Professional Documents
Culture Documents
Atenna Basics
Atenna Basics
Antenna Basics
Antenna Fundamentals
Lets get right down to the study of antennas and Antenna Basics. Suppose one day you're walking down
the street and a kind but impatient person runs up and asks you to design an antenna for them. "Sure",
you quickly reply, adding "what is the desired frequency, gain, bandwidth, impedance, and polarization?"
Or perhaps you have never heard of (or are a little rusty) on the above parameters. Well then, you've come
to the right place. Before we can design an antenna or discuss antenna types, we must understand the
basics of antennas, which are the fundamental parameters that characterize an antenna.
So let us learn something. We'll start with frequency and step through radiation patterns, directivity
and gain, and ultimately close with an explanation on why antennas radiate. Jump ahead if this is
already familiar to you.
Frequency
The basics of sinusoids (sine and cosine waves), wavelength, frequency and the speed of light.
Frequency Bands
No discussion on antenna fundamentals is complete without a real-world list of frequency bands.
Radiation Pattern
The radiation pattern for an antenna is defined on this page. We have 3D graphs of real antenna
radiation patterns, with a discussion on isotropic, omnidirectional and directional radiation
patterns. Radiation patterns are of the utmost importance in the discussion of antenna basics.
Field Regions
http://www.antenna-theory.com/basics/main.html (1 of 4) [2/28/2013 12:32:33 PM]
Antenna Basics
The introduction to antennas continues with a discussion of Field Regions. The Far Field, Near Field
and Fresnel Regions for an antenna is presented.
Directivity
Directivity is fundamental to antennas. It is a measure of how "directional" an antenna's radiation pattern is.
Impedance
Antenna Impedance is presented as the ratio of voltage to current at the antenna's terminals. Low- and
High-Frequency models are presented for transmission lines. The fundamentals of antenna theory
requires that the antenna be "impedance matched" to the transmission line or the antenna will not
radiate. The concept of VSWR is introduced as a measure of how well matched an antenna is.
Bandwidth
The bandwidth of an antenna is the frequency range over which the antenna radiates. The bandwidth can
be defined in different ways; this page presents an introduction to antenna bandwidth.
Polarization of Waves
All electromagnetic plane waves have an associated polarization. The antenna concepts of Linear,
Circular and elliptical polarization are presented.
Polarization of Antennas
Antennas are also classified by their polarization; this defines the type of plane wave polarization
the antenna is most sensitive to. This is a fundamental antenna concept.
Effective Aperture
http://www.antenna-theory.com/basics/main.html (2 of 4) [2/28/2013 12:32:33 PM]
Antenna Basics
Effective aperture is a basic antenna concept that is a measure of the power captured by an antenna from
a plane wave. Effective aperture can be expressed as a function of the antenna gain and the wavelength
of interest.
Antenna Temperature
Antenna Temperature is a property of an antenna and the environment it operates in. It is a measure of
the noise received by the antenna due to thermal (or temperature) effects.
After concluding the study of Antenna Fundamentals, the next step in the
understanding of antenna theory is to move on to the types of antennas page, where
basic antenna types are discussed. You will find that the understanding of the
above concepts is crucial for understanding real antennas.
Antennas (Home)
Like this page and want to support the site? Link to this antenna fundamentals page, cut and paste the following html code:
It will appear on your page as: Visit Antenna - Theory .com's Antenna Fundamentals Page
Another version:
Thank you for supporting the antenna basics site, where we aim to provide FREE knowledge on antenna basics.
Those textbooks are way too expensive, and not nearly as good at explaining antenna basics in an understandable way!
The work on these Antenna Fundamentals (Antenna Basics) pages is copyrighted. No portion can be reproduced, in print
or online without permission from the author. Copyright antenna-theory.com, 2009-2011.
Frequency
Antenna Definitions Antenna Basics List Main Antenna Page
Frequency is one of the most important concepts in the universe and to antenna theory, which we will
see. But fortunately, it isn't too complicated.
All electromagnetic waves propagate at the same speed in air or in space. This speed (the speed of light)
is roughly 671 million miles per hour (1 billion kilometers per hour). This is roughly a million times
faster than the speed of sound (which is about 761 miles per hour at sea level). The speed of light will
be denoted as c in the equations that follow. We like to use "SI" units in science (length measured in
meters,time in seconds,mass in kilograms), so we will forever remember that:
Before defining frequency, we must define what a "electromagnetic wave" is. This is an electric field
that travels away from some source (an antenna, the sun, a radio tower, whatever). A traveling electric field
has an associated magnetic field with it, and the two make up an electromagnetic wave.
The universe allows these waves to take any shape. The most important shape though is the sinusoidal wave,
which is plotted in Figure 1. EM waves vary with space (position) and time. The spatial variation is given
in Figure 1, and the the temporal (time) variation is given in Figure 2.
The wave is periodic, it repeats itself every T seconds. Plotted as a function in space, it repeats itself every
wavelength meters, which we will call the wavelength. The frequency (written f ) is simply the number
of complete cycles the wave completes (viewed as a function of time) in one second (two hundred cycles
per second is written 200 Hz, or 200 "Hertz"). Mathematically this is written as:
How fast someone walks depends on the size of the steps they take (the wavelength) multipled by the rate at
which they take steps (the frequency). The speed that the waves travel is how fast the waves are
oscillating in time (f ) multiplied by the size of the step the waves are taken per period ( wavelength ).
The equation that relates frequency, wavelength and the speed of light can be tattooed on your forehead:
Basically, the frequency is just a measure of how fast the wave is oscillating. And since all EM waves
travel at the same speed, the faster it oscillates the shorter the wavelength. And a longer wavelength
implies a slower frequency.
This may sound stupid, and actually it probably should. When I was young I remember scientists
discussing frequency and I could never see why it mattered. But it is of fundamental importance, as will
be explained in the "more advanced" section on frequency.
Antenna Fundamentals
Why is frequency so fundamental? To really understand that, we must introduce one of the
coolest mathematical ideas ever (seriously), and that is 'Fourier Analysis'. I had a class on Fourier
Analysis in grad school at Stanford University, and the professor referred to these concepts as 'one of
the fundamental secrets of the universe'.
Let's start with a question. What is the frequency of the following waveform?
Well, you'd look for what the period is and realize that it isn't periodic over the plotted region. Then
you'd tell me the question was stupid. But here we go:
As an example, lets break down the waveform in Figure 1 into its 'building blocks' or the it's
frequencies. This decomposition can be done with a Fourier transform (or Fourier series for periodic
waveforms). The first component is a sinusoidal wave with period T=6.28 (2*pi) and amplitude 0.3,
as shown in Figure 2.
Figure 2. First fundamental frequency (left) and original waveform (right) compared.
The second frequency will have a period half as long as the first (twice the frequency). The
second component is shown on the left in Figure 3, along with the sum of the first two frequencies
compared to the original waveform.
