Service Manual LCD Monitor Dell 2209WA

Service Manual
Service Manual
LCD Monitor 2209WA
-0-
Downloaded from www.Manualslib.com manuals search engine
1
Service Manual Versions and Revision

No. Version Release Date Revision
1 2.0 2008/10/17 Initial Release
Copyright
Copyright 2007 InnoLux Display. Corp. Ltd
All Rights Reserved
This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any
electronic or machine readable form without prior written permission of Foxconn Tech. Corp. Ltd.
Dell 2209WA Service Manual

Service Manual
Table of Contents
CHAPTER 1- PRECAUTIONS & SAFETY NOTICES ......................................................................................................................
1. SAFETY PRECAUTIONS .....................................................................................................................................................
2. PRODUCT SAFETY NOTICE................................................................................................................................
3. SERVICE NOTES ................................................................................................................................................................
CHAPTER 2- SERVICE TOOLS & EQUIPMENT REQUIRED ................................................................................................
CHAPTER 3- CIRCUIT THEORY .......................................................................................................................................................
1. BLOCK DIAGRAM ................................................................................................................................................................
2. ELECTRONIC CIRCUIT THEORY ................................................................................................................................
3. FACTORY PRESET TIMING TABLE ................................................................................................................................
4. POWER ON/OFF SEQUENCY ...................................................................................................................................................
5. D-SUB CONNECTOR PIN ASSIGNMENT ................................................................................................................................
6. AC OUTLET PIN ASSIGNMENT ................................................................................................................................
7. INNER CONNECTOR PIN ASSIGNMENT ................................................................................................................................
8. KEY PARTS PIN ASSIGNMENTS................................................................................................................................
CHAPTER 4- DISASSEMBLY & ASSEMBLY ................................................................................................................................
1. EXPLODED DIAGRAM ............................................................................................................................................................
2. 2209WA DISASSEMBLY BLOCK................................................................................................................................
3. ASSEMBLY BLOCK ................................................................................................................................................................
CHAPTER 5- TEST AND ADJUSTMENT ................................................................................................................................
1. FUNCTION KEY DEFINITIONS .................................................................................................................................................
2. OSD CONTROL................................................................................................................................................................
3. FACTORY MODE INTRODUCTION ................................................................................................................................
4. BURN-IN PATTERN ................................................................................................................................................................
5. AUTO COLOR BALANCE (AUTOMATICALLY CALIBRATE CHIP ADC PARAMETER BY USING CHIP
INTERNAL DAC.) .................................................................................................................................................................................
6. UPLOAD FIRMWARE TO MCU VIA VGA CABLE .....................................................................................................................
7. AFTER REPAIR, TO ENSURE THE QUALITY YOU SHOULD DO THE FOLLOWING TEST AND
ADJUSTMENT. .......................................................................................................................................................................................
CHAPTER 6- TROUBLE SHOOTING ................................................................................................................................

1. COMMON ACKNOWLEDGE .....................................................................................................................................................
2. NO POWER LED OFF .............................................................................................................................................................
3. POWER NORMAL LED AMBER ................................................................................................................................
4. BACKLIGHT CAN’T BE TURNED ON ................................................................................................................................
5. NO PICTURE BACKLIGHT ON ................................................................................................................................
6. AT 32-GRAY SCALE PATTERN, COLOR LOST IN SOME SCALE ................................................................................................
CHAPTER 7- RECOMMENDED PART LIST ................................................................................................................................
ATTACHMENT 1- BILL OF MATERIAL ................................................................................................................................
ATTACHMENT 2- SCHEMATIC .......................................................................................................................................................
ATTACHMENT 3- PCB LAYOUT ......................................................................................................................................................
2
Service Manual
Chapter 1- PRECAUTIONS & SAFETY NOTICES
SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a user’s
safety comes first. However, improper used or installation may cause
damage to the monitor as well as to the user.
WARNINGS:
l This monitor should be operated only at the correct power sources
indicated on the rating label on the rear cover of the monitor. If you’re
unsure the power supply in your residence, consult your local dealer or
Power Company.
l Use only the specified power cord that comes with this monitor.
l Do not try to repair the monitor by yourself, as it contains no
user-serviceable parts. This monitor should only be repaired by a
qualified technician.
l Do not remove the monitor cabinet. There is high-voltage parts inside
that may cause electric shock to human bodies.
l Stop using the monitor if the cabinet is damaged. Have it checked by a
service technician.
l Put your monitor only in a lean, cool, dry environment. If it gets wet,
unplug the power cable immediately and consult your closed dealer.
l Always unplug the monitor before cleaning it. Clean the cabinet with a
clean, dry cloth. Apply non-ammonia based cleaner onto the cloth, not
directly onto the class screen.
l Do not place heavy objects on the monitor or power cord.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety
visual inspections and the protection afforded by them cannot necessarily be
obtained by using replacement components rated for higher voltage, wattage,
etc. Before replacing any of these components read the parts list in this
manual carefully. The use of substitute replacement parts, which do not have
the same safety characteristics as specified in the parts list, may create shock,
fire, or other hazards.
SERVICE NOTES
l When replacing parts on circuit boards, clamp the solder wires around
terminals before soldering.
l Keep wires away from high voltage, high temperature components and
sharp edges.
l Keep wires in their original position so as to reduce interference.
l Adjustment of this product please refers to the user’ manual.
l Use Pb free solder wire for circuit board preparation.
3
Service Manual
Chapter 2- SERVICE TOOLS & EQUIPMENT REQUIRED
1. SIGNAL GENERATOR
2. MULTIMETER
3. SCREW DRIVER
4. OSCILLOSCOPE
5. Soldering IRON
6. SOLDER (Lead free, RoHS compliance)
7. Color Analyzer
8. Fox_VISP_Programmer
9. Fox_VEDID_Programmer
4
Service Manual
Chapter 3- CIRCUIT THEORY
Block Diagram
Dell 2209WA consists of a main body and a stand (base). The main body
contains a Innolux LCD module with 6 CCFL lamps, There are 4pcs PCBA
in this monitor, one is power & interface & Audio board , one is invert board ,
one is keypad which is OSD control, and one is USB stretch board located
on the right side back cover.. The block diagram is shown as below.
(fig.1)
POWER 24V ON/OFF

circuit
PFC+PWM
controller Feedback
IC SG6901 control
PFC PWM
control control To Inverter
Feedback
+24V DC output 24V ON/OFF Control

to Inverter
CCFL ON/OFF Control
Transfor and
Bulk Main Power Isolate
PFC boost E-CAP PWM circuit Rectifier and Brightness Control
circuit (Main Power filter circuit
transformer)
AUDIO ON/OFF Control
12V DC
regulator and +12V DC output
Rectifier& ON/OFF circuit
Filter Start up
Circuit circuit
PWM
Standby control Transfor and
controller Standby Isolate
Power PWM Rectifier and
IC LD7575 (Standby Power filter circuit
circuit +5V DC output +5V DC output
transformer)
AC Line Filter
GND
+24V /+12V/+5V DC Jack AUDIO Detect

OVP circuit
Feedback
control
AC Input
90V~264V Power saving Power Saving control
circuit
(OPTION)
Contol Signal
From/TO IF Board
5
Service Manual
Inverter
P1 T1 CN1
P2 T2
Brightness Control
ON/OFF Control
P3 T3
+24V
P4 T4
CCFL
P5 T5
P6 T6
Full Bridge
topology
Panel
P7 T7 Inverter IC
OZ9926
P8 T8
P9 T9
To
Feedback
P10 T10 Control
P11 T11
P12 T12
6
Service Manual
Panel Interface
Brightness Control
power parts
Interfac
CCFL ON/OFF Control 5V
e
Panel
5V
Vcc
on/off
LVDS Data
5V USB Vcc
AP1117E33A USB protection
LM1117M-3.3 VCC
power detect
Panel Vcc control
3.3V
24C16
USB out 5V
USB Vcc Control
AP1117E33
LM1117M-3.3
3.3V
AP1117E18
3.3V
LM1117M-1.8
1.8V
USB-Detect USB2.0
Scalar compatible
XTAL
14.318M Hz 4port Hub USB
Data
Audio on/off
TSUMU58EHJ-LF-2
Flash SMSC2514
Audio-det
DCR PWM signal

24V ON/OFF Control
USB Data
USB Data
XTAL
24.M Hz
Connector
VGA
Keypad
DVI
24C02 24C02
PC Hub input 2port USB

DVI Connector VGA Connector connector Device
Fig.1
7
Service Manual
Electronic Circuit Theory

2.1 Inverter PWM circuit
2.1.1)Inverter Control circuit:(fig.2)
4.1
Fig.2
ON/OFF voltage signal coming from IF BD will enable U1 to work.C2 is
used to dump noise.
During the striking period, if the voltage at VSEN_POL(pin12) reaches a
threshold of approximately 2.85V, the transformer output voltage will be
regulated until the striking timer expires.
During normal operation, if the voltage at VSEN_POL(pin12) reaches the
present voltage at OVPT(pin16), the sink and source current of
SSTCMP(pin14) will stop and the TIMER(pin15) will be charged. Once
TIMER(pin15) expires and the abnormal condition still exists, U1 will
shutdown and latch.
Once the IC is enabled, when the voltage at VREF(pin21) rises to
approximately 4.0V, before the transformer output is present, and voltage at
8
Service Manual
pin VSEN_POL(pin12) is greater than approximately 1.5V, the PWM dimming
polarity will be negative. A voltage range of approximately 0.1V to greater than
1.5V to PDIM(pin11) results in minimum and maximum brightness
respectively.
The striking and operating frequency is determined by the external resistor
(R16) and capacitor( C1) connected to Pin8(CT).
LX1, HDR1 and LX2, HDR2 of U1 are used to drive Q1, Q2 and Q3,Q4 .
LX1, HDR1 and LX2, HDR2 are controlled by build-in PWM IC. Q1, Q 2 and
Q3, Q4 are switches that everyone has a build-in IGBTs.
ISEN( pin13)
For lamp “ON” detection, if the peak voltage at ISEN(pin13) is less than
approximately 0.8*ADJ and the voltage at VSEN_POL(pin12) is greater than
the preset voltage at OVPT(pin16), this indicates the lamp has not been
ignited.
During soft-start (lamp striking mode), if the voltage at ISEN(pin13) is
greater than approximately 0.8*ADJ and the voltage at VSEN_POL(pin12) is
less than the preset voltage at OVPT(pin16), this indicates lamp “ON”
condition. The striking period will end and the IC will switch to the normal
operation mode.
Once the IC switches to the normal operation mode, ISEN becomes(pin13)
the feedback signal input pin for the current regulation loop.
ADIM(pin18) Reference voltage for analog dimming
The ADIM is used to deal with the signal of DCR from IF BD. U1 can
adjust the CCFL current automatically based on the DCR signal.
Clamped between 0.52V and 2.45V, ADIM is passed into OZ9926A as
ADJ.
ADJ is the positive input signal to the internal OTA used for current
regulation. Thus, ADJ controls the lamp current amplitude. ADJ also set one of
the lamp “ON” condition, Which is 0.8*ADJ.
2.1.2)Output Circuit and Protection Circuit:(fig.3)
9
Service Manual
Fig.3
The transformer (T1 to T12) secondary winding leakage inductance and
output capacitances that are in the inverter PCB board, forms a lower pass
filter, which converts the square-wave driving signal into a sinusoidal output
voltage signal for CCFL.
The voltage signal sensed through R14 comes to Pin13 of U1-ISEN (Lamp
Current Detection & Control). The CCFL current is detected through R14 and
reaches a regulated value. The CCFL current detected at resistor R13 and
R14 is converted to a voltage level and input to the ISEN pin. Once the voltage
at the ISEN pin reaches the lamp on threshold, the IC switches from the
striking mode to the normal operation mode and the PWM dimming control is
activated.
C21 is used to dump noise. Once the CCFLs are ignited and current is
sensed through resistor R14 ,capacitor C15 performs the loop compensation
function. The voltage at pin1, pin2, pin23 and pin24 controls the drive duty
cycle of the power MOSFETs to regulate the CCFL current.
Q5 off and Q6 on during normal operation. Once any one of ISs falls down,
gate of Q6 lost voltage, Q6 turns off and Q5 turns on, ISEN would be pulled
10
Service Manual
down to 0 voltage. IC shutdown process is triggered
2.2 Power PWM circuit

2.2.1) Block diagram:(fig.4)
11
Service Manual
24V ON/OFF
circuit
PFC+PWM
controller Feedback
IC SG6901 control
PFC PWM
control control To Inverter
Feedback
+24V DC output 24V ON/OFF Control

to Inverter
CCFL ON/OFF Control
Transfor and
Bulk Main Power Isolate
PFC boost E-CAP PWM circuit Rectifier and Brightness Control
circuit (Main Power filter circuit
transformer)
AUDIO ON/OFF Control
12V DC
regulator and +12V DC output
Rectifier& ON/OFF circuit
Filter Start up
Circuit circuit
PWM
Standby control Transfor and
controller Standby Isolate
Power PWM Rectifier and
IC LD7575 (Standby Power filter circuit
circuit +5V DC output +5V DC output
transformer)
AC Line Filter
GND
+24V /+12V/+5V DC Jack AUDIO Detect

OVP circuit
Feedback
control
AC Input
90V~264V Power saving Power Saving control
circuit
(OPTION)
Contol Signal
From/TO IF Board
Fig.4
2.2.2) AC Input and EMI Filter:(fig.5)
Fig.5
CN850 is a connector for connecting AC Power. F850 is a fuse to protect
all the circuit .AC Input voltage is from 90V to 264V. R891, R892, R893 and
R894 are joined between two inputting main circuit to discharge electric
energy to prevent man from shock. L851 and L852 are common mode chock
to filter EMI common mode noise. C850 , C851 and C885,C886 Y-CAP, and
C852 & C853 are X-CAP used for reduce EMI noise.
2.2.3)High Voltage to Low Voltage Control Circuit:(fig.6)
12
Service Manual
D858 1N4007
D859 1N4007
D856 RT851
D850
IN5406
2
GBU8-06 SCK053
L853 L855 L856 D860 L857 L858 FR850

4 - + 1 2 12 1 2 1 2 1VBUS
.6
Bead Bead Bead Bead 0.2R 1W
FR851 600V/8A
0.2R 1W C867 C868 R855 C855 ZD851
C874 2.2nF/1KV 2.2nF/1KV 75K 3W 10nF/400V P6KE350A
3
+ C854
1uF/450V 120u/450V
10
EMI Shield
2
Q853 C882
1 100p/1KV R981 R985
R871 R831 FQPF12N60C 499K 499K D851
R885 1/4W 1/4W FR30-10-LF
1M2 300K 10K
3
R870 1/4W 1/4W
R982 R986
499K 499K
1/4W 1/4W
0.22R/3W 1% R872 R832 R984 R983 1
1M2 300K L859

1/4W 1/4W 499K 499K Bead
C887 C888 R875 1/4W 1/4W
R988 R987
1000p/400V 1000p/400V R873 R833 20
Y1 Y1 1/4W 2
1M2 300K 499K 499K
1/4W 1/4W 1/4W 1/4W
R874 R834 R989

C811 Q850
2
1M2 300K 4700p/50V 15.8K 1%
C812 1uF/50V 1/4W 1/4W SPA11N80C3
1 C881
U850 100p/1KV
SG6901A Signal GND Signal GND
R813
3
R886
1 20 10K
VRMS IAC
68K
Signal GND R814 C818 10uF/25V
2 19
RI VEA R854
24K 1%
C819 100p/50V 0402 Signal GND 20 R853
3 18 1/4W 0.12R 2W
OTP FBPFC
C813 4700p/50V 0402 R822
C814 R821 C817
R816 4 17 46.4K 4700p/50V 24K 1%
IEA OVP
1K 1% 1000p/50V
R817 0402 0402
5 16 VDD
IPFC RANGE Signal GND
2K7 1%
0402 C815 Open 0402
6 15 R858
IMP VDD C822 10K I850
R818 2K7 1% 0402 1uF/50V 4 1
R819 Open 7 14
0402 ISENSE OPFC 3 2
R824 LTV817M
8 13
FBPWM GND
100 1%
C820
4700p/50V
0402 9 12
IPWM OPWM
C821
Signal GND 2200p/50V
0402 10 11
AGND SS
R829 R825
10.5K 1% 200 1% C816
0.01/50V
Signal GND Signal GND

VDD
FR950
VBUS
0.2R 1W
C955
4700p/400V
R837 R838 R839
T900
SPW-129 PQ2620
20K 1/4W 20K 1/4W 20K 1/4W
D951
1 . 7
FR10-10-LF
Q951
R835 D953 MMBT4401 3
VDD 20K 2 3 9
1/4W
Q953 1N4148 8
PMBT2907A C956 + C957 R953
2 3 D952
1
R836
20K 0.01/50V 10u/50V ER104
1/4W 10K 12
+5V_PI 5 11
R940 ZD951 C952 C951 10
1
GDZ20B 20V 47uF/50V 104p/50V

6
.
20K 1% R942 Q950 .
2
0402 R941 2SK3265

6
10K 470 R956

8 5 1
VDD
HV GATE
I952 R943 47R C860
4 1 2200p/400V
3
1K 1% C958
R951 100p/1KV
3 2 U950 10K
7 1
NC RT
LTV817M I950
R958 4 1
LD7575
100K 1%
3 2
R957
GND
2 3 LTV817M
FB SNESE
470R
3
Q860
4
HIGH ON R898 C954 R959

1 C953 0R51 2W
5 PWR24V_ON
10K 0402 RK7002 1000p/50V 470p/50V
2
R897 0402
C897
1uF/10V 1M
0402
Fig.6
D850 is a rectifier in which there are 4 build-in diodes, inverting AC to

DC.
C854 is used to smooth the wave from rectifier. R870 is PFC current
sense Resistor. FR850,FR851,FR950 are fuse resistors to protect the
13
Service Manual
following circuit when inrush current is too large.
U950 (LD7575) is a current-mode PWM controller with excellent
power-saving operation, It features a high-voltage current source to directly
supply the startup current from bulk capacitor and further to provide lossless
startup circuit. Max start-up current for U950 (LD7575) is 100 uA, When
current flow from the bulk capacitor C854 through R835 and R836 gets to HV
pin to start up U950 (LD7575), Meanwhile, the VDD supply current is as low
as 100 uA thus most of the HV current is utilized to change the VDD
capacitor C952, Whenever the VDD voltage is higher than UVLO (16V),the
GATE pin will output signal to drive the power MOSFET(Q950), the
high-voltage current source is off and the supply current is provided from the
auxiliary winding of the transformer PIN5.
When U950 begins to operate Pin5 of U950 (LD7575) will output square
wave to drive Q950, then the main current flow get to GND bypassing
through T850, Q950. Because of the change of current flow, wires in the
other side of T900 will induct current. In the same time, the current inducted
by wires which connected T900 Pin 1 and Pin 3, with components of D952,
Q951, D953, C951 and C952, will be supplied to U950 for normal operating.
The typical current mode PWM controller feedbacks both current signal
and voltage signal to close the control loop and achieve ragulation.U950
detects the Q950 current from Isense pin which max voltage is set as 0.85V,
then the Q950 current can be calculated as: I peak=0.85V/R959,When the
sense voltage across the sense resistor R959, reaches the threshold voltage
over 0.85V, the output GATE drive will be turned off. R957 and C953 is used
to avoid the Isense pin damaged by the negative turn-on spike.
The voltage feedback signal is provided from the TL431 (I951) through the
I950 to the COMP pin. When the voltage on COMP pin is lower than 1.2V,
the IC will turn off.
When Q950 is turned off, the main current flow will be consumed through
D951, C955, R837, R838, and R839, This will prevent Q950 from being
damaged under large current impulse and voltage spike.
RT pin is to program the switching frequency, By connecting R958 to
ground to set the switching frequency, f =(65.0/R958)*100(KHz).
14
Service Manual
When current flow from the Diode D858 and D859 through R871, R872,
R873, R874 and R831, R832,
R833, R834 gets to VRMS and IAC pin to start up U850, Meanwhile, the
VDD supply current is as low as
100 uA thus most of the HV current is utilized to change the VDD capacitor
R858, C822.For normal operation, this input is use to provide current
reference for the multiplier
RI pin is to program the switching frequency, By connecting R814 to
ground to set the switching frequency, f =(1560/R814kohm)
(KHz)=1560/24KHz=65KHz.
PFC output voltage control. For an universal input (90VAC~264VAC)

power supply applying active boost PFC and Fly-back as a second stage, the
output voltage of PFC is usually designed around 250V at low line while it is
380V at high line. This is to improve efficiency for low-line input. In U850
(SG6901A), the RANGE pin is used for the two-level output voltage setting.
The RANGE output is shorted to ground when the Vrms voltage exceeds
1.95V while it is of high impedance whenever the Vrms voltage drops below
1.6V. The output voltage can be designed using below equation .
Range=Open Voutput =〔(R981+R982+R983+R984+R822)/R821〕*3V
Range=Ground Voutput =〔(R981+R982+R983+R984)+(R822// R821)/

