Use:
An explosive device used in the AH-64 helicopter emergency canopy severance system to
provide quick exit from, or access to the crew
compartments of the aircraft in an emergency
Description:
Major components of the canopy severance
assembly are charge retainer, charge holder,
sleeve booster, initiation block, linear explosive
and nameplate.
Functioning:
Upon actuation of the system by any one of
the armed/firing initiators, a detonation wave is
received via the interconnecting FCDC and

SMDC lines to the canopy severance assemblies. The explosive force of the linear explosive charge is outward, thus severing the plastic
panels of the crew compartments.
Tabulated Data:
NSN ------------------------------DODIC --------------------------Drawing number -------------CAGE Code and part
number ------------------------
1377-01-184-6112
MS94
6260965-1
7-311112017-5
51188-1
Item weight --------------------Dimensions ---------------------Diameter ------------------------Length ---------------------------Method of actuation ---------- High order detonation wave
alloy sheathed
Change 2 5-99
TM 43-0001-39
Material:
Weight -------------------------- 50.0 lb

Cube ---------------------------- 16.67 cu ft
Temperature Limits:
Weight -------------------------- 0.000269 lb

Performance:
Upper ----------------------------- +200F (+93C

Lower ----------------------------- -65F (-54C)
Minimum detonation
velocity ------------------------- 6050 meters/sec at
-65F (-54C)
Packaging:
Inner Container:
Reference ---------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 85 x 45 m.
Weight -------------------------- 1.83 lb
Outer Container:
Reference ---------------------- PPP-B-636
Dimensions ------------------- 6.65 x 2.56x 0.98 ft
5-100 Change 2
Quantity distance class ------ 1.4

group . . . . . . . . . . . . . . . . . . . . . . . . S
DOT designation -------------- CLASS C EXPLOSIVE, HANDLE
CAREFULLY,
KEEP AWAY
FROM FIRE
References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B
TM 43-0001-39
CANOPY SEVERANCE ASSEMBLY REAR (AFT) PANEL: (MS95)
Use:
compartments of the aircraft in an emergency.
Description:
Major components of the canopy severance
assembly are charge retainer, charge holder,
sleeve booster, initiation block, linear explosive
and nameplate.
Functioning:
Upon actuation of the system by any one of
the armed/firing initiators, a detonation wave is
received via the interconnecting FCDC and

SMDC lines to the canopy severance assemblies. The explosive force of the linear explosive charge is outward, thus severing the plastic
Tabulated Data:
NSN ------------------------------DODIC --------------------------Drawing number -------------CAGE Code and part
number ------------------------
1377-01-184-6113
MS95
6260965-3
7-311112017-7
51390-1
Item weight --------------------Dimensions ---------------------Diameter ------------------------Length ---------------------------Method of actuation ---------- High order detonation wave
alloy sheathed
Change 2 5-101
TM 43-0001-39
Material:
Type ---------------------------- ENS, type II, grade
Weight -------------------------- 50.0 lb

---------------------------- 14.85 cu ft
Temperature Limits:
Weight -------------------------- 0.004079 lb

Upper ----------------------------- +200F (+93C
Lower ----------------------------- -65F (-54C)
Performance:
Minimum detonation
velocity ------------------------- 6050 meters/see at
-65F (-54C)
Packaging:
Inner Container:
Reference ---------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 60 x 45 in.
Weight -------------------------- 1.66 lb

Quantity distance class ------ 1.4
group --------------------------- S
DOT designation -------------- CLASS C EXPLO-
SIVE, HANDLE
CAREFULLY,
KEEP AWAY
FROM FIRE
References:
Outer Container:
Reference ---------------------- PPP-B-636
Dimensions ------------------- 4.65 x 3.4x 0.94 ft
5-102 Change 2
TM 9-1377 -200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B
*U.S. GOVERNMENT PRINTING OFFICE: 1994- 546.043/00706
PIN 058915-002
TM 43-0001-39
CANOPY SEVERANCE ASSEMBLY REAR (AFT) PANEL: (MS96)
sive charge is outward, thus severing the plastic


Tabulated Data:
Use:
Description:
Major components of the canopy severance assembly are: charge retainer, charge
holder, sleeve booster, initiation block, linear
explosive and nameplate.
Functioning:
Upon actuation of the system by any one
of the armed/firing initiators, a detonation
wave is received via the interconnecting FCDC
and SMDC lines to the canopy severance assemblies, The explosive force of the linear explo-
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number -----------------
1377-01-185-8908
MS96
626095-4
7-311112017-11
51391-1
alloy sheathed
Type ---------------------------- HNS, type II grade
B
Weight ------------------------- 0.003814 lb
5-103
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
velocity ------------------------ 6050 meters/sec at
-65F (-54C)
Upper ----------------------------- +200oF (+93oC)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 60 x 45 in.
Weight ------------------------- 1.50 lb
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 4.35 x 3.27 x .94 ft
Weight ------------------------- 50.0 lb
Cube ---------------------------- 13.4 cu ft
5-104

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
CANOPY SEVERANCE ASSEMBLY FORWARD PANEL: (MS97)
sive charge is outward, thus severing the plastic


Tabulated Data:
Use:
Description:
Major components of the canopy severance assembly are: charge retainer, charge
holder, sleeve booster, initiation block, linear
explosive and nameplate.
Functioning:
Upon actuation of the system by any one
of the armed/firing initiators, a detonation
wave is received via the interconnecting FCDC
and SMDC lines to the canopy severance assemblies. The explosive force of the linear explo-
NSN ----------------------------DODIC --------------------------Drawing number -------------CAGE Code and

part number -----------------
1377-01-187-4477
MS97
6260965-2
7-311112017-9
51389-1
alloy sheathed
B
Weight ------------------------- 0.000269 lb
5-105
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 80 x 35 in.
Weight ------------------------- 1.75 lb
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 6.19 x 2.48 x .94 ft
Weight ------------------------- 50.0 lb
Cube ---------------------------- 14.4 cu ft
5-106

group --------------------------- S
DOT designation -------------- CLASS C EXPLOSIVE, HANDLE
CAREFULLY.
KEEP AWAY
FROM FIRE.
References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
TM 43-0001-39
ARMING/FIRING INITIATOR JUA-59: (MT06)
Use:
A mechanically actuated detonator-type initiator used to actuate the emergency canopy severance system on the AH-64 helicopter.
Description:
The arming/firing initiator is a mechanically actuated percussion-type detonator consisting of a body handle assembly, firing pin, M42
primer, a demolition transfer charge assembly,
seals and a fitting port.
Functioning:
The initiator handles are turned and
pushed to actuate the initiators. The handles
can be rotated in either direction 90 to arm
the initiator. As the handle is pushed, the
spring behind the firing pin is compressed. At

0.3 in. (0.76 cm) fo travel, lock balls release the
firing pin, and it strikes the primer. The
primer ignites the lead azide transfer charge,
which in turn ignites the main charge of HNS.
Tabulated Data:
NSN ----------------------------- 1377-01-269-6496
DODIC --------------------------- MT06
Drawing number -------------- 6260964
CAGE Code and
part number ----------------- 17610/51207-3
Item Weight -------------------Dimensions --------------------- 1.875 in.
Diameter ------------------------ 5.4 in.
Length --------------------------Method of actuation --------- Mechanical
Body Material ------------------ Steel
A
Weight ------------------------- 0.000269 lb
5-107
TM 43-0001-39
Performance:
Temperature Limits:
Minimum detonation
-65F (-54C)
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Bag, sealed
Dimensions ------------------- 8 x 12 in.
Weight ------------------------- 0.443 lb
Outer Container:
Reference --------------------- PPP-B-1672
Dimensions ------------------- 1.5 x 1.0 x 0.3 ft
Weight ------------------------- 3.0 lb
Cube ---------------------------- 0.5 cu ft
5-108

References:
TM 9-1377-200-20&P
TM 55-1520-238-23
TB 9-1300-385, App B.
1.4
S
C
CAREFULLY.
KEEP AWAY
FROM FIRE.
TM 43-0001-39
INERT CONNECTORS
CONNECTOR, ELBOW
Use:
Used in the AH-64 series helicopter canopy release system as detonation transfer
media between between system assemblies, and
as a means to secure the assemblies to the aircraft structure.
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1377-01-170-5319
Drawing no. -------------------- 6261073
CAGE code and part
no. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-311112017-45
23869-2
Quantity per Aircraft -------- 1
Description:
CONNECTOR, TEE
Three types of inert connectors are used

as detonation transfers in the system: the tee,
the elbow, and the union.
NSN ----------------------------- 1377-01-170-5319

Drawing no. -------------------- 6261072
CAGE Code and part
no. --------------- ----------------- 7-311112017-3
21738-3
Quantity per aircraft -------- 5
Tabulated Data:
CONNECTOR, IN-LINE, UNION
NSN ----------------------------- 1377-01-170-5321
Drawing no. -------------------- 6261071
CAGE Code and part
no. ----------------------------- 7-311112017-41
21601-2
Quantity per aircraft -------- 2
Service Life:
INERT - Item is assembly of metal part
only. Replacement is determined by On
Condition (OC), after inspection for visible
wear or defect.
5-109 (5-110 blank)
TM 43-0001-39
CHAPTER 6
IMPULSE CARTRIDGES
6-1 General
These cartridges shall be used only for their designated application.
a. The Impulse Cartridges described in

this chapter have a wide range of application,
characteristics, and physical appearances.
b. The Impulse Cartridges listed in this

chapter are grouped by their method of initiation; (1) electrical and (2) percussion.
6-1 (6-2 blank)
TM 43-0001-39
CARTRIDGE, IMPULSE, MARK 19 Mod 0: (MO12)
Type Classification
Refer to Aircraft Subsystem.
Use:
Used as the power source in stores
release/ejector systems on aircraft.
Description:
This is an electrically initiated, casegrounded, screw-in type cartridge, consisting of
a body, Mark 11 Mod 0 ignition element, hollow
metal plug and main charge, The open end is
crimped over a sealing disc. The electrode of
the ignition element is separated from the body
by an insulator. A hollow metal plug is
threaded inside the body, between the igniter
assembly and the propellant. The cartridge is
located in the firing breech of the mechanism it
is to operate.
Functioning:
When the cartridge is fired, the resulting
gas pressure operates the store release/ejector
mechanism.
Tabulated Data:
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
part number ----------------Item weight --------------------Diameter ------------------------
1377-00-793-9926
MO12
2164465
(10001) LD419700
0.038 lb (0.017 kg)
0.805 in.
(2.045 cm)
Length --------------------------- 1.471 in.
(3.736 cm)
Method of actuation --------- Electrical 5
amperes
6-3
TM 43-0001-39

Type --------------------------- Smokeless powder,
HPSK 5250.95
Weight ------------------------- 0.0021 lb (14.77
grains)
Weight ------------------------- 0.25 lb

Outer Container:
Reference --------------------- PPP-C-1672
Dimension -------------------- 1.54 x 1.04 x 0.27 ft
Weight ------------------------- 2.00 lb
Cube ---------------------------- .464 cu ft
Performance:
600 Explosive Power Rating
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- PPP-P-291
Dimension -------------------- 2.25 wide x 2.062
depth in. (6.41
wide x 5.24 depth)
6-4

group --------------------------- S
DOT designation -------------- Small Arms
Ammunition,
Handle Carefully,
Keep Fire Away
References:
TM 9-1377-200-20&P
TM 55-1510-204-23
TM 55-1510-213-23
TB 9-1300-385, App B
TM 43-0001-39
CARTRIDGE, IMPULSE: (M162)
Use:
To actuate a helicopter hoist cable cutter
to cut and release a steel hoist cable and its
load, in an emergency (CH-47).
Description:
The impulse cartridge is an electrically initiated cartridge. The contact pin which extends
from the firing end of the cartridge case is con-
nected to a wire within the powder chamber.