Figure 3. Second fundamental frequency (left) and original waveform compared with the
first two frequency components.
We see that the sum of the first two frequencies is starting to look like the original waveform. The
third frequency component is 3 times the frequency as the first. The sum of the first 3 components
are shown in Figure 4.
Figure 4. Third fundamental frequency (left) and original waveform compared with the first three
frequency components.
Finally, adding in the fourth frequency component, we get the original waveform, shown in Figure 5.
Figure 5. Fourth fundamental frequency (left) and original waveform compared with the
first four frequency components (overlapped).
While this seems made up, it is true for all waveforms. This goes for TV signals, cell phone signals,
the sound waves that travel when you speak. In general, waveforms are not made up of a discrete number
of frequencies, but rather a continuous range of frequencies.
Hence, for all of antenna theory, we will frequency be discussing wavelength of frequency. Actual
antennas radiate real world signals - data from the internet over WIFI, speech signals, etc etc etc. However,
since every piece of information in the universe can be decomposed into sine and cosine components of
varying frequencies, we always discuss antennas in terms of the wavelength it operates at or the
frequency we are using.
As a further consequence of this, the power an antenna can transmit is divided into frequency regions, or
http://www.antenna-theory.com/basics/advfreq.html (6 of 7) [2/28/2013 12:32:38 PM]
Antenna-Theory.com - More Advanced Frequency Concepts for Antennas
frequency bands. In the next section, we'll look at what we can say about these frequency bands.
Frequency Bands
Previous: Frequency Concepts Part
Antenna Fundamentals Main Antenna Page
2
How can your cell phone and your television work at the same time? Both use antennas to
receive information from electromagnetic waves, so why isn't there a problem?
The answer goes back to the fundamental secret of the universe. No matter what information you want
to send, that waveform can be represented as the sum of a range of frequencies. By the use of
modulation (which in a nutshell shifts the frequency range of the waveform to be sent to a higher frequency
band), the waveforms can be relocated to separate frequency bands.
As an example, cell phones that use the PCS (Personal Communications Service) band have their
signals shifted to 1850-1900 MHz. Television is broadcast primarily at 54-216 MHz. FM radio
operates between 87.5-108 MHz.
The set of all frequencies is referred to as "the spectrum". Cell phone companies have to pay big money
to get access to part of the spectrum. For instance, AT&T has to bid on a slice of the spectrum with the
FCC, for the "right" to transmit information within that band. The transmission of EM energy is
greatly regulated. When AT&T is sold a slice of the spectrum, they can not transmit energy at any
other band (technically, the amount transmitted must be below some threshold in adjacent bands).
The Bandwidth of a signal is the difference between the signals high and low frequencies. For instance, a
signal transmitting between 40 and 50 MHz has a bandwidth of 10 MHz. This means that the energy of
the signal is contained between 40 and 50 MHz (and the energy in any other frequency range is negligible).
We'll wrap up with a table of frequency bands along with the corresponding wavelengths. From the
table, we see that VHF is in the range 30-300 MHz (30 Million-300 Million cycles per second). At the
very least then, if someone says they need a "VHF antenna", you should now understand that the
antenna should transmit or receive electromagnetic waves that have a frequency of 30-300 MHz.
Basically the frequency bands each range over from the lowest frequency to 10 times the lowest
frequency. Antenna engineers further divide the bands into things like "X-band" and "Ku-band". That is the
basics of frequency. To understand at a more advanced level, read on, or move to the next topic.
Antenna Basics
Antennas Home
Radiation Pattern
Back: Frequency Bands Antenna Basics Home - Antenna Theory
A radiation pattern defines the variation of the power radiated by an antenna as a function of
the direction away from the antenna. This power variation as a function of the arrival angle
is observed in the antenna's far field.
As an example, consider the 3-dimensional radiation pattern in Figure 1, plotted in decibels (dB) .
Figure 1. Example radiation pattern for an Antenna (generated with FEKO software).
This is an example of a donut shaped or toroidal radiation pattern. In this case, along the z-axis,
http://www.antenna-theory.com/basics/radPattern.html (2 of 5) [2/28/2013 12:32:45 PM]
Radiation Pattern
which would correspond to the radiation directly overhead the antenna, there is very little
power transmitted. In the x-y plane (perpendicular to the z-axis), the radiation is
maximum. These plots are useful for visualizing which directions the antenna radiates.
Typically, because it is simpler, the radiation patterns are plotted in 2-d. In this case, the
patterns are given as "slices" through the 3d plane. The same pattern in Figure 1 is plotted
polar angle theta for plots
in Figure 2. Standard spherical coordinates are used, where in spherical coordinates is the angle
phi, the azimuth angle of
spherical coordinates in
measured off the z-axis, and antenna patterns is the angle measured counterclockwise off
the x-axis.
If you're unfamiliar with radiation patterns or spherical coordinates, it may take a while to see
that Figure 2 represents the same radiation pattern as shown in Figure 1. The radiation pattern
on the left in Figure 2 is the elevation pattern, which represents the plot of the radiation pattern
as a function of the angle measured off the z-axis (for a fixed azimuth angle). Observing Figure
1, we see that the radiation pattern is minimum at 0 and 180 degrees and becomes maximum
broadside to the antenna (90 degrees off the z-axis). This corresponds to the plot on the left in
Figure 2.
The radiation pattern on the right in Figure 2 is the azimuthal plot. It is a function of the
azimuthal angle for a fixed polar angle (90 degrees off the z-axis in this case). Since the
radiation pattern in Figure 1 is symmetrical around the z-axis, this plot appears as a constant in
Figure 2.
A pattern is "isotropic" if the radiation pattern is the same in all directions. Antennas with
isotropic radiation patterns don't exist in practice, but are sometimes discussed as a means of
comparison with real antennas.
Some antennas may also be described as "omnidirectional", which for an actual antenna means
that the radiation pattern is isotropic in a single plane (as in Figure 1 above for the x-y plane, or
the radiation pattern on the right in Figure 2). Examples of omnidirectional antennas include the
dipole antenna and the slot antenna.
The third category of antennas are "directional", which do not have a symmetry in the radiation
pattern. These antennas typically have a single peak direction in the radiation pattern; this is
the direction where the bulk of the radiated power travels. These antennas are very common;
examples of antennas with highly directional radiation patterns include the dish antenna and the
slotted waveguide antenna. An example of a highly directional radiation pattern (from a dish
antenna) is shown in Figure 3:
In summary, the radiation pattern is a plot which allows us to visualize where the antenna
transmits or receives power.
This page on antenna radiation patterns is copyrighted. No portion can be reproduced except by
permission from the author. Copyright antenna-theory.com, 2009-2011, antenna radiation
patterns.
