Professional Documents
Culture Documents
Micro Ondas NN-ST252W Original Ingles
Micro Ondas NN-ST252W Original Ingles
MOD1006319 PE
Microwave Oven
Model No. NN-ST252WRUN
NN-ST252WRUK
20L
White
Brazil
s
NN-ST252WRUN NN-ST252WRUK
Power Requirement 127 Volts AC 60 Hz 220 Volts AC 60 Hz
1,250 Watts (11.0 A) 1,250 Watts (6.0 A)
Single phase, 3 wire grounded Single phase, 3 wire grounded
SAFETY PRECAUTIONS
This device is to be serviced only by properly qualified service personnel.
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be
taken to avoid possible exposure to excessive microwave energy.
CAUTION
MICROWAVE RADIATION
DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR
OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.
CONTENTS
(Page)
SPECIFICATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1
CAUTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1
INSTALLATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1
FEATURES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
CONTROL PANEL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
Inside
Accessories
Instruction manual
Glass Tray
Roller Ring
1-1
CAUTIONS
ANTENNA
GASKET
COOLING FIN
FILAMENT
TERMINALS
MAGNETRON
CHASSIS GROUND
2-1
INSTALLATIONS
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
3-1
OPERATING INSTRUCTIONS
FEATURES
Oven Front Plate
See-Through oven window
Door C
Control Panel
Glass Tray
Roller Ring
CONTROL PANEL
NN-ST252WRUN / NN-ST252WRUK
(1) Display
(2) Power Selection Tab
(1) (3) Number Tabs
(4) Memory Tab
(5) Timer / Clock Tab
(6) + 30 sec. Tab
(7) Auto Cook Options
(8) Defrost Tab
(2) (9) Serving / Weight Tab
(10) Stop / Cancel Tab
(3) Before Cooking: one tap cancels the inserted instructions.
During Cooking: one tap temporarily stops the cooking
process. Another tap cancels cooking.
(5) (11) Start Tab
(4) One tap begins oven functioning.
(6)
Beep Sound:
(7) When a pad is pressed correctly, a beep will be heard.
If a pad is pressed and no beep is heard, the unit did
not or cannot accept the instruction. The oven will beep
twice between programmed stages. At the end of any
complete program, the oven will beep 5 times.
(9)
(8)
(10) (11)
4-1
OPERATING SEQUENCE
The following is a description of component functions
during oven operation.
4-2
SCHEMATIC DIAGRAM
4-3
CIRCUIT DESCRIPTION
GENERAL DETAILS power of microwave oven as POWER LEVEL.
(refer to page 1-1)
• The low voltage transformer supplies the necessary
voltage to the micom controller when power cord is WHEN THE DOOR IS OPENED DURING
plugged in.
COOKING
• When the door is closed, the primary switch is ON, the
• Both the primary switch and relay 2 are cut off primary
secondary switch is ON, and the monitor switch opens
winding voltage of the high voltage transformer.
(contact COM and NO).
• ON-OFF of relay 2 is coupled electrically with opening
and closing of the secondary switch.
WHEN SELECTING COOKING POWER • When the door is opened, the secondary switch is
LEVEL AND TIME opened and when the door is closed, the secondary
• The micom controller memorizes the function you set. switch is closed.
• The time you set appears in the display window. • The cooking time stops counting down.
• Each indicator light turns on to indicate that the stage • Relay stops functioning.
has been set. • As the door is opened, if the contact of primary switch
and relay 2 and/or secondary switch fails to open, the
WHEN TOUCHING THE START PAD fuse opens due to the large current surge caused by
• The coil of the relay is energized by the micom the monitor switch activation, which in turn stops
controller. magnetron oscillation.
• Power input is supplied to the high voltage transformer PRIMARY
FUSE SWITCH
through the fuse to the primary switch and relay 2.
• Turntable rotates.