The other end of the wire is connected to the cartridge case adjacent to the steel cutting punch.
The design and contour of the cutting edge of
the captive cutting punch is such that the
punch cuts and wedges the severed ends of the
reeved portion of the hoist cable in the cutter to
prevent whiplash.
The cartridge is oriented to the correct

position in the cable cutter by a flat surface on
the rim of the cartridge case. This flat surface
ensures that the captive cutting punch strikes
the anvil of the cable cutter and wedges the
reeved end of the hoist cable.
6-5
TM 43-0001-39
Functioning:
Packaging:
When the cable cutter switch is operated,

electrical current initiates the cartridge in the
cable cutter. The expanding gas from the cartridge forces the punch against one side of the
cable as the other side of the hoist cable is
forced against the anvil in the cable cutter. The
cutting edge of the punch severs and releases
the cable and its load from the hoist. The cutting punch also secures the reeved end of the
hoist cable in the cable cutter. thus preventing
whiplash.
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Type 1 hermetically sealed metal
container
Dimensions ------------------- 2.625 x 2.625 1.5
in.
Outer Container:
Reference --------------------- PPP-C-1672
Dimensions ------------------- 17 x 12 x 9 in.
(43.18 x 30.48 x
22.86 cm)
Weight ------------------------- 2 lb
Cube ---------------------------- 0.464 cu ft
Tabulated Data:
NSN ------------------------------DODIC --------------------------Drawing number -------------Vendor (CAGE Code) and
part number ----------------Item weight --------------------Diameter -----------------------Length --------------------------Method of actuation ---------
1377-00-999-7463
M162
2518426
(40912) MSA96713
0.04 lb (0.02 kg)
0.500 in. (1.27 cm)
2.109 in. (5.36 cm)
Electrical 5
amperes
Type ---------------------------- Double base
Weight ------------------------- 0.0003 lb (2.10
grains)
Performance:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
6-6

group --------------------------- S
Ammunition, Class
C Explosive,
Handle Carefully,
Keep Fire Away
References:
TM 9-1377-200-20&P
TM 55-1520-209-23
TM 55-1520-227-23
TB 9-1300-385, App B
TM 43-0001-39
CARTRIDGE, IMPULSE: ARD-863-1 (M189)
Use:
For external stores ejection on the AH-1
series helicopter.
Description:
The ARD-863-1 Impulse Cartridge is a
standardized store ejection and release car-
tridge and consists of a cylindrical aluminum

alloy case and ignition element (electrode,
bridgewire, and ignition charge) and a separation disc. The CCU-44/B Impulse Cartridge
NSN-1377-01-033-2622 (MD66) is a suitable substitute for the ARD-863-1 (M189).
Functioning:
Upon receipt of an electrical signal the ignition element is fired and the resulting gas pressure ignites the main charge. When sufficient
pressure is developed, the closure disc ruptures
and the released gas pressure actuates the
release/ejector mechanism.
6-7
TM 43-0001-39
Tabulated Data:
NSN ----------------------------- 1377-01-057-0686
DODIC --------------------------- M189
Drawing number -------------- N/A
part number ----------------- (80236) ARD-863-1
(79495) P7911-2
Item weight --------------------Diameter ------------------------ 1.075 in.
(2.731 cm)
Length --------------------------- 1.03 in. (2.616 cm)
amperes
Type ---------------------------- Double base, 2.75
gm Booster
Charge, 1.15 gm
Weight ------------------------- 0.0090 lb (63
grains)
Dimensions ------------------- 3.5 x 3 (dia)

Weight ------------------------- 0.188 lb
(0.0853 kg)
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 8.25 x 8.25 x 14.5
in. (21 x 21 x
36.82 cm)
Weight ------------------------- 2 lb (0.9072 kg)
Cube ---------------------------- 0.57 cu ft
Performance:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
References:
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Type 1 hermetically sealed metal
container
6-8
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-237-23
TM 55-1520-236-23
TB 9-1300-385, App B
1.4
C
C
Small Arms
Ammunition, Class
C Explosive,
Handle Carefully,
Keep Fire Away
TM 43-0001-39
Use:
Used in the Holex cable cutter on the
Army CH-54A helicopter cargo hoist cable system.
Description:
The M253 Impulse Cartridge consists of a
steel case, two electrodes, bridgewire, ignition
element, main charge, and closure assembly.
The M253 is sometimes referred to as the explosive bolt.
6-9
TM 43-0001-39
Functioning:
Packaging:
Upon receiving an electric current, the

bridgewire attached to the electrical pins heats
and ignites the primer. The primer in turn
ignites the main charge. The pressure developed by the main charge propels the cutter
blade with sufficient force to sever the main
hoist cable, a 7/8-inch (2.22 cm) special steel
cable.
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Barrier bag
Dimensions ------------------- 8 x 5 in.
Weight ----------------------------- 0.25 lb
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 1.6 x 1.05 x 0.30 ft
Weight ------------------------- 2 lb
Cube ---------------------------- 0.464 cu ft
Tabulated Data:
NSN ----------------------------- 1377-00-878-6510
DODIC --------------------------- M253
part number ----------------- (10640) R 4181-1
Item weight --------------------Diameter ------------------------ 1 in. (2.54 cm)
Length --------------------------- 2.62 in. (6.67 cm)
Type ---------------------------- HI TEMP
Weight ------------------------- 0.004206 lb (29.442
grains)

Performance:
References:
TM 9-1377 -200 -20&P

TM 55-1520-209-23
TM 55-1520-227-23
TB 9-1300-385, App B
Upper ----------------------------- +160F (+71C)

Lower ----------------------------- -65F (-54C)
6-10
1.4
S
C
Explosive Release
Device, Class C
Explosive, Handle
Carefully, Keep
Fire Away
TM 43-0001-39
CARTRIDGE, IMPULSE, MARK 104 Mod 0: (M291)
ATC-S LCC-A.
Refer to Aircraft subsystem.
Use:
To actuate a telescoped catapult Ejection
Seat Trainer Device. The device is used to
train pilots and crew members on procedures to
be followed when ejecting from an aircraft during an emergency.
NOTE
Impulse cartridges Mark 103 Mod 0,
Mark 104 Mod 0 and Mark 3 Mod 1 are
identical in general appearance, diameter, and length. Each of these three
types of cartridges is designed for a different purpose and contains a different quantity of propellant. Impulse cartridge
Mark 104 Mod 0 shall be used only in the
catapult of the ejection seat trainer
device for which it was designed.
6-11
TM 43-0001-39
Description
The M291 Mark 104 Mod 0 Impulse
Cartridge case has a cup-type case crimped over
a head with an O-ring gasket for sealing. A lacquer sealed 50M percussion primer is recessed
in the head. The steel igniter tube is screwed
into the head and separated from the primer by a
brass washer. A steel plug is screwed into one
end of the igniter tube and is staked to a discshaped aluminum trap having holes for the
escape of the propellant gases.
Functioning
To operate the catapult, the trainee,
seated in the ejection seat of the training
device, reaches up with both hands and pulls
the handle of the face curtain at the top of the
seat. Movement of the curtain pulls a cable
which releases a spring-loaded firing pin at the
top of the catapult. Firing of the cartridge
builds up pressure in the catapult, thrusting
the seat and occupant upward along the rails
with a minimum of 6 gs, simulating the effect
of ejecting from an aircraft. The seat decelerates to a stop at a height of less than 20 feet
and before reaching the top of the tower.
Tabulated Data:
NSN --------------------------- ----- 1377-00-707-0590
DODIC --------------------------- M291
Drawing number -------------- 1863079
part number ----------------- (10001) LD491831
Length --------------------------- 5.42 in. (13.77 cm)
Type ---------------------------- Black powder, HES
5250
Weight ------------------------- 0.0705 lb (493.5
grains)
Performance:
18900 ft-lb Explosive Power Rating
6-12

Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
Packaging
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Type I hermetically-sealed metal
container
Dimensions ------------------- 6.0 x 2.532 in dia
(15.24 x 6.432 cm
dia)
Outer Container:
Reference --------------------- PPP-B-621
Type ---------------------------- Wood box
Dimensions ------------------- 13.375 x 9.0 x 7.25
in. (33.97 x 22.86 x
18.42 cm)
Weight ------------------------- 13 lb (5.897 kg)
Cube ---------------------------- 0.5 cu ft
References:
TM 9-1377-200-20&P
TB 9-1300-385, App B
1.4
C
C
Small Arms
Ammunition,
Handle Carefully,
Keep Fire Away
TM 43-0001-39
CARTRIDGE SET, IMPULSE, REDUCED CHARGE, PRIMARY: (M397)
Use:
The reduced charge cartridge set is in the
Martin-Baker ejection seat and consists of one
reduced charge primary catapult cartridge and
two secondary catapult cartridges which, when
fired in sequence, provide recoil forces and ballistic gases sufficient to eject the seat and its occupant from the aircraft in an emergency.
Description:
Components of the reduced charge primary catapult cartridge are copper disc, and
brass and rubber washers, metal case, and a percussion cap primer. Components of each of the
two secondary catapult cartridges are brass
cover with a 0.75-inch hole covered with a
0.003-inch thick copper disc, rubber sealing
ring, and brass case. The secondary cartridges
require no primer or booster.
Functioning:
The ejection process is actuated when the
occupant of the ejection seat pulls a fabric
blind, to which a cable is attached, down over
his face. This action causes the cable to with-
draw a sear from the firing mechanism of the

ejection gun which releases a spring-loaded firing pin. Movement of the firing pin initiates
the percussion primer of the primary catapult
cartridge; flame then passes through two vent
openings, igniting the booster, which ignites the
main charge of the primary catapult cartridge.
When the reduced charge primary catapult cartridge fires, recoil pressure forces the
inner tube to cam the springloaded plunger out
of the seat locking latch window. This latch
retains the ejection seat in the aircraft.
Inner and intermediate tubes of the ejection gun rise together, raising the ejection seat
away from the floor of the cockpit. After 14
inches of movement, a port in the outer tube is
uncovered, exposing the lower secondary catapult cartridge at the upper half of the barrel.
After a total movement of 39.35 inches, the
intermediate tube is stopped by a flange. These
firings eject the top unit of the barrel (together
with the seat and occupant) from the cockpit;
the two extended telescoping units remain
attached to the floor of the aircraft.
6-13
TM 43-0001-39
CARTRIDGE SET, IMPULSE, REDUCED CHARGE, PRIMARY: M397
6-14
TM 43-0001-39
Packaging:
Tabulated Data
NSN -------------------------------DODIC --------------------------Drawing number -------------Vendor (CAGE Code and
part number -----------------
1377-00-845-5242
M397
2519696
(MBEU) 26434-1 (1
ea) (MBEU)
29434-2 (2 ea)
Item weight --------------------- 0.03164 lb
(0.01435 kg)
Diameter ------------------------ Primary 1.843 in.
(4.681 cm)
Secondary 3.27 in.
(8.306 cm)
Length --------------------------- Primary 2.574 in.
(6.538 cm)
Secondary 0.610 in.
(1.549 cm)
Method of actuation --------- Primary - percussion primer;
Secondary - pressure and heat from
primary
Type ---------------------------- Nitrocellulose,
black powder
Weight ------------------------- 0.0815 lb (570.5
grains)
Performance:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
Inner Container:
Reference --------------------- MIL-P-116
Type ---------------------------- Type I
Hermetically sealed metal container
Dimensions ------------------- 3.27 x 3.27 x 3 in.
(8.306 x 8.306 x
7.62 cm)
Items per package ---------- 1 set
Weight ------------------------- 0.5 lb (0.227 kg)

