STYPE
STYPE
Jaguar S-TYPE
Use the bookmarks at left to access the required DTC Summary.
• Powertrain DTC Summaries: 2000 Model Year applies to vehicles up to VIN L86901
• Powertrain DTC Summaries: 2001 – 2002 Model Year applies to 2001 and 2002 MY
vehicles from VIN L86902 ON
Other S-TYPE Summaries apply as indicated by the Model Years in the titles.
Powertrain DTC Summaries
– DTC P1584
CHECK ENGINE MIL 1 1 TRIP – indicates that the CHECK ENGINE MIL is activated by a fault occurring during ONE “TRIP”.
(CK ENG) 2 2 TRIPS – indicates that the CHECK ENGINE MIL is activated by a fault occurring during TWO CONSECUTIVE “TRIPS”.
N NO – indicates that the CHECK ENGINE MIL is not activated.
POSSIBLE CAUSES HIGH VOLTAGE – High voltage can be either sensor supply voltage (5 volts) or B+ voltage.
SELF TESTS
Two technician initiated component self tests are available using PDU:
KOEO Key (ignition) On Engine Off – The KOEO self test determines if system components are operating within tolerances with the ignition switched ON and
the engine stopped.
KOER Key (ignition) On Engine Running – The KOER self test determines if system components are operating within tolerances with the ignition switched on
and the engine running. KOER flags self-test DTC P1001 if a component fails to operate within the specified limits but does not activate the CHECK ENGINE MIL.
V8 V6
AM IMAF AM IMAF
Stage 1 15.9 – 19.7 grams per second 3.15 v – 3.40 v 15.9 – 19.7 grams per second 3.40 v – 3.70 v
Stage 2 21.2 – 24.2 grams per second 3.50 v – 3.80 v 21.9 – 25.7 grams per second 3.90 v – 4.25 v
1 Start engine.
2 Move transmission mode switch between Normal and Sport. Verify switch state illumination.
3 Move the gear selector to all positions in the J Gate for five (5) seconds each. Verify the state illumination in each position.
4 Drive vehicle to bring the transmission fluid temperature up to normal operating temperature.
5 Stop vehicle.
6 Switch off all heavy electrical consumers: air conditioning, heaters, etc.
7 Transmission mode switch – Normal.
8 Select 2nd Gear; accelerate slowly. After 5 seconds, select 3rd Gear; accelerate slowly. After 5 seconds, select 4th Gear; accelerate slowly. After 5 seconds,
select Drive; cruise at 72 km/h (45 mph) for 30 seconds.
9 Stop vehicle.
10 Use the J Gate to shift through all gears while accelerating briskly to 87 km/h (55 mph). Cruise at this speed to allow torque converter lockup to occur in fifth gear.
11 Stop vehicle and repeat steps 8 through 10.
AAI Valve Air Assist Injection Valve IAT Sensor Intake Air Temperature Sensor
A/C Air conditioning IMT Valve Intake Manifold Tuning Valve
APP Sensor Accelerator Pedal Position Sensor IP Sensor Injection Pressure Sensor
B+ Battery Voltage KS 1 Knock Sensor – RH Bank
CHT Sensor Cylinder Head Temperature Sensor KS 2 Knock Sensor – LH Bank
CKP Sensor Crankshaft Position Sensor MAF Sensor Mass Air Flow Sensor
CMP Sensor 1 Camshaft Position Sensor – RH Bank PCM Powertrain Control Module
CMP Sensor 2 Camshaft Position Sensor – LH Bank PSP Switch Power Steering Pressure Switch
DLC Data Link Connector PTEC Powertrain Electronic Control
DPFE Sensor Differential Pressure Feedback EGR Sensor SCP Standard Corporate Protocol Network
ECT Sensor Engine Coolant Temperature Sensor TACM Throttle Actuator Control Module
EFT Sensor Engine Fuel Temperature Sensor TCC Torque converter clutch
EGR Exhaust Gas Recirculation TFT Sensor Transmission Fluid Temperature Sensor
EOT Sensor Engine Oil Temperature Sensor TP Sensor Throttle Position Sensor
EVAP Canister Close Valve Evaporative Emission Canister Close Valve VVT Valve 1 Variable Valve Timing Valve – RH Bank
EVAP Canister Purge Valve Evaporative Emission Canister Purge Valve VVT Valve 2 Variable Valve Timing Valve – LH Bank
FTP Sensor Fuel Tank Pressure Sensor
HO2 Sensor 1 / 1 Heated Oxygen Sensor – RH Bank / Upstream
HO2 Sensor 1 / 2 Heated Oxygen Sensor – RH Bank / Downstream
HO2 Sensor 2 / 1 Heated Oxygen Sensor – LH Bank / Upstream
HO2 Sensor 2 / 2 Heated Oxygen Sensor – LH Bank / Downstream
ACCF Air conditioning clutch output – fault detected EFPT Fuel injection pressure sensor (raw input)
ACCON A/C clutch commanded on EFPT1 Fuel injection pressure sensor before PCM default action
ACP Air conditioning high side pressure EFT Engine fuel temperature sensor (raw input)
ADCF Adaptive damping control output – fault detected EFT1 Engine fuel temperature sensor before PCM default action
AFT1F Adaptive fueling table 1 – failure EGR1 EGR output – open circuit detected
AFT2F Adaptive fueling table 2 – failure EGR2 EGR output – short circuit to ground detected
ASLIP Actual torque converter slip value EGRDC EGR duty cycle
ATMR1 Time since engine start EGRF EGR system failure
CAM ANGLE1 Actual position of right camshaft EOTA Engine oil temperature -actual
CAMDC Variable valve timing right bank duty cycle EPCS1 Electronic pressure control solenoid 1
CAMERR Actual position of right camshaft EPCS2 Electronic pressure control solenoid 2
CANPF EVAP Canister purge output – fault detected EPCS3 Electronic pressure control solenoid 3
CANVF EVAP Canister close valve output – fault detected EPCSF Electronic pressure control solenoid fault detected
CCSF Coast clutch solenoid fault detected FP1 Fuel pump – output fault detected
CHTC Cylinder head temperature before PCM default action FPDC Modulated fuel pump control – duty cycle
CLOOP Closed loop fuel FTPT Fuel tank pressure sensor
CLOOP1 Closed loop fuel with H02S fault FUEL Fuel tank level
CLV Calculated load value GEAR In gear
CVSDC EVAP Canister close valve duty cycle GRCUR Current transmission gear ratio
DOLF Data link output – fault detected H02S11 H02S bank 1 upstream sensor voltage –
ECT Engine coolant temperature – degrees Celsius before correcting for %h(CSD) condition.
ECT2 Engine coolant temperature – degrees Fahrenheit H02S12 H02S bank 1 downstream sensor voltage –
before correcting for %h(CSD) condition.
ECTF Engine coolant temperature sensor failure
H02S1D H02S voltage – bank 1 downstream
EDF Low speed fan output – fault detected
H02S1F Heated oxygen sensor 1 – failure LSFP Low speed fuel pump output – fault detected
H02S1U H02S voltage – bank 1 upstream MAFF Mass air flow sensor – failure
H02S1UA H02S bank 1 upstream heater current monitor MILF CHECK ENGINE MIL output fault detected
H02S2D H02S voltage – bank 2 downstream O212F H02S bank 1 downstream – heater fault detected
H02S2F Heated oxygen sensor 2 – failure OLOOP3 Open loop fuel – conditions not met; go to closed loop
H02S2U H02S voltage – bank 2 upstream OTRIP OBDII trip completed
HTR11 H02S bank 1 upstream – heater On PNPS Park neutral position sensor
IAC1 Idle speed control- fault detected REVSW Reverse switch (not used – manual transmission)
IAC2 Idle speed control output – over current fault detected RPM2 Engine speed
IATF Intake air temperature sensor failure RPM2 Engine speed
IEGR Differential pressure feedback EGR sensor input (raw) RTT Transmission gear ratio
IMCDC Intake manifold communications control – duty cycle SAFTOT Spark advance
IMCF Inlet manifold communications output – fault indicated SCACL Cruise control set/ acceleration switch
IMRCF Inlet manifold runner control output fault indicated SCAN Cruise control cancel switch
INDSA Park neutral position sensor SCN Cruise control null state
INJ1 Air assist injection fault SCOF Cruise control Off switch
ISC1 Idle speed control – desired RPM SCON Cruise control On switch
KAMRF1 Adaptive fuel correction multiplier – bank 1 SCRES Cruise control resume switch
KAMRF2 Adaptive fuel correction multiplier – bank 2 SCTAP Cruise control coast tap down switch
LAMBSE1 Desired open loop equivalence ratio – bank 1 SLIPA Absolute torque converter slip value (not used)
LAMBSE2 Desired open loop equivalence ratio – bank 2 SLIPD Desired torque converter slip value (not used)
LOAD Air charge load normalized to sea level
SSCM Shift solenoids – commanded gear TOTFM Transmission fluid temperature before PCM default action
SSDCM Shift solenoids commanded gear TOTLK Transmission over temperature lockup mode
SSDF Shift solenoid output fault TPS Throttle position
SSD1 Shift solenoid 1 TPSF Throttle position sensor failure
SSD1F Shift solenoid 1 output fault TRS1 Transmission range sensor 1
SSD2 Shift solenoid 2 TRS2 Transmission range sensor 2
SSD2F Shift solenoid 2 output fault TRS3 Transmission range sensor 3
SSD3 Shift solenoid 3 TRS4 Transmission range sensor 4
SSD3F Shift solenoid 3 output fault TSS Turbine speed sensor
TCCDC Torque converter clutch solenoid duty cycle VCT1F Variable valve timing bank 1 output – fault detected
TCCF Torque converter clutch solenoid duty cycle fault detected VCT2F Variable valve timing bank 2 output – fault detected
TCS Transmission control switch (D – 4 switch) VMVDC EVAP Canister purge valve duty cycle
TCTF Secondary throttle output – fault detected VMVM EVAP Canister purge valve output state monitor
TIS Transmission input speed (Turbine speed) VPWR Battery voltage
TMILF Transmission fault lamp output fault detected VSF Variable speed fan level
TOS Transmission output speed (OSS) VSS Vehicle speed sensor
TOT2 Actual transmission fluid temperature (TFT)
P0065 V8 EMS Air assisted fuel injection (AAI) KOEO – page 3, or 2 N None AAI System piping: restricted, disconnected,
OBD II control range / performance Comprehensive component broken
monitor engine management AAI Valve failure
drive cycle – page 7
P0066 V8 EMS Air assisted fuel injection (AAI) KOEO – page 3, or 2 N None AAI Valve B+ power supply circuit fault
OBD II control circuit malfunction KOER – page 3, or AAI Valve to PCM PWM drive circuit: open circuit,
high resistance, short circuit
Comprehensive component
monitor engine management AAI Valve failure
drive cycle – page 7
P0102 EMS MAF Sensor sense circuit low KOER – page 3, or 2 N None Restricted air filter
OBD II voltage Comprehensive component MAF Sensor to PCM sensing circuit high resistance
monitor engine management or open circuit
drive cycle – page 7 MAF Sensor to PCM sensing circuit intermittent
short circuit to ground
MAF Sensor supply circuit open circuit or short
circuit to ground
MAF Sensor failure
P0103 EMS MAF Sensor sense circuit high KOEO – page 3, or 2 N None MAF Sensor to PCM reference ground circuit open
OBD II voltage KOER – page 3, or circuit
MAF Sensor to PCM sensing circuit short circuit to
Comprehensive component high voltage
monitor engine management
drive cycle – page 7 MAF Sensor failure
P0112 EMS IAT Sensor sense circuit high voltage KOEO – page 3, or 2 N PCM Default: IAT Sensor to PCM wiring open circuit or high
OBD II (low temperature) KOER – page 3, or – IAT default value 38 °C resistance
(100 °F) IAT Sensor to PCM sensing circuit short circuit to
Comprehensive component high voltage
monitor engine management
drive cycle – page 7 IAT Sensor failure
P0113 EMS IAT Sensor sense circuit low voltage KOEO – page 3, or 2 N PCM Default: IAT Sensor to PCM sensing circuit short circuit to
OBD II (high temperature) KOER – page 3, or – IAT default value 38 °C ground
(100 °F) IAT Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0117 EMS ECT Sensor sense circuit low voltage KOEO – page 3, or 2 N PCM Default: Engine overheat condition – refer to P1285
OBD II (high temperature) KOER – page 3, or – ECT default value 102 °C ECT Sensor to PCM sensing circuit short circuit to
(215 °F) ground
Comprehensive component
V6 – Refer to DTC P1290 monitor engine management ECT Sensor failure
drive cycle – page 7
P0118 EMS ECT Sensor sense circuit high voltage KOEO – page 3, or 2 N PCM Default: ECT Sensor to PCM wiring open circuit or high
OBD II (low temperature) KOER – page 3, or – ECT default value 102 °C resistance
(215 °F) ECT Sensor to PCM sensing circuit short circuit to
Comprehensive component high voltage
V6 – Refer to DTC P1289 monitor engine management
drive cycle – page 7 ECT Sensor failure
P0122 EMS TP Sensor sense circuit low voltage – KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “1” (TP Sensor
JAG TP1 KOER – page 3, or signals are received from pin 10) open circuit or high resistance
remaining sensors) TP Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0123 EMS TP Sensor sense circuit high voltage KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “1” (TP Sensor
JAG – TP1 KOER – page 3, or signals are received from pin 10) short circuit to high voltage
remaining sensors) TP Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0124 EMS TP Sensor signal intermittent – TP1 Comprehensive component N N None (as long as normal TP TP Sensor to PCM sensing circuit “1” (TP Sensor
JAG monitor engine management signals are received from pin 10) intermittent: open circuit, high resistance,
drive cycle – page 7 remaining sensors) short circuit to ground or high voltage
TP Sensor failure
P0125 EMS ECT / CHT Sensor response Comprehensive component 2 N None Low coolant level
OBD II insufficient for closed loop fuel monitor engine management Contaminated coolant
metering control drive cycle – page 7
Engine coolant thermostat failure
CHT Sensor to cylinder head poor contact – V6
ECT / CHT Sensor to PCM sensing circuit: high
resistance, open circuit or short circuit to high
voltage
P0130 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None HO2 Sensor 1/1 to PCM sensing circuit: open
OBD II malfunction – bank 1, upstream (1/1) monitor drive cycle – page 4 circuit, high resistance, short circuit to ground or
high voltage
HO2 Sensor 1/1 failure
P0131 EMS HO2 Sensor sense circuit low voltage Heated oxygen sensors 2 N None HO2 Sensor 1/1 disconnected
OBD II – bank 1, upstream (1/1) monitor drive cycle – page 4 HO2 Sensor 1/1 to PCM sensing circuit open circuit
HO2 Sensor 1/1 short circuit to ground
HO2 Sensor 1/1 failure
P0132 EMS HO2 Sensor sense circuit high KOER – page 3, or 2 N None HO2 Sensor 1/1 to PCM sensing circuit short circuit
OBD II voltage – bank 1, upstream (1/1) Heated oxygen sensors to high voltage
monitor drive cycle – page 4 HO2 Sensor 1/1 reference ground circuit (HO2
sensor to splice) open circuit
HO2 Sensor 1/1 failure
P0133 EMS HO2 Sensor sense circuit slow Heated oxygen sensors 2 N None Engine misfire
OBD II response – bank 1, upstream (1/1) monitor drive cycle – page 4 HO2 Sensor 1/1 disconnected
HO2 Sensor 1/1 mechanical damage
HO2 Sensor 1/1 to PCM wiring intermittent open
circuit
HO2 Sensor 1/1 to PCM sensing circuit short circuit
to high voltage
HO2 Sensor 1/1 short circuit to ground
HO2 Sensor 1/1 reference ground circuit (HO2
sensor to splice) open circuit
HO2 Sensor 1/1 heater circuit fault
Exhaust leak
Low exhaust temperature
Injector flow partially restricted
Catalyst efficiency decrease
HO2 Sensor 1/1 failure
P0135 EMS HO2 Sensor heater circuit KOEO – page 3, or 2 N None HO2 Sensor 1/1 disconnected
OBD II malfunction – bank 1, upstream (1/1) KOER – page 3, or HO2 Sensor 1/1 heater power supply open circuit
Heated oxygen sensors HO2 Sensor 1/1 heater to ECM wiring short circuit
monitor drive cycle – page 4 or open circuit
HO2 Sensor 1/1 heater failure
P0136 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None HO2 Sensor 1/2 to PCM sensing circuit: open
OBD II malfunction – bank 1, downstream (1/ monitor drive cycle – page 4 circuit, high resistance, short circuit to ground or
2) high voltage
HO2 Sensor 1/2 failure
P0138 EMS HO2 Sensor sense circuit high KOER – page 3, or 2 N None HO2 Sensor 1/2 to PCM sensing circuit short circuit
OBD II voltage – bank 1, downstream (1/2) Heated oxygen sensors to high voltage
monitor drive cycle – page 4 HO2 Sensor 1/2 reference ground circuit (HO2
sensor to splice) open circuit
HO2 Sensor 1/2 failure
P0141 EMS HO2 Sensor heater circuit KOEO – page 3, or 2 N None HO2 Sensor 1/2 disconnected
OBD II malfunction – bank 1, downstream KOER – page 3, or HO2 Sensor 1/2 heater power supply open circuit
(1/2)
Heated oxygen sensors HO2 Sensor 1/2 heater to ECM wiring short circuit
monitor drive cycle – page 4 or open circuit
HO2 Sensor 1/2 heater failure
P0150 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None HO2 Sensor 2/1 to PCM sensing circuit: open
OBD II malfunction – bank 2, upstream (2/1) monitor drive cycle – page 4 circuit, high resistance, short circuit to ground or
high voltage
HO2 Sensor 2/1 failure
P0151 EMS HO2 Sensor sense circuit low voltage Heated oxygen sensors 2 N None HO2 Sensor 2/1 disconnected
OBD II – bank 2, upstream (2/1) monitor drive cycle – page 4 HO2 Sensor 2/1 to PCM sensing circuit open circuit
HO2 Sensor 2/1 short circuit to ground
HO2 Sensor 2/1 failure
P0152 EMS HO2 Sensor sense circuit high KOER – page 3, or 2 N None HO2 Sensor 2/1 to PCM sensing circuit short circuit
OBD II voltage – bank 2, upstream (2/1) Heated oxygen sensors to high voltage
monitor drive cycle – page 4 HO2 Sensor 2/1 reference ground circuit (HO2
sensor to splice) open circuit
HO2 Sensor 2/1 failure
P0153 EMS HO2 Sensor sense circuit slow Heated oxygen sensors 2 N None Engine misfire
OBD II response – bank 2, upstream (2/1) monitor drive cycle – page 4 HO2 Sensor 2/1 disconnected
HO2 Sensor 2/1 mechanical damage
HO2 Sensor 2/1 to PCM wiring intermittent open
circuit
HO2 Sensor 2/1 to PCM sensing circuit short circuit
to high voltage
HO2 Sensor 2/1 short circuit to ground
HO2 Sensor 2/1 reference ground circuit (HO2
sensor to splice) open circuit
HO2 Sensor 2/1 heater circuit fault
Exhaust leak
Low exhaust temperature
Injector flow partially restricted
Catalyst efficiency decrease
HO2 Sensor 2/1 failure
P0155 EMS HO2 Sensor heater circuit KOEO – page 3, or 2 N None HO2 Sensor 2/1 disconnected
OBD II malfunction – bank 2, upstream (2/1) KOER – page 3, or HO2 Sensor 2/1 heater power supply open circuit
Heated oxygen sensors HO2 Sensor 2/1 heater to ECM wiring short circuit
monitor drive cycle – page 4 or open circuit
HO2 Sensor 2/1 heater failure
P0156 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None HO2 Sensor 2/2 to PCM sensing circuit: open
OBD II malfunction – bank 2, downstream (2/ monitor drive cycle – page 4 circuit, high resistance, short circuit to ground or
2) high voltage
HO2 Sensor 2/2 failure
P0158 EMS HO2 Sensor sense circuit high KOER – page 3, or 2 N None HO2 Sensor 2/2 to PCM sensing circuit short circuit
OBD II voltage – bank 2, downstream (2/2) Heated oxygen sensors to high voltage
monitor drive cycle – page 4 HO2 Sensor 2/2 reference ground circuit (HO2
sensor to splice) open circuit
HO2 Sensor 2/2 failure
P0161 EMS HO2 Sensor heater circuit KOEO – page 3, or 2 N None HO2 Sensor 2/2 disconnected
OBD II malfunction – bank 2, downstream KOER – page 3, or HO2 Sensor 2/2 heater power supply open circuit
(2/2)
Heated oxygen sensors HO2 Sensor 2/2 heater to ECM wiring short circuit
monitor drive cycle – page 4 or open circuit
HO2 Sensor 2/2 heater failure
P0171 EMS System too lean – bank 1 Adaptive fuel monitor drive 2 N None Engine misfire
OBD II cycle – page 4 Air intake leak between MAF Sensor and throttle
Fuel filter, system restriction
Fuel injector restriction
Fuel pressure sensor failure (low fuel pressure)
Low fuel pump output
HO2 Sensor(s) (1/1, 1/2) harness wiring condition
fault
Exhaust leak (before catalyst)
PCM receiving incorrect signal from one or more of
the following components: ECT or CHT Sensor,
MAF Sensor, IAT Sensor, IP Sensor, EFT Sensor,
TP Sensor(s), TACM
P0172 EMS System too rich – bank 1 Adaptive fuel monitor drive 2 N None Restricted air filter
OBD II cycle – page 4 Leaking fuel injector(s)
Fuel pressure sensor failure (high fuel pressure)
PCM receiving incorrect signal from one or more of
the following components: ECT or CHT Sensor,
MAF Sensor, IAT Sensor, IP Sensor, EFT Sensor,
TP Sensor(s), TACM
P0174 EMS System too lean – bank 2 Adaptive fuel monitor drive 2 N None Engine misfire
OBD II cycle – page 4 Air intake leak between MAF Sensor and throttle
Fuel filter, system restriction
Fuel injector restriction
Fuel pressure sensor failure (low fuel pressure)
Low fuel pump output
HO2 Sensor(s) (2/1, 2/2) harness wiring condition
fault
Exhaust leak (before catalyst)
PCM receiving incorrect signal from one or more of
the following components: ECT or CHT Sensor,
MAF Sensor, IAT Sensor, IP Sensor, EFT Sensor,
TP Sensor(s), TACM
P0175 EMS System too rich – bank 2 Adaptive fuel monitor drive 2 N None Restricted air filter
OBD II cycle – page 4 Leaking fuel injector(s)
Fuel pressure sensor failure (high fuel pressure)
PCM receiving incorrect signal from one or more of
the following components: ECT or CHT Sensor,
MAF Sensor, IAT Sensor, IP Sensor, EFT Sensor,
TP Sensor(s), TACM
P0180 EMS EFT Sensor circuit malfunction KOEO – page 3, or 2 N None EFT Sensor disconnected
OBD II KOER – page 3, or EFT Sensor to PCM sensing circuit: high
resistance, open circuit, short circuit to ground or
Comprehensive component high voltage
monitor engine management
drive cycle – page 7 EFT Sensor failure
P0190 EMS IP Sensor circuit malfunction Comprehensive component 2 N None IP Sensor reference ground circuit (to splice) open
OBD II monitor engine management circuit
drive cycle – page 7 IP Sensor reference voltage circuit (to splice) open
circuit
IP Sensor to PCM sensing circuit; open circuit, high
resistance, short circuit to ground or high voltage
IP Sensor failure
P0192 EMS IP Sensor sense circuit low voltage KOEO – page 3, or 2 N None IP Sensor reference voltage circuit (to splice) open
OBD II (low pressure) KOER – page 3, or circuit
IP Sensor to PCM sensing circuit; open circuit, high
Comprehensive component resistance, short circuit to ground
monitor engine management
drive cycle – page 7 IP Sensor failure
P0193 EMS IP Sensor sense circuit high voltage KOEO – page 3, or 2 N None IP Sensor reference ground circuit (to splice) open
OBD II (high pressure) KOER – page 3, or circuit
IP Sensor to PCM sensing circuit short circuit to
Comprehensive component high voltage
monitor engine management
drive cycle – page 7 IP Sensor failure
P0196 EMS EOT Signal does not follow CHT / Comprehensive component 2 N PCM Default: EOT Sensor to PCM sensing circuit high resistance
OBD II ECT signal monitor engine management – V6 CHT substituted when hot
drive cycle – page 7 EOT Sensor to PCM sensing circuit intermittent
– V8 ECT substituted high resistance
EOT Sensor failure
P0222 EMS TP Sensor sense circuit low voltage – KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “2” (TP Sensor
JAG TP2 KOER – page 3, or signals are received from pin 1) open circuit or high resistance
remaining sensors) TP Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0223 EMS TP Sensor sense circuit high voltage KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “2” (TP Sensor
JAG – TP2 KOER – page 3, or signals are received from pin 1) short circuit to high voltage
remaining sensors) TP Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0224 EMS TP Sensor signal intermittent – TP2 KOEO – page 3, or N N None (as long as normal TP TP Sensor to PCM sensing circuit “2” (TP Sensor
JAG KOER – page 3, or signals are received from pin 1) intermittent: open circuit, high resistance,
remaining sensors) short circuit to ground or high voltage
Comprehensive component TP Sensor failure
monitor engine management
drive cycle – page 7
P0227 EMS TP Sensor sense circuit low voltage – KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “3” (TP Sensor
JAG TP3 KOER – page 3, or signals are received from pin 2) open circuit or high resistance
remaining sensors) TP Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0228 EMS TP Sensor sense circuit high voltage KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “3” (TP Sensor
JAG – TP3 KOER – page 3, or signals are received from pin 2) short circuit to high voltage
remaining sensors) TP Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0229 EMS TP Sensor signal intermittent – TP3 KOEO – page 3, or N N None (as long as normal TP TP Sensor to PCM sensing circuit “3” (TP Sensor
JAG KOER – page 3, or signals are received from pin 2) intermittent: open circuit, high resistance,
remaining sensors) short circuit to ground or high voltage
Comprehensive component TP Sensor failure
monitor engine management
drive cycle – page 7
P0300 EMS Random misfire detected Misfire monitor drive cycle – 1 or 2 N None Cylinder compression low
OBD II page 4 ** Worn camshaft / broken valve spring(s)
Fuel delivery pressure (low / high)
Fuel injector(s) restricted / leaking
Fuel injector(s) continuously open
Fuel contamination
Fuel injector circuit fault(s) (Injector DTCs also
flagged)
Spark plug failure / fouled / incorrect gap
PCM to ignition coil primary circuit fault (Cylinder
misfire detected DTC also flagged)
Ignition coil failure
P0301 EMS Misfire detected – cylinder 1 (1/1) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0302 EMS Misfire detected – cylinder 2 (1/2) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0303 EMS Misfire detected – cylinder 3 (1/3) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0304 EMS Misfire detected – cylinder 4 (1/4 V8, Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II 2/1 V6) page 4 **
P0305 EMS Misfire detected – cylinder 5 (2/1 V8, Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II 2/2 V6) page 4 **
P0306 EMS Misfire detected – cylinder 6 (2/2 V8, Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II 2/3 V6) page 4 **
**If the misfire is severe enough to cause catalyst damage, the individual cylinder DTC will be flagged immediately and the CHECK ENGINE MIL will flash.
P0307 V8 EMS Misfire detected – cylinder 7 (2/3 V8) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0308 V8 EMS Misfire detected – cylinder 8 (2/4 V8) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0320 EMS CKP Sensor circuit malfunction Comprehensive component 2 N None CKP Sensor disconnected
OBD II monitor engine management (The engine will shut off) CKP Sensor gap incorrect
drive cycle – page 7
CKP Sensor reluctor damaged teeth
Foreign matter on CKP Sensor face – V8
Foreign matter on CKP Sensor (on drive plate) – V8
CKP Sensor sensing circuit open circuit, high
resistance, short circuit to ground or high voltage
CKP Sensor failure
P0325 EMS KS (knock sensor) circuit malfunction KOER – page 3, or 2 N None Poor sensor contact with the cylinder block
OBD II – bank 1 V8 Comprehensive component KS to PCM sensing circuit (KS pin 2): open circuit,
– front (bank 2) V6 monitor engine management high resistance, short circuit to ground or high
drive cycle – page 7 voltage
KS to PCM reference ground circuit (KS pin 1): open
circuit, high resistance, short circuit to high
voltage
KS failure
P0330 EMS KS (knock sensor) circuit malfunction KOER – page 3, or 2 N None Poor sensor contact with the cylinder block
OBD II – bank 2 V8 Comprehensive component KS to PCM sensing circuit (KS pin 2): open circuit,
– rear (bank 1) V6 monitor engine management high resistance, short circuit to ground or high
drive cycle – page 7 voltage
KS to PCM reference ground circuit (KS pin 1): open
circuit, high resistance, short circuit to high
voltage
KS failure
**If the misfire is severe enough to cause catalyst damage, the individual cylinder DTC will be flagged immediately and the CHECK ENGINE MIL will flash.
P0340 EMS CMP Sensor circuit malfunction – Comprehensive component 2 N PCM Default: Bank 1 CMP Sensor disconnected
OBD II bank 1 monitor engine management – VVT inhibited Bank 1 CMP Sensor gap incorrect / foreign matter
drive cycle – page 7 on sensor face
(Decreased engine
performance) Bank 1 CMP Sensor sensing circuit: open circuit,
short circuit to ground, short circuit to high
voltage
Bank 1 CMP Sensor reference ground circuit (to
splice) open circuit
Bank 1 CMP Sensor failure
P0341 EMS CMP Sensor circuit malfunction – Comprehensive component 2 N PCM Default: Bank 2 CMP Sensor disconnected
OBD II bank 2 monitor engine management – VVT inhibited Bank 2 CMP Sensor gap incorrect / foreign matter
drive cycle – page 7 on sensor face
(Decreased engine
performance) Bank 2 CMP Sensor sensing circuit: open circuit,
short circuit to ground, short circuit to high
voltage
Bank 2 CMP Sensor reference ground circuit (to
splice) open circuit
Bank 2 CMP Sensor failure
P0350 EMS Ignition coil primary circuit Comprehensive component 2 N None Ignition coils power supply; open circuit, short
OBD II malfunction – undetermined cylinder monitor engine management circuit
identification drive cycle – page 7 Ignition suppression capacitor(s) failure
Incorrect CKP Sensor air gap
P0351 EMS Ignition coil primary circuit Comprehensive component 2 N None Ignition coil disconnected
OBD II malfunction – cylinder 1/1 monitor engine management PCM to ignition coil primary circuit: open circuit,
drive cycle – page 7 high resistance, short circuit to ground
Ignition coil failure
(If other individual ignition coil primary circuit DTCs
are flagged, refer to P0350 Possible Causes)
P0352 EMS Ignition coil primary circuit Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II malfunction – cylinder 1/2 monitor engine management
drive cycle – page 7
P0353 EMS Ignition coil primary circuit Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II malfunction – cylinder 1/3 monitor engine management
drive cycle – page 7
P0354 EMS Ignition coil primary circuit Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II malfunction – V6 cylinder 2/1; monitor engine management
V8 cylinder 1/4 drive cycle – page 7
P0355 EMS Ignition coil primary circuit Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II malfunction – V6 cylinder 2/2; monitor engine management
V8 cylinder 2/1 drive cycle – page 7
P0356 EMS Ignition coil primary circuit Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II malfunction – V6 cylinder 2/3; monitor engine management
V8 cylinder 2/2 drive cycle – page 7
P0357 V8 EMS Ignition coil primary circuit Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II malfunction – V8 cylinder 2/3 monitor engine management
drive cycle – page 7
P0358 V8 EMS Ignition coil primary circuit Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II malfunction – V8 cylinder 2/4 monitor engine management
drive cycle – page 7
P0401 V6 EMS EGR flow insufficient detected EGR monitor drive cycle – 2 N None DPFE Sensor to PCM sensing circuit (sensor pin 1)
OBD II page 6 open circuit, high resistance
EGR Valve stuck closed or restricted
EGR Valve vacuum hose, restricted, disconnected
or broken
P0402 V6 EMS EGR flow excessive detected KOER – page 3, or 2 N None EGR Valve stuck open
OBD II EGR monitor drive cycle – EGR Valve seat held open by debris
page 6
P0420 EMS Catalytic converter system efficiency Catalyst efficiency monitor 2 N None Bank 1 HO2 sensor(s) disconnected
OBD II below threshold – bank 1 drive cycle – page 5 Bank 1 HO2 sensor(s) to PCM wiring fault
Bank 1 HO2 sensor(s) heater to PCM wiring fault
Bank 1 HO2 sensor(s) heater failure
Bank 1 upstream HO2 sensor failure
Bank 1 downstream HO2 sensor failure
Bank 1 catalyst failure
P0430 EMS Catalytic converter system efficiency Catalyst efficiency monitor 2 N None Bank 2 HO2 sensor(s) disconnected
OBD II below threshold – bank 2 drive cycle – page 5 Bank 2 HO2 sensor(s) to PCM wiring fault
Bank 2 HO2 sensor(s) heater to PCM wiring fault
Bank 2 HO2 sensor(s) heater failure
Bank 2 upstream HO2 sensor failure
Bank 2 downstream HO2 sensor failure
Bank 2 catalyst failure
P0442 EMS EVAP Control system leak detected – Evaporative system monitor 2 N None Fuel cap seal defective
OBD II small leak drive cycle – page 6 EVAP system leak (canister damage, pipework
damage)
EVAP Canister purge valve to PCM drive circuit
open circuit, short circuit, high resistance
EVAP Canister purge valve power supply circuit
open circuit
EVAP Canister purge valve to engine purge pipe
damaged / restricted / leaking
EVAP Canister purge valve operating vacuum hose
leak / restriction
EVAP Canister purge failure
Fuel tank leak
P0443 EMS EVAP Canister purge valve circuit KOEO – page 3, or 2 N None EVAP Canister purge valve to PCM drive circuit
OBD II malfunction KOER – page 3, or open circuit, short circuit, high resistance
EVAP Canister purge valve power supply circuit
Evaporative system monitor open circuit
drive cycle – page 6
EVAP Canister purge valve failure
P0451 EMS FTP Sensor range / performance Evaporative system monitor 2 N None FTP Sensor disconnected
OBD II drive cycle – page 6 FTP Sensor to PCM sensing circuit open circuit,
short circuit to ground, short circuit to B+ voltage
FTP Sensor to PCM reference voltage circuit open
circuit or short circuit to ground
FTP Sensor to PCM wiring (supply, sense,
reference ground) short circuit to each other
FTP Sensor failure
P0452 EMS FTP Sensor circuit low voltage (low KOEO – page 3, or 2 N None FTP Sensor disconnected
OBD II pressure) KOER – page 3, or FTP Sensor to PCM sensing circuit open circuit or
short circuit to ground
Evaporative system monitor
drive cycle – page 6 FTP Sensor to PCM reference voltage circuit open
circuit or short circuit to ground
FTP Sensor failure
P0453 EMS FTP Sensor circuit high voltage (high KOEO – page 3, or 2 N None FTP Sensor to PCM wiring (supply, sense,
OBD II pressure) KOER – page 3, or reference ground) short circuit to each other
FTP Sensor to PCM sense circuit short circuit to
Evaporative system monitor
drive cycle – page 6 high voltage
FTP Sensor to PCM reference ground circuit open
circuit
P0455 EMS EVAP Control system control-leak Evaporative system monitor 2 N None Fuel cap off
OBD II detected – major leak drive cycle – page 6 Fuel cap seal defective
Fuel tank over filled
EVAP system leak (canister damage, pipework
damage)
EVAP Canister purge valve to PCM drive circuit
open circuit, short circuit, high resistance
EVAP Canister purge valve power supply circuit
open circuit
EVAP Canister purge valve to engine purge pipe
damaged / restricted / leaking
EVAP Canister purge valve operating vacuum hose
leak / restriction
EVAP Canister purge failure
FTP Sensor not responding to pressure changes
(restricted / failure)
Fuel tank leak
P0456 EMS EVAP Control system control-leak Evaporative system monitor 2 N None Refer to P0456 Possible Causes (except fuel cap
OBD II detected – small leak (0.5 mm; 0.020 drive cycle – page 6 off)
in.)
P0460 EMS Fuel level sensor(s) circuit KOEO – page 3, or N N None Fuel level sensor(s) to RECM sense circuits: open
JAG malfunction KOER – page 3, or circuit, high resistance, short circuit
RECM / PCM SCP communication fault (U Code
Evaporative system monitor flagged)
drive cycle – page 6
Fuel level sensor(s) failure
P0500 ABS/TC Vehicle speed circuit malfunction Engine running; vehicle in N N None Rear wheel speed sensor(s) circuit(s): open circuit,
JAG motion high resistance, short circuit
Rear wheel speed sensor(s) failure
Front wheel speed sensor(s) circuit(s): open circuit,
high resistance, short circuit
Front wheel speed sensor(s) failure
Instrument pack malfunction
SCP Failure (code U1039 flagged)
P0503 TRANS Vehicle speed circuit – electrical Engine running; vehicle in N N None Wheel speed sensor(s) circuit(s) electrical noise
JAG noise motion Instrument pack malfunction
SCP Failure (code U1039 flagged)
P0505 EMS Idle air control malfunction KOER – page 3 N N None Engine air filter restricted / defective
JAG Engine air intake restricted / damaged
PCM / TACM circuit fault
TACM failure
Throttle failure
P0602 PCM PCM Programming error KOEO – page 3, or N N None PCM failure
JAG KOER – page 3, or
Comprehensive component
monitor engine management
drive cycle – page 7
P0603 PCM PCM Keep alive memory (KAM) test KOEO – page 3 N N None PCM failure
JAG error
P0605 PCM PCM Read only memory (ROM) test KOEO – page 3 N N None PCM failure
JAG error
P0703 EMS Brake ON / OFF switch circuit Engine running; operate brake N M, S PCM Default: Brake switch to PCM signal circuit: open circuit,
JAG malfunction pedal – Speed control inhibited high resistance, short circuit
Brake switch power supply circuit: open circuit,
short circuit
Brake switch signal circuit (gearshift interlock, ABS/
TC, stop lamps): open circuit, short circuit
Brake switch failure
P0704 V6 EMS Clutch pedal switch circuit KOEO – page 3, or N M, S PCM Default: Clutch pedal switch to PCM signal circuit: open
JAG malfunction KOER – page 3 – Speed control inhibited circuit, high resistance, short circuit
(Manual transmission) PCM to clutch pedal switch reference ground
circuit: open circuit, high resistance, short circuit
Clutch pedal switch failure
P0705 TRANS Range sensor circuit malfunction KOEO – page 3, or 2 A, M PCM Defaults to DRIVE (to Range sensor incorrect alignment
OBD II (sensor transmitting an invalid code) KOER – page 3, or maintain all five gears) Gear selector cable incorrectly adjusted
Comprehensive component J Gate gear selected Range sensor circuit: intermittent open circuit;
monitor transmission drive illumination extinguished open circuit
cycle – page 8 (Harsh shifts) Range sensor failure
P0708 TRANS Range sensor circuit open circuit KOEO – page 3, or 2 A, M PCM Defaults to DRIVE (to Range sensor circuit open circuit
OBD II KOER – page 3, or maintain all five gears) Range sensor disconnected
Comprehensive component J Gate gear selected Range sensor failure
monitor transmission drive illumination extinguished
cycle – page 8 (Harsh shifts)
P0712 TRANS TFT Sensor sense circuit low voltage KOEO – page 3, or N A, M, T PCM Default: TFT Sensor sense circuit short circuit to ground
JAG (high fluid temperature) KOER – page 3, or – TFT calculated from TFT Sensor failure
Comprehensive component ECT (V8) / CHT (V6)
monitor transmission drive ABS/TCCM, DSCCM Default:
cycle – page 8 – traction control inhibited
(Firm shifts)
P0713 TRANS TFT Sensor sense circuit high voltage KOEO – page 3, or N A, M, T PCM Default: TFT Sensor sense circuit: open circuit; high
JAG (low fluid temperature) KOER – page 3, or – TFT calculated from resistance; short circuit to high voltage
ECT (V8) / CHT (V6) TFT Sensor failure
Comprehensive component
monitor transmission drive ABS/TCCM, DSCCM Default:
cycle – page 8 – traction control inhibited
(Firm shifts)
P0715 TRANS Turbine speed sensor circuit KOER – page 3, or 2 A, M PCM Default: Turbine speed sensor circuit: short circuit; high
OBD II malfunction Comprehensive component – Speed calculated from resistance; open circuit
monitor transmission drive output speed sensor Turbine speed sensor failure
cycle – page 8
(Harsh TCC shifts)
P0717 TRANS Turbine speed sensor sense circuit – KOER – page 3, or N A, M PCM Default: Turbine speed sensor sense circuit open circuit
JAG no signal Comprehensive component – Speed calculated from Turbine speed sensor failure
monitor transmission drive output speed sensor
cycle – page 8
(Harsh TCC shifts)
P0718 TRANS Turbine speed sensor sense circuit – Comprehensive component N A, M PCM Default: Turbine speed sensor sense circuit: short circuit;
JAG electrical noise monitor transmission drive – Speed calculated from open circuit
cycle – page 8 output speed sensor
P0720 TRANS Output speed sensor circuit Comprehensive component 2 A, M PCM Default: Output speed sensor circuit: short circuit; high
OBD II malfunction monitor transmission drive – Speed calculated from SCP resistance; open circuit
cycle – page 8 vehicle speed message Output speed sensor failure
P0721 TRANS Output speed sensor sense circuit – Comprehensive component N A, M, T PCM Default: Output speed sensor sense circuit: short circuit;
JAG electrical noise monitor transmission drive – Speed calculated from SCP open circuit
cycle – page 8 vehicle speed message
ABS/TCCM, DSCCM Default:
– traction control inhibited
(Abnormal shift schedule)
P0722 TRANS Output speed sensor sense circuit – Comprehensive component N A, M, T PCM Default: Output speed sensor sense circuit intermittent:
JAG intermittent signal monitor transmission drive – Speed calculated from SCP short circuit; high resistance; open circuit
cycle – page 8 vehicle speed message Output speed sensor failure
ABS/TCCM, DSCCM Default:
– traction control inhibited
(Abnormal shift schedule)
P0731 TRANS 1st Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault (shift solenoid DTC(s)
JAG monitor transmission drive – 1st Gear inhibited also flagged)
cycle – page 8 Pressure control solenoid circuit fault (pressure
ABS/TCCM, DSCCM Default: solenoid DTC(s) also flagged)
– traction control inhibited Engine speed signal malfunction (CKP Sensor
DTC(s) also flagged)
Transmission mechanical failure
P0732 TRANS 2nd Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault (shift solenoid DTC(s)
JAG monitor transmission drive – 2nd Gear inhibited also flagged)
cycle – page 8 Pressure control solenoid circuit fault (pressure
ABS/TCCM, DSCCM Default: solenoid DTC(s) also flagged)
– traction control inhibited Engine speed signal malfunction (CKP Sensor
DTC(s) also flagged)
Transmission mechanical failure
P0733 TRANS 3rd Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault (shift solenoid DTC(s)
JAG monitor transmission drive – 3rd Gear inhibited also flagged)
cycle – page 8 Pressure control solenoid circuit fault (pressure
ABS/TCCM, DSCCM Default: solenoid DTC(s) also flagged)
– traction control inhibited Engine speed signal malfunction (CKP Sensor
DTC(s) also flagged)
Transmission mechanical failure
P0734 TRANS 4th Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault (shift solenoid DTC(s)
JAG monitor transmission drive – 4th Gear inhibited also flagged)
cycle – page 8 Pressure control solenoid circuit fault (pressure
ABS/TCCM, DSCCM Default: solenoid DTC(s) also flagged)
– traction control inhibited Engine speed signal malfunction (CKP Sensor
DTC(s) also flagged)
Transmission mechanical failure
P0735 TRANS 5th Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault (shift solenoid DTC(s)
JAG monitor transmission drive – 5th Gear inhibited also flagged)
cycle – page 8 Pressure control solenoid circuit fault (pressure
ABS/TCCM, DSCCM Default: solenoid DTC(s) also flagged)
– traction control inhibited Engine speed signal malfunction (CKP Sensor
DTC(s) also flagged)
Transmission mechanical failure
P0741 TRANS TCC Slip detected Comprehensive component N A, M, T Transmission will continue to TCC solenoid circuit fault (TCC solenoid DTC(s) also
JAG monitor transmission drive attempt lock-up flagged)
cycle – page 8 ABS/TCCM, DSCCM Default: Pressure control solenoid circuit fault (pressure
solenoid DTC(s) also flagged)
– traction control inhibited
Transmission mechanical failure
P0743 TRANS TCC Solenoid circuit malfunction KOEO – page 3, or 2 A, M PCM Default: TCC Drive circuit: open circuit; high resistance;
OBD II KOER – page 3, or – TCC Lock-up inhibited short circuit to ground
TCC solenoid failure
Comprehensive component
monitor transmission drive
cycle – page 8
P0745 TRANS Pressure control solenoid 1 stuck Comprehensive component 2 A, M PCM Default: Pressure control solenoid 1drive circuit: short
OBD II monitor transmission drive – 1st, 2nd, 4th, 5th shift circuit to ground; open circuit
cycle – page 8 pattern Pressure control solenoid 1 failure
P0750 TRANS Shift solenoid 1 circuit malfunction KOEO – page 3, or 2 A, M PCM Default: Shift solenoid 1 drive circuit: short circuit to ground
OBD II KOER – page 3, or – If short circuit to B+ V or or B+ V; high resistance; open circuit
open circuit – 3rd, 2nd, 3rd, Shift solenoid 1 failure
Comprehensive component
monitor transmission drive 4th, 5th shift pattern
cycle – page 8 – If short circuit to ground –
1st, 2nd, 3rd shift pattern
(Harsh shifts)
P0755 TRANS Shift solenoid 2 circuit malfunction KOEO – page 3, or 2 A, M PCM Default: Shift solenoid 2 drive circuit: short circuit to ground
OBD II KOER – page 3, or – If short circuit to B+ V or or B+ V; high resistance; open circuit
open circuit – 1st, 2nd, 4th, Shift solenoid 2 failure
Comprehensive component
monitor transmission drive 5th shift pattern
cycle – page 8 – If short circuit to ground –
3rd, 2nd, 3rd, 4th, 5th shift
pattern
(Harsh shifts)
P0760 TRANS Shift solenoid 3 circuit malfunction KOEO – page 3, or 2 A, M PCM Default: Shift solenoid 3 drive circuit: short circuit to ground
OBD II KOER – page 3, or – If short circuit to B+ V or or B+ V; high resistance; open circuit
open circuit – 1st, 3rd, 4th, Shift solenoid 3 failure
Comprehensive component
monitor transmission drive 5th shift pattern
cycle – page 8 – If short circuit to ground –
normal shift pattern
(Harsh shifts)
P0765 TRANS Shift solenoid 4 circuit malfunction KOEO – page 3, or N A, M PCM Default: Shift solenoid 4 drive circuit: short circuit to ground
JAG KOER – page 3, or – DRIVE – normal shift or B+ V; high resistance; open circuit
pattern Shift solenoid 4 failure
Comprehensive component
monitor transmission drive – Manual – 2, 3, 4 inhibited
cycle – page 8 (Harsh shifts)
P0775 TRANS Pressure control solenoid 2 stuck Comprehensive component 2 A, M PCM Default: Pressure control solenoid 2drive circuit: short
OBD II monitor transmission drive – 1st, 1st, 3rd, 4th, 4th shift circuit to ground; open circuit
cycle – page 8 pattern Pressure control solenoid 2 failure
P0779 TRANS Pressure control solenoid 2 drive KOEO – page 3, or N A, M PCM Default: Pressure control solenoid 2drive circuit intermittent
JAG circuit intermittent low voltage KOER – page 3, or – 1st, 1st, 3rd, 4th, 4th shift short circuit to ground
Comprehensive component pattern
monitor transmission drive
cycle – page 8
