Professional Documents
Culture Documents
Operating Instructions g500-B Bevel Gearboxes ATEX g500 Gearboxes EN
Operating Instructions g500-B Bevel Gearboxes ATEX g500 Gearboxes EN
ATEX−g500
B45 ... B4300
H45 ... H3000
S130 ... S4500
Operating Instructions EN
Gearboxes
Ä.[qGä
.[qG
l
, Please read these instructions before you start working!
Follow the safety instructions enclosed.
0Abb. 0Tab. 0
Contents i
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Application as directed ................................................ 8
2.3 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4 General requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5 General safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1.1 Gearbox / geared motor product code . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 Short overview of the new mounting positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2.1 Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Mechanical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3 Ambient conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.4 Installation / mounting condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.5 Mounting of input and output elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.5.1 Mounting with belt pulleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.6 Information on gearboxes with shrink disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.6.1 Shrink disc and hollow shaft cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.7 Shaft sealing rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.8 Lubricants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.9 Roller bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.10 Mounting of motors on gearboxes with mounting flange . . . . . . . . . . . . . . . . . . . 21
5 Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.1 Motor connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6 Commissioning ............................................................... 26
6.1 Checklist for commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.2 Measurement of surface temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.3 Surface temperature limits for temperature class T4 in area 1 and 2 . . . . . . . . . . . 28
6.4 Measurement of oil temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.1 Maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.1.1 Periodic inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.1.2 Inspection to be made only in area 1 and/or 21 . . . . . . . . . . . . . . . . . . . . 30
7.2 Maintenance and repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.3 Lubricant table for ATEX geared motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.3.1 Lubricate roller bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.4 How to check for oil leakages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.4.1 Oil level check for gearboxes (geared motors) . . . . . . . . . . . . . . . . . . . . . . 35
7.5 Check intervals for clutches in potentially explosive atmospheres . . . . . . . . . . . . . 41
7.5.1 Wear and backlash check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8 EU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Contents
¯ This documentation serves for safety−relevant operations on and with the
gearboxes. It contains safety instructions which must be observed.
¯ All personnel working on and with the gearboxes must have the documentation
available during the work and observe the information and notes relevant for
them.
¯ The documentation must always be complete and in a perfectly readable state.
I Tip!
Information and tools concerning the Lenze products can be found in the
download area at
www.lenze.com
Validity
These instructions apply to the following gearbox types:
Type Type code Name
g500−B45 ... B4300 g50BB111 ... g50BB243 Bevel gearbox
g500−H45 ... H3000 g50BH110 ... g50BH230 Helical gearbox
g500−S130 ... S4500 g50BS133 ... g50BS245 Shaft−mounted helical gearbox
Target group
This documentation is directed at qualified skilled personnel according to IEC 60364.
Qualified skilled personnel are persons who have the required qualifications to carry out
all activities involved in installing, mounting, commissioning, and operating the
product.
Drive system Drive systems with g500 gearboxes and other Lenze drive
components
The following pictographs and signal words are used in this documentation to indicate
dangers and important information:
Safety instructions
Layout of the safety instructions:
} Danger!
(characterises the type and severity of danger)
Note
(describes the danger and gives information about how to prevent
dangerous situations)
{
voltage
Danger! Reference to an imminent danger that may result in death
or serious personal injury if the corresponding measures are
not taken.
Danger of personal injury through a general source of
}
danger
Danger! Reference to an imminent danger that may result in death
or serious personal injury if the corresponding measures are
not taken.
(
Danger of property damage
Stop! Reference to a possible danger that may result in property
damage if the corresponding measures are not taken.
Application notes
2 Safety instructions
¯ These operating instructions only apply in connection with the g500−B / g500−H /
g500−S mounting instructions!
¯ Observe operating instructions for devices with individual ignition protection, e.g.
motor!
¯ If the data are inconsistent, these operating instructions have priority.
¯ Pay attention to an installation according to EMC, especially for frequency inverter
operation!
For the evaluation of the product, the following versions of the standards are taken
into account:
¯ EN ISO 80079−36:2016
¯ EN ISO 80079−37:2016
¯ TRGS 727:2016
The gearboxes / geared motors are intended for use in machinery and systems and
may only be used in accordance with these operating instructions, the nameplate
and the text of the order confirmation. They correspond to existing standards and
regulations and meet the requirements of EU directive 2014/34/EU.
Explosive gas, fog, vapour, or dust atmospheres can cause severe injuries or death
when getting in contact with hot and / or sparking parts of the geared motor.
All operations concerning mounting, connection, commissioning as well as
maintenance and repairs on the gearbox /geared motor and the electrical
supplementary equipment must only be carried out by qualified personnel!