1.4
S
C
EXPLOSIVE
POWER DEVICE,
CLASS C,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
References:
TM 9-1377-200-20&P
TM 55-1510-204-23
TM 55-1510-213-23
TB 9-1300-385, App B
6-15 (6-16 blank)
TM 43-0001-39
CARTRIDGE, IMPULSE DROGUE: (M507)
Use:
Used in a drogue gun on the MartinBaker ejection seat to automatically operate the
gun which releases two drogue parachutes after
the seat and occupant are ejected from the aircraft in an emergency escape.
Description:
Components of the drogue impulse cartridge are: metal case, percussion cap primer,
brass disc, and neoprene washer. The primer is
encased in tinfoil and requires no anvil. An
anvil is machined into the primer cavity of the
case.
Functioning:
When the ejection catapult ejects the seat
and occupant free of the aircraft, a trip rod
attached to the bulkhead removes a sear pin
from the drogue gun.
When the sear has been pulled, and a

mechanically induced delay time (determined
by sear series) has expired, the percussion cap
in the cartridge is fired by a blow from the firing pin actuated by a compression spring.
When the percussion cap fires, the gaseous
flame is forced through two vents leading to the
powder chamber, igniting the main charge. The
resultant gases expand and force a piston member out of the top of the drogue gun. As the piston leaves the gun, a shackle attached to the
top of the piston and to a drogue withdrawal
line, pulls out an 18-inch controller drogue (parachute) and a 60-inch stabilizer drogue from a
stowage compartment at the top of the seat.
Tabulated Data:
NSN --------------------------
1377-00-883-8997
1377-00-960-0453
DODIC --------------------------- M507
Drawing number -------------- 2520002
Vendor (CAGE Code and
part number ----------------- (MBEU) 7536-1
Item weight --------------------- 0.0922 lb (0.042
kg)
6-17
TM 43-0001-39
Diameter ------------------------ 0.705 in. (1.791

cm)
Length --------------------------- 2.420 in. (6.147
cm)
Type ---------------------------Weight ------------------------Performance:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Type I
Dimensions ------------------- 2.062 x 2.2 in. dia
Weight ------------------------- 0.167 lb (0.076 kg)
Outer Container:
6-18
Reference --------------------- PPP-B-621

Type ---------------------------- Wood box
Dimensions ------------------- 9.75 x 5.688 x
3.313 in (24,765 x
14.46 x 8.415 cm)
Weight ------------------------- 3 lb (31.361 kg)
Cube ---------------------------- 0.1 cu ft
group --------------------------- C
AMMUNITION,
CLASS C
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
References:
TM 9-1377-200-20&P
TM 55-1510-204-23
TM 55-1510-213-23
TB 9-1300-385, App B
TM 43-0001-39
CARTRIDGE, IMPULSE, GUILLOTINE: (M520)
Use:
Used in the guillotine firing unit on some
Martin-Baker Mark 5 series and some Mark 6
series ejection seats to furnish gas pressure for
actuation of the parachute withdrawal line guillotine.
Description:
Components of the guillotine cartridge
are: metal case, guillotine cartridge cap and
disc, a paper disc, and percussion cap primer.
The primer is encased in tin foil and
requires no anvil. An anvil is machined into
the primer cavity of the case. The primer is
force-fitted into the cartridge case to ensure contact between the tin foil and the anvil point.
The percussion cap is sealed in the head of the
case with dark purple lacquer.
6-19
TM 43-0001-39
Functioning:
Packaging:
When the manual override lever of the ejection seat is operated, the sear is withdrawn
from the guillotine firing unit and the firing pin
moves under strong spring pressure to strike
the percussion cap of the cartridge. The gas generated from the fired cartridge is fed via a stainless steel pipe and flexible hose to the
guillotine. When actuated, the guillotine severs
the nylon parachute withdrawal line.
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Type I
Dimensions ------------------- 2.63 x 2.63 x 3 in.
Weight ------------------------- 0.30 lb
Outer Container:
Reference --------------------- PPP-B-1672
Dimensions ------------------- 1.54 x 1.04 x 0.35 ft
Weight ------------------------- 3 lb (1.361 kg)
Cube ---------------------------- 0.11 cu ft
Tabulated Data:
NSN ----------------------------- 1377-00-883-8998
DODIC --------------------------- M520
Drawing number -------------- 2519698
Vendor (CAGE Code and
part number ----------------- (U1604) 16650-1
Item weight --------------------- 0.135 lb (0.062 kg)
Diameter ------------------------ 0.800 in. (2.03 cm)
Length --------------------------- 1.600 in. (4.1 cm)
Type ---------------------------- Nitrocellulose, gun
powder
Weight ------------------------- 0.00352 lb (24.64
grains)

group --------------------------- C
Ammunition,
Handle Carefully,
Keep Fire Away
Performance:
1410 ft-lb Explosive Power Rating
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
6-20
References:
TM 9-1377-200-20&P
TM 55-1510-204-23
TM 55-1510-213-23
TB 9-1300-385, App B
TM 43-0001-39
Use:
Used in the CH-54B helicopter to sever a
7/8-inch (2.22 cm) diameter stainless steel hoist
cable.
Description:
The M657 is used in the cable cutter NSN:
1377-00-178-8416. Two cutters are used in the
CH-54B helicopter. The cartridge consists of an
ignition element, body, and output charge. The
ignition element has an initiator body four-pin
electrical connector, two bridgewires and a
sleeve with a closure disc. The cartridge body
houses the ignition element and output charge.
A closure disc hermetically seals the output
charge within the cavity of the cartridge body.
Functioning:
Firing of the electrically initiated cartridge produces gas pressure to overcome the
sheer pin. The cutter blade is driven onto the
anvil cutting the cable that passes through the
cutter body.
Tabulated Data:
NSN ----------------------------- 1377-00-168-5802
DODIC --------------------------- M657
part number ----------------- (22567) 300051-1
Item weight --------------------Diameter ------------------------ 2 in. (5.08 cm)
Length --------------------------- 1.65 in. (4.17 cm)
6-21
TM 43-0001-39
Type ---------------------------- High Temperature
Smokeless Powder
Weight ------------------------- 0.0038 lb
Performance:
Outer Container:
Temperature Limits:
Upper ----------------------------- +165F (+74C)

Lower ----------------------------- -65F (-54C)

group --------------------------- S
DOT designation -------------- CLASS C
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
Dimensions ------------------- 8 x 6 in.
Weight ------------------------- 1 lb
6-22
References:
TB 9-1300-385, App B.
PPP-B-636
Fiberboard box
2.50 lb
0.560 cu ft
TM 43-0001-39
CARTRIDGE, IMPULSE, CCU-92/A: (MJ21)
charge that supplies the gas pressure for the

TCU-3/A Thruster.

Use:
Tabulated Data:
CCU-92/A is used as the power source for

the TCU-3/A Thruster.
NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1377-01-211-7211
DODIC --------------------------- MJ21
part number ----------------- (01276) FE7590-95
Length --------------------------- 0.88 in. (2.24 cm)
Type ---------------------------- Black powder
Weight ------------------------- 0.00052 lb (3.64
grains)
Description:
The impulse cartridge CCU-92/A is electrically initiated and consists of cylindrical aluminum body loaded phenolic spacer, main charge,
aluminum closure disc. Four insulated contact
pins complete the internal electrical circuit
through two separate bridgewires.
Functioning:
Upon receipt of firing current the bridgewires are fired which in turn fires the main
6-23
TM 43-0001-39
Performance:
Temperature Limits:
Upper ----------------------------- +200F (+93.4C)
Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Type I heretically
Weight -------------------------
6-24
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------Shipping and Storage Data:
group --------------------------- C
DOT designation -------------- Class C Explosive,
Handle Carefully,
Keep Fire Away
References:
TB 9-1300-385, App B.
TM 43-0001-39
CARTRIDGE, IMPULSE, M796: (MD73)
Tabulated Data:
ATC-S LCC-A.
Use:
Power source for the M1 chaff cartridge of
the M206 flare cartridge on a one to one match
which is used in the M130 dispenser pod on various aircraft.
Description:
The M796 cartridge consists of an aluminum case, header assembly, igniter charge,
booster charge, output charge, closure disc and
closure washer.
Functioning:
The impulse cartridge is fired electrically.
The resulting hot ballistic gases developed by
the impulse cartridge ignite the flare pellet causing the piston to expel the flare pellet from the
case.
NSN - - - - - - - - - - - - - - - - - - - - - - - - -- 1377-01-049-6365
DODIC --------------------------- MD73
Drawing number -------------- 9311660
part number ----------------- (14083) 9311660
Item weight --------------------- 0.278 lb (0.126 kg)
Diameter ------------------------ 0.625 in. (1.59 cm)
Length --------------------------- 0.50 in. (1.40 cm)
Type ---------------------------- HPC 1, M1911
Weight ------------------------- 0.0088 lb (61.6
grains)
Performance:
Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
6-25
TM 43-0001-39
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Type I,
Hermetically
Weight ------------------------- 1.67 lb (0.758 kg)
Outer Container:
Reference --------------------- PPP-B-636
Dimensions ------------------Weight ------------------------- 60 lb (27.22 kg)
6-26

group --------------------------- S
DOT designation -------------- ELECTRICAL
SQUIB, CLASS C
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
References:
TM 9-1377-200-20&P
TM 9-1095-206-13&P
TB 9-1300-385, App B.
TM 43-0001-39
CARTRIDGE, IMPULSE, CCU-44/B: (MD66)
CASE
ber of the ejection mechanism of a missile

launcher or bomb rack. The cartridge consists
of a case, electrode, ignition element, main
charge, and cap closure assembly.
Use:
Utilized as a power source for the ejection
of stores from aircraft/helicopter missile launchers and bomb racks. This cartridge is a suitable
substitute for the ARD-863-1, M189.
Description:
The CCU-44/B cartridge is an electrically
initiated cartridge installed in the firing cham-
Functioning:
Upon receipt of firing current the ignition
element is fired and the resulting gas pressure
ignites the main charge. When sufficient pressure is developed, the cup closure assembly ruptures and the released gas pressure actuates
the release/ejector mechanism.
6-27
TM 43-0001-39
Tabulated Data:
NSN -----------------------------
1377-01-063-3161
1377-01-063-3164
1377-01-063-3165
MD66
DODIC --------------------------Drawing Number ------------- (53711)
part number ----------------- 5184850
Item weight --------------------- 0.086 lb (0.04 kg)
Diameter ------------------------ 1.555 in.
(2.934 cm)
Length --------------------------- 1.155 in.
(2.934 cm)
amperes
Type ---------------------------- Double Base Nitro
Cellulose
Weight ------------------------- 0.01014 lb (70.98
grains)
Performance:
Upper ----------------------------- +225F (+107C)
Lower ----------------------------- -65F (-54C)
Dimensions ------------------- 4.13 x 6.19 in. dia

