Professional Documents
Culture Documents
489 Instruction Manual 2006
489 Instruction Manual 2006
g
GE Industrial Systems
489
Generator Management Relay
INSTRUCTION MANUAL
T
GIS ERE
RE
GE Multilin ISO9001:2000
215 Anderson Avenue, Markham, Ontario EM I
G
U LT I L
Canada L6E 1B3
Tel: (905) 294-6222 Fax: (905) 201-2098 GE Multilin's Quality Management
System is registered to
Internet: http://www.GEindustrial.com/multilin ISO9001:2000
QMI # 005094
UL # A3775
Table of Contents
Changing Setpoints
Introduction ......................................................................................................................................... 1-6
The HELP Key ...................................................................................................................................... 1-7
Numerical Setpoints ........................................................................................................................... 1-7
Enumeration Setpoints....................................................................................................................... 1-8
Output Relay Setpoints .................................................................................................................... 1-10
Text Setpoints ................................................................................................................................... 1-10
Installation
Placing the Relay in Service............................................................................................................. 1-11
Testing ............................................................................................................................................... 1-11
INTRODUCTION Overview
Description .......................................................................................................................................... 2-1
Ordering............................................................................................................................................... 2-3
Other Accessories ............................................................................................................................... 2-4
Specifications
Inputs ................................................................................................................................................... 2-5
Outputs ................................................................................................................................................ 2-6
Protection ............................................................................................................................................ 2-6
Digital Inputs ....................................................................................................................................... 2-8
Monitoring ........................................................................................................................................... 2-8
Power Supply ...................................................................................................................................... 2-9
Communications................................................................................................................................. 2-9
Testing ................................................................................................................................................. 2-9
Certification ....................................................................................................................................... 2-10
Physical.............................................................................................................................................. 2-10
Environmental ................................................................................................................................... 2-10
Long-term Storage............................................................................................................................ 2-11
Electrical Installation
Typical Wiring ..................................................................................................................................... 3-8
General Wiring Considerations ......................................................................................................... 3-9
Control Power ..................................................................................................................................... 3-9
Current Inputs ................................................................................................................................... 3-10
Voltage Inputs ................................................................................................................................... 3-12
Digital Inputs ..................................................................................................................................... 3-12
Analog Inputs .................................................................................................................................... 3-12
Analog Outputs ................................................................................................................................. 3-13
RTD Sensor Connections.................................................................................................................. 3-13
Output Relays.................................................................................................................................... 3-14
IRIG-B ................................................................................................................................................. 3-15
RS485 Ports ....................................................................................................................................... 3-15
Dielectric Strength ............................................................................................................................ 3-16
GE Multilin http://www.GEmultilin.com v
489 Table of Contents
Generator Management Relay
SETPOINTS Overview
Setpoint Message Map .......................................................................................................................5-1
Trips / Alarms/ Control Features ........................................................................................................5-6
Relay Assignment Practices ...............................................................................................................5-6
Dual Setpoints .....................................................................................................................................5-7
Commissioning....................................................................................................................................5-7
S1 489 Setup
Passcode ..............................................................................................................................................5-7
Preferences ..........................................................................................................................................5-8
Communications..................................................................................................................................5-9
Real Time Clock .................................................................................................................................5-10
Default Messages ..............................................................................................................................5-11
Message Scratchpad .........................................................................................................................5-12
Clear Data...........................................................................................................................................5-13
S2 System Setup
Current Sensing .................................................................................................................................5-14
Voltage Sensing.................................................................................................................................5-14
Generator Parameters.......................................................................................................................5-15
Serial Start/Stop Initiation.................................................................................................................5-15
vi http://www.GEmultilin.com GE Multilin
Table of Contents 489
Generator Management Relay
S3 Digital Inputs
Description ........................................................................................................................................ 5-16
Breaker Status ................................................................................................................................... 5-16
General Input A to G......................................................................................................................... 5-17
Remote Reset .................................................................................................................................... 5-18
Test Input........................................................................................................................................... 5-18
Thermal Reset ................................................................................................................................... 5-18
Dual Setpoints................................................................................................................................... 5-18
Sequential Trip.................................................................................................................................. 5-19
Field-Breaker ..................................................................................................................................... 5-20
Tachometer ....................................................................................................................................... 5-20
Waveform Capture ........................................................................................................................... 5-21
Ground Switch Status ...................................................................................................................... 5-21
S4 Output Relays
Description ........................................................................................................................................ 5-21
Relay Reset Mode ............................................................................................................................. 5-22
S5 Current Elements
Inverse Time Overcurrent Curve Characteristics ........................................................................... 5-22
Overcurrent Alarm ............................................................................................................................ 5-25
Offline Overcurrent ........................................................................................................................... 5-26
Inadvertent Energization .................................................................................................................. 5-26
Phase Overcurrent ............................................................................................................................ 5-27
Negative Sequence........................................................................................................................... 5-28
Ground Overcurrent ......................................................................................................................... 5-30
Phase Differential.............................................................................................................................. 5-31
Ground Directional ........................................................................................................................... 5-32
High-Set Phase OC............................................................................................................................ 5-33
S6 Voltage Elements
Undervoltage..................................................................................................................................... 5-34
Overvoltage ....................................................................................................................................... 5-35
Volts/Hertz ......................................................................................................................................... 5-36
Phase Reversal .................................................................................................................................. 5-39
Underfrequency ................................................................................................................................ 5-39
Overfrequency................................................................................................................................... 5-40
Neutral Overvoltage ......................................................................................................................... 5-41
Neutral Undervoltage ....................................................................................................................... 5-43
Loss of Excitation.............................................................................................................................. 5-44
Distance Element .............................................................................................................................. 5-45
S7 Power Elements
Power Measurement Conventions .................................................................................................. 5-48
Reactive Power.................................................................................................................................. 5-49
Reverse Power .................................................................................................................................. 5-50
Low Forward Power ......................................................................................................................... 5-51
S8 RTD Temperature
RTD Types ......................................................................................................................................... 5-51
RTDs 1 to 6 ........................................................................................................................................ 5-52
RTDs 7 to 10 ...................................................................................................................................... 5-53
RTD 11................................................................................................................................................ 5-54
RTD 12................................................................................................................................................ 5-54
Open RTD Sensor ............................................................................................................................. 5-55
RTD Short/Low Temp ....................................................................................................................... 5-55
S9 Thermal Model
489 Thermal Model........................................................................................................................... 5-55
Model Setup ...................................................................................................................................... 5-57
Thermal Elements............................................................................................................................. 5-71
S10 Monitoring
Trip Counter ...................................................................................................................................... 5-72
Breaker Failure .................................................................................................................................. 5-72
Trip Coil Monitor............................................................................................................................... 5-72
VT Fuse Failure.................................................................................................................................. 5-73
Demand ............................................................................................................................................. 5-75
Pulse Output...................................................................................................................................... 5-76
Running Hour Setup ......................................................................................................................... 5-77
S12 Testing
Simulation Mode ...............................................................................................................................5-81
Pre-Fault Setup ..................................................................................................................................5-82
Fault Setup .........................................................................................................................................5-83
Test Output Relays ............................................................................................................................5-84
Test Analog Output ...........................................................................................................................5-84
Comm Port Monitor ..........................................................................................................................5-85
Factory Service ..................................................................................................................................5-85
A1 Status
Network Status ....................................................................................................................................6-3
Generator Status .................................................................................................................................6-3
Last Trip Data.......................................................................................................................................6-4
Alarm Status ........................................................................................................................................6-5
Trip Pickups..........................................................................................................................................6-8
Alarm Pickups ....................................................................................................................................6-10
Digital Inputs ......................................................................................................................................6-13
Real Time Clock .................................................................................................................................6-13
A2 Metering Data
Current Metering ...............................................................................................................................6-14
Voltage Metering ...............................................................................................................................6-15
Power Metering .................................................................................................................................6-16
Temperature ......................................................................................................................................6-16
Demand Metering..............................................................................................................................6-17
Analog Inputs.....................................................................................................................................6-17
Speed..................................................................................................................................................6-18
A3 Learned Data
Parameter Averages..........................................................................................................................6-18
RTD Maximums .................................................................................................................................6-18
Analog Input Min/Max.......................................................................................................................6-19
A4 Maintenance
Trip Counters .....................................................................................................................................6-20
General Counters...............................................................................................................................6-22
Timers.................................................................................................................................................6-22
A5 Event Recorder
Event Recorder ..................................................................................................................................6-23
A6 Product Information
489 Model Info ...................................................................................................................................6-25
Calibration Info ..................................................................................................................................6-25
Diagnostics
Diagnostic Messages ........................................................................................................................6-25
Flash Messages .................................................................................................................................6-26
Current Transformers
Ground Fault CTs for 50:0.025 A CT .................................................................................................. 8-7
Ground Fault CTs for 5 A Secondary CT........................................................................................... 8-8
Phase CTs ............................................................................................................................................ 8-9
Revision History
Change Notes.................................................................................................................................... 8-22
Changes to the 489 Manual ............................................................................................................. 8-22
EU Declaration of Conformity
EU Declaration of Conformity......................................................................................................... 8-23
Warranty
GE Multilin Warranty ........................................................................................................................ 8-24
INDEX
GE Multilin http://www.GEmultilin.com ix
489 Table of Contents
Generator Management Relay
x http://www.GEmultilin.com GE Multilin
Important Procedures 489
Generator Management Relay
Getting Started
1 Getting Started
Important Procedures
Cautions and Warnings Please read this chapter to guide you through the initial setup of your new relay.
Before attempting to install or use the relay, it is
imperative that all WARNINGS and CAUTIONS in this
manual are reviewed to help prevent personal injury,
WARNING CAUTION equipment damage, and/or downtime.
Inspection Checklist • Open the relay packaging and inspect the unit for physical damage.
• View the rear nameplate and verify that the correct model has been ordered.
• Ensure that the following items are included:
– Instruction Manual
– GE EnerVista CD (includes software and relay documentation)
– mounting screws
• For product information, instruction manual updates, and the latest software
updates, please visit the GE Multilin website at http://www.GEmultilin.com.
If there is any noticeable physical damage, or any of the contents listed are
missing, please contact GE Multilin immediately.
NOTE
Manual Organization Reading a lengthy instruction manual on a new product is not a task most people
Getting Started
enjoy. To speed things up, this introductory chapter provides guidelines for basic
relay usability. Important wiring considerations and precautions discussed in
Electrical Installation on page 3–8 should be observed for reliable operation.
Detailed information regarding accuracy, output relay contact ratings, and so forth
are detailed in Specifications on page 2–5. The remainder of this manual should be
read and kept for reference to ensure maximum benefit from the 489 Generator
Management Relay. For further information, please consult your local sales
representative or the factory. Comments about new features or modifications for
your specific requirements are welcome and encouraged.
Setpoints and actual values are indicated as follows in the manual:
A4 MAINTENANCE ZV TRIP COUNTERS Z TOTAL NUMBER OF TRIPS
This ‘path representation’ illustrates the location of an specific actual value or
setpoint with regards to its previous menus and sub-menus. In the example above,
the TOTAL NUMBER OF TRIPS actual value is shown to be an item in the TRIP COUNTERS
sub-menu, which itself is an item in the A4 MAINTENANCE menu, which is an item of
ACTUAL VALUES.
Sub-menu levels are entered by pressing the MESSAGE X or ENTER key. When inside a
submenu, the W MESSAGE or ESCAPE key returns to the previous sub-menu. The
MESSAGE T and MESSAGE S keys are used to scroll through the settings in a sub-
menu. The display indicates which keys can be used at any given point.
3. Learned Data:
Getting Started
a. Average magnitudes of generator load, negative-sequence current, and
phase-phase voltage.
b. RTD learned data, which includes the maximum temperature measured by
each of the twelve (12) RTDs.
c. Minimum and maximum values of analog inputs.
4. Maintenance data. This is useful statistical information that may be used for
preventive maintenance. It includes:
a. Trip counters
b. General counters such as number of breaker operations and number of
thermal resets.
c. Generator hours online timer.
5. Event recorder downloading tool.
6. Product information including model number, firmware version, additional
product information, and calibration dates.
7. Oscillography and data logger downloading tool.
Alarm, trip conditions, diagnostics, and system flash messages are grouped under
Target Messages.
Press the MENU key to access the header of each menu, which will be displayed in
the following sequence:
SETPOINTS [Z]
To access setpoints, press the MENU key until the display shows the header of the
setpoints menu, and then press the MESSAGE X or ENTER key to display the header for
the first setpoints page. The setpoint pages are numbered, have an ‘S’ prefix for
easy identification and have a name which provides a general idea of the settings
available in that page. Pressing the MESSAGE T and MESSAGE S keys will scroll through
all the available setpoint page headers. Setpoint page headers look as follows:
SETPOINTS [Z]
S1 489 SETUP
To enter a given setpoints page, press the MESSAGE X or ENTER key. Press the
MESSAGE T or MESSAGE S keys to scroll through sub-page headers until the required
message is reached. The end of a page is indicated by the message END OF PAGE.
The beginning of a page is indicated by the message TOP OF PAGE.
To access actual values, press the MENU key until the display shows the header of the
actual values menu, then press the MESSAGE X or ENTER key to display the header for
the first actual values page. The actual values pages are numbered, have an ‘A’
prefix for easy identification and have a name, which gives a general idea of the
information available in that page. Pressing the MESSAGE T or MESSAGE S keys will
scroll through all the available actual values page headers. Actual values page
headers look as follows:
ACTUAL VALUES [Z]
A1 STATUS
To enter a given actual values page, press the MESSAGE X or ENTER key. Press the
Getting Started
MESSAGE T or MESSAGE S keys to scroll through sub-page headers until the required
message is reached. The end of a page is indicated by the message END OF PAGE.
The beginning of a page is indicated by the message TOP OF PAGE.
Similarly, to access additional sub-pages, press the MESSAGE X or ENTER key to enter
the first sub-page, and then the MESSAGE T or MESSAGE S keys to scroll through the
available sub-pages, until the desired message is reached. The process is identical
for both setpoints and actual values.
The following procedure illustrates the key sequence to access the Current Demand
actual values.
1. Press the MENU key until you reach the actual values main menu.
ACTUAL VALUES [Z]
2. Press MESSAGE X or ENTER key to enter the first actual values page, and then the
MESSAGE T or MESSAGE S key to scroll through pages, until the A2 METERING DATA
page appears.
ACTUAL VALUES [Z]
A2 METERING DATA
3. Press the MESSAGE X or ENTER key to display the first sub-page heading for the
Metering Data actual values page:
CURRENT [Z]
METERING
Pressing the MESSAGE T or MESSAGE S keys will scroll the display up and down
through the sub-page headers. Pressing the W MESSAGE or ESCAPE key at any sub-
page heading will return the display to the heading of the corresponding
setpoint or actual value page, and pressing it again, will return the display to
the main menu header.
4. Press the MESSAGE T key until the DEMAND METERING sub-page heading appears.
DEMAND [Z]
METERING
At this point, pressing MESSAGE X or ENTER key will display the messages under
this sub-page. If instead you press the MESSAGE S key, it will return to the
previous sub-page heading. In this case,
TEMPERATURE [Z]
5. When the symbols and [Z] appear on the top line, it indicates that additional
sub-pages are available and can be accessed by pressing the MESSAGE X or ENTER
key. Pressing MESSAGE X or ENTER while at the Demand Metering sub-page
heading displays the following:
CURRENT
DEMAND: 0 Amps
The menu path to the value shown above is indicated as A2 METERING DATA ZV
Getting Started
DEMAND METERING Z CURRENT DEMAND. Setpoints and actual values messages are
referred to in this manner throughout the manual.
For example, the A4 MAINTENANCE Z TRIP COUNTERS Z TOTAL NUMBER OF TRIPS path
representation describes the following key-press sequence:
1. Press the MENU key until the actual value header appears on the display.
ACTUAL VALUES [Z]
2. Press MESSAGE X or the ENTER key, and then MESSAGE T key until the A4
MAINTENANCE message is displayed.
4. Press the MESSAGE X or ENTER key to reach the TOTAL NUMBER OF TRIPS message
and the corresponding actual value.
TOTAL NUMBER OF
TRIPS: 0
5. Press the MESSAGE T key to display the next actual value message as shown
below:
DIGITAL INPUT
TRIPS: 0
6. Pressing the MESSAGE T or MESSAGE S keys scrolls the display up and down
through all the actual value displays in this corresponding sub-page.
7. Pressing the W MESSAGE key reverses the process described above and returns
the display to the previous level.
TRIP [Z]
COUNTERS
8. Press the W MESSAGE key twice to return to the A4 MAINTENANCE page header.
ACTUAL VALUES [Z]
A4 MAINTENANCE
Panel Keying Example The following figure provides a graphical example of how the keypad is used to
navigate through the menu structure. Specific locations are referred to throughout
this manual by using a ‘path representation’. The example shown in the figure gives
the key presses required to read the average negative-sequence current denoted by
the path A3 LEARNED DATA Z PARAMETER AVERAGES ZV AVERAGE NEG. SEQ. CURRENT.
Press the menu key until the relay displays the actual values page.
Changing Setpoints
Introduction There are several classes of setpoints, each distinguished by the way their values
are displayed and edited.
The relay's menu is arranged in a tree structure. Each setting in the menu is
referred to as a setpoint, and each setpoint in the menu may be accessed as
described in the previous section.
The settings are arranged in pages with each page containing related settings; for
example, all the Phase Overcurrent settings are contained within the same page. As
previously explained, the top menu page of each setting group describes the
settings contained within that page. Pressing the MESSAGE keys allows the user to
move between these top menus.
All of the 489 settings fall into one of following categories: device settings, system
settings, digital input settings, output relay settings, current element settings,
voltage element settings, power element settings, RTD temperature settings,
thermal model settings, monitoring settings, analog input/output settings, and
testing settings.
IMPORTANT NOTE: Settings are stored and used by the relay immediately
after they are entered. As such, caution must be exercised when entering
NOTE settings while the relay is in service. Modifying or storing protection
settings is not recommended when the relay is in service since any
incompatibility or lack of coordination with other previously saved settings
may cause unwanted operations.
Now that we have become more familiar with maneuvering through messages, we
can learn how to edit the values used by all setpoint classes.
Hardware and passcode security features are designed to provide protection against
unauthorized setpoint changes. Since we will be programming new setpoints using
the front panel keys, a hardware jumper must be installed across the setpoint
access terminals (C1 and C2) on the back of the relay case. Attempts to enter a new
setpoint without this electrical connection will result in an error message.
The jumper does not restrict setpoint access via serial communications. The relay
has a programmable passcode setpoint, which may be used to disallow setpoint
changes from both the front panel and the serial communications ports. This
passcode consists of up to eight (8) alphanumeric characters.
The factory default passcode is “0”. When this specific value is programmed into the
Getting Started
relay it has the effect of removing all setpoint modification restrictions. Therefore,
only the setpoint access jumper can be used to restrict setpoint access via the front
panel and there are no restrictions via the communications ports.
When the passcode is programmed to any other value, setpoint access is restricted
for the front panel and all communications ports. Access is not permitted until the
passcode is entered via the keypad or is programmed into a specific register (via
communications). Note that enabling setpoint access on one interface does not
automatically enable access for any of the other interfaces (i.e., the passcode must
be explicitly set in the relay via the interface from which access is desired).
A front panel command can disable setpoint access once all modifications are
complete. For the communications ports, writing an invalid passcode into the
register previously used to enable setpoint access disables access. In addition,
setpoint access is automatically disabled on an interface if no activity is detected for
thirty minutes.
The EnerVista 489 Setup software incorporates a facility for programming the relay
passcode as well as enabling and disabling setpoint access. For example, when an
attempt is made to modify a setpoint but access is restricted, the software will
prompt the user to enter the passcode and send it to the relay before the setpoint is
actually written to the relay. If a SCADA system is used for relay programming, it is
the programmer's responsibility to incorporate appropriate security for the
application.
The HELP Key Pressing the HELP key displays context-sensitive information about setpoints such as
the range of values and the method of changing the setpoint. Help messages will
automatically scroll through all messages currently appropriate.
Numerical Setpoints Each numerical setpoint has its own minimum, maximum, and step value. These
parameters define the acceptable setpoint value range. Two methods of editing and
storing a numerical setpoint value are available.
The first method uses the 489 numeric keypad in the same way as any electronic
calculator. A number is entered one digit at a time with the 0 to 9 and decimal keys.
The left-most digit is entered first and the right-most digit is entered last. Pressing
ESCAPE before the ENTER key returns the original value to the display.
The second method uses the VALUE S key to increment the displayed value by the
step value, up to a maximum allowed value. Likewise, the VALUE T key decrements
the displayed value by the step value, down to a minimum value. For example:
1. Select the S1 489 SETUP ZV PREFERENCES ZV DEFAULT MESSAGE TIMEOUT setpoint
message.
DEFAULT MESSAGE
TIMEOUT: 300 s
2. Press the 1, 2, and 0 keys. The display message will change as shown.
DEFAULT MESSAGE
TIMEOUT: 120 s
3. Until the ENTER key is pressed, editing changes are not registered by the relay.
Therefore, press the ENTER key to store the new value in memory. The following
message will momentarily appear as confirmation of the storing process.
NEW SETPOINT HAS
BEEN STORED
Enumeration Setpoints The example shown in the following figures illustrates the keypress sequences
Getting Started
required to enter system parameters such as the phase CT primary rating, ground
CT primary rating, bus VT connection type, secondary voltage, and VT ratio.
The following values will be entered:
Phase CT primary rating: 600 A
Ground CT type: 1 A secondary
Ground CT ratio: 200:1
Neutral Voltage Transformer: None
Voltage Transformer Connection Type: Open Delta
VT Ratio: 115:1
To set the phase CT primary rating, modify the S2 SYSTEM SETUP Z CURRENT SENSING
Z PHASE CT PRIMARY setpoint as shown below.
Press the MENU key until the relay displays the setpoints menu header.
SETPOINTS [Z]
SETPOINTS [Z]
S1 489 SETUP
Press MESSAGE T
To select the Ground CT type, modify the S2 SYSTEM SETUP Z CURRENT SENSING ZV
GROUND CT setpoint as shown below.
Press the MENU key until the relay displays the setpoints menu header.
SETPOINTS [Z]
SETPOINTS [Z]
S1 489 SETUP
Press MESSAGE T
To set the ground CT ratio, modify the S2 SYSTEM SETUP Z CURRENT SENSING ZV
Getting Started
GROUND CT RATIO setpoint as shown below.
Press the MENU key until the relay displays the setpoints menu header.
SETPOINTS [Z]
SETPOINTS [Z]
S1 489 SETUP
Press MESSAGE T
To set the VT connection type and ratings, modify the S2 SYSTEM SETUP ZV VOLTAGE
SENSING ZV VT CONNECTION TYPE and the S2 SYSTEM SETUP ZV VOLTAGE SENSING ZV
VOLTAGE TRANSFORMER RATIO setpoints as shown below.
Press the MENU key until the relay displays the setpoints menu header.
SETPOINTS [Z]
SETPOINTS [Z]
S1 489 SETUP
Press MESSAGE T
If an entered setpoint value is out of range, the relay displays a message with the
Getting Started
following format:
OUT-OF-RANGE! ENTER: “1-300:1” indicates the range and “0.01:1” indicates the
1-300:1 by 0.01:1 step value
In this case, 1 is the minimum setpoint value, 300 is the maximum, and 0.01 is the
step value. To have access to information on maximum, minimum, and step value,
press the HELP key.
Output Relay Setpoints The output relays 1 Trip and 5 Alarm can be associated to auxiliary relays 2 to 4.
Each can be selected individually, or in combination, in response to customer
specific requirements. These relays are initiated through the ASSIGN ALARM RELAYS or
ASSIGN TRIP RELAYS setpoints specific to a protection element or function.
1. Select the S6 VOLTAGE ELEMENTS Z UNDERVOLTAGE ZV ASSIGN TRIP RELAYS (1-4) set-
point message.
ASSIGN TRIP
RELAYS (1-4): 1---
3. Press the ENTER key to store this change into memory. As before, confirmation of
this action will momentarily flash on the display.
NEW SETPOINT HAS
BEEN STORED
Text Setpoints Text setpoints have data values, which are fixed in length, but user defined in
character. They may be comprised of uppercase letters, lowercase letters, numerals,
and a selection of special characters. The editing and storing of a text value is
accomplished with the use of the decimal [.], VALUE, and ENTER keys.
For example:
1. Move to the S3 DIGITAL INPUTS Z GENERAL INPUT A ZV INPUT NAME message:
INPUT NAME:
Input A
2. The name of this user-defined input will be changed in this example from the
generic “Input A” to something more descriptive.
3. If an application is to be using the relay as a station monitor, it is more
informative to rename this input “Stn. Monitor”. Press the decimal [.] key to
enter the text editing mode. The first character will appear underlined as
follows:
INPUT NAME:
Input A
4. Press the VALUE keys until the character “S” is displayed in the first position. Now
press the decimal [.] key to store the character and advance the cursor to the
next position. Change the second character to a “t” in the same manner.
Continue entering characters in this way until all characters of the text “Stn.
Monitor” are entered. Note that a space is selected like a character. If a
character is entered incorrectly, press the decimal [.] key repeatedly until the
cursor returns to the position of the error. Re-enter the character as required.
Once complete, press the ENTER key to remove the solid cursor and view the
Getting Started
result. Once a character is entered, by pressing the ENTER key, it is automatically
saved in flash memory, as a new setpoint.
INPUT NAME:
Stn. Monitor
Installation
Placing the Relay in The relay is defaulted to the Not Ready state when it leaves the factory. A minor
Service self-test warning message informs the user that the 489 Generator Management
Relay has not yet been programmed. If this warning is ignored, protection will be
active using factory default setpoints and the Relay In Service LED Indicator will be
on.
Testing Extensive commissioning tests are available in Chapter 7. Tables for recording
required settings are available in Microsoft Excel format from the GE Multilin website
at http://www.GEindustrial.com/multilin. The website also contains additional
technical papers and FAQs relevant to the 489 Generator Management Relay.
2 Introduction
Introduction
Overview
Description The 489 Generator Management Relay is a microprocessor-based relay designed for
the protection and management of synchronous and induction generators. The 489
is equipped with 6 output relays for trips and alarms. Generator protection, fault
diagnostics, power metering, and RTU functions are integrated into one economical
drawout package. The single line diagram illustrates the 489 functionality using
ANSI (American National Standards Institute) device numbers.
489
s
ronou
52 Trip Coil
tion
Supervision
Synch
Induc
27
12 overspeed 47
21 distance
59
24 volts/hertz
27 undervoltage 810
50/27 inadvertent generator energization
81U
32 reverse power/low forward power 40
38 bearing overtemperature (RTD) 24
39 bearing vibration (analog inputs) 21
40 loss of excitation (impedance) 32
38
40Q loss of field (reactive power) 41
2
negative sequence overcurrent (I 2 t)
40Q
46 GENERATOR 12
47 voltage phase reversal 50/27
49 stator thermal (RTD/thermal model) 49
51V
50 high-set phase overcurrent 39
50BF breaker failure detection 60FL
50 offline overcurrent 76 Output
46 relays
50/51GN ground overcurrent
51V voltage restrained phase overcurrent 49 6 Output
86 relays
59 overvoltage
50BF
59GN/27TN 100% stator ground
60FL VT fuse failure 50 87G
67 ground directional RS232
76 overexcitation (analog input) RS485
81 overfrequency/underfrequency 67 50/51GN RS485
86 electrical lockout Analog
+ 4
87G percentage differential
59GN 27TN
- outputs
sequential tripping logic +
-
4 Analog
inputs
trip coil supervision
generator running hours alarm
808783E8.CDR
FIGURE 2–1: Single Line Diagram
Fault diagnostics are provided through pretrip data, event record, waveform
capture, and statistics. Prior to issuing a trip, the 489 takes a snapshot of the
measured parameters and stores them in a record with the cause of the trip. This
pre-trip data may be viewed using the NEXT key before the trip is reset, or by
accessing the last trip data in actual values page 1. The event recorder stores a
maximum of 256 time and date stamped events including the pre-trip data. Every
time a trip occurs, the 489 stores a 16 cycle trace for all measured AC quantities.
Trip counters record the number of occurrences of each type of trip. Minimum and
Introduction
maximum values for RTDs and analog inputs are also recorded. These features allow
the operator to pinpoint a problem quickly and with certainty.
A complete list protection features is shown below:
Power metering is a standard feature in the 489. The table below outlines the
metered parameters available to the operator through the front panel and
communications ports. The 489 is equipped with three independent communications
ports. The front panel RS232 port may be used for setpoint programming, local
interrogation or control, and firmware upgrades. The computer RS485 port may be
connected to a PLC, DCS, or PC based interface software. The auxiliary RS485 port
may be used for redundancy or simultaneous interrogation and/or control from a
second PLC, DCS, or PC program. There are also four 4 to 20 mA transducer outputs
Introduction
that may be assigned to any measured parameter. The range of these outputs is
scalable. Additional features are outlined below.
Ordering All features of the 489 are standard, there are no options. The phase CT
secondaries, control power, and analog output range must be specified at the time
of order. There are two ground CT inputs: one for a 50:0.025 CT and one for a
ground CT with a 1 A secondary (may also accommodate a 5 A secondary). The VT
inputs accommodate VTs in either a delta or wye configuration. The output relays
are always non-failsafe with the exception of the service relay. The EnerVista 489
Setup software is provided with each unit. A metal demo case may be ordered for
demonstration or testing purposes.