P0791 TRANS Intermediate speed sensor circuit Comprehensive component N A, M, T PCM Default: Intermediate speed sensor circuit: short circuit;
JAG monitor transmission drive – One-way clutch test high resistance; open circuit
cycle – page 8 inhibited Intermediate speed sensor failure
ABS/TCCM, DSCCM Default:
– traction control inhibited
(Harsh shifts)
P0794 TRANS Intermediate speed sensor sense Comprehensive component N A, M PCM Default: Intermediate speed sensor sense circuit
JAG circuit – intermittent signal monitor transmission drive – One-way clutch test intermittent: short circuit; high resistance; open
cycle – page 8 circuit
inhibited
Intermediate speed sensor failure
(Harsh shifts)
P0795 TRANS Pressure control solenoid 3 stuck Comprehensive component 2 A, M PCM Default: Pressure control solenoid 3drive circuit: short
OBD II monitor transmission drive – 1st, 2nd, 3rd gears only circuit to ground; open circuit
cycle – page 8 Pressure control solenoid 3 failure
P0796 TRANS Pressure control solenoid 3 circuit KOEO – page 3, or N A, M, T ABS/TCCM, DSCCM Default: Pressure control solenoid 3 drive circuit short
JAG high voltage KOER – page 3, or – traction control inhibited circuit to B+ V
Pressure control solenoid 3 failure
Comprehensive component
monitor transmission drive Transmission mechanical failure (other DTCs
cycle – page 8 logged)
(Harsh shifts)
P0797 TRANS Pressure control solenoid 3 circuit KOEO – page 3, or 2 A, M PCM Default: Pressure control solenoid 3 drive circuit short
OBD II low voltage KOER – page 3, or – 1st, 2nd, 3rd gears only circuit to ground
Pressure control solenoid 3 failure
Comprehensive component
monitor transmission drive Transmission mechanical failure (other DTCs
(Harsh shifts) logged)
cycle – page 8
P0799 TRANS Pressure control solenoid 3 drive KOEO – page 3, or N A, M PCM Default: Pressure control solenoid 3 drive circuit
JAG circuit intermittent low voltage KOER – page 3, or – 1st, 2nd, 3rd gears only intermittent short circuit to ground
Comprehensive component
monitor transmission drive
cycle – page 8
P0812 TRANS Reverse switch circuit malfunction KOER – page 3, or N N None Reverse switch to PCM signal circuit: open circuit,
JAG (Manual transmission) Drive vehicle; select Reverse high resistance, short circuit
gear Reverse pedal switch reference ground circuit
(from splice) open circuit
Reverse pedal switch failure
P0814 TRANS J Gate illumination circuit failure – Comprehensive component N N None PCM / J Gate illumination circuit(s): short circuit;
JAG gear selected monitor transmission drive open circuit
cycle – page 8 (PCM pins FH1-7, 8, 9)
P0840 TRANS Transmission pressure switch circuit KOEO – page 3, or N A, M PCM Default: Pressure switch to PCM signal circuit: short circuit;
JAG malfunction KOER – page 3, or – Manual 2nd, 3rd inhibited high resistance; open circuit
Pressure switch transmission internal circuit: short
Comprehensive component circuit; high resistance; open circuit
monitor transmission drive
cycle – page 8 Pressure switch failure
P1000 PCM OBD II System checks not complete KOEO – page 3, or N N None Refer to page 3
JAG since last memory clear KOER – page 3, or
Drive vehicle
P1001 PCM KOER not complete KOER – page 3 N N None Refer to page 3
JAG
P1100 EMS MAF Sensor signal intermittent Comprehensive component N N None MAF Sensor to PCM sensing circuit intermittent:
JAG monitor engine management open circuit, high resistance, short circuit
drive cycle – page 7 MAF Sensor supply circuit intermittent: open
circuit or short circuit
MAF Sensor failure
P1101 EMS MAF Sensor out of self test range KOEO – page 3, or N N None MAF Sensor to PCM sensing circuit: open circuit,
JAG KOER – page 3 high resistance, short circuit
MAF Sensor supply circuit: open circuit or short
circuit
MAF Sensor failure
P1112 EMS IAT Sensor signal intermittent Comprehensive component N N PCM Default: IAT Sensor to PCM sensing circuit intermittent:
JAG monitor engine management – IAT default value 38 °C open circuit, high resistance, short circuit
drive cycle – page 7 (100 °F) IAT Sensor reference ground circuit (to splice)
intermittent open circuit
IAT Sensor failure
P1116 V8 EMS ECT Sensor out of self test range KOEO – page 3, or N N PCM Default: IAT Sensor to PCM sensing circuit: open circuit,
JAG KOER – page 3 – ECT default value 102 °C high resistance, short circuit
(215 °F) IAT Sensor reference ground circuit (to splice) open
circuit
IAT Sensor failure
P1117 V8 EMS ECT Sensor signal intermittent Comprehensive component N N PCM Default: ECT Sensor to PCM sensing circuit intermittent:
JAG monitor engine management – ECT default value 102 °C open circuit, high resistance, short circuit
drive cycle – page 7 (215 °F) ECT Sensor reference ground circuit (to splice)
intermittent open circuit
ECT Sensor failure
P1121 EMS TP Sensor signals inconsistent with Comprehensive component 2 N None (as long as normal TP TP Sensors to PCM wiring harness fault
OBD II MAF Sensor signals monitor engine management signals are received) MAF Sensor to PCM wiring harness fault
drive cycle – page 7
TP Sensor(s) failure
MAF Sensor failure
P1122 EMS APP Sensor circuit low voltage – KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “1” (sensor pin
JAG APP1 KOER – page 3, or signals are received from 5) open circuit or high resistance
remaining sensors) APP Sensor reference voltage (sensor pin 10) open
Comprehensive component circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1123 EMS APP Sensor circuit high voltage – KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “1” (sensor pin
JAG APP1 KOER – page 3, or signals are received from 5) short circuit to high voltage
remaining sensors) APP Sensor reference ground (sensor pin 9) open
Comprehensive component circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1124 EMS TP Sensor out of self test range KOEO – page 3, or N N None (as long as normal TP One or more individual TP Sensors to PCM sensing
JAG KOER – page 3, or signals are received) circuits: open circuit, high resistance, short
circuit to ground or high voltage
Drive vehicle TP Sensor failure
P1127 EMS Exhaust not warm enough; Heated oxygen sensors N N None Engine not at normal operating temperature
JAG downstream HO2 Sensors not tested monitor drive cycle – page 4 Exhaust system leak / failure
P1128 EMS Upstream HO2 Sensors swapped Heated oxygen sensors N N None Upstream HO2 Sensors swapped from bank to
JAG from bank to bank monitor drive cycle – page 4 bank
Upstream HO2 Sensors to PCM wiring fault
P1129 EMS Downstream HO2 Sensors swapped Heated oxygen sensors N N None Downstream HO2 Sensors swapped from bank to
JAG from bank to bank monitor drive cycle – page 4 bank
Downstream HO2 Sensors to PCM wiring fault
P1130 EMS Lack of HO2 Sensor swing, adaptive Heated oxygen sensors 2 N None HO2 Sensor 1/1 disconnected
OBD II fuel at limit – bank 1, upstream (1/1) monitor drive cycle – page 4 HO2 Sensor 1/1 to PCM wiring fault
Engine induction air leak between MAF Sensor and
throttle
Exhaust system leak
Contaminated fuel
Fuel in engine oil
Engine misfire
HO2 Sensor 1/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1131 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or 2 N None HO2 Sensor 1/1 to PCM wiring fault
OBD II indicates lean – bank 1, upstream Heated oxygen sensors Engine induction air leak between MAF Sensor and
(1/1) monitor drive cycle – page 4 throttle
Exhaust system leak
HO2 Sensor 1/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1132 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or 2 N None HO2 Sensor 1/1 to PCM wiring fault
OBD II indicates rich – bank 1, upstream Heated oxygen sensors Exhaust system restriction
(1/1) monitor drive cycle – page 4 Contaminated fuel
Fuel in engine oil
HO2 Sensor 1/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1133 EMS Bank 1 fuel metering control shifted Comprehensive component 2 N None Temporary contamination of HO2 Sensor 1/1
OBD II lean monitor engine management causing “lean drift”
drive cycle – page 7 Temporary contamination of HO2 Sensor 1/2
causing “rich drift”
Engine misfire
HO2 Sensors 1/1 and 1/2 to PCM wiring fault(s)
Engine induction air leak between MAF Sensor and
throttle
Exhaust system leak
Water in bank 1 spark plug well(s)
HO2 Sensors 1/1 and/or 1/2 failure
P1134 EMS Bank 1 fuel metering control shifted Comprehensive component 2 N None Temporary contamination of HO2 Sensor 1/1
OBD II rich monitor engine management causing “rich drift”
drive cycle – page 7 Temporary contamination of HO2 Sensor 1/2
causing “lean drift”
Engine misfire
HO2 Sensors 1/1 and 1/2 to PCM wiring fault(s)
Exhaust system restriction
Water in bank 1 spark plug well(s)
HO2 Sensors 1/1 and/or 1/2 failure
P1135 EMS APP Sensor signal intermittent – KOEO – page 3, or N N None (as long as normal APP APP Sensor to PCM sensing circuit “1” (sensor pin
JAG APP1 KOER – page 3, or signals are received from 5) intermittent: open circuit, high resistance,
remaining sensors) short circuit
Comprehensive component APP Sensor reference voltage (sensor pin 10)
monitor engine management intermittent open circuit
drive cycle – page 7
APP Sensor reference ground (sensor pin 9)
intermittent open circuit
APP Sensor failure
P1137 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or N N None HO2 Sensor 1/2 to PCM wiring fault
JAG indicates lean – bank 1, downstream Heated oxygen sensors HO2 Sensor 1/2 failure
(1/2) monitor drive cycle – page 4
P1138 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or N N None HO2 Sensor 1/2 to PCM wiring fault
JAG indicates rich – bank 1, downstream Heated oxygen sensors HO2 Sensor 1/2 failure
(1/2) monitor drive cycle – page 4
P1150 EMS Lack of HO2 Sensor swing, adaptive Heated oxygen sensors 2 N None HO2 Sensor 2/1 disconnected
OBD II fuel at limit – bank 2, upstream (2/1) monitor drive cycle – page 4 HO2 Sensor 2/1 to PCM wiring fault
Engine induction air leak between MAF Sensor and
throttle
Exhaust system leak
Contaminated fuel
Fuel in engine oil
Engine misfire
HO2 Sensor 1/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1151 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or 2 N None HO2 Sensor 2/1 to PCM wiring fault
OBD II indicates lean – bank 2, upstream Heated oxygen sensors Engine induction air leak between MAF Sensor and
(2/1) monitor drive cycle – page 4 throttle
Exhaust system leak
HO2 Sensor 2/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1152 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or 2 N None HO2 Sensor 2/1 to PCM wiring fault
OBD II indicates rich – bank 2, upstream Heated oxygen sensors Exhaust system restriction
(2/1) monitor drive cycle – page 4 Contaminated fuel
Fuel in engine oil
HO2 Sensor 2/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1153 EMS Bank 2 fuel metering control shifted Comprehensive component 2 N None Temporary contamination of HO2 Sensor 2/1
OBD II lean monitor engine management causing “lean drift”
drive cycle – page 7 Temporary contamination of HO2 Sensor 2/2
causing “rich drift”
Engine misfire
HO2 Sensors 2/1 and 2/2 to PCM wiring fault(s)
Engine induction air leak between MAF Sensor and
throttle
Exhaust system leak
Water in bank 2 spark plug well(s)
HO2 Sensors 2/1 and/or 2/2 failure
P1154 EMS Bank 2 fuel metering control shifted Comprehensive component 2 N None Temporary contamination of HO2 Sensor 2/1
OBD II rich monitor engine management causing “rich drift”
drive cycle – page 7 Temporary contamination of HO2 Sensor 2/2
causing “lean drift”
Engine misfire
HO2 Sensors 2/1 and 2/2 to PCM wiring fault(s)
Exhaust system restriction
Water in bank 2 spark plug well(s)
HO2 Sensors 2/1 and/or 2/2 failure
P1157 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or N N None HO2 Sensor 2/2 to PCM wiring fault
JAG indicates lean – bank 2, downstream Heated oxygen sensors HO2 Sensor 2/2 failure
(2/2) monitor drive cycle – page 4
P1158 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or N N None HO2 Sensor 2/2 to PCM wiring fault
JAG indicates rich – bank 2, downstream Heated oxygen sensors HO2 Sensor 2/2 failure
(2/2) monitor drive cycle – page 4
P1183 EMS EOT Sensor circuit malfunction Comprehensive component 2 N PCM Default: EOT Sensor to PCM sensing circuit: open circuit,
OBD II monitor engine management – V6 CHT substituted high resistance, short circuit
drive cycle – page 7 EOT Sensor reference ground circuit (to splice)
– V8 ECT substituted open circuit
EOT Sensor failure
P1184 EMS EOT Sensor out of self test range KOEO – page 3, or N N PCM Default: EOT Sensor to PCM sensing circuit high resistance
JAG KOER – page 3 – V6 CHT substituted when hot
EOT Sensor to PCM sensing circuit intermittent
– V8 ECT substituted high resistance
EOT Sensor failure
P1214 EMS APP Sensor signal intermittent – KOEO – page 3, or N N None (as long as normal APP APP Sensor to PCM sensing circuit “2” (sensor pin
JAG APP2 KOER – page 3, or signals are received from 4) intermittent: open circuit, high resistance,
remaining sensors) short circuit
Comprehensive component APP Sensor reference voltage (sensor pin 8)
monitor engine management intermittent open circuit
drive cycle – page 7
APP Sensor reference ground (sensor pin 6)
intermittent open circuit
APP Sensor failure
P1215 EMS APP Sensor circuit low voltage – KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “3” (sensor pin
JAG APP3 KOER – page 3, or signals are received from 7) open circuit or high resistance
remaining sensors) APP Sensor reference voltage (sensor pin 3) open
Comprehensive component circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1216 EMS APP Sensor circuit high voltage – KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “1” (sensor pin
JAG APP3 KOER – page 3, or signals are received from 7) short circuit to high voltage
remaining sensors) APP Sensor reference ground (sensor pin 2) open
Comprehensive component circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1217 EMS APP Sensor signal intermittent – KOEO – page 3, or N N None (as long as normal APP APP Sensor to PCM sensing circuit “3” (sensor pin
JAG APP3 KOER – page 3, or signals are received from 7) intermittent: open circuit, high resistance,
remaining sensors) short circuit
Comprehensive component APP Sensor reference voltage (sensor pin 3)
monitor engine management intermittent open circuit
drive cycle – page 7
APP Sensor reference ground (sensor pin 2)
intermittent open circuit
APP Sensor failure
P1222 EMS APP Sensor circuit low voltage – KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “2” (sensor pin
JAG APP2 KOER – page 3, or signals are received from 4) open circuit or high resistance
remaining sensors) APP Sensor reference voltage (sensor pin 8) open
Comprehensive component circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1223 EMS APP Sensor circuit high voltage – KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “2” (sensor pin
JAG APP2 KOER – page 3, or signals are received from 4) short circuit to high voltage
remaining sensors) APP Sensor reference ground (sensor pin 6) open
Comprehensive component circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1233 EMS Fuel delivery system disabled or KOEO – page 3, or N N None PCM to RECM fuel pump drive signal circuit (PCM
JAG inoperative KOER – page 3, or pin FH1-58): open circuit, high resistance, short
circuit
Comprehensive component RECM to fuel pump drive circuit: open circuit, high
monitor engine management resistance, short circuit
drive cycle – page 7
(Engine shut off) Fuel pump relay power supply open circuit, short
circuit
Fuel pump relay to RECM power supply circuit
open circuit
Fuel pump relay failure
P1235 EMS Fuel pump control out of range KOER – page 3, or N N None PCM to RECM fuel pump drive signal circuit (PCM
JAG Comprehensive component pin FH1-58) intermittent: open circuit, high
resistance, short circuit
monitor engine management (Engine running too rich /
drive cycle – page 7 RECM to fuel pump drive circuit intermittent: open
lean) circuit, high resistance, short circuit
P1237 EMS Fuel pump secondary circuit KOER – page 3, or N N None RECM to fuel pump drive circuit: open circuit, high
JAG malfunction Comprehensive component resistance, short circuit
monitor engine management Fuel pump relay power supply open circuit, short
drive cycle – page 7 circuit
(Engine shut off) Fuel pump relay to RECM power supply circuit
open circuit
Fuel pump relay failure
P1246 EMS Generator load input to PCM failure KOER – page 3 N M, C None Accessory drive belt failure
JAG PCM to generator load circuit (PCM pin PI1-50):
open circuit, high resistance, short circuit
Generator failure
P1260 EMS Vehicle theft detected – engine KOEO – page 3 N N None Invalid ignition key code
JAG disabled Passive anti-theft system (PATS) signal to
(PCM SCP input from PATS, INST, instrument pack missing or corrupted
GECM) PATS SCP message failure
P1270 EMS Engine speed or vehicle speed limit Operate vehicle N N None Engine speed limit reached
JAG reached Vehicle speed limit reached
P1285 V6 EMS Cylinder head over temperature KOEO – page 3, or N M, H PCM Default: Coolant level low / leak
JAG sensed KOER – page 3, or – fail-safe cooling strategy Coolant contaminated
Comprehensive component Cooling system thermostat defective
monitor engine management Excessive load on engine – high elevation, steep
drive cycle – page 7 grade, trailer towing
P1288 V6 EMS CHT Sensor out of self test range KOEO – page 3, or N N PCM Default: Engine not at normal operating temperature
JAG KOER – page 3 – CHT default value 102 °C Engine overheat condition – refer to P1285
(215 °F) CHT Sensor disconnected
CHT Sensor to PCM circuit fault
PCM cooling fan circuit failure
Cooling fan module to fan motor circuit failure
Cooling fan module failure
P1289 V6 EMS CHT Sensor sense circuit high KOEO – page 3, or N N PCM Default: CHT Sensor to cylinder head poor contact
JAG voltage (low temperature) KOER – page 3, or – CHT default value 102 °C CHT Sensor to PCM sensing circuit high resistance,
(215 °F) open circuit or short circuit to high voltage
Comprehensive component
DTC P0118 flagged for OBD II monitor engine management CHT Sensor failure
drive cycle – page 7
P1290 V6 EMS CHT Sensor sense circuit low voltage KOEO – page 3, or N N PCM Default: Engine overheat condition – refer to P1285
JAG (high temperature) KOER – page 3, or – CHT default value 102 °C CHT Sensor to PCM wiring short circuit to ground
Comprehensive component (215 °F) CHT Sensor failure
DTC P0117 flagged for OBD II monitor engine management
drive cycle – page 7
P1299 V6 EMS Fail-safe cooling mode active Comprehensive component 1 M, H PCM Default: Engine overheat condition – refer to P1285
OBD II monitor engine management – fail-safe cooling strategy PCM cooling fan circuit failure
drive cycle – page 7
Cooling fan module to fan motor circuit failure
Cooling fan module failure
P1309 EMS Misfire monitor failure Misfire monitor drive cycle – 2 N None CKP Sensor fault – refer to P0320
OBD II page 4 CMP Sensor(s) fault – refer to P0340, P0341
PCM failure
P1380 EMS VVT Solenoid circuit malfunction – KOEO – page 3, or 2 N None Bank 1 VVT solenoid valve disconnected
OBD II bank 1 KOER – page 3, or Bank 1 VVT solenoid valve to PCM PWM drive
circuit fault
Comprehensive component
monitor engine management Bank 1 VVT solenoid valve power supply circuit
drive cycle – page 7 fault
Bank 1 VVT solenoid failure
P1381 EMS VVT Over advanced – bank 1 KOER – page 3, or 2 N None Bank 1 VVT solenoid valve to PCM PWM drive
OBD II Comprehensive component circuit fault
monitor engine management Bank 1 VVT actuator oil supply fault
drive cycle – page 7 Bank 1 VVT actuator stuck
P1383 EMS VVT Over retarded – bank 1 KOER – page 3, or 2 N None Bank 1 VVT solenoid valve to PCM PWM drive
OBD II Comprehensive component circuit fault
monitor engine management Bank 1 VVT actuator oil supply fault
drive cycle – page 7 Bank 1 VVT actuator stuck
P1385 EMS VVT Solenoid circuit malfunction – KOEO – page 3, or 2 N None Bank 2 VVT solenoid valve disconnected
OBD II bank 2 KOER – page 3, or Bank 2 VVT solenoid valve to PCM PWM drive
circuit fault
Comprehensive component
monitor engine management Bank 2 VVT solenoid valve power supply circuit
drive cycle – page 7 fault
Bank 2 VVT solenoid failure
P1386 EMS VVT Over advanced – bank 2 KOER – page 3, or 2 N None Bank 2 VVT solenoid valve to PCM PWM drive
OBD II Comprehensive component circuit fault
monitor engine management Bank 2 VVT actuator oil supply fault
drive cycle – page 7 Bank 2 VVT actuator stuck
P1388 EMS VVT Over retarded – bank 2 KOER – page 3, or 2 N None Bank 2 VVT solenoid valve to PCM PWM drive
OBD II Comprehensive component circuit fault
monitor engine management Bank 2 VVT actuator oil supply fault
drive cycle – page 7 Bank 2 VVT actuator stuck
P1400 V6 EMS DPFE Sensor circuit low voltage KOEO – page 3, or 2 N None DPFE Sensor reference voltage circuit (to splice)
OBD II KOER – page 3, or open circuit
DPFE Sensor to PCM sensing circuit; open circuit,
EGR monitor drive cycle – high resistance, short circuit to ground
page 6
DPFE Sensor failure
P1401 V6 EMS DPFE Sensor circuit high voltage KOEO – page 3, or 2 N None DPFE Sensor reference ground circuit (to splice)
OBD II KOER – page 3, or open circuit
DPFE Sensor to PCM sensing circuit short circuit to
EGR monitor drive cycle – high voltage
page 6
DPFE Sensor failure
P1405 V6 EMS DPFE Sensor upstream hose – no EGR monitor drive cycle – 2 N None Upstream hose disconnected, restricted, broken
OBD II flow page 6
P1406 V6 EMS DPFE Sensor downstream hose – no EGR monitor drive cycle – 2 N None Downstream hose disconnected, restricted,
OBD II flow page 6 broken
P1408 V6 EMS EGR Flow out of self test range KOER – page 3, or N N None DPFE Sensor reference voltage circuit (to splice)
JAG EGR monitor drive cycle – open circuit
page 6 DPFE Sensor failure
P1409 V6 EMS EGR Vacuum regulator circuit KOEO – page 3, or 2 N None EGR Vacuum regulator to PCM drive circuit: open
OBD II malfunction KOER – page 3, or circuit, high resistance, short circuit
EGR Vacuum regulator power supply circuit: open
EGR monitor drive cycle – circuit, short circuit
page 6
EGR Vacuum regulator failure
P1443 EMS EVAP Canister purge valve circuit Evaporative system monitor 2 N None EVAP Canister purge valve to PCM drive circuit:
OBD II malfunction drive cycle – page 6 open circuit, high resistance, short circuit
EVAP Canister purge valve power supply circuit:
open circuit, short circuit
EVAP Canister purge valve failure
P1450 EMS System unable to bleed-up fuel tank Evaporative system monitor 2 N None Restricted vapor piping – fuel tank to EVAP canister
OBD II vacuum drive cycle – page 6 purge valve
EVAP Canister purge valve stuck open
P1451 EMS EVAP Canister close valve circuit KOEO – page 3, or 2 N None EVAP Canister close valve to PCM drive circuit:
OBD II malfunction KOER – page 3, or open circuit, high resistance, short circuit
EVAP Canister close valve power supply circuit:
Evaporative system monitor open circuit, short circuit
drive cycle – page 6
EVAP Canister close valve failure
P1460 EMS A/C compressor cut-out malfunction KOEO – page 3, or N N None PCM to A/C compressor clutch relay circuit: open
JAG KOER – page 3, or circuit, short circuit
A/C compressor clutch relay to A/C compressor
Comprehensive component (PCM inhibits A/C clutch circuit: open circuit, short circuit
monitor engine management engagement during: engine
drive cycle – page 7 cranking, wide open throttle, A/C compressor clutch relay failure
throttle limp home mode) A/C compressor clutch ground circuit open circuit
A/C compressor clutch failure
P1461 EMS A/C Pressure sensor high voltage KOEO – page 3, or N N None A/C Pressure sensor to PCM wiring (supply, sense,
JAG (high pressure) KOER – page 3, or reference ground) short circuit to each other
A/C Pressure sensor to PCM sensing circuit short
Comprehensive component circuit to high voltage
monitor engine management
drive cycle – page 7 A/C Pressure sensor failure
P1462 EMS A/C Pressure sensor low voltage (low KOEO – page 3, or N N None A/C Pressure sensor to PCM sensing circuit open
JAG pressure) KOER – page 3, or circuit or short circuit to ground
A/C Pressure sensor to PCM reference voltage
Comprehensive component circuit open circuit or short circuit to ground
monitor engine management
drive cycle – page 7 A/C Pressure sensor to PCM reference ground
circuit open circuit
A/C Pressure sensor failure
P1463 EMS Air conditioning system insufficient Comprehensive component N N None A/C Refrigerant charge low
JAG refrigerant pressure charge monitor engine management A/C Refrigeration system leak
drive cycle – page 7
A/C Pressure sensor to PCM wiring fault
A/C Pressure sensor failure
A/C Compressor failure
P1464 EMS A/C Pressure sensor out of self test KOEO – page 3, or N N None A/C Pressure sensor to PCM wiring fault
JAG range KOER – page 3 A/C Pressure sensor failure
P1474 EMS Radiator cooling fan control circuit KOEO – page 3, or N N None PCM to cooling fan module circuit: open circuit,
JAG malfunction KOER – page 3, or high resistance, short circuit
Cooling fan module failure
Comprehensive component
monitor engine management
drive cycle – page 7
P1506 EMS Idle air control over speed error KOER – page 3 2 N None Intake manifold air leak
OBD II PCM / TACM circuit fault
TACM failure
Throttle failure
P1507 EMS Idle air control under speed error KOER – page 3 2 N None Engine air filter restricted / defective
OBD II Engine air intake restricted / damaged
PCM / TACM circuit fault
TACM failure
Throttle failure
P1532 V6 EMS IMT Valve control circuit malfunction KOEO – page 3, or N N None IMT Valve (top) disconnected
JAG – top valve Comprehensive component IMT Valve (top) to PCM drive circuit fault
monitor engine management IMT Valve (top) power supply circuit fault
drive cycle – page 7
IMT Valve (top) failure
P1534 EMS Air bag(s) deployed (Restraints KOEO – page 3 N A, M PCM to RCM airbag deployed circuit: open circuit,
JAG control module (RCM) input to PCM) high resistance, short circuit to ground
circuit malfunction RCM fault
P1549 V6 EMS IMT Valve control circuit malfunction KOEO – page 3, or N N None IMT Valve (bottom) disconnected
JAG – bottom valve Comprehensive component IMT Valve (bottom) to PCM drive circuit fault
monitor engine management IMT Valve (bottom) power supply circuit fault
drive cycle – page 7
IMT Valve (bottom) failure
P1565 EMS Speed control command switch input Drive vehicle; operate all speed N M, S PCM Default: Speed control steering wheel switches to PCM
JAG (steering wheel switches) out of control steering wheel – speed control inhibited signal circuit (PCM pin FH1-57): short circuit to
range – high voltage switches B+ V
Speed control steering wheel switche(s) failure
P1566 EMS Speed control command switch input Drive vehicle; operate all speed N M, S PCM Default: Speed control steering wheel switches to PCM
JAG (steering wheel switches) out of control steering wheel – speed control inhibited wiring: open circuit, high resistance, short circuit
range – low voltage switches to ground
Speed control steering wheel switche(s) failure
P1572 EMS Brake cancel switch out of self test Ignition ON; operate brake N M, S PCM Default: Brake cancel switch to PCM signal circuit: open
JAG range pedal – speed control inhibited circuit, high resistance, short circuit
Brake cancel switch power supply circuit: open
circuit, short circuit
Brake cancel switch failure
P1573 EMS TP Sensor signals malfunction – more KOEO – page 3, or 2 R, M Throttle limp home mode: TP Sensor to PCM sensing circuits (sensor pins 1,
OBD II than one signal failure KOER – page 3, or – high idle speed 2, 10): open circuit, high resistance, short circuit
TP Sensor to PCM reference voltage circuits
Comprehensive component – no accelerator pedal (sensor pins 4, 3): open circuit, high resistance,
monitor engine management response short circuit
drive cycle – page 7
TP Sensor to PCM reference ground circuits
(sensor pins 6, 7): open circuit, high resistance,
short circuit
TP Sensor failure
P1574 EMS TP Sensor signals disagree – one KOEO – page 3, or N A, M None (as long as normal Refer to P1573 Possible Causes
JAG signal failure KOER – page 3, or signals are received from the
remaining two sensors)
Comprehensive component
monitor engine management
drive cycle – page 7
P1576 EMS APP Sensor signals malfunction – KOEO – page 3, or 2 R, M Throttle limp home mode: APP Sensor to PCM sensing circuits (sensor pins 4,
OBD II more than one signal failure KOER – page 3, or – high idle speed 5, 7): open circuit, high resistance, short circuit
APP Sensor to PCM reference voltage circuits
Comprehensive component – no accelerator pedal (sensor pins 3, 8, 10): open circuit, high
monitor engine management response resistance, short circuit
drive cycle – page 7
APP Sensor to PCM reference ground circuits
(sensor pins 2, 6, 9): open circuit, high resistance,
short circuit
APP Sensor failure
P1577 EMS APP Sensor signals disagree – one KOEO – page 3, or N A, M None (as long as normal Refer to P1576 Possible Causes
JAG signal failure KOER – page 3, or signals are received from the
remaining two sensors)
Comprehensive component
monitor engine management
drive cycle – page 7
P1580 EMS PCM Override of internal throttle KOEO – page 3, or 2 R, M Throttle limp home mode: TP Sensor circuit fault – TP Sensor DTC(s) flagged
OBD II monitor KOER – page 3, or – high idle speed Throttle circuit fault – throttle DTC(s) flagged
Comprehensive component – no accelerator pedal
monitor engine management response
drive cycle – page 7 (Engine may stop if fuel
injection is canceled)
P1581 EMS PCM Throttle monitor malfunction KOEO – page 3, or N R, M PCM Default: PCM Failure
JAG KOER – page 3, or – cruise control inhibited
Comprehensive component – reverse gear power limiting
monitor engine management inhibited
drive cycle – page 7
P1582 EMS Throttle data recorder data available KOEO – page 3, or N N None Vehicle impact
JAG KOER – page 3, or To reuse PCM:
Comprehensive component – 100 Ignition key cycles, then
monitor engine management – Clear DTC using PDU, or
drive cycle – page 7
– Additional 40 ignition key cycles
P1583 EMS Speed control inhibited by PCM KOEO – page 3, or N A, M None TP Sensor circuit fault – TP Sensor DTC(s) flagged
JAG throttle monitor KOER – page 3, or Throttle circuit fault – throttle DTC(s) flagged
Comprehensive component
monitor engine management
drive cycle – page 7
P1584 EMS Throttle actuation malfunction KOEO – page 3, or 2 A, M None Throttle body failure
OBD II KOER – page 3, or (Engine will stall at low
Comprehensive component throttle angles)
monitor engine management
drive cycle – page 7
P1585 EMS TACM malfunction KOEO – page 3, or 2 R, M None PCM to TACM redundant control circuits (TACM
OBD II KOER – page 3, or (Engine will stop – or possibly pins 2, 3): open circuit, high resistance, short
circuit
Comprehensive component run at very low idle speed)
TACM ground circuits: open circuit, high resistance
monitor engine management
drive cycle – page 7 TACM Failure
P1586 EMS TACM to PCM communication (SCP) KOEO – page 3, or 2 A, M None SCP circuit fault – U Code flagged
OBD II failure KOER – page 3, or TACM Failure
Comprehensive component
monitor engine management
drive cycle – page 7
P1587 EMS PCM to TACM throttle command KOEO – page 3, or 2 R*, M If only one command circuit PCM to TACM redundant control circuits (TACM
OBD II redundancy circuit malfunction KOER – page 3, or fails: None pins 2, 3): open circuit, high resistance, short
circuit
Comprehensive component If both command circuits fail:
monitor engine management Throttle limp home mode
drive cycle – page 7 – high idle speed
– no accelerator pedal
response
R* If both command circuits
fail
P1589 EMS Throttle valve angle does not match KOEO – page 3, or 2 R None Throttle failure
OBD II desired angle KOER – page 3, or (Engine will stop – or possibly
Comprehensive component run at very low idle speed)
monitor engine management
drive cycle – page 7
P1633 PCM Keep alive memory (KAM) voltage Drive vehicle 1 N None Vehicle battery voltage low
OBD II too low Battery power supply to PCM interrupted for longer
than 20 seconds during engine operation
P1635 EMS Wheel / axle ratio out of acceptable Drive vehicle N N None Incorrect size tire(s) fitted to vehicle
JAG range Incorrect size wheel(s) fitted to vehicle
P1636 PCM PCM Internal communication error Comprehensive component 2 N PCM Default: PCM Failure
OBD II monitor engine management – self test partially inhibited
drive cycle – page 7
P1650 EMS PSP Switch out of self test range KOEO – page 3, or N N None PSP switch to PCM signal circuit: open circuit, high
JAG KOER – page 3 resistance, short circuit
PSP switch reference ground circuit (to splice):
open circuit
PSP switch failure
P1651 EMS PSP Switch circuit malfunction Drive vehicle N N None PSP switch to PCM signal circuit: open circuit, high
JAG resistance, short circuit
PSP switch reference ground circuit (to splice):
open circuit
PSP switch failure
P1700 TRANS Transmission intermediate failure KOEO – page 3, or N N PCM Default: Clear DTC 1700
JAG KOER – page 3, or – 2nd and 5th gears only Diagnose and repair other flagged DTCs
Comprehensive component Conduct drive cycle – if P1700 reflags: transmission
monitor transmission drive mechanical failure (direct one-way clutch)
cycle – page 8
P1702 TRANS Range sensor circuit intermittent KOEO – page 3, or N N PCM Defaults to DRIVE (to Gear selector cable incorrectly adjusted
JAG malfunction KOER – page 3, or maintain all five gears) Range sensor circuit intermittent: open circuit;
J Gate gear selected short circuit
Comprehensive component
monitor transmission drive illumination extinguished Range sensor failure
cycle – page 8 (Harsh shifts)
P1704 TRANS Range sensor circuit not indicating P KOEO – page 3, or N T ABS/TCCM, DSCCM Default: Selector not in P / N
JAG / N during self test KOER – page 3 – traction control inhibited Range sensor incorrect alignment
Gear selector cable incorrectly adjusted
Gear selector mechanical failure
Range sensor failure
P1705 TRANS Range sensor out of self test range KOEO – page 3, or N N None Range sensor incorrect alignment
JAG KOER – page 3 Gear selector cable incorrectly adjusted
Gear selector mechanical failure
Range sensor failure
P1711 TRANS TFT Out of self test range KOEO – page 3, or N T ABS/TCCM, DSCCM Default: Transmission not at normal operating temperature
JAG KOER – page 3 – traction control inhibited TFT Sense circuit: short circuit; high resistance;
open circuit
TFT Sensor failure
P1713 TRANS TFT Signal – no change at low range Comprehensive component N T PCM Default: TFT Sensor circuit: high resistance; open circuit
JAG during vehicle operation monitor transmission drive – TFT calculated from TFT Sensor failure
cycle – page 8 ECT (V8) / CHT (V6)
ABS/TCCM, DSCCM Default:
– traction control inhibited
P1714 TRANS Shift solenoid 1 stuck – mechanical Comprehensive component 2 A, M PCM Default: Shift solenoid 1 mechanical failure
OBD II failure monitor transmission drive – 1st, 2nd, 3rd shift pattern
cycle – page 8 or
– 3rd, 2nd, 3rd, 4th, 5th shift
pattern
(Shift pattern depends on
position of stuck solenoid)
P1715 TRANS Shift solenoid 2 stuck – mechanical Comprehensive component 2 A, M PCM Default: Shift solenoid 2 mechanical failure
OBD II failure monitor transmission drive – 1st, 2nd, 4th, 5th shift
cycle – page 8 pattern or
– 3rd, 2nd, 3rd, 4th, 5th shift
pattern
(Shift pattern depends on
position of stuck solenoid)
P1716 TRANS Shift solenoid 3 stuck – mechanical Comprehensive component 2 A, M PCM Default: Shift solenoid 3 mechanical failure
OBD II failure monitor transmission drive – 1st, 1st, 3rd, 4th, 5th shift
cycle – page 8 pattern or
– normal shift pattern
(Shift pattern depends on
position of stuck solenoid)
P1717 TRANS Shift solenoid 4 stuck – mechanical Comprehensive component N A, M PCM Default: Shift solenoid 4 mechanical failure
JAG failure monitor transmission drive – DRIVE – normal shift
cycle – page 8 pattern
– Manual – 2, 3, 4 inhibited
P1718 TRANS TFT Signal – no change at high range Comprehensive component N T PCM Default: TFT Sensor circuit short circuit
JAG during vehicle operation monitor transmission drive – TFT calculated from TFT Sensor failure
cycle – page 8 ECT (V8) / CHT (V6)
ABS/TCCM, DSCCM Default:
– traction control inhibited
P1740 TRANS TCC solenoid stuck – mechanical Comprehensive component 2 A, M None TCC solenoid mechanical failure
OBD II failure monitor transmission drive (TCC applied / released
cycle – page 8 depending on position of
stuck solenoid)
P1746 TRANS Pressure control solenoid 1 circuit KOEO – page 3, or N A, M, T PCM Default: Pressure control solenoid 1 drive circuit short
JAG low voltage KOER – page 3, or – normal shift pattern circuit to ground
Pressure control solenoid 1 failure
Comprehensive component
monitor transmission drive Transmission mechanical failure (other DTCs
(Harsh shifts) logged)
cycle – page 8
P1747 TRANS Pressure control solenoid 1 circuit KOEO – page 3, or 2 A, M PCM Default: Pressure control solenoid 1 drive circuit: short
OBD II high voltage KOER – page 3, or – 1st, 2nd, 4th, 5th shift circuit to B+ V; open circuit
pattern Pressure control solenoid 1 failure
Comprehensive component
monitor transmission drive Transmission mechanical failure (other DTCs
cycle – page 8 logged)
(Harsh shifts)
P1760 TRANS Pressure control solenoid 1 drive KOEO – page 3, or N A, M PCM Default: Pressure control solenoid 1 drive circuit
JAG circuit intermittent low voltage KOER – page 3, or – 1st, 2nd, 4th, 5th shift intermittent short circuit to ground
Comprehensive component pattern
monitor transmission drive
cycle – page 8
P1780 TRANS D – 4th switch out of self test range KOEO – page 3, or 2 A, M PCM Default: D – 4th Switch power supply open circuit
OBD II KOER – page 3, or – Manual 4th inhibited D – 4th Switch / PCM sense circuit: short circuit;
high resistance; open circuit
Comprehensive component
monitor transmission drive D – 4th Switch failure
cycle – page 8
P1783 TRANS Transmission over temperature Comprehensive component N T PCM Default: Excessive vehicle load
JAG condition indicated – >127 °C (270 °F) monitor transmission drive – TCC Lock-up in all gears Transmission fluid level low
cycle – page 8
ABS/TCCM, DSCCM Default: Transmission fluid contaminated
– traction control inhibited Transmission fluid cooler failure (clogged)
TFT Sensor fault – refer to P0712
P1788 TRANS Pressure control solenoid 2 circuit KOEO – page 3, or N T PCM Default: Pressure control solenoid 2 drive circuit: short
JAG high voltage KOER – page 3, or – normal shift pattern circuit to B+ V; open circuit
Pressure control solenoid 2 failure
Comprehensive component ABS/TCCM, DSCCM Default:
monitor transmission drive Transmission mechanical failure (other DTCs
– traction control inhibited logged)
cycle – page 8
(Harsh shifts)
P1789 TRANS Pressure control solenoid 2 drive KOEO – page 3, or 2 A, M PCM Default: Pressure control solenoid 2 drive circuit short
OBD II circuit low voltage KOER – page 3, or – 1st, 1st, 3rd, 4th, 4th shift circuit to ground
pattern Pressure control solenoid 2 failure
Comprehensive component
monitor transmission drive Transmission mechanical failure (other DTCs
cycle – page 8 logged)
(Harsh shifts)
P1881 V8 EMS Engine coolant level sensor circuit KOEO – page 3, or N N None Low coolant level
JAG malfunction KOER – page 3, or Coolant level sensor to PCM signal circuit: open
circuit, high resistance, short circuit
Comprehensive component
monitor engine management Coolant level sensor power supply circuit: open
drive cycle – page 7 circuit, short circuit
Coolant level sensor ground circuit: open circuit,
high resistance
Coolant level sensor failure
SYS The powertrain system the DTC is associated with – EMS, TRANS, PCM, ABS/TC (DSC).
DTC retrieval tools:
OBD II – indicates that the DTC is an OBD II code and can be accessed via a generic scan tool or PDU / WDS.
JAG – indicates that the DTC is not an OBD II code and is accessed only via PDU / WDS.
CHECK ENGINE MIL 1 1 TRIP – indicates that the CHECK ENGINE MIL is activated by a fault occurring during ONE “TRIP”.
(CK ENG) 2 2 TRIPS – indicates that the CHECK ENGINE MIL is activated by a fault occurring during TWO CONSECUTIVE “TRIPS”.
N NO – indicates that the CHECK ENGINE MIL is not activated.
POSSIBLE CAUSES Possible causes are listed in the order of diagnostic checking.
HIGH VOLTAGE – High voltage can be either sensor supply voltage (5 volts) or B+ voltage.
SELF TESTS
Two technician initiated component self tests are available using PDU / WDS:
KOEO Key (ignition) On Engine Off – The KOEO self test determines if system components are operating within tolerances with the ignition switched ON and
the engine stopped.
KOER Key (ignition) On Engine Running – The KOER self test determines if system components are operating within tolerances with the ignition switched on
and the engine running. KOER flags self-test DTC P1001 if a component fails to operate within the specified limits but does not activate the CHECK ENGINE MIL.
V8 V6
AM IMAF AM IMAF
Stage 1 15.9 – 19.7 grams per second 3.15 v – 3.40 v 15.9 – 19.7 grams per second 3.40 v – 3.70 v
Stage 2 21.2 – 24.2 grams per second 3.50 v – 3.80 v 21.9 – 25.7 grams per second 3.90 v – 4.25 v
1 Start engine.
2 Move transmission mode switch between Normal and Sport. Verify switch state illumination.
3 Move the gear selector to all positions in the J Gate for five (5) seconds each. Verify the state illumination in each position.
4 Drive vehicle to bring the transmission fluid temperature up to normal operating temperature.
5 Stop vehicle.
6 Switch off all heavy electrical consumers: air conditioning, heaters, etc.
7 Transmission mode switch – Normal.
8 Select 2nd Gear; accelerate slowly. After 5 seconds, select 3rd Gear; accelerate slowly. After 5 seconds, select 4th Gear; accelerate slowly. After 5 seconds,
select Drive; cruise at 72 km/h (45 mph) for 30 seconds.
9 Stop vehicle.
10 Use the J Gate to shift through all gears while accelerating briskly to 87 km/h (55 mph). Cruise at this speed to allow torque converter lockup to occur in fifth gear.
11 Stop vehicle and repeat steps 8 through 10.
AAI Valve Air Assist Injection Valve IAT Sensor Intake Air Temperature Sensor
A/C Air conditioning IMT Valve Intake Manifold Tuning Valve
APP Sensor Accelerator Pedal Position Sensor IP Sensor Injection Pressure Sensor
B+ Battery Voltage KS 1 Knock Sensor – RH Bank
CHT Sensor Cylinder Head Temperature Sensor KS 2 Knock Sensor – LH Bank
CKP Sensor Crankshaft Position Sensor MAF Sensor Mass Air Flow Sensor
CMP Sensor 1 Camshaft Position Sensor – RH Bank PCM Powertrain Control Module
CMP Sensor 2 Camshaft Position Sensor – LH Bank PSP Switch Power Steering Pressure Switch
DLC Data Link Connector PTEC Powertrain Electronic Control
ECT Sensor Engine Coolant Temperature Sensor SCP Standard Corporate Protocol Network
EFT Sensor Engine Fuel Temperature Sensor TACM Throttle Actuator Control Module
EOT Sensor Engine Oil Temperature Sensor TCC Torque converter clutch
EVAP Canister Close Valve Evaporative Emission Canister Close Valve TFT Sensor Transmission Fluid Temperature Sensor
EVAP Canister Purge Valve Evaporative Emission Canister Purge Valve TP Sensor Throttle Position Sensor
FTP Sensor Fuel Tank Pressure Sensor VVT Valve 1 Variable Valve Timing Valve – RH Bank
HO2 Sensor 1 / 1 Heated Oxygen Sensor – RH Bank / Upstream VVT Valve 2 Variable Valve Timing Valve – LH Bank
HO2 Sensor 1 / 2 Heated Oxygen Sensor – RH Bank / Downstream
HO2 Sensor 2 / 1 Heated Oxygen Sensor – LH Bank / Upstream
HO2 Sensor 2 / 2 Heated Oxygen Sensor – LH Bank / Downstream
ACCF Air conditioning clutch output – fault detected EFPT Fuel injection pressure sensor (raw input)
ACCON A/C clutch commanded on EFPT1 Fuel injection pressure sensor before PCM default action
ACP Air conditioning high side pressure EFT Engine fuel temperature sensor (raw input)
ADCF Adaptive damping control output – fault detected EFT1 Engine fuel temperature sensor before PCM default action
AFT1F Adaptive fueling table 1 – failure EOTA Engine oil temperature -actual
AFT2F Adaptive fueling table 2 – failure EPCS1 Electronic pressure control solenoid 1
ASLIP Actual torque converter slip value EPCS2 Electronic pressure control solenoid 2
ATMR1 Time since engine start EPCS3 Electronic pressure control solenoid 3
CAM ANGLE1 Actual position of right camshaft EPCSF Electronic pressure control solenoid fault detected
CAMDC Variable valve timing right bank duty cycle FP1 Fuel pump – output fault detected
CAMERR Actual position of right camshaft FPDC Modulated fuel pump control – duty cycle
CANPF EVAP Canister purge output – fault detected FTPT Fuel tank pressure sensor
CANVF EVAP Canister close valve output – fault detected FUEL Fuel tank level
CCSF Coast clutch solenoid fault detected GEAR In gear
CHTC Cylinder head temperature before PCM default action GRCUR Current transmission gear ratio
CLOOP Closed loop fuel HO2S11 HO2S bank 1 upstream sensor voltage –
CLOOP1 Closed loop fuel with HO2S fault before correcting for %h(CSD) condition.
CLV Calculated load value HO2S12 HO2S bank 1 downstream sensor voltage –
before correcting for %h(CSD) condition.