(10.49 x 15.723 cm
dia)
Items per package ---------- NSN 1377-01-0633161 = 60
NSN 1377-01-0633164 = 80
NSN 1377-01-0633165 = 10
Outer Container:
Reference --------------------- PP-B-1672
Type ---------------------------- Class II STYLE D
Dimensions ------------------- 2 x 1.33 x 0.35 ft
Weight ------------------------- 10 lb
Cube --------------------------- 0.78 cu ft

group --------------------------- C
AMMUNITION,
CLASS C
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
6-28
References:
TM 9-1377-200-20&P
TB 9-1300-385, App B
TM 43-0001-39
CHAPTER 7
INITIATORS/DETONATORS
(ARMING/FIRING MECHANISMS)
7-1. General
Initiators are explosive devices that use ballistic gas pressure or high order detonation
waves to start a chain of events or functions

within a system.
7-1 (7-2 blank)
TM 43-0001-39
ARMING/FIRING MECHANISM: P/N 813633-4
Use:
A detonator-type mechanism used in the
AH-1 series helicopter to actuate the canopy
removal system.
NOTE
Arming/Firing Mechanism PN 813633-4
to be replaced by 3W84, 1377-01-2340667.
Description:
The armed/firing mechanism is a manually operated percussion-type detonator assembly consisting of a body, handle assembly, firing
pin, compression spring, a demolition transfer/charge assembly quick release pin, seals,
fittings, and attaching hardware.
There are three armed/firing mechanisms
in the system, one each at the pilots and gunners stations and one in the fuselage nose for
external access by rescue personnel.
Functioning:
To actuate the system, the handle of the
armed/firing mechanism is rotated 90 degrees
counterclockwise to arm and pulled to fire a
primer charge initiating a detonation wave
which is transmitted through the system to detonate all four window cutting assemblies.
Tabulated Data:
NSN ----------------------------- 1377-00-410-8265
DODIC --------------------------Drawing number -------------- 813633-4
part number ----------------- (97499) 209-030711-37
(06331) 813633-4
Item weight --------------------- 2.5 lb (1.134 kg)
Width ----------------------------- 17 in. (17.8 cm)
Height ---------------------------- 5 in. (12.7 cm)
Length --------------------------- 12 in. (30.5 cm)
Method of actuation --------- Manually operated
B
Weight ------------------------- 0.000190 lb (1.33
grains)
Body material --------------- Steel
7-3
TM 43-0001-39
Performance:
Weight ------------------------- 2.5 lb

Cube ---------------------------- 0.562 cu ft

Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F (-54C
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
Dimensions ------------------- 6 x 11.5 in.
Weight ------------------------- 1lb
Outer Container:
Reference --------------------- PPP-B-621
Type ---------------------------- Wood box
Dimensions ------------------- 1.6 x 1.1 ft
7-4

group --------------------------- S
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TM 55-1520-236-23
TM 55-1520-239-23
TB 9-1300-385, App B
TM 43-0001-39
ARMING/FIRING MECHANISM: P/N 814033-101
Use:
A detonator-type mechanism used in the
AH-1 series helicopter to actuate the canopy
removal system.
NOTE
Arming/Firing Mechanism PN 814033101 to be replaced by 3W84, 1377-01-2340667.
Description:
The armed/firing mechanism is a manually operated percussion-type detonator assembly consisting of a body, handle assembly firing
pin, compression spring, a demolition transfer/charge assembly quick release pin, seals,
fittings, and attaching hardware.
There are three armed/firing mechanisms
in the system, one each at the pilots and gunners stations and one in the fuselage nose for
external access by rescue personnel.
Functioning:
To actuate the system, the handle of the
armed/firing mechanism is rotated 90 degrees
counterclockwise to arm and pulled to fire a
primer charge initiating a detonation wave
which is transmitted through the system to detonate all four window cutting assemblies.
Tabulated Data:
NSN ----------------------------- 1377-01-033-5088
DODIC --------------------------- N/A
Drawing number -------------- 814033-101
part number ----------------- 116-416-1
209-033-008-101
Length --------------------------- 7.9 in. (20.07 cm)
Method of actuation --------- Manual
Type ---------------------------- HNS
Weight ------------------------- 0.000190 lb (1.33
grains)
7-5
TM 43-0001-39
Performance:

group --------------------------- S
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
Upper ----------------------------- +200F (+93C)

Lower ----------------------------- -65F (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
Weight ------------------------- 1 lb
Outer Container:
Reference --------------------- PPP-621
Type ---------------------------- Wood box
Dimensions ------------------- 1.6 x 1.1 x 0.4 ft
Weight ------------------------- 2.5 lb
Cube ---------------------------- 0.562 cu ft
7-6
References:
TM 9-1377-200-20&P
TM 55-1520-221-23
TM 55-1520-234-23
TM 55-1520-236-23
TM 55-1520-239-23
TB 9-1300-385, App B
TM 43-0001-39
CHAPTER 8
ROCKET MOTORS/CATAPULTS
8-1. General
a. Rocket Motors and Rocket Catapults
are explosive devices used in various aircraft
egress systems to assist or propel the ejection
seat and its occupant from the aircraft in an

emergency situation.
b. This chapter contains technical data,
use, and description of rocket motors/rocket catapults.
8-1 (8-2 blank)
TM 43-0001-39
ROCKET MOTOR: (M447)
Functioning:

Use:
To provide stabilization and improved trajectories of the seat escape system.
Description:
The M119 tip-off compensation rocket
motor is designed for use in the Grumman OV1 Mohawk airplane on the MD-S5 seat system.
The unit provides sufficient energy to stabilize
the ejection seat in the correct attitude to
insure drogue chute deployment in the optimum direction.
The M119 rocket motor is trunnion

mounted under the seat. The nozzle is oriented
in a down position. A steel wire lanyard is
threaded into the firing mechanism and
attached to the cable dispenser which is
attached to the aircraft bulkhead.
After the lanyard is connected, the safety
pin is removed from the firing mechanism.
Once the escape system is actuated, the lanyard
automatically triggers the firing mechanism
and initiates the igniter assembly which, in
turn, ignites the propellant grain which provides the additional propulsion to the seat.
Performance:
Rocket Motor Performance

+65 to +75F
Min
Max
+160 to +165F
Min
Max
1800
1500
2300
1700
2700
370
430
370
430
370
430
Action Time (sec)
0.280
0.420
0.230
0.350
0.180
0.320
Burning Time (sec)
0.220
0.310
0.180
0.270
0.140
0.250
Ignition Delay Time (sec) 0.000
0.015
0.000
0.015
0.000
0.015
Parameter
Min
-65 to -70F
Max
Peak Thrust (lb)
1200
Total Impulse (lb-sec)
8-3
TM 43-0001-39

Upper ----------------------------- +160F (+71C)
Lower ----------------------------- -65F (-54C)
Tabulated Data:
NSN ----------------------------- 1377-00-244-1578
DODIC --------------------------- M447
Drawing number -------------- 11740301
Vendor (CAGE Code)
and part number ----------- (51998) 1044-2
Item weight --------------------- 6.36 lb (2.9 kg)
Diameter ------------------------ 4.202 in. (10.67
cm)
Length --------------------------- 13.3 in. (33.78 cm)
Method of actuation --------- Mechanical
Body material ------------------ 4130 steel and aluminum alloy
Type ---------------------------- High-density carboxy terminated
polybutadiene,
N-53 (U) MIL-P82676
Weight ---------------------------- 2.56 lb (17920
grains)
Packaging:
Inner Container:
Reference --------------------- PPP-B-636
8-4
Type ---------------------------- Fiberboard

Dimensions ------------------- (34.1 x 13.2 x 8.1
cm)
Weight ------------------------- 8 lb
Outer container:
Reference --------------------- PPP-B-621
Type ---------------------------- Wood box
Dimensions ------------------- 17 x 12-1/16 x 411/16 in. ((43.2 x
30.6 x 12 cm)
Weight ------------------------- 13 lb
Cube ---------------------------- 1.639 cu ft
group --------------------------- F
DOT shipping class ----------- B
DOT designation -------------- CLASS B
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
References:
TM 9-1377-200-20&P
TM 55-1510-204-23
TM 55-1510-213-23
TB 9-1300-385, App B
TM 43-0001-39
CHAPTER 9
THRUSTERS
9-1. General
a. A thruster is a component part of an
aircraft escape system or aerial delivery system,
which is used to accomplish a certain task prior
to implementing the final phases of escape, for
crewmen from a disable aircraft, or separation
of the components of an aerial delivery system.
b. The basic parts of a thruster consist

of a firing mechanism, cartridge, chamber and
piston. The main purpose of a thruster is to
impart a thrust to a known load or oppose a
force through a given travel (stroke).
9-1 (9-2 blank)
TM 43-0001-39
THRUSTER, CARTRIDGE ACTUATED, TCU-1/B: (MF24)
Type III A Release by Navy.
STD LCCA
aircraft initiates the CCU-57/B cartridge. After

the 0.4 second time delay, the TCU-1/B thruster
releases a tail cone which houses a recovery parachute. The aerodynamic load on the tail cone
thus serves to deploy the parachute.
Use:
Tabulated Data:
Used on the high speed aerial delivery system and receives its ballistic power from the
CCU-57/B Delay Cartridge.
NSN ----------------------------- 1377-01-075-6433

DODIC --------------------------- MF24
Drawing number -------------- 5184910
part number ----------------- 5184910
Item weight --------------------- 1.36 lb (0.62 kg)
Diameter -----------------------Length --------------------------- 9.0 in. (22.86 cm)
Method of actuation --------- Manual
Type ---------------------------- Black powder and
HES 5808
Weight ------------------------- 0.0025 lb (17.5
grains)
Note
TCU-1/B replaces XM5 thruster.
Description:
The TCU-1/B thruster consists of a cartridge (CCU-57/B), firing mechanism, body piston assembly, front and rear brackets and
safety pin.
Functioning:
When the CTU-2/A container is released
from the aircraft, an attached lanyard from the
9-3
TM 43-0001-39
Performance:
Delay time ---------------------- 0.4 sec +0.1
Minimum stroke
1.5 in. (3.81 cm)
Dimensions ------------------- 19 x 12-3/16 x 117/8 in. (48.3 x 30.46

x 30.16 cm)
Weight ------------------------Cube ---------------------------- 1.6 cu ft

Upper ----------------------------- +200F (+93C)
Lower ----------------------------- -65F 0 (-54C)
Packaging:
Inner Container:
Reference --------------------- PPP-B-636
Dimensions ------------------- 10-3/16 x 2-1/2 x 21/2 in. (25.9 x 6.4 x
6.4 cm)
Weight ------------------------- 1.6 lb (0.73 kg)
Outer Container:
Reference --------------------- PPP-B-621
Type ---------------------------- Wood Box
9-4

group --------------------------- S
POWER DEVICE,
CLASS C
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
References:
FM 10-547
TM 9-1377-200-20&P
TB 9-1300-385, App B
TM 43-0001-39
THRUSTER, CARTRIDGE ACTUATED, TCU-3/A: (MJ20)
Use:
UH-60 cargo hook release mechanism,
Provides a power source to release the load
applied to the 6,000 lb cargo hoist hook in the
event of an emergency.
Functioning:
The cargo hook cartridge assembly is fired
electrically by placing a switch in the crew compartment to the release position. Ballistic gas
pressure from the cartridge forces the piston
out of the body assembly thus mechanically operating the release mechanism on the cargo hook.
Description:
Tabulated Data:
The cartridge assembly for the cargo hook

consists of an aluminum body, a pressure cartridge, piston, plug, washer, piston retaining
ring and O-rings.
NSN ----------------------------- 1377-01-211-7212

