Brivo OEC 850 Mobile - Rev8 (2011) Service Manual
Brivo OEC 850 Mobile - Rev8 (2011) Service Manual
5358881-1EN
Rev. 8
© 2011
General Electric Company
All Rights Reserved
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Revision History
Revision Date (Month & Year) Description of Change
1 Feb. 2010 Initial release
2 Apr. 2010 Update information
3 May.2010 Update information
4 June.2010 Update information
5 July. 2010 Update information
6 Nov. 2010 Update information
7 Jan. 2011 Update information
8 Aug. 2011 Update information
IMPORTANT SAVE THESE INSTRUCTIONS. . PLEASE READ THIS MANUAL BEFORE USING Brivo OEC 850 Mobile C-Arm
X-ray Product.
This manual may not be reproduced, in whole or in part, without the written permission of GE Healthcare.
Other product and company names mentioned herein are the property of their respective owners.
The contents of this document are accurate at the time of publication. However, changes in design and
additional features can, at any time, be incorporated in the hardware and software and may not be reflected in
this version of the document. Contact GE Healthcare Technical Support for clarification, if discrepancies arise.
The text of this manual was originally written, approved and published by the manufacturer in English.
GE HUALUN Medical Systems Co. Ltd., a General Electric company, going to market as GE Healthcare.
GE HUALUN Medical Systems Co. Ltd
No. 1 Yongchang North Road
Beijing Economic & Technological Development Area
Beijing, P.R. China 100176
Tel: 8610-58068888
Fax: 8610-67881850
i
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
REGULATORY REQUIREMENTS
This product complies with the regulatory requirements of the following:
Council Directive 93/42/EEC concerning medical devices: the CE 0459
CE label affixed to the product testifies compliance to all requirements of the Directive.
The location of the CE 0459 label is described in this manual.
European Representative:
GE Medical Systems S.C.S.
Quality Assurance Manager
283 rue de la Minière
78530 BUC France
Tel: +33 1 30 70 40 40
International Electrotechnical Commission (IEC), international standards organization, when applicable.
ii
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
iii
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
iv
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
v
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
vi
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
vii
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Contents
Chapter1. Introduction and Safety .......................................................................................................................................1-1
1.1. Introduction .............................................................................................................................................................. 1-2
1.1.1. Objective ......................................................................................................................................................... 1-2
1.1.2. Scope ................................................................................................................................................................ 1-2
1.1.3. Service Philosophy ..................................................................................................................................... 1-2
1.1.4. Qualifications ................................................................................................................................................ 1-2
1.1.5. Unauthorized Modifications .................................................................................................................. 1-2
1.1.6. Manual Organization and Use ............................................................................................................. 1-2
1.2. Safety ........................................................................................................................................................................... 1-3
1.2.1. Safety Hazard Alerts ................................................................................................................................. 1-3
1.2.2. Ingress of Fluids .......................................................................................................................................... 1-4
1.2.3. Electrical Shock............................................................................................................................................ 1-4
1.2.4. Explosion ......................................................................................................................................................... 1-5
1.2.5. Thermal Harm .............................................................................................................................................. 1-5
1.2.6. Equipment Stability .................................................................................................................................... 1-5
1.2.7. X-Radiation .................................................................................................................................................... 1-6
1.2.8. Motorized Mechanical Movement ...................................................................................................... 1-6
1.2.9. Safety Interlock ............................................................................................................................................ 1-7
1.2.10. Labels ............................................................................................................................................................... 1-7
1.2.11. Locations of the Labels .......................................................................................................................... 1-16
1.2.12. Symbols ......................................................................................................................................................... 1-18
1.2.13. Electromagnetic Compatibility Statement ................................................................................... 1-19
1.2.14. Lock-Out, Tag-Out .................................................................................................................................... 1-25
Chapter2. System Overview ....................................................................................................................................................2-1
2.1. System Descriptions ............................................................................................................................................. 2-2
2.1.1. System overview ......................................................................................................................................... 2-2
2.1.2. Component Locator .................................................................................................................................. 2-3
2.2. System block ............................................................................................................................................................ 2-5
2.3. System Schematics .............................................................................................................................................. 2-6
Chapter3. Installation .................................................................................................................................................................3-1
3.1. Overview .................................................................................................................................................................... 3-2
3.2. Pre-Installation........................................................................................................................................................ 3-2
3.2.1. Dimensions and Weights of System.................................................................................................. 3-2
viii
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
ix
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
x
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
xi
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
xii
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
xiii
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
xiv
Chapter1. Introduction and Safety
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1.1. Introduction
1.1.1. Objective
Provide Brivo OEC 850 Mobile C-Arm X-ray Product service documentation that is consistently organized,
easy to access and is designed to aggressively expedite fault isolation and decrease product down-time.
1.1.2. Scope
This manual’s contents document the necessary information for service.
1.1.4. Qualifications
Reading this manual does not qualify an untrained person to service the equipment. This publication
assumes the reader is a skilled and fully qualified electronic technician who has experience servicing
medical imaging systems. Factory trained service personnel will benefit the most from this material.
1-2
Introduction and Safety
Subsystem-The subsystems have been analyzed and divided into functional sections. Each
functional section contains major assembly and control locations, theory, functional tests and
other information relevant at the subsystem level.
Adjustment and Calibration-Procedures for tuning and calibration relevant at the subsystem
and system level.
Software Maintenance- Provides procedures for software maintenance and service mode
utilities.
Troubleshooting- Provides error code, error messages, and diagnostic programs that expedite
the diagnostic process.
Replacement- Removal and installation procedures for fuses, covers and field replaceable units.
Periodic Maintenance Procedure-Procedures for periodic maintenance.
Technique Reference-Technique Reference of the system.
Appendix-Schematics and information of some key parts.
1.2. Safety
Do not attempt to service or maintain this equipment before reading this entire section.
WARNING indicates a potentially hazardous situation that, if not avoided, could result in
WARNING
death or serious injury.
CAUTION CAUTION indicates a potentially hazardous situation that, if not avoided, may result in
moderate to minor injury, equipment damage or loss of data.
1-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
The equipment is not rated for water-tight operation. Do not allow any liquids to leak into
WARNING the equipment where they can cause electric shock, fires, and short circuits. If leakage
does occur, ensure that all internal circuitry is completely dry before attempting to
operate the equipment.
Never store or operate the system in the presence of conductive fluids like water or
WARNING saline solution unless the system is adequately protected by an approved bagging or
draping system.
Equipment that contains high power electrical components must be serviced only by
WARNING personnel familiar with proper safety procedures for working near these components.
Disconnect AC power (and battery packs if used) before discharging static electricity in
WARNING components such as electrolytic capacitors and high voltage cables. Failure to heed this
message will result in death or severe personal injury.
Allow adequate time for static charges to discharge through bleeder resistors. Use a
WARNING high wattage resistor when discharging circuits to avoid burns.
Have someone watch while you work near high voltages. This person must remain
WARNING clear of all circuitry and be prepared to turn off the power to the system and render aid
in an emergency.
High voltage cables, electrolytic capacitors, and CRTs can retain a dangerous static
charge for long periods after power has been removed. Some devices can acquire a
WARNING charge spontaneously without direct contact with other circuitry. Do not touch these
components unless power has been completely removed and they have been
discharged.
Never operate the system unless all safety ground wires (green wire with a yellow stripe)
CAUTION
and related components are fastened in place. Dangerous electrical shock and
improper equipment operation can otherwise result.
Remove all metal rings and watchbands before working on system circuitry. Skin burns
CAUTION and damage from involuntary muscle contractions can result if metal jewelry shorts
electrical circuits.
1-4
Introduction and Safety
1.2.4. Explosion
If an abnormal condition occurs, such as the room fills with flammable gas, steps must be taken to
prevent the gas from contacting components within the equipment. Follow these guidelines:
1. Do not turn the system on or off.
2. Do not un-plug or plug-in system or peripheral equipment power cords.
3. Do not operate light switches or other electrical equipment.
4. Evacuate all personnel immediately.
5. Notify the hospital administration and/or fire department.
6. Ventilate the room to clear the air of all flammable vapor or gas.
7. Identify and remove the source of the flammable liquid, vapor, or gas.
1-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1.2.7. X-Radiation
This equipment either produces or is used in the vicinity of ionizing radiation. Observe
CAUTION proper safety practices during operation. Use lead aprons, eye protection, thyroid
protection, and similar devices to protect yourself and others.
CAUTION Where local Entrance Exposure Rates (EER) are different than the GE HUALUN rate
specified, the EER should be adjusted to the lower of the two.
1-6
Introduction and Safety
WARNING Never bypass, jumper, or otherwise disable any equipment safety feature.
1.2.10. Labels
Even though this manual is supplied only in English, some labels may have a foreign
NOTE language equivalent that will appear on your system.
1-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
9 1
1-8
Introduction and Safety
1-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
15
IPX8 1
protection of the footswitch is IP
X8. The electrical mechanism
within the footswitch is protected
from the effects of continuous
immersion in water.
1-10
Introduction and Safety
1-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1-12
Introduction and Safety
1-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1-14
Introduction and Safety
42 1 Image Intensifier
43 1 PLC label
1-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
12
1-16
Introduction and Safety
41
14
30
1-17
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1.2.12. Symbols
Be familiar with the following symbols that may appear on equipment and schematics so you can safely
maintain and operate the system:
Dangerous Voltage
This symbol identifies areas where hazardous voltages may be present. Use appropriate
safety precautions.
This symbol identifies the system’s main protective earth ground terminal, which connects to
the facility earth ground through the grounding prong on the AC power plug. This connection
must be in place at all times for safe system operation.
This symbol identifies an earth ground connection that is necessary to maintain grounding
throughout the system.
X-Ray Source
This X-Ray Source symbol is used to identify controls that will produce ionizing X-radiation
when activated. Always use appropriate safety precautions when generating X-rays.
This X-Ray Source symbol is used to identify controls that will produce ionizing X-radiation
when activated. Always use appropriate safety precautions when generating X-rays.
This symbol identifies system terminals which, when connected together, are at the same
potential (not necessarily earth ground). Green/yellow wires normally connect potential
equalization terminals together.
Attention
Attention, see accompanying documentation for information. You can refer to this manual for
the operation instructions.
1-18
Introduction and Safety
Type B
This symbol indicates the equipment is protected against electric shock by a protective earth
ground connection.
Ionization Radiation
This symbol indicates that there is ionization radiation.
This equipment generates, uses, and can radiate radio frequency energy. The
NOTE equipment may cause or be subject to radio frequency interference with other medical
and non–medical devices and radio communications. To provide reasonable
protection against such interference, the Brivo OEC 850 system complies with
emissions limits for a Group 1, Class A Medical Devices and has applicable immunity
level as stated in IEC60601-1-2: 2001 Amd.1: 2004 Ed2.1.
1-19
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Use of accessories, transducers, cables and other parts other than those specified by
the manufacturer of this equipment may result in increased emissions or decreased
WARNING immunity of the equipment. The manufacturer is not responsible for any interference
caused either by the use of interconnect cables other than those recommended, or
unauthorized changes or modifications to this equipment. Unauthorized changes or
modifications could void the user’s authority to operate the equipment.
1. All interconnect cables to peripheral devices must be shielded and properly grounded.
The use of cables that are not properly shielded and grounded may result in the
equipment causing radio frequency interference in violation of the European Union
Medical Device directive and FCC regulations.
Do not use devices that intentionally transmit RF signals (Cellular Phones, Transceivers,
or Radio Controlled Products) in the vicinity of this equipment as it may cause
WARNING performance outside the published specifications. Keep the power to these types of
devices turned off when near the equipment.
The medical staff in charge of this equipment is required to instruct technicians, patients,
and others.
1-20
Introduction and Safety
RF Emissions Class A The Brivo OEC 850 Mobile C-Arm X-ray Product is
suitable for use in all establishments other than
CISPR11
domestic and those directly connected to the public
Harmonic emissions Not low-voltage power supply network that supplies
applicable buildings used for domestic purposes.
IEC 61000-3-2
Voltage fluctuations/ Not
flicker emissions applicable
IEC 61000-3-3
1-21
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1-22
Introduction and Safety
a: Field strengths from fixed transmitters, such as base stations for cellular telephones and land mobile radios, amateur
radio, AM and FM radio broadcast, and TV broadcast cannot be estimated accurately. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be performed. If the measured field
strength exceeds the RF compliance level above, observe the Brivo OEC 850 Mobile C-Arm X-ray Product to verify normal
operation in each use location. If abnormal performance is observed, additional measures may be necessary, such as
re-orienting or relocating the [EQUIPMENT and/or SYSTEM].
b: Over the frequency range 150 kHz to 80 MHz, field strengths are less than 3 V/m.
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
Note3: These are guidelines. Actual conditions may vary.
1-23
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Separation Distance/m
Rated Power of
Transmitter/W
3,5 3,5 7
d =[ ] P d =[ ] P d =[ ] P
3 3 3
100 12 12 23
For transmitters rated at a power not listed above, the DISTANCE can be estimated using the equation
in the corresponding column, where P is the power rating of the transmitter in watts (W) according to
the transmitter manufacturer.
Note 1: NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
Note 3: These are guidelines. Actual conditions may vary.
1-24
Introduction and Safety
1-25
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10. In C-arm, verify zero volts AC at breaker between the brown and blue wires.
1-26
Introduction and Safety
1-27
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1-28
Chapter2. System Overview
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
2-2
System Overview
8
9 2
10 3
15
11 4 16
12
18
13 6 19 17
14 1
7
4
1
2 5
3 7 10 10
11
9 9
8 8
1. LCD Monitors
2. Keyboard
3. USB connector
4. Exposure indicator
5. Mouse
6. Cabinet for printer
7. DVD driver
8. Front wheels
9. Back wheels
10. Handles
11. Interface for DICOM and Video distributor
2-4
System Overview
2-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
2-6
System Overview
2-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
2-8
Chapter3. Installation
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3.1. Overview
This chapter described the installation procedure of Brivo OEC 850 Mobile C-Arm X-ray Product.
3.2. Pre-Installation
Enough room should be provided for the movement, installation and operation of the
WARNING system.
The floor should be hard enough to support the system. It should also be smooth and
WARNING
horizontal.
3-2
Installation
10A (220V/230V/240V)
20A (100V/110V/120V)
Suitable sockets are required both in Scan room and Operating room for maintenance. Power supply
should comply with requirement of the system power supply requirements. The sockets should be 3
cores with protective earth, which complies with the requirement of the applicable electrical codes. Other
equipment electrically connected with this apparatus share the same grounding connection.
You should check the local power supply first. If it is not 220 V/230 V/240 V (50 Hz), you
WARNING need change the power supply cables and change the connections of the system. Refer to
the Power Supply Adaptation section for details.
3.2.4. Environments
Operating Conditions:
Temperature: +10°C~+40°C (+50F~+104F)
Humidity: 20~80% Relative, non-condensing
Atmospheric Pressure: 700hPa~1060hPa
Transportation and Storage:
Temperature: -20°C~+55°C (-4°F~+131°F)
Humidity: 10~95% Relative, non-condensing
Atmospheric Pressure: 500hPa~1060hPa
3-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3-4
Installation
3.3. Unpacking
There are 2 packages for Brivo OEC 850 Mobile C-Arm X-ray Product. One is for C-Arm (L
NOTE W H=2000mm 900mm 1995mm. And the other is WorkStation (L W
H=1015mm 900mm 2150mm).
Before unpacking, inspect the shipping enclosure /boxes for damage and report to the
NOTE shipper if available.
The unpacking of the system should be done before moving it into the operation room, in order to check
if there’s damage or non-apparent damage occurred during transportation.
The packages should be examined minutely during installation to avoid missing parts with small
dimensions or envelopes containing screws, washers, etc. Once damage is observed, notify service of the
transportation and insurance company immediately.
If non-apparent damage due to transportation was found during unpacking or installation, take the
same action in 15 days after delivery. The transportation corporation will not pay for non-apparent
damage generally unless making an application for inspection in 15 days after delivery.
If damage is discovered, contact the related company immediately, with specifying the type of apparatus,
the serial number and the order number if possible, and describing the nature of the damage.
Please follow the steps below to unpack the Brivo OEC 850 Mobile C-Arm X-ray Product.
C-Arm:
1. Place the C-Arm and workstation packages on the flat and leave enough space around.
2. Cut off the binding tie and remove the cardboard coping and box of the C-Arm. Then remove the
wrapper on the C-Arm.
3. Lock the cross-arm, wig-wag, lateral rotation and orbital movement brakes. Get the accessory
packages, wood crowbar, stow-woods and ramp from the C-arm package. Put the wood ramp
behind of the C-arm.
NOTE
The ramp and crowbar will also be used to workstation unpacking.