• Phase CT: 50, 75, 100, 150, 200, 250, 300, 350, 400, 500, 600, 750, 1000
phase CT primaries
• HGF3, HGF5, HGF8: For sensitive ground detection on high resistance
grounded systems
• 489 1 3/8-inch Collar: For shallow switchgear, reduces the depth of the relay
by 1 3/8 inches
• 489 3-inch Collar: For shallow switchgear, reduces the depth of the relay by 3
inches
Specifications
Inputs ANALOG CURRENT INPUTS NEUTRAL VOLTAGE INPUT
Inputs: 0 to 1 mA, 0 to 20 mA, 4 to VT ratio: 1.00 to 240.00:1 in steps of
20mA (setpoint) 0.01
Input impedance: 226 Ω ±10% VT secondary: 100 V AC (full-scale)
Conversion range: 0 to 20 mA Conversion range: 0.005 to 1.00 × Full Scale
Introduction
Accuracy: ±1% of full scale Accuracy: Fundamental:+/-0.5% of Full
Type: Passive Scale
Analog input supply: +24 V DC at 100 mA 3rd Harmonic at >3V
max. secondary: +/-5% of reading
Sampling Interval: 50 ms 3rd Harmonic at < 3V
secondary: +/- 0.15% of full
ANALOG INPUTS FREQUENCY scale
TRACKING Max. continuous: 280 V AC
Frequency tracking: Va for wye, Vab for open
delta; 6 V minimum, 10 Hz/s OUTPUT AND NEUTRAL END
CURRENT INPUTS
DIGITAL INPUTS
CT primary: 10 to 50000 A
Inputs: 9 opto-isolated inputs
CT secondary: 1 A or 5 A (specify with order)
External switch: dry contact < 400 Ω, or open
Conversion range: 0.02 to 20 × CT
collector NPN transistor from
sensor. 6 mA sinking from Accuracy: at < 2 × CT: ±0.5% of 2 × CT
internal 4K pull-up at 24 V DC at ≥ 2 × CT: ±1% of 20 × CT
with Vce < 4 V DC Burden: Less than 0.2 VA at rated load
489 sensor supply: 24 V DC at 20 mA max. CT withstand: 1 s at 80 × rated current
2 s at 40 × rated current
GROUND CURRENT INPUT continuous at 3 × rated current
CT primary: 10 to 10000 A (1 A / 5 A CTs)
CT secondary: 1 A / 5 A or 50:0.025 (HGF PHASE VOLTAGE INPUTS
CTs) VT ratio: 1.00 to 300.00:1 in steps of
0.01
Conversion range:
0.02 to 20 × CT for 1A/5A CTs VT secondary: 200 V AC (full-scale)
0.0 to 100 A primary for Conversion range: 0.02 to 1.00 × full-scale
50:0.025 CTs (HGF) Accuracy: ±0.5% of full-scale
50:0.025 CT accuracy:±0.1 A at < 10 A Max. continuous: 280 V AC
±1.0 A at ≥ 10 to 100 A Burden: > 500 KΩ
1 A / 5 A CT accuracy: RTD INPUTS
at < 2 × CT: ±0.5% of 2 × CT
RTDs (3-wire type):
at ≥ 2 × CT: ±1% of 20 × CT
100 Ω Platinum (DIN.43760)
GROUND CT BURDEN 100 Ω Nickel, 120 Ω Nickel,
Ground CT Input Burden 10 Ω Copper
VA Ω RTD sensing current: 5 mA
Isolation: 36 Vpk
1A/5A 1A 0.024 0.024
(isolated with analog inputs
5A 0.605 0.024 and outputs)
20 A 9.809 0.024 Range: –50 to +250°C
50:0.025 0.025 A 0.057 90.7 Accuracy: ±2°C/±4°F for Pt and Ni
HGF ±5°C/±9°F for Cu
0.1 A 0.634 90.7
Lead resistance: 25 Ω max. per lead (Pt and
0.5 A 18.9 75.6
Ni types); 3 Ω max. per lead
(Cu type)
GROUND CT CURRENT WITHSTAND NO sensor: >1 kΩ
(SECONDARY) Short/low alarm: <–50°C
Ground CT Withstand Time
1 sec. 2 sec. contin
uous
1A/5A 80 × CT 40 × CT 3 × CT
50:0.025 HGF N/A N/A 150 mA
Introduction
time Pickup accuracy: ±0.02 Hz
Elements: Trip and Alarm Timing accuracy: ±100 ms or ±0.5% of total
time
NEUTRAL OVERVOLTAGE
Elements: Trip and Alarm
(FUNDAMENTAL)
Pickup level: 2.0 to 100.0 V secondary in OVERLOAD / STALL PROTECTION /
steps of 0.01 THERMAL MODEL
Time delay: 0.1 to 120.0 s in steps of 0.1 Overload curves:
Pickup accuracy: as per neutral voltage input 15 Standard Overload Curves,
Timing accuracy: ±100 ms or ±0.5% of total Custom Curve, and Voltage
time Dependent Custom Curve (all
Elements: Trip and Alarm curves time out against
average phase current)
NEUTRAL UNDERVOLTAGE Curve biasing: Phase Unbalance, Hot/Cold
(3RD HARMONIC) Curve Ratio, Stator RTD,
Blocking signals: low power and low voltage Online Cooling Rate, Offline
if open delta Cooling Rate, Line Voltage
Pickup level: 0.5 to 20.0 V secondary in Overload pickup: 1.01 to 1.25
steps of 0.01 if open delta VT; Pickup accuracy: as per phase current inputs
adaptive if wye VT Timing accuracy: ±100 ms or ±2% of total
Time delay: 5 to 120 s in steps of 1 time
Pickup accuracy:as per Neutral Voltage Input Elements: Trip and Alarm
Timing accuracy: ±3.0 s
OVERVOLTAGE
Elements: Trip and Alarm
Pickup level: 1.01 to 1.50 × rated V in steps
OFFLINE OVERCURRENT of 0.01
Pickup level: 0.05 to 1.00 × CT in steps of Curve shapes: Inverse Time, definite time
0.01 of any one phase alarm
Time delay: 3 to 99 cycles in steps of 1 Time Delay: 0.2 to 120.0 s in steps of 0.1
Pickup accuracy: as per phase current inputs Pickup accuracy: as per Voltage Inputs
Timing accuracy: +50ms at 50/60 Hz Timing accuracy: ±100 ms or ±0.5% of total
Elements: Trip time
OTHER FEATURES Elements: Trip and Alarm
Serial Start/Stop Initiation, Remote Reset PHASE DIFFERENTIAL
(configurable digital input), Test Input Pickup level: 0.05 to 1.00 × CT in steps of
(configurable digital input), Thermal Reset 0.01
(configurable digital input), Dual Setpoints, Curve shape: Dual Slope
Pre-Trip Data, Event Recorder, Waveform Time delay: 0 to 100 cycles in steps of 1
Memory, Fault Simulation, VT Failure, Trip
Pickup accuracy: as per phase current inputs
Counter, Breaker Failure, Trip Coil Monitor,
Timing accuracy: +50 ms at 50/60 Hz or
Generator Running Hours Alarm, IRIG-B
±0.5% total time
Failure Alarm
Elements: Trip
OVERCURRENT ALARM
Pickup level: 0.10 to 1.50 × FLA in steps of PHASE OVERCURRENT
0.01 (average phase current) Voltage restraint: programmable fixed
characteristic
Time delay: 0.1 to 250.0 s in steps of 0.1
Pickup level: 0.15 to 20.00 × CT in steps of
Pickup accuracy: as per phase current inputs
0.01 of any one phase
Timing accuracy: ±100 ms or ±0.5% of total
Curve shapes: ANSI, IEC, IAC, FlexCurve,
time
Definite Time
Elements: Alarm
Time delay: 0.000 to 100.000 s in steps of
0.001
Pickup accuracy: as per phase current inputs
Timing accuracy: +50 ms at 50/60 Hz or
±0.5% total time
Elements: Trip
RTDS 1 TO 12 UNDERVOLTAGE
Pickup: 1 to 250°C in steps of 1 Pickup level: 0.50 to 0.99 × rated V in steps
Pickup hysteresis: 2°C of 0.01
Time delay: 3 sec. Curve shapes: Inverse Time, definite time
Elements: Trip and Alarm alarm
Time Delay: 0.2 to 120.0 s in steps of 0.1
UNDERFREQUENCY
Pickup accuracy: as per voltage inputs
Required voltage: 0.50 to 0.99 × rated
Timing accuracy: ±100 ms or ±0.5% of total
voltage in Phase A
time
Introduction
Introduction
Elements: Trip and Alarm
POWER METERING
Range: -2000.000 to 2000.000 MW, REVERSE POWER
–2000.000 to 2000.000 Mvar, Block from online: 0 to 5000 s in steps of 1
0 to 2000.000 MVA Pickup level: 0.02 to 0.99 × rated MW
Accuracy at Iavg < 2 × CT: Time delay: 0.2 to 120.0 s in steps of 0.1
±1% of 3 × 2 × CT × VT × VTfull-scale Pickup accuracy: see power metering
Accuracy at Iavg > 2 × CT: Timing accuracy: ±100 ms or ±0.5% of total
±1.5% of 3 × 20 × CT × VT × VTfull-scale time
Elements: Trip and Alarm
TRIP COIL SUPERVISION
Applicable voltage: 20 to 300 V DC/AC
Trickle current: 2 to 5 mA
TESTS!
TYPE TESTING
The table below lists the 489 type tests:
Certification CERTIFICATION
IEC 1010-1: LVD - CE for Europe
EN 50263: EMC - CE for Europe
ACA Tick Mark: RF emissions for Australia
FCC part 15: RF emissions for North
America
UL: listed E83849
ISO 9001: registered
Introduction
environmental factors such as are taken.
moisture or corrosive gases.
It is recommended that all relays be powered up once per year, for one
hour continuously, to avoid deterioration of electrolytic capacitors and
NOTE subsequent relay failure.
3 Installation
Installation
Mechanical Installation
Description The 489 is packaged in the standard GE Multilin SR-series arrangement, which
consists of a drawout unit and a companion fixed case. The case provides
mechanical protection to the unit, and is used to make permanent connections to all
external equipment. The only electrical components mounted in the case are those
required to connect the unit to the external wiring. Connections in the case are
fitted with mechanisms required to allow the safe removal of the relay unit from an
energized panel, such as automatic CT shorting. The unit is mechanically held in the
case by pins on the locking handle, which cannot be fully lowered to the locked
position until the electrical connections are completely mated. Any 489 can be
installed in any 489 case, except for custom manufactured units that are clearly
identified as such on both case and unit, and are equipped with an index pin keying
mechanism to prevent incorrect pairings.
No special ventilation requirements need to be observed during the installation of
the unit, but the unit should be wiped clean with a damp cloth.
Seal location
WARNING
Product Identification Each 489 unit and case are equipped with a permanent label. This label is installed
on the left side (when facing the front of the relay) of both unit and case. The case
label details which units can be installed.
The case label details the model number, manufacture date, and special notes.
The unit label details the model number, type, serial number, file number,
manufacture date, phase current inputs, special notes, overvoltage category,
insulation voltage, pollution degree, control power, and output contact rating.
Installation The 489 case, alone or adjacent to another SR-series unit, can be installed in a
standard 19-inch rack panel (see 489 Dimensions on page 3–1). Provision must be
made for the front door to swing open without interference to, or from, adjacent
equipment. The 489 unit is normally mounted in its case when shipped from the
factory and should be removed before mounting the case in the supporting panel.
Unit withdrawal is described in the next section.
After the mounting hole in the panel has been prepared, slide the 489 case into the
panel from the front. Applying firm pressure on the front to ensure the front bezel
fits snugly against the front of the panel, bend out the pair of retaining tabs (to a
horizontal position) from each side of the case, as shown below. The case is now
securely mounted, ready for panel wiring.
Installation
808704A1.CDR
Unit Withdrawal and TURN OFF CONTROL POWER BEFORE DRAWING OUT OR RE-
Insertion INSERTING THE RELAY TO PREVENT MALOPERATION!
CAUTION
Ethernet Connection If using the 489 with the Ethernet 10Base-T option, ensure that the network cable is
Installation
disconnected from the rear RJ45 connector before removing the unit from the case.
This prevents any damage to the connector.
The unit may also be removed from the case with the network cable connector still
attached to the rear RJ45 connector, provided that there is at least 16 inches of
network cable available when removing the unit from the case. This extra length
allows the network cable to be disconnected from the RJ45 connector from the front
of the switchgear panel. Once disconnected, the cable can be left hanging safely
outside the case for re-inserting the unit back into the case.
The unit may be re-inserted by first connecting the network cable to the rear RJ45
connector of the 489 (see step 3 of Unit Withdrawal and Insertion on page 3–4).
Ensure that the network cable does not get caught inside the case while
sliding in the unit. This may interfere with proper insertion to the case
CAUTION terminal blocks and damage the cable.
NOTE
Terminal Locations
Installation
Installation
A12 RTD #5 Compensation E05 3 Auxiliary NO
A13 RTD Return E06 4 Auxiliary Common
A14 RTD #6 Compensation E07 5 Alarm NC
A15 RTD #6 Hot E08 5 Alarm NO
A16 Analog Output Common – E09 6 Service Common
A17 Analog Output 1 + E10 Neutral VT Common
A18 Analog Output 2 + E11 Coil Supervision +
A19 Analog Output 3 + E12 IRIG-B +
A20 Analog Output 4 + F01 1 Trip Common
A21 Analog Shield F02 2 Auxiliary NO
A22 Analog Input 24 V DC Supply + F03 2 Auxiliary NC
A23 Analog Input 1 + F04 3 Auxiliary Common
A24 Analog Input 2 + F05 4 Auxiliary NO
A25 Analog Input 3 + F06 4 Auxiliary NC
A26 Analog Input 4 + F07 5 Alarm Common
A27 Analog Input Common – F08 6 Service NO
B01 RTD Shield F09 6 Service NC
B02 Auxiliary RS485 + F10 Neutral VT +
B03 Auxiliary RS485 – F11 Coil Supervision –
B04 Auxiliary RS485 Common F12 IRIG-B –
C01 Access + G01 Phase VT Common
C02 Access – G02 Phase A VT •
C03 Breaker Status + G03 Neutral Phase A CT •
C04 Breaker Status – G04 Neutral Phase B CT •
D01 RTD #7 Hot G05 Neutral Phase C CT •
D02 RTD #7 Compensation G06 Output Phase A CT •
D03 RTD Return G07 Output Phase B CT •
D04 RTD #8 Compensation G08 Output Phase C CT •
D05 RTD #8 Hot G09 1A Ground CT •
D06 RTD #9 Hot G10 HGF Ground CT •
D07 RTD #9 Compensation G11 Filter Ground
D08 RTD Return G12 Safety Ground
D09 RTD #10 Compensation H01 Phase B VT •
D10 RTD #10 Hot H02 Phase C VT •
D11 RTD #11 Hot H03 Neutral Phase A CT
D12 RTD #11 Compensation H04 Neutral Phase B CT
D13 RTD Return H05 Neutral Phase C CT
D14 RTD #12 Compensation H06 Output Phase A CT
D15 RTD #12 Hot H07 Output Phase B CT
D16 Assignable Switch 1 H08 Output Phase C CT
D17 Assignable Switch 2 H09 1A Ground CT
D18 Assignable Switch 3 H10 HGF Ground CT
D19 Assignable Switch 4 H11 Control Power –
D20 Assignable Switch 5 H12 Control Power +
Electrical Installation
Typical Wiring
Installation
General Wiring A broad range of applications are available to the user and it is not possible to
Considerations present typical connections for all possible schemes. The information in this section
will cover the important aspects of interconnections, in the general areas of
instrument transformer inputs, other inputs, outputs, communications and
grounding. See Terminal Layout on page 3–6 and 489 Terminal List on page 3–7 for
terminal arrangement, and Typical Wiring Diagram on page 3–8 for typical
connections.
Installation
FIGURE 3–11: Typical Wiring (Detail)
Control Power Control power supplied to the relay must match the installed power
supply range. If the applied voltage does not match, damage to the
CAUTION
unit may occur. All grounds MUST be connected for normal operation
regardless of control power supply type.
The label found on the left side of the relay specifies its order code or model
number. The installed power supply’s operating range will be one of the following.
LO: 20 to 60 V DC or 20 to 48 V AC
HI: 88 to 300 V DC or 70 to 265 V AC
The relay should be connected directly to the ground bus, using the
shortest practical path. A tinned copper, braided, shielding and bonding
CAUTION cable should be used. As a minimum, 96 strands of number 34 AWG should
be used. Belden catalog number 8660 is suitable.
Ensure applied control voltage and rated voltage on drawout case terminal label
match. For example, the HI power supply will work with any DC voltage from 90 to
300 V, or AC voltage from 70 to 265 V. The internal fuse may blow if the applied
voltage exceeds this range.
Extensive filtering and transient protection are built into the 489 to ensure proper
operation in harsh industrial environments. Transient energy must be conducted
back to the source through the filter ground terminal. A separate safety ground
terminal is provided for hi-pot testing.
b) Ground Current
The 489 has a dual primary isolating transformer for ground CT connections. There
are no internal ground connections on the ground current inputs. The ground CT
circuits are shorted by automatic mechanisms on the case if the unit is withdrawn.
The 1 A tap is used for 1 A or 5 A secondary CTs in either core balance or residual
ground configurations. If the 1 A tap is used, the 489 measures up to 20 A
secondary with a maximum ground CT ratio of 10000:1. The ground CT must be
capable of driving the ground CT burden.
The HGF ground CT input is designed for sensitive ground current detection on high
resistance grounded systems where the GE Multilin HGF core balance CT (50:0.025)
is used. In applications such as mines, where earth leakage current must be
measured for personnel safety, primary ground current as low as 0.25 A may be
detected with the GE Multilin HGF CT. Only one ground CT input tap should be used
on a given unit.
The HGF CT has a rating of 50:0.025. However if the HGF CT is used in conjunction
with the 489, the relay assumes a fixed ratio of 5:0.0025. Therefore, the pickup
level in primary amps will be Pickup × CT, where CT is equal to 5.
Only one ground input should be wired. The other input should be unconnected.
NOTE
Installation
FIGURE 3–13: Residual Ground CT Connection
DO NOT INJECT OVER THE RATED CURRENT TO HGF TERMINAL (0.25 to 25
A PRIMARY).
The exact placement of a zero sequence CT to detect ground fault current is shown
CAUTION
below. If the core balance CT is placed over shielded cable, capacitive coupling of
phase current into the cable shield may be detected as ground current unless the
shield wire is also passed through the CT window. Twisted pair cabling on the zero
sequence CT is recommended.
Voltage Inputs The 489 has four voltage transformer inputs, three for generator terminal voltage
and one for neutral voltage. There are no internal fuses or ground connections on
the voltage inputs. The maximum phase VT ratio is 300.00:1 and the maximum
neutral VT ratio is 240.00:1. The two possible VT connections for generator terminal
voltage measurement are open delta or wye (see Typical Wiring Diagram on page
3–8). The voltage channels are connected in wye internally, which means that the
jumper shown on the delta-source connection of the Typical Wiring Diagram,
between the phase B input and the 489 neutral terminal, must be installed for open
delta VTs.
Polarity of the generator terminal VTs is critical for correct power
measurement and voltage phase reversal operation.
CAUTION
Digital Inputs There are 9 digital inputs that are designed for dry contact connections only.
Two of the digital inputs, Access and Breaker Status have their own common
CAUTION
terminal, the balance of the digital inputs share one common terminal (see
Typical Wiring Diagram on page 3–8).
In addition, the +24 V DC switch supply is brought out for control power of an
inductive or capacitive proximity probe. The NPN transistor output could be taken to
one of the assignable digital inputs configured as a counter or tachometer. Refer to
the Specifications section of this manual for maximum current draw from the
+24 V DC switch supply.
DO NOT INJECT VOLTAGES TO DIGITAL INPUTS. DRY CONTACT
CONNECTIONS ONLY.
CAUTION
Analog Inputs Terminals are provided on the 489 for the input of four 0 to 1 mA, 0 to 20 mA, or
4 to 20 mA current signals (field programmable). This current signal can be used to
monitor any external quantity such as: vibration, pressure, field current, etc. The
four inputs share one common return. Polarity of these inputs must be observed for
proper operation The analog input circuitry is isolated as a group with the Analog
Output circuitry and the RTD circuitry. Only one ground reference should be used for
the three circuits. Transorbs limit this isolation to ±36 V with respect to the 489
safety ground.
In addition, the +24 V DC analog input supply is brought out for control power of
loop powered transducers. Refer to the Specifications section of this manual for
maximum current draw from this supply.
Installation
FIGURE 3–16: Loop Powered Transducer Connection
Analog Outputs The 489 provides four analog output channels, which when ordered, provide a full-
scale range of either 0 to 1 mA (into a maximum 10 kΩ impedance), or 4 to 20 mA
(into a maximum 1.2K Ω impedance). Each channel can be configured to provide
full-scale output sensitivity for any range of any measured parameter.
As shown in the Typical Wiring Diagram on page 3–8, these outputs share one
common return. The polarity of these outputs must be observed for proper
operation. Shielded cable should be used, with only one end of the shield grounded,
to minimize noise effects.
The analog output circuitry is isolated as a group with the Analog Input circuitry and
the RTD circuitry. Only one ground reference should be used for the three circuits.
Transorbs limit this isolation to ±36 V with respect to the 489 safety ground.
If a voltage output is required, a burden resistor must be connected at the input of
the SCADA measuring device. Ignoring the input impedance of the input:
V FULL-SCALE
R LOAD = ----------------------------------
- (EQ 3.1)
I MAX
RTD Sensor The 489 can monitor up to 12 RTD inputs for Stator, Bearing, Ambient, or Other
Connections temperature monitoring. The type of each RTD is field programmable as: 100 Ω
Platinum (DIN 43760), 100 Ω Nickel, 120 Ω Nickel, or 10 Ω Copper. RTDs must be
three wire type. Every two RTDs shares a common return.
The 489 RTD circuitry compensates for lead resistance, provided that each of the
three leads is the same length. Lead resistance should not exceed 25 Ω per lead for
platinum and nickel RTDs and 3 Ω per lead for copper RTDs. Shielded cable should
be used to prevent noise pickup in the industrial environment. RTD cables should be
kept close to grounded metal casings and avoid areas of high electromagnetic or
radio interference. RTD leads should not be run adjacent to or in the same conduit
as high current carrying wires.
RTD SENSING
HOT A1 RTD IN
RTD #1
GENERATOR
COMPENSATION A2 STATOR
OR
BEARING
RETURN A3
Output Relays There are six Form-C output relays (see Outputs on page 2–6). Five of the six relays
are always non-failsafe, the 6 Service relay is always failsafe. As a failsafe, the
6 Service relay will be energized normally and de-energize when called upon to
operate. It will also de-energize when control power to the 489 is lost and therefore,
be in its operated state. All other relays, being non-failsafe, will be de-energized
normally and energize when called upon to operate. Obviously, when control power
is lost to the 489, these relays must be de-energized and therefore, they will be in
their non-operated state. Shorting bars in the drawout case ensure that when the
489 is drawn out, no trip or alarm occurs. The 6 Service output will however indicate
that the 489 has been drawn out. Each output relay has an LED indicator on the 489
front panel that comes on while the associated relay is in the operated state.
• 1 TRIP: The trip relay should be wired such that the generator is taken offline
when conditions warrant. For a breaker application, the NO 1 Trip contact
should be wired in series with the Breaker trip coil.
Supervision of a breaker trip coil requires that the supervision circuit be
paralleled with the 1 Trip relay output contacts, as shown in the Typical Wiring
Diagram on page 3–8. With this connection made, the supervision input circuits
will place an impedance across the contacts that will draw a current of 2 to
5 mA (for an external supply voltage from 30 to 250 V DC) through the breaker
trip coil. The supervision circuits respond to a loss of this trickle current as a
failure condition. Circuit breakers equipped with standard control circuits have a
breaker auxiliary contact permitting the trip coil to be energized only when the
breaker is closed. When these contacts are open, as detected by the Breaker
Status digital input, trip coil supervision circuit is automatically disabled. This
logic provides that the trip circuit is monitored only when the breaker is closed.
• 2 AUXILIARY, 3 AUXILIARY, 4 AUXILIARY: The auxiliary relays may be
programmed for numerous functions such as, trip echo, alarm echo, trip
backup, alarm or trip differentiation, control circuitry, etc. They should be wired
as configuration warrants.
• 5 ALARM: The alarm relay should connect to the appropriate annunciator or
monitoring device.
• 6 SERVICE: The service relay will operate if any of the 489 diagnostics detect
an internal failure or on loss of control power. This output may be monitored
with an annunciator, PLC or DCS.
The service relay NC contact may also be wired in parallel with the trip relay on
a breaker application. This will provide failsafe operation of the generator; that
is, the generator will be tripped offline in the event that the 489 is not
protecting it. Simple annunciation of such a failure will allow the operator or the
operation computer to either continue, or do a sequenced shutdown.
Relay contacts must be considered unsafe to touch when the system is energized! If
the customer requires the relay contacts for low voltage accessible applications, it is
WARNING their responsibility to ensure proper insulation levels.
Installation
enabling devices at different geographic locations to be synchronized.
Terminals E12 and F12 on the 489 unit are provided for the connection of an IRIG-B
signal.
RS485 Ports Two independent two-wire RS485 ports are provided. Up to 32 489 relays can be
daisy-chained together on a communication channel without exceeding the driver
capability. For larger systems, additional serial channels must be added. It is also
possible to use commercially available repeaters to increase the number of relays on
a single channel to more than 32. A suitable cable should have a characteristic
impedance of 120 Ω (e.g. Belden #9841) and total wire length should not exceed
4000 feet (approximately 1200 metres). Commercially available repeaters will allow
for transmission distances greater than 4000 ft.
Voltage differences between remote ends of the communication link are not
uncommon. For this reason, surge protection devices are internally installed across
all RS485 terminals. Internally, an isolated power supply with an optocoupled data
interface is used to prevent noise coupling.
To ensure that all devices in a daisy-chain are at the same potential, it is
imperative that the common terminals of each RS485 port are tied together
NOTE and grounded only once, at the master. Failure to do so may result in
intermittent or failed communications.
The source computer/PLC/SCADA system should have similar transient protection
devices installed, either internally or externally, to ensure maximum reliability.
Ground the shield at one point only, as shown below, to avoid ground loops.
Correct polarity is also essential. All 489s must be wired with all ‘+’ terminals
connected together, and all ‘–’ terminals connected together. Each relay must be
daisy-chained to the next one. Avoid star or stub connected configurations. The last
device at each end of the daisy chain should be terminated with a 120 Ω ¼ W
resistor in series with a 1 nF capacitor across the ‘+’ and ‘–’ terminals. Observing
these guidelines will result in a reliable communication system that is immune to
system transients.
Installation
Dielectric Strength It may be required to test a complete motor starter for dielectric strength (“flash” or
hi-pot”) with the 489 installed. The 489 is rated for 1.9 kV AC for 1 second, or 1.6
kV AC for 1 minute (per UL 508) isolation between relay contacts, CT inputs, VT
inputs, trip coil supervision, and the safety ground terminal G12. Some precautions
are required to prevent damage to the 489 during these tests.
Filter networks and transient protection clamps are used between control power, trip
coil supervision, and the filter ground terminal G11. This filtering is intended to filter
out high voltage transients, radio frequency interference (RFI), and electromagnetic
interference (EMI). The filter capacitors and transient suppressors could be
damaged by application continuous high voltage. Disconnect filter ground terminal
G11 during testing of control power and trip coil supervision. CT inputs, VT inputs,
and output relays do not require any special precautions. Low voltage inputs
(<30 V), RTDs, analog inputs, analog outputs, digital inputs, and RS485
communication ports are not to be tested for dielectric strength under any
circumstance (see below).
g GE Multilin
Installation
FIGURE 3–19: Testing the 489 for Dielectric Strength
4 Interfaces
Faceplate Interface
Interfaces
Display All messages appear on a 40-character liquid crystal display. Messages are in plain
English and do not require the aid of an instruction manual for deciphering. When the
user interface is not being used, the display defaults to the user-defined status
messages. Any trip or alarm automatically overrides the default messages and is
immediately displayed.
LED Indicators There are three groups of LED indicators. They are 489 Status, Generator Status, and
Output Status.
808732A3.CDR
FIGURE 4–1: 489 LED Indicators
a) 489 Status LED Indicators
• 489 IN SERVICE: Indicates that control power is applied, all monitored input/
output and internal systems are OK, the 489 has been programmed, and is in
protection mode, not simulation mode. When in simulation or testing mode, the
LED indicator will flash.
• SETPOINT ACCESS: Indicates that the access jumper is installed and passcode
protection has been satisfied. Setpoints may be altered and stored.
• COMPUTER RS232: Flashes when there is any activity on the RS232
communications port. Remains on continuously if incoming data is valid.
• COMPUTER RS485 / AUXILIARY RS485: Flashes when there is any activity
on the computer/auxiliary RS485 communications port. These LEDs remain on
continuously if incoming data is valid and intended for the slave address
programmed in the relay.
• ALT. SETPOINTS: Flashes when the alternate setpoint group is being edited
and the primary setpoint group is active. Remains on continuously if the
alternate setpoint group is active. The alternate setpoint group feature is
enabled as one of the assignable digital inputs. The alternate setpoints group
can be selected by setting the S3 DIGITAL INPUTS ZV DUAL SETPOINTS ZV ACTIVATE
SETPOINT GROUP setpoint to “Group 2”.
• RESET POSSIBLE: A trip or latched alarm may be reset. Pressing the RESET key
clears the trip/alarm.
• MESSAGE: Under normal conditions, the default messages selected during
setpoint programming are displayed. If any alarm or trip condition is generated,
a diagnostic message overrides the displayed message and this indicator
flashes. If there is more than one condition present, MESSAGE T can be used to
scroll through the messages. Pressing any other key return to the normally
displayed messages. While viewing normally displayed messages, the Message
LED continues to flash if any diagnostic message is active. To return to the
diagnostic messages from the normally displayed messages, press the MENU key
until the following message is displayed:
Now, press the MESSAGE X key followed by the message T key to scroll through
the messages. Note that diagnostic messages for alarms disappear with the
condition while diagnostic messages for trips remain until cleared by a reset.
RS232 Program Port This port is intended for connection to a portable PC. Setpoint files may be created at any
location and downloaded through this port with the EnerVista 489 Setup software. Local
interrogation of setpoints and actual values is also possible. New firmware may be
downloaded to the 489 flash memory through this port. Upgrading the relay firmware
does not require a hardware EEPROM change.
Keypad a) Description
The 489 display messages are organized into main menus, pages, and sub-pages. There
are three main menus labeled Setpoints, Actual Values, and Target Messages.
Pressing the MENU key followed by the MESSAGE T key scrolls through the three main
menu headers, which appear in sequence as follows:
SETPOINTS [Z]
Pressing the MESSAGE X key or the ENTER key from these main menu pages will display the
Interfaces
corresponding menu page. Use the MESSAGE T and MESSAGE S keys to scroll through the
page headers.
When the display shows SETPOINTS, pressing the MESSAGE X key or the ENTER key will
display the page headers of programmable parameters (referred to as setpoints in the
manual). When the display shows ACTUAL VALUES, pressing the MESSAGE X key or the
ENTER key displays the page headers of measured parameters (referred to as actual
values in the manual). When the display shows TARGET MESSAGES, pressing the
MESSAGE X key or the ENTER key displays the page headers of event messages or alarm
conditions.