FUSE PRIMARY L
SWITCH
MONITOR
SWITCH FORMER
L N
MONITOR TRANS-
SWITCH FORMER
N RELAY 2 SECONDARY
SWITCH
MICOM CONTROLLER
RELAY 2 SECONDARY
SWITCH
MICOM CONTROLLER
4-4
SERVICE INFORMATION
TOOLS AND MEASURING INSTRUMENTS
NECESSARY TOOLS NECESSARY MEASURING INSTRUMENTS
Tools normally used for TV servicing are sufficient. • TESTER(VOLTS-DC, AC., Ohmmeter)
Standard tools are listed below. • Microwave survey meter
• Diagonal pliers - Holaday HI-1500
• Long nose pliers HI-1501
• Phillips screwdriver - Narda 8100
• Flat blade screwdriver 8200
• Wrench (size 5mm) • Inch scale
• Nutdriver (size 5mm) • 600 cc non conductive material beaker (glass or plastic),
• Adjustable wrench inside diameter: approx. 8.5 cm(31/2 in.)
• Soldering iron • Cylindrical and made of borosilicate glass vessel.
• Solder max. thickness: 3 mm
• Vinyl insulation tape outside diameter: approx. 190mm
• Polishing cloth height: approx. 90mm
• Glass thermometer: 100°C or 212°F (1 deg scale)
5-1
MEASUREMENT WITH OUTER CASE NOTES WHEN MEASURING
REMOVED • Do not exceed meter full scale deflection.
• When you replace the magnetron, measure for • The test probe must be removed no faster than
microwave energy leakage before the outer case is 1 inch/sec (2.5 cm/sec) along the shaded area,
installed and after all necessary components are otherwise a false reading may result.
replaced or adjusted. • The test probe must be held with the grip portion of the
Special care should be taken in measuring the handle.
following parts. (Circled area of below Fig.) A false reading may result if the operator's hand is
- Around the magnetron between the handle and the probe.
- The waveguide • When testing near a corner of the door, keep the probe
perpendicular to the surface making sure the probe
horizontally along the oven surface, this may possibly
WARNING : AVOID CONTACTING ANY cause probe damage.
HIGH VOLTAGE PARTS
RECORD KEEPING AND NOTIFICATION
AFTER MEASUREMENT
• After adjustment and repair of any microwave energy
interruption or microwave energy blocking device,
record the measured values for future reference. Also
enter the information on the service invoice.
• The microwave energy leakage should not be more
than 4 mW/cm2.sq. after determining that all parts are
in good condition, functioning properly and genuine
replacement parts which are listed in this manual have
been used.
• At least once a year, have the electromagnetic energy
leakage monitor checked for calibration by its
manufacturer.
5-2
MEASUREMENT OF MICROWAVE POWER OUTPUT
• Microwave power output measurement is made with is measured while the microwave generator is
the microwave oven supplied at its rated voltage and operating at full power. Magnetron filament heat-up
operated at its maximum microwave power setting with time is not included. (about 3 sec)
a load of (1000±5) g of potable water. • The water is stirred to equalize temperature throughout
• The water is contained in a cylindrical borosilicate glass the vessel, prior to measuring the final water
vessel having a maximum material thickness of 3 mm temperature.
and an outside diameter of approximately 190mm. • Stirring devices and measuring instruments are
• The oven and the empty vessel are at ambient selected in order to minimize addition or removal of
temperature prior to the start of the test. heat.
• The initial temperature (T1) of the water is (10±2)°C. It
is measured immediately before the water is added to
the vessel. After addition of the water to the vessel,
the load is immediately placed on the center of the WATER LOAD
turntable which is in thd lowest position and the
microwave power switched on.
• The time T for the temperature of the water to rise by a
value ∆ T of (10±2)°K is measured, where T is the time
in seconds and ∆T is the temperature rise. The initial TURNTABLE
and final water temperatures are selected so that the
maximum difference between the final water
temperature and the ambient temperature is 5°K. NOTES:
• The microwave power output P in watts is calculated For simple tests of micromave power output, conduct
from the following formula :
it by heating one litre water for one minute,
4187 x (∆T) + 0.55 X (T2 - T0 ) X M minimum temperature rise should be 6 °C
P=
T
• T2: Temperature after heating
• T0: Temperature of bowl
• M: Weight of bowl
5-3
D. DOOR ASSEMBLY REMOVAL E. HIGH VOLTAGE TRANSFORMER
1) Open the door. REMOVAL
2) Remove two screws holding the Hinge 1) Discharge the high voltage capacitor.
to the Cavity Ass'y. 2) Disconnect the leadwire from magnetron, high voltage
CAUTION : Be careful not to damage Door C transformer, and capacitor.
by screwdriver. 3) Remove the screw holding the high voltage
3) Lift up and pull the door. transformer to the baseplate.