DODIC --------------------------- MJ20
9-5
TM 43-0001-39

part number ----------------- (01270) FE 759098
Item weight --------------------- 0.21 lb
Diameter ------------------------ 0.735 in. (1.867
cm)
Length --------------------------- 253 in. (6.426 cm)
Type ---------------------------- SP
Weight ------------------------- 0.00052 lb (3.64
grains)
Performance:
Dimensions ------------------Item per package ----------- 1

Reference --------------------- PPP-B-636
Dimensions ------------------Weight ------------------------Cube ---------------------------Shipping and Storage Data
Upper ----------------------------- +200F (+93.4C)

Lower ----------------------------- -65C (-54C)
Packaging:
Inner Container:
Reference --------------------- MIL-C-10464
Type ---------------------------- Hermetically
9-6
References:
TM 9-1377-200-20&P
TM 55-1520-237-23
TB 9-1300-385, App B
1.4
S
C
EXPLOSIVE
POWER DEVICE,
CLASS C
EXPLOSIVE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
TM 43-0001-39
THRUSTER, EXPLOSIVE ACTUATED: P/N 209-033-007-3
Use:
Used on the AH-E/F/P Helicopter.
Description:
The thruster is a steel manifold that transmits an explosive force from shielded mild detonating cord (SMDC) to a thruster piston.
(Detonating cord provided at installation.)
Functioning:
Upon detonation of the SMDC the explosive force is applied to the piston driving it forward.
Tabulated Data:
NSN ----------------------------- 1377-01-062-4196
DODIC --------------------------Drawing number -------------- 820810
part number ----------------- (97499) 209-033007-3
Item weight --------------------- 0.37 lb
Diameter ------------------------ 0.88 in.
Length --------------------------- 4.78 in.
Method of actuation --------- Explosively
Initiated
Propellant/explosive material: None/Inert
Type ---------------------------- N/A
Weight ------------------------- N/A
9-7
TM 43-0001-39
Performance:
Quantity distance class -----
Upper ----------------------------- +200F (+93.4C)

Lower ----------------------------- -65C (-54C)
Packaging:
Reference ------------------------ MIL-B-117
Type ----------------------------- Heat sealed
Dimensions --------------------- 9 x 6 in.
Weight ---------------------------- 0.6 lb
Cube ----------------------------- 0.30 cu ft
9-8
group --------------------------DOT shipping class ----------DOT designation -------------References:
TB 9-1300-385, App B
TM 43-0001-39
CHAPTER 10
MISCELLANEOUS
10-1. General
a. The items listed in this chapter have
characteristics which set them apart from the
Cartridges, Cartridge Actuated Devices (CADs)
ITEMS
and Propellant Actuated Devices (PADs)

described in the other chapters of this manual.
b. Some of the items described in this
chapter are part of a kit or component and will
refer to the data sheet on such items.
10-1 (10-2 blank)
TM 43-0001-39
REFIRE KIT: 073-3831
Functioning:

part number ----------------- (22567) K303104-1
(82402) 42277E182
Length --------------------------- 6.0 in. (15.24 cm)
Type ---------------------------- Dupont bullseye
black powder
Weight ------------------------- 0.000243 lb (1,7
grains)
The Refire Kit is used to reload the UH-1

and UH-60 Cable Cutter.
Performance:
Tabulated Data:
NSN ----------------------------- 1377-01-073-3831

DODIC --------------------------Drawing number --------------
Upper ----------------------------- + 165F (+74 C)

Lower ----------------------------- -65F (-54C)

Use:
The refire kit is used to rebuild the cable
cutter on UH-1 and UH-60.
Description:
The refire kit consists of a cartridge assembly, shear pin, anvil, cutter, and two O-rings.
10-3
TM 43-0001-39
Packaging:
Inner Container:
Reference --------------------- PPP-B-636
Dimensions ------------------Items per package
Weight ------------------------- 0.3 lb
Outer Container:
Reference --------------------- PPP-B-621
Type ---------------------------- Wood box
Dimensions ------------------- 1.6 x 1.1 x 0.4 ft
Weight ------------------------- 2.5 lb
Cube ---------------------------- 0.560 cu ft

group --------------------------- S
POWER DEVICE,
HANDLE
CAREFULLY,
KEEP FIRE AWAY
References:
TB 9-1300-385, App B.
10-4
TM 43-0001-39
PIN PULLER, EXPLOSIVE ACTUATED P/N 816984
Use:
The pin puller is used in the AH-1 canopy
removal system(s).
Description
The Pin Puller is a steel manifold that
transmits an Explosive Force from shielded
mild detonating cord (SMDC) to a puller position.
Tabulated Data:
NSN ----------------------------- 1377-01-037-4091
DODIC --------------------------Drawing number -------------- 816984
part number ----------------- (06331) 816984
Length --------------------------- 2.25 in. (5.72 cm)
Method of actuation --------- Explosively actuated
Body Material ------------------ Steel
Propellant/explosive
material ----------------------- Not loaded - inert.
Performance:
Functioning:
Upon detonation of the SMDC, the explosive force is applied to the piston. Movement of
the piston pulls the pin that retains the canopy.

Upper ----------------------------- +200F (+93.4C)
Lower ----------------------------- -65F (-54C)
10-5
TM 43-0001-39
PIN PULLER, EXPLOSIVE ACTUATED: P/N 816984

Packaging:
Inner Container:
Reference --------------------- MIL-B-117
Type ---------------------------- Type I, class B
Dimensions ------------------- 4 x 6 in.
Weight ------------------------- 0.5 lb
Outer Container:
Reference --------------------- SPI (AMOP-01037-4091)
Type ---------------------------Dimensions ------------------- 0.6 x 0.5x 0.2 ft
Weight ------------------------- 0.5 lb
Cube ---------------------------- 0.046 cu ft
10-6
Quantity distance class ----- N/A

group --------------------------- N/A
DOT shipping class ----------- N/A
DOT designation -------------- N/A
References:
TM 9-1377-200-20&P
TM 55-1520-236-23
TB 9-1300-385, App B.
TM 43-0001-39
CARTRIDGE ASSEMBLY, CARGO HOOK: PY58
Use:
UH-60 cargo hook release mechanism.
Provides a power source to release the load
applied to the 8,000 lb cargo hoist hook in the
event of an emergency.
NOTE
To be replaced by CCU-921A Impulse
Cartridge MJ21 1377-01-211-7212
Description:
The cartridge assembly for the cargo hook
consists of an aluminum body, a pressure cartridge, piston, plug, washer piston retaining
ring and O-rings.
Functioning:
The cargo hook cartridge assembly is fired
electrically by actuating a switch in the crew
compartment to the release position. Ballistic

gas pressure from the cartridge forces the piston out of the body assembly thus mechanically
operating the release mechanism on the cargo
hook.
Tabulated Data:
NSN ----------------------------- 1377-01-149-5917
DODIC --------------------------- PY58
Drawing number -------------- FE7590-65
part number ----------------- (01276) FE7590-65
Length --------------------------- 2.36 in. (5.99 cm)
Type ---------------------------Weight ------------------------10-7
TM 43-0001-39
Performance:

group -------------------------- C
DOT designation -------------- Explosive Power
Device, Class C
Explosive, Handle
Carefully Keep
Fire Away.
Upper ----------------------------- N/A

Lower ----------------------------- N/A
Packaging:
Inner Container:
Reference --------------------Type ---------------------------Dimensions ------------------Items per package ---------Weight ------------------------Outer Container:
10-8
References:
TM 9-1377-200-20&P
TM 55-1520-237-23
TB 9-1300-385, App B
TM 43-0001-39
APPENDIX A
REFERENCE PUBLICATIONS
A-1. Army Regulations
Army Safety Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 385.10
System Safety Engineering and Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 385-16
Accident Reporting and Records . . . . . . . . . . . . . . . . ,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 385-40
Ammunition and Explosive Safety Standards .... .. . . . . . .. . . . . . . . . . . . . . . . . . . AR 385-64
Identification of Inert Ammunition and Ammunition Components . . . . . . . . . AR 385-65
Reporting of Transportation Discrepancies in Shipments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 55-38
Worldwide Ammunition Reporting System (WARS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 700-22
Ammunition Stockpile Reliability Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 702-6
Type Classification/Reclassification of Army Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 71-6
Report of Item and Packaging Discrepancies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 735-11-2
Malfunctions Involving Ammunition and Explosives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 75-1
Hazardous Item Contracts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . ... DARCOM-R 385-17
Determination and Assignment of Ammunition and Explosives
Hazard (classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DARCOM-R 385-21
Safety Manual .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DARCOM 385
Safety Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DARCOM 385-100
A-2. Technical Manuals

The Army Maintenance Management System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operators Aviation Unit Maintenance and Aviation Intermediate
Maintenance Manual Repair Parts and Special Tools List
(Incl RPSTL) Dispenser, General Purpose Aircraft: M130 . . . . . . . . . . . . . . . . . . . . .
Ammunition, General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ammunition and Explosive Standards ., . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ammunition Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..
Organizational and Maintenance Manual (Incl RPSTL) Cartridges,
Cartridge Actuated Devices and Propellant Actuated Devices.
Aviation Unit and Intermediate Maintenance Manual:
Army Models OV-1B/OV-1C Aircraft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Army Models OV-1D/RV-1D Aircraft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aviation Unit and Aviation Intermediate Maintenance Manual:
Army Model CH-47A Helicopter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aviation Unit and Intermediate Maintenance Instructions:
Army Model UH-1D/H/V/EH-1H Helicopters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CH-54A Helicopter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . .
Army Model UH-1C/M Helicopters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DA PAM 738-750
TM
TM
TM
TM
9-1095-206-13&P
9-1300-200
9-1300-206
9-1300-250
TM 9-1377-200-20&P
TM 55-1510-204-23
TM 55-1510-213-23
TM 55-1520-209-23
TM 55-1520-210-23
TM 55-1520-217-23
TM 55-1520-220-23
A-1
TM 43-0001-39
]Aviation Unit and Aviation Intermediate Maintenance Manual:

Army Model AH-1G and AH-1Q Helicopters .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 55-1520-221-23
Army Model CH-47B and CH-47C Helicopters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 55-1520-227-23
Avum and Avim Maintenance Manual: AH-1S (MOD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 55-1520-234-23
Army Model AH-IS (PROD), AH-IS (ECAS) and AH-1S
(Modernized COBRA) Helicopters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 55-1520-236-23
Aviation Unit and Intermediate Maintenance Wiring Data
Manual for UH-60A Helicopter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 55-1520-237-23
Aviation Unit and Intermediate Maintenance Repair Parts and
Special Tools List (Incl Depot Maintenance RPSTL) for
Helicopter, Attack, AH-1S (Modernized COBRA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 55-1520-239-23
CH-47D Helicopter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 55-1520-240-23
A-3. Technical Bulletins

Department of Defense Explosive Hazard Classification Procedures. . . . . . . . . . . . TB 700-2
Munitions Suspended or Restricted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB 9-1300-385-1
Munition Permanently Suspended or Restricted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB 9-1300-385-2
A-4. Supply Catalogs

DOD Consolidated Ammunition Catalog. . . . . . . . . . . . . . . . . . . . . . SB 708-4
A-5. Blank Forms

