Professional Documents
Culture Documents
Blue Book Terms Part 1 Powerpoint 2
Blue Book Terms Part 1 Powerpoint 2
1-100
Is the most common dryer used which consist
of rotating cylinder inside which the materials
flow while getting in contact with hot gas.
a. Tower dryer
b. Centrifugal dryer
c. Trey dryer
d. Rotary dryer
Is the ratio of the mass of water-vapor in air
and the mass of air if it is saturated is called:
a. Humidity ratio
b. Mass ratio
c. Vapor ratio
d. Relative humidity
The hands feel painfully cold when the skin
temperature reaches
a. 8 deg C
b. 10 deg C
c. 12 deg C
d. 14 deg C
The refrigerant used in steam jet cooling is:
a. Steam
b. R-11
c. Ammonia
d. Water
The total heat of the air is a function of
a. WB temperature
b. DP temperature
c. DB temperature
d. WB depression
Boiling point of Freon-12 at atmospheric
pressure is:
a. 21 deg F
b. 15 deg F
c. 5 deg F
d. 28 deg F
Which of the following is NOT a type of water
cooled condenser in refrigeration?
a. Double pipe
b. Double shell
c. Shell and coil
d. Shell and tube
Component of absorption refrigeration
system in which the solution is cooled by
cooling water.
a. Rectifier
b. Generator
c. Evaporator
d. Absorber
Cascade refrigeration cycle is often used in
industrial process where objects must be
cooled to temperature below:
a. -46 deg C
b. -56 deg C
c. -66 deg C
d. -76 deg C
Type of refrigerant control designed to
maintain a pressure difference while the
compressor is operating.
a. Thermostatic expansion valve
b. Using low side float flooded system
c. Automatic expansion valve
d. Capillary tube
As a rule of thumb, for a specified amount of
compressed air, the power consumption of
the compressor decreases by
______________ for each 3 deg C drop in the
temperature inlet air to the compressor.
a. 1 percent
b. 1.5 percent
c. 2 percent
d. 2.5 percent
Modern way of detecting air compressor leak
is by using
a. Soup and water
b. Air leak detector
c. Acoustic leak detector
d. Ammonia leak detector
For foundation of stacks, the maximum
pressure on the soil is equal to the pressure
due to the weight and the ___________.
a. Soil movement
b. Wind movement
c. Ground movement
d. Engine movement
Foundation bolts of specified size should be
used and surrounded by a pipe sleeve with an
inside diameter of at least
a. 3 times the diameter of engine bolt
b. 2 times the diameter of engine bolt
c. 3 times the diameter of anchor bolt
d. 2 times the diameter of anchor bolt
For multi stage compression of an ideal
Brayton cycle, the back ratio will
a. Increase
b. Decrease
c. Remains the same
d. None of these
Type of turbine that has a specific speed
below 5.
a. Impulse turbine
b. Propeller turbine
c. Francis turbine
d. Deriaz turbine
A high discharge type of turbine
a. Impulse turbine
b. Propeller turbine
c. Francis turbine
d. Deriaz turbine
Use to minimize the speed rise due to a
sudden load rejection
a. Needle valve
b. Wicket gate shut-off
c. Shut-off valve
d. Jet deflector
Is the speed of a turbine when the head on
the turbine is one meter
a. Specific speed
b. Rated speed
c. Utilized speed
d. Unit speed
Is a fluid property which refers to the
intermolecular attraction by which the
separate particles of the fluid arc held
together.
a. Cohesion
b. Adhesion
c. Surface tension
d. Hypertension
Which of the following is NOT the cause of
black smoke in diesel engine?
a. Fuel valve open too long
b. High compression pressure
c. Carbon in exhaust pipe
d. Overload on engine
Which of the following is not a method of
starting a diesel engine?
a. Manual: rope, crank and kick
b. Electric (battery)
c. Compressed air
d. Using another generator
Two-stroke engine performs ________ to
complete one cycle.
a. Suction and discharge stroke
b. Compression and power stroke
c. Power and exhaust stroke
d. Suction and exhaust stroke
A type of geothermal plant used when there
is a presence of brine extracted from
underground
a. Dry geothermal plant
b. Double-flash geothermal
c. Single flash geothermal plant
d. Binary geothermal plant
Is the most important safety device on the
power boiler.
