ECM Calibration: Enhancement To Shifting Performance & Smoothness
ECM Calibration: Enhancement To Shifting Performance & Smoothness
Applicability
• Applicability has been updated to include 2007 – 2008 model year Solara and 2008 – 2009
model year Camry.
• Calibration IDs have been updated and added to the Calibration Identification Chart.
TSB No. EG036-07 is Obsolete and any printed versions should be discarded. Be sure to review
the entire content of this service bulletin before proceeding.
Introduction
To enhance shifting performance and smoothness during acceleration, the Engine Control
Module/ECM (SAE term: Powertrain Control Module/PCM) calibration has been revised. Use the
following repair procedure to address customer concerns.
Warranty Information
APPLICABLE WARRANTY
• This repair is covered under the Toyota Federal Emission Warranty. This warranty is in effect
for 96 months or 80,000 miles, whichever occurs first, from the vehicle’s in-service date.
Calibration Information
33366000
Federal 33366100 333A5100
333A5000
5AT
33368000
2007–2009 Camry BE46K
Calif. 33368100 333A7100
333A7000
33367000
MT 333A6100
2AZ-FE 333A6000
30658000
30658100
5AT 30660100
Federal 30658200
2007–2008 Solara 30660000 CE30P
30628000
5MT 30657000 30628100
30657100
Parts Information
89661-06F50
89661-06F51 89661-06F91 –
89661-06F90
Solara
89661-06F61
89661-06F62 89661-06G01 –
89661-06G00
89661-06C40
89661-06C41 89661-06G11 –
Federal
89661-06G10
89661-06C50
89661-06G21 –
89661-06G20
ECM (PCM)
89661-33B70
89661-33B71 89661-33E31 –
89661-33E30
Camry
89661-33B80
89661-33E41 –
89661-33E40
89661-06C70
89661-06C71 89661-06G41 –
89661-06G40
California
89661-33B90
89661-33B91 89661-33E51 –
89661-33E50
Authorized Modification
N/A 00451-00001-LBL Same 1
Labels
NOTE
• The ECM (PCM) should NOT be replaced as part of the repair procedure.
TIS techstream*
ADE TSUNT 1
NOTE: Software version 3.00.021 or later is required.
* Essential SST.
NOTE
* Essential SST.
NOTE
• Additional SSTs may be ordered by calling SPX/OTC at 1-800-933-8335.
• The GR8 Battery Diagnostic Station (P/N 00002-MCGR8) supersedes the Automatic Trickle
Charger (P/N 00002-YA122-01) and Fast Battery Chargers (Associated P/N ASE6003 and
Christie P/N CAPPDQ). P/N 00002-YA122-01, ASE6003, and CAPPDQ are now obsolete.
Repair Procedure
1. Check for the Authorized Modifications Label affixed to the vehicle in the location shown in
Figure 1. Confirm if the ECM (PCM) calibration has been updated. If the calibration ID listed is
NOT the latest ECM (PCM) calibration — go to step 2.
Figure 1. Location of Authorized Modifications Label on 2007 Camry
1
2
3 4
5
NOTE
• The GR8 Battery Diagnostic Station MUST be used in Power Supply Mode to maintain
battery voltage at 13.5 volts while flash reprogramming the vehicle.
• For details on how to use the GR8 Battery Diagnostic Station, refer to the GR8 Instruction
Manual located on the Technical Information System (TIS), Diagnostics – Battery.
Follow the procedures outlined in TSB No. SS002-07, “Techstream ECU Flash Reprogramming
Procedure”, and flash the ECM (PCM) with the NEW calibration file update.
3. Start the engine and warm it up to normal operating temperature before test driving.
4. Test drive the vehicle to confirm proper vehicle operation and ECM (PCM) initial learning.
Refer to TIS:
2007 / 2008 / 2009 model year Camry Repair Manual,Drivetrain – Automatic
Transmission/Transaxle – “U250E Automatic Transaxle: Automatic Transaxle System: Road Test”
2007 or 2008model year Solara Repair Manual,Drivetrain – Automatic Transmission/Transaxle –
“U250E Automatic Transaxle: Automatic Transaxle System: Road Test”
5. Install the Authorized Modifications Label.
A. Using a permanent marker, enter the following information on the label:
• ECM part number [Refer to the Parts Information section for theCURRENT PART
NUMBER]
• Calibration ID(s) [Refer to the Calibration Identification Chart for the NEW
CALIBRATION ID]
• Dealer Code
• Repair Date
• Change Authority [This TSB number]
B. Affix the Authorized Modifications Label to the vehicle at the location shown in
Figure 1. The Authorized Modifications Label is available through the MDC,
P/N 00451-00001-LBL.