23 Technical 2005 2nd

1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
International Shooting Sport Federation

Internationaler Schiess-Sportverband e.V.
Fédération Internationale de Tir Sportif
Federación Internacional de Tiro Deportivo
ISSF
TECHNICAL RULES
FOR
ALL SHOOTING DISCIPLINES
Edition 2005 (Second Printing, 09/2005)

Effective 1 January 2005
Edition 2005 (Second Printing, 01/2006) - 219 -

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
CHAPTERS
6.1.0 GENERAL
6.2.0 SAFETY
6.3.0 RANGE AND TARGET STANDARDS
6.4.0 COMPETITION OFFICIALS
6.5.0 PRE-MATCH ADMINISTRATION
6.6.0 EQUIPMENT CONTROL
6.7.0 SCORING PROCEDURES
6.8.0 PROTOCOL: AWARDS AND RECORDS
6.9.0 MEDIA RELATIONS
6.10.0 INDEX
NOTE: Where figures and tables contain specific information, these have the
same authority as the numbered rules.
- 220 - Edition 2005 (Second Printing, 01/2006)

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.1.0 GENERAL
6.1.1 Objective and Purpose of ISSF Rules
The ISSF establishes Technical Rules for the sport of shooting to
govern the conduct of shooting events recognized by the ISSF (see
ISSF General Regulations Article 3.3.1). The objective of the ISSF is
to achieve uniformity in the conduct of the shooting sport throughout
the world to promote the development of the sport. ISSF Technical
Rules are provided to help achieve this objective.
6.1.1.1 ISSF Technical Rules include rules for range construction, targets,
scoring etc. for all shooting disciplines. Discipline Rules apply
specifically to the four shooting disciplines: Rifle, Pistol, Shotgun and
Running Target.
6.1.1.2 ISSF Technical and Discipline Rules are approved by the ISSF
Administrative Council in accordance with Article 1.7.2.5 of the
Constitution of the ISSF.
6.1.1.3 ISSF Technical and Discipline Rules are subordinate to the
Constitution of the ISSF and the ISSF General Regulations.
6.1.1.4 ISSF Technical and Discipline Rules are approved to be effective
for a minimum of four years beginning on 1 January of the year
following the Olympic Games. Except in special situations, ISSF
Rules are not changed during this four year period.
6.1.2 Application of ISSF Technical and Discipline Rules
6.1.2.1 Throughout these Rules, competitions where World Records may be
established and which are approved by the ISSF in accordance with
ISSF General Regulations Article 3.2.1 are referred to as "ISSF
supervised Championships".
6.1.2.2 ISSF Rules must be applied at all ISSF Championships.
6.1.2.3 The ISSF recommends that ISSF Rules be applied at competitions
where ISSF events are in the program, even if World Records
cannot be established. Such events are referred to as “ISSF
Supervised Events”.
6.1.3 Scope of Technical Rules
Technical Rules include:
6.1.3.1 rules for the preparation and organization of ISSF Championships;
6.1.3.2 rules for planning the construction and installation of shooting ranges;
6.1.3.3 rules which apply to all shooting disciplines or more than one
shooting discipline.
6.1.4 Unless a Rule applies specifically to a men's or women's event, it must
apply uniformly to both men's and women's events.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.1.5 Organization and Conduct of ISSF Championships

6.1.5.1 An Organizing Committee must be formed in accordance with ISSF
General Regulations Article 3.4.1 and is responsible for the
preparation, administration and conduct of the shooting competitions.
Representative(s) of the ISSF may be invited as technical advisors
without voting rights.
6.1.5.2 A Chief Range Officer and appropriate Range Officers; Chief of
Referees and Referees appointed by the Organizing Committee must
be responsible for the technical aspects and conduct of the individual
shooting events.
6.1.5.3 A Chief of Classification and appropriate Classification Officers
appointed by the Organizing Committee must be responsible for the
results.
6.1.5.4 A Chief of Equipment Control and appropriate Equipment Control
Officers appointed by the Organizing Committee must be responsible
for the Equipment Control.
6.2.0 SAFETY
SAFETY IS OF PARAMOUNT IMPORTANCE.
6.2.1 ISSF Rules state only specific safety requirements which are required
by the ISSF for use in ISSF Championships. Necessary and special
safety regulations for ranges differ from country to country. For this
reason no details are stated within these Rules. The safety of a
shooting range depends to a large extent on local conditions, so
additional safety rules may be established by the Organizing
Committee. The Organizing Committee must know the principles of
range safety and take the necessary steps to apply them. The
Organizing Committee bears the responsibility for safety. Team
officials and shooters must be advised of any special regulations.
6.2.2 The safety of shooters, range officials and spectators requires
continued and careful attention to gun handling and caution in
moving about the range. Self-discipline is necessary on the part of
all. Where such self-discipline is lacking, it is the duty of range
officials to enforce discipline and the duty of shooters and team
officials to assist in such enforcement.
6.2.3 Ear Protection
Notices must be prominently displayed and hearing protection must be
available for ALL persons in the range area. All shooters and other
persons in the immediate vicinity of the firing line are urged to wear ear
plugs, ear muffs, or similar ear protection. Hearing protection in the form
of ear plugs or muffs (not plain cotton) must be provided for all range
officials whose duties require them to be near the firing line during
shooting (i.e. Register Keepers, Range Officers, Jury Members etc.).
Ear protectors incorporating any type of receiving devices are not
permitted for shooters.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.0 RANGE AND TARGET STANDARDS

6.3.1 General Target Requirements
6.3.1.1 Samples of all paper targets (5 of each type) and clay targets (20
Qualification targets and 20 powder filled Finals targets) to be used in
ISSF Championships must be submitted to the ISSF Secretary
General, to verify their conformance with ISSF specifications, at least
six (6) months prior to the start of such Championships (see ISSF
General Regulations Article 3.5.4).
6.3.1.2 The quality and dimensions of all targets will be examined again by
the Technical Delegate(s) prior to the beginning of ISSF
Championships. Only targets which are the same as the approved
samples may be used.
6.3.1.3 Target paper must be of a non-reflecting color and material so that
the black aiming area (center) is clearly visible under normal light
conditions at the appropriate distances. The target paper and scoring
rings must retain dimensional accuracy under all weather and climatic
conditions. The target paper must register shot holes without
excessive tearing or distortion.
6.3.1.4 Inner Tens must be marked, but are for the guidance of shooters and
are scored only to enable ties to be broken in accordance with these
Rules.
6.3.1.5 The dimensions of all scoring rings are measured from the outside
edges (outside diameter) of the scoring rings.
6.3.1.6 In ISSF Championships only targets with one (1) black aiming area
are permitted, except in the case of the Running Target (see Rule
6.3.2.7.2).
6.3.1.7 Targets are divided into scoring zones by scoring rings. Shots striking
in a scoring zone receive the number of points designated for that
scoring zone.
6.3.1.8 Electronic Scoring Targets
6.3.1.8.1 The Electronic Scoring Target system comprises a simulated target with
its own electronic scoring mechanism, a firing point monitor, a printer to
record the shot value and a remote display for spectators. The face of
the target is a white card without scoring rings. In the center is a hole
which is the size of the black portion of the selected target (except the
target according to the Rule 6.3.2.4 and 6.3.2.7.2.2).

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2 Paper Competition Targets

6.3.2.1 300 Meter Rifle Target
10 Ring 100 mm (±0.5 mm ) 5 Ring 600 mm (±3.0 mm )
Inner Ten = 50 mm (±0.5 mm).
Black from 5 to 10 Rings = 600 mm (±3.0 mm).
Ring Thickness: 0.5 mm - 1.0 mm.
Minimum visible size of target card: 1300 mm x 1300 mm (or
minimum 1020 mm x 1020 mm providing the background on which
the target is mounted is the same color as the target).
Scoring ring values 1 - 9 are printed in the scoring zones, in diagonal
lines at right angles to each other.
The 10 point zone is not marked with a number.
300 Meter Rifle Target

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.2 50 Meter Rifle Target

10 Ring 10.4 mm (±0.1 mm ) 5 Ring 90.4 mm (±0.5 mm )
Inner Ten = 5 mm (±0.1 mm).
Black from part of 3 to 10 rings = 112.4 mm (±0.5 mm).
Ring Thickness: 0.2 mm to 0.3 mm.
Minimum visible size of target card: 250 mm x 250 mm.
Scoring ring values 1 - 8 are printed in the scoring zones in vertical
and horizontal lines, at right angles to each other.
The 9 and 10 point zones are not marked with a number.
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
50 Meter Rifle Target

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.3 10 Meter Air Rifle Target

10 Ring 0.5 mm (±0.1 mm) 5 Ring 25.5 mm (±0.1 mm)
Inner Ten: When the 10 Ring (dot) has been shot out completely as
determined by the use of a 4.5 mm Air Rifle INWARD
scoring gauge.
Black from 4 to 9 rings = 30.5 mm (±0.1 mm).
The ten ring is a white dot = 0.5 mm (±0.1 mm).
Ring thickness: 0.1 mm to 0.2 mm.
Scoring ring values 1 - 8 are printed in the scoring zones in vertical
and horizontal lines, at right angles to each other. The 9 point zone is
not marked with a number. The 10 is a white dot.
Background cards 170 mm x 170 mm, similar in color to the target
material should be provided to improve the visibility of the target.
1
2
3
4
5
6
7
8
1 2 3 4 5 6 78 8 7 65 43 2 1
8
7
6
5
4
3
2
1
30.5mm
45.5mm
10 Meter Air Rifle Target

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.4 25 Meter Rapid Fire Pistol Target

(for the 25 m Rapid Fire Pistol event and the Rapid Fire stages of the
25 m Center Fire and 25 m Pistol events):
10 ring 100 mm (±0.4 mm) 7 ring 340 mm (±1.0 mm)
Inner Ten: 50 mm (±0.2 mm).
Black from 5 to 10 rings = 500 mm (±1.0 mm).
Minimum visible size of target card: width: 550 mm
height: 520 mm – 550 mm.
Scoring ring values 5 - 9 are printed in the scoring zones, in vertical
lines only. The 10 point zone is not marked with a number. The zone
numbers shall be approximately 5 mm high and 0.5 mm thick. White
horizontal aiming lines replace the ring values at the left and the right
side of the target center. Each of the lines is 125 mm long and 5 mm
wide.
500.0 mm
5
6
7
8
9
9
8
7
6
5
25 Meter Rapid Fire Pistol Target

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.5 25 Meter and 50 Meter Precision Pistol Target

(for the 50 m Pistol and 25 m Standard Pistol events and the
precision stage of the 25 m Center Fire and the 25 m Pistol events)
Inner ten: 25 mm (±0.2 mm).
Black from 7 to 10 rings = 200 mm (±1.0 mm).
Minimum visible size of target card: width: 550 mm
height: 520 mm-550 mm.
Scoring ring values 1 - 9 are printed in the scoring zones, in vertical
and horizontal lines, at right angles to each other. The 10 point zone
is not marked with a number. The zone numbers shall be
approximately 10 mm high, 1 mm thick and shall be read easily with
normal spotting telescopes at the appropriate distance.
1
2
3
4
5
6
7
8
9
1 2 3 4 5 6 7 8 9 9 8 7 6 5 4 3 2 1
9
8
7
6
5
4
3
2
1
200 mm
500 mm
25 Meter and 50 Meter Precision Pistol Target

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.6 10 Meter Air Pistol Target