¯ For installation, observe EN 60079−14 for locations with potentially explosive
atmospheres!
) Note!
Observe nameplate data with regard to the category and explosion
group!
2.3 Disposal
The gearboxes/geared motors have been designed for industrial applications. Any
other use is improper use.
¯ To ensure safe operation, the gearboxes/geared motors are only to be used in
accordance with the information in the operating instructions and the technical
data sheet. During use, the required legal and safety instructions for the
respective application are also to be observed. This also applies analogously to the
use of accessories.
¯ We cannot be held liable if the notes specified in this extract are not observed or
in the event of improper handling of the product. Furthermore, the warranty for
products and spare parts shall be considered null and void.
¯ The products are not safety elements in the context of the intended use.
The gearboxes/geared motors correspond to the state of the art and are safe to operate.
The product may be a source of residual hazards if it is used and operated improperly by
untrained personnel.
Every person commissioned with the installation, commissioning, maintenance, or
repair of the gearboxes/geared motors must have read and understood the customer
documentation and, in particular, the safety−related notes.
¯ When selecting and operating a product, comply with generally accepted
engineering rules.
– All connected electrical and mechanical equipment must be suitable for the
respective application.
¯ Observe the notes in these operating instructions as well as the operating
conditions and permissible data specified on the labels/nameplates of the
respective products.
– Ensure that only the types of protection for products corresponding to the
respective zones are installed!
– The product is only approved for proper and intended use in normal industrial
atmospheres.
– Ensure that no falling objects can strike the products. In connection with rust,
light metals, and kinetic energy, an exothermic ignitable reaction may be
triggered.
– The operator is to ensure lightning protection for the entire system in
compliance with local regulations.
¯ Note that live conductors must never be disconnected! This may result in danger
to life if an explosive atmosphere is present at that point in time.
¯ Take suitable measures to rule out impermissible interferences.
¯ The surface on which the products are mounted must be load−bearing and clean.
¯ The gearboxes/geared motors (surface) and the connecting cable must not be
damaged.
¯ All cables must be laid such that they are protected against external mechanical
influences.
¯ Electrical cables/equipment must only be installed by a qualified electrician and
must fulfil the requirements of any additional applicable standards (e.g. EN
60079−14).
¯ The manufacturer of the motors should be informed of the issue of "Shaft
voltages in frequency inverter mode"; in his operating instruction, the operation
of the motors with frequency inverters must be explicitly permitted. The shaft
voltages generate significant currents which irreparably damage the ball bearings
in standard machines. This situation can only be remedied by using ceramic balls
in the bearings (expensive variant) or by using insulated bearings (simpler
variant).
¯ Ventilation equipment is to be kept free and clear.
¯ Simple electrical equipment may be installed in mounting boxes; they may be
used in intrinsically safe electric circuits. In all cases, the manufacturer is to draft a
control drawing for this purpose (proof of intrinsic safety) and attach it to the
delivery documents.
¯ When assembling the motor and gearbox (except for products which are delivered
by the manufacturer in an already combined fashion), the permissible angle error
is to be observed.
¯ Ensure that the air velocity of the fans in dusty atmospheres does not exceed a
value of 20 m/sec.
3 Product description
3.1 Identification
ATEX classification
Example R II 2 G Ex h IIB T3
Meaning Variant ATEX classification
Classification Explosion protection symbol R
Device group Above−ground use II
Category Zone 1, 21 2
Zone 2, 22 3
Drive design Explosive atmosphere caused by gas G
Explosive atmosphere caused by dust D
Ignition protection Constructional safety/liquid immersion Ex h
type
Explosion group:
Areas exposed to High ignition power required IIA
gases Medium ignition power required IIB
Low ignition power required IIC
Exposed to dust Lint IIIA
Non−conductive dust IIIB
Conductive dust IIIC
Temperature £450°C T1
class/temperature £ 300°C T2
limits for the zones £ 200°C T3
£ 135°C T4
£ 100°C T5
£85°C T6
M1[A] M1[A]
M5[F]
M4[C]
M4 M4[C] M5[E]
M3[B]
M3[B]
3.2.1 Nameplate
L 1 15
42 6
5.1 7.2 28
5.2 5.3/5.4 38 1)
10.1 39.4 5.11
39.5 18 39.7
39.6 10.2/10.3
40 11
GT−ATEX−001.des
1) Data only for gearboxes with a motor
Pos. Contents
1 Manufacturer / production location
5 Technical data
5 5.1 Ratio
5 5.2 Rated torque
5 5.3 Rated speed
5 5.4 Rated frequency
5 5.11 Maximum input speed
6 Mounting position / position of the system blocks
7 Lubricant details
7 7.2 Lubricant type
10 Production data
10 10.1 Order number
10 10.2 Material number
10 10.3 Serial number
11 Bar code
15 Applicable conformities, approvals and certificates
18 Year of manufacture / week of manufacture
28 Degree of protection of the gearbox / geared motor
38 Load capacity
39 ATEX details on the gearbox
39.4 ATEX temperature range (only specified if deviating from −20 °C ... +40 °C)
39.5 Explosion protection specification for gas
39.6 Explosion protection specification for dust
39.7 ATEX file number
40 Additional data
42 Gearbox/geared motor type
4 Mechanical installation
4.2 Preparation
¯ It must be checked that the data given on the nameplate of the gearbox/motor
and in the order confirmation text comply with the permissible explosion−proof
application conditions on site:
– Explosion group
– Category
– Zone
– Temperature class
– Maximum surface temperature
¯ Mount the gearbox only in the mounting position indicated on the nameplate!
