Professional Documents
Culture Documents
Civil Engineering Assistant - CTS2.0 - NSQF-4
Civil Engineering Assistant - CTS2.0 - NSQF-4
NSQF LEVEL- 4
SECTOR – CONSTRUCTION
CIVIL ENGINEERING
ASSISTANT
(Engineering Trade)
Version: 2.0
NSQF LEVEL - 4
Developed By
1
CONTENTS
1. Course Information 1
2. Training System 3
3. Job Role 7
4. General Information 8
5. Learning Outcome 10
6. Assessment Criteria 13
7. Trade Syllabus 30
1
Civil Engineering Assistant
1. COURSE INFORMATION
During the two-years duration, a candidate is trained on subjects viz. Professional Skill,
Professional Knowledge and Employability Skills related to job role. In addition to this a candidate is
entrusted to make/do project work and Extra Curricular Activities to build up confidence. The
practical skills are imparted in simple to complex manner & simultaneously theory subject is taught
in the same fashion to apply cognitive knowledge while executing task. The practical part starts
with simple geometrical drawing and finally ends with preparing sanction plan of Residential /
Public building including Architecture & Structural drawing, preparation of map Site Plan, use of
different survey instrument, Preparation of Sanitary & Plumbing Layout, detail estimation and
costing, bill of materials, BBS of different RCC structures, different maintenance of civil works,
Project management of site at the end of the course. The broad components covered under
Professional Skill subject are as below:
FIRST YEAR: The practical part starts with basic drawing (consisting of geometrical figure, symbols
& representations). Later the drawing skills imparted are drawing of different scales, projections,
drawing of convertions of three views from pictorial views, section drawing of single storied
building main wall. Practical training imparted to Identify different building materials, Marking
excavation lines & fixing of plinth & floor levels. Setting out foundation trench, Performing brick
masonry, plastering, damp proofing, flooring, arches / lintel, stair etc. Practical traing imparted to
Perform site survey and prepare site Plan (using Chain & tape, Prismatic compass, Plane table,
Levelling instrument, Theodolite and Total Station), field book entry, plotting, mapping, calculation
of area, by using different survey instrument and observation of all safety aspects is mandatory.
The safety aspects covers components like OSH&E, PPE, Fire extinguisher, First Aid and in addition
5S being taught.
Carpentry; Identification of timber and perform sawing and planning using hand and power
tools.Sharpening and setting of saw bladeand planer blade/ cutter, surface finishing with exact
sizing by planning operation. Preparation of different wooden Joints. (Range of skill - framing joint,
Housing joints, broadening joints, Lengthening joints), Making of wooden job as per drawing with
timber or alternatives of timber i.e. FRP, MDF, FOAM. Making of doors and windows.
Electrical;Joining of electrical wire and carry out soldering, crimping. Electrical wiring with fixing of
accessories conforming ISI rules ( Range of skills - different types of Electrical wiring, joining of
Fuses,fixing of MCB, connection of lamp with switch and different fitting, etc.), Installation of
electrical appliances, Earthing and estimate costing of wiring. Identify different types of
transformers, test and use.
4
Civil Engineering Assistant
Plumbing;pipe connection demonstrating use of Plumbing Tools. joining of pipes with different
methods. Cutting and joining of pipes using different types of fittings. Preparation of layout of soil
pipe and waste pipe with different types of sanitary fittings. installation of water meter and
removal of air lock. Preparation of water supply system in residential buildings using different types
of valves, fittings and appliances are being taught.In addition students are being taught to create
objects on 3D modeling concept in CAD.
SECOND YEAR: Concrete Technology; Test and analysis of cement, aggregate, sand, effect of
water cement ratio. Preparation of concrete, carry out form work and reinforcement with the
application of modern Power Tools. Preparation of reinforcement of different R.C.C. members i,e,
Foundation, beams, columns, slabs, Retaining Wall, etc. Erection of scaffolding and making of
intricate form work at different locations. Bar bending and preparation of bar bending schedule
and calculation of estimated quantity of materials. Making of shuttering & supports for making
different types of arches and lintels with chajja. Lay out different types of vertical movement
according to shape, location, materials by using stair, lift, ramp and escalator are being taught.
