Industrial Application of Point Cloud STL Data For 2
Industrial Application of Point Cloud STL Data For 2
net/publication/300145726
CITATIONS READS
6 2,492
3 authors:
SEE PROFILE
All content following this page was uploaded by Pushparaj Mani Pathak on 04 May 2016.
Key words: reverse engineering, scanning techniques, point cloud data, STL format
Authors´ data: Kumar, [Atul], Jain, P[ramod] K[umar]; Pathak, P[ushparaj] M[ani],
Mechanical & Industrial Engineering Department, Indian Institute of Technology
Roorkee, India, [email protected],
[email protected],[email protected]
This Publication has to be referred as: Kumar, [Atul]; Jain, P[ramod] K[umar] &
Pathak, P[ushparaj] M[ani] (2012). Industrial Application of Point Cloud / STL Data for
Reverse Engineering, Chapter 38 in DAAAM International Scientific Book 2012, pp.
445-462, B. Katalinic (Ed.), Published by DAAAM International, ISBN 978-3-901509-
86-5, ISSN 1726-9687, Vienna, Austria
DOI:10.2507/daaam.scibook.2012.38
445
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
1. Introduction
446
DAAAM INTERNATIONAL SCIENTIFIC BOOK 2012 pp. 445-462 CHAPTER 38
2. Reverse Engineering Methodology
Data Acquisition
(Contact or Non-Contact methods)
Preprocessing
(Noise Filtering & Merging)
Feature Extraction
CAD Model
CAD/CAM/CAE Analysis
447
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
preparation is frequently described as preprocessing. In digitization system, surface
reconstruction methods and pre-processing phase can entail different processes. For
the pre-processing the steps involved are: noise filtering, data smoothing and data
reduction. The segmentation process splits a triangular mesh into sub-meshes to
which an appropriate single surface can be fitted, and it seriously affects the quality
of the resulting CAD model. To improve the quality of segmentation, it is essential to
make the use of features (sharp edges and symmetry planes) extracted in the fourth
step. Among various features, few features are very important for the segmentation
process because of them, some feature properties are directly appled in industrial
products. A concept with redesign and prototyping of free-form surfaces in the
manufacturing industry often involves. The application of physical models for initial
conceptual and aesthetic design, product prototyping, and performance testing and
model modification are needed for obtained an optimal product design. Computer-
Aided Design (CAD) is the use of computer technology to assist in the design
particularly in technical drawing and engineering drawing of an object. CAD is
mainly using for detailed engineering of 3D models and 2D drawings of physical
components, but it is also used through out the reverse engineering process from 3D
models and 2D drawings of physical components which do not have available
technical drawing and engineering drawing (Tai & Hung, 2000 ; Hussain et al.,
2008). In contrast to the tradinatioal production sequence after dizitigation the
existing objects, a solid model or surface model can be deduced in order to make use
CAD/CAM/CAE technologies to full fill the modren industry demand.
Reverse Rapid
Engineering Prototyping
Rapid prototyping provides the mean to reduce the lead time required to
produce a physical prototype of an object. Rapid prototype technique build the
model, one layer at a time, from bottom to top. While most traditional manufacturing
techniques use subtractive or formative processes. The additive nature provides
cohesiveness with the data types created by reverse engineering systems. Once the
data has been successfully acquired by the reverse engineering system, limitless
design and alternatives are achieved through modification or scaling of the newly-
acquired CAD data which can be further used to produce physical prototypes to
448
DAAAM INTERNATIONAL SCIENTIFIC BOOK 2012 pp. 445-462 CHAPTER 38
achieve manufacturing objectives. The practical integration of contact and non-
contact reverse engineering and rapid prototyping techniques is becoming more and
more prevalent each year. The related fields are engineering, automotive, medical,
aerospace, entertainment, electronics, and consumer goods and take advantage of
easily integrated technologies to develop creative solutions of design problems.
449
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
Industrial Inspection: When a part is compared with its existing CAD model, a
reverse engineering system can acquire the actual map of the part surface, and
deviations, if any, can be identified.