¯ The max. input speed and the max. rated torque given on the nameplate must not
be exceeded!
¯ The application limits for temperature class T4 (gas Ex) and T125 °C (dust Ex) are
specified in the chapter 6.3 "Surface temperature limit". In particular, for input
speeds <200 rpm, a consultation with Lenze is required.
¯ The application of the gearboxes is only permissible at an ambient temperature of
−20 °C to +40 °C unless the nameplate bears another temperature.
Tighten all screw connections with the torques given and lock them with standard
screw locking adhesive!
Thread
M3 M4 M5 M6 M8 M10 M12 M16 M20 M24 M27 M30 M36
Strength Tightening torque [Nm]
4.8 0.7 1.4 2.8 4.8 12 23 − − − − − − −
8.8 1.3 3.0 5.9 10.1 24.6 48 84 206 415 714 1050 1428 2482
10.9 1.9 4.6 8.6 14.9 36.1 71 123 302 592 1017 1496 2033 3535
Tab. 1 Tightening torques for friction factor m = 0.12; tolerance of the tightening torque ±10 %
Please note: increase the tightening torque by 10% for screwed connections with flat
gaskets.
} Danger!
The installation of the gearbox onto/into the customer machine must be
made in such a way that no clearances may develop where dust can
deposit which may come into contact with moving parts (risk of heat
development).
The gearboxes are filled in the factory with the required quantity of oil.
} Danger!
¯ A change in mounting position may only be carried out after
consultation with Lenze. The ATEX approval no longer applies when
Lenze is not consulted!
¯ Parts of the gearbox can be made of aluminium and must be protected
against external shocks in order to prevent shock sparks!
¯ The gearboxes/geared motors must not be used in systems with
cathodic protection!
¯ The gearboxes and motors must be included in the equipotential
bonding of the system.
¯ Placing an installation above hot parts on which, for instance, leaking
oil may ignite is not permissible. If required, install an oil collecting
trough.
¯ For use in the areas of explosion group IIC, the total thickness of all
paint layers must not exceed 0.18 mm. For explosion group IIB, the
maximum is 1.5 mm.
Only suitable input and output elements must be used for the application in areas with
increased danger of explosion!
The applicability can be proven by:
A an own ATEX approval or
B a standardised evaluation of the danger of ignition.
Mount transmission elements only by means of a pusher tool and / or the tapped
centre hole at the end of the shaft.
The forces of the transmission elements must not exceed the permissible radial and
axial forces.
} Danger!
¯ Avoid blows and impacts on the shaft at all costs. Damages could
result at the roller bearing, housing and shaft.
¯ Tighten all screw connections with the torques given and lock them
with standard screw locking adhesive!
¯ The assembly of the single components tested by ATEX must be
checked for new ignition danger.
In the case of belt pulleys, the correct tension of the belt specified by the manufacturer
must be observed, in order to prevent the belt from slipping, which entails an increase
in temperature.
} Danger!
Belt drives are permissible in potentially explosive atmospheres under
the following conditions.
¯ The belt drive is only to be outfitted with conductive belts in
accordance with TRGS 727.
¯ The belt drive is equipped with a pre−tensioning device.
¯ The belt drive is designed for at least 50 K above the maximum
ambient temperature.
¯ The supporting frames and/or connections with the belt drive are only
to be operated when earthed.
¯ The power of the transmission, the maximum belt speed, the correct
belt tension range and how it is measured, and the alignment
tolerance are defined in the original operating instructions.
¯ In explosion group IIC, no belt drives are permissible in category 2!
¯ Approval is only given in explosion groups IIA/IIB for circumferential
belt speeds of 30 m/s.
} Danger!
All screw connections must be locked with standard screw locking
adhesive!
} Danger!