3-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Wood
crowbar
Accessory
Stow-wood
4. Loosen the screws and remove the wood support of image intensifier.
Wood
support
Fastening
metal strip
3-6
Installation
7. Lift up one side of the C-arm with the wood crowbar and put the stow-wood under each rear
wheel. Then loose all the screws and remove the wood fastening assembly on rear wheels of the
C-arm.
8. Hold the handles and move the C-arm backward to draw out backwards the image intensifier
and tube.
NOTE
Take care to protect the Image intensifier and gird when move the C-arm.
9. Turn the right steering handle in a vertical position to keep the rear wheels in a straight direction.
Then carefully move the C-Arm backward along the ramp to the site you desire.
10. Loosen the bolt with a screwdriver and remove the horizontal cross-arm lock device. (The lock
device will also be used during workstation unpacking.) Loosen the horizontal movement brake
handle and push the C-Arm forward. Lock the brake handle.
3-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
11. Check parts according to packing list (refer to the packing list with the system for details).
Before moving the system, please make sure the 4 brake handles: the C-Arm orbital
WARNING rotation brake, the lateral rotation brake, the Wig-Wag brake, and the horizontal cross-
arm brake are locked. Otherwise, equipment damage or personal injury may result.
Workstation:
1. Cut off the binding tie and remove the packing of the workstation. Take out the ramp on standby.
And remove the wrapper on the workstation.
2. Loose the screws of the fastening assembly cover around the four wheels. Remove all the
screws on the wood support.
3. Put the cross arm lock device under the center of one side of the workstation and loosen the bolt
to lift up the workstation. Then remove the wood support. Lower the workstation and then
remove the lock device.
4. Use the lock device to lift up the other side of the workstation. And then remove the wood
support.
5. Put the ramp in position. Move the workstation along the ramp.
3-8
Installation
3.4. Inspection
3-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3-10
Installation
X-ray Tube
Control Panel
Handles
Cabinet
Wheels
3. Workstation Inspection
Inspect each workstation component listed under the heading workstation inspection. Select one check
box for each item in the list.
WorkStation Inspection
Physical Location No problem Loose or missing Broken or Chipped or
found parts damaged parts scratched paint
Monitor and Arm
Keyboard and
Mouse
Covers
Frame
Handles
Wheels
3-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3.5. Setup
3-12
Installation
The system can adapt power supply of AC100V, AC110V, AC120V, AC220V, AC230V and
NOTE AC240V by different connections of the transformer. Before install the system, please check
the power supply voltage range and the transformer connection according to the diagram
below.
Wire Transformer taps
Voltage 240 V 230 V 220 V 120 V 110 V 100V
Wire N (Brown) 1 1 1 1 1 1
Wire L1 (White) 4 3 3 4 3 2
Wire N1 (Yellow) 5 5 5 5 5 5
Wire L (Blue) 8 8 7 8 7 6
Jumper 10-11 10-11 10-11 9-10 9-10 9-10
11-12 11-12 11-12
3-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3.5.2. UPS
Follow these steps to setup the UPS.
1. Make sure that the rear cover and both lower side covers of workstation have been removed.
2. Plug the UPS battery connector.
Off
4. Press and hold UPS “test” button for several seconds to initiate a self-test. Release the button
once the UPS sounds beeps. The workstation will start up. Wait until a message display: “Power
failure! System will shut down immediately! Please check AC power and restart system later.”.
(The message will be displayed for only several seconds.)
5. Press “off” button to turn off the UPS.
6. Install all the covers of the workstation.
The UPS receives AC power whenever the system power switch is on. The battery recharges if
necessary. If the AC mains power fails, the UPS supplies power to workstation using its internal
battery.
The online indicator goes out and the battery indicator comes on. UPS sounds “bi-bi-bi-bi” every four
seconds.
Do not connect any other devices to the UPS receptacles.
WARNING
UPS battery should be disconnected before transportation. Battery can be left in the
UPS.
3-14
Installation
3-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3-16
Installation
3.5.3. Power on
When you place a recently unpacked system into use, allow it to stand in its new
environment long enough for any condensed moisture to evaporate. A decrease in
CAUTION
temperature or a humidity increase can cause water vapor in the air to condense,
sometimes on electric circuits. You may damage the equipment if you apply power
before this condensation dries.
1. Take out foot switch from the accessory package. Connect the Footswitch to C-arm.
2. Plug the power cord into appropriate AC receptacle. Press the power on switch on control panel.
Before power on the system, please check and make sure that the voltage of the system
is compatible with the power supply. Or you must change the power supply settings of
WARNING
the system.
Refer to Section 3.5.1 for details.
3. Verify that the workstation and C-arm complete software boot and initialization with no errors
reported on their displays.
The auto fluoroscopy mode is selected and the power on indicator lights. The field size is in its maximum.
The left monitor of workstation will display GE logo screen. The right monitor will enter into the PATIENT
INFORMATION Screen automatically.
4. Press vertical lift button and verify that vertical lift column is operational.
3-17
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
CAUTION The configuration must be complete in case the local regulation is not complied.
CAUTION Make sure cross arm is fully retracted and brake is set before moving C-arm. Equipment
damage or personal injury may otherwise result.
3-18
Installation
When you release the orbital movement brake, place your other hand on the C-arm so
CAUTION
that you have control of the C-arm’s movement.
1. Release the orbital brake.
2. Verify that C-arm orbits smoothly in its cradle without excessive play.
3. Verify that the entire orbital scale is readable and in good condition.
4. Set the brake handle to lock position and verify that C-arm locks firmly in position.
Lateral Rotation
1. Release lateral rotation brake.
2. Verify C-arm rotates smoothly in both directions.
3. Lock the brake and verify the brake locks C-arm firmly in position.
Before transporting the system, please make sure the 4 brake handles: the C-Arm
WARNING orbital rotation brake, the lateral rotation brake, the Wig-Wag brake, and the horizontal
cross-arm brake are locked. Otherwise, equipment damage or personal injury may
result.
1. Power on the system. Set the keyswitch in ON position ( ). Press and hold the up vertical
column switch. The maximum distance is about 40cm. Verify that vertical column stops when it
reaches the limit and that operation is smooth and quiet.
2. Press and hold down vertical column switch. When the movement stops, press two keys
at the same time and C-arm will be lowered to the lowest position.
Wheels
1. Push C-arm slowly and verify that the wheels contact the floor and that they roll freely.
2. Make sure there are no worn or damaged areas on the wheel tread.
3. Verify that there is no wobble or binding associated with wheels.
Brakes
1. Step on the rear wheel pedal brake. Verify that the rear wheels lock.
2. Step on wheel pedal release brake. Verify that brakes release and that both rear wheels roll and
steer freely.
3-19
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Steering
1. Verify that both rear casters respond appropriately to movement of the steering handle.
2. Verify that you can steer the rear casters 90 degrees to the left and 90 degrees to the right.
3. Verify that the casters track together when you steer them.
4. Place the mobile C-arm’s rear wheel brake in release position. Push the C-arm slowly and verify
that C-arm can turn smoothly.
C-Arm Controls
The following procedure produces X-rays. Use the appropriate personal protective
WARNING equipment to protect yourself from X-ray exposure.
kVp , mA/mAs
Press the kVp and mA/mAs keys and verify that the technique can be adjusted manually.
Pulse Fluoroscopy
Select Pulsed normal fluoro mode via the C-arm control panel. The X-Ray Exposure indicator keeps
lighting when taking an exposure.
If the pulse mode is enabled, the amount of accumulated time will be the actual exposure
NOTE
time, which depends on the time of pressing X-ray switch, length of pulses and the
number of pulses per second.
1pulse count to
1pps : 50 milliseconds / 1 pulse approximately
2pps : 50 milliseconds / 1 pulse approximately
4pps : 50 milliseconds / 1 pulse approximately
8pps : 50 milliseconds / 1 pulse approximately
Manual HLF +
Select manual HLF mode. Take exposure and verify that a HLF exposure is taken. Verify that audible tone
beeps at normal rate.
Auto HLF + +
Place an object in front of Image Intensifier. Select Auto HLF mode to take exposure. The exposure will
stop automatically after 20 seconds if you selected “Exposure Limit 20sec” in “Exposure Management”
screen of service tool.
3-20
Installation
Digital Spot
Select digital spot via control panel. Take a digital spot shot and verify that fluoro exposure automatically
terminates and image automatically saves to hard drive.
Image Orientation
Using the line pair tool as a phantom, take exposure in normal fluoro mode and verify the following
functions:
Collimator
Press each of the following collimator switches while taking exposure and verify each of the following
collimator actions.
Place something on the Image Intensifier. Press field size key repeatedly, verifying ability to select
any of the three available sizes: NORM, MAG1 and MAG2.
Recursive Factor
Press recursive factor key to select 2, 4, 8, 16 respectively to take an exposure. Verify the amount of
filtering can be increased and decreased. The noise in the image should be decreased as the Recursive
Factor is increased.
Motion Artifact Reduction
Take exposure and rotate the image by pressing image rotation key. Observe the motion artifact of the
image. Press motion artifact reduction key and verify that the indicator lights.
3-21
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Alarm Reset
Press and hold Alarm Reset key for approximately 2 seconds. Verify Fluoro time displayed on the C-
arm control panel resets to zero.
Radiographic Mode
Select Radiography mode and verify that the indicator lights.
Keyswitch
1. Place the X-ray keyswitch in STANDBY position ( ). Press Handswitch and verify that no X-rays
are generated. Press Vertical lift button and verify that vertical lift column is not operational.
2. Place X-ray keyswitch in XRAYOFF position ( ). Press handswitch and verify that no X-rays are
generated. Press vertical lift button and verify the vertical lift column is operational.
3. Place X-ray keyswitch in ON position ( ). Press handswitch, footswitch and vertical lift button
to verify X-ray and vertical lift column are enable.
3-22
Installation
Emergency Switch
Perform the following test to verify the emergency switch.
1. Press the emergency switch during raising C-arm.
Emergency
Switch
Workstation Operation
1. Press SWAP ( ) key and verify this function exchanges images between the left monitor and
the right monitor.
2. Press the SAVE ( ) key. And then press key. Verify that the left monitor image is previewed
in the Image Directory screen.
3. Verify Patient Information function activates the Patient Information screen. Enter patient
information ( ), display scheduled exams, display resume exams screen.
4. Verify Image Directory function ( ) allows you to enter Image Directory screen.
5. Verify the SETUP function ( ) allows access to the Setup screen. Press “Security” button and
select “Require Users to Login” in the screen.
3-23
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6. Verify ZOOM function ( ) displays a square region of interest (ROI) box and that you can
magnify the ROI.
7. Verify NEGATE ( ) function reverses the light and dark values on the image displayed on the
left monitor.
8. Verify the CONTRAST function ( ) displays and indicator bar and that the amount of
contrast can be increased and decreased.
9. Verify the BRIGHTNESS function ( ) displays an indicator bar and that amount of
brightness can be increased and decreased.
10. Verify that Auto Contrast/Brightness ( ) automatically selects the optimum values of
contrast and brightness.
11. Verify ENGE ENHANCE function ( ) displays an indicator bar and that amount of
enhancement level increased and decreased.
12. Press key on keyboard. Enter “Security” screen. Select “Require Users to Login” to enable the
logout function. The default password is “123456”. Click “Change Password…” if you need to
change password. Then Click “OK” button.
Press ALT key and the LOGOUT key ( ) at the same time. Verify that it can log the user out of the
workstation applications.
The logout function can only be available when you select “Require Users to Login” in
NOTE
the “Security” screen.
3-24
Installation
CD/DVD check
1. Place a blank CD or DVD in the in the CD/DVD drive and wait for the green LED on the front of the
drive to turn off.
2. Press the Image Directory key ( ) on the keyboard to open the Image Directory. Make sure the
Image Directory has some saved images. Otherwise, then save some images by taking test shots.
3. Select the “Copy To…” button on the “Image Directory” screen. The “Copy To… “ screen lists the
available print and storage devices. Select CD/DVD and click the “OK” button to confirm your
selection.
4. Click “Option…” button. Select “Include Viewer” in copy option and click “OK” button.
5. Select one or more images from the Image Directory.
6. Click “Copy” button on the Image Directory screen to copy the queued image.
7. Insert the CD/DVD to other computer. The media viewer will run automatically. Use the viewer to
confirm that the image was written to the CD/DVD successfully.
3-25
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
DICOM Check
You can choose the verification items from DICOM worklist server, storage server and
NOTE
printer server, according to the customer’s network situation and equipment.
2. Plug the network cable into the network connector on the computer.
3-26
Installation
5. Click “Network Config…”button. Input the “Station Name” and “AE Title”. The default AE Title is
“OEC850”. You can change it according to the DICOM service’s requirement. Click “Config…”button
and fill in the network information. You can obtain the information from network administrator.
Click “Add…” button and fill in the information of the DICOM worklist server. Obtain the information from
network administrator. Click “OK” button to return to DICOM worklist screen. Click “Verify” button. The
message “ The DICOM server has verified successfully.” will display if the server has connected. Click “OK”
button and then select the Exit button to close the DICOM Worklist screen.
3-27
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Click “Add…” button and fill in the information of the DICOM storage server. Obtain the information from
network administrator. Click “OK” button to return to DICOM storage server list screen. Click “Verify”
button. The message “ The DICOM server has verified successfully.” will display if the server has
connected. Click “OK” button and then select the “Exit” button to close the DICOM Storage server list
screen.
8. Click “DICOM printer…” button on setup screen.
3-28
Installation
Click “Add…” button and fill in the information of the DICOM printer server. Obtain the information
from network administrator. Click “OK” button to return to DICOM printer server list screen. Click
“Verify” button. The message “ The DICOM server has verified successfully.” will display if the server
has connected. Click “OK” button and then select the “Exit” button to close the DICOM printer server
list screen.
9. Press key to enter Patient Information screen. Select “Scheduled Exams…” button. Choose the
worklist server and click the “schedule filter” button. Setup the query filter and click OK.
Click “Update schedule” button to perform a DICOM query. Verify that the search results will be
displayed in the scheduled exams screen.
10. Press Image Directory key on the workstation keyboard. Select DICOM printer server from the
Copy To screen. Click the preview image and then click the queue box. Click “Print” button. Verify that
the images can be printed successfully after the process complete.
11. Click “Copy To…” button. Select the DICOM storage server. Select one or more preview images you
want to archive. Press and hold CTRL key on the keyboard to select multiple images from the
previews in the directory. Click “Copy” button. Verify that the images are copied to the storage server
successfully after the copy progress complete.
3-29
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
DICOM Worksheet
Record Network Config information below:
3-30
Installation
AE Title:
IP Address:
Gateway:
Port Number:
3-31
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
AE Title:
IP Address:
Gateway:
Port Number:
Modality
3-32
Installation
Port Number:
Maximum:
Minimum:
Config. Info.:
Border Density: BLACK WHITE
Empty Density: BLACK WHITE
Copies: 1 2 3 4 5 6 7 8 9 10
Print Priority: HIGH MEDIUM LOW
Destination: MAGAZINE PROCESSOR
Medium Type: PAPER CLEAR FILM BLUE FILM
Orientation: PORTRAIT LANDSCAPE
3-33
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Enter information above in the “Schedule Filter” screen. The users will enter additional information on this screen.
3-34
Installation
Select Auto Fluoroscopy mode ( ), and the NORM field size to take an exposure. Put the copper filter
on the tube head. Verify that the kVp changes accurately as copper filters are inserted into the field in the
following ranges:
Copper mm 1mm 2mm 3mm
kVp range 64±4kVp 74±4kVp 82±4kVp
If the kVp is not in the range, refer to 5.7.1 for calibration.
of the image and the resolution tool must be 45°. Select Manual Fluoroscopy mode ( ) and
appropriate kV value. Take an exposure, and stop when image is stable. The image is frozen on the left
monitor. Verify the resolution in lp/mm is equal to, or greater than, the values listed below. Repeat and
select any of three field sizes (NORM, MAG1 and MAG2) to verify the resolution.
Field Size NORM MAG1 MAG2
3-35
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
NOTE
After the installation, please fill in the product locator card for PLC parts below and mail
the cards to local service operation office.
German regulatory required that the collimator has to be visible on two sides of the
NOTE image, which are not opposite. For the system installed in German, adjust collimator
iris (refer to chapter5.6.4) until the collimator meet the requirement as below.
3-36
Installation
Power
cable
Set screw
3-37
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
5. Adjust the adjusters of the laser until the intersection of the laser beam is in the center circle of
the beam alignment tool. (Use the circle to adjust the line to be vertical with the other and the
screws to adjust the position of the line.)
Circle adjuster
6. Fasten the set screw a little. And the beam position will change a little. Then adjust the beam
again according to step5. Fasten the set screw to fix the beam position and direction. Then install
the laser aimer cover.
7. Functional check: Turn on the laser aimer power switch and verify that the intersection of the
laser beam is in the center circle of the beam alignment tool and the two laser lines are vertical.
3-38
Installation
Do not grasp the Laser Aimer's handle to position the C-arm or to move the system.