Each page is broken down further into logical sub-pages. The MESSAGE T and MESSAGE S
keys are used to navigate through the sub-pages. A summary of the setpoints and actual
values can be found in the chapters 5 and 6, respectively.
The ENTER key is dual purpose. It is used to enter the sub-pages and to store altered
setpoint values into memory to complete the change. The MESSAGE X key can also be
used to enter sub-pages but not to store altered setpoints.
The ESCAPE key is also dual purpose. It is used to exit the sub-pages and to cancel a
setpoint change. The MESSAGE W key can also be used to exit sub-pages and to cancel
setpoint changes.
The VALUE keys are used to scroll through the possible choices of an enumerated setpoint.
They also decrement and increment numerical setpoints. Numerical setpoints may also
be entered through the numeric keypad.
Pressing the HELP key displays context-sensitive information about setpoints such as the
range of values and the method of changing the setpoint. Help messages will
automatically scroll through all messages currently appropriate.
The RESET key resets any latched conditions that are not presently active. This includes
resetting latched output relays, latched Trip LEDs, breaker operation failure, and trip coil
failure.
The MESSAGE T and MESSAGE S keys scroll through any active conditions in the relay.
Diagnostic messages are displayed indicating the state of protection and monitoring
elements that are picked up, operating, or latched. When the Message LED is on, there
are messages to be viewed with the MENU key by selecting target messages as described
earlier.
2. Press the MESSAGE T key to view the INPUT NAME setpoint. The name of this user-
defined input will be changed in this example from the generic “Input A” to
something more descriptive.
3. If an application is to be using the relay as a station monitor, it is more informa-
tive to rename this input “Stn. Monitor”. Press the decimal [.] to enter the text
editing mode. The first character will appear underlined as follows:
INPUT NAME:
Input A
4. Press the VALUE keys until the character “S” is displayed in the first position. Now
press the decimal [.] key to store the character and advance the cursor to the
next position. Change the second character to a “t” in the same manner. Con-
tinue entering characters in this way until all characters of the text “Stn. Moni-
tor” are entered. Note that a space is selected like a character. If a character is
entered incorrectly, press the decimal [.] key repeatedly until the cursor returns
Interfaces
to the position of the error. Re-enter the character as required. Once complete,
press the ENTER key to remove the solid cursor and view the result. Once a char-
acter is entered, by pressing the ENTER key, it is automatically saved in Flash
Memory, as a new setpoint.
INPUT NAME:
Stn. Monitor
5. The 489 does not have '+' or '–' keys. Negative numbers may be entered in one
of two manners.
– Immediately pressing one of the VALUE keys causes the setpoint to scroll
through its range including any negative numbers.
– After entering at least one digit of a numeric setpoint value, pressing the
VALUE keys changes the sign of the value where applicable.
Setpoint Entry To store any setpoints, terminals C1 and C2 (access terminals) must be shorted (a
keyswitch may be used for security). There is also a setpoint passcode feature that
restricts access to setpoints. The passcode must be entered to allow the changing of
setpoint values. A passcode of “0” effectively turns off the passcode feature - in this case
only the access jumper is required for changing setpoints. If no key is pressed for 5
minutes, access to setpoint values will be restricted until the passcode is entered again.
To prevent setpoint access before the 5 minutes expires, the unit may be turned off and
back on, the access jumper may be removed, or the SETPOINT ACCESS setpoint may be
changed to “Restricted”. The passcode cannot be entered until terminals C1 and C2
(access terminals) are shorted. When setpoint access is allowed, the Setpoint Access LED
indicator on the front of the 489 will be lit.
Setpoint changes take effect immediately, even when generator is running. However,
changing setpoints while the generator is running is not recommended as any mistake
may cause a nuisance trip.
The following procedure may be used to access and alter setpoints. This specific example
refers to entering a valid passcode to allow access to setpoints if the passcode was “489”.
1. Press the MENU key to access the header of each menu, which will be displayed
in the following sequence:
SETPOINTS [Z]
2. Press the MENU key until the display shows the header of the setpoints menu,
then press the MESSAGE X or ENTER key to display the header for the first set-
points page. The set point pages are numbered, have an 'S' prefix for easy iden-
tification and have a name which gives a general idea of the settings available in
that page. Pressing the MESSAGE T or MESSAGE S keys will scroll through all the
available setpoint page headers. Setpoint page headers look as follows:
SETPOINTS [Z]
S1 489 SETUP
3. To enter a given setpoints page, press the MESSAGE X or ENTER key. Press the
MESSAGE T or MESSAGE S keys to scroll through sub-page headers until the
required message is reached. The end of a page is indicated by the message
END OF PAGE. The beginning of a page is indicated by the message TOP OF
PAGE.
4. Each page is broken further into subgroups. Press MESSAGE T or MESSAGE S to
cycle through subgroups until the desired subgroup appears on the screen.
Press the MESSAGE X or ENTER key to enter a subgroup.
PASSCODE [Z]
Interfaces
5. Each sub-group has one or more associated setpoint messages. Press the
MESSAGE T or MESSAGE S keys to scroll through setpoint messages until the
desired message appears.
ENTER PASSCODE
FOR ACCESS:
6. The majority of setpoints are changed by pressing the VALUE keys until the
desired value appears, and then pressing ENTER. Numeric setpoints may also be
entered through the numeric keys (including decimals). If the entered setpoint
is out of range, the original setpoint value reappears. If the entered setpoint is
out of step, an adjusted value will be stored (e.g. 101 for a setpoint that steps
95, 100, 105 is stored as 100). If a mistake is made entering the new value,
pressing ESCAPE returns the setpoint to its original value. Text editing is a special
case described in detail in Entering Alphanumeric Text on page 4–3. Each time a
new setpoint is successfully stored, a message will flash on the display stating
NEW SETPOINT HAS BEEN STORED.
7. Press the 4, 8, 9 keys, then press ENTER. The following flash message is dis-
played:
NEW SETPOINT
HAS BEEN STORED
Diagnostic Messages Diagnostic messages are automatically displayed for any active conditions in the relay
such as trips, alarms, or asserted logic inputs. These messages provide a summary of the
present state of the relay. The Message LED flashes when there are diagnostic messages
available; press the MENU key until the relay displays TARGET MESSAGES, then press the
MESSAGE X key, followed by the MESSAGE T key, to scroll through the messages. For
additional information and a complete list of diagnostic messages, refer to Diagnostic
Messages on page 6–25.
Self-Test Warnings The 489 relay performs self test diagnostics at initialization (after power up), and
continuously as a background task to ensure every testable unit of the hardware and
software is functioning correctly. There are two types of self-test warnings indicating
either a minor or major problem. Minor problems indicate a problem with the relay that
does not compromise protection. Major problems indicate a very serious relay problem
which comprises all aspects of relay operation.
Upon detection of either a minor or a major problem the relay will:
• De-energize the self-test warning relay
• Light the self-test warning LED
• Flash a diagnostic message periodically on the display screen
The 489 self-test warnings are shown below.
failure.
Self-Test Warning 3 Major This warning is caused by a failure of the
Replace Immediately analog to digital converter. The integrity of
system input measurements is affected by this
failure.
Self-Test Warning 5 Major This warning is caused by out of range reading
Replace Immediately of self test RTD 13. The integrity of system
input measurements is affected by this failure.
Self-Test Warning 6 Major This warning is caused by out of range reading
Replace Immediately of self test RTD 14. The integrity of system
input measurements is affected by this failure.
Self-Test Warning 7 Major This warning is caused by out of range reading
Replace Immediately of self test RTD15. The integrity of system
input measurements is affected by this failure.
Self-Test Warning 8 Major This warning is caused by out of range reading
Replace Immediately of self test RTD16. The integrity of system
input measurements is affected by this failure.
Clock Not Set Minor Occurs if the clock has not been set.
Program Date/Time
Unit Temp. Exceeded Minor Caused by the detection of unacceptably low
Service/CheckAmbient (less than –40°C) or high (greater than 85°C)
temperatures detected inside the unit.
Unit Not Calibrated Minor This warning occurs when the relay has not
Replace Immediately been factory calibrated.
Relay Not Configured Minor This warning occurs when the 489 CT Primary
Consult User Manual or FLA is set to "None".
Service Required Minor This warning is caused by a failure of the Real
Schedule Maintenance Time Clock circuit. The ability of the relay to
maintain the current date and time is lost.
Flash Messages Flash messages are warning, error, or general information messages displayed in
response to certain key presses. The length of time these messages remain displayed can
be programmed in S1 RELAY SETUP ZV PREFERENCES ZV DEFAULT MESSAGE CYCLE TIME.
The factory default flash message time is 4 seconds. For additional information and a
complete list of flash messages, refer to Flash Messages on page 6–26.
Interfaces
• Perform waveform capture and log data
• Plot, print, and view trending graphs of selected actual values
• Download and playback waveforms
• Get help on any topic
Hardware Communications from the EnerVista 489 Setup to the 489 can be accomplished three
ways: RS232, RS485, and Ethernet (requires the MultiNET adapter) communications. The
following figures below illustrate typical connections for RS232 and RS485
communications. For additional details on Ethernet communications, please see the
MultiNET manual (GE Publication number GEK-106498).
Installing the EnerVista The following minimum requirements must be met for the EnerVista 489 Setup software
489 Setup Software to operate on your computer.
• Pentium class or higher processor (Pentium II 400 MHz or better recommended)
• Microsoft Windows 95, 98, 98SE, ME, NT 4.0 (SP4 or higher), 2000, XP
• Internet Explorer version 4.0 or higher (required libraries)
• 128 MB of RAM (256 MB recommended)
• Minimum of 200 MB hard disk space
A list of qualified modems for serial communications is shown below:
• US Robotics external 56K Faxmodem 5686
• US Robotics external Sportster 56K X2
• PCTEL 2304WT V.92 MDC internal modem
After ensuring these minimum requirements, use the following procedure to install the
EnerVista 489 Setup software from the enclosed GE EnerVista CD.
1. Insert the GE EnerVista CD into your CD-ROM drive.
2. Click the Install Now button and follow the installation instructions to install
the no-charge EnerVista software on the local PC.
3. When installation is complete, start the EnerVista Launchpad application.
5. In the EnerVista Launch Pad window, click the Add Product button and select
the “489 Generator Management Relay” from the Install Software window as
shown below. Select the “Web” option to ensure the most recent software
release, or select “CD” if you do not have a web connection, then click the Add
Now button to list software items for the 489.
Interfaces
6. EnerVista Launchpad will obtain the latest installation software from the Web or
CD and automatically start the installation process. A status window with a
progress bar will be shown during the downloading process.
Interfaces
7. Select the complete path, including the new directory name, where the EnerV-
ista 489 Setup software will be installed.
8. Click on Next to begin the installation. The files will be installed in the directory
indicated and the installation program will automatically create icons and add
EnerVista 489 Setup software to the Windows start menu.
9. Click Finish to end the installation. The 489 device will be added to the list of
installed IEDs in the EnerVista Launchpad window, as shown below.
Interfaces
dow.
5. Click the Add Device button to define the new device.
6. Enter the desired name in the Device Name field and a description (optional)
of the site.
7. Select “Serial” from the Interface drop-down list. This will display a number of
interface parameters that must be entered for proper RS232 functionality.
– Enter the slave address and COM port values (from the S1 489 SETUP ZV
COMMUNICATIONS menu) in the Slave Address and COM Port fields.
– Enter the physical communications parameters (baud rate and parity set-
points) in their respective fields. Note that when communicating to the
relay from the front port, the default communications settings are a baud
rate of 9600, with slave address of 1, no parity, 8 bits, and 1 stop bit.
These values cannot be changed.
8. Click the Read Order Code button to connect to the 489 device and upload the
order code. If a communications error occurs, ensure that the 489 serial com-
munications values entered in the previous step correspond to the relay setting
values.
9. Click OK when the relay order code has been received. The new device will be
added to the Site List window (or Online window) located in the top left corner
of the main EnerVista 489 Setup window.
The 489 Site Device has now been configured for serial communications. Proceed to
Connecting to the Relay on page 4–13 to begin communications.
Using the Quick The Quick Connect button can be used to establish a fast connection through the front
Connect Feature panel RS232 port of a 489 relay. The following window will appear when the Quick
Connect button is pressed:
Interfaces
As indicated by the window, the Quick Connect feature quickly connects the EnerVista
489 Setup software to a 489 front port with the following settings: 9600 baud, no parity,
8 bits, 1 stop bit. Select the PC communications port connected to the relay and press the
Connect button.
The EnerVista 489 Setup software will display a window indicating the status of
communications with the relay. When connected, a new Site called “Quick Connect” will
appear in the Site List window. The properties of this new site cannot be changed.
The 489 Site Device has now been configured via the Quick Connect feature for serial
communications. Proceed to Connecting to the Relay on page 4–13 to begin
communications.
Configuring Ethernet Before starting, verify that the Ethernet cable is properly connected to the RJ-45 Ethernet
Communications port.
1. Install and start the latest version of the EnerVista 489 Setup software
(available from the GE EnerVista CD). See the previous section for the
installation procedure.
2. Click on the Device Setup button to open the Device Setup window and click
the Add Site button to define a new site.
3. Enter the desired site name in the Site Name field. If desired, a short
description of site can also be entered along with the display order of devices
defined for the site. In this example, we will use “Pumping Station 2” as the site
name. Click the OK button when complete.
4. The new site will appear in the upper-left list.
5. Click the Add Device button to define the new device.
6. Enter the desired name in the Device Name field and a description (optional).
7. Select “Ethernet” from the Interface drop-down list. This will display a number
of interface parameters that must be entered for proper Ethernet functionality.
Interfaces
• Enter the IP address assigned to the relay.
• Enter the slave address and Modbus port values (from the S1 489 SETUP ZV
COMMUNICATIONS menu) in the Slave Address and Modbus Port fields.
8. Click the Read Order Code button to connect to the 489 device and upload the
order code. If an communications error occurs, ensure that the 489 Ethernet
communications values entered in the previous step correspond to the relay
setting values.
9. Click OK when the relay order code has been received. The new device will be
added to the Site List window (or Online window) located in the top left corner
of the main EnerVista 489 Setup window.
The 489 Site Device has now been configured for Ethernet communications. Proceed to
the following section to begin communications.
Connecting to the Now that the communications parameters have been properly configured, the user can
Relay easily connect to the relay.
1. Expand the Site list by double clicking on the site name or clicking on the «+»
box to list the available devices for the given site (for example, in the “Pumping
Station 1” site shown below).
2. Desired device trees can be expanded by clicking the «+» box. The following list
of headers is shown for each device:
• Device Definitions
• Settings
• Actual Values
• Commands
• Communications
3. Expand the Setpoints > Protection > Current Elements list item and select
the Phase Overcurrent tab to open the Phase Overrcurrent settings window as
shown below:
Entering Setpoints The System Setup page will be used as an example to illustrate the entering of setpoints.
In this example, we will be changing the current sensing setpoints.
1. Establish communications with the relay.
2. Select the Setpoint > System Setup menu item. This can be selected from
the device setpoint tree or the main window menu bar.
3. Select the PHASE CT PRIMARY setpoint by clicking anywhere in the parameter box.
This will display three arrows: two to increment/decrement the value and
another to launch the numerical calculator.
Interfaces
4. Clicking the arrow at the end of the box displays a numerical keypad interface
that allows the user to enter a value within the setpoint range displayed near
the top of the keypad:
Click Accept to exit from the keypad and keep the new value. Click on Cancel
to exit from the keypad and retain the old value.
5. For setpoints requiring non-numerical pre-set values (e.g. VT CONNECTION TYPE
below, in the Voltage Sensing window), clicking anywhere within the setpoint
value box displays a drop-down selection menu arrow. Click on the arrow to
select the desired setpoint.
• In off-line mode (relay disconnected) to create or edit relay settings files for
later download to communicating relays.
• Directly modifying relay settings while connected to a communicating relay,
then saving the settings when complete.
• Creating/editing settings files while connected to a communicating relay, then
saving them to the relay when complete.
Settings files are organized on the basis of file names assigned by the user. A settings file
contains data pertaining to the following types of relay settings:
• Device Definition
• Product Setup
• System Setup
• Digital Inputs
• Output Relays
• Voltage Elements
• Power Elements
• RTD Temperature
• Thermal Model
• Monitoring Functions
• Analog Inputs and Outputs
• Relay Testing
• User Memory Map Setting Tool
Factory default values are supplied and can be restored after any changes.
The EnerVista 489 Setup display relay setpoints with the same hierarchy as the front
panel display. For specific details on setpoints, refer to Chapter 5.
1. Ensure that the site and corresponding device(s) have been properly defined
and configured as shown in Connecting EnerVista 489 Setup to the Relay on
page 4–11.
2. Select the desired device from the site list.
3. Select the File > Read Settings from Device menu item to obtain settings
information from the device.
4. After a few seconds of data retrieval, the software will request the name and
destination path of the setpoint file. The corresponding file extension will be
automatically assigned. Press Save to complete the process. A new entry will
be added to the tree, in the File pane, showing path and file name for the set-
point file.
Interfaces
2. The Open dialog box will appear, prompting for a previously saved setpoint file.
As for any other Windows® application, browse for the file to add then click
Open. The new file and complete path will be added to the file list.
3. For future reference, enter some useful information in the Description box to
facilitate the identification of the device and the purpose of the file.
4. To select a file name and path for the new file, click the button beside the Enter
File Name box.
5. Select the file name and path to store the file, or select any displayed file name
to update an existing file. All 489 setpoint files should have the extension ‘489’
(for example, ‘motor1.489’).
6. Click Save and OK to complete the process. Once this step is completed, the
new file, with a complete path, will be added to the EnerVista 489 Setup soft-
ware environment.
3. Load the setpoint file to be upgraded into the EnerVista 489 Setup environment
as described in Adding Setpoints Files to the Environment on page 4–17.
Interfaces
Enter any special comments Select the desired setpoint version
about the setpoint file here. from this menu. The 3.0x indicates
versions 3.00, 3.01, 3.02, etc.
6. When complete, click Convert to convert the setpoint file to the desired revision.
A dialog box will request confirmation. See Loading Setpoints from a File on
page 4–20 for instructions on loading this setpoint file into the 489.
4. The process for File > Print Preview Settings is identical to the steps above.
Setpoints lists can be printed in the same manner by right clicking on the desired file (in
the file list) or device (in the device list) and selecting the Print Device Information or
Print Settings File options.
A complete list of actual values can also be printed from a connected device with the
following procedure:
1. Establish communications with the desired 489 device.
2. From the main window, select the File > Print Settings menu item.
3. The Print/Export Options dialog box will appear. Select Actual Values in the
upper section and select either Include All Features (for a complete list) or
Include Only Enabled Features (for a list of only those features which are
currently used) in the filtering section and click OK.
Actual values can be printed in the same manner by right clicking on the desired device
(in the device list) and selecting the Print Device Information option.
setpoints file, it must first be added to the EnerVista 489 Setup environment as described
in Adding Setpoints Files to the Environment on page 4–17.
1. Select the previously saved setpoints file from the File pane of the EnerVista
489 Setup software main window.
2. Select the File > Properties menu item and verify that the corresponding file
is fully compatible with the hardware and firmware version of the target relay. If
the versions are not identical, see Upgrading Setpoint Files to a New Revision on
page 4–18 for details on changing the setpoints file version.
3. Right-click on the selected file and select the Write Settings to Device item.
4. The software will prompt for a target device. Select the desired device and click
Send.
6. If there are no incompatibilities between the target device and the Setpoints
file, the data will be transferred to the relay. An indication of the percentage
completed will be shown in the bottom of the main menu.
Saving Setpoints To A Before upgrading firmware, it is very important to save the current 489 settings to a file
File on your PC. After the firmware has been upgraded, it will be necessary to load this file
back into the 489.
Refer to Downloading and Saving Setpoints Files on page 4–16 for details on saving relay
setpoints to a file.
Loading New Firmware Loading new firmware into the 489 flash memory is accomplished as follows:
Interfaces
1. Connect the relay to the local PC and save the setpoints to a file as shown in
Downloading and Saving Setpoints Files on page 4–16.
2. Select the Communications > Update Firmware menu item.
3. The following warning message will appear. Select Yes to proceed or No to can-
cel the process. Do not proceed unless you have saved the current set-
points.
32 J 300 A8 . 000
Modification Number (000 = none)
GE Multilin use only
Firmware version
Required 489 hardware revision
Product code (32 = 489)
FIGURE 4–5: Firmware File Format
6. The EnerVista 489 Setup software automatically lists all filenames beginning
with ‘32’. Select the appropriate file and click OK to continue.
7. The software will prompt with another Upload Firmware Warning window. This
will be the final chance to cancel the firmware upgrade before the flash memory
is erased. Click Yes to continue or No to cancel the upgrade.
8. The EnerVista 489 Setup software now prepares the 489 to receive the new
firmware file. The 489 will display a message indicating that it is in Upload
Mode. While the file is being loaded into the 489, a status box appears showing
how much of the new firmware file has been transferred and how much is
remaining, as well as the upgrade status. The entire transfer process takes
approximately five minutes.
9. The EnerVista 489 Setup software will notify the user when the 489 has finished
loading the file. Carefully read any displayed messages and click OK to return
the main screen.
Cycling power to the relay is recommended after a firmware upgrade.
After successfully updating the 489 firmware, the relay will not be in service and will
Interfaces
NOTE
require setpoint programming. To communicate with the relay, the following settings will
have to be manually programmed.
MODBUS COMMUNICATION ADDRESS
BAUD RATE
PARITY (if applicable)
When communications is established, the saved setpoints must be reloaded back into the
relay. See Loading Setpoints from a File on page 4–20 for details.
Modbus addresses assigned to firmware modules, features, settings, and corresponding
data items (i.e. default values, min/max values, data type, and item size) may change
slightly from version to version of firmware.
The addresses are rearranged when new features are added or existing features are
enhanced or modified. The EEPROM DATA ERROR message displayed after upgrading/
downgrading the firmware is a resettable, self-test message intended to inform users that
the Modbus addresses have changed with the upgraded firmware. This message does not
signal any problems when appearing after firmware upgrades.
Waveform Capture The EnerVista 489 Setup software can be used to capture waveforms (or view trace
(Trace Memory) memory) from the 489 relay at the instance of a trip. A maximum of 128 cycles can be
captured and the trigger point can be adjusted to anywhere within the set cycles. A
maximum of 16 waveforms can be buffered (stored) with the buffer/cycle trade-off.
The following waveforms can be captured:
• Phase A, B, and C currents (Ia, Ib, and Ic)
• Neutral end A, B, and C currents (Ineutral_a, Ineutral_b, and Ineutral_c)
• Ground currents (Ig)
• Phase A-N, B-N, and C-N voltages (Va, Vb, and Vc)
Interfaces
1. With EnerVista 489 Setup running and communications established, select the
Actual > Waveform Capture menu item to open the waveform capture setup
window:
3. To view the captured waveforms, click the Launch Viewer button. A detailed
Waveform Capture window will appear as shown below:
Preference button
Interfaces
Change the Color of each graph as desired, and select other options as
required, by checking the appropriate boxes. Click OK to store these graph
attributes, and to close the window.
8. The Waveform Capture window will reappear with the selected graph attributes
available for use.
Phasors The EnerVista 489 Setup software can be used to view the phasor diagram of three-phase
currents and voltages. The phasors are for: Phase Voltages Va, Vb, and Vc; Phase
Currents Ia, Ib, and Ic.
1. With the EnerVista 489 Setup software running and communications estab-
lished, open the Actual Values > Metering Data window, then click on the
Phasors tab.
2. The EnerVista 489 Setup software will display the following window:
4. The 489 Generator Management Relay was designed to display lagging angles.
Therefore, if a system condition would cause the current to lead the voltage by
45°, the 489 relay will display such angle as 315° Lag instead of 45° Lead.
When the currents and voltages measured by the relay are zero, the angles
displayed by the relay and those shown by the EnerVista 489 Setup software are
WARNING not fixed values.
Trending (Data Logger) The trending or data logger feature is used to sample and record up to eight actual values
at an interval defined by the user. Several parameters can be trended and graphed at
sampling periods ranging from 1 second up to 1 hour. The parameters which can be
trended by the EnerVista 489 Setup software are:
• Currents/Voltages:
Phase Currents A, B, and C
Generator Load
Negative-Sequence Current
Ground Current and Neutral Current
Differential Currents A, B, and C
System Frequency
Voltages Vab, Vbc, Vca Van, Vbn & Vcn
• Power:
Power Factor
Real (kW) Reactive (kvar), and Apparent (kVA) Power
Positive Watthours
Positive and Negative Varhours
• Temperature:
Hottest Stator RTD
Thermal Capacity Used
RTDs 1 through 12
• Demand:
Current
Peak Current
Reactive Power
Peak Reactive Power
Apparent Power
Peak Apparent Power
• Others:
Analog Inputs 1, 2, 3, and 4
Tachometer
1. With EnerVista 489 Setup running and communications established, select the
Actual Values > Trending menu item to open the trending window. The fol-
lowing window will appear.
Interfaces
2. To prepare for new trending, select Stop to stop the data logger and Reset to
clear the screen.
3. Select the graphs to be displayed through the pull-down menu beside each
channel description.
4. Select the Sample Rate through the pull-down menu.
5. If you want to save the information captured by trending, check the box besides
Log Samples to File. The following dialog box will appear requesting for file
name and path. The file is saved as 'csv' (comma delimited values) file, which
can be viewed and manipulated with compatible third-party software. Ensure
that the sample rate not less than 5 seconds. Otherwise, some data may not get
written to the file.
6. To limit the size of the saved file, enter a number in the Limit File Capacity To
box. The minimum number of samples is 1000. At a sampling rate of 5 seconds
(or 1 sample every 5 seconds), the file will contain data collected during the
past 5000 seconds. The EnerVista 489 Setup software will automatically esti-
mate the size of the trending file.
7. Press “Run” to start the data logger. If the Log Samples to File item is
selected, the EnerVista 489 Setup software will begin collecting data at the
selected sampling rate and will display it on the screen. The data log will con-
tinue until the Stop button is pressed or until the selected number of samples is
reached, whichever occurs first.
8. During the process of data logging, the trending screen appears as shown
below.
SAVE DATA TO FILE MODE SELECT BUTTONS
Select to save the Select to view Cursor 1, Zoom In enlarges the graph
information to a CSV Cursor 2, or the Delta Zoom Out shrinks the graph
file on the PC (difference) values for Reset clears the screen
the graph Run/Stop starts and stops
the data logger
Interfaces
Event Recorder The 489 event recorder can be viewed through the EnerVista 489 Setup software. The
event recorder stores generator and system information each time an event occurs (e.g.
breaker failure). A maximum of 256 events can be stored. Each event is assigned an
event number, from E001 to E256. When the E256 is reached, E001 is assigned to the
next event. Refer to Event Recorder on page 6–23 for additional information on the event
recorder.
Use the following procedure to view the event recorder with EnerVista 489 Setup:
1. With EnerVista 489 Setup running and communications established, select the
Actual > A4 Event Recorder item from the main menu. This displays the
Event Recorder window indicating the list of recorded events, with the most cur-
rent event displayed first.
EVENT LISTING EVENT SELECTION EVENT NUMBER CLEAR EVENTS
Lists the last 256 Select an event row to view The event data Click the Clear
events with the most event data information, information is related Events button to
recent displayed at which will be displayed in to the selected event, clear the event list
top of list. the window to the right. as shown. from memory.
Interfaces
DEVICE ID EVENT DATA SAVE EVENTS
The events shown System information as Click the Save Events
here correspond to measured by the relay at button to save the event
the device shown. the instant of the event record to the PC as a
occurrence. CSV file.
FIGURE 4–8: Event Recorder Window (shown unconnected)
2. To view detailed information for a given event and the system information at the
moment of the event occurrence, change the event number on the Select
Event box.
Modbus User Map The EnerVista 489 Setup software provides a means to program the 489 User Map
(Modbus addresses 0180h to 01F7h). Refer to GE Publication GEK-106491: 489
Communications Guide for additional information on the User Map.
1. Select a connected device in EnerVista 489 Setup.
2. Select the Setpoint > User Map menu item to open the following window.
This window allows the desired addresses to be written to User Map locations.
The User Map values that correspond to these addresses are then displayed.
Viewing Actual Values You can view real-time relay data such as input/output status and measured parameters.
From the main window menu bar, selecting Actual Values opens a window with tabs, each
tab containing data in accordance to the following list:
1. Generator and System Status:
– Generator status either stopped, starting, or running. It includes values
such as generator load, thermal capacity used, generator speed, and
instantaneous values of power system quantities.
– The status of digital inputs.
– Last trip information, including values such as cause of last trip, time and
date of trip, generator speed and load at the time of trip, pre-trip tempera-
ture measurements, pre-trip analog inputs values, and pre-trip instanta-
neous values of power system quantities.
– Active alarms.
– Relay date and time.
– Present blocking conditions.
– General system status indication including the status of output relays,
active pickup, alarm and trip conditions.
2. Metering Data:
– Instantaneous current measurements including phase, differential, unbal-
ance, ground, average, generator load, and differential currents.
– RTD Temperatures including hottest RTDs.
– Instantaneous phase to phase and phase to ground voltages (depending on
the VT connections), average voltage, and system frequency.
– Generator Speed
– Power Quantities including Apparent, Real and Reactive Power.
– Current and power demand including peak values.
– Analog inputs
– Vector information.
Interfaces
corresponding device in the site list and highlights the current location in the hierarchy.
For complete details on actual values, refer to Chapter 6.
To view a separate window for each group of actual values, select the desired item from
the tree, and double click with the left mouse button. Each group will be opened on a
separate tab. The windows can be re-arranged to maximize data viewing as shown in the
following figure (showing actual current, voltage, and generator status values tiled in the
same window):
Interfaces
FIGURE 4–11: Device Setup Screen (Example)
9. Click the Read Order Code button to connect to the 489 device and upload the
order code. If an communications error occurs, ensure that communications
values entered in the previous step correspond to the relay setting values.
10. Click OK when complete.
11. From the EnerVista main window, select the IED Dashboard item to open the
Plug and Play IED dashboard. An icon for the 489 will be shown.
5 Setpoints
Overview
Setpoint Message Map The 489 has a considerable number of programmable setpoints which makes it
extremely flexible. The setpoints have been grouped into a number of pages and
sub-pages as shown below. Each page of setpoints (e.g. S2 SYSTEM SETUP) has a
section which describes in detail all the setpoints found on that page.