Stainless steel connections must be checked by Lenze due to the modified
friction factors.
It is absolutely necessary to ensure that the shrink disc is mounted correctly (, g500−B
/−S mounting instructions). A shrink disc connection that is not mounted correctly may
slip, and the heat generated in this process may produce a potential ignition source.
The maximum permissible torques of shrink disc connections must not be exceeded!
Observe the following table.
} Danger!
The torque values in Tab. 2 apply to a true torque stress. If a radial or axial
force is at work, it is necessary to consult Lenze.
} Danger!
If the cover is supplied with a seal, it must be installed to prevent the
ingress of dust.
After mounting the cover it must be ensured by means of a test run that the shrink disc
or the plugged−in machine shaft does not rub against the cover.
The cover must be protected against impact and falling objects using suitable measures.
Any attached protective devices must be electrically conductive and integrated in the
equipotential bonding.
If the cover is damaged, the cover and seal must be replaced to avoid ingress of dust. The
dispersion of dust which might have ingressed must be prevented. Thus, if ingress of
dust is suspected, the shrink disc cover must be removed and cleaned according to the
local conditions. Covers that are no longer firmly seated must be replaced by new ones.
) Note!
If the site contains material that might affect elastomer materials, the
stability of the shaft sealing rings with regard to the material has to be
inspected.
For this, please consult Lenze.
Lenze uses shaft sealing rings of fluoro rubber (FKM) or acrylonitrile
butadiene rubber (NBR).
Shaft sealing rings seal the gap between the housing and the rotating shafts. These are
wearing parts whose replacement is required after reaching the wear limit.
In the case of abrasive environmental conditions, protect shaft sealing rings against
contact with the abrasive material.
The service life of shaft sealing rings is influenced by many parameters including the
following:
¯ Circumferential speed at the sealing lip
¯ Temperature
¯ Internal pressure in the gearbox
¯ Lubricant viscosity
¯ Chemical composition and additivation of lubricants
¯ Installation (lubricant supply of the sealing lip)
¯ Particles or metallic abrasion in the lubricant
¯ Material of shaft sealing ring
Due to this multitude of influencing parameters, without tests that are tailored to
the application it is almost impossible to make an exact statement with regard to the
service life. Since the service life of the shaft sealing rings is subject to the variations
described above, regular inspections are absolutely required. This is the only way of
avoiding an unnoticed loss of lubricant in the gearbox (time intervals (¶ 29).
During the renewal of the shaft sealing ring, the condition of the sealing lip contact
areas on the shaft must also be checked. If grooves are noticeable, the shaft must be
serviced or replaced. Alternatively, the shaft sealing ring can be mounted slightly
moved in axial direction so that the sealing lip runs on a new location.
4.8 Lubricants
} Danger!
¯ The lubricant must be changed at defined intervals (¶ 29).
¯ The gearbox must be inspected for leakage at regular intervals!
The roller bearings in the gearboxes also have a finite service life under perfect
operating conditions. This so−called fatigue life is a purely statistical value for roller
bearings. The actual service life that a single bearing reaches may differ greatly. For
this reason, a regular inspection and/or monitoring of the roller bearings is necessary.
The following measurements are carried out for monitoring:
¯ Running noises
¯ Temperature
¯ Vibration diagnosis
¯ Frequency analysis
A combination of several measurements is frequently applied. During the
measurements, the periodic change is generally checked, i.e. reference values are
determined after a short run−in period and compared with the subsequent
measurements. This allows for determining changes in the operational performance
that point to a forthcoming loss or a necessary maintenance.
The roller bearing industry offers appropriate devices for monitoring (e.g. from SKF or
FAG). The roller bearing industry also offers the possibility of having their experts
perform the monitoring. Please contact the roller bearing industry concerning an
appropriate measure for your specific situation.
) Note!
In order to make it easier to assess at which point in time a preventive
replacement is advisable, a calculation should be carried out at Lenze if
the precise operating conditions are known. This recalculation makes it
possible to provide recommendations with regard to the changing
intervals of the roller bearings.
( Stop!
¯ In frequency inverter operation, the motor must be provided with a
corresponding ATEX approval.
¯ In frequency inverter operation in explosion group IIC, stray currents
must be ruled out, since very low stray currents are already potentially
explosive.
¯ Operation of the gearbox must be permissible for all working points! If
required, consult Lenze.
) Note!
The IP enclosure specified may be only obtained by mounting a motor to
the mounting flange.
¯ The motor flange must fully cover the access to the interior of the bearing
flange/adapter and prevent the ingress of dust and liquids. Use a suitable surface
sealing compound on the contact area of the motor flange and bearing flange for
sealing purposes.