Project Work, Estimating Costing, Maintenance & Management; On site practical training of
piling. Preparation of Single Storied Residential Building Plan as per local by law using CAD.
Preparation of drawing with ArchiCAD and 3D Max for Solid Modeling of Architectural / Civil 3D
Drawing.Preparation of Solid Modeling of Architectural /Civil 3D Drawing using 3d Max and Revit
software, Creating 3D model from 2D plane, Lighting and rendering, Quantity calculation of
materials using BIM software like Revit, Preparation of rate analysis of different item of works with
detailed Specification. Calculation of floor area and carpet area, Preparation of detail estimate of
building by centre line method and separate wall method,calculation of quantities of materials
involved and preparation of abstract cost for the works. Performing repair Plastering, white
washing, painting flooring, replacing of glass, repolishing of floor, stain removal from floor, wooden
works. Field training of Foundation failure, Strengthening of foundation, Rectification of leaking
roof, repair of expansion joint. Pre construction and Postconstruction anti - termite treatment and
Market survey for different materials used in anti termite treatment. Layout of house plumbing and
drainage plan, repairing of service main, waist outlet cleaning of sanitary installation, scrapping and
painting of pipes of a new site. Field Training on use of Adhesive in timber, tile fixing, jointing in
concrete, joint filler & sealing compound. Field Training on different types of construction
equipments in Excavation, Hoisting, Conveying, Drilling. Construction Management training i.e.
manpower, materials, machines and economy are being taught to work as an assist of civil
engineer and perform as Site Supervisor.
5
Civil Engineering Assistant
2. TRAINING SYSTEM
2.1 GENERAL
The Directorate General of Training (DGT) under Ministry of Skill Development &
Entrepreneurship offers a range of vocational training courses catering to the need of different
sectors of the economy/ labour market. The vocational training programs are delivered under the
aegis of Directorate General of Training (DGT). Craftsman Training Scheme (CTS) with variantsand
Apprenticeship Training Scheme (ATS) are two pioneer programs of DGT for propagating
vocational training.
Civil Engineering Assistant trade under CTS is one of the popular courses delivered
nationwide through network of ITIs. The course is of two-years duration. It mainly consists of
Domain area and Core area. The Domain area (Trade Theory & Practical) impart professional skills
and knowledge, while Core area (Employability Skills) impart requisite core skill, knowledge and
life skills. After passing out the training program, the trainee is awarded National Trade Certificate
(NTC) by DGT which is recognized worldwide.
Read & interpret technical parameters/documentation, plan and organize work processes,
identify necessary materials and tools;
Perform work with due consideration to safety rules, Govt. Bye laws and environmental
protection stipulations;
Apply professional knowledge, core skills & employability skills while performing the work
Check the work as per sketches and rectify errors.
Document the technical parameters related to the work undertaken.
Can join industry as Technician and will progress further as Senior Technician, Supervisor
and can rise up to the level of Manager.
Can become Entrepreneur in the related field.Start own agency for construction
equipments contract /own building maintenance contract
Can take admission in Diploma course in notified branches of Engineering by lateral entry.
Can join Apprenticeship programme in different types of industries leading to National
Apprenticeship certificate (NAC).
Can join Crafts Instructor Training Scheme (CITS) in the trade for becoming an instructor in
ITIs.
6
Civil Engineering Assistant
Can join as Assistant supervisor in construction site of high Rise Buildings/Architect's
office/Builders.
Can join advanced Diploma (Vocational) courses under DGT as applicable.
Table below depicts the distribution of training hours across various course elements
during a period of two-years: -
Every year 150 hours of mandatory OJT (On the Job Training) at industry, wherever not
available then group project is mandatory.
Trainees of one-year or two-year trade can also opt for optional courses of up to 240 hours in
each year for 10th/ 12th class certificate along with ITI certification, or, add on short term courses.
The trainee will be tested for his skill, knowledge and attitude during the period of course
through formative assessment and at the end of the training programme through summative
assessment as notified by the DGT from time to time.
a) The Continuous Assessment(Internal) during the period of training will be done by Formative
Assessment Method by testing for assessment criteria listed against learning outcomes. The
training institute has to maintain individual trainee portfolio as detailed in assessment guideline.