Design of Large Items: Precise measurements of large parts are often not
possible with traditional metrological equipment. Reverse engineering-based
part image reconstruction systems can help by mapping the part surface in the
form of CAD model. This CAD model can now be scaled and modified as
needed.
Worn or Broken Parts: When a part breaks or worn and the engineering
drawing is no longer available, part image reconstruction systems can be used
to create the CAD model. The CAD model can now be used to manufacture the
clone of the worn or broken part.
Fig. 4. The sequence of steps requierd for the application of reverse engineeirng
2.4 Advantages and Limitations in Reverse Engineering
The modern automotive industry reverse engineering is frequently use over
other manufacturing techniques. The main and foremost advantages of reverse
engineering are fast availability of CAD models and physical model is used as the
starting point, shortened development process, fully developed product at the start of
production and reduction in product and production costs. To complete the reverse
engineering process the better methods are needed for deciding quality of sensor.
Open problems remain in freeform surfaces combining with manufacturing features,
particularly with regards to segmentation and surface blending.
450
DAAAM INTERNATIONAL SCIENTIFIC BOOK 2012 pp. 445-462 CHAPTER 38
3. Previous Research
During the last decade, number of reverse engineering methodologies has been
developed. In 21 century, these methodologies have been change rapidly due to
gradually changing in technologies. When refine to technology, it become simple and
ease that be directly related to fast and accurate. In this section a brief review of the
state-of-the-art in reverse engineering in general definition, methodology, digitization
technique, point cloud data, STL, noise reduction, CAD model, surfaces creation,
geometry error analysis, estimate the out portion, curve patches and FEM analysis.
Raja & Fernandes (2008) define the engineering as, the process of designing,
manufacturing, assembling, and maintaining products and systems. There are two
types of engineering, forward engineering and reverse engineering. Forward
engineering is the traditional process of moving from high-level abstractions and
logical designs to the physical implementation of a system. The process of
duplicating an existing part, subassembly, or product, without drawings,
documentation, or a computer model is known as reverse engineering. Tong et al.
(2008) explained that reverse engineering is a digital technique developed for setting
3D CAD models from physical objects, which is an effective method for measuring
complex surfaces. The output of this phase is geometric model in one of the
proprietary formats such as point cloud, IGES, VDA, STL, DXF, OBJ, VRML, ISO
G Code, etc. Bopaya & Hosni (1994) defined the objective of any reverse engineering
approach is to generate a 3-D mapping of the product in a CAD file format. In order
to do this, the x, y, z coordinates of multiple points on the product surface. These
coordinates can be used to develop the drawing of product further for redesign or
CAD/CAM packages. Durupt et al. (2010) focused on reverse engineering in
mechanical design and proposed the Knowledge Based Reverse Engineering
methodology, which allow managing and fitting manufacturing and functional
features. Zhoul et al. (2008) introduced the imaging measurement system for rubbing
parts. The rubbing part model was constructed based on an Amsler friction and wear
test machine. Image process technology was applied to characterize the images of
adhesive wear and abrasive wear. Wear images were first enhanced by median
filtering method then a reiterative algorithm was used to compute the segmenting
thresholds. Gao et al. (2006) proposed a defects-free model-based repair strategy to
generate correct tool paths for build up process and machining process adaptive to
each worn component through the reverse engineering application. Based on 3D
scanning data, a polygonal modeling approach is introduced to rapidly restore worn
out parts use for welding, machining and inspection processes. Bagci (2009)
discussed about obtaining the CAD data from damaged three different parts to
reproduce or make a redesign for component, whose technical drawings is not
available. The CAD models can be recovered, reconstructed and considering with
parametric and geometric continuity. These evils have been solved by referring to
some practical approaches and establishing continuity across curve and surface
patches for free form surface modeling. Tsakatikas & Kaisarlis (2007) presented an
investigation of the criticality analysis applied for the classification of industrial spare
parts, in conjunction with the implementation of reverse engineering techniques.
