Professional Documents
Culture Documents
Multi Angular Gearless Drive
Multi Angular Gearless Drive
Abstract— The modern gear drives has been widely applied due to excellent accuracy and reliability. However, the major downside of
even the most efficient gear drive is the low efficiency due to errors like backlash and considerable vibrations. These vibrations engender
noisy operation and cause more wear and tear resulting in low life span. The development of a more efficient multi-angular gearless drive
has been explored relatively unsuccessfully and negligently regardless of its advantages over both gear drives and simple gearless drives.
Recent advances in technologies, material, analytical modeling and simulation capabilities has opened the possibility of major advances
towards the design and development of a reliable, cost effective and ultra-efficient multi-angular gearless drive.
—————————— ——————————
1. INTRODUCTION
slide as well as rotate along the symmetrical holes drilled in
T he motion transmission is relaying the same type of
motion from one part of an object to another (rotational to
rotational, translational to translational).Multi-Angular
discs also called as ‘Sliding Pairs’, because motion captured
by naked eyes is sliding one.
Gearless Drive is a motion transmitting device used for
transmitting motion at multiple angles between the driving 4. MECHANISM
and the driven shaft. The scrutiny of this mechanism would Motion is transmitted from driving to the driven shaft through
reveal that it comprises of pins ranging from 3 to 8 pins per the sliding pairs which remain either straight or bent using
assembly and with increase in the number of pins operation universal joints, as per requirement between the shafts.
becomes smoother. These pins slide inside symmetrically These sliding pairs are placed in equally spaced holes
spaced holes machined on solid cylindrical disc. Thus, the around a solid cylindrical disc, which allow it to move freely.
IJSER
sliding pairs help the shaft to revolve at various angles. Thus, when the torque is applied at the input shaft, a uniform
torque is generated at the output.
2. OBJECTIVE Depending on the precision with which the gearless drive
The main objective of the project is to analyze, validate and has been designed and the limitation of the universal joint,
obtain the most optimal design for the Multi-Angular the angular range within which the Multi-Angular Gearless
Gearless drive. The second most important objective is to drive would operate smoothly is decided. This type of drive
discover its scope and applications. is especially suitable where quite operation at high speed
and at various angles is required. Also, this type of gearless
3. DESIGN drive has low vibrations as compare to other motion
transmission systems like simple universal joint which
The scrutiny of the Multi-Angular Gearless Drive mechanism makes it preferable.
would reveal that it comprises of a number of pins ranging
from 3 to 8, our project has three such pins, more the pins
smoother the operation. Every pin is capable of turning at
5. APPLICATIONS:
varied angles by virtue of universal joints. The design has 1- Wind powered gearless power generation.
two discs with three equal holes symmetrically machined 2- Angular machining i.e. shape cutting.
each to the driving and driven shaft. Various pins 3- Movement of periscope in submarines.
————————————————
Ashish Kumar, Asst. Prof. SRM University, Ghaziabad (U.P.), India -
E-mail:[email protected]
IJSER © 2015
http://www.ijser.org
975
International Journal of Scientific & Engineering Research, Volume 6, Issue 7, July-2015
ISSN 2229-5518
IJSER
976
International Journal of Scientific & Engineering Research, Volume 6, Issue 7, July-2015
ISSN 2229-5518
6. ANALYSIS
6.1 Motor Selection
The model development was to be undertaken on a
specific motor selected to meet all the desired torque
requirements as per our design. Selection of motor
configuration is based on moment of inertia of input shaft
i.e 0.63 (based on modelling in Solidworks).
Motor Power, P = 2πNT/60
Where, N = Revolution per Minute
T = Torque transmitted by motor to input shaft (T=Iα)
Net Power Transmitted = Input Power – Frictional Losses
in Joints and Sliding Pairs
Figure 8 – Seperation Distance (b/w Rod and Disc) vs. Time
6.2 Mechanism Analysis
By conducting mechanism analysis, we obtained cogent
information about various parameters and their relations
such as position, velocity, acceleration, etc. from
kinematic analysis. While from dynamic analysis, we
found out all the forces and moments acting on the
various components of the system.
6.3 Static and Modal Analysis
Various results which we obtained from above analysis
were utilised for defining constraints and forces applied at
various positions. Thus, obtaining stress, strain,
displacement, and factor of safety plots for the designed
model to standarize the dimensions.
Figure 5 – Output Shaft Velocity vs. Time
IJSER
Figure 9 – Von Mises Stress Plot
Figure 6 – Output Shaft Acceleration vs. Time
IJSER © 2015
http://www.ijser.org
977
International Journal of Scientific & Engineering Research, Volume 6, Issue 7, July-2015
ISSN 2229-5518
7. CONCLUSION
Designing of Multi-angular gearless drive instigated with
assumptions and random dimensions because no significant
development has been done before in this unchartered
territory. With software support and assiduous endeavour the
final optimal design has been obtained. The final design thus
obtained is capable of transmitting torque and power at
varied angles depending on the angular limitation of the
hooks joint. With further research and advanced analysis in
the design wide-ranging applications of the drive can be
discovered.
Figure 11 – Strain Plot
REFERENCES
[1] The Meccano Magazine ―(106)-A Curious Right-Angle
Drive‖ Pg. No. 1079, Print-1927
[2] Charles Kostka ―A PIN-AND- SLOT, ANGLE-DRIVE
WRENCH‖ Ser. No. - 735276
[3] Jack W. Stage ―LIMITED ANGLE UNIVERSAL
JOINT‖ Patent No. - S6287206B1
[4] V B Bhandari ―Design of Machine Elements‖ Tata
McGraw Hill Education, 2010
[5] S S Rattan ―Theory of Machines‖ Tata McGraw Hill
Education, 2009
[6] R S Khurmi, J K Gupta ―Theory of Machines‖ S.Chand
Publications, 2009
IJSER
Figure 13 – Factor Of Safety Plot
[7] Sadhu Singh ―Theory of Machines‖ Pearson Education,
2009
IJSER © 2015
http://www.ijser.org