CVSDC EVAP Canister close valve duty cycle
HO2S1D HO2S voltage – bank 1 downstream
DOLF Data link output – fault detected
ECT Engine coolant temperature – degrees Celsius
ECT2 Engine coolant temperature – degrees Fahrenheit
ECTF Engine coolant temperature sensor failure
EDF Low speed fan output – fault detected
HO2S1F Heated oxygen sensor 1 – failure LSFP Low speed fuel pump output – fault detected
HO2S1U HO2S voltage – bank 1 upstream MAFF Mass air flow sensor – failure
HO2S1UA HO2S bank 1 upstream heater current monitor MILF CHECK ENGINE MIL output fault detected
HO2S2D HO2S voltage – bank 2 downstream O212F HO2S bank 1 downstream – heater fault detected
HO2S2F Heated oxygen sensor 2 – failure OLOOP3 Open loop fuel – conditions not met; go to closed loop
HO2S2U HO2S voltage – bank 2 upstream OTRIP OBDII trip completed
HTR11 HO2S bank 1 upstream – heater On PNPS Park neutral position sensor
IAC1 Idle speed control- fault detected REVSW Reverse switch (not used – manual transmission)
IAC2 Idle speed control output – over current fault detected RPM2 Engine speed
IATF Intake air temperature sensor failure RPM2 Engine speed
IMCDC Intake manifold communications control – duty cycle RTT Transmission gear ratio
IMCF Inlet manifold communications output – fault indicated SAFTOT Spark advance
IMRCF Inlet manifold runner control output fault indicated SCACL Cruise control set/ acceleration switch
INDSA Park neutral position sensor SCAN Cruise control cancel switch
INJ1 Air assist injection fault SCN Cruise control null state
ISC1 Idle speed control – desired RPM SCOF Cruise control Off switch
KAMRF1 Adaptive fuel correction multiplier – bank 1 SCON Cruise control On switch
KAMRF2 Adaptive fuel correction multiplier – bank 2 SCRES Cruise control resume switch
LAMBSE1 Desired open loop equivalence ratio – bank 1 SCTAP Cruise control coast tap down switch
LAMBSE2 Desired open loop equivalence ratio – bank 2 SLIPA Absolute torque converter slip value (not used)
LOAD Air charge load normalized to sea level SLIPD Desired torque converter slip value (not used)
SSCM Shift solenoids – commanded gear TOTFM Transmission fluid temperature before PCM default action
SSDCM Shift solenoids commanded gear TOTLK Transmission over temperature lockup mode
SSDF Shift solenoid output fault TPS Throttle position
SSD1 Shift solenoid 1 TPSF Throttle position sensor failure
SSD1F Shift solenoid 1 output fault TRS1 Transmission range sensor 1
SSD2 Shift solenoid 2 TRS2 Transmission range sensor 2
SSD2F Shift solenoid 2 output fault TRS3 Transmission range sensor 3
SSD3 Shift solenoid 3 TRS4 Transmission range sensor 4
SSD3F Shift solenoid 3 output fault TSS Turbine speed sensor
TCCDC Torque converter clutch solenoid duty cycle VCT1F Variable valve timing bank 1 output – fault detected
TCCF Torque converter clutch solenoid duty cycle fault detected VCT2F Variable valve timing bank 2 output – fault detected
TCS Transmission control switch (D – 4 switch) VMVDC EVAP Canister purge valve duty cycle
TCTF Secondary throttle output – fault detected VMVM EVAP Canister purge valve output state monitor
TIS Transmission input speed (Turbine speed) VPWR Battery voltage
TMILF Transmission fault lamp output fault detected VSF Variable speed fan level
TOS Transmission output speed (OSS) VSS Vehicle speed sensor
TOT2 Actual transmission fluid temperature (TFT)
P0065 V8 EMS Air assisted fuel injection (AAI) control KOEO – page 3, or 2 N None AAI System piping:
OBD II range / performance Comprehensive component restricted, disconnected, broken
monitor engine management AAI Valve failure
drive cycle – page 7
P0066 V8 EMS Air assisted fuel injection (AAI) control KOEO – page 3, or 2 N None AAI Valve B+ power supply circuit fault
OBD II circuit malfunction KOER – page 3, or AAI Valve to PCM PWM drive circuit:
open circuit, high resistance, short circuit
Comprehensive component
monitor engine management AAI Valve failure
drive cycle – page 7
P0102 EMS MAF Sensor sense circuit low voltage KOER – page 3, or 2 N None Restricted air filter
OBD II Comprehensive component MAF Sensor to PCM sensing circuit:
monitor engine management high resistance, open circuit or intermittent
drive cycle – page 7 short circuit to ground
MAF Sensor supply circuit:
open circuit or short circuit to ground
MAF Sensor failure
P0103 EMS MAF Sensor sense circuit high voltage KOEO – page 3, or 2 N None MAF Sensor to PCM reference ground circuit:
OBD II KOER – page 3, or open circuit
MAF Sensor to PCM sensing circuit:
Comprehensive component short circuit to high voltage
monitor engine management
drive cycle – page 7 MAF Sensor failure
P0112 EMS IAT Sensor sense circuit high voltage KOEO – page 3, or 2 N PCM Default: IAT Sensor to PCM wiring:
OBD II (low temperature) KOER – page 3, or – IAT default value 38 °C open circuit or high resistance
(100 °F) IAT Sensor to PCM sensing circuit:
Comprehensive component short circuit to high voltage
monitor engine management
drive cycle – page 7 IAT Sensor failure
P0113 EMS IAT Sensor sense circuit low voltage KOEO – page 3, or 2 N PCM Default: IAT Sensor to PCM sensing circuit:
OBD II (high temperature) KOER – page 3, or – IAT default value 38 °C short circuit to ground
(100 °F) IAT Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0116 EMS ECT (V8) / CHT (V6) Sensor shift Comprehensive component N N None Low coolant level
JAG preventing OBD Monitor completion monitor engine management Contaminated coolant
drive cycle – page 7
Engine coolant thermostat failure
CHT Sensor to cylinder head poor contact – V6
ECT / CHT Sensor to PCM sensing circuit:
high resistance, open circuit or short circuit to
high voltage
ECT / CHT Sensor failure
P0117 V8 EMS ECT Sensor sense circuit low voltage KOEO – page 3, or 2 N PCM Default: ECT Sensor to PCM sensing circuit:
OBD II (high temperature) KOER – page 3, or – ECT default value 102 °C short circuit to ground
(215 °F) ECT Sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P0118 V8 EMS ECT Sensor sense circuit high voltage KOEO – page 3, or 2 N PCM Default: ECT Sensor to PCM wiring:
OBD II (low temperature) KOER – page 3, or – ECT default value 102 °C open circuit or high resistance
(215 °F) ECT Sensor to PCM sensing circuit:
Comprehensive component short circuit to high voltage
monitor engine management
drive cycle – page 7 ECT Sensor failure
P0122 EMS TP Sensor sense circuit low voltage – TP1 KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “1”
JAG KOER – page 3, or signals are received from (TP Sensor pin 10):
remaining sensors) open circuit or high resistance
Comprehensive component TP Sensor failure
monitor engine management
drive cycle – page 7
P0123 EMS TP Sensor sense circuit high voltage – TP1 KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “1”
JAG KOER – page 3, or signals are received from (TP Sensor pin 10):
remaining sensors) short circuit to high voltage
Comprehensive component TP Sensor failure
monitor engine management
drive cycle – page 7
P0124 EMS TP Sensor signal intermittent – TP1 KOEO – page 3, or N N None (as long as normal TP TP Sensor to PCM sensing circuit “1”
JAG KOER – page 3, or signals are received from (TP Sensor pin 10) intermittent:
remaining sensors) open circuit, high resistance, short circuit to
Comprehensive component ground or high voltage
monitor engine management TP Sensor failure
drive cycle – page 7
P0125 EMS ECT / CHT Sensor response insufficient for Comprehensive component 2 N None Low coolant level
OBD II closed loop fuel metering control monitor engine management Contaminated coolant
drive cycle – page 7
Engine coolant thermostat failure
(Coolant thermostat monitor) CHT Sensor to cylinder head poor contact – V6
ECT / CHT Sensor to PCM sensing circuit:
high resistance, open circuit or short circuit to
high voltage
Engine cooling fan stuck on high speed
Above normal air flow through engine
compartment due to accident damage and/or
missing panels
P0131 EMS HO2 Sensor sense circuit low voltage – Heated oxygen sensors 2 N None HO2 Sensor 1/1 disconnected
OBD II bank 1, upstream (1/1) monitor drive cycle – page 4 HO2 Sensor 1/1 to PCM sensing circuit:
open circuit
HO2 Sensor 1/1 short circuit to ground
HO2 Sensor 1/1 failure
P0132 EMS HO2 Sensor sense circuit high voltage – KOER – page 3, or 2 N None HO2 Sensor 1/1 to PCM sensing circuit:
OBD II bank 1, upstream (1/1) Heated oxygen sensors short circuit to high voltage
monitor drive cycle – page 4 HO2 Sensor 1/1 reference ground circuit
(HO2 sensor to splice): open circuit
HO2 Sensor 1/1 failure
P0133 EMS HO2 Sensor sense circuit slow response – Heated oxygen sensors 2 N None Engine misfire
OBD II bank 1, upstream (1/1) monitor drive cycle – page 4 HO2 Sensor 1/1 disconnected
HO2 Sensor 1/1 mechanical damage
HO2 Sensor 1/1 to PCM wiring:
intermittent open circuit
HO2 Sensor 1/1 to PCM sensing circuit:
short circuit to high voltage
HO2 Sensor 1/1 short circuit to ground
HO2 Sensor 1/1 reference ground circuit
(HO2 sensor to splice): open circuit
HO2 Sensor 1/1 heater circuit fault
Exhaust leak
Low exhaust temperature
Injector flow partially restricted
Catalyst efficiency decrease
HO2 Sensor 1/1 failure
P0135 EMS HO2 Sensor heater circuit malfunction – KOEO – page 3, or 2 N None HO2 Sensor 1/1 disconnected
OBD II bank 1, upstream (1/1) KOER – page 3, or HO2 Sensor 1/1 heater power supply:
open circuit
Heated oxygen sensors
monitor drive cycle – page 4 HO2 Sensor 1/1 heater to ECM wiring:
short circuit or open circuit
HO2 Sensor 1/1 heater failure
P0136 EMS HO2 Sensor sense circuit malfunction – Heated oxygen sensors 2 N None HO2 Sensor 1/2 to PCM sensing circuit:
OBD II bank 1, downstream (1/2) monitor drive cycle – page 4 open circuit, high resistance, short circuit to
ground or high voltage
HO2 Sensor 1/2 failure
P0138 EMS HO2 Sensor sense circuit high voltage – KOER – page 3, or 2 N None HO2 Sensor 1/2 to PCM sensing circuit:
OBD II bank 1, downstream (1/2) Heated oxygen sensors short circuit to high voltage
monitor drive cycle – page 4 HO2 Sensor 1/2 reference ground circuit
(HO2 sensor to splice): open circuit
HO2 Sensor 1/2 failure
P0141 EMS HO2 Sensor heater circuit malfunction – KOEO – page 3, or 2 N None HO2 Sensor 1/2 disconnected
OBD II bank 1, downstream (1/2) KOER – page 3, or HO2 Sensor 1/2 heater power supply:
open circuit
Heated oxygen sensors
monitor drive cycle – page 4 HO2 Sensor 1/2 heater to ECM wiring:
short circuit or open circuit
HO2 Sensor 1/2 heater failure
P0151 EMS HO2 Sensor sense circuit low voltage – Heated oxygen sensors 2 N None HO2 Sensor 2/1 disconnected
OBD II bank 2, upstream (2/1) monitor drive cycle – page 4 HO2 Sensor 2/1 to PCM sensing circuit:
open circuit
HO2 Sensor 2/1 short circuit to ground
HO2 Sensor 2/1 failure
P0152 EMS HO2 Sensor sense circuit high voltage – KOER – page 3, or 2 N None HO2 Sensor 2/1 to PCM sensing circuit:
OBD II bank 2, upstream (2/1) Heated oxygen sensors short circuit to high voltage
monitor drive cycle – page 4 HO2 Sensor 2/1 reference ground circuit
(HO2 sensor to splice): open circuit
HO2 Sensor 2/1 failure
P0153 EMS HO2 Sensor sense circuit slow response – Heated oxygen sensors 2 N None Engine misfire
OBD II bank 2, upstream (2/1) monitor drive cycle – page 4 HO2 Sensor 2/1 disconnected
HO2 Sensor 2/1 mechanical damage
HO2 Sensor 2/1 to PCM wiring:
intermittent open circuit
HO2 Sensor 2/1 to PCM sensing circuit:
short circuit to high voltage
HO2 Sensor 2/1 short circuit to ground
HO2 Sensor 2/1 reference ground circuit
(HO2 sensor to splice): open circuit
HO2 Sensor 2/1 heater circuit fault
Exhaust leak
Low exhaust temperature
Injector flow partially restricted
Catalyst efficiency decrease
HO2 Sensor 2/1 failure
P0155 EMS HO2 Sensor heater circuit malfunction – KOEO – page 3, or 2 N None HO2 Sensor 2/1 disconnected
OBD II bank 2, upstream (2/1) KOER – page 3, or HO2 Sensor 2/1 heater power supply:
open circuit
Heated oxygen sensors
monitor drive cycle – page 4 HO2 Sensor 2/1 heater to ECM wiring:
short circuit or open circuit
HO2 Sensor 2/1 heater failure
P0156 EMS HO2 Sensor sense circuit malfunction – Heated oxygen sensors 2 N None HO2 Sensor 2/2 to PCM sensing circuit:
OBD II bank 2, downstream (2/2) monitor drive cycle – page 4 open circuit, high resistance, short circuit to
ground or high voltage
HO2 Sensor 2/2 failure
P0158 EMS HO2 Sensor sense circuit high voltage – KOER – page 3, or 2 N None HO2 Sensor 2/2 to PCM sensing circuit:
OBD II bank 2, downstream (2/2) Heated oxygen sensors short circuit to high voltage
monitor drive cycle – page 4 HO2 Sensor 2/2 reference ground circuit
(HO2 sensor to splice): open circuit
HO2 Sensor 2/2 failure
P0161 EMS HO2 Sensor heater circuit malfunction – KOEO – page 3, or 2 N None HO2 Sensor 2/2 disconnected
OBD II bank 2, downstream (2/2) KOER – page 3, or HO2 Sensor 2/2 heater power supply:
open circuit
Heated oxygen sensors
monitor drive cycle – page 4 HO2 Sensor 2/2 heater to ECM wiring:
short circuit or open circuit
HO2 Sensor 2/2 heater failure
P0171 EMS System too lean – bank 1 Adaptive fuel monitor drive 2 N None Engine misfire
OBD II cycle – page 4 Air intake leak between MAF Sensor and throttle
Fuel filter, system restriction
Fuel injector restriction
Fuel pressure sensor failure (low fuel pressure)
Low fuel pump output
HO2 Sensor(s) (1/1, 1/2)
harness wiring condition fault
Exhaust leak (before catalyst)
PCM receiving incorrect signal from one or more
of the following components: ECT or CHT
Sensor, MAF Sensor, IAT Sensor, IP Sensor,
EFT Sensor, TP Sensor(s), TACM
P0172 EMS System too rich – bank 1 Adaptive fuel monitor drive 2 N None Restricted air filter
OBD II cycle – page 4 Leaking fuel injector(s)
Fuel pressure sensor failure (high fuel pressure)
PCM receiving incorrect signal from one or more
of the following components: ECT or CHT
Sensor, MAF Sensor, IAT Sensor, IP Sensor,
EFT Sensor, TP Sensor(s), TACM
P0174 EMS System too lean – bank 2 Adaptive fuel monitor drive 2 N None Engine misfire
OBD II cycle – page 4 Air intake leak between MAF Sensor and throttle
Fuel filter, system restriction
Fuel injector restriction
Fuel pressure sensor failure (low fuel pressure)
Low fuel pump output
HO2 Sensor(s) (2/1, 2/2)
harness wiring condition fault
Exhaust leak (before catalyst)
PCM receiving incorrect signal from one or more
of the following components: ECT or CHT
Sensor, MAF Sensor, IAT Sensor, IP Sensor,
EFT Sensor, TP Sensor(s), TACM
P0175 EMS System too rich – bank 2 Adaptive fuel monitor drive 2 N None Restricted air filter
OBD II cycle – page 4 Leaking fuel injector(s)
Fuel pressure sensor failure (high fuel pressure)
PCM receiving incorrect signal from one or more
of the following components: ECT or CHT
Sensor, MAF Sensor, IAT Sensor, IP Sensor,
EFT Sensor, TP Sensor(s), TACM
P0180 EMS EFT Sensor circuit malfunction KOEO – page 3, or 2 N None EFT Sensor disconnected
OBD II KOER – page 3, or EFT Sensor to PCM sensing circuit:
high resistance, open circuit, short circuit to
Comprehensive component ground or high voltage
monitor engine management
drive cycle – page 7 EFT Sensor failure
P0190 EMS IP Sensor circuit malfunction Comprehensive component 2 N None IP Sensor reference ground circuit (to splice):
OBD II monitor engine management open circuit
drive cycle – page 7 IP Sensor reference voltage circuit (to splice):
open circuit
IP Sensor to PCM sensing circuit:
open circuit, high resistance, short circuit to
ground or high voltage
IP Sensor failure
P0192 EMS IP Sensor sense circuit low voltage KOEO – page 3, or 2 N None IP Sensor reference voltage circuit (to splice):
OBD II (low pressure) KOER – page 3, or open circuit
IP Sensor to PCM sensing circuit:
Comprehensive component open circuit, high resistance, short circuit to
monitor engine management ground
drive cycle – page 7
IP Sensor failure
P0193 EMS IP Sensor sense circuit high voltage KOEO – page 3, or 2 N None IP Sensor reference ground circuit (to splice):
OBD II (high pressure) KOER – page 3, or open circuit
IP Sensor to PCM sensing circuit:
Comprehensive component short circuit to high voltage
monitor engine management
drive cycle – page 7 IP Sensor failure
P0196 EMS EOT Signal does not follow CHT / ECT Comprehensive component 2 N PCM Default: EOT Sensor to PCM sensing circuit:
OBD II signal monitor engine management – V6 CHT substituted high resistance when hot
drive cycle – page 7 EOT Sensor to PCM sensing circuit:
– V8 ECT substituted intermittent high resistance
EOT Sensor failure
P0201 EMS Fuel injector 1/1 circuit malfunction Comprehensive component N N None Injector disconnected
JAG monitor engine management Injector harness wiring: open or short circuit
drive cycle – page 7
Injector failure
P0202 EMS Fuel injector 1/2 circuit malfunction Comprehensive component N N None Injector disconnected
JAG monitor engine management Injector harness wiring: open or short circuit
drive cycle – page 7
Injector failure
P0203 EMS Fuel injector 1/3 circuit malfunction Comprehensive component N N None Injector disconnected
JAG monitor engine management Injector harness wiring: open or short circuit
drive cycle – page 7
Injector failure
P0204 EMS Fuel injector 1/4 circuit malfunction (V8) Comprehensive component N N None Injector disconnected
JAG Fuel injector 2/1 circuit malfunction (V6) monitor engine management Injector harness wiring: open or short circuit
drive cycle – page 7
Injector failure
P0205 EMS Fuel injector 2/1 circuit malfunction (V8) Comprehensive component N N None Injector disconnected
JAG Fuel injector 2/2 circuit malfunction (V6) monitor engine management Injector harness wiring: open or short circuit
drive cycle – page 7
Injector failure
P0206 EMS Fuel injector 2/2 circuit malfunction (V8) Comprehensive component N N None Injector disconnected
JAG Fuel injector 2/3 circuit malfunction (V6) monitor engine management Injector harness wiring: open or short circuit
drive cycle – page 7
Injector failure
P0207 V8 EMS Fuel injector 2/3 circuit malfunction Comprehensive component N N None Injector disconnected
JAG monitor engine management Injector harness wiring: open or short circuit
drive cycle – page 7
Injector failure
P0208 V8 EMS Fuel injector 2/4 circuit malfunction Comprehensive component N N None Injector disconnected
JAG monitor engine management Injector harness wiring: open or short circuit
drive cycle – page 7
Injector failure
P0222 EMS TP Sensor sense circuit low voltage – TP2 KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “2”
JAG KOER – page 3, or signals are received from (TP Sensor pin 1):
remaining sensors) open circuit or high resistance
Comprehensive component TP Sensor failure
monitor engine management
drive cycle – page 7
P0223 EMS TP Sensor sense circuit high voltage – TP2 KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “2”
JAG KOER – page 3, or signals are received from (TP Sensor pin 1):
remaining sensors) short circuit to high voltage
Comprehensive component TP Sensor failure
monitor engine management
drive cycle – page 7
P0224 EMS TP Sensor signal intermittent – TP2 KOEO – page 3, or N N None (as long as normal TP TP Sensor to PCM sensing circuit “2”
JAG KOER – page 3, or signals are received from (TP Sensor pin 1) intermittent:
remaining sensors) open circuit, high resistance, short circuit to
Comprehensive component ground or high voltage
monitor engine management TP Sensor failure
drive cycle – page 7
P0227 EMS TP Sensor sense circuit low voltage – TP3 KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “3”
JAG KOER – page 3, or signals are received from (TP Sensor pin 2):
remaining sensors) open circuit or high resistance
Comprehensive component TP Sensor failure
monitor engine management
drive cycle – page 7
P0228 EMS TP Sensor sense circuit high voltage – TP3 KOEO – page 3, or N A, M None (as long as normal TP TP Sensor to PCM sensing circuit “3”
JAG KOER – page 3, or signals are received from (TP Sensor pin 2):
remaining sensors) short circuit to high voltage
Comprehensive component TP Sensor failure
monitor engine management
drive cycle – page 7
P0229 EMS TP Sensor signal intermittent – TP3 KOEO – page 3, or N N None (as long as normal TP TP Sensor to PCM sensing circuit “3”
JAG KOER – page 3, or signals are received from (TP Sensor pin 2) intermittent:
remaining sensors) open circuit, high resistance, short circuit to
Comprehensive component ground or high voltage
monitor engine management TP Sensor failure
drive cycle – page 7
P0300 EMS Random misfire detected Misfire monitor drive cycle – 1 or 2 N None Cylinder compression low
OBD II page 4 ** Worn camshaft / broken valve spring(s)
Fuel delivery pressure (low / high)
Fuel injector(s) restricted / leaking
Fuel injector(s) continuously open
Fuel contamination
Fuel injector circuit fault(s)
(Injector DTCs also flagged)
Spark plug failure / fouled / incorrect gap
PCM to ignition coil primary circuit fault
(Cylinder misfire detected DTC also flagged)
Ignition coil failure
P0301 EMS Misfire detected – cylinder 1 (1/1) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0302 EMS Misfire detected – cylinder 2 (1/2) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0303 EMS Misfire detected – cylinder 3 (1/3) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0304 EMS Misfire detected – cylinder 4 Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II (1/4 V8, 2/1 V6) page 4 **
**If the misfire is severe enough to cause catalyst damage, the individual cylinder DTC will be flagged immediately and the CHECK ENGINE MIL will flash.
P0305 EMS Misfire detected – cylinder 5 Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II (2/1 V8, 2/2 V6) page 4 **
P0306 EMS Misfire detected – cylinder 6 Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II (2/2 V8, 2/3 V6) page 4 **
P0307 V8 EMS Misfire detected – cylinder 7 (2/3 V8) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0308 V8 EMS Misfire detected – cylinder 8 (2/4 V8) Misfire monitor drive cycle – 1 or 2 N None Refer to P0300 Possible Causes
OBD II page 4 **
P0320 EMS CKP Sensor circuit malfunction Comprehensive component 2 N None CKP Sensor disconnected
OBD II monitor engine management (The engine will shut off) CKP Sensor gap incorrect
drive cycle – page 7
CKP Sensor reluctor damaged teeth
Foreign matter on CKP Sensor face – V8
Foreign matter on CKP Sensor (on drive plate) –
V8
CKP Sensor sensing circuit:
open circuit, high resistance, short circuit to
ground or high voltage
CKP Sensor failure
P0325 EMS KS (knock sensor) circuit malfunction KOER – page 3, or 2 N None Poor sensor contact with the cylinder block
OBD II – bank 1 V8 Comprehensive component KS to PCM sensing circuit (KS pin 2):
– front (bank 2) V6 monitor engine management open circuit, high resistance, short circuit to
drive cycle – page 7 ground or high voltage
KS to PCM reference ground circuit
(KS pin 1): open circuit, high resistance, short
circuit to high voltage
KS failure
**If the misfire is severe enough to cause catalyst damage, the individual cylinder DTC will be flagged immediately and the CHECK ENGINE MIL will flash.
P0330 EMS KS (knock sensor) circuit malfunction KOER – page 3, or 2 N None Poor sensor contact with the cylinder block
OBD II – bank 2 V8 Comprehensive component KS to PCM sensing circuit (KS pin 2):
– rear (bank 1) V6 monitor engine management open circuit, high resistance, short circuit to
drive cycle – page 7 ground or high voltage
KS to PCM reference ground circuit
(KS pin 1): open circuit, high resistance, short
circuit to high voltage
KS failure
P0340 EMS CMP Sensor circuit malfunction – bank 1 Comprehensive component 2 N PCM Default: Bank 1 CMP Sensor disconnected
OBD II monitor engine management – VVT inhibited Bank 1 CMP Sensor gap incorrect / foreign
drive cycle – page 7 matter on sensor face
(Decreased engine
performance) Bank 1 CMP Sensor sensing circuit:
open circuit, short circuit to ground, short
circuit to high voltage
Bank 1 CMP Sensor reference ground circuit
(to splice): open circuit
Bank 1 CMP Sensor failure
P0341 EMS CMP Sensor circuit malfunction – bank 2 Comprehensive component 2 N PCM Default: Bank 2 CMP Sensor disconnected
OBD II monitor engine management – VVT inhibited Bank 2 CMP Sensor gap incorrect / foreign
drive cycle – page 7 matter on sensor face
(Decreased engine
performance) Bank 2 CMP Sensor sensing circuit:
open circuit, short circuit to ground, short
circuit to high voltage
Bank 2 CMP Sensor reference ground circuit
(to splice): open circuit
Bank 2 CMP Sensor failure
P0350 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Ignition coils power supply:
OBD II undetermined cylinder identification monitor engine management open circuit, short circuit
drive cycle – page 7 Ignition suppression capacitor(s) failure
Incorrect CKP Sensor air gap
P0351 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Ignition coil disconnected
OBD II cylinder 1/1 monitor engine management PCM to ignition coil primary circuit:
drive cycle – page 7 open circuit, high resistance, short circuit to
ground
Ignition coil failure
(If other individual ignition coil primary circuit
DTCs are flagged, refer to P0350 Possible
Causes)
P0352 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II cylinder 1/2 monitor engine management
drive cycle – page 7
P0353 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II cylinder 1/3 monitor engine management
drive cycle – page 7
P0354 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II V6 cylinder 2/1; V8 cylinder 1/4 monitor engine management
drive cycle – page 7
P0355 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II V6 cylinder 2/2; V8 cylinder 2/1 monitor engine management
drive cycle – page 7
P0356 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II V6 cylinder 2/3; V8 cylinder 2/2 monitor engine management
drive cycle – page 7
P0357 V8 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II V8 cylinder 2/3 monitor engine management
drive cycle – page 7
P0358 V8 EMS Ignition coil primary circuit malfunction – Comprehensive component 2 N None Refer to P0531 Possible Causes
OBD II V8 cylinder 2/4 monitor engine management
drive cycle – page 7
P0420 EMS Catalytic converter system efficiency Catalyst efficiency monitor 2 N None Bank 1 HO2 sensor(s) disconnected
OBD II below threshold – bank 1 drive cycle – page 5 Bank 1 HO2 sensor(s) to PCM wiring fault
Bank 1 HO2 sensor(s) heater to PCM wiring fault
Bank 1 HO2 sensor(s) heater failure
Bank 1 upstream HO2 sensor failure
Bank 1 downstream HO2 sensor failure
Bank 1 catalyst failure
P0430 EMS Catalytic converter system efficiency Catalyst efficiency monitor 2 N None Bank 2 HO2 sensor(s) disconnected
OBD II below threshold – bank 2 drive cycle – page 5 Bank 2 HO2 sensor(s) to PCM wiring fault
Bank 2 HO2 sensor(s) heater to PCM wiring fault
Bank 2 HO2 sensor(s) heater failure
Bank 2 upstream HO2 sensor failure
Bank 2 downstream HO2 sensor failure
Bank 2 catalyst failure
P0442 EMS EVAP Control system leak detected – Evaporative system monitor 2 N None Fuel cap seal defective
OBD II small leak (1 mm; 0.040 in.) drive cycle – page 6 EVAP system leak (canister damage, pipework
damage)
EVAP Canister purge valve to PCM drive circuit:
open circuit, short circuit, high resistance
EVAP Canister purge valve power supply circuit:
open circuit
EVAP Canister purge valve to engine purge pipe
damaged / restricted / leaking
EVAP Canister purge valve operating vacuum
hose leak / restriction
EVAP Canister purge failure
Fuel tank leak
P0443 EMS EVAP Canister purge valve circuit KOEO – page 3, or 2 N None EVAP Canister purge valve to PCM drive circuit:
OBD II malfunction KOER – page 3, or open circuit, short circuit, high resistance
EVAP Canister purge valve power supply circuit:
Evaporative system monitor open circuit
drive cycle – page 6
EVAP Canister purge valve failure
P0451 EMS FTP Sensor range / performance Evaporative system monitor 2 N None FTP Sensor disconnected
OBD II drive cycle – page 6 FTP Sensor to PCM sensing circuit:
open circuit, short circuit to ground, short
circuit to B+ voltage
FTP Sensor to PCM reference voltage circuit:
open circuit or short circuit to ground
FTP Sensor to PCM wiring (supply, sense,
reference ground): short circuit to each other
FTP Sensor failure
P0452 EMS FTP Sensor circuit low voltage KOEO – page 3, or 2 N None FTP Sensor disconnected
OBD II (low pressure) KOER – page 3, or FTP Sensor to PCM sensing circuit:
open circuit or short circuit to ground
Evaporative system monitor
drive cycle – page 6 FTP Sensor to PCM reference voltage circuit:
open circuit or short circuit to ground
FTP Sensor failure
P0453 EMS FTP Sensor circuit high voltage KOEO – page 3, or 2 N None FTP Sensor to PCM wiring (supply, sense,
OBD II (high pressure) KOER – page 3, or reference ground): short circuit to each other
FTP Sensor to PCM sense circuit:
Evaporative system monitor short circuit to high voltage
drive cycle – page 6
FTP Sensor to PCM reference ground circuit:
open circuit
FTP Sensor failure
P0455 EMS EVAP Control system control – Evaporative system monitor 2 N None Fuel cap off
OBD II leak detected: major leak drive cycle – page 6 Fuel cap seal defective
Fuel tank over filled
EVAP system leak (canister damage, pipework
damage)
EVAP Canister purge valve to PCM drive circuit:
open circuit, short circuit, high resistance
EVAP Canister purge valve power supply circuit:
open circuit
EVAP Canister purge valve to engine purge pipe
damaged / restricted / leaking
EVAP Canister purge valve operating vacuum
hose leak / restriction
EVAP Canister purge failure
FTP Sensor not responding to pressure changes
(restricted / failure)
Fuel tank leak
P0456 EMS EVAP Control system control – Evaporative system monitor 2 N None Fuel cap seal defective
OBD II leak detected: very small leak (0.5 mm; drive cycle – page 6 EVAP system leak (canister damage, pipework
0.020 in.) damage)
EVAP Canister purge valve to PCM drive circuit:
open circuit, short circuit, high resistance
EVAP Canister purge valve power supply circuit:
open circuit
EVAP Canister purge valve to engine purge pipe
damaged / restricted / leaking
EVAP Canister purge valve operating vacuum
hose leak / restriction
EVAP Canister purge failure
Fuel tank leak
P0460 EMS Fuel level sensor(s) circuit malfunction KOEO – page 3, or N N None Fuel level sensor(s) to RECM sense circuits:
JAG KOER – page 3, or open circuit, high resistance, short circuit
RECM / PCM SCP communication fault
Evaporative system monitor (U Code flagged)
drive cycle – page 6
Fuel level sensor(s) failure
P0500 ABS/TC Vehicle speed circuit malfunction Engine running; vehicle in N N None Rear wheel speed sensor(s) circuit(s):
JAG motion open circuit, high resistance, short circuit
Rear wheel speed sensor(s) failure
Front wheel speed sensor(s) circuit(s):
open circuit, high resistance, short circuit
Front wheel speed sensor(s) failure
Instrument pack malfunction
SCP Failure (code U1039 flagged)
P0503 TRANS Vehicle speed circuit – electrical noise Engine running; vehicle in N N None Wheel speed sensor(s) circuit(s) electrical noise
JAG motion Instrument pack malfunction
SCP Failure (code U1039 flagged)
P0505 EMS Idle air control malfunction KOER – page 3, or N N None Engine air filter restricted / defective
JAG Comprehensive component Engine air intake restricted / damaged
monitor engine management PCM / TACM circuit fault
drive cycle – page 7
TACM failure
Throttle failure
P0602 PCM PCM Programming error KOEO – page 3, or N N None PCM failure
JAG KOER – page 3, or
Comprehensive component
monitor engine management
drive cycle – page 7
P0603 PCM PCM Keep alive memory (KAM) test error KOEO – page 3 N N None PCM failure
JAG
P0605 PCM PCM Read only memory (ROM) test error KOEO – page 3 N N None PCM failure
JAG
P0703 EMS Brake ON / OFF switch circuit malfunction KOER – page 3, or N M, S PCM Default: Brake switch to PCM signal circuit:
JAG Engine running; operate – Speed control inhibited open circuit, high resistance, short circuit
brake pedal Brake switch power supply circuit:
open circuit, short circuit
Brake switch signal circuit (gearshift interlock,
ABS/TC, stop lamps): open circuit, short circuit
Brake switch failure
P0705 TRANS Range sensor circuit malfunction KOEO – page 3, or 2 A, M PCM Defaults to DRIVE (to Range sensor incorrect alignment
OBD II (sensor transmitting an invalid code) KOER – page 3, or maintain all five gears) Gear selector cable incorrectly adjusted
Comprehensive component J Gate gear selected Range sensor circuit:
monitor transmission drive illumination extinguished intermittent open circuit; open circuit
cycle – page 8 (Harsh shifts) Range sensor failure
P0708 TRANS Range sensor circuit open circuit KOEO – page 3, or 2 A, M PCM Defaults to DRIVE (to Range sensor circuit open circuit
OBD II KOER – page 3, or maintain all five gears) Range sensor disconnected
Comprehensive component J Gate gear selected Range sensor failure
monitor transmission drive illumination extinguished
cycle – page 8 (Harsh shifts)
P0712 TRANS TFT Sensor sense circuit low voltage KOEO – page 3, or N A, M, T PCM Default: TFT Sensor sense circuit short circuit to ground
JAG (high fluid temperature) KOER – page 3, or – TFT calculated from TFT Sensor failure
Comprehensive component ECT (V8) / CHT (V6)
monitor transmission drive ABS/TCCM, DSCCM
cycle – page 8 Default:
– traction control inhibited
(Firm shifts)
P0713 TRANS TFT Sensor sense circuit high voltage KOEO – page 3, or N A, M, T PCM Default: TFT Sensor sense circuit:
JAG (low fluid temperature) KOER – page 3, or – TFT calculated from open circuit, high resistance, short circuit to
high voltage
Comprehensive component ECT (V8) / CHT (V6)
TFT Sensor failure
monitor transmission drive ABS/TCCM, DSCCM
cycle – page 8 Default:
– traction control inhibited
(Firm shifts)
P0715 TRANS Turbine speed sensor circuit malfunction KOER – page 3, or 2 A, M PCM Default: Turbine speed sensor circuit:
OBD II Comprehensive component – Speed calculated from short circuit, high resistance, open circuit
monitor transmission drive output speed sensor Turbine speed sensor failure
cycle – page 8 (Harsh TCC shifts)
P0717 TRANS Turbine speed sensor sense circuit – KOER – page 3, or N A, M PCM Default: Turbine speed sensor sense circuit:
JAG no signal Comprehensive component – Speed calculated from open circuit
monitor transmission drive output speed sensor Turbine speed sensor failure
cycle – page 8 (Harsh TCC shifts)
P0718 TRANS Turbine speed sensor sense circuit – Comprehensive component N A, M PCM Default: Turbine speed sensor sense circuit:
JAG electrical noise monitor transmission drive – Speed calculated from short circuit, open circuit
cycle – page 8 output speed sensor
(Harsh TCC shifts)
P0720 TRANS Output speed sensor circuit malfunction Comprehensive component 2 A, M PCM Default: Output speed sensor circuit:
OBD II monitor transmission drive – Speed calculated from short circuit, high resistance, open circuit
cycle – page 8 SCP vehicle speed Output speed sensor failure
message
P0721 TRANS Output speed sensor sense circuit – Comprehensive component N A, M, T PCM Default: Output speed sensor sense circuit:
JAG electrical noise monitor transmission drive – Speed calculated from short circuit, open circuit
cycle – page 8 SCP vehicle speed
message
ABS/TCCM, DSCCM
Default:
– traction control inhibited
(Abnormal shift schedule)
P0722 TRANS Output speed sensor sense circuit – Comprehensive component N A, M, T PCM Default: Output speed sensor sense circuit intermittent:
JAG intermittent signal monitor transmission drive – Speed calculated from short circuit, high resistance, open circuit
cycle – page 8 SCP vehicle speed Output speed sensor failure
message
ABS/TCCM, DSCCM
Default:
– traction control inhibited
(Abnormal shift schedule)
P0731 TRANS 1st Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault
JAG monitor transmission drive – 1st Gear inhibited (shift solenoid DTC(s) also flagged)
cycle – page 8 Pressure control solenoid circuit fault
ABS/TCCM, DSCCM (pressure solenoid DTC(s) also flagged)
Default:
Engine speed signal malfunction
– traction control inhibited (CKP Sensor DTC(s) also flagged)
Transmission mechanical failure
P0732 TRANS 2nd Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault
JAG monitor transmission drive – 2nd Gear inhibited (shift solenoid DTC(s) also flagged)
cycle – page 8 Pressure control solenoid circuit fault
ABS/TCCM, DSCCM (pressure solenoid DTC(s) also flagged)
Default:
Engine speed signal malfunction
– traction control inhibited (CKP Sensor DTC(s) also flagged)
Transmission mechanical failure
P0733 TRANS 3rd Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault
JAG monitor transmission drive – 3rd Gear inhibited (shift solenoid DTC(s) also flagged)
cycle – page 8 Pressure control solenoid circuit fault
ABS/TCCM, DSCCM (pressure solenoid DTC(s) also flagged)
Default:
Engine speed signal malfunction
– traction control inhibited (CKP Sensor DTC(s) also flagged)
Transmission mechanical failure
P0734 TRANS 4th Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault
JAG monitor transmission drive – 4th Gear inhibited (shift solenoid DTC(s) also flagged)
cycle – page 8 Pressure control solenoid circuit fault
ABS/TCCM, DSCCM (pressure solenoid DTC(s) also flagged)
Default:
Engine speed signal malfunction
– traction control inhibited (CKP Sensor DTC(s) also flagged)
Transmission mechanical failure
P0735 TRANS 5th Gear ratio error Comprehensive component N A, M, T PCM Default: Shift solenoid circuit fault
JAG monitor transmission drive – 5th Gear inhibited (shift solenoid DTC(s) also flagged)
cycle – page 8 Pressure control solenoid circuit fault
ABS/TCCM, DSCCM (pressure solenoid DTC(s) also flagged)
Default:
Engine speed signal malfunction
– traction control inhibited (CKP Sensor DTC(s) also flagged)
Transmission mechanical failure
P0741 TRANS TCC Slip detected Comprehensive component N A, M, T Transmission will continue to TCC solenoid circuit fault
JAG monitor transmission drive attempt lock-up (TCC solenoid DTC(s) also flagged)
cycle – page 8 ABS/TCCM, DSCCM Pressure control solenoid circuit fault
Default: (pressure solenoid DTC(s) also flagged)
– traction control inhibited Transmission mechanical failure
P0743 TRANS TCC Solenoid circuit malfunction KOEO – page 3, or 2 A, M PCM Default: TCC Drive circuit:
OBD II KOER – page 3, or – TCC Lock-up inhibited open circuit; high resistance, short circuit to
ground
Comprehensive component TCC solenoid failure
monitor transmission drive
cycle – page 8
P0745 TRANS Pressure control solenoid 1 stuck Comprehensive component 2 A, M PCM Default: Pressure control solenoid 1drive circuit:
OBD II monitor transmission drive – 1st, 2nd, 4th, 5th shift short circuit to ground; open circuit
cycle – page 8 pattern Pressure control solenoid 1 failure
P0750 TRANS Shift solenoid 1 circuit malfunction KOEO – page 3, or 2 A, M PCM Default: Shift solenoid 1 drive circuit:
OBD II KOER – page 3, or – If short circuit to B+ V or short circuit to ground or B+ V; high resistance,
open circuit
Comprehensive component open circuit – 3rd, 2nd, 3rd,
4th, 5th shift pattern Shift solenoid 1 failure
monitor transmission drive
cycle – page 8 – If short circuit to ground –
1st, 2nd, 3rd shift pattern
(Harsh shifts)
P0755 TRANS Shift solenoid 2 circuit malfunction KOEO – page 3, or 2 A, M PCM Default: Shift solenoid 2 drive circuit:
OBD II KOER – page 3, or – If short circuit to B+ V or short circuit to ground or B+ V; high resistance,
open circuit
Comprehensive component open circuit – 1st, 2nd, 4th,
5th shift pattern Shift solenoid 2 failure
monitor transmission drive
cycle – page 8 – If short circuit to ground –
3rd, 2nd, 3rd, 4th, 5th shift
pattern
(Harsh shifts)
P0760 TRANS Shift solenoid 3 circuit malfunction KOEO – page 3, or 2 A, M PCM Default: Shift solenoid 3 drive circuit:
OBD II KOER – page 3, or – If short circuit to B+ V or short circuit to ground or B+ V; high resistance,
open circuit
Comprehensive component open circuit – 1st, 3rd, 4th,
5th shift pattern Shift solenoid 3 failure
monitor transmission drive
cycle – page 8 – If short circuit to ground –
normal shift pattern
(Harsh shifts)
P0765 TRANS Shift solenoid 4 circuit malfunction KOEO – page 3, or N A, M PCM Default: Shift solenoid 4 drive circuit:
JAG KOER – page 3, or – DRIVE – normal shift short circuit to ground or B+ V, high resistance,
open circuit
Comprehensive component pattern
Shift solenoid 4 failure
monitor transmission drive – Manual – 2, 3, 4 inhibited
cycle – page 8 (Harsh shifts)
P0775 TRANS Pressure control solenoid 2 stuck Comprehensive component 2 A, M PCM Default: Pressure control solenoid 2drive circuit:
OBD II monitor transmission drive – 1st, 1st, 3rd, 4th, 4th shift short circuit to ground; open circuit
cycle – page 8 pattern Pressure control solenoid 2 failure
P0779 TRANS Pressure control solenoid 2 drive circuit – KOEO – page 3, or N A, M PCM Default: Pressure control solenoid 2drive circuit:
JAG intermittent low voltage KOER – page 3, or – 1st, 1st, 3rd, 4th, 4th shift intermittent short circuit to ground
Comprehensive component pattern
monitor transmission drive
cycle – page 8
P0791 TRANS Intermediate speed sensor circuit Comprehensive component N A, M, T PCM Default: Intermediate speed sensor circuit:
JAG monitor transmission drive – One-way clutch test short circuit, high resistance, open circuit
cycle – page 8 inhibited Intermediate speed sensor failure
ABS/TCCM, DSCCM
Default:
– traction control inhibited
(Harsh shifts)
P0794 TRANS Intermediate speed sensor sense circuit – Comprehensive component N A, M PCM Default: Intermediate speed sensor sense circuit
JAG intermittent signal monitor transmission drive – One-way clutch test intermittent:
cycle – page 8 short circuit, high resistance, open circuit
inhibited
Intermediate speed sensor failure
(Harsh shifts)
P0795 TRANS Pressure control solenoid 3 stuck Comprehensive component 2 A, M PCM Default: Pressure control solenoid 3drive circuit:
OBD II monitor transmission drive – 1st, 2nd, 3rd gears only short circuit to ground, open circuit
cycle – page 8 Pressure control solenoid 3 failure
P0796 TRANS Pressure control solenoid 3 circuit – KOEO – page 3, or N A, M, T ABS/TCCM, DSCCM Pressure control solenoid 3 drive circuit:
JAG high voltage KOER – page 3, or Default: short circuit to B+ V
– traction control inhibited Pressure control solenoid 3 failure
Comprehensive component
monitor transmission drive (Harsh shifts) Transmission mechanical failure
cycle – page 8 (other DTCs logged)
P0797 TRANS Pressure control solenoid 3 circuit – KOEO – page 3, or 2 A, M PCM Default: Pressure control solenoid 3 drive circuit:
OBD II low voltage KOER – page 3, or – 1st, 2nd, 3rd gears only short circuit to ground
Pressure control solenoid 3 failure
Comprehensive component (Harsh shifts)
monitor transmission drive Transmission mechanical failure
cycle – page 8 (other DTCs logged)
P0799 TRANS Pressure control solenoid 3 drive circuit – KOEO – page 3, or N A, M PCM Default: Pressure control solenoid 3 drive circuit:
JAG intermittent low voltage KOER – page 3, or – 1st, 2nd, 3rd gears only intermittent short circuit to ground
Comprehensive component
monitor transmission drive
cycle – page 8
P0814 TRANS J Gate illumination circuit failure – Comprehensive component N N None PCM / J Gate illumination circuit(s):
JAG gear selected monitor transmission drive short circuit, open circuit
cycle – page 8 (PCM pins FH1-7, 8, 9)
P0840 TRANS Transmission pressure switch circuit KOEO – page 3, or N A, M PCM Default: Pressure switch to PCM signal circuit:
JAG malfunction KOER – page 3, or – Manual 2nd, 3rd inhibited short circuit, high resistance, open circuit
Pressure switch transmission internal circuit:
Comprehensive component short circuit, high resistance, open circuit
monitor transmission drive
cycle – page 8 Pressure switch failure
P1000 PCM OBD System checks not complete since KOEO – page 3, or N N None Refer to page 3
JAG last memory clear KOER – page 3, or
Drive vehicle
P1001 PCM KOER not complete KOER – page 3 N N None Refer to page 3
JAG
P1100 EMS MAF Sensor signal intermittent Comprehensive component N N None MAF Sensor to PCM sensing circuit intermittent:
JAG monitor engine management open circuit, high resistance, short circuit
drive cycle – page 7 MAF Sensor supply circuit intermittent:
open circuit or short circuit
MAF Sensor failure
P1101 EMS MAF Sensor out of self test range KOEO – page 3, or N N None MAF Sensor to PCM sensing circuit:
JAG KOER – page 3 open circuit, high resistance, short circuit
MAF Sensor supply circuit:
open circuit or short circuit
MAF Sensor failure
P1112 EMS IAT Sensor signal intermittent Comprehensive component N N PCM Default: IAT Sensor to PCM sensing circuit intermittent:
JAG monitor engine management – IAT default value 38 °C open circuit, high resistance, short circuit
drive cycle – page 7 (100 °F) IAT Sensor reference ground circuit (to splice):
intermittent open circuit
IAT Sensor failure
P1116 V8 EMS ECT Sensor out of self test range KOEO – page 3, or N N PCM Default: IAT Sensor to PCM sensing circuit:
JAG KOER – page 3 – ECT default value 102 °C open circuit, high resistance, short circuit
(215 °F) IAT Sensor reference ground circuit (to splice):
open circuit
IAT Sensor failure
P1117 EMS ECT / CHT Sensor signal intermittent Comprehensive component N N PCM Default: ECT / CHT Sensor to PCM sensing circuit
JAG monitor engine management – ECT / CHT default value intermittent:
drive cycle – page 7 open circuit, high resistance, short circuit
102 °C (215 °F)
ECT / CHT Sensor reference ground circuit
(to splice): intermittent open circuit
ECT / CHT Sensor failure
P1121 EMS TP Sensor signals inconsistent with MAF Comprehensive component 2 N None (as long as normal TP TP Sensors to PCM wiring harness fault
OBD II Sensor signals monitor engine management signals are received) MAF Sensor to PCM wiring harness fault
drive cycle – page 7
TP Sensor(s) failure
MAF Sensor failure
P1122 EMS APP Sensor circuit low voltage – APP1 KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “1”
JAG KOER – page 3, or signals are received from (sensor pin 5:
remaining sensors) open circuit or high resistance
Comprehensive component APP Sensor reference voltage (sensor pin 10):
monitor engine management open circuit
drive cycle – page 7
APP Sensor failure
P1123 EMS APP Sensor circuit high voltage – APP1 KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “1”
JAG KOER – page 3, or signals are received from (sensor pin 5):
remaining sensors) short circuit to high voltage
Comprehensive component APP Sensor reference ground (sensor pin 9):
monitor engine management open circuit
drive cycle – page 7
APP Sensor failure
P1124 EMS TP Sensor out of self test range KOEO – page 3, or N N None (as long as normal TP Accelerator pedal depressed during self test
JAG KOER – page 3, or signals are received) One or more individual TP Sensors to PCM
sensing circuits: open circuit, high resistance,
short circuit to ground or high voltage
TP Sensor failure
P1125 EMS TP Sensor signal intermittent Comprehensive component N N None One or more individual TP Sensors to PCM
JAG monitor engine management sensing circuits: open circuit, high resistance,
drive cycle – page 7 short circuit to ground or high voltage
TP Sensor failure
P1127 EMS Exhaust not warm enough; KOER – page 3, or N N None Engine not at normal operating temperature
JAG downstream HO2 Sensors not tested Heated oxygen sensors Exhaust system leak / failure
monitor drive cycle – page 4
P1128 EMS Upstream HO2 Sensors swapped from KOER – page 3, or N N None Upstream HO2 Sensors swapped from
JAG bank to bank Heated oxygen sensors bank to bank
monitor drive cycle – page 4 Upstream HO2 Sensors to PCM wiring fault
P1129 EMS Downstream HO2 Sensors swapped from KOER – page 3, or N N None Downstream HO2 Sensors swapped from
JAG bank to bank Heated oxygen sensors bank to bank
monitor drive cycle – page 4 Downstream HO2 Sensors to PCM wiring fault
P1130 EMS Lack of HO2 Sensor swing, adaptive fuel Heated oxygen sensors 2 N None HO2 Sensor 1/1 disconnected
OBD II at limit – bank 1, upstream (1/1) monitor drive cycle – page 4 HO2 Sensor 1/1 to PCM wiring fault
Engine induction air leak between MAF Sensor
and throttle
Exhaust system leak
Contaminated fuel
Fuel in engine oil
Engine misfire
HO2 Sensor 1/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1131 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or 2 N None HO2 Sensor 1/1 to PCM wiring fault
OBD II indicates lean – bank 1, upstream (1/1) Heated oxygen sensors Engine induction air leak between MAF Sensor
monitor drive cycle – page 4 and throttle
Exhaust system leak
HO2 Sensor 1/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1132 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or 2 N None HO2 Sensor 1/1 to PCM wiring fault
OBD II indicates rich – bank 1, upstream (1/1) Heated oxygen sensors Exhaust system restriction
monitor drive cycle – page 4 Contaminated fuel
Fuel in engine oil
HO2 Sensor 1/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1133 EMS Bank 1 fuel metering control shifted lean Comprehensive component 2 N None Temporary contamination of HO2 Sensor 1/1
OBD II monitor engine management causing “lean drift”
drive cycle – page 7 Temporary contamination of HO2 Sensor 1/2
causing “rich drift”
Engine misfire
HO2 Sensors 1/1 and 1/2 to PCM wiring fault(s)
Engine induction air leak between MAF Sensor
and throttle
Exhaust system leak
Water in bank 1 spark plug well(s)
HO2 Sensors 1/1 and/or 1/2 failure
P1134 EMS Bank 1 fuel metering control shifted rich Comprehensive component 2 N None Temporary contamination of HO2 Sensor 1/1
OBD II monitor engine management causing “rich drift”
drive cycle – page 7 Temporary contamination of HO2 Sensor 1/2
causing “lean drift”
Engine misfire
HO2 Sensors 1/1 and 1/2 to PCM wiring fault(s)
Exhaust system restriction
Water in bank 1 spark plug well(s)
HO2 Sensors 1/1 and/or 1/2 failure
P1135 EMS APP Sensor signal intermittent – APP1 KOEO – page 3, or N N None (as long as normal APP APP Sensor to PCM sensing circuit “1”
JAG KOER – page 3, or signals are received from (sensor pin 5):
remaining sensors) intermittent: open circuit, high resistance,
Comprehensive component short circuit
monitor engine management APP Sensor reference voltage (sensor pin 10):
drive cycle – page 7 intermittent open circuit
APP Sensor reference ground (sensor pin 9):
intermittent open circuit
APP Sensor failure
P1137 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or N N None HO2 Sensor 1/2 to PCM wiring fault
JAG indicates lean – bank 1, downstream (1/2) Heated oxygen sensors HO2 Sensor 1/2 failure
monitor drive cycle – page 4
P1138 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or N N None HO2 Sensor 1/2 to PCM wiring fault
JAG indicates rich – bank 1, downstream (1/2) Heated oxygen sensors HO2 Sensor 1/2 failure
monitor drive cycle – page 4
P1150 EMS Lack of HO2 Sensor swing, adaptive fuel Heated oxygen sensors 2 N None HO2 Sensor 2/1 disconnected
OBD II at limit – bank 2, upstream (2/1) monitor drive cycle – page 4 HO2 Sensor 2/1 to PCM wiring fault
Engine induction air leak between MAF Sensor
and throttle
Exhaust system leak
Contaminated fuel
Fuel in engine oil
Engine misfire
HO2 Sensor 1/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1151 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or 2 N None HO2 Sensor 2/1 to PCM wiring fault
OBD II indicates lean – bank 2, upstream (2/1) Heated oxygen sensors Engine induction air leak between MAF Sensor
monitor drive cycle – page 4 and throttle
Exhaust system leak
HO2 Sensor 2/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1152 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or 2 N None HO2 Sensor 2/1 to PCM wiring fault
OBD II indicates rich – bank 2, upstream (2/1) Heated oxygen sensors Exhaust system restriction
monitor drive cycle – page 4 Contaminated fuel
Fuel in engine oil
HO2 Sensor 2/1 failure
Fuel injection fault
PCM Keep alive memory (KAM) error
P1153 EMS Bank 2 fuel metering control shifted lean Comprehensive component 2 N None Temporary contamination of HO2 Sensor 2/1
OBD II monitor engine management causing “lean drift”
drive cycle – page 7 Temporary contamination of HO2 Sensor 2/2
causing “rich drift”
Engine misfire
HO2 Sensors 2/1 and 2/2 to PCM wiring fault(s)
Engine induction air leak between MAF Sensor
and throttle
Exhaust system leak
Water in bank 2 spark plug well(s)
HO2 Sensors 2/1 and/or 2/2 failure
P1154 EMS Bank 2 fuel metering control shifted rich Comprehensive component 2 N None Temporary contamination of HO2 Sensor 2/1
OBD II monitor engine management causing “rich drift”
drive cycle – page 7 Temporary contamination of HO2 Sensor 2/2
causing “lean drift”
Engine misfire
HO2 Sensors 2/1 and 2/2 to PCM wiring fault(s)
Exhaust system restriction
Water in bank 2 spark plug well(s)
HO2 Sensors 2/1 and/or 2/2 failure
P1157 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or N N None HO2 Sensor 2/2 to PCM wiring fault
JAG indicates lean – bank 2, downstream (2/2) Heated oxygen sensors HO2 Sensor 2/2 failure
monitor drive cycle – page 4
P1158 EMS Lack of HO2 Sensor swing, sensor KOER – page 3, or N N None HO2 Sensor 2/2 to PCM wiring fault
JAG indicates rich – bank 2, downstream (2/2) Heated oxygen sensors HO2 Sensor 2/2 failure
monitor drive cycle – page 4
P1183 EMS EOT Sensor circuit malfunction Comprehensive component 2 N PCM Default: EOT Sensor to PCM sensing circuit:
OBD II monitor engine management – V6 CHT substituted open circuit, high resistance, short circuit
drive cycle – page 7 EOT Sensor reference ground circuit (to splice):
– V8 ECT substituted open circuit
EOT Sensor failure
P1184 EMS EOT Sensor out of self test range KOEO – page 3, or N N PCM Default: EOT Sensor to PCM sensing circuit:
JAG KOER – page 3, or – V6 CHT substituted high resistance when hot
EOT Sensor to PCM sensing circuit:
Comprehensive component – V8 ECT substituted intermittent high resistance
monitor engine management
drive cycle – page 7 EOT Sensor failure
P1214 EMS APP Sensor signal intermittent – APP2 KOEO – page 3, or N N None (as long as normal APP APP Sensor to PCM sensing circuit “2”
JAG KOER – page 3, or signals are received from (sensor pin 4) intermittent:
remaining sensors) open circuit, high resistance, short circuit
Comprehensive component APP Sensor reference voltage (sensor pin 8):
monitor engine management intermittent open circuit
drive cycle – page 7
APP Sensor reference ground (sensor pin 6):
intermittent open circuit
APP Sensor failure
P1215 EMS APP Sensor circuit low voltage – APP3 KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “3”
JAG KOER – page 3, or signals are received from (sensor pin 7): open circuit or high resistance
remaining sensors) APP Sensor reference voltage (sensor pin 3):
Comprehensive component open circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1216 EMS APP Sensor circuit high voltage – APP3 KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “1”
JAG KOER – page 3, or signals are received from (sensor pin 7): short circuit to high voltage
remaining sensors) APP Sensor reference ground (sensor pin 2)
Comprehensive component open circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1217 EMS APP Sensor signal intermittent – APP3 KOEO – page 3, or N N None (as long as normal APP APP Sensor to PCM sensing circuit “3”
JAG KOER – page 3, or signals are received from (sensor pin 7) intermittent:
remaining sensors) open circuit, high resistance, short circuit
Comprehensive component APP Sensor reference voltage (sensor pin 3):
monitor engine management intermittent open circuit
drive cycle – page 7
APP Sensor reference ground (sensor pin 2):
intermittent open circuit
APP Sensor failure
P1222 EMS APP Sensor circuit low voltage – APP2 KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “2”
JAG KOER – page 3, or signals are received from (sensor pin 4): open circuit or high resistance
remaining sensors) APP Sensor reference voltage (sensor pin 8):
Comprehensive component open circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1223 EMS APP Sensor circuit high voltage – APP2 KOEO – page 3, or N A, M None (as long as normal APP APP Sensor to PCM sensing circuit “2”
JAG KOER – page 3, or signals are received from (sensor pin 4): short circuit to high voltage
remaining sensors) APP Sensor reference ground (sensor pin 6):
Comprehensive component open circuit
monitor engine management
drive cycle – page 7 APP Sensor failure
P1233 EMS Fuel delivery system disabled or KOEO – page 3, or N N None PCM to RECM fuel pump drive signal circuit
JAG inoperative KOER – page 3, or (Engine shut off) (PCM pin FH1-58):
open circuit, high resistance, short circuit
Comprehensive component RECM to fuel pump drive circuit:
monitor engine management open circuit, high resistance, short circuit
drive cycle – page 7
Fuel pump relay power supply:
open circuit, short circuit
Fuel pump relay to RECM power supply circuit:
open circuit
Fuel pump relay failure
P1235 EMS Fuel pump control out of range KOER – page 3, or N N None PCM to RECM fuel pump drive signal circuit
JAG Comprehensive component (Engine running too rich / (PCM pin FH1-58) intermittent:
open circuit, high resistance, short circuit
monitor engine management lean)
drive cycle – page 7 RECM to fuel pump drive circuit intermittent:
open circuit, high resistance, short circuit
P1237 EMS Fuel pump secondary circuit malfunction KOER – page 3, or N N None RECM to fuel pump drive circuit:
JAG Comprehensive component (Engine shut off) open circuit, high resistance, short circuit
monitor engine management Fuel pump relay power supply:
drive cycle – page 7 open circuit, short circuit
Fuel pump relay to RECM power supply circuit:
open circuit
Fuel pump relay failure
P1246 EMS Generator load input to PCM failure KOER – page 3 N M, C None Accessory drive belt failure
JAG PCM to generator load circuit (PCM pin PI1-50):
open circuit, high resistance, short circuit
Generator failure
P1260 EMS Vehicle theft detected – engine disabled KOEO – page 3 N N None Invalid ignition key code
JAG (PCM SCP input from PATS, INST, GECM) Passive anti-theft system (PATS) signal to
instrument pack missing or corrupted
PATS SCP message failure
P1285 V6 EMS Cylinder head over temperature sensed KOEO – page 3, or 2 M, H PCM Default: Coolant level low / leak
OBD II KOER – page 3, or – fail-safe cooling strategy Coolant contaminated
Comprehensive component Cooling system thermostat defective
monitor engine management Excessive load on engine –
drive cycle – page 7 high elevation, steep grade, trailer towing
P1288 V6 EMS CHT Sensor out of self test range KOEO – page 3, or N N PCM Default: Engine not at normal operating temperature
JAG KOER – page 3, or – CHT default value 102 °C Engine overheat condition – refer to P1285
Comprehensive component (215 °F) CHT Sensor disconnected
monitor engine management CHT Sensor to PCM circuit fault
drive cycle – page 7
PCM cooling fan circuit failure
Cooling fan module to fan motor circuit failure
Cooling fan module failure
P1289 V6 EMS CHT Sensor sense circuit high voltage KOEO – page 3, or 2 N PCM Default: CHT Sensor to cylinder head poor contact
OBD II (low temperature) KOER – page 3, or – CHT default value 102 °C CHT Sensor to PCM sensing circuit:
(215 °F) high resistance, open circuit or short circuit to
Comprehensive component high voltage
monitor engine management
drive cycle – page 7 CHT Sensor failure
P1290 V6 EMS CHT Sensor sense circuit low voltage KOEO – page 3, or 2 N PCM Default: Engine overheat condition – refer to P1285
OBD II (high temperature) KOER – page 3, or – CHT default value 102 °C CHT Sensor to PCM wiring:
(215 °F) short circuit to ground
Comprehensive component
monitor engine management CHT Sensor failure
drive cycle – page 7
P1299 V6 EMS Fail-safe cooling mode active Comprehensive component 1 M, H PCM Default: Engine overheat condition – refer to P1285
OBD II monitor engine management – fail-safe cooling strategy PCM cooling fan circuit failure
drive cycle – page 7
Cooling fan module to fan motor circuit failure
Cooling fan module failure
P1309 EMS Misfire monitor failure Misfire monitor drive cycle – 2 N None CKP Sensor fault – refer to P0320
OBD II page 4 CMP Sensor(s) fault – refer to P0340, P0341
PCM failure
P1380 EMS VVT Solenoid circuit malfunction – bank 1 KOEO – page 3, or 2 N None Bank 1 VVT solenoid valve disconnected
OBD II KOER – page 3, or Bank 1 VVT solenoid valve to PCM PWM drive
circuit fault
Comprehensive component
monitor engine management Bank 1 VVT solenoid valve power supply
drive cycle – page 7 circuit fault
Bank 1 VVT solenoid failure
P1381 EMS VVT Over advanced – bank 1 KOER – page 3, or 2 N None Bank 1 VVT solenoid valve to PCM PWM drive
OBD II Comprehensive component circuit fault
monitor engine management Bank 1 VVT actuator oil supply fault
drive cycle – page 7 Bank 1 VVT actuator stuck
P1383 EMS VVT Over retarded – bank 1 KOER – page 3, or 2 N None Bank 1 VVT solenoid valve to PCM PWM drive
OBD II Comprehensive component circuit fault
monitor engine management Bank 1 VVT actuator oil supply fault
drive cycle – page 7 Bank 1 VVT actuator stuck
P1385 EMS VVT Solenoid circuit malfunction – bank 2 KOEO – page 3, or 2 N None Bank 2 VVT solenoid valve disconnected
OBD II KOER – page 3, or Bank 2 VVT solenoid valve to PCM PWM drive
circuit fault
Comprehensive component
monitor engine management Bank 2 VVT solenoid valve power supply
drive cycle – page 7 circuit fault
Bank 2 VVT solenoid failure
P1386 EMS VVT Over advanced – bank 2 KOER – page 3, or 2 N None Bank 2 VVT solenoid valve to PCM PWM drive
OBD II Comprehensive component circuit fault
monitor engine management Bank 2 VVT actuator oil supply fault
drive cycle – page 7 Bank 2 VVT actuator stuck
P1388 EMS VVT Over retarded – bank 2 KOER – page 3, or 2 N None Bank 2 VVT solenoid valve to PCM PWM drive
OBD II Comprehensive component circuit fault
monitor engine management Bank 2 VVT actuator oil supply fault
drive cycle – page 7 Bank 2 VVT actuator stuck
P1450 EMS System unable to bleed-up fuel tank Evaporative system monitor 2 N None Restricted vapor piping – fuel tank to EVAP
OBD II vacuum drive cycle – page 6 canister purge valve
EVAP Canister purge valve stuck open
P1451 EMS EVAP Canister close valve circuit KOEO – page 3, or 2 N None EVAP Canister close valve to PCM drive circuit:
OBD II malfunction KOER – page 3, or open circuit, high resistance, short circuit
EVAP Canister close valve power supply circuit:
Evaporative system monitor open circuit, short circuit
drive cycle – page 6
EVAP Canister close valve failure
P1460 EMS A/C compressor cut-out malfunction KOEO – page 3, or N N None PCM to A/C compressor clutch relay circuit:
JAG KOER – page 3, or (PCM inhibits A/C clutch open circuit, short circuit
engagement during: engine A/C compressor clutch relay to
Comprehensive component A/C compressor circuit:
monitor engine management cranking, wide open throttle,
throttle limp home mode) open circuit, short circuit
drive cycle – page 7
A/C compressor clutch relay failure
A/C compressor clutch ground circuit:
open circuit
A/C compressor clutch failure
P1461 EMS A/C Pressure sensor high voltage KOEO – page 3, or N N None A/C Pressure sensor to PCM wiring
JAG (high pressure) KOER – page 3, or (supply, sense, reference ground):
short circuit to each other
Comprehensive component A/C Pressure sensor to PCM sensing circuit:
monitor engine management short circuit to high voltage
drive cycle – page 7
A/C Pressure sensor failure
P1462 EMS A/C Pressure sensor low voltage KOEO – page 3, or N N None A/C Pressure sensor to PCM sensing circuit:
JAG (low pressure) KOER – page 3, or open circuit or short circuit to ground
A/C Pressure sensor to PCM reference voltage
Comprehensive component circuit: open circuit or short circuit to ground
monitor engine management
drive cycle – page 7 A/C Pressure sensor to PCM reference ground
circuit: open circuit
A/C Pressure sensor failure
P1464 EMS A/C Pressure sensor out of self test range KOEO – page 3, or N N None A/C Pressure sensor to PCM wiring fault
JAG KOER – page 3, or A/C Pressure sensor failure
Comprehensive component
monitor engine management
drive cycle – page 7
P1474 EMS Radiator cooling fan control circuit KOEO – page 3, or N N None PCM to cooling fan module circuit:
JAG malfunction KOER – page 3, or open circuit, high resistance, short circuit
Cooling fan module failure
Comprehensive component
monitor engine management
drive cycle – page 7
P1500 ABS/TC Vehicle speed circuit intermittent Engine running; vehicle in N N None Rear wheel speed sensor(s) circuit(s)
JAG malfunction motion intermittent:
open circuit, high resistance, short circuit
Front wheel speed sensor(s) circuit(s)
intermittent:
open circuit, high resistance, short circuit
P1501 ABS/TC Vehicle speed out of self test range KOER – page 3 N N None Vehicle speed above 8 km/h (5 mph) preventing
JAG KOER self test from completing
P1506 EMS Idle air control over speed error KOER – page 3, or 2 N None Intake manifold air leak
OBD II Comprehensive component PCM / TACM circuit fault
monitor engine management TACM failure
drive cycle – page 7
Throttle failure
P1507 EMS Idle air control under speed error KOER – page 3, or 2 N None Engine air filter restricted / defective
OBD II Comprehensive component Engine air intake restricted / damaged
monitor engine management PCM / TACM circuit fault
drive cycle – page 7
TACM failure
Throttle failure
P1532 V6 EMS IMT Valve control circuit malfunction – KOEO – page 3, or N N None IMT Valve (top) disconnected
JAG top valve Comprehensive component IMT Valve (top) to PCM drive circuit fault
monitor engine management IMT Valve (top) power supply circuit fault
drive cycle – page 7
IMT Valve (top) failure
P1534 EMS Air bag(s) deployed (Restraints control KOEO – page 3, or N A, M None PCM to RCM airbag deployed circuit:
JAG module (RCM) input to PCM) circuit KOER – page 3, or open circuit, high resistance, short circuit to
malfunction ground
Comprehensive component RCM fault
monitor engine management
drive cycle – page 7
P1549 V6 EMS IMT Valve control circuit malfunction – KOEO – page 3, or N N None IMT Valve (bottom) disconnected
JAG bottom valve Comprehensive component IMT Valve (bottom) to PCM drive circuit fault
monitor engine management IMT Valve (bottom) power supply circuit fault
drive cycle – page 7
IMT Valve (bottom) failure
P1565 EMS Speed control command switch input Drive vehicle; operate all N M, S PCM Default: Speed control steering wheel switches to PCM
JAG (steering wheel switches) out of range – speed control steering wheel – speed control inhibited signal circuit (PCM pin FH1-57):
high voltage switches short circuit to B+ V
Speed control steering wheel switch(es) failure
P1566 EMS Speed control command switch input Drive vehicle; operate all N M, S PCM Default: Speed control steering wheel switches to
JAG (steering wheel switches) out of range – speed control steering wheel – speed control inhibited PCM wiring:
low voltage switches open circuit, high resistance, short circuit to
ground
Speed control steering wheel switch(es) failure
P1572 EMS Brake cancel switch out of self test range Ignition ON; operate brake 2 M, S PCM Default: Brake cancel switch to PCM signal circuit:
OBD II pedal – speed control inhibited open circuit, high resistance, short circuit
Brake cancel switch power supply circuit:
open circuit, short circuit
Brake cancel switch failure
P1573 EMS TP Sensor signals malfunction – KOEO – page 3, or 2 R, M Throttle limp home mode: TP Sensor to PCM sensing circuits
OBD II more than one signal failure KOER – page 3, or – high idle speed (sensor pins 1, 2, 10):
open circuit, high resistance, short circuit
Comprehensive component – no accelerator pedal TP Sensor to PCM reference voltage circuits
monitor engine management response (sensor pins 4, 3):
drive cycle – page 7 open circuit, high resistance, short circuit
TP Sensor to PCM reference ground circuits
(sensor pins 6, 7):
open circuit, high resistance, short circuit
TP Sensor failure
P1574 EMS TP Sensor signals disagree – KOEO – page 3, or N A, M None (as long as normal Refer to P1573 Possible Causes
JAG one signal failure KOER – page 3, or signals are received from the
remaining two sensors)
Comprehensive component
monitor engine management
drive cycle – page 7
P1576 EMS APP Sensor signals malfunction – KOEO – page 3, or 2 R, M Throttle limp home mode: APP Sensor to PCM sensing circuits
OBD II more than one signal failure KOER – page 3, or – high idle speed (sensor pins 4, 5, 7):
open circuit, high resistance, short circuit
Comprehensive component – no accelerator pedal APP Sensor to PCM reference voltage circuits
monitor engine management response (sensor pins 3, 8, 10):
drive cycle – page 7 open circuit, high resistance, short circuit
APP Sensor to PCM reference ground circuits
(sensor pins 2, 6, 9):
open circuit, high resistance, short circuit
APP Sensor failure
P1577 EMS APP Sensor signals disagree – KOEO – page 3, or N A, M None (as long as normal Refer to P1576 Possible Causes
JAG one signal failure KOER – page 3, or signals are received from the
remaining two sensors)
Comprehensive component
monitor engine management
drive cycle – page 7
P1580 EMS Internal throttle monitor PCM override KOEO – page 3, or 2 R, M Throttle limp home mode: TP Sensor circuit fault – TP Sensor DTC(s)
OBD II (Electronic throttle system failure) KOER – page 3, or – high idle speed flagged
Throttle circuit fault – throttle DTC(s) flagged
Comprehensive component – no accelerator pedal
monitor engine management response Uneven throttle valve movement due to debris
drive cycle – page 7 on throttle valve and/or shaft (Test for smooth
(Engine may stop if fuel actuation by moving the throttle valve by hand
injection is canceled) while the ignition is switched OFF.)