Field Regions
The far field region is the most important, as this determines the antenna's radiation pattern. Also,
antennas are used to communicate wirelessly from long distances, so this is the region of operation for
most antennas. We will start with this region.
The far field is the region far from the antenna, as you might suspect. In this region, the radiation
pattern does not change shape with distance (although the fields still die off as 1/R, the power density
dies off as 1/R^2). Also, this region is dominated by radiated fields, with the E- and H-fields orthogonal
to each other and the direction of propagation as with plane waves.
If the maximum linear dimension of an antenna is D, then the following 3 conditions must all be satisfied
to be in the far field region:
[Equation 1]
[Equation 2]
[Equation 3]
The first and second equation above ensure that the power radiated in a given direction from distinct parts
of the antenna are approximately parallel (see Figure 1). This helps ensure the fields in the far-field
region behave like plane waves. Note that >> means "much much greater than" and is typically
assumed satisfied if the left side is 10 times larger than the right side.
Figure 1. The Rays from any Point on the Antenna are Approximately Parallel in the Far Field.
Finally, where does the third far-field equation come from? Near a radiating antenna, there are
reactive fields (see reactive near field region, below), that typically have the E-fields and H-fields die
off with distance as and . The third equation above ensures that these near fields are gone, and we
are left with the radiating fields, which fall off with distance as .
The far-field region is sometimes referred to as the Fraunhofer region, a carryover term from optics.
In the immediate vicinity of the antenna, we have the reactive near field. In this region, the fields are
predominately reactive fields, which means the E- and H- fields are out of phase by 90 degrees to each
other (recall that for propagating or radiating fields, the fields are orthogonal (perpendicular) but are
in phase).
The radiating near field or Fresnel region is the region between the near and far fields. In this region,
the reactive fields are not dominate; the radiating fields begin to emerge. However, unlike the Far
Field region, here the shape of the radiation pattern may vary appreciably with distance.
Note that depending on the values of R and the wavelength, this field may or may not exist.
Figure 2. Illustration of the Field Regions for an Antenna of Maximum Linear Dimension D.
Next we'll look at numerically describing the directionality of an antenna's radiation pattern.
Antenna Basics
Antennas (Home)
Directivity
Previous: Field Regions Antenna Fundamentals Antennas
[Silly side note: When a directivity is specified for an antenna, what is meant is 'peak
directivity'. Directivity is technically a function of angle, but the angular variation is described by
its radiation pattern. Hence, directivity throughout this page will mean peak directivity, because it
is rarely used in another context.]
A normalized radiation pattern is the same as a radiation pattern; it is just scaled in magnitude such that
the peak (maximum value) of the magnitude of the radiation pattern (F in equation [1]) is equal to
1. Mathematically, the formula for directivity (D) is written as:
This equation for directivity might look complicated, but the numerator is the maximum value of F, and the
denominator just represents the "average power radiated over all directions". This equation then is just
a measure of the peak value of radiated power divided by the average, which gives the directivity of
the antenna.
http://www.antenna-theory.com/basics/directivity.php (1 of 5) [2/28/2013 12:32:51 PM]
Directivity - Antenna-Theory.com
Directivity Example
As an example consider two antennas, one with radiation patterns given by:
directivity 1 Antenna 1
directivity 2 Antenna 2
These radiation patterns are plotted in Figure 1. Note that the patterns are only a function of the polar angle
polar angle theta , and not a function of the azimuth angle (uniform in azimuth). The radiation pattern for
antenna 1 is less directional then that for antenna 2; hence we expect the directivity to be lower.
Figure 1. Plots of Radiation Patterns for Antennas. Which has the higher directivity?.
Using Equation [1], we can figure out which antenna has the higher directivity. But to check
your understanding, you should think about Figure 1 and what directivity is, and determine which has
a higher directivity without using any mathematics.
Again, increased directivity implies a more 'focused' or 'directional' antenna. In words, Antenna 2
receives 2.707 times more power in its peak direction than an isotropic antenna would receive. Antenna
1 would receive 1.273 times the power of an isotropic antenna. The isotropic antenna is used as a
common reference, even though no isotropic antennas exist.
Antennas for cell phones should have a low directivity because the signal can come from any direction,
and the antenna should pick it up. In contrast, satellite dish antennas have a very high directivity,
because they are to receive signals from a fixed direction. As an example, if you get a directTV dish,
they will tell you where to point it such that the antenna will receive the signal.
Finally, we'll conclude with a list of antenna types and their directivities, to give you an idea of what is seen
in practice.
As you can see from the above table, the directivity of an antenna can vary over several order of magnitude.
Hence, it is important to understand directivity in choosing the best antenna for your specific application. If
you need to transmit or receive energy from a wide variety of directions (example: car radio, mobile phones,
computer wifi), then you should design an antenna with a low directivity. Conversely, if you are
doing remote sensing, or targetted power transfer (example: received signal from a mountain top), you
want a high directivity antenna, to maximize power transfer and reduce signal from unwanted directions.
Let's say we decide that we want an antenna with a low directivity. How do we accomplish this?
The general rule in Antenna Theory is that you need an electrically small antenna to produce low directivity.
That is, if you use an antenna with a total size of 0.25 - 0.5 wavelength for directivity (a quarter- to a half-
http://www.antenna-theory.com/basics/directivity.php (3 of 5) [2/28/2013 12:32:51 PM]
Directivity - Antenna-Theory.com
wavelength in size), then you will minimize directivity. That is, half-wave dipole antennas or
half-wavelength slot antennas typically have directivities less than 3 dB, which is about as low of
a directivity as you can obtain in practice. Ultimately, we can't make antennas much smaller than a quarter-
wavelength without sacrificing antenna efficiency (the next topic) and antenna bandwidth.
Conversely, for antennas with a high directivity, we'll need antennas that are many wavelengths in size.
That is, antennas such as dish (or satellite) antennas and horn antennas have high directivity, in part because
they are many wavelengths long.
Why is this? [I don't know how to explain this without getting mathematical, sorry!] Ultimately, it
has to do with the properties of the Fourier Transform. When you take the Fourier Transform of a
short pulse, you get a broad frequency spectrum. The analogy is present in determining the
radiation pattern of an antenna: the pattern can be thought of as the Fourier Transform of
the antenna's current or voltage distribution. As a result, small antennas have broad
radiation patterns (low directivity), and antennas with large uniform voltage or current distributions
have very directional patterns (and thus, a high directivity).
Now that we know what directivity is, we can move on to the next antenna concept, gain.
(Home) Antennas
This directivity page is copyrighted. No portion can be reproduced without permission from the author.
Copyright antenna-theory.com, 2009-2011.
On this page, we'll introduce two fundamental antenna parameters: antenna efficiency and antenna gain.
Antenna Efficiency
The efficiency of an antenna relates the power delivered to the antenna and the power radiated or
dissipated within the antenna. A high efficiency antenna has most of the power present at the antenna's
input radiated away. A low efficiency antenna has most of the power absorbed as losses within the
antenna, or reflected away due to impedance mismatch.
