MX40 Pro LED Display Controller Specifications V1.2.2
MX40 Pro LED Display Controller Specifications V1.2.2
MX40 Pro LED Display Controller Specifications V1.2.2
Specifications
MX40 Pro LED Display Controller Specifications
Change History
Document Version Release Date Description
V1.2.1 2023-03-24 Added support for HDR function for DP and SDI connectors.
V1.1.0 2022-11-07 Updated the description of the USB port on the front panel.
Optimized the description of Ethernet port load capacity.
Introduction
The MX40 Pro is a flagship all-in-one LED display controller with 20 Ethernet ports in the brand-new control system
COEX series of Xi’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar). This controller integrates video
processing and video control into one box and offers rich video input connectors (HDMI 2.0, DP 1.2 and 12G-SDI),
20x Ethernet output ports and 4x 10G optical ports. It can also work with the brand-new software VMP (Vision
Management Platform) to provide a better operation and control experience.
Certifications
CCC, CE, FCC, IC, UKCA, UL, CB
If the product does not have the relevant certifications required by the countries or regions where it is to be
sold, please contact NovaStar to confirm or address the problem. Otherwise, the customer shall be
responsible for the legal risks caused or NovaStar has the right to claim compensation.
Features
www.novastar.tech 1
MX40 Pro LED Display Controller Specifications
Advanced Features
Device Controls
www.novastar.tech 2
MX40 Pro LED Display Controller Specifications
Function Limitation
Frame Rate Adaptive This function can be achieved when the MX40 Pro works with the A10s Pro
receiving card. Currently supported driver ICs include ICND2055, ICND2065,
ICND2069, MBI5253A, MBI5253B, MBI5754B, MBI5264, MBI5264B, MBI5264C,
and CFD555A. In addition, the .ncp file generated by the Cabinet Tool from
NovaStar must be used.
Dynamic Booster This function can be achieved when the MX40 Pro works with the A10s Pro
receiving card. Before operation, brightness and color gamut correction using the
CA410-VP427, CA410-P427 or EYE2-400 color analyzer must be completed.
Full Grayscale Calibration This function can be achieved when the MX40 Pro works with A10s Pro receiving
card. A C3200 camera is required to perform full-grayscale calibration.
3D To use the 3D function, specified 3D glasses are needed. For details, please contact
NovaStar technical support.
Low Latency The Low Latency and Genlock functions are mutually exclusive. To enable low
latency, please make sure all Ethernet ports load the cabinets vertically and share
the same Y coordinate.
HDR The HDR function supports automatic parsing and manual setting. The properties of
12G-SDI sources, DP1.2 sources and non-standard HDR sources can be manually
set to HDR properties. Using the HDR function reduces the MX40 Pro load capacity
by less than half if the MX40 Pro works with the A10s Pro receiving card. For details,
see the Ethernet Port Load Capacity section.
Appearance
Front Panel
Name Description
Standby Button Press the button to power on or power off the device.
Hold down the button for 5s or longer to restart the device.
USB 2.0 Connect to a USB drive only to export the device diagnostic result.
Only the NTFS and FAT32 file systems are supported. Others are not supported.
www.novastar.tech 3
MX40 Pro LED Display Controller Specifications
Name Description
TFT Screen A 3.5-inch screen to display the device status, menus, submenus and messages for
parameter settings
Knob On the home screen, press the knob to enter the main menu screen.
On the main menu screen, rotate the knob to select a menu item or adjust the parameter
value. Press the knob to confirm the operation.
Hold down the knob and BACK button simultaneously for 5s or longer to lock or unlock
the buttons.
Rear Panel
Inputs
HDR Support HDR10 and comply with the SMPTE ST 2084 and
SMPTE ST 2086 standards.
Support HLG.
www.novastar.tech 4
MX40 Pro LED Display Controller Specifications
HDR Support HDR10 and comply with the SMPTE ST 2084 and
SMPTE ST 2086 standards.
Support HLG.
HDR Support HDR10 and comply with the SMPTE ST 2084 and
SMPTE ST 2086 standards.
Support HLG.
HDR Support HDR10 and comply with the SMPTE ST 2084 and
SMPTE ST 2086 standards.
Support HLG.
12G-SDI IN 1 Standards Support ST-2082 (12G), ST-2081 (6G), ST-424 (3G) and ST-292
(HD) standard video inputs.