10 ring 11.5 mm (±0.1 mm) 5 ring 91.5 mm (±0.5 mm)
Inner ten: 5.0 mm (±0.1 mm).
The scoring ring values 1 to 8 are printed in the scoring zones in
vertical and horizontal lines, at right angles to each other. The ten
and the nine zones are not marked with a number. The zone
numbers shall be not more than 2 mm high.
1
2
3
4
5
6
7
8
12 34 5678 8 7 65 4 3 2 1
8
7
6
5
4
3
2
1
59.5 mm
155.5 mm
10 Meter Air Pistol Target

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.7 Running Target

6.3.2.7.1 50 Meter Running Target
The 50 m Running Target depicts a running wild boar with scoring
rings printed on the shoulder of the animal. Targets must be printed
in one color only. The Running Target is printed to show the animal
running in left and right directions. The animal must be printed on a
rectangular-shaped target paper. Trimming the frame to the shape of
the animal is not permitted (see Figure).
Inner ten: 30 mm (±0.2 mm).
The center of the 10 ring must be 500 mm from the tip of the nose of
the boar measured on a horizontal line.
Scoring ring values 1 to 9 must be printed clearly in the appropriate
scoring zones in diagonal lines at right angles to each other.
Repair centers (C) or half targets (B) may be used. The repair
centers or half targets must be correctly placed on the full target.
B C
50 Meter Running Target

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.7.2 10 Meter Running Target

The 10 m Running Target is a single card with two scoring zones
each with rings 1 to 10 on the two sides and a single aiming mark in
the center.
Inner ten is white: 0.5 mm (±0.1 mm), gauged in the same way as
rings 3 – 10.
Recommended size of target card: 260 mm x 150 mm (minimum
260 mm x 140 mm).
The center of the 10 ring must be 70 mm (+/-0.2 mm) from the center
of the aiming mark measured on a horizontal line.
Scoring ring values 1 to 9 must be printed clearly in the appropriate
scoring zones in diagonal lines at right angles to each other.
The aiming mark is black with an outside diameter of 15.5 mm and
must include white rings of the size of the 10 (5.5 mm) and 9
(10.5 mm) rings and a white central dot (0.5 mm).
6.3.2.7.2.1 10 Meter Running Target Paper Target

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.7.2.2 10 Meter Running Target Electronic Target
70.0mm 70.0mm
15.5mm 15.5mm
30.5mm
The 30.5 mm diameter is a hole.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.2.8 Clay Targets (for shotgun events)

Diameter: 110 mm (±1 mm).
Height: 25 mm to 26 mm.
Weight: 105 g (±5 g).
The color of the targets may be all black, all white, all yellow, all
orange; or the full dome may be painted white, yellow, or orange; or
a ring may be painted around the dome in white, yellow or orange.
The color of the clay target must be specified in all programs for
ISSF Championships. The color of a target which is selected for an
ISSF Championship must be clearly visible against the background
of the range under all normal lighting conditions. The same color
targets must be used for training. Clay Targets filled with colored
powder must be used in the Finals and must meet the same
specification.
6.3.2.9 General Specifications for Clay Targets
G
D F
H
E
A-Weight 105 g ±5 g E-Base Height 11 mm ± 1 mm

B-Base Ø 110 mm ± 1 mm F-Rotating Ring Height 7 mm ± 1 mm
C-Rotating Ring Ø 95 mm – 98 mm G-Dome Height* 8 mm ± 1 mm
D-Total Height 25 mm – 26 mm H-Base & Ring Height 18 mm ± 1 mm
* "G" The actual shape of the target dome is to be engineered to provide
the best aerodynamics design and flight stability.
"Breakability" - targets must be capable of withstanding the force of
the trap to be thrown to a distance of 80 m and to be breakable easily
with normal ISSF Skeet and Trap load cartridges within legal shooting
distances.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.3 Paper Sighting Targets

Sighting targets must be marked clearly with a black diagonal stripe
in the upper right hand corner of the target. The stripe must be
clearly visible to the naked eye at the appropriate distance under
normal light conditions (except for the 25 m Rapid Fire Pistol Target).
6.3.4 Backing Targets, Backing Cards, Control Sheets
Rifle Rule 7.6.3.3
Pistol Rule 8.6.3.3, 8.6.3.4, and 8.6.3.5
Running Target Rule 10.6.3.17.5
6.3.4.1 Backing Targets for 50 m ranges
For locating cross shots if possible Backing Targets 0.5 m – 1 m
behind the targets must be used. The exact distance between the
target and the backing target should be measured and recorded. As
far as possible, this distance should be the same on all targets.
6.3.5 Range Standards
6.3.5.1 General for all Disciplines
6.3.5.1.1 The ISSF Technical Delegate(s), in accordance with ISSF General
Regulations Articles 3.4.2, 3.4.3 and 3.4.4, and in co-operation with
the Match Director and range officials appointed by the Organizing
Committee for the different disciplines, must inspect the shooting
ranges and equipment for all ISSF Championships. They may
approve small deviations from specifications in ISSF Rules which do
not conflict with the intent and spirit of ISSF Regulations and Rules,
except that no deviations in shooting distances and target
specifications are allowed. Participating countries or federations
must be notified of all approved deviations prior to the closing date
for entries in the competition.
6.3.5.1.2 New outdoor ranges should be constructed in such a way that the
sun is behind the shooter as much as possible during the
competition day.
6.3.6 Common Standards for 300 m, 50 m, 25 m and 10 m Rifle and
Pistol Ranges
6.3.6.1 Ranges must have a line of targets and a Firing Line. The firing line
must be parallel to the line of targets. The firing points are located
behind the firing line.
6.3.6.2 The range may be surrounded by walls, if necessary, for safety
reasons. Protection against the accidental exit of unaimed shots may
also be provided by transverse baffle systems between the firing line
and the line of targets.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.6.3 Protection against rain, sun and wind must be provided in

accordance with ISSF General Regulations Article 3.5.1.2. This
protection shall be such that no obvious advantage is given to any
firing point or part of the range.
6.3.6.3.1 300 m ranges should have at least 290 m open to the sky.
6.3.6.3.2 50 m ranges should have at least 45 m open to the sky.
6.3.6.3.3 25 m ranges should have at least 12.5 m open to the sky.
6.3.6.3.3.1 50 m and 25 m ranges should, whenever possible, be outdoor
ranges but may be exceptionally indoor or closed ranges if required
by legal or climatic conditions.
6.3.6.3.4 10 m ranges for ISSF championships and Olympic Games must be
installed indoors in accordance with ISSF General Regulation Article
3.5.1.
6.3.6.4 Competition area
6.3.6.4.1 Smoking on the range and in the spectator area is prohibited.
6.3.6.5 There must be sufficient space behind the firing points for the range
officials and the Jury to perform their duties.
6.3.6.5.1 Space must be provided for spectators. This area must be
separated from the area for shooters and officials by a suitable
barrier located at least 5 m behind the firing line.
6.3.6.6 The use of mobile telephones, walkie-talkies pagers or similar devices
by competitors, coaches and team officials while within the competition
area is prohibited. All mobile telephones etc. must be switched OFF.
6.3.6.6.1 Notices must be displayed to indicate to spectators that mobile phones
must be switched OFF and flash photography is prohibited.
6.3.6.7 Each range must be equipped with a large clock at each end of the
hall that can be seen clearly by shooters and officials.
6.3.6.8 Target frames or mechanisms must be marked with numbers
corresponding to their firing point number. The numbers must be
large enough to be seen easily under normal shooting conditions
with normal vision at the appropriate distance. The numbers must be
of alternating and contrasting colors and be clearly visible throughout
the competition, whether the targets are exposed or concealed.
6.3.6.9 Targets must be fixed in such a manner that they have no significant
movement even in high winds.
6.3.6.10 Any target system may be used, provided it guarantees the
necessary degree of safety, accurate control of timing, and efficient,
accurate and rapid scoring, and changing of the targets.
6.3.6.11 If Register Keepers are used, a desk and chair must be located
behind each firing point in such a way that shooters are not
disturbed.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.6.12 A communications system must be provided between the Range

Officers at the firing line and any personnel behind the targets who
are operating the target mechanisms or working in the pits.
6.3.6.13 If pits with individual markers for each target are used, there must be
a signal system between the Register Keeper and the Marker.
6.3.7 Wind Flags for 300 m and 50 m Rifle and Pistol Ranges
6.3.7.1 Private wind indicators are prohibited.
6.3.7.2 Rectangular wind flags, which indicate air movements on the range,
should be made of a cotton material weighing approximately 150
g/m². They must be placed as close to the bullets’ flight path as
possible without interfering with the bullets’ flight or the shooter's
view of the target during aiming. The color of the wind flags must be
in contrast to the background. Dual color or striped wind flags are
permitted and recommended.
6.3.7.2.1
Size of Wind Flags
Ranges Distances Size of Flag
50 m Ranges 10 m and 30 m 50 mm x 400 mm
300 m Ranges 50 m 50 mm x 400 mm
100 m and 200 m 200 mm x 750 mm
6.3.7.3 On 50 m ranges (rifle and pistol), wind flags are to be placed at
distances (see 6.3.7.2.1) from the firing line, on the imaginary lines
separating each firing point and its corresponding target from the
adjacent points and targets. Flags must be placed on the shooter's
side of any safety baffles.
6.3.7.3.1 If a 50 m range is also used as a 10 m enclosed range the 10 m wind
flags must be placed far enough down range so that they give an
indication of the wind.
6.3.7.4 On 300 m ranges, wind flags are to be placed at distances (see
6.3.7.2.1) from the firing line on the imaginary lines separating every
fourth (4th) firing point and its corresponding target from the next
point and target. Flags must be placed on the shooter's side of any
safety baffles.
6.3.8 Shooting Distances
6.3.8.1 World records will only be valid if the range meets the standards
specified in Rule 6.3.8.3.
6.3.8.2 Shooting distances must be measured from the firing line to the
target face. If pit operated targets are used the distance must be
measured to the face of the front target, which must always be the
competition target.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.8.3 Shooting distances must be as exact as possible, subject to the

following allowable variations.
300 m range +/- 1.00 m
50 m range +/- 0.20 m
25 m range +/- 0.10 m
10 m range +/- 0.05 m
50 m running target range +/- 0.20 m
10 m running target range +/- 0.05 m
6.3.8.4 In combined 50 m rifle, pistol and running target ranges, the
allowable variation can be increased to +2.50 m for running target.
The opening must be accordingly adjusted (see Rule 6.3.18.11).
6.3.8.5 The firing line must be clearly marked. The range distance must be
measured from the target line to the edge of the firing line nearest to
the shooter. The use of a board as a firing line is not permitted.
6.3.9 Height of Target Center (Center of the Ten Ring)
The center of the targets must be within the following heights when
measured from the level of the floor of the firing point:
Standard Height Variation Allowable
300 m ranges 3.00 m +/- 4.00 m
50 m ranges 0.75 m +/- 0.50 m
25 m ranges 1.40 m +/- 0.10 m
10 m ranges 1.40 m +/- 0.05 m
50 m Running Target 1.40 m +/- 0.20 m
10 m Running Target 1.40 m +/- 0.05 m
All target centers within a group of targets or range must have the
same height (±1 cm).
6.3.10 Horizontal Variations for Target Centers on 300 m, 50 m and
10 m Rifle and Pistol Range
6.3.10.1 Target centers at 300 m, 50 m, and 10 m must be oriented on the
center of the corresponding firing point. Horizontal deviations from a
center line drawn perpendicular (90 degrees) to the center of the
firing point are:
Maximum variation from center in either
direction
300 m rifle 6.00 m
50 m rifle/pistol 0.75 m
10 m rifle/pistol 0.25 m

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.11 Horizontal Variations for Firing Points on 50 m and 10 m