Recommended Changes to Publications and Blank Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DA Form 2028
Ammunition Condition Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DA Form 2415
Accident Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DA form 285
SF 361
Discrepancy in Shipment Report . . . . . . . . . . . . . . . .. . . . . . . . ..
Packaging and Improvement Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SF 364
A-6. Navy Publications

Ordnance Safety Precautions, Their Origin and Necessity. . . . . . . . . . . . . . . . . . . . . .OP 1014
Index to Navy Ammunition Stocks, Cartridges and Cartridge
Actuated Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . .TW010-AA-ORD-010
Navy Transportation Safety Handbook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OP 2165
United States Navy Ordnance Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OP 3347
Ammunition Afloat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OP 4
Ammunition and Explosives Ashore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OP 5
A-2
TM 43-0001-39
APPENDIX B
CAD/PAD
AIRCRAFT/HELICOPTER/EQUIPMENT
CROSS REFERENCE
CAD/PAD
Arm-Fire Initiator
Cartridge, Aricraft
Cartridge, Aircraft
Cartridge, Aircraft
Cartridge, Aircraft
Fire
Fire
Fire
Fire
NSN
Extinguisher
Extinguisher
Extinguisher
Extinguisher
Cartridge, Aircraft Fire Extinguisher
1377-01-033-5088
1377-00-087-7103
1377-00-756-1384
1377-00-824-5858
1377-00-930-9390
Cartridge,
Cartridge,
Cartridge,
Cartridge,
Cartridge,
Aircraft Fire Extinguisher

Assembly Cargo Hook
Assembly Cargo Hook
Delay
Delay
1377-01-113-8530
1377-01-263-3627
1377-01-185-2622
1377-01-115-3711
1377-01-149-5917
1377-00-774-7259
1377-00-958-1048
Cartridge,
Cartridge,
Cartridge,
Cartridge,
Delay
Impulse
Impulse
Impulse
1377-01-084-6064
1377-00-168-5802
1377-00-253-4436
1377-00-585-9291
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Set, Impulse
Cartridge, Impulse
Connector, Inline (Inert)
1377-00-707-0590
1377-00-793-9926
1377-00-805-9281
1377-00-878-6510
1377-00-883-8997
1377-00-883-8998
1377-00-999-7463
1377-01-049-6365
1377-01-057-0686
1377-01-063-3161
1377-01-063-3164
1377-01-063-3165
1377-01-211-7211
1377-00-845-5242
1377-00-062-4195
Cord,
Cord,
Cord,
Cord,
Cord,
Cord,
Cord,
Cord,
Cord,
Cord,
1377-00-409-1098
1377-00-409-1099
1377-00-409-1100
1377-00-410-8266
1377-00-410-8271
1377-00-410-8289
1377-00-410-8297
1377-01-032-1047
1377-01-032-1048
1377-01-032-1049
Detonating
Detonating
Detonating
Detonating
Detonating
Detonating
Detonating
Detonating
Detonating
Detonating
APPLICATION
AH-E/F/P (Cobra)
CH-47 (Chinook)
OV-1 (Mohawk)
CH-47 (Chinook)
AH-1 (Cobra)
UH-60A (Blackhawk)
UH-60A (Blackhawk)
UH-60A (Blackhawk)
20 sec delay
Cargo Parachute
TCU-1/B Thruster
CH 54B
AH-S(MOD)
AH-1S/MOD
AH-1S/MOD
AH-1S/MOD
E/F/P (Cobra)
E
F
P
OV-1A (Mohawk)
OV-1 (Mohawk)
OV-1 (Mohawk)
UH-60A (Blackhawk)
UH-60A (Blackhawk)
UH-60A (Blackhawk)
UH-60A (Blackhawk)
TCU-3/A Thruster
OV-1 (Mohawk)
AH-1E/F/P (Cobra)
AH-1S/MOD E
AH-1S/MOD F
AH-1S/MOD P
AH-1S (MOD)
AH-1S (MOD)
AH-1S (MOD)
AH-1S (MOD)
AH-1S (MOD)
AH-1S (MOD)
AH-1S (MOD)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
B-1
TM 43-0001-39
CAD/PAD
NSN
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cutter Assembly
Cutter, Cartridge Actuated
Cutter, Reef Line
1377-01-032-1050
1377-01-032-3279
1377-01-032-3280
1377-01-032-3283
1377-01-032-3286
1377-01-035-4124
1377-01-037-4090
1377-01-037-4093
1377-01-037-4094
1377-01-037-4095
1377-01-037-4096
1377-01-037-9237
1377-01-064-4927
1377-00-412-4377
1377-01-087-5166
1377-00-060-0885
Cutting Assembly
Cutting Assembly
Cutting Assembly
Cutting Assembly
Firing Mechanism
Interconnecting Line
Junction Manifold (Inert)
Refire Kit
Rocket Motor
Thruster, Cartridge Actuated
1377-00-106-7773
1377-00-409-1095
1377-00-409-1096
1377-00-409-1097
1377-00-410-8265
1377-01-100-1718
1377-00-409-1101
1377-00-410-8228
1377-01-037-4092
1377-01-037-4091
1377-01-073-3831
1377-00-244-1578
1377-01-075-6433

Thruster, Explosive
1377-01-211-7212
1377-01-062-4196
B-2
APPLICATION
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
UH-1 (Iroquois)
CH-54 (Tarhe)
High Speed Aerial
Deliver, CTU-2A
AH-1S (MOD) (Cobra)
AH-1S (MOD) (Cobra)
AH-1S (MOD) E/F/P (Cobra)
AH-1S (MOD) (Cobra)
AH-1S (MOD) E/F/P (Cobra)
AH-1S (MOD) (Cobra)
AH-1S (MOD) (Cobra)
AH-1S (MOD) (Cobra)
AH-1 E/F/P (Cobra)
AH-1 E/F/P (Cobra)
UH-1 (Iroquois)
OV-1 (Mohawk)
High Speed Aerial
Delivery, CTU-2A
UH-60A (Blackhawk)
AH-1E/F/P (Cobra)
TM 43-0001-39
Figure B-1. Designation of Rotary Wing Army Aircraft (sheet 1 of 2).
B-3
TM 43-0001-39
Figure B-1. Designation of Rotary Wing Army Aircraft (sheet 2 0f 2).
B-4
TM 43-0001-39
Figure B-2. Designation of Fixed Wing Army Aircraft (sheet 1 of 2).
B-5
TM 43-0001-39
Figure B-2. Designation of Fixed Wing Army Aircraft (sheet 2 of 2).
B-6
TM 43-0001-39
APPENDIX C
AIRCRAFT/HELICOPTER/EQUIPMENT TO CAD/PAD
CROSS-REFERENCE
Type - Aircraft
Equipment
AH-IS (MOD)
CAD/PAD
NSN
DODIC
Cartridge, Impulse
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cutting, Assembly
Cutting, Assembly
Cutting, Assembly
Cutting, Assembly
Firing Mechanism
Junction Manifold (Inert) Cross
Junction Manifold (Inert) Tee
1377-00-585-9291
1377-00-409-1098
1377-00-409-1099
1377-00-409-1100
1377-00-410-8222
1377-00-410-8266
1377-00-410-8271
1377-00-410-8289
1377-00-410-8297
1377-00-106-7773
1377-00-409-1095
1377-00-409-1096
1377-00-409-1097
1377-00-410-8265
1377-00-409-1101
1377-00-410-8228
M189
MD18
MD16
MS50
Cartridge, Impulse
Connector, Inline
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Junction, Manifold (Inert) Inline
Thruster, Explosive
1377-00-585-9291
1377-01-062-4195
1377-01-032-1047
1377-01-032-1048
1377-01-032-1049
1377-01-032-1050
1377-01-032-3279
1377-01-032-3280
1377-01-032-3283
1377-01-032-3286
1377-01-035-4124
1377-01-037-4090
1377-01-037-4093
1377-01-037-4094
1377-01-037-4095
1377-01-037-4096
1377-01-037-9237
1377-01-037-4092
1377-01-037-4091
1377-01-062-4196
M189
MS76
MS77
MS78
MS79
MS60
MS61
MS59
MS58
MS51
MS53
MS57
MS56
MS55
MS54
MS52
AH-1 E/F/P
Cord, Detonating
Initiator, Arm-Fire
1377-01-100-1718
1377-01-033-5088
MS62
AH-64
Connector, Elbow
Connector, Union
Connector, Tee
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
1377-01-170-4493
1377-01-170-5321
1377-01-170-5319
1377-01-186-9899
1377-01-186-9900
1377-01-186-9901
1377-01-186-9902
AH-1 E/F/P
MS47
MD15
MS48
MD17
MD35
MD34
MD33
MD36
MS90
MS91
MS92
MS93
C-1
TM 43-0001-39
Type - Aircraft
Equipment
DODIC
CAD/PAD
NSN
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cord, Detonating
Cutting Assembly
Cutting Assembly
Cutting Assembly
Cutting Assembly
Initiator, Mechanical
1377-01-170-5260
1377-01-170-5245
1377-01-170-5246
1377-01-170-5244
1377-01-170-5265
1377-01-170-5264
1377-01-170-5263
1377-01-170-5262
1377-01-170-5261
1377-01-186-9898
1377-01-184-6112
1377-01-184-6113
1377-01-187-4477
1377-01-185-8908
1377-01-269-6496
MS89
MS81
MS82
MS80
MS87
MS86
MS85
MS84
MS83
MS88
MS94
MS95
MS97
MS96
MT06
Cargo Parachute
Cartridge, Delay
1377-00-958-1048
M308
CH-46, CH-47
Cartridge, Aircraft Fire

Extinguisher
1377-00-756-1384
M182
CH-47

Extinguisher
Cartridge, Impulse
1377-00-930-9390
M193
1377-00-999-7463
M162
CH-54
Cartridge, Impulse
1377-00-168-5802
1377-00-412-4377
M657
M554
CTU-2/A, TCU-1/B
Cartridge, Delay
Cutter, Reef Line
1377-01-084-6046
1377-00-060-0885
1377-01-075-6433
MF35
M500
MF24
OV-1

Extinguisher
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge Set, Impulse
Rocket Motor
Parts Kit, Cutter
1377-00-930-9390
UH-1
Parts Kit, Cutter

