ELT400 DataSheet
ELT400 DataSheet
Exposure Level Tester ELT-400 Direct Evaluation of Field Exposure Automatic Exposure Evaluation
for Various Waveforms
19
USA TEL: (1) 631 231-1700 FAX: (1) 631 231-1711 E-MAIL: [email protected] www.narda-sts.us
Basic Operation
The ELT-400 covers the wide frequency range of 1 Hz to 400 kHz which is far beyond the reference limits of common guidelines. This instrument has an external isotropic magnetic field probe with a 100 cm2 cross-sectional area, making it suitable for standards-compliant measurement even in inhomogeneous fields. The ELT-400 has a rugged housing and is easy to operate using only six buttons. The instrument settings and measurement results are clearly displayed on a backlit LCD display. An optional probe extension cable is especially designed for low influence on the frequency response and sensitivity of the instrument. This cable is a good choice in cases where the probe and instrument must be handled separately. The ELT-400 is available with different operating mode combinations, e.g., Exposure STD or Field Strength. See Ordering Information section for details.
20
USA TEL: (1) 631 231-1700 FAX: (1) 631 231-1711 E-MAIL: [email protected] www.narda-sts.us
21
USA TEL: (1) 631 231-1700 FAX: (1) 631 231-1711 E-MAIL: [email protected] www.narda-sts.us
Specications a
ELT - 400 with 100 cm2 Probe Frequency Range (-3 dB), selectable Antenna Type Sensor Type Damage Level RMS Damage Level Peak Measurement Uncertainty d Mounting Thread 1 Hz to 400 kHz, 10 Hz to 400 kHz, 30 Hz to 400 kHz Magnetic (B) Field Isotropic Coil 100 cm2 160 mT The damage level reduces linearly with increasing frequency above 77.5 Hz (1/f ) 226 mT The damage level reduces linearly with increasing frequency above 620 Hz (1/f )
The damage level (peak) applies for pulse duration 15.6 ms and duty cycle 1/64
4% (50 Hz to 120 kHz) 1/4-20UNC-2B (standard thread) Comparison with Standard (see Ordering Information) ICNIRP LOW 160% 1% HIGH 1600% 5% LOW 160% 0.4% 0.001% Automatic according to Selected Standard or RMS (averaging time 1 s) or Peak Value Instantaneous or Max Hold Flat 320 T LOW 32 T 60 nT HIGH 320 T 320 nT LOW 800 T 1 T 1 nT RMS (averaging time 1 s) or Peak Value Instantaneous or Max Hold Three Channel (X-Y-Z) The open-circuit analog output voltage is 800 mV when the field strength value corresponds to the overload limit (sensitivity = 800 mV / overload limit) (ELT-400 output impedance = 50 , load impedance 10 k) RS-232 (19200 baud, 8n1, XON/XOFF), 3-Wire, 2.5 mm Stereo Jack 8 mT HIGH 8 mT 8 T LOW 8 mT 10 T 80 mT HIGH 80 mT 80 T BGV B11 HIGH 1600% 2% LOW 160% 0.4% EN 50366 HIGH 1600% 2%
GENERAL SPECIFICATIONS
Operating Temperature Range Operating Humidity Range Weight, Typical Dimensions, Typical Display Type Battery Operating Life, Typical Charger Unit Charging Time, Typical Calibration Interval, recommended -10C to +50C <95% (30C) or <29 g/m3, non-condensing 2 lbs. (910 g) with probe 7.1 x 3.9 x 2.2 inches (180 x 100 x 55 mm) without probe / probe 11.8 x 4.9 inches (300 x 125 mm) LCD with Backlight; refresh rate 4 times per second NiMH Batteries (4 x Mignon, AA), exchangeable 12 hours 100 to 240 V AC / 47 to 63 Hz, fits all AC line connectors 2 hours 24 Months
22
USA TEL: (1) 631 231-1700 FAX: (1) 631 231-1711 E-MAIL: [email protected] www.narda-sts.us
Specications (cont) a
ELT - 400 with 3 cm2 Probe Frequency Range (-3 dB), selectable Antenna Type Sensor Type Damage Level RMS Damage Level Peak Measurement Uncertainty d Mounting Thread 1 Hz to 400 kHz, 10 Hz to 400 kHz, 30 Hz to 400 kHz Magnetic (B) Field Isotropic Coil 3 cm2 1500 mT The damage level reduces linearly with increasing frequency above 30 Hz (1/f ) 2121 mT The damage level reduces linearly with increasing frequency above 240 Hz (1/f )
The damage level (peak) applies for pulse duration 15.6 ms and duty cycle 1/64
6% (50 Hz to 120 kHz) 1/4-20UNC-2B (standard thread) Comparison with Standard (see Ordering Information) BGV B11 EN 50366 HIGH LOW HIGH LOW HIGH 15,000% 1500% 15,000% 1500% 15,000% 50% 4% 20% 4% 20% 0.001% Automatic according to Selected Standard or RMS (averaging time 1 s) or Peak Value Instantaneous or Max Hold Flat 8 mT HIGH 3 mT 3.2 T LOW 7.5 mT 10 T HIGH 75 mT 80 T LOW 75 mT 100 T
1 nT RMS (averaging time 1 s) or Peak Value Instantaneous or Max Hold Three Channel (X-Y-Z) The open-circuit analog output voltage is 800 mV when the field strength value corresponds to the overload limit (sensitivity = 800 mV / overload limit) (ELT-400 output impedance = 50 , load impedance 10 k) RS-232 (19200 baud, 8n1, XON/XOFF), 3-Wire, 2.5 mm Stereo Jack
-10C to +50C <95% (30C) or <29 g/m3, non-condensing 1.9 lbs. (840 g) with probe 7.1 x 3.9 x 2.2 inches (180 x 100 x 55 mm) without probe / probe 9.8 x 1.3 inches (250 x 32 mm) LCD with Backlight; refresh rate 4 times per second NiMH Batteries (4 x Mignon, AA), exchangeable 12 hours 100 to 240 V AC / 47 to 63 Hz, fits all AC line connectors 2 hours 24 Months
23
USA TEL: (1) 631 231-1700 FAX: (1) 631 231-1711 E-MAIL: [email protected] www.narda-sts.us
Ordering Information
ELT-400 SET Calibrated Basic Unit and B-Field Probe (100 cm2), Certificate of Calibration, Charger (fits all AC line connectors), Operating/Programming Manual, and Rechargeable Batteries EXPOSURE STD: EN 50366 (IEC 62233) EXPOSURE STD: ICNIRP occ. FIELD STRENGTH: 320 T FIELD STRENGTH: 80 mT ACCESSORIES SUPPLIED: Probe Extension Cable (length 1 m) Serial Interface Cable (length 2 m) Stereo Jack / DB9 Analog Interface Cable (length 3 m) D-SUB15 / 3xBNC Transport Case OPTIONAL ACCESSORIES: Tripod, non-conductive (height 1.65 m) Tripod Extension, non-conductive (height 0.5 m) B-field Probe 3 cm2 (Upgrade required for all ELT 400 with Firmware Version below 2.1 or Serial Number A-0001 til H-9999) 2300/90.20 2244/90.31 2244/90.45 2300/90.30 2260/90.51 2260/90.80 2245/90.07 2304/103/USA ORDERING NUMBER
24
USA TEL: (1) 631 231-1700 FAX: (1) 631 231-1711 E-MAIL: [email protected] www.narda-sts.us