Running Target and 25 m Pistol Ranges
The center of the firing points must be located as follows:
6.3.11.1 for Rapid Fire ranges, according to the center of the group of five;
6.3.11.2 for Running Target ranges, according to the center of the opening;
6.3.11.3 the center of the firing point must be oriented on the center of the
corresponding target or opening. Maximum horizontal deviations
from a centerline drawn perpendicular (90 degrees) to the center of
the target or opening are:
Maximum variation in either direction
25 m range 0.75 m
50 m Running Target range 2.00 m
10 m Running Target range 0.40 m
6.3.12 General Firing Point Standards for 300 m, 50 m, 10 m Ranges
The firing point must be constructed so that it does not vibrate or
move when other persons are walking close by. From the firing line
to approximately 1.2 m rearward, the firing point must be level in all
directions. The remainder of the firing point must either be level or
may slope to the rear with a few centimeters drop.
6.3.12.1 If shooting is done from tables, the tables must be approximately
2.2 m long and 0.8 m to 1 m wide, firm, stable and removable.
Shooting tables may slope to the rear a maximum of 10 cm.
6.3.12.2 The firing point must be equipped with:
6.3.12.2.1 a bench or stand, 0.7 m - 0.8 m high;
6.3.12.2.2 a mat for shooting in the prone and kneeling positions. The front
portion of the mat must be of a compressible material not more than
50 mm thick, and approximately 50 cm x 75 cm in size and
measuring not less than 10 mm when compressed with the
measuring device used to measure the thickness of rifle clothing.
The remainder of the mat must have a maximum thickness of 50 mm
and a minimum thickness of 2 mm. The minimum overall size must
be 80 cm x 200 cm. An alternative of two mats is permitted, one thick
and one thin, but together they must not exceed the dimensions
indicated in this Rule. The use of private mats is prohibited;
6.3.12.2.3 a chair or stool for the shooter;
6.3.12.2.4 if paper targets are used, a desk and chair for the Register Keeper
and a spotting telescope must be provided;
6.3.12.2.5 a scoreboard, approximately 50 cm x 50 cm, on which the Register
Keeper can post unofficial scores for the spectators. The scoreboard
should be located so that it can easily be seen by spectators but
does not obscure their view of the shooters.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.12.2.6 when it is necessary to install dividing screens on the firing line they
must be made of transparent material on a light frame. Screens
should extend at least 50 cm forward of the firing line, and be no less
than 1.5 m long x 2.0 m high. They are to be located between every
two firing points, at the minimum;
6.3.12.2.7 if the firing point is exposed to excessive wind, additional protection
for the shooters must be provided by screens, rows of trees or other
means.
6.3.12.2.8 On new ranges wind breaks forward of the firing line are not
permitted. It is recommended that wind breaks are removed from all
ranges.
6.3.13 Firing Point Standards for 300 m Ranges
The size of the firing point must not be less than 1.6 m wide x 2.5 m
long. The width of the firing point may be reduced only if any dividing
screens are constructed so that a shooter in the prone position can
put his left leg in an adjacent firing point without disturbing that
shooter.
6.3.14 Firing Point Standards for 50 m Ranges
6.3.14.1 The size of the firing point must not be less than 1.6 m wide x 2.5 m
long if the firing point is also used for 300 m shooting.
6.3.14.2 To allow more shooters to participate in 50 m events, the width of the
firing point may be reduced to 1.25 m. Target systems used on such
ranges must be capable of changing targets without disturbing
neighboring shooters.
6.3.14.3 Light conditions for 50 m Indoor Ranges
The minimum illumination of the targets must be 1500 lux. However,
it is recommended that the minimum illumination of the targets is
3000 lux.
6.3.15 Range and Firing Point Standards for 10 m Ranges
6.3.15.1 The firing point must be a minimum of 1 m wide.
6.3.15.2 The range must be equipped according to Rule 6.3.12 with a bench
or stand, a chair or stool and, if paper targets are used, with the
equipment for the Register Keeper.
6.3.15.2.1 The nearest edge of the bench or stand must be placed 10 cm
forward of the 10 m Firing line. The use of a board as a firing line is
not permitted.
6.3.15.3 10 m ranges must be equipped with electric-mechanical target
carriers or changers, or Electronic Scoring Targets.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.15.4 Indoor 10 m ranges must have artificial illumination providing the

necessary amount of light without glare or distracting shadows on
the targets or firing points. The entire area must be evenly
illuminated with no less than 300 lux. Targets must be illuminated
evenly with no less than 1500 lux. The background area behind the
targets must be a non-reflecting, light even neutral color. If due to the
request from the media, the lighting on the firing points has to be
increased, then the light on the targets must be appropriately
increased.
6.3.15.4.1 Measuring of the target illumination (minimum 1500 lux) must be
done with the measuring device held at the level of the target and
pointed toward the firing point (A).
6.3.15.4.2 Measuring general range illumination (a minimum of 300 lux):
The measuring device must be held at the firing point (B1) and
midway between the firing point and the target line (B2) with the
device directed toward the ceiling illumination (see Figure).
6.3.15.4.3 10 m Indoor Range Light Measuring
A position of meter minimum 1500 lux

B 1-2 position of meter minimum 300 lux
c photo cell of the light meter
D edge of bench 10 cm forward of firing line
A B2
c B1
c c
Target 0.70-0.80m
D
10 m Firing Line
6.3.16 Range and Firing Point Standards for 25 m Pistol Ranges

6.3.16.1 Roofs and screens of 25 m ranges must provide the shooter with
adequate shelter from wind, rain, sun and ejected cartridge cases in
accordance with ISSF General Regulations Article 3.5.1.
6.3.16.2 The floor of the firing point must be level in all directions. It must be
of firm construction and not permit any vibration.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.16.3 The firing point must be roofed or covered at a minimum height of

2.20 m above the level of the firing point.
6.3.16.4 Firing point or shooting station dimensions must be:
Width Depth
25 m Rapid Fire Pistol 1.50 m 1.50 m
25 m Pistol and 25 m Center Fire 1.00 m 1.50 m
Pistol
25 m Standard Pistol 1.00 m 1.50 m
6.3.16.5 Firing points must be separated by transparent screens which
protect shooters from ejected cartridge cases and permit visibility of
the shooters by the officials. The screens must:
6.3.16.5.1 extend at least 0.75 m forward of the front edge of the firing line and
approximately 0.25 m to the rear;
6.3.16.5.2 be a minimum of 1.7 m high, with the top edge at least 2.0 m above
the floor of the firing point;
6.3.16.5.3 if the screen does not reach the floor of the firing point, the bottom
edge should not be more than 0.7 m above the floor of the firing line.
6.3.16.6 Each firing point must be provided with the following equipment:
6.3.16.6.1 a removable or adjustable bench or table, approximately 0.5 m x
0.6 m in size and 0.7 m to 0.8 m high;
6.3.16.6.2 a chair or stool for the shooter;
6.3.16.6.3 a desk and chair for the Register Keeper;
6.3.16.6.4 a scoreboard, approximately 0.5 m x 0.5 m on which the first
Register Keeper can post unofficial scores for the spectators. The
scoreboard should be located so that it can be seen easily by
spectators but does not obscure their view of the shooters.
6.3.16.7 Light conditions for 25 m Indoor Ranges
The minimum illumination of the targets must be 1500 lux. However,
it is recommended that the minimum illumination of the targets is
2500 lux.
6.3.17 Standards for 25 m Turning Target Installations
When Electronic Scoring Targets are not used, ranges for 25 m
events must be equipped with a target rotating or turning mechanism
which permits 90 degree (+/-10 degrees) turning of the targets on
their vertical axis. In precision stages of 25 m pistol events,
stationary target frames may be used.
6.3.17.1 The time for turning to face the shooter must not exceed 0.3
seconds.
6.3.17.2 When the targets have turned, there must be no visible vibration to
distract the shooter.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.17.3 When viewed from above, the targets must turn in a clockwise
direction to the facing position and in a counterclockwise direction to
the edge-on position (see Figure).
6.3.17.3.1 Rotation of Turning Targets
Direction for "facing" movement
Direction for "edging" movement
6.3.17.4 In 25 m events, the targets must be placed in:

6.3.17.4.1 Groups of five (5), for the Rapid Fire Pistol event;
6.3.17.4.2 groups of three (3) (1st, 3rd, and 5th) or groups of four (4) (1st, 2nd,
4th, and 5th) for the 25 m Pistol, 25 m Center Fire Pistol and 25 m
Standard Pistol events. Groups of five (5) may be used, but only
when it is necessary to save an additional relay or save range staff,
but see 6.3.11.3.
6.3.17.5 25 m ranges must be divided into sections which are composed of
two (2) groups of five (5) targets (each being one bay).
6.3.17.5.1 The sections must be separated from each other by suitable
protective walls. Protected walkways should be provided to allow
range staff to get to the target line.
6.3.17.5.2 Each Range Section should be capable of being operated centrally
but also may be operated independently.
6.3.17.6 The targets in a section must all turn simultaneously. Their
simultaneous turning within the section must be achieved by use of a
mechanism which provides efficient operation and accurate timing.
6.3.17.7 The automatic turning and timing device must ensure:
6.3.17.7.1 targets remain in the facing position for the specified period of time;
6.3.17.7.2 targets return to the edge-on position after the specified time (+0.2
seconds - 0.0 seconds).
6.3.17.8 Accurate and consistent timing of both the rotation period and the
period at rest in the facing position must be checked before and
during the competition using one of the following methods:
6.3.17.8.1 by placing the stopwatch on the edge of the target to allow the target
movements to start and stop the stop watch;
6.3.17.8.2 by using three (3) hand operated stopwatches with the middle
(median) time being accepted;

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.17.8.3 by using other systems or devices which have been approved by the
ISSF Technical Committee.
6.3.17.9 Timing must start the moment the targets begin to face and stop the
moment they begin to turn away.
6.3.17.10 If the time is less than specified or greater than 0.2 sec, the Range
Officer, acting either on his own or on instructions from a Jury
Member, must stop the shooting to allow the timing mechanism to be
regulated. In such cases, the Jury may postpone the start or restart
of shooting.
6.3.17.11 If plywood or other solid backing boards are used for the targets, the
area corresponding to the eight (8) ring zone must be cut out from
the backing board to facilitate scoring and the accurate
measurement of skid shots.
6.3.17.12 If solid backing boards are used, the center portion of the target
backing boards must be made of cardboard.
6.3.17.13 Target frames for the 25 m Rapid Fire Pistol event must be placed in
groups of five (5), all at the same height +1cm, all functioning
simultaneously and all facing one firing point which is centered on
the middle target of the group. The distance between target centers,
axis to axis, in a group of five must be 75 cm (+1cm).
6.3.17.14 Facing times for 25 m pistol events are:
6.3.17.14.1 25 m Rapid Fire Pistol 8, 6 and 4 seconds;
6.3.17.14.2 25 m Standard Pistol: 150, 20 and 10 seconds;
6.3.17.14.3 25 m Pistol and 25 m Center Fire Pistol Rapid Fire Stage:
facing for three (3) seconds for each shot, alternating with an edge-on
face away time of seven (7) seconds (+/- 1 second);
6.3.17.14.4 for all facing times a tolerance of + 0.2 seconds to - 0.0 seconds is
allowed.
6.3.17.15 Standards for 25 m Electronic Scoring Target Systems
6.3.17.15.1 When electronic scoring targets are used the timing equipment will
be set to give the nominal exposure times (see 6.3.17.14) plus 0.1
seconds (which is half the tolerance given in 6.3.17.7.2).
6.3.17.15.2 An "after-time" (the period which is to ensure that shots which would
have been valid "skid-shots" on conventional targets, are also scored
on the electronic targets) will be added at + 0.2 seconds. (Total = 0.3
seconds).
6.3.18 General Standards for Running Target Ranges
6.3.18.1 The range must be so arranged that the target runs horizontally in
both directions across an open area with a constant speed. This
area, where the target may be fired upon, is called the "opening."
The movement of the target across the opening is called a "run."