451
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
Based on for prioritizing, the need for re-engineering components for maintenance
purposes and the equipment criticality are use for an adapted failure mode effects and
criticality analysis technique based on the operation and failures history record.
Gadelmawla (2011) had utilized the computer vision technology to develop a non-
contact and rapid measurement system for measuring and inspecting most of spur
gear parameters with an appropriate accuracy. A vision system has been established
and used to capture images for gears to be measured or inspected processes using
Microsoft Visual. Tut et al. (2010) presented some aspects about design using
CAD/CAM/FEA programs with rapid prototyping, scanning and measuring
machining and its integration in industrial field. A new gasket for a ball screw used in
a bending tube machine was produced by rapid prototyping techniques starting from
a broken one. First the broken gasket was scanned by scanning machine obtaining the
primary 3D model which is imported to CAD/CAM programs and the final product is
achieved on milling machine. The gasket mechanical characteristics were
investigated by finite element analysis. After FEA simulation, a new material was
chosen in order to increase the mechanical characteristics and also improves the tool,
wear, life, scuff resistance and handling characteristic. A safety stock of the thus
defined critical components is of paramount importance and must be readily
available. In order to achieve new material properties, especially in the case of
mechanical equipments are considering obsolete, remanufacturing through reverse
engineering techniques. It must be considered one of the most important reverse
engineering tasks is the assignment of the dimensional and geometrical accuracy
specifications of the reverse engineered components that are directly connected with
manufacturing cost and time. Today the automotive manufacturing industries with
reverse engineering produce the fully developed product at the start of production so
they can be reduce the cost of product and production.
452
DAAAM INTERNATIONAL SCIENTIFIC BOOK 2012 pp. 445-462 CHAPTER 38
Analogue Sensing
CMM-CNC
with scanning
Machines
Probes
Contact
Point-to-Point
Sensing with Touch CMM-Articulated
Trigger Probes
Reverse CT
Digitization
Engine e ring Transmissive
MRI
Shape From
Sonar Shading
Non
Non Optical
Contact
Shape From
Microwave
Stereo
Radar
Shape From
Motion
Optical
Triangulation
Structured
Active Light
Moire Effect
Time of Flight
Coherent
Laser Radar
Fig. 5. Classifications of data acquisition techniques used in contact and non contact
approches for Revere Engineeirng technique
453
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
tactile method cannot measure the parts made of soft materials and have relatively
lower scanning speed compared to non-contact techniques. Non-contact methods use
light, sound or magnetic fields to acquire shape from objects. In the case of contact
and non-contact, an appropriate analysis must be performed to determine the
positions of the points on the objects surface.
Optical methods of shape capture are probably the broadest and growing in
popularity over contact methods. There are five important categories of optical
methods: laser triangulation, time-of-flight, interferometers, structured lighting and
stereo analysis. Active methods are distinguished from passive methods in that
artificial light is used in the acquisition of data. This is because they have relatively
fast acquisition rates. Correlation of image pairs and landmarks within the images are
big difficulties with this method and because of that active methods are preferred.
Laser Triangulation is a method, which uses location and angles between light
sources and photo sensing devices to deduce position. A high-energy light source is
focused and projected at a pre-specified angle at the surface of interest. A
photosensitive device, usually a video camera, senses the reflection of the surface and
then by using geometric triangulation from the known angle and distances.
Triangulation can acquire data at very fast rates. The accuracy is determined by the
resolution of the photosensitive device and the distance between the surface and the
scanner. Moss et al. (1989) present a detailed discussion of a classic laser
triangulation system used to capture shape data from facial surfaces. The use of laser
triangulation on a coordinate measuring machine is presented by Modjarred (1998).