(R822// R821)〕*3V
PFC Over-voltage Protection. When the OVP feedback voltage exceeds the
over-voltage threshold, the U850 will inhibit the PFC power converter form
operating abnormally while the FBPFC pin is open.
U850 provides an OTP pin for over-temperature protection. A constant

current is output from this pin. When the OTP voltage drops below 1.2V,
U850 (SG6901A) will be disable. Until OTP voltage exceeds 1.4V.During
startup of PWM stage, the SS pin will charge an external capacitor C816 with
a constant current source.U850 (SG6901A) output stage is a fast totem-pole
gate driver. The output driver is clamped by an internal 18V Zener diode in
order to protect the power MOSFET.
15
Service Manual
As shown in Fig.7, peak-current-mode control is utilized for Flyback PWM.
The U850 (SG6901A) inserts a synchronized 0.5V ramp at the beginning of
each switching cycle. When the IPWM voltage, across the sense resistor,
reaches the threshold voltage, 0.65V or 0.7A selected by RANGE, the
OPWM will be turned off after a small propagation delay Tpd-pwm. When
RANGE is shorted to GND, the PFC output voltage is high and the
corresponding threshold is 0.65V. When RANGE is opened, the PFC output
voltage is low and the corresponding threshold is 0.7V.
When VDD is lower than the turn-off threshold such as 10V, U850
(SG6901A) will be totally shut down. Due to the start up resistor, VDD will be
charged up to the turn-on threshold voltage 12V until U850 is enable again. If
the over loading condition still exists, the protection will take place repeatedly.
This will prevent the power supply from being overheated under loading
condition.
2.2.4)DC_24V ,DC 12V and DC 5V Output Circuit and Feedback circuit:(fig.7)

C858 R856
+24V_DC +24V
1000p/1KV 20 3W L854 F851

D853 CHK BR3X20/2.2uH
1 L860
2 2 1 4A/125V
3
Bead
SRF10-20CT F852
D854 + C862 + C863 + C864 + C865 R865
1 470u/35V 470u/35V 470u/35V 470u/35V 4.7K
T850 2 1W 4A/125V
3
SPW-128 PQ3220
SRF10-20CT C861
10nF/50V
5
. 11
10
. 8
7
A
○
16
Service Manual
+12V
CN853
Q930
AP9972 F853 BNC-2
4 3 1
2
5A/125V
R930 C930 R936
1
100R 3W 1nF/1KV +24V Q931 10K + C932
3
R931 PMBT2907A ZD930 470u/25V R938 L930
2 3 GDZ20B 20V 39.2K + C933
D930 5A/150V 0402 470u/25V
T900 1K
SPW-129 PQ2620 1/4W D932
D931 5A/150V R932 1N4148
2
+ C931
1 . 7 470u/35V NC/CHK-091
20K 1%
C960 R960 0402 R933
3 2200p/100V 10R 2W 10K
9 R937 C935
L953 10K 1nF/50V X7R
8 D960 CHK-077/2.2uH +5V_PI HIGH ON I930
3
1 R935
2 1 Q932 TL431 R939
7 Audio_on_of f
3 10K
12 Audio_on_off 10K 0402 MMBT4401 0402
5 11 SRF10-100CT C964
2
R934
10 D961 C962 C963 C936
6
. 1
2 330uF/16V 330uF/16V 470uF/25V
1000p/50V
0402
1M
0402
. 3 OS-CON SEP OS-CON SEP
SRF10-100CT C961
10nF/50V
C860
2200p/400V R963
R964 +5V_PI +24V_DC +12V
10.5K 1%
330 1% R971 R972 R973

I950 C969 OVP
4 1 +5V_PI OPTION 200 1% 200 1% 200 1%
R968 0.1/50V R976

3 2 2K2 1% 22K 1%
R965 C968 R978 ZD971 ZD972 ZD973
LTV817M Q960 10K 1%
3
RK7002 GDZ5.6B GDZ30A GDZ16A
10K 0.047/50V
I951 1
PWR_sav e 5
Q971
TL431 R962
2
10K 1% C978 R977 C977
(18K/Power 1nF/50V 100K 1% 1nF/50V SFOR3G42
Saving)
R970 C891
1K 1% 0.01/25V
B
○
Fig.7
A
○
D853 and D854 is used to rectify the inducted current. R856 and C858
form the snubber circuit for restrain peak voltage of Schottky Diode D853 and
D854.The parts including C861, C862,C863,C864,C865,R865, and
L853,L860 are used to smooth the current waves that are from D853 and
D854, then 24V voltage is supplied.
DC 24V supply voltage feed back to PWM controller U850 via, R878,
R860,C871, I851,R864,C872,
R863R859, Used to control the voltage feedback loop.
B
○
D930 & D931 is used to rectify the inducted current. R930 and C930 are
used to store energy when current is reversed. The parts including C931,
C932 , Q930,C933 and L930 are used to smooth the current waves that are
from D930 & D931, then 12V voltage is supplied.
DC 12V supply voltage feed back to PWM controller U950 via, R938,
R937, C935, I930, R939,
And Q930 Parts, Used to control the voltage feedback loop.
D960 & D961is a Schottky diode used to rectify the inducted current.C960
and R961 form the snubber circuit for restrain peak voltage of Schottky Diode
17
Service Manual
D960 & D961, The components including C961,C962,C963,L953 and C964
are used to smooth the current waves, then DC+5V voltage is supplied.
DC 5V supply voltage feed back to PWM controller U950 via,
R964,R968,R963,C969,R965,C968 I951,R962 Used to control the voltage
feedback loop.
R970,R971,R972,R973,C891and ZD971,ZD972,ZD973, Q971 form a
combined OVP circuit.
2.2.5) Audio Power output:(fig.8)
+12V
CN853
Q930
AP9972 F853 BNC-2
4 3 1
2
5A/125V
R936
1
+24V Q931 10K + C932
3
R931 PMBT2907A ZD930 470u/25V R938 L930
2 3 GDZ20B 20V 39.2K + C933
0402 470u/25V Audio_DET
1K
1/4W D932
R932 1N4148
1
2
CHK-091
20K 1%
0402 R933
10K
R937 C935
10K 1nF/50V X7R
HIGH ON I930
3
R935
1 Q932 TL431 R939
7 Audio_on_of f
10K
Audio_on_off 10K 0402 MMBT4401 0402
R934
2
C936
1000p/50V 1M
0402 0402
Fig.8
12V audio power is come from linear voltage drop circuit , with output
on/off control circuit.
L930 use for reduce EMI conduct noise. F853 is used for OCP for the LPS test.
2.3 I/F Board Circuit (see the Attachment 2- Schematic)

2.3.1 RGB CAPTURE
- Signal RED,GREEN,BLUE input through CN102 #1,#2,#3, Stop DC via C113,
C114 and C115, and then enter into U105 (TSUMU58EHJ-LF) analog input
PIN #28,#25,#23, and then TSUMU58EHJ-LF deals with signal internally.
D103, D104, D105 are ESD protector to prevent U105 from ESD.
- Signal DDC_SCL (series clock) inputs via CN102#15, and then passes through
ZD106 for ESD protection, goes into EDID EEPROM IC U103 #6.
- Signal DDC_SDA (series data) inputs via CN102#12, and then passes through
ZD103 for ESD protection, goes into EDID EEPROM IC U103 #5.
- Signal TTL vertical sync. (Vsync) inputs via CN102 #14, and then clamped by
ZD105 Zener, passes through R116, and then goes into IC U105
18
Service Manual
(TSUMU58EHJ-LF) #33.
- Signal TTL horizontal sync. (Hsync) inputs via CN101 #13, and then clamped
by ZD104 Zener, passes through R115, and then goes into IC U105
(TSUMU58EHJ-LF) #32.
- CN102#5 is defined as cable detect pin ,the detect pin can create a pull-low
signal send to U105#36pin via R160 to identity cable connection, if plug out
the VGA cable the U105#36pin will receive a high signal and system enter self
test mode when exit factory mode（the device must set at VGA input mode ）.
- U103 is an EEPROM IC which is memory and EDID data saved in it,the IC
power is supplied by PC via CN102#9 with D106 and ZD102 for ESD protection,
or supplied by Monitor self via D106.
2.3.2 DVI CAPTURE

- Differential Signal input RX0+,RX0-,RX1+,RX1-,RX2+,RX2-,RXC+,RXC-
through CN201 #18,#17,#10,#9,#2,#1,#23,#24 via
R206,R205,R204,R203,R202,R201,R208,R207 enter into U105
(TSUMU58EHJ-LF) Digital input terminal #15,#16,#12,#13,#9,#10,#18,#19,
and then TSUMU58EHJ-LF-LF deals with signal internally. D202, D203,
D204, D205, D206, D207, D208, D209 are ESD protector to prevent U105
from ESD
- Signal DDC_SCL (series clock) inputs via CN201#6, and then passes through
ZD204 Zener for ESD protection, via R209, goes into EDID EEPROM IC
U201 #6.
- Signal DDC_SDA (series data) inputs via CN201#7, and then passes through
ZD203 Zener for ESD protection, via R210, goes into EDID EEPROM IC
U201 #5.
- CN201#15 is defined as cable detect pin, the detect pin can create a pull-low
signal send to U105#49pin via R216 to identity cable connection, if plug out
the DVI cable the U105#49pin will receive a high signal and system enter self
test mode when exit factory mode（the device must set at DVI input mode ）.
- U201 is an EEPROM IC which is memory and DVI input EDID data saved in
it ,the U201 power is supplied by PC via CN201#14 through D201, or supplied
by Monitor self via D201..
2.3.3 Buttons Control
- Button “Power” on right corner of front bezel connects to U105
(TSUMU58EHJ-LF ) #4 through CN104 #8 and R125, U105 #4 is defined as
power on/off.
- Button “+” on right corner of front bezel connects to U105
(TSUMU58EHJ-LF) #120 through CN104 #2and R154, U105#120 is defined
as “Plus”.
- Button “-” on right corner of front bezel connects to U105 (TSUMU58EHJ-LF)
#121 through CN104 #3 and R155, U105 #121 is defined as “Minus”.
- Button “Menu” on right corner of front bezel connects to U105
(TSUMU58EHJ-LF) #50 through CN104 #1and R153, U105 #50 is defined as
“Menu”.
- Button “SELECT” on right corner of front bezel connects to U105
(TSUMU58EHJ-LF) #122 through CN104 #4, U105 #122 is defined as
“SELECT”.
19
Service Manual
- LED Indicator on Front Bezel
a. When press button “power”, U105 (TSUMU58EHJ-LF) #123 be send in low
Voltage, make Q107#3 sends out high Voltage to CN104#5 , and then to
keypad, LED blue on.
b. When in “Suspend” mode, U105 (TSUMU58EHJ-LF) #124 sends out a low
Voltage, make Q108#3 sends out high Voltage to CN104#7 , and then to
keypad, LED Amber on.
2.3.4 MAIN CHIP U105 (TSUMU58EHJ-LF)
- U105 (TSUMU58EHJ-LF ) #86~#77 output 8 bit even and #100~#91 output 8
bit odd LVDS digital data to panel control circuit through CN103.
- U105 (TSUMU58EHJ-LF ) #50 output ”H” potential to make Q104
conducted, and then make Q101 conducted, +5V flow to CN103#1~#3 as
Panel Vdd .
- U105 (TSUMU58EHJ-LF) #109 output CCFL_ON/OFF ”H” potential to
control Inverter on/off.
- U105 (TSUMU58EHJ-LF) #110 output ”H” potential to control Inverter
power on/off.
- U105 (TSUMU58EHJ-LF) #125 outputs Brightness “PWM” signals to control
CCFL brightness.
- TCLK by Crystal 14.318MHz input to U105 (TSUMU58EHJ-LF) #128.
- U105(TSUMU58EHJ-LF) #108 is RESET signals input pin
Please refer to TSUMU58EHJ-LF Pin Assignments table in page

2.3.5 Regulator Circuit
- +5V is from switching power supply .
- +3.3V is generated from Regulator U101 which is supplied by+5V via R101
and through C101 filtering, C102 and C105 is 3.3V which supplies toU102、
U106、U103、U201、U105、U108output filtering.
- +1.8V is generated from Regulator U102 which is supplied byU101-3.3V
through C106 filtering.TheU102 output1.8V via FB105 send to U105.
3. FACTORY PRESET TIMING TABLE

Standard Resolution Horizontal Vertical
Frequency (KHz) Frequency (Hz)
640 x 480 31.469 59.940
640 x 480 37.500 75.000
800 x 600 37.879 60.317
800 x 600 46.875 75.000
1024 x 768 48.363 60.004
VESA
1024 x 768 60.023 75.029
1152x864 67.500 75.000
1280x1024 48.483 60.042
1280x1024 60.087 75.034
1680x1050 55.935 59.887
20
Service Manual
IBM DOS 720 x 400 31.469 70.087
4. Power On/Off Sequency

Hardware power On/Off
When power cord plug into AC socket, Power provides DC_5V to interface board.
DC_5V is main voltage for panel and Regulator U101.
DC_3.3V is coming from Regulator U101, DC_3.3v is main voltage for U105.
When DC_3.3V input to U105 and U105 reset circuit active, U105 all registers
will be set to default, that means finish hardware power on.
When pull out power cord from AC socket,the system shut down instantly for no
supply
Software power On/Off

- When press power key, U105 #4 receives low pulse, then
U105(TSUMU58EHJ-LF) will be wake up and send control signals(at
109,50pin) to on CCFL and switch 5.0v to panel module, at the same time,U105
make the VGA/DVI cable input signal source display normal on panel if the
VGA/DVI cable input signal is active
- If power ON, U105 #123 (LED_blue) will send out low potential, and then LED
blue on.
- If power saveing, U105 #124 (LED_Amber) will send out low potential, and
then LED Amber on.
- If power ON or power saveing, when press power key, U105 #4 receives low
pulse, then U105 will be sleeping and turn off backlight, at the same time, the
panel will lose +5V.
The Panel_Vcc, Backlight_En, CLK/DATA output to panel will follow the following
sequency.
21
Service Manual
Power supply for panel+5V VDD

90% 90%
10%
0V 10%
T1 T2
T5 T6 T7
Signals Valid data

(Digital RGB, HS, VS, DE, CLOCK)
0V
T3 T4
Power supply for backlight
T1(ms) T2 (ms) T3 (ms) T4 (ms) T5 (ms) T6 (ms) T7(ms)

SPEC(LGD) 0.3~10 0.0~50 >500 >100 0.0~50 NA >1000
5. D-SUB Connector Pin Assignment
Pin Symbol Pin Symbol Pin Symbol

1 Red 6 Red_GND 11 GND
2 Green 7 Green_GND 12 DDC_SDA
3 Blue 8 Blue_GND 13 Hsync
4 GND 9 PC+5V 14 Vsync
5 Cable Detect 10 GND 15 DDC_SCL
6. AC Outlet Pin Assignment

2
Pin Symbol Description

1 3 1 Line
2 GND
CN850 3 Neutral
7. Inner Connector Pin Assignment

7.1 CN103 (Connect interface board to Panel,)
1 Panel_Vcc Panel power supply (typ.5.0V)
2 Panel_Vcc Panel power supply (typ. 5.0V)
3 Panel_Vcc Panel power supply (typ. 5.0V)
22
Service Manual
4 NC
5 NC
6 NC
7 GND_LVDS LVDS Ground
8 RXE3+ LVDS signal of even channel 3(-)
9 RXE3- LVDS signal of even channel 3(+)
10 RXEC+ LVDS signal of even channel clock (+)
11 RXEC- LVDS signal of even channel clock (-)
12 RXE2+ LVDS signal of even channel 2(+)
13 RXE2- LVDS signal of even channel 2(-)
15 RXE1+ LVDS signal of even channel 1(+)
16 RXE1- LVDS signal of even channel 1(-)
18 RXE0+ LVDS signal of odd channel 0(+)
19 RXE0- LVDS signal of odd channel 0(-)
20 RXO3+ LVDS signal of odd channel 3(+)
21 RXO3- LVDS signal of odd channel 3(-)
22 RXOC+ LVDS signal of even channel clock (+)
23 RXOC- LVDS signal of even channel clock (-)
25 RXO2+ LVDS signal of even channel 2(+)
26 RXO2- LVDS signal of even channel 2(-)
27 RXO1+ LVDS signal of even channel 1(+)
28 RXO1- LVDS signal of even channel 1(-)
29 RXO0+ LVDS signal of odd channel 0(+)
30 RXO0- LVDS signal of odd channel 0(-)
7.2 CN1, CN2 (Connect to Panel Backlight,)

1 HV High voltage for lamp
2 LV Low voltage for lamp
7.3 CN104 (Connect to keypad, WAFER2*4P or compatible connector)

1 MENU OSD “MENU” control
2 PLUS OSD “PLUS” control and
“Brightness”adjustable hot key
3 MINUS OSD “MINUS” control
4 ENTER OSD “ENTER/SELECT” control
5 LED_blue LED blue on/off control
6 GND Ground
7 LED_Amber LED amber on/off control
8 POWER OSD “POWER” control
23
Service Manual
8. Key Parts Pin Assignments
8.1 U105(TSUMU58EHJ-LF)
24
Service Manual
25
Service Manual
26
Service Manual
8.2 U108 (Serial Flash)