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.18.2 The protective walls on both sides of the opening must be of such a
height that no part of the target is visible until it reaches the opening.
The edges must be marked with a color differing from that of the
target.
6.3.18.3 Targets for 50 m are placed on a trolley or target carrier constructed
so that the two targets (one running to the left and one to the right)
can be alternately shown. The trolley may run on rails, cable, or a
similar system and must be moved by a driving unit which can be
regulated accurately for speed. Targets for 10 m are not changed for
left and right runs.
6.3.18.4 Ranges must be constructed to prevent any person from being
exposed to danger during shooting.
6.3.18.5 The shooting station must be arranged so that the shooter is visible
to spectators. The shooting station must be protected from rain. The
shooter should also be protected from sun and wind if this does not
prevent spectators from seeing him.
6.3.18.5.1 The shooting station must be at least 1 m wide and aligned with the
center line of fire according to 6.3.11.3. The Dry Firing position must
be located to the left of the shooting station. The shooting station
must be screened on both sides with separating partitions so that the
shooter is not disturbed by dry firing or other extraneous influences.
The separating partition between the firing point and the dry firing
point must not be longer than to allow the dry firing shooter to watch
the ready position of the competition shooter by observing the
muzzle movement of his rifle.
6.3.18.6 In front of the shooter there must be a bench or a table 0.7 m –
0.8 m high.
6.3.18.7 Behind the shooter there must be a place for the Range Officer and
at least one member of the Jury. The Register Keepers must be
located either behind or at the side of the shooting station.
6.3.18.8 Run times for the targets are:
Slow runs: 5.0 seconds, + 0.2 seconds - 0.0 seconds
Fast runs: 2.5 seconds, + 0.1 seconds - 0.0 seconds
6.3.18.9 Timing should preferably be done by using an electronic timer which
is started and stopped by switches mounted on the rail. If this
method cannot be used, timing may be done by using three (3) stop
watches operated by three different persons. The middle (median) of
the three (3) times must be counted. If the run time is found to be
less or more than that specified, range personnel or the Jury must
regulate the time to within the specified run time standards (see Rule
6.3.18.8). If the timer is built into the starting control, the timing must
be examined by the Jury and sealed.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.18.10 For ISSF approved and supervised Championships the timing must
be electronically controlled and continually displayed for inspection
by shooters and officials. Any deviation from Rule 6.3.18.8 must be
corrected immediately.
6.3.18.11 Running Target Ranges
Running Target Ranges

A visible length of target track
B opening of the wall between visible corners
C distance from the target to the visible corner of the wall
D shooting distance
Formula for determining the opening: B = A x (D – C) / D
Example (50 m): B = 10.00 m x (50.00 m - 0.20 m) / 50.00 m
C= 0,20 m B = 10.00 m x 49.80 / 50.00 = 10.00 m x 0.996
B = 9.96 m
Example (10 m): B = 2.00 m x (10.00 m - 0.15 m) / 10.00 m
C= 0,15 m B = 2.00 m x 9.85 / 10.00 = 2.00 m x 0.985
B = 1.97 m

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.18.11.1 Special Standards for 50 m Running Target Ranges

6.3.18.11.1.1 There must be a vertical wall on both sides of the opening for the
protection of operating personnel and scorers.
6.3.18.11.1.2 There must be an embankment behind the opening. In front of the
opening there must be a low wall to conceal and protect the target
carrying mechanism.
6.3.18.11.1.3 The visible length of the target track must be:
10.00 m (+ 0.05 m / - 0.00 m) as seen from the firing point. This
must be considered when measuring the opening since the distance
between the visible corner of the wall and the target increases the
distance over which the target is visible.
6.3.18.11.2 Special Standards for 10 m Running Target Ranges
6.3.18.11.2.1 If target changing and shot evaluation is done behind the target
carrier, there must be sufficient protection for operating personnel
and scorers. The target changing and evaluation must be supervised
by a member of the Jury.
6.3.18.11.2.2 Behind the opening there must be a backstop to stop pellets and
prevent ricochets. The target carrying mechanism must be
protected by a front cover plate.
6.3.18.11.2.3 The visible length of the target track must be:
2.00 m (+ 0.01 m / - 0.00 m) as seen from the firing point. This must
be considered when measuring the opening since the distance
between the visible corner of the wall and the target increases the
distance over which the target is visible.
6.3.18.11.2.4 Two shooting stations may be installed and used alternately, to
save time. In this case, the two firing points must not deviate from
the standards in Rule 6.3.11.3.
6.3.18.11.2.5 When electronic scoring targets are used the timing equipment will
be set to give the nominal exposure times (see 6.3.18.8) plus 0.1
seconds. This should ensure that the earlier appearance of the
aiming mark of the electronic scoring target is allowed for.
6.3.18.11.2.6 Target illumination minimum 1000 lux; General range illumination
minimum 300 lux (see 6.3.15.4.3 for measuring).

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.19 General Standards for Shotgun Ranges

Ranges, which are constructed in the Northern Hemisphere, should
be laid out so shooting is toward a North to North-Easterly direction.
Ranges, which are constructed in the Southern Hemisphere, should
be laid out so shooting is toward a South to South-Easterly direction.
These arrangements place the sun to the back of the shooter as
much as possible during the shooting day.
New shotgun ranges must be constructed, where it is deemed
necessary, with a shot fall zone reasonably level and free of
obstacles to permit mechanical salvage and recovery of the lead
pellets.
6.3.19.1 Standards for Trap Ranges
6.3.19.1.1 The Trap Pit
The trap pit must be constructed so that the upper surface of the
roof is on the same elevation as the surface of the shooting
stations. Interior measurements of the trap pit should be
approximately 20 m from end to end, 2 m from front to rear, and
2 m to 2.10 m from the floor to the under side of the roof. These
dimensions will allow freedom of movement for working personnel
and sufficient storage space for targets (see Figures).
6.3.19.1.2 Distances between Trap Pits
The distance between the center of machine 15 on Range A and
the center of the machine one (1) on Range B must not be less
than 35 m. For pre-existing ranges with a distance less than 35 m,
as specified above, the Jury may reduce the throwing angles of
the settings of machine 13 of Range A, and machine three (3) of
Range B, if necessary, to prevent those targets from crossing over
into the target flight path of the adjoining range and disturbing
those shooters.
6.3.19.2 The traps (clay target throwing machines)
Each trap pit must have 15 traps attached to the front wall of the
pit. The traps must be divided into five (5) groups of three (3). The
center of each group must be indicated only by a painted mark on
the top of the roof which must be positioned so that it must
indicate the point above the center trap of each group at which a
target must emerge when set to throw at zero (0) degrees. The
distance between traps within each group must be equal, from
1.00 m to 1.10 m. The distance between the center traps of
adjacent groups should be 3.00 m to 3.30 m. For existing ranges
this may be 3.00 m to 6.00 m.
6.3.19.2.1 In the case of use of machines with left-hand (clockwise) rotation
of throwing arms the distance between the left side (viewed from
behind) and the center machine in each group may be reduced to
less than the prescribed 1.00 m to 1.10 m (see also rule 6.3.21.1).

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.19.3 The traps must be installed in the pit so that the pivot point of the
throwing arm is 0.50 m (+/-0.10 m) below the top surface of the
roof of the trap pit and set back 0.50 m (+/-0.10 m) from the front
edge of the roof when the trap is set at the 2 m elevation. This is
defined as the Throwing Point. Traps may be fully automatic (self
loading and cocking), semiautomatic (hand loaded and self
cocking), or manual (hand loaded and cocked). Each trap must be
provided with a means of sealing its elevation angle, and main
spring tension after these have been inspected and approved by
the Jury. All traps must be provided with a means of making target
throwing settings on a precise setting. All traps which are hand
loaded must have two stops fixed to them. The stops are
necessary to prevent accidental or deliberate movement of the
target forward or backward on the throwing arm, thus changing the
preset directions of the target. Each trap must have the elevation
and angle sectors marked in increments of 10 degrees.
6.3.19.4 The traps must be released by an electric-manual or electric-
microphone system. The control system must be placed in such a
position that the puller can clearly see and hear the call of the
shooter. The release devices must guarantee equal distribution of
targets to each shooter in a series of 25 targets. This distribution
must be: 10 targets to the right, 10 targets to the left and 5 targets
to the center. With the correct distribution, in a series of 25
targets, each group of traps must throw two targets from the left
trap, two from the right trap and one from the center trap as the
shooters progress from station 1 to 5. After every five (5) targets
the selector index must be advanced one stop.
6.3.19.5 The five shooting stations must be arranged on a straight line at a
distance 15 m to the rear of the front edge of the trap pit. Each
station must be prominently marked with a square 1 m x 1 m which
is centered on a line perpendicular to the line of shooting stations
and extending to the middle machine in each group of three. A
sixth station must be marked about 2 m to the rear and slightly to
the left of Station 1 where shooter number 6 may take his position.
All six (6) shooting stations must have a table or bench where the
shooters may place their extra cartridges and other equipment.
The stations must be firm and level in all directions. Each station
must have at the front right and left hand corners a block of wood,
piece of carpet or rubber about 15 cm square or round upon which
the shooter may rest his gun.
6.3.19.5.1 For Trap Finals a medium intensity colored lamp must be
positioned on the left hand side behind Station 1 at a distance of
1.0 m to 1.5 m at a height of 40 cm to 50 cm. The lamp must be
controlled by a system which must be so constructed as to
indicate that for a period of 10 to 12 seconds immediately after the
shooter on Station 5 has shot at a regular target that the
microphone on Station 1 is inoperable.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.19.5.2 3 m to 4 m behind the line of shooting stations a path must be

provided for mandatory use by the shooters moving from station 5
to station 6. Shooters must not pass between the path and the
shooting stations. A wire, rope or other suitable barrier is to be
erected 7 m to 10 m behind the return walkway. No spectators are
to be allowed within this barrier. The Referee and Jury Members
are responsible for enforcing this rule. The shooting stations,
referee's stand and operator's stand should have adequate
protection from sun and rain.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.19.5.3 Trap Range

Maximum Angle of Target
90°
1.0 to 1.1m
2.3m 3 to 3.3m
Between Traps 45° 45° 0.5m (+0.1m)
Set back
2m of pivot point
Minimum of throwing
Inside arm
Dimension Station No. 1 Station No. 2 Station No. 3 Station No. 4 Station No. 5
Clay Target Pit Down
Note:
Inside Walls
Direction see Note:
shown only
Rule 6.3.19 Entrance may be on either end,
for Clarity
as shown, or in front, ( same
15m side as traps) on either end.
If located in front, there must
be at least 6m from end wall
(inside) to Centerline of center
trap of adjacent group .
Complete underground wiring

prior to pouring concrete .
Firing Station
No. 1 No. 2 No. 3 No. 4 No. 5

1.5m
1.0m
No. 6 Referee and

1.5m
Operator stand
3.0m
Return Walkway

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.20 Standards for Automatic Trap Ranges