Refire Kit
1377-00-011-9082
1377-01-073-3831
UH-60

Extinguisher
Cartridge, Pressure Cargo Hook
Cartridge, Impulse ARD 863-1
Extinguisher
Cartridge, Impulse CCU-44/B
1377-01-113-8530
C-2
1377-00-793-9926
1377-00-883-8997
1377-00-883-8998
1377-00-845-5242
1377-00-244-1578
1377-00-011-9082
M012
M507
M520
M397
M447
1377-01-115-3711
1377-01-057-0686
1377-01-263-3627
M189
MT20
1377-01-063-3164
MD66
TM 43-0001-39
APPENDIX D
CAD/PAD INDEX BY DODIC
DODIC
NOMENCLATURE
M162
M182
M189
M193
M232
M253
M291
M308
M397
M447
M500
M507
M520
M554
M657
M721
MD15
MD16
MD17
MD18
MD33
MD34
MD35
MD36
MD66
MD73
MF24
MF35
MF90
MF92
MH88
MH92
MJ20
MJ21
MO12
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Delay M252
Cartridge Set, Impulse Reduced
Rocket Motor M119
Cutter, Reef Line M21
Cartridge, Impulse Drogue
Cartridge, Impulse Guillotine
Cartridge, Impulse
Cartridge, Delay
Cord, Detonating (FCDC)
Cord, Detonating (SMDC)
Cutting Assembly (WCA)
Cutting Assembly, (WCA)
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Delay CCU-57/B
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Delay
Cartridge, Impulse CCU-92/A
Cartridge, Impulse Mk 19 Mod 0
PAGE
6-5
2-3
6-7
2-5
2-7
6-9
6-11
4-7
6-13
8-3
3-3
6-17
6-19
3-5
6-21
See 20 & P
5-9
5-11
5-13
5-15
5-17
5-19
5-21
5-23
6-27
6-25
9-3
4-3
See 20 & P
See 20 & P
4-5
2-9
9-5
6-23
6-3
D-1
TM 43-0001-39
DODIC
MS47
MS48
MS49
MS50
MS51
MS52
MS53
MS54
MS55
MS56
MS57
MS58
MS59
MS60
MS61
MS62
MS76
MS77
MS78
MS79
MS80
MS81
MS82
MS83
MS84
MS85
MS86
MS87
MS88
MS89
MS90
MS91
MS92
MS93
MS94
MS95
MS96
MS97
MT06
MT20
MU02
MU03
MU11
PY58
D-2
NOMENCLATURE
Linear Explosive Assembly (LEA)
Linear Explosive Assembly Window (WCA)
Canopy Severance Assembly Forward Panel
Canopy Severance Assembly Rear Panel
Arming/Firing Initiator
Cutter, Assembly
Cutter, Delay, Propellant Actuated MLU-58/B
Cartridge Assembly Cargo Hook
PAGE
5-25
5-27
5-29
5-31
5-33
5-35
5-37
5-39
5-41
5-43
5-45
5-47
5-49
5-51
5-53
5-55
5-57
5-59
5-61
5-63
5-71
5-73
5-75
5-77
5-79
5-81
5-83
5-85
5-87
5-89
5-91
5-93
5-95
5-97
5-99
5-101
5-103
5-105
5-107
2-11
3-7
3-9
3-11
10-7
TM 43-0001-39
APPENDIX E
CAD/PAD INDEX BY NSN
NSN 137700-087-5326
00-060-0885
00-087-7103
00-106-7773
00-168-5802
00-244-1578
00-253-5536
00-328-8080
00-409-1095
00-409-1096
00-409-1097
00-409-1098
00-409-1099
00-409-1100
00-409-1101
00-410-8222
00-410-8228
00-410-8265
00-410-8266
00-410-8271
00-410-8289
00-410-8297
00-412-4377
00-508-2464
00-585-9291
00-707-0590
00-756-1384
00-774-7259
00-793-9926
00-805-9281
00-824-5858
00-845-5242
00-878-6510
00-883-8997
00-883-8998
00-930-9390
00-958-1048
00-978-7644
00-999-7463
00-999-7465
01-032-1047
01-032-1048
01-032-1049
01-032-1050
01-032-3279
01-032-3280
NOMENCLATURE
Cutter Propellant Actuated Mk 20 Mod 0
Cartridge Aircraft Fire Extinguisher
Cutting Assembly Gunners Door Window
Cartridge, Impulse
Rocket Motor
Cartridge, Impulse
Firing Mechanism
Cutting Assembly Gunners Canopy Window
Cutting Assembly Pilots Canopy Window
Cutting Assembly Pilots Door Window
Junction, Manifold (Inert)
Junction, Manifold (Inert)
Armed/Firing Mechanism
Cartridge, Impulse ARD-863-1
Cartridge, Impulse MK 104 Mod 0
Cartridge, Delay
Cartridge, Impulse MK 19 Mod 0
Cartridge, Impulse
Cartridge Set, Impulse Reduced Charge
Cartridge, Impulse
Cartridge, Impulse Guillotine
Cartridge, Delay
Cartridge, Impulse
Cartridge, Impulse
Cord, Detonating (LSC)
Cord, Detonating (LSC)
Cord, Detonating Window Cutting Assembly
Cord, Detonating Window Cutting Assembly
DODIC
M648
M500
M232
MD35
M657
M447
MF90
MD34
MD33
MD36
MD18
MD16
MS50
MS49
MS47
MD15
MS48
MD17
M554
M500
M189
M291
M182
MO12
MF92
M232
M397
M253
M507
M520
M193
M308
MDO1
M162
MS76
MS77
MS78
MS79
MS60
MS61
E-1
TM 43-0001-39
NSN 137701-032-3283
01-032-3286
01-032-5088
01-035-4124
01-037-4090
01-037-4091
01-037-4092
01-037-4093
01-037-4094
01-037-4095
01-037-4096
01-037-9237
01-049-6365
01-057-0686
01-060-8531
01-062-4195
01-062-4196
01-063-3161
01-063-3164
01-063-3165
01-064-4927
01-073-3831
01-075-6433
01-084-6046
01-087-5166
01-100-1718
01-113-8530
01-115-3711
01-141-9028
01-149-5917
01-185-2622
01-211-7211
01-170-4493
01-170-5244
01-170-5245
01-170-5246
01-170-5260
01-170-5261
01-170-5262
01-170-5263
01-170-5264
01-170-5265
01-170-5319
01-184-6112
01-184-6113
01-185-8908
01-186-9898
01-186-9899
E-2
NOMENCLATURE
Armed/Firing Mechanism P/N 814033-101
Pin Puller Explosive
Junction, Manifold (INERT)
Cartridge, Impulse
Cord, Set Detonating
Connector, Inline (INERT)
Thruster, Explosive P/N 209-033 -007-3
Cartridge, Impulse, CCU-44/B
Cutter, Assembly; P/N FTL 3648-2
Refire Kit
Thruster, TCU-1B
Cutter, Cartridge Actuated P/N 303104-1
Cartridge Aircraft Fire Extinguisher
Connector, Elbow (Inert)
Connector, Tee (Inert)
Cutting Assembly Gunners Window
Cutting Assembly Pilots Window
Cutting Assembly Pilots Door
DODIC
MS59
MS58
MS51
MS53
MS57
MS56
MS55
MS54
MS52
MD73
M189
ME83
MD66
MD66
MD66
MU03
MF24
MF35
MU02
MS 62
MG51
MH92
MJ21
MS80
MS81
MS82
MS89
MS83
MS84
MS85
MS86
MS87
MS94
MS95
MS96
MS88
MS90
TM 43-0001-39
NSN 137701-186-9900
01-186-9901
01-186-9902
01-187-4477
01-263-3627
01-269-6496
01-288-0418
NOMENCLATURE
Cutting Assembly Gunners Door
Initiator, Mechanical Actuated
Cutter, Delay Propellant Actuated
DODIC
MS91
MS92
MS93
MS97
MT20
MT06
MU11
E-3 (E-4 blank)
TM 43-0001-39
APPENDIX F
CAD/PAD INDEX BY GOVERNMENT SOURCE DRAWING NUMBER
DWG NO.
FE7590-65
11740301
14195-1
1863079
2164465
2518426
2518519
2519614
2519696
2519698
2519707
2520002
5184850
39040020
5184858
5184910
813633-4
857AS300-1
857AS300-2
857AS300-3
857AS300-4
857AS400-1
857AS400-2
857AS500-1
857AS500-2
8875978
886478
9311660
897899
ARD-863-1
11-1-3043
42277E336
814033-101
816984
820810
2519614
5185107
6260906-1
6260906-2
6260906-4
6260906-5
6260906-7
6260964
6260965-2
NOMENCLATURE
Cartridge, Assembly Cargo Hook PY58
Rocket Motor, M119, M447
Cutter, Cartridge Actuated, M554
Cartridge, Impulse Mk 104 Mod 9, M291
Cartridge, Impulse Mk 19 Mod 0, M012
Cartridge, Impulse, M162
Cartridge, Aircraft Fire Extinguisher, M182
Cartridge, Aircraft Fire Extinguisher, M193
Cartridge Set, Impulse Reduced, M397
Cartridge, Impulse Guillotine, M520
Cartridge; Aircraft Fire Extinguisher, M232
Cartridge, Impulse Drogue, M507
Cartridge, Impulse, CCU-44/B, MD66
Cartridge, Aircraft Fire Extinguisher, MH92
Cartridge, Delay CCU-57/B, MF35
Thruster, Cartridge Actuated, TCU-1/B, MF24
Arming/Firing Mechanism
Cutting Assembly Pilots Door Window, MD36
Cutting Assembly Gunners Canopy Window, MD35
Cutting Assembly Gunners Canopy Window, MD34
Cutting Assembly Pilots Canopy Window, MD33
Cord, Detonating (SMDC), MD17
Cord, Detonating (SMDC), MD18
Cord, Detonating (FCDC), MD16
Cord, Detonating (FCMC), MD15
Cutter, Reef Line M21, M500
Cartridge, Delay M252, M308
Cartridge, Impulse M796, MD73
Cartridge, Aircraft Fire Extinguisher, MT20
Cartridge, Impulse M189
Cutter, Assembly MU03
Cutter, CTG Actuated MU02
Arming/Firing Mechanism
Pin Puller, Explosive Actuated (Inert)
Thruster, Explosive Actuated
CTG, Aircraft Fire Extinguisher M193
CTG, Delay CCU-89/B, MH88
Cord, Detonating (FCDC) MS90
Arming/Firing Initiator, MT06
Canopy Severance Assembly, Forward Panel, MS97
PAGE
10-7
8-3
3-5
6-11
6-3
6-5
2-3
2-5
6-13
6-19
2-7
6-17
6-27
2-9
4-3
9-3
7-3
5-23
5-21
5-19
5-17
5-13
5-15
5-11
5-9
3-3
4-7
6-25
2-11
6-7
3-9
3-7
7-5
10-5
9-7
2-5
4-5
5-91
5-93
5-97
5-89
5-95
5-107
5-105
F-1
TM 43-0001-39
DWG NO.
6260965-4
6260965-5
6260965-7
6261062-1
6261062-3
6261062-7
6261063-9
6261071
6261072
6261073
6261278
757AS400-17
841AS425-23
841AS425-35
841AS425-45
841AS425-47
841AS425-49
841AS425-51
841AS425-53
841AS425-55
841AS425-57
857AS101-1
857AS102-1
857AS103-1
857AS400-15
857AS400-21
857AS400-25
857AS400-105
857AS400-107
857AS400-109
857AS400-111
857AS400-113
857AS400-115
857AS400-117
857AS400-119
857AS400-121
857AS400-123
857AS400-125
857AS400-127
1512AS105
1512AS120
1512AS121
1660AS200
1660AS300
F-2
NOMENCLATURE
Canopy Severance Assembly, Rear Panel, MS96
Canopy Severance Assembly Forward Panel, MS94
Canopy Severance Assembly Rear Panel, MS95
Linear Explosive Assembly (LEA), MS76
Linear Explosive Assembly (LEA), Window MS79
Linear Explosive Assembly (LEA), Window MS78
Connector, Union
Connector, Tee
Connector, Elbow
Cutter, Delay, Propellant Actuated MU11
Cord, Detonating (SMDC) MS48
Connector, Cross Manifold (Inert)
Connector, In-Line (Inert)
CTG, Aircraft Fire Extinguisher, MH92
Thruster, CTG Actuated, TCU-3/A, MJ20
Cartridge, Impulse CCU-92/A, MJ21
CTG, Aircraft Fire Extinguisher, M232
CTG, Aircraft Fire Extinguisher, M182
PAGE
5-103
5-99
5-101
5-57
5-59
5-63
5-61
5-109
5-109
5-109
3-11
5-27
5-83
5-87
5-77
5-71
5-85
5-75
5-73
5-81
5-79
5-65
5-65
5-65
5-25
5-29
5-31
5-33
5-35
5-37
5-39
5-41
5-43
5-45
5-47
5-53
5-51
5-49
5-55
2-9
9-5
6-23
2-7
2-3
TM 43-0001-39
APPENDIX G
CAD/PAD INDEX BY MANUFACTURERS PART NUMBER
P/N
NOMENCLATURE
ARD 863-1
5184850
5184858
FLT 3648-2
K303104-1
P7911-2
R4181-1
MSA 96713
11-1-329
14195-1
14398-1
155468-9
1863079
816986-3
816987-103
Cartridge, Impulse
Cartridge, Impulse CCU-44/B
Cutter Assembly
Refire Kit
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Impulse
Cartridge, Delay M252
Cartridge, Assembly Cargo Hook
Cord, Detonating
Cartridge, Impulse Mk 104 Mod 0
Linear Explosive Assembly Window, (WCA)
51134-47
51134-53
51134-51
51134-45
51134-57
51134-55
51134-23
51134-49
51134-35
2519696
303104-1
30903824
42277E336
5184910
7536-1
813475-101
813475-102
813475-103
813475-104
813475-105
813475-107
813475-109
813475-111

