Macropoxy 646 PW 2021
Macropoxy 646 PW 2021
646 PW
POTABLE WATER EPOXY
&
Marine Pඉකග A B58WX610
Pඉකග A B58LX600 Lඑඏඐග Bඔඝඍ Pඉකග A B58HX610
Mඑඔඔ Wඐඑගඍ
Bඝඎඎ
Coatings Pඉකග A B58RX610 Rඍඌ
Pඉකග A B58RX611 1211 Rඍඌ
Pඉකග B B58VX600 Hඉකඌඍඖඍක
Pඉකග B B58VX605 OAP Hඉකඌඍඖඍක
Dਨਲਢਫਠਨਬਤ Wਠਠਭਲ਼ਸ
The Sherwin-Williams Company warrants our products to be free of manufactur-
The information and recommendations set forth in this Product Data Sheet are ing defects in accord with applicable Sherwin-Williams quality control procedures.
based upon tests conducted by or on behalf of The Sherwin-Williams Company. Liability for products proven defective, if any, is limited to replacement of the defec-
Such information and recommendations set forth herein are subject to change and tive product or the refund of the purchase price paid for the defective product as
pertain to the product offered at the time of publication. Consult your Sherwin- determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
Williams representative to obtain the most recent Product Data Information and OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
Application Bulletin. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
www.sherwin-williams.com/protective
Protective MACROPOXY ®
646 PW
POTABLE WATER EPOXY
&
Marine Pඉකග A B58WX610
Pඉකග A B58LX600 Lඑඏඐග Bඔඝඍ Pඉකග A B58HX610
Mඑඔඔ Wඐඑගඍ
Bඝඎඎ
Coatings Pඉකග A B58RX610 Rඍඌ
Pඉකග A B58RX611 1211 Rඍඌ
Pඉකග B B58VX600 Hඉකඌඍඖඍක
Pඉකග B B58VX605 OAP Hඉකඌඍඖඍක
Drying Schedule @ 7.0 mils wet (175 microns): Do not use Quik-Kick Epoxy Accelerator for immersion ser-vice
when UL certification is required.
@ 40°F/4.5°C @ 77°F/25°C @ 100°F/38°C
50% RH Insufficient ventilation, incomplete mixing, miscatalyzation, and
To touch: 4-5 hours 2 hours 1.5 hours external heaters may cause premature yellowing.
To handle: 48 hours 8 hours 4.5 hours Excessive film build, poor ventilation, and cool temperatures may
To recoat: cause solvent entrapment and premature coating failure.
minimum: 48 hours 8 hours 4.5 hours
maximum: 1 year 1 year 1 year For Immersion Service: (if required) Holiday test in accordance
Cure for with ASTM D5162 for steel, or ASTM D4787 for concrete.
immersion: 14 days 7 days 4 days Guidance on techniques and required equipment to inspect a
If maximum recoat time is exceeded, abrade surface before recoating. coating system incorporating Opti-Check OAP Technology can
Drying time is temperature, humidity, and film thickness dependent. be found in SSPC-TU 11.
Pot Life: 10 hours 4 hours 2 hours
Refer to Product Information sheet for additional performance
Sweat-in-Time: 30 minutes 30 minutes 15 minutes characteristics and properties.
For Potable Water Service, allow a minimum cure time of 7 days at 77°F
(25°C) prior to placing in service. Sterilize and rinse per AWWA C652. Sਠਥਤਲ਼ਸ Pਤਢਠਲ਼ਨਮਭਲ
Application of coating above maximum or below minimum Refer to the SDS sheet before use.
recommended spreading rate may adversely affect coating
performance. Published technical data and instructions are subject to change without notice.
Contact your Sherwin-Williams representative for additional technical data and
Cਫਤਠਭ Uਯ Iਭਲਲ਼ਢਲ਼ਨਮਭਲ instructions.
Clean spills and spatters immediately with Reducer R7K15. Clean tools
immediately after use with Reducer R7K15. Wਠਠਭਲ਼ਸ
The Sherwin-Williams Company warrants our products to be free of manufacturing
Dਨਲਢਫਠਨਬਤ defects in accord with applicable Sherwin-Williams quality control procedures.
The information and recommendations set forth in this Product Data Sheet are Liability for products proven defective, if any, is limited to replacement of the de-
based upon tests conducted by or on behalf of The Sherwin-Williams Company. fective product or the refund of the purchase price paid for the defective product
Such information and recommendations set forth herein are subject to change and as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
pertain to the product offered at the time of publication. Consult your Sherwin- OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
Williams representative to obtain the most recent Product Data Information and STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
Application Bulletin. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
www.sherwin-williams.com/protective