CAUTION Pulling the handle may cause the Laser Aimer to release from the image intensifier and
fall.
5. Use the image intensifier handle to position the C-arm or to move the system to the desired location.
6. After attaching the laser aimer, place the C-arm in the position it will be used during the procedure.
7. Turn the laser aimer ON and adjust the beam alignment knobs until the laser beam is centered on
the intersection of the cross-hair on the tube cover.
CAUTION If the laser is ON, do not look directly into the laser aimer’s aperture.
8. Functional check: Using fluoroscopy, verify that the cross-hair in the fluoro image, at the center of the
area of interest.
3-39
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
The location where the laser beam marks the patient corresponds to the center of the
NOTE area of interest, indicated by the cross-hair in the fluoro image.
Perform procedure below to remove the laser cover from the laser aimer:
1. Switch OFF the power to the laser aimer.
2. Grasp the two knobs on the laser cover.
3. Press down and rotate the cover (approximately 10 degrees counterclockwise) until the knobs align
with the notches on the housing.
4. Lift off the cover and resume laser aimer operation.
3. Plug the power supply cable to the socket on video distributor. Cut off the other end of the power
supply cable. Strip off 3 wire ends. Connect the wires to the terminal blocks at the bottom of the
workstation (connect the L line to connector 1, 2 or 3, N line to 6,7 or 8 and the ground line to
earth). Put the power supply cable along the wiring harness to get a good layout.
4. Unplug the video cable of left monitor from computer and plug it to the OUTPUT4 connector of
the video distributor.
3-40
Installation
5. Plug the video cable of video distributor to the computer’s video connector DVI-1, which was
connected with the left monitor’s cable before.
6. Functional check: Power on the system. Check that the left monitor will display GE logo screen.
Plug the left monitor video cable and connect to OUTPUT1 and OUTPUT2 respectively. Verify that
the left monitor will display GE logo screen in each case. Then connect the video cable back to
OUTPUT4 port.
3-41
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8. Only 2 DVI output connectors are available for customer to use. First loose and remove 3 screws,
and then remove the small cover.
9. Customer can connect the external monitor to OUTPUT1 or OUTPUT2 of video distributor.
OUTPUT2 OUTPUT1
10. When not use the external monitor, install the cover as before.
3-42
Installation
3.7.3. Printers
Brivo OEC 850 offers below printers as option.
UP-990AD Thermal Printer
UP-D897 Thermal Printer
Please follow below steps to install the printers.
1. Power off the system. Open the rear cover of the workstation.
2. Plug one end of the USB cable to the video port of the printer. Plug the power supply cable into the
socket on the printer. Put the cables through the hole of the workstation. Put the printer in the
cabinet.
3-43
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
4. Cut off the other end of the power supply cable. Strip off 3 wire ends.
5. Connect the wires to the terminal blocks at the bottom of the workstation (connect the L line (brown)
to connector 1 or 2 or 3, N line (blue) to 6 or 7 or 8 and the ground line (yellow and green) to earth
port. Put the power supply cable along the wiring harness to get a good layout.
Earth port
6. Functional check: Power on the system. Set the switch at back of printer to digital mode. Turn on the
printer. Verify that an image can be printed to the printer and the printer works with both paper and
film.
CAUTION The Video Printer is not fixed in the cabinet. Please pay attention when moving the
WorkStation.
3-44
Installation
The power and video signal of the View Printer is provided by EVR system. Please do not
connect the power supply and video to other printer. Please do not connect other
WARNING external power supply and video signal to this printer. Otherwise, it may cause electrical
shock to user.
Verify that the cassette holder is securely attached to the image intensifier. Unsecured
WARNING cassette holders may fall, injuring patients or personnel.
3. Insert a film cassette into the cassette holder and center it.
Verify that cassette is held securely within the cassette holder. Unsecured film cassettes
WARNING may fall, injuring patients or personnel.
4. Remove the film cassette by pushing the cassette out of the cassette holder.
5. To remove the cassette holder, open the cassette holder handle and press firmly against the side of
the cassette holder.
The cassette holder is designed to snuggle attach to the image intensifier lip when the
NOTE handle is engaged. It may be necessary to strike the cassette holder with the palm of
your hand to dislodge the cassette holder from the image intensifier.
3-45
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3.7.5. DAP
Perform the following procedure to install the DAP.
The installation and calibration procedure should be done on site even the option is ordered and shipped
with the system.
1. Loose the screws of tube cover and remove the tube cover.
2. Install the three studs on the top plate of collimator.
3. Fasten the DAP chamber to the adjustment set. Fasten the chamber set to the three studs with
screws.
4. Place the DAP module on the metal block and tighten the 2 screws as below:
DAP Module
Chamber
3-46
Installation
6. Don’t install the tube cover first. After connected all the cables. Put the circular adjustment tool
on the chamber. Ensure the circles of the iron sheet and DAP chamber are tangent.
7. Adjust precision of the DAP chamber’s position according to the procedure below:
(1) Coarse tuning
Boot up Brivo OEC 850 system. Take exposure at low kV (about 45 kV) in normal fluoro mode.
Image below will display on the screen. Release the screws that secured DAP. Adjust the
adjustable screws of the DAP chamber set until the circular image is on the center of the
screen.
Image of the
adjustment tool
(2) Fine tuning (Ensure the iris works normally before this procedure)
3-47
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Switch to the manual fluoro mode. Take exposure at high or middle kV (about 70kV).
Meanwhile, make the iris in the field and adjust kV value to ensure the edges of the iris and
circular tool are clear enough.
Adjust the screws of the chamber set until the center of the circular image and center of the
iris are superposed. Close the iris to make the image edge of the iris is close to the edge of
circular image. Maintain the center of the circular image and center of the iris are
superposed. The error of the center’s position should not exceed 2mm.
Edge of
circular tool
Edge of the
iris
8. Login the service mode. Click “Exposure management…”button on the main screen. Choose
“enable” item for the DAP option. Save the setting and shut down the system.
9. Screw down the screws that secure the DAP chamber set. Remove the circular adjustment tool.
Install the tube cover.
Dose Test and Calibration
Set Dosimeter as accumulative/maintenance. Put the detector of dosimeter on the axis of image
intensifier and focus, 30 cm away from grid center. Clear the dosimeter. Create a new exam on
workstation and ensure the DAP and dose show value on the workstation are cleared.
Set kV/mA value as 110kV/4mA in manual fluoro mode. Open the collimator completely. Take exposure
for 3-5 seconds. Record Dose show value on right monitor and dosimeter measured value. Repeat three
times and get the average of the dose show value on right monitor and the average of measured value
on dosimeter. Calculate the error between show value average and measured value average.
After each test, reset the dosimeter and create a new exam to clear the DAP and dose
NOTE
show value on workstation.
DoseMeasuredvalue Doseshowvalue
ERROR= 100%
DoseMeasuredvalue
3-48
Installation
If the error is more than 5%, adjust Dose Calibration Coefficient: Login service tool. Enter “Exposure
Management” screen. Change Dose Calibration Coefficient. Dose/Dose rate show value on the
workstation right monitor is in direct proportion with the calibration coefficient.
Dose Accuracy Test
Install the beam alignment tool on the image intensifier. Put the detector of dosimeter on the axis of
image intensifier and focus, 30 cm away from grid center. Clear the dosimeter. Take exposure at 45kV,
1.5mA and adjust the collimator opening size to settings in the table below by beam alignment tool.
Take exposure at high and lower kV/mA value at each collimator field size in the table for 3-5 seconds.
For each exposure, record the dose display values on the right monitor and measured dose values on
dosimeter before and after exposure. Calculate the difference between the values before exposure and
that after exposure.
The difference between dose value on the right monitor before exposure and the value after exposure is
the Dosevalue(on workstation). The difference between measured dose value on dosimeter before
exposure and the value after exposure is the DoseMeasuredvalue.
Calculate the error between the dose value on workstation and measured value on dosimeter.
DoseMeasuredvalue Dosevalue(onworkstation )
ERROR= 100%
DoseMeasuredvalue
The error should be less than 30% in every state.
After each test, dosimeter must be cleared. Create new exam to ensure DAP and dose
NOTE show value on workstation be cleared.
Dose value Dose measured
on value on
Collimator field size kV/mA workstation Error
dosimeter
(mGy) (mGy)
60kv/1.3mA
45mm-43mm
110kv/4mA
60kv/1.3mA
110-120mm
110kv/4mA
60kv/1.3mA
140-150mm
110kv/4mA
60kv/1.3mA
Largest size
110kv/4mA
3-49
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
2. Find two screw holes on the skin spacer. Remove the skin spacer and then loose two screws on
the tube head cover, which are corresponding to the two screw holes on skin spacer.
3. Install the skin spacer on the cover and tighten the two screws to secure skin spacer to tube
head cover.
3-50
Installation
Plug the cable of two-pedal footswitch to the socket on the right side of the C-Arm interface panel. Verify
that the connector locks in place.
Functional check: Power on the system. Press the left switch to start fluoroscopy in the mode selected.
Press right switch to save an image displayed on the left monitor.
NOTE
After the installation of option parts, please fill in the product locator card for PLC parts
below and mail the cards to local service operation office.
3-51
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3-52
Chapter4. Subsystem
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Display +24V
Standby
Board PDU Board
J2 PJ6
Pin5 Pin5
JR2
Pin3 Pin3
Relay
Pin4 Pin4
JR1 Power On
Motherboard Pin1
PJ5 Control
MX1 DJ?
MP1 Pin 21 Top
Pin20 Pin20 Pin4
Pin 21 Bot.
Pin8 Pin8
DX6
MCB Pin1B16
Pin1B15
J1A4
Pin9 MCB
KVCB
Pin10
Interlock
Loop
4-2
Subsystem
To
workstation
IGBT Fan
DC24 CCD
Mother BD CCU
Camera
DC24 X-ray On Indicator
(WKS)
Up/Down
DC 24 Up/Down
Driver
Actuator
Circuit Line 24VDC
DC+-15
Breaker Filter
Drive
Transformer
Mul Volt.
KV Control BD
Power Distribution_Mainframe
4-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
AC220
Monitor1
AC220
Monitor2
J3
PC
Display adapter
DC+-12/5
PC Frame Grabber
AC220 ATX PS
AC220 AC220 AC220
Interconnect Line UPS Main BD
Cable Filter
SATA HD USB
UPS
Control BD
DC+-12/5 DVD-RW
DC12 Protection
Relay
AC220
Video distributor
DC24 X-Ray
indicator
Power Distribution_Workstation
4-4
Subsystem
4.2. MCB
The MCB (Mainframe Control Board) is located in C-Arm mainframe and is the main control unit in
mainframe. It is responsible for five functions.
- X-ray control: KV, mA and exposure control interfacing with collimator board, filament board, and KV
control board
- Image chain control: control CCU and image intensifier
- User interface: key input and LED display interfacing with display board
- System monitor: check various error and warning
- Communication with workstation
The structure of MCB interface is illustrated in the following diagram.
4-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
For detailed circuit schematics of MCB, please refer to Appendix. MCB consists of 10 function blocks,
which are illuminated as follows.
4-6
Subsystem
4-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
LED list:
Reference Name Description
DAP_Y & DAP_Z. D20 on MCB lights normally, and flickers in
D20 DAPR communication
XRAYOFF & ON & COMMON. D22 lights when "XRAYOFF" & turns off
D22 KON when "ON"
POWER_SECURITY_A. D24 on MCB lights normally, and turns off in
D24 PSCRT error
POWER_OFF_COMMAND & POWER_OFF_RETURN. D26 turns off
D26 POFF normally on MCB
HAND_SWITCH & HAND_SECURITY & REF_HAND_SWT. D28 turns
D28 HAND off when press
D29 SIMO SPI_SIMO. D29 flickers on MCB
THERMAL_SWTICH_A & THERMAL_SWITCH_B.D30 on MCB lights
D30 THM normally, and turns off in overheat error
D31 lights when handswitch or footswitch security line takes effect
D31 SAFE
DAP_A & DAP_B. D33 on MCB turns off normally, and flickers in
D33 DAPT communication
D34 37K 37.5KHZ. D34 is flickering on MCB when 37.5KHZ is available
WK_A & WK_B. D35 on MCB turns off normally, and flickers in
D35 WKT communication
D36 MCU D36 flickers when MCU work well
D37 SOMI SPI_SOMI. D37 flickers on MCB
FRAME_SYNCH. D38 is flickering on MCB when FRAME_SYNCH is
D38 FSYN available
D39 1200 1200HZ. D39 is flickering on MCB when 1200HZ is available
FOOT_SWITCH & FOOT_SECURITY & REF_FOOT_SWT. D41 turns off
D41 FOOT when press
EMERGENCY_SWT & REF_EMERGENCY_SWT. D43 turns off when
D43 EKEY press
DB_INT. D44 lights on MCB when pressing button of control panel
D44 INT
WK_Y & WK_Z. D45 on MCB lights normally, and flickers in
D45 WKR communication
D46 EXPR D46 lights when EXPOSURE command is sent out
D59 3V3 Light lights when +3.3V is available
D60 +15 Light lights when +15V is available
4-8
Subsystem
Test point:
Reference Name Description
TP1 GND Ground
TP2 IBS Image Brightness Signal
TP3 KVC KV control signal to Filament board
TP4 KV-CLB KV control signal used to calibrate mA feedback
TP5 KVO KV control signal to KV control board
TP6 MA+ mA feedback signal without KV calibration
TP7 MA-SMP mA sample signal with KV calibration
TP8 MA-SET mA setting signal
TP9 PREHEAT mA preheat signal
TP10 MAC mA control signal to Filament board
TP11 PI Output of proportional & integral circuit
TP12 MA-A mA control signal without PREHEAT
TP13 PULSE mAS control signal
TP14 MAS mAS pulse signal
TP15 MA-FB mA feedback signal
TP16 IBSOFF IBS offset setting
TP17 MA-OFF mA control signal offset setting
POT:
Reference Name Description
POT1 IBS IBS offset
POT2 MAS mAS signal gain
POT4 MA-OFF mA control signal offset
POT5 MA-GAIN mA control signal gain
POT6 KV KV control signal gain
POT7 MA-FB mA feedback gain
4-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
PWR_ON UP/DOWN
Membrane ControlB
KV_UP mA_DOWN
MX1
SPI MCB
Mother Board
4-10
Subsystem
IGBT
kV control
MCB inverter Monoblock
board
board
Mother board
The inverter provides 40kHz AC power to monoblock. It can control kV value to follow the kV set value.
There are two parts in the inverter: power converter and controller.
Power converter consists of 1 AC-DC converter and 1 DC-AC converter. AC-DC converter includes rectifier
bridge D and DC bus capacitor C1, C2. DC-AC converter includes fuse F, IGBT devices Q1, Q2, Q3, Q4 and
resonant inductor L and resonant capacitor C. Power converter input AC 220V voltage and output 40kHz
variable voltage to monoblock. The serial resonant frequency of L and C is nearly 40kHz.
AC-DC DC-AC
F
Q1 Q3
D C1 C2 L C
AC
AC
Q2 Q4
4-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
The controller mainly consists of kV control board and driver power transformer. The power transformer
provides 4 channel isolation powers to kV control board. Every channel output voltage is 20V AC.
The kV control board will provide the following function and performance.
Send out 4 channel PWM (Pulse Width Modulation) signal for IGBT inverter board
Provide insulated driver signal for IGBT
KV feedback control circuit
KV feedback value output
Exposure control
KV value set
Protect circuit and error signal output
Signals from MCB to KV control board are listed as follows.
Name Description Attribution Scale Comment
SAFETY_EN Safety line for Digital 0/+15V +15V=enable
EXPOSURE_COMMAND
0V=disable
EXPOSURE_COMMAND Exposure command Digital 0/+15V +15V=enable
0V=disable
KV_SET_INPUT KV set value to KV control board Analog 0-6V Unit is 20KV/V
Signals from KV control board to MCB are listed as follows.
Name Description Attribution Scale Comment
KV_LOW_ALM KV too low alarm, lower than 35KV Digital 0/+15V 0V=alarm
KV_HIGH_ALM KV too High alarm, higher than Digital 0/+15V 0V=alarm
120KV
OVERCURRENT_ALM Inverter over current alarm Digital 0/+15V 0V=alarm
IGBT_ERROR_ALM IGBT error alarm Digital 0/+15V 0V=alarm
DC_ERROR_ALM DC Power Bus Error alarm Digital 0/+15V 0V=alarm
KV_UNBALANCE_ALM KV unbalance in two bridges of Digital 0/+15V 0V=alarm
inverter.
KV_FEEDBACK_OUTPUT KV sample value from KV control Analog 0-6V Unit
board 20KV/V
4-12
Subsystem
4-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1200Hz Clock of filament board Digital 0/+15V Used for filament drive signal
(600Hz) generation
MAC Fluoro mA control Analog 3.0- -
signal 5.0V
KVC KV control signal Analog 4-12V Unit V/10KV
4.6. Monoblock
Monoblock can generate X-ray. It mainly consists of high voltage generator and tube insert. All high
voltage components are put into oil box, which can enhance the insulation performance.