Pin Symbol I/O Description
1 CE# I The device is enabled by a high to low transition
on CE#. CE#
must remain low for the duration of any command
sequence.
2 SO I/O To transfer commands, addresses, or data serially
into the device.
3 WP# I/O The write protect (WP#) pin is used to
enable/disable BPL bit in
the status register.
4 VSS G Connect ground
27
Service Manual
5 SI I/O To transfer commands, addresses, or data serially
into the device
input are latched on the rising edge of the serial
clock.
6 SCK I/O To provide the timing of serial interface.
Commands, addresses, or input data are latched on
the rising edge of the clock input, while output
data is shifted out on the
Falling edge of the clock input.
7 HOLD I/O To temporarily stop serial communication with SPI
flash memory without resetting the device.
8 VDD P To provide power supply.
28
Service Manual
8.3 U950 (LD7575, stand by Power Controller )
1 RT This pin is to program the switching
frequency
I Voltage feedback pin,By connecting a
2 COMP photo-coupler to close the control loop
and achieve the regulation
3 CS I Current sence pin
4 GND
O PWM output ,Gate drive output to drive
5 OUT
the external MOSFET
6 VCC I Power supply
7 NC Unconnected pin
8 HV I PWM output
8.4 U1 ( INL836, CCFL Inverter controller IC)
1 SST_CMP I Enable, soft start time and
compensation of current error amplifier
2 RT I Timing capacitor to set operating
frequency
3 GNDA Ground
4 DRV2 O N MOSFET Driver output
5 DRV1 O N MOSFET Driver output
6 VDDA I Supply voltage input
7 VSEN_DIM I Voltage sense, input analog signal for
PWM driving control
8 ISEN I Lamp current detection & control
8.5 U850 (SG6901 Main Power controller IC)
29
Service Manual
30
Service Manual
Chapter 4- Disassembly & Assembly
1. Exploded Diagram
31
1 2 3 4 5 6 7 8
MODI FY HI STORY
2 ZONE REV DESCRI PTI ON DATE APPROVED
A A
12
16
3
Service Manual
4 13
15

1 14
17 6 9
7
B B
C C
32
8 G
10
11 5
D D
18
B D
E
A
F C
NO. Desi gnat i on I dent i f i cat i on NO. Q' t Remar k NO. Desi gnat i on I dent i f i cat i on NO. Q' t Remar k
ASSY, FRONT, BEZEL, LP2236, Bl ack714030020200R 4- b 502090313401R 1
1
FRONT, BEZEL, LP2236, Bl ack 501010221100R 1 4- c 502120400300R 2
SUB- BUTTON, LP2236, BLACK 750020200600R 1 I NVERT- CHASSI S, LP2236 502090313404R 1
POWER BUTTON LENS, LP2236, DARK SMOKED 501120109500R 1 USB- COVER, LP2236 502090313403R 1
E LOGO Pl at e DELL UX383 LE1963 501110200400R 4 TOP- CHASSI S- MYLAR, LP2236 505040209901R 1
E
BTM- CHASSI S- MYLAR, LP2236 505040209900R 1
ASSY BACK COVER , LP2236, SI LVER 714050019001R 1 SPACER SUPPORT H4. 0 512004001200R 1
SUB- BACK COVER , LP2236, Bl ack 750030200500R 1 RUBBER FOR I NVERT, LP2236 503010006300R 1
Mi d Fr ame, LP2236, Si l ver 501010221102R TAPE ACE W28mmXL15mm 506381001710R 3

1
r el ease- but t on, LE22F4 501030210502R 1 506250024300R 3
LABEL, CARD, LP1931
KENSI NGTON LOCK LE1963 502210100400R 714020016000R 1
1 ASSY STAND , LP2236
SCREW, I , CROSS, T. T- 3*5, ZN- Cc 509012305000R 14 LCD PANEL 22" W 1
4
BACK COVER LOGO, LP2236, Si l ver 501110201100R 1 15 AI O I nt er f ace boar d 1
ASSY CHASSI S- TOP, LP2236 701000011201R 1 16 LVDS 1
CHASSI S- TOP, LP2236 502090313402R 1 17
REMARK
USB - boar d 1
f i x- pl at e- l ef t , LE19E6 502020306000R 1 18 i nver t - boar d 1
F f i x- pl at e- r i ght , LE19E6 502020306010R 1 Scr ew, F, Cr oss, T. T- 2*3, BLK 509212103500R 4 LP2236 Expl oded Dr awi ng F
sl i de, LE22F4 502040500100R 1 Scr ew, P, Cr oss, W/ WAS( 7. 8) , M3*6, Zn- Cc 509146306202R 18
SCREW,P, CROSS, W/ WAS( 8) , M2*4, Zn- Cc
SPRI NG Φ 0. 5*D5* H17 504010000300R 2 509146610200R 4 St eve. Wang 2008. 09. 25
Bl ack vi si on nor mal
SCREW BTP3x4C3UC, ROHS 509112304100R 2 Bol t , #4- 40*12. 5, Ni 509000001000R 4
SCREW, I , CROSS, M3*6, Zn- CcROHS 509016306200R 2 PART NO.
ASSY CHASSI S- BTM, LP2236 701000011200R 1 Scr ew, I , Cr oss, M3*4, Zn- Cc 509016304200R 4 LP2236
4- a 502090313400R 1 Scr ew, P, Cr oss, M4*10, Bl ack- NL 509116610510R 4 MATERI AL
1 2 3 4 5
FORM NO. LMRD4544018G
Service Manual
2. 2209W Disassembly Block
LP2236 DISASSEMBLY BLOCK
chassis* 1
CHASSIS ASSY* 1
slide* 1
spring* 2 Mylar chassis*1
button power key*1
fix-plate1* 1
(P,cross,T.T-3*4,Zn)*1 I/F board* 1
FFC-CABLE*1 POWER, LENS* 1
fix-plate2* 1 (P,Cross,W/WAS,M3*6,Zn-Cc)*3
(P,cross,T.T-3*4,Zn)*1 (BOLT,#4-40,NI)*4
front bezel * 1
clip EMI gnd(3)LP1702*2
shield EMI LP2207*4 CHASSIS-BTM ASSY l ogo- UX383* 1
keypad board*1
power board* 1 (screw,f,cross,

(P,Cross,W/WAS,M3*6,Zn-Cc)*5 T-2*3,BLK)*4
back cover*1 (BOLT,#4-40,NI)*4
(I,Cross,M3*6,Zn-Cc)*2
CHASSIS-TOP * 1
REAR, LOGO*1 slide* 1 CHASSIS-TOP-ASSY* 1
spring* 2 (P,Cross,W/WAS,M3*6,Zn-Cc)*10
bracket vesa left* 1
MI D, FRAME, * 1 bracket vesa right* 1 Invert-chassis
(P,cross,T.T-3*4,Zn)*2 Invert-board
(P,Cross,M2*4)*4
SCREW, I , CROSS, T. clip EMI gnd(3) LP1702*2 Invert-rubber FRONT BEZEL ASSY * 1
Invert-mylar
T- 3* 5, ZN- Cc* 4 CHASSIS-TOP-mylar * 1 (P,Cross,W/WAS,M3*6,Zn-Cc)*4
kensington lock*1 usb board* 1

(P,Cross,W/WAS,M3*6,Zn-Cc)* 1 STAND ASSY* 1
vesa release button*1

usb cover*1
Cable_cover ASSY * 1
PANEL ASSY* 1
(P,Cross,M4*10,BLACK-NL)*4
LABEL, CARD*1
BACK COVER ASSY*1
FINALASSY*1
Note: 1. The arrows point out the direction of disassembly.
33
Service Manual
3. 2209W Assembly Block
LP2236 BOM STRUCTURE

back cover*1
MI D, FRAME, * 1
BACK COVER ASSY*1
LABEL, CARD*1
REAR, LOGO*1
ASSY CHASSIS-BTM SCREW, I , CROSS, T. T- 3* 5, ZN- Cc* 4
CHASSIS-surport kensington lock*1

release button*1
LABEL, CARD* 1
ASSY CHASSIS-BTM, *1 button power key*1

*1
front bezel* 1
l ogo- UX383* 1
BTM-CHASSIS-MYLAR*1 PANEL ASSY*1
TOP-CHASSIS-MYLAR*1 (P,Cross,M4*10,BLACK-NL)*4
(Tape ACE 80*20)*3
Invert board* 1 keypad*1

(SCREW,P,CROSS,W/WAS(8),M2*4,Zn-Cc)*4 FRONT BEZEL ASSY*1
(screw,f,cross,T-2*3,BLK)*4
Rubber*1
AIO board* 1
(P,Cross,W/WAS,M3*6,Zn-Cc)*5 STAND ASSY*1

usb board* 1
(P,Cross,W/WAS,M3*6,Zn-Cc)*1
invert cover*1
usb cover*1 FINAL ASSY*1
panel* 1
CHASSIS-TOP * 1
slide* 1
spring* 2
bracket vesa left* 1
bracket vesa right* 1
(P,cross,T.T-3*4,Zn)*2
clip EMI gnd(3) LP1702*2
(P,Cross,W/WAS,M3*6,Zn-Cc)*12
34
Service Manual
Note: 1. The arrows point out the direction of assembly
35
Service Manual
Chapter 5- TEST AND ADJUSTMENT
Function key Definitions
UP
DOWN
ENTER
MENU
POWER
1. Control buttons on the front bezel
2. KEY FUNCTION
CONTROL KEY KEYS FUNCTION
A. When OSD isn’t shown on screen, press [MENU] to enter OSD interface
[MENU]
B. When OSD displays, press [MENU] to exit OSD
A. When “MENU OSD” displays, press these keys to change the contents of an
adjustment item, or change an adjustment value
[Ù] [Ú]
B. When “MENU OSD” un-displays, press[Ù] to adjust Brightness and Contrast;
And press[Ú]to enter Auto adjustment progress
[ü] Input state select or enter the OSD sub menu when OSD displays
[POWER] Power on or off the monitor
3. Hot Key Operation
HOT KEY OPERATION

FUNCTION DESCRIPTION
MENU [Ù] [Ú] ENTER POWER
Press [Ù]& [MENU] at the same time, and then

FACTORY MODE ● ● ON press [POWER] for DC power on. Press the [Ù] key
to enter factory menu
Brightness& To show the Brightness&

●
Contrast Contrast menu
Auto adjustment ● Enter Auto adjustment progress
Select Input ● Select the input source
36
Service Manual
4. OSD Control
First Second Third Default VGA Input DVI Input
Yes(DCR
Brightness 75 Yes
Brightness off)
Contrast 75 Yes Yes
Auto Adjust Yes No
Auto Select
Input Source VGA Yes Yes
DVI-D
RGB
Input Color Format
YPbPr
PC PC
Gamma
MAC
Graphics
Mode Selection
Video
Standard
Multimedia
Game
Color Settings Yes Yes
Present Modes Warm
Cool
Custom(R,G,B)
Hue 50
Saturation 50
Enable
Demo Mode
Disable
Reset Color Settings
Fill Yes Yes
Wide Mode
4:3
Horizontal Position 50 Yes No
Vertical Position 50 Yes No
Sharpness 50 Yes Yes
Display Pixel Clock 50 Yes No
Settings Phase Yes No
off
Yes No
Dynamic Contrast on
Reset Display Yes Yes

Settings
English
Espanol
Francais
Deutsch
Other Settings Language Yes Yes
Portugues(Brasil)
简体中文
日本語
37
Service Manual
Menu Transparency 20 Yes Yes
Menu Timer 20 Yes Yes
Unlock Yes Yes
Menu Lock
Lock
landscape Yes Yes
Menu rotation
portrait
On Yes Yes
Audio Option
Off
Enable Yes Yes
DDC/CI
Disable
Disable Yes Yes
LCD Conditioning
Enable
Factory Reset Yes Yes
In OSD dialog box, should show current input video signal (1 stands for Auto
Detect, 2 stands for VGA input, 3 stands for DVI input), current model resolution @
Ver. Freq., optimum resolution.
5. OSD Message
After disconnecting the cable, Self Test message should show as below:
“No VGA Cable”
Present input status (1. Auto Detect, 2 VGA input, 3 DVI input), and present
input source should be shown on the top of the message.
After disabling the sync output for VGA (DVI), DPMS message should show as
below for 3s:
“MESSAGE
Entering Power save Mode”
Press the "Ú" or "Ù`" key and the DPMS message should show as below:
“MESSAGE
There is no sigal coming from you computer
Press any key on the keyboard or mouse to wake it or press the
Input button on your display to switch to another source
Factory Mode Introduction
With signal input, press “Power” button on right corner of front bezel to turn off the
monitor. Press “Menu” and “Ù”(Plus )buttons together, and then press “Power” button
to turn on the monitor. After power on, the device is enter factory modode ,press
“Ù”(Plus )buttons to call out factory menu (see the following Fig)
38
Service Manual
Exit: Exit from Factory mode and back to NO OSD Status.

Panel: The current-setting panel is highlighted.
Auto Color: Automatically calibrate chip ADC parameters by using internal DAC.
Burn In: Enable or disable the Burn-in mode by choosing ON or OFF.
Reset Time: Reset the “Turn-on time” of the panel to 0H0M.
Color Temp: The R, G, B of Blue Preset (9300K), Red Preset (5700K) and Normal
Preset (6500K) are generated
from scaling chip’s back-end white-balance program.
Time: Turn-on time of the panel.
DEBUG: Debug tool of scale IC U105.
Dell panel P/N

LCD Panel Supplier P/N Dell P/N
supplier
LGD 22W LM220WE4 P661J
Burn-in pattern
Burn-in pattern will self-generate automatically without VGA and DVI cable plugged in
when the monitor set at Burn-in on mode and burn-in pattern will not be stopped until
39
Service Manual
plugging in the VGA /DVIcable. Exit Burn-in mode method as followe: plugging in the
VGA/DVI cable, press “Menu” button to call out OSD Main Menu, Press “Plus Key”to
select“Other Settings submenu”then choose Factory reset.
Auto Color Balance (Automatically calibrate chip ADC parameter by

using chip internal DAC.)
5.1 If it is a new-built set, press “Auto/Plus” button to execute “Auto Color” at
standard video pattern 5-MOSAIC pattern
5.2 Please confirm the following steps to perform “Auto Color Balance”:
- Connect the VGA cable with the standard video pattern generator and display
5-MOSAIC pattern on the monitor.
- press “Power” button on right corner of front bezel to turn off the monitor.
- Press “Menu” and “Ù”(Plus )buttons together, and then press “Power” button
to turn on the monitor. After power on, the device is enter factory
modode ,press “Ù”(Plus )buttons to call out factory menu
- choose Auto Color item, then execute Auto Color item.
- After the “Auto Color Balance” process finished, go back to “Other Settings Menu”, and press
“Factory Reset” to exit Factory mode
Upgrade Firmware to Serial via Flash Cable by ISP_Tool V4.100.exe

7.1 Connect the monitor and PC follow Fig 11
40
Service Manual
Fig 11
※ The detailed reprogramming procedures will be described in ISP User's Guide.
Edid 8.4.rar Edid.rar ISP User's Guide_20070312.rar ISP_Tool V4.100.rar
After repair, to ensure the quality you should do the following test
and adjustment.
41
Item Content Equipment
Test OSD 1.Signal is set as 1680×1050@60Hz under General-1 Chroma
function Service Manual
2. LCM button are from left to right, checking whether each Signal Generator
single function key and compound function key can be worked.
Contrast Check 1. Set input mode to 1680×1050@60Hz Chroma

2. Set to 32gray scale pattern Signal Generator
3. Set contrast to the maximum. At most 6 bars cannot be
distinguished.
Color 1. Do “Auto color Balance” at 1680×1050@60Hz, 32gray Chroma Signal
Temperature scale pattern Generator and color
2. Measure color temperature, check if it complies with the analyzer
following temperature :
Warm x=0.328 +/- 0.03, y=0.344+/-0.03
Desktop x= 0.313 +/- 0.03, y=0.329+/-0.03
Cool x= 0.283 +/- 0.03, y=0.298+/-0.03
1. Use Chroma Pattern Generator to make sequence. Chroma
Modes switching VESA (640x480 800x600 1024x768 1152x864 1280x1024 Signal Generator
check 1680×1050@60Hz), the detail supported modes (see table 1)
and power saving signal.
2. Confirm the above timing modes must be full screen and
the picture must be normal.
3. LED is amber at power saving mode.
VGA cable When select VGA model and VGA cable is not plugged out, Visual check
detector self-test OSD will be floated.
Minimum 1. LCD minimum luminance spec is 200 cd/m2 (0-15 months from Chroma Signal
luminance mfg. date)
Generator and Color
Analyzer
measurement: 2. 0-15 months: > 80% of minimum luminance
OSD Lock Test Soft Lock: When OSD is locked, this icon should appear for only Visual Inspection
2 seconds with all buttons pressed, except for the “Menu” and
“Power” ones.
Hard Lock: Press “Menu” button for 15 seconds enables the
“locked” icon to be displayed, which will lock All buttons
expect for the “Power”. Press “Menu” button for another 15
seconds enables the “unlock” icon to be shown.
Panel Flicker 1. Mode:1680×1050@60Hz Equipment::
check 2. Set Brightness& Contrast to default value (75%) Chroma Signal
3. Do “Auto Adjustment” Generator & PC
4. check whether there’s flicker on the center of the picture.
Power saving 1. Mode:1680×1050@60Hz Chroma signal

2. Pattern: full Black generator and
3. Brightness: Max. Power meter
4. Contrast: Default AC input:230V/50Hz
5. Check power consumption at each modes
State Power Consumption LED color
＜125W(with USB
& Audio load)
Max brightness
＜100W(without Blue
Power
USB and without
Audio)
Stand By ＜1W Amber
42
Downloaded from www.Manualslib.com manuals search engine ＜Ｗ
Service Manual
43
Service Manual
Chapter 6- TROUBLE SHOOTING
Common Acknowledge
l If you change the M/B, be sure that the U101,U102 and U105 these three
components also changed to the new M/B because there was program inside.
If not, please re-write EDID or upload firmware into serial flash(U105) via
VGA Cable. How to do please refer to the Page 19.
l If you adjust clock and phase, please do it at condition of Windows shut
down pattern.
l Please confirm the R/G/B color under 32gray scale pattern.
l This LCM is analog interface. So if the entire screen is an abnormal color
that means the problem happen in the analog circuit part, if only some scale
appears abnormal color that stand the problem happen in the digital circuit
part.
l If you check the H/V position, please use the crosshatch pattern.
l This LCM support 10 timing modes, if the input timing mode is out of
specification, “Cannot Display this Video Mode” will be displayed on the
screen.
l If brightness uneven, repairs Inverter circuit or change a new panel.
l If you find the vertical line or horizontal line lost on the screen, please
change panel.
l If the self-test pattern is moving on the screen, please check whether VGA
Cable is plugged in the Monitor or PC if select analog model on OSD or
check whether DVI Cable is plugged in the Monitor or PC if select DVI
model on OSD . If the VGA or DVI Cable is plugged in well, please change
another VGA or DVI cable.
No Power and LED Off
Is there DC16V at L852
Is there DC5V at L851
NO
Is the voltage at C854 in the

range of 127V~339V?
YES NO
Check RT850, F850
Is the voltage at pin8 of U850 354V?
YES NO Check R853
Is the voltage at pin5 of U850 18.2V?
YES NO
Check D852
Is the voltage at pin3 of T850

44
about 518V?
Service Manual
Power(include IF +5Vand +3.3V) supply normal but LED off and no
display
Is the key function OK? Yes Press power key to DC on the monitor,if
display ok the process is end,if no
NO display see the no backlight process
Is the frequency 14.318MHz at #128 of NO

IF Board U105? Change crystal X101
Yes
NO
Change C164
Is the low active reset signal at #108 of
IF Board U105 normal?
NO
Yes Yes Change U105
Is the serial clock signal at #6 of IF NO

Board U108 normal when power AC on? Change U108
Yes
Upgrade Firmware to Serial Flash U108 NO Change U105
by VGA port with ISP_Tool V4.100.exe
END
Power(include IF +5Vand +3.3V) supply and display normal only