PCM Failure
P1581 EMS PCM Throttle monitor malfunction KOEO – page 3, or N A, M PCM Default: PCM Failure
JAG KOER – page 3, or – cruise control inhibited
Comprehensive component – possible engine disable
monitor engine management
drive cycle – page 7
P1582 EMS Throttle data recorder data available KOEO – page 3, or N N None Vehicle impact
JAG KOER – page 3, or To reuse PCM:
Comprehensive component 100 Ignition key cycles, then
monitor engine management Clear DTC using PDU / WDS, or
drive cycle – page 7
Additional 40 ignition key cycles
P1584 EMS Throttle actuation malfunction KOEO – page 3, or 2 A, M PCM Default: Throttle Body failure
OBD II KOER – page 3, or Failure Mode #1:
Comprehensive component TACM operates in open loop
monitor engine management control. (Engine may stall and
drive cycle – page 7 throttle response will be
harsh.)
Failure Mode #2:
TACM operates in normal
closed loop mode but with
reduced torque output.
(Engine may stall.)
P1585 EMS TACM self test failure KOEO – page 3, or 2 R, M PCM Default: TACM Failure (Throttle Body failure)
OBD II (Electronic throttle system failure) KOER – page 3, or – engine will stop, or
Comprehensive component possibly run at very low
monitor engine management idle speed
drive cycle – page 7
P1586 EMS TACM to PCM communication (SCP) KOEO – page 3, or 2 A, M PCM Default: TACM power supply or ground circuits:
OBD II failure KOER – page 3, or – engine will stop, or open circuit, high resistance
possibly run at very low SCP circuit fault – U Code flagged
Comprehensive component
monitor engine management idle speed TACM Failure (Throttle Body failure)
drive cycle – page 7
P1587 EMS PCM to TACM throttle command KOEO – page 3, or 2 A, R*, If only one command circuit PCM to TACM redundant control circuits
OBD II redundancy circuit malfunction KOER – page 3, or M fails: None (TACM pins 2, 3):
open circuit, high resistance, short circuit
Comprehensive component If both command circuits fail:
TACM Failure (Throttle Body failure)
monitor engine management Throttle limp home mode
drive cycle – page 7 PCM Failure
– high idle speed
– no accelerator pedal
response
R* If both command circuits
fail
P1588 EMS Throttle return spring failure detected KOEO – page 3, or N A, M Throttle limp home mode Throttle body failure
JAG KOER – page 3, or
Comprehensive component
monitor engine management
drive cycle – page 7
P1589 EMS TACM unable to control throttle valve to KOEO – page 3, or 2 R, M PCM Default: Throttle valve stuck due to obstruction
OBD II commanded throttle angle KOER – page 3, or – engine will stop, or Throttle body failure
Comprehensive component possibly run at very low
monitor engine management idle speed
drive cycle – page 7
P1633 PCM Keep alive memory (KAM) voltage too low Drive vehicle 1 N None Vehicle battery voltage low
OBD II Battery power supply to PCM interrupted for
longer than 20 seconds during engine
operation
P1635 EMS Wheel / axle ratio out of acceptable range Drive vehicle N N None Incorrect size tire(s) fitted to vehicle
JAG Incorrect size wheel(s) fitted to vehicle
P1636 PCM PCM Internal communication error Comprehensive component 2 N PCM Default: PCM Failure
OBD II monitor engine management – self test partially inhibited
drive cycle – page 7
P1650 EMS PSP Switch out of self test range KOEO – page 3, or N N None PSP switch to PCM signal circuit:
JAG KOER – page 3 open circuit, high resistance, short circuit
PSP switch reference ground circuit (to splice):
open circuit
PSP switch failure
P1700 TRANS Transmission intermediate failure KOEO – page 3, or 2 N PCM Default: Clear DTC 1700
OBD II KOER – page 3, or – 2nd and 5th gears only Diagnose and repair other flagged DTCs
Comprehensive component Conduct drive cycle – if P1700 reflags:
monitor transmission drive transmission mechanical failure (direct one-
cycle – page 8 way clutch)
P1702 TRANS Range sensor circuit intermittent KOEO – page 3, or N N PCM Defaults to DRIVE (to Gear selector cable incorrectly adjusted
JAG malfunction KOER – page 3, or maintain all five gears) Range sensor circuit intermittent:
J Gate gear selected open circuit or short circuit
Comprehensive component
monitor transmission drive illumination extinguished Range sensor failure
cycle – page 8 (Harsh shifts)
P1704 TRANS Range sensor circuit not indicating P / N KOEO – page 3, or N T ABS/TCCM, DSCCM Selector not in P / N
JAG during self test KOER – page 3 Default: Range sensor incorrect alignment
– traction control inhibited Gear selector cable incorrectly adjusted
Gear selector mechanical failure
Range sensor failure
P1705 TRANS Range sensor out of self test range KOEO – page 3, or N N None Range sensor incorrect alignment
JAG KOER – page 3 Gear selector cable incorrectly adjusted
Gear selector mechanical failure
Range sensor failure
P1711 TRANS TFT Out of self test range KOEO – page 3, or N T ABS/TCCM, DSCCM Transmission not at normal operating
JAG KOER – page 3 Default: temperature
– traction control inhibited TFT Sense circuit:
short circuit, high resistance, open circuit
TFT Sensor failure
P1713 TRANS TFT Signal – no change at low range during Comprehensive component N T PCM Default: TFT Sensor circuit:
JAG vehicle operation monitor transmission drive – TFT calculated from high resistance, open circuit
cycle – page 8 ECT (V8) / CHT (V6) TFT Sensor failure
ABS/TCCM, DSCCM
Default:
– traction control inhibited
P1714 TRANS Shift solenoid 1 stuck – mechanical failure Comprehensive component 2 A, M PCM Default: Shift solenoid 1 mechanical failure
OBD II monitor transmission drive – 1st, 2nd, 3rd shift pattern
cycle – page 8 or
– 3rd, 2nd, 3rd, 4th, 5th shift
pattern
(Shift pattern depends on
position of stuck solenoid)
P1715 TRANS Shift solenoid 2 stuck – mechanical failure Comprehensive component 2 A, M PCM Default: Shift solenoid 2 mechanical failure
OBD II monitor transmission drive – 1st, 2nd, 4th, 5th shift
cycle – page 8 pattern or
– 3rd, 2nd, 3rd, 4th, 5th shift
pattern
(Shift pattern depends on
position of stuck solenoid)
P1716 TRANS Shift solenoid 3 stuck – mechanical failure Comprehensive component 2 A, M PCM Default: Shift solenoid 3 mechanical failure
OBD II monitor transmission drive – 1st, 1st, 3rd, 4th, 5th shift
cycle – page 8 pattern or
– normal shift pattern
(Shift pattern depends on
position of stuck solenoid)
P1717 TRANS Shift solenoid 4 stuck – mechanical failure Comprehensive component N A, M PCM Default: Shift solenoid 4 mechanical failure
JAG monitor transmission drive – DRIVE – normal shift
cycle – page 8 pattern
– Manual – 2, 3, 4 inhibited
P1718 TRANS TFT Signal – no change at high range Comprehensive component N T PCM Default: TFT Sensor circuit short circuit
JAG during vehicle operation monitor transmission drive – TFT calculated from TFT Sensor failure
cycle – page 8 ECT (V8) / CHT (V6)
ABS/TCCM, DSCCM
Default:
– traction control inhibited
P1740 TRANS TCC solenoid stuck – mechanical failure Comprehensive component 2 A, M None TCC solenoid mechanical failure
OBD II monitor transmission drive (TCC applied / released
cycle – page 8 depending on position of
stuck solenoid)
P1746 TRANS Pressure control solenoid 1 circuit low KOEO – page 3, or N A, M, T PCM Default: Pressure control solenoid 1 drive circuit:
JAG voltage KOER – page 3, or – normal shift pattern short circuit to ground
Pressure control solenoid 1 failure
Comprehensive component (Harsh shifts)
monitor transmission drive Transmission mechanical failure
cycle – page 8 (other DTCs logged)
P1747 TRANS Pressure control solenoid 1 circuit high KOEO – page 3, or 2 A, M PCM Default: Pressure control solenoid 1 drive circuit:
OBD II voltage KOER – page 3, or – 1st, 2nd, 4th, 5th shift short circuit to B+ V; open circuit
pattern Pressure control solenoid 1 failure
Comprehensive component
monitor transmission drive (Harsh shifts) Transmission mechanical failure
cycle – page 8 (other DTCs logged)
P1760 TRANS Pressure control solenoid 1 drive circuit KOEO – page 3, or N A, M PCM Default: Pressure control solenoid 1 drive circuit:
JAG intermittent low voltage KOER – page 3, or – 1st, 2nd, 4th, 5th shift intermittent short circuit to ground
Comprehensive component pattern
monitor transmission drive
cycle – page 8
P1780 TRANS D – 4th switch out of self test range KOEO – page 3, or 2 A, M PCM Default: D – 4th Switch power supply open circuit
OBD II KOER – page 3, or – Manual 4th inhibited D – 4th Switch / PCM sense circuit:
short circuit, high resistance, open circuit
Comprehensive component
monitor transmission drive D – 4th Switch failure
cycle – page 8
P1783 TRANS Transmission over temperature condition Comprehensive component N T PCM Default: Excessive vehicle load
JAG indicated – >127 °C (270 °F) monitor transmission drive – TCC Lock-up in all gears Transmission fluid level low
cycle – page 8
ABS/TCCM, DSCCM Transmission fluid contaminated
Default: Transmission fluid cooler failure (clogged)
– traction control inhibited TFT Sensor fault – refer to P0712
P1788 TRANS Pressure control solenoid 2 circuit high KOEO – page 3, or N T PCM Default: Pressure control solenoid 2 drive circuit:
JAG voltage KOER – page 3, or – normal shift pattern short circuit to B+ V; open circuit
Pressure control solenoid 2 failure
Comprehensive component ABS/TCCM, DSCCM
monitor transmission drive Default: Transmission mechanical failure
cycle – page 8 (other DTCs logged)
– traction control inhibited
(Harsh shifts)
P1789 TRANS Pressure control solenoid 2 drive circuit KOEO – page 3, or 2 A, M PCM Default: Pressure control solenoid 2 drive circuit:
OBD II low voltage KOER – page 3, or – 1st, 1st, 3rd, 4th, 4th shift short circuit to ground
pattern Pressure control solenoid 2 failure
Comprehensive component
monitor transmission drive (Harsh shifts) Transmission mechanical failure
cycle – page 8 (other DTCs logged)
REFERENCE: It is recommended that the applicable “Electrical Guide” be referenced when using the information
contained in this document.
SYS The powertrain system with which the DTC is associated – EMS (ALL SYSTEMS), V6 EMS, V8 EMS, V8 SC EMS, TRANS, DSC.
DTC retrieval tools:
OBD II – indicates that the DTC is an OBD II code and can be accessed via a generic scan tool or WDS.
JAG – indicates that the DTC is not an OBD II code and is accessed only via WDS.
CHECK ENGINE MIL 1 1 TRIP – indicates that the CHECK ENGINE MIL is activated by a fault occurring during ONE “TRIP”.
(CK ENG) 2 2 TRIPS – indicates that the CHECK ENGINE MIL is activated by a fault occurring during TWO CONSECUTIVE “TRIPS”.
Refer to page 3 for definition of OBD “TRIP”.
N NO – indicates that the CHECK ENGINE MIL is not activated.
POSSIBLE CAUSES Possible causes are listed in the order of diagnostic checking.
HIGH VOLTAGE – High voltage can be either sensor supply voltage (5 volts) or B+ voltage.
2 1 2 1
4 3 4 3
6 5 6 5
8 7
OBD “TRIPS”
The OBD system defines 1 TRIP as an ignition cycle (ignition key OFF; wait 30 seconds; ignition key ON) plus a minimum engine coolant temperature increase of
22 °C (40 °F) after which, the engine coolant temperature has to reach a minimum of 71°C (160 °F).
P0010 EMS VVT circuit malfunction – bank 1 Idle engine 30 seconds 2 N ECM Default: PI1 VVT solenoid valve disconnected
OBD II Accelerate from stop through – Bank 1 VVT hold current set at -109 VVT solenoid valve to ECM PWM drive circuit:
complete engine rpm range a constant value of open circuit, short circuit, high resistance
Coast to a stop 450 mA (V6) VVT solenoid failure
Drive the vehicle steadily 520 mA (V8)
between 48 – 97 km/h (30 –
60 mph) for 5 minutes; coast
to a stop
Accelerate smoothly through
complete accelerator pedal
travel; coast to a stop
Idle engine 30 seconds
P0020 EMS VVT circuit malfunction – bank 2 Idle engine 30 seconds 2 N ECM Default: PI1 VVT solenoid valve disconnected
OBD II Accelerate from stop through – Bank 2 VVT hold current set at -110 VVT solenoid valve to ECM PWM drive circuit:
complete engine rpm range; a constant value of open circuit, short circuit, high resistance
coast to a stop 450 mA (V6) VVT solenoid failure
Drive the vehicle steadily 520 mA (V8)
between 48 – 97 km/h (30 –
60 mph) for 5 minutes; coast
to a stop
Accelerate smoothly through
complete accelerator pedal
travel; coast to a stop
Idle engine 30 seconds
P0031 EMS HO2 Sensor heater control circuit Heated oxygen sensors 2 N ECM Default: PI1 HO2 Sensor 1/1 heater power supply circuit:
OBD II low current – monitor drive cycle – page 5 – Bank 1 closed loop fuel -001 open circuit
bank 1, upstream (1/1) (Oxygen sensor heaters) metering and adaptive fuel -002 HO2 Sensor 1/1 heater control circuit:
metering inhibited -029 open circuit, high resistance
-030
– Canister purge inhibited HO2 Sensor 1/1 heater ground circuit(s) fault
(PI1-029, PI1-030)
– Bank 1 upstream HO2S
heater control circuit switched HO2 Sensor 1/1 heater failure
off
P0032 EMS HO2 Sensor heater control circuit Heated oxygen sensors 2 N ECM Default: PI1 HO2 Sensor 1/1 heater control circuit:
OBD II high current – monitor drive cycle – page 5 – Bank 1 closed loop fuel -001 short circuit to ground
bank 1, upstream (1/1) (Oxygen sensor heaters) metering and adaptive fuel -002 HO2 Sensor 1/1 heater ground circuit(s) fault
metering inhibited -029 (PI1-029, PI1-030)
-030
– Canister purge inhibited HO2 Sensor 1/1 heater failure
– Bank 1 upstream HO2S
heater control circuit switched
off
P0037 EMS HO2 Sensor heater control circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 1/2 heater control circuit:
OBD II low resistance – monitor drive cycle – page 5 -092 short circuit to ground
bank 1, downstream (1/2) (Oxygen sensor heaters) HO2 Sensor 1/2 heater failure
P0038 EMS HO2 Sensor heater control circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 1/2 heater control circuit:
OBD II high resistance – monitor drive cycle – page 5 -092 open circuit; high resistance
bank 1, downstream (1/2) (Oxygen sensor heaters) HO2 Sensor 1/2 heater failure
P0051 EMS HO2 Sensor heater control circuit Heated oxygen sensors 2 N ECM Default: PI1 HO2 Sensor 2/1 heater power supply circuit:
OBD II low current – monitor drive cycle – page 5 – Bank 2 closed loop fuel -055 open circuit
bank 2, upstream (2/1) (Oxygen sensor heaters) metering and adaptive fuel -056 HO2 Sensor 2/1 heater control circuit:
metering inhibited -081 open circuit, high resistance
-082
– Canister purge inhibited HO2 Sensor 2/1 heater ground circuit(s) fault
(PI1-081, PI1-082)
– Bank 2 upstream HO2S
heater control circuit switched HO2 Sensor 2/1 heater failure
off
P0052 EMS HO2 Sensor heater control circuit Heated oxygen sensors 2 N ECM Default: PI1 HO2 Sensor 2/1 heater control circuit:
OBD II high current – monitor drive cycle – page 5 – Bank 2 closed loop fuel -055 short circuit to ground
bank 2, upstream (2/1) (Oxygen sensor heaters) metering and adaptive fuel -056 HO2 Sensor 2/1 heater ground circuit(s) fault
metering inhibited -081 (PI1-081, PI1-082)
-082
– Canister purge inhibited HO2 Sensor 2/1 heater failure
– Bank 2 upstream HO2S
heater control circuit switched
off
P0057 EMS HO2 Sensor heater control circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 2/2 heater control circuit:
OBD II low resistance – monitor drive cycle – page 5 -093 short circuit to ground
bank 2, downstream (2/2) (Oxygen sensor heaters) HO2 Sensor 2/2 heater failure
P0058 EMS HO2 Sensor heater control circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 2/2 heater control circuit:
OBD II high resistance – monitor drive cycle – page 5 -093 open circuit; high resistance
bank 2, downstream (2/2) (Oxygen sensor heaters) HO2 Sensor 2/2 heater failure
P0096 V8 SC IAT Sensor 2 circuit range / Engine coolant temperature 2 A ECM Default: PI1 IAT Sensor 2 disconnected
EMS performance < 40 °C (104 °F) – Default value of 70 °C (158 °F) -072 IAT Sensor 2 to ECM sensing circuit:
OBD II Ambient temperature used open circuit
< 40 °C (104 °F) IAT Sensor 2 failure
Engine coolant temperature
and ambient temperature
within 10 °C (20 °F) of each
other
Start engine and drive above
1500 rpm at a steady speed
for a minimum of 2 minutes
P0097 V8 SC IAT Sensor 2 circuit high voltage Ignition ON 10 seconds 2 A ECM Default: PI1 IAT Sensor 2 disconnected
EMS (low air temperature) – Default value of 70 °C (158 °F) -072 IAT Sensor 2 to ECM wiring:
OBD II used open circuit or high resistance
IAT Sensor 2 to ECM sensing circuit:
short circuit to B+ voltage
IAT Sensor 2 failure
P0098 V8 SC IAT Sensor 2 circuit low voltage Ignition ON 10 seconds 2 A ECM Default: PI1 IAT Sensor 2 to ECM wiring:
EMS (high air temperature) – Default value of 70 °C (158 °F) -072 short circuit to ground
OBD II used IAT Sensor 2 failure
P0101 EMS MAF Sensor circuit range / Fuel level > 25%. 2 A ECM Default: PI1 Blocked air cleaner
OBD II performance Start engine and bring to – Default air mass used -044 Air intake leak
normal operating temperature – Adaptive fuel metering Engine breather leak
> 82 °C (180 °F) inhibited Throttle control malfunction
Drive the vehicle steadily in – Catalyst warm up ignition
4th or 5th gear on a level road MAF Sensor to ECM sensing circuit:
retard inhibited high resistance, intermittent short circuit
between to ground
1700 – 2300 rpm (V6), – Canister purge inhibited
1200 – 1800 rpm (V8); – Maximum engine speed MAF Sensor supply circuit: high resistance
hold the engine speed reduced MAF Sensor failure
constant for 40 seconds while
maintaining a steady throttle Throttle adaption fault (check throttle position
voltage at Ignition ON)
P0102 EMS MAF Sensor circuit low voltage Ignition ON 10 seconds 2 A ECM Default: PI1 Blocked air cleaner
OBD II – Default air mass used -044 Air intake leak between MAF Sensor and
throttle
– Adaptive fuel metering
inhibited MAF Sensor to ECM sensing circuit:
high resistance, open circuit, intermittent
– Catalyst warm up ignition short circuit to ground
retard inhibited
MAF Sensor supply circuit:
– Canister purge inhibited open circuit, short circuit to ground
– Maximum engine speed MAF Sensor failure
reduced
P0103 EMS MAF Sensor circuit high voltage Ignition ON 10 seconds 2 A ECM Default: PI1 MAF Sensor to ECM sensing circuit:
OBD II – Default air mass used -044 short circuit to B+ voltage
-045 MAF Sensor to ECM sensor ground circuit:
– Adaptive fuel metering open circuit
inhibited -046
MAF Sensor failure
– Catalyst warm up ignition
retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0105 EMS MAP Sensor circuit malfunction Fuel level > 25% 2 N ECM Default: PI1 Intake manifold air leak (loose or missing
-127 component)
OBD II Start engine and bring to – Default value of 1.013 BAR
normal operating temperature (29.92 in hg) used MAP Sensor to ECM circuit(s) fault
> 82 °C (180 °F) MAP Sensor failure
Drive the vehicle steadily in Throttle adaption fault (check throttle position
4th or 5th gear on a level road voltage at Ignition ON)
between
1700 – 2300 rpm (V6),
1200 – 1800 rpm (V8);
hold the engine speed
constant for 40 seconds while
maintaining a steady throttle
P0106 EMS BARO Sensor circuit range / Engine temperature cool 2 N ECM Default: — BARO Sensor failure (internal ECM fault)
OBD II performance (cooling fans not running) – Default value of 1 BAR (29.53
Remove ignition key for 20 in hg) used
seconds (cooling fans not
running)
Ignition key in, position II for 5
seconds (do not start)
Repeat cycle twice more
P0107 EMS BARO Sensor circuit low voltage Ignition ON 10 seconds 2 N ECM Default: — BARO Sensor failure (internal ECM fault)
OBD II – Default value of 1 BAR (29.53
in hg) used
P0108 EMS BARO Sensor circuit high voltage Ignition ON 10 seconds 2 N ECM Default: — BARO Sensor failure (internal ECM fault)
OBD II – Default value of 1 BAR (29.53
in hg) used
P0111 EMS IAT Sensor circuit range / Engine OFF; coolant 2 N ECM Default: PI1 Blocked air cleaner
OBD II performance temperature <35 °C (95 °F) – Default value substituted -071 Air intake leak
Start engine and hold 3000 25 °C (77 °F) (V6) Engine breather leak
rpm in P or N for 30 seconds 50 °C (122 °F) V8 IAT Sensor to ECM wiring:
open circuit or high resistance
IAT Sensor to ECM sensing circuit:
short circuit to high voltage
IAT Sensor failure
P0112 EMS IAT Sensor circuit high voltage Ignition ON 10 seconds 2 N ECM Default: PI1 IAT Sensor disconnected
OBD II (low air temperature) – Default value substituted -071 IAT Sensor to ECM wiring:
open circuit or high resistance
25 °C (77 °F) (V6)
50 °C (122 °F) V8 IAT Sensor to ECM sensing circuit:
short circuit to B+ voltage
IAT Sensor failure
P0113 EMS IAT Sensor circuit low voltage Ignition ON 10 seconds 2 N ECM Default: PI1 IAT Sensor to ECM wiring:
OBD II (high air temperature) – Default value substituted -071 short circuit to ground
IAT Sensor failure
25 °C (77 °F) (V6)
50 °C (122 °F) V8
P0116 EMS ECT Sensor circuit range / Engine coolant temperature 2 A ECM Default: PI1 ECT Sensor disconnected
OBD II performance and ambient temperature – EOT value substituted (no -070 Low coolant level
within 10 °C (20 °F) of each greater than 95 °C (203 °F)
other Contaminated coolant
– Closed loop fuel metering Engine thermostat failure
Start engine and drive the inhibited
vehicle steadily in 4th or 5th ECT Sensor to ECM sensing circuit:
gear above 1700 rpm until the – Adaptive fuel metering open circuit, high resistance when hot,
engine coolant temperature inhibited intermittent high resistance
reaches 80 °C (176 °F) – Catalyst warm-up ignition ECT Sensor failure
CAUTION: Overheating is retard inhibited
possible if the ECT sensor is – Canister purge inhibited
faulty and cooling fans do not
operate – Maximum engine speed
reduced
P0117 EMS ECT Sensor circuit high voltage Ignition ON 10 seconds 2 A ECM Default: PI1 ECT Sensor disconnected
OBD II (low coolant temperature) – EOT value substituted (no -070 ECT Sensor to ECM sensing circuit:
greater than 95 °C (203 °F) high resistance, open circuit,
short circuit to B+ voltage
– Closed loop fuel metering
inhibited ECT Sensor failure
– Adaptive fuel metering
inhibited
– Catalyst warm-up ignition
retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0118 EMS ECT Sensor circuit low voltage Ignition ON 10 seconds 2 A ECM Default: PI1 Engine overheat condition
OBD II (high coolant temperature) – EOT value substituted (no -070 ECT Sensor to ECM wiring:
greater than 95 °C (203 °F) short circuit to ground
– Closed loop fuel metering ECT Sensor failure
inhibited
– Adaptive fuel metering
inhibited
– Catalyst warm-up ignition
retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0121 EMS TP Sensor range / performance Battery voltage > 10 volts 2 R ECM Default: PI1 TP Sensor to ECM wiring:
OBD II (TP1 compared to TP2) Ignition ON – Throttle motor and throttle -075 open circuit, high resistance
motor relay disabled -076 TP Sensor to ECM sensing circuits (TP1 or
Slowly press accelerator pedal TP2): short circuit to B+ voltage
to the floor over a 5 second – Throttle valve opening set to
period default value TP Sensor failure
Slowly return the pedal to rest – Idle speed controlled by fuel
Repeat 3 times injection intervention
– Idle speed adaption inhibited
P0122 EMS TP Sensor circuit 1 low voltage Battery voltage > 10 volts 2 R ECM Default: PI1 TP Sensor to ECM sensing circuit (TP1):
OBD II Ignition ON – Throttle motor and throttle -075 open circuit, short circuit to ground, high
resistance
Slowly press accelerator pedal motor relay disabled
TP Sensor failure
to the floor over a 5 second – Throttle valve opening set to
period default value
Slowly return the pedal to rest – Idle speed controlled by fuel
Repeat 3 times injection intervention
– Idle speed adaption inhibited
P0123 EMS TP Sensor circuit 1 high voltage Battery voltage > 10 volts 2 R ECM Default: PI1 TP Sensor to ECM sensing circuit (TP1):
OBD II Ignition ON – Throttle motor and throttle -075 short circuit to high voltage
motor relay disabled TP Sensor failure
Slowly press accelerator pedal
to the floor over a 5 second – Throttle valve opening set to
period default value
Slowly return the pedal to rest – Idle speed controlled by fuel
Repeat 3 times injection intervention
– Idle speed adaption inhibited
P0125 EMS ECT Sensor response Engine coolant temperature 2 A ECM Default: PI1 ECT Sensor disconnected
OBD II (for closed loop fuel control) and ambient temperature – EOT value substituted (no -070 Low coolant level
within 10 °C (20 °F) of each greater than 95 °C (203 °F)
other Contaminated coolant
(Coolant thermostat monitor) – Closed loop fuel metering Engine coolant thermostat failure
Start engine and drive the inhibited
vehicle steadily in 4th or 5th ECT Sensor to ECM sensing circuit:
gear above 1700 rpm until the – Adaptive fuel metering high resistance, open circuit or short circuit
engine coolant temperature inhibited to high voltage
reaches 80 °C (176 °F) – Catalyst warm-up ignition Engine cooling fan stuck on high speed
CAUTION: Overheating is retard inhibited Above normal air flow through engine
possible if the ECT sensor is – Canister purge inhibited compartment due to accident damage
faulty and cooling fans do not and/or missing panels
operate – Maximum engine speed
reduced
P0128 EMS Coolant thermostat range / Engine OFF; coolant 2 N None — Contaminated coolant
OBD II performance temperature < 35 °C (95 °F) Engine coolant thermostat failure
Start engine and drive until ECT Sensor failure
normal engine operating (ECT Sensor DTC(s) also flagged)
temperature > 85 °C (180 °F)
P0131 EMS HO2 Sensor sense circuit low Heated oxygen sensors 2 N None PI1 HO2 Sensor 1/1 disconnected
OBD II current – bank 1, upstream (1/1) monitor drive cycle – page 5 -083 HO2 Sensor 1/1 to ECM variable current
(Upstream oxygen sensors) -084 circuit fault (HO2 Sensor pin 3)
(Universal oxygen sensor: lean ECM to HO2 Sensor 1/1 constant current
condition at ECM – high current at circuit fault (HO2 Sensor pin 4)
sensor) HO2 Sensor 1/1 failure
P0132 EMS HO2 Sensor sense circuit high Heated oxygen sensors 2 N None PI1 HO2 Sensor 1/1 disconnected
OBD II current – bank 1, upstream (1/1) monitor drive cycle – page 5 -083 HO2 Sensor 1/1 to ECM variable current
(Upstream oxygen sensors) -084 circuit fault (HO2 Sensor pin 3)
(Universal oxygen sensor: rich ECM to HO2 Sensor 1/1 constant current
condition at ECM – low current at circuit fault (HO2 Sensor pin 4)
sensor) HO2 Sensor 1/1 failure
P0133 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N ECM Default: PI1 Engine misfire
OBD II slow response – monitor drive cycle – page 5 – Bank 1 closed loop fuel -083 HO2 Sensor 1/1 disconnected
bank 1, upstream (1/1) (Upstream oxygen sensors) metering inhibited -084
HO2 Sensor 1/1 mechanical damage
– Canister purge inhibited HO2 Sensor 1/1 to ECM wiring fault
HO2 Sensor 1/1 short circuit to ground
HO2 Sensor 1/1 to ECM wiring shield
open circuit
HO2 Sensor 1/1 heater circuit fault
Exhaust leak
Low exhaust temperature
Injector flow partially blocked
Catalyst efficiency decrease
HO2 Sensor 1/1 failure
P0137 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 1/2 disconnected
OBD II low voltage – monitor drive cycle – page 5 -128 HO2 Sensor 1/2 to ECM wiring open circuit
bank 1, downstream (1/2) (Downstream oxygen HO2 Sensor 1/2 short circuit to ground
sensors)
HO2 Sensor 1/2 failure
P0138 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 1/2 sensing circuit:
OBD II high voltage – monitor drive cycle – page 5 -128 short circuit to high voltage
bank 1, downstream (1/2) (Downstream oxygen HO2 Sensor 1/2 ground (BRD – braided shield)
sensors) open circuit
HO2 Sensor 1/2 failure
P0140 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 1/2 disconnected
OBD II no activity – monitor drive cycle – page 5 -128 HO2 Sensor 1/2 mechanical damage
bank 1, downstream (1/2) (Downstream oxygen HO2 Sensor 1/2 to ECM wiring open circuit
sensors)
HO2 Sensor 1/2 sensing circuit:
short circuit to high voltage
HO2 Sensor 1/2 short circuit to ground
HO2 Sensor 1/2 ground (BRD – braided shield)
open circuit
Exhaust leak
Low exhaust temperature
HO2 Sensor 1/2 failure
P0151 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 2/1 disconnected
OBD II low current – monitor drive cycle – page 5 -107 HO2 Sensor 2/1 to ECM variable current
bank 2, upstream (2/1) (Upstream oxygen sensors) -108 circuit fault (HO2 Sensor pin 3)
ECM to HO2 Sensor 2/1 constant current
(Universal oxygen sensor: lean circuit fault (HO2 Sensor pin 4)
condition at ECM – high current at HO2 Sensor 2/1 failure
sensor)
P0152 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 2/1 disconnected
OBD II high current – monitor drive cycle – page 5 -107 HO2 Sensor 2/1 to ECM variable current
bank 2, upstream (2/1) (Upstream oxygen sensors) -108 circuit fault (HO2 Sensor pin 3)
ECM to HO2 Sensor 2/1 constant current
(Universal oxygen sensor: rich circuit fault (HO2 Sensor pin 4)
condition at ECM – low current at HO2 Sensor 2/1 failure
sensor)
P0153 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N ECM Default: PI1 Engine misfire
OBD II slow response – monitor drive cycle – page 5 – Bank 1 closed loop fuel -107 HO2 Sensor 2/1 disconnected
bank 2, upstream (2/1) (Upstream oxygen sensors) metering inhibited -108
HO2 Sensor 2/1 mechanical damage
– Canister purge inhibited HO2 Sensor 2/1 to ECM wiring fault
HO2 Sensor 2/1 short circuit to ground
HO2 Sensor 2/1 to ECM wiring shield
open circuit
HO2 Sensor 2/1 heater circuit fault
Exhaust leak
Low exhaust temperature
Injector flow partially blocked
Catalyst efficiency decrease
HO2 Sensor 2/1 failure
P0157 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 2/2 disconnected
OBD II low voltage – monitor drive cycle – page 5 -129 HO2 Sensor 2/2 to ECM wiring open circuit
bank 2, downstream (2/2) (Downstream oxygen HO2 Sensor 2/2 short circuit to ground
sensors)
HO2 Sensor 2/2 failure
P0158 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 2/2 sensing circuit:
OBD II high voltage – monitor drive cycle – page 5 -129 short circuit to high voltage
bank 2, downstream (2/2) (Downstream oxygen HO2 Sensor 2/2 ground (BRD – braided shield)
sensors) open circuit
HO2 Sensor 2/2 failure
P0160 EMS HO2 Sensor sense circuit Heated oxygen sensors 2 N None PI1 HO2 Sensor 2/2 disconnected
OBD II no activity – monitor drive cycle – page 5 -129 HO2 Sensor 2/2 mechanical damage
bank 2, downstream (2/2) (Downstream oxygen HO2 Sensor 2/2 to ECM wiring open circuit
sensors)
HO2 Sensor 2/2 sensing circuit short circuit to
high voltage
HO2 Sensor 2/2 short circuit to ground
HO2 Sensor 2/2 ground (BRD – braided shield)
open circuit
Exhaust leak
Low exhaust temperature
HO2 Sensor 2/2 failure
P0171 EMS Bank 1 combustion too lean Start engine and bring to 2 N ECM Default: — Engine misfire
OBD II normal operating temperature – Bank 1 catalyst warm-up Air intake leak between MAF Sensor and
> 82 °C (180 °F) ignition retard inhibited cylinder head
Idle for 10 minutes – Bank 1 closed loop fuel Fuel filter / system restriction
metering inhibited Fuel injector restriction
– Canister purge inhibited IP Sensor fault (low fuel pressure)
– Maximum engine speed Low fuel pump output
reduced HO2 Sensor(s) (1/1, 1/2)
harness wiring condition fault
EFT Sensor fault (low fuel temperature)
MAF Sensor fault (low intake air flow)
Exhaust leak (before catalyst)
ECM receiving incorrect signal from one or
more of the following components:
ECT Sensor, MAF Sensor, IAT Sensor,
IP Sensor, EFT Sensor, TP Sensor
P0172 EMS Bank 1 combustion too rich Start engine and bring to 2 N ECM Default: — Restricted air filter
OBD II normal operating temperature – Bank 1 catalyst warm-up Leaking fuel injector(s)
> 82 °C (180 °F) ignition retard inhibited IP Sensor fault (high fuel pressure)
Idle for 10 minutes – Bank 1 closed loop fuel EFT Sensor fault (high fuel temperature)
metering inhibited
MAF Sensor fault (high intake air flow)
– Canister purge inhibited
HO2 Sensor(s) (1/1, 1/2) harness wiring
– Maximum engine speed condition fault
reduced ECM receiving incorrect signal from one or
more of the following components:
ECT Sensor, MAF Sensor, IAT Sensor,
IP Sensor, EFT Sensor, TP Sensor
P0174 EMS Bank 2 combustion too lean Start engine and bring to 2 N ECM Default: — Engine misfire
OBD II normal operating temperature – Bank 2 catalyst warm-up Air intake leak between MAF Sensor and
> 82 °C (180 °F) ignition retard inhibited cylinder head
Idle for 10 minutes – Bank 2 closed loop fuel Fuel filter / system restriction
metering inhibited Fuel injector restriction
– Canister purge inhibited IP Sensor fault (low fuel pressure)
– Maximum engine speed Low fuel pump output
reduced HO2 Sensor(s) (2/1, 2/2)
harness wiring condition fault
EFT Sensor fault (low fuel temperature)
MAF Sensor fault (low intake air flow)
Exhaust leak (before catalyst)
ECM receiving incorrect signal from one or
more of the following components:
ECT Sensor, MAF Sensor, IAT Sensor,
IP Sensor, EFT Sensor, TP Sensor
P0175 EMS Bank 2 combustion too rich Start engine and bring to 2 N ECM Default: — Restricted air filter
OBD II normal operating temperature – Bank 2 catalyst warm-up Leaking fuel injector(s)
> 82 °C (180 °F) ignition retard inhibited IP Sensor fault (high fuel pressure)
Idle for 10 minutes – Bank 2 closed loop fuel EFT Sensor fault (high fuel temperature)
metering inhibited
MAF Sensor fault (high intake air flow)
– Canister purge inhibited
HO2 Sensor(s) (2/1, 2/2) harness wiring
– Maximum engine speed condition fault
reduced ECM receiving incorrect signal from one or
more of the following components:
ECT Sensor, MAF Sensor, IAT Sensor,
IP Sensor, EFT Sensor, TP Sensor
P0181 EMS EFT Sensor range / performance Engine OFF; coolant 2 N ECM Default: PI1 EFT Sensor disconnected
OBD II temperature <35 °C (95 °F) – Default value of 25 °C (77 °F) -050 EFT Sensor to ECM sensing circuit:
Start engine and drive until used high resistance, open circuit, short circuit to
normal engine operating ground short circuit to high voltage
temperature > 82 °C (180 °F) EFT Sensor to splice sensor ground circuit:
Drive for an additional 25 high resistance, open circuit
minutes EFT Sensor failure
P0182 EMS EFT Sensor circuit low voltage Ignition ON 10 seconds 2 N ECM Default: PI1 EFT Sensor to ECM sensing circuit:
OBD II (high temperature) – Default value of 25 °C (77 °F) -050 short circuit to ground
used EFT Sensor to splice sensor ground circuit:
short circuit
EFT Sensor failure
P0183 EMS EFT Sensor circuit high voltage Ignition ON 10 seconds 2 N ECM Default: PI1 EFT Sensor disconnected
OBD II (low temperature) – Default value of 25 °C (77 °F) -050 EFT Sensor to ECM sensing circuit:
used high resistance, open circuit, short circuit
to high voltage
EFT Sensor to splice sensor ground circuit:
high resistance, open circuit
EFT Sensor failure
P0191 EMS IP Sensor circuit range / Fuel level > 25% 2 N ECM Default: PI1 Fuel filter / system restriction
OBD II performance Idle engine 30 seconds – Default value of 3.80 BAR -073 Fuel system leak
Accelerate from stop through (55.11 psi) used Incorrect fuel pump output
complete engine rpm range; – Fuel pump feedback control IP Sensor to ECM sensing circuit:
coast to a stop inhibited high resistance, open circuit, short circuit
Drive the vehicle steadily to ground, short circuit to high voltage
between 48 – 97 km/h (30 – IP Sensor to splice sensor supply circuit:
60 mph) for 5 minutes; coast high resistance, open circuit
to a stop IP Sensor to splice sensor ground circuit:
Accelerate smoothly through high resistance, open circuit, short circuit
complete accelerator pedal to ground, short circuit to high voltage
travel; coast to a stop IP Sensor failure
Idle engine 30 seconds
P0192 EMS IP Sensor sensor circuit Ignition ON 10 seconds 2 N ECM Default: PI1 IP Sensor disconnected
OBD II low voltage (low pressure) – Default value of 3.80 BAR -073 IP Sensor to ECM sensing circuit:
(55.11 psi) used open circuit or short circuit to ground
– Fuel pump feedback control IP Sensor to splice sensor supply circuit:
inhibited high resistance open circuit
IP Sensor failure
P0193 EMS IP Sensor sensor circuit Ignition ON 10 seconds 2 N ECM Default: PI1 IP Sensor to ECM wiring (supply, sense): short
OBD II high voltage (high pressure) – Default value of 3.80 BAR -073 circuit to each other
(55.11 psi) used IP Sensor to ECM sense circuit:
short circuit to high voltage
– Fuel pump feedback control
inhibited IP Sensor to splice sensor ground circuit:
open circuit
IP Sensor failure
P0196 EMS EOT Sensor range / performance Engine OFF; coolant 2 N ECM Default: PI1 EOT Sensor to ECM sensing circuit;
OBD II temperature <35 °C (95 °F) – ECT substituted -078 high resistance when hot, intermittent
high resistance
Start engine and drive until
normal engine operating EOT Sensor failure
temperature > 82 °C (180 °F)
P0197 EMS EOT Sensor low voltage Ignition ON 10 seconds 2 N ECM Default: PI1 EOT Sensor to ECM sensing circuit:
OBD II (high temperature) – ECT substituted -078 short circuit to ground
EOT Sensor failure
P0198 EMS EOT Sensor high voltage Ignition ON 10 seconds 2 N ECM Default: PI1 EOT Sensor disconnected
OBD II (low temperature) – ECT substituted -078 EOT Sensor to ECM sensing circuit:
high resistance, open circuit, short circuit
to B+ voltage
EOT Sensor failure
P0201 EMS Fuel injector 1 circuit malfunction Start engine 2 A ECM Default: V6 Injector disconnected
OBD II Battery voltage > 12 volts – Bank 1 closed loop fuel PI1 Injector harness wiring:
metering inhibited -115 open circuit, short circuit
Idle for 2 minutes
– Bank 1 adaptive fuel metering V8 Injector failure
inhibited PI1
-120
– Bank 1 catalyst warm up
ignition retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0202 EMS Fuel injector 2 circuit malfunction Start engine 2 A ECM Default: V6 Injector disconnected
OBD II Battery voltage > 12 volts – Bank 2 closed loop fuel PI1 Injector harness wiring:
metering inhibited -120 open circuit, short circuit
Idle for 2 minutes
– Bank 2 adaptive fuel metering V8 Injector failure
inhibited PI1
-115
– Bank 2 catalyst warm up
ignition retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0203 EMS Fuel injector 3 circuit malfunction Start engine 2 A ECM Default: PI1 Injector disconnected
OBD II Battery voltage > 12 volts – Bank 1 closed loop fuel -114 Injector harness wiring:
metering inhibited open circuit, short circuit
Idle for 2 minutes
– Bank 1 adaptive fuel metering Injector failure
inhibited
– Bank 1 catalyst warm up
ignition retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0204 EMS Fuel injector 4 circuit malfunction Start engine 2 A ECM Default: PI1 Injector disconnected
OBD II Battery voltage > 12 volts – Bank 2 closed loop fuel -119 Injector harness wiring:
metering inhibited open circuit, short circuit
Idle for 2 minutes
– Bank 2 adaptive fuel metering Injector failure
inhibited
– Bank 2 catalyst warm up
ignition retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0205 EMS Fuel injector 5 circuit malfunction Start engine. 2 A ECM Default: PI1 Injector disconnected
OBD II Battery voltage > 12 volts – Bank 1 closed loop fuel -113 Injector harness wiring:
metering inhibited open circuit, short circuit
Idle for 2 minutes.