7
Civil Engineering Assistant
The marks of internal assessment will be as per the formative assessment template provided on
www.bharatskills.gov.in
b) The final assessment will be in the form of summative assessment. The All India Trade Test for
awarding NTC will be conducted by Controller of examinations, DGT as per the guidelines. The
pattern and marking structure is being notified by DGTfrom time to time. The learning outcome
and assessment criteria will be basis for setting question papers for final assessment. The
examiner during final examination will also check individual trainee’s profile as detailed in
assessment guideline before giving marks for practical examination.
For the purposes of determining the overall result, weightage of 100% is applied for six
months and one year duration courses and 50% weightage is applied to each examination for two
years courses. The minimum pass percent for Trade Practical and Formative assessment is 60% &
for all other subjects is 33%.
Appropriate arrangements should be made to ensure that there will be no artificial barriers
to assessment. The nature of special needs should be taken into account while undertaking the
assessment. Due consideration should be given while assessing for teamwork,
avoidance/reductionofscrap/wastage and disposal of scrap/waste as per procedure, behavioral
attitude, sensitivity to the environment and regularity in training. The sensitivity towards OSHE
and self-learning attitude are to be considered while assessing competency.
8
Civil Engineering Assistant
(c) Marks in the range of more than 90% to be allotted during assessment
For performance in this grade, the candidate, High skill levels in the use of hand
with minimal or no support in organization tools, machine tools and workshop
and execution and with due regard for safety equipment.
procedures and practices, has produced work Above 80% accuracy achieved while
which demonstrates attainment of a high undertaking different work with those
9
Civil Engineering Assistant
standard of craftsmanship. demanded by the component/job.
A high level of neatness and
consistency in the finish.
Minimal or no support in completing
the project.
10
Civil Engineering Assistant 3. JOB ROLE
Civil Engineering Technicians; includes all other Civil Engineering Technicians engaged in
construction, survey, and related fields of civil engineering, not elsewhere classified.
Reference NCO-2015:
Reference NOS: --
PCS/N9446
PCS/N9447
PCS/N9448
PCS/N9449
PCS/N9450
PCS/N9451
PCS/N9452
PCS/N9453
PCS/N9454
PCS/N9455
PCS/N9456
PCS/N9457
PCS/N9458
PCS/N9459
PCS/N9460
PCS/N9461
11
Civil Engineering Assistant
PCS/N9462
PCS/N9463
PCS/N9464
PCS/N9465
MIN/ N0454
MIN/ N0454
MIN/ N0454
PCS/N9466
PCS/N9467
MIN/N3102
MIN/N3102
MIN/N3102
MIN/N3104
MIN/N3105
MIN/N3101
MIN/N3102
MIN/N3103
MIN/N3208
PCS/N9468
PCS/N9469
PCS/N9470
PCS/N9471
PCS/N9472
PCS/N9473
PCS/N9474
PCS/N9475
PCS/N9476
PCS/N9477
PCS/N9478
PCS/N9479
PCS/N9480
PCS/N9481
PCS/N9482
PCS/N9483
PCS/N9484
PCS/N9485
PCS/N9486
PCS/N9487
PCS/N9488
PCS/N9489
PCS/N9490
PCS/N9491
PCS/N9492
12
Civil Engineering Assistant
4. GENERAL INFORMATION
Eligibility forPwD LD, CP, LC, DW, AA, LV, DEAF, AUTISM, SLD, MD
Unit Strength (No. of
24 (There is no separate provision of supernumerary seats)
Student)
13
Civil Engineering Assistant
Essential Qualification:
Relevant National Craft Instructor Certificate (NCIC) in any of
the variants under DGT.
Essential Qualification:
Regular / RPL variants of National Craft Instructor Certificate
(NCIC) in relevant trade
OR
14
Civil Engineering Assistant
Regular / RPL variants NCIC in RoDA or any of its variants under
DGT
(iii) Engineering Drawing B.Voc/Degree in Engineering from AICTE/UGC recognized
Engineering College/ university with one-year experience in the
relevant field.
OR
03 years Diploma in Engineering from AICTE / recognized board
of technical education or relevant Advanced Diploma
(Vocational) from DGT with two years’ experience in the
relevant field.
OR
NTC/ NAC in any one of the Mechanical group (Gr-I) trades
categorized under Engg. Drawing’/ D’man Mechanical / D’man
Civil’ with three years’ experience.