Monoblock generates 110kV inside the oil tank. The input voltage changes from 0V to 240V peak value.
High voltage is got from high frequency and high voltage transformer T1. The primary coil is 10T and the
secondary coil is 2500T. So the maximum voltage of secondary side is 60kV peak value at 40kHz.
T1
D1 C1 R1
+kV
D2 C2 R2
{
kV -mA
Inverter Tube
R3
D3 C3
-kV
R4
D4 C4
T2
{
filament
Inverter T3
4-14
Subsystem
Analog signals KV_GND and MA_CAT of sealing board are the anode and cathode of mA current signal
respectively.
There are two temperature measurement circuits in sealing board. One’s output is analog signal
OIL_TEMP.
Technical Specifications:
Nominal high voltage 110 kV
Nominal input power 2.2 kW
Maximum anode heat content 53 kJ
Target material Tungsten
Target angle 10°
Small focal spot 0.6×1.4 mm
Large focal spot 1.4 mm
Filtration equiv. 0.55 mm Al
Anode Stationary
4-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
X-rays can be enabled via the footswitch or the handswitch. Signals from footswitch and handswitch to
MCB are listed in the following charts. Detailed interconnect information, please refer to chapter 2.3.
Signals from handswitch to MCB:
Name Description Attribution Scale Comment
HAND_SWITCH Hand switch Passive Open/Close HAND_SWITCH &
termination REF_HAND_SWT is
connected means
HAND_SWITCH has pressed
HAND_SECURITY Hand security Passive Open/Close HAND_SECURITY &
termination REF_HAND_SWT is
connected means
HAND_SECURITY has
pressed
REF_HAND_SWT Common termination Passive - -
4-16
Subsystem
4-17
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
4.8.1. Overview
The following diagram the image chain pipeline of Brivo850.
X-ray X-ray
X-ray Detection Image Acquisition Image Processing Image Display
Generation Collimator
VLI (kV+)
Exposure
(kV, mA)
Manage Exposure
ABS Servo Manage
Collimator collimates the X-ray beam to the appropriate field size and user’s setting. The x-ray beam
passes through Grid to reduce scattered X-ray photons. Image Intensifier converts this X-ray into lights
for each field size selection, and sends the light to CCD Camera head. CCD Camera head captures the
light image and sends the analog video to CCU. The CCU performs preliminary image processing, and
outputs analog signal to Frame Grabber Card. Frame Grabber card in the workstation reads the analog
signal, register into digital video, and the CPU performs real-time post-processing (Brightness, Contrast,
Edge Enhance, Zoom, and Negate) to be sent to image display. CCU also analyzes the analog input signal,
and outputs an indicator kv+ to MCB; higher kv+ when the X-ray dose is higher than desired, and lower
kv+ when the X-ray dose is lower than desired. With AutoTechnique enabled, MCB S/W converts this
signal into digital signal, and send command to X-ray Generator to increase or decrease kVp/mA
depending on the kv+ value.
4-18
Subsystem
4-19
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Image tube focus B&C Adjust the image tube focusing Meet spatial resolution requirement
The code position can refer to the following Fig of I.I power supply:
4-20
Subsystem
4.8.4. CCD/CCU
N30_PWR20
NDR_ADV0
1 1
J8
2 2 1 23
3 3 J7
J5 J6 1 23
J4
4-21
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
DB9
V4 V3
CH
CH
A
B
24V
DB25
Name Description
CHA Output video channel A
CHB Output video channel B
V3 Sync output
V4 Output video scan conversion (option)
DB9 CCD head connector (FEMALE)
DB25 Commands interface connector (FEMALE)
24V Power Supply 24Vdc
4-22
Subsystem
Command Description
9
ND2 (PIN 1) Motor 2
Vcc (PIN 6) Power Supply 24Vcc
ND1 (PIN 2) Motor 1
ROT (PIN 7) Rotation
1
5
SCAN (PIN 3) Head test
SYNC (PIN 4) Sync signal
VIDEO (PIN 5) Video signal
Vcc +24Vdc
VIDEO
SCAN
SYNC
ROT
ND1
ND2
(SOLDERING VIEW)
FEMALE
5
3
7
9
6
4-23
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1
+KV
14
GND
2
-KV 15
ROT
3
ND FILTER 16
4
ROT
AUTO OFF
17
5 HALF GAIN
NOT USED
18
6
NOT USED
NOT USED
19
7
NOT USED
NOT USED
20
8
NOT USED
ROI
21
9
DRF
INVH
22
10
FREEZE-A INVV
23
11
FREEZE-B
LIH
24
12
X16 FILTER X4 FILTER
25
13
X0 FILTER
X8 FILTER
4-24
Subsystem
ROT IN 16 GND: ANTI CLOCK WISE ROTATION. PIN 15 + PIN 16 TO GND then OPEN:
RESET ROTATION
OPEN: LIVE IMAGE
LIH IN 11
GND: LAST IMAGE HOLD
OPEN: DYNAMIC RECURSIVE FILTER
DRF IN 21
GND: STANDARD RECURSIVE FILTER
X0, X4, X8, X16 FILTERS
NOISE FILTER = 2
ALL OPEN
X0 and X4 to GND DISABLE CIRCULAR MASK
X0 FILTER IN 25 GND: NOISE FILTER = 0
4-25
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
4.8.6. Monitor
Parameter Code Description Setup Criteria
Brightness N/A Image display brightness: Default: 500
500/600/700
Display curve N/A Image display curve: DICOM/CIE/ Default: Gamma2.2
Gamma1.8/Gamma2.0/Gamma2.2
4-26
Subsystem
4.9.1. Computer
The computer mounted in the workstation takes over most of the communication with external devices
and is the main device of workstation. The computer runs Linux system working with image grabber card
and display card.
The computer contains two memory banks (each one is 1GB) and two hard disks (each one is 250GB)
with standard 3.5’ SATA interface. The partitioned SATA hard drive contains Linux system and system
software. The Serial ATA interface provides several advantages over the traditional (parallel) ATA
interface. The primary advantages include:
Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set
any jumpers or other configuration options.
Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
Scalability to higher performance levels.
The Ethernet port can be used to connect DICOM printer. The system operator can use the Ethernet
connector to interface the workstation to a DICOM server through the facility’s computer network. Once
the Workstation is connected to the network, the operator can query the local server to determine if the
desired images are available for download, and then download selected images to the Workstation. The
Workstation can also upload images over the same network connection. Detailed instructions on DICOM
operation are available in the Operator Manual.
Signals from MCB to workstation:
Name Description Attribution Scale
Wk_Y One of two differential signals from MCB to Workstation Differential signal 1.5-5V
Wk_Z The other one of two differential signals from MCB to workstation Differential signal 1.5-5V
Signals from workstation to MCB:
Name Description Attribution Scale Comment
Wk_A One of two differential Differential 1.5-5v
signals from workstation to signal
MCB
Wk_B The other one of two Differential 1.5-5v
differential signals from signal
workstation to MCB
4-27
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
4-28
Subsystem
The mouse is an ambidextrous three-button optical wheel mouse that plugs into a PS2 port.
4-29
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
4-30
Chapter5. Calibration
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
5.1. Overview
The Calibration described herein should be performed each time you replace a major system component.
Perform these tests in sequence that appears in this section if necessary.
The following tools and test equipment are required to complete the calibration.
Standard Tool
Item Tool
1 Oscilloscope Tektronix 2236 or equivalent
2 Multimeter or equivalent
3 Spatial Resolution Tool
4 Lead Apron
5 kV meter
6 Dosimeter
7 Ampere meter or equivalent
8 Ruler longer than 12 inches (30cm)
9 Erasable marker (whiteboard marker)
10 mAs meter
11 Precision flat head screwdriver (3mm or less) to adjust camera iris, focus
12 Transparent adhesive tape, with cutter (or need scissor or knife to cut the tape)
Special Tool
Item Tool GE part number
1 Three copper sheets, each 1mm thick 00-877682-01
2 9-inch BAFT Tool 00-878105-02
3 PWA, MCB extend board, EVR 5326478
The system will produce X-Rays when implementing the following procedures. Take
WARNING appropriate measures and precautions to protect yourself and others from X-Ray
exposure.
You must obey the following steps to guarantee the safe operation of the C-Arm. Improper
CAUTION adjustment may cause premature failure of major system components.
If the generator has not been powered for more than 3 months, perform the generator
CAUTION warm procedure in section 5.5.
5-2
Calibration
5-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
5.2.2. kV Adjustment
1. Remove the C-arm console cover. Check the connection of IGBT board cables.
2. Remove the cover of PCB box. Extend MCB board with MCB extend board. Remove the J46
jumper on MCB extend board. Connect the probes of ampere meter to TP222(+) and TP210(-) on
MCB extend board.
3. Power on the system. Check that DS9, DS10 and DS3 indicators on kV control board light.
4. Hold down Ctrl +Shift+Alt key and press ”E”, ”V”, ”R” keys orderly and quickly to invoke the service
tool. Login service tool with password and click “Exposure management” button. Click
“Calibration” button.
Select “Adjust mA” in the calibration screen. Choose “YES”, “CA1” will display on control panel.
5. Take one shot X-ray exposure by pressing footswitch. Then adjust POT6 on MCB board until TP5
(KVO) on MCB is 4.0V±0.05V.
6. Rotate R40 and R27 on kV control board clockwise to the end.
7. Test the frequency of TP4 on kV control board with Oscilloscope. Adjust R13 to make the
frequency of TP4 is 80kHz±1kHz. (TP6 and TP9 are signal ground.)
5-4
Calibration
8. Test the voltage of TP16 on kV control board with multimeter. The voltage should be 3.15±0.05V.
Otherwise, adjust R109. Clockwise rotation will decrease the voltage value and anticlockwise will
increase the value.
9. Test the voltage of TP17 on kV control board with multimeter. The voltage should be 3.15±0.05V.
Otherwise, adjust R110. Clockwise rotation will decrease the voltage value and anticlockwise will
increase the value.
10. Take exposure. Adjust POT4 on MP4 board to make sure the mA is 2.0±0.5mA.
11. Take exposure and hold on. Measure TP15 on kV control board with multimeter. Adjust R50 on kV
control board to make the voltage is 4.0V±0.5V. Check that DS1 should be light when exposure.
12. Restart system. Check the kV value as the table in 5.2.1. If they are not in specification, adjust R50
on kV control board or go back to step11.
Refer to the drawing below for the test points, indicators and adjustors.
5-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
MCB
To next
page
5-6
Calibration
5-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
kV control board
5-8
Calibration
5-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Take exposure at mA values below in manual normal fluoro mode. The Exposure mA_measure value
should be between the minimum and maximum value in the form below. Otherwise, mA calibration
procedure should be performed until all the mA_measure values meet the requirement in the list.
Exposure mode mA value Setting mA_measure Minimum mA_measure Maximum
(mA) (mA)
Normal Fluoro 0.1mA@45kVp 0.147 0.165
0.8mA@55kVp 0.797 0.941
1.8mA@60kVp 1.713 2.037
3.5mA@80kVp 3.285 3.915
4mA@110kVp 3.78 4.50
HLF 0.2mA@45kVp 0.238 0.274
1.5mA@50kVp 1.428 1.698
3.8mA@60kVp 3.533 4.217
7.0mA@80kVp 6.47 7.73
10.0mA@60kVp 9.175 11.0
12mA@55kVp* 10.99 13.15
*NOTE: If the system is set in 100V input mode, use 12mA@50kVp or lower kVp instead of
12mA@55kVp.
4. Measure the voltage of TP7 (MA-SMP) on MCB board with oscilloscope.
Exposure mA_real =Voltage (TP7) (unitV)*1000/400
The error of Exposure mA_real value should be within ±9% ranges (meter accuracy is not less than
±1%.).
The voltage of TP7 should be in the range of the form below. Otherwise, mA calibration procedure
should be performed until all the voltage values meet the requirement in the list.
Exposure mode mA value setting Voltage (TP7) minimum Voltage (TP7) maximum
(V) (V)
Digital Spot 1mA@45kVp 0.364 0.436
4mA@60kVp 1.456 1.744
8mA@80kVp 2.912 3.488
12mA@110kVp 4.368 5.232
16mA@80kVp 5.824 6.976
5-10
Calibration
To next
page
5-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
5-12
Calibration
5.3.2. mA calibration
Refer to the drawings at the end of this section for the location of the points. Remove J46 jumper on MCB
extend board. Connect the probes of ampere meter to TP222 (+) and TP210 (-) on MCB extend board in
order to make the ampere meter in serial.
1. Power on the system. Adjust POT4 on MCB board to make the voltage of TP17(MA-OFF) is 0V.
2. Short J5 on MCB board. Hold down Ctrl +Shift+Alt key and press ”E”, ”V”, ”R” keys orderly and
quickly to invoke the service tool. Login service tool and click “Exposure management” button.
Click “Calibration” button.
Select “Adjust mA” in the calibration screen. Choose “Yes” and “CA1” will display on control panel.
3. Take exposure and adjust POT4 on MP4 board to make sure the measured mA value is 2.1±
0.05mA. Clockwise rotation will increase the current. And anticlockwise rotation will decrease the
current.
4. Remove jumper on J5 of MCB board. Take exposure and adjust POT 5 on MCB board to make
sure the measurement current is 2.1±0.05mA. Clockwise rotation will increase the current. And
anticlockwise rotation will decrease the current.
5. Short J5 again. Select “Adjust preheat table” in calibration screen of service mode. “CA2”will
display on control panel. Press footswitch or hand switch and hold on until “END END” is
displayed on control panel LED field, which would last for about 20 minutes.
If the footswitch or hand switch is released early, you should press the switch again until the
control panel LED displays “END END”.
If the “ERR ERR” is displayed on the control panel, you should redo the mA calibration procedure
from step1.
6. Make sure the footswitch or hand switch is released. Remove the jumper on J5. Reboot the
system. Take exposure at 80kV, 0.2mA. Check the measured current value should be 0.3±
0.02mA. Otherwise, adjust POT4 on MCB board. Clockwise rotation will increase the current. And
anticlockwise rotation will decrease the current.
5-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7. Take exposure at 80kV, 2mA. Measure TP7 (MA-SMP) on MCB board with oscilloscope. Set
oscilloscope in TRIGGER mode and the trigger level is –250mV. The first pulse wave should be
orthogonal and similar to the picture below:
5-14
Calibration
MCB:
To next
page
5-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
POT5
5-16
Calibration
5-17
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
5. Set the kVp value to 80kVp and take an exposure for 3 minutes.
6. Wait for 5 minutes.
7. Power off the system.
Enabling Display Marks displays 3 iso-centric white circles, and one center crossing.
NOTE Disabling IP Circular Blanking and CCU Circular Blanking shows image outside the
normal display field.
With CCU Circular Blanking disabled, Recursive Factor button will not be effective, and
NOTE the image will show much noise.
With IP Circular Blanking disabled, Image Processing buttons (Brightness, Contrast,
Negate, Edge enhancement) will be effective only within the middle white circle region.
5-18
Calibration
BAFT Installation
1. Put the 9-inch BAFT (Beam Alignment Tool) on top of the Image Intensifier.
2. Orient the tool so that the number 1 and 2 on the BAFT tool is away from the mainframe, number
3 and 4 is on the Mainframe side. (See the picture below)
3. Orient the tool so that the tool sides are aligned with the mounting surface of the Image
Intensifier.
Aligned
in
parallel
4. Set to Mag2 mode, and fully open the collimator, and to make a shot.
5. Check if you can see a full circular image. If camera is not centered, image does not show full
circular image. If collimator is not centered, it will shadow one side of the image boundary. If the
camera or collimator is not in reasonably calibrated position, roughly calibrate them first. Refer to
Section 5.6.3 for Camera Centering, and Section 5.6.4 for Collimator centering.
5-19
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6. Align the BAFT tool to the circular optical field in the image as follows:
a. Loosen the securing screws (4 screws for each horizontal and vertical adjustment).
b. Adjust position adjustment screws (1 screw for each horizontal and vertical adjustment)
on the BAFT tool.
c. Take an exposure and read the BAFT tool’s tick marks on circular optical field boundary.
d. Check if BAFT tool’s tick marks reading is the same in all angles.
e. Tighten the securing screws, after the make X-ray shot, and double check the BAFT
alignment.
8 Securing Screws
2 Alignment Screws
5-20
Calibration
5-21
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
4. The de-centering deviation should be within the range of the values below. (Note: Each ring is
1mm wide with 1mm spacing between rings.)
Mag Mode MAG2
De-centering (mm) ≤3
5-22
Calibration
EMI Shield
Securing Screw
Camera
Securing Screw
EMI Shield
Camera cable
plug-in port is
disassembled
3. Make sure that 4 Camera Alignment Screws are not too loose. If they are loose, tighten all 4
screws with modest torque.