6.3.20.1 The Trap Pit (see Rule 6.3.19.1.1)
6.3.20.2 The Shooting Stations
The shooting stations will be arranged on line measured and drawn at
15 meters to the rear of the trap house, measured from the center of the
front edge of the trap house roof. Station 3 will be centered on a line
drawn through the center of the trap house and perpendicular to the
roof front edge. Stations 1 and 2, and 4 and 5, will be located on the
line, centered on points measured 3.0 – 3.3 and 6.0 – 6.6 meters to the
left and right of the centerline, respectively (see Figure).
6.3.20.3 The Trap (clay target throwing machine)
The pit shall be equipped with a single, multi-oscillating (vertical and
horizontal directions) mechanically, or electrically, operated trap. It may
be either manually or automatically loaded. Targets may be released
manually, electrically, or microphone-electrically. The trap will be so
constructed and mounted that it will throw at random, and at
continuously changing angles and elevations, an unbroken target within
the vertical limits of 1.5 m to 3.5 m (+/- 0.1 m) and the horizontal limits
of 30° minimum to 45° maximum (see Figure 9.19.1).
6.3.20.4 Trap, Double Trap and Automatic Trap pit section
15m
Shooting
Station
0.10m
0.50m (+ 0.10m)
0.50m Set-back of pivot
point of throwing
arm
2.0m
2.10m
0.95m
2.0m

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.20.5 Automatic Trap Range
0.5m (+0.1m)
Set back
of pivot point
2Minimum of throwing
Inside arm
Dimension
AutomaticTrap Pit Down
4-5m
Note:
InsideWalls Directions see
shown only Rule 6.3.19
for Clarity
15m
Firing Station 3.0-3.3m
No. 1 No. 2 No. 3 No. 4 No. 5

1.5m
1.0m
No. 6 1.5m Referee

d
Operator
3.0m d
ReturnWalkway
6.3.21 Standards for Double Trap Ranges

6.3.21.1 The Trap Pit
Trap ranges are most commonly adapted to Double Trap competition
by using the center group of traps, numbers 7, 8 and 9, directly in
front of Station 3. See Rules 6.3.19.1.1 and 6.3.19.1.2 and Figures.
6.3.21.2 Distances between Trap Pits
6.3.21.2.1 See Rule 6.3.19.1.2 when Trap pits are used.
6.3.21.2.2 When separate Double Trap pits are constructed, see Figures
6.3.21.2.9, the distance from the center machine on one field to the
center machine on the adjoining field should not be less than 35 m.
(The angles of targets in Double Trap (see Figure) are not so severe
as Trap therefore do not need reductions.)
6.3.21.2.3 The Traps (target throwing machine)
Each Double Trap pit must have three (3) Traps attached to the front
wall of the pit. The center trap of the group must be indicated only by
a painted mark on the top side of the pit roof. The distance between
traps within the group must be equal, from 1.00 m to 1.10 m (see
Rule 6.3.19.2). Traps number 1 and number 3 should be a minimum
of 1.50 m from the end walls.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.21.2.4 The traps must be installed in the pit so that the pivot point of the
throwing arm is 0.50 m (+/-0.10 m) below the top surface of the roof
of the trap house and set back 0.50 m (+/-0.10 m) from the front edge
of the roof when the trap is set at the 2 m elevation (see Figures).
Traps may be fully automatic (self loading and cocking),
semiautomatic (hand loaded and self cocking), or manual (hand
loaded and cocked). Each trap must be provided with a means of
sealing its elevation, angle, and main spring tension after these have
been inspected and approved by the Jury. All traps must be provided
with a means of allowing target throwing on a precise setting. All
traps which are hand loaded must have two stops fixed to them. The
stops are necessary to prevent accidental or deliberate movement of
the target forward or backward on the throwing arm, thus changing
the preset directions of the target. Each trap must have the elevation
and angle sectors marked in increments of 10 degrees.
6.3.21.2.5 The traps must be released by an electric-manual or electric-
microphone system fitted with a timer device. The control system
must be placed in such a position that the puller can clearly see and
hear the call of the shooter. For all ISSF championships an automatic
timer must be used. The timer device must be set to release the
targets within the period varying randomly from zero (0) to one (1)
second after the shooter’s call. The system must guarantee the
simultaneous release of the two (2) targets from the predetermined
traps. Where an electric-manual system is used, the release device
must be designed so that only one (1) button or switch can be used
to release the targets.
6.3.21.2.6 The five (5) shooting stations must be arranged on a straight line at a
distance of 15 m to the rear and parallel to the front edge of the trap
pit. Each station must be prominently marked with a square 1 m x 1
m. Station 3 must be centered on the middle trap in the group.
Station 2 is 3 m - 3.30 m to the left of Station 3 and Station 1 is
equidistant to the left of Station 2. Likewise Station 4 is 3 m - 3.30 m
to the right of Station 3 and Station 5 equally 3 m - 3.30 m to the right
of Station 4 (see Figure, Separate Double Trap Range). A sixth
Station must also be marked about 2 m to the rear and slightly to the
left of station 1 where shooter number 6 may take his position at the
start of the competition. All six of the shooting stations must be
furnished with a table or bench where the shooters may place their
extra cartridges and equipment. The stations must be firm and level
in all directions and must be at the same elevation as the front edge
of the roof of the trap pit. Each station (six) must also have a block of
wood, piece of carpet or thick rubber sheet about 15 cm square or
round upon which a shooter may rest his gun.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.21.2.7 For Double Trap Finals a medium intensity colored lamp must be
positioned on the left hand side behind Station 1 at a distance of
1.0 m to 1.5 m at a height of 40 cm to 50 cm. The lamp must be
controlled by a system which must be so constructed as to indicate
that for a period of 10 to 12 seconds immediately after the shooter
on Station 5 has shot at a regular target(s) that the microphone on
Station 1 is inoperable.
6.3.21.2.8 3 m to 4 m behind the line of shooting stations a path must be
provided for mandatory use by the shooters moving from station 5
to station 6. Shooters must not pass between the path and the
shooting stations. A wire, rope or other suitable barrier is to be
erected 7 m to 10 m behind the return walkway. No spectators are
to be allowed within this barrier. The Referee and Jury Members
are responsible for enforcing this rule. The shooting stations,
referee's stand and operator's stand should have adequate
protection from sun and rain.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.21.2.9 Separate Double Trap Range - 3 Machines
1.0 to 1.1m
BetweenTraps 0.5m +0.1m)
(
Set back
2m of pivotpoint
Minimum of throwing
Inside arm
Dimension 1 2 3
ClayTarget Pit Down
4-5m
Note:
InsideWalls Directions see
shown only Rule6.3.19
for Clarity
15m
FiringStation 3.0-3.3m
No. 1 No. 2 No. 3 No. 4 No. 5
1.5m
1.0m
No. 6 1.5m Referee and
Operator stand
3.0m
ReturnWalkway

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.22 Standards for Skeet Ranges

6.3.22.1 A skeet field consists of two houses (high house and low house) and
eight shooting stations. Stations 1 through 7 are arranged on a
segment of a circle with a 19.2 m radius and a base chord of 36.8 m
(with a tolerance of +/- 0.1 m) which is 5.5 m from the center point of
the circle which is marked by a stake.
6.3.22.1.1 The center of the circle is marked by a stake which also marks the
base of the target crossing point.
6.3.22.1.2 Station 1 is located at the left end of the base chord and station 7 at
the right end when standing anywhere on the segment of the circle
and facing the center stake. Stations 2 through 6 are located on the
segment of the circle at points equidistant from each other (the exact
distance between the center of the front of the stations 1 and 2, 2
and 3, etc., is 8.13 m on chord). Station 8 is located at the center of
the base chord (see Figure).
6.3.22.2 Shooting stations 1 through 7 are 0.9 m +/-0.05 m x 0.9 m +/-0.05 m
square, with two sides parallel to a radius of the circle drawn through
the station marker (center of the station). Shooting station 8 is
rectangular, 0.9 m +/-0.05 m wide by 1.85 m +/-0.05 m long, with its
long sides parallel to the base chord. The location of each shooting
station must be accurately indicated. The markers for shooting
stations 1 through 7 are on the center of the side nearest the target
crossing point. The marker for shooting station 8 is on the center
point of the base chord. All 8 shooting stations must be on the same
level, within +/-0.05 m difference in elevation.
6.3.22.3 Target Distances, Angles and Elevations
6.3.22.3.1 Each trap house must contain a trap (clay target throwing machine)
in a fixed position.
6.3.22.3.2 Targets thrown from the high house must emerge at a point 0.9 m
+/-0.05 m behind the station marker 1 (measured along the extended
base chord) and 3.05 m +/-0.05 m above the level of station 1. The
target thrown from the low house must emerge at a point 0.9 m +/-
0.05 m behind station marker 7 (measured along the extended base
chord) (moved 0.75 m +/-0.05 m to the exterior of the base chord)
and 1.05 m +/-0.05 m above the level of station 7.
6.3.22.3.3 Targets properly released must pass through a circle 0.9 m – 0.95 m
in diameter, located 4.60 m +/-0.05 m above the target crossing
point.
6.3.22.3.4 In calm weather conditions targets must carry a minimum of 65 m
and a maximum of 67 m as measured from the face of the house
behind stations 1 and 7. If the correct distance cannot be verified by
measurement, the Jury will decide the trajectory of the targets.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.22.4 The shooting boundaries of stations 1 to 7 are 40.3 m +/-0.1 m from

the face of each house. For station 8 the shooting boundary is
determined by the crossing point between a straight line running
from station 4 to station 8 and the target crossing point. Suitable
markers must be placed on the target flight path, at points 40.3 m +/-
0.1 m from both the high house and the low house, to indicate the
shooting boundaries. Similar markers must be placed at 65 m and
67 m to indicate the distance of a regular target.
6.3.22.5 A safety shield must be installed at the opening of each trap house
so that the trap operator is not visible to a shooter on any station.
This precaution is mandatory as a safety measure to protect the
operator from possible injury from direct or ricocheting shot, and the
shooters from broken targets emerging from the opening of the trap-
house. A wire, rope or other suitable barrier is to be erected 7 m to
10 m behind Station 4 and parallel to the base chord. No spectators
are allowed within this barrier. The Referee and Jury Members are
responsible for enforcing this Rule.
6.3.22.6 The traps must be released by an electric-manual or electric-
microphone system (see note below) with a timer device which must
be installed so as to allow the operator to see and hear the
competitors. For all ISSF Championships the use of a timer is
mandatory. This must provide for the release of the targets within an
indefinite period of time, varying from instant release up to a
maximum of three (3) seconds after the shooter has called for his
target. The release device must be designed so that only one (1)
button (or switch) can be used to release double targets.
Note: If an electro-microphone system is to be used, it must be so
constructed as to randomly insert a delay varying from 0.2 to 3.0
seconds.
6.3.22.7 A colored lamp must be fitted to the outside of both high and low
houses. The lamps must light immediately when the Puller presses
the release and extinguish when the target(s) are thrown. The lamps
must be clearly visible to the referee. The lamp must be installed on
the side of the skeet house which faces the spectator area at a
height of 2.2 m – 2.8 m on the high house and 1.6 m – 2.0 m on the
low house.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.22.8 Skeet Range Layout