– Bank 1 adaptive fuel metering Injector failure
inhibited
– Bank 1 catalyst warm up
ignition retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0206 EMS Fuel injector 6 circuit malfunction Start engine. 2 A ECM Default: PI1 Injector disconnected
OBD II Battery voltage > 12 volts – Bank 2 closed loop fuel -118 Injector harness wiring:
metering inhibited open circuit, short circuit
Idle for 2 minutes.
– Bank 2 adaptive fuel metering Injector failure
inhibited
– Bank 2 catalyst warm up
ignition retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0207 V8 EMS Fuel injector 7 circuit malfunction Start engine. 2 A ECM Default: PI1 Injector disconnected
OBD II Battery voltage > 12 volts – Bank 1 closed loop fuel -117 Injector harness wiring:
metering inhibited open circuit, short circuit
Idle for 2 minutes.
– Bank 1 adaptive fuel metering Injector failure
inhibited
– Bank 1 catalyst warm up
ignition retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0208 V8 EMS Fuel injector 8 circuit malfunction Start engine. 2 A ECM Default: PI1 Injector disconnected
OBD II Battery voltage > 12 volts – Bank 2 closed loop fuel -112 Injector harness wiring:
metering inhibited open circuit, short circuit
Idle for 2 minutes.
– Bank 2 adaptive fuel metering Injector failure
inhibited
– Bank 2 catalyst warm up
ignition retard inhibited
– Canister purge inhibited
– Maximum engine speed
reduced
P0222 EMS TP Sensor sense circuit 2 (TP2) Battery voltage > 10 volts 2 R ECM Default: PI1 TP Sensor to ECM sensing circuit (TP2):
OBD II low voltage Ignition ON – Throttle motor and throttle -076 open circuit, short circuit to ground,
high resistance
Slowly press accelerator pedal motor relay disabled
TP Sensor failure
to the floor over a 5 second – Throttle valve opening set to
period default value
Slowly return the pedal to rest – Idle speed controlled by fuel
Repeat 3 times injection intervention
– Idle speed adaption inhibited
P0223 EMS TP Sensor sense circuit 2 (TP2) Battery voltage > 10 volts 2 R ECM Default: PI1 TP Sensor to ECM sensing circuit (TP2):
OBD II high voltage Ignition ON – Throttle motor and throttle -076 short circuit to high voltage
motor relay disabled TP Sensor failure
Slowly press accelerator pedal
to the floor over a 5 second – Throttle valve opening set to
period default value
Slowly return the pedal to rest – Idle speed controlled by fuel
Repeat 3 times injection intervention
– Idle speed adaption inhibited
P0300 EMS Random misfire detected Misfire monitor drive cycle – 1 or 2* N None — ECM to ignition coil primary circuit fault
OBD II page 6 (Cylinder misfire detected DTC also
flagged)
Fuel injector circuit fault(s)
(Injector DTCs also flagged)
Ignition coil failure
Spark plug failure / fouled / incorrect gap
Cylinder compression low
Fuel delivery pressure (low / high)
Fuel injector(s) restricted / leaking
Fuel injector(s) continuously open
Fuel contamination
*Refer to Misfire Note, page 6
Worn camshaft / broken valve spring(s)
P0301 EMS Misfire detected – cylinder 1 Misfire monitor drive cycle – 1 or 2* N None — Refer to P0300 Possible Causes
OBD II *Refer to Misfire Note, page 6 page 6
P0302 EMS Misfire detected – cylinder 2 Misfire monitor drive cycle – 1 or 2* N None — Refer to P0300 Possible Causes
OBD II *Refer to Misfire Note, page 6 page 6
P0303 EMS Misfire detected – cylinder 3 Misfire monitor drive cycle – 1 or 2* N None — Refer to P0300 Possible Causes
OBD II *Refer to Misfire Note, page 6 page 6
P0304 EMS Misfire detected – cylinder 4 Misfire monitor drive cycle – 1 or 2* N None — Refer to P0300 Possible Causes
OBD II *Refer to Misfire Note, page 6 page 6
P0305 EMS Misfire detected – cylinder 5 Misfire monitor drive cycle – 1 or 2* N None — Refer to P0300 Possible Causes
OBD II *Refer to Misfire Note, page 6 page 6
P0306 EMS Misfire detected – cylinder 6 Misfire monitor drive cycle – 1 or 2* N None — Refer to P0300 Possible Causes
OBD II *Refer to Misfire Note, page 6 page 6
P0307 V8 EMS Misfire detected – cylinder 7 Misfire monitor drive cycle – 1 or 2* N None — Refer to P0300 Possible Causes
OBD II *Refer to Misfire Note, page 6 page 6
P0308 V8 EMS Misfire detected – cylinder 8 Misfire monitor drive cycle – 1 or 2* N None — Refer to P0300 Possible Causes
OBD II *Refer to Misfire Note, page 6 page 6
P0327 EMS Bank 1 KS sense circuit out of Start engine 2 A ECM Default: PI1 Poor sensor contact with the cylinder block
OBD II range – low voltage Battery voltage > 12 volts – Maximum ignition retard -098 KS to ECM sense circuit short circuit to ground
Idle for 2 minutes – Maximum engine speed KS failure
reduced
P0328 EMS Bank 1 KS sense circuit out of Start engine 2 A ECM Default: PI1 Poor sensor contact with the cylinder block
OBD II range – high voltage Battery voltage > 12 volts – Maximum ignition retard -098 KS to ECM sense circuit: high resistance,
open circuit, short circuit to high voltage
Idle for 2 minutes – Maximum engine speed
reduced KS failure
P0332 EMS Bank 2 KS sense circuit out of Start engine 2 A ECM Default: PI1 Poor sensor contact with the cylinder block
OBD II range – low voltage Battery voltage > 12 volts – Maximum ignition retard -099 KS to ECM sense circuit short circuit to ground
Idle for 2 minutes – Maximum engine speed KS failure
reduced
P0333 EMS Bank 2 KS sense circuit out of Start engine 2 A ECM Default: PI1 Poor sensor contact with the cylinder block
OBD II range – high voltage Battery voltage > 12 volts – Maximum ignition retard -099 KS to ECM sense circuit: high resistance,
open circuit, short circuit to high voltage
Idle for 2 minutes – Maximum engine speed
reduced KS failure
P0335 EMS CKP Sensor circuit malfunction Start engine; increase engine 2 A ECM Default: PI1 CKP Sensor disconnected
OBD II speed to 1500 rpm and hold – Maximum engine speed -036 CKP Sensor gap incorrect / foreign matter on
for 30 seconds reduced -037 sensor face
Repeat 2 additional times – CMP Sensor 1 signal used for CKP Sensor sensing circuit:
Note: If CKP Sensor fault synchronization open circuit, short circuit to ground,
exists, engine will start after short circuit to high voltage
approximately 5 seconds of CKP Sensor failure
cranking as the ECM will
default to CMP Sensor 1
signal for synchronization.
P0336 EMS CKP Sensor circuit range / Start engine; momentarily 2 A ECM Default: PI1 CKP Sensor reluctor: foreign matter /
OBD II performance race the engine; stop engine – Maximum engine speed -036 damaged teeth
Repeat 2 additional times reduced -037 CKP Sensor sensing circuit:
intermittent open circuit, short circuit
Start engine; drive vehicle; to ground, short circuit to high voltage
select 2nd gear
CKP Sensor failure
Accelerate smoothly through
complete accelerator pedal
travel; coast to a stop
P0340 EMS CMP Sensor 1 circuit malfunction Start engine; momentarily 2 N None PI1 CMP Sensor disconnected
OBD II – bank 1 race the engine; stop engine -094 CMP Sensor gap incorrect / foreign matter on
Repeat 2 additional times -095 sensor face
Idle engine 1 minute CMP Sensor sensing circuit:
open circuit, short circuit to ground,
short circuit to high voltage
CMP Sensor 1 failure
P0341 EMS CMP Sensor 1 circuit range / Start engine; momentarily 2 N None PI1 CMP Sensor disconnected
OBD II performance – bank 1 race the engine; stop engine -094 CMP Sensor gap incorrect / foreign matter on
Repeat 2 additional times -095 sensor face
Idle engine 1 minute CMP Sensor sensing circuit:
open circuit, short circuit to ground,
short circuit to high voltage
CMP Sensor 1 failure
P0345* EMS CMP Sensor 2 circuit malfunction Start engine; momentarily 2 N None PI1 CMP Sensor disconnected
OBD II – bank 2 race the engine; stop engine -068 CMP Sensor gap incorrect / foreign matter on
Repeat 2 additional times -069 sensor face
Idle engine 1 minute CMP Sensor sensing circuit:
open circuit, short circuit to ground,
* P0345 Early production short circuit to high voltage
vehicles; P1340 later production
vehicles CMP Sensor 2 failure
P0346* EMS CMP Sensor 2 circuit range / Start engine; momentarily 2 N None PI1 CMP Sensor disconnected
OBD II performance – bank 2 race the engine; stop engine -068 CMP Sensor gap incorrect / foreign matter on
Repeat 2 additional times -069 sensor face
Idle engine 1 minute CMP Sensor sensing circuit:
open circuit, short circuit to ground,
* P0346 Early production short circuit to high voltage
vehicles; P1341 later production
vehicles CMP Sensor 2 failure
P0351 EMS Ignition module primary circuit Start engine 2 A ECM Default: PI1 ECM to ignition module primary circuit:
OBD II malfunction – cylinder 1 Battery voltage > 12 volts – Bank 1 closed loop fuel -087 open circuit, short circuit to ground,
high resistance
Idle for 2 minutes metering inhibited
Ignition module ground circuit:
– Bank 1 sub feedback control open circuit, high resistance
inhibited
Ignition module / coil failure
– Bank 1 adaptive fuel metering
inhibited
– Maximum engine speed
reduced
– Fuel injection cut off
(cylinder 1)
P0352 EMS Ignition module primary circuit Start engine 2 A ECM Default: PI1 ECM to ignition module primary circuit:
OBD II malfunction – cylinder 2 Battery voltage > 12 volts – Bank 2 closed loop fuel -061 open circuit, short circuit to ground,
high resistance
Idle for 2 minutes metering inhibited
Ignition module ground circuit:
– Bank 2 sub feedback control open circuit, high resistance
inhibited
Ignition module / coil failure
– Bank 2 adaptive fuel metering
inhibited
– Maximum engine speed
reduced
– Fuel injection cut off
(cylinder 2)
P0353 EMS Ignition module primary circuit Start engine 2 A ECM Default: PI1 ECM to ignition module primary circuit:
OBD II malfunction – cylinder 3 Battery voltage > 12 volts – Bank 1 closed loop fuel -088 open circuit, short circuit to ground,
high resistance
Idle for 2 minutes metering inhibited
Ignition module ground circuit:
– Bank 1 sub feedback control open circuit, high resistance
inhibited
Ignition module / coil failure
– Bank 1 adaptive fuel metering
inhibited
– Maximum engine speed
reduced
– Fuel injection cut off
(cylinder 3)
P0354 EMS Ignition module primary circuit Start engine 2 A ECM Default: PI1 ECM to ignition module primary circuit:
OBD II malfunction – cylinder 4 Battery voltage > 12 volts – Bank 2 closed loop fuel -062 open circuit, short circuit to ground,
high resistance
Idle for 2 minutes metering inhibited
Ignition module ground circuit:
– Bank 2 sub feedback control open circuit, high resistance
inhibited
Ignition module / coil failure
– Bank 2 adaptive fuel metering
inhibited
– Maximum engine speed
reduced
– Fuel injection cut off
(cylinder 4)
P0355 EMS Ignition module primary circuit Start engine 2 A ECM Default: PI1 ECM to ignition module primary circuit:
OBD II malfunction – cylinder 5 Battery voltage > 12 volts – Bank 1 closed loop fuel -089 open circuit, short circuit to ground,
high resistance
Idle for 2 minutes metering inhibited
Ignition module ground circuit:
– Bank 1 sub feedback control open circuit, high resistance
inhibited
Ignition module / coil failure
– Bank 1 adaptive fuel metering
inhibited
– Maximum engine speed
reduced
– Fuel injection cut off
(cylinder 5)
P0356 EMS Ignition module primary circuit Start engine 2 A ECM Default: PI1 ECM to ignition module primary circuit:
OBD II malfunction – cylinder 6 Battery voltage > 12 volts – Bank 2 closed loop fuel -063 open circuit, short circuit to ground,
high resistance
Idle for 2 minutes metering inhibited
Ignition module ground circuit:
– Bank 2 sub feedback control open circuit, high resistance
inhibited
Ignition module / coil failure
– Bank 2 adaptive fuel metering
inhibited
– Maximum engine speed
reduced
– Fuel injection cut off
(cylinder 6)
P0357 V8 EMS Ignition module primary circuit Start engine 2 A ECM Default: PI1 ECM to ignition module primary circuit:
OBD II malfunction – cylinder 7 Battery voltage > 12 volts ECM Default: -090 open circuit, short circuit to ground,
high resistance
Idle for 2 minutes – Bank 1 closed loop fuel Ignition module ground circuit:
metering inhibited open circuit, high resistance
– Bank 1 sub feedback control Ignition module / coil failure
inhibited
– Bank 1 adaptive fuel metering
inhibited
– Maximum engine speed
reduced
– Fuel injection cut off
(cylinder 7)
P0358 V8 EMS Ignition module primary circuit Start engine 2 A ECM Default: PI1 ECM to ignition module primary circuit:
OBD II malfunction – cylinder 8 Battery voltage > 12 volts – Bank 2 closed loop fuel -064 open circuit, short circuit to ground,
high resistance
Idle for 2 minutes metering inhibited
Ignition module ground circuit:
– Bank 2 sub feedback control open circuit, high resistance
inhibited
Ignition module / coil failure
– Bank 2 adaptive fuel metering
inhibited
– Maximum engine speed
reduced
– Fuel injection cut off
(cylinder 8)
P0400 V8 EMS EGR flow malfunction EGR Monitor drive cycle – 2 N None — EGR valve incorrectly fitted or loose
OBD II page 8 EGR pipe blocked
EGR valve stuck open / closed, blocked
EGR valve failure
P0405 V8 EMS EGR valve drive circuits low voltage Ignition ON 10 seconds 2 N None IP1 EGR valve power supply circuit open circuit
OBD II -057 EGR valve to ECM drive circuit pair
-058 (EGR valve pins 1/4, 6/3):
-059 open circuit, high resistance
-060
EGR valve failure (stepper motor open circuit)
P0406 V8 EMS EGR valve drive circuits high Ignition ON 10 seconds 2 N None IP1 EGR valve to ECM drive circuit pair
voltage -057 (EGR valve pins 1/4, 6/3):
OBD II short circuit to ground or high voltage
-058
-059 EGR valve failure (stepper motor short circuit)
-600
P0420 EMS Catalytic converter system Catalyst efficiency monitor 2 N None — HO2 Sensor disconnected
OBD II efficiency below threshold – drive cycle – page 6 HO2 Sensor to ECM wiring fault
bank 1
HO2 Sensor heater to ECM wiring fault
HO2 Sensor heater failure
Upstream HO2 Sensor failure
Downstream HO2 Sensor failure
Catalyst failure
P0430 EMS Catalytic converter system Catalyst efficiency monitor 2 N None — HO2 Sensor disconnected
OBD II efficiency below threshold – drive cycle – page 6 HO2 Sensor to ECM wiring fault
bank 2
HO2 Sensor heater to ECM wiring fault
HO2 Sensor heater failure
Upstream HO2 Sensor failure
Downstream HO2 Sensor failure
Catalyst failure
P0442 EMS EVAP system leak detected – Evaporative system monitor 2 N ECM Default: — Fuel cap seal defective
OBD II small (0.040 in.) drive cycle – page 7 – Canister purge inhibited EVAP system leak (canister damage,
pipework damage)
– Adaptive fuel metering
inhibited EVAP Canister purge valve to ECM drive
circuit: open circuit, short circuit, high
resistance
EVAP Canister purge valve power supply
circuit: open circuit, short circuit
EVAP Canister purge valve to engine purge
pipe: restricted, leaking, disconnected
EVAP Canister purge valve operating vacuum
hose leak / restriction
EVAP Canister purge valve failure
Fuel tank leak
P0443 EMS EVAP canister purge valve circuit Evaporative system monitor 2 N ECM Default: PI1 EVAP Canister purge valve to ECM drive
OBD II malfunction drive cycle – page 7 – Canister purge inhibited -066 circuit: open circuit, short circuit, high
resistance
– Adaptive fuel metering EVAP Canister purge valve power supply
inhibited circuit: open circuit, short circuit
EVAP Canister purge valve operating vacuum
hose leak / restriction
EVAP Canister purge valve failure
P0444 EMS EVAP canister purge valve circuit Evaporative system monitor 2 N ECM Default: PI1 EVAP Canister purge valve disconnected
OBD II open circuit drive cycle – page 7 – Canister purge inhibited -066 EVAP Canister purge valve to ECM drive
– Adaptive fuel metering circuit: open circuit, high resistance
inhibited EVAP Canister purge valve failure
P0445 EMS EVAP canister purge valve circuit Evaporative system monitor 2 N ECM Default: PI1 EVAP Canister purge valve to ECM drive
OBD II short circuit drive cycle – page 7 – Canister purge inhibited -066 circuit: short circuit to ground
EVAP Canister purge valve failure
– Adaptive fuel metering
inhibited
P0446 EMS EVAP canister close valve circuit Evaporative system monitor 2 N ECM Default: PI1 EVAP canister close valve power supply
OBD II malfunction drive cycle – page 7 – Canister purge inhibited -067 circuit: open circuit, short circuit
EVAP canister close valve to ECM drive circuit:
– Adaptive fuel metering open circuit, high resistance, short circuit to
inhibited B+ voltage
EVAP canister close valve failure
P0447 EMS EVAP canister close valve circuit Ignition ON 10 seconds 2 N ECM Default: PI1 EVAP canister close valve power supply
OBD II open circuit – Canister purge inhibited -067 circuit: open circuit, short circuit
EVAP canister close valve to ECM drive circuit:
– Adaptive fuel metering open circuit, high resistance, short circuit to
inhibited B+ voltage
EVAP canister close valve failure
P0448 EMS EVAP canister close valve circuit Ignition ON 10 seconds 2 N ECM Default: PI1 EVAP canister close valve to ECM drive circuit:
OBD II short circuit – Canister purge inhibited -067 short to ground
EVAP canister close valve failure
– Adaptive fuel metering
inhibited
P0450 EMS FTP Sensor circuit malfunction Evaporative system monitor 2 N None PI1 FTP Sensor disconnected
OBD II drive cycle – page 7 -104 FTP Sensor to ECM sense circuit:
open circuit, short circuit to ground,
short circuit to B+ voltage
FTP Sensor to splice sensor supply circuit:
open circuit, high resistance
FTP Sensor to splice ground circuit:
open circuit, high resistance
FTP Sensor failure
P0452 EMS FTP Sensor circuit low voltage Ignition ON 10 seconds 2 N None PI1 FTP Sensor disconnected
OBD II (low pressure) -104 FTP Sensor to ECM sense circuit:
open circuit, short circuit to ground
FTP Sensor to splice sensor supply circuit:
open circuit, high resistance
FTP Sensor failure
P0453 EMS FTP Sensor circuit high voltage Ignition ON 10 seconds 2 N None PI1 FTP Sensor to splice sensor ground circuit:
OBD II (high pressure) -104 open circuit, high resistance
FTP Sensor to ECM sense circuit:
short circuit to high voltage
FTP Sensor failure
P0455 EMS EVAP system leak detected – Evaporative system monitor 2 N ECM Default: — Fuel cap off
OBD II large drive cycle – page 7 – Canister purge inhibited Fuel cap seal defective
– Adaptive fuel metering EVAP system leak
inhibited (canister damage, pipework damage)
EVAP Canister purge valve to ECM drive
circuit: open circuit, short circuit,
high resistance
EVAP Canister purge valve power supply
circuit: open circuit, short circuit
EVAP Canister purge valve to engine purge
pipe: restricted, leaking, disconnected
EVAP Canister purge valve operating vacuum
hose leak / restriction
EVAP Canister purge valve failure
Fuel tank leak
P0456 EMS EVAP system leak detected – Evaporative system monitor 2 N ECM Default: — Fuel cap seal defective
OBD II very small (0.020 in.) drive cycle – page 7 – Canister purge inhibited EVAP system leak
(canister damage, pipework damage)
– Adaptive fuel metering
inhibited EVAP Canister purge valve to ECM drive
circuit: open circuit, short circuit,
high resistance
EVAP Canister purge valve power supply
circuit: open circuit, short circuit
EVAP Canister purge valve to engine purge
pipe: restricted, leaking
EVAP Canister purge valve operating vacuum
hose leak / restriction
EVAP Canister purge valve failure
Fuel tank leak
P0460 EMS Fuel level sensor(s) circuit range / Fuel tank empty 2 N None — Fuel level sensor to Rear Electronic Control
OBD II performance Fill in stages: 1/4, 1/2, 3/4, full Module circuit(s): intermittent short circuit,
open circuit, high resistance
Check fuel gauge reading at Fuel level sensor failure
each stage
Rear Electronic Control Module fault (incorrect
fuel level data)
P0480 EMS Radiator cooling fan module drive Start engine N N ECM Default: PI1 ECM to radiator cooling fan module drive
OBD II circuit malfunction Battery voltage > 12 volts – With ignition ON, fan operates -051 circuit: short circuit, open circuit,
high resistance
Idle for 2 minutes at maximum speed
Radiator cooling fan fault
Radiator cooling fan module fault
P0506 EMS Idle RPM lower than expected Start engine and drive until 2 N None — Air intake restriction
OBD II normal engine operating Accessory drive overload
temperature > 82 °C (180 °F) (defective / seized component)
Stop vehicle and idle 30 Throttle valve stuck closed
seconds
Throttle body failure
Drive vehicle for 2 minutes
Stop vehicle and idle 30
seconds
Repeat drive / idle two
additional times
P0507 EMS Idle RPM higher than expected Start engine and drive until 2 N None — Intake air leak between MAF sensor and
OBD II normal engine operating throttle
temperature > 82 °C (180 °F) Intake air leak between throttle and engine
Stop vehicle and idle 30 Engine crankcase breather leak
seconds
Throttle valve stuck open
Drive vehicle for 2 minutes
Throttle body failure
Stop vehicle and idle 30
seconds
Repeat drive / idle two
additional times
P0532 EMS Air conditioning pressure sensor Start engine N N ECM Default: PI1 Air conditioning pressure sensor disconnected
JAG circuit low voltage (high pressure) Use WDS to monitor air – Air conditioning compressor -121 Air conditioning pressure sensor to ECM
conditioning pressure sensor clutch inhibited sense circuit: open circuit, short circuit to
signal voltage ground
Set climate control to a low Air conditioning pressure sensor to splice
temperature; operate for 2 sensor supply circuit: open circuit,
minutes high resistance
Switch off climate control; Air conditioning pressure sensor failure
wait 2 minutes
P0533 EMS Air conditioning pressure sensor Start engine N N ECM Default: PI1 Air conditioning pressure sensor to splice
JAG circuit high voltage (low pressure) Use WDS to monitor air – Air conditioning compressor -121 sensor ground circuit: open circuit,
high resistance
conditioning pressure sensor clutch inhibited
signal voltage Air conditioning pressure sensor to ECM
sense circuit: short circuit to high voltage
Set climate control to a low
temperature; operate for 2 Air conditioning pressure sensor failure
minutes
Switch off climate control;
wait 2 minutes
P0560 EMS Battery power supply voltage Engine temperature cool 2 N None PI1 ECM battery power supply open circuit,
OBD II malfunction (cooling fans not running) -022 high resistance
Remove ignition key for 20
seconds (cooling fans not
running)
Ignition key in, position II for 5
seconds (do not start)
Repeat cycle two additional
times
P0566 EMS Speed control CANCEL switch Ignition ON 45 seconds N A ECM Default: PI1 Speed control switches internal steering
JAG ON fault – Speed control inhibited -047 wheel circuit: short circuit to ground
Steering wheel cassette reel:
short circuit to ground
Cassette reel to ECM circuit:
short circuit to ground
CANCEL switch failure (stuck ON)
P0567 EMS Speed control RESUME switch Ignition ON 45 seconds N A ECM Default: PI1 Speed control switches internal steering
JAG ON fault – Speed control inhibited -047 wheel circuit: short circuit to ground
Steering wheel cassette reel:
short circuit to ground
Cassette reel to ECM circuit:
short circuit to ground
RESUME switch failure (stuck ON)
P0568 EMS Speed control input signal low / Ignition ON 45 seconds N A ECM Default: PI1 Speed control switches internal steering
JAG high resistance – Speed control inhibited -047 wheel circuit: open circuit; high resistance
Steering wheel cassette reel open circuit,
high resistance
Cassette reel to ECM circuit:
open circuit, high resistance
P0569 EMS Speed control SET / - switch ON Ignition ON for more than 5 N A ECM Default: PI1 Speed control switches internal steering
JAG fault minutes – Speed control inhibited -047 wheel circuit: short circuit to ground
Steering wheel cassette reel:
short circuit to ground
Cassette reel to ECM circuit:
short circuit to ground
SET / - switch failure
P0570 EMS Speed control SET / + switch ON Ignition ON for more than 5 N A ECM Default: PI1 Speed control switches internal steering
JAG fault minutes – Speed control inhibited -047 wheel circuit: short circuit to ground
Steering wheel cassette reel:
short circuit to ground
Cassette reel to ECM circuit:
short circuit to ground
SET / + switch failure
P0603 EMS ECM Keep alive memory error Engine temperature cool 2 N None — ECM Failure
OBD II (cooling fans not running)
Remove ignition key for 20
seconds (cooling fans not
running)
Ignition key in, position II for 5
seconds (do not start)
Repeat cycle two additional
times.
P0605 TRANS TCM Self test error Ignition ON 10 seconds 2 A None — TCM / Control valve failure
OBD II
P0606 TRANS TCM “Watch dog” circuit Ignition ON 10 seconds N A TCM Default: — TCM / Control valve failure
OBD II malfunction – Mechanical limp home mode
P0610 TRANS TCM Configuration error Ignition ON 10 seconds N A None — Reconfigure TCM using WDS
JAG
P0617 EMS Starter relay drive circuit high Ignition ON 2 N None PI1 Starter relay drive circuit:
OBD II voltage / starter relay request on Battery voltage > 12 volts -041 short circuit to high voltage
(ignition switch position III Starter relay failure
START) Automatic – P or N selected;
manual – clutch fully pressed
Crank engine for more than 2
seconds
P0641 TRANS Sensor supply voltage circuit Ignition ON 10 seconds 2 A TCM Default: — TCM / Control valve failure
OBD II malfunction – Mechanical limp home mode
P0646 EMS A/C Compressor clutch relay drive Start engine 2 N None PI1 A/C Compressor clutch relay drive circuit:
OBD II circuit low voltage (CAN A/C Climate control system OFF -034 open circuit, high resistance
compressor clutch request OFF) A/C Compressor clutch relay failure
Idle for 10 seconds
P0647 EMS A/C Compressor clutch relay drive Start engine 2 N None PI1 A/C Compressor clutch relay drive circuit:
OBD II circuit high voltage (CAN A/C Climate control system ON – -034 short circuit to high voltage
compressor clutch request ON) full cooling A/C Compressor clutch relay failure
Idle for 2 minutes
P0651 TRANS Pressure regulator and shift Ignition ON 10 seconds 2 A TCM Default: — TCM / Control valve failure
OBD II solenoid supply circuit – Mechanical limp home mode
malfunction
P0666 TRANS Substrate temperature sensor Drive the vehicle steadily N N None — TCM / Control valve failure
JAG circuit malfunction between 48 – 97 km/h (30 –
60 mph) for 5 minutes. Coast
to a stop.
P0701 TRANS TCM control errors Drive vehicle from stop to 113 2 A TCM Default: — TCM / Control valve failure
OBD II km/h (70 mph). Coast to a – Mechanical limp home mode
stop.
P0702 TRANS TCM Battery power supply low Ignition ON 10 seconds 2 A TCM Default: GB2 Battery power supply fuse failure
OBD II voltage (short time) – Mechanical limp home mode -14 Battery power supply: intermittent
open circuit
P0705 TRANS Gear position switch circuit Switch ignition ON. Move the 2 A TCM Default: — TCM / Control valve failure
OBD II malfunction gear selector slowly from P to – Mechanical limp home mode
the 2 position, then back to P
P0706 TRANS J Gate selector position Switch ignition ON. Move the N A TCM Default: — TCM / J Gate Module CAN fault
JAG plausibility fault gear selector slowly from P to – Shift strategy fixed J Gate Module failure
the 2 position, then back to P
– J Gate “manual” function TCM / Control valve failure
disabled
P0709 TRANS J Gate selector Intermediate Switch ignition ON. Move the N A TCM Default: — J Gate Module failure
JAG position fault gear selector slowly from P to – Shift strategy fixed
the 2 position, then back to P
– J Gate “manual” function
disabled
P0710 TRANS Transmission fluid temperature Drive the vehicle steadily N N None — TCM / Control valve failure
JAG sensor circuit malfunction between 48 – 97 km/h (30 –
60 mph) for 5 minutes. Coast
to a stop.
P0711 TRANS Engine fluid temperature range Drive the vehicle steadily N N None — TCM / ECM CAN Fault
JAG fault between 48 – 97 km/h (30 – TCM / Control valve failure
60 mph) for 5 minutes. Coast
to a stop.
P0715 TRANS Turbine speed sensor circuit Drive the vehicle steadily 2 A TCM Default: — TCM / Control valve failure
OBD II failure between 48 – 97 km/h (30 – – Mechanical limp home mode
60 mph) for 5 minutes. Coast
to a stop.
P0720 TRANS Output speed sensor circuit Drive vehicle from stop to 113 N N TCM Default: — TCM / Control valve failure
JAG failure km/h (70 mph). Coast to a – Mechanical limp home mode
stop.
– Substitute DSC vehicle speed
for transmission output speed
P0721 TRANS Output speed sensor signal Drive vehicle from stop to 113 2 A TCM Default: — Transmission mechanical failure
OBD II gradient fault km/h (70 mph). Coast to a – Mechanical limp home mode TCM / Control valve failure
stop.
– Substitute DSC vehicle speed
for transmission output speed
P0725 TRANS Engine over-speed range fault Using full acceleration, drive 2 A TCM Default: — TCM / ECM CAN Fault
OBD II vehicle from stop to 113 km/h – Mechanical limp home mode
(70 mph). Coast to a stop.
P0729 TRANS Sixth gear ratio fault Drive vehicle from stop to 113 2 A TCM Default: — Transmission mechanical failure
OBD II km/h (70 mph). Ensure that – Mechanical limp home mode
Sixth gear is engaged by
moving the gear selector to
the 5 position and observing
that the transmission down
shifts. Coast to a stop.
P0730 TRANS Gear ratio fault Drive vehicle from stop to 113 N N None — Transmission mechanical failure
JAG km/h (70 mph). Ensure that
Sixth gear is engaged by
moving the gear selector to
the 5 position and observing
that the transmission down
shifts. Coast to a stop
P0731 TRANS First gear ratio fault Start vehicle and select gear 2 A TCM Default: — Transmission mechanical failure
OBD II position 2. Accelerate hard – Mechanical limp home mode
until the engine speed
reaches 4500 rpm, after the
transmission has shifted to
second gear. Stop the
vehicle.
Repeat two additional times
P0732 TRANS Second gear ratio fault Start vehicle and select gear 2 A TCM Default: — Transmission mechanical failure
OBD II position 2. Accelerate the – Mechanical limp home mode
vehicle until second gear is
engaged. Drive the vehicle for
5 minutes in second gear.
Vary the vehicle speed and
acceleration rate.
P0733 TRANS Third gear ratio fault Start vehicle and select gear 2 A TCM Default: — Transmission mechanical failure
OBD II position 3. Accelerate the – Mechanical limp home mode
vehicle until third gear is
engaged. Drive the vehicle for
5 minutes in third gear. Vary
the vehicle speed and
acceleration rate.
P0734 TRANS Fourth gear ratio fault Start vehicle and select gear 2 A TCM Default: — Transmission mechanical failure
OBD II position 4. Accelerate the – Mechanical limp home mode TCM / Control valve failure
vehicle until fourth gear is
engaged. Drive the vehicle for
5 minutes in fourth gear. Vary
the vehicle speed and
acceleration rate.
P0735 TRANS Fifth gear ratio fault Start vehicle and select gear 2 A TCM Default: — Transmission mechanical failure
OBD II position 5. Accelerate the – Mechanical limp home mode TCM / Control valve failure
vehicle until fifth gear is
engaged. Drive the vehicle for
5 minutes in fifth gear. Vary
the vehicle speed and
acceleration rate.
P0736 TRANS Reverse gear ratio fault Start vehicle and select 2 A TCM Default: — Transmission mechanical failure
OBD II REVERSE gear. Accelerate – Mechanical limp home mode
the vehicle at different rates
for 1 minute.
P0740 TRANS Torque converter clutch pressure Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II regulator solenoid circuit (70 mph), then reduce the – Mechanical limp home mode
malfunction throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0741 TRANS Torque converter clutch pressure Drive the vehicle at 113 km/h N N TCM Default: — TCM / Control valve failure
JAG regulator solenoid stuck open (70 mph), then reduce the – Deactivate torque converter Transmission mechanical failure
throttle angle until the torque clutch pressure regulator; lock
convertor locks. Ensure that up clutch disabled
the torque convertor remains
locked for at least 1 minute.
P0743 TRANS Torque converter clutch pressure Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II regulator solenoid circuit (70 mph), then reduce the – Mechanical limp home mode
plausibility error throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0750 TRANS Pressure regulator solenoid 1 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit malfunction (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0753 TRANS Pressure regulator solenoid 1 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit plausibility error (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0755 TRANS Pressure regulator solenoid 2 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit malfunction (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0758 TRANS Pressure regulator solenoid 2 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit plausibility error (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0760 TRANS Pressure regulator solenoid 3 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit malfunction (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0763 TRANS Pressure regulator solenoid 3 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit plausibility error (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0765 TRANS Pressure regulator solenoid 4 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit malfunction (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0768 TRANS Pressure regulator solenoid 4 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit plausibility error (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0770 TRANS Pressure regulator solenoid 5 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit malfunction (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0773 TRANS Pressure regulator solenoid 5 Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II circuit plausibility error (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0780 TRANS Gear load fault Drive the vehicle at 113 km/h N N None — Transmission mechanical failure
JAG (70 mph), then reduce the
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0781 TRANS 1–2 / 2–1 Gear load fault Drive the vehicle at 113 km/h 2 A TCM Default: — Transmission mechanical failure
OBD II (70 mph), then reduce the – Electronic limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0782 TRANS 2–3 / 3–2 Gear load fault Drive the vehicle at 113 km/h 2 A TCM Default: — Transmission mechanical failure
OBD II (70 mph), then reduce the – Electronic limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0783 TRANS 3–4 / 4–3 Gear load fault Drive the vehicle at 113 km/h 2 A TCM Default: — Transmission mechanical failure
OBD II (70 mph), then reduce the – Electronic limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0784 TRANS 4–5 / 5–4 Gear load fault Drive the vehicle at 113 km/h 2 A TCM Default: — Transmission mechanical failure
OBD II (70 mph), then reduce the – Electronic limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0787 TRANS Shift solenoid circuit malfunction Ignition ON 10 seconds 2 A TCM Default: — TCM / Control valve failure
OBD II – Mechanical limp home mode
P0788 TRANS Shift solenoid circuit plausibility Drive the vehicle at 113 km/h 2 A TCM Default: — TCM / Control valve failure
OBD II error (70 mph), then reduce the – Mechanical limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0825 TRANS J Gate positions R, D plausibility Ignition ON. Slowly move gear N A None — J Gate incorrectly adjusted
JAG error selector from Park to Drive, J Gate Module failure
then back to Park.
P0829 TRANS 5–6 Gear load fault Drive the vehicle at 113 km/h 2 A TCM Default: — Transmission mechanical failure
OBD II (70 mph), then reduce the – Electronic limp home mode
throttle angle until the torque
convertor locks. Ensure that
the torque convertor remains
locked for at least 1 minute.
P0831 TRANS Clutch cancel switch low voltage Drive vehicle 60 – 100 km/h 2 N None PI1 Clutch cancel switch supply circuit:
(ECM*) (switch normally closed) (37 – 62 mph); -033 open circuit
V6: 1800 – 3000 rpm; engine Clutch cancel switch to ECM circuit:
OBD II open circuit, high resistance
load > 0.60 g/rpm
V8:1800 – 2500 rpm; engine Clutch cancel switch failure
* Manual transmission input to
ECM load > 0.40 g/rpm
Continue for 30 seconds
P0832 TRANS Clutch cancel switch high voltage Drive vehicle > 10 km/h (6 2 N None PI1 Clutch cancel switch to ECM circuit:
(ECM*) (switch normally closed) mph); shift from 1st to 2nd; -033 short circuit to high voltage
stop vehicle Clutch cancel switch failure
OBD II
* Manual transmission input to Repeat 6 times
ECM
P0834 TRANS Clutch pedal safety switch low Drive vehicle > 10 km/h (6 N N None PI1 Clutch pedal safety switch supply circuit:
(ECM*) voltage (switch normally open) mph); shift from 1st to 2nd; -031 open circuit
* Manual transmission input to stop vehicle Clutch pedal safety switch to ECM circuit:
JAG ECM open circuit, high resistance
Repeat 30 times
Clutch pedal safety switch failure
P0835 TRANS Clutch pedal safety switch high Drive vehicle 60 – 100 km/h N N None PI1 Clutch pedal safety switch to ECM circuit:
(ECM*) voltage (switch normally open) (37 – 62 mph); -031 short circuit to high voltage
* Manual transmission input to V6: 1800 – 3000 rpm; engine Clutch pedal safety switch failure
JAG ECM load > 0.60 g/rpm
V8: 1800 – 2500 rpm; engine
load > 0.40 g/rpm
Continue for 30 seconds
P0860 TRANS J Gate CAN network malfunction Ignition ON 10 seconds N A ECM Default: PI1 CAN open circuit fault
(ECM*) – Speed control inhibited -123 CAN short circuit fault
-124
JAG – Maximum throttle opening for J Gate failure
N range inhibited
– Throttle opening limited to
30%
– Maximum engine speed
* J Gate / CAN monitored by ECM reduced
P1000 EMS System (OBD) check not System Readiness Test N N None — Refer to page 3
JAG complete since last memory clear
P1104 EMS MAF Sensor ground malfunction Ignition ON 10 seconds 2 A ECM Default: PI1 MAF Sensor to ECM sensor ground circuit
OBD II – Calculated default air mass -045 open circuit, short circuit to high voltage,
-046 high resistance
used
MAF Sensor to ECM sensing circuit:
– Adaptive fuel metering open circuit
inhibited
MAF Sensor failure
– Sub feedback control inhibited
– Catalyst warm up ignition
retard inhibited
– EGR inhibited (V8)
– Canister purge inhibited
– Maximum engine speed
reduced
P1107 EMS MAP Sensor sense circuit Ignition ON 10 seconds 2 N ECM Default: PI1 MAP Sensor to ECM sense circuit:
OBD II low voltage – Default value of 1.013 BAR -127 open circuit, short circuit to ground
(29.92 in hg) used MAP Sensor sensor supply circuit (to splice):
open circuit
MAP Sensor failure
P1108 EMS MAP Sensor sense circuit Ignition ON 10 seconds 2 N ECM Default: PI1 MAP Sensor sensor ground circuit (to splice):
OBD II high voltage – Default value of 1.013 BAR -127 open circuit
(29.92 in hg) used MAP Sensor to ECM sense circuit:
short circuit to high voltage
MAP Sensor failure
P1111 EMS System (OBD) checks complete System Readiness Test N N None — Refer to page 3
JAG since last memory clear
P1122 EMS APP Sensor sense circuit low Battery voltage > 10 volts 2 R ECM Default: PI1 APP Sensor to ECM sense circuit (APP1):
OBD II voltage – APP1 Ignition ON – APP angle default value used -102 open circuit, short circuit to ground,
high resistance
Slowly press accelerator pedal – Speed control inhibited APP Sensor sensor supply circuit:
to the floor over a 5 second – APP adaptions (wear, open circuit, high resistance
period. variance) inhibited APP Sensor failure
Slowly return the pedal to rest
Repeat 3 times
P1123 EMS APP Sensor sense circuit high Battery voltage > 10 volts 2 R ECM Default: PI1 APP Sensor sensor to ECM sense circuit(s)
OBD II voltage – APP1 Ignition PI1ON – APP angle default value used -102 (APP1 or APP2): short circuit to high voltage
-103 APP Sensor sensor ground circuit(s):
Slowly press accelerator pedal – Speed control inhibited open circuit
Note: This DTC could be flagged to the floor over a 5 second – APP adaptions (wear,
by both sensor element sensing period APP Sensor failure
variance) inhibited
circuit having faults. Slowly return the pedal to rest
Repeat 3 times
P1146 V6 EMS Generator “CHARGE” circuit low Battery voltage > 12 volts 2 C None PI1 Generator to ECM “CHARGE” circuit:
OBD II voltage / request high Switch OFF all electrical -053 open circuit, high resistance
consumers Generator regulator failure
Start engine; idle for 16
minutes with all electrical
consumers switched OFF
P1215 EMS APP Sensor sense circuit low Battery voltage > 10 volts 2 R ECM Default: PI1 APP Sensor to ECM sense circuit (APP2):
OBD II voltage – APP2 Ignition ON – APP angle default value used -103 open circuit, short circuit to ground,
high resistance
Slowly press accelerator pedal – Speed control inhibited APP Sensor sensor supply circuit (to splice):
to the floor over a 5 second – APP adaptions (wear, open circuit, high resistance
period variance) inhibited APP Sensor failure
Slowly return the pedal to rest
Repeat 3 times
P1216 EMS APP Sensor sense circuit high Battery voltage > 10 volts 2 R ECM Default: PI1 APP Sensor sensor to ECM sense circuit(s)
OBD II voltage – APP2 Ignition ON – APP angle default value used -102 (APP2 or APP1): short circuit to high voltage
-103 APP Sensor sensor ground circuit(s) (to
Slowly press accelerator pedal – Speed control inhibited splice): open circuit
Note: This DTC could be flagged to the floor over a 5 second – APP adaptions (wear,
by both sensor element sensing period APP Sensor failure
variance) inhibited
circuit having faults. Slowly return the pedal to rest
Repeat 3 times
P1224 EMS Throttle control position error Battery voltage > 10 volts 2 R ECM Default: PI1 Throttle motor failure
OBD II Ignition ON – Engine shut down -080 Throttle body failure
-106
Slowly press accelerator pedal – Speed control disabled -052
to the floor over a 5 second -134
period
Slowly return the pedal to rest
Repeat 3 times
P1229 EMS Throttle motor control circuit Battery voltage > 10 volts 2 R ECM Default: PI1 Throttle motor disconnected
OBD II malfunction Ignition ON – Throttle motor and throttle -080 Throttle motor to ECM drive circuits:
motor relay disabled -106 short circuit or open circuit
Slowly press accelerator pedal -052
to the floor over a 5 second – Throttle valve opening set to -134 ECM ground circuit fault(s) (PI1-004, 005, 054)
period default value -004 Throttle motor failure
Slowly return the pedal to rest – Idle speed controlled by fuel -005 Throttle body failure
injection intervention -054
Repeat 3 times
– Idle speed adaption inhibited
– Speed control disabled
P1233 V8 SC Fuel pump 2 drive circuit fault Start engine 2 N ECM Default: PI1 ECM to Fuel Pump 2 Module control drive
EMS Battery voltage > 12 volts – Fuel pump 2 feedback control -053 circuit: open circuit, short circuit,
high resistance
OBD II Idle for 2 minutes inhibited
Fuel Pump 2 Module failure
P1234 EMS No fuel pump (1 SC) commands Start engine 2 N ECM Default: PI1 ECM to Rear Electronic Control Module drive
OBD II received by ECM Battery voltage > 12 volts – Fuel pump feedback control -027 circuit: open circuit, short circuit,
high resistance
Idle for 2 minutes inhibited
Rear Electronic Control Module failure
P1236 EMS Fuel pump (1 SC) not activated Start engine 2 N ECM Default: PI1 ECM to Rear Electronic Control Module drive
OBD II when requested by ECM Battery voltage > 12 volts – Fuel pump feedback control -027 circuit: open circuit, short circuit,
high resistance
Idle for 2 minutes inhibited
Rear Electronic Control Module failure
P1240 EMS Sensor power supply circuit Ignition ON 10 seconds 2 R None PI1 ECM to sensors sensor supply voltage
OBD II malfunction -012 circuit(s): short circuit to ground, short
-013 circuit to high voltage, open circuit,
high resistance
P1241 EMS Sensor power supply circuit Ignition ON 10 seconds 2 R ECM Default: PI1 ECM to sensors sensor supply voltage
OBD II low voltage – Throttle motor and throttle -012 circuit(s): short circuit to ground
motor relay disabled -013
– Throttle valve opening set to
default value
– Idle speed controlled by fuel
injection intervention
– Idle speed adaption inhibited
P1242 EMS Sensor power supply circuit Ignition ON 10 seconds 2 R ECM Default: PI1 ECM to sensors supply voltage circuit(s):
OBD II high voltage – Throttle motor and throttle -012 open circuit, high resistance, short circuit to
-013 high voltage
motor relay disabled
– Throttle valve opening set to
default value
– Idle speed controlled by fuel
injection intervention
– Idle speed adaption inhibited
P1243 EMS Sensor ground circuits Ignition ON 10 seconds 2 N None PI1 ECM to sensors sensor ground circuit(s):
OBD II open circuit -019 open circuit, high resistance
-020
P1244 V6 EMS Generator “CHARGE” circuit Battery voltage > 12 volts 2 C ECM Default: PI1 Generator to ECM “CHARGE” circuit:
OBD II high voltage / request low Switch OFF all electrical – Cooling fan speed increased -053 short circuit to high voltage
consumers Generator regulator failure
Start engine; idle for 16 Generator failure
minutes with all electrical
consumers switched OFF
P1245 EMS Engine crank signal low voltage Remove starter relay 2 N None PI1 Ignition switch to ECM circuit:: open circuit
OBD II Turn ignition switch to -006 Ignition switch failure
position III (START); hold for >
1 second
P1246 EMS Engine crank signal high voltage Drive vehicle > 15 km/h (9 2 N None PI1 Ignition switch to ECM circuit: short circuit to
OBD II mph) between 1500 – 4000 -006 high voltage
rpm for10 seconds; stop Ignition switch failure
vehicle
Repeat 5 times
P1250 EMS Throttle valve return spring Idle engine 2 R ECM Default: — Throttle return spring failure
OBD II malfunction Switch OFF ignition for 10 – Vehicle speed limited (throttle body failure)
seconds – Throttle opening limited to
Start engine and repeat 30%
– Speed control inhibited
P1251 EMS Throttle motor relay OFF failure Engine temperature cool 2 R ECM Default: PI1 Throttle motor relay coil power supply circuit:
OBD II (cooling fans not running) – Throttle motor and throttle -052 open circuit (fuse)
Remove ignition key for 20 motor relay disabled Throttle motor relay failure
seconds (cooling fans not – Throttle valve opening set to Throttle motor relay coil to ECM circuit:
running) default value open circuit
Ignition key in, position II for 5 – Idle speed controlled by fuel ECM ground circuit fault (relay coil drive)
seconds (do not start) injection intervention
Repeat cycle two additional – Idle speed adaption inhibited
times
P1254 EMS Throttle “limp home” spring Idle engine 2 R ECM Default: — Throttle limp home spring failure
OBD II malfunction Switch OFF ignition for 10 – Vehicle speed limited (throttle body failure)
seconds – Throttle opening limited to
Start engine and repeat 30%
– Speed control inhibited
P1260 EMS Security input malfunction Start engine N N None — Invalid ignition key code
JAG Passive anti-theft system (PATS) signal to
instrument pack missing or corrupted
Security message (PATS) CAN failure
NOTE: To clear this DTC, the failure must first
be rectified, followed by an ignition ON cycle
to allow a successful PATS identification
exchange between the ECM and the IC. The
fault code can then be cleared.
