Professional Documents
Culture Documents
Centrifugation Separations
Centrifugation Separations
Centrifugation Separations
Centrifugation Separations
Mark Frei
BioFiles v6 n5, 6–7
CENTRIFUGATION TECHNIQUES
There are two types of centrifugal techniques for separating particles: differential centrifugation and
density gradient centrifugation. Density gradient centrifugation can further be divided into rate-
zonal and isopycnic centrifugation.
Differential Centrifugation
Rate-Zonal Centrifugation
Isopycnic Centrifugation
Suitable Density Gradient Medium Selection
DIFFERENTIAL CENTRIFUGATION
The simplest form of separation by centrifugation is differential centrifugation, sometimes called
differential pelleting (Figure 1). Particles of different densities or sizes in a suspension will sediment
at different rates, with the larger and denser particles sedimenting faster. These sedimentation rates
can be increased by using centrifugal force. A suspension of cells subjected to a series of increasing
centrifugal force cycles will yield a series of pellets containing cells of decreasing sedimentation rate.
:
Figure 1. Differential Centrifugation
Particles of different densities or size will sediment at different rates with the largest and most
dense particles sedimenting the fastest followed by less dense and smaller particles.
Differential pelleting is commonly used for harvesting cells or producing crude subcellular fractions
from tissue homogenate. For example, a rat liver homogenate containing nuclei, mitochondria,
lysosomes, and membrane vesicles that is centrifuged at low speed for a short time will pellet mainly
the larger and more dense nuclei. Subsequent centrifugation at a higher centrifugal force will pellet
particles of the next lower order of size (e.g., mitochondria) and so on. It is unusual to use more than
four differential centrifugation cycles for a normal tissue homogenate.
RATE-ZONAL CENTRIFUGATION
In rate-zonal centrifugation the problem of cross-contamination of particles of different
sedimentation rates may be avoided by layering the sample as a narrow zone on top of a density
gradient (Figure 2). In this way the faster sedimenting particles are not contaminated by the slower
particles as occurs in differential centrifugation. However, the narrow load zone limits the volume of
sample (typically 10%) that can be accommodated on the density gradient. The gradient stabilizes
the bands and provides a medium of increasing density and viscosity.
:
Figure 2. Rate-Zonal Centrifugation
Sample is layered as a narrow zone on the top of a density gradient (2B). Under centrifugal force,
particles move at different rates depending on their mass (2C).
The speed at which particles sediment depends primarily on their size and mass instead of density.
As the particles in the band move down through the density medium, zones containing particles of
similar size form as the faster sedimenting particles move ahead of the slower ones. Because the
density of the particles is greater than the density of the gradient, all the particles will eventually
2
form a pellet if centrifuged long enough.
ISOPYCNIC CENTRIFUGATION
In isopycnic separation, also called buoyant or equilibrium separation, particles are separated solely
on the basis of their density. Particle size only affects the rate at which particles move until their
density is the same as the surrounding gradient medium. The density of the gradient medium must
be greater than the density of the particles to be separated. By this method, the particles will never
sediment to the bottom of the tube, no matter how long the centrifugation time (Figure 3).
:
Figure 3. Isopycnic Centrifugation
Starting with a uniform mixture of sample and density gradient (3A) under centrifugal force,
particles move until their density is the same as the surrounding medium (3B).
Upon centrifugation, particles of a specific density sediment until they reach the point where their
density is the same as the gradient media (i.e., the equilibrium position). The gradient is then said to
be isopycnic and the particles are separated according to their buoyancy. Since the density of
biological particles is sensitive to the osmotic pressure of the gradient, isopycnic separation may vary
significantly depending on the gradient medium used. Although a continuous gradient may be more
suited for analytical purposes, preparative techniques commonly use a discontinuous gradient in
which the particles band at the interface between the density gradient layers. This makes harvesting
certain biological particles (e.g., lymphocytes) easier.