Camera
Alignment
Screws (there
are 4 screws
with 90 degrees
apart)
5-23
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
a. BAFT image center is not aligned with Rotation Center Marking. Need to Shift BAFT
center to the SE (bottom right) direction.
b. Shift the camera to the same direction to shift the BAFT image center, i.e., S.E. (South
East, or bottom right) direction.
c. Make a shot, and confirm the alignment.
6. Perform Camera Centering Verification. Repeat as many time as necessary.
7. When the camera centering verification meets the specification, tighten the 3 Camera Securing
Screws.
Cleanup
1. Erase the Camera Rotation Center marking on the display monitor.
2. When you follow the normal beam alignment procedure, at this stage, you do not need to
reassemble the EMI shield and Camera Cable Port, and I.I. back cover. You may still need to access
the camera head for Camera focus and Camera Iris adjustment.
Recover the workstation setup.
1. Power On the workstation, and wait until the system boot up completes.
2. Press Ctrl+Alt+Shift, and type “E”,”V”,”R” to enter Service Mode.
3. Select User as “Service”, and type password. Click “Login” button.
4. Select Imaging Defaults.
5. Enable IP Circular Mask, enable CCU Circular Mask, disable Display Marks, and press OK.
5-24
Calibration
5-25
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Cleanup
1. When collimator iris/shutter center is adjusted, make sure to tighten all Collimator Iris securing
screws, and Collimator shutter securing screws.
2. Assemble the X-ray tube cover.
3. Remove the BAFT tool from the Image Intensifier
5-26
Calibration
3. If the requirement is not met, you must perform I.I. Field Size Calibration.
A. Size
B. Focus
C. Edge
5-27
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
L2
L1
5-28
Calibration
13. Repeat step 6 to step 12 for MAG1 and MAG2 field size.
14. If the requirements are not met, you must perform Limiting Field Size (Collimator Iris Field Size)
Calibration.
Cleanup
You may leave the mainframe cover open until you finish the rest of the beam alignment calibration.
5-29
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
5. If the ABS Tracking check fails, proceed to Entrance Dose Rate Check and Camera Iris Adjustment.
1. Measure at TP16 (IBSOFF) of MCB board with Multi-meter, and check if you see 0 V. If not, adjust
the trimmer POT1 at MCB board to get 0 V at TP16.
2. Place the dosimeter probe on the I.I. grid center, and secure it with transparent tape.
3. Use 2mm copper to cover the beam path on the X-ray tube, and secure it with tape.
4. Position the C-arm to lateral position.
5. Make an exposure in Auto Fluoroscopy, and wait until the technique stabilizes. Check if the dose
rate is within 4.0 0.3mR/min (35.04 ± 2.63 μGy/min or 2102 ± 157 μGy/hr).
6. If failed, open the Camera head cover, and carefully adjust the camera iris trimmer. Turn
clockwise to decrease the stable dose rate, and counter-clockwise to increase stable dose rate.
5-30
Calibration
7. Make an exposure to make sure the entrance dose rate 4.0mR/min (35.04 μGy/min or 2102
μGy/hr) as close as possible. Repeat as many time as necessary.
Camera Iris
CCW: Close Iris to increase dose rate
CW: Open Iris to decrease dose rate
Camera Focus
8. If failed after many trials, check the kVp and mA calibration, and come back to Camera Iris
Adjustment.
9. When passed, check if the kVp is within 74±4kV. If fails, perform kVp and mA check, and return
back to the Camera Iris adjustment.
10. When passed, remove the dosimeter probe from the I.I., and remove copper from the X-ray tube,
and perform ABS Tracking check.
Cleanup
When you follow the normal beam alignment procedure, at this stage, you do not need to
reassemble the Camera Head Cover. You may still need to access the camera head for Camera focus
adjustment.
5-31
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
~45
4. Select Auto Fluoroscopy mode. Take an exposure, and stop when image is stable. Adjust kVp and
mA if necessary.
5. Read the limiting resolution on the display image. It is the maximum number (lp/mm) where half
of the lines are distinguishable.
6. Verify if the resolution is within the specified value range below.
7. Repeat step 2 to step 6 for MAG1 mode.
8. Repeat step 2 to step 6 for MAG2 mode.
Field Size NORM MAG1 MAG2
5-32
Calibration
3. Make an exposure, and check the resolution again. Repeat as many times as necessary.
4. If the resolution check still fails after many trials, proceed to I.I. Focus adjustment.
Camera Iris
Slowly turn CW or CCW
Camera Focus
Slowly turn CW or CCW
1. Open the I. I. Potentiometer cover, and carefully adjust the I. I. Focus trimmer.
2. Make an exposure, and check the resolution again. Repeat as many times as necessary.
3. Put the I.I. Potentiometer cover back.
A. Size
B. Focus
C. Edge
5-33
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Cleanup
1. After passing, remove the resolution tool from the I.I. Grid.
2. Make sure to re-assembly of all components as the following:
a. Power off the system.
b. Assemble Camera Head Cover.
c. Disconnect Camera Head Cable.
d. Assemble EMI shield by screwing 6 securing screws.
e. Connect Camera Head Cable, and make sure to tighten the securing screw.
f. Assemble the Camera Head Cable Port in the EMI Shield.
g. Assemble the I.I. cover.
h. Power on the system.
7. At contrast level 85 or higher, pass if you do not see the central region darker than the outside.
For example, at contrast 90, the 1st image shows brighter center, and 2nd image shows darker
center. Too much shading makes darker center.
5-34
Calibration
Shading Correction
To prevent CCU/camera damage, make sure that you power off the system first when you
CAUTION
need to remove or insert the CCU power plug.
Camera
Cable DB9 Frame
Sync
5-35
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
<Warning> The following steps are strongly recommended to reduce the Radiation Hazard to the FSE.
a. Position the C-arm so that the X-ray tube is directing away from the Mainframe. This is
important to minimize the radiation hazard of the FEs.
b. Make sure to wear Radiation Protective Garment.
c. If available, locate the mobile Radiation Protective Shield between X-ray tube and
Mainframe.
9. Put 1mm copper on the X-ray tube, and secure it with tape.
10. Make an exposure with Auto Technique on.
11. Turn on the Automatic Brightness& Contrast.
12. Keep the brightness level and manually increase Contrast level to see well on Brightness
uniformity. Adjust the brightness level if necessary.
13. Manually increase contrast to 85.
14. During live X-ray exposures, adjust trimmer R61, R52, R47, and R48 to adjust brightness
uniformity. Keep contrast level 85 and adjust brightness if necessary to see the shading effect.
5-36
Calibration
15. Adjust contrast level 85 or higher, and make sure that the center region is not darker than the
image boundary.
Cleanup
1. Power off the system, and wait for complete shutdown.
2. Disconnect the cables from CCU.
a. Disassemble the CCU from the Mainframe.
b. Assemble CCU cover, and tighten 8 cover screws.
c. Assemble the CCU to the Mainframe, and tighten 3 CCU securing screws to the
Mainframe.
d. Connect the cables to CCU (Power, Camera Cable DB9, Camera Cable DB25, Video, Frame
Sync; reference the picture in step 8 above).
e. Re-assemble the Mainframe Back Cover.
f. Power on the system.
A “dynamic help for keypad function” is available for each menu. It explains the role of each
Key on the OSD menu window, which is currently active.
5-37
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Adjust monitor’s
Contrast
Adjust monitor’s
Backlight.
The monitor is factory calibrated. For DVI-D input we suggest don’t change the contrast
NOTE value, any change of this will change the optimized LUT settings and will lose some of
the image information. We suggest to only adjust the backlight of the monitor if the
luminance is not acceptable.
5-38
Calibration
SETTING1
SETTING2 While choose backlight it will recall factory default
Settings
SETTING3 contrast, brightness, backlight.
User
Accept changes
Quick OSD menu and either save or reject the
Quit OSD changes. If you have reached this menu
menu unintentionally, you can return to the main menu
using the EXIT key.
Reject changes
5-39
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
5-40
Chapter6. Software
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6.1. Overview
Brivo OEC 850 Mobile C-Arm X-ray Product provides service tool in software for the service engineer.
Using the service tool, service engineer can:
Set service ID, language and time zone for system
Get system information
Exposure management
Database Backup and Restore
Set Imaging Defaults
Consistency Check
Import/Export image
Export Config file
Restore Defaults
Search and export system log
Upgrade software
This chapter will describe how to use the service tool and the installation and upgrade procedure for
software.
6-2
Software
Select Service as the user. Input the password. Click “Login” button to enter the main screen of service
tool.
Click “Shut Down” button to shut down the system. Click “Logout” button to return to service tool login
screen.
6-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6-4
Software
6-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6-6
Software
6-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
The skin dose rate in the Dose Group represents the value for conditions of free-in-air irradiation at the
patient skin: 30cm along the beam axis from the image intensifier surface.
1. Two dose groups in normal (standard) fluoro mode
-Normal50: The skin dose rate does not exceed 50mGy/min in standard fluoro mode, such as
Australia, Japan, New Zealand, etc.
-Normal88: The skin dose rate does not exceed 88mGy/min in standard fluoro mode, such as
USA, Germany, etc.
2. Two dose groups in HLF mode:
-HLF50: The skin dose rate does not exceed 50 mGy/min in HLF mode, such as Japan, etc.
-HLF100: The skin dose rate does not exceed 100 mGy/min in HLF mode, such as Australia, Italy,
UK, New Zealand, etc.
For the country, such as USA, if the skin dose rate shall not exceed 176 mGy/min in HLF mode from its
regulatory requirements, the system will use HLF100 in HLF mode because the maximum skin dose rate
of the X-ray tube cannot exceed 100 mGy/min.
3. For some country, its dose limitation should be the combination of the above normal and HLF groups.
For example,
-Australia: Normal50 and HLF100
-China: Normal88 and HLF100
4. For countries or regions that have a higher standard fluoro dose (at the patient skin) rate limit than
USA, the dose limits are set to the same value as for USA.
5. For countries or regions that have a higher HLF dose (at the patient skin) rate limit than USA, the dose
limits are set to the same value as for USA.
6. For countries or regions that do not specify standard fluoro dose at patient skin, the dose limits are set
to the same value as for USA.
7. For countries or regions that do not specify HLF dose at patient skin, the dose limits are set to the
same value as for USA.
HLF scene setting:
Accessible Only In Auto: Enable or disable “HLF mode only accessible in auto mode”. Some
countries or regions, such as certain provincial locations in Australia, may require enabling
it.
Exposure Limit 20 Sec: Enable or disable “HLF terminates after 20 seconds of continuous
exposure”. Some countries or regions, such as Australia or Switzerland, require enabling it.
Auto-return After Exposure: Enable or disable “ The system automatically returns to normal
mode after HLF termination”. Some countries or regions, such as certain provincial
locations in Australia, may require enabling it.
Auto-return After 5min Without X-Ray: Enable or disable “ The system returns from HLF
mode to normal mode if not used for 5 minutes”. Some countries or regions, such as
certain provincial locations in Australia, may require enabling it.
Refer to the following table “Exposure Management Matrix” to set HLF scene setting.
Fluoro Alarm Control:
6-8
Software
Enable or disable X-ray termination function after 9’30’’ fluoro. If this function is enable, when the
continuous fluoroscopy time reaches 9’30’’, X-rays will be terminated automatically.
Refer to the following table “Exposure Management Matrix” to set Fluoro Alarm Control.
Select DAP option to enable or disable DAP function.
Only when the system is equipped with DAP meter, can DAP option be enabled.
NOTE
Calibration:
Fill in DAP calibration coefficient. The value should be from 0.0 to 10.0. Default value is 1.
Fill in Dose calibration coefficient. The value should be from 0.0 to 1.0.
The dose calibration coefficient is used to Dose calibration. Refer to chapter 3.
Click OK button to save the setting. Select Cancel button to leave the screen.
6-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Auto-return
Auto-return After 5min Terminate X-
Countries / Dose Group Accessible Exposure After Without X- Ray After
Regions Option Only In Auto Limit 20 Sec Exposure Ray 9'30" Fluoro
Normal 88
Brunei and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Bulgaria and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Burkina Faso and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Cambodia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Canada and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Chile and HLF 100 Disable Disable Disable Disable Enable
Normal 88
China (P.R.) and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Colombia and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Costa Rica and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Cyprus and HLF 100 Disable Disable Disable Disable Enable
Czech Normal 88
Republic and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Denmark and HLF 100 Disable Disable Disable Disable Enable
Dominican Normal 88
Republic and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Egypt and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Estonia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Finland and HLF 100 Disable Disable Disable Disable Enable
Normal 88
France and HLF 100 Disable Disable Disable Disable Enable
6-10
Software
Auto-return
Auto-return After 5min Terminate X-
Countries / Dose Group Accessible Exposure After Without X- Ray After
Regions Option Only In Auto Limit 20 Sec Exposure Ray 9'30" Fluoro
and HLF 100
Normal 88
Germany and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Greece and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Guatemala and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Honduras and HLF 100 Disable Disable Disable Disable Enable
Hongkong Normal 88
/Macau and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Hungary and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Iceland and HLF 100 Disable Disable Disable Disable Enable
Normal 88
India and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Indonesia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Iraq and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Ireland and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Israel and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Italy and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Jamaica and HLF 100 Disable Disable Disable Disable Enable
Normal 50
Japan and HLF 50 Disable Disable Disable Disable Disable
Normal 88
Jordan and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Kuwait and HLF 100 Disable Disable Disable Disable Enable
6-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Auto-return
Auto-return After 5min Terminate X-
Countries / Dose Group Accessible Exposure After Without X- Ray After
Regions Option Only In Auto Limit 20 Sec Exposure Ray 9'30" Fluoro
Normal 88
Laos and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Latvia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Lebanon and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Libya and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Lithuania and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Liechtenstein and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Luxembourg and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Macedonia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Malaysia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Malta and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Mexico and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Montenegro and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Morocco and HLF 100 Disable Disable Disable Disable Enable
Normal 50
New Zealand and HLF 100 Disable Enable Disable Disable Enable
Normal 88
Netherlands and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Norway and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Oman and HLF 100 Disable Disable Disable Disable Enable
6-12
Software
Auto-return
Auto-return After 5min Terminate X-
Countries / Dose Group Accessible Exposure After Without X- Ray After
Regions Option Only In Auto Limit 20 Sec Exposure Ray 9'30" Fluoro
and HLF 100
Normal 88
Panama and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Paraguay and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Peru and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Philippines and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Poland and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Portugal and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Puerto Rico and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Romania and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Russia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Saudi Arabia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Singapore and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Slovakia and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Slovenia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
South Africa and HLF 100 Disable Disable Disable Disable Enable
Normal 88
South Korea and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Spain and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Sweden and HLF 100 Disable Disable Disable Disable Enable
6-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Auto-return
Auto-return After 5min Terminate X-
Countries / Dose Group Accessible Exposure After Without X- Ray After
Regions Option Only In Auto Limit 20 Sec Exposure Ray 9'30" Fluoro
Normal 88
Switzerland and HLF 100 Disable Enable Disable Disable Enable
Taiwan
(Republic of Normal 88
China) and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Thailand and HLF 100 Disable Disable Disable Disable Disable
Trinidad & Normal 88
Tobago and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Tunisia and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Turkey and HLF 100 Disable Disable Disable Disable Enable
United Arab Normal 88
Emirates and HLF 100 Disable Disable Disable Disable Enable
Normal 88
USA and HLF 100 Disable Disable Disable Disable Disable
United Normal 88
Kingdom and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Uruguay and HLF 100 Disable Disable Disable Disable Enable
Normal 88
Venezuela and HLF 100 Disable Disable Disable Disable Disable
Normal 88
Vietnam and HLF 100 Disable Disable Disable Disable Enable
6-14
Software
You can backup the current database file on this screen. The database file contains patient and exam’s
information. Click “Start backup…” button to save the current database file. A double confirm screen will
pop up. Click “Yes” button to start backup. The process will complete until “Database backup finished.”
message displays. There are two backup files in the system and used by turns.
Click “Start Restore…” button to enter the Database Restore screen. The backup files’ name contain the
time stamp. You can choose a database according to the time. Click Restore button and click “Yes” on the
double confirm screen to start the restore process. The restore will complete until “Database restore
finished.” message displays.
6-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6-16
Software
Image Brightness: Pressing up or down arrow or dragging the block allows you to adjust image
brightness default from 0 to 100.
Image Contrast: Pressing up or down arrow or dragging the block allows you to adjust image
contrast default from 0 to 100.
Black/White Margin: This adjustment shall be made very carefully only when necessary, as it may
affect the overall image quality. Pressing up or down arrow allows you to adjust image margin
from 0 to 50%. Increasing White Margin value may enhance contrast in bright regions, and
increasing Black Margin value may enhance contrast in dark regions. Increasing White Margin
may decrease overall image brightness. Increasing Black Margin may increase overall image
brightness.