P1313 EMS Misfire rate catalyst damage – Misfire monitor drive cycle – 2 A ECM Default: — Cylinder compression low
OBD II bank 1 page 6 – Maximum engine speed Worn camshaft / broken valve spring(s)
reduced Fuel delivery pressure (low / high)
NOTE: This DTC will flag only Fuel injector(s) restricted / leaking
when accompanied by an
individual cylinder misfire DTC: Fuel injector(s) continuously open
P0300 – P0308 Fuel contamination
Fuel injector circuit fault(s)
(Injector DTCs also flagged)
Spark plug failure / fouled / incorrect gap
ECM to ignition coil primary circuit fault
(Cylinder misfire detected DTC also
flagged)
Ignition coil failure
P1314 EMS Misfire rate catalyst damage – Misfire monitor drive cycle – 2 A ECM Default: — Cylinder compression low
OBD II bank 2 page 6 – Maximum engine speed Worn camshaft / broken valve spring(s)
reduced Fuel delivery pressure (low / high)
NOTE: This DTC will flag only Fuel injector(s) restricted / leaking
when accompanied by an
individual cylinder misfire DTC: Fuel injector(s) continuously open
P0300 – P0308 Fuel contamination
Fuel injector circuit fault(s)
(Injector DTCs also flagged)
Spark plug failure / fouled / incorrect gap
ECM to ignition coil primary circuit fault
(Cylinder misfire detected DTC also
flagged)
Ignition coil failure
P1316 EMS Misfire excess emission Misfire monitor drive cycle – 2 N None — Cylinder compression low
OBD II page 6 Worn camshaft / broken valve spring(s)
NOTE: This DTC will flag only Fuel delivery pressure (low / high)
when accompanied by an Fuel injector(s) restricted / leaking
individual cylinder misfire DTC:
P0300 – P0308 Fuel injector(s) continuously open
Fuel contamination
Fuel injector circuit fault(s)
(Injector DTCs also flagged)
Spark plug failure / fouled / incorrect gap
ECM to ignition coil primary circuit fault
(Cylinder misfire detected DTC also
flagged)
Ignition coil failure
P1338 EMS Fuel pump (1 SC) drive circuit low Start engine 2 N ECM Default: PI1 Rear Electronic Control Module to fuel pump
OBD II / high voltage Battery voltage > 12 volts – Fuel pump feedback control -027 drive circuit: open circuit, short circuit,
high resistance
Idle for 2 minutes inhibited
Rear Electronic Control Module failure
Fuel pump failure
P1339 V8 SC Fuel pump 2 drive circuit low Start engine 2 N ECM Default: PI1 Fuel Pump 2 Module to fuel pump drive
EMS voltage / high voltage fault Battery voltage > 12 volts – Fuel pump 2 feedback control -053 circuit: open circuit, short circuit,
-011 high resistance
OBD II Idle for 2 minutes inhibited
Fuel Pump 2 Module to ECM monitor circuit:
open circuit, short circuit, high resistance
Fuel Pump 2 Module failure
Fuel pump 2 failure
P1340 EMS CMP Sensor 2 circuit malfunction Start engine; momentarily 2 N None PI1 CMP Sensor disconnected
OBD II – bank 2 race the engine; stop engine -068 CMP Sensor gap incorrect / foreign matter on
Repeat 2 additional times -069 sensor face
Idle engine 1 minute CMP Sensor sensing circuit:
open circuit, short circuit to ground,
short circuit to high voltage
CMP Sensor 2 failure
P1341 EMS CMP Sensor 2 circuit range / Start engine; momentarily 2 N None PI1 CMP Sensor disconnected
OBD II performance – bank 2 race the engine; stop engine -068 CMP Sensor gap incorrect / foreign matter on
Repeat 2 additional times -069 sensor face
Idle engine 1 minute CMP Sensor sensing circuit:
open circuit, short circuit to ground,
short circuit to high voltage
CMP Sensor 2 failure
P1344 EMS APP Sensor sense circuits APP1 Battery voltage > 10 volts 2 R ECM Default: PI1 APP Sensor to ECM sense circuits:
OBD II and APP2 range / performance Ignition ON – APP angle default value used -102 short circuit, open circuit, high resistance
-103 APP Sensor sensor supply circuits:
Slowly press accelerator pedal – Speed control inhibited short circuit, open circuit, high resistance
to the floor over a 5 second – APP adaptions (wear,
period APP Sensor sensor ground circuits:
variance) inhibited open circuit
Slowly return the pedal to rest
APP Sensor failure
Repeat 3 times
P1367 EMS Ignition amplifier bank 1 fault Start engine 2 A ECM Default: PI1 Ignition monitoring circuit between splice and
OBD II Battery voltage > 12 volts – Closed loop fuel metering -131 ECM: open circuit, short circuit to ground,
short circuit to B+ voltage
Idle for 2 minutes inhibited
Ignition module / coil bank 1 ground circuit
– Adaptive fuel metering fault
inhibited
– Catalyst warm up ignition
retard inhibited
– EGR Inhibited (V8)
– Canister purge inhibited
– Maximum engine speed
reduced
– Fuel injection cut off (bank 1
cylinders)
P1368 EMS Ignition amplifier bank 2 fault Start engine 2 A ECM Default: PI1 Ignition monitoring circuit between splice and
OBD II Battery voltage > 12 volts – Closed loop fuel metering -132 ECM: open circuit, short circuit to ground,
short circuit to B+ voltage
Idle for 2 minutes inhibited
Ignition module / coil bank 2 ground circuit
– Adaptive fuel metering fault
inhibited
– Catalyst warm up ignition
retard inhibited
– EGR Inhibited (V8)
– Canister purge inhibited
– Maximum engine speed
reduced
– Fuel injection cut off (bank 2
cylinders)
P1384 EMS VVT solenoid malfunction – Idle engine 30 seconds 2 N ECM Default: PI1 VVT solenoid valve 1 to ECM PWM drive
OBD II bank 1 Accelerate from stop through – Bank 1 VVT hold current set at -109 circuit fault
complete engine rpm range; a constant valve of 450 mA VVT solenoid valve 1 ground circuit fault
coast to a stop VVT solenoid 1 failure
Drive the vehicle steadily Oil contamination
between 48 – 97 km/h (30 –
60 mph) for 5 minutes; coast VVT 1 oil flow fault
to a stop VVT / camshaft mechanical failure – bank 1
Accelerate smoothly through
complete accelerator pedal
travel; coast to a stop
Idle engine 30 seconds
P1396 EMS VVT solenoid malfunction – Idle engine 30 seconds 2 N ECM Default: PI1 VVT solenoid valve 2 to ECM PWM drive
OBD II bank 2 Accelerate from stop through – Bank 2 VVT hold current set at -110 circuit fault
complete engine rpm range; a constant valve of 450 mA VVT solenoid valve 2 ground circuit fault
coast to a stop VVT solenoid 2 failure
Drive the vehicle steadily Oil contamination
between 48 – 97 km/h (30 –
60 mph) for 5 minutes; coast VVT 2 oil flow fault
to a stop VVT / camshaft mechanical failure – bank 2
Accelerate smoothly through
complete accelerator pedal
travel; coast to a stop
Idle engine 30 seconds
P1410 V8 SC Air cleaner solenoid valve drive Start engine N N None PI1 ECM to air cleaner solenoid circuit: open
EMS circuit malfunction Idle for 2 minutes -014 circuit, short circuit, high resistance
JAG Air cleaner solenoid failure
P1474 V8 SC Intercooler coolant pump Start engine and bring to 2 N ECM Default: — Intercooler coolant pump failure
EMS malfunction normal engine operating – Default value of 70 °C (158 °F)
OBD II temperature > 80 °C (176 °F) used
Drive vehicle in Drive at 80
km/h (50 mph) – 105 km/h (65
mph) for > 10 minutes.
P1516 EMS Gear change P / N driving Drive vehicle 2 A ECM Default: PI1 ECM P/N circuit: short circuit to ground, short
OBD II malfunction V6: > 15 km/h (9 mph) – Speed control inhibited -031 circuit to high voltage; high resistance
between 1500 – 4000 rpm; Gear selector cable setting incorrect
– Maximum engine speed
engine load > 0.40 g/rpm reduced J Gate assembly incorrect setting
Continue for 30 seconds J Gate / ECM CAN fault
V8: > 24 km/h (15 mph)
between 1500 – 4000 rpm for
30 seconds
P1517 EMS Gear change P / N starting Start engine in P 2 A ECM Default: PI1 ECM P/N circuit: short circuit to ground, short
OBD II malfunction Start engine in N – Speed control inhibited -031 circuit to high voltage; high resistance
Gear selector cable setting incorrect
Check that engine does not – Maximum throttle opening for
start in R, D, 5, 4, 3, 2 N range inhibited J Gate assembly incorrect setting
– Maximum engine speed J Gate / ECM CAN fault
reduced
P1532 V6 EMS IMT valve 2 (bottom) circuit Battery voltage > 12 volts 2 N ECM Default: PI1 IMT Valve 2 (bottom) disconnected
OBD II malfunction Start engine and bring to – IMT 2 Inhibited -039 IMT Valve 2 (bottom) to ECM drive circuit fault
normal operating temperature IMT Valve 2 (bottom) power supply circuit fault
> 82 °C (180 °F)
IMT Valve 2 (bottom) failure
Run engine at 5000 rpm in N
for 20 seconds
P1549 V6 EMS IMT valve 1 (top) circuit Battery voltage > 12 volts 2 N ECM Default: PI1 IMT Valve 1 (top) disconnected
OBD II malfunction Start engine and bring to – IMT 1 Inhibited -038 IMT Valve 1 (top) to ECM drive circuit fault
normal operating temperature IMT Valve 1 (top) power supply circuit fault
> 82 °C (180 °F)
IMT Valve 1 (top) failure
Run engine at 5000 rpm in N
for 20 seconds
P1571 EMS Brake ON / OFF switch; brake Start engine; idle in P, N N A ECM Default: PI1 Brake ON / OFF switch to ECM circuit:
JAG cancel switch malfunction Press brake pedal for > 30 – Speed control inhibited -008 open circuit, short circuit to ground,
-009 high resistance
(Brake ON / OFF switch – seconds; release brake pedal – Maximum engine speed
normally open; brake cancel Brake ON / OFF power supply circuit:
Repeat 10 times reduced open circuit
switch – normally closed)
– or– – J Gate locked in Park Brake ON / OFF switch failure
Drive > 80 km/h (50 mph) > 1 Brake cancel switch to ECM circuit:
minute (do not press the open circuit, short circuit to ground,
brake pedal); momentarily high resistance
press the brake pedal Brake cancel switch power supply circuit:
Repeat 10 times open circuit
–or– Brake cancel switch failure
Using WDS, monitor both
circuits
Pedal at rest = “0” (both
circuits); pedal pressed = “1”
(both circuits)
P1582 EMS “Flight recorder” data is stored if 1 Inertia switch activated N N None PI1 If none of the five conditions occur, check:
JAG any one of five conditions occur: 2 Throttle Limp Home mode -010 Inertia switch to ECM circuit:
short circuit to B+ voltage
3 Engine starts and stumbles
Inertia switch failure
4 Engine fail to start
5 Engine stall
P1603 TRANS TCM Internal communications Ignition ON 10 seconds 1 A None — TCM / Control valve failure
OBD II error
P1605 TRANS TCM RAM error Ignition ON, then OFF. Cycle N N None GB2 Battery power supply circuit: open circuit,
JAG ignition switch 6 times. -14 short circuit to ground
TCM / Control valve failure
P1606 EMS EMS control relay malfunction Engine temperature cool 1 N None PI1 ECM control relay failure
OBD II (cooling fans not running) -040 ECM control relay to ECM circuit fault
Remove ignition key for 1 ECM control relay coil power supply open
minute (cooling fans not circuit
running)
ECM ground circuit fault (relay coil drive)
Ignition key in, position II for 5
seconds (do not start)
P1609 EMS ECM microprocessor to Ignition ON 10 seconds 2 R ECM Default: — ECM Failure
OBD II microprocessor communication – Throttle motor and throttle
failure motor relay disabled
– Throttle valve opening set to
default value
– Idle speed controlled by fuel
injection intervention
– Idle speed adaption inhibited
P1611 EMS ECM sub CPU failure Drive vehicle 2 R ECM Default: — ECM Failure
OBD II If fitted, engage speed control – Throttle motor and throttle
Refer to Owner’s Handbook motor relay disabled
and ensure that speed control – Throttle valve opening set to
engages normally default value
– Idle speed controlled by fuel
injection intervention
– Idle speed adaption inhibited
P1629 V6 EMS Generator “FIELD” circuit failure Battery voltage > 12 volts 2 C None PI1 ECM to generator “FIELD” return circuit:
OBD II Switch OFF all electrical -065 open circuit, high resistance
consumers Generator regulator failure
Ignition ON 15 seconds Generator failure
Start engine; momentarily idle
with all electrical consumers
switched OFF
Switch ignition OFF
Switch ignition ON
P1631 EMS Throttle motor relay coil drive Engine temperature cool 2 R ECM Default: PI1 Throttle motor relay coil power supply circuit:
OBD II circuit OFF failure (cooling fans not running) – Throttle motor and throttle -052 open circuit (fuse)
Remove ignition key for 20 motor relay disabled Throttle motor relay failure
seconds (cooling fans not – Throttle valve opening set to Throttle motor relay coil to ECM drive circuit:
running) default value open circuit, short circuit to ground
Ignition key in, position II for 5 – Idle speed controlled by fuel
seconds (do not start) injection intervention
Repeat cycle twice more – Idle speed adaption inhibited
P1632 EMS Generator charge system failure / Battery voltage > 12 volts 2 C None PI1 ECM to generator “LOAD” feedback circuit:
OBD II generator “LOAD” feedback Switch OFF all electrical -079 short circuit, open circuit, high resistance
circuit failure consumers Generator regulator failure
Start engine; idle for 16 Generator failure
minutes with all electrical
consumers switched OFF
If no reoccurrence of DTC(s):
hold engine > 1500 rpm for
one minute in N
P1633 EMS ECM main CPU failure Ignition ON 10 seconds 2 R ECM Default: — ECM Failure
OBD II – Throttle motor and throttle
motor relay disabled
– Throttle valve opening set to
default value
– Idle speed controlled by fuel
injection intervention
– Idle speed adaption inhibited
P1634 EMS Throttle “watch dog” circuit Idle engine 2 R ECM Default: — ECM Failure
OBD II malfunction Switch OFF ignition for 10 – Vehicle speed limited
seconds – Throttle opening limited to
Start engine and repeat 30%
– Speed control inhibited
P1637 EMS CAN ECM to DSCCM network Ignition ON 10 seconds 2 A ECM Default: PI1 CAN open circuit fault – DSCCM to ECM
OBD II malfunction – Speed control inhibited -123 CAN short circuit fault
-124
– Maximum throttle opening for DSCCM failure
N range inhibited ECM failure
– Throttle opening limited to
30%
– Maximum engine speed
reduced
P1638 EMS CAN ECM / IC network Ignition ON 10 seconds 1 N None PI1 CAN open circuit fault – IC to ECM
OBD II malfunction (Engine will not start – PATS -123 CAN short circuit fault
failure) -124
IC failure
ECM failure
P1642 EMS CAN circuit malfunction Ignition ON 10 seconds 1 A ECM Default: PI1 CAN short circuit fault
OBD II – Speed control inhibited -123 Control module failure –
-124 check for additional flagged DTC(s) to locate
– Maximum throttle opening for control module source
N range inhibited
– Throttle opening limited to
30%
– Maximum engine speed
reduced
(Engine will not start – PATS
failure)
P1643 EMS CAN ECM / TCM network Ignition ON 10 seconds 2 A ECM Default: PI1 CAN open circuit fault – TCM to ECM
OBD II malfunction – Speed control inhibited -123 CAN short circuit fault
-124
– Maximum throttle opening for TCM failure
N range inhibited ECM failure
– Throttle opening limited to
30%
– Maximum engine speed
reduced
P1646 EMS ECM HO2 Sensor control Drive vehicle for 10 minutes 2 N ECM Default: — HO2 Sensor 1/1 heater failure
OBD II malfunction – – HO2S 1/1 control circuit HO2 Sensor 1/1 sensing circuit:
bank 1 upstream (1/1) inhibited short circuit to ground, short circuit to
high voltage, open circuit, high resistance
ECM Failure
P1647 EMS ECM HO2 Sensor control Drive vehicle for 10 minutes 2 N ECM Default: — HO2 Sensor 2/1 heater failure
OBD II malfunction – – HO2S 2/1 control circuit HO2 Sensor 2/1 sensing circuit:
bank 2 upstream (2/1) inhibited short circuit to ground, short circuit to
high voltage, open circuit, high resistance
ECM Failure
P1648 EMS ECM internal Knock Sensor CPU Start engine 2 A ECM Default: — ECM Failure
OBD II self test failure Battery voltage > 12 volts. – Maximum ignition retard
Idle for 2 minutes – Maximum engine speed
reduced
P1656 EMS TP Sensor amplifier circuit Ignition ON 10 seconds 2 A ECM Default: PI1 ECM Failure
OBD II malfunction – Maximum engine speed -075
reduced
P1657 EMS Throttle motor relay coil drive Engine temperature cool 2 R ECM Default: PI1 Throttle motor relay failure
OBD II circuit ON failure (cooling fans not running) – Vehicle speed limited -052 Throttle motor relay coil to ECM drive circuit:
Remove ignition key for 20 -134 short circuit to B+ voltage
– Throttle opening limited to
seconds (cooling fans not 30%
running)
– Speed control inhibited
Ignition key in, position II for 5
seconds (do not start)
Repeat cycle two additional
times
P1658 EMS Throttle motor relay ON failure Engine temperature cool 2 R ECM Default: PI1 Throttle motor relay failure
OBD II (cooling fans not running) – Vehicle speed limited -052 Throttle motor relay coil to ECM drive circuit:
Remove ignition key for 20 short circuit to B+ voltage
– Throttle opening limited to
seconds (cooling fans not 30%
running)
– Speed control inhibited
Ignition key in, position II for 5
seconds (do not start)
Repeat cycle two additional
times
P1696 EMS CAN ECM / ASCCM network Ignition ON 30 seconds N N ECM Default: PI1 CAN open circuit fault – ASCCM to ECM
JAG malfunction – Speed control inhibited -123 CAN short circuit fault
-124
ASCCM failure
ECM failure
P1697 EMS Adaptive speed control Ignition ON 45 seconds N A ECM Default: PI1 Speed control switches internal steering
JAG HEADWAY switch(es) circuit – Speed control inhibited -047 wheel circuit: short circuit to ground
malfunction Steering wheel cassette reel:
short circuit to ground
Cassette reel to ECM circuit:
short circuit to ground
HEADWAY + / - switch(es) failure (stuck ON)
P1699 EMS CAN ECM / A/CCM network Ignition ON 10 seconds 2 N None PI1 CAN open circuit fault – A/CCM to ECM
OBD II malfunction -123 CAN short circuit fault
-124
A/CCM failure
ECM failure
P1749 TRANS PARK / NEUTRAL circuit Ignition ON. Move gear N N None GB2 TCM TO ECM P / N circuit: open circuit, short
JAG malfunction selector to N; leave in N for 5 -10 circuit to ground, short circuit to B+ voltage
seconds, then return to P. TCM / Control valve failure
P1774 TRANS CAN TCM / J Gate Module Ignition ON 10 seconds N A TCM Default: GB2 CAN open circuit fault – TCM to J Gate
JAG network malfunction – Manual gear selection -2 Module
disabled -6 CAN short circuit fault
– Sport mode disabled J Gate Module failure
P1783 TRANS Transmission over-temperature Drive vehicle for 1 hour while N A TCM Default: — Transmission fluid level low
OBD II shut-down continually performing hard – Mechanical limp home mode Transmission fluid cooler circuit:
acceleration starts / stops. obstructed, leaking
Transmission fluid cooler fins blocked by
debris
Transmission mechanical failure
P1794 TRANS TCM ignition switched power Ignition ON 10 seconds 2 A TCM Default: GB2 Ignition switched power supply fuse failure
OBD II supply circuit malfunction – Mechanical limp home mode -9 Ignition switched power supply circuit:
short circuit to ground, open circuit
P1796 TRANS CAN network fault Ignition ON 10 seconds 2 A TCM Default: GB2 CAN open circuit or short circuit fault
OBD II – Mechanical limp home mode -2 TCM / Control valve failure
-6
P1797 TRANS CAN TCM / ECM network Ignition ON 10 seconds 2 A TCM Default: GB2 CAN open circuit fault – TCM to ECM
OBD II malfunction – Mechanical limp home mode -2 CAN short circuit fault
-6
ECM failure
TCM / Control valve failure
P1798 TRANS CAN TCM / IC network Ignition ON 10 seconds N N None GB2 CAN open circuit fault – TCM to IC
JAG malfunction -2 CAN short circuit fault
-6
IC failure
TCM / Control valve failure
P1799 TRANS CAN TCM / DSCCM network Ignition ON 10 seconds N N TCM Default: GB2 CAN open circuit fault – TCM to DSCCM
JAG malfunction – Substitute transmission -2 CAN short circuit fault
output speed for DSC vehicle -6
DSCCM failure
speed
TCM / Control valve failure
SYSTEM The vehicle system the DTC is associated with. Refer to the applicable Electrical Guide Figure for circuit details.
FAULT DESCRIPTION Fault description. If available, customer symptom (complaint) information is provided in this column.
MIL Y = System MIL (if fitted) is activated.
N = System MIL (if fitted) is not activated.
M = Message displayed.
B1200 A/CCM Climate control Climate control push button circuit failure N Internal A/CCM failure
B1201 RECM Instrument pack Fuel level sensor circuit(s) fault N RECM to fuel level sensor circuit(s) (CA101-15, CA101-16): open circuit,
short circuit to ground, short circuit to B+ voltage, short circuit to each
other, high resistance
CUSTOMER SYMPTOM: Inaccurate fuel level Fuel level sensor failure
B1205 MC Instrument pack Message center switch pack circuit fault N Instrument pack to message center switch pack circuit(s): open circuit,
short circuit to ground, short circuit to B+ voltage, high resistance
Message center switch pack failure
CUSTOMER SYMPTOM: Message center switches
inoperative
B1213 INST Security Less than two (2) keys are programmed N Program at least two keys using PDU
B1231 RCM SRS Airbag Crash data memory full Y Replace RCM
B1242 A/CCM Climate control Fresh / recirculation air flow actuator motor drive circuit N A/CCM to actuator drive circuit(s): high resistance, open circuit, short
fault circuit to ground, or short circuit to each other
Fresh / recirculation air flow actuator position feedback reference voltage
circuit: open circuit, short circuit to ground or B+ voltage
Fresh / recirculation air flow actuator position feedback circuit: open circuit,
CUSTOMER SYMPTOM: No variable air flow direction short circuit to ground
control Fresh / recirculation air flow actuator failure
B1246 INST Interior lighting Interior lighting master switch / dimmer switch circuit N Instrument pack to switches signal circuit (FC63-16): open circuit, short
fault circuit to ground, short circuit to B+ voltage, high resistance
Dimmer-controlled lighting
Dimmer switch failure
CUSTOMER SYMPTOM: Both interior lighting master Interior lighting master switch failure
switch and dimmer switch inoperative
B1251 A/CCM Climate control In-car temperature sensor circuit open circuit N In-car temperature sensor disconnected
A/CCM to in-car temperature sensor sensing circuit (FC28-09) open circuit
CUSTOMER SYMPTOM: No automatic temperature In-car temperature sensor failure
control
B1253 A/CCM Climate control In-car temperature sensor circuit short circuit to ground N A/CCM to in-car temperature sensor sensing circuit (FC28-09) short circuit
to ground
In-car temperature sensor failure
CUSTOMER SYMPTOM: No automatic temperature
control
B1255 A/CCM Climate control Ambient air temperature sensor circuit open circuit N Ambient air temperature sensor disconnected
A/CCM to ambient air temperature sensor sensing circuit (FC28-17) open
circuit
CUSTOMER SYMPTOM: Inaccurate exterior
temperature displayed Ambient air temperature sensor failure
B1257 A/CCM Climate control Ambient air temperature sensor circuit short circuit to N A/CCM to ambient air temperature sensor sensing circuit (FC28-17) short
ground circuit to ground
Ambient air temperature sensor failure
CUSTOMER SYMPTOM: Inaccurate exterior
temperature displayed
B1259 A/CCM Climate control Dual solar sensor sensing circuit(s) open circuit N Dual solar sensor disconnected
A/CCM to dual solar sensor sensing circuit(s) (FC28-07 – LH, FC28-20 – RH)
open circuit
CUSTOMER SYMPTOM: Poor automatic temperature
control in high sun load conditions Dual solar sensor failure
B1261 A/CCM Climate control Dual solar sensor sensing circuit(s) short circuit to N A/CCM to dual solar sensor sensing circuit(s) (FC28-07 – LH, FC28-20 – RH)
ground short circuit to ground
Dual solar sensor failure
CUSTOMER SYMPTOM: Poor automatic temperature
control in high sun load conditions
B1262 A/CCM Climate control Defrost mode actuator motor drive circuit fault N A/CCM to actuator drive circuit(s): high resistance, open circuit, short
circuit to ground, or short circuit to each other
Defrost mode actuator position feedback reference voltage circuit: open
circuit, short circuit to ground or B+ voltage
Defrost mode actuator position feedback circuit: open circuit, short circuit
CUSTOMER SYMPTOM: No defrost air flow direction to ground
control Defrost mode actuator failure
B1263 A/CCM Climate control Panel mode actuator motor drive circuit fault N A/CCM to actuator drive circuit(s): high resistance, open circuit, short
circuit to ground, or short circuit to each other
Panel mode actuator position feedback reference voltage circuit: open
circuit, short circuit to ground or B+ voltage
Panel mode actuator position feedback circuit: open circuit, short circuit to
CUSTOMER SYMPTOM: No panel air flow direction ground
control Panel mode actuator failure
B1264 A/CCM Climate control Floor mode actuator motor drive circuit fault N A/CCM to actuator drive circuit(s): high resistance, open circuit, short
circuit to ground, or short circuit to each other
Floor mode actuator position feedback reference voltage circuit: open
circuit, short circuit to ground or B+ voltage
Floor mode actuator position feedback circuit: open circuit, short circuit to
CUSTOMER SYMPTOM: No floor air flow direction ground
control Floor mode actuator failure
B1265 A/CCM Climate control Cold air bypass actuator motor drive circuit fault N A/CCM to actuator drive circuit(s): high resistance, open circuit, short
circuit to ground, or short circuit to each other
Cold air bypass actuator position feedback reference voltage circuit: open
circuit, short circuit to ground or B+ voltage
Cold air bypass actuator position feedback circuit: open circuit, short circuit
CUSTOMER SYMPTOM: No bypass air flow direction to ground
control Cold air bypass actuator failure
B1299 RPACM Reverse parking aid Ignition switched power supply fault N RPACM ignition switched power supply circuit: open circuit, short circuit to
ground
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
B1309 DDCM Central door locking Driver door lock circuit short circuit to ground N DDCM to driver door latch assembly lock circuit (DT2-8) short circuit to
ground
Driver door latch assembly failure
CUSTOMER SYMPTOM: Driver door lock switch
inoperative
B1318 RCM SRS Airbag Ignition switched power supply low voltage Y Ignition switched power supply open circuit
Charging system low voltage fault
B1319 GECM Interior lighting Driver door switch circuit fault N GECM to driver door switch circuit (CA31-8): open circuit, short circuit to
Central door locking ground, short circuit to B+ voltage
Driver door switch ground fault
Security CUSTOMER SYMPTOM – GECM systems effected:
Driver door switch failure
Interior lighting – lamps inoperative or always on
Central door locking
Security
B1327 GECM Interior lighting Passenger door switch circuit fault N GECM to passenger door switch circuit (CA31-8): open circuit, short circuit
Central door locking to ground, short circuit to B+ voltage
Passenger door switch ground fault
Security CUSTOMER SYMPTOM – GECM systems effected:
Passenger door switch failure
Interior lighting – lamps inoperative or always on
Central door locking
Security
B1331 RECM Interior lighting Trunk switch circuit fault N RECM to trunk switch circuit (CA102-14): open circuit, short circuit to
Central door locking ground, short circuit to B+ voltage
Trunk switch ground fault
Security
CUSTOMER SYMPTOM – RECM systems effected: Trunk switch failure
Interior lighting – trunk lamps inoperative or always on
Central door locking
Security
B1335 RECM Interior lighting RH rear door switch circuit fault N RECM to RH rear door switch circuit (CA101-17 LHD, CA103-16 RHD):
Central door locking open circuit, short circuit to ground, short circuit to B+ voltage
RH rear door switch ground fault
Security
CUSTOMER SYMPTOM – RECM systems effected: RH rear door switch failure
Interior lighting – interior lamps inoperative or always on
Central door locking
Security
B1341 DDCM Central door locking Driver door unlock circuit short circuit to ground N DDCM to driver door latch assembly unlock circuit (DT2-9) short circuit to
ground
Driver door latch assembly failure
CUSTOMER SYMPTOM: Driver door lock switch
inoperative
B1342 ABS/ Anti-lock braking / traction Control module failure Y ABS/TCCM failure
TCCM control
CUSTOMER SYMPTOM: MIL warning; default
operation
B1342 ADCM Suspension adaptive damping Control module failure M ADCM failure
(CATS)
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
B1342 AUDIO In-car entertainment Control module failure N Radio head unit failure
B1342 DSCCM Dynamic stability control Control module failure Y DSCCM failure
B1342 INST Instrument pack Control module failure N Instrument pack failure
B1342 RPACM Reverse parking aid Control module failure N RPACM failure
B1342 SCLCM Security (steering column lock Control module failure N SCLCM failure
control module)
CUSTOMER SYMPTOM: Steering column locking
inoperative
B1342 VECM Telephone with voice control and Control module failure N VECM failure
vehicle emergency message
system (VEMS)
CUSTOMER SYMPTOM: VEMS inoperative
B1352 INST Instrument pack Ignition “key-in” switch circuit fault N Instrument pack to key-in switch circuit (FC14-21): open circuit, short
CUSTOMER SYMPTOM: Key-in audible warning circuit to ground
inoperative; steering column and driver seat entry / exit Key-in switch failure
memory functions inoperative
B1400 DDCM Window lifts Driver window “one touch down” signal circuit fault N DDCM to driver door switch pack window “one touch” circuit (DD4-21)
short circuit to B+ voltage
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver window “one touch
down” always active
B1405 DDCM Window lifts Driver window down signal circuit fault N DDCM to driver door switch pack driver window down circuit (DD4-20)
short circuit to B+ voltage
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver window switch
inoperative
B1408 DDCM Window lifts Driver window up signal circuit fault N DDCM to driver door switch pack driver window up circuit (DD4-19) short
circuit to B+ voltage
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver window switch
inoperative
B1416 DDCM Window lifts LH rear window up / down signals circuit fault N DDCM to driver door switch pack LH rear window circuit(s) (DD4-8;
DD4-9) short circuit to B+ voltage
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver door switch pack LH
rear window switch inoperative
B1420 DDCM Window lifts Passenger window up / down signals circuit fault N DDCM to driver door switch pack passenger window circuit(s) (DD4-2;
DD4-3) short circuit to B+ voltage
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver door switch pack
passenger window switch inoperative
B1424 DDCM Window lifts RH rear window up / down signals circuit fault N DDCM to driver door switch pack RH rear window circuit(s) (DD4-4;
DD4-5) short circuit to B+ voltage
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver door switch pack RH
rear window switch inoperative
B1438 GECM Wash / wipe system Wiper mode select switch circuit fault N GECM to wipe / wash switch wiper mode select circuit (CA31-2): open
circuit, short circuit to ground, short circuit to B+ voltage
Wipe / wash switch failure
CUSTOMER SYMPTOM: Windshield wipers
inoperative
B1446 GECM Wash / wipe system Windshield wiper motor park sense circuit fault N GECM to wiper park switch circuit (FH9-13): open circuit, short circuit to
ground, short circuit to B+ voltage
Wiper park switch failure
CUSTOMER SYMPTOM: Incorrect windshield wiper
operation
B1470 INST Exterior lighting: front Headlamp switch circuit fault N Instrument pack to lighting switch (headlamps) circuit (FC63-12): open
circuit, short circuit
Lighting switch failure
CUSTOMER SYMPTOM: Headlamp switch inoperative
B1472 INST Instrument pack Seat belt switch circuit fault Y Instrument pack to seat belt switch circuit (FC14-18): open circuit, short
circuit to ground, short circuit to B+ voltage
Seat belt switch ground fault
Seat belt switch failure
B1479 GECM Wash / wipe system Washer fluid level switch circuit fault Y GECM to fluid level switch circuit (FH9-15): open circuit, short circuit to
ground, short circuit to B+ voltage
Washer fluid level switch ground fault
CUSTOMER SYMPTOM: Low fluid MIL on or off
continuously; programmed wash / wipe inoperative Washer fluid level switch failure
B1483 RECM Exterior lighting: rear Brake (stop lamp) switch circuit fault N Brake switch battery power supply open circuit
RECM to brake switch circuit open circuit, short circuit to ground, short
circuit to B+ voltage
CUSTOMER SYMPTOM: Stop lamps inoperative or
always on Brake switch failure
B1485 ABS/ Anti-lock braking / traction Brake (stop lamp) switch circuit fault N Brake switch battery power supply open circuit
TCCM control DSCCM to brake switch circuit open circuit, short circuit to ground, short
circuit to B+ voltage
Brake switch failure
B1485 DSCCM Dynamic stability control Brake (stop lamp) switch circuit fault N Brake switch battery power supply open circuit
DSCCM to brake switch circuit: open circuit, short circuit to ground, short
circuit to B+ voltage
Brake switch failure
B1499 GECM Exterior lighting: front LH front turn signal circuit fault N LH front turn signal bulb failure
GECM to LH front turn signal (headlamp unit) circuit (FH60-5): open circuit,
short circuit to ground
CUSTOMER SYMPTOM: LH front turn signal LH headlamp unit failure
inoperative; LH front turn signal always on GECM failure
B1499 RECM Exterior lighting: rear LH rear turn signal circuit fault N LH rear turn signal bulb failure
RECM to LH rear turn signal (tail lamp unit) circuit (CA63-3): open circuit,
short circuit to ground
CUSTOMER SYMPTOM: LH rear turn signal LH tail lamp unit failure
inoperative; LH rear turn signal always on RECM failure
B1501 GECM Exterior lighting: front LH front turn signal circuit B+ voltage fault N GECM to LH front turn signal (headlamp unit) circuit (FH60-5): short circuit
to B+ voltage
LH headlamp unit failure
CUSTOMER SYMPTOM: LH front turn signal
inoperative; LH front turn signal always on GECM failure
B1501 RECM Exterior lighting: rear LH rear turn signal circuit B+ voltage fault N RECM to LH rear turn signal (tail lamp unit) circuit (CA63-3): short circuit to
B+ voltage
LH tail lamp unit failure
CUSTOMER SYMPTOM: LH rear turn signal
inoperative; LH rear turn signal always on RECM failure
B1503 GECM Exterior lighting: front RH front turn signal circuit fault N RH front turn signal bulb failure
GECM to RH front turn signal (headlamp unit) circuit (FH60-4): open circuit,
short circuit to ground
CUSTOMER SYMPTOM: RH front turn signal RH headlamp unit failure
inoperative; RH front turn signal always on GECM failure
B1503 RECM Exterior lighting: rear RH rear turn signal circuit fault N RH rear turn signal bulb failure
RECM to RH rear turn signal (tail lamp unit) circuit (CA63-4): open circuit,
short circuit to ground
CUSTOMER SYMPTOM: RH rear turn signal RH tail lamp unit failure
inoperative; RH rear turn signal always on RECM failure
B1505 GECM Exterior lighting: front RH front turn signal circuit B+ voltage fault N GECM to RH front turn signal (headlamp unit) circuit (FH60-4): short circuit
to B+ voltage
RH headlamp unit failure
CUSTOMER SYMPTOM: RH front turn signal
inoperative; RH front turn signal always on GECM failure
B1505 RECM Exterior lighting: rear RH rear turn signal circuit B+ voltage fault N RECM to RH rear turn signal (tail lamp unit) circuit (CA63-4): short circuit to
B+ voltage
RH tail lamp unit failure
CUSTOMER SYMPTOM: RH rear turn signal
inoperative; RH rear turn signal always on RECM failure
B1519 GECM Security Hood switch circuit fault N GECM to hood switch circuit (FH59-3): open circuit, short circuit to ground,
short circuit to B+ voltage
Hood switch ground fault
CUSTOMER SYMPTOM: Security system does not
arm; security system functions incorrectly Hood switch failure
B1530 DDCM Memory functions: Memory set switch circuit fault N DDCM to driver door switch pack memory set switch circuit (DD4-25) short
Steering column movement circuit to ground
Door mirror movement Driver door switch pack failure
CUSTOMER SYMPTOM: Memory set switch
Driver seat movement inoperative
B1534 DDCM Memory functions: Memory 1 switch circuit fault N DDCM to driver door switch pack memory 1 switch circuit (DD4-10) short
Steering column movement circuit to ground
Door mirror movement Driver door switch pack failure
Driver seat movement CUSTOMER SYMPTOM: Memory 1 switch inoperative
B1538 DDCM Memory functions: Memory 2 switch circuit fault N DDCM to driver door switch pack memory 2 switch circuit (DD4-11) short
Steering column movement circuit to ground
Door mirror movement Driver door switch pack failure
Driver seat movement CUSTOMER SYMPTOM: Memory 2 switch inoperative
B1551 RECM Central door locking Trunk release circuit fault N RECM to trunk release circuit (CA103-10): open circuit, short circuit to
ground
Trunk release ground fault
CUSTOMER SYMPTOM: Trunk will not release Trunk release failure
B1567 GECM Exterior lighting: front Headlamp main beam circuit(s) fault N Headlamp bulb failure
GECM to headlamp main beam bulbs circuit(s) (FH60-10, FH60-17): open
circuit, short circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Headlamp main beam(s)
inoperative; headlamp main beam(s) always on Headlamp unit failure
B1567 INST Exterior lighting: front Headlamp main / dip / flash switch circuit fault N Instrument pack to lighting stalk switch circuit (FC15-19): short circuit to
ground, short circuit to B+ voltage
Lighting stalk switch failure
CUSTOMER SYMPTOM: Headlamp main / dip / flash
switch inoperative
B1571 RECM Interior lighting LH rear door switch circuit fault N RECM to LH rear door switch circuit (CA103-16 LHD, CA101-17 RHD):
Central door locking open circuit, short circuit to ground, short circuit to B+ voltage
LH rear door switch ground fault
Security
CUSTOMER SYMPTOM – RECM systems effected: LH rear door switch failure
Interior lighting – interior lamps inoperative or always on
Central door locking
Security
B1600 INST Battery; starter; generator Ignition key transponder signal is not received N Incorrect ignition key(s)
Security Reconfigure instrument pack for ignition keys using PDU
CUSTOMER SYMPTOM: Engine will not start Passive anti-theft system transceiver failure
B1601 INST Battery; starter; generator Instrument pack passive anti-theft system module N Reprogram instrument pack for ignition keys using PDU
Security (PATS) received incorrect ignition key code from PATS Passive anti-theft system transceiver failure
transceiver
B1602 INST Battery; starter; generator Instrument pack passive anti-theft system module N Passive anti-theft system transceiver failure
Security (PATS) received invalid form of ignition key code from
PATS transceiver
B1629 RPACM Reverse parking aid Reverse lamps activated input circuit fault N RPACM reverse sensing circuit (CA112-9) short circuit to B+ voltage
B1676 ABS/ Anti-lock braking / traction Battery voltage out of range: 9 v – 16 v Y Charging system low / high voltage fault
TCCM control
CUSTOMER SYMPTOM: MIL warning;
default operation
B1676 A/CCM Climate control Battery voltage out of range: 9 v – 16 v N Charging system low / high voltage fault
B1676 DDCM Various – Battery voltage out of range: 9 v – 16 v N Charging system low / high voltage fault
see FAULT DESCRIPTION
CUSTOMER SYMPTOM – DDCM systems effected:
Memory set functions
Driver door mirror movement
Driver door locking
Remote keyless entry functions
Security alarm set / reset functions
Window lift function from driver door switch pack
Driver window lift
B1676 DSCCM Dynamic stability control Battery voltage out of range: 9 v – 16 v Y Charging system low / high voltage fault
B1676 DSCM Driver seat Battery voltage out of range: 9 v – 16 v N Charging system low / high voltage fault
B1676 GECM Various – Battery voltage out of range: 9 v – 16 v N Charging system low / high voltage fault
see FAULT DESCRIPTION
CUSTOMER SYMPTOM – GECM systems effected:
Switched system power SCP functions
Security
Interior lighting
Dimmer controlled lighting
Variable assist power steering
Passenger door mirror movement
Central door locking
Windshield wash / wipe
Window lifts
B1676 INST Instrument pack Battery voltage out of range: 9 v – 16 v N Charging system low / high voltage fault
B1676 RECM Various – Battery voltage out of range: 9 v – 16 v N Charging system low / high voltage fault
see FAULT DESCRIPTION
CUSTOMER SYMPTOM – GECM systems effected:
Switched system power SCP functions
Fuel pump (engine management)
Climate control
Instrument pack
Exterior lighting: rear
Interior lighting
Heated backlight
Central door locking
Security
Window lifts
B1681 INST Battery; starter; generator Instrument pack passive anti-theft system (PATS) N Instrument pack to passive anti-theft system transceiver circuit(s) (FC15-4,
Security module does not receive PATS transceiver signal FC15-5): open circuit, short circuit to ground, short circuit to each other,
short circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: Engine will not start Passive anti-theft system transceiver failure
B1689 INST Exterior lighting: front Autolamps switch circuit fault N Instrument pack to lighting switch (autolamps) circuit (FC63-14): open
circuit, short circuit
Lighting switch failure
CUSTOMER SYMPTOM: Headlamp autolamp function
inoperative
B1703 DSCM Driver seat Seat recline forward switch circuit fault N Seat recline forward switch circuit (DM9-12) short circuit to B+ voltage
Seat recline forward switch failure
CUSTOMER SYMPTOM: Erratic operation;
recline forward inoperative
B1707 DSCM Driver seat Seat recline rearward switch circuit fault N Seat recline rearward switch circuit (DM9-4) short circuit to B+ voltage
Seat recline rearward switch failure
CUSTOMER SYMPTOM: Erratic operation;
recline rearward inoperative
B1711 DSCM Driver seat Seat front raise switch circuit fault N Seat front raise switch circuit (DM9-13) short circuit to B+ voltage
Seat raise switch failure
CUSTOMER SYMPTOM: Erratic operation;
seat front raise inoperative
B1715 DSCM Driver seat Seat front lower switch circuit fault N Seat front lower switch circuit (DM9-5) short circuit to B+ voltage
Seat lower switch failure
CUSTOMER SYMPTOM: Erratic operation;
seat front lower inoperative
B1719 DSCM Driver seat Seat forward switch circuit fault N Seat forward switch circuit (DM9-3) short circuit to B+ voltage
Seat forward switch failure
CUSTOMER SYMPTOM: Erratic operation;
seat forward inoperative
B1723 DSCM Driver seat Seat rearward switch circuit fault N Seat rearward circuit (DM9-11) short circuit to B+ voltage
Seat rearward switch failure
CUSTOMER SYMPTOM: Erratic operation;
seat rearward inoperative
B1727 DSCM Driver seat Seat rear raise switch circuit fault N Seat rear raise switch circuit (DM9-14) short circuit to B+ voltage
Seat rear raise switch failure
CUSTOMER SYMPTOM: Erratic operation;
seat rear raise inoperative
B1731 DSCM Driver seat Seat rear lower switch circuit fault N Seat rear lower switch circuit (DM9-6) short circuit to B+ voltage
Seat rear lower switch failure
CUSTOMER SYMPTOM: Erratic operation;
seat rear lower inoperative
B1757 DSCM Driver seat Seat cushion rear motor or position sensor circuit(s) N Seat cushion rear position sensor failure
fault Seat cushion rear motor failure
B1761 DSCM Driver seat Seat cushion front motor or position sensor circuit(s) N Seat cushion front position sensor failure
fault Seat cushion front motor failure
B1765 DSCM Driver seat Seat fore / aft motor or position sensor circuit(s) fault N Seat forward / rearward position sensor failure
Seat forward / rearward motor failure
CUSTOMER SYMPTOM: Seat forward / rearward
memory set inoperative; seat forward / rearward
function inoperative
B1769 DSCM Driver seat Seat recline motor or position sensor circuit(s) fault N Seat recline position sensor failure
Seat recline motor failure
CUSTOMER SYMPTOM: Seat recline memory set
inoperative; seat recline function inoperative
B1794 GECM Exterior lighting: front Headlamp dip beam circuit(s) fault N Headlamp bulb failure
GECM to headlamp dip beam bulbs circuit(s) (FH60-7, FH60-8): open
circuit, short circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Headlamp dip beam(s)
inoperative; headlamp dip beam(s) always on Headlamp unit failure
B1844 CTCM Cellular telephone Handset push button stuck active N Cellular telephone handset failure
B1869 RCM SRS Airbag Airbag MIL circuit open circuit Y RCM to instrument pack warning MIL circuit (CA114-20) open circuit
B1870 RCM SRS Airbag Airbag MIL circuit short circuit Y RCM to instrument pack warning MIL circuit (CA114-20) short circuit to B+
voltage
B1874 VECM Telephone with voice control and Telephone hand set not detected N Telephone hand set disconnected
vehicle emergency message VECM to telephone hand set harness open circuit fault
system (VEMS)
CUSTOMER SYMPTOM: VEMS inoperative
B1875 INST Exterior lighting: front Turn signals / hazard switch circuit fault N Instrument pack to turn signals / hazard switch circuit (FC15-20): short
circuit to ground, short circuit to B+ voltage
Turn signals and / or hazard switch failure
CUSTOMER SYMPTOM: Turn signals and hazard
warning inoperative
B1877 RCM SRS Airbag Driver seat belt pretensioner circuit open circuit Y RCM to pretensioner circuit(s) (CA114-18, CA114-22) open circuit
B1878 RCM SRS Airbag Driver seat belt pretensioner circuit short circuit to B+ Y RCM to pretensioner circuit(s) (CA114-18, CA114-22) short circuit to B+
voltage voltage
B1879 RCM SRS Airbag Driver seat belt pretensioner circuit short circuit to Y RCM to pretensioner circuit(s) (CA114-18, CA114-22) short circuit to
ground ground
B1881 RCM SRS Airbag Passenger seat belt pretensioner circuit open circuit Y RCM to pretensioner circuit(s) (CA114-15, CA114-16) open circuit
B1882 RCM SRS Airbag Passenger seat belt pretensioner circuit short circuit to Y RCM to pretensioner circuit(s) (CA114-15, CA114-16) short circuit to B+
B+ voltage voltage
B1883 RCM SRS Airbag Passenger seat belt pretensioner circuit short circuit to Y RCM to pretensioner circuit(s) (CA114-15, CA114-16) short circuit to
ground ground
B1885 RCM SRS Airbag Driver seat belt pretensioner circuit resistance fault Y Pretensioner shorting bar making contact while connector is mated
Pretensioner failure
B1886 RCM SRS Airbag Passenger seat belt pretensioner circuit resistance fault Y Pretensioner shorting bar making contact while connector is mated
Pretensioner failure
B1887 RCM SRS Airbag Driver air bag circuit short circuit to ground Y RCM to airbag circuit(s) (CA114-3, CA114-4) short circuit to ground
B1888 RCM SRS Airbag Passenger air bag circuit short circuit to ground Y RCM to airbag circuit(s) (CA114-6, CA114-7) short circuit to ground
B1891 RCM SRS Airbag Airbag audible warning circuit short circuit to B+ voltage Y RCM to instrument pack warning MIL circuit (CA114-26) short circuit to B+
voltage
B1892 RCM SRS Airbag Airbag MIL circuit fault Y RCM to instrument pack warning MIL circuit (CA114-26) open circuit, short
circuit to ground
B1893 VECM Telephone with voice control and VEMS GPS antenna circuit open circuit N VECM to antenna circuit open circuit
vehicle emergency message VEMS GPS antenna failure
system (VEMS)
CUSTOMER SYMPTOM: VEMS unable to determine
position
B1916 RCM SRS Airbag Driver air bag circuit short circuit to B+ voltage Y RCM to airbag circuit(s) (CA114-3, CA114-4) short circuit to B+ voltage
B1921 RCM SRS Airbag RCM case bracket ground fault Y Clean / repair case bracket ground
RCM failure
B1925 RCM SRS Airbag Passenger air bag circuit short circuit to B+ voltage Y RCM to airbag circuit(s) (CA114-6, CA114-7) short circuit to B+ voltage
B1932 RCM SRS Airbag Driver air bag circuit open circuit Y RCM to airbag circuit(s) (CA114-3, CA114-4) open circuit
B1933 RCM SRS Airbag Passenger air bag circuit open circuit Y RCM to airbag circuit(s) (CA114-6, CA114-7) open circuit
B1934 RCM SRS Airbag Driver airbag circuit resistance fault Y Airbag shorting bar making contact while connector is mated
Airbag failure
B1935 RCM SRS Airbag Passenger airbag circuit resistance fault Y Airbag shorting bar making contact while connector is mated
Airbag failure
B1946 A/CCM Climate control Evaporator discharge temperature sensor open circuit N Evaporator discharge temperature sensor disconnected
A/CCM to evaporator discharge temperature sensor sensing circuit
(FC28-10) open circuit
CUSTOMER SYMPTOM: Poor automatic temperature
control; no air conditioning compressor cycling control Evaporator discharge temperature sensor failure
B1947 A/CCM Climate control Evaporator discharge temperature sensor short circuit N A/CCM to evaporator discharge temperature sensor sensing circuit
to ground (FC28-10) short circuit to ground
Evaporator discharge temperature sensor failure
CUSTOMER SYMPTOM: Poor automatic temperature
control; no air conditioning compressor cycling control
B1966 A/CCM Climate control Driver discharge temperature sensor open circuit N Driver discharge temperature sensor (LH – LHD; RH – RHD) disconnected
A/CCM to driver discharge temperature sensor (LH – LHD; RH – RHD)
sensing circuit (FC28-18) open circuit
CUSTOMER SYMPTOM: Poor driver temperature
control Driver discharge temperature sensor (LH – LHD; RH – RHD) failure
B1967 A/CCM Climate control Driver discharge temperature sensor short circuit to N A/CCM to driver discharge temperature sensor (LH – LHD; RH – RHD)
ground sensing circuit (FC28-18) short circuit to ground
Driver discharge temperature sensor (LH – LHD; RH – RHD) failure
CUSTOMER SYMPTOM: Poor driver temperature
control
B1992 RCM SRS Airbag Driver side-airbag circuit short circuit to B+ voltage Y Side airbag circuit(s) (CA1-2, CA1-3) short circuit to B+ voltage
B1993 RCM SRS Airbag Driver side-airbag circuit short circuit to ground Y Side airbag circuit(s) (CA1-2, CA1-3) short circuit to ground
B1994 RCM SRS Airbag Driver side-airbag circuit open circuit Y Side airbag circuit(s) (CA1-2, CA1-3) open circuit
B1995 RCM SRS Airbag Driver side-airbag circuit resistance fault Y Side airbag shorting bar making contact while connector is mated
Side airbag failure
B1996 RCM SRS Airbag Passenger side-airbag circuit short circuit to B+ voltage Y Side airbag circuit(s) (CA1-5, CA1-6) short circuit to B+ voltage
B1997 RCM SRS Airbag Passenger side-airbag circuit short circuit to ground Y Side airbag circuit(s) (CA1-5, CA1-6) short circuit to ground
B1998 RCM SRS Airbag Passenger side-airbag circuit open circuit Y Side airbag circuit(s) (CA1-5, CA1-6) open circuit
B1999 RCM SRS Airbag Passenger side-airbag circuit resistance fault Y Side airbag shorting bar making contact while connector is mated
Side airbag failure
B2102 VECM Telephone with voice control and VEMS GPS antenna circuit short circuit N VECM to antenna circuit short circuit to ground
vehicle emergency message VEMS GPS antenna failure
system (VEMS)
CUSTOMER SYMPTOM: VEMS unable to determine
position
B2103 INST Battery; starter; generator Instrument pack passive anti-theft system (PATS) N Instrument pack to passive anti-theft system transceiver data circuit
Security module does not receive PATS transceiver data (FC15-5): open circuit, short circuit to ground, short circuit to each other,
short circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: Engine will not start Passive anti-theft system transceiver failure
B2112 DDCM Central door locking Driver door “lock / alarm set” key cylinder switch circuit N DDCM to driver door switch pack “alarm set” circuit) (DT2-16) short circuit
Security fault to ground
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver door key cylinder
switch inoperative
B2116 DDCM Central door locking Driver door “unlock / alarm reset” key cylinder switch N DDCM to driver door switch pack “alarm reset” circuit (DT2-17) short
circuit fault circuit to ground
Security
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver door key cylinder
switch inoperative
B2139 INST Battery; starter; generator Powertrain control module identification does not Y Reconfigure instrument pack using PDU
Security match instrument pack
B2141 INST Battery; starter; generator Powertrain control module identification lost from Y Reconfigure instrument pack using PDU
Security instrument pack non-volatile memory
B2141 VECM Telephone with voice control and Non-volatile memory failure N VECM failure
vehicle emergency message
system (VEMS)
CUSTOMER SYMPTOM: Telephone numbers lost;
invalid telephone numbers
B2143 DSCM Driver seat Non-volatile memory failure N Recalibrate seat memory using PDU
B2146 DSCM Driver seat Seat recline motor position out of range N Recalibrate seat memory using PDU
Seat recline position sensor circuits: open circuit, short circuit, high
resistance
CUSTOMER SYMPTOM: Seat recline memory set
inoperative; seat recline function inoperative Seat recline position sensor failure
B2149 DSCM Driver seat Seat front raise / lower motor position out of range N Recalibrate seat memory using PDU
Seat front raise / lower position sensor circuits: open circuit, short circuit,
high resistance
CUSTOMER SYMPTOM: Seat front raise / lower
memory set inoperative; seat front raise / lower Seat front raise / lower position sensor failure
function inoperative
B2152 DSCM Driver seat Seat rear raise / lower motor position out of range N Recalibrate seat memory using PDU
Seat rear raise / lower position sensor circuits: open circuit, short circuit,
high resistance
CUSTOMER SYMPTOM: Seat rear raise / lower
memory set inoperative; seat rear raise / lower function Seat rear raise / lower position sensor failure
inoperative
B2155 DSCM Driver seat Seat fore / aft motor position out of range N Recalibrate seat memory using PDU
Seat fore / aft position sensor circuits: open circuit, short circuit, high
resistance
CUSTOMER SYMPTOM: Seat fore / aft memory set
inoperative; seat fore / aft function inoperative Seat fore / aft position sensor failure
B2158 DSCM Driver seat Seat recline motor memory position out of range N Seat recline position sensor failure
DSCM failure
CUSTOMER SYMPTOM: Seat recline memory set
inoperative; seat recline function inoperative
B2161 DSCM Driver seat Seat front raise / lower motor memory position out of N Seat front raise / lower position sensor failure
range DSCM failure
B2162 INST Security Steering column locking control module identification Y Reconfigure instrument pack using PDU
does not match instrument pack
B2162 SCLCM Security Instrument pack identification does not match steering Y Reconfigure SCLCM using PDU
column locking control module
B2164 DSCM Driver seat Seat rear raise / lower motor memory position out of N Seat rear raise / lower position sensor failure
range DSCM failure
B2167 DSCM Driver seat Seat fore / aft motor memory position out of range N Seat fore / aft position sensor failure
DSCM failure
CUSTOMER SYMPTOM: Seat fore / aft memory set
inoperative; seat fore / aft function inoperative
B2168 SCLCM Security SCLCM unable to detect unlocked condition N SCLCM failure
B2169 SCLCM Security SCLCM unable to detect locked condition N SCLCM failure
B2172 RECM RECM inertia switch input Inertia switch circuit open circuit N Inertia switch tripped (vehicle impact)
Fuel pump (engine management) RECM to inertia switch circuit (CA100-8) open circuit
Central door locking Inertia switch failure
B2174 RECM Window lifts LH rear window up signal circuit fault N RECM to LH rear door switch up circuit (CA99-2) short circuit to B+ voltage
LH rear door switch failure
CUSTOMER SYMPTOM: LH rear window switch
inoperative
B2178 RECM Window lifts LH rear window down signal circuit fault N RECM to LH rear door switch down circuit (CA99-1) short circuit to B+
voltage
LH rear door switch failure
CUSTOMER SYMPTOM: LH rear window switch
inoperative
B2190 RECM Window lifts RH rear window up signal circuit fault N RECM to RH rear door switch up circuit (CA104-1) short circuit to B+
voltage
RH rear door switch failure
CUSTOMER SYMPTOM: RH rear window switch
inoperative
B2194 RECM Window lifts RH rear window down signal circuit fault N RECM to RH rear door switch down circuit (CA104-3) short circuit to B+
voltage
RH rear door switch failure
CUSTOMER SYMPTOM: RH rear window switch
inoperative
B2197 NCM Navigation Television module error N NCM to television module harness fault
Television module to monitor harness fault
Television antenna harness fault
Television module failure
B2198 NCM Navigation Traffic master module error N NCM to traffic master module harness fault
Traffic master antenna harness fault
Traffic master module failure
B2199 NCM Navigation Vehicle information control module error N NCM to vehicle information control module harness fault
Vehicle information control module antenna harness fault
Vehicle information control module failure
B2200 NCM Navigation No communication with television module N NCM to television module harness open circuit
Television module failure
B2201 NCM Navigation No communication with traffic master module N NCM to traffic master module harness open circuit
Traffic master module failure
B2202 NCM Navigation No communication with vehicle information control N NCM to vehicle information control module harness open circuit
module Vehicle information control module failure
B2204 NCM Navigation Navigation GPS antenna fault N NCM to navigation harness open circuit, short circuit, high resistance
Navigation GPS antenna failure
NCM failure
B2205 NCM Navigation NCM GPS receiver fault N NCM to navigation harness open circuit, short circuit, high resistance
Navigation GPS antenna failure
NCM failure
B2206 NCM Navigation NCM gyroscope fault N NCM incorrectly mounted in vehicle
NCM failure
B2208 NCM Navigation No communication with navigation display module N NCM to navigation display module harness open circuit
Navigation display module failure
B2214 GECM Window lifts Passenger window up signal circuit fault N GECM to passenger door switch up circuit (CA24-25) short circuit to B+
voltage
Driver door switch failure
CUSTOMER SYMPTOM: Passenger window switch
inoperative
B2215 GECM Window lifts Passenger window down signal circuit fault N GECM to passenger door switch down circuit (CA24-10) short circuit to B+
voltage
Driver door switch failure
CUSTOMER SYMPTOM: Passenger window switch
inoperative
B2312 GECM Door mirrors movement Passenger door mirror horizontal movement feedback N GECM to mirror horizontal movement feedback circuit (CA24-7): open
circuit fault circuit, short circuit to ground, short circuit to B+ voltage, high resistance
Passenger door mirror failure
CUSTOMER SYMPTOM: Passenger door mirror
horizontal movement interrupts; no horizontal memory
recall
B2316 GECM Door mirrors movement Passenger door mirror vertical movement feedback N GECM to mirror vertical movement feedback circuit (CA24-11): open
circuit fault circuit, short circuit to ground, short circuit to B+ voltage, high resistance
Passenger door mirror failure
CUSTOMER SYMPTOM: Passenger door mirror
vertical movement interrupts; no vertical memory recall
B2320 DDCM Door mirrors movement Driver door mirror horizontal movement feedback N DDCM to mirror horizontal movement feedback circuit (DT2-14): open
circuit fault circuit, high resistance
Driver door mirror failure
CUSTOMER SYMPTOM: Driver door mirror horizontal
movement interrupts; no horizontal memory recall
B2324 DDCM Door mirrors movement Driver door mirror vertical movement feedback circuit N DDCM to mirror vertical movement feedback circuit (DT2-15): open circuit,
fault high resistance
Driver door mirror failure
CUSTOMER SYMPTOM: Driver door mirror vertical
movement interrupts; no vertical memory recall
B2328 INST Steering column movement Steering column reach position feedback circuit fault N Instrument pack to column reach potentiometer feedback circuit
(FC63-21): open circuit, short circuit to ground, short circuit to B+ voltage
Column reach motor drive circuit(s): open circuit, short circuit to ground,
intermittent short circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: Steering column reach Column reach potentiometer failure
movement inoperative Column reach motor failure
B2332 INST Steering column movement Steering column tilt position feedback circuit fault N Instrument pack to column tilt potentiometer feedback circuit (FC63-20):
open circuit, short circuit to ground, short circuit to B+ voltage
Column tilt motor drive circuit(s): open circuit, short circuit to ground,
intermittent short circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: Steering column tilt Column tilt potentiometer failure
movement inoperative Column tilt motor failure
B2336 DDCM Door mirrors movement Mirror movement switches circuit(s) fault N DDCM to driver door switch pack mirror movement circuit(s); open circuit,
short circuit to ground, short circuit to each other, high resistance
Driver door switch pack ground fault
CUSTOMER SYMPTOM: Mirror movement switch(es)
inoperative Driver door switch pack failure
B2351 INST Steering column movement Steering column adjust switch circuit fault N Instrument pack to column adjust switch signal circuit (FC63-15): short
circuit to ground, short circuit to B+ voltage
Steering column adjust switch failure
CUSTOMER SYMPTOM: Steering column adjust
switch inoperative
B2373 RPACM Reverse parking aid Reverse parking aid state illumination LED circuit fault N RPACM to switch LED circuit (CA112-19) short circuit to B+ voltage
B2384 AUDIO In-car entertainment Reverse gear selected signal fault N J Gate to PCM gear selector position circuit(s): open circuit, short circuit to
ground, short circuit to B+ voltage, short circuit to each other, high
(Reverse parking aid vehicles resistance
only)
J Gate internal circuit fault
CUSTOMER SYMPTOM: Audio does not mute when
Reverse is selected; audio permanently muted SCP fault
B2385 AUDIO In-car entertainment Audio navigation mute signal fault N NCM to radio head unit mute signal circuit (FC73-16): open circuit, short
(Navigation vehicles only) circuit to ground, short circuit to B+ voltage, high resistance
NCM mute signal fault
CUSTOMER SYMPTOM: No navigation sound; audio
volume permanently reduced or muted
B2401 AUDIO In-car entertainment Audio tape deck mechanism fault N Audio tape deck mechanism failure
B2402 AUDIO In-car entertainment CD Autochanger thermal shutdown fault N CD Autochanger thermal shutdown; allow unit to cool and retest
CD Autochanger failure
CUSTOMER SYMPTOM: CD inoperative
B2404 AUDIO In-car entertainment Steering wheel switch circuit fault N Steering wheel switch(es) stuck ON
Steering wheel switch signal circuit (FC73-11): short circuit to ground,
short circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: Audio not responding to
switch commands Steering wheel switches failure
B2425 DDCM Central door locking Remote keyless entry rolling code out of N Recode key fob transmitter
Security synchronization DDCM failure
B2428 A/CCM Climate control Passenger discharge temperature sensor open circuit N Passenger discharge temperature sensor (RH – LHD; LH – RHD)
disconnected
A/CCM to passenger discharge temperature sensor (RH – LHD; LH – RHD)
CUSTOMER SYMPTOM: Poor passenger temperature sensing circuit (FC28-06) open circuit
control
Passenger discharge temperature sensor (RH – LHD; LH – RHD) failure
B2429 A/CCM Climate control Passenger discharge temperature sensor short circuit N A/CCM to passenger discharge temperature sensor (RH – LHD; LH – RHD)
to ground sensing circuit (FC28-06) short circuit to ground
Passenger discharge temperature sensor (RH – LHD; LH – RHD) failure
CUSTOMER SYMPTOM: Poor passenger temperature
control
B2431 INST Security system Key fob transmitter programming error N Reprogram key fob(s)
Key fob transmitter failure
CUSTOMER SYMPTOM: Key fob transmitter
inoperative
B2442 GECM Security Intrusion sensor / inclination sensor signal circuit fault N GECM to sensor(s) signal circuit (CA31-18): open circuit, short circuit to
ground, short circuit to B+ voltage, high resistance
Intrusion sensor(s) failure
Inclination sensor failure
B2443 GECM Automatic transmission Transmission performance mode switch circuit fault N GECM to mode switch circuit (CA31-10): open circuit, short circuit to
ground, short circuit to B+ voltage
Mode switch ground fault
CUSTOMER SYMPTOM: Mode switch inoperative Mode switch failure
B2472 INST Exterior lighting: front Fog lamp switch circuit fault N Instrument pack to lighting switch (fog lamps) circuit (FC63-13): open
Exterior lighting: rear circuit, short circuit
Lighting switch failure
CUSTOMER SYMPTOM: Fog lamp switch inoperative
B2477 ABS/TC Anti-lock braking / traction Control module incorrectly configured Y Reconfigure ABS/TCCM using PDU
control
CUSTOMER SYMPTOM: MIL flashing,
default operation
B2477 A/CCM Climate control Control module incorrectly configured N Reconfigure A/CCM using PDU
B2477 ADCM Suspension adaptive damping Control module incorrectly configured M Replace ADCM
(CATS)
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
B2477 AUDIO In-car entertainment Control module incorrectly or not configured N Reconfigure radio head unit using PDU
B2477 DSCCM Dynamic stability control Control module incorrectly configured Y Reconfigure DSCCM using PDU
B2477 INST Instrument pack Control module incorrectly configured N Reconfigure instrument pack using PDU
B2477 RCM SRS Airbag Control module incorrectly configured Y Replace RCM
B2477 RPACM Reverse parking aid Control module incorrectly configured Y Replace RPACM
B2477 VECM Telephone with voice control and Control module incorrectly configured N Reconfigure VECM using PDU
vehicle emergency message
system (VEMS)
CUSTOMER SYMPTOM: VEMS inoperative
SYSTEM The vehicle system the DTC is associated with. Refer to the applicable Electrical Guide Figure for circuit details.