a. Check valve
b. Gate valve
c. Safety valve
d. Globe valve
During hydrostatic test, the safety valves
should be
a. Removed
b. Open
c. Closed
d. Partially closed
Where deaerating heaters are not employed,
it is recommended that the temperature of
the feed water be not less than ______
a. 197 deg C
b. 102 deg C
c. 104 deg C
d. 106 deg C
Is a reaction during which chemical energy is
released in the form of heat.
a. Cosmic reaction
b. Ethnic reaction
c. Endothermic reaction
d. Exothermic reaction
By reheating the steam in an ideal Ranking
cycle the heat rejected will.
a. Increase
b. Decrease
c. Remains the same
d. None of these
By increasing the boiler pressure in Rankine
cycle the moisture content at boiler exit will.
a. Increase
b. Decrease
c. Remains the same
d. None of those
Presently the highest steam temperature
allowed at the turbine inlet is about ______.
a. 340 deg C
b. 520 deg C
c. 620 deg C
d. 1020 deg C
Two most common gases employed in
Stirling and Ericsson cycles are.
a. Air and helium
b. Oxygen and helium
c. Hydrogen and helium
d. Nitrogen and helium
In most common design of gas turbine, the
pressure ratio ranges from
a. 10 to 12
b. 11 to 16
c. 12 to 18
d. 15 to 20
In brayton cycle, the heat is transformed
during what process?
a. Constant temperature
b. Isentropic process
c. Isobaric process
d. Isochoric process
The fuel injection process in diesel engine
starts when the piston ______
a. Is at the TDC
b. Leaving TDC
c. Approaches TDC
d. Halfway of the stroke
If the cut-off ratio of diesel cycle increases,
the cycle efficiency will
a. Decrease
b. Increase
c. Remains the same
d. None of these
The fuel used in a power plant that is used
during peak periods.
a. Gas
b. Solid
c. Liquid
d. None of these
Typical compression ratio of Otto cycle is
a. 6
b. 8
c. 10
d. 12
If joule Thomson coefficient is equal to zero,
then the process will become
a. Isentropic
b. Isenthalpic
c. Isobaric
d. Isothermal
If the fluid passed through a nozzle its
entropy will:
a. Increase
b. Decrease
c. Remains the same
d. None of these
Refrigerant consisting of mixtures of two or
more different chemical compounds, often
used individuals as refrigerant for other
applications.
a. Suspension
b. Compound reaction
c. Blends
d. Mixing of refrigerant
Pairs of mating stop valves that allow
sections of a system to be joined before
opening these valves or separated after
closing them
a. Check valve
b. Gate valve
c. Safety valve
d. Companion valve
An enclosed passage way that limits travel to
a single path.
a. Corridor
b. Hallway
c. Lobby
d. Tunnel
For immediate dangerous to life or health
(IDHL), the maximum concentration from
which unprotected persons are able to escape
within _____ without escape-impairing
symptoms or irreversible health.
a. 15 min
b. 1 min
c. 20 min
d. 30 min
The volume as determined from internal
dimensions of the container with no
allowance for the volume of internal parts.
a. Internal allowance
b. Internal gross volume
c. Internal interference volume
d. Internal fits volume
A waiting room or large hallway serving as a
waiting room
a. Terrace
b. Rest room
c. Compound room
d. Lobby
A continuous and unobstructed path of travel
from any point in a building or structure to a
public way
a. Average of aggress
b. Mean of aggress
c. Hallway of aggress
d. Pathway of aggress
Any device or portion of the equipment used
to increase refrigerant pressure
a. Pressure relief device
b. Pressure-imposing element
c. Pressure lift device
d. Pressure limiting device
The quantity of refrigerant stored at some
point is the refrigeration system for
operational, service, or standby purposes/
a. Pressure vessel
b. Pumpdown charge
c. Liquid receiver
d. Accumulator
Secondary refrigerant is a liquid used for the
transmission of heat, without a change of
state, and having no flash point or a flash
point above ______ as determined from
ASTM
a. 150 F
b. 160 F
c. 180 F
d. 200 F
A service valve for dual pressure-relief devices
that allows using one device while isolating
the other from the system, maintaining one
valve in operation at all times.