LED off
Is the keypad cable connective OK NO
Reassembly or changing
Yes
Is LED at keypad work OK NO Change LED
Yes
yes
Is R165 open? Change R165
NO
NO
Is Q107 work normal? Change Q107
Yes
Is the LED control signal at 123# of NO Change U105
U105high-low convertible when DC on/off
45

Service Manual
END
Power (include IF +5Vand +3.3V) supply normal but LED Amber
Is Power LED Amber?
YES
NO
Do the Hsync. & Vsync. Signals exist Insert VGA Cable correctly
in CN102 #13& #14 separately when
select VGA mode by OSD?
YES
Do the Hsync. & Vsync. Signals exist NO

in R136 & R136 Check R135 & R136
YES
Do the Hsync. & Vsync. Signals exist NO

in U105#32& #33? Check R133 & R134
YES
Change U105
END
46

Service Manual
4.Power (include IF +5Vand +3.3V) supply normal ,key function

OK,but backlight can’t be turned on
Backlight cannot be turned on,is the NO
on-off control signal come from IF ok?
Yes Is the on-off control signal #109 of U105

Yes high-low convertible when DC on/off
NO
Is the Change U105

voltage NO Check
16V at T1 T850 or
PIN4? F850
Yes
Check U1
pin6 Voltage
is 5V
Yes
Check U1 pin1 NO Check

Voltage is Q3
lower
YES
Check T1 pin7 and pin10 Open or
Short
Yes
Change T1
47

Service Manual
5. Backlight on,key function and LED accurate indication ok but no picture
Backlight on,key function and LED

accurate indication ok but no picture
YES
Is the panel enable
YES signal at 73# of
IS the display is white and cannot Check DC 5.0V on NO
U105,if no check
display OSD when press key? CN103#1, #2, #3
Q104 circuit or cha
U105,if yes Check
Q101 circuit
NO
VGA
Is display selftest picture at Is there R.G.B signal in Check VGA input
VGA mode or DVI mode? U105 #28, #25 #23? NO circuit (D105, D1
D103 R114 R115 R1
DVI C113 C114 C115)
Yes
YES Are there data output on YES Is the FFC cable

Is there DVI signal in U105 #9,
U105#77~#86, inserting ok,if no
#10,#12,#13,#15,#16,#18 #19?
#91~#100 reinsert else
change FFC cabl
No
Change U105
Check DVI input circuit

(D202~D209 and
END
R201~R208)
48

Service Manual
6.At 32-gray scale pattern, color lost in some scale
Color lost in some scale at 32-gray scale pattern
OK,
Re-insert the FFC Cable END
NO
OK,
Change FFC Cable END
NO
Check crystal circuit, if the wave of 14.318MHz
signal is normal change U105 else change X101
END
Chapter 7- RECOMMENDED PART LIST
2209WA Critical Parts List

Component Component
Itm Category Type Location Supplier number Suppiler PN Object description
SAMXON ERT127M2WL45PB**P
CAP SE 120UF/450V M,105
1 Critical E-CAP C854, SU'SCON 420271214585R SE450M121K45T022ZCFR
CF 18X45(BLA),
ELITE PV2W121MS31845RP
FOXCONN 2MCQA2620-002A
FRONTIER SPV2620-10-LFR COIL CHK PQ2620 JPP4 450u

2 Critical PFC-CHOCK L853, 425000011080R
LISHIN QFK8002EL CHK-108 ROHS
MEIKAI TP2620A-451
FOXCONN 2MWQA3220-002A
FRONTIER SPV3205-01-LFR XFMR SW DIP PQ3220 PC44

3 Critical Transformer T850, 426000091280R
LISHIN PFK8032EL 700uH SPW-128
MEIKAI BCK-3218
FOXCONN 2MWQA2620-002A
FRONTIER SPV2602-11-LFR XFMR SW DIP PQ2620 PC44

4 Critical Transformer T900, 426000091290R
LISHIN PFK8031EL 650uH SPW-129
MEIKAI BCK-2556
49

Service Manual
IC SG6901ASZ
5 Function IC U850, SG, 412000532021R SG6901ASZ
SOP20(SG)RoHS
IC LD7575PS
6 Function IC U950, LEADTREND, 412000453820R LD7575PS
SOP8(LEADTREND) RoHS
IC CAT24C02WI-TE13
CATALYST 412000480990R CAT24FC02WI-TE13
SOIC-8(CATALYST)RoHS
7 Performance EEPROM U103,U201 IC M24C02-WMN6TP SO8 2K
ST 412000480280R M24C02-WMN6TP
(ST)
IC AT24C02BN-SH-T 2K
ATMEL 412000435481R AT24C02BN-SH-T 2K
SOIC8(ATMEL)RoHS
IC AT24C16BN-SH-T
ATMEL 412000224482R AT24C16BN-SH-T
16K(ATMEL) SOIC 8 ROHS
IC M24C16-WMN6TP SO8 16K
8 Performance EEPROM U106 ST 412000224280R M24C16-WMN6TP
(ST) ROHS
IC CAT24C16WI-TE13
CATALYST 412000481990R CAT24C16WI-TE13
SOIC-8(CATALYST)RoHS
IC LD1117AL-3.3V-A
UTC 412000372020R LD1117AL-3.3V-A
SOT-223(UTC RoHS
IC
AISEMI 412000372830R AS1117R-3.3 AS1117L-3.3TR-LF,SOT223(A1
9 Critical Regulator U301 EMI)RoHS
IC EC50117KBG 3.3V
E-CMOS 412000598990H EC50117KBG 3.3V
SOT223(E-CMOS)
IC AZ1117H-3.3
BCD, 412000372070R AZ1117H-3.3
SOT-223(AAC)RoHS
ANACHIP, 412000332130R AP1117D33LA 3.3V
IC AP1117D33LA 3.3V
(ANACHIP) TO-252-3L,
10 Critical Regulator U101 A1SEMI, IC
412000332830R AS1117R-3.3.TR-LF, AS1117R-3.3.TR-LF,TO-252(A1
SEMI)RoHS
IC EC50117BBG 1.8V
E-CMOS 412000599990H EC50117BBG 1.8V
SOT223(E-CMOS)
IC LD1117AL-1.8V-A
UTC 412000330020R LD1117AL-1.8V-A
SOT223(UTC)
11 Critical Regulator U102
IC
A1-SEMI 412000330830R AS1117L-1.8/TR
AS1117L-1.8/TR-LF,SOT223(A
IC AZ1117H-1.8
BCD, 412000330070R AZ1117H-1.8
SOT223(AAC)RoHS
IC USB2514-AEZG
12 Function IC U302 SMSC 412000668390R USB2514
36QFN(SMSC)
IC SST25LF020A-33-4C-SAE
SST 412000494190R SST25LF020A-33-4C-SAE
SOIC8(SST)ROHS
IC MX25L2025MC-12G
14 Function Serial Flash U108 MXIC 412000661620R MX25L2025MC-12G
SOP8(MXIC)RoHS
IC PM25LV020-100SCE
PMC 412000494310R PM25LV020-100SCE
SOIC8(PMC)RoHS
IC TSUMU58EHJ-LF-2
15 Function Scaler U105 MSTAR 412000653060R TSUMU58EHJ-LF-2
PQFP128(MSTAR)Rohs
CVILUX C11330MG
CON, SMD 1.0MM 30PIN with
16 Function connector CN103 444099030040R
lock RoHS
P-TWO HS9030E
EXPRESS
PCB,K/P ,2/ENIG/FR4
17 PCB PCB 491881500000H PCB
/08,LP2236,HF
HsiangKuo
HsiangKuo
PCB,CNV-U,1/OSP
18 PCB PCB 491660300100H PCB
/CEM1/12,LP1931 HF
TAT CHUN
HsiangKuo
PCB,M/B ,2/OSP /FR4
19 PCB PCB 491881200100H PCB
/12,LP2236,HF
EXPRESS
20 Function connector P1,P2, FOXCONN 444179001010R CONN SPRING H/V CONN SPRING H/V 1P RO
50

Service Manual
P3,P4,
P5,P6,
P7,P8,
P9,P10, CVILUX
P11,P12
CVILUX
FCN 10P 2.0MM 90° WFR 10P 2.0MM 90° SMD

21 Function connector CN1, 430631100070R
SMD W/LOCK W/LOCK ROHS
JOWLE
CAP OS SVPD 47UF 35V M,

22 Function Capcitor C5 Sanyo F12 35SVPD47M
421024700350R ℃ SMD 10X13
XSTR
APEC 410050108290R AP9962AGH AP9962AGH,N-CH,TO252(A
RoHS
23 Critical Mosfet Q1,Q2,Q3,Q4,
XSTR
NIKO 410050108430R P1504BDG P1504BDG,N-CH,TO252(NIK
RoHS
IC OZ9926A SOIC24(O2
24 Performance IC U1 O2 412000689630R OZ9926A
MICRO)RoHS
EXPRESS
PCB,INV ,2/OSP /FR4
25 PCB PCB 491882200100H PCB
/12,LP2236
Hsiangkuo
T1,T2,T3, DARFON
T4,T5,T6,
FRONTIER XFMR SW SMD EE13 P4
26 Function Transformer T7,T8,T9, 426000091270R SPW-127
SPW-127 ROHS
T10,T11,
T12 TDK
27 Mylar Mylar 富准 505040209902R INVERT-MYALR,LP2236 INVERT-MYALR,LP2236
ATTACHMENT 1- Bill of Material

1. main board BOM
ITEM P/N Description Supplier Usage Location
791921200A00R PCBA,MAIN BOARD,W/O SPK,LP2236-A19,ROHS
10 791921220A00R PCBA,MAIN BOARD,W/O SPK,MI,LP2236-A19,RO 1
20 791921210A00R PCBA,MAIN BOARD,W/O SPK,AI,LP2236-A19,RO 1
30 629030023600R PROGRAM,W/O SPK,LE23M7-A18 ROHS 1
40 641120000010R HDCP RECEIVE DEVICE KEY DCP LLC, 1
50 511130001200R SOLDER BAR,Sn96.5/Ag3.0/Cu0.5/Ni0.06/Ge0 TOMAS, 14
60 511110000501R SILICONE RTV RUBBER,UB-511(EURO) EURO, 0.45
70 511110000103R HOT-MELT ADHESIVES,UB-618 U-BOND, 2.1
70 511110000101R HOT-MELT ADHESIVES (#526) EXCELSTAR, 0

791921210A00R PCBA,MAIN BOARD,W/O SPK,AI,LP2236-A19,RO
10 791921250A00R PCBA,MAIN BOARD,W/O SPK,AI/A,LP2236-A19, 1
20 791921260A00R PCBA,MAIN BOARD,W/O SPK,AI/R,LP2236-A19, 1

791921220A00R PCBA,MAIN BOARD,W/O SPK,MI,LP2236-A19,RO
51

Service Manual
ARCOTRONIC,
10 416193343012R CAP MEX 0.33uF 275V K X2,F15mm RoHS 2 C852,C853,
EUROPTRONIC,HJC,SCC,
20 416211023620R CAP MEY 1000pF 250V M Y1,F10mm W/O FORMI JNC,POE,SUCCESS(SEC), 4 C885,C886,C
30 416212223620R CAP MEY 2200pF 250V M Y1,F10mm W/O FORM JNC,POE,SUCCESS(SEC), 3 C850,C851,C
40 420271214585R CAP SE 120UF/450V M,105℃ CF 18X45(BLA), ELITE,SAMXON,SU'SCON, 1 C854,
50 416351054011R CAP MPPN ROUND 1UF/450V K F15 MINI EUROPTRONIC, 1 C874,
60 416300144510R CAP PP 0.01uF 400V J,F7.5 RoHS EUROPTRONIC,HJC,SCC, 1 C855,
70 416304724510R CAP PP 0.0047uF 400V J,F5,RoHS EUROPTRONIC,HJC,NISSEI,SCC, 1 C955,
80 440149000340R SKT AC 10A/250V U/C/V,W/O H ROHS DLK,TECX, 1 CN850,
90 442299001100R CON,POWER JACK R/A 1P,JPD1030- H224-4F,R DLK,FOXCONN,S.C.,ZJGHJ, 1 CN853,
100 411030060013R DIO FR307G-03 1000V/3A DO-201AD(TSC) TSC, 1 D851,
100 411030060023R DIO FR30-10G 1000V/3A DO-201AD(FRONTIER FRONTIER, 0
110 411090050092R SCHTKY SB5150F46 150V/5A DO-201AD (PANJI PANJIT, 2 D930,D931,
110 411090050012R SCHTKY SR5150PT-A3 150V/5A DO-201AD (CH CHENMKO, 0
120 411020078020R DIO IN5406F64-LF 600V/3A DO-201AD(FEC)R FRONTIER, 1 D856,
120 411020078090R DIO IN5406 600V/3A DO-201AD-F112(PEC)RoH PANJIT, 0
130 412140002380R IC LTV817M-PR VDE (LITE-ON) P=10mm RoHS LITEON, 3 I850,I950,I952
130 412140001390R IC EL817M-B(EVERLIGHT)RoHS EVERLIGHT, 0
CHILISIN,EASYMAGNET,
140 425000011090R COIL CHK BR3X20 2.2uH ROHS 2 L854,L953,
FRONTIER,TAICHANG,
FOXCONN,FRONTIER,
150 425000011110R COIL CHK T9*5*3-C A05 64uH CHK-111 1 L930,
TAICHANG,
FUTABA,QUEENMAO,
160 415350100550R RES MOF 2W 10Ω J,MINI,HK15, RoHS 1 R960,
TZAI YUAN,UNIOHM,
FUTABA,QUEENMAO,
170 415503228530R RES WW 3W 0.22 OHM J,KNP HK20 MINI 1 R870,
TZAI YUAN,UNIOHM,
FUTABA,QUEENMAO,
180 415360200550R RES MOF 3W 20Ω J,HK20 ,MINI,RoHS 1 R856,
TZAI YUAN,UNIOHM,
FUTABA,QUEENMAO,
190 415360753550R RES MOF 3W 75KΩ J,HK20, MINI, ROHS 1 R855,
TZAI YUAN,UNIOHM,
FUTABA,QUEENMAO,
200 415502128551R RES NKNP 2W 0.12Ω J, MINI,HK17.5,ROHS 1 R853,
TZAI YUAN,UNIOHM,
FUTABA,QUEENMAO,
210 415502518551R RES WW NKNP 2W 0.51Ω J,MINI,HK15 ROHS 1 R959,
TZAI YUAN,UNIOHM,
220 432009401400R NTC 3Ω 5A 10ψ P=5mm, F RoHS THINKING,UPPERMOST, 1 RT851,
230 432009401500R NTC 3Ω 7A P=7.5mm 15∮,F, RoHS THINKING,UPPERMOST, 1 RT850,
C862,C863,C
240 420264710322R CAP 470uF/35V M,13x21max,125℃ ,S 3000h SAMXON,SU'SCON, 5
C865,C931,
FUTABA,QUEENMAO,
250 415360101550R RES MOF 3W 100Ω J,HK20,MINI, ROHS 1 R930,
TZAI YUAN,UNIOHM,
CHILISIN,EASYMAGNET,
260 425000011100R COIL CHK T22*14*8-C A10 11mH CHK-110 2 L851,L852,
FRONTIER,TAICHANG,
FOXCONN,FRONTIER,
270 425000011080R COIL CHK PQ2620 JPP4 450uH CHK-108 ROHS 1 L853,
LISHIN,MEIKAI,
FOXCONN,FRONTIER,
280 426000091280R XFMR SW DIP PQ3220 PC44 700uH SPW-128 1 T850,
LISHIN,MEIKAI,
FOXCONN,FRONTIER,
290 426000091290R XFMR SW DIP PQ2620 PC44 650uH SPW-129 1 T900,
LISHIN,MEIKAI,
300 430301000210R HRN ASS'Y 10P 100mm UL1007#24 LOCK FOXCONN,JVE,RISE, 1 CN852,
52

Service Manual
CON D-SUB FEM.15P RA W/O SCREW DLK,FOXCONN,
310 440819015030R 1 CN102,
DZ11AA1-H TEKCON,ZJGHJ,
320 430631080180R WFR 2X4P 2.0MM 180° W/LOCK ROHS CVILUX,FOXCONN, 1 CN104,
330 443842024060R CON DVI-D RA 24+1P FEM.W/O SCR EW QH1112 DLK,FOXCONN,ZJGHJ, 1 CN201,
340 432008010270R XTAL 14.31818MHz HC-49US DIP 16pF 30PPM HUAN MOUN,TXC,ZGC, 1 X101,
350 432008010310R XTAL 24.000MHz 20pF HC-49US 30PPM DIP,Ro HARMONY,TXC,ZGC, 1 X301,
360 442849001020R CON USB R/A 1P UC11123-LK1-4F, RoHS FOXCONN,TEKCON, 1 P301,
370 442849001030R CON USB A,R/A,8 POS,T/H UB11123-8D1-4F,R FOXCONN,TEKCON, 1 P302,
380 430300802110R HRN ASS'Y 8P 100MM UL1430#26 FOXCONN,HEIGHTEN,JVE, 1 CN303,
390 735110010100R ASSY H/S,D853,D854,ROHS 1
400 735110010110R ASSY,H/S,D960,D961,ROHS 1
410 735110010120R ASSY,H/S,Q853&D860,ROHS 1
420 735110010130R ASSY,H/S,Q850,ROHS 1
430 735110010140R ASSY,H/S,D850,ROHS 1
440 735110010150R ASSY H/S,Q950,ROHS 1

735110010100R ASSY H/S,D853,D854,ROHS
10 411090031460R SCHTKY SP10200-LF 200V/10A ITO220(SECOS) SECOS, 2 D853,D854,
10 411090030020R SCHTKY SRF10-20CT-LF 200V/10A,ITO-220AB( FRONTIER, 0
10 411090031010R SCHTKY MBRF10200CT 200V/10A ITO220AB(TSC TSC, 0
10 411090031311R SCHTKY,SBR10200CTFP 200V/10A ITO-220AB(D DIODES, 0
20 507200007800R HEATSINK,40 X20Xt15mm,LP2236 DMC,ORIENTAL POWER, 1
30 509146308102R SCREW,PW,CROSS W/WAS,M3*8,Zn GAOYI,LIQUAN,YIJIE, 2

735110010110R ASSY,H/S,D960,D961,ROHS
10 411090009460R SCHTKY SP10100-LF 100V/10A ITO220(SECOS SECOS, 2 D960,D961,
10 411090009312R SCHTKY,SBR10100CTFP 100V/10A ITO-220AB(D DIODES, 0
10 411090009020R SCHTKY SRF10-10CT-LF 100V/10A TO-220AB(F FRONTIER, 0

735110010120R ASSY,H/S,Q853&D860,ROHS
10 410050087240R XSTR FQPF12N60C N-CH TO220F(FAIRCHILD)Ro FAIRCHILD, 1 Q853,
10 410050086370R XSTR 2SK3797 N-CH SC-67(TOSHIBA)RoHS TOSHIBA, 0
XSTR STP13NK60ZFP, N-CH
10 410050098280R ST, 0
TO220FP(ST)ROHS
20 411030059240R DIO ISL9R860PF2 600V/8A TO220F(FAIRCHIL FAIRCHILD, 1 D860,
20 411030059280R DIO STTH8R06FP 600V/8A TO-220FPAC(ST)RoH ST, 0
20 411030059210R DIO BYC8X-600 600V/8A TO220F(philips) PHILIPS, 0
40 509116308100R SCREW,P,CROSS,M3*8,Zn GAOYI,YIJIE, 2