NOTE:
1. After replacing the door, be sure to check that the F. ORIFICE ASSEMBLY REMOVAL
primary switch, monitor switch, and secondary switch 1) Discharge the high voltage capacitor.
operate normally. 2) Disconnect the leadwire from fan motor, noise filter
2. After replacing the door, check for microwave energy and high voltage capacitor.
leakage with a survey meter. Microwave energy must 3) Remove the two screws holding the orifice ASS’Y
be below the limit of 5 mW/cm2. (with a 275 ml water to the oven cavity and remove the high voltage diode
load) earth screw.
3. When mounting the door assembly to the oven 4) Remove the screw of the capacitor bracket.
assembly, be sure to adjust the door assembly parallel 5) Remove the two screws holding the fan motor ASS’Y
to the chassis. Also adjust so the door has no play to the Orifice ASS’Y.
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
G. HIGH VOLTAGE CAPACITOR AND
properly, microwaves may leak from the clearance
between the door and the oven. DIODE REMOVAL
1) Discharge the high voltage capacitor.
Remove door Assembly 2) Disconnect the leadwire from fan motor, noise filter
and high voltage capacitor.
3) Remove the screw holding the Orifice ASS’Y to
the oven cavity and remove the high voltage diode
earth screw.
4) Remove the screw holding the high voltage capacitor
bracket.
5-4
H. AIR GUIDE ASSEMBLY REMOVAL J. REMOVING THE TURNTABLE MOTOR
1) Disconnect the leadwire from lamp, A.C Relay and 1) Remove the glass tray.
monitor resistor and magnetron. 2) Remove the pully shaft VERY CAREFULLY
2) Remove the screw to the cavity. 3) Lay the unit down on its back.
4) Remove the turntable motor cover.
The turntable base cover is easily removed by
I. MAGNETRON REMOVAL pinching the six parts with a wire cutting.
1) Disconnect the leadwire from the high voltage 5) Disconnect the leadwire from the turntable motor
transformer and high voltage capacitor. terminals.
2) Remove the air guide. 6) Remove the screw securing the turntable motor to
3) Carefully remove the mounting screws holding the the oven cavity ASS’Y
magnetron and the waveguide. 7) After replacing the motor, rotate the removed
4) Remove the magnetron until the tube is turntable motor cover.
clear from the waveguide. 8) Fit the turntable motor cover’s projecting part to the
base plate slit.
NOTE:
1. When removing the magnetron, make sure its NOTE:
dome does not hit any adjacent parts, or it may be 1. Remove the wire lead from the turntable motor
damaged. VERY CAREFULLY.
2. When replacing the magnetron, be sure to install 2. Be sure to grasp the connector, not the wires, when
the magnetron gasket in the correct position and removing
be sure that the gasket is in good condition.
3. After replacing the magnetron, check for microwave
leakage with a survey meter around the
magnetron. Microwave energy must be below the
limit of 5 mW/cm2. (With a 275 ml. water load).
Make sure that gasket is rigidly attached to the
magnetron. To prevent microwave leakage, tighten the
mounting screws properly, making sure there is no gap
between the waveguide and the magnetron.
Base plate
Magnetron
Magnetron
Magnetron
Gasket
Waveguide
Bracket
Dome
Waveguide
5-5
K. PCB ASSEMBLY REMOVAL L. INTERLOCK SYSTEM
1) INTERLOCK MECHANISM
1) Remove the control panel assembly from the
The door lock mechanism is a device which has
cavity.
been specially designed to eliminate completely
2) Remove screws which hold the PCB to the microwave activity when the door is opened during
control panel. cooking and thus to prevent the danger resulting
3) Disconnect the flat cable from the PCB and from the microwave leakage.
take off the PCB .
2) MOUNTING OF THE PRIMARY/MONITOR/
SECONDARY SWITCHES TO THE LATCH
BOARD
ADJUSTMENT
S03
DIRECTION
C55
PRIMARY
C
01 SWITCH
C05
MONITOR
SWITCH
SECONDARY
SWITCH
H.V. TRANSFORMER
H.V.
DIODE
H.V. CAPACITOR
PRIMARY
5-6
INTERLOCK CONTINUITY TEST
WARNING : FOR CONTINUED PROTECTION AGAINST EXCESSIVE RADIATION
EMISSION, REPLACE ONLY WITH IDENTICAL REPLACEMENT PARTS.