Cartridge Set Impulse
Cutting Assembly
Cutting Assembly
DODIC
PAGE
M189
MD66
MF35
MU03
6-7
6-27
4-3
3-9
10-3
6-7
6-9
6-5
4-7
3-5
10-7
M189
M253
M162
M308
M554
PY58
M291
MS77
MS78
MS79
MS80
MS81
MS82
MS83
MS84
MS85
MS86
MS87
MS88
M397
MU02
MH92
MF24
M507
MD36
MD35
MD34
MD33
MS51
MS52
MS53
MS54
6-11
5-59
5-61
5-63
5-71
5-73
5-75
5-77
5-79
5-81
5-83
5-85
5-87
6-13
3-7
2-9
3-7
9-3
6-17
5-23
5-21
5-19
5-17
5-33
5-35
5-37
5-39
G-1
TM 43-0001-39
P/N
813475-113
813475-115
813475-117
813475-119
813475-123
813475-125
813475-15
813475-17
813475-19
813475-21
813475-25
813475-27
813592-3
813592-4
814033-101
814280-101
814280-102
8142/80-103
814280-104
816984-107
816986-1
816986-3
9311660
1044-2
FE7590-65
FE5790-95
FE7590-98
16650-1
21602-2
21738-3
23869-2
51135-5
51135-1
51135-2
51135-7
51135-4
51188-1
51207-3
51389-1
51390-1
51391-1
300051-1
LDA419700
G-2
NOMENCLATURE
Cord Assembly, Detonating (FCDC)
Cord, Detonating
Arm Fire Initiator
Cutting Assembly Pilots Door Window
Cutting Assembly Gunners Door Window
Cutting Assembly Gunners Canopy Window
Cutting Assembly Pilots Canopy Window
Rocket Motor
CTG Assembly Cargo Hook
Thruster, CTG Actuated TCU-3/A
Cartridge, Impulse, Guillotine
Connector, Union (Inert)
Connector, Elbow (Inert)
Arming/Firing Initiator
Canopy Severance Assembly, Rear Panel
Cartridge, Impulse
Cartridge, Impulse MK 19 MOD 0
DODIC
MS55
MS56
MS57
MS58
MS60
MS59
MS47
MS48
MD17
MS49
MS50
MD18
MD16
MD15
MD36
MD35
MD34
MD33
MS76
MS77
MD73
M447
PY58
MJ21
MJ20
M520
MS89
MS90
MS91
MS92
MS93
MS94
MT06
MS97
MS95
MS96
M657
MO12
PAGE
5-41
5-43
5-45
5-47
5-51
5-49
5-25
5-27
5-13
5-29
5-31
5-15
5-11
5-9
7-5
5-23
5-21
5-19
5-17
10-5
5-57
5-59
6-25
8-3
10-7
6-23
9-5
6-19
5-109
5-109
5-109
5-89
5-91
5-93
5-95
5-97
5-99
5-107
5-105
5-101
5-103
6-21
6-3
TM 43-0001-39
P/N
813475-121
813475-127
816984
820810
2518519
2519614
2519707
5185107
6261278
8875978
897899
NOMENCLATURE
Pin Puller, Explosive Actuated
Thruster, Explosive Actuated
CTG, Aircraft Fire Extinguisher
Cutter, Delay Propellant Actuated
Cartridge, Fire Extinguisher
DODIC
MS61
MS62
M182
M193
M232
MH88
MU11
M500
MT20
PAGE
5-53
5-55
10-5
9-7
2-3
2-5
2-7
4-5
3-11
3-3
2-11
G-3 (G-4 blank)
TM 43-0001-39
APPENDIX H
CAD/PAD INDEX BY NOMENCLATURE
NOMENCLATURE WITH ITEM IDENTIFIER(S)
Arm-Fire Initiator P/N 814033-101
Arming/Firing Initiator JAU-59A
Canopy Severance Assembly Forward Panel, MS94
Canopy Severance Assembly, Forward Panel, MS97
Cartridge, Aircraft Fire Extinguisher MH92
Cartridge, Aircraft Fire Extinguisher M182
Cartridge, Aircraft Fire Extinguisher MT20
Cartridge Assembly Cargo Hook PY58
Cartridge, Delay CCU-57/B, MF35
Cartridge, Delay CCU-89/B MH88
Cartridge, Delay M252, M308
Cartridge, Impulse, ARD 836-1, M189
Cartridge, Impulse, Mk 104, Mod 0 M291
Cartridge Set, Impulse, Reduce Charge Primary M397
Cartridge, Impulse Drogue, M507
Cartridge, Impulse Guillotine, M520
Cartridge, Impulse, CCU-44/B, MD66
Cartridge, Impulse M796, MD73
Cartridge, Impulse, CCU-92/A, MJ21
Cartridge, Impulse, Mk 19 Mod 0 MO12
Cord Assembly Detonating (FCDC) MD15
Cord Assembly Detonating (FCDC) MD16
Cord Assembly Detonating (SMDC) MD17
Cord Assembly Detonating (SMDC) MD18
Cord, Detonating (WCA) MD33
PAGE
7-5
5-107
5-99
5-101
5-103
5-105
2-9
2-3
2-5
2-7
2-11
10-7
4-3
4-5
4-7
6-5
6-7
6-9
6-11
6-13
6-17
6-19
6-21
6-27
6-25
6-23
6-3
5-9
5-11
5-13
5-15
5-17
5-19
5-21
5-23
5-89
5-91
5-93
5-95
5-97
5-25
5-27
5-29
H-1
TM 43-0001-39
NOMENCLATURE WITH ITEM IDENTIFIER(S)

Cutter, Assembly P/N FTL 3648-2 MU03
Cutter, Cartridge Actuated P/N 303104-1 MU02
Cutter, Cartridge Actuated M554
Cutter, Reef Line M21, M500
Linear Explosive Assembly, Window (WCA)
Tee Connector (Inert) 87AS101-2
Tee Connector (Inert) 87AS102-1
Pin Puller, Explosive Actuated, P/N 816984-107
Refire Kit
Rocket Motor M447
Thruster, Cartridge Actuated, TCU-1B, MF24
Thruster, Cartridge Actuated, TCU-3A, MJ20
Thruster, Explosive Actuated, P/N 209-033-007-3
H-2
PAGE
5-31
5-33
5-35
5-37
5-39
5-41
5-43
5-45
5-47
5-49
5-51
5-53
5-55
5-71
5-73
5-75
5-77
5-79
5-81
5-83
5-85
5-87
3-9
3-7
3-5
3-3
5-57
5-59
5-61
5-63
5-65
5-65
10-5
10-3
8-3
9-3
9-5
9-7

GORDON R. SULLIVAN
Chief of Staff
Official:
MILTON H. HAMILTON
00171
Distribution:
To be distributed in accordance with DA Form 12-34-E, block 0933, Requirements for
TM 43-0001-39.
PIN: 058915-000

TM 43-0001-39 (Cads)

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TM 43-0001-39 (Cads)

Uploaded by

Copyright:

Available Formats

TM 43-0001-39

ARMY DATA SHEETS

Approved for public release: distribution is unlimited.

HEADQUARTERS, DEPARTMENT OF THE ARMY

THE SQUIB SHALL NOT BE EXPOSED TO SOLVENTS OR

By Order of the Secretary of the Army:

By Order of the Secretary of the Army:

When applicable, insert latest change pages and dispose of

TOTAL NUMBER OF PAGES IN THIS PUBLICATION IS 231

* Zero indicates an original page.

THIS PAGE INTENTIONALLY LEFT BLANK

CARTRIDGES, AIRCRAFT FIRE EXTINGUISHER

TIME DELAY CARTRIDGES

*This manual supersedes TM 43-0001-39, 28 November 1985, including all changes.

SECTION I - EMERGENCY ESCAPE SYSTEMS FOR HELICOPTER;

REFERENCE PUBLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

CAD/PAD AIRCRAFT/HELICOPTER/EQUIPMENT CROSSREFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

AIRCRAFT/HELICOPTER/EQUIPMENT CAD/PAD CROSSREFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CAD/PAD INDEX BY DODIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

CAD/PAD INDEX BY NSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1

CAD/PAD INDEX BY GOVERNMENT SOURCE DRAWING NUMBER . . . . F-1

APPENDIX G CAD/PAD INDEX BY MANUFACTURERS PART NUMBER . . . . . . . . . . . . . . . . . . . . . G-1

(7) Reclassified OBS for all US use;

2-1 (2-2 blank)

CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER (M182)

in diameter, and with an integrally-formed convex head.

Refer to associated aircraft subsystem.

In the assembly one lead wire of each

Type ---------------------------- Hermetically-sealed metal container

CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER: (M193)

tridge, provides the means for completing the

When the fire control switch is operated,

Weight ------------------------- .75 lb

Bridgewire resistance ------- .90 ohm to

Quantity distance class ----- 1.4

TM 9-1377 -200 -20&P

CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER: (M232)

tact with the cartridge case, Both squibs fire

Refer to aircraft subsystem.

An insulated plug, attached to the firing

Vendor (CAGE code) and

Firing Temperature Limits:

Quantity distance class ----- 1.4

Bridgewire resistance is 0.025 ohms minimum

CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER CCU-90/A (MH92)

are two threaded electrical connectors, one is

Type ---------------------------- Hermetically sealed metal container

CARTRIDGE, AIRCRAFT FIRE EXTINGUISHER (MT20)

tact with the cartridge case. Both squibs fire

Refer to aircraft subsystem.

An insulated plug, attached to the firing

Type ---------------------------- Hermetically sealed metal container

Bridgewire resistance is 0.025 ohms minimum

spring and the release of the firing pin are

3-1 (3-2 blank)

CUTTER, CARTRIDGE ACTUATED: M21 (M500)

To sever a nylon reefing line which allows

Items per package ---------- 80

0.75 in. (1.905 cm)

CUTTER, CARTERIDGE ACTURATED: M22 (M504)

To sever a nylon reefing line which allows

The M22 reefing line cutter is a cartridge