[Side Note: Antenna Impedance is discussed in a later section. Impedance Mismatch is simply power
reflected from an antenna because it's impedance is not the correct value; hence, "impedance mismatch". ]
The losses associated within an antenna are typically the conduction losses (due to finite conductivity of
the antenna) and dielectric losses (due to conduction within a dielectric which may be present within
an antenna).
The antenna efficiency (or radiation efficiency) can be written as the ratio of the radiated power to the
input power of the antenna:
[Equation 1]
Efficiency is ultimately a ratio, giving a number between 0 and 1. Efficiency is very often quoted in terms of
a percentage; for example, an efficiency of 0.5 is the same as 50%. Antenna efficiency is also frequently
quoted in decibels (dB); an efficiency of 0.1 is 10% or (-10 dB), and an efficiency of 0.5 or 50% is -3 dB.
Equation [1] is sometimes referred to as the antenna's radiation efficiency. This distinguishes it from
another sometimes-used term, called an antenna's "total efficiency". The total efficiency of an antenna is the
radiation efficiency multiplied by the impedance mismatch loss of the antenna, when connected to
a transmission line or receiver (radio or transmitter). This can be summarized in Equation [2], where is
the antenna's total efficiency, is the antenna's loss due to impedance mismatch, and is
the antenna's radiation efficiency.
[Equation 2]
Since is always a number between 0 and 1, the total antenna efficiency is always less than
the antenna's radiation efficiency. Said another way, the radiation efficiency is the same as the total
antenna efficiency if there was no loss due to impedance mismatch.
Efficiency is one of the most important antenna parameters. It can be very close to 100% (or 0 dB) for dish,
horn antennas, or half-wavelength dipoles with no lossy materials around them. Mobile phone antennas,
or wifi antennas in consumer electronics products, typically have efficiencies from 20%-70% (-7 to -
1.5 dB). The losses are often due to the electronics and materials that surround the antennas; these tend to
absorb some of the radiated power (converting the energy to heat), which lowers the efficiency of
the antenna. Car radio antennas can have a total antenna efficiency of -20 dB (1% efficiency) at the
AM radio frequencies; this is because the antennas are much smaller than a half-wavelength at
the operational frequency, which greatly lowers antenna efficiency. The radio link is maintained because the
AM Broadcast tower uses a very high transmit power.
Improving impedance mismatch loss is discussed in the Smith Charts and impedance matching
section. Impedance matching can greatly improve the efficiency of an antenna.
Antenna Gain
The term Antenna Gain describes how much power is transmitted in the direction of peak radiation to
that of an isotropic source. Antenna gain is more commonly quoted in a real antenna's specification
sheet because it takes into account the actual losses that occur.
An antenna with a gain of 3 dB means that the power received far from the antenna will be 3 dB
higher (twice as much) than what would be received from a lossless isotropic antenna with the same input
power.
Antenna Gain is sometimes discussed as a function of angle, but when a single number is quoted the gain
is the 'peak gain' over all directions. Antenna Gain (G) can be related to directivity (D) by:
[Equation 3]
The gain of a real antenna can be as high as 40-50 dB for very large dish antennas (although this is
rare). Directivity can be as low as 1.76 dB for a real antenna (example: short dipole antenna), but can
never theoretically be less than 0 dB. However, the peak gain of an antenna can be arbitrarily low because
of losses or low efficiency. Electrically small antennas (small relative to the wavelength of the
frequency that the antenna operates at) can be very inefficient, with antenna gains lower than -10 dB
(even without accounting for impedance mismatch loss).
Antenna Basics
This page on antenna efficiency and antenna gain is copyrighted. No portion can be reproduced
without permission from the author. Copyright antenna-theory.com, 2009-2011.
In addition to directivity, the radiation patterns of antennas are also characterized by their beamwidths
and sidelobe levels (if applicable).
These concepts can be easily illustrated. Consider the radiation pattern given by:
This pattern is actually fairly easy to generate using Antenna Arrays, as will be seen in that section. The
3-dimensional view of this radiation pattern is given in Figure 1.
The polar (polar angle measured off of z-axis) plot is given by:
The main beam is the region around the direction of maximum radiation (usually the region that is within
3 dB of the peak of the main beam). The main beam in Figure 2 is centered at 90 degrees.
The sidelobes are smaller beams that are away from the main beam. These sidelobes are usually radiation
in undesired directions which can never be completely eliminated. The sidelobes in Figure 2 occur
at roughly 45 and 135 degrees.
The Half Power Beamwidth (HPBW) is the angular separation in which the magnitude of the
radiation pattern decrease by 50% (or -3 dB) from the peak of the main beam. From Figure 2, the
pattern decreases to -3 dB at 77.7 and 102.3 degrees. Hence the HPBW is 102.3-77.7 = 24.6 degrees.
Another commonly quoted beamwidth is the Null to Null Beamwidth. This is the angular separation
from which the magnitude of the radiation pattern decreases to zero (negative infinity dB) away from the
main beam. From Figure 2, the pattern goes to zero (or minus infinity) at 60 degrees and 120
degrees. Hence, the Null-Null Beamwidth is 120-60=60 degrees.
Finally, the Sidelobe Level is another important parameter used to characterize radiation patterns.
The sidelobe level is the maximum value of the sidelobes (away from the main beam). From Figure 2,
the Sidelobe Level (SLL) is -14.5 dB.
Antenna Basics
This page on sidelobes, beamwidths, HPBW and other radiation pattern definitions is copyrighted.
No portion can be reproduced without permission from the author. Copyright antenna-theory.com,
2009-2011.
Antenna Impedance
Antenna impedance relates the voltage to the current at the input to the antenna. This is extremely important
as we will see.
Let's say an antenna has an impedance of 50 ohms. This means that if a sinusoidal voltage is applied at
the antenna terminals with an amplitude of 1 Volt, then the current will have an amplitude of 1/50 = 0.02
Amps. Since the impedance is a real number, the voltage is in-phase with the current.
Alternatively, suppose the impedance is given by a complex number, say Z=50 + j*50 ohms.
Note that "j" is the square root of -1. Imaginary numbers are there to give phase information. If
the impedance is entirely real [Z=50 + j*0], then the voltage and current are exactly in time-phase. If
the impedance is entirely imaginary [Z=0 + j*50], then the voltage leads the current by 90 degrees in phase.
This means the phase of the current will lag the voltage by 45 degrees. That is, the current waveform
is delayed relative to the voltage waveform. To spell it out, if the voltage (with frequency f) at the antenna
terminals is given by
Hence, antenna impedance is a simple concept. Impedance relates the voltage and current at the input to the
antenna. The real part of the antenna impedance represents power that is either radiated away or absorbed
within the antenna. The imaginary part of the impedance represents power that is stored in the near field of
the antenna. This is non-radiated power. An antenna with a real input impedance (zero imaginary part)
is said to be resonant. Note that the impedance of an antenna will vary with frequency.