Sharpen Power: Select default value of sharpening power from 0-10.
Enable or disable IP circular mask: it is used to assist beam alignment calibration. Make sure it is
set back to the default setting “Enable” after beam alignment.
Enable or disable CCU circular mask: it is used to assist beam alignment calibration. Make sure it
is set back to the default setting “Enable” after beam alignment.
Enable or disable Display Marks: it is used to assist beam alignment calibration. Make sure it is
set back to the default setting “Disable” after beam alignment.
Click “Check” button on the screen, and then click “Yes” button in confirmation screen to start the check
process. The result will be displayed on the frame after the process complete.
6-17
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
NOTE
Brivo OEC 850 only supports USB disks in FAT or FAT32 format.
1. Click “Image Import/Export…” on the main screen. The “Image Import& Export” screen will display.
6-18
Software
2. If you want to import images from USB to local disk, click Import button on the screen. The screen will
show local directory used to save the images in “Copy To” column.
(1) Insert USB disk to USB interface. Click “Copy From” button to select USB devices to copy from.
Choose the device in the USB list and click “OK”.
NOTE Only those images, which are exported from Brivo OEC850 system, can be imported
back.
6-19
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3. If you want to export images from local disk to USB, click export button on the screen. The screen will
show local saved directory to copy from.
(1) Click “Copy To” button. Select USB device as target destination to copy. Choose the device in the
USB list and click OK.
(2) Select the images to copy.
Select All: Used to select all images in the gallery for copying.
Up/Down Arrow: Used to scroll through all preview images. The arrow buttons are only active if
more than sixteen images are retrieved.
(3) Click “Copy” button. Then click “Yes” in confirmation screen to execute a copy operation. Copy
selected images to the designated destination. The process will complete when the message
“Image export finished.” displayed.
6-20
Software
The exported images can’t be viewed in other computer and only can be imported to
NOTE
Brivo OEC850 systems.
The import and export image function is designated for testing or exhibition purpose,
there is no patient information in the exported images.
2
3
6-21
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Search for: Input the key words of the log text in the textbox to search.
Error code: Input the error code displayed on the monitor and control panel to search the log.
Module: Search the log information according to module that the event or failure happened on. The
available options are: computer, software, X-ray exposure and all.
2. Search
Click the button to start the search operation.
3. Page Number
Display the total and current page number of the log. Click the arrows to turn the pages.
4. Log Information
Display the search results of the log. This field will show the error code, Type, sub-system, module,
create date and log text of the log.
5. Reset
Click “Reset” button to clear all selected search option and restore to defaults.
6. Export
Click “Export” button to export log in “.txt” file to USB disk. The export complete with a message “Log
export finished.”.
There are two log files. Each of them is less than 10MB. Log information will be rewrote when the file
size exceeds the limitation.
6-22
Software
6-23
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Click “Delete” button will delete all database records and all images.
WARNING Click “Delete” button will remove all patient information and all images.
6-24
Software
NOTE System will sounds beeps during the whole software installation procedure. And an Error
message01334 will be displayed.
CAUTION You must press key immediately during system booting in step 1 and step8.
1. Turn on the system, during the memory testing, press key on the keyboard to get to BIOS.
6-25
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3. When the BIOS menu shows, use the arrow down button to select the “Advanced BIOS
Features” and then press “Enter”.
6-26
Software
4. Select “First Boot Device” and press “Enter”. Then choose the “CDROM” and press “Enter”.
6-27
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
5. Press the “ ” key and then press “Enter”. This will save your settings, and the system will
reboot. (The system is now set to boot from CD ROM first.)
6-28
Software
6. When the screen display “DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER”, insert the
OS installation CD into the CD/DVD drive of the WS, then press “Enter”.
7. Once you get to the prompt, type in “SG_EVR”. The OS software will then load on the system.
6-29
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8. Once the software installation is complete, CD will be rejected automatically. Remove the CD and
close the CD tray. Click the “reboot” button.
6-30
Software
9. During the memory testing, press key on the keyboard to get to BIOS.
10. Type in “EVR850BJ” , then press “Enter” key.
11. When the BIOS menu shows, use the arrow down button and “Enter” key to select the “Advanced
BIOS Features” and then press “Enter”.
12. Select “First Boot Device” and press “Enter”. Then choose the “HDD-0” and press “Enter”.
6-31
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
13. Press the “ “key and then press “Enter”. This will save your settings, and the system will
reboot. (The system is now set to boot from hard disk first)
14. System will enter GDM desktop with a terminal pop up.
6-32
Software
2.The welcome screen will display. And the serial number of the system from the manufacture will be
displayed automatically.
6-33
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
If the user data is detected on the workstation, the welcome screen will ask you to choose whether retain
user data or not.
6-34
Software
If you want to retain user data, make Option 1 selected and enter OK. Select “Yes” to confirm your
selection and start the Stage 1 process. Select “No” to return back the previous welcome screen.
Select “Not retain the existing user data” will delete all existing data and it cannot be
CAUTION recovered.
6-35
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
If “Retain existing user data” option is selected restoring user data screen will display after the
application packages installed.
6-36
Software
Functional test: Power on the system. The left monitor of workstation will display GE logo screen. The
right monitor will enter into the PATIENT INFORMATION Screen automatically. Perform workstation
operation check defined in section3.6.2.
6-37
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6-38
Software
3. Login the system with “root” account and the password is “install”.
4. System will enter GDM desktop with a terminal pop up.
5. Insert the Application CD to CD/DVD drive of the workstation. Click “Run Command” in the warning
message box.
6-39
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6. The welcome screen will display. And the serial number of the system from the manufacture will be
displayed automatically.
Click “OK” button and the system will ask you to choose whether retain user data or not.
If you want to retain user data, make Option 1 selected and enter OK. Select “No” to return back the
previous welcome screen. Select “Yes” to confirm your selection and start the Stage 1 process.
6-40
Software
7. The stage1 of installation will start. The rest processes will be the same as the installation process
including stage1 and stage 2.
6-41
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6-42
Software
If “Retain existing user data” option is selected restoring user data screen will display after the
application packages installed.
10. At the end of stage2, press “OK” to shut down the system.
Due to C-arm can’t shut down automatically after upgrade process completes, you should press shut
down button on control panel manually.
6-43
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Functional test: Power on the system. The left monitor of workstation will display GE logo screen. The
right monitor will enter into the PATIENT INFORMATION Screen automatically. Perform workstation
operation check in section3.6.2.
6-44
Software
2. Power on the Brivo OEC 850 Mobile C-arm X-ray Product. Press down “Ctrl”, “Shift”, “Alt” keys together
and press ”E”, ”V”, ”R” keys orderly and the service tool can be invoked. Select Service as the user. Input
the password.
6-45
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3. Click “Image Import/Export…” button on main screen. The “Image Import& Export” screen will display.
Click “Import…” button.
6-46
Software
4. Insert USB disk to USB interface. Click “Copy From” button to select USB devices to copy from. Choose
the device in the USB list and click “OK”.
5. Select the image and then click “Copy”. Click “Yes” button in confirmation screen to execute a copy
operation. Import image to local disk. The process will complete with a message: “ Image Import
finished.”.
6. Exit to the main screen of service tool and then shut down the system.
7. Power on the system after 1 minute. On the Patient Information screen, click “Saved Exams…”
button and select the exam, whose Patient Name field is “Only For Test, Only For Test” . Click “OK”
to return to the Patient Information screen.
6-47
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8. Click “Edit” button. Change the Last Name to “SMPTE test pattern” and delete the text in “First
Name” and “M.I.” field. And then click “Exit” button.
9. Press the Image Directory key on the workstation keyboard. Check the image is in the
directory.
6-48
Chapter7. Troubleshooting
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7.1. Overview
This chapter describes messages that appear on the right workstation monitor during system operation.
Messages may indicate any of the following:
Information
Warning Messages
Error Messages
When the error message appears, error code will also displayed on the kV, mA display field on control
panel.
7.3. Messages
Error Message Comments
Type
Code
"Please turn the system off, wait 1 Servant activation fails.
minute, and then restart the system.
00001 Error
If this message persists, call for service.
Code:00001"
"Please turn the system off, wait 1 Memory allocation fails.
minute, and then restart the system.
00002 Error
If this message persists, call for service.
Code:00002"
"Please turn the system off, wait 1 Binding name service fails.
minute, and then restart the system.
00003 Error
If this message persists, call for service.
Code:00003"
7-2
Troubleshooting
7-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-4
Troubleshooting
7-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-6
Troubleshooting
"Please turn the system off, wait 1 Grabber card driver is missing.
minute, and then restart the system.
00615 Error
If this message persists, call for service.
Code:00615"
7-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-8
Troubleshooting
7-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-10
Troubleshooting
7-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-12
Troubleshooting
7-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-14
Troubleshooting
7-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-16
Troubleshooting
7-17
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-18
Troubleshooting
7-19
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-20
Troubleshooting
1. BIOS 2. Linux
3. Linux 4. App
Control Panel
1.MCB Ready 2.MCB & WKS Comm and Exchange information 3.Done
WKS MCB
7-21
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-22
Troubleshooting
7-23
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7-24
Chapter8. Replacement
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8-2
Replacement
8-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
67 5332898 Component, Video distributor for external DVI video output, EVR 1
8-4
Replacement
8-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
NOTE For the 8 parts as below, field engineer must ship the failed parts to Surgery engineering in
China for autopsy in the first year after M3.
Contact:
Zhang Dounan
GE HUALUN Medical Systems Co. Ltd
No. 1 Yongchang North Road,
Beijing Economic & Technological Development Area
Beijing, P.R. China 100176
Tel: 8610-58068888
After the replacement of the four parts below, please fill in the product locator card and
mail it to local service operation office.
8-6
Replacement
The FRU list contains four special tools to be used in calibration or troubleshooting.
8-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8-8
Replacement
8-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
36
65
18
17
66
63(Right side cover)
19
47
46
55
77
63 (Rear cover)
8-10
Replacement
8.3. Replacement
Electrical circuits inside the equipment use voltages that are capable of Causing serious
WARNING injury or death from electrical shock. Use appropriate precautions.
Please use specified fuse.
If the system has power applied, power off the machine and unplug the AC power cord
WARNING from the wall outlet.
NOTE For the parts below, the calibration procedure or some following action should be done
after the replacement. For detail information, please refer to the replacement procedure.
14 5330055 Component, LCD monitor, EVR Brightness and contrast adjustment if necessary
8-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8.3.1. Covers
Never allow anyone to use the system when any C-arm cover is removed. Use extreme
WARNING caution if you intend to troubleshoot the equipment with the covers off and power
applied. Failure to heed this warning may result death, personal injury, or equipment
damage.
C-Arm covers
You must remove the rear cover prior to the front cover.
You can remove the Cross-arm bearing cover, X-ray tube cover and Image Intensifier cover in any order.
Set the brakes before attempting to remove C-Arm covers.
NOTE
Install the covers in reverse sequence (Front cover prior to rear cover). The torque to
NOTE
screw the C-Arm front cover is 2.5Nm. The torque to screw the rear cover is 5.8Nm.
8-12
Replacement
Workstation covers
You must remove these workstation covers in the following sequence:
1. Rear Cover
2. Left and Right lower side covers
3. Front Cover
4. Left and right upper side covers
Follow these steps to remove the workstation covers:
1. Loosen eight screws of the rear cover. Remove the rear cover.
8-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3. Remove the 2 screws on each side of the front cover and 2 screws in the upside of the printer
cabinet as below. Remove the front cover.
5. Remove the screws on each side and remove the left and right upper side covers.
8-14
Replacement
Upper Covers
NOTE Rear cover must be removed before upper covers can be removed.
1. Loose the screws and remove the monitor support cover. If the cover fit is tight, use two palms
impulse upward on each side of the cover with moderate force continuously until the cover is
pulled out.
2. Remove the screws that secure the rear top cover. Remove the rear top cover.
8-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3. Loose the screws on the sheet metal. Then you can remove the sheet metal.
4. Remove all screws that secure the front top cover. And remove the front top cover.
Replace the new top cover kits and install them in reverse sequence. The torque of the screws that
secure the top covers is 2.5Nm.
8-16
Replacement
3. Remove the screws of the cross arm cover and remove the cover.
4. Loosen the screws of the plate cover of the brake and remove the cover.
5. Replace the brake pad assembly.
8-17
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Replace the new wheel. Move the C-arm and verify that the C-arm can move freely.
8-18
Replacement
2. Remove the plate of the wheel. Loose the screws and then remove the cable pusher.
3. Replace the new parts and reassemble the all the parts.
4. Move the C-arm and verify that the C-arm can move freely.
8-19
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Universal truckle with brake (P/N: 5343601) Universal without brake (P/N: 5343599)
3. Move the workstation and verify that the workstation can move freely.
8-20
Replacement
8.3.3. Generator
1. Remove the tube cover.
2. Unplug the cables connected to collimator. Unscrew the three screws that secured the collimator
and remove it.
3. Disconnect the cables. Underlay the generator to prevent it from falling. Loosen the screws and
replace the generator.
Torque to
10.1Nm during
installation
If the X-ray tube is not powered for more than 3 months, it should be warm first according to section 5.5.
8-21
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8.3.4. Collimator
1. Position the C-arm for easy access. Remove the tube cover. Loosen screws and replace the
collimator.
8-22
Replacement
8-23
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8.3.5. PCBs
Collimator control board (MP1 board) (P/N: 5326480)
1. Remove the rear cover of the console and the PCB box cover.
2. Take off the collimator control board (MP1 board) and insert a new one.
8-24
Replacement
Error 01332 may occur when Brivo OEC 850 system boot up with a new MCB installed.
NOTE Please do not shut down the system by pressing the confirm button. Instead, hold down
Ctrl+Shift+Alt key and press ”E”, ”V”, ”R” keys orderly and invoke the service tool first. Then,
refer to the chapter 5 and follow the instructions to finish the calibrate process.
3. Extend the new MP4 board with extend board (5326483). Perform mA check and calibration
(section 5.3), mAs check and calibration (section 5.4) procedure.
4. Remove the extend board. Insert the new MP4 board and lock in place.
5. Perform ABS Tracking check and adjustment (section 5.6.9) procedure in chapter 5.
6. Perform DAP and dose calibration in section 3.7.5.
7. Install the rear cover of C-arm console.
8-25
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
4. Unplug all cables connected to the motherboard and then remove the metal cover.
8-26
Replacement
3. Unscrew the four screws that secured the board. Replace the new kV control board. Connect all
cables.
7. Perform kV (section 5.2), mA (section 5.3) and mAs (section 5.4) check and calibration procedure in
chapter 5.
8. Perform ABS Tracking check and adjustment (section 5.6.7) procedure in chapter 5.
9. Perform DAP and dose calibration in section 3.7.5.
8-27
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3. Disconnect all cables connected to IGBT board and the cables to the fan.
Remain the screws on the board as below after disconnect the cable. Be careful not to break the pins.
4. Loose the screws that secured the IGBT module and replace a new one.
5. Connect all cables to IGBT module according to the labels on the cable and the mark on board.
(Note: C2 to M1,C1 to P1,C4 to M2,C3 to P2,IGBT+ to P2, IGBT- to N2, yellow line to T1,
black line to T2)
6. Reassembly the shield cover and the rear cover of console.
Make sure that all cables are connected before you power on the system. Otherwise, the
WARNING IGBT assembly will be damaged.
7. Power on the system. Take exposure and verify the system works normally.
8-28
Replacement
8-29
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8. The default power supply is AC 220V power input. If your power supply is 110V, adjust the
jumpers (PJ9 and PJ10) according to wiring diagram. Refer to chapter 3.3 for details.
9. Reinstall the covers of console and restart system to confirm system can power on and take
exposure. Check all functions can work normally.
4. Remove four screws that secure Up-down drive board to chassis. Notice that there are four pillar
washers behind the board.
5. Remove old up-down drive board.
6. Install replacement up down drive PCB. Plug the cables to corresponding connectors (J1, J2, J3).
7. Reinstall the covers. Restart system and press lift and down vertical column switches to verify.
8-30
Replacement
3. Loose the screws that secured the board. Remove the board and replace a new one.
4. Functional check: Power on the system. After the booting up process complete, unplug the AC
power cord. Verify that the UPS can supply power to workstation until the system can shut down
completely.
4. Replace a new control panel and connect the cables. Install the C-arm cover.
5. Functional check: Power on the system. Pressing the buttons and verify that relative indicator can
light.
8-31
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
4. You can replace the FRU parts (such as the hard disk, display card, Memory Bank, mother board,
image grabber card and Chassis Power) in the computer.
8-32
Replacement
Chassis Power
Image Grabber card
Mother board
Display Card
Memory Bank
Hard disk
Cut off the binding tie before removing the memory bank. And replace a new one to
NOTE secure the memory bank after the replacement.