Essential Qualification:
Regular / RPL variants of National Craft Instructor Certificate
(NCIC) in relevant trade
OR
Regular / RPL variants of NCIC in RoDA / D’man (Mech /civil) or
any of its variants under DGT.
(iv) Employability Skill MBA/ BBA / Any Graduate/ Diploma in any discipline with Two
years’ experience with short term ToT Course in Employability
Skills.
(Must have studied English/ Communication Skills and Basic
Computer at 12th / Diploma level and above)
OR
Existing Social Studies Instructors in ITIs withshort term ToT
Course in Employability Skills.
(v) Minimum Age for 21 Years
Instructor
15
Civil Engineering Assistant
5. LEARNING OUTCOME
Learning outcomes are a reflection of total competencies of a trainee and assessment will be
carried out as per the assessment criteria.
16
Civil Engineering Assistant
22. Demonstrate surface finish with exact sizing by planning operation. MIN/ N0454
23. Prepare different wooden Joints. (Range of skill - framing joint, Housing joints, broadening
joints, Lengthening joints ) MIN/ N0454
24. Make small wooden job as per drawing with schedule sizes of timber or alternatives of
timber i.e. FRP, MDF, FOAM using various hardware. PCS/N9466
25. Make different types of doors and windows with fixing of component. PCS/N9467
26. Demonstrate joining of electrical wire and carry out soldering, crimping observing related
safety precautions. MIN/N3102
27. Demonstrate Electrical wiring with fixing of accessories conforming ISI rules.( Range of
skills - different types of Electrical wiring, joining of Fuses, fixing of MCB, connection of
lamp with switch and different fitting, etc.) MIN/N3102
28. Demonstrate installation of electrical appliances, Earthing and estimate costing of wiring.
MIN/N3102, MIN/N3104, MIN/N3105
29. Identify different type of transformers and test and use. MIN/N3101, MIN/N3102,
MIN/N3103
30. Prepare a Simple pipe connection demonstrating cutting, joining of pipe with different
method using different types of fittings. MIN/N3208
31. Prepare layout of soil pipe and waste pipe with different types of sanitary fittings.
PCS/N9468
32. Prepare a water supply system in residential buildings using different types of
valves,fittings and appliances. PCS/N9469
33. Create objects on 3D modeling concept in CAD. PCS/N9470
34. Demonstrate basic mathematical concept and principles to perform practical operations.
Understand and explain basic science in the field of study. PCS/N9471
SECOND YEAR
35. Demonstrate test and analysis of cement, aggregate, sand, effect of water cement ratio.
PCS/N9472
36. Prepare concrete, carry out simple form work and reinforcement with the application of
modern Power Tools. PCS/N9473
37. Prepare reinforcement of different R.C.C. members i,e, Foundation, beams, columns, slabs,
Retaining Wall, etc. PCS/N9474
38. Erect scaffolding and make intricate form work at different locations. PCS/N9475
39. Prepare a bar bending schedule and demonstrate bar bending and calculate the estimated
quantity of materials. PCS/N9476
40. Make different types of arches and lintels with chajja. PCS/N9477
41. Lay out different types of vertical movement according to shape, location, materials by
using stair, lift, ramp and escalator. PCS/N9478
17
Civil Engineering Assistant
42. Explain pile foundation. PCS/N9479
43. Prepare a Single Storied Residential Building Plan as per local by law using CAD. PCS/N9480
44. Demonstrate ArchiCAD and 3D Max for Solid Modeling of Architectural / Civil 3D Drawing.
PCS/N9481
45. Prepare Solid Modelling of Architectural /Civil 3D Drawing using 3d Max and Revit
software. PCS/N9482
46. Work out rate analysis of different item of works with detailed Specification. PCS/N9483
47. Prepare a detail estimate of one room building by centre line method and separate wall
method, calculate the quantities of materials involved from the above estimated
quantities& prepare a abstract of cost for the above item of works. PCS/N9484
48. Perform repair Plastering, white washing, painting flooring, replacing of glass, repolishing
of floor, stain removal from floor, wooden works. PCS/N9485
49. Perform field training of Foundation failure, Strengthening of foundation, Rectification of
leaking roof, Repair of expansion joint. PCS/N9486
50. Demonstrate anti - termite treatment and Market survey for different materials used in
anti termite treatment. PCS/N9487
51. Layout of house plumbing and drainage plan, repairing of service main, waist outlet
cleaning of sanitary installation, scrapping and painting of pipes of a new site. PCS/N9488