¯ Mount coupling hub on the motor side, , documentation for the respective
gearbox.
¯ Lock screws at the clutch hubs with adhesive for medium−strength screw locking.
¯ Tighten all screw connections with the torques given and lock them with
standard screw locking adhesive!
¯ Clamping hubs must only be used together with a featherkey, otherwise the hubs
may slip in the event of sudden torque changes!
¯ Check the clutch in the prescribed maintenance intervals.
¯ Observe maximum permissible load at the mounting flange according to the
mounting instructions.
5 Electrical installation
) Note!
Please observe the operating instructions for the explosion−protected
motor!
{ Danger!
Hazardous electrical voltage
The electrical installation has to be carried out by skilled personnel in
compliance with electrotechnical regulations and standards.
( Stop!
¯ In frequency inverter operation, the motor must be provided with a
corresponding ATEX approval for frequency inverter operation.
¯ In frequency inverter operation in explosion group IIC, stray currents
must be ruled out, since very low stray currents are already potentially
explosive.
The manufacturer of the motors must grant approval for frequency inverter mode. Only
flameproof motors are permitted in this case!
The N−end bearing of the motors must be outfitted with an insulated bearing.
¯ Exceptions are permissible for flameproof motors IF an insulating coupling is used
at the motor shaft; this is the case for Lenze ATEX gearboxes / geared motors with
bearing flange with jaw coupling.
¯ Alternatives:
– The installing party evaluates the influence of the vagrant currents under its
own responsibility.
– Note: For smaller motors up to approx. 6 kW and an impedance < 10 M
between the drive end and N−end bearing, dangerous external vagrant currents
are generally not to be expected.
The gearboxes/geared motors are to be installed in a higher−level system. Depending
on the degree of protection, the time for the cleaning of the equipment (dust
deposits) is to be defined. It must be ensured that only the types of protection for the
device which correspond to the zones/categories are installed! During installation,
the valid national installation regulations, e.g. EN 60079−14 must be observed.
Important facts
¯ In zone 1 and/or zone 2 (category 2G; EPL Gb and 3G; EPL Gc) and zone 21
(category 2D; EPL Db) and/or Zone 22 (category 3D; EPL Dc) − be sure to observe
restrictions indicated on the nameplate and/or the accompanying
documentation! − the product is only to be put into operation by specialists with a
qualification similar to a qualified person pursuant to TRBS 1203. The category 2
gearboxes can be combined with category 3 drives; however, they will then only
be usable in the associated zone.
– When doing so, the information on the nameplate and in the order
confirmation must be observed.
– Observe the notes in these operating instructions as well as the operating
conditions and permissible data specified on the labels/nameplates of the
respective products.
¯ The gearboxes/geared motors may only be used in conventional industrial
atmospheres. If aggressive substances are present in the air, Lenze must always be
consulted first.
– The operation of the product is only permissible in a completely assembled and
intact state. In the event of any possible leaks in the system, the operator must
note the possibility of any changes in zone classification caused by this.
– The ambient conditions specified in the operating instructions must always be
observed and protected accordingly against adverse ambient conditions. Heat
radiation from foreign products/components are also to be taken into account.
– Some components may be made of light metals. These must be protected
against external impacts.
– The gearboxes/geared motors are to be protected against the impermissible
ingress of liquids and/or pollution.
6 Commissioning
( Stop!
The drive must not be commissioned until everything is checked and
answered with "yes"!
During commissioning
} Danger!
If the temperature is higher than the value given, the drive must
immediately be stopped and Lenze must be contacted!
Since the application and installation conditions for the geared motors can differ
significantly, it must be ensured that a maximum temperature of 135°C is not
exceeded in the gearbox, even under adverse conditions. The maximum temperature
measured at the housing in chap. 6.2 must not exceed the values listed in the
following tables.
) Note!
Mounting position M2[D] does not permit input speeds higher than
1500 rpm due to the high stress on the shaft sealing ring!
The oil temperature is measured in the lower area of the gearbox (on the level of the oil
sump). In the case of gearboxes with an oil drain plug, the temperature must be
measured on the oil drain plug. 10 K are added to the temperature measured and, on
the basis of the diagram (¶ 32), the lubricant change (¶ 29)is determined.
7 Maintenance
} Danger!
If there are unusual operating noises, vibrations, or increased
temperatures in the gearboxes/geared motors during or between the
prescribed checks, the geared motor must be stopped immediately and
maintenance work must be performed!
The guidelines and standards as for instance the
"berufsgenossenschaftliche Vorschriften, BGV A2" (guidelines of German
Professional Associations), operating instructions (EN 50110) and the
instructions for installation (EN 60079−14 and EN 50281−1−2) and
maintenance (EN 60079−17) must always be observed!