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.3.22.9 Skeet Range View

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.4.0 COMPETITION OFFICIALS

6.4.1 At ISSF Championships, juries must be formed in accordance with
ISSF General Regulations Articles 3.4.5 to 3.4.7 to advise, assist
and supervise the competition officials appointed by the Organizing
Committee.
6.4.1.1 The Range Officers are responsible for the actual conduct of the
competition while the Jury acts in an advisory and supervisory
capacity. They must cooperate fully together. The Range Officers
and Jury are responsible to the Organizing Committee and to the
ISSF, respectively, for the conduct of the competitions in
accordance with ISSF Regulations and Rules.
6.4.1.2 All Range Officers and Members of the Jury must be familiar with
the ISSF Rules and they must ensure that these Rules are enforced
in a fair and equitable manner during the competitions.
6.4.1.3 Members of the Jury have the right to make individual decisions
during the competitions, but should confer with other Jury Members
and Range Officers when any doubt exists. If a Team Official or
Shooter does not agree with a decision of an individual Jury
Member, a decision of the majority of the Jury may be sought by
making a written protest.
6.4.1.4 When a written protest is made it must be decided by a majority of
the Jury. When a team official or shooter does not agree with such
a Jury decision, he may appeal that decision to the Jury of Appeal.
Decisions of the Jury of Appeal are final in all ISSF Championships.
Decisions by the Classification Jury on the value or the number of
shots on a target are final and may not be appealed.
6.4.2 Duties and Functions of the Jury
6.4.2.1 Before the beginning of the competition, each discipline Jury must
examine the shooting ranges and check the organizational
arrangements and organization of operating personnel, etc., to
ensure that they conform to ISSF Rules. This is independent of an
earlier check by the Technical Delegate.
6.4.2.2 When electronic scoring targets are used, targets must be checked
for functioning and accuracy by the Technical Delegate (this may be
delegated by the TD to the appropriate Jury).
6.4.2.3 The Juries must supervise the examination of the guns, equipment,
and accessories, and continuously observe the shooting positions of
the shooters.
6.4.2.4 The Juries have the right to examine the guns, equipment,
positions, etc., of the shooters at any time, even during the
competitions. During the competition, their approach should not be
made while the shooter is firing a shot (or series of shots in timed
fire events). Immediate action must, however be taken when a
matter of safety is involved.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.4.2.5 The Jury must supervise target distribution, the allocation of firing
points and shooting time schedules.
6.4.2.6 The Jury must deal with any protest(s) which have been submitted
to the Organizing Committee in accordance with the ISSF
Regulations and Rules. After consultation with the Range Officers
and others directly concerned the Jury shall rule on the protest(s).
6.4.2.7 A majority of the Jury must always be present on the range during a
competition so that, if necessary, a Jury meeting can be called and
decisions made immediately. The Chairman of the Jury must ensure
the presence of sufficient members of the Jury at all times including
during Official and Pre-Event Training.
6.4.3 The Jury must decide all cases which are not provided for in the
ISSF Regulations and Rules. Such decisions must be made within
the spirit and intent of the ISSF Regulations and Rules. Any such
decisions must be put into writing and sent to the ISSF Secretariat
so that necessary rules may be clarified or changed.
6.4.4 Shooters and Team Officials must not be members of a Jury. Jury
Members must not advise or assist shooters beyond the scope of
the ISSF Rules at any time during the competition.
6.5.0 PRE-MATCH ADMINISTRATION
(Firing Point Allocation and Elimination Matches)
6.5.1 National Federations must submit final entries with the names of the
shooters for individual and/or team events to the Organizing
Committee at least 30 days in advance of the championships. The
first and second substitute must be registered with the organizing
Committee at least two (2) days before the start of the event (see
ISSF General Regulations Article 3.7.6.3).
6.5.2 Shooters and Team Officials must be informed of the exact shooting
time schedules and allocated firing points no later than 18:00 hours
on the day preceding the competition. This rule also applies for
training (for shotgun see 9.7.1.1).
6.5.3 If it should become necessary to change the shooting schedule, the
shooters must be informed no later than 18:00 hours on the day
preceding the competition or the training. This rule also applies in
case of Elimination stages (for shotgun see 9.7.1.2 and 9.7.1.3).
6.5.4 If a shooter has fired his first sighting shot in the competition and
must withdraw, he may not be replaced. This rule also applies for
competitions composed of several parts or carried out over several
days.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.5.5 Basic principles for firing point allocation

6.5.5.1 Individual shooters and teams (nations) should be able to shoot
under conditions that are as near to equal as possible.
6.5.5.1.1 Shooters from the same nation should not be allocated adjacent firing
position.
6.5.5.1.2 Shooters from the same nation should be split as equitably as possible
between relays.
6.5.5.2 The random allocation of shooters to firing points and relays may be
done either by the drawing of the lots or with a computer program
suited to this purpose, under supervision of the Technical
Delegate(s).
6.5.5.2.1 If more than one relay is used in team competitions, then team
members must be distributed equitably between the relays.
6.5.6 In the Shotgun events the random selection of ranges and the
division of the rounds may be done either by the drawing of lots or
with a computer program suited for the purpose under the
supervision of the Technical Delegate(s) (see also 9.7.4.3 and
9.6.5).
6.5.7 Training
6.5.7.1 Official Training
Official Training must be provided the day following the official
arrival day and before the beginning of the competitions (see Article
3.7.10 of the ISSF General Regulations and Annex “C” for ISSF
World Cups).
6.5.7.2 Pre-Event Training
For Rifle, Pistol and Running Target the range must be available; a
minimum of one (1) hour for a short training period on the day
before the event. This is in addition to the official training day(s) in
the program (for the Shotgun see 9.6.2.1).
6.5.7.3 Unofficial Training
In addition to the Official Training provided for in the General
Regulations before the beginning of the competitions (see Article
3.7.10 of the ISSF General Regulations), shooters should be given
the opportunity to train during the competitions, insofar as this is
possible from the organizational point of view.
6.5.7.4 A specially designated function firing range, without targets, must
be provided for shooters to test guns during competition days.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.6.0 EQUIPMENT CONTROL

See also Guidelines for Uniform Equipment Control for Rifle, Pistol
and Running Target (available from the ISSF Headquarters).
6.6.1 The Organizing Committee must provide a complete set of gauges
and instruments for equipment control before and during ISSF
Championships.
6.6.2 Prior to the competition each shooter's gun and other equipment
must be examined by the Equipment Control Section to ensure that
it conforms to ISSF Rules. The shooter is responsible for presenting
all guns and equipment, including any questionable equipment
and/or accessories for official inspection and approval before use.
6.6.3 The Organizing Committee must inform team officials and shooters,
in sufficient time prior to the competition, where and when they may
have their equipment inspected.
6.6.4 The Equipment Control Section will be assisted and supervised by a
Jury Member(s).
6.6.5 The Equipment Control Section must register the name of the
shooter, the make (manufacturer), serial number, and caliber of
each gun approved on an Equipment Control Sheet.
6.6.6 All approved equipment must be marked with a seal or sticker and
the approval must also be recorded on the Equipment Control
Sheet.
6.6.7 After equipment has been approved, it must not be altered at any
time prior to or during the competition in any way that would conflict
with the ISSF Rules.
6.6.8 If there are any doubts regarding an alteration, the equipment must
be returned to Equipment Control for reinspection and approval.
6.6.9 Approval of any equipment is valid only for the competition for which
the inspection was made.
6.7.0 SCORING PROCEDURES
6.7.1 The Classification Office must publish Preliminary scores on the
Main Scoreboard as soon as possible after each relay and stage
and completion of each event.
6.7.2 The Official Results Booklet lists must contain the following:
6.7.2.1 a list of contents;
6.7.2.2 a Results Certification Page (to be signed by the Technical
Delegate(s) and all Jury Chairmen);
6.7.2.3 a list of Competition Officials;
6.7.2.4 a list of Entries by Nations and events;
6.7.2.5 the Competition Schedule;
6.7.2.6 a list of Medalists by name;
Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.7.2.7 a list of Medals by Nations by number;

6.7.2.8 a list of New and Equaled Records;
6.7.2.9 the Final Results in the standard ISSF order of events (men – rifle
10 m, 50 m and 300 m, pistol 10 m, 50 m and 25 m, shotgun trap,
double trap and skeet, running target 10 m and 50 m; women –
same order; junior men – same order; junior female – same order).
6.7.2.9.1 These lists must contain the full names as used in the ISSF ID
Numbers (family name (capital letters), full first name (first letter
capital-rest small letters)), Bib numbers and the Nation (official IOC
code) of each shooter.
6.7.2.9.2 The following abbreviations must be used in the result list when
appropriate:
DNF Did not Finish
DNS Did not Start
DSQ Disqualified
NOE Not Officially Entered
WR New World Record
EWR Equaled World Record
FWR New Final World Record
EFWR Equaled Final World Record
WRJ New World Record Junior
EWRJ Equaled World Record Junior
OR New Olympic Record
EOR Equaled Olympic Record
FOR New Final Olympic Record
EFOR Equaled Final Olympic Record
6.7.3 One (1) copy of the official result lists of each event must be sent to
the ISSF Secretariat via Fax or Email immediately after it has been
verified, but not later than the end of the competition day.
6.7.4 Three (3) copies of the complete official result lists must be sent to
the ISSF Secretariat immediately upon conclusion, at the latest
within three (3) days after the completion of the events.
6.7.5 Classification Office
The Organizing Committee must establish an office for testing,
stamping, numbering and preparing targets before the competitions,
for scoring and controlling targets during competitions and for
recording and producing results lists after competitions. The office
must be under the supervision of the Chief Classification Officer,
with the necessary Assistants.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.7.6 The Classification Jury must supervise the scoring and all work
done in the Classification Office and on the 25 m target line. It
directs how any questionable shots shall be scored, determines
their value, and resolves any questions or scoring protests. The
official final results list must be verified and signed by a Member of
the Classification Jury to confirm its accuracy.
6.7.6.1 When Electronic Scoring Targets are used many of the functions
are undertaken by these machines, however the Classification Jury
must resolve any queries/protests relating to scoring and they must
also conduct the independent check of the top results (6.7.13).
6.7.7 At ISSF Championships the targets of the following events must be
scored in the Classification Office:
6.7.7.1 all Rifle events at 10 m, 50 m and 300 m (paper targets only);
6.7.7.2 all Pistol events at 10 m and 50 m (paper targets only);
6.7.7.3 all Running Target events at 10 m and 50 m (paper targets only);
6.7.7.4 all results in those events or stages which are scored at the
shooting range are considered preliminary results.
6.7.8 All targets for events to be scored in the Classification Office must
be transported in a locked container from the target line to the
Classification Office under suitable security.
6.7.9 Competition targets for events which are scored in the Classification
Office must be numbered and must agree with the scorecard. The
Classification Office is responsible for the correct numbering of the
targets and must verify the targets prior to every event before they
are released to the Chief Range Officer or other range officials.
6.7.10 The Chief Range Officer and the Chief of the Classification Office
are responsible for the quick delivery of targets to the Classification
Office for scoring immediately after they have been fired, so that
there will be no delay in the completion of the results list.
6.7.11 In the Classification Office, the following scoring procedures must
be checked by a second official:
6.7.11.1 determining the value of individual shot;
6.7.11.2 adding shot values or points to be deducted;
6.7.11.3 entries on the main scoreboard;
6.7.11.4 adding the individual series and overall total.
6.7.12 Each official must certify his or her work by initialing the target,
score card or results list.
6.7.13 Independent of the results determination, the Classification Jury
must examine the 10 best individual and the 3 best team results
prior to the publication of the final results list.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.7.14 Value of Shots