a. Three-way valve
b. Two-way valve
c. One-way valve
d. Four-way valve
Tubing that is unenclosed and therefore
exposed to crushing, abrasion, puncture, or
similar damage after installation.
a. Protected tubing
b. Bare tubing
c. Open tubing
d. Unprotected tubing
Refers to blends comprising multiple
components of different volatile that, when used
in refrigeration cycles, change volumetric
composition and saturation temperature as they
evaporate (boil) or condense at constant
pressure.
a. Zeolite
b. Blending
c. Composition
d. Zeotropic
Is a premises or that of a premise from which,
because they are disabled, debilitated, or
confined, occupants cannot readily leave
without the assistance of others
a. Institutional occupancy
b. Public assembly occupance
c. Residential occupancy
d. Commercial occupancy
Is one in which a secondary coolant is in direct
contact with the air or other substance to be
cooled or heated.
a. Double indirect open spray system
b. Indirect open spray system
c. Indirect closed system
d. Indirected, verted closed system
Refrigerant number R-744 is
a. Butane
b. Carbon monoxide
c. Propane
d. Carbon dioxide
Refrigerant number R-1150 is
a. Propylene
b. Ethene
c. Ethane
d. Methyl formate
Refrigerant R-40 is
a. Chlorodifluoromethane
b. Difluoromenthane
c. Ammonia
d. Chloromethane
When the air duct system serves several enclosed
spaces, the permissible quantity of refrigerant in
the system shall not exceed the amount
determined by using the total volume of those
spaces in which the airflow cannot be reduced to
less than ____ of its maximum when the fan is
operating
a. One-quarter
b. One half-quarter
c. Three-quarter
d. One-fourth-quarter
The space above a suspended ceiling shall not
be included in calculating the permissible
quantity of refrigerant in the system unless
such space is continuous and is part of the air
return system
a. Partition
b. Plenums
c. Separator
d. Plate divider
Which of the following is not a possible
location of service valve?
a. Suction of compressor
b. Discharge of compressor
c. Outlet of liquid receiver
d. Outlet of condenser
A coil in series with evaporator that is use to
prevent the liquid refrigerant entering the
compressor
a. Accumulator
b. Liquid superheater
c. Drier loop
d. Liquid suction heat exchanger
A type of valve connected from discharge of
compressor directly to suction that is
normally closed and will open automatically
only if there is high discharge pressure
a. Check valve
b. Solenoid valve
c. King valve
d. Relief valve
Use to increase the capacity of condenser
a. Water regulating valve
b. Desuperheating coils
c. Liquid-suction heat exchanger
d. Condenser heating coils
Is use to subcooled the refrigerant from the
condenser
a. Liquid subcooler
b. Condenser subcooler
c. Desuperheating coils
d. Liquid receiver
Which of the following is NOT a part of low
pressure side in refrigeration system?
a. Compressor
b. Condenser
c. Liquid line
d. Suction line
Which of the following is NOT a part of high
pressure side in refrigeration system?
a. Compressor
b. Condenser
c. Liquid line
d. Suction line
Which of the following is NOT a part of
condensing unit?
a. Compressor
b. Discharge line
c. Condenser
d. Liquid line
By subcooling the refrigerant in refrigeration
system, the compressor power per unit mass
will
a. Increase
b. Decrease
c. Remains the same
d. None of these
Superheating the refrigerant in refrigeration
system without useful cooling, the
refrigeration effect per unit mass will
a. Increase
b. Decrease
c. Remains the same
d. None of these
By subcooling the refrigerant in refrigeration
system, the specific volume at compressor
suction will
a. Increase
b. Decrease
c. Remains the same
d. None of these
Pressure loss due to friction at the condenser,
the compressor power per unit mass will
a. Increase
b. Decrease
c. Remains the same
d. None of these
Which of the following is NOT a type of
air-cooled condenser?