52. Demonstrate use of Adhesive in timber, tile fixing, jointing in concrete, joint filler & sealing
compound. PCS/N9489
53. Demonstrate different types of construction equipments in Excavation, Hoisting,
Conveying, Drilling. PCS/N9490
54. Demonstrate Construction Management i.e. manpower, materials, machines and economy.
PCS/N9491
55. Demonstrate basic mathematical concept and principles to perform practical operations.
Understand and explain basic science in the field of study. PCS/N9492
18
Civil Engineering Assistant
6. ASSESSMENT CRITERIA
FIRST YEAR
1. Prepare free hand Ensure data and information received are sufficient for preparation
sketches of hand tools of drawing.
used in civil work with Sketch horizontal lines from left to right, vertical lines downward,
proper layout and folding inclined lines in different angles by freehand.
of drawing sheets Draw freehand sketches of tools (viz. hoe, head pan, trowel,
following safety wooden float, plumb bob, sand screener).
precaution. PCS/N9446 Check the drawings to confirm their compliance with the
supplied design / object.
19
Civil Engineering Assistant
provide details in the drawings.
(a) Prepare lettring in full scale 25 mm. height size in Vertical &
Italic system in 7:4 & 5:4 single stroke & double stoke method both
in small & Capital letter.
(b) Prepare Numbering in full scale 25 mm. height size in Vertical &
Italic system in 7:4 & 5:4 single stroke & double stoke method both.
(c) Draw different figures showing different dimensioning system
Aligned & Unidirectional.
Check the drawings to confirm their correctness.
3. Construct plain scale, Read and interpret the drawing requirements. Ensure data and
comparative scale, information received are sufficient for preparation ofdrawing.
diagonal scale and vernier Draw different types of scales.
scale. PCS/N9448 Find out R.F of the scale, calculate the length of scale on drawing.
Construct plain scales, comparative scales, diagonal scales
andvernierscales,mark the distance on the scale.
Check the drawings to confirm their correctness.
4. Draw orthographic Read and interpret the drawing requirements. Ensure dataand
projections of different information received are sufficient for preparation ofdrawing.
objects with proper lines Carry out necessary calculations to compute dimensions of Various
and dimensioning. components/ parts of drawings.
PCS/N9449 (a) develop view in orthographic projection by placing object
between horizontal and vertical plane of axes,
(b) generate side view of blocks in different inclination on VP and
HP by auxiliary vertical plane.
(a) write name of the drawing on heading at centre alignment,
(b) write individual title for every projection drawing,
(c) construct drawing views, construction lines and dimension lines
as per standard.
Check the drawings to confirm their compliance with the supplied
design / object.
Draw orthographic projection of line in different plane and in
different Position.
Draw orthographic projection of Plane figure in different plane and
in different Position.
Draw orthographic projection of Solid figure in different plane and
20
Civil Engineering Assistant
in different Position.
Draw orthographic projection of Section of Solid in different
plane and in different Position.
5. Draw Isometric, oblique Read and interpret the drawing requirements. Ensure dataand
and perspective views of information received are sufficient for preparation ofdrawing.
different solid, hollow and Carry out necessary calculations to compute dimensions ofVarious
cut sections with proper components/ parts of drawings.
lines and dimensions as construct an Isometric scale to a given length. draw the isometric
per standard convention. projection of regular solids.
PCS/N9450 Draw the isometric views for the given solids with hollow and
cut sections.
Draw three views of different isomertic objects to
Orthoghraphic.
Draw the oblique views for the given solids with hollow and
cut sections.
Draw the perspective views for the given solids with hollow and
cut sections.
Check the drawings to confirm their compliance with the
supplied design / object.
6. Draw component parts of Read and interpret the drawing requirements such as rough
a single storied residential sketches, specifications, drawing brief, RFD etc. ensure data and
building with suitable information received are sufficient for preparation of drawing.
symbol and scales. Construct parts of a building and list the sequence of construction.
PCS/N9451 Draw and indicate the levels of different parts of building.