PASSCODE [Z]
See page 5–7.
Setpoints
SETPOINTS [Z]
MESSAGE PREFERENCES [Z] See page 5–8.
MESSAGE COMMUNICATIONS [Z] See page 5–9.
REAL
MESSAGE TIME [Z] See page 5–10.
MESSAGE DEFAULT [Z] See page 5–11.
MESSAGE MESSAGE [Z] See page 5–12.
CLEAR
MESSAGE DATA [Z] See page 5–13.
END OF PAGE
MESSAGE
SETPOINTS [Z] CURRENT [Z] See page 5–14.
MESSAGE VOLTAGE [Z] See page 5–14.
MESSAGE GENERATOR [Z] See page 5–15.
MESSAGE SERIAL [Z] See page 5–15.
END OF PAGE
MESSAGE
SETPOINTS [Z] BREAKER [Z] See page 5–16.
MESSAGE GENERAL [Z] See page 5–17.
MESSAGE GENERAL [Z] See page 5–17.
MESSAGE GENERAL [Z] See page 5–17.
REMOTE
MESSAGE RESET [Z] See page 5–18.
TEST
MESSAGE INPUT [Z] See page 5–18.
THERMAL
MESSAGE RESET [Z] See page 5–18.
Setpoints
MESSAGE DUAL [Z] See page 5–18.
MESSAGE SEQUENTIAL [Z] See page 5–19.
FIELD-
MESSAGE BREAKER [Z] See page 5–20.
MESSAGE TACHOMETER [Z] See page 5–20.
MESSAGE WAVEFORM [Z] See page 5–21.
MESSAGE GROUND [Z] See page 5–21.
END OF PAGE
MESSAGE
SETPOINTS [Z] RELAY [Z] See page 5–22.
END OF PAGE
MESSAGE
1 OFFLINE [Z]
MESSAGE See page 5–26.
OVERCURRENT
1 INADVERTENT [Z]
MESSAGE See page 5–26.
ENERGIZATION
1 PHASE [Z]
MESSAGE See page 5–27.
OVERCURRENT
1 NEGATIVE [Z]
MESSAGE See page 5–28.
SEQUENCE
1 GROUND [Z]
MESSAGE See page 5–30.
OVERCURRENT
1 PHASE [Z]
MESSAGE See page 5–31.
DIFFERENTIAL
1 GROUND [Z]
MESSAGE See page 5–32.
DIRECTIONAL
1 HIGH-SET [Z]
MESSAGE See page 5–33.
PHASE OVERCURRENT
END OF PAGE
MESSAGE
1 OVERVOLTAGE [Z]
Setpoints
MESSAGE See page 5–35.
1 VOLTS/HERTZ [Z]
MESSAGE See page 5–36.
1 PHASE [Z]
MESSAGE See page 5–39.
REVERSAL
1 UNDERFREQUENCY [Z]
MESSAGE See page 5–39.
1 OVERFREQUENCY [Z]
MESSAGE See page 5–40.
1 LOSS OF [Z]
MESSAGE See page 5–44.
EXCITATION
1 DISTANCE [Z]
MESSAGE See page 5–45.
ELEMENT
END OF PAGE
MESSAGE
1 REVERSE [Z]
MESSAGE See page 5–50.
POWER
END OF PAGE
MESSAGE
1 RTD #1 [Z]
MESSAGE See page 5–52.
1 RTD #2 [Z]
MESSAGE See page 5–52.
1 RTD #3 [Z]
MESSAGE See page 5–52.
1 RTD [Z]
MESSAGE See page 5–55.
SHORT/LOW TEMP
END OF PAGE
MESSAGE
Setpoints
1 THERMAL [Z]
MESSAGE See page 5–71.
ELEMENTS
END OF PAGE
MESSAGE
SETPOINTS [Z] TRIP [Z] See page 5–72.
MESSAGE BREAKER [Z] See page 5–72.
TRIP COIL
MESSAGE [Z] See page 5–72.
VT FUSE
MESSAGE [Z] See page 5–73.
MESSAGE CURRENT [Z] See page 5–75.
MW
MESSAGE DEMAND [Z] See page 5–75.
Mvar
MESSAGE DEMAND [Z] See page 5–75.
MVA
MESSAGE DEMAND [Z] See page 5–75.
MESSAGE PULSE [Z] See page 5–76.
MESSAGE RUNNING [Z] See page 5–77.
END OF PAGE
MESSAGE
SETPOINTS [Z] ANALOG [Z] See page 5–78.
MESSAGE ANALOG [Z] See page 5–78.
MESSAGE ANALOG [Z] See page 5–78.
MESSAGE ANALOG [Z] See page 5–78.
MESSAGE ANALOG [Z] See page 5–79.
Setpoints
MESSAGE ANALOG [Z] See page 5–79.
MESSAGE ANALOG [Z] See page 5–79.
MESSAGE ANALOG [Z] See page 5–79.
END OF PAGE
MESSAGE
SETPOINTS [Z] SIMULATION [Z] See page 5–81.
PRE-
MESSAGE FAULT [Z] See page 5–82.
MESSAGE FAULT [Z] See page 5–83.
MESSAGE TEST [Z] See page 5–84.
MESSAGE TEST [Z] See page 5–84.
MESSAGE COMMUNICATION [Z] See page 5–85.
MESSAGE FACTORY [Z] See page 5–85.
END OF PAGE
MESSAGE
Trips / Alarms/ Control The 489 Generator Management Relay has three basic function categories: TRIPS,
Features ALARMS, and CONTROL.
a) Trips
A 489 trip feature may be assigned to any combination of the four output relays:
1 Trip, 2 Auxiliary, 3 Auxiliary, and 4 Auxiliary. If a Trip becomes active, the
appropriate LED (indicator) on the 489 faceplate illuminates to indicate which
output relay has operated. Each trip feature may be programmed as latched or
unlatched. Once a latched trip feature becomes active, the RESET key must be
pressed to reset that trip. If the condition that caused the trip is still present (for
example, hot RTD) the trip relay(s) will not reset until the condition disappears. On
the other hand, if an unlatched trip feature becomes active, that trip resets itself
(and associated output relay(s)) after the condition that caused the trip ceases and
the Breaker Status input indicates that the breaker is open. If there is a lockout
time, the trip relay(s) will not reset until the lockout time has expired. Immediately
prior to issuing a trip, the 489 takes a snapshot of generator parameters and stores
them as pre-trip values, allowing for troubleshooting after the trip. The cause of last
trip message is updated with the current trip and the 489 display defaults to that
message. All trip features are automatically logged and date and time stamped as
they occur. In addition, all trips are counted and logged as statistics such that any
long term trends may be identified.
Note that a lockout time will occur due to overload trip (see Model Setup on page 5–
57 for additional details).
b) Alarms
Setpoints
A 489 alarm feature may be assigned to operate any combination of four output
relays: 2 Auxiliary, 3 Auxiliary, 4 Auxiliary, and 5 Alarm. When an alarm becomes
active, the appropriate LED (indicator) on the 489 faceplate will illuminate when an
output relay(s) has operated. Each alarm feature may be programmed as latched or
unlatched. Once a latched alarm feature becomes active, the reset key must be
pressed to reset that alarm. If the condition that has caused the alarm is still
present (for example, hot RTD) the Alarm relay(s) will not reset until the condition is
no longer present. If on the other hand, an unlatched alarm feature becomes active,
that alarm will reset itself (and associated output relay(s)) as soon as the condition
that caused the alarm ceases. As soon as an alarm occurs, the alarms messages are
updated to reflect the alarm and the 489 display defaults to that message. Since it
may not be desirable to log all alarms as events, each alarm feature may be
programmed to log as an event or not. If an alarm is programmed to log as an
event, when it becomes active, it is automatically logged as a date and time
stamped event.
c) Control
A 489 control feature may be assigned to operate any combination of five output
relays: 1 Trip, 2 Auxiliary, 3 Auxiliary, 4 Auxiliary, and 5 Alarm. The combination of
relays available for each function is determined by the suitability of each relay for
that particular function. The appropriate LED (indicator) on the 489 faceplate will
illuminate when an output relay(s) has been operated by a control function. Since it
may not be desirable to log all control function as events, each control feature may
be programmed to log as an event or not. If a control feature is programmed to log
as an event, each control relay event is automatically logged with a date and time
stamp.
Relay Assignment There are six output relays. Five of the relays are always non-failsafe, the other
Practices (Service) is failsafe and dedicated to annunciate internal 489 faults (these faults
include setpoint corruption, failed hardware components, loss of control power,
etc.). The five remaining relays may be programmed for different types of features
depending on what is required. One of the relays, 1 Trip, is intended to be used as a
trip relay wired to the unit trip breaker. Another relay, 5 Alarm, is intended to be
used as the main alarm relay. The three remaining relays, 2 Auxiliary, 3 Auxiliary,
and 4 Auxiliary, are intended for special requirements.
When assigning features to relays 2, 3, and 4, it is a good idea to decide early on
what is required since features that may be assigned may conflict. For example, if
relay 2 is to be dedicated as a relay for sequential tripping, it cannot also be used to
annunciate a specific alarm condition.
In order to ensure that conflicts in relay assignments do not occur, several
precautions have been taken. All trips default to the 1 Trip output relay and all
alarms default to the 5 Alarm relay. It is recommended that relay assignments be
reviewed once all the setpoints have been programmed.
Dual Setpoints The 489 has dual settings for the current, voltage, power, RTD, and thermal model
protection elements (setpoints pages S5 to S9). These setpoints are organized in
two groups: the main group (Group 1) and the alternate group (Group 2). Only one
group of settings is active in the protection scheme at a time. The active group can
be selected using the ACTIVATE SETPOINT GROUP setpoint or an assigned digital input
in the S3 Digital Inputs setpoints page. The LED indicator on the faceplate of the
489 will indicate when the alternate setpoints are active in the protection scheme.
Independently, the setpoints in either group can be viewed and/or edited using the
EDIT SETPOINT GROUP setpoint. Headers for each setpoint message subgroup that has
dual settings will be denoted by a superscript number indicating which setpoint
group is being viewed or edited. Also, when a setpoint that has dual settings is
stored, the flash message that appears will indicate which setpoint group setting
has been changed.
If only one setting group is required, edit and activate only Group 1 (that is, do not
Setpoints
assign a digital input to Dual Setpoints, and do not alter the ACTIVATE SETPOINT
GROUP setpoint or EDIT SETPOINT GROUP setpoint in S3 DIGITAL INPUTS).
Commissioning Tables for recording of 489 programmed setpoints are available as a Microsoft Word
document from the GE Multilin website at http://www.GEmultilin.com. See the
Support Documents section of the 489 Generator Management Relay page for the
latest version. This document is also available in print from the GE Multilin literature
department (request publication number GET-8445).
S1 489 Setup
Passcode PATH: SETPOINTS Z S1 489 SETUP Z PASSCODE
A passcode access security feature is provided with the 489. The passcode is
defaulted to “0” (without the quotes) at the time of shipping. Passcode protection is
ignored when the passcode is “0”. In this case, the setpoint access jumper is the
only protection when programming setpoints from the front panel keypad and
setpoints may be altered using the RS232 and RS485 serial ports without access
protection. If however, the passcode is changed to a non-zero value, passcode
protection is enabled. The access jumper must be installed and the passcode must
be entered, to program setpoints from the front panel keypad. The passcode must
also be entered individually from each serial communications port to gain setpoint
programming access from that port.
The ENTER PASSCODE FOR ACCESS setpoint is seen only if the passcode is not 0 and
SETPOINT ACCESS is “Restricted”. The SETPOINT ACCESS and CHANGE PASSWORD
setpoints are seen only if the passcode is 0 and the SETPOINT ACCESS is “Permitted”.
To enable passcode protection on a new relay, follow the procedure below:
1. Press ENTER then MESSAGE DOWN until CHANGE PASSCODE message is displayed.
2. Select “Yes” and follow directions to enter a new passcode 1 to 8 digits in
length.
3. Once a new passcode (other than “0”) is programmed, it must be entered to
gain setpoint access whenever setpoint access is restricted. Assuming that a
non-zero passcode has been programmed and setpoint access is restricted,
then selecting the passcode subgroup causes the ENTER PASSCODE AGAIN
message to appear.
4. Enter the correct passcode. A flash message will advise if the code is incorrect
and allow a retry. If it is correct and the setpoint access jumper is installed, the
SETPOINT ACCESS: Permitted message appears.
5. Setpoints can now be entered. Exit the passcode message with the ESCAPE key
and program the appropriate setpoints. If no keypress occurs for 30 minutes,
access will be disabled and the passcode must be re-entered. Removing the set-
point access jumper or setting SETPOINT ACCESS to “Restricted” also disables set-
point access immediately.
If a new passcode is required, gain setpoint access by entering the current valid
passcode. Press MESSAGE DOWN to display the CHANGE PASSCODE message and
follow the directions. If an invalid passcode is entered, the encrypted passcode is
Setpoints
viewable by pressing HELP. Consult GE Multilin with this number if the currently
programmed passcode is unknown. The passcode can be determined with
deciphering software.
messages. This time can be modified to ensure messages remain on the screen
long enough during programming or reading of actual values.
• PARAMETER AVERAGES CALCULATION PERIOD: The period of time over
which the parameter averages are calculated may be adjusted with this
setpoint. The calculation is a sliding window.
• TEMPERATURE DISPLAY: Measurements of temperature may be displayed in
either Celsius or Fahrenheit. Each actual value temperature message will be
denoted by either °C for Celsius or °F for Fahrenheit. RTD setpoints are always
displayed in Celsius.
• WAVEFORM TRIGGER: The trigger setpoint allows the user to adjust how
many pre-trip and post-trip cycles are stored in the waveform memory when a
trip occurs. A value of 25%, for example, when the WAVEFORM MEMORY BUFFER is
“7 x 16" cycles, would produce a waveform of 4 pre-trip cycles and 12 post-trip
cycles.
• WAVEFORM MEMORY BUFFER: Selects the partitioning of the waveform
memory. The first number indicates the number of events and the second
number, the number of cycles. The relay captures 12 samples per cycle. When
more waveform captures occur than the available storage, the oldest data will
be discarded.
Setpoints
COMPUTER RS485 Range: 300, 1200, 2400, 4800, 9600,
MESSAGE 19200
BAUD RATE: 9600
b) Ethernet Communications
The following setpoints appear when the relay is ordered with the Ethernet (T)
option.
PATH: SETPOINTS Z S1 489 SETUP ZV COMMUNICATIONS
The IP addresses are used with the Modbus protocol. Enter the dedicated IP, subnet
IP, and gateway IP addresses provided by the network administrator.
To ensure optimal response from the relay, the typical connection timeout should be
set as indicated in the following table:
TCP/IP sessions Timeout setting
Setpoints
up to 2 2 seconds
up to 4 3 seconds
NOTE
Real Time Clock PATH: SETPOINTS Z S1 489 SETUP ZV REAL TIME CLOCK
For events that are recorded by the event recorder to be correctly time/date
stamped, the correct time and date must be entered. A battery backed internal
clock runs continuously even when power is off. It has the same accuracy as an
electronic watch approximately ±1 minute per month. It must be periodically
corrected either manually through the front panel or via the clock update command
over the RS485 serial link. If the approximate time an event occurred without
synchronization to other relays is sufficient, then entry of time/date from the front
panel keys is adequate.
If the RS485 serial communication link is used then all the relays can keep time in
synchronization with each other. A new clock time is pre-loaded into the memory
map via the RS485 communications port by a remote computer to each relay
connected on the communications channel. The computer broadcasts (address 0) a
“set clock” command to all relays. Then all relays in the system begin timing at the
A: 0 B: 0 Range: N/A
MESSAGE
C: 0 Amps
Setpoints
DATE: 01/01/1995 Range: N/A
MESSAGE
TIME: 12:00:00
6. To verify that the message was added, view the last message under the S1 489
SETUP ZV DEFAULT MESSAGES menu.
Default messages can be removed from the default message list, as follows:
1. Enter the correct passcode at S1 489 SETUP Z PASSCODE Z ENTER PASSCODE FOR
ACCESS to allow setpoint entry (unless the passcode has already been entered
or unless the passcode is “0” defeating the passcode security feature).
2. Select the message to remove from the default message list under the S1 489
SETUP ZV DEFAULT MESSAGES menu.
3. Select the default message to remove and press ENTER. The relay will display
PRESS [ENTER] TO REMOVE MESSAGE.
4. Press ENTER while this message is displayed to remove the current message out
of the default message list.
5. If the procedure was followed correctly, the DEFAULT MESSAGE HAS BEEN
REVOVED flash message is displayed.
Setpoints
• CLEAR MWh and Mvarh METERS: Executing this command will clear the MWh
and Mvarh metering to zero.
• CLEAR PEAK DEMAND DATA: Execute this command to clear peak demand
values.
• CLEAR RTD MAXIMUMS: All maximum RTD temperature measurements are
stored and updated each time a new maximum temperature is established.
Execute this command to clear the maximum values.
• CLEAR ANALOG I/P MIN/MAX: The minimum and maximum analog input
values are stored for each Analog Input. Those minimum and maximum values
may be cleared at any time.
• CLEAR TRIP COUNTERS: There are counters for each possible type of trip.
Those counters may be cleared by executing this command.
• CLEAR EVENT RECORD: The event recorder saves the last 256 events,
automatically overwriting the oldest event. If desired, all events can be cleared
using this command to prevent confusion with old information.
• CLEAR GENERATOR INFORMATION: The number of thermal resets and the
total generator running hours can be viewed in actual values. On a new
installation, or if new equipment is installed, this information is cleared through
this setpoint.
• CLEAR BREAKER INFORMATION: The total number of breaker operations can
be viewed in actual values. On a new installation or if maintenance work is done
on the breaker, this accumulator can be cleared with this setpoint.
S2 System Setup
Current Sensing PATH: SETPOINTS ZV S2 SYSTEM SETUP Z CURRENT SENSING
that potential fault current does not exceed 20 times the primary rating. When
relaying class CTs are purchased, this precaution will ensure that the Ground CT
does not saturate under fault conditions.
The 489 uses a nominal CT primary rating of 5 A for calculation of pickup levels.
For example, if the distribution transformer ratio is 13200:480 and the auxiliary VT
ratio is 600:120, the NEUTRAL VT RATIO setpoint is calculated as:
NEUTRAL VT RATIO = Distribution Transformer Ratio × Auxiliary VT Ratio : 1
13200 600 (EQ 5.1)
= ------------------- × ----------- : 1 = 137.50 : 1
480 120
Therefore, set NEUTRAL VT RATIO to 137.50:1
As a safeguard, when a unit is received from the factory, the PHASE CT PRIMARY and
Generator Parameters setpoints will be defaulted to “--------”, indicating they are
not programmed. The 489 indicates that it was never programmed. Once these
values are entered, the 489 will be in service. All elements associated with power
quantities are programmed in per unit values calculated from the rated MVA and
Setpoints
power factor. The generator full load amps (FLA) is calculated as
Generator Rated MVA
Generator FLA = --------------------------------------------------------------------------------------------------------------------------------- (EQ 5.2)
3 × Generator Rated Phase-Phase Voltage
All voltage protection features that require a level setpoint are programmed in per
unit of the rated generator phase-phase voltage.The nominal system frequency
must be entered here. This setpoint allows the 489 to determine the internal
sampling rate for maximum accuracy. If the sequence of phase rotation for a given
system is ACB rather than the standard ABC, the system phase sequence setpoint
may be used to accommodate this rotation. This setpoint allows the 489 to properly
calculate phase reversal and negative sequence quantities.
If enabled, this feature will allow the user to initiate a generator startup or
shutdown via the RS232/RS485 communication ports. Refer to GE publication
number GEK-106495: 489 Communications Guide for command formats. When a
startup command is issued, the auxiliary relay(s) assigned for starting control will
be activated for 1 second to initiate startup. When a stop command is issued, the
assigned relay(s) will be activated for 1 second to initiate a shutdown.
S3 Digital Inputs
Description The 489 has nine (9) digital inputs for use with external contacts. Two of the 489
digital inputs have been pre-assigned as inputs having a specific function. The
Access Switch does not have any setpoint messages associated with it. The Breaker
Status input, may be configured for either an 'a' or 'b' auxiliary contact. The
remaining seven digital inputs are assignable; that is to say, each input may be
assigned to any of a number of different functions. Some of those functions are very
specific, others may be programmed to adapt to user requirements.
Terminals C1 and C2 must be shorted to allow changing of any setpoint values from
the front panel keypad. This safeguard is in addition to the setpoint passcode
WARNING feature, which functions independently (see the S1 489 SETUP Z PASSCODE menu). The
access switch has no effect on setpoint programming from the RS232 and RS485
serial communications ports.
This input is necessary for all installations. The 489 determines when the generator
is online or offline based on the Breaker Status input. Once 'Breaker Auxiliary a' is
Setpoints
chosen, terminals C3 and C4 will be monitored to detect the state of the machine
main breaker, open signifying the breaker is open and shorted signifying the breaker
is closed. Once “Breaker Auxiliary b” is chosen, terminals C3 and C4 will be
monitored to detect the state of the breaker, shorted signifying the breaker is open
and open signifying the breaker is closed.
Setpoints
ALARM DELAY: 0.5 s
If an input is assigned to the Tachometer function, it may not be assigned via the
ASSIGN DIGITAL INPUT setpoint.
NOTE
The seven General Input functions are flexible enough to meet most of the desired
digital input requirements. The asserted state and the name of the digital inputs are
programmable. To disable the input functions when the generator is offline, until
some time after the generator is brought online, a block time should be set. The
input functions will be enabled once the block delay has expired. A value of “0 s” for
the BLOCK INPUT FROM ONLINE block time indicates that the input functions are always
enabled while the generator is offline as well as online.
Inputs may be configured for control, alarm, or trip. If the control feature is
enabled, the assigned output relay(s) operate when the input is asserted. If the
PULSED CONTROL RELAY DWELL TIME is set to “0”, the output relay(s) operate only while
the input is asserted. However, if a dwell time is assigned, the output relay(s)
operate as soon as the input is asserted for a period of time specified by the
setpoint. If an alarm or trip is enabled and the input is asserted, an alarm or trip will
occur after the specified delay.
Once an input is assigned to the Remote Reset function, shorting that input will
reset any latched trips or alarms that may be active, provided that any thermal
lockout time has expired and the condition that caused the alarm or trip is no longer
present.
If an input is assigned to the tachometer function, it may not be used here.
Once the 489 is in service, it may be tested from time to time as part of a regular
maintenance schedule. The unit will have accumulated statistical information
relating historically to generator and breaker operation. This information includes:
last trip data, peak demand data, MWh and Mvarh metering, parameter averages,
RTD maximums, analog input minimums and maximums, number of trips, number
of trips by type, number of breaker operations, the number of thermal resets, total
generator running hours, and the event record. When the unit is under test and one
of the inputs is assigned to the Test Input function, shorting that input will prevent
all of this data from being corrupted or updated.
If an input is assigned to the tachometer function, it may not be used here.
Setpoints
The following chart illustrates the available Group 2 (alternate group) setpoints
2 SETPOINTS [Z] 2 SETPOINTS [Z] 2 SETPOINTS [Z] 2 SETPOINTS [Z] 2 SETPOINTS [Z]
S5 CURRENT ELEM. S6 VOLTAGE ELEM. S7 POWER ELEMENTS S8 RTD TEMPERATURE S9 THERMAL MODEL
2 OVERCURRENT [Z] 2 UNDERVOLTAGE [Z] 2 REACTIVE [Z] 2 RTD [Z] 2 MODEL [Z]
ALARM POWER TYPES SETUP
2 OFFLINE [Z] 2 OVERVOLTAGE [Z] 2 REVERSE [Z] 2 RTD #1 [Z] 2 THERMAL [Z]
OVERCURRENT POWER ELEMENTS
2 DISTANCE [Z]
ELEMENT
The active group can be selected using the ACTIVATE SETPOINT GROUP setpoint or the
assigned digital input (shorting that input will activate the alternate set of protection
Setpoints
setpoints, Group 2). In the event of a conflict between the ACTIVATE SETPOINT GROUP
setpoint or the assigned digital input, Group 2 will be activated. The LED indicator
on the faceplate of the 489 will indicate when the alternate setpoints are active in
the protection scheme. Changing the active setpoint group will be logged as an
event. Independently, the setpoints in either group can be viewed and/or edited
using the EDIT SETPOINT GROUP setpoint. Headers for each setpoint message
subgroup that has dual settings will be denoted by a superscript number indicating
which setpoint group is being viewed or edited. Also, when a setpoint that has dual
settings is stored, the flash message that appears will indicate which setpoint group
setting has been changed.
forward power level, or exceeds the reverse power level for the period of time
specified, a trip will occur. This time delay will typically be shorter than that used for
the standard reverse power or low forward power elements. The level is
programmed in per unit of generator rated MW calculated from the rated MVA and
rated power factor. If the VT type is selected as None, the sequential trip element
will operate as a simple timer. Once the input has been shorted for the period of
time specified by the delay, a trip will occur.
The minimum magnitude of power measurement is determined by the phase CT
minimum of 2% rated CT primary. If the level for reverse power is set below that
NOTE level, a trip will only occur once the phase current exceeds the 2% cutoff.
Users are cautioned that a reverse power element may not provide reliable
indication when set to a very low setting, particularly under conditions of large
reactive loading on the generator. Under such conditions, low forward power is a
more reliable element.
Setpoints
This feature may be used to trigger the waveform capture from an external contact.
When one of the inputs is assigned to the Waveform Capture function, shorting that
input will trigger the waveform.
Ground Switch Status PATH: SETPOINTS ZV S3 DIGITAL INPUTS ZV GND SWITCH STATUS
S4 Output Relays
Description Five of the six output relays are always non-failsafe; the 6 Service relay is always
failsafe. As a failsafe, the 6 Service relay will be energized normally and de-energize
when called upon to operate. It will also de-energize when control power to the 489
is lost and therefore, be in its operated state. All other relays, being non-failsafe,
will be de-energized normally and energize when called upon to operate. Obviously,
when control power is lost to the 489, the output relays must be de-energized and
therefore, they will be in their non-operated state. Shorting bars in the drawout
case ensure that when the 489 is drawn out, no trip or alarm occurs. The 6 Service
output will however indicate that the 489 has been drawn out.
Relay Reset Mode PATH: SETPOINTS ZV S4 OUTPUT RELAYS Z RELAY RESET MODE
Unlatched trips and alarms will reset automatically once the condition is no longer
present. Latched trip and alarm features may be reset at any time, providing that
the condition that caused the trip or alarm is no longer present and any lockout time
has expired. If any condition may be reset, the Reset Possible LED will be lit. The
relays may be programmed to All Resets which allows reset from the front keypad or
the remote reset digital input or the communications port. Optionally, they may be
programmed to reset by the Remote Reset Only (by the remote reset digital input or
the communications port).
For example, selected trips such as Instantaneous Overcurrent and Ground Fault
may be assigned to output relay 2 so that they may only be reset via. the Remote
Reset digital input or the communication port. The Remote Reset terminals would be
Setpoints
S5 Current Elements
Inverse Time a) Description
Overcurrent Curve The 489 inverse time overcurrent curves may be either ANSI, IEC, or GE Type IAC
Characteristics standard curve shapes. This allows for simplified coordination with downstream
devices. If however, none of these curve shapes is adequate, the FlexCurve™ may
be used to customize the inverse time curve characteristics. Definite time is also an
option that may be appropriate if only simple protection is required.
A multiplier setpoint allows selection of a multiple of the base curve shape that is
selected with the curve shape setpoint. Unlike the electromechanical time dial
equivalent, trip times are directly proportional to the time multiplier setting value.
For example, all trip times for a multiplier of 10 are 10 times the multiplier 1 or base
curve values. Setting the multiplier to zero results in an instantaneous response to
all current levels above pickup.
Regardless of the trip time that results from the curve multiplier setpoint,
the 489 cannot trip any quicker than one to two cycles plus the operate
NOTE time of the output relay.
Time overcurrent tripping time calculations are made with an internal “energy
capacity” memory variable. When this variable indicates that the energy capacity
has reached 100%, a time overcurrent trip is generated. If less than 100% is
accumulated in this variable and the current falls below the dropout threshold of 97
to 98% of the pickup value, the variable must be reduced. Two methods of this
resetting operation are available, “Instantaneous” and “Linear”. The Instantaneous
selection is intended for applications with other relays, such as most static units,
which set the energy capacity directly to zero when the current falls below the reset
threshold. The Linear selection can be used where the 489 must coordinate with
electromechanical units. With this setting, the energy capacity variable is
decremented according to the following equation.
E × M × CR
T RESET = ----------------------------
- (EQ 5.3)
100
where: TRESET = reset time in seconds
E = energy capacity reached (in %)
M = curve multiplier
CR= characteristic constant (5 for ANSI, IAC, Definite Time and
FlexCurves™, 8 for IEC curves)
b) ANSI Curves
The ANSI time overcurrent curve shapes conform to industry standard curves and fit
into the ANSI C37.90 curve classifications for extremely, very, normally, and
moderately inverse. The 489 ANSI curves are derived from the formula:
⎛ B D E ⎞
Setpoints
T = M × ⎜ A + ----------------------------------------- + ------------------------------------------------- + -------------------------------------------------⎟ (EQ 5.4)
( I ⁄ I pickup ) – C ( ( I ⁄ I pickup ) – C ) 2 ( ( I ⁄ I pickup ) – C ) ⎠ 3
⎝
c) IEC Curves
For European applications, the relay offers the four standard curves defined in IEC
255-4 and British standard BS142. These are defined as IEC Curve A, IEC Curve B,
IEC Curve C, and Short Inverse. The formula for these curves is:
⎛ K ⎞
T = M × ⎜ -------------------------------------------
E
⎟ (EQ 5.5)
⎝ ( I ⁄ I pickup ) – 1⎠
d) IAC Curves
The curves for the General Electric type IAC relay family are derived from the
formula:
⎛ B D E ⎞
T = M × ⎜ A + ----------------------------------------- + ------------------------------------------------- + -------------------------------------------------⎟ (EQ 5.6)
( I ⁄ I pickup ) – C ( ( I ⁄ I pickup ) – C ) 2 ( ( I ⁄ I pickup ) – C ) ⎠ 3
⎝
e) FlexCurve™
The custom FlexCurve™ has setpoints for entering times to trip at the following
current levels: 1.03, 1.05, 1.1 to 6.0 in steps of 0.1 and 6.5 to 20.0 in steps of 0.5.