Primary
Switch COM
NO
Type No.KW3A
Monitor NC
Switch COM
Type No.KW3A
Secondary NO
COM
Switch
Type No.KW3A
NOTE : After checking for the continuity of switches, make sure that are
correctly connected.
5-7
COMPONENT TEST PROCEDURE
CAUTIONS
1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE
OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)
2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER
OF WATER IN CONTAINER) IN THE OVEN.
SECONDARY
WINDING
PRIMARY
TERMINAL
MAGNETRON
(Wire leads removed)
1. Measure the resistance.
(Ohm-meter scale: Rx1) Normal: Less than 1 ohm
• Filament terminal
5-8
COMPONENTS TEST PROCEDURE RESULTS
Antenna
Gasket
Chassis
Filament
NOTE: When testing the magnetron, be sure to install the magnetron gasket
in the correct position and be sure that the gasket is in good condition.
*NOTE :
Some inexpensive meters
may indicate infinite
resistance in both direction. Measure the continuity (Reverse). Normal: ∞
(Ohm-meter scale: Rx10000) Abnormal: Continuity.
5-9
COMPONENTS TEST PROCEDURE RESULTS
FUSE Check for continuity of the fuse with an Normal Abnormal
multi-meter.
NOTE: If the fuse is blown, check the primary, the secondary, and the monitor switches,
H.V.D. and H.V.C. before replacing the fuse.
If the fuse is blown by improper switch operation replace the defective switch and the
fuse at the same time. Replace just the fuse if the switches operate normally.
Below specified Above specified
THERMAL temperature temperature
CUT-OUT
1 3 5
5-10
COMPONENTS TEST PROCEDURE RESULTS
FAN MOTOR Measure the resistance. Normal: 100~500 Ω
(Wire leads removed) (Ohm-meter scale: R x 100) Abnormal: ∞ or several Ω
NOTE : • A MICROWAVE LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.
• MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.
• WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE
CONNECTOR, NOT THE WIRES.
5-11
TROUBLE SHOOTING
WHEN YOU GET A COMPLAINT FROM YOUR CUSTOMER, EVALUATE THE COMPLAINT CAREFULLY. IF
THE FOLLOWING SYMPTOMS APPLY, PLEASE INSTRUCT THE CUSTOMER IN THE PROPER USE OF THE
MICROWAVE OVEN. THIS CAN ELIMINATE AN UNNECESSARY SERVICE CALL.
CAUTIONS
1. Check grounding before checking for trouble.
2. Be careful of the high voltage circuit.
3. Discharge the high voltage capacitor. (See page 2-1)
4. When checking the continuity of the switches or of the high voltage transformer, disconnect one lead wire
from these parts and then check continuity with the AC plug removed. To do otherwise may result in a
false reading or damage to your meter.
5. Do not touch any part of the circuitry on the digital programmer circuit since static electric discharge may
damage this control panel.
Always touch yourself ground while working on this panel to discharge any static charge built up in your
body.
Microwave oven Inserting many plug into one Avoid using other electrical
does not work. plug outlet and using appliances when you use the
them at the same time microwave oven.
(causes overloading).
Output power is too low. Low AC input voltage. Use the microwave oven at
adequate line voltage.
Sparks occurring. Using metallic ware and Do not use metallic ware for
allowing it to touch the oven cooking except where noted
wall. in the cooking guide.
5-12
(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.
1. Incomplete segments.
• Segment missing.
• Partial segment missing.
• Digit flickering (NOTE: Slight flickering is normal.)
2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display indicates a number different from one touched, for example, key in 5 and 3 appears in the display.
6. Specific numbers (for example 7 or 9) will not display when key pad is touched.
7. Display does not count down with time blinking or up with clock operation.
8. Display obviously jumps in time while counting down.
9. Display counts down too fast while cooking.
10. Each indicator light does not turn on after setting cooking cycle.
11. Display time of day does not reappear when cooking is finished.
12. Beep sound is not heard when correct key is touched.
2. Some inputs Replace key Everything works Defective key Replace key
cannot be membrane as specified. membrane membrane
programmed. assembly and assembly. assembly.
check operation.
Still have
3. Display shows a trouble. Defective PCB Replace PCB
number or figure assembly. assembly.
different from one
touched.
4. Random
programming
when touching
other pads.
5. Display is fixed
at some figure
and can not
accept any
input.