Plastic parts must be damp−cleaned only to prevent electrostatic charge.
Visual inspection
Inspection which identifies, without the use of access equipment or tools, those
defects, such as missing bolts, which will be apparent to the eye.
Close inspection
Inspection which encompasses those aspects covered by a visual inspection and, in
addition, identifies those defects, such as loose bolts, which will be apparent only by the
use of access equipment, for example steps, and tools.
Detailed inspection
Inspection which comprises those aspects covered by a close inspection and, in
addition, identifies those defects, such as loose terminations, which will only be
apparent by opening the enclosure, and/or using tools and test equipment, where
necessary.
Inspection
Action comprising careful scrutiny of an item carried out either without dismantling or
with the addition of partial dismantling as required, supplemented by means such as
a measurement, in order to arrive at a reliable conclusion as to the condition of an item.
} Danger!
The maintenance intervals must be adhered to for safe operation with
respect to explosion protection!
Non−adherence to the maintenance intervals voids the EU Declaration of
Conformity!
Maintenance measures involving disassembly of the machine are only to
be performed in/upon the absence of potentially explosive atmospheres.
For use in zone 2 or 22 and mounting positions M1[A], M3[B], M4[C], M6[E] and
M5[F] ( , "Adjustment made easy" documentation; see Lenze homepage) the
following specified time intervals can be doubled for close and detailed inspections.
If the checks show any irregularities or items of damage, the cause has to be
determined immediately and the damage has to be repaired.
( Stop!
A check with regard to leakage, unusual operating noises, vibrations, and
impermissibly high temperatures is to be additionally performed within
the first days after commissioning.
Type of inspection
Visual Close Detailed
Inspection to be carried out within the time interval of operating hours: 100 h 500 h 3000 h
But at the latest: Once a week 3 months 6 months
Actions
Visual inspection of the geared motor.
Check rubber buffer of the torque arm and replace it in the event of visible wear or
damage.
Check mounting of the gearbox (foot, flange and shrink disk mounting).
Inspections of the electric motors As specified in the operating instructions for
the motor
Type of inspection
Visual
Inspection to be carried out once after: 2000 h
Not later than after: 3 months
Actions
Visual inspection and backlash check of the elastic ring gear, ^ 41. ·
} Danger!
Maintenance or repair operations under ex conditions are not
permissible!
The repair work of explosion−protected electrical machines must only be
performed by the manufacturer or qualified personnel, in compliance
with the Ordinance for Industrial Safety and Health, in a workshop
equipped for these tasks. Only use the respective original spare parts
from Lenze. The operating steps must be performed in accordance with
the instructions given by the manufacturer.
Equipment which has been changed or repaired at parts that guarantee
explosion protection must only be started again if a qualified person in
accordance with the Ordinance for Industrial Safety and Health has
confirmed the compliance with the valid technical regulations.
Type of inspection
Maintenance/repair
Maintenance/repair to be made in the time Acc. to diagram 1) Immediately if
interval of operating hours: any irregularities are detected
during monitoring, or as a
preventive measure after a
calculated changing interval 2)
But at the latest after: 3 years −−−
Actions
Change oil
Replace shaft seals, check condition of sealing
lip contact area and repair it, if necessary.
Replace roller bearing grease ·
For gearboxes with ventilation − replace
breather element.
Check of state of all gearbox parts −
replacement in the case of damage.
Replacement of roller bearings
·
Maintenance of the electric motors used According to company’s own operating instructions
1) Determination of the period by means of temperature measurement, ^ 28and using
the oil change diagram.
2) For better assessment of the roller bearing changing interval, a calculation taking the
real operating conditions into consideration should be carried out at Lenze, ^ 20
) Note!
Since it is not possible to reliably calculate the service life of an individual
roller bearing (¶ 20), it is absolutely essential that the roller bearings are
checked at regular intervals. A difference in the noise or vibration
response or rising temperatures indicate the immediate necessity for
replacing the bearings.
) Note!
An oil analysis presents a more detailed procedure for determining the
necessity of an oil change, analysing the state of the gearbox oil on the
basis of an oil sample.
25000 CLP PG
CLP HC / HC USDA H1
20000 CLP
15000
[A] h
10000
5000
0
70 80 90 100 110
[B] °C
Fig. 2 "Lubricant change" diagram
0 Operating hours
1 Oil temperature
The lubricants listed in the following table are approved for Lenze ATEX gearboxes.
Ambient temperature [°C] DIN 51517−3: CLP Gearbox type
ISO 12925−1: g500−B/ −H / −S
−50 0 +50 CKC/CKD
Omala S4 GX 320
−25 +50 3) CLP HC VG 320
Omala S4 GXV 320
For the lubricant selection observe the following legend relating to the lubricant
table!