While simple, we will now explain why this is important, considering both the low frequency and
high frequency cases.
Low Frequency
When we are dealing with low frequencies, the transmission line that connects the transmitter or receiver
to the antenna is short. Short in antenna theory always means "relative to a wavelength". Hence, 5
meters could be short or very long, depending on what frequency we are operating at. At 60 Hz,
the wavelength is about 3100 miles, so the transmission line can almost always be neglected. However, at
2 GHz, the wavelength is 15 cm, so the little length of line within your cell phone can often be considered a
'long line'. Basically, if the line length is less than a tenth of a wavelength, it is reasonably considered a
short line.
Consider an antenna (which is represented as an impedance given by ZA) hooked up to a voltage source
(of magnitude V) with source impedance given by ZS. The equivalent circuit of this is shown in Figure 1.
From circuit theory, we know that P=I*V. The power that is delivered to the antenna is:
If ZA is much smaller in magnitude than ZS, then no power will be delivered to the antenna and it
won't transmit or receive energy. If ZA is much larger in magnitude than ZS, then no power will
be delivered as well.
For maximum power to be transferred from the generator to the antenna, the ideal value for the
antenna impedance is given by:
The * in the above equation represents complex conjugate. So if ZS=30+j*30 ohms, then for
maximum power transfer the antenna should impedance ZA=30-j*30 ohms. Typically, the
source impedance is real (imaginary part equals zero), in which case maximum power transfer occurs
when ZA=ZS.
Hence, we now know that for an antenna to work properly, its impedance must not be too large or too
small. It turns out that this is one of the fundamental design parameters for an antenna, and it isn't
always easy to design an antenna with the right impedance - particularly over a wide frequency range.
High Frequency
This section will be a little more advanced. In low-frequency circuit theory, the wires that connect
things don't matter. Once the wires become a significant fraction of a wavelength, they make things
very different. For instance, a short circuit has an impedance of zero ohms. However, if the impedance
is measured at the end of a quarter wavelength transmission line, the impedance appears to be infinite,
even though there is a dc conduction path.
In general, the transmission line will transform the impedance of an antenna, making it very difficult
to deliver power, unless the antenna is matched to the transmission line. Consider the situation shown
in Figure 2. The impedance is to be measured at the end of a transmission line (with
characteristic impedance Z0) and Length L. The end of the transmission line is hooked to an antenna
with impedance ZA.
It turns out (after studying transmission line theory for a while), that the input impedance Zin is given by:
This is a little formidable for an equation to understand at a glance. However, the happy thing is:
If the antenna is matched to the transmission line (ZA=ZO), then the input impedance does
not depend on the length of the transmission line.
This makes things much simpler. If the antenna is not matched, the input impedance will vary widely
with the length of the transmission line. And if the input impedance isn't well matched to the
source impedance, not very much power will be delivered to the antenna. This power ends up
being reflected back to the generator, which can be a problem in itself (especially if high power
is transmitted). This loss of power is known as impedance mismatch. Hence, we see that having a
tuned impedance for an antenna is extremely important. For more information on transmission lines, see
the transmission line tutorial.
VSWR
poorly matched antenna will not radiate power. This can be somewhat alleviated via impedance matching,
although this doesn't always work over a sufficient bandwidth (bandwidth is the next topic).
A common measure of how well matched the antenna is to the transmission line or receiver is known as
the Voltage Standing Wave Ratio (VSWR). VSWR is a real number that is always greater than or equal to 1.
A VSWR of 1 indicates no mismatch loss (the antenna is perfectly matched to the tx line). Higher values
of VSWR indicate more mismatch loss.
As an example of common VSWR values, a VSWR of 3.0 indicates about 75% of the power is delivered
to the antenna (1.25 dB of mismatch loss); a VSWR of 7.0 indicates 44% of the power is delivered to
the antenna (3.6 dB of mismatch loss). A VSWR of 6 or more is pretty high and will generally need to
be improved.
The parameter VSWR sounds like an overly complicated concept; however, power reflected by an
antenna on a transmission line interferes with the forward travelling power - and this creates a
standing voltage wave - which can be numerically evaluated by the quantity Voltage Standing Wave
Ratio (VSWR). For more information, see the page on VSWR and VSWR Specifications.
In the next section on antenna basics, we'll look at the very important antenna parameter known
as bandwidth.
Antenna Basics
This page on antenna impedance is copyrighted. No portion can be reproduced or copied without
permission from the author. Copyright antenna-theory.com, 2008-2011.
Bandwidth
Bandwidth is another fundamental antenna parameter. Bandwidth describes the range of frequencies
over which the antenna can properly radiate or receive energy. Often, the desired bandwidth is one of
the determining parameters used to decide upon an antenna. For instance, many antenna types have
very narrow bandwidths and cannot be used for wideband operation.
Bandwidth is typically quoted in terms of VSWR. For instance, an antenna may be described as operating
at 100-400 MHz with a VSWR<1.5. This statement implies that the reflection coefficient is less than
0.2 across the quoted frequency range. Hence, of the power delivered to the antenna, only 4% of the
power is reflected back to the transmitter. Alternatively, the return loss S11=20*log10(0.2)=-13.98 dB.
Note that the above does not imply that 96% of the power delivered to the antenna is transmitted in the
form of EM radiation; losses must still be taken into account.
Also, the radiation pattern will vary with frequency. In general, the shape of the radiation pattern does
not change radically.
There are also other criteria which may be used to characterize bandwidth. This may be the polarization over
a certain range, for instance, an antenna may be described as having circular polarization with an axial
ratio < 3dB (less than 3 dB) from 1.4-1.6 GHz. This polarization bandwidth sets the range over which
the antenna's operation is approximately circularly polarized.
The bandwidth is often specified in terms of its Fractional Bandwidth (FBW). The FBW is the ratio of the
frequecny range (highest frequency minus lowest frequency) divided by the center frequency. The
antenna Q also relates to bandwidth (higher Q is lower bandwidth, and vice versa).
To give some concrete examples of bandwidth, here is a table of the bandwidths for common antenna
types. This will answer such questions as "what is the bandwidth of a dipole antenna?" and "which
antenna has a higher bandwidth - a patch or a spiral antenna?". For a fare comparison, we set the
center frequency for each antenna to 1 GHz (1000 MHz).
As can be seen from Table I, the bandwidth for antennas can vary widely. Patch (Microstrip) Antennas
are very low bandwidth, while spiral antennas have a very large bandwdith.
Antenna Basics
Antennas (Home)
This page on bandwidth is copyrighted. No portion can be reproduced or copied without permission
from the author. Copyright antenna-theory.com, 2008-2011.