The relay then converts these points to a continuous curve by linear interpolation
between data points. To enter a custom FlexCurve™, read off each individual point
from a time overcurrent coordination drawing and enter it into a table as shown.
Then transfer each individual point to the 489 using either the EnerVista 489 Setup
software or the front panel keys and display.
Setpoints
f) Definite Time Curve
The definite time curve shape causes a trip as soon as the pickup level is exceeded
for a specified period of time. The base definite time curve delay is 100 ms. The
curve multiplier of 0.00 to 1000.00 makes this delay adjustable from instantaneous
to 100.00 seconds in steps of 1 ms.
T = M × 100 ms, when I > I pickup (EQ 5.7)
programmed as unlatched, the alarm will reset itself when the overcurrent condition
is no longer present. If programmed as latched, once the overcurrent condition is
gone, the reset key must be pressed to reset the alarm. The generator FLA is
calculated as:
Generator Rated MVA
Generator FLA = --------------------------------------------------------------------------------------------------------------------------------- (EQ 5.8)
3 × Generator Rated Phase-Phase Voltage
event of a low impedance fault, the differential element will still shutdown the
generator quickly.
If the unit auxiliary transformer is on the generator side of the breaker, the
pickup level must be set greater than the unit auxiliary load.
NOTE
The logic diagram for the inadvertent energization protection feature is shown
below. The feature may be armed when all of the phase voltages fall below the
undervoltage pickup level and the unit is offline. This would be the case when the
VTs are on the generator side of the disconnect device. If however, the VTs are on
the power system side of the disconnect device, the feature should be armed if all of
the phase voltages fall below the undervoltage pickup level or the unit is offline.
When the feature is armed, if any one of the phase currents measured at the output
CTs exceeds the overcurrent level programmed, a trip will occur.
This feature requires 5 seconds to arm, 250 ms to disarm.
NOTE
Protection can be provided for poor synchronization by using the “U/V or Offline”
arming signal. During normal synchronization, there should be relatively low current
measured. If however, synchronization is attempted when conditions are not
appropriate, a large current that is measured within 250 ms after the generator is
placed online would result in a trip.
OR
AND
Arming Signal = U/V or Offline
808731A1.CDR
Setpoints
VOLTAGE LOWER
MESSAGE VOLTAGE RESTRAINT is "Yes"
LIMIT: 10%
If the primary system protection fails to properly isolate phase faults, the voltage
restrained overcurrent acts as system backup protection. The magnitude of each
phase current measured at the output CTs is used to time out against an inverse
time curve. The 489 inverse time curve for this element may be either ANSI, IEC, or
GE Type IAC standard curve shapes. This allows for simplified coordination with
downstream devices. If these curve shapes are not adequate, FlexCurves™ may be
used to customize the inverse time curve characteristics.
The voltage restraint feature lowers the pickup value of each phase time overcurrent
element in a fixed relationship (see figure below) with the corresponding input
voltage to a minimum pickup of 0.15 × CT. The VOLTAGE LOWER LIMIT setpoint
prevents very rapid tripping prior to primary protection clearing a fault when voltage
restraint is enabled and severe close-in fault has occurred. If voltage restraint is not
required, select “No” for this setpoint. If the VT type is selected as “None” or a VT
fuse loss is detected, the voltage restraint is ignored and the element operates as
simple phase overcurrent.
A fuse failure is detected within 99 ms; therefore, any voltage restrained
overcurrent trip should have a time delay of 100 ms or more or nuisance tripping on
NOTE fuse loss could occur.
For example, to determine the voltage restrained phase overcurrent pickup level
under the following situation:
• PHASE OVERCURRENT PICKUP: “2.00 × CT”
• ENABLE VOLTAGE RESTRAINT: “Yes”
• Phase-Phase Voltage / Rated Phase-Phase Voltage = 0.4 p.u. V
The voltage restrained phase overcurrent pickup level is calculated as follows:
Pickup vrest = Phase OC Pickup × Voltage Rest. Pickup Multiplier × CT
(EQ 5.9)
= ( 2 × 0.4 ) × CT = 0.8 × CT
The 489 phase overcurrent restraint voltages and restraint characteristic are shown
below.
0.2
0.1
0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
808792A3.CDR
Phase-Phase Voltage / Rated Phase-Phase Voltage
Setpoints
persist before a trip is issued. The reset rate provides a thermal memory of previous
unbalance conditions. It is the linear reset time from the threshold of trip.
Unusually high negative sequence current levels may be caused by
incorrect phase CT wiring.
NOTE
808791A2.CDR
The 489 ground overcurrent feature consists of both an alarm and a trip element.
The magnitude of measured ground current is used to time out against the definite
time alarm or inverse time curve trip. The 489 inverse time curve for this element
may be either ANSI, IEC, or GE Type IAC standard curve shapes. This allows for
simplified coordination with downstream devices. If however, none of these curves
shapes is adequate, the FlexCurve™ may be used to customize the inverse time
curve characteristics. If the Ground CT is selected as “None”, the ground overcurrent
protection is disabled.
The pickup level for the ground current elements is programmable as a
multiple of the CT. The 50:0.025 CT is intended for very sensitive detection
NOTE of ground faults and its nominal CT rating for the 489 is 50:0.025.
For example, if the ground CT is 50:0.025, a pickup of 0.20 would be 0.20 × 50 =
10 A primary. If the ground CT is 50:0.025, a pickup of 0.05 would be 0.05 × 50 =
2.5 A primary.
The 489 differential element consists of the well known, dual slope, percent restraint
characteristic. A differential signal is derived from the phasor sum of the currents on
either side of the machine. A restraint signal is derived from the average of the
magnitudes of these two currents. An internal flag (DIFF) is asserted when the
differential signal crosses the operating characteristic as defined by the magnitude
of the restraint signal. The DIFF flag produces a relay operation.
External faults near generators would typically result in very large time constants of
DC components in the fault currents. Also, when energizing a step-up transformer,
the inrush current being limited only by the machine impedance may be significant
and may last for a very long time. This creates a real danger of CT saturation. In
order to enhance the security of the relay under these circumstances a directional
Setpoints
check is employed.
When the generator is subjected to an external fault the currents will be large but
the CTs will initially reproduce the fault current without distortion. Consequently the
relay will see a large restraint signal coupled with a small differential signal. This
condition is used as an indication of the possible onset of CT saturation. An internal
flag (SC) will be set at this time. Once the SC flag has been set, a comparison of the
phase angles of the currents on either side of the generator is carried out. An
external fault is inferred if the phase comparison indicates both currents are flowing
in the same direction. An internal fault is inferred if the phase comparison indicates
that the currents are flowing in opposite directions. In this case an internal flag
(DIR) is set.
If the SC flag is not set, then the relay will operate for a DIFF flag alone. If the SC
flag is set then the differential flag is supervised by the directional flag. The
requirement for both the DIFF flag and the DIR flag during the period where CT
saturation is likely therefore enhances the security of the scheme.
The differential element for phase A will operate when:
I operate > k × I restraint (EQ 5.12)
IA + Ia
I restraint = ----------------------
- = restraint current (EQ 5.14)
2
k = characteristic slope of the differential element in percent
k = Slope1 if I R < 2 × CT ; k = Slope2 if I R ≥ 2 × CT (EQ 5.15)
Differential elements for phase B and phase C operate in the same manner.
0.9
(multiples of CT)
0.8
0.7
OPERATE Slope 2 = 20%
0.6 REGION
0.5
0.4
OPERATE
0.3
0.2
Slope 1 = 10%
I
Minimum Pickup = 0.10 x CT
0.1
0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
The SUPERVISE WITH DIGITAL INPUTS setpoint is seen only if a digital input assigned to
Ground Switch Status.
NOTE
The 489 detects ground directional by using two measurement quantities: V0 and
I0. The angle between these quantities determines if a ground fault is within the
generator or not. This function should be coordinated with the 59GN element (95%
stator ground protection) to ensure proper operation of the element. Particularly,
this element should be faster. This element must use a core balance CT to derive the
I0 signal. Polarity is critical in this element. The protection element is blocked for
neutral voltages, V0, below 2.0 V secondary.
The pickup level for the ground current elements is programmable as a multiple of
the CT. The 50:0.025 CT is intended for very sensitive detection of ground faults and
NOTE its nominal CT rating for the 489 is 50:0.025.
For example, if the ground CT is 50:0.025, a pickup of 0.20 would be 0.20 × 50 =
10 A primary. If the ground CT is 50:0.025, a pickup of 0.05 would be 0.05 × 50 =
2.5 A primary.. Refer to Stator Ground Fault on page 8–1 for additional details.
AUXILIARY
CONTACT
GROUNDING SWITCH
C(B) C(B)
A A
59G
B(C) B(C)
I0
TO Vneutral OF EACH 489 TO 50:0.025
50:0.025 GROUND
INPUTS
808812A3.CDR
Setpoints
FIGURE 5–5: Ground Directional Detection
If any individual phase current exceeds the pickup level for the specified trip time a
trip will occur if the feature is enabled. The element operates in both online and
offline conditions. This element can be used as a backup feature to other protection
elements. In situations where generators are connected in parallel this element
would be set above the maximum current contribution from the generator on which
the protection is installed. With this setting, the element would provide proper
selective tripping. The basic operating time of the element with no time delay is 50
ms at 50/60 Hz.
S6 Voltage Elements
Undervoltage PATH: SETPOINTS ZV S6 VOLTAGE ELEM. Z UNDERVOLTAGE
The undervoltage elements may be used for protection of the generator and/or its
auxiliary equipment during prolonged undervoltage conditions. They are active only
when the generator is online. The alarm element is definite time and the trip
element can be definite time or a curve. When the magnitude of the average phase-
phase voltage is less than the pickup × the generator rated phase-phase voltage,
the element will begin to time out. If the time expires, a trip or alarm will occur.
The curve reset rate is a linear reset time from the threshold of trip. If the VT type is
selected as None, VT fuse loss is detected, or the magnitude of I1< 7.5% CT, the
undervoltage protection is disabled. The pickup levels are insensitive to frequency
over the range of 5 to 90 Hz.
The formula for the undervoltage curve is:
D
T = -------------------------------------- , when V < V pickup (EQ 5.18)
1 – V ⁄ V pickup
1000 10
100 1
10
0.1
0 0.2 0.4 0.6 0.8 1
Setpoints
ASSIGN ALARM Range: Any combination of Relays 2 to
MESSAGE 5
RELAYS (2-5): ---5
The overvoltage elements may be used for protection of the generator and/or its
auxiliary equipment during prolonged overvoltage conditions. They are always
active (when the generator is offline or online). The alarm element is definite time
and the trip element can be either definite time or an inverse time curve. When the
average of the measured phase-phase voltages rises above the pickup level x the
generator rated phase-phase voltage, the element will begin to time out. If the time
expires, a trip or alarm will occur. The reset rate is a linear reset time from the
threshold of trip. The pickup levels are insensitive to frequency over the range of 5
to 90 Hz.
The formula for the curve is:
D
T = ------------------------------------------- , when V > V pickup (EQ 5.19)
( V ⁄ V pickup ) – 1
1000
100
Time to Trip (seconds)
10 10
1 1
0.3
0.1 0.1
Setpoints
The Volts Per Hertz elements may be used generator and unit transformer
protection. They are active as soon as the magnitude and frequency of Vab is
measurable. The alarm element is definite time; the trip element can be definite
time or a curve. Once the V/Hz measurement Vab exceeds the pickup level for the
specified time, a trip or alarm will occur. The reset rate is a linear reset time from
the threshold of trip and should be set to match cooling characteristics of the
protected equipment. The measurement of V/Hz will be accurate through a
frequency range of 5 to 90 Hz. Settings less than 1.00 only apply for special
generators such as short circuit testing machines.
The formula for Volts/Hertz Curve 1 is:
D V
T = -------------------------------------------------------------------------- , when ---- > Pickup (EQ 5.20)
V⁄F
⎛ ------------------------------------------------------- ⎞2 – 1 F
⎝ ( V nom ⁄ F s ) × Pickup⎠
Setpoints
100
Time to Trip (seconds)
10
10
0.1 0.3
0.1
0.01
1.00 1.20 1.40 1.60 1.80 2.00
Multiples of Volts/Hertz Pickup
808743A1-X1.CDR
The V/Hz Curve 2 trip curves are shown below for delay settings of 0.1, 0.3, 1, 3,
and 10 seconds.
1000
100
1 1
0.3
0.1 0.1
1.00 1.20 1.40 1.60 1.80 2.00
Multiples of Volts/Hertz Pickup
808743A1-X2.CDR
1000
Time to Trip (seconds)
100
10
TIME DELAY SETTING
10
3
1
1
0.3
0.1
0.1
1.00 1.20 1.40 1.60 1.80 2.00
Multiples of Voltz/Hertz Pickup
808743A1-X3.CDR
The 489 can detect the phase rotation of the three phase voltages. A trip will occur
within 200 ms if the Phase Reversal feature is turned on, the generator is offline,
each of the phase-phase voltages is greater than 50% of the generator rated phase-
phase voltage and the phase rotation is not the same as the setpoint. Loss of VT
fuses cannot be detected when the generator is offline and could lead to
maloperation of this element. If the VT type is selected as “None”, the phase
reversal protection is disabled.
Setpoints
ALARM LEVEL: 59.50 Hz
Setpoints
NEUTRAL O/V TRIP Range: Curve, Definite Time
MESSAGE
ELEM.: Time
The SUPERVISE WITH DIGITAL INPUT setpoint is seen only if a digital input assigned to
Ground Switch Status.
NOTE
The neutral overvoltage function responds to fundamental frequency voltage at the
generator neutral. It provides ground fault protection for approximately 95% of the
stator windings. 100% protection is provided when this element is used in
conjunction with the Neutral Undervoltage (3rd harmonic) function. The alarm
element is definite time and the trip element can be either definite time or an
inverse time curve. When the neutral voltage rises above the pickup level the
element will begin to time out. If the time expires an alarm or trip will occur. The
reset rate is a linear reset time from the threshold of trip. The alarm and trip levels
are programmable in terms of Neutral VT secondary voltage.
The formula for the curve is:
D
T = ------------------------------------------- when V > V pickup (EQ 5.23)
( V ⁄ V pickup ) – 1
1000
100
1 1
0.3
0.1 0.1
1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2
Multiples of Overvoltage Pickup
808741A1.CDR
AUXILIARY CONTACT
TO DIGITAL INPUT FOR
NEUTRAL O/V SUPERVISION
GROUNDING SWITCH
Setpoints
C(B) C(B)
A A
59G
B(C) B(C)
GENERATOR 1 GENERATOR 2
808816A3.CDR
Neutral Undervoltage PATH: SETPOINTS ZV S6 VOLTAGE ELEM. ZV NEUTRAL U/V (3RD HARMONIC)
1 NEUTRAL U/V [Z] LOW POWER BLOCKING Range: 0.02 to 0.99 × Rated MW in
(3rd HARMONIC) LEVEL: 0.05 x Rated MW steps of 0.01
Setpoints
The LOW POWER BLOCKING LEVEL, NEUTRAL U/V ALARM LEVEL, and NEUTRAL U/V TRIP
LEVEL setpoints are seen only if the S2 SYSTEM SETUP ZV VOLTAGE ZV VT CONNECTION
NOTE setpoint is “Delta”
The neutral undervoltage function responds to 3rd harmonic voltage measured at
the generator neutral and output terminals. When used in conjunction with the
Neutral Overvoltage (fundamental frequency) function, it provides 100% ground
fault protection of the stator windings.
For Wye connected VTs:
Since the amount of third harmonic voltage that appears in the neutral is both load
and machine dependent, the protection method of choice is an adaptive method. If
the phase VT connection is wye, the following formula is used to create an adaptive
neutral undervoltage pickup level based on the amount of third harmonic that
appears at the generator terminals.
V N3
- ≤ 0.15
--------------------------------------- which simplifies to V P3 ≥ 17V N3 (EQ 5.24)
( V P3 ⁄ 3 ) + V N3
The 489 tests the following permissives prior to testing the basic operating equation
to ensure that VN3’ should be of a measurable magnitude for an unfaulted
generator:
Neutral VT Ratio
V P3 ′ > 0.25 V and V P3 ′ ≥ Threshold × 17 × ------------------------------------------------- (EQ 5.25)
Phase VT Ratio
where: VN3 = magnitude of the third harmonic voltage at generator neutral;
VP3 = magnitude of the third harmonic voltage at the generator terminals
VP3´ = VT secondary magnitude of the third harmonic voltage measured at
the generator terminals;
VN3´ = VT sec. magnitude of 3rd harmonic voltage at generator neutral;
Threshold = 0.15 V for the alarm element and 0.1875 V for the trip element
The VOLTAGE LEVEL setpoint is seen only if ENABLE VOLTAGE SUPERVISION is set to
“Yes”.
NOTE
Loss of excitation is detected with an impedance element. When the impedance falls
within the impedance circle for the specified delay time, a trip will occur if it is
enabled. Circles 1 and/or 2 can be tuned to a particular system. The larger circle
diameter should be set to the synchronous reactance of the generator, xd, and the
circle offset to the generator transient reactance x’d / 2. Typically the smaller circle
(if used) is set to minimum time with a diameter set to 0.7xd and an offset of x’d / 2.
This feature is blocked if voltage supervision is enabled and the generator voltage is
above the VOLTAGE LEVEL setpoint. The trip feature is supervised by minimum
current of 0.05 × CT. Note that the Loss of Excitation element will be blocked if there
is a VT fuse failure or if the generator is offline. Also, it uses output CT inputs.
The secondary phase-phase loss of excitation impedance is defined as:
V AB
Z loe = ----------------- = M loe ∠θ loe (EQ 5.26)
IA – IB
Setpoints
FIGURE 5–10: Loss of Excitation R-X Diagram
The distance protection function (ANSI device 21) implements two zones of mho
phase-to-phase distance protection (six elements total) using the conventional
phase comparator approach, with the polarizing voltage derived from the pre-fault
positive sequence voltage of the protected loop. This protection is intended as
backup for the primary line protection. The elements make use of the neutral-end
current signals and the generator terminal voltage signals (see figure below), thus
providing some protection for internal and unit transformer faults. In systems with a
delta-wye transformer (DY330°), the appropriate transformations of voltage and
current signals are implemented internally to allow proper detection of transformer
high-side phase-to-phase faults. The reach setting is the positive sequence
impedance to be covered, per phase, expressed in secondary ohms. The same
transformation shown for the Loss of Excitation element can be used to calculate the
desired settings as functions of the primary-side impedances.
The elements have a basic operating time of 150 ms. A VT fuse failure could cause a
maloperation of a distance element unless the element is supervised by the VTFF
element. In order to prevent nuisance tripping the elements require a minimum
phase current of 0.05 x CT.
Protection Zone 1
Protection Zone 2
Setpoints
Neutral End CT
52
Terminal VT
489
Relay
808740A1.CDR
The first zone is typically used to provide a backup protection for a step-up
transformer and generator system bus protection (generator impedance should not
be included into reach setting). The reach is set to cover the step-up transformer
impedance with some margin, say 25%. The time delay should be coordinated with
step up transformer and bus backup protection.
The second zone reach is typically set to cover the longest transmission line or
feeder leaving the generating station. Care must be taken for possible under-
reaching effects due to the fault contribution from other lines or generators. The
element is intended for backup protection and therefore time delay should always
be included. This element is typically set to coordinate with the longest operating
time of the system distance relays protecting lines leaving station.
The measuring point of the element is defined by the location of the VT and CT as
shown in FIGURE 5–11: Distance Element Setup on page 5–46. Therefore, the
impedance of the step-up transformer should be included and the impedance of the
generator should not be included. Care should also be taken to ensure the apparent
impedance seen by the element when the machine is operating at worst-case load
and power factor does not encroach into the operating characteristic. The reach
setting is in secondary ohms. The minimum operating time of the element is 150 ms
to coordinate with VTFF operating time (99 ms).
Setpoints
etting
ZR
Reach s
Characteristic
angle
ZR*0.125
808838A2.CDR
S7 Power Elements
Power Measurement Generation of power will be displayed on the 489 as positive watts. By convention,
Conventions an induction generator normally requires reactive power from the system for
excitation. This is displayed on the 489 as negative vars. A synchronous generator
on the other hand has its own source of excitation and can be operated with either
lagging or leading power factor. This is displayed on the 489 as positive vars and
negative vars, respectively. All power quantities are measured from the phase-
phase voltage and the currents measured at the output CTs.
^
I 1
Setpoints
^
I 2
^
I 3
^
I 4
Setpoints
NEGATIVE Mvar TRIP Range: 0.02 to 2.01 × Rated in steps of
MESSAGE 0.01
LEVEL: 0.80 x Rated
If enabled, once the magnitude of 3-phase total power exceeds the Pickup Level in
Setpoints
the reverse direction (negative MW) for a period of time specified by the Delay, a
trip or alarm will occur. The level is programmed in per unit of generator rated MW
calculated from the rated MVA and rated power factor. If the generator is
accelerated from the power system rather than the prime mover, the reverse power
element may be blocked from start for a specified period of time. A value of zero for
the block time indicates that the reverse power protection is active as soon as both
current and voltage are measured regardless of whether the generator is online or
offline. If the VT type is selected as “None” or VT fuse loss is detected, the reverse
power protection is disabled.
The minimum magnitude of power measurement is determined by the phase CT
minimum of 2% rated CT primary. If the level for reverse power is set below that
NOTE level, a trip or alarm will only occur once the phase current exceeds the 2% cutoff.
Users are cautioned that a reverse power element may not provide reliable
indication when set to a very low setting, particularly under conditions of large
reactive loading on the generator. Under such conditions, low forward power is a
more reliable element.
Low Forward Power PATH: SETPOINTS ZV S7 POWER ELEMENTS ZV LOW FORWARD POWER
1 LOW FORWARD [Z] BLOCK LOW FWD POWER Range: 0 to 15000 s in steps of 1
POWER FROM ONLINE: 0 s
If enabled, once the magnitude of 3-phase total power in the forward direction
Setpoints
(+MW) falls below the Pickup Level for a period of time specified by the Delay, an
alarm will occur. The level is programmed in per unit of generator rated MW
calculated from the rated MVA and rated power factor. The low forward power
element is active only when the generator is online and will be blocked until the
generator is brought online, for a period of time defined by the setpoint Block Low
Fwd Power From Online. The pickup level should be set lower than expected
generator loading during normal operations. If the VT type is selected as “None” or
VT fuse loss is detected, the low forward power protection is disabled.
S8 RTD Temperature
RTD Types PATH: SETPOINTS ZV S8 RTD TEMPERATURE Z RTD TYPES
1 RTD TYPES [Z] STATOR RTD TYPE: Range: 100 Ohm Platinum, 120 Ohm
100 Ohm Platinum Nickel, 100 Ohm Nickel, 10
Ohm Copper
BEARING RTD TYPE: Range: as above
MESSAGE
100 Ohm Platinum
Each of the twelve RTDs may be configured as None or any one of four application
types, Stator, Bearing, Ambient, or Other. Each of those types may in turn be any
one of four different RTD types: 100 ohm Platinum, 120 ohm Nickel, 100 ohm
Nickel, 10 ohm Copper. The table below lists RTD resistance vs. temperature.
RTDs 1 through 6 default to Stator RTD type. There are individual alarm and trip
configurations for each RTD. This allows one of the RTDs to be turned off if it
malfunctions. The alarm level is normally set slightly above the normal running
temperature. The trip level is normally set at the insulation rating. Trip voting has
been added for extra reliability in the event of RTD malfunction. If enabled, a second
RTD must also exceed the trip temperature of the RTD being checked before a trip
will be issued. If the RTD is chosen to vote with itself, the voting feature is disabled.
Each RTD name may be changed if desired.
Setpoints
ASSIGN ALARM Range: Any combination of Relays 2 to
MESSAGE 5.
RELAYS (2-5): ---5
RTDs 7 through 10 default to Bearing RTD type. There are individual alarm and trip
configurations for each RTD. This allows one of the RTDs to be turned off if it
malfunctions. The alarm level and the trip level are normally set slightly above the
normal running temperature, but below the bearing temperature rating. Trip voting
has been added for extra reliability in the event of RTD malfunction. If enabled, a
second RTD must also exceed the trip temperature of the RTD being checked before
a trip will be issued. If the RTD is chosen to vote with itself, the voting feature is
disabled. Each RTD name may be changed if desired.
1 RTD #11 [Z] RTD #11 APPLICATION: Range: Stator, Bearing, Ambient, Other,
Other None
RTD 11 defaults to Other RTD type. The Other selection allows the RTD to be used to
Setpoints
monitor any temperature that might be required, either for a process or additional
bearings or other. There are individual alarm and trip configurations for this RTD.
Trip voting has been added for extra reliability in the event of RTD malfunction. If
enabled, a second RTD must also exceed the trip temperature of the RTD being
checked before a trip will be issued. If the RTD is chosen to vote with itself, the
voting feature is disabled. The RTD name may be changed if desired.
1 RTD #12 [Z] RTD #12 APPLICATION: Range: Stator, Bearing, Ambient, Other,
Ambient None
RTDs 12 defaults to Ambient RTD type. The Ambient selection allows the RTD to be
used to monitor ambient temperature. There are individual alarm and trip
configurations for this RTD. Trip voting has been added for extra reliability in the
event of RTD malfunction. If enabled, a second RTD must also exceed the trip
temperature of the RTD being checked before a trip will be issued. If the RTD is
chosen to vote with itself, the voting feature is disabled. The RTD name may be
changed if desired.
1 OPEN RTD [Z] OPEN RTD SENSOR: Range: Off, Latched, Unlatched
SENSOR Off
The 489 has an Open RTD Sensor Alarm. This alarm will look at all RTDs that have
either an alarm or trip programmed and determine if an RTD connection has been
broken. Any RTDs that do not have a trip or alarm associated with them will be
ignored for this feature. When a broken sensor is detected, the assigned output
relay will operate and a message will appear on the display identifying the RTD that
is broken. It is recommended that if this feature is used, the alarm be programmed
as latched so that intermittent RTDs are detected and corrective action may be
taken.
Setpoints
RTD Short/Low Temp PATH: SETPOINTS ZV S8 RTD TEMPERATURE ZV RTD SHORT/LOW TEMP
The 489 has an RTD Short/Low Temperature alarm. This alarm will look at all RTDs
that have either an alarm or trip programmed and determine if an RTD has either a
short or a very low temperature (less than –50°C). Any RTDs that do not have a trip
or alarm associated with them will be ignored for this feature. When a short/low
temperature is detected, the assigned output relay will operate and a message will
appear on the display identifying the RTD that caused the alarm. It is recommended
that if this feature is used, the alarm be programmed as latched so that intermittent
RTDs are detected and corrective action may be taken.
S9 Thermal Model
489 Thermal Model The thermal model of the 489 is primarily intended for induction generators,
especially those that start on the system bus in the same manner as induction
motors. However, some of the thermal model features may be used to model the
heating that occurs in synchronous generators during overload conditions.
One of the principle enemies of generator life is heat. Generator thermal limits are
dictated by the design of both the stator and the rotor. Induction generators that
start on the system bus have three modes of operation: locked rotor or stall (when
the rotor is not turning), acceleration (when the rotor is coming up to speed), and
generating (when the rotor turns at super-synchronous speed). Heating occurs in
the generator during each of these conditions in very distinct ways. Typically, during
the generator starting, locked rotor and acceleration conditions, the generator will
be rotor limited. That is to say that the rotor will approach its thermal limit before
the stator. Under locked rotor conditions, voltage is induced in the rotor at line
frequency, 50 or 60 Hz. This voltage causes a current to flow in the rotor, also at line
frequency, and the heat generated (I2R) is a function of the effective rotor
resistance. At 50 or 60 Hz, the reactance of the rotor cage causes the current to
flow at the outer edges of the rotor bars. The effective resistance of the rotor is
therefore at a maximum during a locked rotor condition as is rotor heating. When
the generator is running at above rated speed, the voltage induced in the rotor is at
a low frequency (approximately 1 Hz) and therefore, the effective resistance of the
rotor is reduced quite dramatically. During overloads, the generator thermal limit is
typically dictated by stator parameters. Some special generators might be all stator
or all rotor limited. During acceleration, the dynamic nature of the generator slip
dictates that rotor impedance is also dynamic, and a third thermal limit
characteristic is necessary.
The figure below illustrates typical thermal limit curves for induction motors. The
starting characteristic is shown for a high inertia load at 80% voltage. If the
machine started quicker, the distinct characteristics of the thermal limit curves
would not be required and the running overload curve would be joined with locked
rotor safe stall times to produce a single overload curve.
The generator manufacturer should provide a safe stall time or thermal limit curves
for any generator that is started as an induction motor. These thermal limits are
intended to be used as guidelines and their definition is not always precise. When
Setpoints
operation of the generator exceeds the thermal limit, the generator insulation does
not immediately melt, rather, the rate of insulation degradation reaches a point
where continued operation will significantly reduce generator life.
400
HIGH
300
INERTIA
MOTOR RUNNING OVERLOAD
200
C
B
20
A
G
10 F
8 E
6
4
E,F, AND G ARE THE
SAFE STALL THERMAL LIMIT
2 TIMES AT 100%, 90%, AND
80%VOLTAGE, REPECTIVELY
1
0 100 200 300 400 500 600 % CURRENT
806827A1.CDR
Setpoints
SELECT CURVE STYLE:
MESSAGE Dependent
Standard
The RTD BIAS MINIMUM, RTD BIAS CENTER, and RTD BIAS MAXIMUM setpoints is are seen
only if ENABLE RTD BIASING is set to “Yes”.
NOTE
The STANDARD OVERLOAD CURVE NUMBER is seen only if SELECT CURVE STYLE is set to
“Standard”. If the SELECT CURVE STYLE is set to “Voltage Dependent”, all setpoints
NOTE shown after the STANDARD OVERLOAD CURVE NUMBER are displayed. If the SELECT
CURVE STYLE is set to “Custom”, the setpoints shown after TIME TO TRIP AT 20.0 X FLA
are not displayed.
The current measured at the output CTs is used for the thermal model. The thermal
model consists of five key elements: the overload curve and overload pickup level,
the unbalance biasing of the generator current while the machine is running, the
cooling time constants, and the biasing of the thermal model based on hot/cold
generator information and measured stator temperature. Each of these elements
are described in detail in the sections that follow.