FAULT DESCRIPTION Fault description. If available, customer symptom (complaint) information is provided in this column.
REFERENCE: It is recommended that the applicable “Electrical Guide” be referenced when using the information contained in this document.
B1201 RECM Instrumentation Fuel level sensor circuit(s) fault N CA101 RECM to fuel level sensor circuit(s): open circuit, short circuit to ground,
-15 short circuit to B+ voltage, short circuit to each other, high resistance
-16 Fuel level sensor(s) failure
CUSTOMER SYMPTOM: Inaccurate fuel level
B1202 IC Instrumentation Fuel level sensor circuit fault N — Fuel level sensor(s) circuit(s): open circuit
Fuel level sensor SCP message error
Fuel level sensor(s) failure
B1204 IC Instrumentation Fuel level sensor circuit fault N — Fuel level sensor(s) circuit(s): short circuit to ground
Fuel level sensor SCP message error
Fuel level sensor(s) failure
B1213 IC Security Less than two (2) keys are programmed N — Program at least two keys using WDS
B1231 DSCCM Dynamic Stability Control Longitudinal acceleration threshold exceeded Y — Brake booster vacuum low
(monitored by Adaptive M Brake booster failure
Speed Control System) Brake pressure sensor failure
Brake hydraulic unit failure
Adaptive speed control control module failure
B1231 RCM Advanced restraint system Crash data memory full Y – Replace RCM
Flash code 13
B1238 AUDIO In Car Entertainment CD autochangr over-temperature fault N — Switch OFF CD autochanger. Load CD autochanger and play media to
check for reoccurrence.
CD autochanger failure
B1242 A/CCM Climate Control Fresh / recirculation air flow actuator motor drive N FC40 A/CCM to actuator drive circuit(s): high resistance, open circuit, short
circuit fault -09 circuit to ground, or short circuit to each other
-10 Fresh / recirculation air flow actuator position sensor supply voltage
-15 circuit: open circuit, short circuit to ground or B+ voltage
FC27 Fresh / recirculation air flow actuator position sensor signal circuit: open
-09 circuit, short circuit to ground
-10 Fresh / recirculation air flow actuator failure
-15
FC41
-11
-22
FC28
CUSTOMER SYMPTOM: No variable air flow -11
direction control -22
B1251 A/CCM Climate Control In-car temperature sensor circuit open circuit N FC41 In-car temperature sensor disconnected
-09 A/CCM to in-car temperature sensor sensing circuit: open circuit
CUSTOMER SYMPTOM: No automatic FC28 In-car temperature sensor failure
temperature control -09
B1253 A/CCM Climate Control In-car temperature sensor circuit short circuit to N FC41 A/CCM to in-car temperature sensor sensing circuit: short circuit to
ground -09 ground
FC28 In-car temperature sensor failure
CUSTOMER SYMPTOM: No automatic -09
temperature control
B1255 A/CCM Climate Control Ambient air temperature sensor circuit open circuit N FC41 Ambient air temperature sensor disconnected
-17 A/CCM to ambient air temperature sensor sensing circuit: open circuit
CUSTOMER SYMPTOM: Inaccurate exterior FC28 Ambient air temperature sensor failure
temperature displayed 17
B1257 A/CCM Climate Control Ambient air temperature sensor circuit short circuit N FC41 A/CCM to ambient air temperature sensor sensing circuit: short circuit
to ground -17 to ground
FC28 Ambient air temperature sensor failure
CUSTOMER SYMPTOM: Inaccurate exterior 17
temperature displayed
B1262 A/CCM Climate Control Defrost mode actuator motor drive circuit fault N FC40 A/CCM to actuator drive circuit(s): high resistance, open circuit, short
-01 circuit to ground, or short circuit to each other
-13 Defrost mode actuator position sensor supply voltage circuit: open
-17 circuit, short circuit to ground or B+ voltage
-26
Defrost mode actuator position sensor signal circuit: open circuit, short
FC27 circuit to ground
-01 Defrost mode actuator failure
-13
-17
-26
FC41
-22
CUSTOMER SYMPTOM: No defrost air flow FC28
direction control -22
B1263 A/CCM Climate Control Panel mode actuator motor drive circuit fault N FC40 A/CCM to actuator drive circuit(s): high resistance, open circuit, short
-03 circuit to ground, or short circuit to each other
-17 Panel mode actuator position sensor supply voltage circuit: open circuit,
-24 short circuit to ground or B+ voltage
-25
Panel mode actuator position sensor signal circuit: open circuit, short
FC27 circuit to ground
-03 Panel mode actuator failure
-17
-24
-25
FC41
-22
CUSTOMER SYMPTOM: No panel air flow FC28
direction control -22
B1264 A/CCM Climate Control Floor mode actuator motor drive circuit fault N FC40 A/CCM to actuator drive circuit(s): high resistance, open circuit, short
-16 circuit to ground, or short circuit to each other
-17 Floor mode actuator position sensor supply voltage circuit: open circuit,
-22 short circuit to ground or B+ voltage
-23
Floor mode actuator position sensor signal circuit: open circuit, short
FC27 circuit to ground
-16 Floor mode actuator failure
-17
-22
-23
FC41
-22
CUSTOMER SYMPTOM: No floor air flow direction FC28
control -22
B1265 A/CCM Climate Control Cold air bypass actuator motor drive circuit fault N FC40 A/CCM to actuator drive circuit(s): high resistance, open circuit, short
-02 circuit to ground, or short circuit to each other
-11 Cold air bypass actuator position sensor supply voltage circuit: open
-12 circuit, short circuit to ground or B+ voltage
FC27 Cold air bypass actuator position sensor signal circuit: open circuit,
-02 short circuit to ground
-11 Cold air bypass actuator failure
-12
FC41
-11
-22
FC28
CUSTOMER SYMPTOM: No bypass air flow -11
direction control -22
B1299 PACM Parking Aid Sensor power supply circuit fault N CA112 Sensor power supply circuit: short circuit to ground
-15
B1309 DDCM Central door locking Driver door lock circuit short circuit to ground N DT2 DDCM to driver door latch assembly lock circuit: short circuit to ground
-8 Driver door latch assembly failure
CUSTOMER SYMPTOM: Driver door lock switch
inoperative
B1310 RECM Central Locking Passenger door latch lock / unlock switch circuit N CA101 RECM to passenger door latch lock / unlock switch circuit: open circuit,
fault -19 short circuit to ground, short circuit to B+ voltage, short circuit to
each other, high resistance
B1317 DSCCM Dynamic Stability Control Battery voltage out of range – high Y FH103 Charging system high voltage fault
M -1 DSCCM ground fault
-16
-32
-47
B1317 EPBCM Electronic Parking Brake Battery voltage out of range – high Y CA241 Charging system high voltage fault
M -1 EPBCM ground fault
-4
B1317 IC Instrument Cluster Battery voltage out of range – high N FC14 Charging system high voltage fault
-3 DSCCM ground fault
FC15
-3
B1317 RCM Advanced restraint system Battery voltage out of range – high: >17.5 V ±1.5 V N CA114 Charging system over voltage fault
-12
B1318 DSCCM Dynamic Stability Control Battery voltage out of range – low Y FH103 Charging system low voltage fault
M -1 DSCCM battery power supply circuit(s): high resistance
-16
-32
-47
B1318 EPBCM Electronic Parking Brake Battery voltage out of range – low Y CA241 Charging system low voltage fault
M -1 EPBCM battery power supply circuit(s): high resistance
-4
B1318 HLCM Automatic Headlamp Battery voltage out of range – low N FH12 Charging system low voltage fault
Leveling -23 DSCCM ignition switched power supply circuit: high resistance
B1318 IC Instrument Cluster Battery voltage out of range – low N FC14 Charging system low voltage fault
-3 DSCCM battery power supply circuit(s): high resistance
FC15
-3
B1318 RCM Advanced restraint system Battery voltage out of range – low N CA114 Charging system low voltage fault
-12 Ignition switched power supply circuit: high resistance
B1319 GECM Interior lighting Driver door ajar switch circuit fault N CA31 GECM to driver ajar door switch circuit: open circuit, short circuit to
Central door locking -8 ground, short circuit to B+ voltage
Driver door ajar switch ground fault
Security CUSTOMER SYMPTOM – GECM systems
effected: Driver door ajar switch failure
Interior lighting – lamps inoperative or always ON
Central door locking
Security
B1327 GECM Interior lighting Passenger door ajar switch circuit fault N CA24 GECM to passenger door ajar switch circuit: open circuit, short circuit
Central door locking -15 to ground, short circuit to B+ voltage
Passenger door ajar switch ground fault
Security CUSTOMER SYMPTOM – GECM systems
effected: Passenger door ajar switch failure
Interior lighting – lamps inoperative or always on
Central door locking
Security
B1331 RECM Interior lighting Trunk ajar switch circuit fault N CA102 RECM to trunk ajar switch circuit: open circuit, short circuit to ground,
Central door locking -14 short circuit to B+ voltage
Trunk ajar switch ground fault
Security
CUSTOMER SYMPTOM – RECM systems Trunk ajar switch failure
effected:
Interior lighting – trunk lamps inoperative or always
ON
Central door locking
Security
B1341 DDCM Central door locking Driver door unlock circuit short circuit to ground N DT2 DDCM to driver door latch assembly unlock circuit: short circuit to
-9 ground
Driver door latch assembly failure
CUSTOMER SYMPTOM: Driver door lock switch
inoperative
B1342 AMP In Car Entertainment – Power Power amplifier internal fault N — Power amplifier failure
Amplifier circuits
B1342 ASCCM Adaptive Speed Control Control module failure Y — ASCCM failure
M
B1342 AUDIO In Car Entertainment Control module failure N — Audio unit failure
B1342 DDCM Driver Door Control Module DDCM internal fault N – DDCM failure
B1342 DSCCM Dynamic Stability Control Control module failure Y* — DSCCM failure
M * CHECK ENGINE MIL
B1342 EPBCM Electronic Parking Brake Control module failure Y — EPBCM failure
M
B1342 RCM Advanced restraint system RCM internal fault N – RCM failure
B1342 RECM Rear Electronic Control Control module failure N — RECM failure
Module
B1342 SCLCM Security (steering column Control module failure N — SCLCM failure
lock control module)
CUSTOMER SYMPTOM: Steering column locking
inoperative
B1352 IC Instrument Cluster Ignition “key-in” switch circuit fault N FC14 Instrument cluster to key-in switch circuit: open circuit, short circuit to
CUSTOMER SYMPTOM: Key-in audible warning -2 ground
inoperative; steering column and driver seat entry / Key-in switch failure
exit memory functions inoperative
B1438 GECM Wash / wipe system Wiper mode select switch circuit fault N CA31 GECM to wipe / wash switch wiper mode select circuit: open circuit,
-2 short circuit to ground, short circuit to B+ voltage
Wipe / wash switch failure
CUSTOMER SYMPTOM: Windshield wipers
inoperative
B1446 GECM Wash / wipe system Windshield wiper motor park sense circuit fault N FH9 GECM to wiper park switch circuit: open circuit, short circuit to ground,
-13 short circuit to B+ voltage
Wiper park switch failure
CUSTOMER SYMPTOM: Incorrect windshield
wiper operation
B1470 IC Exterior lighting: front Headlamp switch circuit fault N FC63 Instrument cluster to main lighting switch (headlamps) circuit: open
CUSTOMER SYMPTOM: Headlamp switch -13 circuit, short circuit to ground, short circuit to B+ voltage
inoperative Main lighting switch failure
B1479 GECM Wash / wipe system Washer fluid level switch circuit fault Y FH9 GECM to fluid level switch circuit: open circuit, short circuit to ground,
-15 short circuit to B+ voltage
Washer fluid level switch ground fault
CUSTOMER SYMPTOM: Low fluid MIL on or off
continuously; programmed wash / wipe inoperative Washer fluid level switch failure
B1483 RECM Exterior lighting: rear Brake (stop lamp) switch circuit fault N CA102 Brake switch battery power supply open circuit
-13 RECM to brake switch circuit open circuit, short circuit to ground, short
circuit to B+ voltage
CUSTOMER SYMPTOM: Stop lamps inoperative or
always on Brake switch failure
B1499 GECM Exterior lighting: front LH front turn signal circuit fault N FH60 LH front turn signal bulb failure
-5 GECM to LH front turn signal (headlamp unit) circuit: open circuit, short
circuit to ground
CUSTOMER SYMPTOM: LH front turn signal LH headlamp unit failure
inoperative; LH front turn signal always ON GECM failure
B1499 RECM Exterior lighting: rear LH rear turn signal circuit fault N CA63 LH rear turn signal bulb failure
-3 RECM to LH rear turn signal (tail lamp unit) circuit: open circuit, short
circuit to ground
CUSTOMER SYMPTOM: LH rear turn signal LH tail lamp unit failure
inoperative; LH rear turn signal always on RECM failure
B1501 GECM Exterior lighting: front LH front turn signal circuit B+ voltage fault N FH60 GECM to LH front turn signal (headlamp unit) circuit: short circuit to B+
-5 voltage
LH headlamp unit failure
CUSTOMER SYMPTOM: LH front turn signal
inoperative; LH front turn signal always ON GECM failure
B1501 RECM Exterior lighting: rear LH rear turn signal circuit B+ voltage fault N CA63 RECM to LH rear turn signal (tail lamp unit) circuit: short circuit to B+
-3 voltage
LH tail lamp unit failure
CUSTOMER SYMPTOM: LH rear turn signal
inoperative; LH rear turn signal always on RECM failure
B1503 GECM Exterior lighting: front RH front turn signal circuit fault N FH60 RH front turn signal bulb failure
-4 GECM to RH front turn signal (headlamp unit) circuit: open circuit, short
circuit to ground
CUSTOMER SYMPTOM: RH front turn signal RH headlamp unit failure
inoperative; RH front turn signal always ON GECM failure
B1503 RECM Exterior lighting: rear RH rear turn signal circuit fault N CA63 RH rear turn signal bulb failure
-4 RECM to RH rear turn signal (tail lamp unit) circuit: open circuit, short
circuit to ground
CUSTOMER SYMPTOM: RH rear turn signal RH tail lamp unit failure
inoperative; RH rear turn signal always on RECM failure
B1505 GECM Exterior lighting: front RH front turn signal circuit B+ voltage fault N FH60 GECM to RH front turn signal (headlamp unit) circuit: short circuit to B+
-4 voltage
RH headlamp unit failure
CUSTOMER SYMPTOM: RH front turn signal
inoperative; RH front turn signal always ON GECM failure
B1505 RECM Exterior lighting: rear RH rear turn signal circuit B+ voltage fault N CA63 RECM to RH rear turn signal (tail lamp unit) circuit: short circuit to B+
-4 voltage
RH tail lamp unit failure
CUSTOMER SYMPTOM: RH rear turn signal
inoperative; RH rear turn signal always on RECM failure
B1519 GECM Security Hood ajar switch circuit fault N FH59 GECM to hood ajar switch circuit: open circuit, short circuit to ground,
-3 short circuit to B+ voltage
Hood ajar switch ground fault
CUSTOMER SYMPTOM: Security system does not
arm; security system functions incorrectly Hood ajar switch failure
B1530 DDCM Memory functions: Memory set switch circuit fault N DD4 DDCM to driver door switch pack memory set switch circuit: short
Steering column movement -25 circuit to ground
Door mirror movement Driver door switch pack failure
CUSTOMER SYMPTOM: Memory set switch
Driver seat movement inoperative
B1534 DDCM Memory functions: Memory 1 switch circuit fault N DD4 DDCM to driver door switch pack memory 1 switch circuit: short circuit
Steering column movement -1 to ground
Door mirror movement Driver door switch pack failure
Driver seat movement CUSTOMER SYMPTOM: Memory 1 switch
inoperative
B1538 DDCM Memory functions: Memory 2 switch circuit fault N DD4 DDCM to driver door switch pack memory 2 switch circuit: short circuit
Steering column movement -11 to ground
Door mirror movement Driver door switch pack failure
CUSTOMER SYMPTOM: Memory 2 switch
Driver seat movement inoperative
B1551 GECM Central Door Locking Trunk release circuit fault N CA24 GECM to trunk release circuit: open circuit, short circuit to ground
-4 Trunk release switch ground fault
Trunk release switch failure
CUSTOMER SYMPTOM: Trunk will not release Valet switch failure
B1567 GECM Exterior lighting: front Headlamp main beam circuit(s) fault N FH60 Headlamp bulb failure
-10 GECM to headlamp main beam bulbs circuit(s): open circuit, short
-17 circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Headlamp main beam(s)
inoperative; headlamp main beam(s) always ON Headlamp unit failure
B1576 IC Exterior lighting: front Headlamp main beam switch circuit fault N FC63 Instrument cluster to main lighting switch (main beam) circuit: open
CUSTOMER SYMPTOM: Headlamp main beam -12 circuit, short circuit to ground, short circuit to B+ voltage
switch inoperative Main lighting switch failure
B1600 IC Battery; starter; generator Ignition key transponder signal is not received N FC15 Incorrect ignition key(s)
Security -4 Reconfigure instrument cluster for ignition keys using PDU
CUSTOMER SYMPTOM: Engine will not start -5
-6 Passive anti-theft system transceiver failure
B1601 IC Battery; starter; generator Instrument cluster passive anti-theft system N FC15 Reprogram instrument cluster for ignition keys using PDU
Security module (PATS) received incorrect ignition key code -4 Passive anti-theft system transceiver failure
from PATS transceiver -5
-6
CUSTOMER SYMPTOM: Engine will not start
B1602 IC Battery; starter; generator Instrument cluster passive anti-theft system N FC15 Passive anti-theft system transceiver failure
Security module (PATS) received invalid form of ignition key -4
code from PATS transceiver -5
-6
CUSTOMER SYMPTOM: Engine will not start
B1676 A/CCM Climate Control Battery voltage out of range: 9 v – 16 v N FC41 Charging system low / high voltage fault
-14
CUSTOMER SYMPTOM: No climate control FC28
operation -14
B1676 DDCM Driver Door Control Module Battery voltage out of range: 9 v – 16 v N CA85 Charging system low / high voltage fault
-11 Battery power supply circuit: high resistance
B1676 GECM Various – Battery voltage out of range: 9 v – 16 v N FC15 Charging system low / high voltage fault
see FAULT DESCRIPTION -3 Battery power supply circuit: open circuit, high resistance
CUSTOMER SYMPTOM – GECM systems
effected:
Switched system power SCP functions
Security
Interior lighting
Dimmer controlled lighting
Variable assist power steering
Passenger door mirror movement
Central door locking
B1676 RECM Rear Electronic Control Battery voltage out of range: 9 v – 16 v N CA101 Charging system low / high voltage fault
Module -3 Battery power supply circuit: high resistance
B1681 IC Battery; starter; generator Instrument cluster passive anti-theft system N FC15 Instrument cluster to passive anti-theft system transceiver circuit(s):
Security (PATS) module does not receive PATS transceiver -4 open circuit, short circuit to ground, short circuit to each other, short
signal -5 circuit to B+ voltage, high resistance
Passive anti-theft system transceiver failure
CUSTOMER SYMPTOM: Engine will not start
B1689 IC Exterior lighting: front Autolamps / exit delay switch circuit fault N FC63 Instrument cluster to main lighting switch (autolamps / exit delay)
-2 circuit: open circuit, short circuit
Main lighting switch failure
CUSTOMER SYMPTOM: Headlamp autolamp
function / exit delay function inoperative
B1794 GECM Exterior lighting: front (non Headlamp dip beam circuit(s) fault N FH60 Headlamp bulb failure
HID) -7 GECM to headlamp dip beam bulbs circuit(s): open circuit, short circuit
-8 to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Headlamp dip beam(s)
inoperative; headlamp dip beam(s) always ON Headlamp unit failure
B1869 RCM Advanced restraint system Airbag MIL circuit fault N CA114 Airbag MIL circuit: open circuit
-19
B1870 RCM Advanced restraint system Airbag MIL circuit fault Y CA114 Airbag MIL circuit: short circuit to B+ voltage
-19
B1875 IC Exterior lighting: front Turn signals / hazard switch circuit fault N FC63 Instrument cluster to turn signals / hazard switch circuit: short circuit to
-1 ground, short circuit to B+ voltage
Turn signals and / or hazard switch failure
CUSTOMER SYMPTOM: Turn signals and hazard
warning inoperative
B1884 RCM Advanced restraint system Passenger airbag deactivated indicator lamp circuit Y CA114 Passenger airbag deactivated indicator lamp circuit: open circuit, short
fault -15 circuit to ground
Flash code 18
B1890 RCM Advanced restraint system Passenger airbag deactivated indicator lamp circuit Y CA114 Passenger airbag deactivated indicator lamp circuit: short circuit to
fault -15 B+ voltage
B1891 RCM Advanced restraint system Airbag audible warning circuit fault N CA114 Airbag audible warning circuit: short circuit to B+ voltage
-22
B1892 RCM Advanced restraint system Airbag audible warning circuit fault Y CA114 Airbag audible warning circuit: open circuit, short circuit to ground
Flash code 53 -22
B1893 CPCM JaguarNet Jaguar Net GPS antenna circuit fault N CA211 Jaguar Net GPS antenna circuit: open circuit
-1
B1921 RCM Advanced restraint system RCM internal airbag diagnostic monitor ground Y – RCM mounting bracket contact: open circuit, high resistance
circuit fault
Flash code 14
B1940 DSCM Driver seat Seat memory position out of range N — Re calibrate DSCM using WDS
B1946 A/CCM Climate Control Evaporator discharge temperature sensor open N FC41 Evaporator discharge temperature sensor disconnected
circuit -10 A/CCM to evaporator discharge temperature sensor sensing circuit:
FC28 open circuit
CUSTOMER SYMPTOM: Poor automatic -10 Evaporator discharge temperature sensor failure
temperature control; no air conditioning
compressor cycling control
B1947 A/CCM Climate Control Evaporator discharge temperature sensor short N FC41 A/CCM to evaporator discharge temperature sensor sensing circuit:
circuit to ground -10 short circuit to ground
FC28 Evaporator discharge temperature sensor failure
CUSTOMER SYMPTOM: Poor automatic -10
temperature control; no air conditioning
compressor cycling control
B1966 A/CCM Climate Control Driver discharge temperature sensor open circuit N FC41 Driver discharge temperature sensor (LH – LHD; RH – RHD)
-18 disconnected
FC28 A/CCM to driver discharge temperature sensor (LH – LHD; RH – RHD)
CUSTOMER SYMPTOM: Poor driver temperature sensing circuit: open circuit
control -18
Driver discharge temperature sensor (LH – LHD; RH – RHD) failure
B1967 A/CCM Climate Control Driver discharge temperature sensor short circuit N FC41 A/CCM to driver discharge temperature sensor (LH – LHD; RH – RHD)
to ground -18 sensing circuit: short circuit to ground
FC28 Driver discharge temperature sensor (LH – LHD; RH – RHD) failure
CUSTOMER SYMPTOM: Poor driver temperature -18
control
B2004 AUDIO In Car Entertainment Audio unit media over-temperature fault N — Switch OFF audio unit and allow to cool. Switch audio unit ON, load and
play media, and check for reoccurrence.
Audio unit failure
B2102 CPCM JaguarNet Jaguar Net GPS antenna circuit fault N CA211 Jaguar Net GPS antenna circuit: short circuit
-1
B2103 CPCM Telephone Telephone antenna circuit fault N CA209 Telephone antenna circuit: high resistance, open circuit
-1
CA210
-1
B2103 IC Battery; starter; generator Instrument pack passive anti-theft system (PATS) N FC15 Instrument cluster to passive anti-theft system transceiver data circuit:
Security module does not receive PATS transceiver data -5 open circuit, short circuit to ground, short circuit to each other, short
circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: Engine will not start Passive anti-theft system transceiver failure
B2112 DDCM Central door locking Driver door “lock / alarm set” key cylinder switch N DT2 DDCM to driver door switch pack “alarm set” circuit: short circuit to
Security circuit fault -16 ground
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver door key cylinder
switch inoperative
B2116 DDCM Central door locking Driver door “unlock / alarm reset” key cylinder N DT2 DDCM to driver door switch pack “alarm reset” circuit: short circuit to
Security switch circuit fault -17 ground
Driver door switch pack failure
CUSTOMER SYMPTOM: Driver door key cylinder
switch inoperative
B2139 IC Battery; starter; generator Engine control module identification does not Y — Reconfigure instrument cluster using WDS
Security match instrument cluster
B2141 CPCM Telephone CPCM configuration failure N – Invalid telephone numbers present
Reconfigure CPCM using WDS
B2141 DSCCM Dynamic Stability Control DSCCM configuration failure Y – Reconfigure DSCCM using WDS
M
B2141 IC Battery; starter; generator Engine control module identification lost from Y — Reconfigure instrument cluster using WDS
Security instrument cluster non-volatile memory
B2146 IC Interior lighting Dimmer switch circuit fault N FC63 Dimmer switch signal circuit: open circuit, short circuit to ground, short
Dimmer-controlled lighting -16 circuit to B+ voltage, high resistance
Dimmer switch failure
CUSTOMER SYMPTOM: Both interior lighting
master switch and dimmer switch inoperative
B2147 DSCM Driver seat Driver seat switch circuit fault (one or more N All seat Driver seat switch DSCM input circuit(s): short circuit to B+ voltage
individual switches) switch Driver seat switch pack failure
DSCM
input
circuits
B2162 IC Security Steering column locking control module Y — Reconfigure instrument cluster using WDS
identification does not match instrument cluster
B2162 SCLCM Security Instrument pack identification does not match Y — Reconfigure SCLCM using WDS
steering column locking control module
B2168 SCLCM Security SCLCM unable to detect unlocked condition N — SCLCM failure
B2169 SCLCM Security SCLCM unable to detect locked condition N — SCLCM failure
B2172 RECM RECM inertia switch input Inertia switch circuit open circuit N CA100 Inertia switch tripped (vehicle impact)
Fuel pump (engine -8 RECM to inertia switch circuit: open circuit
management) Inertia switch failure
Central door locking
B2197 NCM Television Television screen module internal fault N – Television screen module failure
B2199 NCM Vehicle information control Vehicle information control module internal fault N – Vehicle information control module failure
system
B2202 NCM Navigation Vehicle information control system N – NCM configured for VICS; vehicle information control module not
communications fault installed
Reconfigure NCM using WDS
B2204 NCM Navigation GPS antenna signal not received N CA167 NCM to Navigation GPS antenna circuit: open circuit
-01
-02
B2205 NCM Navigation NCM GPS receiver fault N CA167 Navigation GPS antenna obstructed
-01 NCM to Navigation GPS antenna circuit: high resistance, open circuit,
-02 short circuit
NCM failure
B2207 DSCM Driver seat DSCM internal ROM error N — DSCM failure
B2208 NCM Navigation NCM to telematics display communication fault N CA257 NCM to telematics communication circuit: high resistance, open circuit
B2243 RECM Interior lighting Driver side rear door ajar switch circuit fault N CA101 RECM to driver side rear door ajar switch circuit: open circuit, short
Central door locking -16 circuit to ground, short circuit to B+ voltage
Driver side rear door ajar switch ground fault
Security
Driver side rear door ajar switch failure
B2245 RECM Interior lighting Passenger side rear door ajar switch circuit fault N CA101 RECM to passenger side rear door ajar switch circuit: open circuit, short
Central door locking -17 circuit to ground, short circuit to B+ voltage
Passenger side rear door ajar switch ground fault
Security
Passenger side rear door ajar switch failure
B2290 RCM Advanced restraint system Passenger seat weight sensing (Occupancy Y CA232 Passenger seat weight sensing CAN circuit fault
Classification) CAN circuit fault -17 Passenger seat weight pressure sensor circuit fault
Flash code 16 -18
Test using WDS
B2291 RCM Advanced restraint system Passenger spatial sensing (Occupancy Position) Y CA232 Passenger spatial sensing CAN circuit fault
CAN circuit fault -17 Passenger spatial sensor(s) circuit(s) fault
Flash code 17 -18
Test using WDS
B2292 RCM Advanced restraint system Seat belt pretensioner circuit fault Y CA232 Driver seat belt pretensioner circuit fault
Flash code 33 – driver side -31 Passenger seat belt pretensioner circuit fault
-32
Flash code 34 – passenger side Test using WDS
CA232
-33
-34
B2293 RCM Advanced restraint system Airbag circuit status fault Y CA114 Driver airbag circuit fault
Flash code 19 – driver side -05 Passenger air bag circuit fault
-06
Flash code 21 – passenger side Test using WDS
CA114
-13
-14
B2294 RCM Advanced restraint system Curtain airbag circuit status fault Y CA232 Driver curtain airbag circuit fault
Flash code 24 – driver side -03 Passenger curtain air bag circuit fault
-04
Flash code 25 – passenger side Test using WDS
CA232
-05
-06
B2295 RCM Advanced restraint system Side airbag circuit status fault Y CA232 Driver side airbag circuit fault
Flash code 22 – driver side -01 Passenger side air bag circuit fault
-02
Flash code 23 – passenger side Test using WDS
CA232
-21
-22
B2296 RCM Advanced restraint system Impact sensor circuit status fault Y CA232 Impact sensor circuit fault
Flash code 42 – Front impact sensor -19 Test using WDS
-20
Flash code 43 – Driver side impact sensor
CA232
Flash code 44 – Passenger side impact sensor -27
Flash code 45 – Driver rear side impact sensor -28
Flash code 46 – Passenger rear side impact sensor CA232
-29
-30
CA232
-13
-14
CA232
-15
-16
B2309 DSCM Driver seat Seat motor out of range (one or more seat motors) N All seat One or more seat motor circuits: open circuit, short circuit to ground,
motors short circuit to each other
and One or more seat position sensors signal ground circuits: open circuit,
sensors short circuit to B+ voltage
circuits
One or more seat position sensor signal circuits: open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
Seat motor(s) failure
Seat position sensor(s) failure
B2312 GECM Door mirrors movement Passenger door mirror horizontal movement sensor N CA24 GECM to mirror horizontal movement sensor signal circuit: open circuit,
signal circuit fault -7 short circuit to ground, short circuit to B+ voltage, high resistance
Passenger door mirror failure
CUSTOMER SYMPTOM: Passenger door mirror
horizontal movement interrupts; no horizontal
memory recall
B2316 GECM Door Mirrors Movement Passenger door mirror vertical movement sensor N CA24 GECM to mirror vertical movement sensor signal circuit: open circuit,
signal circuit fault -11 short circuit to ground, short circuit to B+ voltage, high resistance
Passenger door mirror failure
CUSTOMER SYMPTOM: Passenger door mirror
vertical movement interrupts; no vertical memory
recall
B2320 DDCM Door mirrors movement Driver door mirror horizontal movement feedback N DT2 DDCM to mirror horizontal movement feedback circuit: open circuit,
circuit fault -14 high resistance
Driver door mirror failure
CUSTOMER SYMPTOM: Driver door mirror
horizontal movement interrupts; no horizontal
memory recall
B2324 DDCM Door mirrors movement Driver door mirror vertical movement feedback N DT2 DDCM to mirror vertical movement feedback circuit: open circuit, high
circuit fault -15 resistance
Driver door mirror failure
CUSTOMER SYMPTOM: Driver door mirror vertical
movement interrupts; no vertical memory recall
B2328 IC Steering column movement Steering column reach position sensor circuit fault N FC15 Instrument cluster to column reach position sensor signal circuit: open
-11 circuit, short circuit to ground, short circuit to B+ voltage
-12 Column reach motor drive circuit(s): open circuit, short circuit to ground,
FC63 intermittent short circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: Steering column reach -9 Column reach position sensor failure
movement inoperative Column reach motor failure
B2332 IC Steering column movement Steering column tilt position sensor circuit fault N FC15 Instrument cluster to column tilt position sensor circuit: open circuit,
-11 short circuit to ground, short circuit to B+ voltage
-12 Column tilt motor drive circuit(s): open circuit, short circuit to ground,
FC63 intermittent short circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: Steering column tilt -20 Column tilt position sensor failure
movement inoperative Column tilt motor failure
B2336 DDCM Door mirrors movement Mirror movement switches circuit(s) fault N DD4 DDCM to driver door switch pack mirror movement circuit(s); open
-3 circuit, short circuit to ground, short circuit to each other, high
-19 resistance
CUSTOMER SYMPTOM: Mirror movement -20 Driver door switch pack ground fault
switch(es) inoperative -21
-23 Driver door switch pack failure
-24
B2351 IC Steering column movement Steering column adjust switch circuit fault N FC63 Instrument cluster to column adjust switch signal circuit: short circuit to
-17 ground, short circuit to B+ voltage
Steering column adjust switch failure
CUSTOMER SYMPTOM: Steering column adjust
switch inoperative
B2369 ASCCM Adaptive Speed Control Chime request circuit fault Y FH107 Chime request circuit: short circuit to ground
M -6
B2376 SCLCM Security Lock cycle timing invalid N Reconfigure SCLCM using WDS
SCLCM failure
B2377 SCLCM Security Unlock cycle timing invalid N — Reconfigure SCLCM using WDS
SCLCM failure
B2379 SCLCM Security SCLCM not configured N — Reconfigure SCLCM using WDS
B2401 AUDIO In Car Entertainment Audio unit tape deck fault N — Audio unit failure
B2408 AMP In Car Entertainment – Power Speaker circuit(s) fault N All One or more speaker circuits: short circuit to ground
Amplifier circuits speaker Run “Audio Speaker Cycle Command” to test which channel is
shorted.
B2425 DDCM Central door locking Remote keyless entry rolling code out of N — Recode key fob transmitter
Security synchronization DDCM failure
B2426 A/CCM Climate Control RH dual solar sensor sensing circuit open circuit FC41 Dual solar sensor disconnected
-20 A/CCM to RH dual solar sensor sensing circuit: open circuit
CUSTOMER SYMPTOM: Poor automatic FC28 Dual solar sensor failure
temperature control in high sun load conditions -20
B2427 A/CCM Climate Control RH dual solar sensor sensing circuit short circuit to FC41 A/CCM to RH dual solar sensor sensing circuit: short circuit to ground
ground -20 Dual solar sensor failure
FC28
CUSTOMER SYMPTOM: Poor automatic -20
temperature control in high sun load conditions
B2428 A/CCM Climate Control Passenger discharge temperature sensor open N FC41 Passenger discharge temperature sensor (RH – LHD; LH – RHD)
circuit -06 disconnected
FC28 A/CCM to passenger discharge temperature sensor (RH – LHD; LH –
-06 RHD) sensing circuit: open circuit
CUSTOMER SYMPTOM: Poor passenger
temperature control Passenger discharge temperature sensor (RH – LHD; LH – RHD) failure
B2429 A/CCM Climate Control Passenger discharge temperature sensor short N FC41 A/CCM to passenger discharge temperature sensor (RH – LHD; LH –
circuit to ground -06 RHD) sensing circuit: short circuit to ground
FC28 Passenger discharge temperature sensor (RH – LHD; LH – RHD) failure
CUSTOMER SYMPTOM: Poor passenger -06
temperature control
B2431 IC Security system Key fob transmitter programming error N — Reprogram key fob(s)
Key fob transmitter failure
CUSTOMER SYMPTOM: Key fob transmitter
inoperative
B2434 RCM Advanced restraint system Driver seat belt switch circuit fault Y CA232 Driver seat belt switch circuit: short circuit to ground
Flash code 51 -25
B2435 RCM Advanced restraint system Driver seat belt switch circuit fault Y CA232 Driver seat belt switch circuit: high resistance
Flash code 51 -25 Driver seat belt switch failure
B2438 RCM Advanced restraint system Passenger seat belt switch circuit fault Y CA232 Passenger seat belt switch circuit: short circuit to ground
Flash code 52 -26
B2439 RCM Advanced restraint system Passenger seat belt switch circuit fault Y CA232 Passenger seat belt switch circuit: high resistance
Flash code 52 -26 Passenger seat belt switch failure
B2472 IC Exterior lighting: front Fog lamp switch circuit fault N FC63 Instrument cluster to auxiliary lighting switch (fog lamps) circuit: open
Exterior lighting: rear -6 circuit, short circuit to ground, short circuit to B+ voltage
Auxiliary lighting switch failure
CUSTOMER SYMPTOM: Fog lamp switch
inoperative
B2477 A/CCM Climate Control Control module incorrectly configured N — Reconfigure A/CCM using WDS
B2477 ADCM Suspension adaptive Control module incorrectly configured M — Reconfigure ADCM using WDS
damping (CATS)
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
B2477 AMP In Car Entertainment – Power Power amplifier incorrectly configured N — Reconfigure power amplifier using WDS
Amplifier circuits
B2477 ASCCM Adaptive Speed Control Control module configuration failure Y — Reconfigure ASCCM using WDS
M
B2477 AUDIO In Car Entertainment Control module configuration failure N — Reconfigure AUDIO using WDS
B2477 CPCM JaguarNet CPCM JaguarNet configuration failure N – Reconfigure CPCM using WDS
B2477 EPBCM Electronic Parking Brake Control module incorrectly configured Y — Reconfigure EPBCM using WDS
M
B2477 HLCM Automatic Headlamp Control module incorrectly configured N — Reconfigure HLCM using WDS
Leveling
B2477 IC Instrument Cluster Control module incorrectly configured N — Reconfigure IC using WDS
B2477 IS Intrusion Sensor Control module incorrectly configured N — Reconfigure IS using WDS
B2477 PACM Parking Aid PACM configuration failure N – Reconfigure PACM using WDS
B2477 RCM Advanced restraint system RCM configuration failure Y – Reconfigure RCM using WDS
Flash code 54
B2477 RECM Rear Electronic Control RECM incorrectly configured N — Reconfigure RECM using WDS
Module
B2477 VACM Voice Activation Control Control module configuration error N — Reconfigure VACM using WDS
Module
B2516 A/CCM Climate Control Blower motor circuit fault N FC40 Blower motor circuit: open circuit, short circuit to ground, short circuit
-21 to B+ voltage
FC27 Blower motor failure
-21 A/CCM failure
FC41
-05
FC28
-05
B2608 HLCM Automatic Headlamp LH headlamp stepper motor drive circuits fault N FH12 LH headlamp stepper motor drive circuit(s): short circuit to ground
Leveling -16
-17
-18
-19
B2609 HLCM Automatic Headlamp LH headlamp stepper motor drive circuits fault N FH12 LH headlamp stepper motor drive circuit(s): short circuit to B+ voltage,
Leveling -16 open circuit
-17
-18
-19
B2610 HLCM Automatic Headlamp LH headlamp stepper motor drive over- N FH12 LH headlamp stepper motor failure
Leveling temperature -16
-17
-18
-19
B2611 HLCM Automatic Headlamp RH headlamp stepper motor drive circuits fault N FH12 RH headlamp stepper motor drive circuit(s): short circuit to ground
Leveling -15
-20
-21
-22
B2612 HLCM Automatic Headlamp RH headlamp stepper motor drive circuits fault N FH12 RH headlamp stepper motor drive circuit(s): short circuit to B+ voltage,
Leveling -15 open circuit
-20
-21
-22
B2613 HLCM Automatic Headlamp RH headlamp stepper motor drive over- N FH12 RH headlamp stepper motor failure
Leveling temperature -15
-20
-21
-22
B2614 HLCM Automatic Headlamp Axle sensor supply circuits fault N FH12 Front and/or rear axle sensor supply circuit(s): short circuit to ground
Leveling -10
-25
B2615 HLCM Automatic Headlamp Axle sensor supply circuits fault N FH12 Front and/or rear axle sensor supply circuit(s): short circuit to B+ voltage
Leveling -10
-25
B2616 HLCM Automatic Headlamp Front axle sensor signal circuit fault N FH12 Front axle sensor signal circuit: short circuit to high voltage, open circuit
Leveling -06
B2617 HLCM Automatic Headlamp Front axle sensor signal circuit fault N FH12 Front axle sensor signal circuit: short circuit to ground
Leveling -06
B2618 HLCM Automatic Headlamp Front axle sensor signal out of range N FH12 Front axle sensor disconnected, incorrectly installed
Leveling -06 Front axle sensor failure
B2619 HLCM Automatic Headlamp Rear axle sensor signal circuit fault N FH12 Rear axle sensor signal circuit: short circuit to high voltage, open circuit
Leveling -07
B2620 HLCM Automatic Headlamp Rear axle sensor signal circuit fault N FH12 Rear axle sensor signal circuit: short circuit to ground
Leveling -07
B2621 HLCM Automatic Headlamp Rear axle sensor signal out of range N FH12 Rear axle sensor disconnected, incorrectly installed
Leveling -07 Rear axle sensor failure
B2622 HLCM Automatic Headlamp CAN vehicle speed message error N – CAN circuit fault
Leveling CAN network fault
B2623 HLCM Automatic Headlamp CAN dip beam message error N – CAN circuit fault
Leveling CAN network fault
B2626 HLCM Automatic Headlamp HLCM not configured N – Configure HLCM using WDS
Leveling
B2633 CPCM Telephone Microphone circuit fault N CA261 Microphone circuit: open circuit
-17 Microphone failure
-18
B2636 CPCM JaguarNet SOS switch circuit fault N CA261 SOS switch circuit: short circuit to ground
-15 SOS switch failure
B2637 CPCM JaguarNet Information switch circuit fault N CA261 Information switch circuit: short circuit to ground
-31 Information switch failure
B2638 CPCM Telephone Telephone rechargeable battery fault N – Battery charging circuit fault
Incorrect battery installed
B2640 CPCM Jaguar Net Airbag deployment signal circuit fault N CA261 Airbag deployment signal circuit: open circuit
-30
B2641 CPCM Jaguar Net Airbag deployment signal circuit fault N CA261 Airbag deployment signal circuit: short circuit to B+ voltage
-30
B2642 AMP In Car Entertainment – Power Low voltage detected N CA263 Power amplifier battery supply circuit(s): intermittent open circuit, high
Amplifier circuits -3 resistance
-9 Battery / generator charging system fault
Power amplifier failure
B2642 AUDIO In Car Entertainment Low voltage detected (monitored by CD N CA267 CD autochanger battery supply circuit: intermittent open circuit, high
autochanger) -2 resistance
Battery / generator charging system fault
CD autochanger failure
B2643 AMP In Car Entertainment – Power High voltage detected N CA263 Battery / generator charging system fault
Amplifier circuits -3 Power amplifier failure
-9
B2646 NCM Television TV antenna 1 circuit fault N FC102 TV antenna 1 circuit: open circuit
B2647 NCM Television TV antenna 2 circuit fault N FC103 TV antenna 2 circuit: open circuit
B2648 NCM Television TV antenna 3 circuit fault N FC104 TV antenna 3 circuit: open circuit
B2649 NCM Television TV antenna 4 circuit fault N FC105 TV antenna 4 circuit: open circuit
B2650 NCM Television TV antenna 1 circuit fault N FC102 TV antenna 1 circuit: short circuit
B2651 NCM Television TV antenna 2 circuit fault N FC103 TV antenna 2 circuit: short circuit
B2652 NCM Television TV antenna 3 circuit fault N FC104 TV antenna 3 circuit: short circuit
B2653 NCM Television TV antenna 4 circuit fault N FC105 TV antenna 4 circuit: short circuit
B2655 NCM Telematics display Telematics display internal fault N – Telematics display failure
B2691 RCM Advanced restraint system Driver seat belt switch circuit fault Y CA232 Driver seat belt switch circuit: open circuit, short circuit to B+ voltage
Flash code 51 -25
B2692 RCM Advanced restraint system Passenger seat belt switch circuit fault Y CA232 Passenger seat belt switch circuit: open circuit, short circuit to B+
Flash code 52 -26 voltage
B2736 DSCCM Dynamic Stability Control Pedal travel sensor circuit fault Y FH103 Pedal travel sensor circuit: open circuit, short circuit to ground, short
M -24 circuit to B+ voltage, short circuit to each other, high resistance
-26 Pedal travel sensor failure
-40
B2739 DSCCM Dynamic Stability Control Pedal travel sensor signal circuit fault Y FH103 Pedal travel sensor incorrectly mounted
M -40 Pedal travel sensor signal circuit: open circuit, short circuit to ground,
short circuit to B+ voltage, high resistance
Pedal travel sensor failure
Brake hydraulic unit failure
B2741 DSCCM Dynamic Stability Control Yaw rate and lateral acceleration sensors cluster Y FH103 Yaw rate and lateral acceleration sensors cluster circuit: open circuit,
circuit fault -5 short circuit to ground, short circuit to B+ voltage, short circuit to
M each other, high resistance
--7
-25 Yaw rate and lateral acceleration sensors cluster failure
-29
B2783 A/CCM Climate Control Humidity sensor short circuit to ground N FC40 A/CCM to humidity sensor sensing circuit: short circuit to ground
-04 Humidity sensor failure
FC27
-04
B2784 A/CCM Climate Control Humidity sensor open circuit N FC40 Humidity sensor disconnected
-04 A/CCM to humidity sensor sensor sensing circuit: open circuit
FC27 Humidity sensor failure
-04
B2795 A/CCM Climate Control LH dual solar sensor sensing circuit short circuit to N FC41 A/CCM to LH dual solar sensor sensing circuit: short circuit to ground
ground -07 Dual solar sensor failure
FC28
CUSTOMER SYMPTOM: Poor automatic -07
temperature control in high sun load conditions
B2796 A/CCM Climate Control LH dual solar sensor sensing circuit open circuit N FC41 Dual solar sensor disconnected
-07 A/CCM to LH dual solar sensor sensing circuit: open circuit
CUSTOMER SYMPTOM: Poor automatic FC28 Dual solar sensor failure
temperature control in high sun load conditions -07
B2888 AUDIO In Car Entertainment Audio unit media fault N — Audio unit failure
B2912 DSCCM Dynamic Stability Control Reverse gear plausibility error Y — Manual transmission reverse gear switch circuit: short circuit to ground
M Manual transmission reverse gear switch failure
Reverse gear engaged CAM message fault
Yaw rate and lateral acceleration sensors cluster failure
FAULT DESCRIPTION Fault description. If available, customer symptom (complaint) information is provided in this column.