Linear Polarization
In equation (1), the symbol unit vector is a unit vector (a vector with a length of one), which says that the
E-field "points" in the x-direction.
Polarization is the figure that the E-field traces out while propagating. As an example, consider the E-
field observed at (x,y,z)=(0,0,0) as a function of time for the plane wave described by equation (1)
above. The amplitude of this field is plotted in Figure 2 at several instances of time. The field is
oscillating at frequency f.
Observed at the origin, the E-field oscillates back and forth in magnitude, always directed along the x-
axis. Because the E-field stays along a single line, this field would be said to be linearly polarized.
In addition, if the x-axis was parallel to the ground, this field could also be described as
"horizontally polarized" (or sometimes h-pole in the industry). If the field was oriented along the y-axis, this
wave would be said to be "vertically polarized" (or v-pole).
A linearly polarized wave does not need to be along the horizontal or vertical axis. For instance, a wave with
an E-field constrained to lie along the line shown in Figure 3 would also be linearly polarized.
The E-field in Figure 3 could be described by equation (2). The E-field now has an x- and y-
component, equal in magnitude.
One thing to notice about equation (2) is that the x- and y-components of the E-field are in phase - they
both have the same magnitude and vary at the same rate.
Circular Polarization
Suppose now that the E-field of a plane wave was given by equation (3):
mathematical description of
E-field in a circularly
polarized field
In this case, the x- and y- components are 90 degrees out of phase. If the field is observed at (x,y,z)=
(0,0,0) again as before, the plot of the E-field versus time would appear as shown in Figure 4.
The E-field in Figure 4 rotates in a circle. This type of field is described as a circularly polarized wave.
To have circular polarization, the following criteria must be met:
If the wave in Figure 4 is travelling out of the screen, the field is rotating in the counter-clockwise
direction and is said to be Right Hand Circularly Polarized (RHCP). If the fields were rotating in
the clockwise direction, the field would be Left Hand Circularly Polarized (LHCP).
Elliptical Polarization
If the E-field has two perpendicular components that are out of phase by 90 degrees but are not equal
in magnitude, the field will end up Elliptically Polarized. Consider the plane wave travelling in the
+z-direction, with E-field described by equation (4):
description of elliptical
polarizations in equation
form
The locus of points that the tip of the E-field vector would assume is given in Figure 5.
The field in Figure 5, travels in the counter-clockwise direction, and if travelling out of the screen would
be Right Hand Elliptically Polarized. If the E-field vector was rotating in the opposite direction, the field
would be Left Hand Elliptically Polarized.
In addition, elliptical polarization is defined by its eccentricity, which is the ratio of the major and
minor axis amplitudes. For instance, the eccentricity of the wave given by equation (4) is 1/0.3 =
3.33. Elliptically polarized waves are further described by the direction of the major axis. The wave
of equation (4) has a major axis given by the x-axis. Note that the major axis can be at any angle in
the plane, it does not need to coincide with the x-, y-, or z-axis. Finally, note that circular polarization
and linear polarization are both special cases of elliptical polarization. An elliptically polarized wave with an
eccentricity of 1.0 is a circularly polarized wave; an elliptically polarized wave with an infinite
eccentricity is a linearly polarized wave.
In the next section, we will use the knowledge of plane-wave polarization to characterize and
understand antennas.
Polarization of Antennas
Now that we are aware of the polarization of plane-wave EM fields, antenna polarization
is straightforward to define.
The polarization of an antenna is the polarization of the radiated fields produced by an antenna, evaluated in
the far field. Hence, antennas are often classified as "Linearly Polarized" or a "Right Hand
Circularly Polarized Antenna".
This simple concept is important for antenna to antenna communication. First, a horizontally
polarized antenna will not communicate with a vertically polarized antenna. Due to the reciprocity
theorem, antennas transmit and receive in exactly the same manner. Hence, a vertically polarized
antenna transmits and receives vertically polarized fields. Consequently, if a horizontally polarized
antenna is trying to communicate with a vertically polarized antenna, there will be no reception.
In general, for two linearly polarized antennas that are rotated from each other by an angle , the
power loss due to this polarization mismatch will be described by the Polarization Loss Factor (PLF):
Hence, if both antennas have the same polarization, the angle between their radiated E-fields is zero
and there is no power loss due to polarization mismatch. If one antenna is vertically polarized and the
other is horizontally polarized, the angle is 90 degrees and no power will be transferred.
As a side note, this explains why moving the cell phone on your head to a different angle can
sometimes increase reception. Cell phone antennas are often linearly polarized, so rotating the phone can
often match the polarization of the phone and thus increase reception.
Circular polarization is a desirable characteristic for many antennas. Two antennas that are both
circularly polarized do not suffer signal loss due to polarization mismatch. Antennas used in GPS
systems are Right Hand Circularly Polarized.
Suppose now that a linearly polarized antenna is trying to receive a circularly polarized wave. Equivalently,
suppose a circularly polarized antenna is trying to receive a linearly polarized wave. What is the resulting
Polarization Loss Factor?
Recall that circular polarization is really two orthongal linear polarized waves 90 degrees out of
phase. Hence, a linearly polarized (LP) antenna will simply pick up the in-phase component of the
circularly polarized (CP) wave. As a result, the LP antenna will have a polarization mismatch loss of 0.5 (-
3dB), no matter what the angle the LP antenna is rotated to. Therefore:
The Polarization Loss Factor is sometimes referred to as polarization efficiency, antenna mismatch factor,
or antenna receiving factor. All of these names refer to the same concept.
Antenna Fundamentals
Antennas (Homepage)
This page on polarization and antennas is copyrighted. No portion can be reproduced without
permission from the author. Copyright antenna-theory.com, 2009-2011. Polarization, antenna
polarization, polarization of antennas.
A useful parameter calculating the receive power of an antenna is the effective area or effective
aperture. Assume that a plane wave with the same polarization as the receive antenna is incident upon
the antenna. Further assume that the wave is travelling towards the antenna in the antenna's direction of
maximum radiation (the direction from which the most power would be received).
Then the effective aperture parameter describes how much power is captured from a given plane wave. Let p
be the power density of the plane wave (in W/m^2). If P_t represents the power (in Watts) at the antennas
terminals available to the antenna's receiver, then:
Hence, the effective area simply represents how much power is captured from the plane wave and
delivered by the antenna. This area factors in the losses intrinsic to the antenna (ohmic losses,
dielectric losses, etc.).
A general relation for the effective aperture in terms of the peak antenna gain (G) of any antenna is given by:
effective aperture as a
function of peak gain and
wavelength
Effective aperture or effective area can be measured on actual antennas by comparison with a
known antenna with a given effective aperture, or by calculation using the measured gain and the
above equation.
Effective aperture will be a useful concept for calculating received power from a plane wave. To see this
in action, go to the next section on the Friis transmission formula.