Grabber card shall not be installed in the slot beside Display card.
There are two hard disks in the computer. One is data disk, and the other is system disk. During
replacement of the hard disk, please identify the disk by label on the disk. The labels on one end of the
SATA data cables, which marked “SYSTEM” or “DATA”, are used to connect the cable to the corresponding
disk. The other ends of the SATA data cables are connected to SATA ports on the mother board. Connect
system SATA cable to SATA1, data SATA cable to SATA2 and DVD ROM SATA cable to SATA4. After
replacement of either hard disk, you should reinstall both OS and Application software. Refer to
section6.3.1.
SATA
system
SATA
data SATA ports
8-33
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Functional check: Power on the system. After login the Patient information screen, enter the patient
information and verify that you can enter normally. Create a new exam and take exposure. Verify the
system can work normally and the image will display on the left monitor.
If you have replaced the SYSTEM hard disk and backup the user data, you should also verify that the
original user data and images are remain in the system.
Peripheral
According to the drawing attached to the computer to install the mouse (connect to port2), keyboard
(connect to port3) and DVD RW (connect to 16 and 17).
After replacing the mouse, power on the system and move the mouse. Verify that the mouse can
move freely.
After replacing the keyboard, power on the system. Use the keyboard to enter words to Patient
information screen to verify the keyboard.
After replacing the DVD RW, power on the system. Perform CD/DVD check in section 3.6.2.
8-34
Replacement
2. Unplug the cable connected to the indicator. And then remove the four screws on the sheet
metal support of the indicator.
3. Loose the three screws and then you can remove the exposure indicator and replace it with a
new one. Assemble the sheet metal support back onto monitors. Then assemble the strip covers
back.
4. Power on the system and take exposure. Verify that the exposure indicator lights during exposure.
8-35
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8.3.8. Monitors
To prevent monitor power lost, a binding is used to fix the monitor power plug (see the
picture in step6). The binding is provided with the monitor FRU. Make sure the binding
CAUTION is still used after the monitor replacement.
Perform the procedures below to replace the monitors.
1. Loosen the screw and remove the monitor receptacle access cover. Cut the tying strip on power
cable and pull out the two cables. Make mark on cables to identify which monitor they should
connect to.
Strip cover
8-36
Replacement
6. Install the new monitor and reset all parts and cables. Make sure the binding is still used after the
monitor replacement.
Binding
7. Power on the system. The left monitor of workstation will display GE logo screen. The right
monitor will enter into the PATIENT INFORMATION Screen automatically. Perform the brightness
and contrast adjustment in section5.8 if necessary.
The video cable (P/N: 5333061) is used for troubleshooting. Disconnect the DVI cable from the left
monitor. Connect the CCU V4 and left monitor VGA interface with the video cable. Verify if there is
image displayed on left monitor.
8-37
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
To prevent CCU/camera damage, make sure that you power off the system first when
CAUTION you need to remove or insert the CCU power plug.
To prevent ESD damage to both the old and the new CCD Camera and CCU, make sure
CAUTION that you are grounded with a properly functioning write strap before handling any
ESD sensitive electronic components.
NOTE
CCD and CCU are contained in one kit (P/N: 5330063). If one component fails, you have to
replace both CCU and CCD together.
EMI Shield
Securing Screw
Camera
Securing Screw
Camera Head
Cable
Camera cable
plug-in port
disassembled
EMI Shield
8-38
Replacement
Camera
Alignment
Screws (there
are 4 screws
with 90 degrees
apart)
7. Remove the screws, which fasten the weight. And remove the weight. Pay attention to original
mounting direction.
8. Remove 3 Camera fastening screws. And remove the old Camera from the I.I.. Pay attention to
original mounting direction.
9. Remove the EMI Shield by unscrewing 6 screws. Pay attention to original mounting direction.
10. Unwrap and prepare new camera to be assembled immediately in the next step.
NOTE
Be careful not to touch the camera lens or I.I. output lens.
11. Assemble the new Camera on the I.I, and tighten 3 Camera Securing screws. Pay attention to the
mounting direction of camera on I.I.. The camera direction should be as below:
12. Assemble the EMI cover. Pay attention to the direction. Then assemble the weight.
13. Tighten 4 camera adjustment screws with moderate torque.
14. Connect the Camera Head Cable.
8-39
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3 CCU
Securing
Screws
5. Slide the CCU to the left, and pull out the CCU to remove from the Mainframe.
6. Remove the CCU Securing Bracket from the old CCU, and assemble it to the new CCU.
7. Open the new CCU cover.
CCU Securing
Bracket
CCU Cover
opened
N30_PWR20
NDR_ADV0
1 1 J8
2 2 1 23
J7
3 J53 J6 1 23
1
2 R61 R52 R47 R48
3
J4
8-40
Replacement
9. Assemble the new CCU (with CCU cover open) back to the mainframe.
10. Connect the cables back to CCU (V3-FrameSync, CHB-Video, DB9, DB25, 24V Power).
24V - DB25
Power
CHA CHB
-
Vide
DB9 - V3 - V4
o
CameraHead FrameSync
11. Plug in the system power cable, and power on the system.
Step 3. Calibrate the CCU
A. Black level setting
Parameter CODE DESCRIPTION Setup Criteria
40~60mV from CHA respect
BLACK LEVEL R101 Ad just black level pedestal (BOTTOM BLACK).
referring video level
8-41
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
1
+KV 1
2
4 GND
-KV 1
3
5 ROT
ND FILTER 1
4
6 ROT
AUTO OFF
1
5
7 HALF GAIN
NOT USED
1
NOT USED
6
8 NOT USED
1
7
NOT USED 9 NOT USED
2
8
ROI 0 NOT USED
2
9
INVH 1 DRF
2
10
FREEZE-A 2 INVV
2
11
LIH 3 FREEZE-B
2
12
X16 FILTER 4 X4 FILTER
2
13
X8 FILTER 5 X0 FILTER
3. Adjust R106 (AutoKV Window) potentiometer all the way to the left (anti-clock-wise).
4. Adjust R79 (AutoKV Level) potentiometer, so that the KV+ signal (average) becomes –80~0 mV.
5. Adjust POT1 on Mainframe MCB board, so that measured voltage at TP16 on MCB board is 0V.
NOTE From here, follow the whole procedures in Section 5.6. Beam Alignment Procedure.
8-42
Replacement
3. Replace a new I.I. with power supply. Reassemble the CCD camera, EMI cover, weight and all
cables.
4. Perform section 5.6 Beam alignment procedure.
2. Replace the new power supply. Connect the cables and reassembly the I.I. cover.
3. Perform section 5.6 beam alignment procedure.
8-43
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
8.3.11. UPS
1. Remove the rear and front covers of the workstation.
2. Loose the screws that secured UPS assembly.
3. Disconnect the power cable connected to UPS. Use the handle to remove the UPS.
4. Replace a new UPS and reassemble the parts. Connect the cable.
5. Plug the UPS battery connector.
6. Connect the interconnect cable to C-arm. Plug the power cord into appropriate AC receptacle.
Test
Voltage
increase
Overload
Power on On Battery Indicator
indicator
Replace
Voltage battery
Decrease
Off
8-44
Replacement
7. Press and hold UPS “test” button for several seconds to initiate a self-test. The workstation will
start up and enter BIOS. There will be a message to inform that there’s no AC power and need to
shut down.
8. Press “off” button to turn off the UPS.
9. Power on the system. Verify that the system can power on normally. Power off the system. Verify
that the system can shut down with no error.
10. Install all the covers of the workstation.
AC +
_ AC
8-45
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
3. Loose the screws and replace a new transformer. Connect the wires and bind the wires with the
binding tie to make a good layout.
4. Reassemble all the parts.
5. Power on the system and take exposure. Verify that the system can work normally.
Main Transformer (P/N: 5331597)
1. Remove the rear cover of the C-arm. Unscrew the three screws and open the package box.
2. Cut off the binding tie. Disconnect the wires of the transformer, which are connected to J1 and J2.
8-46
Replacement
DC power supply
+15V, -15V and DC power
+5V (P/N: supply +24V
5331598) and +5V (P/N:
5331599)
2. Disconnect all cables connected to the power supply. Loose the screws and replace a new part.
3. Connect the cables according to the labels. Reassemble all parts.
4. Power on the system. Verify that the workstation and C-arm complete software boot and
initialization with no errors reported on their displays.
8-47
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
DC bus
capacitor
CAUTION Do not touch the capacitors unless power has been completely removed and they have
been discharged.
2. Disconnect the cables. Unscrew the secured screw and remove the capacitor.
3. Replace a new one. Reassemble all the parts.
4. Power on the system and take exposure. Verify that the system can work normally.
Resonant Capacitor(P/N:5329281) and DC bus fuse (P/N:5329279)
1. Remove the rear cover of the C-arm. Unscrew the three screws and open the package box.
2. Disconnect the cables connected to the resonant capacitor (P/N: 5329281) or DC bus fuse (P/N:
5329279). Loose the screws and replace a new one.
Resonant
capacitor DC bus fuse
(P/N: 5329281) (P/N: 5329279)
3. Power on the system and take exposure. Verify that the system can work normally.
8-48
Replacement
Breaker
Brivo OEC850 provides 110V breaker (P/N: 5331606) and 220V breaker (P/N: 5331605).
1. Remove the rear cover and front cover of the C-arm. Unplug the cable connected to the circuit
breaker.
2. Loose the screws and remove the breaker. Then replace a new breaker.
3. Connect the cables to the breaker and reassemble the parts.
4. Power on the system. Verify that the workstation and C-arm complete software boot and
initialization with no errors reported on their displays.
8-49
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
The other is on the base near the breaker. You should remove the rear and front covers of the C-arm
console first.
Connect the cable according to the schematic on the filter:
After the replacement, power on the system and take exposure. Verify that the system can work
normally.
Power on Indicator (P/N: 5331604)
1. Remove the rear and front covers of the C-arm console.
2. Unplug the wires connected to the power on indicator.
8-50
Replacement
Workstation
power filter
Loose the screws and remove the mounting. Loose the screws and unplug the wires connected to the
relay mounting. Replace a new one.
Power on the system. Verify that the workstation and C-arm complete software boot and initialization
with no errors reported on their displays. Shut down the system and verify the system can shut down
normally.
8-51
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
NOTE Both old and new interconnect cable were added as FRU. Please note that old cable
failure need order old one, new cable failure need new one.
New interconnect cable, part SN: 5416178 Old interconnect cable, part SN: 5331655
Unscrew the sleeve of the interconnect cable. Cut off the binding tie. Unplug the wires of the cable from
the socket. And then draw the cable out.
Replace a new cable. Insert the wires and make a good wire layout.
Power on the system. Verify that the workstation and C-arm complete software boot and initialization
with no errors reported on their displays. Shut down the system and verify the system can shut down
normally.
8-52
Replacement
Fuse kit
The kit contains 13 kinds of fuse. You can choose the fuse to replace according to the requirement.
Ref. Part number Description Can be used
ASM, Install plate assebmly,
FUSE5, FUSE6 5331602 Misc, fuse model 6.3A, EVR 5330588
EVR (J1 transformer)
ASM, Install plate assebmly,
FUSE3, FUSE4 5331601 MISC, FUSE MODEL 1A, EVR 5330588
EVR (J1 transformer)
Fuse,Fast-Acting,Ampere
F1 5398495 Rating-2.5A,Voltage Rating- 5326482 PWA, mother board, EVR
250V,5x20 mm
8-53
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
2. Loosen 2 screws from horizontal brake handle and remove the handle.
8-54
Replacement
3. Remove the screws of the cross arm cover and remove the cover.
4. Loose the screws and remove the rear plate. Remove the pin in the shaft.
5. Put something (Wood strip or other kind of support) under console to prevent the whole base to
tilt backward.
6. Loosen the screws on cable holder and release the cable. Draw out the C-arm and Cross-arm
assembly slowly.
8-55
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
7. Use something (for example, wood bar) to block up the C-arm. And put something on ground and
on left of base (for example, cardboard). Overturn the C-arm console to left side.
8. Remove the bottom cover under the linear actuator. And then remove the lower pin.
9. Unplug the J3 from the up down drive board. Cut off the 2 wires. Cut off the binding tie and then
draw out the cable from the hole.
8-56
Replacement
10. Open the package box. Remove the screws on the top end of external column, and remove the
side cover. Remove the plug on inner column. Screw a M4 screw (Length is more than 25 mm)
into the screw hold on actuator upper pin and draw the pin out.
12. Replace a new linear actuator and reassemble the parts. Plug the wire into the connector. And
then insert the connector to J3 of the up down drive board.
8-57
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
13. Insert the pin with M4 screw into the hole and check if the pin is in the axis of the linear actuator.
Unscrew the M4 screw and tighten the plug on the hole. Lock the pin on the bottom of the linear
actuator and put the cover back.
14. Turn back the base assembly and reassemble all the parts.
15. Connect the interconnect cable and power on the system. Press the up and down key on control
panel and verify that the C-arm can rise and drop freely.
8-58
Replacement
8.3.14. Switch
Hand switch (P/N: 5331609)
1. Remove the rear and front cover of the C-arm console. Disconnect the cable from the hand
switch.
8-59
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
2. Loose the screws and remove the base and switch. Then replace a new one.
3. Power on the system. Press the emergency switch, vertical column operation will cease and X-
rays will be disabled. Rotate as arrow indication to release the emergency switch. You can
continue to use the system.
8-60
Replacement
8.3.15. Others
Please refer to chapter3 for the replacement of these FRU parts.
Please refer to the information about power cable and plug for related country in below table.
NOTE For different country, FRU setups are different. There are 2 types FRU, one is Cable with
plug, another is Plug. Please find the correct FRU part number.
Part#_Cable
Item Country Part#_Plug Plug Type Voltage
with plug
1 Algeria - 2415149 CEE7 220V
2 Argentina 5407045 - IRAM 2073 220V
3 Australia 5407042 - AS/NZS 3112 230V
4 Austria - 2415149 CEE7 230V
5 Bangladesh - 5399116 BS 1363A 230V
8-61
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Part#_Cable
Item Country Part#_Plug Plug Type Voltage
with plug
6 Belgium - 2415149 CEE7 230V
7 Bolivia - 2415149 CEE7 230V
8 Bosnia - 2415149 CEE7 220V
9 Brazil 5407039 - NBR 14136 127V
10 Brazil - 2415149 CEE7 220V
11 Brunei - 5399116 BS 1363A 240V
12 Bulgaria - 2415149 CEE7 230V
13 Cambodia - 5399116 BS 1363A 230V
14 China 5331651 - GB 1002 220V
15 Chile - 2415149 CEE7 220V
16 Colombia 5408318 - NEMA 5-15P 110V
17 Cyprus - 5399116 BS 1363A 240V
18 Czech Repulblic - 2415149 CEE7 230V
19 Denmark - 2415149 CEE7 230V
20 Denmark 5407037 - AFSNIT 107-2-D1 230V
21 Egypt - 2415149 CEE7 220V
22 Finland - 2415149 CEE7 230V
23 France - 2415149 CEE7 230V
24 Gabon - 2415149 CEE7 220V
25 Germany - 2415149 CEE7 230V
26 Greece - 2415149 CEE7 220V
27 Guatemala 5408318 - NEMA 5-15P 110V
28 Honduras 5408318 - NEMA 5-15P 110V
29 HongKong - 5399115 BS 546 220V
30 HongKong 5331651 - GB 1002 220V
31 HongKong - 5399116 BS 1363A 220V
32 Hungary - 2415149 CEE7 220V
33 Iceland - 2415149 CEE7 230V
34 India - 5399115 BS 546 230V
35 Indonesia - 2415149 CEE7 230V
36 Indonesia - 5399116 BS 1363A 230V
8-62
Replacement
Part#_Cable
Item Country Part#_Plug Plug Type Voltage
with plug
37 Iraq - 5399115 BS 546 230V
38 Iraq - 2415149 CEE7 230V
39 Iraq - 5399116 BS 1363A 230V
40 Ireland - 5399116 BS 1363A 230V
41 Israel 5407050 - SI-32 220V
42 Italy - 2415149 CEE7 230V
43 Jamaica 5408318 - NEMA 5-15P 110V
44 Japan 5407035 - NEMA 5-20P 100V
45 Japan 5407036 - L6-20P 200V
46 Jordan - 2415149 CEE7 230V
47 Jordan - 5399116 BS 1363A 230V
48 Kenya - 5399116 BS 1363A 240V
49 Kuwait - 5399116 BS 1363A 220V
50 Lebanon - 5399115 BS 546 220V
51 Lebanon - 5399116 BS 1363A 220V
52 Libya - 2415149 CEE7 220V
53 Libya - 5399115 BS 546 220V
54 Luxembourg - 2415149 CEE7 220V
55 Macedonia - 2415149 CEE7 220V
56 Malaysia - 5399116 BS 1363A 240V
57 Malta - 5399115 BS 546 230V
58 Malta - 5399116 BS 1363A 230V
59 Mexico 5408318 - NEMA 5-15P 127V
60 Montenegro - 2415149 CEE7 220V
61 Morocco - 2415149 CEE7 220V
62 New Zealand 5407042 - AS/NZS 3112 230V
63 Nigeria - 5399116 BS 1363A 220V
64 Norway 2415149 CEE7 230V
65 Oman - 2415149 CEE7 240V
66 Oman - 5399115 BS 546 240V
67 Pakistan - 5399115 BS 546 230V
8-63
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Part#_Cable
Item Country Part#_Plug Plug Type Voltage
with plug
68 Panama 5408318 - NEMA 5-15P 120V
69 Paraguay - 2415149 CEE7 220V
70 Peru - 2415149 CEE7 220V
71 Poland - 2415149 CEE7 230V
72 Portugal - 2415149 CEE7 230V
73 Romania - 2415149 CEE7 230V
74 Russia - 2415149 CEE7 220V
75 Saudi Arabia - 5399116 BS 1363A 220V
76 Singapore - 5399115 BS 546 230V
77 Singapore - 5399116 BS 1363A 230V
78 Slovenia - 2415149 CEE7 230V
79 South Africa - 5399115 BS 546 220V
80 South Korea - 2415149 CEE7 220V
81 Spain - 2415149 CEE7 230V
82 Sudan - 5399116 BS 1363A 230V
83 Sweden - 2415149 CEE7 230V
84 Switzerland - 5399117 SEV 1011 230V
85 Taiwan 5408318 - NEMA 5-15P 110V
86 Trinidad & Tobago 5408318 - NEMA 5-15P 115V
87 Tunisia - 2415149 CEE7 220V
88 Turkey - 2415149 CEE7 220V
United Arab
- 5399116 BS 1363A 220V
89 Emirates
90 United Kingdom - 5399116 BS 1363A 230V
91 Uruguay - 2415149 CEE7 220V
92 Venezuela 5408318 - NEMA 5-15P 120V
93 Vietnam - 2415149 CEE7 220V
94 Vietnam - 5399116 BS 1363A 220V
8-64
Chapter9. Periodic Maintenance
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
9.1. Overview
This procedure describes how to conduct performance checks and maintenance procedures. Use the
procedure in conjunction with PM checklist in section 9.2. Follow the procedures in the order they appear
here and record all required information on the checklist.