CLP PG Þ Polyglycol oil
CLP HC Þ Synthetic hydrocarbons or poly−alpha−olefin oil
1) Þ Currently no test results are provided yet for the efficiency of the specified lubricants for worm gearbox lubrication. If
these oils are used, the permissible torque must be reduced to 80% of the catalogue values.
2) Þ Polyglycol oils cannot be mixed with other types of oil
3) Þ For ambient temperatures above 40°C please consult us and specify the exact operating conditions!
4) Þ Observe critical starting performance at low temperatures! At temperatures below −20 °C, special measures must be
implemented! In this case, contact Lenze!
Þ Low−temperature oils, observe critical starting performance at low temperatures!
For regreasing the roller bearings and lubricating the shaft sealing lip in the Lenze ATEX
gearboxes with an ambient temperature range of −30°C to + 50°C use the following
lubricant: Klüber Petamo 133N.
The operator must check the gearboxes and geared motors for oil leakages according
to the maintenance intervals given in chapter 7.1 et seqq..
A visual inspection for leakages must be performed on the complete gearbox /
geared motor. A lubricant leakage can be recognised, for example, by means of flow
traces on the gearbox / geared motor, drop formation and/or lubricant spots under
the gearbox / geared motor.
The occurrence of a leakage can usually be expected at the shaft sealing rings. Other
possible locations include the parting lines between housing components, flanges,
covers, caps and similar.
Gearboxes with a mounting flange for IEC standard motors are provided with a
leakage check bore hole in order to be able to detect leakages of the drive shaft
sealing ring at an early stage. The position of the bore hole depends on the mounting
position ordered.
2
Fig. 3 GNA standard motor flange; position of the leakage check bore hole
For every leakage test, the screw plug (item 2) in the bearing flange must be removed
and checked whether leakage oil can be found behind the screw. Afterwards, the bore
must be closed again.
If a leakage is detected, the lubricant filling level in the gearbox must be checked
immediately and, if necessary, adjusted to the prescribed value.
¯ If the leakage quantity consists of only a few drops of lubricant, continued
operation is possible. However, continued operation presupposes that a more
frequent monitoring must take place to rule out an unnoticed increase of leakage
amount. Short−term plans for a repair to stop the leakage must be made.
¯ With higher leakage quantities the leakage must be repaired immediately.
During the replacement of the shaft sealing ring, the condition of the sealing lip
contact areas on the shaft must also be checked. If grooves are noticeable, the shaft
must be serviced or replaced. Alternatively, the shaft sealing ring can be mounted
slightly moved in axial direction so that the sealing lip runs on a new location.
For gearboxes (geared motors) that are used in zone 1 or 21, a check of the oil level is
required in addition to a check for oil leakage. The check must be performed before the
initial commissioning and subsequently at regular intervals (¶ 29).
For the G50BB111, G50BB124, G50BH110, and G50BH114gearbox types, the mounting
cover must be removed to perform the lubricant check.
The remaining gearboxes are equipped with one or several oil−level plugs. Depending on
the oil−level inspection device used, the oil−level inspection must be performed as
follows.
7.4.1.1 Inspection of gearboxes with cast iron housing and oil−level plugs
¯ from g500−B600 / G50BB160
¯ from g500−H600 / G50BH160
¯ from g500−S950 / G50BS195
) Note!
Deviating oil level must be corrected.
The data of the filled in oil is given on the nameplate. Only use the same
oil as already contained in the gearbox.
Observe the approved oil manufacturer’s oil types. (¶ 33)
1. Disconnect the geared motor from the mains and protect it from unintentional
switch−on.
2. Wait a few minutes until all of the oil has accumulated in the oil sump.
3. Determine position of the oil−level plug. The position of the oil−level bores is
indicated in the respective standard mounting instructions for the gearbox types
in the "Maintenance" chapter.
4. Remove oil−level plug.
5. Oil−level inspection.
– Max. oil level: bottom edge of oil−level bore
– Min. oil level: X mm below bottom edge of oil−level bore (see Fig. 4 and Tab. 5).
6. If necessary, correct oil level to the correct value. Use the same oil grade as the one
already in the gearbox.
7. Close oil−level bore again; for tightening torque of the screw see Tab. 6.
0
1
x
90
Oil
Tab. 5
) Note!
Deviating oil level must be corrected.
The data of the filled in oil is given on the nameplate. Only use the same
oil as already contained in the gearbox.
Observe the approved oil manufacturer’s oil types. (¶ 33)
1. Disconnect the geared motor from the mains and protect it from unintentional
switch−on.