Antenna Fundamentals
Antenna Theory
This page on antenna aperture is copyrighted. No portion can be reproduced without permission from
the author. Copyright antenna-theory.com, 2009-2011. Effective aperture, antenna aperture.
On this page, we introduce one of the most fundamental equations in antenna theory, the
Friis Transmission Equation. The Friis Transmission Equation is used to calculate the power
received from one antenna (with gain G1), when transmitted from another antenna (with gain G2),
separated by a distance R, and operating at frequency f or wavelength lambda. This page is worth reading
a couple times and should be fully understood.
To begin the derivation of the Friis Equation, consider two antennas in free space (no obstructions
nearby) separated by a distance R:
Assume that friis transmission formula Watts of total power are delivered to the transmit antenna. For
the moment, assume that the transmit antenna is omnidirectional, lossless, and that the receive antenna is
in the far field of the transmit antenna. Then the power density p (in Watts per square meter) of the
plane wave incident on the receive antenna a distance R from the transmit antenna is given by:
If the transmit antenna has an antenna gain in the direction of the receive antenna given by , then
the power density equation above becomes:
antennas
The gain term factors in the directionality and losses of a real antenna. Assume now that the receive
antenna has an effective aperture given by antenna theory . Then the power received by this antenna
( antenna tutorial ) is given by:
Friis
Since the effective aperture for any antenna can also be expressed as:
effective aperture
This is known as the Friis Transmission Formula. It relates the free space path loss, antenna gains
and wavelength to the received and transmit powers. This is one of the fundamental equations in
antenna theory, and should be remembered (as well as the derivation above).
Another useful form of the Friis Transmission Equation is given in Equation [2]. Since wavelength
and frequency f are related by the speed of light c (see intro to frequency page), we have the
Friis Transmission Formula in terms of frequency:
[Equation 2]
Equation [2] shows that more power is lost at higher frequencies. This is a fundamental result of the
Friis Transmission Equation. This means that for antennas with specified gains, the energy transfer will
be highest at lower frequencies. The difference between the power received and the power transmitted
is known as path loss. Said in a different way, Friis Transmission Equation says that the path loss is
higher for higher frequencies.
The importance of this result from the Friis Transmission Formula cannot be overstated. This is why
mobile phones generally operate at less than 2 GHz. There may be more frequency spectrum available
at higher frequencies, but the associated path loss will not enable quality reception. As a
further consequence of Friss Transmission Equation, suppose you are asked about 60 GHz antennas.
Noting that this frequency is very high, you might state that the path loss will be too high for long
range communication - and you are absolutely correct. At very high frequencies (60 GHz is
sometimes referred to as the mm (millimeter wave) region), the path loss is very high, so only point-to-
point communication is possible. This occurs when the receiver and transmitter are in the same room,
and facing each other.
As a further corrollary of Friis Transmission Formula, do you think the mobile phone operators are
happy about the new LTE (4G) band, that operates at 700MHz? The answer is yes: this is a lower
frequency than antennas traditionally operate at, but from Equation [2], we note that the path loss
will therefore be lower as well. Hence, they can "cover more ground" with this frequency spectrum, and
a Verizon Wireless executive recently called this "high quality spectrum", precisely for this reason.
Side Note: On the other hand, the cell phone makers will have to fit an antenna with a larger wavelength
in a compact device (lower frequency = larger wavelength), so the antenna designer's job got a little
more complicated!
Finally, if the antennas are not polarization matched, the above received power could be multiplied by
the Polarization Loss Factor (PLF) to properly account for this mismatch. Equation [2] above can be
altered to produce a generalized Friis Transmission Formula, which includes polarization mismatch:
[Equation 3]
See also decibel math, which can greatly simplify the calculation of the Friis Transmission Equation.
Antenna Basics
This page on the Friis Transmission Equation (or Friis Transmission Formula) is copyrighted. No
portion can be reproduced without permission from the author. Copyright antenna-theory.com, 2009-2011.
Antenna Temperature
Previous:Friis Transmission
Antenna Basics Antennas (Home)
Equation
Antenna Temperature ( ) is a parameter that describes how much noise an antenna produces in a
given environment. This temperature is not the physical temperature of the antenna. Moreover, an antenna
does not have an intrinsic "antenna temperature" associated with it; rather the temperature depends on
its gain pattern and the thermal environment that it is placed in. Antenna temperature is also sometimes
referred to as Antenna Noise Temperature.
To define the environment, we'll introduce a temperature distribution - this is the temperature in
every direction away from the antenna in spherical coordinates. For instance, the night sky is roughly 4
Kelvin; the value of the temperature pattern in the direction of the Earth's ground is the physical
temperature of the Earth's ground. This temperature distribution will be written as . Hence,
an antenna's temperature will vary depending on whether it is directional and pointed into space or staring
into the sun.
For an antenna with a radiation pattern given by , the noise temperature is mathematically
defined as:
This states that the temperature surrounding the antenna is integrated over the entire sphere, and weighted
by the antenna's radiation pattern. Hence, an isotropic antenna would have a noise temperature that is
the average of all temperatures around the antenna; for a perfectly directional antenna (with a pencil
beam), the antenna temperature will only depend on the temperature in which the antenna is "looking".
The noise power received from an antenna at temperature can be expressed in terms of the
bandwidth (B) the antenna (and its receiver) are operating over:
In the above, K is Boltzmann's constant (1.38 * 10^-23 [Joules/Kelvin = J/K]). The receiver also has
a temperature associated with it ( ), and the total system temperature (antenna plus receiver) has a
combined temperature given by . This temperature can be used in the above equation to find
the total noise power of the system. These concepts begin to illustrate how antenna engineers
must understand receivers and the associated electronics, because the resulting systems very much
depend on each other.
A parameter often encountered in specification sheets for antennas that operate in certain environments
is the ratio of gain of the antenna divided by the antenna temperature (or system temperature if a receiver
is specified). This parameter is written as G/T, and has units of dB/Kelvin [dB/K].
Antenna Fundamentals
This page on antenna temperature is copyrighted. No portion can be reproduced without permission from the
author. Copyright antenna-theory.com, 2009-2011.
Obtaining an intuitive idea for why antennas radiate is helpful in understanding the fundamentals
of antennas. On this page, I'll attempt to give a low-key explanation with no regard to mathematics on
how and why antennas radiate electromagnetic fields.
First, let's start with some basic physics. There is electric charge - this is a quantity of nature (like mass
or weight or density) that every object possesses. You and I are most likely electrically neutral - we
don't have a net charge that is positive or negative. There exists in every atom in the universe particles that
contain positive and negative charge (protons and electrons, respectively). Some materials (like metals)
that are very electrically conductive have loosely bound electrons. Hence, when a voltage is applied across a
metal, the electrons travel around a circuit - this flow of electrons is electric current (measured in Amps).