All bullet holes are scored according to the highest value of the
target scoring zone or ring that is touched by that bullet hole. If any
part of a scoring ring (demarcation line between the scoring zones)
is touched by the bullet, the shot must be scored the higher value of
the two scoring zones. Such a hit is determined by whether the
bullet hole or a plug gauge inserted in the hole touches any part of
the outside edge of the scoring ring.
6.7.14.1 An exception to this Rule is the scoring of inner tens on the air rifle
target (see 6.3.2.3).
6.7.14.2 Shots in dispute must be determined as to value by means of a
gauge or other device which has been approved by the ISSF
Technical Delegate for accuracy. Gauges must always be inserted
into the shot hole with the target in the horizontal position.
6.7.14.3 When the accurate use of the plug gauge is made difficult by the
close proximity of another bullet hole, the shot value must be
determined by means of an engraved gauge of some flat,
transparent material, to aid in reconstructing the position of a
scoring ring or number of bullet holes which may overlap.
6.7.14.4 If two scoring officials do not agree on the value of a shot, a
decision from the Jury must be requested immediately.
6.7.14.5 The plug gauge may be inserted only once in any bullet hole and
only by a Jury Member. For this reason the use of a gauge must be
marked on the target by the scoring officials, together with their
initials, and showing the result.
6.7.14.6 Hits outside the scoring rings of the shooter's own target are scored
as misses.
6.7.14.7 Decisions by the Classification Jury on value or number of shots on
a target are final and may not be appealed.
6.7.15 Gauges for paper targets
For scoring doubtful shot holes, plug gauges of the following
dimensions must be used:
6.7.15.1 25 m Center Fire Pistol
Measuring edge diameter: 9.65 mm (+ 0.05/-0.00 mm)
Edge thickness: 0.50 mm approximately
Spindle diameter: According to caliber being scored
Spindle length: 10 mm to 15 mm
To be used for: Center Fire Pistol Events

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.7.15.2 300 m Rifle

Measuring edge diameter: 8.00 mm (+ 0.05/- 0.00 mm)
Spindle diameter: According to caliber being scored
To be used for: 300 m Rifle events
6.7.15.3 Smallbore Rifle and Pistol 5.6 mm (.22")
Spindle diameter: 5.00 mm - 5.20 mm
To be used for: All events using 5.6 mm ammunition
6.7.15.4 4.5 mm INWARD Gauges
Spindle diameter: Measuring edge diameter minus
0.02 mm (4.48 mm)
To be used for: Measuring Inner Tens in 10 m Rifle and
Pistol Events. Measuring the 1 and 2
rings of Air Rifle and 10 m Running
Targets. Measuring the 1 Ring of Air
Pistol Targets.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.7.15.5 4.5 mm OUTWARD Gauge for 10 m Air Rifle and 10 m Running

Target
Spindle diameter: 4.60 mm (+0.05 mm)
To be used for: 10 m Air Rifle and 10 m Running
Target, rings 3 to 10. Also the
Running Target Inner Ten.
6.7.15.5.1 Air Rifle OUTWARD scoring gauge
Sizes in mm
15-20
~0.5
Spindle ~80° 10-15
4.60
Measuring
diameter 5.50
6.7.15.5.2 Use of the Air Rifle OUTWARD scoring gauge

A B
5 5
6 6
7 7
8 8
5.5 5.5
5 6 7 8 8 7 6 5 fs
5 6 7 8 6 5
8 8
7 7
6 6
5 5
Bullethole
The "A" illustration depicts a doubtful shot hole. The outward

scoring gauge shows the outside edge of the flange lying within the
7 ring; therefore the shot is scored a 9.
The "B" illustration depicts a doubtful shot hole. The outward
scoring gauge shows the outside edge of the flange lying over the 7
ring and into the 6 zone; therefore the shot is an 8.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.7.15.6 4.5 mm OUTWARD Gauge for 10 m Air Pistol

Spindle diameter: 4.60 mm (+0.05 mm)
To be used for: 10 m Air Pistol, rings 2 to 10.
6.7.15.6.1 Air Pistol OUTWARD scoring gauge
15-20
~0.5
Spindle ~80° 10-15
4.60
Measuring
diameter
11.50
6.7.15.6.2 Use of the Air Pistol OUTWARD scoring gauge

8
9
B
8 8
11.5 A
9
Bullethole
8
fs
The "A" illustration depicts a doubtful shot hole with the outward
scoring gauge in place. The outside edge of the flange is within the
9 ring; therefore the shot is scored a 10.
The "B" illustration depicts a doubtful shot hole with the outward
scoring gauge in place. The outside edge of the flange is lying over
the 9 ring line and into the 8 zone; therefore the shot is scored a 9.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.7.15.7 Skid Gauge

The Skid Gauge is a flat, transparent plastic plate with two parallel
lines engraved on one side.
6.7.15.7.1 For 25 m Center Fire Pistol (9.65 mm) the lines are 11.00 mm
(+0.05 mm-0.00 mm) apart measured between the inside edges.
6.7.15.7.2 For Small Bore Competitions (5.6 mm) the lines are 7.00 mm
(+0.05 mm - 0.00 mm) apart measured between the inside edges.
(To be used for 25 m 5.6 mm pistol events).
6.7.15.8 All gauges and instruments that are used at ISSF Championships
must be examined and approved by the ISSF Technical Delegate
prior to the competition.
6.7.15.9 Skid Shots (ricochets) in Running Target events are to be scored as
misses.
6.7.16 Results must be recorded:
6.7.16.1 by the Register Keeper, on a score card which must have spaces
for the name, nation, bib (start) number of the shooter, number of
the relay, range and firing point, the sighting shots, and competition
scores. There must be room for entering other necessary details
such as malfunctions, extensions of time, warnings, penalties,
irregularities, etc;
6.7.16.2 by the Classification Office in the master register and on the main
scoreboard;
6.7.16.3 for the benefit of the spectators, the score must be marked by the
Register Keeper on a small scoreboard located behind the shooter.
6.8.0 PROTOCOL: AWARDS AND RECORDS
6.8.1 World Records and Final World Records may be established in
Olympic Games, World Championships, World Cups, Continental
Championships and Continental Games which had been conducted
according to the ISSF General Regulations Article 3.10.
6.8.2 World Records in individual events may be established in
Elimination as well as in Qualification and Finals competitions.
6.8.2.1 If exceptionally the Finals are conducted in indoor ranges at 25 m
and 50 m Final World Records may be established.
6.8.3 An accurate report on newly established World or Olympic Records
must be prepared by the ISSF Technical Delegate(s) at the
championship. The report must confirm that the Regulations and
Rules of the ISSF and the competition program were followed (see
Article 3.12.3.6 Annex “R” to ISSF General Regulations).
6.8.4 World Records for women may be established in programmed
women's events. World records for men may be established in
programmed men's events.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.8.5 Junior World Records, male and female, may be established in

programmed men's or women's events or special Junior events in
ISSF supervised Championships. These Junior events will be
recognized if a minimum of 10 shooters participate in the individual
category and three (3) teams participate in the team category (see
Article 3.10.2 of the ISSF General Regulations).
6.8.6 World Records will be recognized in individual events if a minimum
of 15 shooters participate, and in team events if a minimum of five
(5) teams participate (see ISSF General Regulations Article 3.10.3).
6.8.7 Titles and Medals
6.8.7.1 In the Olympic Games all titles and medals are awarded for
individual competition only in accordance with IOC Rules. The
Olympic shooting events are listed in the ISSF General Regulations
Article 3.3.2.
6.8.7.2 In World Championships, the ISSF awards titles and medals for the
programmed events based on the final official results in accordance
with ISSF General Regulations Article 3.9.2. The World
Championship shooting events are listed in the ISSF General
Regulations Article 3.3.3.
6.8.7.3 World Championship individual titles and medals will only be
awarded if a minimum of 15 shooters participate in men's and
women's events and 10 shooters in junior's events. World
Championship Team titles and medals will only be awarded if a
minimum of five (5) teams participate in men's and women's events
and three (3) teams in junior's events. If these minimums are not
reached, the event will be declared an "International Championship"
of the nation which organized the competitions.
6.8.7.4 Medals and awards must be given immediately after the Finals or
after the protest time with sufficient time for the athletes to change
into suitable clothing (not shooting clothing).
6.9.0 MEDIA RELATIONS
6.9.1 Suitable facilities, assistance and co-operation must be provided for
the press, radio, and television personnel, to ensure publicity.
During competitions, however, the competitors must not be
disturbed by photography and/or interviews.
6.9.2 The Classification Office must publish the correct Final Results lists
as soon as possible after completion of each event. These must
contain the full family name, full first name (without abbreviations),
start number and the Nation of each shooter (see Rule 6.7.2.9).
These results must be made available to the news media.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.9.3 All shooters must be provided with a Bib (Start) Number for use on
the back of the outer garment above the waistline during the full
time of the competition. The Bib (Start) must display the allocated
number, family name, initials and the nation of the shooter. The IOC
abbreviation of the nation must be used. The height of the letters
should be as big as possible and should not be less than 20 mm (for
Shotgun see also 9.9.4.2).
6.9.4 Progressive, preliminary, and final scores must be displayed on
large scoreboards, to keep the shooters, spectators and the news
media informed at all times. These scoreboards must be located
near the competition ranges, but at a suitable distance to avoid
disturbing the shooters.
6.9.5 A permanent scoreboard must display all the results in as large a
format as possible so that spectators and athletes can see them
easily.

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
6.10.0 INDEX
10 m indoor air gun ranges 6.3.6.3.4
25 m and 50 m indoor ranges 6.3.6.3.3.1
25 m outdoor ranges 6.3.6.3.3
Aiming area – Only one (1) aiming area 6.3.1.6
Allocation of firing points 6.4.2.5
Allocation of firing points – Basic principles 6.5.5
Alteration of equipment after control 6.6.7
Application of ISSF Rules 6.1.2
Automatic Trap Ranges 6.3.20
Awards and Records 6.8.0
Backing boards 25 m targets 6.3.17.12
Backing Cards 6.3.4
Backing Targets – 25 m 6.3.4
Backing Targets – 50 m 6.3.4.1
Bib (Start) Numbers 6.9.3
Certifying of scores by officials 6.7.12
Changes of shooting schedules 6.5.3
Classification Jury 6.7.6
Classification Jury – Electronic Scoring Targets 6.7.6.1
Classification Jury – Independent determination of results 6.7.13
Classification Office 6.7.5
Clay Targets 6.3.2.8
Clock on the range 6.3.6.7
Common Range Standards 6.3.6
Communication on the range 6.3.6.12
Competition area 6.3.6.4
Competition Officials 6.4.0
Conduct of ISSF Championships 6.1.5
Control Sheets 6.3.4
Decision on the value of a shot 6.7.14.4
Decisions – Jury 6.4.1.3
Decisions – Jury – not covered by the ISSF Rules 6.4.3
Decisions of the Classification Jury 6.7.14.7
Deviations of specifications 6.3.5.1.1
Dimensions of scoring rings (outside diameter) 6.3.1.5
Direction of facing targets 6.3.17.3
Distribution of targets 6.4.2.5
Double Trap Ranges 6.3.21
Duties and Function of the Jury 6.4.2
Ear Protection 6.2.3
Electronic Scoring Targets – 10 m Running Target 6.3.2.7.2.2
Electronic Scoring Targets (EST) 6.3.1.8
Entries – Final entries 6.5.1