C1095 ABS/ Anti-lock braking / traction Pressure pump circuit fault Y ABS/TCCM failure
TCCM control
CUSTOMER SYMPTOM: ABS/TC MIL warnings;
ABS/TC inoperative
C1095 DSCCM Dynamic stability control Pressure pump circuit fault Y DSCCM failure
C1145 ABS/ Anti-lock braking / traction RH front wheel speed sensor circuit fault Y ABS/TCCM to wheel speed sensor signal circuit (FH33-3): open circuit,
TCCM control short circuit to ground, short circuit to B+ voltage, high resistance
RH front wheel speed sensor failure
CUSTOMER SYMPTOM: ABS/TC MIL warnings; below
3 mph (5 km/h) system inhibited; above 3 mph (5 km/h)
the system is disabled
C1145 DSCCM Dynamic stability control RH front wheel speed sensor circuit fault Y DSCCM to wheel speed sensor signal circuit (FH51-34): open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
RH front wheel speed sensor failure
CUSTOMER SYMPTOM: DSC MIL warnings; below 3
mph (5 km/h) system inhibited; above 3 mph (5 km/h)
the system is disabled
C1155 ABS/ Anti-lock braking / traction LH front wheel speed sensor circuit fault Y ABS/TCCM to wheel speed sensor signal circuit (FH33-17): open circuit,
TCCM control short circuit to ground, short circuit to B+ voltage, high resistance
LH front wheel speed sensor failure
CUSTOMER SYMPTOM: ABS/TC MIL warnings; below
3 mph (5 km/h) system inhibited; above 3 mph (5 km/h)
the system is disabled
C1155 DSCCM Dynamic stability control LH front wheel speed sensor circuit fault Y DSCCM to wheel speed sensor signal circuit (FH51-02): open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
LH front wheel speed sensor failure
CUSTOMER SYMPTOM: DSC MIL warnings; below 3
mph (5 km/h) system inhibited; above 3 mph (5 km/h)
the system is disabled
C1165 ABS/ Anti-lock braking / traction RH rear wheel speed sensor circuit fault Y ABS/TCCM to wheel speed sensor signal circuit (FH33-7): open circuit,
TCCM control short circuit to ground, short circuit to B+ voltage, high resistance
RH rear wheel speed sensor failure
CUSTOMER SYMPTOM: ABS/TC MIL warnings; below
3 mph (5 km/h) system inhibited; above 3 mph (5 km/h)
the system is disabled
C1165 DSCCM Dynamic stability control RH rear wheel speed sensor circuit fault Y DSCCM to wheel speed sensor signal circuit (FH51-37): open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
RH rear wheel speed sensor failure
CUSTOMER SYMPTOM: DSC MIL warnings; below 3
mph (5 km/h) system inhibited; above 3 mph (5 km/h)
the system is disabled
C1175 ABS/ Anti-lock braking / traction LH rear wheel speed sensor circuit fault Y ABS/TCCM to wheel speed sensor signal circuit (FH33-21): open circuit,
TCCM control short circuit to ground, short circuit to B+ voltage, high resistance
LH rear wheel speed sensor failure
CUSTOMER SYMPTOM: ABS/TC MIL warnings; below
3 mph (5 km/h) system inhibited; above 3 mph (5 km/h)
the system is disabled
C1175 DSCCM Dynamic stability control LH rear wheel speed sensor circuit fault Y DSCCM to wheel speed sensor signal circuit (FH51-04): open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
LH rear wheel speed sensor failure
CUSTOMER SYMPTOM: DSC MIL warnings; below 3
mph (5 km/h) system inhibited; above 3 mph (5 km/h)
the system is disabled
C1233 ABS/ Anti-lock braking / traction LH front wheel speed signal fault – Y LH front wheel speed sensor failure
TCCM control detectable at vehicle speed > 12.5 mph (20 km/h)
C1233 DSCCM Dynamic stability control LH front wheel speed signal fault – Y LH front wheel speed sensor failure
detectable at vehicle speed > 12.5 mph (20 km/h)
C1234 ABS/ Anti-lock braking / traction RH front wheel speed signal fault – Y RH front wheel speed sensor failure
TCCM control detectable at vehicle speed > 12.5 mph (20 km/h)
C1234 DSCCM Dynamic stability control RH front wheel speed signal fault – Y RH front wheel speed sensor failure
detectable at vehicle speed > 12.5 mph (20 km/h)
C1235 ABS/ Anti-lock braking / traction RH rear wheel speed signal fault – Y RH rear wheel speed sensor failure
TCCM control detectable at vehicle speed > 12.5 mph (20 km/h)
C1235 DSCCM Dynamic stability control RH rear wheel speed signal fault – Y RH rear wheel speed sensor failure
detectable at vehicle speed > 12.5 mph (20 km/h)
C1236 ABS/ Anti-lock braking / traction LH rear wheel speed signal fault – Y LH rear wheel speed sensor failure
TCCM control detectable at vehicle speed > 12.5 mph (20 km/h)
C1236 DSCCM Dynamic stability control LH rear wheel speed signal fault – Y LH rear wheel speed sensor failure
detectable at vehicle speed > 12.5 mph (20 km/h)
C1277 DSCCM Dynamic stability control Steering angle rate sensor circuit fault Y DSCCM to steering angle rate sensor signal circuit(s) (FH51-14, FH51-47):
open circuit, short circuit to ground, short circuit to B+ voltage, high
resistance
Steering angle rate sensor failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1278 DSCCM Dynamic stability control Steering angle rate signal fault Y Steering angle rate sensor failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1279 DSCCM Dynamic stability control Yaw velocity sensor circuit fault Y DSCCM to yaw velocity sensor signal circuit (FH51-27): open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
Yaw velocity sensor failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1280 DSCCM Dynamic stability control Yaw velocity signal fault Y Yaw velocity sensor failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1281 DSCCM Dynamic stability control Lateral accelerometer circuit fault Y DSCCM to lateral accelerometer signal circuit (FH51-29): open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
Lateral accelerometer failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1282 DSCCM Dynamic stability control Lateral accelerometer signal fault Y Lateral accelerometer failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1283 DSCCM Dynamic stability control DSCCM active brake booster release switch test signal Y DSCCM failure
fault
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1284 GECM Instrument pack Oil pressure switch circuit fault N GECM to oil pressure switch circuit (FH59-9): open circuit, short circuit to
ground, short circuit to B+ voltage
Oil pressure switch ground fault (high resistance)
CUSTOMER SYMPTOM: Oil pressure MIL always on (if
short circuit to ground) Oil pressure switch failure
C1285 DSCCM Dynamic stability control Active brake booster solenoid drive circuit fault Y DSCCM to active brake booster solenoid drive circuit (FH51-08): open
circuit, short circuit to ground, short circuit to B+ voltage, high resistance
Active brake booster solenoid failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1286 DSCCM Dynamic stability control Active brake booster mechanical fault Y Active brake booster brake pedal fault
Active brake booster vacuum fault
Active brake booster failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1287 DSCCM Dynamic stability control Active brake booster release switch circuit fault Y DSCCM to release switch reference voltage circuit (FH51-40): open circuit,
short circuit to ground, short circuit to B+ voltage, high resistance
Active brake booster release switch failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1288 DSCCM Dynamic stability control Primary brake pressure sensor circuit fault Y DSCCM to primary brake pressure sensor sensing circuit (FH51-26): open
circuit, short circuit to ground, short circuit to B+ voltage, high resistance
DSCCM to primary brake pressure sensor reference voltage / ground
circuit(s) (FH51-10, FH51-43): open circuit, short circuit to ground, short
circuit to B+ voltage, high resistance
Primary brake pressure sensor failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1289 DSCCM Dynamic stability control Secondary brake pressure sensor circuit fault Y DSCCM to secondary brake pressure sensor sensing circuit (FH51-28):
open circuit, short circuit to ground, short circuit to B+ voltage, high
resistance
DSCCM to secondary brake pressure sensor reference voltage / ground
circuit(s) (FH51-12, FH51-45): open circuit, short circuit to ground, short
circuit to B+ voltage, high resistance
Secondary brake pressure sensor failure
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
CUSTOMER SYMPTOM: DSC MIL warnings configuration is required.
C1414 RCM SRS airbag system Incorrect control module fitted Y Replace RCM (correct part number)
C1416 ADCM Suspension adaptive damping RH front damper solenoid circuit short circuit to B+ M ADCM to RH front damper solenoid circuit(s) (CA11- 7, CA11-8): short
(CATS) voltage circuit to B+ voltage
RH front damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1417 ADCM Suspension adaptive damping RH front damper solenoid circuit short circuit ground M ADCM to RH front damper solenoid circuit(s) (CA11- 7, CA11-8): short
(CATS) circuit to ground
RH front damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1419 ADCM Suspension adaptive damping RH front damper solenoid circuit open circuit M RH front damper solenoid disconnected
(CATS) ADCM to RH front damper solenoid circuit(s) (CA11- 7, CA11-8): open
circuit
CUSTOMER SYMPTOM: Dampers default to firm;
fault message RH front damper solenoid failure
C1421 ADCM Suspension adaptive damping LH front damper solenoid circuit short circuit to B+ M ADCM to LH front damper solenoid circuit(s) (CA11- 5, CA11-6): short
(CATS) voltage circuit to B+ voltage
LH front damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1422 ADCM Suspension adaptive damping LH front damper solenoid circuit short circuit ground M ADCM to LH front damper solenoid circuit(s) (CA11- 5, CA11-6): short
(CATS) circuit to ground
LH front damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1424 ADCM Suspension adaptive damping LH front damper solenoid circuit open circuit M LH front damper solenoid disconnected
(CATS) ADCM to LH front damper solenoid circuit(s) (CA11- 5, CA11-6): open
circuit
CUSTOMER SYMPTOM: Dampers default to firm;
fault message LH front damper solenoid failure
C1425 ADCM Suspension adaptive damping RH rear damper solenoid circuit short circuit ground M ADCM to RH rear damper solenoid circuit(s) (CA11- 1, CA11-2): short
(CATS) circuit to ground
RH rear damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1426 ADCM Suspension adaptive damping RH rear damper solenoid circuit short circuit to B+ M ADCM to RH rear damper solenoid circuit(s) (CA11- 1, CA11-2): short
(CATS) voltage circuit to B+ voltage
RH rear damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1427 ADCM Suspension adaptive damping RH rear damper solenoid circuit open circuit M RH rear damper solenoid disconnected
(CATS) ADCM to RH rear damper solenoid circuit(s) (CA11- 1, CA11-2): open circuit
CUSTOMER SYMPTOM: Dampers default to firm; RH rear damper solenoid failure
fault message
C1430 ADCM Suspension adaptive damping LH rear damper solenoid circuit open circuit M LH rear damper solenoid disconnected
(CATS) ADCM to LH rear damper solenoid circuit(s) (CA11- 3, CA11-4): open circuit
CUSTOMER SYMPTOM: Dampers default to firm; LH rear damper solenoid failure
fault message
C1431 ADCM Suspension adaptive damping LH rear damper solenoid circuit short circuit to B+ M ADCM to LH rear damper solenoid circuit(s) (CA11- 3, CA11-4): short circuit
(CATS) voltage to B+ voltage
LH rear damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1432 ADCM Suspension adaptive damping LH rear damper solenoid circuit short circuit ground M ADCM to LH rear damper solenoid circuit(s) (CA11- 3, CA11-4): short circuit
(CATS) to ground
LH rear damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1435 ADCM Suspension adaptive damping Rear vertical accelerometer sensing circuit fault M Rear vertical accelerometer incorrectly oriented
(CATS) ADCM to rear vertical accelerometer sensing circuit (CA12-10): open
circuit, short circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Dampers default to firm;
fault message Rear vertical accelerometer failure
C1446 GECM Instrument pack Parking brake switch circuit fault N GECM to parking brake switch circuit (CA31-19): open circuit, short circuit
to ground, short circuit to B+ voltage
Parking brake switch ground fault (high resistance)
CUSTOMER SYMPTOM: Drive away door locking
inoperative (manual transmission vehicles) Parking brake switch failure
C1455 ADCM Suspension adaptive damping Front vertical accelerometer sensing circuit fault M Front vertical accelerometer incorrectly oriented
(CATS) ADCM to front vertical accelerometer sensing circuit (CA12-12): open
circuit, short circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Dampers default to firm;
fault message Front vertical accelerometer failure
C1515 ADCM Suspension adaptive damping Lateral accelerometer sensing circuit fault M Lateral accelerometer incorrectly oriented
(CATS) ADCM to lateral accelerometer sensing circuit (CA12-11): open circuit,
short circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Dampers default to firm;
fault message Lateral accelerometer failure
C1699 RPACM Reverse parking aid LH sensor circuit short circuit to B+ voltage Y RPACM to LH sensor sense circuit ( CA112-11): short circuit to B+ voltage
RPACM to LH sensor power supply circuit ( CA112-15): short circuit to B+
voltage
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1700 RPACM Reverse parking aid LH sensor circuit short circuit fault Y RPACM to LH sensor sense circuit ( CA112-11): open circuit, short circuit
ground
RPACM to LH sensor ground circuit ( CA112-16): open circuit, short circuit
CUSTOMER SYMPTOM: Reverse parking aid ground
inoperative
C1702 RPACM Reverse parking aid RH sensor circuit short circuit to B+ voltage Y RPACM to RH sensor sense circuit ( CA112-24): short circuit to B+ voltage
RPACM to RH sensor power supply circuit ( CA112-15): short circuit to B+
voltage
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1703 RPACM Reverse parking aid RH sensor circuit short circuit fault Y RPACM to RH sensor sense circuit ( CA112-24): open circuit, short circuit
ground
RPACM to RH sensor ground circuit ( CA112-16): open circuit, short circuit
CUSTOMER SYMPTOM: Reverse parking aid ground
inoperative
C1705 RPACM Reverse parking aid Center LH sensor circuit short circuit to B+ voltage Y RPACM to center LH sensor sense circuit ( CA112-10): short circuit to B+
voltage
RPACM to center LH sensor power supply circuit ( CA112-15): short circuit
CUSTOMER SYMPTOM: Reverse parking aid to B+ voltage
inoperative
C1706 RPACM Reverse parking aid Center LH sensor circuit short circuit fault Y RPACM to center LH sensor sense circuit ( CA112-10): open circuit, short
circuit ground
RPACM to center LH sensor ground circuit ( CA112-16): open circuit, short
CUSTOMER SYMPTOM: Reverse parking aid circuit ground
inoperative
C1707 RPACM Reverse parking aid Center LH sensor fault Y Center LH sensor failure
C1708 RPACM Reverse parking aid Center RH sensor circuit short circuit to B+ voltage Y RPACM to center RH sensor sense circuit ( CA112-23): short circuit to B+
voltage
RPACM to center RH sensor power supply circuit ( CA112-15): short circuit
CUSTOMER SYMPTOM: Reverse parking aid to B+ voltage
inoperative
C1709 RPACM Reverse parking aid Center RH sensor circuit short circuit fault Y RPACM to center RH sensor sense circuit ( CA112-23): open circuit, short
circuit ground
RPACM to center RH sensor ground circuit ( CA112-16): open circuit, short
CUSTOMER SYMPTOM: Reverse parking aid circuit ground
inoperative
C1710 RPACM Reverse parking aid Center RH sensor fault Y Center RH sensor failure
C1730 DSCCM Dynamic stability control DSCCM sensor reference voltage supply not within Y DSCCM failure
specification
NOTE: Control module calibration using PDU is required when the fault is
repaired and the DTC is cleared. MIL will flash to indicate that
configuration is required.
C1742 RPACM Reverse parking aid Parking aid sounder circuit fault Y RPACM to sounder circuit(s) (CA112-14, CA114-17): open circuit, short
circuit to ground
Parking aid sounder failure
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1743 RPACM Reverse parking aid Parking aid sounder circuit short circuit to B+ voltage Y RPACM to sounder circuit(s) (CA112-14, CA114-17): short circuit to B+
voltage
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1748 RPACM Reverse parking aid Reverse parking aid switch circuit fault N RPACM to switch circuit (CA112-7): open circuit, short circuit to ground,
short circuit to B+ voltage
Reverse parking aid switch ground fault
CUSTOMER SYMPTOM: Reverse parking aid switch
inoperative Reverse parking aid switch failure
C1805 ABS/ Anti-lock braking / traction ABS/TCCM mismatched with PCM (powertrain control Y Replace ABS/TCCM
TCCM control module)
C1805 DSCCM Dynamic stability control DSCCM mismatched with PCM (powertrain control Y Replace DSCCM (correct part number)
module)
C1920 RPACM Reverse parking aid Reverse parking aid state illumination circuit fault N/Y RPACM to switch STATE LED circuit (CA112-19): open circuit, short circuit
to ground
Reverse parking aid switch ground fault
CUSTOMER SYMPTOM: Reverse parking aid
inoperative Reverse parking aid switch failure
C1924 ADCM Variable assist steering Variable assist steering actuator circuit fault N GECM to variable assist steering actuator circuit FH60-9: open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
Variable assist steering actuator failure
CUSTOMER SYMPTOM: “Steering feel” incorrect
C1925 ADCM Variable assist steering Variable assist steering actuator circuit fault N GECM to variable assist steering actuator circuit FH60-2: open circuit, short
circuit to ground, short circuit to B+ voltage, high resistance
Variable assist steering actuator failure
CUSTOMER SYMPTOM: “Steering feel” incorrect
C1960 DSCCM Dynamic stability control Brake switch circuit fault (RECM brake switch message Y DSCCM to brake switch circuit: open circuit, short circuit to ground, short
does not agree with DSCCM brake switch message) circuit to B+ voltage, high resistance
RECM to brake switch circuit: open circuit, short circuit to ground, short
circuit to B+ voltage, high resistance
CUSTOMER SYMPTOM: DSC MIL warnings
SYSTEM The vehicle system the DTC is associated with. Refer to the applicable Electrical Guide Figure for circuit details.
FAULT DESCRIPTION Fault description. If available, customer symptom (complaint) information is provided in this column.
REFERENCE: It is recommended that the applicable “Electrical Guide” be referenced when using the information contained in this document.
C1093 DSCCM Dynamic Stability Control Traction control switch circuit fault N FH103 Traction control switch circuit fault:
-38 open circuit, short circuit to B+ voltage, short circuit to ground
Traction control switch failure
C1094 EPBCM Electronic Parking Brake Parking brake apply switch circuit fault Y CA242 Parking brake apply switch circuit:
M -5 open circuit, short circuit to B+ voltage
-12
C1095 DSCCM Dynamic Stability Control DSCCM pump failure Y FH103 Pump B+ power supply circuit: open circuit, short circuit to ground
M -1 Pump ground circuit: open circuit, high resistance
-47
DSCCM failure
C1132 EPBCM Electronic Parking Brake Clutch pedal position sensor signal circuit fault N CA242 Clutch pedal position sensor signal circuit: short circuit to ground
-11
C1133 EPBCM Electronic Parking Brake Clutch pedal position sensor signal circuit fault N CA242 Clutch pedal position sensor signal circuit: short circuit to B+ voltage
-11
C1134 EPBCM Electronic Parking Brake In-gear switch circuit fault N CA242 In-gear switch circuit: short circuit to ground
-3
C1135 EPBCM Electronic Parking Brake In-gear switch circuit fault Y CA242 In-gear switch circuit: short circuit to B+ voltage
M -3
C1141 DSCCM Dynamic Stability Control LH front wheel speed sensor mechanical fault Y — LH front wheel speed sensor reluctor tooth (teeth) missing or damaged
M
C1142 DSCCM Dynamic Stability Control RH front wheel speed sensor mechanical fault Y — RH front wheel speed sensor reluctor tooth (teeth) missing or damaged
M
C1143 DSCCM Dynamic Stability Control LH rear wheel speed sensor mechanical fault Y — LH rear wheel speed sensor reluctor tooth (teeth) missing or damaged
M
C1144 DSCCM Dynamic Stability Control RH rear wheel speed sensor mechanical fault Y — RH rear wheel speed sensor reluctor tooth (teeth) missing or damaged
M
C1145 DSCCM Dynamic Stability Control RH front wheel speed sensor circuit fault Y* FH103 RH front wheel speed sensor circuit: open circuit, short circuit to B+
M -33 voltage, short circuit to ground, high resistance
-34 RH front wheel speed sensor failure
*CHECK ENGINE MIL
C1155 DSCCM Dynamic Stability Control LH front wheel speed sensor circuit fault Y* FH103 LH front wheel speed sensor circuit: open circuit, short circuit to B+
M -45 voltage, short circuit to ground, high resistance
-46 LH front wheel speed sensor failure
*CHECK ENGINE MIL
C1165 DSCCM Dynamic Stability Control RH rear wheel speed sensor circuit fault Y* FH103 RH rear wheel speed sensor circuit: open circuit, short circuit to B+
M -42 voltage, short circuit to ground, high resistance
-43 RH rear wheel speed sensor failure
*CHECK ENGINE MIL
C1175 DSCCM Dynamic Stability Control LH rear wheel speed sensor circuit fault Y* FH103 LH rear wheel speed sensor circuit: open circuit, short circuit to B+
M -36 voltage, short circuit to ground, high resistance
-37 LH rear wheel speed sensor failure
*CHECK ENGINE MIL
C1223 DSCCM Dynamic Stability Control LH front wheel speed sensor signal missing Y FH103 LH front wheel speed sensor air gap too large
M -45 LH front wheel speed sensor reluctor mechanical damage
LH front wheel speed sensor signal circuit: high resistance
LH front wheel speed sensor failure
C1234 DSCCM Dynamic Stability Control RH front wheel speed sensor signal missing Y FH103 RH front wheel speed sensor air gap too large
M -34 RH front wheel speed sensor reluctor mechanical damage
RH front wheel speed sensor signal circuit: high resistance
RH front wheel speed sensor failure
C1235 DSCCM Dynamic Stability Control LH rear wheel speed sensor signal missing Y FH103 LH rear wheel speed sensor air gap too large
M -43 LH rear wheel speed sensor reluctor mechanical damage
LH rear wheel speed sensor signal circuit: high resistance
LH rear wheel speed sensor failure
C1236 DSCCM Dynamic Stability Control RH rear wheel speed sensor signal missing Y FH103 RH rear wheel speed sensor air gap too large
M -36 RH rear wheel speed sensor reluctor mechanical damage
RH rear wheel speed sensor signal circuit: high resistance
RH rear wheel speed sensor failure
C1267 DSCCM Dynamic Stability Control DSCCM anti-lock functions temporarily disabled Y — DSCCM failure
M Note: attempt hard reset before DSCCM replacement
C1277 DSCCM Dynamic Stability Control Steering angle sensor circuit(s) fault Y FH103 Steering angle sensor circuit(s): open circuit, intermittent open circuit,
M -3 short circuit to B+ voltage, short circuit to ground, high resistance
-5 Steering angle sensor incorrectly mounted
-6
-7 Steering angle sensor loose
Steering angle sensor failure
C1279 DSCCM Dynamic Stability Control Yaw rate sensor circuit(s) fault Y FH103 Yaw rate and lateral acceleration sensors cluster circuit(s):
-5 open circuit, intermittent open circuit, short circuit to B+ voltage,
M short circuit to ground, high resistance
-7
-25 Yaw rate sensor failure
-29
C1280 DSCCM Dynamic Stability Control Yaw rate sensor signal fault Y FH103 Yaw rate and lateral acceleration sensors cluster incorrectly mounted
M -25 Yaw rate and lateral acceleration sensors cluster loose
-29
Yaw rate and lateral acceleration sensors cluster failure
C1281 DSCCM Dynamic Stability Control Lateral acceleration sensor circuit(s) fault Y FH103 Yaw rate and lateral acceleration sensors cluster circuit(s):
-5 open circuit, intermittent open circuit, short circuit to B+ voltage,
M short circuit to ground, high resistance
-7
-25 Lateral acceleration sensor failure
-29
C1282 DSCCM Dynamic Stability Control Lateral acceleration sensor signal fault Y FH103 Yaw rate and lateral acceleration sensors cluster incorrectly mounted
M -25 Yaw rate and lateral acceleration sensors cluster loose
-29
Yaw rate and lateral acceleration sensors cluster failure
C1284 GECM Instrumentation Oil pressure switch circuit fault N FH59 GECM to oil pressure switch circuit:
-9 open circuit, short circuit to ground, short circuit to B+ voltage
Oil pressure switch ground fault (high resistance)
CUSTOMER SYMPTOM: Oil pressure MIL always
on (if short circuit to ground) Oil pressure switch failure
C1285 DSCCM Dynamic Stability Control Booster solenoid circuit fault Y FH103 Booster solenoid circuit: open circuit, short circuit to ground
M -17 Booster solenoid failure
-31
C1286 DSCCM Dynamic Stability Control Active brake booster mechanical failure Y FH103 Booster force switch circuit: open circuit, short circuit to ground
M -27 Booster force switch failure
-28
-30 DSCCM failure
Active brake booster mechanical failure
C1287 DSCCM Dynamic Stability Control Booster force switch circuit fault Y FH103 Booster force switch circuit:
M -27 open circuit, short circuit to ground, short circuit to B+ voltage
-28 Booster force switch failure
-30
C1288 DSCCM Dynamic Stability Control Brake pressure sensor circuit fault Y FH103 Brake pressure sensor circuit:
M -18 open circuit, short circuit to ground, short circuit to B+ voltage
-19 Brake pressure sensor failure
-20
C1291 ASCCM Adaptive Speed Control ASCCM sensor temperature out of range Y — ASCCM sensor too warm or too cold
M Normal operating temperature: -40 °C – 70 °C (-40 °F – 158 °F)
C1292 ASCCM Adaptive Speed Control ASCCM sensor blocked Y — Remove blockage from front of sensor
M
C1293 ASCCM Adaptive Speed Control ASCCM sensor alignment out of range Y — ASCCM sensor alignment incorrect
M Mechanically realign sensor
Perform complete service alignment
C1294 ASCCM Adaptive Speed Control Active speed or vehicle speed out of range Y — Other control module (ECM, DSCCM, IC, TCM) ASC speed related fault
M ASCCM failure
C1295 DSCCM Dynamic Stability Control Steering angle sensor circuit fault Y FH103 Steering angle sensor circuit(s): open circuit, intermittent open circuit,
M -3 short circuit to B+ voltage, short circuit to ground, high resistance
-5 Steering angle sensor failure
-6
-7
C1306 DSCCM Dynamic Stability Control Steering angle sensor initialization failed Y — Steering angle sensor encoder ring incorrectly installed
M Steering angle sensor encoder ring loose
Steering angle sensor encoder ring mechanical failure
C1307 DSCCM Dynamic Stability Control Steering angle sensor encoder ring fault Y FH103 Steering angle sensor encoder ring incorrectly installed
M -3 Steering angle sensor encoder ring loose
-6
Steering angle sensor encoder ring mechanical failure
Steering angle sensor signal circuit: short circuit to each other
Steering angle sensor failure
C1414 RCM Advanced Restraint System Incorrect control module fitted Y — Replace RCM (correct part number)
C1416 ADCM Suspension Adaptive RH front damper solenoid circuit short circuit to B+ M CA11 ADCM to RH front damper solenoid circuit(s):
Damping (CATS) voltage -7 short circuit to B+ voltage
-8 RH front damper solenoid failure
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1417 ADCM Suspension Adaptive RH front damper solenoid circuit short circuit M CA11 ADCM to RH front damper solenoid circuit(s): short circuit to ground
Damping (CATS) ground -7 RH front damper solenoid failure
-8
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1419 ADCM Suspension Adaptive RH front damper solenoid circuit open circuit M CA11 RH front damper solenoid disconnected
Damping (CATS) -7 ADCM to RH front damper solenoid circuit(s): open circuit
-8
CUSTOMER SYMPTOM: Dampers default to firm; RH front damper solenoid failure
fault message
C1421 ADCM Suspension Adaptive LH front damper solenoid circuit short circuit to B+ M CA11 ADCM to LH front damper solenoid circuit(s): short circuit to B+ voltage
Damping (CATS) voltage -5 LH front damper solenoid failure
-6
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1422 ADCM Suspension Adaptive LH front damper solenoid circuit short circuit M CA11 ADCM to LH front damper solenoid circuit(s): short circuit to ground
Damping (CATS) ground -5 LH front damper solenoid failure
-6
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1424 ADCM Suspension Adaptive LH front damper solenoid circuit open circuit M CA11 LH front damper solenoid disconnected
Damping (CATS) -5 ADCM to LH front damper solenoid circuit(s): open circuit
-6
CUSTOMER SYMPTOM: Dampers default to firm; LH front damper solenoid failure
fault message
C1425 ADCM Suspension Adaptive RH rear damper solenoid circuit short circuit ground M CA11 ADCM to RH rear damper solenoid circuit(s): short circuit to ground
Damping (CATS) -1 RH rear damper solenoid failure
-2
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1426 ADCM Suspension Adaptive RH rear damper solenoid circuit short circuit to B+ M CA11 ADCM to RH rear damper solenoid circuit(s): short circuit to B+ voltage
Damping (CATS) voltage -1 RH rear damper solenoid failure
-2
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1427 ADCM Suspension Adaptive RH rear damper solenoid circuit open circuit M CA11 RH rear damper solenoid disconnected
Damping (CATS) -1 ADCM to RH rear damper solenoid circuit(s): open circuit
-2
CUSTOMER SYMPTOM: Dampers default to firm; RH rear damper solenoid failure
fault message
C1430 ADCM Suspension Adaptive LH rear damper solenoid circuit open circuit M CA11 LH rear damper solenoid disconnected
Damping (CATS) -3 ADCM to LH rear damper solenoid circuit(s): open circuit
-4
CUSTOMER SYMPTOM: Dampers default to firm; LH rear damper solenoid failure
fault message
C1431 ADCM Suspension Adaptive LH rear damper solenoid circuit short circuit to B+ M CA11 ADCM to LH rear damper solenoid circuit(s): short circuit to B+ voltage
Damping (CATS) voltage -3 LH rear damper solenoid failure
-4
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1432 ADCM Suspension Adaptive LH rear damper solenoid circuit short circuit ground M CA11 ADCM to LH rear damper solenoid circuit(s): short circuit to ground
Damping (CATS) -3 LH rear damper solenoid failure
-4
CUSTOMER SYMPTOM: Dampers default to firm;
fault message
C1435 ADCM Suspension Adaptive Rear vertical accelerometer sensing circuit fault M CA12 Rear vertical accelerometer incorrectly oriented
Damping (CATS) -10 ADCM to rear vertical accelerometer sensing circuit:
open circuit, short circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Dampers default to firm;
fault message Rear vertical accelerometer failure
C1440 DSCCM Dynamic Stability Control Brake pressure sensor signal circuit fault Y FH103 Brake pressure sensor signal circuit:
M -20 open circuit, short circuit to B+ voltage, short circuit to ground
Brake pressure sensor failure
C1446 DSCCM Dynamic Stability Control Stop lamp circuit fault (CAN message) Y FH103 Brake ON / OFF switch circuit fault
M -11 Brake ON / OFF switch failure
-12
-14 Brake ON / OFF switch CAN message fault
-15
C1455 ADCM Suspension Adaptive Front vertical accelerometer sensing circuit fault M CA12 Front vertical accelerometer incorrectly oriented
Damping (CATS) -12 ADCM to front vertical accelerometer sensing circuit:
open circuit, short circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Dampers default to firm;
fault message Front vertical accelerometer failure
C1459 ASCCM Adaptive Speed Control Forward alert switch and ASC indicator circuit fault Y FH107 Forward alert switch and ASC indicator circuit:
M -12 open circuit, short circuit to B+ voltage
C1515 ADCM Suspension Adaptive Lateral accelerometer sensing circuit fault M CA12 Lateral accelerometer incorrectly oriented
Damping (CATS) -11 ADCM to lateral accelerometer sensing circuit:
open circuit, short circuit to ground, short circuit to B+ voltage
CUSTOMER SYMPTOM: Dampers default to firm;
fault message Lateral accelerometer failure
C1699 PACM Parking Aid LH sensor data circuit short circuit to B+ voltage Y CA112 LH sensor data circuit: short circuit to B+ voltage
-11
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1700 PACM Parking Aid LH sensor data circuit fault Y CA112 LH sensor data circuit: open circuit, short circuit ground
-11
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1702 PACM Parking Aid RH sensor data circuit short circuit to B+ voltage Y CA112 RH sensor data circuit: short circuit to B+ voltage
-24
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1703 PACM Parking Aid RH sensor data circuit fault Y CA112 RH sensor data circuit: open circuit, short circuit ground
-24
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1705 PACM Parking Aid LH center sensor data circuit short circuit to B+ Y CA112 LH center sensor data circuit: short circuit to B+ voltage
voltage -10
C1706 PACM Parking Aid LH center sensor data circuit fault Y CA112 LH center sensor data circuit: open circuit, short circuit ground
-10
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1707 PACM Parking Aid LH center sensor fault Y — LH center sensor failure
C1708 PACM Parking Aid RH center sensor data circuit short circuit to B+ Y CA112 RH center sensor data circuit: short circuit to B+ voltage
voltage -23
C1709 PACM Parking Aid RH center sensor data circuit fault Y CA112 RH center sensor data circuit: open circuit, short circuit ground
-23
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1710 PACM Parking Aid RH center sensor fault Y — RH center sensor failure
C1730 DSCCM Dynamic Stability Control Sensor signal supply voltage (nominal 5 V) out of Y FH103 Sensor supply voltage circuit(s):
range -7 short circuit to ground, short circuit to B+ voltage
M
-18 DSC sensor(s) failure: brake pressure sensor, steering angle sensor,
-26 yaw rate and lateral acceleration sensor cluster, active brake booster
-27 force switch, pedal travel sensor
-30 DSCCM failure
C1742 PACM Parking Aid Parking aid sounder circuit fault Y CA112 PACM to sounder circuit(s): open circuit, short circuit to ground
-14 Parking aid sounder failure
-17
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1743 PACM Parking Aid Parking aid sounder circuit short circuit to B+ Y CA112 PACM to sounder circuit(s): short circuit to B+ voltage
voltage -14
-17
CUSTOMER SYMPTOM: Reverse parking aid
inoperative
C1748 ASCCM Adaptive Speed Control Forward alert switch and ASC indicator circuit fault Y FH107 Forward alert switch and ASC indicator circuit: short circuit to ground
M -12
C1769 EPBCM Electronic Parking Brake Parking brake apply switch circuit fault Y CA242 Parking brake apply switch circuit: short circuit to ground
M -5
-12
C1777 DSCCM Dynamic Stability Control DSCCM internal vacuum pressure circuit fault Y — DSCCM failure
M Active brake booster failure
C1782 EPBCM Electronic Parking Brake Parking brake release switch circuit fault Y CA242 Parking brake release switch circuit:
M -6 open circuit, short circuit to B+ voltage
-12
C1783 EPBCM Electronic Parking Brake Parking brake release switch circuit fault Y CA242 Parking brake release switch circuit: short circuit to ground
M -6
-12
C1784 EPBCM Electronic Parking Brake Parking brake drive circuit(s) fault Y CA41 Parking brake drive circuit(s):
M -2 short circuit to ground, short circuit to each other
-3
C1785 EPBCM Electronic Parking Brake Parking brake drive circuit(s) fault Y CA41 Parking brake drive circuit(s): open circuit
M -2
-3
C1786 EPBCM Electronic Parking Brake Parking brake motor internal fault Y — Parking brake motor failure
M
C1799 EPBCM Electronic Parking Brake Parking brake motor position sensor circuit fault Y CA242 Parking brake motor position sensor circuit(s): open circuit, short circuit
M -4 to ground, short circuit to B+ voltage, high resistance
-10 Parking brake motor position sensor failure (parking brake motor failure)
-12
C1801 EPBCM Electronic Parking Brake Motor current level / position conflict – apply Y — Parking brake motor failure
M
C1802 EPBCM Electronic Parking Brake Motor current level / position conflict – apply Y — Parking brake motor failure
M
C1803 EPBCM Electronic Parking Brake Motor current level / position conflict – release Y — Parking brake motor failure
M
C1924 GECM Variable assist steering Variable assist steering actuator circuit fault N FH60 GECM to variable assist steering actuator circuit: short circuit to ground
-9 Variable assist steering actuator failure
CUSTOMER SYMPTOM: “Steering feel” incorrect
C1925 GECM Variable assist steering Variable assist steering actuator circuit fault N FH60 GECM to variable assist steering actuator circuit: open circuit,
-2 short circuit to ground, short circuit to B+ voltage, high resistance
Variable assist steering actuator failure
CUSTOMER SYMPTOM: “Steering feel” incorrect
C1935 ASCCM Adaptive Speed Control Chime request circuit fault Y FH107 Chime request circuit: open circuit, short circuit to B+ voltage
M -6
C1947 RCM Advanced Restraint System Driver seat position switch circuit fault Y CA232 Driver seat position switch circuit(s): short circuit to ground
Flash code 49 -23
-24
C1948 RCM Advanced Restraint System Driver seat position switch circuit fault Y CA232 Driver seat position switch circuit(s): high resistance
Flash code 49 -23 Driver seat position switch failure
-24
C1977 AUDIO In Car Entertainment Steering wheel audio switch circuit fault N FC94 Steering wheel audio switch circuit: short circuit to ground
-18
C1981 RCM Advanced Restraint System Driver seat position switch circuit fault Y CA232 Driver seat position switch circuit(s):
Flash code 49 -23 open circuit, short circuit to B+ voltage
-24 Driver seat position switch failure
C1989 EPBCM Electronic Parking Brake Parking brake apply and release switches Y CA242 Parking brake apply and release switch circuits:
simultaneously activated M -5 short circuit to each other
-6 Electronic parking brake switch failure
-12
C1994 DSCCM Dynamic Stability Control Yaw control failure Y FH103 Yaw rate sensor failure
M -5 DSCCM failure
-7
-25
29
C1997 DSCCM Dynamic Stability Control Pressure control failure Y FH103 Brake pressure sensor signal circuit: open circuit, short circuit to
M -17 ground, short circuit to B+ voltage, high resistance
-20 Brake pressure sensor failure
-31
Booster solenoid circuit: open circuit, short circuit to ground,
short circuit to B+ voltage, high resistance
Booster solenoid failure
Active brake booster failure
C2778 DSCCM Dynamic Stability Control Yaw rate and lateral acceleration sensors cluster Y FH103 Yaw rate and lateral acceleration sensors cluster sensor supply voltage
sensor supply voltage circuit fault M -7 circuit: open circuit, short circuit to ground, short circuit to B+ voltage.
DSCCM failure
C2783 DSCCM Dynamic Stability Control Yaw rate and lateral acceleration sensors cluster Y — Incorrect Yaw rate and lateral acceleration sensors cluster fitted
incorrect specification M
C2785 DSCCM Dynamic Stability Control DSC sensors out of calibration Y — DSCCM failure
M
SYSTEM The vehicle system the DTC is associated with. Refer to the applicable Electrical Guide Figure for circuit details.
FAULT DESCRIPTION Fault description. If available, customer symptom (complaint) information is provided in this column.
REFERENCE: It is recommended that the applicable “Electrical Guide” be referenced when using the information contained in this document.
U1260 DSCM Driver Seat SCP network SCP + circuit fault N DM43 SCP network circuit (SCP +):
-1 open circuit, short circuit to B+ voltage, short circuit to ground
SCP network fault
DSCM SCP failure
U1261 DSCM Driver Seat SCP network SCP - circuit fault N DM34 SCP network circuit (SCP -):
-12 open circuit, short circuit to B+ voltage, short circuit to ground
SCP network fault
DSCM SCP failure
U1262 AUDIO In Car Entertainment SCP network circuit fault N FC94 SCP network circuit:
-9 open circuit, short circuit to B+ voltage, short circuit to ground
-10 SCP network fault
Audio unit SCP failure
U1262 DSCM Driver Seat SCP network circuit fault N DM34 SCP network circuit:
-1 open circuit, short circuit to B+ voltage, short circuit to ground
-12 SCP network fault
DSCM SCP failure
U1341 ADCM Suspension Adaptive SCP vehicle speed message invalid or not available N CA11 Verify integrity of DSCCM
Damping -13 SCP network fault
-14
U1900 A/CCM Climate Control CAN communication fault N FC41 CAN circuit:
-1 open circuit, short circuit to B+ voltage, short circuit to ground
-12 A/CCM internal CAN fault
FC28 CAN network fault
-1
-12
U1901 DSCCM Dynamic Stability Control Local CAN network (steering angle sensor, N FH103 Local CAN circuit:
yaw rate and lateral acceleration sensor) -25 open circuit, short circuit to B+ voltage, short circuit to ground
communication fault -29 DSCCM internal Local CAN fault
Local CAN network fault
U2003 AUDIO In Car Entertainment CD autochanger not responding on D2B network N FC108 D2B “wake-up” circuit: open circuit, short circuit
-1 CD autochanger D2B “wake-up” fault
-2
CD autochanger D2B fault
FC94
-9 D2B network fault
-10
U2008 AUDIO In Car Entertainment CPCM not responding on D2B network N FC108 D2B “wake-up” circuit: open circuit, short circuit
-1 CPCM D2B “wake-up” fault
-2
CPCM D2B fault
FC94
-9 D2B network fault
-10
U2012 DSCCM Dynamic Stability Control CAN Communication fault N FH103 CAN circuit:
-11 open circuit, short circuit to B+ voltage, short circuit to ground
-12 DSCCM internal CAN fault
-14
-15 CAN network fault
U2019 AUDIO In Car Entertainment VACM not responding on D2B network N FC108 D2B “wake-up” circuit: open circuit, short circuit
-1 VACM D2B “wake-up” fault
-2
VACM D2B fault
FC94
-9 D2B network fault
-10
U2023 ASCCM Adaptive Speed Control CAN fault message received from other network N FH107 CAN / ASC related fault: ECM, TCM, DSCCM, IC
module(s) -4 ASCCM internal CAN fault
-10
CAN network fault
U2202 DSCCM Dynamic Stability Control CAN Invalid configuration data received N FH103 ECM, TCM or ASCCM incorrectly configured
-11
-12
-14
-15
U2501 ASCCM Adaptive Speed Control CAN ECM “token” missing N FH107 CAN ECM token missing on network (other CAN modules also flag
-4 ECM token missing fault)
-10 ECM / CAN fault
CAN network fault
U2502 ASCCM Adaptive Speed Control CAN TCM “token” missing N FH107 CAN TCM token missing on network (other CAN modules also flag
-4 TCM token missing fault)
-10 TCM / CAN fault
CAN network fault
U2503 ASCCM Adaptive Speed Control CAN IC “token” missing N FH107 CAN IC token missing on network (other CAN modules also flag IC
-4 token missing fault)
-10 IC / CAN fault
CAN network fault
U2504 ASCCM Adaptive Speed Control CAN DSCCM “token” missing N FH107 CAN DSCCM token missing on network (other CAN modules also flag
-4 DSCCM token missing fault)
-10 DSCCM / CAN fault
CAN network fault
U2515 DSCCM Dynamic Stability Control CAN Adaptive speed control message missing N — TCM CAN DTC flagged
U2515 IC Instrumentation CAN ASCCM message missing N — ASCCM CAN DTC flagged
U2516 ASCCM Adaptive Speed Control CAN TCM message missing N — TCM CAN DTC flagged
U2516 IC Instrumentation CAN not responding N FC15 Multiple CAN modules with CAN DTCs flagged
-10 CAN circuit:
-20 open circuit, short circuit to B+ voltage, short circuit to ground
IC internal CAN fault
CAN network fault
U2518 IC Instrumentation CAN A/CCM message missing N — A/CCM CAN DTC flagged
U2520 ASCCM Adaptive Speed Control CAN IC module missing N FH107 Instrument cluster CAN circuit:
-4 open circuit, short circuit to B+ voltage, short circuit to ground
-10 Instrument cluster CAN fault
CAN network fault
U2521 ASCCM Adaptive Speed Control CAN DSCCM module missing N FH107 DSCCM CAN circuit:
-4 open circuit, short circuit to B+ voltage, short circuit to ground
-10 DSCCM CAN fault
CAN network fault
U2521 IC Instrumentation CAN DSCCM message missing N — DSCCM CAN DTC flagged
U2522 ASCCM Adaptive Speed Control CAN TCM module missing N FH107 TCM CAN circuit:
-4 open circuit, short circuit to B+ voltage, short circuit to ground
-10 TCM CAN fault
CAN network fault
U2522 DSCCM Dynamic Stability Control CAN TCM module missing N FH103 TCM CAN circuit:
-11 open circuit, short circuit to B+ voltage, short circuit to ground
-12 TCM CAN fault
-14
-15 CAN network fault
U2522 IC Instrumentation CAN TCM message missing N — TCM CAN DTC flagged
U2523 ASCCM Adaptive Speed Control CAN ECM module missing N FH107 ECM CAN circuit:
-4 open circuit, short circuit to B+ voltage, short circuit to ground
-10 ECM CAN fault
CAN network fault
U2523 DSCCM Dynamic Stability Control CAN ECM module missing N FH103 ECM CAN circuit:
-11 open circuit, short circuit to B+ voltage, short circuit to ground
-12 ECM CAN fault
-14
-15 CAN network fault
U2523 IC Instrumentation CAN ECM message missing N — ECM CAN DTC flagged
U2527 DSCCM Dynamic Stability Control Local CAN network (steering angle sensor, yaw N FH103 Local CAN circuit:
rate and lateral acceleration sensor) transmit fault -25 open circuit, short circuit to B+ voltage, short circuit to ground
-29 DSCCM internal Local CAN fault
Local CAN network fault
U2601 AMP In Car Entertainment D2B “wake-up” circuit fault N CA263 D2B “wake-up” circuit: short circuit to ground
-5
U2601 AUDIO In Car Entertainment D2B “wake-up” circuit fault N FC94 D2B “wake-up” circuit: short circuit to ground
-19
U2601 CPCM Telephone D2B “wake-up” circuit fault N CA261 D2B “wake-up” circuit: short circuit to ground
-23
U2601 VACM Voice Control D2B “wake-up” circuit fault N CA300 D2B “wake-up” circuit: short circuit to ground
-14
U2602 AUDIO In Car Entertainment D2B network “ring” incomplete (fault reported) N FC108 D2B network module disconnected
-1 D2B network circuit: open circuit
-2
U2603 AUDIO In Car Entertainment D2B network “ring” incomplete (fault not reported) N FC108 D2B network module disconnected
-1 D2B network circuit: open circuit
-2
U2604 AUDIO In Car Entertainment D2B network “ring” incomplete (corrupted fault N FC108 D2B network module disconnected
report) -1 D2B network circuit: open circuit
-2
U2605 AUDIO In Car Entertainment Audio unit unable to initialize it’s address N FC108 More than one master module (audio unit) on the D2B network ring
-1
-2
U2606 AUDIO In Car Entertainment D2B slave module unable to initialize it’s address N FC108 One or more slave modules duplicated on the D2B network ring
-1
-2
U2607 AUDIO In Car Entertainment D2B slave module switched into bypass mode N FC108 One or more slave modules on the D2B network ring switched into
-1 bypass mode
-2
U2609 AMP In Car Entertainment D2B “wake-up” signal out of specification N CA263 D2B “wake-up” circuit: high resistance
-5 D2B network slave module failure
Power amplifier failure
U2609 AUDIO In Car Entertainment D2B “wake-up” signal out of specification N FC94 D2B “wake-up” circuit: high resistance
-19 D2B network slave module failure
Power amplifier failure
U2609 CPCM Telephone D2B “wake-up” signal out of specification N CA261 D2B “wake-up” circuit: high resistance
-23 D2B network slave module failure
Power amplifier failure
U2609 VACM Voice Control D2B “wake-up” signal out of specification N CA300 D2B “wake-up” circuit: high resistance
-14 D2B network slave module failure
Power amplifier failure
U2610 AMP In Car Entertainment D2B network “position status report” not received N — D2B network error
U2610 CPCM Telephone D2B network “position status report” not received N — D2B network error
U2610 VACM Voice Control D2B network “position status report” not received N — D2B network error
U2611 AMP In Car Entertainment D2B network “alarm clear command” not received N — D2B network error
U2611 CPCM Telephone D2B network “alarm clear command” not received N — D2B network error
U2611 VACM Voice Control D2B network “alarm clear command” not received N — D2B network error
U2613 AUDIO In Car Entertainment NCM not responding on D2B network N FC108 D2B “wake-up” circuit: open circuit, short circuit
-1 NCM D2B “wake-up” fault
-2
NCM D2B fault
FC94
-9 D2B network fault
-10
U2614 AUDIO In Car Entertainment Power amplifier not responding on D2B network N FC108 D2B “wake-up” circuit: open circuit, short circuit
-1 Power amplifier D2B “wake-up” fault
-2
Power amplifier D2B fault
FC94
-9 D2B network fault
-10