Let us get back to charge for a moment. Suppose that for some reason, there is a negatively charged
particle sitting somewhere in space. The universe has decided, for unknown reasons, that all
charged particles will have an associated electric field with them. This is illustrated in Figure 1.
Figure 1. A negative charge has an associated Electric Field with it, everywhere in space.
So this negatively charged particle produces an electric field around it, everywhere in space. The
Electric Field is a vector quantity - it has a magnitude (how strong the field strength is) and a
direction (which direction does the field point). The field strength dies off (becomes smaller in
magnitude) as you move away from the charge. Further, the magnitude of the E-field depends on how
much charge exists. If the charge is positive, the E-field lines point away from the charge.
Now, suppose someone came up and punched the charge with their fist, for the fun of it. The charge
would accelerate and travel away at a constant velocity. How would the universe react in this situation?
The universe has also decided (again, for no apparent reason) that disturbances due to moving
(or accelerating) charges will propagate away from the charge at the speed of light - c0 =
300,000,000 meters/second. This means the electric fields around the charge will be disturbed, and this
Once the charge is accelerated, the fields need to re-align themselves. Remember, the fields want
to surround the charge exactly as they did in Figure 1. However, the fields can only respond to events at
the speed of light. Hence, if a point is very far away from the charge, it will take time for the disturbance
(or change in electric fields) to propagate to the point. This is illustrated in Figure 2.
In Figure 2, we have 3 regions. In the light blue (inner) region, the fields close to the charge have
readapted themselves and now line up as they do in Figure 1. In the white region (outermost), the fields
are still undisturbed and have the same magnitude and direction as they would if the charge had not
moved. In the pink region, the fields are changing - from their old magnitude and direction to their
new magnitude and direction.
Hence, we have arrived at the fundamental reason for radiation - the fields change because charges
are accelerated. The fields always try to align themselves as in Figure 1 around charges. If we can produce a
moving set of charges (this is simply electric current), then we will have radiation.
Now, you may have some questions. First - if all accelerating electric charges radiate, then the wires
that connect my computer to the wall should be antennas, correct? The charges on them are oscillating at
60 Hertz as the current travels so this should yield radiation, correct?
Answer: Yes. Your wires do act as antennas. However, they are very poor antennas. The reason
(among other things), is that the wires that carry power to your computer are a transmission line - they
carry current to your computer (which travels to one of your battery's terminals and out the other terminal)
and then they carry the current away from your computer (all current travels in a circuit or loop). Hence, the
radiation from one wire is cancelled by the current flowing in the adjacent wire (that is travelling
the opposite direction).
Another question that will arise is - if its so simple, then everything could be an antenna. Why don't I
just use a metal paper clip as an antenna, hook it up to my receiver and then forget all about antenna theory?
Answer: A paper clip could definitely act as an antenna if you get current flowing on the antenna.
However, it is not so simple to do this. The impedance of the paper clip will control how much power your
receiver or transmitter could deliver to the paper clip (i.e. whether or not you could get any current
flowing on the paper clip at all). The impedance will depend on what frequency you are operating at.
Hence, the paper clip will work at certain frequencies as an antenna. However, you will have to know
much more about antennas before you can say when and it may work in a given situation.
In summary, all radiation is caused by accelerating charges which produce changing electric fields. And due
to Maxwell's Equations, changing electric fields give rise to changing magnetic fields, and hence we
have electromagnetic radiation. The subject of antenna theory is concerned with transferring power
from your receiver (the energy is contained in voltages and currents) into electromagnetic radiation
(where the energy is contained in the E- and H-fields) travelling away from the antenna. This requires
the impedance of your antenna to be roughly matched to your receiver, and that the currents that cause
radiation add up in-phase (that is, they don't cancel each other out as they would in a transmission line).
A multitude of antenna types produce ways of achieving this, and you can find descriptions about them
on the antenna list page.
This page on why antennas radiate or "how does an antenna radiate" is copyrighted. No portion can
be reproduced without permission from the author. Copyright antenna-theory.com, 2009-2011.
Antenna Types
Antenna Tutorial (Home)
In this section, we'll introduce the fundamental antenna types. Almost every antenna in the world can be understood as some
combination or derivative of the antennas listed on this page. We'll start with the simplest of all antennas, the short-
dipole antenna (which is basically a short wire), and work our way through to the more complicated antennas.
Antennas (Home)
This page on the antenna types (list of antennas) is copyrighted. No portion can be reproduced without
permission form the author. Copyright antenna-theory.com, 2011, antenna list, antenna types.
Welcome to Antenna-Theory.com!
Introduction to Antennas
Antenna Basics
Types of Antennas
Antenna Arrays
Antenna Measurements
Antenna Definitions
Antenna Forum
Email Address:
The work on this website is copyrighted. No portion of this antenna website may be copied
without permission from the author. Copyright 2009-2011 Antenna-Theory.com. Antennas,
Antenna Basics, Antenna Gain.
Antennas and Antenna Theory has always been a fascinating subject for me, and it is this
excitement that leads me to present this tutorial. In my life, I have found that once I thoroughly
understand a subject, I am amazed at how simple it seems, despite the initial complexity. This I
have found true for a wide range of activities, be it riding a motorcycle, learning about
antennas, or understanding physical phenomena such as electromagnetics. With that in mind, I
endeavor to write this Antenna Theory website in the simplest of all possible manners.
Specifically, consider this statement: Complexity is not a sign of intelligence; simplify. I have
found this to a priceless amount of wisdom. In that regard, one need not know the intricacies of
Lebesgue integration or complex integrals involving Cauchy residues in order to fully understand
Antenna Theory. In fact, most people who focus on the mathematical intricacies of Maxwell's
Equations tend to be poor practicing antenna engineers (probably because they try to write
code or derive integrals instead of put a product together). The subject of Antennas is best
understood intuitively; this is in stark contrast to the methods in University, where complex
math pervades every page. I do not think this approach effectively teaches antenna theory. In
these pages you will not find rigorous mathematical analysis which only apply in the simplest of
antenna cases (and are ultimately artificial for the real world); I will try to state facts and a
minimum of math except where necessary. I also try to avoid making things unnecessarily
http://www.antenna-theory.com/ (2 of 3) [2/28/2013 12:33:22 PM]
The Antenna Theory Website
complicated. For instance, VSWR stands for Voltage Standing Wave Ratio, and sounds very
complicated. But it is simply a measure of how much power is reflected from an antenna.
Avoiding unnecessary complexity is a lifelong goal of mine.
About me:
I am a practicing antenna engineer, with a PhD in antennas and I have worked for many years
in defense, university and the consumer electronics field as an antenna engineer. My
dissertation in pdf form is available here: Antenna Arrays: Performance Limits and Geometry
Optimization.
Other Projects:
A daylight saving time project entitled when does the time change, and a "Where are the?"
website, for discussion based location, as in Where are the Maldives?.