The generator FLA is calculated as:
Generator Rated MVA
NOTE --------------------------------------------------------------------------------------------------------------------------------- (EQ 5.29)
3 × Rated Generator Phase-Phase Voltage
The 489 integrates both stator and rotor heating into one model. Machine heating is
reflected in a register called Thermal Capacity Used. If the machine has been
stopped for a long period of time, it will be at ambient temperature and thermal
capacity used should be zero. If the machine is in overload, once the thermal
capacity used reaches 100%, a trip will occur.
The overload curve accounts for machine heating during stall, acceleration, and
running in both the stator and the rotor. The Overload Pickup setpoint defines where
the running overload curve begins as the generator enters an overload condition.
This is useful to accommodate a service factor. The curve is effectively cut off at
current values below this pickup.
Setpoints
Generator thermal limits consist of three distinct parts based on the three conditions
of operation, locked rotor or stall, acceleration, and running overload. Each of these
curves may be provided for both a hot and cold machine. A hot machine is defined
as one that has been running for a period of time at full load such that the stator
and rotor temperatures have settled at their rated temperature. A cold machine is
defined as a machine that has been stopped for a period of time such that the stator
and rotor temperatures have settled at ambient temperature. For most machines,
the distinct characteristics of the thermal limits are formed into one smooth
homogeneous curve. Sometimes only a safe stall time is provided. This is acceptable
if the machine has been designed conservatively and can easily perform its required
duty without infringing on the thermal limit. In this case, the protection can be
conservative. If the machine has been designed very close to its thermal limits when
operated as required, then the distinct characteristics of the thermal limits become
important.
The 489 overload curve can take one of three formats, Standard, Custom Curve, or
Voltage Dependent. Regardless of which curve style is selected, the 489 will retain
thermal memory in the form of a register called Thermal Capacity Used. This
register is updated every 50 ms using the following equation:
50 ms
TC used t = TC used t – 50ms + --------------------------------- × 100% (EQ 5.30)
time to trip
where time to trip = time taken from the overload curve at Ieq as a function of FLA.
The overload protection curve should always be set slightly lower than the thermal
limits provided by the manufacturer. This will ensure that the machine is tripped
before the thermal limit is reached. If the starting times are well within the safe stall
times, it is recommended that the 489 Standard Overload Curve be used. The
standard overload curves are a series of 15 curves with a common curve shape
based on typical generator thermal limit curves (see the following figure and table).
When the generator trips offline due to overload the generator will be locked out
(the trip relay will stay latched) until generator thermal capacity reaches 15%.
100000
10000
TIME IN SECONDS
1000
100
Setpoints
x15
10
x1
1.00
0.10 1.00 10 100 1000
6.00 2.50 5.00 7.49 9.99 12.49 14.99 17.49 19.99 22.48 24.98 27.48 29.98 32.48 34.97 37.47
6.50 2.12 4.24 6.36 8.48 10.60 12.72 14.84 16.96 19.08 21.20 23.32 25.44 27.55 29.67 31.79
7.00 1.82 3.64 5.46 7.29 9.11 10.93 12.75 14.57 16.39 18.21 20.04 21.86 23.68 25.50 27.32
7.50 1.58 3.16 4.75 6.33 7.91 9.49 11.08 12.66 14.24 15.82 17.41 18.99 20.57 22.15 23.74
8.00 1.39 2.78 4.16 5.55 6.94 8.33 9.71 11.10 12.49 13.88 15.27 16.65 18.04 19.43 20.82
10.00 1.39 2.78 4.16 5.55 6.94 8.33 9.71 11.10 12.49 13.88 15.27 16.65 18.04 19.43 20.82
15.00 1.39 2.78 4.16 5.55 6.94 8.33 9.71 11.10 12.49 13.88 15.27 16.65 18.04 19.43 20.82
20.00 1.39 2.78 4.16 5.55 6.94 8.33 9.71 11.10 12.49 13.88 15.27 16.65 18.04 19.43 20.82
489
GE Multilin TYPICAL CUSTOM CURVE
10000
1
TIME TO TRIP IN SECONDS
2
100
3
10
Setpoints
4
5
1.0
0.1
1
1000
10
100
0.5
489
THERMAL LIMITS
GE Multilin FOR HIGH INERTIAL LOAD
1000
900
800
700
1- Running Overload Thermal Limit
600 1
2- Acceleration Thermal Limit @ 80%V
500 3- Acceleration Thermal Limit @ 100%V
4- Locked Rotor Thermal Limit
400 5- Machine Acceleration Curve @ 80% V
6- Machine Acceleration Curve @ 100%V
300
Setpoints
2
200
100
90
80
TIME TO TRIP (SECONDS)
70
60
50
40
30
20
10
9
8
7
4
6
5
4
5
3
6
2
1
1 2 3 4 5 6 7 8
To illustrate the Voltage Dependent Overload Curve feature, the thermal limits
shown in Thermal Limits for High Inertial Load on page 5–62 will be used.
1. Construct a custom curve for the running overload thermal limit. If the curve
does not extend to the acceleration thermal limits, extend it such that the curve
intersects the acceleration thermal limit curves. (see the custom curve below).
489
VOLTAGE DEPENDENT OVERLOAD
GE Multilin (CUSTOM CURVE)
1000
900
800
700
600
500
400
300
Acceleration Intersect at 80%V
200
70
60
50
40
Setpoints
30
20
10
9
8
7
6
5
1
1 2 3 4 5 6 7 8
2. Enter the per unit current value for the acceleration overload curve intersect
with the custom curve for 80% voltage. Also enter the per unit current and safe
stall protection time for 80% voltage (see the acceleration curves below).
3. Enter the per unit current value for the acceleration overload curve intersect
with the custom curve for 100% voltage. Also enter the per unit current and
safe stall protection time for 100% voltage (see the acceleration curves below).
489
VOLTAGE DEPENDENT OVERLOAD
GE Multilin (ACCELERATION CURVES)
1000
900
800
700
600
500
489 Custom Curve
400
300
200
100
90
80
TIME TO TRIP (SECONDS)
70
60
50
Setpoints
40
30
20
10
9
8
7
6
5
1
1 2 3 4 5 6 7 8
MULTIPLES OF FULL LOAD AMPS
808828A3.CDR
The 489 takes the information provided and create protection curves for any voltage
between the minimum and 100%. For values above the voltage in question, the 489
extrapolates the safe stall protection curve to 110% voltage. This current level is
calculated by taking the locked rotor current at 100% voltage and multiplying by
1.10. For trip times above the 110% voltage level, the trip time of 110% will be
used (see the figure below).
489
VOLTAGE DEPENDENT
GE Multilin OVERLOAD PROTECTION CURVES
1000
900
800
700
600
Custom Curve
500
400
300
Acceleration Intersect at 80%V
200
60
50
40
Setpoints
30
1
1 2 3 4 5 6 7 8
MULTIPLES OF FULL LOAD AMPS 808831A3.CDR
The following curves illustrate the resultant overload protection for 80% and 100%
voltage, respectively. For voltages between these levels, the 489 shifts the
acceleration curve linearly and constantly based upon the measured voltage during
generator start.
489
VOLTAGE DEPENDENT
GE Multilin OVERLOAD PROTECTION at 80% V
1000
900
800
700
600
500
400
300
200
100
90
80
70
TIME TO TRIP (SECONDS)
60
50
40
30
Setpoints
20
10
9
8
7
6
5
1
1 2 3 4 5 6 7 8
MULTIPLES OF FULL LOAD AMPS 808830A3.CDR
489
VOLTAGE DEPENDENT
GE Multilin OVERLOAD PROTECTION at 100% V
1000
900
800
700
600
500
400
300
200
100
90
80
TIME TO TRIP (SECONDS)
70
60
50
40
30
20
Setpoints
10
9
8
7
6
5
1
1 2 3 4 5 6 7 8
d) Unbalance Bias
Unbalanced phase currents will cause additional rotor heating that will not be
accounted for by electromechanical relays and may not be accounted for in some
electronic protective relays. When the generator is running, the rotor will rotate in
the direction of the positive sequence current at near synchronous speed. Negative
sequence current, which has a phase rotation that is opposite to the positive
sequence current, and hence, opposite to the rotor rotation, will generate a rotor
voltage that will produce a substantial rotor current. This induced current will have a
frequency that is approximately twice the line frequency, 100 Hz for a 50 Hz system
or 120 Hz for a 60 Hz system. Skin effect in the rotor bars at this frequency will
cause a significant increase in rotor resistance and therefore, a significant increase
in rotor heating. This extra heating is not accounted for in the thermal limit curves
supplied by the generator manufacturer as these curves assume positive sequence
currents only that come from a perfectly balanced supply and generator design.
The 489 measures the ratio of negative to positive sequence current. The thermal
model may be biased to reflect the additional heating that is caused by negative
sequence current when the machine is running. This biasing is done by creating an
equivalent heating current rather than simply using average current (Iper_unit). This
equivalent current is calculated using the equation shown below.
2 2
I eq = I 1 + kI 2 (EQ 5.32)
where: Ieq = equivalent motor heating current in per unit (based on FLA)
I2= negative-sequence current in per unit (based on FLA)
I1= positive-sequence current in per unit (based on FLA)
k = constant relating negative-sequence rotor resistance to positive-
sequence rotor resistance, not to be confused with the k indicating
generator negative-sequence capability for an inverse time curve.
The figure below shows induction machine derating as a function of voltage
unbalance as recommended by NEMA (National Electrical Manufacturers
Association). Assuming a typical inrush of 6 × FLA and a negative sequence
impedance of 0.167, voltage unbalances of 1, 2, 3, 4, and 5% equal current
unbalances of 6, 12, 18, 24, and 30%, respectively. Based on this assumption, the
GE curve illustrates the amount of machine derating for different values of k entered
for the UNBALANCE BIAS K FACTOR setpoint. Note that the curve created when k = 8 is
almost identical to the NEMA derating curve.
1.05 1.05
1.00 1.00
DERATING FACTOR
DERATING FACTOR
Setpoints
0.95 0.95
k= 2
0.90 0.90
0.85 0.85 k= 4
0.80 0.80 k= 6
k= 8
0.75 0.75
k= 10
0.70 0.70
0 1 2 3 4 5 0 1 2 3 4 5
NEMA GE MULTILIN
808728A1.CDR
If a k value of 0 is entered, the unbalance biasing is defeated and the overload curve
will time out against the measured per unit motor current. k may be calculated
conservatively as:
175 230
k = ----------- (typical estimate); k = ----------- (conservative estimate) (EQ 5.33)
2 2
I LR I LR
e) Machine Cooling
The 489 thermal capacity used value is reduced exponentially when the motor
current is below the OVERLOAD PICKUP setpoint. This reduction simulates machine
cooling. The cooling time constants should be entered for both stopped and running
cases (the generator is assumed to be running if current is measured or the
generator is online). A machine with a stopped rotor normally cools significantly
slower than one with a turning rotor. Machine cooling is calculated using the
following formulae:
–t ⁄ τ
TC used = ( TC used_start – TC used_end ) ( e ) + TC used_end (EQ 5.34)
I eq hot
TC used_end = ⎛ -------------------------------------------------⎞ ⎛ 1 – ------------⎞ × 100% (EQ 5.35)
⎝ overload_pickup⎠ ⎝ cold⎠
100 100
75 75
25 25
0 0
0 30 60 90 120 150 180 0 30 60 90 120 150 180
Time in Minutes Time in Minutes
100 100
Setpoints
75 75
Thermal Capacity Used
25 25
0 0
0 30 60 90 120 150 180 0 30 60 90 120 150 180
Time in Minutes Time in Minutes
hot
TC used_end = I eq × ⎛ 1 – ------------⎞ × 100% (EQ 5.36)
⎝ cold⎠
g) RTD Bias
The thermal replica created by the features described in the sections above operates
as a complete and independent model. However, the thermal overload curves are
based solely on measured current, assuming a normal 40°C ambient and normal
machine cooling. If there is an unusually high ambient temperature, or if machine
cooling is blocked, generator temperature will increase. If the stator has embedded
RTDs, the 489 RTD bias feature should be used to correct the thermal model.
The RTD bias feature is a two part curve, constructed using 3 points. If the
maximum stator RTD temperature is below the RTD BIAS MINIMUM setpoint (typically
40°C), no biasing occurs. If the maximum stator RTD temperature is above the RTD
BIAS MAXIMUM setpoint (typically at the stator insulation rating or slightly higher),
then the thermal memory is fully biased and thermal capacity is forced to 100%
used. At values in between, the present thermal capacity used created by the
overload curve and other elements of the thermal model, is compared to the RTD
Bias thermal capacity used from the RTD Bias curve. If the RTD Bias thermal
capacity used value is higher, then that value is used from that point onward. The
RTD BIAS CENTER POINT should be set at the rated running temperature of the
machine. The 489 automatically determines the thermal capacity used value for the
center point using the HOT/COLD SAFE STALL RATIO setpoint.
hot
TC used at RBC = ⎛ 1 – ------------⎞ × 100%
Setpoints
(EQ 5.37)
⎝ cold⎠
NOTE
Hot/Cold = 0.85
60
40
20
RTD Bias Center Point
RTD Bias Minimum
0
–50 0 50 100 150 200 250
Maximum Stator RTD Temperature
808721A1.CDR
Setpoints
THERMAL MODEL Range: On, Off
MESSAGE
ALARM EVENTS: Off
Once the thermal model is setup, an alarm and/or trip element can be enabled. If
the generator has been offline for a long period of time, it will be at ambient
temperature and thermal capacity used should be zero. If the generator is in
overload, once the thermal capacity used reaches 100%, a trip will occur. The
thermal model trip will remain active until a lockout time has expired. The lockout
time will be based on the reduction of thermal capacity from 100% used to 15%
used. This reduction will occur at a rate defined by the offline cooling time constant.
The thermal capacity used alarm may be used as a warning indication of an
impending overload trip.
S10 Monitoring
Trip Counter PATH: SETPOINTS ZV S10 MONITORING Z TRIP COUNTER
When enabled, a trip counter alarm will occur when the TRIP COUNTER ALARM LEVEL is
reached. The trip counter must be cleared or the alarm level raised and the reset
key must be pressed (if the alarm was latched) to reset the alarm.
For example, it might be useful to set a Trip Counter alarm at 100 trips, prompting
the operator or supervisor to investigate the type of trips that have occurred. A
breakdown of trips by type may be found in the A4 MAINTENANCE ZV TRIP COUNTERS
actual values page. If a trend is detected, it would warrant further investigation.
If the breaker failure alarm feature may be enabled as latched or unlatched. If the
1 Trip output relay is operated and the generator current measured at any of the
three output CTs is above the level programmed for the period of time specified by
the delay, a breaker failure alarm will occur. The time delay should be slightly longer
than the breaker clearing time.
Trip Coil Monitor PATH: SETPOINTS ZV S10 MONITORING ZV TRIP COIL MONITOR
If the trip coil monitor alarm feature is enabled as latched or unlatched, the trip coil
supervision circuitry will monitor the trip coil circuit for continuity any time that the
breaker status input indicates that the breaker is closed. If that continuity is broken,
a trip coil monitor alarm will occur in approximately 300 ms.
If 52 Open/Closed is selected, the trip coil supervision circuitry monitors the trip coil
circuit for continuity at all times regardless of breaker state. This requires an
alternate path around the 52a contacts in series with the trip coil when the breaker
is open. See the figure below for modifications to the wiring and proper resistor
selection. If that continuity is broken, a Starter Failure alarm will indicate Trip Coil
Supervision.
52a
TRIP COIL 52a 52a
OPEN/CLOSED
TRIP SUPERVISION
COIL "52 Open/Closed"
TRIP TRIP
COIL COIL
WITH MULTIPLE
BREAKER AUX
TRIP COIL CLOSED SUPERVISION CONTACTS
"52 Closed"
52a TRIP COIL OPEN/CLOSED SUPERVISION
"52 Open/Closed"
Setpoints
48 VDC 10 K 2
125 VDC 25 K 5
808727A1.CDR 250 VDC 50 K 5
A fuse failure is detected when there are significant levels of negative sequence
voltage without corresponding levels of negative sequence current measured at the
output CTs. Also, if the generator is online and there is not significant positive
sequence voltage, it could indicate that all VT fuses have been pulled or the VTs are
racked out. If the alarm is enabled and a VT fuse failure detected, elements that
could nuisance operation are blocked and an alarm occurs. These blocked elements
include voltage restraint for the phase overcurrent, undervoltage, phase reversal,
and all power elements.
I2 / I1 < 20%
V2 / V1 > 25% 99ms
I1 > 0.075 x CT AND
0 Block
V1 > 0.05 x Full Scale Appropriate
Breaker Status = Online Elements
OR &
Operate
Alarm
99ms Relay
AND
V1 < 0.05 × Full Scale 0
Setpoints
Mvar Mvar DEMAND Range: 5 to 90 min. in steps of 1
DEMAND [Z] PERIOD: 15 min.
The 489 can measure the demand of the generator for several parameters (current,
MW, Mvar, MVA). The demand values of generators may be of interest for energy
management programs where processes may be altered or scheduled to reduce
overall demand on a feeder. The generator FLA is calculated as:
N
1
Demand = ----
N ∑ Average N (EQ 5.41)
n=1
160
140
120
MAGNITUDE
100
80
60
40
Setpoints
20
0
t=0 t+10 t+20 t+30 t+40 t+50 t+60 t+70 t+80 t+90 t+100
TIME 808717A1.CDR
The 489 can perform pulsed output of positive kWh and both positive and negative
kvarh. Each output parameter can be assigned to any one of the alarm or auxiliary
relays. Pulsed output is disabled for a parameter if the relay setpoint is selected as
OFF for that pulsed output. The minimum time between pulses is fixed to 400
milliseconds.
This feature should be programmed so that no more than one pulse per 600
milliseconds is required or the pulsing will lag behind the interval activation. Do not
NOTE assign pulsed outputs to the same relays as alarms and trip functions.
PULSE
WIDTH
808738A1.CDR
Running Hour Setup PATH: SETPOINTS ZV S10 MONITORING ZV RUNNING HOUR SETUP
Setpoints
The 489 can measure the generator running hours. This value may be of interest for
periodic maintenance of the generator. The initial generator running hour allows the
user to program existing accumulated running hours on a particular generator the
relay is protecting. This feature switching 489 relays without losing previous
generator running hour values.
Setpoints
Apparent Power 0.00 to 2.00 × Rated 0.01 0.00 1.25
Analog Inputs 1 to 4 –50000 to +50000 1 0 50000
Tachometer 0 to 7200 RPM 1 3500 3700
Thermal Capacity 0 to 100% 1 0 100
Used
Current Demand 0.00 to 20.00 × FLA 0.01 0.00 1.25
Mvar Demand 0.00 to 2.00 × Rated 0.01 0.00 1.25
MW Demand 0.00 to 2.00 × Rated 0.01 0.00 1.25
MVA Demand 0.00 to 2.00 × Rated 0.01 0.00 1.25
Analog Inputs 1 to 4 PATH: SETPOINTS ZV S11 ANALOG I/O ZV ANALOG INPUT 1(4)
There are 4 analog inputs (4 to 20 mA, 0 to 20 mA, or 0 to 1 mA) that may be used
to monitor transducers such as vibration monitors, tachometers, pressure
Setpoints
transducers, etc. These inputs may be used for alarm and/or tripping purposes. The
inputs are sampled every 50 ms. The level of the analog input is also available over
the communications port. With the EnerVista 489 Setup program, the level of the
transducer may be trended and graphed.
Before the input may be used, it must be configured. A name may be assigned for
the input, units may be assigned, and a minimum and maxi-mum value must be
assigned. Also, the trip and alarm features may be blocked until the generator is
online for a specified time delay. If the block time is 0 seconds, there is no block and
the trip and alarm features will be active when the generator is offline or online. If a
time is programmed other than 0 seconds, the feature will be disabled when the
generator is offline and also from the time the machine is placed online until the
time entered expires. Once the input is setup, both the trip and alarm features may
be configured. In addition to programming a level and time delay, the PICKUP
setpoint may be used to dictate whether the feature picks up when the measured
value is over or under the level.
If a vibration transducer is to be used, program the name as “Vib Monitor”, the units
as “mm/s”, the minimum as “0”, the maximum as “25”, and the Block From Online
as “0 s”. Set the alarm for a reasonable level slightly higher than the normal
vibration level. Program a delay of “3 s” and the pickup as “Over”.
S12 Testing
Simulation Mode PATH: SETPOINTS ZV S12 489 TESTING Z SIMULATION MODE
The 489 may be placed in several simulation modes. This simulation may be useful
for several purposes. First, it may be used to under-stand the operation of the 489
for learning or training purposes. Second, simulation may be used during startup to
verify that control circuitry operates as it should in the event of a trip or alarm. In
addition, simulation may be used to verify that setpoints had been set properly in
the event of fault conditions.
The SIMULATION MODE setpoint may be entered only if the generator is offline, no
current is measured, and there are no trips or alarms active. The values entered as
Pre-Fault Values will be substituted for the measured values in the 489 when the
SIMULATION MODE is “Simulate Pre-Fault”. The values entered as Fault Values will be
substituted for the measured values in the 489 when the SIMULATION MODE is
“Simulate Fault”. If the SIMULATION MODE is set to “Pre-Fault to Fault”, the Pre-Fault
values will be substituted for the period of time specified by the delay, followed by
the Fault values. If a trip occurs, the SIMULATION MODE reverts to “Off”. Selecting
“Off” for the SIMULATION MODE places the 489 back in service. If the 489 measures
current or control power is cycled, the SIMULATION MODE automatically reverts to
“Off”.
Setpoints
If the 489 is to be used for training, it might be desirable to allow all parameter
averages, statistical information, and event recording to update when operating in
simulation mode. If however, the 489 has been installed and will remain installed on
a specific generator, it might be desirable assign a digital input to Test Input and to
short that input to prevent all of this data from being corrupted or updated. In any
event, when in simulation mode, the 489 In Service LED (indicator) will flash,
indicating that the 489 is not in protection mode.
The values entered under Pre-Fault Values will be substituted for the measured
values in the 489 when the SIMULATION MODE is “Simulate Pre-Fault”.
Setpoints
FAULT SYSTEM Range: 5.0 to 90.0 Hz in steps of 0.1
MESSAGE
FREQUENCY: 60.0 Hz
The values entered here are substituted for the measured values in the 489 when
the SIMULATION MODE is “Simulate Fault”.
Test Output Relays PATH: SETPOINTS ZV S12 489 TESTING ZV TEST OUTPUT RELAYS
The test output relays setpoint may be used during startup or testing to verify that
the output relays are functioning correctly. The output relays can be forced to
operate only if the generator is offline, no current is measured, and there are no
trips or alarms active. If any relay is forced to operate, the relay will toggle from its
normal state. The appropriate relay indicator will illuminate at that time. Selecting
“Disabled” places the output relays back in service. If the 489 measures current or
control power is cycled, the force operation of relays setpoint will automatically
become disabled and the output relays will revert back to their normal states.
If any relay is forced, the 489 In Service indicator will flash, indicating that the 489
is not in protection mode.
Test Analog Output PATH: SETPOINTS ZV S12 489 TESTING ZV TEST ANALOG OUTPUT
These setpoints may be used during startup or testing to verify that the analog
outputs are functioning correctly. The analog outputs can be forced only if the
generator is offline, no current is measured, and there are no trips or alarms active.
When the FORCE ANALOG OUTPUTS FUNCTION is “Enabled”, the output reflects the
forced value as a percentage of the range 4 to 20 mA or 0 to 1 mA. Selecting
“Disabled” places all four analog output channels back in service, reflecting their
programmed parameters. If the 489 measures current or control power is cycled,
the force analog output function is automatically disabled and all analog outputs will
revert back to their normal state.
Any time the analog outputs are forced, the In Service indicator will flash, indicating
that the 489 is not in protection mode.
Comm Port Monitor PATH: SETPOINTS ZV S12 489 TESTING ZV COMMUNICATION PORT MONITOR
Setpoints
appears in the Tx1 and Tx2 buffers. In addition to these buffers, there is a message
indicating the status of the last received message.
This section is for use by GE Multilin personnel for testing and calibration purposes.
6 Actual Values
Overview
Actual Values Main The actual values message map is shown below.
Menu
ACTUAL
VALUES [Z] NETWORK STATUS [Z] See page 6–3.
MESSAGE GENERATOR [Z] See page 6–3.
LAST
MESSAGE TRIP [Z] See page 6–4.
ALARM
MESSAGE See page 6–5.
Actual Values
STATUS [Z]
TRIP
MESSAGE PICKUPS [Z] See page 6–8.
ALARM
MESSAGE PICKUPS [Z] See page 6–10.
MESSAGE DIGITAL [Z] See page 6–13.
REAL
MESSAGE TIME [Z] See page 6–13.
END OF PAGE
MESSAGE
ACTUAL
VALUES [Z] CURRENT [Z] See page 6–14.
MESSAGE VOLTAGE [Z] See page 6–15.
MESSAGE POWER [Z] See page 6–16.
MESSAGE TEMPERATURE [Z] See page 6–16.
MESSAGE DEMAND [Z] See page 6–17.
MESSAGE ANALOG [Z] See page 6–17.
MESSAGE SPEED [Z] See page 6–18.
END OF PAGE
MESSAGE
ACTUAL
VALUES [Z] PARAMETER [Z] See page 6–18.
MESSAGE RTD [Z] See page 6–18.
ANALOG
MESSAGE INPUT [Z] See page 6–19.
END OF PAGE
MESSAGE
ACTUAL
VALUES [Z] TRIP [Z] See page 6–20.
MESSAGE
Actual Values
MESSAGE TIMERS [Z] See page 6–22.
END OF PAGE
MESSAGE
ACTUAL
VALUES [Z] E255 [Z] See page 6–23.
MESSAGE E254 [Z] See page 6–23.
MESSAGE E000 [Z] See page 6–23.
END OF PAGE
MESSAGE
ACTUAL 489
VALUES [Z] MODEL [Z] See page 6–25.
MESSAGE CALIBRATION [Z] See page 6–25.
END OF PAGE
MESSAGE
Description Measured values, maintenance and fault analysis information are accessed in the
actual values. Actual values may be accessed via one of the following methods:
1. Front panel, using the keys and display.
2. Front program port and a portable computer running the EnerVista 489 Setup
software supplied with the relay.
3. Rear terminal RS485 port and a PLC/SCADA system running user-written
software.
Any of these methods can be used to view the same information. However, a
computer makes viewing much more convenient since many variables may be
viewed simultaneously.
Actual value messages are organized into logical groups, or pages, for easy
reference, as shown below. All actual value messages are illustrated and described
in blocks throughout this chapter. All values shown in these message illustrations
assume that no inputs (besides control power) are connected to the 489.
In addition to the actual values, there are also diagnostic and flash messages that
appear only when certain conditions occur. They are described later in this chapter.
A1 Status
Network Status PATH: ACTUAL VALUES Z A1 STATUS ZV NETWORK STATUS
Actual Values
NETWORK Ethernet Lnk Con Dia Range: see description below
STATUS [Z] Status [] [] [
This actual value appears when the relay is ordered with the Ethernet (T) option.
The ETHERNET STATUS actual value message indicates the status of the Ethernet link,
connection, and diagnostic via three indicators. The [] symbol indicates on, and
the [ ] symbol indicates off. There is also a blinking indication.
The box under LNK column indicates the Ethernet link status. If it is on, the Ethernet
port is connected to the network; if it is off, the port is disconnected. This indicator
is normally on.
The box under the CON column indicates the connection status. If on, the Ethernet
port is configured and ready to transmit and receive data. If blinking, the Ethernet
port is either active (transmitting or receiving data) or indicating an error if the
diagnostic status is also on or blinking.
The box under the DIA column indicates the diagnostic status. If it is on, then either
a fatal Ethernet port error has occurred or there is a duplicate IP address on the
network. If blinking, then there is a non-fatal network error. Off indicates no errors.
These messages describe the status of the generator at any given point in time. If
the generator has been tripped, is still offline, and the 489 has not yet been reset,
the GENERATOR STATUS will be “Tripped”. The GENERATOR THERMAL CAPACITY USED
value reflects an integrated value of both the stator and rotor thermal capacity
used. The values for ESTIMATED TRIP TIME ON OVERLOAD will appear whenever the 489
thermal model picks up on the overload curve.
Last Trip Data PATH: ACTUAL VALUES Z A1 STATUS ZV LAST TRIP DATA
PRETRIP: 0% FLA
The range for the CAUSE OF LAST TRIP setpoint is: No Trip to Date, General Inputs A to
G, Sequential Trip, Field-Bkr Discrep., Tachometer, Thermal Model, Offline
NOTE Overcurrent, Phase Overcurrent, Neg. Seq. Overcurrent, Ground Overcurrent, Phase
Differential, RTDs 1 to 12, Overvoltage, Undervoltage, Volts/Hertz, Phase Reversal,
Underfrequency, Overfrequency, Neutral O/V, Neutral U/V (3rd), Reactive Power,
Reverse Power, Low Forward Power, Inadvertent Energ., and Analog Inputs 1 to 4.
Immediately prior to issuing a trip, the 489 takes a snapshot of generator
parameters and stores them as pre-trip values; this allows for troubleshooting after
the trip occurs. The cause of last trip message is updated with the current trip and
the screen defaults to that message. All trip features are automatically logged as
Actual Values
date and time stamped events as they occur. This information can be cleared using
the S1 489 SETUP ZV CLEAR DATA ZV CLEAR LAST TRIP DATA setpoint. If the cause of last
trip is “No Trip To Date”, the subsequent pretrip messages will not appear. Last Trip
Data will not update if a digital input programmed as Test Input is shorted.
Actual Values
MW DEMAND
MESSAGE
ALARM: 50.500
Actual Values
DISTANCE ZONE 2
MESSAGE Out, Active Trip, Latched Trip.
PICKUP: Not Enabled
The various trip pickup actual values reflect the Input Name as programmed in the
first line of the message. The various digital and analog input functions are shown
NOTE only if the function has been assigned as an input.
The trip pickup messages may be very useful during testing. They will indicate if a
trip feature has been enabled, if it is inactive (not picked up), timing out (picked up
Actual Values
and timing), active trip (still picked up, timed out, and causing a trip), or latched tip
(no longer picked up, but had timed out and caused a trip that is latched). These
values may also be particularly useful as data transmitted to a master device for
monitoring.
Actual Values
REVERSE POWER
MESSAGE Out, Active Alarm, Latched Alarm.
PICKUP: Not Enabled
Mvar DEMAND
MESSAGE Out, Active Alarm, Latched Alarm.