Draw dressing and varieties of finishes, artificial stones, natural bed
of stone.
Draw RCC used in different component parts of a building.
Draw timber joints used in doors, windows and arches.
Draw steel framing for pre-cast concrete.
Use codes and other references that follow the required
conventions.
Draw the appropriate signs and symbols for showing different
types of openings used in drawing.
Draw the signs and symbols of various types of doors windows and
ventilators.
21
Civil Engineering Assistant
Check the drawings to confirm their compliance with the upplied
design / object.
7. Create objects on CAD Ensure that computer system is correctly operating. Check that
workspace using allrequired peripheral devices are connected and correctly
Toolbars, Commands, operating.
Menus, formatting layer Start up the software and adjust the page size, measurementunit,
and style. PCS/N9452 scale and plot area before staring the work.
Set drawing parameters like, colour, layer, line type, lineweight,
text font etc. prepare title block for the drawing covering
specification required.
Draw 2D drafting by using CAD toolbars and from set oftool icons in
ribbon.
Draw drawing using sortcut keyboard command, creating
templates, inserting drawings, Layers, Modify Layers.
Customize Dimension and Text styles.
Provide title and dimension on object drawing.
Add Symbols and specifications and use codes and other
references as per the drawing requirement.
Check drawings to confirm their compliance with the required
design.
Create layout space and viewports.
Plot the drawing with required scale.
8. Identify different types of Identify different types of building materials i.e. Stones, Bricks,
building materials i.e. Lime, Pozzolanic, Cement, Sand, Clay Products, Mortar.
Stones, Bricks, Lime, Carry out task according to their characteristic, types, use &
Pozzolanic, Cement, Sand, function in different civil engineering structure.
Clay Products, Mortar
their characteristic, types,
use & function.
PCS/N9453
9. Mark different types of Read and interpret the drawing, ensure data and information
Foundation and Set out received are sufficient for completion of task.
Foundation trenches. carry out necessary calculations to compute dimensions of Various
PCS/N9454 components/ parts of drawings.
22
Civil Engineering Assistant
Mark different types of shallow and deep foundation.
(a) Mark footing for column,
(b) Mark footings for wall,
(c) Mark stepped foundation and inverted arch foundation,
(a) Mark grillage foundation
(b) Mark raft foundation
(a) Mark various types of pile foundation,
(b) Mark pier foundation,
(c) Mark well foundation (caisson),
Check markings to confirm their compliance with thesupplied
drawing.
10. Demonstrate different Read and interpret the drawing, ensure data and information
types of brick masonry received are sufficient for completion of task.
and Tools used in Arrange required materials to construct a wall.
different bonds.Perform Perform construction of wall –
construction of wall - (a) header bond,
header bond, stretcher (b) stretcher bond,
bond, English bond, (c) English bond,
Flemish bond. PCS/N9455 (d) Flemish bond .
Check the work to confirm their compliance with the supplied
drawing.
11. Perform different types of Plan for different types of Plastering & Pointing.
Plastering & Pointing, Arrange required materials to perform different types of Plastering
rendering & wall cladding. & Pointing, rendering & wall cladding.
PCS/N9456 prepare surface for plastering, rendering & wall cladding.
Perform different types of Plastering & Pointing, rendering & wall
cladding.
Examine defects and demonstrate remedies of plastering.
Check the work to confirm their compliance with therequired
quality.
12. Identify the different Identify different types of Protective materials i.e. Paint, Varnish,
types of Protective etc.
materials i.e. Paint, Plan for application of different types of Protective materials.
Varnish and their Arrange required materials for application of different types of
23
Civil Engineering Assistant
application. PCS/N9457 Protective materials.
prepare surface for application of different types of Protective
materials.
Perform application of different types of Protective materials.
Examine defects and demonstrate remedies in application of
different types of Protective materials.
Check the work to confirm their compliance with thereqired quality.
13. Demonstrate Damp Proof Read and interpret the drawing and ensure data and information
Course in different received are sufficient for D.P.C. in different position.
position. PCS/N9458 Plan to perform D.P.C. in different position.
Arrange required materials to perform D.P.C. in different position.
prepare location to perform D.P.C. in different position.