a. Shell and tube
b. Natural draft
c. Forced draft
d. Induced draft
A type of refrigerant control typically used in
household refrigeration
a. Thermostatic expansion valve
b. Automatic expansion valve
c. Capillary tube
d. High side float
Type of condenser that operates like a cooling
water
a. Air-cooled condenser
b. Evaporative condenser
c. Shell and tube condenser
d. Water cooled condenser
The major problem of heat pump is
a. Refrigerant used
b. Outside air
c. Supply air
d. Frosting
Dominant refrigerant used in commercial
refrigeration system
a. R11
b. R22
c. R12
d. R502
Cascade refrigerant system are connected in
a. Series
b. Parallel
c. Series-parallel
d. Parallel
Is use to heat up the solution partially before
entering the generator in absorption
refrigeration system
a. Rectifier
b. Absorber
c. Regenerator
d. Pump
The COP of actual absorption refrigeration
system is usually
a. Less than 1
b. Less than 2
c. Less than 3
d. Less than 4
Sight glass is often located at
a. Discharge line
b. Liquid line
c. Between condenser and liquid receiver
d. Suction line
Use to detects a vibration in current caused
by the ionization of decomposed refrigerant
between two opposite charged platinum
electrodes
a. Electronic detector
b. Halide torch
c. Bubble method
d. Pressurizing
The ability of oil to mix with refrigerants
a. Carbonization
b. Purging
c. Mixing
d. Miscibility
Joints and all refrigerants-containing parts of a
refrigerating system located in an air duct
carrying conditioned air to and from an occupied
space shall be constructed to withstand a
temperature of ____ without leakage into the
airstream.
a. 550F
b. 600F
c. 650F
d. 700F
Refrigerant piping crossing an open space that
affords passageway in any building shall be not
loss than ______ above the floor unless the
piping is located against the ceiling of such space
and is permitted by the authority having
jurisdiction
a. 2.2 m
b. 3.2 m
c. 4.2 m
d. 5.2 m
Methyl chloride shall not be in contact with
a. Aluminum
b. Zinc
c. Magnesium
d. All of these
Shall not be in contact with any halogenated
refrigerants
a. Aluminum
b. Zinc
c. Magnesium
d. All of these
Are suitable for use in ammonia system
a. Copper
b. Aluminum and its alloy
c. Plastic
d. Cast iron
In a pressure-relief device is used to protect a
pressure vessel having an inside dimension of 6 in
or less, the ultimate strength of the pressure
vessel so protected shall be sufficient to
withstand a pressure at least ____ the design
pressure
a. 2 times
b. 3 times
c. 4 times
d. 5 times
Seats and discs shall be limited in distortion,
by pressure or other cause, to set pressure
change of not more than ____ in a span of
five years.
a. 1%
b. 5%
c. 10%
d. 50%
Liquid receivers, if used or parts of a system
designed to receive the refrigerant change
during pumpdown charge. The liquid shall not
occupy more than ____ of the volume when
temperature of the refrigerant is 90F
a. 80%
b. 85%
c. 90%
d. 95%
The discharge line (B4) shall be vented to the
atmosphere through a ____ fitted to its upper
extremity.
a. Nozzle
b. Convergent-divergent nozzle
c. Pipe
d. Diffuser
Convert fossil fuels into the shaft work
a. Nuclear power plant
b. Gas turbine power plant
c. Dendrothermal power plant
d. Thermal power plant
Ultimate strength drops by 30% as steam
temperature raises from ____ for unalloyed
steel
a. 300 to 400 c
b. 400 to 500 c
c. 600 to 700 c
d. 700 to 800 c
Recent practice limits steam temperature to
a. 438 c
b. 538 c
c. 648 c
d. 738 c
In a closed feed water heater, the feed water
pass through
a. Inside the tube
b. Outside the tube
c. Inside the shell
d. Outside the shell
Is use if extracted steam upon condensation
gets subcooled
a. Trap
b. Deaerator
c. Filter
d. Drain cooler
Needs only single pump regardless of number
of heaters
a. Open heater
b. Closed heater
c. Mono heater
d. Regenerative heater
Is also known as deaerator
a. Open heater
b. Closed heater
c. Reheat heater
d. Regenerative heater
Dissolve gases like _____ makes water
corrosive react with metal to form iron oxide
a. O2 and N2
b. O2 and CO
c. O2 and CO2
d. N2 and SO2