735110010130R ASSY,H/S,Q850,ROHS
10 410050084130R XSTR SPA11N80C3 N-CH PG-TO220-3-31(INFIN INFINEON, 1 Q850,
10 410050085280R XSTR STF11NM80 N-CH TO220FP(ST)RoHs ST, 0
10 410050057280R XSTR STP8NK80ZFP N-CH TO220FP (ST) ST, 0
53

Service Manual
10 410050060130R XSTR SPA06N80C3 N-CH PG-TO220- 3-31(INFI INFINEON, 0

735110010140R ASSY,H/S,D850,ROHS
10 411050011090R DIO BRDG GBU8J 600V/8A(PANJIT)RoHS PANJIT, 1 D850,
10 411050010020R DIO BRDG GBU8-06-BF52-LF 600V/8A(FEC)RoH FRONTIER, 0
20 507200007810R HEATSINK,30x20xt15mm,for D850,LP2236 DMC,ORIENTAL POWER, 1

735110010150R ASSY H/S,Q950,ROHS
10 410500059290R XSTR AP2761I-A N-CH TO-220CFM ADVANCED P APEC, 1 Q950,
10 410050103050R XSTR FMA09N65GX N-CH TO-220F(FUJI) RoHS FUJI, 0
10 410050057280R XSTR STP8NK80ZFP N-CH TO220FP (ST) ST, 0
10 410050060130R XSTR SPA06N80C3 N-CH PG-TO220- 3-31(INFI INFINEON, 0
20 507200007820R HEATSINK,30x20xt15mm,for Q950,LP2236 DMC,ORIENTAL POWER, 1

791921250A00R PCBA,MAIN BOARD,W/O SPK,AI/A,LP2236-A19,
10 411020063020R DIO 1N4007-LF 1000V/1A DO-41(F RONTIER)R FRONTIER, 2 D858,D859,
10 411020063010R DIO 1N4007 1000V/1A DO-41(TSC) RoHS TSC, 0
10 411020063040R DIO 1N4007 1000V/1A DO-41(MOSPECRoH MOSPEC, 0
10 411020063460R DIO 1N4007-LF 1000V/1A DO-41(Secos)RoHS SECOS, 0
10 411020063240R DIO 1N4007 1000V/1A DO-41(FAIR CHILD)RoH FAIRCHILD, 0
20 411032006020R DIO FR10-10-LF 1000V/1A AT(FRO NTIER)RoH FRONTIER, 1 D951,
20 411020053090R DIO PS1010R 1000V/1A DO-41(PAN JIT)RoHS PANJIT, 0
20 411032006040R DIO FR107 1000V/1A DO-41(MOSPE C)RoHS MOSPEC, 0
FUTABA,QUEENMAO,
30 415340472540R RES MOF 1W 4.7KΩ J,AT MINI RoHS 1 R865,
TZAI YUAN,UNIOHM,
FUTABA,QUEENMAO,
40 415320152540R RES MOF 1/4W 1.5KΩ J,AT MINI RoHS 1 R859,
TZAI YUAN,UNIOHM,
FUTABA,QUEENMAO,
50 414040208540R RES FSM 1W 0.2Ω J,AT MINI RoHS 3 FR850,FR950
TZAI YUAN,
60 430613050100R FUSE SLOW PICO II 5A/125V U/C,AT,ROHS LITTELFUSE, 1 F853,
60 430613050101R FUSE SLOW 5A/125V U/C,AT,ROHS WALTER, 0
L855,L856,L8
70 432002200220R FERRTIE BEAD 3.5*6*0.65 AT,RoHS CHILISIN,MAGLAYERS, 6
L858,L859,L8
80 411130620020R ZENER 20V GDZ20B-LF DO34(FEC)ROHS FRONTIER, 2 ZD951,ZD930
80 411130920020R ZENER 20V GDZ20B DO34(PEC)ROHS PANJIT, 0
90 411130656920R ZENER 5.6V GDZ5.6B-LF DO-34(FR ONTIER)Ro FRONTIER, 1 ZD971,
90 411130956910R ZENER 5.6V GDZ5.6B DO35(PANJIT)RoHS PANJIT, 0
90 411131456910R ZENER 5.6V GDZ5.6B DO35(WILLAS)RoHS WILLAS, 0
100 411130630020R ZENER 30V GDZ30A-LF DO34(FEC)ROHS FRONTIER, 1 ZD972,
100 411130930010R ZENER 30V GDZ30A DO35(PANJIT)RoHS PANJIT, 0
100 411131430010R ZENER 30V GDZ30A DO35(WILLAS)RoHS WILLAS, 0
110 411130616011R ZENER 16V GDZ16A-LF DO-34(FRONTIER)RoHS FRONTIER, 1 ZD973,
110 411130916011R ZENER 16V GDZ16A DO35(PANJIT)RoHS PANJIT, 0
54

Service Manual
120 411020084090R DIO P6KE350A 600W/100A DO-15（PANJIT） PANJIT, 1 ZD851,
120 411020084010R DIO P6KE350A 600W/100A DO-15（TSC） TSC, 0
130 791921240A00R PCBA,MAIN BOARD,W/O SPK,SMT,LP2236-A19,R 1
140 411020064090R DIO ER104 400V/1A DO-41(PANJIT RoHS PANJIT, 1 D952,
140 411032001020R DIO SF10-04-LF 400V/1A DO-41(F RONTIER)R FRONTIER, 0
150 430613040100R FUSE SLOW PICO II 4A/125V U/C,AT,RoHS LITTELFUSE, 2 F851,F852,
150 430613040101R FUSE SLOW 4A/125V U/C,AT,RoHS WALTER, 0

791921260A00R PCBA,MAIN BOARD,W/O SPK,AI/R,LP2236-A19,
JNC,POE,
10 418210233030R CAP CD X7R 1000pF/1KV K,VT 2X7R102K102K5 2 C858,C930,
SUCCESS(SEC),WANSHENG,
JNC,POE,SUCCESS(SEC),
20 418222263030R CAP CD X7R 2200pF/100V K,VT ,RoHS 1 C960,
WANSHENG,
30 418210133030R CAP CD X7R 100pF 1KV K VT RoHS 3 C881,C882,C
WANSHENG,
40 420221000530R CAP HG 10uF 50V M,105℃ VT,5x11,RoHS LELON,SAMXON,SU'SCON, 1 C957,
50 420224700530R CAP HG 47uF/50V M,105℃ VT,6.3X11,ROHS LELON,SAMXON,SU'SCON, 4 C952,C103,C
60 420424710260R CAP SD 470uF/25V M 105℃ ST 10x16,RoHS LELON,SAMXON,SU'SCON, 1 C933,
80 420264710260R CAP SH 470u/25V M,125C, ST, 10*16 SAMXON,SU'SCON, 2 C964,C932,
BELFUSE,CONQUER,
90 430613830290R FUSE TIME LAG 3.15A/250V,RoHS 1 F850,
LITTELFUSE,WALTER,
100 412022002550R IC AME431BAJATB25Z TO-92-3(AME RoHS AME, 3 I851,I951,I930
100 412022002240R IC KA431AZ 1%,VT (FAIRCHILD) RoHS FAIRCHILD, 0
100 412022002830R IC AS431 TO-92 VT(A1SEMI)RoHS A1SEMI, 0
100 412022002440R IC AZ431BZ-ATRE1 TO-92(BCD) RoHS BCD, 0
110 410052001370R XSTR SF0R3G42 TO-92 VT(TOSHIBA RoHS TOSHIBA, 1 Q971,
110 410052005150R THYRI MCR101L-6 TO-92(UTC)RoHS UTC, 0
120 418210313030R CAP CD X7R 0.01UF 50V K,VT,ROHS 2 C861,C961,
WANSHENG,
130 418222233030R CAP CD X7R 2200pF 1KV K,VT RoHS 2 C867,C868,
WANSHENG,
140 420431010431R CAP EC 100uF 16V M,105℃ VT 5x11,RoHS ELITE,LELON,SAMXON,SU'SCON, 1 C109,
150 420434700430R CAP SM 47uF 16V M,105℃ VT 5x11 RoHS ELITE,LELON,SAMXON,SU'SCON, 3 C305,C307,C
160 420434790430R CAP EC 4.7uF 16V M,105℃ VT, 5x11,RoHS ELITE,LELON,SAMXON,SU'SCON, 4 C312,C313,C
170 421013310460R CAP OS SEP 330UF 16V M,105℃ ST 10X13 NICHICON,SANYO, 2 C962,C963,
190 420221010430R CAP HG 100UF 16V M,105℃ VT,6.3X11,ROHS LELON,SAMXON,SU'SCON, 1 C102,

791921240A00R PCBA,MAIN BOARD,W/O SPK,SMT,LP2236-A19,R
DARFON,MURATA,
10 419341050650R C SMD(1206) Y5V 1uF/50V Z RoHS 2 C812,C822,
TAIYO,TDK,WALSIN,YAGEO,
DARFON,MURATA,
20 419341063650R C SMD(1206) Y5V 10uF/25V Z RoHS 1 C818,
C814,C954,C
30 419311020010R C SMD(0402) X7R 1000PF/50V K,RoHS DARFON,TDK,WALSIN,YAGEO, 6
C967,C123,C
40 419312220010R C SMD(0402) X7R 2200PF/50V K RoHS DARFON,TDK,WALSIN,YAGEO, 1 C821,
50 419311030070R C SMD(0805) X7R 0.01uF/50V K RoHS DARFON,TDK,WALSIN,YAGEO, 3 C816,C891,C
60 419301010510R C SMD(0402) NPO 100PF/50V J,RoHS DARFON,TDK,WALSIN,YAGEO, 1 C819,
70 419314720070R C SMD(0805) X7R 4700PF/50V K ROHS DARFON,TDK,WALSIN,YAGEO, 2 C811,C817,
55

Service Manual
80 419314720010R C SMD(0402) X7R 4700PF/50V K ROHS DARFON,TDK,WALSIN,YAGEO, 2 C813,C820,
90 419314730070R C SMD(0805) X7R 0.047uF/50V K ROHS DARFON,TDK,WALSIN,YAGEO, 2 C872,C968,
DARFON,MURATA,
100 419311054070R C SMD(0805) X7R 1uF/16V K RoHS REV:A 2 C897,C164,
120 419311040070R C SMD(0805) X7R 0.1uF/50V K RoHS REV:A DARFON,TDK,WALSIN,YAGEO, 2 C951,C969,
DARFON,MURATA,
140 419341069680R C SMD(1210) Y5V 10uF/35V Z RoHS 1 C866,
DARFON,MURATA,
140 419341069650R C SMD (1206) Y5V 10UF/35V Z ROHS 0
160 410050069291R XSTR AP9972GS N-CH TO-263(APEC)RoHS APEC, 1 Q930,
170 410090010210R XSTR PMBT2907A PNP SOT23(PHILI PS)RoHS PHILIPS, 2 Q953,Q931,
170 410090010090R XSTR MMBT2907A PNP SOT23(PANJIT)RoHS PANJIT, 0
180 410070010240R XSTR MMBT4401 NPN SOT23(FAIRCHILD)RoHS FAIRCHILD, 2 Q951,Q932,
180 410070010420R XSTR MMBT4401 NPN SOT23(PANJIT)RoHS PANJIT, 0
180 410070010210R XSTR PMBT4401 NPN SOT23(PHILIPS)RoHS PHILIPS, 0
190 410500050212R XSTR 2N7002K01 ESD N-C SOT-23( PHILIPS)R PHILIPS, 2 Q861,Q860,
190 410500050230R XSTR RK7002 ESD N-C SOT-23 (ROHM)RoHS ROHM, 0
190 410500050091R XSTR 2N7002K ESD N-C SOT-23, (PEC)RoH PANJIT, 0
200 411023004021R DIO SN4148-LF 75V/0.15A SMD 1206 (FEC)Ro FRONTIER, 2 D953,D932,
200 411020046090R DIO 1N4148W 75V/0.15A(PEC)RoHS SOD-123 PANJIT, 0
200 411020046310R DIO 1N4148W-F 75V/0.15A(DIODES RoHS,SOD- DIODES, 0
210 414908068350R RES SMD (0805) 68KΩ J,RT,ROHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R813,
220 414908158210R RES SMD (0805) 15.8KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R989,
230 414908240210R RES SMD (0805) 24KΩ F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R814,R822,
240 414908200010R RES SMD (0805) 200Ω F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 4 R825,R971,R
250 414908464210R RES SMD (0805) 46.4KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R821,
260 414908105210R RES SMD (0805) 10.5KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R829,R963,
270 414908866210R RES SMD (0805) 86.6KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 1 R860,
280 414918200210R RES SMD (0402) 20KΩ F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R940,R932,
290 414908680110R RES SMD (0805) 6.8KΩ F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R969,
300 414908470110R RES SMD (0805) 4.7KΩ F,RT,RoH S TA-I,UNIOHM,WALSIN,YAGEO, 1 R864,
310 414918270110R RES SMD (0402) 2.7KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R817,R818,
R885,R886,R
320 414908100210R RES SMD (0805) 10KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 12 R858,R951,R
R937,R962,R
340 414918100110R RES SMD (0402) 1KΩ F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R816,
350 414908100110R RES SMD (0805) 1KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 2 R943,R970,
360 414908100010R RES SMD (0805)100Ω F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R824,
370 414904100110R RES SMD (1206) 1KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R931,
380 414904200910R RES SMD (1206) 20Ω F,RT ROHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R854,R875,
390 414908047150R RES SMD (0805) 470Ω J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R942,R957,
400 414904300310R RES SMD (1206) 300KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 4 R831,R832,R
410 414904120410R RES SMD (1206) 1.2MΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 4 R871,R872,R
R835,R836,R
420 414904020350R RES SMD (1206) 20KΩ J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 5
R839,
R981,R982,R
430 414904499310R RES SMD (1206) 499KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 8
R985,R986,R
440 414904374310R RES SMD (1206)374KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 4 R891,R892,R
56

Service Manual
450 414918100210R RES SMD (0402) 10KΩ F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 3 R898,R935,R
460 414918392210R RES SMD (0402) 39.2KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 1 R938,
470 414908047050R RES SMD (0805) 47Ω J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R956,
490 414908330010R RES SMD (0805) 330Ω F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R964,
500 414908022250R RES SMD (0805) 2.2KΩ J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R968,R878,
520 412000532021R IC SG6901ASZ SOP20(SG)RoHS SG, 1 U850,
530 412000453820R IC LD7575PS SOP8(LEADTREND) RoHS LEADTREND, 1 U950,
540 444099030040R CON, SMD 1.0MM 30PIN with lock RoHS CVILUX,P-TWO, 1 CN103,
C104,C106,C
C110,C111,C
C126,C128,C
C135,C136,C
C139,C140,C
C144,C145,C
C149,C153,C
C156,C159,C
DARFON,MURATA,
550 419351044010R C SMD(0402) X5R 0.1uF/16V K,RoHS 65 C165,C167,C
C170,C171,C
C174,C175,C
C207,C208,C
C211,C212,C
C304,C309,C
C316,C317,C
C320,C321,C
C326,
C113,C114,C
570 419314734010R C SMD(0402) X7R 0.047uF/16V K,RoHS DARFON,TDK,WALSIN,YAGEO, 7
C120,C121,C
580 419302700510R C SMD(0402) NPO 27PF/50V J RoHS DARFON,TDK,WALSIN,YAGEO, 2 C130,C129,
DARFON,MURATA,
590 419351054060R C SMD(0603) X5R 1uF/16V K,RoHS 2 C148,C315,
600 419302200510R C SMD(0402) NPO 22PF/50V J,RoHS DARFON,TDK,WALSIN,YAGEO, 4 C157,C158,C
D102,D103,D
D202,D203,D
610 411020026210R DIO BAV99 350mW 70V SOT-23(PHI RoHS PHILIPS, 13
D206,D207,D
D210,
610 411020026090R DIO BAV99 350mW 75V SOT-23(PEC RoHS PANJIT, 0
610 411020026020R DIO BAV99-LF 350mW 70V SOT-23 (FEC)RoHS FRONTIER, 0
620 411020047210R DIO BAV70 85V SOT23 (PHILIPS) RoHS PHILIPS, 2 D106,D201,
620 411020047090R DIO BAV70, 70V SOT-23(PEC) ROHS PANJIT, 0
620 411020047020R DIO BAV70-LF, 70V SOT-23(FEC) ROHS FRONTIER, 0
630 432002312144R BEAD CORE SMD(0603)120Ω 300mA SBK160808 CHILISIN,TAI-TECH, 1 FB101,
640 432002360140R BEAD CORE SMD(0603)60Ω 600mA, GBK160808 CHILISIN,TAI-TECH, 2 FB102,FB105
650 410500068290R XSTR AP2305GN P-CH SOT23(APEC) RoHS APEC, 2 Q101,Q301
650 410500075270R XSTR AO3415 P-CH,SOT23(AOS) RoHS AOS, 0
XSTR AM2321P-T1-PF P-CH SOT23(ANALOG
650 410060018380R AP, 0
POW
Q104,Q105,Q
660 410500045210R XSTR PMBT3904 NPN 200MA,40V SOT23(PHILIP PHILIPS, 6
Q302,Q303,
57

Service Manual
XSTR MMBT3904LT1G NPN 200MA 40V
660 410500045140R ON SEMI, 0
SOT23(ON
660 410500045090R XSTR MMBT3904 NPN SOT-23(PANJIT)RoHS PANJIT, 0
670 410500046210R XSTR PMBT3906 PNP 200MA,40V SOT23(PHILIP PHILIPS, 2 Q107,Q108,
670 410500046090R XSTR MMBT3906 PNP SOT-23(PANJIT)RoHS PANJIT, 0
XSTR MMBT3906LT1G PNP 200mA 40V
670 410500046180R ON SEMI, 0
SOT23(ON
RB101,RB102
680 414916000050R RES SMD (0603) 0Ω J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 4
R164,
R102,R129,R
R151,R152,R
R171,R174,R
R179,R180,R
690 414918010350R RES SMD (0402) 10KΩ J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 36 R213,R217,R
R184,R161,R
R312,R314,R
R322,R108,R
R189,R195,R
700 414918000050R RES SMD (0402) 0Ω J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 3 R147,R105,R
R127,R128,R
710 414918047250R RES SMD (0402) 4.7KΩ J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 9 R188,R211,R
R157,
R109,R175,R
720 414918010450R RES SMD (0402)100KΩ J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 6
R308,R309,
730 414918027350R RES SMD (0402) 27KΩ J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 3 R107,R321,R
R117,R118,R
740 414918750910R RES SMD (0402) 75Ω F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 9 R115,R116,R
R124,
750 414918047150R RES SMD (0402) 470Ω J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R159,
R133,R134,R
760 414918010250R RES SMD (0402) 1KΩ J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 8
R155,R160,R
R131,R132,R
770 414918010150R RES SMD (0402) 100Ω J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 9 R209,R210,R
R158,
780 414918022250R RES SMD (0402) 2.2KΩ J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R135,R136,
790 414918390010R RES SMD (0402) 390Ω F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R144,
800 414916033150R RES SMD (0603) 330Ω J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R165,R168,
R201,R202,R
810 414918010050R RES SMD (0402) 10Ω J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 8
R205,R206,R
820 412000332130R IC AP1117D33LA 3.3V (ANACHIP) TO-252-3L, ANACHIP, 1 U101,
820 412000332830R IC AS1117R-3.3.TR-LF,TO-252(A1 SEMI)RoHS A1SEMI, 0
830 412000330020R IC LD1117AL-1.8V-A SOT223(UTC) RoHS UTC, 1 U102,
830 412000330830R IC AS1117L-1.8/TR-LF,SOT223(A1 SEMI)RoHS A1SEMI, 0
830 412000330070R IC AZ1117H-1.8 SOT223(AAC)RoHS BCD, 0
840 412000435481R IC AT24C02BN-SH-T 2K SOIC8(ATMEL)RoHS ATMEL, 2 U103,U201,
840 412000480280R IC M24C02-RMN6TP SO8(ST)RoHS ST, 0
840 412000480990R IC CAT24C02WI-TE13 SOIC-8(CATALYST)RoHS CATALYST, 0
850 412000653060R IC TSUMU58EHJ-LF-2 PQFP128(MSTAR)Rohs MSTAR, 1 U105,
860 412000224482R IC AT24C16BN-SH-T 16K(ATMEL) SOIC 8 ROHS ATMEL, 1 U106,
860 412000224280R IC M24C16-WMN6TP SO8 16K (ST) ROHS ST, 0
58