These references give a broad survey of methods, approaches and limitations of
triangulation. Measuring distance by sensing time-of-flight of the light beams emitted
is the way a ranging system works. Practical methods are usually based on lasers and
pulsating beams. Jarvis (1983) presents an in-depth article on time-of- flight range
finders giving detailed results and analysis. Structured lighting involves projecting
patterns of light upon a surface of interest and capturing an image of the resulting
pattern as reflected by the surface. The image must then be analyzed to determine
coordinates of data points on the surface. A popular method of structured lighting is
shadow Moire, where an interference pattern is projected onto a surface producing
lighted contour lines. These contour lines are captured in an image and are analyze to
determine distances between the lines. The final optical shape capture method of
interest is stereo image analysis. This is similar to structured lighting methods in that
frames are analyzed to determine coordinate data. This method is often referred to as
a passive method since no structured lighting is used. One more data acquisition
methods will examine as an acoustic, where sound is reflected from a surface,
magnetic, where a magnetic field touches the surface and a hybrid of both contact and
non-contact. Sonar is used extensively for decades for distance measuring. In
mentioned contest, the reverse engineering with contact or non-contact digitization
technique are absolutely necessary because allow capturing and digitization the 3D
object geometry to be utilized in generating line, curve, surfaces, CAD/CAM/CAE
techniques, tool path generation etc. Therefore, reverse engineering is generated the
numerical simulation of the process and product optimization to increases the final
product quality using captured and digitized 3D object geometry.
454
DAAAM INTERNATIONAL SCIENTIFIC BOOK 2012 pp. 445-462 CHAPTER 38
4.3 Hybrid Techniques Acquisition Techniques
Hybrid modeling systems are a combination of contact and non-contact
systems or NC coding and laser scanning techniques (Clark 2000). The first type of
hybrid is usually consists of the coordinate measuring machine and integrated laser
based technology. The technique focuses on modeling complex and free-form shapes
of mechanical objects by comparing contact and non-contact methods for digitizing
the surface. During hybrid scanning the effects of ambient lighting are discussed for
non-contact systems. Whether or not the system can measure the ambient lighting
depends on the projected color of light on the object. If a system projects laser light
then the unwanted frequencies can be filtered out. If the system projects white light,
then no particular frequencies can be blocked out. This is because it might be
carrying the information required to measure the object. Therefore, white light area
based systems will be limited in their ability to measure ambient lighting verses laser
based systems.
455
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
Noise and incomplete data: Noise elimination in data samples is a difficult
issue. Noise can be introduced in a multitude of ways, from extraneous
vibrations, specular reflections, etc. There are many different filtering
approaches and tools that can be used for eliminate the scanned noise. An
important issue is whether to eliminate the noise before, after, or during the
model building stage.
Statistical distributions of parts: A similar problem is restoration of missing
data. It is partly necessary due to the above-mentioned inaccessibility and
occlusion problems. Moreover, the nature of optical and even tactile scanning,
the data close to sharp edges is also fairly unreliable. So, there are situations
where only parts of a certain surface can be measured. There are missing parts
or parts obscured by other elements, but to reconstruct the whole surface from
just the visible parts.
Statistical distributions of parts: Statistical distribution of parts deals with the
fact that any given part, which is scanned, only represents one sample in a
distributed population. When reverse engineering methods attempt to
reproduce a given shape, the tolerance distribution of the scanned part must be
considered.
Surface finish: The final issue is surface finish of the part being measured.
Smoothness and material coatings can dramatically affect the data acquisition
process. Tactile or optical methods will produce more noise with a rough
surface than a smooth one. Reflective coatings also can affect optical methods.
In summary, while systems exist it can perform the simple operation of 3D copying.
The goal of extracting higher level information is to be edited and analyzed the data
of copying object. Key research areas which still need further work before general-
purpose reverse engineering becomes widely available include: improving data
capture and calibration, coping with noise, reliable segmentation, fair surface fitting,
recognizing natural structure of the geometry of the object, and finally in this chapter
all above steps are discussing with a appropriate problem.