PICKUP: Not Enabled
The various alarm pickup actual values reflect the Input Name as programmed in
the first line of the message. The various digital and analog input functions are
NOTE shown only if the function has been assigned as an input.
The alarm pickup messages may be very useful during testing. They will indicate if a
alarm feature has been enabled, if it is inactive (not picked up), timing out (picked
up and timing), active alarm (still picked up, timed out, and causing an alarm), or
latched alarm (no longer picked up, but had timed out and caused a alarm that is
latched). These values may also be particularly useful as data transmitted to a
master device for monitoring.
The messages shown here may be used to monitor digital input status. This may be
Actual Values
useful during relay testing or during installation.
Real Time Clock PATH: ACTUAL VALUES Z A1 STATUS ZV REAL TIME CLOCK
The time and date from the 489 real time clock may be viewed here.
A2 Metering Data
Current Metering PATH: ACTUAL VALUES ZV A2 METERING DATA Z CURRENT METERING
A: 0 B: 0 Range: 0 to 999999 A
CURRENT [Z] C: 0 Amps
a: 0 b: 0 Range: 0 to 999999 A
MESSAGE
c: 0 Neut.Amps
a: 0 b: 0 Range: 0 to 999999 A
MESSAGE
c: 0 Diff.Amps
All measured current values are displayed here. A, B, C AMPS represent the output
side CT measurements: A, B, C NEUT. AMPS the neutral end CT measurements, and A,
B, C DIFF. AMPS the differential operating current calculated as the vector difference
between the output side and the neutral end CT measurements on a per phase
basis. The 489 negative-sequence current is defined as the ratio of negative-
sequence current to generator rated FLA, I2 / FLA × 100%. The generator full load
amps is calculated as: generator rated MVA / ( 3 × generator phase-to-phase
voltage). Polar coordinates for measured currents are also shown using Va (wye
connection) or Vab (open delta connection) as a zero angle reference vector. In the
absence of a voltage signal (Va or Vab), the IA output current is used as the zero
angle reference vector.
Actual Values
FREQUENCY: Range: 0.00 to 90.00 Hz. Not seen if VT
MESSAGE CONNECTION is “None”.
0.00 Hz
The values for power metering appear here. Three-phase total power quantities are
displayed here. Watthours and varhours are also shown here. Watthours and
varhours will not update if a digital input programmed as Test Input is shorted.
An induction generator, by convention generates Watts and consumes vars
(+W and –vars). A synchronous generator can also generate vars (+vars).
NOTE
If the VT CONNECTION TYPE is programmed as “None”, the THIS FEATURE NOT
PROGRAMMED flash message will appear when an attempt is made to enter this
group of messages.
These messages are seen only if the corresponding RTDs are programmed. The
actual messages reflect the RTD Names as programmed.
NOTE
The current level of the 12 RTDs will be displayed here. If the RTD is not connected,
the value will be “No RTD”. If the RTD is shorted, then “---” will be displayed. If no
RTDs are programmed in the S7 RTD TEMPERATURE setpoints menu, the THIS
FEATURE NOT PROGRAMMED flash message will appear when an attempt is made
to enter this group of messages.
Range: 0 to 999999 A
CURRENT
DEMAND [Z]
DEMAND: 0 Amps
METERING
Actual Values
PEAK Mvar DEMAND: Range: 0 to 2000.000 Mvar. Not seen if
MESSAGE VT CONNECTION TYPE is None
0.000 Mvar
The values for current and power demand are shown here. This peak demand
information can be cleared using the S1 489 SETUP ZV CLEAR DATA ZV CLEAR PEAK
DEMAND setpoint. Demand is shown only for positive real and positive reactive
power (+Watts, +vars). Peak demand will not update if a digital input programmed
as Test Input is shorted.
These messages are seen only if the corresponding Analog Inputs are programmed.
The actual messages reflect the Analog Input Names as programmed.
NOTE
The values for analog inputs are shown here. The name of the input and the units
will reflect those programmed for each input. If no analog inputs are programmed in
the S11 ANALOG I/O setpoints page, the THIS FEATURE NOT PROGRAMMED flash
message will appear when an attempt is made to enter this group of messages.
If the Tachometer function is assigned to one of the digital inputs, its speed be
viewed here. If no digital input is configured for tachometer, the THIS FEATURE
NOT PROGRAMMED flash message will appear when an attempt is made to enter
this group of messages.
A3 Learned Data
Parameter Averages PATH: ACTUAL VALUES ZV A3 LEARNED DATA Z PARAMETER AVERAGES
The 489 calculates the average magnitude of several parameters over a period of
Actual Values
These messages are seen only if the corresponding RTDs are programmed. The
actual messages reflect the RTD Names as programmed.
NOTE
The 489 will learn the maximum temperature for each RTD. This information can be
cleared using the S1 489 SETUP ZV CLEAR DATA ZV CLEAR RTD MAXIMUMS setpoint. The
RTD maximums will not update if a digital input programmed as Test Input is
shorted. If no RTDs are programmed in the S7 RTD TEMPERATURE setpoints page, the
THIS FEATURE NOT PROGRAMMED flash message will appear when an attempt is
made to enter this group of messages.
Analog Input Min/Max PATH: ACTUAL VALUES ZV A3 LEARNED DATA ZV ANALOG INPUT MIN/MAX
Actual Values
MIN: O Units
These messages are seen only if the corresponding Analog Inputs are programmed.
The actual messages reflect the Analog Input Names as programmed.
NOTE
The 489 learns the minimum and maximum values of the analog inputs since they
were last cleared. This information can be cleared using the S1 489 SETUP ZV CLEAR
DATA ZV CLEAR ANALOG I/P MIN/MAX setpoint. When the data is cleared, the present
value of each analog input will be loaded as a starting point for both minimum and
maximum. The name of the input and the units will reflect those programmed for
each input. Analog Input minimums and maximums will not update if a digital input
programmed as Test Input is shorted.
If no Analog Inputs are programmed in the S11 ANALOG I/O setpoints menu, the THIS
FEATURE NOT PROGRAMMED flash message will appear when an attempt is made
to enter this group of messages.
A4 Maintenance
Trip Counters PATH: ACTUAL VALUES ZV A4 MAINTENANCE Z TRIP COUNTERS
Range: 0 to 50000
Actual Values
PHASE DIFFERENTIAL
MESSAGE
TRIPS: 0
Range: 0 to 50000
Actual Values
INADVERTENT ENERG.
MESSAGE
TRIPS: 0
The number of trips by type is displayed here. When the total reaches 50000, all
counters reset. This information can be cleared with the S1 489 SETUP ZV CLEAR DATA
ZV CLEAR TRIP COUNTERS setpoint. Trip counters will not update if a digital input
programmed as Test Input is shorted. In the event of multiple trips, the only the
first trip will increment the trip counters.
Range: 0 to 50000
NUMBER OF BREAKER
GENERAL [Z]
OPERATIONS: 0
COUNTERS
One of the 489 general counters will count the number of breaker operations over
time. This may be useful information for breaker maintenance. The number of
breaker operations is incremented whenever the breaker status changes from
closed to open and all phase currents are zero. Another counter counts the number
of thermal resets if one of the assignable digital inputs is assigned to thermal reset.
This may be useful information when troubleshooting. When either of these
counters exceeds 50000, that counter will reset to 0.
The NUMBER OF BREAKER OPERATIONS counter can also be cleared using the S1 489
SETUP ZV CLEAR DATA ZV CLEAR BREAKER INFORMATION setpoint. The NUMBER OF
THERMAL RESETS counter can be cleared using the S1 489 SETUP ZV CLEAR DATA ZV
CLEAR GENERATOR INFORMATION setpoint.
The number of breaker operations will not update if a digital input programmed as
Test Input is shorted.
The 489 accumulates the total online time for the generator. This may be useful for
scheduling routine maintenance. When this timer exceeds 1000000, it resets to 0.
This timer can be cleared using the S1 489 SETUP ZV CLEAR DATA ZV CLEAR GENERATOR
INFORMATION setpoint. The generator hours online will not update if a digital input
programmed as Test Input is shorted.
Actual Values
A5 Event Recorder
Event Recorder PATH: ACTUAL VALUES ZV A5 EVENT RECORDER ZV E001(E256)
ACTIVE Range: 1, 2
MESSAGE
GROUP E001: 1
A: 0 B: 0 Range: 0 to 999999 A
MESSAGE
C: 0 A E001
Actual Values
E001: 0.0 V there is a neutral VT.
The 489 Event Recorder stores generator and system information each time an
event occurs. The description of the event is stored and a time and date stamp is
also added to the record.
The event recorder data may be inaccurate if 489 relay power-on time is less than
2 seconds.
NOTE
The date and time stamping feature allows reconstruction of the sequence of events
for troubleshooting. Events include all trips, any alarm optionally (except Service
Alarm, and 489 Not Inserted Alarm, which always records as events), loss of control
power, application of control power, thermal resets, simulation, serial
communication starts/stops, and general input control functions optionally.
E001 is the most recent event and E256 is the oldest event. Each new event bumps
the other event records down until the 256th event is reached. The 256th event
record is lost when the next event occurs. This information can be cleared using S1
489 SETUP ZV CLEAR DATA ZV CLEAR EVENT RECORD setpoint. The event record will not
update if a digital input programmed as Test Input is shorted.
Loss of Excitation 2 Low Fwd Power Trip Neg Seq O/C Trip Neutral O/V Trip
Neut. U/V (3rd) Trip Offline O/C Trip Overfrequency Trip Overvoltage Trip
Phase O/C Trip Phase Reversal Trip Reactive Power Trip Reverse Power Trip
RTD11 Trip * Sequential Trip Stator RTD 1 Trip * Stator RTD 2 Trip *
Stator RTD 3 Trip * Stator RTD 4 Trip * Stator RTD 5 Trip * Stator RTD 6 Trip *
Tachometer Trip Thermal Model Trip Underfrequency Trip Undervoltage Trip
Volts/Hertz Trip
A6 Product Information
489 Model Info PATH: ACTUAL VALUES ZV A6 PRODUCT INFO Z 489 MODEL INFO
All of the 489 model information may be viewed here when the unit is powered up.
In the event of a product software upgrade or service question, the information
shown here should be jotted down prior to any inquiry.
Actual Values
CALIBRATION [Z]
DATE: Jan 01 1996
INFORMATION
The date of the original calibration and last calibration may be viewed here.
Diagnostics
Diagnostic Messages In the event of a trip or alarm, some of the actual value messages are very helpful
in diagnosing the cause of the condition. The 489 will automatically default to the
most important message. The hierarchy is trip and pretrip messages, then alarm
messages. In order to simplify things for the operator, the Message LED (indicator)
will flash prompting the operator to press the MESSAGE X key. When the MESSAGE X
key is pressed, the 489 will automatically display the next relevant message and
continue to cycle through the messages with each keypress. When all of these
conditions have cleared, the 489 will revert back to the normal default messages.
Any time the 489 is not displaying the default messages because other actual value
or setpoint messages are being viewed and there are no trips or alarms, the
Message LED (indicator) will be on solid. From any point in the message structure,
pressing the MESSAGE X key will cause the 489 to revert back to the normal default
messages. When normal default messages are being displayed, pressing the
MESSAGE X key will cause the 489 to display the next default message immediately.
EXAMPLE:
If a thermal model trip occurred, an RTD alarm may also occur as a result of the
overload. The 489 would automatically default to the CAUSE OF LAST TRIP message at
the top of the A1 STATUS ZV LAST TRIP DATA queue and the Message LED would flash.
Pressing the MESSAGE X key cycles through the time and date stamp information as
well as all of the pre-trip data. When the bottom of this queue is reached, an
additional press of the MESSAGE X key would normally return to the top of the queue.
However, because there is an alarm active, the display will skip to the alarm
message at the top of the A1 STATUS ZV ALARM STATUS queue. Finally, another press
of the MESSAGE X key will cause the 489 to return to the original CAUSE OF LAST TRIP
message, and the cycle could be repeated.
↓
↓
↓
ANALOG INPUT 4
PreTrip: 0 Units
When the RESET has been pressed and the hot RTD condition is no longer present,
Actual Values
Flash Messages Flash messages are warning, error, or general information messages that are
temporarily displayed in response to certain key presses. These messages are
intended to assist with navigation of the 489 messages by explaining what has
happened or by prompting the user to perform certain actions.
DATA CLEARED DATE ENTRY DATE ENTRY WAS DEFAULT MESSAGE DEFAULT MESSAGE
SUCCESSFULLY OUT OF RANGE NOT COMPLETE HAS BEEN ADDED HAS BEEN REMOVED
DEFAULT MESSAGE DEFAULT MESSAGES END OF LIST END OF PAGE ENTER A NEW
LIST IS FULL 6 TO 20 ARE ASSIGNED PASSCODE FOR ACCESS
INVALID PASSCODE INVALID SERVICE CODE KEY PRESSED IS NEW PASSCODE NEW SETPOINT HAS
ENTERED! ENTERED INVALID HERE HAS BEEN ACCEPTED BEEN STORED
NO ALARMS ACTIVE NO TRIPS OR ALARMS OUT OF RANGE.! ENTER: PASSCODE SECURITY PRESS [ENTER] TO ADD
TO RESET #### TO ##### BY # NOT ENABLED, ENTER 0 DEFAULT MESSAGE
PRESS [ENTER] TO RESET PERFORMED ROUNDED SETPOINT SETPOINT ACCESS IS SETPOINT ACCESS IS
REMOVE MESSAGE SUCCESSFULLY HAS BEEN STORED NOW PERMITTED NOW RESTRICTED
TACHOMETER MUST USE THAT DIGITAL INPUT THAT INPUT ALREADY THIS FEATURE NOT THIS PARAMETER IS
INPUT 4, 5, 6, OR 7 IS ALREADY IN USE USED FOR TACHOMETER PROGRAMMED ALREADY ASSIGNED
• NEW SETPOINT HAS BEEN STORED: This message appear each time a
setpoint has been altered and stored as shown on the display.
• ROUNDED SETPOINT HAS BEEN STORED: Since the 489 has a numeric
keypad, an entered setpoint value may fall between valid setpoint values. The
489 detects this condition and store a value rounded to the nearest valid
setpoint value. To find the valid range and step for a given setpoint, press the
HELP key while the setpoint is being displayed.
• OUT OF RANGE! ENTER: #### TO ##### BY #: If a setpoint value outside
the acceptable range of values is entered, the 489 displays this message and
substitutes proper values for that setpoint. An appropriate value may then be
entered.
• ACCESS DENIED, SHORT ACCESS SWITCH: The Access Switch must be
shorted to store any setpoint values. If this message appears and it is necessary
to change a setpoint, short the Access terminals C1 and C2.
• ACCESS DENIED, ENTER PASSCODE: The 489 has a passcode security
feature. If this feature is enabled, not only must the Access Switch terminals be
shorted, but a valid passcode must also be entered. If the correct passcode has
been lost or forgotten, contact the factory with the encrypted access code. All
passcode features may be found in the S1 489 SETUP Z PASSCODE setpoints menu.
• INVALID PASSCODE ENTERED: This flash message appears if an invalid
passcode is entered for the passcode security feature.
• NEW PASSCODE HAS BEEN ACCEPTED: This message will appear as an
acknowledge that the new passcode has been accepted when changing the
passcode for the passcode security feature.
• PASSCODE SECURITY NOT ENABLED, ENTER 0: The passcode security
feature is disabled whenever the passcode is zero (factory default). Any
attempts to enter a passcode when the feature is disabled results in this flash
message, prompting the user to enter “0” as the passcode. When this has been
done, the feature may be enabled by entering a non-zero passcode.
• ENTER A NEW PASSCODE FOR ACCESS: The passcode security feature is
disabled if the passcode is zero. If the CHANGE PASSCODE SETPOINT is entered as
yes, this flash message appears prompting the user to enter a non-zero
Actual Values
passcode and enable the passcode security feature.
• SETPOINT ACCESS IS NOW PERMITTED: Any time the passcode security
feature is enabled and a valid passcode is entered, this flash message appears
to notify that setpoints may now be altered and stored.
• SETPOINT ACCESS IS NOW RESTRICTED: If the passcode security feature is
enabled and a valid passcode entered, this message appears when the S1 489
SETUP Z PASSCODE ZV SETPOINT ACCESS setpoint is altered to “Restricted”. This
message also appears any time that setpoint access is permitted and the access
jumper is removed.
• DATE ENTRY WAS NOT COMPLETE: Since the DATE setpoint has a special
format (entered as MM/DD/YYYY), this message appears and the new value will
not be stored if the ENTER key is pressed before all of the information has been
entered. Another attempt will have to be made with the complete information.
• DATE ENTRY WAS OUT OF RANGE: Appears if an invalid entry is made for
the DATE (for example, 15 entered for the month).
• TIME ENTRY WAS NOT COMPLETE: Since the TIME setpoint has a special
format (entered as HH/MM/SS.s), this message appears and the new value will
not be stored if the ENTER key is pressed before all of the information has been
entered. Another attempt will have to be made with the complete information.
• TIME ENTRY WAS OUT OF RANGE: Appears if an invalid entry is made for the
TIME (for example, 35 entered for the hour).
• NO TRIPS OR ALARMS TO RESET: Appears if the RESET key is pressed when
there are no trips or alarms present.
• RESET PERFORMED SUCCESSFULLY: If all trip and alarm features that are
active can be cleared (that is, the conditions that caused these trips and/or
alarms are no longer present), then this message appears when a reset is
performed, indicating that all trips and alarms have been cleared.
• ALL POSSIBLE RESETS HAVE BEEN PERFORMED: If only some of the trip
and alarm features that are active can be cleared (that is, the conditions that
caused some of these trips and/or alarms are still present), then this message
appears when a reset is performed, indicating that only trips and alarms that
could be reset have been reset.
• ARE YOU SURE? PRESS [ENTER] TO VERIFY: If the RESET key is pressed and
resetting of any trip or alarm feature is possible, this message appears to verify
the operation. If RESET is pressed again while this message is displayed, the
reset will be performed.
• PRESS [ENTER] TO ADD DEFAULT MESSAGE: Appears if the decimal [.] key,
immediately followed by the ENTER key, is entered anywhere in the actual value
message structure. This message prompts the user to press ENTER to add a new
default message. To add a new default message, ENTER must be pressed while
this message is being displayed.
• DEFAULT MESSAGE HAS BEEN ADDED: Appears anytime a new default
message is added to the default message list.
• DEFAULT MESSAGE LIST IS FULL: Appears if an attempt is made to add a
new default message to the default message list when 20 messages are already
assigned. To add a new message, one of the existing messages must be
removed.
• PRESS [ENTER] TO REMOVE MESSAGE: Appears if the decimal [.] key,
immediately followed by the ENTER key, is entered in the S1 489 SETUP ZV DEFAULT
MESSAGES setpoint page. This message prompts the user to press ENTER to
remove a default message. To remove the default message, ENTER must be
pressed while this message is being displayed.
• DEFAULT MESSAGE HAS BEEN REMOVED: Appears anytime a default
message is removed from the default message list.
• DEFAULT MESSAGES 6 of 20 ARE ASSIGNED: Appears anytime the S1 489
Actual Values
SETUP ZV DEFAULT MESSAGES setpoint page is entered, notifying the user of the
number of default messages assigned.
• INVALID SERVICE CODE ENTERED: Appears if an invalid code is entered in
the S12 489 TESTING ZV FACTORY SERVICE setpoints page.
• KEY PRESSED HERE IS INVALID: Under certain situations, certain keys have
no function (for example, any number key while viewing actual values). This
message appears if a keypress has no current function.
• DATA CLEARED SUCCESSFULLY: Confirms that data is reset in the S1 489
SETUP ZV CLEAR DATA setpoints page.
• [.] KEY IS USED TO ADVANCE THE CURSOR: Appears immediately to
prompt the use of the [.] key for cursor control anytime a setpoint requiring
text editing is viewed. If the setpoint is not altered for 1 minute, this message
flashes again.
• TOP OF PAGE: This message will indicate when the top of a page has been
reached.
• BOTTOM OF PAGE: This message will indicate when the bottom of a page has
been reached.
• TOP OF LIST: This message will indicate when the top of subgroup has been
reached.
• END OF LIST: This message will indicate when the bottom of a subgroup has
been reached.
• NO ALARMS ACTIVE: If an attempt is made to enter the Alarm Status
message subgroup, but there are no active alarms, this message will appear.
Actual Values
7 Testing
Test Setup
Description The purpose of this testing description is to demonstrate the procedures necessary
to perform a complete functional test of all the 489 hardware while also testing
firmware/hardware interaction in the process. Since the 489 is packaged in a
drawout case, a demo case (metal carry case in which the 489 may be mounted)
may be useful for creating a portable test set with a wiring harness for all of the
inputs and outputs. Testing of the relay during commissioning using a primary
injection test set will ensure that CTs and wiring are correct and complete.
The 489 tests are listed below. For the following tests refer to Secondary Current
Injection Testing on page 7–2:
1. Output Current Accuracy Test
2. Phase Voltage Input Accuracy Test
3. Ground, Neutral, and Differential Current Accuracy Test
4. Neutral Voltage (Fundamental) Accuracy Test
5. Negative Sequence Current Accuracy Test
6. RTD Accuracy Test
7. Digital Input and Trip Coil Supervision Accuracy Test
8. Analog Input and Outputs Test
9. Output Relay Test
Testing
10. Overload Curve Test
11. Power Measurement Test
12. Reactive Power Test
13. Voltage Phase Reversal Test
For the following tests refer to Secondary Injection Setup #2 on page 7–12:
14. GE Multilin (HGF) Ground Current Accuracy Test
15. Neutral Voltage (3rd Harmonic) Accuracy Test
16. Phase Differential Trip Test
For the following test refer to Secondary Injection Test Setup #3 on page 7–14:
17. Voltage Restrained Overcurrent Test
VC
3 PHASE VARIABLE AC TEST SET
VA
START
VB IN IA IB IC VA VB VC VN
AUTOMATIC CT
1A/5A
1A/5A
1A/5A
1A/5A
1A/5A
1A/5A
Vcom
COM
COM
COM
COM
COM
COM
COM
COM
SHORTING
HGF
Vb
Va
Vc
1A
BAR
V
H12
CONTROL
POWER
H11
A1 HOT
500 Ohms RTD #1
A2 COMPENSATION
A3 RTD RETURN
E12
A4 IRIG - B
COMPENSATION
500 Ohms RTD #2 F12
A5 HOT
SWITCH
E11
A6 HOT TRIP COIL +24VAC
500 Ohms RTD #3 SUPERVISION
F11 SWITCH
A7 COMPENSATION
COMMON
A8 RTD RETURN E2 START
STOP
TRIGGER TRIGGER
A9 COMPENSATION 1 TRIP F1
500 Ohms RTD #4
A10 HOT E1
G
500 Ohms
A11 HOT
RTD #5
F2
R
A12 COMPENSATION 2 AUXILIARY E3
TIMER
A13 RTD RETURN F3
G
RTD 500 Ohms
A14 COMPENSATION
RTD #6
E5
R
SIMULATION A15 HOT 3 AUXILIARY F4
RESISTORS
OR RESISTANCE
DECADE BOX 500 Ohms
D1 HOT
RTD #7
E4
G
D2 COMPENSATION F5
R
D3 RTD RETURN 4 AUXILIARY E6
500 Ohms
D4 COMPENSATION
RTD #8
F6
G
D5 HOT E8
R
D6 HOT 5 ALARM F7
500 Ohms RTD #9
D7 COMPENSATION E7
G
D8 RTD RETURN F8
G
D9 COMPENSATION 6 SERVICE E9
500 Ohms RTD #10
D10 HOT F9
R
D11 HOT
500 Ohms RTD #11
D12 COMPENSATION
D14 COMPENSATION
500 Ohms RTD #12
g
D15 HOT
Testing
D23 COMMON
COM
COM
COM
VDC
+24
1+
3+
1+
3+
2+
4+
2+
4+
-
C3
BREAKER
STATUS
C4 D25 D26 D27 B2 B3 B4 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27
A
A V
RS485 RS485
A
A
808818A3.CDR
Phase Voltage Input The specification for phase voltage input accuracy is ±0.5% of full scale (200 V).
Accuracy Perform the steps below to verify accuracy.
1. Alter the following setpoints in the S2 SYSTEM SETUP ZV VOLTAGE SENSING menu:
VT CONNECTION TYPE: “Wye”
VOLTAGE TRANSFORMER RATIO: “10.00:1”
2. Measured values should be ±1.0 V. Apply the voltage values shown in the table
and verify accuracy of the measured values. View the measured values in the A2
METERING DATA ZV VOLTAGE METERING menu.
Testing
Ground (1 A), Neutral, The specification for neutral, differential and 1 A ground current input accuracy is
and Differential Current ±0.5% of 2 × CT. Perform the steps below to verify accuracy.
Accuracy 1. In the S2 SYSTEM SETUP Z CURRENT SENSING menu, set:
GROUND CT: “1A Secondary”
GROUND CT RATIO: “1000:1”
PHASE CT PRIMARY: “1000 A”
2. In the S5 CURRENT ELEMENTS ZV PHASE DIFFERENTIAL menu, set:
PHASE DIFFERENTIAL TRIP: “Unlatched”
DIFFERENTIAL TRIP MIN. PICKUP: “0.1 x CT”
The last two setpoints are needed to view the neutral and the differential
current. The trip element will operate when differential current exceeds 100 A.
3. Measured values should be ±10 A. Inject (IA only) the values shown in the table
below into one phase only and verify accuracy of the measured values. View the
0.1 A 100 A
0.2 A 200 A
0.5 A 500 A
1A 1000 A
Neutral Voltage The specification for neutral voltage (fundamental) accuracy is ±0.5% of full scale
(Fundamental) (100 V). Perform the steps below to verify accuracy.
Accuracy 1. In the S2 SYSTEM SETUP ZV VOLTAGE SENSING menu, set:
NEUTRAL VOLTAGE TRANSFORMER: “Yes”
NEUTRAL V.T. RATIO: “10.00:1”
2. In the S2 SYSTEM SETUP ZV GEN. PARAMETERS menu, set:
GENERATOR NOMINAL FREQUENCY: “60 Hz”
3. Measured values should be ±5.0 V. Apply the voltage values shown in the table
and verify accuracy of the measured values. View the measured values in the A2
METERING DATA ZV VOLTAGE METERING menu.
Negative Sequence The 489 measures negative sequence current as a percent of Full Load Amperes
Current Accuracy (FLA). A sample calculation of negative sequence current is shown below. Given the
following generator parameters:
Rated MVA (PA) = 1.04
Voltage Phase to Phase (Vpp): 600 V
We have:
PA 6
1.04 × 10
FLA = -----------------------
- = ------------------------------ = 1000 A (EQ 7.1)
3 × V pp 3 × 600
1 2
I ns = --- ( I a + a I b + aI c ) where a = 1 ∠120° = – 0.5 + j0.866
3
1 2
= --- ( 780 ∠0° + ( 1 ∠120° ) ( 1000 ∠– 113° ) + ( 1 ∠120° ) ( 1000 ∠113° ) )
3
1
= --- ( 780 ∠0° + 1000 ∠127° + 1000 ∠233° )
3 (EQ 7.3)
1
= --- ( 780 – 601.8 + j798.6 – 601.8 – j798.6 )
3
= – 141.2
I ns
⇒ %I ns = ---------- × 100 = 14%
FLA
Therefore, the negative sequence current is 14% of FLA. The specification for
negative-sequence current accuracy is per output current inputs. Perform the steps
below to verify accuracy.
1. In the S2 SYSTEM SETUP ZV GEN. PARAMETERS menu, set:
GENERATOR RATED MVA: “1.04”
VOLTAGE PHASE-PHASE: “600”
Note that setting VOLTAGE PHASE-PHASE to “600” is equivalent to setting FLA =
1000 A. This is for testing purposes only!
2. In the S2 SYSTEM SETUP Z CURRENT SENSING menu, set:
PHASE CT PRIMARY: “1000 A”
3. Inject the values shown in the table below and verify accuracy of the measured
values. View the measured values in the A2 METERING DATA Z CURRENT METERING
menu.
RTD Accuracy The specification for RTD input accuracy is ±2° for Platinum/Nickel and ±5° for
Copper. Perform the steps below.
Testing
1. In the S8 RTD TEMPERATURE MENU, set:
RTD TYPE Z STATOR RTD TYPE: “100 Ohm Platinum” (select desired type)
RTD #1 Z RTD #1 APPLICATION: “Stator” (repeat for RTDs 2 to 12)
2. Measured values should be ±2°C / ±4°F for platinum/nickel and ±5°C / ±9°F for
copper. Alter the resistance applied to the RTD inputs as shown below to simu-
late RTDs and verify accuracy. View the measured values in A2 METERING DATA
ZV TEMPERATURE.
Digital Inputs and Trip The digital inputs and trip coil supervision can be verified easily with a simple switch
Coil Supervision or pushbutton. Verify the Switch +24 V DC with a voltmeter. Perform the steps
below to verify functionality of the digital inputs.
1. Open switches of all of the digital inputs and the trip coil supervision circuit.
2. View the status of the digital inputs and trip coil supervision in the A1 STATUS ZV
DIGITAL INPUTS menu.
3. Close switches of all of the digital inputs and the trip coil supervision circuit.
4. View the status of the digital inputs and trip coil supervision in the A1 STATUS ZV
DIGITAL INPUTS menu.
Analog Inputs and The specification for analog input and analog output accuracy is ±1% of full scale.
Outputs Perform the steps below to verify accuracy. Verify the Analog Input +24 V DC with a
voltmeter.
4 to 20 mA Inputs:
1. In the S11 ANALOG I/O ZV ANALOG INPUT 1 menu, set:
ANALOG INPUT 1: “4-20 mA”
ANALOG INPUT 1 MINIMUM: “0”
ANALOG INPUT 1 MAXIMUM: “1000” (repeat all for Analog Inputs 2 to 4)
2. Analog output values should be ±0.2 mA on the ammeter. Measured analog
input values should be ±10 units. Force the analog outputs using the following
setpoints from the S12 TESTING ZV TEST ANALOG OUTPUT menu:
FORCE ANALOG OUTPUTS FUNCTION: “Enabled”
ANALOG OUTPUT 1 FORCED VALUE: “0%” (enter %, repeat for Outputs 2 to 4)
Testing
3. Verify the ammeter readings and the measured analog input readings. For the
purposes of testing, the analog input is fed in from the analog output (see Sec-
ondary Current Injection Testing on page 7–2). View the measured values in
the A2 METERING DATA Z ANALOG INPUTS menu.