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
Equipment Control 6.6.0

Equipment Control – Duties of the Organizing Committee 6.6.1
Equipment Control – Information of shooters and team officials 6.6.3
Equipment Control – Marking of equipment and guns 6.6.6
Equipment Control – Registration 6.6.5
Equipment Control – Re-inspection 6.6.8
Equipment Control – Responsibility of the shooter 6.6.2
Equipment Control – Supervision by the Jury 6.6.4
Equipment Control – Validity 6.6.9
Examination and check by the Jury 6.4.2.1
Examination of equipment and guns 6.4.2.4
Examination of Paper and Clay Targets by the Technical Delegate 6.3.1.2
Facing times 25 m targets 6.3.17.14
Final Result List 6.9.2
Final Scores 6.9.4
Firing line 6.3.6.1
Firing line 6.3.8.5
Firing Point Standards for 10 m Ranges 6.3.15
Firing points 6.3.6.1
Function firing range 6.5.7.4
Gauge 4.5 mm INWARD 6.7.15.4
Gauge 4.5 mm OUTWARD – 10 m Air Rifle / 10 m Running Target 6.7.15.5
Gauge for 300m Rifle 6.7.15.2
Gauge for Center Fire Pistol 6.7.15.1
Gauge for Small Bore Rifle and Pistol 6.7.15.3
Gauges – Examination by the Technical Delegate 6.7.15.8
Gauges 4.5 mm OUTWARD – 10 m Air Pistol 6.7.15.6
Gauges for paper targets 6.7.15
General firing point standards 300 m, 50 m, 10 m 6.3.12
General Paper and Clay Target Requirements 6.3.1
General TR 6.1.0
Groups of targets 25 m 6.3.17.4
Groups of targets for the 25 m Rapid Fire Pistol Event 6.3.17.13
Handling of guns 6.2.2
Height of targets 6.3.9
Hits outside the scoring rings 6.7.14.6
Horizontal variations of targets 6.3.10 -6.3.11
Individual shooters – Allocation of firing points 6.5.5.1
Information of shooters and team officials 6.5.2
Inner Ten – Air Rifle 6.7.14.1
Inner Tens 6.3.1.4
Insert a plug gauge 6.7.14.5
Inspection of Ranges by the Technical Delegate 6.3.5.1.1

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
Jury – Check of Electronic Scoring Targets 6.4.2.2

Jury – Decisions 6.4.1.3
Jury – Knowledge and enforcement of the ISSF Rules 6.4.1.2
Jury – Majority 6.4.1.4
Jury – Responsibilities 6.4.1.1
Jury – Supervising 6.4.2.3
Jury of Appeal 6.4.1.4
Line of targets 6.3.6.1
Main scoreboard 6.7.1
Majority – Jury 6.4.1.4
Media Relations 6.9.0
Media Relations: Facilities – assistance – co-operation 6.9.1
Members of the Jury 6.4.4
Men's events 6.1.4
Mobile telephones 6.3.6.6
Mobile telephones – Prohibited in competition area 6.3.6.6.1
Numbering of target frames and firing points 6.3.6.8
Numbering of Targets 6.7.9
Objective and Purpose of ISSF Rules 6.1.1
Official Training World Championships and World Cups 6.5.7.1
Officials area 6.3.6.5
Organization of ISSF Championships 6.1.5
Organizing Committee 6.4.1
Paper Sighting Targets 6.3.3
Paper Target – 10 m Air Pistol 6.3.2.6
Paper Target – 10 m Air Rifle 6.3.2.3
Paper Target – 10 m Running Target 6.3.2.7.2
Paper Target – 25 m Rapid Fire Pistol 6.3.2.4
Paper Target – 300 m Rifle 6.3.2.1
Paper Target – 50 m and 25 m Precision Pistol 6.3.2.5
Paper Target – 50 m Rifle 6.3.2.2
Paper Target – 50 m Running Target 6.3.2.7.1
Paper Targets 6.3.2
Permanent Scoreboard 6.9.5
Plywood used as backing boards 6.3.17.11
Pre-Event Training 6.5.7.2
Preliminary scores 6.7.1
Preliminary Scores 6.9.4
Pre-Match Administration 6.5.0
Presence of the Jury 6.4.2.7
Progressive Scores 6.9.4
Protection against rain, sun, wind 6.3.6.3
Protests 6.4.2.6
Protocol: Awards and Records 6.8.0
Range and Target Standards 6.3.0
Range Officers – Knowledge and enforcement of the ISSF Rules 6.4.1.2
Range Officers – Responsibilities 6.4.1.1

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
Range Standards 6.3.5

Recording of results 6.7.16
Records 6.8.0
Register Keeper's equipment 6.3.6.11
Replacement of a shooter 6.5.4
Responsibility of target transportation 6.7.10
Responsibility of Transportation of Targets 6.7.10
Result lists – Abbreviations 6.7.2.9.2
Result lists – Containing 6.7.2
Result lists – Report to the ISSF Headquarters 6.7.3 - 6.7.4
Running Target – Dry Firing Position 6.3.18.5.1
Running Target – Run times 6.3.18.8
Running Target – Shooter visible to the spectators 6.3.18.5
Running Target – Width of the firing station 6.3.18.5.1
Running Target Ranges 6.3.18.11
Running Target Ranges 10 m 6.3.18.11.2
Running Target Ranges 50 m 6.3.18.11.1
Safety 6.2.0
Safety of ranges 6.3.6.2
Safety of shooters, range officials, spectators 6.2.2
Safety requirements 6.2.1
Samples of Paper and Clay Targets by the ISSF Headquarters 6.3.1.1
Schedules of Shooting Times 6.4.2.5
Scope of Technical Rules 6.1.3
Scoring in the Classification Office 6.7.7
Scoring Procedures 6.7.0
Scoring Procedures in the Classification Office 6.7.11
Scoring zones – Scoring rings 6.3.1.7
Sections (groups) of targets 25 m 6.3.17.5
Shooting Distances 6.3.8
Shooting Distances – Measurement 6.3.8.2
Shooting mats 6.3.12.2.2
Shotgun events – Selection of ranges and rounds 6.5.6
Shots in dispute 6.7.14.2
Signal systems on the range and to the pits 6.3.6.13
Skeet Ranges 6.3.22
Skid Gauge 6.7.15.7
Skid Shots Running Target 6.7.15.9
Smoking 6.3.6.4.1
Spectators area 6.3.6.5.1
Standards 25 m Turning Targets Installations 6.3.17
Standards for 10 m Ranges 6.3.15
Standards for 25 m Ranges 6.3.16
Standards for Running Target Ranges – General 6.3.18
Standards for Shotgun Ranges 6.3.19
Sun – Direction of Ranges 6.3.5.1.2
Systems of targets 6.3.6.10

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs
Target paper 6.3.1.3

Targets – Fixing 6.3.6.9
Targets – No movement 6.3.6.9
Teams – Allocation of firing points 6.5.5.1
Technical Delegate: examination of gauges 6.7.15.8
Technical Delegate: report of World / Olympic Records 6.8.3
Technical Delegate: Shotgun events – selection of ranges and rounds 6.5.6
Technical Delegate: Supervision – allocation of firing points 6.5.5.2
Test of guns (function test) 6.5.7.4
Time of turning of 25 m targets 6.3.17.1
Timing of 25 m Electronic Scoring Targets 6.3.17.15
Timing of turning 25 m targets – Accuracy 6.3.17.8
Timing of turning 25 m targets – Incorrect facing time 6.3.17.10
Timing of turning 25 m targets – Start / Stop 6.3.17.9
Timing Running Target 6.3.18.9
Timing Running Target ISSF Championships 6.3.18.10
Titles and Medals 6.8.7
Titles and Medals – Olympic Games 6.8.7.1
Titles and Medals – Time of awarding 6.8.7.4
Titles and Medals – World Championship 6.8.7.2
Titles and Medals – World Championship – minimum of participants 6.8.7.3
Training 6.5.7
Transportation of Targets 6.7.8
Trap Ranges 6.3.19.1
Turning and timing device 6.3.17.7
Turning of targets 25 m 6.3.17.6
Unofficial Training 6.5.7.3
Use of transparent gauges 6.7.14.3
Value of shots 6.7.14
Verifying of Paper and Clay Targets by the ISSF Headquarters 6.3.1.1
Vibration of 25 m targets 6.3.17.2
Wind flags 50m / 300 m 6.3.7
Women's events 6.1.4
World / Olympic Records – Report by the Technical Delegate 6.8.3
World Records – Indoor Ranges 25 m and 50 m 6.8.2.1
World Records – Minimum of participants 6.8.6
World Records for Juniors male / female 6.8.5
World Records for men / women 6.8.4
World Records: Elimination – Qualification – Finals 6.8.2
World Records: Setting – Equaling – Breaking 6.8.1
23_technical_2005_1st.doc/1/16/2006 3:00:00 PM

Copyright: ISSF
1
2
3
4
5
6
7
8
1 23 4 5 6 78 8 7 6 5 4 32 1
8
7
6
5
4
3
2
1
112.4mm
154.4mm
fs

Copyright: ISSF

23 Technical 2005 2nd

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

23 Technical 2005 2nd

Uploaded by

Copyright:

Available Formats

1

International Shooting Sport Federation

ALL SHOOTING DISCIPLINES

Edition 2005 (Second Printing, 09/2005)

Edition 2005 (Second Printing, 01/2006) - 219 -

- 220 - Edition 2005 (Second Printing, 01/2006)

Edition 2005 (Second Printing, 01/2006) - 221 -

6.1.5 Organization and Conduct of ISSF Championships

- 222 - Edition 2005 (Second Printing, 01/2006)

6.3.0 RANGE AND TARGET STANDARDS

Edition 2005 (Second Printing, 01/2006) - 223 -

6.3.2 Paper Competition Targets

300 Meter Rifle Target

6.3.2.2 50 Meter Rifle Target

50 Meter Rifle Target

Edition 2005 (Second Printing, 01/2006) - 225 -

6.3.2.3 10 Meter Air Rifle Target

10 Meter Air Rifle Target

- 226 - Edition 2005 (Second Printing, 01/2006)

6.3.2.4 25 Meter Rapid Fire Pistol Target

25 Meter Rapid Fire Pistol Target

Edition 2005 (Second Printing, 01/2006) - 227 -

6.3.2.5 25 Meter and 50 Meter Precision Pistol Target

25 Meter and 50 Meter Precision Pistol Target

- 228 - Edition 2005 (Second Printing, 01/2006)

6.3.2.6 10 Meter Air Pistol Target

10 Meter Air Pistol Target

Edition 2005 (Second Printing, 01/2006) - 229 -

6.3.2.7 Running Target

50 Meter Running Target

- 230 - Edition 2005 (Second Printing, 01/2006)

6.3.2.7.2 10 Meter Running Target

Edition 2005 (Second Printing, 01/2006) - 231 -

6.3.2.7.2.2 10 Meter Running Target Electronic Target

The 30.5 mm diameter is a hole.

- 232 - Edition 2005 (Second Printing, 01/2006)

6.3.2.8 Clay Targets (for shotgun events)

A-Weight 105 g ±5 g E-Base Height 11 mm ± 1 mm

Edition 2005 (Second Printing, 01/2006) - 233 -

6.3.3 Paper Sighting Targets

- 234 - Edition 2005 (Second Printing, 01/2006)

6.3.6.3 Protection against rain, sun and wind must be provided in

Edition 2005 (Second Printing, 01/2006) - 235 -

6.3.6.12 A communications system must be provided between the Range

- 236 - Edition 2005 (Second Printing, 01/2006)

6.3.8.3 Shooting distances must be as exact as possible, subject to the

Edition 2005 (Second Printing, 01/2006) - 237 -

6.3.11 Horizontal Variations for Firing Points on 50 m and 10 m

- 238 - Edition 2005 (Second Printing, 01/2006)

Edition 2005 (Second Printing, 01/2006) - 239 -

6.3.15.4 Indoor 10 m ranges must have artificial illumination providing the

A position of meter minimum 1500 lux

6.3.16 Range and Firing Point Standards for 25 m Pistol Ranges

- 240 - Edition 2005 (Second Printing, 01/2006)

6.3.16.3 The firing point must be roofed or covered at a minimum height of

Edition 2005 (Second Printing, 01/2006) - 241 -

Direction for "facing" movement

Direction for "edging" movement

6.3.17.4 In 25 m events, the targets must be placed in:

- 242 - Edition 2005 (Second Printing, 01/2006)

Edition 2005 (Second Printing, 01/2006) - 243 -

- 244 - Edition 2005 (Second Printing, 01/2006)