Service Manual
860 412000481990R IC CAT24C16WI-TE13 SOIC-8(CATALYST)RoHS CATALYST, 0
870 412000494190R IC SST25LF020A-33-4C-SAE SOIC8(SST)ROHS SST, 1 U108,
870 412000661620R IC MX25L2025MC-12G (MXIC)RoH MXIC, 0
870 412000494310R IC PM25LV020-100SCE SOIC8(PMC)RoHS PMC, 0
ZD102,ZD103
ZD105,ZD106
880 411130962950R ZENER 6.2V MMSZ5234B SOD-123(PANJIT)RoH PANJIT, 10
ZD203,ZD204
ZD202,
880 411121462950R ZENER 6.2V BZT52-C6V2 SOD-123(WILLAS)ROH WILLAS, 0
880 411131562950R ZENER 6.2V BZT52C6V2-7-F SOD-123(DIODES) DIODES, 0
890 491881200100H PCB,M/B ,2/OSP /FR4 /12,LP2236,HF EXPRESS,HSIANGKUO, 1
900 414918033450R RES SMD(0402) 330KΩ J,RT ROHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R303,
910 414918010550R RES SMD (0402) 1MΩ J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 4 R311,R146,R
FB308,FB309
920 432002312113R BEAD CORE SMD(0805)120Ω 3A PBY201209T-1 CHILISIN,MAGLAYERS,TAI-TECH, 4
FB311,FB312
930 432002330142R BEAD CORE SMD(0603)300Ω 2A PBY160808T-3 CHILISIN,TAI-TECH, 2 FB306,FB307
FB301,FB302
940 425000010720R CHOKE COM.MODE SMD 90Ω ,RoHS CHILISIN,FRONTIER,TAI-TECH, 5
FB304,FB305
R313,R315,R
960 414918015350R RES SMD (0402) 15KΩ J,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 5
R319,R197,
970 412000668390R IC USB2514-AEZG 36QFN(SMSC) SMSC, 1 U302,
FS310,FS311
980 432009300900R PTC 750mA SMD1206 1206L075YR,ROHS LITTELFUSE, 4
FS312,FS313
990 412000372020R IC LD1117AL-3.3V-A SOT-223(UTC RoHS UTC, 1 U301,
990 412000372830R IC AS1117L-3.3TR-LF,SOT223(A1S EMI)RoHS A1SEMI, 0
990 412000372070R IC AZ1117H-3.3 SOT-223(AAC)RoHS BCD, 0
990 412000598990H IC EC50117KBG 3.3V SOT223(E-CMOS) E-CMOS, 0
LABEL,BARCODE,BLANK,33x7mm, ROHS,FOR
1000 506140005700R HENGMINGDA,JIAYINMEI,KAIDA, 1
PCB
1010 511130002200R SOLDER PASTE,Sn96.5-Ag3.0-Cu0.5 ROHS TOMAS, 0.5
1010 511130002201R SOLDER PASTE,Sn96.5%Ag3.0%Cu0.5% TOMAS, 0
1010 511130002202R SOLDER PASTE,Sn95.5%Ag3.9%Cu0.6% TAMURA, 0
2. invert board BOM

ITEM P/N Description Supplier Usage Locatio
791922200A00R PCBA,INVERTER/B.,W/O SPK,LP2236-A19,ROHS
P1,P2,P
10 444179001010R CONN SPRING H/V 1P ROHS FOXCONN, 12 P6,P7,P
P11,P1
WFR 10P 2.0MM 90° SMD
20 430631100070R CVILUX,FCN,JOWLE, 1 CN1,
W/LOCK ROHS
C SMD(0805) Y5V 1UF/50V Z DARFON,MURATA,SAMSUNG,
30 419341050670R 1 C4,
ROHS TAIYO,TDK,WALSIN,YAGEO,
C SMD(0603) NPO
40 419304710560R MURATA,TAIYO,TDK,WALSIN,YAGEO, 4 C35,C3
470PF/50V,J,RoHS
59

Service Manual
C SMD(0805) X7R 2.2uF 16V K DARFON,MURATA,SAMSUNG,
50 419312254070R 3 C3,C11
RoHS TAIYO,TDK,WALSIN,YAGEO,
C SMD(0805) X5R 2.2uF/16V K, DARFON,MURATA,SAMSUNG,
50 419352254070R 0
RoHS TAIYO,TDK,WALSIN,YAGEO,
C SMD(0603) X7R 1000PF/50V K
60 419311020060R DARFON,TDK,WALSIN,YAGEO, 3 C14,C2
RoHS
C SMD(0603) X7R 2200PF/50V K C50,C5
70 419312220060R DARFON,TDK,WALSIN,YAGEO, 6
RoHS C56,C5
C SMD(1210) Y5V 10uF/35V Z
80 419341069680R MURATA,SAMSUNG,TDK, 5 C6,C7,
RoHS
CAP OS SVPD 47UF 35V M,125
90 421024700350R SANYO, 1 C5,
℃ SMD 10X13
C SMD(0603) X7R 0.1uF/16V,K
RoHS
C SMD(0603) NPO
110 419308200560R DARFON,TDK,WALSIN,YAGEO, 1 C1,
82PF/50V,J,RoHS
C SMD(0603) X7R 4700pF/25V K
RoHS
C SMD(0603) X7R 0.047uF/16V
K,RoHS
C SMD(0805) X7R 0.47uF/25V K
RoHS
C SMD(0603) X7R 0.033uF/50V K C49,C5
ROHS C55,C5
C SMD(0603) X7R 100PF/50V K C64,C6
RoHS REV:A C67,C6
C SMD(0805) X7R 0.1uF/50V K DARFON,MURATA,SAMSUNG,
180 419311040070R 2 C9,C29
RoHS REV:A TDK,WALSIN,YAGEO,
DIO BAV70-LF, 70V D7,D8,
190 411020047020R FRONTIER, 6
SOT-23(FEC) ROHS D11,D1
DIO BAV70, 70V SOT-23(PEC)
190 411020047090R PANJIT, 0
ROHS
D1,D13
200 411090046090R SCHTKY BAT54A, SOT-23(PEC) PANJIT, 7
D16,D1
SCHTKY BAT54A,
200 411090046040R MOSPEC, 0
SOT-23(MOSPEC)
SCHTKY BAT54A,-LF30V/200mA
200 411090046020R FRONTIER, 0
SOT-23(FEC)
60

Service Manual
D19,D2
DIO BAV99 350mW 70V
210 411020026210R PHILIPS, 12 D23,D2
SOT-23(PHI RoHS
D27,D2
DIO BAV99-LF 350mW 70V
210 411020026020R FRONTIER, 0
SOT-23 (FEC)RoHS
DIO BAV99 350mW 75V
210 411020026090R PANJIT, 0
SOT-23(PEC RoHS
XSTR
220 410050108290R AP9962AGH,N-CH,TO252(APEC) APEC, 4 Q1,Q2,
RoHS
XSTR
220 410050108430R P1504BDG,N-CH,TO252(NIKO) NIKO, 0
RoHS
XSTR RK7002 ESD N-C SOT-23
230 410500050230R ROHM, 2 Q5,Q6,
(ROHM)RoHS
XSTR 2N7002K ESD N-C
230 410500050120R VISHAY, 0
SOT-23, (VISHAY)RoH
XSTR 2N7002K01 ESD N-C
230 410500050212R PHILIPS, 0
SOT-23( PHILIPS)R
RES SMD (0603) 620KΩ
240 414916620310R TA-I,UNIOHM,WALSIN,YAGEO, 1 R6,
F,RT,RoHS
RES SMD (0603) 10KΩ J,RT R3,R17
250 414916010350R TA-I,UNIOHM,WALSIN,YAGEO, 6
RoHS R38,R3
R2,R10
RES SMD (0603) 100KΩ F,RT R22,R2
RoHS R26,R2
R30,R3
RES SMD (0603) 33KΩ F,RT
RoHS
R7,R68
RES SMD(0603) 30.1KΩ F,RT R71,R7
ROHS R75,R7
R79,
RES SMD (0603) 1MΩ J,RT
290 414916010550R TA-I,UNIOHM,WALSIN,YAGEO, 2 R12,R1
RoHS REV:A
RoHS
310 414908100910R RES SMD(0805)10Ω F,RT ROHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R18,
RES SMD (0805) 22Ω F,RT
RoHS
61

Service Manual
330 414916243310R TA-I,WALSIN,YAGEO, 1 R16,
ROHS
RES SMD (0603) 3.3M F RT
RoHS
RES SMD (0603) 5.1KΩ J,RT
RoHS
RoHS
RoHS REV:A
RES SMD (0603) 1.4KΩ R56,R5
F,RT,RoH S R62,R6
RES SMD (0603) 590Ω F,RT R57,R5
RoHS R63,R6
IC OZ9926AGN SOIC24(O2
400 412000689630R O2, 1 U1,
MICRO)RoHS
PCB,INV ,2/OSP /FR4
410 491882200100H EXPRESS,HSIANGKUO, 1
/12,LP2236,HF
DIO 1N4148W-F
420 411020046310R DIODES, 1 D2,
75V/0.15A(DIODES RoHS,SOD-
DIO 1N4148W
420 411020046090R PANJIT, 0
75V/0.15A(PEC)RoHS SOD-123
DIO MWS4148-G
420 411020046411R MMC, 0
75V/0.15A,SOD-123(MMC)RoHS
T1,T2,T
XFMR SW SMD EE13 P4 300mH
430 426000091270R DARFON,HUALON,LISHIN, 12 T6,T7,T
SPW-127 ROHS
T11,T1
440 505040209902R INVERT-MYALR,LP2236 Fuzhen(富准） 1
C37,C3
C SMD(0603) NPO 270PF/50V J
RoHS REV:A
C45,C4
RES SMD (0603) 3.3KΩ F,RT
460 414916330110R TA-I,WALSIN,YAGEO,UNIOHM 1 R44,
RoHS
470 414916360110R TA-I,WALSIN,YAGEO,UNIOHM 4 R45,R4
RoHS
RES SMD (0603) 4.3KΩ F,RT R48,R5
480 414916430110R TA-I,WALSIN,YAGEO,UNIOHM 5
RoHS R53,R5
490 414916390110R TA-I,WALSIN,YAGEO,UNIOHM 1 R49,
RoHS
500 414916470110R RES SMD (0603) 4.7KΩ F,RT TA-I,WALSIN,YAGEO,UNIOHM 1 R52,
62

Service Manual
RoHS
3. keypad BOM
ITEM P/N Description Supplier Usage Un
791921500000R PCBA,KEYPAD BOARD,LP2236-A19 ROHS
10 430602680280R SW,METAL DOME 180gf 5P ROHS FOXCONN,HUA-JIE, 1 PC
20 430631080191R WFR 8P 1.25MM 180° W/LOCK ROHS JOWLE, 1
20 430631080190R WFR 8P 1.25MM 180° W/LOCK ROHS FOXCONN 0 PC
PCBA,KEYPAD BOARD,SMT,LP2236-A19
30 791921540000R 1 PC
ROHS

PCBA,KEYPAD BOARD,SMT,LP2236-A19
791921540000R
ROHS
10 411070093500R LED SMD YB KPTB-1612FX151-SZ(Kingbright) KINGBRIGHT, 1 PC
LED SMD YB
10 411070094500R HONGTONG, 0 PC
HTL-19-22UYUBC/TR8(HongTong)R
20 491881500000H PCB,K/P ,2/ENIG/FR4 /08,LP2236,HF EXPRESS,HSIANGKUO, 1 PC
4. USB convert board BOM

PCBA,CONVERT/B(USB) W/O
791860300000R
SPK,LP1931,ROHS
10 430631080210R WFR 8P 2.0MM 90° W/LOCK ROHS FOXCONN,JOWLE, 1 PC
CAP SD 100uF 16V M,105
20 420421010481R CAPXON,SU'SCON,TEAPO, 2 PC
℃,CF,5x11,RoHS,2.
CON USB A,R/A,4
30 442849001060R TEKCON,FOXCONN, 2 PC
POS,UB11123-4R1-4F,RoHS
SOLDER
40 511130001200R TOMAS, 0.698 G
BAR,Sn96.5/Ag3.0/Cu0.5/Ni0.06/Ge0
60 491660300100H PCB,CNV-U,1/OSP /CEM1/12,LP1931 HF HSIANGKUO,TATCHUN, 1 PC
6. Assembly BOM
ITEM P/N Description Supplier
822236A1D010R 2209WAf/H736H/LP2236-A19/LGD/DAO
FOXCONN,HOTRON,JVE,廣
10 453010100320R CABLE D-SUB 15P MALE 6FT BLACK/BLUE AB 8
宇,
FOXCONN,HOTRON,JVE,廣
20 453030300440R CABLE DVI-D 18+1P MALE 1.8M BLACK ROHS
宇,
63

Service Manual
FOXCONN,GREATLANE,廣
30 453030300230R CABLE USB 2.0 2M BLACK RoHS
宇,
40 453070800150R PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx FOXCONN,I-SHENG,
50 7140793A2000R ASSY,FINAL(B)W/OSPK,LP2236-A19(2209WAf)
60 713100009900R ASSY, PACKAGE, PACK, DAO,LP2236

713100009900R ASSY, PACKAGE, PACK, DAO,LP2236
10 506140006500R LABEL,BARCODE, LP2236 高綺,鍵升,
20 506250027700R LABEL,AGENCY,TCO 03 LP2236 高綺,鍵升,
30 506431005200R FILM,SCREEN,PROTECTION,PRINTED,LE22E0 柏興,鴻旺,
40 506380001400R TAPE 3M-897 12x45000mm 久威,矽威,
50 506280008210R POSTER,QUICK SETUP,WEST, LP2236 裕同,鴻達,
60 703500010000R KIT,ACCESSORY, DOC, DAO, LP2236 裕同,鴻達,
70 506120300060R BAG, PLASTIC,L670*W440mm(PRINTED), LE22E 柏興,鴻旺,
80 506120301810R BAG,EPE+HDPE,L800/400XW450MM,LP1X03 柏興,鴻旺,
90 506060012720R Cushion for Stand,LP2236 東揚,
100 506020029700R CARTON,DELL(WWW), LP2236 佳藝,美盈森,
110 506060012710R CUSHION TOP,LP2236 東揚,
120 506060012700R CUSHION BOTTOM,LP2236 東揚,
130 506340004700R LABEL BLANK 101X50mm DELL EMEA CARTON 高綺,鍵升,
140 506380002622R TAPE, WRAPPING TYPE PRINTED(DELL), BLACK 佳普森,
150 713010005602R ASSY PACK,40HQ,LP2236
150 713010005600R ASSY PACK,20STD,LP2236
150 713010005601R ASSY PACK,40STD,LP2236
150 713010005603R ASSY PACK,AIR/JAPAN CARGO (20STD),LP2236
150 713010005604R ASSY PACK,AIR/JAPAN CARGO(40STD),LP2236

7140793A2000R ASSY,FINAL(B)W/OSPK,LP2236-A19(2209WAf)
10 509212103500R SCREW,F,CROSS,T.T-2*3,BLK 高億,
20 509116610510R SCREW,P,CROSS,M4*10,BLACK-NL(NYLOK) 立侑,高億,
30 506250024300R LABEL, CARD,LP1931 MMP,
40 714050019001R ASSY BACK COVER ,LP2236,SILVER MMP,
50 714020016000R ASSY STAND ,LP2236 銘異,
60 714030020200R ASSY,FRONT,BEZEL,LP2236,Black MMP,
70 7140893A2000R ASSY,PANEL,W/OSPK,LP2236-A19(2209WAf)

713010005600R ASSY PACK,20STD,LP2236
64

Service Manual
10 506432000600R SLIP SHEET,L1370xW880mm,LE1711 SUNSTREAM,
20 506037011200R CARDBOARD,COVER,L1224xW880xH100xT3mm,LP2 佳藝,美盈森,
30 506039006900R CORNER PAPER 950x50x50xT3mm LE1712 佳藝,金惠,
40 506039006200R CORNER PAPER 1100x50x50xT3mm LE1513 ROH 佳藝,金惠,
50 506431000300R FILM,PE 500mmx900M ROHS 三輝,柏興,
60 506380002612R TAPE,WRAPPING TYPE,50Mx82mm 佳普森,

713010005601R ASSY PACK,40STD,LP2236
30 506039006900R CORNER PAPER 950x50x50xT3mm LE1712 佳藝,金惠,

713010005602R ASSY PACK,40HQ,LP2236
40 506039010000R CORNER PAPER, L1350X50X50XT3MM,LP1716 金惠,

713010005603R ASSY PACK,AIR/JAPAN CARGO (20STD),LP2236
10 506150006900R PALLET L1284xW914xH120mm LE1746 實習工廠,
30 506039008700R CORNER PAPER 900x50x50xT3mm LP1704 金惠,
40 506039001400R CORNER PAPER 200x50x50mm ROHS 佳藝,金惠,
60 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN,

713010005604R ASSY PACK,AIR/JAPAN CARGO(40STD),LP2236
10 506150006900R PALLET L1284xW914xH120mm LE1746 實習工廠,
30 506039008700R CORNER PAPER 900x50x50xT3mm LP1704 金惠,
65

Service Manual
40 506039001400R CORNER PAPER 200x50x50mm ROHS 佳藝,金惠,
60 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN,

714030020200R ASSY,FRONT,BEZEL,LP2236,Black
10 501010221100R FRONT,BEZEL,LP2236,Black MMP,
20 750020200600R SUB-BUTTON,LP2236,BLACK PCM,
30 501120109500R POWER BUTTON LENS, LP2236, DARK SMOKED HANHAI,
40 501110200400R LOGO PLATE DELL UX383 LE1963 DEMETER,

714050019001R ASSY BACK COVER ,LP2236,SILVER
10 750030200500R SUB-BACK COVER ,LP2236,Black PCM,
20 501010221102R Mid Frame,LP2236,Silver MMP,
30 501030210502R release-button,LE22F4 MMP,
40 502210100400R KENSINGTON LOCK LE1963 MMP,
50 509012305000R SCREW,I,CROSS,T.T-3*5,ZN-Cc, 鴻益進,
60 501110201100R BACK COVER LOGO,LP2236,Silver MMP,