Serious injury and property damage can result from incorrectly performed service procedures. Observe
all operating and safety procedures in this document.
Procedures should be performed by service personnel specifically trained by GE
WARNING HUALUN Medical Systems, Inc. to calibrate the Brivo OEC 850 C-Arm and Workstation.
9.1.1. Safety
Ingress of Fluids
The system must never be operated or stored in locations where conductive fluids, like
WARNING
water and saline solution, might spill on the equipment.
Always unplug the AC power cable from the wall outlet before cleaning the equipment. Do not allow
water, soap, or other liquids to drip into the equipment and cause short circuits, electric shock and fire
hazards.
Unauthorized Modifications
Under no circumstances should the safety interlock in the system be bypassed, jumped, or otherwise
disabled.
All GE Healthcare systems comply with International Electro Technical Commission safety
standard IEC-60601. Do not connect any external device to the system that does not
NOTE meet the requirements of IEC-60601. Only devices provided or approved by GE HUALUN
Medical Systems, Inc. should be connected to the system.
Motorized Mechanical Operation
The Vertical Column is motorized and should be observed continuously during operation to avoid
pinching or colliding with people and object.
If covers are removed, use extreme care when operating motorized features. Do not carelessly place
objects on the equipment or bump or lean against the equipment. Do not wear loose clothing that may
be caught by mechanical mechanisms. Keep hands and fingers clear of motorized equipment while the
motors are in operation.
Electrical Shock
This system can generate lethal voltages. Practice safe electrical testing
WARNING procedures when performing periodic maintenance procedures.
After taking X-rays, the high voltage cables can retain a lethal charge, even if you
WARNING power down the system. Even though the contacts are recessed, high voltages can
arc several inches from their terminals if the cables are removed from the
connector wells. Use caution when disconnecting high voltage cables even when
9-2
Periodic Maintenance
the power is turned off. If you remove these connections, immediately discharge
their contacts against the high voltage tank case (ground).
X-radiation Exposure
The X-ray tube assembly produces X-radiation when energized. Never operate this device without X-ray
shielding in place. Use lead shielding and draping to protect personnel.
Lead aprons, radiation monitors, and appropriate radiation shields must be utilized
WARNING for the protection of all personnel in the vicinity while performing tests. Living
human anatomy should never be used as a phantom or demonstration aid. Do not
produce radiation in hallways.
Many of the PCB's in this system contain components, which are sensitive to Electro-
CAUTION
Static Discharge (ESD). Observe ESD safety procedures.
9-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
9.2. PM Checklist
Administrative Information
Medical Facility Information Field Service Engineer Information
Hospital or Clinic Name: FSE name:
Address: City:
Employee SSO:
State: Country:
Postal Code/Zip: Contact Person:
Installation Date:
Contact Phone: Department:
System Configuration
Workstation Software Version: MCB Software Version:
Serial Number: Service ID:
Safety Inspection
Antistatic Drag-wires Footswitch cable and pins
Electrical Plug and power cord Ground Continuity
Interconnect Cable and Connector
PC Clean
Yes No
Workstation Checks
Mechanical Movement : Pass Fail Workstation Operation: Pass Fail
9-4
Periodic Maintenance
Copper Filters Specification Measured Adjustment Mag Mode Specification Measured Adjustment
(kVp) (kVp) done? (Field Size) (LP/mm) (LP/mm) done?
1 64 ±4 Yes No NORM (9”) ≥ 2.2 Yes No
Dose Rate
DAP Check
Reporting
Install Equipment Covers Yes No
Reporting complete Yes No
Comments
FSE and Customer sign and date this section when the PM has been completed.
Date Field Service Signature Customer Signature
*NOTE: If the system is set in 100V input mode, use 12mA@50kVp or lower kVp instead of 12mA@55kVp.
9-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
9-6
Periodic Maintenance
2. Connect the Interconnect Cable to the C-Arm and verify continuity between the following:
From To Spec
Screw on the top left corner of the WorkStation AC Power Plug Ground Pin < 0.5
Screw on the tube cover AC Power Plug Ground Pin < 0.5
Screw on the bottom of the Footswitch AC Power Plug Ground Pin < 0.5
9.5. PC Clean
1. Remove the workstation cover.
2. Unplug the cable connected to computer. Take the computer out of the workstation.
3. Remove PC cover
4. Clean the PC outside and inside.
5. Recover the computer cover and put it back into the position. Plug the cable to PC. Recover the
workstation cover.
9-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Perform the following steps with the system powered up and normally booted.
1. Connect the integrated cable in the C-Arm connector and lock it. Connect the Footswitch
cable to the C-Arm.
2. Plug the AC power cord into the receptacle.
3. Press the system on key located on the C-Arm control panel. Verify that the workstation and
C-Arm complete their software boot and initialization with no errors reported on the
workstation and C-Arm displays.
1. Take X-ray exposure and verify the following Image Orientation functions:
2. Press the field size key repeatedly, verifying ability to select any of the three available field
sizes: NORM, MAG1 and MAG2.
3. Press each of the following collimator switches while X-ray exposure. Verify each of the following
collimator functions:
9-8
Periodic Maintenance
5. Press and hold ALARM RESET key for approximately 2 seconds. Verify fluoro time displayed
on the C-arm control panel resets to zero.
6. Check HLF mode as follows:
A. Cover the Image Intensifier with the lead aprons.
B. Take a normal fluoro shot in order allow the kV level to stabilize.
C. Select HLF mode via control panel and take a high-level fluoro shot.
D. Verify that the audible tone beeps at twice the normal rate. Verify that the mA is driven
higher than the normal fluoro at the same kV value.
E. Leave lead aprons in place for next step.
7. Check HLF Pulse Mode as follows:
A. Select PULSE mode via the C-arm control panel. Select a pulse rate of 4 PPS.
B. Take a high-level fluoro shot.
C. Verify that the audible tone beeps at twice the normal rate and the X-ray indicator
flashes at 2 times/3 seconds. Verify that the mA is driven higher than normal Fluoro.
D. Leave lead aprons in place for next step.
8. Assure correct Digital Spot function as follows:
1. Place the X-ray keyswitch in STANDBY position ( ). Press handswitch and verify that no X-rays are
generated. Press Vertical lift button and verify that vertical lift column is not operational.
9-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
2. Place X-ray keyswitch in XRAYOFF position ( ). Press handswitch and verify that no X-rays are
generated. Press vertical lift button and verify the vertical lift column is operational.
3. Place X-ray keyswitch in ON position ( ). Press handswitch, footswitch and vertical lift button to
verify X-ray and vertical lift column are enable.
Emergency Switch
Perform the following test to verify the emergency switch.
1. Press the emergency switch during raising C-arm.
Emergency
Switch
9-10
Periodic Maintenance
Workstation Operation
1. Press SWAP ( ) key and verify this function exchanges images between the left monitor and
the right monitor.
2. Press the SAVE ( ) key and press key. Verify that the left monitor image is previewed in the
Image Directory screen.
3. Verify Patient Information function ( ) activates the Patient Information screen. Enter patient
information. Display scheduled exams, display resume exams screen.
4. Verify Image Directory ( ) function allows you to review, print and archive stored images and
dose information.
9-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
6. Verify ZOOM ( ) function displays a square region of interest (ROI) box and that you can
magnify the ROI.
7. Verify NEGATE ( ) function reverses the light and dark values on the image displayed on the
left monitor.
8. Verify the CONTRAST ( ) function displays and indicator bar and that the amount of
contrast can be increased and decreased.
9. Verify the BRIGHTNESS ( ) function displays an indicator bar and that amount of
brightness can be increased and decreased.
10. Verify that Auto Contrast/Brightness ( ) automatically selects the optimum values of
contrast and brightness.
11. Verify ENGE ENHANCE ( ) function displays an indicator bar and that amount of
enhancement level increased and decreased.
12. Press ALT key and the LOGOUT key ( ) at the same time. Verify that it can log the user out of
the workstation applications. The default password is “123456”.
The logout function can only be available when you select “Require Users to Login” in the
NOTE
“Security” screen. Refer to section 3.6.2.
9-12
Periodic Maintenance
9.7.2. mA Accuracy
Refer to section5.3.1 for mA accuracy check.
9-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
After each test, reset the dosimeter and create a new exam to clear the DAP and dose
NOTE
show value on workstation.
DoseMeasuredvalue Doseshowvalue
ERROR= 100%
DoseMeasuredvalue
If the error is more than 5%, adjust Dose Calibration Coefficient: Login service tool. Enter “Exposure
Management” screen. Change Dose Calibration Coefficient. Dose/Dose rate show value on the
workstation right monitor is in direct proportion with the calibration coefficient.
9-14
Periodic Maintenance
DoseMeasuredvalue Dosevalue(onworkstation )
ERROR= 100%
DoseMeasuredvalue
The error should be less than 30% in every state.
After each test, dosimeter must be cleared. Create new exam to ensure DAP and dose
NOTE show value on workstation be cleared.
NOTE The field size in the form should be measured by field size measure tool.
9-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
9.10. Reporting
9-16
Chapter10. Technical Reference
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10.1. Overview
The policy of GE Healthcare is one of continual product development and improvement.
For this reason, GE Healthcare reserves the right to change the operating characteristics and
specifications of newer products at any time, without prior notice, and without incurring any obligation
relating to previously manufactured items.
The specifications listed are limited to general performance and physical data. Specifications of optional
equipment provided by other manufacturers are given in the applicable manuals provided with those
options.
10-2
Technical Reference
10-3
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10-4
Technical Reference
Weight: 140±10kg
Option Weight
DAP 0.22±0.02kg
Skin Spacer 0.17±0.02kg
Laser Aimer (tube) 0.65±0.06kg
Laser Aimer (Image Intensifier) 2.16±0.2kg
Film Cassette holder 1.4±0.1kg
Video Distributor 2.3±0.2kg
Two-Pedal Footswitch 4±0.4kg
10-5
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10-6
Technical Reference
Value of mAs 1.0, 1.3, 1.6, 2.0, 2.5, 3.2, 4.0, 5.0, 6.3, 8.0, 10, 13,
16, 20, 25, 32, 40, 50, 63, 80 mAs
Pulse Fluoro 1/2/4/8pps
The lowest Current Time Product or the 40kVp, 1mAs
combination of Loading Factors
(mm)
10-7
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10-8
Technical Reference
10.3.4. Collimator
Input power: DC 6V, 0.9W
Electrical connection mode: through DB9.
Mechanical connection mode: cast aluminum bracket, screw fitting
Fluoroscopy
Nominal diameter circle: 23/15/11cm (9”/6”/4.5”)
X-Ray beam continuously adjustable to an area of less than 5×5 cm at the image receptor
Radiography
Nominal diameter circle: 23cm (9”)
10-9
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10.3.5. Others
Semi-transparent shutters
Rotation 180°
Operation Controlled on panel
Grid
Type Circular
Material Carbon fiber
Lines/cm 60
Ratio 10:1
Focus distance 100 cm
Image Intensifier
Type 3 Fields 2 Fields 1 Fields
Input field size 9’’(23 cm) 6’’(15cm) 4.5’’(11cm)
Central resolution ≥51Lp/cm ≥57Lp/cm ≥67Lp/cm
Monitor
Type Monochrome LCD
Size 19’’
Image Storage
Capacity 80,000 images
Size 1K x 1K
Digital Processor
Function Image Processing, Recursive Noise Reduction,
Motion Artifact Reduction, Real-time Edge
Enhancement, Auto Brightness/Contrast,
Brightness/Contrast Adjustment, Negate, Last
Image Hold, Zoom/Roam, Image
Rotation/Reversal/Invert and Swap
10-10
Technical Reference
10-11
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10-12
Technical Reference
10-13
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10-14
Technical Reference
800 000
300W 200W
640 000
480 000
320 000
160 000
0
0 25 50 75 100
Time (minutes)
10-15
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
Patients must be kept as far as possible from the focus, with minimum distance of 20cm.
WARNING
Make sure not to operate when a plastic cover in x-ray assembly is disassembled, which
properly make the distance meet the above requirements.
The operating table matched this equipment should be made of small attenuation
NOTE
equivalent material, otherwise, X-ray dose may be increased.
10-16
Technical Reference
10-17
Brivo OEC 850 Mobile C-Arm X-ray Product Service Manual
10-18
11. Appendix
Brivo OEC 850 Mobile C-Arm X-ray Product
List
Appexdix-2
Circuit Schematics
Appendix- 3
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-4
Circuit Schematics
Appendix- 5
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-6
Circuit Schematics
Appendix- 7
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-8
Circuit Schematics
Appendix- 9
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-10
Circuit Schematics
Appendix- 11
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-12
Circuit Schematics
Appendix- 13
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-14
Circuit Schematics
Appendix- 15
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-16
Circuit Schematics
Appendix- 17
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-18
Circuit Schematics
Appendix- 19
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-20
Circuit Schematics
Appendix- 21
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-22
Circuit Schematics
Appendix- 23
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-24
Circuit Schematics
Appendix- 25
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-26
Circuit Schematics
Appendix- 27
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-28
Circuit Schematics
Appendix- 29
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-30
Circuit Schematics
Appendix- 31
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-32
Circuit Schematics
Appendix- 33
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-34
Circuit Schematics
Appendix- 35
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-36
Circuit Schematics
Appendix- 37
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-38
Circuit Schematics
Appendix- 39
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-40
Circuit Schematics
Appendix- 41
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-42
Circuit Schematics
Appendix- 43
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-44
Circuit Schematics
Appendix- 45
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-46
Circuit Schematics
Appendix- 47
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-48
Circuit Schematics
Appendix- 49
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-50
Circuit Schematics
Appendix- 51
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-52
Circuit Schematics
Appendix- 53
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-54
Circuit Schematics
Appendix- 55
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-56
Circuit Schematics
Appendix- 57
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-58
Circuit Schematics
Appendix- 59
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-60
Circuit Schematics
Appendix- 61
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-62
Circuit Schematics
Appendix- 63
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-64
Circuit Schematics
Appendix- 65
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-66
Circuit Schematics
Appendix- 67
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-68
Circuit Schematics
Appendix- 69
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-70
Circuit Schematics
Appendix- 71
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-72
Circuit Schematics
Appendix- 73
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-74
Circuit Schematics
Appendix- 75
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-76
Circuit Schematics
Appendix- 77
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-78
Circuit Schematics
Appendix- 79
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-80
Circuit Schematics
Appendix- 81
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-82
Circuit Schematics
Appendix- 83
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-84
Circuit Schematics
Appendix- 85
Brivo OEC 850 Mobile C-Arm X-ray Product
Appexdix-86