5. The Present Work-Reverse Engineering for Wear Estimation of Complex
Geometry Part
The present work purpose a technique to identify the wear out portion on spur
gear teeth by reverse engineering approach. Spur gear is selected for the study as it is
an imperative element in mechanical industries to transmit motion and power
between two parallel shafts. During motion and power transfer it worn out with time
due to rubbing of meshed gears. Wear may also be caused by foreign element like
dust particle, metal debris, etc. Over the span of time, meshed gears geometry of teeth
varies continuously and hence, an actual CAD spur gear model is different from its
corresponding tattered one. As a result, it can be used to determine whether the
service life of gear was over or not. In this study, the spur gear has been scanned
before and after the wear using a PICZA 3D laser scanner (Roland LPX60). The
scanned data obtained in the form of point cloud or STL data has been used to create
456
DAAAM INTERNATIONAL SCIENTIFIC BOOK 2012 pp. 445-462 CHAPTER 38
the surface geometry of spur gear teeth before and after the wear to determine total
area of the wear out portion.
5.3 Preprocessing
A modern 3D digitization system such as 3D laser scanner generated the large
amount of point cloud as shown in Figure 6. Therefore, before the surface
reconstruction process it is necessary to prepare the noise free point cloud data. This
preparation is frequently described as preprocessing. In this work, the 3D editor
(version 2.0) tool of Dr. PICZA3 has been used for editing the data and for removing
the noise in surface models and noise free data can be saved as point cloud and STL
data. The preprocessed image of spur gear is shown in Figure 7.
Fig.6. Point cloud data of spur gear Fig.7. Gear profile after preprocessing
457
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
after wear in three teeth of the gear marked as A, B and C. By comparing
Figure 8 (a) and (b) one can estimate the amount of wear at the various gear
teeth. For mathematical computation, the gear tooth profiles of tooth B both
before and after wear are presented in figure 9 (a).
II. Using STL data: The surface model of the spur gear before and after wear has
been created on the Pro/E modeling software. The collected data is converted
into surface model. The generated teeth profile has been made such that it best
fits with the original teeth profile as shown on figure 8 (d). The generated STL
file is imported in Pro/E modeling software by using Insert / shared data /
from file / STL. In this way the surface profile of the scanned gear is recreated
shown in figure 8 (c). The generated surface model is used for downstream
operation on any modeling software such as inspection, compression, analysis,
mass properties etc.
50
50
40
40
30
30
20
20
10
10
C
Y (mm)
0
Y (mm)
-10
-10
-20 -20 B
-30 -30 A
-40 -40
-50 -50
-50 -40 -30 -20 -10 0 10 20 30 40 50 -50 -40 -30 -20 -10 0 10 20 30 40 50
X (mm) X (mm)
Worn Out
Tooth
458
DAAAM INTERNATIONAL SCIENTIFIC BOOK 2012 pp. 445-462 CHAPTER 38
5.5 Tooth Profile Comparison
The tooth profile accuracy also depends on the placement of the gear on the
table before and after wear. Hence data is analyzed to extract the point cloud data for
different values of z (z = 0, 1, 2…14). Some minor error may occur during the profile
comparison because of scanning process variables like change in voltage,
misplacement of gear and variation in rpm while table rotation. The wear out area has
been indicated for point cloud data in figure 9 (a) and STL data in figure 9 (b).
-6
-8
Before Wear Tooth Profile
-10
-12
-14
-16
Y (mm)
-24
-26
-40 -38 -36 -34 -32 -30 -28 -26 -24 -22 -20
X (mm)
Where,
ni = Number of full square grid
Ai = Area of full square grid
nj = Number of half square grid
Aj = Area of half square grid
The surface CAD model is created using Pro/E modeling software after the
processing. The surface fitting operation is carried out for original and worn out gear
tooth profile .The wear out area can be measured for all specific value of z (0 to
14mm) by comparing the both tooth profiles before and after wear using Pro/E
modeling software. The wear out area of tooth has been evaluated at z = 0.0 mm to
459
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
14.0 mm and calculated value is 286.944×10-2 (mm2) as shown in table 1. The area is
calculated with the help of 14 number of datum planes for individual values of z
using.