7140893A2000R ASSY,PANEL,W/OSPK,LP2236-A19(2209WAf)
10 631102220560RD LCP 22"LM220WE4-SLB1(A)(LGD)ROHS
20 430303002030R HRN LVDS FFC 30P 82MM
30 430300802130R HRN ASSY 2x4P to 8P 322mm UL1571#28
40 701000011200R ASSY CHASSIS-BTM, LP2236
50 701000011201R ASSY CHASSIS-TOP,LP2236
60 502090313403R USB-COVER,LP2236
70 502090313404R INVERT-CHASSIS,LP2236
80 505040209900R BTM-CHASSIS-MYLAR,LP2236
90 505040209901R TOP-CHASSIS-MYLAR,LP2236
100 509000001000R BOLT,#4-40x12.5,Ni ROHS
110 509016304200R SCREW,I,CROSS,M3*4,Zn-CcROHS
120 509016306200R SCREW,I,CROSS,M3*6,Zn-Cc
130 509146306202R SCREW,P,CROSS,W/WAS(7.8),M3*6,Zn-Cc
140 509146610200R SCREW,P,CROSS,W/WAS(8),M2*4,Zn-Cc
150 791921200A00R PCBA,MAIN BOARD,W/O SPK,LP2236-A19,ROHS
160 791922200A00R PCBA,INVERTER/B.,W/O SPK,LP2236-A19,ROHS
170 791921500000R PCBA,KEYPAD BOARD,LP2236-A19 ROHS
66

Service Manual
180 791860300000R PCBA,CONVERT/B(USB) W/O SPK,LP1931,ROHS
190 511110000580R SILICONE PAD,25*15*0.8mm,
200 512004001200R SPACER SUPPORT H4.0
210 506381001710R TAPE,ACE,W28*L15mm,LE1971
220 503010006300R RUBBER FOR INVERT,LP2236

701000011200R ASSY CHASSIS-BTM, LP2236
10 502090313400R CHASSIS-BTM,LP2236
20 502090313401R CHASSIS-SUPPORT,LP2236
30 502120400300R CLIP EMI GND(3) LP1702

701000011201R ASSY CHASSIS-TOP,LP2236
10 502090313402R CHASSIS-TOP,LP2236
20 502020306000R fix-plate-left,LE19E6
30 502020306010R fix-plate-right,LE19E6
40 502040500100R slide,LE22F4
50 504010000300R SPRING Φ0.5*D5*H17
60 509112304100R SCREW BTP3x4C3UC,ROHS

750020200600R SUB-BUTTON,LP2236,BLACK
10 501030211500R BUTTON,LP2236,BACK MMP,

750030200500R SUB-BACK COVER ,LP2236,Black
10 501020225000R BACK COVER ,LP2236,Black MMP,
67

Service Manual
Attachment 2- Schematic
1. Main board schematic
2209Wa History
Title page
initial
1.0 Top level 1
2.0 contents 2
3.0 VGA input 3
4.0 DVI input 4
5.0 Scalar 5
6.0 USB 6
7.0 DC input 7
8.0 power 8
Title
contents
Size Document Number Rev
A4 <Doc> V01
Date: Wednesday , September 10, 2008 Sheet 2 of 8
68

Service Manual
3.0 VGA input 5.0 scalar
RED+ RED+ Title

RED- RED- Top level
GREEN+ GREEN+
GREEN- GREEN- Size Document Number
SOG SOG A4 <Doc>
BLUE+ BLUE+
BLUE- BLUE- Date: Saturday , May 17, 2008 Sheet 1
VGA_DET VGA_DET 6.0 USB
HSY NC HSY NC
VSY NC VSY NC USB_EN USB_EN
DDC_SCL_VGA DDC_SCL_VGA
DDC_SDA_VGA DDC_SDA_VGA USB_DET USB_DET
WP_EDID_VGA WP_EDID_VGA
6.0 USB
3.0 VGA input
4.0 DVI input 7.0 DC input
WP_EDID_DVI WP_EDID_DVI
DVI_DET DVI_DET
CCFL_ENABLE CCFL_ENABLE
RX0+ Rx0+
RX0- RX0- Audio_EN Audio_EN
RX1+ RX1+
Audio_on_off
RX1- RX1-
VCC_1.8V
RX2+ RX2+
RX2- RX2- PANEL_ENABLE PANEL_ENABLE
RXC+ RXC+ VLCD VLCD

RXC- RXC-
HPD_CTRL HPD_CTRL 7.0 DC input
DDC_SCL_DVI DDC_SCL_DVI VCC_1.8V

DDC_SDA_DVI DDC_SDA_DVI
4.0 DVI input PWR24V_ON

BRIGHTNESS
PWR_DCR
Audio_DET
PWR_sav e
5.0 scalar
8.0 power
PWR_sav e Audio_DET
PWR_DCR BRIGHTNESS
PWR24V_ON
Audio_on_of f
CCFL_ON_OFF
8.0 power
69

Service Manual
CN102
Note 1
DZ11AA1-H5W6-4F
11 1 R RB101 0 R114 75 1% C113 0.047u/16V
6 R0603
12 2 G RB102 0 R115 75 1% C114 0.047u/16V
7 R0603
13 3 B RB103 0 R116 75 1% C115 0.047u/16V
75 1%
8 R0603
75 1%
75 1%
14 4 VGA5V
9 C116 C117 C118
15 5 NC NC NC
10
R117
R118
R119
R122 75 1% C119 0.047u/16V
16
17
R123 75 1% C120 0.047u/16V
R124 75 1% C121 0.047u/16V
VGA_DET
GND D102 D103 D104 D105 +5V_PI VGA5V
3
BAV99 BAV99 BAV99 BAV99
C126 0.1/16V
2 1 2 1 2 1 2 1 +5V_PI
6V2
C127
C122 C174 C175 C125
1
ZD102
0.1/16V/NC
0.1/16V 0.1/16V 0.1/16V 0.1/16V
3
GND R127 R128 R129
4K7 4K7 10K
GND
VGA_SCL R131 100

VGA_SDA R132 100
FB101
120Ω
R133 1K
HSY NC 5
R134 1K
VSY NC 5
33p/50V
33p/50V
Note 2
2K2
2K2
6V2
6V2
6V2
6V2
ZD103 C131 C132
ZD104
ZD105
ZD106
C129
C130
NC NC
R135
R136
GND GND
Note:
1. R0603 package for Bead. C116,C117,C118 10pF are reserved for EMI or performance Title
issue.
VGA
Size Document Number Rev
2. C131,C132 27P are reserved for tuning performance issue. A4 <Doc>
Date: Monday , August 04, 2008 Sheet 3 of 8
70

Service Manual
FB202 FB203 FB204 FB205
DVI_RX2- 4 3 RX2- DVI_RX1- 4 3 RX1- DVI_RX0- 4 3 RX0- DVI_RXC+ 1 2
DVI_RX2+ 1 2 RX2+ DVI_RX1+ 1 2 RX1+ DVI_RX0+ 1 2 RX0+ DVI_RXC- 4 3
COMM CHOCK COMM CHOCK COMM CHOCK COMM CHOCK

NOTE:
CN201 FB202 FB203 FB204 FB205 must be co-layed with R201 R202~R208,mount resistor at this phase
DVI-D_CON
+5V_PI DVI5V
1 DVI_RX2- R201 10
RX2- DVI_RX2+ RX2- 5
2 R202 10
RX2+ RX2+ 5
3
GND
1
9 DVI_RX1- R203 10
10 R204 10 BAV70
RX1+ RX1+ 5
19
GND 17 DVI_RX0- R205 10
18 R206 10
3
RX0+ RX0+ 5
22 R211 R212 R213
GND 23 DVI_RXC+ R207 10 U201
RXC+ 5 4K7 4K7 10K
RXC+ 24 DVI_RXC- R208 10 AT24C02
RXC- RXC- 5
8
7
6 DVI_SCL R209 100 6
SCL 7 DVI_SDA R210 100 5
SDA 8
VS
WP_EDID_DVI
DDC_SCL_DVI
14
5V DDC_SDA_DVI
15 DVI_DET DVI_DET
GND DVI_DET
16 HPD_DVI HPD_DVI
HP 4
RX4- 5
RX4+ 11 DVI5V
GND 12 D202 D204 D206 D208 D210
RX3-
3
13 BAV99 BAV99 BAV99 BAV99 BAV99
RX3+ 20 2 1 2 1 2 1 2 1 2 1
RX5- 21
0.1/16V
RX5+ DVI5V
6V2/NC
C202 0.1/16V
C213 0.1/16V
C211
6V2
6V2
6V2
DVI5V R217 10K
0.1/16V
HPD_DVI
ZD201
ZD203
ZD204
ZD202
C212
D203 D205 D207 D209
3
BAV99 BAV99 BAV99 BAV99 R219
3
2 1 2 1 2 1 2 1
4K7
Q201 1
PMBT3904
+5V_PI
C207 C208 C209 C210
HDCP Fu
2
0.1/16V 0.1/16V 0.1/16V 0.1/16V
GND
GND
71

Service Manual
Note:
1. Each bypass capacitor (0.1u/16V) must be respectively
closed to pin that is DC power input of scaler IC.
VCC_3.3V
VCC_3.3V
VDDP_33 AVDD_33 AVDD_33 VDDC_18 AVDD_18 VDDP_33
Note
FB102
10K
10K
10K
10K
10K
10K
10K
10K
10K
10K
NC
60Ω
C154 0.1/16V
C155 0.1/16V
C156 0.1/16V
C159 0.1/16V
C160 0.1/16V
C133 0.1/16V
C134 0.1/16V
C135 0.1/16V
C136 0.1/16V
C137 0.1/16V
C138 0.1/16V
C139 0.1/16V
C149 0.1/16V
C161 0.1/16V
C141 0.1/16V
104
126
114
107
112
103
14
20
53
74
21
58
54
40
59
87
60
65
66
71
8
C150 +
47u/16V
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
AVDD_33
AVDD_33
AVDD_33
AVDD_18
VCTRL
VDDC
VDDC
VDDC
VDDC
R150
R151
R152
R171
R172
R184
R174
R140
R220
R179
R139
28
3 RED+ RIN0P
3 RED- 27 119 R153 1K
25 RIN0M GPIO_P00/SAR0 120 R154 1K
3 GREEN+ GIN0P GPIO_P01/SAR1
GND 24 121 R155 1K
3 GREEN- GIN0M GPIO_P02/SAR2
3 SOG R159 470 C152 0.047u/16V 26 122
VDDC_18 AVDD_18 23 SOGIN0 GPIO_P03/SAR3 123
3 BLUE+ BIN0P GPIO_P06
FB105 22 124
3 BLUE- BIN0M GPIO_P07
3 HSY NC 32 2 R157 4.7K
7 VCC_1.8V HSY NC0 GPIO_P14/PWM0
60Ω 3 VSY NC 33
34 VSY NC0 3 R158
C142 + 3 DDC_SDA_VGA 35 DDCA_SDA/RS232_TX GPIO_P15 4 R125 1K
47u/16V C143 C144 C145 C146 C147 3 DDC_SCL_VGA DDCA_SCL/RS232_RX GPIO_P16 36 R160 1K
0.1/16V 0.1/16V 0.1/16V 0.1/16V 0.1/16V 9 GPIO_P22/PWM1 48
4 RX2+ RX2P GPIO_P44
4 RX2- 10
12 RX2N 50
4 RX1+ RX1P GPIO42
4 RX1- 13 51
15 RX1N GPIO_P24/PWM2
4 Rx0+ RX0P
GND 16 73 R182 100
4 RX0- RX0N GPIO_P04/PWM3
4 RXC+ 18 109
19 RXCKP GPIO_P25/PWM3 125 R188
4 RXC- RXCKN GPIO_P13/PWM2
5
4 DDC_SDA_DVI DDCD_SDA
6 39
4 DDC_SCL_DVI DDCD_SCL I2C_MCL/GPIO_P10 38
AVDD_33 R144 7 I2C_MDA/GPIO_P11
390 1%
VCC_3.3V REXT 49 R216 1K
31 GPIO_P43 47
REFP GPIO_P45
C148 46
1u/16V 30 GPIO_P46 45
R161 VCC_3.3V REFM GPIO_P47
10K
C165 U105
0.1/16V
TSUMU58EHJ-LF-2/3
R189 R190
SELECT_KEY R164 0 SELECT 10K/NC 10K GND U108 100 RXO0-
R0603 8 2 SDO 41 LVB0M 99 RXO0+
7 VCC SO 1 SCZ 42 SDO LVB0P 98 RXO1-
WP_FW 3 HOLD# CS# 6 SCK 43 CSZ LVB1M 97 RXO1+
4 WP# SCK 5 SDI 44 SCK LVB1P 96 RXO2-
+5V_PI GND SI SDI LVB2M 95 RXO2+
R192 PM25LV010A-100SCE LVB2P
10K 94 RXOC-
108 LVBCKM 93 RXOC+
RST LVBCKP 92 RXO3-
LVB3M 91 RXO3+
R177 C157 22p/50V R147 0 128 LVB3P 86 RXE0-
XIN LVA0M
2
10K +5V_PI 85 RXE0+
Q107 1 LED_B_EN GND X101 R146 LVA0P
PMBT3906 14.31818MHz 84 RXE1-
R166 10K 1M 127 LVA1M 83 RXE1+
C164 1u/16V XOUT LVA1P
3
R165 C158 22p/50V 82 RXE2-
330 102 LVA2M 81 RXE2+
BY PASS LVA2P
100K
R0603 C153 0.1/16V 80 RXEC-
LED_B VDDP_33 LVACKM 79 RXEC+
LVACKP
GPIO_P26/PWM0
GPIO_P27/PWM1
78 RXE3-
R149 10K/NC 37 LVA3M 77 RXE3+
MODE LVA3P
LVB4M/NC
10K
R175
LVB4P/NC
+5V_PI
GPO_P42
GPIO_02
GPIO_01
GPIO_00
GPIO_06
GPIO_07
GPIO_08
GPIO_09
GPIO_10
GPO_43
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
NC
NC
NC
R180
R176
101
105
106
113
110
111
115
116
117
118
7 VLCD
11
17
29
52
72
88
68
69
63
62
75
76
89
90
57
56
55
61
64
70
67
10K
1
Q108 1 LED_A_EN
PMBT3906
R169 10K R110 NC
GND
3
PWR_sav e 8
R168 GND
560
USB_DET 6
R0603 VCC_3.3V
LED_A
USB_EN 6
R163 10K R162 100
PWR24V_ON 8
CN104 on
2x4P 2.0mm
CON--CLX-CI0108P1VDL
1 MENU KEY KEY 1 off
2 ENTER&PLUS ADC_KEY1 PWR24V_ON
3 EXIT/MINUS ADC_KEY2 VCC_3.3V
4 SELECT KEY SELECT_KEY
5 LED BLUE LED_B
6
7 LED AMBER LED_A
8 POWER KEY 2 R138 R137 C140 USB_DET USB_EN
0.1/16V
C173 0.1/16V
4K7 4K7 0.1/16V
C167 0.1/16V
C169 0.1/16V
C170 0.1/16V
C171 0.1/16V
C172 0.1/16V
U106
8 1 Heigh Low
WP_OSD 7 VCC A0 2
To Keypad WP A1
SCL_OSD R142 100 6 3
Board SCL A2
C168
SDA_OSD R143 100 5 4 Low Heigh
SDA GND
AT24C16BN
GND
GND
Title
scalar
Size Document Number
Custom<Doc>
Date: Wednesday , September 10, 2
72

Service Manual
+5V_PI
5V_USB USB_3.3V
Q301 U301 LD1117AL-3.3V

AP2305GN FB306
+5V_PI 2 3 3 2
VIN VOUT
ADJ
FB301 4
P301 DM 1 2 DM0 PAD C305 C306
27K R321
10K R301
C304 +
1
DP DP0 0.1/16V
0.1u/16V
1 4 3 C303
1
2 DM 0.1/16V 47u/16V
3
3 DP COMM CHOCK
NC
NC
4
4
R322
10K USB_DET 5
3
UC11123-LK1
5
USB_DET USB_EN 1 S S
5 USB_EN Q302
EP305
EP301
3
C314 R302 10K PMBT3904
1 Heigh Low
2
Q303
0.1/16V PMBT3904
Low Heigh
2
S
S
FB308 120Ω 3A
S U302 PWR2
R304 100K USB2514QFN36 R310 12K 2M
27 35 C307 2P
VBUS_DET RBIAS
NC
NC
+ C309
DM0 30 2 DD1P
USB_3.3V R303 USBUP_DM USBDN1_DP 47u/16V
DP0 31 1 DD1M 0.1/16V
USBUP_DP USBDN1_DM
S
OVR_P1 DD2P
EP304
EP306
330K 13 4
OVR_P2 17 OCS1 USBDN2_DP
OVR_P3 19 OCS2 3 DD2M
OVR_P4 21 OCS3 USBDN2_DM
S S
R305 0 OCS4 7 DD3P
28 USBDN3_DP
S
R306 27K LOCAL_PWR/NON_REM0/SUSP_IND 6 DD3M FB309 120Ω3A
26 USBDN3_DM PWR1
RESET 9 DD4P 1M
11 USBDN4_DP C308 1P
C315 TEST 8 DD4M + C310
C323 22p/50V 33 USBDN4_DM
XTAL1/CLKIN 12 47u/16V 0.1/16V
PRTPWR1
NC
NC
1u/16V
R311 X301 16
PRTPWR2 FB307
+3.3V_2514 1M 24.000MHz 18 300Ω 2A
S S S
SMSC2514 QFN36Pin PRTPWR3
EP302
EP303
32 20
C324 22p/50V XTAL2/CLKIN_EN PRTPWR4
S
23 22 R307 100K C311 0.1/16V
VDD33(IO) SDA/SMBDATA/NON_REM1
15 24 R308 100K
VDD33(REG) SCL/SMBCLK/CFG_SEL0 FB302
5 25 R309 100K DD1P 1 2 1P
VDDA33 HS_IND/CFG_SEL1
S
C316
C317
10 34 DD1M 4 3 1M
VDDA33 VDDPLL18
29 14
VDDA33 VDDCR18
C312
C313
S COMM CHOCK
C322
0.1/16V
0.1/16V
36 37
VDDPLLREF/VDDA33 VSS(FLAG)
C318
C319
C320
C321
+ + FB303
DD2P
4.7u/16V
4.7u/16V
+ 1 2 2P
4.7u/16V
S S
0.1/16V
0.1/16V
0.1/16V
0.1/16V
DD2M 4 3 2M
COMM CHOCK
PWR3
S S 3M
FB304 3P
DD3P 1 2 3P
5V_USB 5V_USB 5V_USB 5V_USB
DD3M 4 3 3M 4P
4M
FS310 FS311 FS312 FS313 COMM CHOCK PWR4
PWR1 PWR2 PWR3 PWR4
NC
NC
6V/0.75A 6V/0.75A 6V/0.75A
6V/0.75A
FB305
R312
R314
R316
R318
10K
10K
10K
10K
DD4M 1 2 4M
EP308
DD4P 4 3 4P
EP307
OVR_P1 OVR_P2 OVR_P3 C325 OVR_P4 C326
COMM CHOCK
0.1/16V 0.1/16V
15K
15K
15K
15K
R313
R315
R317
R319
S S
S S S S
Title
USB
Custom<Doc>
Date: Tuesday , September 16, 2008
73

Service Manual
+5V_PI
VCC_3.3V VCC_3.3V
U102
U101 LD1117AL-1.8V
+5V_PI AP1084K33LA 3 2
VIN VOUT VCC_1.8V 5
3 2
ADJ
VIN VOUT 4
ADJ
4 PAD
PAD
ZD107 6V2/NC
C106 +
0.1/16V C103
1
C111 47u/16V C107
1
C104 + 0.1/16V/NC
0.1/16V C102
100u/16V
0.1/16V
GND
GND
GND
+5V_PI
Q101
Audio_DET Audio_EN VCC_3.3V AP2305GN
2 3
Height Low
C108
100u/16V
R197 0.1/16V R109
1
Low Height 100K
on
0.1/16V
15K
Audio_on_of f +
Audio_on_of f 8 off GND
R196
C109
R107
3
NC
C110
27K
1 Q105 1
5 Audio_EN 5 PANEL_ENABLE Q104
PMBT3904 PMBT3904
R195
10K + R108
2
C112 10K
4.7u/16V
GND
Note: See Table 1.