2. Wait a few minutes until all of the oil has accumulated in the oil sump.
3. Determine position of the oil−level plug. The position of the oil−level bores can be
gathered from the respective standard mounting instructions for the g500
gearbox types in the "Maintenance" chapter.
4. Remove oil−level plug.
5. Check oil level using dipsticks that are to be manufactured depending on the
mounting position. The dipsticks are shown in the standard mounting
instructions for the g500 gearbox types in the "Maintenance" chapter.
– The oil level must be within the marked area on the dipstick.
6. If necessary, correct oil level to the correct value. Use the same oil grade as the one
already in the gearbox.
7. Close oil−level bore again; for tightening torque of the screw see Tab. 6.
g500−B−xxx
7.4.1.3 How to check the oil level of gearboxes without oil−level plugs
For the G50BB111, G50BB124, G50BH110, and G50BH114gearbox types, the mounting
cover must be removed to perform the lubricant check.
} Danger!
The following steps must not be executed under explosive conditions!
Preparation
¯ Ensure standstill of the drive system and prevent any machine movement.
¯ Disconnect the geared motor from the mains and protect it from unintentional
switch−on.
¯ The gearbox must have cooled down.
Dismounting
1. Bring the gearbox into mounting position A so that the mounting cover is located
on the top side. The installation surface must be even and level.
g50BH
xxx
g50BB
xxx
Check
Use a level gauge to measure the distance X from the housing sealing surface to the oil
level, holding the gauge at right angles to the sealing surface.
Use the following table to determine the height of the setpoint oil level T on the basis
of the gearbox/geared motor type and the mounting position during operation.
Housing types AK / AL / AR / BR − gearbox housing with foot
Mounting position Distance T [mm]
g50BH110 g50BH114 g50BB111 g50BB124
H100 − foot H140 − foot B110 B240
M1[A] 2−stufig 49 61 54 74
M1[A] 3−stufig −−−−− −−−−− −−−−− 48
M3[B] 16 15 15 24
M4[C] 26 37 * 3
M2[D] 16 15 22 30
M5[F] 49 48 −−−−− −−−−−
M6[E] 26 26 −−−−− −−−−−
M5[E] −−−−− −−−−− 29 19
M6[F] −−−−− −−−−− 41 42
* Oil−level inspection B110 in mounting position C
The difference between table value T and the measured distance X must be between 0.0
and 3.0 mm; 0.0 < (T−X) < 3.0 mm.
If the oil level deviates from this range of values, it must be corrected!
Use the same oil for this as is already filled in the gearbox, see nameplate data. The oil
manufacturers’ approved lubricant types can be found in the lubricant table, (¶ 33).
Mounting
1. Check the sealing surfaces of the housing and cover as well as the gasket for
damage. Damaged parts must be replaced.
2. Then mount the seal, cover, and screws, paying special attention to the correct
position and arrangement of the seal.
The tightening torque of the M6 screws is 10 Nm ± 10%. It may be required to
tighten the screws several times until the torque is achieved at all screws.
3. Bring the gearbox back to the original operation mounting position. Correct
mechanical fixing and a professionally implemented electrical connection must
be ensured.
) Note!
Leakage check: monitor the gearbox in the next days in order to make
sure that it is sealed.
If no or only negligible wear of the ring gear is detected at this first inspection,
further inspection intervals can be carried out after every 6000 operating hours,
after 18 months at the latest, provided that the same operating parameters are
II 2G Ex h IIB T4
applied.
If there is an increased wear after the first inspection calling for a replace of the
ring gear, the cause must be detected.
If no or only negligible wear of the ring gear is detected at this first inspection,
further inspection intervals can be carried out after every 4000 operating hours,
after 12 months at the latest, provided that the same operating parameters are
II 2G Ex h IIC T4
applied.
If there is an increased wear after the first inspection calling for a replace of the
ring gear, the cause must be detected.
( Stop!
When the wear limit of max. abrasion is reached (¶ 42) the ring gear
must be replaced immediately!
Fig. 6 GNA standard motor with flange; position of the locking screw (1)
1. Remove the screw plug (item 1) for the wear and backlash check.
2. Check the clearance between clutch hub and elastic ring gear with a feeler gauge
(Fig. 7).
3. If the wear limit Xmax." (Tab. 8) is exceeded, the ring gear must be replaced. If the
hub shows damages, the complete clutch must be replaced.
4. After performing the test, the opening (item 1) must be closed again with the
screw plug.
A E
D F
Û
Lenze Service GmbH
Breslauer Straße 3, D−32699 Extertal
Germany
Ü 0080002446877 (24 h helpline)
Ø +49515482−1112
Ù [email protected]
10 9 8 7 6 5 4 3 2 1