6. Conclusion
460
DAAAM INTERNATIONAL SCIENTIFIC BOOK 2012 pp. 445-462 CHAPTER 38
demand satisfaction the staics and daynamic study of worn out object can be carried
out using CAD/CAE techniques.
7. References
461
Kumar, A.; Jain, P. K. & Pathak, P. M.: Industrial Application of Point Cloud / ST…
Lee, K. H.; Woo, H. & Suk, T. (2001). Data Reduction Methods for Reverse
Engineering, The International Journal of Advanced Manufacturing
Technology, Vol. 17, No. 10, (2001), pp735-743
Liang, Chia, Chen, & Grier, Lin, C.I. (2000). Reverse engineering in the design of
turbine blades a case study – a case study in appliying the MAMDP, Robotics
and Coputer Integated Manufacturing, Vol. 16, (2000), pp 161-167
Modjarred, A. (1988) Non-Contact Measurement Using a Laser Scanning Probe,
Proceedings of the SPIE, pp 229-239, In-Process Optical Measurements, Vol.
1012, (1988)
Moss, J. P.; Linney A. D., Grindrod, S. R., & Mosse, C. A. (1989). A Laser
Scanning System for the Measurement of Facial Surface Morphology, Journal
of Optics and Lasers in Engineering, Vol. 10, (1989), pp 179-190
Raja, V. & Fernandes, K. J. (2008). Reverse Engineering an Industrial Perspective,
Springer Series in Advanced Manufacturing, ISBN 978-1-84628-856-2
Sahoo, K. C. & Menq C. H. (1991). Localization of 3-D Objects Having Complex
Sculptured Surfaces Using Tactile Sensing and Surface Description, Journal of
Engineering for Industry, Vol. 113, (1991), pp 85-92
Sokovic, M. & Kopac, J. (2006). RE (reverse engineering) as necessary phase by
rapid product development, Journal of Materials Processing Technology, Vol.
175, (2006), pp 398–403
Tai, C. C. and Huang, M. C.(2000). The Processing of Data Points Basing on Design
Intent In Reverse Engineering, International Journal of Machine Tools and
Manufacture, Vol. 40, (2000), pp 1913–1927
Tsakatikas & Kaisarlis G. (2007). Reverse Engineering In Industrial Maintenance
Component Criticality Analysis, 4th International Conference on NDT, (2007),
Chania, Crete-Greece
Tut, V.; Tulcan, A., Cosma, C. & Serban, I. (2010). Application of CAD/CAM/FEA,
Reverse Engineering and Rapid Prototyping in Manufacturing Industry,
International Journal of Mechanics, Vol. 4, No. 4, (2010), pp 79-86
Varady; Tamas, Martin, Ralph R. & Coxt, Jordan (1997). Reverse engineering of
geometric models-an introduction, International Journal of Computer-Aided
Design. Vol. 29, No 4, (1997), pp 255-268
Woo, H.; Kang E., Wang, S. & Lee, K. H., (2002). A New Segmentation Method For
Point Cloud Data. International Journal of Machine Tools and Manufacture,
Vol. 42, (2002), pp 167-178
Xiong, Y. L. (1990). Computer Aided Measurement of Profile Error of Complex
Surfaces and Curves: Theory and Algorithm, International Journal of Machine
Tools and Manufacturing, Vol. 30, No. 3, (1990), pp 339-357
Yang, W. B.; Chen, M. B. and Yen, Y. N. (2011). An Application of Digital Point
Cloud to Historic Architecture in Digital Archives, International Journal of
Advances in Engineering Software, Vol. 42, (2011), pp 690–699
Zhou1, J.; Zhou, Q., Yang, L. & Wu, G.(2006). Acquisition and rendering of
characteristic images of the wear surfaces of running parts within machinery,
International journal of Advances in Engineering Software, Vol. 37, (2006), pp
592-600
462
View publication stats