5-13
(TROUBLE 2) Oven does not operate at all ; Display window does not display any figures and
no input is accepted.
Replace fuse
NOTE : All these switches must be replaced at the same time. Refer to page 5-6, 5-7
Continuity.
Check continuity
No continuity. Defective power Replace power
of power supply
cord. supply cord. supply cord.
5-14
(TROUBLE 3) Display shows all figures set, but oven does not start cooking while
desired program times are set and START pad is touched.
Normal.
5-15
(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run
(Display operates properly)
normal
normal
normal
normal
5-16
(TROUBLE 6) Oven does not cook properly when programmed for the set power level
(Operates properly on HIGH)
5-17
EXPLODED VIEW
INTRODUCTION
INTERIOR PARTS
6-1
DOOR PARTS
08
D05
D04
S03
D01
D07
D06
D02
D03
6-2
CONTROL PANEL PARTS
C18
S03
C55
C
01
C05
6-3
OVEN CAVITY PARTS
6-4
LATCH BOARD PARTS
6-5
INTERIOR PARTS
6-6
BASE PLATE PARTS
6-7
REPLACEMENT PARTS LIST
NOTE:
1. When ordering replacement part(s), please use part number(s) shown in this part list.
Do not use description of the part.
2. Important safety notice:
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacture’s specified parts.
For model:NN-ST252WRUN
Ref. No. Midea Part No. Part Name&Description Pcs/Set Remarks
A01 262100100003 CEILING COVER 1
B01 261501411503 BASE 1
B02 256302002774 RUBBER FOOT 4
B03 261502500200 LOWER HINGE 1
C01 ! 261300268001 ESCUTCHEON BASE 1
C17 261400209420 MEMBRANE SWITCH(U) 1
C18 261400124990 PCB ASSY 1
C55 ! 261515903300 ESCUT.BACK PLATE 1
D01+D02+D03
+D04+D05+D0 -263600205243 DOOR ASS'Y 1
6+D07+D08
D01 ! 251500200068 DOOR E 1
D02 251300500045 DOOR KEY A 1
D03 252010000000 DOOR KEY SPRING 1
D04 251502401256 TOP DOOR HINGE 1
228*144*0.1 (For
D05 ! 252200400489 DOOR SCREEN A 1
DOOR E)
D06 262100402988 DOOR SCREEN B 1
D07 ! 261300142900 DOOR A 1
D08 ! 256300600039 DOOR C 1
E01 ! 251200100837 MAGNETRON 1 2M217J
E05 ! 261200201752 H.V.TRANSFORMER 1
E06 ! 251200701300 H.V. CAPACITOR 1
E07 ! 251200900861 DIODEL, SI 1
E11 ! 261201200040 FUSE 1
7-1
REPLACEMENT PARTS LIST
For model:NN-ST252WRUN
7-2
REPLACEMENT PARTS LIST
NOTE:
1. When ordering replacement part(s), please use part number(s) shown in this part list.
Do not use description of the part.
2. Important safety notice:
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacture’s specified parts.
For model:NN-ST252WRUK
Ref. No. Midea Part No. Part Name&Description Pcs/Set Remarks
A01 262100100003 CEILING COVER 1
B01 261501411503 BASE 1
B02 256302002774 RUBBER FOOT 4
B03 261502500200 LOWER HINGE 1
C01 ! 261300268001 ESCUTCHEON BASE 1
C17 261400209420 MEMBRANE SWITCH(U) 1
C18 261400124990 PCB ASSY 1