Support 3G-Level A/Level B (DS mode).
www.novastar.tech 5
MX40 Pro LED Display Controller Specifications
HDR Support HDR10 and comply with the SMPTE ST 2084 and
SMPTE ST 2086 standards.
Support HLG.
Outputs
1–20 20 Gigabit Ethernet output ports. Support hot backup between Ethernet ports.
Max device load capacity: 9 million pixels
The maximum load capacity per Ethernet port is as follows. For details, see the
Ethernet Port Load Capacity section.
− 8bit@60Hz: 659,722 pixels
− 10bit@60Hz: 494,791 pixels (available only with the A10s Pro receiving card)
− 10bit/12bit@60Hz: 329,861 pixels
HDMI 2.0-1 LOOP 1 HDMI loop through. Up to 8 devices can be cabled in one loop.
12G-SDI LOOP 1 SDI loop through. Up to 8 devices can be cabled in one loop.
Controls
ETHERNET 2 Gigabit Ethernet control ports. Support TCP/IP protocol and star topology.
They have the same functions without priority and order, and can be connected to
VMP software. No switch or router is needed to deploy multiple devices on the same
LAN via device cascading as the network switching function is already built in. Up to
20 MX40 Pro devices can be cascaded.
AUX 1 An auxiliary port that connects to the central control device (RS232) (Reserved)
www.novastar.tech 6
MX40 Pro LED Display Controller Specifications
Power
Note
The maximum input resolution and maximum width and height of HDMI and DP connectors must be obtained by
setting the graphics card.
Dimensions
Product Specifications
Electrical Specifications Power input 100-240V~, 50/60Hz, 1.5A
www.novastar.tech 7
MX40 Pro LED Display Controller Specifications
Packing Information Packing box 660.0 mm × 570.0 mm × 210.0 mm, kraft paper box
IP Rating IP20
Please prevent the product from water intrusion and do not wet or wash the product.
The amount of power consumption may vary depending on various factors such as product settings, usage, and
environment.
YCbCr 4:2:2
YCbCr 4:2:2
www.novastar.tech 8
MX40 Pro LED Display Controller Specifications
YCbCr 4:2:2
YCbCr 4:2:2
Note
The maximum resolution of HDMI and DP inputs in the table must be obtained by setting the graphics card.
The formula of calculating the load capacity per Ethernet port and the detailed parameters are as follows.
8bit: Load capacity × 24 × Frame rate < 1000 × 1000 × 1000 × 0.95
10bit: Load capacity × 32 × Frame rate < 1000 × 1000 × 1000 × 0.95
12bit: Load capacity × 48 × Frame rate < 1000 × 1000 × 1000 × 0.95
Max Load Capacity per Ethernet Port (Pixels)
www.novastar.tech 9
MX40 Pro LED Display Controller Specifications
The formula of calculating the load capacity per Ethernet port and the detailed parameters are as follows.
8bit: Load capacity × 24 × Frame rate < 1000 × 1000 × 1000 × 0.95
10bit: Load capacity × 48 ×Frame rate < 1000 × 1000 × 1000 × 0.95
12bit: Load capacity × 48 × Frame rate < 1000 × 1000 × 1000 × 0.95
Max Load Capacity per Ethernet Port (Pixels)
When the product needs to be installed on the rack, 4 screws at least M5*12 should be used to fix it. The rack for
installation shall bear at least 32kg weight.
www.novastar.tech 10
MX40 Pro LED Display Controller Specifications
Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient. Therefore, consideration should be
given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma)
specified by the manufacturer.
Reduced Air Flow – Installation of the equipment in a rack should be such that the amount of air flow required
for safe operation of the equipment is not compromised.
Mechanical Loading – Mounting of the equipment in the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
Circuit Overloading – Consideration should be given to the connection of the equipment to the supply circuit and
the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing this concern.
Reliable Earthing – Reliable earthing of rack-mounted equipment should be maintained. Particular attention
should be given to supply connections other than direct connections to the branch circuit (e.g. use of power
strips).
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Others
This product can only be placed horizontally. Do not mount vertically or upside-down.
This is Class A product. In a domestic environment, this product may cause radio interference in which case the user
may be required to take adequate measures.
www.novastar.tech 11