0 to 1 mA Analog Inputs:
1. In the S11 ANALOG I/O ZV ANALOG INPUT 1 menu, set:
ANALOG INPUT 1: “0-1 mA”
ANALOG INPUT 1 MINIMUM: “0”
ANALOG INPUT 1 MAXIMUM: “1000” (repeat for Analog Inputs 2 to 4)
2. Analog output values should be ±0.01 mA on the ammeter. Measured analog
input values should be ±10 units. Force the analog outputs using the following
setpoints in the S12 TESTING ZV TEST ANALOG OUTPUT menu:
FORCE ANALOG OUTPUTS FUNCTION: “Enabled”
ANALOG OUTPUT 1 FORCED VALUE: “0%” (enter %, repeat for Outputs 2 to 4)
3. Verify the ammeter readings as well as the measured analog input readings.
View the measured values in the A2 METERING DATA ZV ANALOG INPUTS menu.
Output Relays To verify the functionality of the output relays, perform the following steps:
1. Using the setpoint:
S12 TESTING ZV TEST OUTPUT RELAYS ZV FORCE OPERATION OF RELAYS: “1 Trip”
select and store values as per the table below, verifying operation
All Relays
No Relays
Testing
1750 A 1.75 × FLA 169.66 s 166.27 to 173.05 s
3000 A 3.00 × FLA 43.73 s 42.86 to 44.60 s
6000 A 6.00 × FLA 9.99 s 9.79 to 10.19 s
10000 A 10.00 × FLA 5.55 s 5.44 to 5.66 s
Power Measurement The specification for reactive and apparent power is ± 1% of 3 × 2 × CT × VT × VTfull-
Test at Iavg < 2 × CT. Perform the steps below to verify accuracy.
scale
1. In the S2 SYSTEM SETUP Z CURRENT SENSING menu, set:
PHASE CT PRIMARY: “1000”
2. In the S2 SYSTEM SETUP ZV VOLTAGE SENSING menu, set:
VT CONNECTION TYPE: “Wye”
VOLTAGE TRANSFORMER RATIO: “10.00:1”
3. Inject current and apply voltage as per the table below. Verify accuracy of the
measured values. View the measured values in the A2 METERING DATA ZV POWER
METERING menu:
Reactive Power The specification for reactive power is ±1% of 3 × 2 × CT × VT × VTfull scale at
Accuracy Iavg < 2 × CT. Perform the steps below to verify accuracy and trip element.
1. In the S2 SYSTEM SETUP Z CURRENT SENSING menu, set:
PHASE CT PRIMARY: “5000”
2. In the S2 SYSTEM SETUP ZV VOLTAGE SENSING menu, set:
VT CONNECTION TYPE: “Wye”
VOLTAGE TRANSFORMER RATIO: “100:1”
3. In the S2 SYSTEM SETUP ZV GEN. PARAMETERS menu, set
GENERATOR RATED MVA: “100”
GENERATOR RATED POWER FACTOR: “0.85”
GENERATOR VOLTAGE PHASE-PHASE: “12000”
–1
The rated reactive power is 100 sin ( cos ( 0.85 ) ) = ± 52.7 Mvar .
4. Alter the following reactive power setpoints in the S7 POWER ELEMENTS Z REAC-
TIVE POWER menu:
REACTIVE POWER ALARM: “Unlatched”
ASSIGN ALARM RELAYS(2-5): “---5”
POSTIVE MVAR ALARM LEVEL: “0.6 x Rated”
Testing
Voltage Phase The can detect voltage phase rotation and protect against phase reversal. To test
Reversal Accuracy the phase reversal element, perform the following steps:
1. In the S2 SYSTEM SETUP ZV VOLTAGE SENSING menu, set:
VT CONNECTION TYPE: “Wye”
2. In the S2 SYSTEM SETUP ZV GEN. PARAMETERS menu, set:
GENERATOR PHASE SEQUENCE: “ABC”
3. In the S3 DIGITAL INPUTS Z BREAKER STATUS menu, set:
BREAKER STATUS: “Breaker Auxiliary a”
4. In the S6 VOLTAGE ELEMENTS ZV PHASE REVERSAL menu, set:
PHASE REVERSAL TRIP: “Unlatched”
ASSIGN TRIP RELAYS: “1---”
5. Apply voltages as per the table below. Verify the operation on voltage phase
reversal
Testing
Applied Voltage Expected Result Observed Result
Va = 120 V∠0° No Trip
Vb = 120 V∠120° lag
Vc = 120 V∠240° lag
Va = 120 V∠0° Phase Reversal Trip
Vb = 120 V∠240° lag
Vc = 120 V∠120° lag
Injection Test Setup #2 Setup the 489 device as follows for the GE Multilin HGF Ground Accuracy Test,
Neutral Voltage (3rd Harmonic) Accuracy Test, and the Phase Differential Trip Test.
VC
3 PHASE VARIABLE AC TEST SET
VA
VB VA VB VC VN IA IB IC IN
NC NC
50:0.25
AUTOMATIC CT
1A/5A
1A/5A
1A/5A
1A/5A
1A/5A
1A/5A
Vcom
COM
COM
COM
COM
COM
COM
COM
COM SHORTING
HGF
Vb
Va
Vc
1A
BAR
V
808817A1.CDR
GE Multilin 50:0.025 The specification for GE Multilin HGF 50:0.025 ground current input accuracy is
Ground Accuracy ±0.5% of 2 × CT rated primary (25 A). Perform the steps below to verify accuracy.
1. In the S2 SYSTEM SETUP Z CURRENT SENSING menu, set:
GROUND CT: “50:0.025 CT”
2. Measured values should be ±0.25 A. Inject the values shown in the table below
either as primary values into a GE Multilin 50:0.025 Core Balance CT or as sec-
ondary values that simulate the core balance CT. Verify accuracy of the mea-
sured values in the A2 METERING DATA Z CURRENT METERING menu.
1A 0.5 mA 1.00 A
5A 2.5 mA 5.00 A
10 A 5 mA 10.00 A
Neutral Voltage (3rd The 489 specification for neutral voltage (3rd harmonic) accuracy is ±0.5% of full
Harmonic) Accuracy scale (100 V). Perform the steps below to verify accuracy.
1. In the S2 SYSTEM SETUP ZV VOLTAGE SENSING menu, set
NEUTRAL VOLTAGE TRANSFORMER: “Yes”
NEUTRAL V.T. RATIO: “10.00:1”
2. In the S2 SYSTEM SETUP ZV GEN. PARAMETERS menu, set:
GENERATOR NOMINAL FREQUENCY: “60 Hz”
3. Measured values should be ±5.0 V. Apply the voltage values shown in the table
and verify accuracy of the measured values. View the measured values in the A2
METERING DATA ZV VOLTAGE METERING menu.
Phase Differential Trip These tests will require a dual channel current source. The unit must
Accuracy be capable of injecting prefault currents and fault currents of a
NOTE different value. Application of excessive currents (greater than 3 ×
CT) for extended periods will cause damage to the relay.
c) Slope 1 Check
4. Connect the relay test set to inject Channel Y current (IY) into the G6 terminal
and out of H6 terminal. The angle between Ix and IY will be 180°.
5. Set pre-fault current, Ix and IY equal to zero.
6. Set fault current, IY equal to 1½ CT.
7. At this value the relay should operate according to the following formula:
2 – Slope 1 setting 3 × CT
I XOP1 = ------------------------------------------------------- × ------------------ (EQ 7.6)
2 + Slope 1 setting 2
8. Set fault current, Ix equal to 0.95 × IXOP1. Apply the fault. The relay should
operate. Switch off the current.
9. Set fault current, Ix equal to 1.05 × IXOP1. Apply the fault. The relay should
restrain. Switch off the current.
Testing
d) Slope 2 Check
10. Set fault current, IY equal to 2.5 × CT.
11. At this value the relay should operate according to the following formula.
2 – Slope 2 setting
I XOP2 = ------------------------------------------------------- × 3.5 × CT (EQ 7.7)
2 + Slope 2 setting
12. Set fault current, Ix equal to 0.95 × IXOP2. Switch on the test set. The relay
should operate. Switch off the current.
13. Set fault current, Ix equal to 1.05 × IXOP2. Switch on the test set. The relay
should restrain. Switch off the current.
e) Directional Check
14. Set pre-fault current, Ix and IY equal to 3.5 × CT. At this value the conditions for
CT saturation detection are set and the relay will enable the directional check.
15. Set fault current, Ix equal to 0.95 × IXOP2. Switch on the test set. The relay
should restrain. Switch off the current.
16. Repeat Steps 1 through 15 for phases B and C.
f) Test Results
Injection Test Setup #3 Setup the 489 device as follows for the Voltage Restrained Overcurrent test.
VC
3 PHASE VARIABLE AC TEST SET
VA
VB VA VB VC VN IA IB IC IN
Testing
AUTOMATIC CT
1A/5A
1A/5A
1A/5A
1A/5A
1A/5A
1A/5A
Vcom
COM
COM
COM
COM
COM
COM
COM
COM
SHORTING
HGF
Vb
Va
Vc
1A
BAR
V
808822A2.CDR
Voltage Restrained Setup the relay as shown in FIGURE 7–3: Secondary Injection Test Setup #3 on
Overcurrent Accuracy page 7–14.
1. In the S2 SYSTEM SETUP ZV GEN. PARAMETERS menu, set:
GENERATOR RATED MVA: “100 MVA”
GENERATOR VOLTAGE PHASE-PHASE: “12000”
2. In the S2 SYSTEM SETUP ZV VOLTAGE SENSING menu, set:
VT CONNECTION TYPE: “Open Delta”
VOLTAGE TRANSFORMER RATIO: “100:1”
3. In the S5 CURRENT ELEMENTS Z OVERCURRENT ALARM menu, set:
OVERCURRENT ALARM: “Unlatched”
O/C ALARM LEVEL: “1.10 x FLA”
OVERCURRENT ALARM DELAY: “2 s”
O/C ALARM EVENTS: “On”
4. In the S5 CURRENT ELEMENTS ZV PHASE OVERCURRENT menu, set:
PHASE OVERCURRENT TRIP: “Latched”
ENABLE VOLTAGE RESTRAINT: “Yes”
PHASE O/C PICKUP: “1.5 x CT”
CURVE SHAPE: “ANSI Extremely Inv.”
O/C CURVE MULTIPLIER: “2.00”
O/C CURVE RESET: “Instantaneous”
5. The trip time for the extremely inverse ANSI curve is given as:
⎛ B D E ⎞
⎜ A + -------------------------------
- + ----------------------------------------- + -----------------------------------------⎟
Time to Trip = M × ⎜ I I - – C⎞ 2 I - – C⎞ ⎟ 3 (EQ 7.8)
⎜ ---------------------- – C ⎛ --------------------- ⎛ ---------------------
〈 K〉 × I p ⎝ 〈 K〉 × I ⎠ ⎝ 〈 K〉 × I ⎠ ⎟
⎝ p p ⎠
Testing
the event records in the A5 EVENT RECORD menu.
Distance Element The theoretical impedance on the R-X plane can be calculated as:
Accuracy 2 2
0.875 × Z d × cos ( θ d – θ i ) + ( 0.875 × Z d × cos ( θ d – θ i ) ) + 4 × Z d × 0.125
Z i = ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- (EQ 7.10)
2
where: Zd = programmed distance impedance
θd = programmed distance characteristic angle
θi = variable angle on the R-X plane at point i for which boundary
impedance is to be calculated
It is recommended that voltage is kept constant while increasing the current
magnitude at certain angles referenced to voltage phase A until element operates.
Then the expected operating current (assuming that current in the two phases are
180° apart) can be calculated as:
Va – Vb
I i = -------------------
- (EQ 7.11)
2Z i
jθ i
where Z i = Z i × e .
Testing
8 Appendix
Neutral Overvoltage The simplest, and one of the oldest methods to detect stator ground faults on high-
Element impedance-grounded generators, is to sense the voltage across the stator
grounding resistor (See References [1, 2] at the end of this section). This is Appendix
illustrated, in a simplified form in the figure below. The voltage signal is connected
to the Vneutral input of the 489, terminals E10 and F10. The Vneutral signal is the
input signal for the 489 neutral overvoltage protection element. This element has an
alarm and a trip function, with separately adjustable operate levels and time delays.
The trip function offers a choice of timing curves as well as a definite time delay. The
neutral overvoltage function responds to fundamental frequency voltage at the
generator neutral. It provides ground fault protection for approximately 95% of the
stator winding. The limiting factor is the level of voltage signal available for a fault in
the bottom 5% of the stator winding. The element has a range of adjustment, for
the operate levels, of 2 to 100 V.
Generator
R is selected for a
maximum fault current
of 10 A, typically.
Distribution Overvoltage
R Relay
Transformer
808739A1.CDR
FIGURE 8–1: Stator Ground Fault Protection
The operating time of this element should be coordinated with protective elements
downstream, such as feeder ground fault elements, since the neutral overvoltage
element will respond to external ground faults if the generator is directly connected
to a power grid, without the use of a delta-wye transformer.
In addition, the time delay should be coordinated with the ground directional
element (discussed later), if it is enabled, by using a longer delay on the neutral
overvoltage element than on the directional element.
It is recommended that an isolation transformer be used between the relay and the
grounding impedance to reduce common mode voltage problems, particularly on
installations requiring long leads between the relay and the grounding impedance.
When several small generators are operated in parallel with a single step-up
transformer, all generators may be grounded through the same impedance (the
impedance normally consists of a distribution transformer and a properly sized
resistor). It is possible that only one generator is grounded while the others have a
floating neutral point when connected to the power grid (see the figure below). This
operating mode is often adopted to prevent circulation of third-harmonic currents
through the generators, if the installation is such that all the star points would end
up connected together ahead of the common grounding impedance (if each
generator has its own grounding impedance, the magnitude of the circulating third
harmonic current will be quite small). With a common ground point, the same
Vneutral signal is brought to all the relays but only the one which is grounded should
have the neutral overvoltage element in service.
For these cases, the neutral overvoltage element has been provided with a
supervising signal obtained from an auxiliary contact off the grounding switch.
When the grounding switch is opened, the element is disabled. The grounding
switch auxiliary contact is also used in the ground directional element, as is the
breaker auxiliary contact, as discussed later.
Appendix
If all the generators are left grounded through the same impedance, the neutral
overvoltage element in each relay will respond to a ground fault in any of the
generators. For this reason, the ground directional element should be used in each
relay, in addition to the neutral overvoltage element.
Common
Grounding G1 Breaker
Impedance Grounding
Switch
Trans. & R
Aux.
Contact Aux.
Isolating
Trans. Contact
489
Vneutral Relay
G2 Breaker
Grounding
Switch
Aux.
Contact Aux.
Contact
489
Vneutral Relay
Other Generators,
as the case may be
808737A1.CDR
Ground Overcurrent The ground overcurrent element can be used as a direct replacement or a backup
Element for the neutral overvoltage element, with the appropriate current signal from the
generator neutral point, for grounded generators. This element can also be used
with a Core Balance CT, either in the neutral end or the output end of the generator,
as shown below. The use of the special CT, with its dedicated input to the relay,
offers very sensitive current detection, but still does not offer protection for the full
stator. The setting of this element must be above the maximum unbalance current
that normally flows in the neutral circuit. Having the element respond only to the
fundamental frequency component allows an increase in sensitivity.
The core balance CT can be a conventional CT or a 50:0.025 Ground CT, allowing
the measurement of primary-side current levels down to 0.25 A. Using a Core
Balance CT, on the output side of the transformer will provide protection against
stator ground faults in ungrounded generators, provided that there is a source of
zero-sequence current from the grid.
Though in theory one could use this element with a zero sequence current signal
obtained from a summation of the three phase currents (neutral end or output end),
by connecting it in the star point of the phase CTs, Options 4 and 5 in the figure
below, this approach is not very useful. The main drawback, for impedance-
grounded generators is that the zero-sequence current produced by the CT ratio and Appendix
phase errors could be much larger than the zero sequence current produced by a
real ground fault inside the generator.
Again the time delay on this element must be coordinated with protection elements
downstream, if the generator is grounded. Refer to Ground Directional on page 5–32
for the range of settings of the pickup levels and the time delays. The time delay on
this element should always be longer than the longest delay on line protection
downstream.
GENERATOR
Option 2 Option 5
(similar to Option 3 Breaker
Option 4) Aux.
Option 1
489
Option 4
808736A1.CDR
Ground Directional The 489 can detect internal stator ground faults using a Ground Directional element
Element implemented using the Vneutral and the ground current inputs. The voltage signal is
obtained across the grounding impedance of the generator. The ground, or zero
sequence, current is obtained from a core balance CT, as shown below (due to CT
inaccuracies, it is generally not possible to sum the outputs of the conventional
phase CTs to derive the generator high-side zero sequence current, for an
impedance-grounded generator).
If correct polarities are observed in the connection of all signals to the relay, the
Vneutral signal will be in phase with the ground current signal. The element has been
provided with a setting allowing the user to change the plane of operation to cater
to reactive grounding impedances or to polarity inversions.
This element’s normal ‘plane of operation’ for a resistor-grounded generator is the
180° plane, as shown in FIGURE 8–4: Ground Directional Element Polarities and
Plane of Operation, for an internal ground fault. That is, for an internal stator-to-
ground fault, the Vo signal is 180° away from the Io signal, if the polarity convention
is observed. If the grounding impedance is inductive, the plane of operation will be
the 270° plane, again, with the polarity convention shown below. If the polarity
convention is reversed on one input, the user will need to change the plane of
operation by 180°.
±
F10 H10
489
Relay Io
E10 G10
270°
±
Isolating
Transformer 808735A1.CDR
GENERATOR
CORE
BREAKER
BALANCE
CT
Aux.
Contact
Grounding
Switch Aux.
To Relay 489 Breaker
Grounding Ground
Ground
Impedance Vneutral Directional
Current
(Trans. & Input Element
Input
Resistor) (or O/C)
Isolating
Transformer
Neutral Ground
O/V O/C
Element Element
Third Harmonic Voltage The conventional neutral overvoltage element or the ground overcurrent element
Element are not capable of reliably detecting stator ground faults in the bottom 5% of the
stator, due to lack of sensitivity. In order to provide reliable coverage for the bottom
part of the stator, protective elements, utilizing the third harmonic voltage signals in
the neutral and at the generator output terminals, have been developed (see
Reference 4).
In the 489 relay, the third-harmonic voltage element, Neutral Undervoltage (3rd
Harmonic) derives the third harmonic component of the neutral-point voltage signal
from the Vneutral signal as one signal, called VN3. The third harmonic component of
the internally summed phase-voltage signals is derived as the second signal, called
VP3. For this element to perform as originally intended, it is necessary to use wye-
connected VTs.
Since the amount of third harmonic voltage that appears in the neutral is both load
and machine dependent, the protection method of choice is an adaptive method.
The following formula is used to create an adaptive third-harmonic scheme:
V N3
- ≤ 0.15
---------------------------------- which simplifies to V P3 ≥ 17V N3 (EQ 8.1)
V P3 ⁄ 3 + V N3
The 489 tests the following conditions prior to testing the basic operating equation
to ensure that VN3 is of a measurable magnitude:
Neutral CT Ratio
V P3′ > 0.25 V and V P3′ ≥ Permissive_Threshold × 17 × ------------------------------------------------- (EQ 8.2)
Phase CT Ratio
where: VN3 is the magnitude of third harmonic voltage at the generator neutral
VP3 is the magnitude of third harmonic voltage at the generator terminals
VP3' and VN3' are the corresponding voltage transformer secondary values
Permissive_Threshold is 0.15 V for the alarm element and 0.1875 V for the
trip element.
In addition, the logic for this element verifies that the generator positive sequence
terminal voltage is at least 30% of nominal, to ensure that the generator is actually
excited.
This method of using 3rd harmonic voltages to detect stator ground faults near the
generator neutral has proved feasible on larger generators with unit transformers.
NOTE Its usefulness in other generator applications is unknown.
If the phase VT connection is “Open Delta”, it is not possible to measure the third
harmonic voltage at the generator terminals and a simple third harmonic neutral
undervoltage element is used. In this case, the element is supervised by both a
terminal voltage level and by a power level. When used as a simple undervoltage
element, settings should be based on measured 3rd harmonic neutral voltage of the
healthy machine. It is recommended that the element only be used for alarm
purposes with open delta VT connections.
References 1. C. R. Mason, “The Art & Science of Protective Relaying”, John Wiley & Sons,
Inc., 1956, Chapter 10.
2. J. Lewis Blackburn, “Protective Relaying: Principles and Applications”, Marcel
Dekker, Inc., New York, 1987, chapter 8.
Appendix
Current Transformers
Ground Fault CTs for CTs that are specially designed to match the ground fault input of GE Multilin motor
50:0.025 A CT protection relays should be used to ensure correct performance. These CTs have a
50:0.025A (2000:1 ratio) and can sense low leakage currents over the relay setting
range with minimum error. Three sizes are available with 3½-inch, 5½-inch, or 8-
inch diameter windows.
DIMENSIONS DIMENSIONS
Appendix
808710A1.CDR
Ground Fault CTs for For low resistance or solidly grounded systems, a 5 A secondary CT should be used.
5 A Secondary CT Two sizes are available with 5½” or 13” × 16” windows. Various Primary amp CTs can
be chosen (50 to 250).
GCT5 GCT16
DIMENSIONS DIMENSIONS
808709A1.CDR
Appendix
Phase CTs Current transformers in most common ratios from 50:5 to 1000:5 are available for
use as phase current inputs with motor protection relays. These come with
mounting hardware and are also available with 1 A secondaries. Voltage class:
600 V BIL, 10 KV.
808712A1.CDR
Appendix
100
MULTIPLIER
10
30.0
TRIP TIME (sec)
20.0
15.0
10.0
8.0
6.0
1
4.0
3.0
2.0
1.0
0.1 0.5
Appendix
0.01
0.1 1 10 100
489 ANSI
GE Multilin NORMALLY INVERSE
1000
100
10 MULTIPLIER
TRIP TIME (sec)
30.0
20.0
15.0
10.0
1 8.0
6.0
4.0
3.0
2.0
1.0
0.1
0.5
Appendix
0.01
0.1 1 10 100
CURRENT (I/Ipu) 808801A4.CDR
FIGURE 8–7: ANSI Normally Inverse Curves
489 ANSI
GE Multilin VERY INVERSE
1000
100
10
MULTIPLIER
TRIP TIME (sec)
30.0
20.0
15.0
1 10.0
8.0
6.0
4.0
3.0
2.0
0.1 1.0
0.5
Appendix
0.01
0.1 1 10 100
CURRENT (I/Ipu) 808800A4.DWG
489 ANSI
GE Multilin EXTREME INVERSE
1000
100
10
TRIP TIME (sec)
MULTIPLIER
30.0
20.0
1
15.0
10.0
8.0
6.0
4.0
3.0
2.0
0.1
1.0
Appendix
0.5
0.01
0.1 1 10 100
808799A4.CDR
CURRENT (I/Ipu)
FIGURE 8–9: ANSI Extremely Inverse Curves
1000
100
10
TRIP TIME (sec)
MULTIPLIER
30.0
20.0
15.0
1 10.0
8.0
6.0
4.0
3.0
2.0
0.1 1.0
Appendix
0.5
0.01
0.1
100
10
1
IAC Curves
489 IAC
GE Multilin
SHORT INVERSE
1000
100
MULTIPLIER
10
TRIP TIME (sec)
30.0
1
20.0
15.0
10.0
8.0
6.0
4.0
3.0
0.1
2.0
1.0 Appendix
0.5
0.01
0.1
10
100
489
GE Multilin IAC INVERSE
1000
100
10 MULTIPLIER
30.0
TRIP TIME (sec)
20.0
15.0
10.0
8.0
6.0
1 4.0
3.0
2.0
1.0
0.5
0.1
Appendix
0.01
1
0.1
10
100
489 IAC
GE Multilin VERY INVERSE
1000
100
10
MULTIPLIER
TRIP TIME (sec)
30.0
20.0
15.0
10.0
1 8.0
6.0
4.0
3.0
2.0
1.0
0.1
0.5
Appendix
0.01
0.1
10
100
1
489 IAC
GE Multilin
EXTREME INVERSE
1000
100
10
TRIP TIME (sec)
MULTIPLIER
30.0
1
20.0
15.0
10.0
8.0
6.0
4.0
3.0
0.1
2.0
Appendix
1.0
0.5
0.01
0.1
10
100
IEC Curves
489
GE Multilin IEC CURVE A (BS142)
1000
100
10
TRIP TIME (sec)
MULTIPLIER
1.00
0.80
0.60
0.50
1
0.40
0.30
0.20
0.15
0.10
0.05
0.1
Appendix
0.01
0.1
10
100
1
489
GE Multilin IEC CURVE B (BS142)
1000
100
10
TRIP TIME (sec)
MULTIPLIER
1.00
0.80
0.60
0.50
0.40
0.30
0.20
0.1
0.15
0.10
Appendix
0.05
0.01
0.1
100
10
489
GE Multilin IEC CURVE C (BS142)
1000
100
10
TRIP TIME (sec)
MULTIPLIER
1.00
0.80
0.60
0.1 0.50
0.40
0.30
Appendix
0.20
0.15
0.10
0.01
0.05
1
10
0.1
100
Revision History
Change Notes
Table 8–2: Revision History
MANUAL P/N REVISION RELEASE DATE ECO
1601-0150-A1 3.00 26 April 2004 489-249
1601-0150-A2 3.00 21 May 2004 ---
1601-0150-A3 3.00 22 July 2004 ---
1601-0150-A4
Additional changes for revision A2 were cosmetic. There was no change to content.
Appendix
EU Declaration of Conformity
EU Declaration of
Conformity
Appendix
Warranty
GE Multilin Warranty General Electric Multilin Inc. (GE Multilin) warrants each relay it manufactures to be
free from defects in material and workmanship under normal use and service for a
period of 24 months from date of shipment from factory.
In the event of a failure covered by warranty, GE Multilin will undertake to repair or
replace the relay providing the warrantor determined that it is defective and it is
returned with all transportation charges prepaid to an authorized service centre or
the factory. Repairs or replacement under warranty will be made without charge.
Warranty shall not apply to any relay which has been subject to misuse, negligence,
accident, incorrect installation or use not in accordance with instructions nor any
unit that has been altered outside a GE Multilin authorized factory outlet.
GE Multilin is not liable for special, indirect or consequential damages or for loss of
profit or for expenses sustained as a result of a relay malfunction, incorrect
application or adjustment.
For complete text of Warranty (including limitations and disclaimers), refer to GE
Multilin Standard Conditions of Sale.
Appendix
Index
GE Multilin http://www.GEmultilin.com i
489
Generator Management Relay
L
F
LAST TRIP DATA .............................. 5-13, 5-18, 6-4, 6-8, 6-10
FACTORY SERVICE .......................................................... 5-85 LEARNED PARAMETERS ....................................................5-18
FAULT SETUP ................................................................... 5-83 LEDs .......................................................................... 4-1, 4-2
FAX NUMBERS ................................................................... 1-1 LONG-TERM STORAGE .....................................................2-11
FEATURES .................................................................. 2-2, 2-7 LOOP POWERED TRANSDUCERS ......................................3-13
FIELD-BREAKER DISCREPANCY ......................................... 2-8 LOSS OF EXCITATION ...............................................2-6, 5-44
FIRMWARE LOSS OF LOAD .................................................................. 4-2
upgrading via EnerVista 489 setup software ................ 4-21 LOW FORWARD POWER ...................................................5-51
FLASH MESSAGES ........................................................... 6-26
FLEXCURVE ..................................................................... 5-24
FLOW ............................................................................... 3-12
FREQUENCY TRACKING ..................................................... 2-5
FRONT PANEL
M
using ............................................................................... 1-2
MACHINE COOLING ..........................................................5-68
FUSE ................................................................................. 2-9
MESSAGE SCRATCHPAD ...................................................5-12
METERING
current ..........................................................................6-14
demand ..................................................................2-8, 6-17
G Mvarh .......................................................... 5-13, 5-18, 6-16
MWh ............................................................ 5-13, 5-18, 6-16
GENERAL COUNTERS ....................................................... 6-22 power ............................................................................. 2-9
GENERAL INPUTS ..................................................... 2-8, 5-17 specifications ................................................................. 2-3
GENERATOR INFORMATION ............................................. 5-13 voltage ..........................................................................6-15
GENERATOR LOAD ........................................................... 6-18 MODEL INFORMATION .....................................................6-25
GENERATOR PARAMETERS .............................................. 5-15 MODEL SETUP ..................................................................5-57
GENERATOR STATUS ......................................................... 6-3 MOTOR STARTS ...............................................................5-18
GETTING STARTED ............................................................ 1-1 MOTOR TRIPS ..................................................................5-18
GROUND CT MVA DEMAND ......................................................... 5-75, 6-17
burden ............................................................................ 2-5 MVAR DEMAND ....................................................... 5-75, 6-17
setpoint ........................................................................ 5-14 Mvarh METERING ........................................... 5-13, 5-18, 6-16
withstand ........................................................................ 2-5 MW DEMAND ........................................................... 5-75, 6-17
GROUND CURRENT ACCURACY TEST ........................ 7-3, 7-12 MWh METERING ............................................. 5-13, 5-18, 6-16
GROUND CURRENT INPUT ............................................... 3-10
GROUND DIRECTIONAL ............................................ 5-32, 8-4
GROUND FAULT CTs .......................................................... 8-8
GROUND OVERCURRENT .......................................... 5-30, 8-3
GROUND SWITCH STATUS .............................................. 5-21
N
NAMEPLATE ....................................................................... 1-1
NEGATIVE SEQUENCE CURRENT ACCURACY TEST ............ 7-4
NEGATIVE SEQUENCE OVERCURRENT ..............................5-28
H NEGATIVE-SEQUENCE CURRENT ......................................6-14
NEUTRAL CURRENT ACCURACY TEST ................................ 7-3
HELP KEY .......................................................................... 1-7 NEUTRAL OVERVOLTAGE ..........................................5-41, 8-1
HIGH-SET PHASE OVERCURRENT .................................... 5-33
ii http://www.GEmultilin.com GE Multilin
489
Generator Management Relay
U
UNBALANCE BIAS ............................................................ 5-67
UNDERFREQUENCY .......................................................... 5-39
UNDERVOLTAGE ....................................................... 2-8, 5-34
UNPACKING THE RELAY ..................................................... 1-1
UPGRADING FIRMWARE .................................................. 4-21
iv http://www.GEmultilin.com GE Multilin