C55 ! 261515903300 ESCUT.BACK PLATE 1
D01+D02+D03
+D04+D05+D0 -263600205243 DOOR ASS'Y 1
6+D07+D08
D01 ! 251500200068 DOOR E 1
D02 251300500045 DOOR KEY A 1
D03 252010000000 DOOR KEY SPRING 1
D04 251502401256 TOP DOOR HINGE 1
D05 ! 252200400489 DOOR SCREEN A 1 228*144*0.1 (For DOOR E)
D06 262100402988 DOOR SCREEN B 1
D07 ! 261300142900 DOOR A 1
D08 ! 256300600039 DOOR C 1
E01 ! 251200100837 MAGNETRON 1 2M217J
E05 ! 261200200891 H.V.TRANSFORMER 1
E06 ! 251200701309 H.V. CAPACITOR 1
E07 ! 251200900861 DIODEL, SI 1
E11 ! 251201200024 FUSE 1
7-3
REPLACEMENT PARTS LIST
For model:NN-ST252WRUK
7-4
1 2 3 4 5 6 7 8
R103 C101 102,1KV
20R +12
85-265VAC D100 D101
C100
R102 T100
BCK16-D2128
UF4002
CN100 1N4007 1N4007 100K 10 D106 E103 R106
102,1KV
MOTOR 1 470uF,25V 4K7
5 R111 12V
E100 2 VCC
R101 100K 89 D107
100R IN
+12 4.7uF,450V 4.7uH,0.3A
LED share kathode 5V UF4002 E102 E104
N E101 4 L100
3
(共阴极数码管) ZR1 67 470uF,25V 220uF,16V
D R1 线绕电阻 4.7uF,450V D102 D
LED: 4X8 D4 D3 D2 D1
561
3.3k 4148 1448 4148 4148
1N4007
L RX
1 R105
22R,2W
SCHEMATIC DIAGRAM OF P.C.B
5
LED1 102
Q1
BUZ1 3492AG IC100
C
C3
C1
C4
D
B S IC101
4 3 2 Z100
4.7K FB
E
7 1N5229B,4.3V(2%)
R2 S
3 4 1
2K R107 BP
2
S
S
D103 D104 3K9 C102
PC817C
A
G
B
1
L101
5
10
11
12 20K
2.2mH,0.1A
RY IC102 R110
1 4 ZERO
220K,1W 1K
D105 2 3 C103
金属氧化膜电阻 1N4007 102
PC817C
R14 R15 R16 R17 R18 R19 R20 R21 烧烤/非烧烤机型选择说明:
220 220 220 220 220 220 220 220 VCC
1.烧烤型不装R36,装烧烤继电器部分电路(包括R37 ).
2.非烧烤型只装R36,不装烧烤继电器部分电路(包括R37)
R36
key i n 5(键入5)
key i n 4(键入4)
key i n 3(键入3)
key i n 2(键入2)
key i n 1(键入1)
key i n 0(键入0)
1
47k
C Q2 C
C
CN2 R24 S8050 RLY1
2K B GRIIL
R8 key in 5(键入5) 3K3
10
E
R9 2K key in 4(键入4) R35
9 2K 2K
R10 key in 3(键入3) D10
2
8 2K
R11 key in 2(键入2) 4148
7 2K
R12 key in 1(键入1)
6 2K
R13 key in 0(键入0)
5
4
3
1
DOOR
2
IC1 Q3
C
1 R25 RLY2
15 14 MICRO S8050
CON10 LED-D/PH1 PH0/LED-D B MICRO
8-1
SWE 3K3
E
16 13 R27 4K7
C6 C7 C8 C9 C10 C11 LED-D/PD2 PD1/LED-C
SWD D12
2
17 12 R28 4K7 4148
471 471 471 471 471 471 LED-D/PD3 PD0/LED-C
SWC
18 11 R29 4K7
LED-D/PB0 PA3/LED-C
SWB
19 10 R30 4K7
LED-D/PB1 PA2/LED-C
SWA
20 9 R31 4K7
LED-D/PB2 PA1/LED-C
SINO
VCC 21 8
LED-D/PB3 PA0/LED-C
22 7 C15
VDD GND
SH69P26
B R26 B
C12 23 6 0.1uF RESET
OSCI/PC0 PC3/RESER VCC
15P VCC
1K
24 5 LAMP/FAN
OSCO/PC1 PC2/T0
OSC BUZZER
25 4 MICRO R34
TONE/PF0 PE0/CMPO
C13 4MHz 10K
15P 26 3 GRILL D11
T2/PF1 PE1/CMPN 2K R33
GND
R7 DOOR
100K 27 2 KSCAN3
PF2 PE2/CMP1 C17
4148 +12
KSCAN1 ZERO
28 1 KSCAN2 471
1
PF3 PE3/CMP2 C16
SDA/KSCAN0 VCC DOOR
SH69P26-28PIN 0.1uF CN2 N
Q6
E
R37 R38
1
S8550
B
Q4
C
R41
C
4.7K 10K S8050 RLY3
E
B LAMP
B 1K
E
R39 R40
C
D14 MOTOR
2
Q7 220 10K C19
4148
S8550 10uF/16V R42
4.7K
A A
1 2 3 4 5 6 7 8