GND
VCC_3.3V GND
R102 R103
off 10K
10K R105 Table 1
on 0 CCFL_ON_OFF
CCFL_ON_OFF 8 Backlight On/Off Component Mount No Connection
R104
High Enable R104,
3
NC R102,R103,R106,R105,Q103
1 Q103
5 CCFL_ENABLE Low Enable R103,R104,R105 R102,,Q103,R106
PMBT3904
R106
10K
2
Title
GND
DC input
A4 <Doc>
Date: Tuesday , September 16, 2008 Sheet
74

Service Manual
D858 1N4007
D859 1N4007
D856 RT851 C858 R856
+24V_DC
D850
IN5406 1000p/1KV 20 3W L854
2
GBU8-06 SCK053 D853 CHK BR3X20/ 2.2uH
1
L853 L855 L856 D860 L857 L858 FR850 2
4 - + 1 2 12 1 2 1 2 1VBUS 3
.6
Bead Bead Bead Bead 0.2R 1W SRF10-20CT
FR851 600V/8A D854 + C862 + C863 + C864 + C865
L852 CHK-110 11mH 0.2R 1W C867 C868 R855 C855 ZD851 1 470u/35V 470u/35V 470u/35V 470u/35V
C874 2.2nF/1KV 2.2nF/1KV 75K 3W 10nF/400V P6KE350A T850 2
3
4 3 + C854 3
1uF/ 450V 120u/450V SPW-128 PQ3220
10
EMI Shield SRF10-20CT C861
2
10nF/ 50V
1 2 R871 R831
1
Q853
FQPF12N60C
C882
100p/1KV R981
499K
R985
499K D851
5
. 11
10
R885 1/4W 1/4W FR30-10-LF

1M2 300K 10K
3
VZ850 R870 1/4W 1/4W
2 1 R982 R986 2
499K 499K
OPTION 1/4W 1/4W
RT850 0.22R/ 3W 1% R872 R832 R984 R983 1
3R/7A 1M2 300K L859
1/4W 1/4W 499K 499K Bead
C853
0.33uF X2
C887
1000p/ 400V
C888
1000p/400V R873 R833

R875
20
1/4W
R988
1/4W
R987 . 8
7
Y1 Y1 1/4W 2
1M2 300K 499K 499K
1/4W 1/4W 1/4W 1/4W
R893 R894
R874 R834 R989
374K 374K C811 Q850
2
1/4W 1/4W 1M2 300K 4700p/ 50V 15.8K 1%
C812 1uF/50V 1/4W 1/4W SPA11N80C3
1 C881
R891 R892 U850 100p/1KV
SG6901A Signal GND Signal GND
374K 374K R813 R886
3
1/4W 1/4W 1 20 10K
VRMS IAC
68K
C885 C886 Signal GND R814 C818 10uF/25V
2 19
RI VEA R854
1000p/400V 1000p/400V 24K 1%
Y1 Y1 C819 100p/ 50V 0402 Signal GND 20 R853
3 18 1/4W 0.12R 2W
OTP FBPFC
C813 4700p/ 50V 0402 R822
L851CHK-110 11mH C814 R821 C817
R816 4 17 46.4K 4700p/50V 24K 1%
4 3 IEA OVP
1K 1% 1000p/50V
R817 0402 0402
5 16 VDD R859
IPFC RANGE Signal GND 1K5 1%
2K7 1% 1/4W
1 2 0402 C815 Open 0402
6 15 R858 +24V
IMP VDD 7
C822 10K I850 R878
R818 2K7 1% 0402 1uF/50V 4 1 2K2 1%
C871
C852 R819 Open 7 14 OPEN +24V
0.33uF X2 0402 ISENSE OPFC 3 2 R860
86.6K 1%
R824 LTV817M
8 13 R864 C872 R967
FBPWM GND 20K 1%
100 1%
C850 C851 C820
4700p/ 50V 4K7 1% 0. 047/50V
0402 9 12 I 851
2200p/400V 2200p/400V IPWM OPWM
Y1 Y1 C821 TL431
Signal GND 2200p/ 50V R863
0402 10 11 C967 R969
AGND SS 10K 1% 1nF/50V 6.8K 1%
R829 R825
F850 10.5K 1% 200 1% C816
0. 01/50V
3.15A 250V
2
Signal GND Signal GND
VDD
+12V
1 3
Q930
AP9972
4 3
CN850
FR950
HF-301PCB 7MM VBUS
0.2R 1W R930 C930 R936
1
C955 100R 3W 1nF/1KV +24V Q931 10K + C932
1
R931 PMBT2907A ZD930 470u/25V R938 L930
4700p/400V 2 3 GDZ20B 20V 39. 2K
R837 R838 R839 D930 5A/150V 0402
T900 1K
SPW-129 PQ2620 1/4W D932
20K 1/4W 20K 1/4W 20K 1/4W D931 5A/150V R932 1N4148
2
D951 + C931
1 . 7 470u/35V CHK-091
FR10-10-LF 20K 1%
Q951 C960 R960 0402 R933
R835 D953 MMBT4401 3 2200p/100V 10R 2W 10K
VDD 20K 2 3 9 R937 C935
1/4W L953 10K 1nF/50V X7R
Q953 1N4148 8 D960 CHK-077/2.2uH +5V_PI HIGH ON I930
3
PMBT2907A C956 + C957 R953 1 R935
2 3 R836 D952 2 1 Q932 TL431 R939
1
7 Audio_on_of f
20K 0.01/50V 10u/50V ER104 3 10K
1/4W 10K 12 Audio_on_off 10K 0402 MMBT4401 0402
+5V_PI 5 11 SRF10-100CT C964 R934
2
R940 ZD951 C952 C951 10 D961 C962 C963 C936
1
GDZ20B 20V 47uF/ 50V 104p/50V

6
. 1
2 330uF/16V 330uF/16V 470uF/25V
1000p/50V
0402
1M
0402
20K 1% R942 Q950 . 3 OS-CON SEP OS-CON SEP
2
0402 R941 2SK3265
6
10K 470 R956 SRF10-100CT C961
8 5 1 10nF/50V
VDD
HV GATE
I952 R943 47R C860
4 1 2200p/400V R963
3
1K 1% C958 R964 +5V_PI +24V_DC +12V
100p/1KV 10. 5K 1%
R951
3 2 U950 10K
7 1 330 1% R971 R972 R973
NC RT C969
LTV817M I 950 OVP
R958 4 1 +5V_PI OPTION 200 1% 200 1% 200 1%
LD7575
100K 1% R968 0. 1/50V R976
3 2 2K2 1% 22K 1%
R957 R965 C968 R978 ZD971 ZD972 ZD973
GND
2 3 LTV817M Q960 10K 1%
FB SNESE
3
RK7002 GDZ5. 6B GDZ30A GDZ16A
470R 10K 0. 047/50V
3
Q860 I951 1 Note:

4
R898 PWR_sav e 5
HIGH ON C954 R959 Q971
1 C953 0R51 2W TL431 R962 1)All Resistor wit
2
5 PWR24V_ON
10K 1% C978 R977 C977
10K 0402 RK7002 1000p/50V 470p/50V (18K/Power 1nF/50V 100K 1% 1nF/50V SFOR3G42
power rating 1/8W
2
R897 0402 Saving)

C897 R970 C891
1uF/10V 1M
0402 1K 1% 0.01/25V
Title
power
A2 <Doc>
Date: Tuesday , September 16
E:\2209WA\proto1\
proto3\dell2209wa 0821.pdf
2. Invert board schematic
75

Service Manual
2
+ C5 C9 C6 R33
47u/35V 0.1uF/50V 10u/35V 22R 0805 Q1
HDR1 1 AP9962 C12
D1 R37 C35 10u/35V
3
BAT54A 10K 0603 470PF 0603
1 C13
3 LX1
VREF VA
CN1 2
2
1 +24V 10u/35V
VIN 2 R34
VIN
+24V
3 +24V 22R 0805 Q2
VIN 4 C24 C23 LDR1 1 AP9962
GND 5 0.47uF/25V X7R 0805 0.47uF/25V X7R 0805
GND 6
GND 7 U1 R38 C36
3
DIM 8 R18 R9 10K 0603 470PF 0603
ENA 9 R1 LX2 1 24 LX1 10R 0805 750K 0603
GND 10 NC LX2 LX1
DCR HDR2 2 23 HDR1
CON10PIN HDR2 HDR1 R35
R4 R3 3 22 22R 0805
1K 0603 10K 0603 BST2 BST1 +5.5V HDR2 1
LDR1 4 21
PDIM LDR1 VREF VREF
ENA C4
243K 0603
R16
3.3M 0603 1%
R11
LDR2 5 20 1uF/50V 0805 R39 C61
LDR2 VIN C11 10K 0603 470PF 0603
R15 6 19 ENA C2 0.1/16V 2.2u/16V
R5 R2 5.1K GND ENA R7
33K 0603 100K 0603 7 18 ADIM C3 2.2u/16V 30.1K 0603
RPT ADIM
8 17
CT UVLS
9 16 R36
SYNC OVPT 22R 0805
10 15 LDR2 1
LCT TIMER R10
PDIM 11 14 C16 R8 C17 100K 0603
PDIM SSTCMP 1nF 0603/NC 47K 0603/NC 0.1/16V R43 C62
C1 R6 C19 C14 12 13 10K 0603 470PF 0603
82pF NPO 0603 620K 0603 4.7nF 1nF/50V VSEN_POL ISEN
OZ9926A C18 C15

47nF 0603 2.2u/16V
D7
BAV70 R24
VREF 1 R20 100K 0603
VS1
v sen 3 100K 0603
2
VS2
D15
R42 D13 BAT54A
1K/NC R32 D8 BAT54A 1
IS7
5.1K 0603 C20 R12 BAV70 1 3
IS3
R40 1nF 0603 1M 0603 1 3 2
VS3 IS5
5.1K/NC 3 2
ADIM IS1
2 R25
VS4
R21 100K 0603
100K 0603
R41 D9 R14
C30 C31 5.1K BAV70 5.1K 0603
22u/10V/NC 0.1/16V/NC 1
VS5
3
2
VS6
Q5
3
D10 C21 R13 RK7002 R17
BAV70 1nF 0603/NC 39K 0603 10K 0603 R22 R26
1 1 100K 0603 100K 0603
VS7 VREF
3
2
VS8
C34
2
NC/1uF/50V Q6 D14 D16
3
D11 RK7002 D2 BAT54A BAT54A
Innolux BAV70 MM4148 1 1
IS4 IS8
1 1 3 3
VS9
Title 3 2 2
IS2 IS6
2.1 Dell 2209WA Inv erter 2
VS10
2
Size Document Number Rev R23 R27
A3 <Doc> R1 D12 R19 C22 100K 0603 100K 0603
BAV70
Date: Sheet 1 of 2 1 1nF 0603
VS11
3
2
VS12
1M 0603
76

Service Manual
P1 P5
1 1 4 T9 6
VA
4 T1 6 HV Leader 4 T5 6 HV Leader
VA VA
R76
R68 R72 30.1K 0603
VS9
30.1K 0603 30.1K 0603
VS1 VS5
2 1 C45 R52
VB
2 1 C37 R44 2 1 C41 R48 270PF/50V NPO 0603 4.7K 0603
VB VB
270PF/50V NPO 0603 3.3K 0603 270PF/50V NPO 0603 4.3K 0603 SPW-127
SPW-127 SPW-127
IS5
IS1
R64
R60 C53 1.4K 1% 0603
C64 1.4K 1% 0603 33nF/25V X7R 0603 D27
100pF/50V X7R 0603 R56 C49 D23 BAV99/SOT
D19 1.4K 1% 0603 33nF/25V X7R 0603 BAV99/SOT
BAV99/SOT
P2 P6
1 1 4 T10 6
4 T2 6 HV Leader 4 T6 6 HV Leader
R77
R69 R73 30.1K 0603
VS10
30.1K 0603 30.1K 0603
VS2 VS6
2 1 C46 R53
2 1 C38 R45 2 1 C42 R49 270PF/50V NPO 0603 4.3K 0603
270PF/50V NPO 0603 3.6K 0603 270PF/50V NPO 0603 3.9K 0603 SPW-127
SPW-127 SPW-127
IS6
IS2
C65 R65
100pF/50V X7R 0603 R61 C54 590R, 1% 0603
R57 C50 590R, 1% 0603 2.2nF/25V X7R 0603 D28
590R, 1% 0603 2.2nF/25V X7R 0603 D24 BAV99/SOT
D20 BAV99/SOT
BAV99/SOT
P7
P3
1 4 T11 6
1 VA
4 T7 6 HV Leader
VA
4 T3 6 HV Leader R78
VA
R74 30.1K 0603
VS11
R70 30.1K 0603
VS7
30.1K 0603
VS3
2 1 C47 R54
VB
2 1 C43 R50 270PF/50V NPO 0603 4.3K 0603
VB
2 1 C39 R46 270PF/50V NPO 0603 4.3K 0603 SPW-127
VB
270PF/50V NPO 0603 3.6K 0603 SPW-127
SPW-127
IS7
IS3
R66
C68 1.4K 1% 0603
C66 R62 C55 100pF/50V X7R 0603
R58 C51 100pF/50V X7R 0603 1.4K 1% 0603 33nF/25V X7R 0603 D29
1.4K 1% 0603 33nF/25V X7R 0603 D25 BAV99/SOT
D21 BAV99/SOT
BAV99/SOT
P8
P4
1 4 T12 6
1 4 T8 6 HV Leader
4 T4 6 HV Leader R79
R75 30.1K 0603
R71 30.1K 0603
VS8
30.1K 0603
VS4
2 1 C48 R55
2 1 C44 R51 270PF/50V NPO 0603 3.6K 0603
2 1 C40 R47 270PF/50V NPO 0603 4.3K 0603 SPW-127
270PF/50V NPO 0603 3.6K 0603 SPW-127
SPW-127
IS8
IS4
C67 R67
100pF/50V X7R 0603 C69 590R, 1% 0603
R63 C56 100pF/50V X7R 0603
R59 C52 590R, 1% 0603 2.2nF/25V X7R 0603 D30
590R, 1% 0603 2.2nF/25V X7R 0603 D26 BAV99/SOT
D22 BAV99/SOT
BAV99/SOT
Innolux
Title
2.2 Dell 2209WA Inv erter Transf ormer

A3 <Doc>
Date: Tuesday , September 16, 2008
C:\Documents and
Settings\F3110995\My Documents\invert.pdf
3. keypad schematic
77

Service Manual
CN101
8PIN 1.25
8
7
6
5
4
3
2
1
S05 S04 S03 S02 S01
1 1 1 1 Blue Amber 1
3
LED01
LED G/A
2 2 2 2 2
2
MENU PLUS MINUS SELECT POWER
4. USB convert board schematic

P001 P002
CN102 DOWN PORT1 DOWN PORT1
1 1
1 PWR4 GND GND
2 DD4M
3 DD4P DD4P 2 DD3P 2
4 D+ D+
DD3P DD4M 3 DD3M 3

5 DD3M D- D-
6 PWR3
7 PWR4 4 PWR3 4
8 VBUS VBUS
CON10
C101
+ C103 +
100uF/16V
100uF/16V
S S
S S S
78

Service Manual
79

Service Manual
Attachment 3- PCB Layout power/inverter bd:

inverter board:
Top Layer
Bottom Layer
80

Service Manual
Main board:
Top Layer
81

Service Manual
Bottom Layer
82

Service Manual
Keypad:
USB convert board
83

Service Manual
84

Service Manual LCD Monitor Dell 2209WA

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual LCD Monitor Dell 2209WA

Uploaded by

Copyright:

Available Formats

Service Manual

Service Manual Versions and Revision

1 2.0 2008/10/17 Initial Release

All Rights Reserved

Dell 2209WA Service Manual

Downloaded from www.Manualslib.com manuals search engine

CHAPTER 6- TROUBLE SHOOTING ................................................................................................................................

POWER 24V ON/OFF

+24V DC output 24V ON/OFF Control

+24V /+12V/+5V DC Jack AUDIO Detect

DCR PWM signal

PC Hub input 2port USB

Electronic Circuit Theory

2.2 Power PWM circuit

+24V DC output 24V ON/OFF Control

+24V /+12V/+5V DC Jack AUDIO Detect

2.2.2) AC Input and EMI Filter:(fig.5)

2.2.3)High Voltage to Low Voltage Control Circuit:(fig.6)

L853 L855 L856 D860 L857 L858 FR850

1M2 300K L859

R874 R834 R989

Signal GND Signal GND

GDZ20B 20V 47uF/50V 104p/50V

0402 R941 2SK3265

10K 470 R956

HIGH ON R898 C954 R959

D850 is a rectifier in which there are 4 build-in diodes, inverting AC to

PFC output voltage control. For an universal input (90VAC~264VAC)

Range=Open Voutput =〔(R981+R982+R983+R984+R822)/R821〕*3V

Range=Ground Voutput =〔(R981+R982+R983+R984)+(R822// R821)/

U850 provides an OTP pin for over-temperature protection. A constant

2.2.4)DC_24V ,DC 12V and DC 5V Output Circuit and Feedback circuit:(fig.7)

1000p/1KV 20 3W L854 F851

330 1% R971 R972 R973

R968 0.1/50V R976

2.2.5) Audio Power output:(fig.8)

2.3 I/F Board Circuit (see the Attachment 2- Schematic)

2.3.2 DVI CAPTURE

Please refer to TSUMU58EHJ-LF Pin Assignments table in page

3. FACTORY PRESET TIMING TABLE

4. Power On/Off Sequency

Software power On/Off

Power supply for panel+5V VDD

Signals Valid data

T1(ms) T2 (ms) T3 (ms) T4 (ms) T5 (ms) T6 (ms) T7(ms)

5. D-SUB Connector Pin Assignment

Pin Symbol Pin Symbol Pin Symbol

6. AC Outlet Pin Assignment

Pin Symbol Description

7. Inner Connector Pin Assignment

7.2 CN1, CN2 (Connect to Panel Backlight,)

7.3 CN104 (Connect to keypad, WAFER2*4P or compatible connector)

8.2 U108 (Serial Flash)

Downloaded from www.Manualslib.com manuals search engine

Mi d Fr ame, LP2236, Si l ver 501010221102R TAPE ACE W28mmXL15mm 506381001710R 3

LP2236 DISASSEMBLY BLOCK

shield EMI LP2207*4 CHASSIS-BTM ASSY l ogo- UX383* 1

power board* 1 (screw,f,cross,

kensington lock*1 usb board* 1

vesa release button*1

BACK COVER ASSY*1

Note: 1. The arrows point out the direction of disassembly.

LP2236 BOM STRUCTURE

CHASSIS-surport kensington lock*1

shield EMI LP22074 CHASSIS-BTM ASSY l ogo- UX383 1

kensington lock1 usb board 1

ASSY CHASSIS-BTM, 1 button power key1

(P,Cross,W/WAS,M36,Zn-Cc)5 STAND ASSY*1