Perform D.P.C. in different position.
a. damp proofing in basement.
b. damp proofing in external wall
c. damp proofing in internal walls
d. damp proofing by cavity wall.
e. damp proofing in flat roof and parapet wall.
f. damp proofing of flat roof by tar felting
g. damp proofing by mud phuska terracing with tile,
h. damp proofing in pitched roof.
Examine defects and demonstrate remedies in D.P.C. and termite
treatment.
Check the work to confirm their compliance with therequired
quality.
14. Prepare different types Read and interpret the drawing and ensure data and information
of Flooring. PCS/N9459 received are sufficient for flooring in different position.
Plan to perform flooring in different position.
Arrange required materials to perform flooring in different position.
prepare location to perform flooring in different position.
Perform flooring in different position:
a. flooring on timber ground floor,
b. flooring on brick floor,
c. flooring on flag stone,
d. flooring on concrete floor,
24
Civil Engineering Assistant
e. flooring on terrazzo floor,
f. flooring of mosaic floor,
g. flooring by Tiles Floor,
h. flooring on single joist timber floor.
Examine defects and demonstrate remedies in flooring.
Check the work to confirm their compliance with therequired
quality.
25
Civil Engineering Assistant
Add specifications and use codes and other references as perthe
drawing requirements.
Check drawings to confirm their compliance with the
required plan.
20. Perform a site survey with Interpret the drawing requirements.orientation-collect data-repeat
Total Station and prepare same procedure at each stations.
site plan. PCS/N9465 Adjust and fix the Total Station in an station point.
Conduct reconnaissance survey-prepare key plan.
Prepare reference sketches.
26
Civil Engineering Assistant
Conduct traverse survey-set up the instrument over the first
station-set job-set station-orient-collect data-take foresight to next
station-shift instrument to next station-set up-back.
Download and process the data, prepare plan/map.
Measure remote distance and elevation.
Calculate 2D / 3D area on field/site.
Calculates surface volume of field/site.
Add specifications and use codes and other references as per the
drawing requirements.
Check drawings to confirm their compliance with the required one.
21. Identify timber and Identify different wooden sample piece i.e.- soft wood & hard
perform sawing and wood, wooden grains etc. & their applications.(Annual ring, knots,
planning using hand and shakes & chicks etc.)
power tools. MIN/ N0454 Demonstrate application of hand tools, measuring tools, and work
holding devices.
Demonstrate use of different power tools, viz. saws, drills, etc.
Perform sawing, planning,Moulding, Rebating, Chamfering, etc.
using different types of saws, and plains.
Sharpen and set different type saw bladeand planer blade/ cutter.
Check the product to confirm their compliance with the desired
one.
23. Prepare different wooden Read and Interpret the drawing requirements.
Joints. (Range of skill - Carry out necessary calculations to compute dimensions of Various
framing joint, Housing components/ parts.
joints, broadening joints, Ascertain required timber, tools and other materials to carry out
27
Civil Engineering Assistant
Lengthening joints). MIN/ the performance.
N0454 Make framing joint - Mortise and tenon Joint (Single and double,
Plain hunched, Mitre corner).
Make Housing joints - Full housing, Bridle, Stopped housing.
Make broadening joints - Simple butt joint, Riveted butt joint, etc.
Make Lengthening joints:End half lap joint, End over lap joint, End
bends lap joint,slopping scarf, racking scared, half lapping scarf,
table scarf joint etc.
Check joints to confirm their compliance with the required design.
24. Make small wooden job Read and Interpret the drawing requirements.
as per drawing with Carry out necessary calculations to compute dimensions of Various
schedule sizes of timber components/ parts.
or alternatives of timber Ascertain required timber, tools and other materials to carry out
i.e. FRP, MDF, FOAM the performance.
using various hardware. Perform making of wooden job as per drawing.
PCS/N9466 Check the job to confirm their compliance with the required design.
25. Make different types of Read and Interpret the drawing requirements.
doors and windows with Carry out necessary calculations to compute dimensions of Various
fixing of component. components/ parts.
PCS/N9467 Ascertain required timber, tools and other materials to carry out
the performance.
Perform making of different Types doors including panelled, glazed
and flush door as per drawing.
Perform making of Different types windows and ventilators as per
drawing.
Check the job to confirm their compliance with the required
design.
28
Civil Engineering Assistant
crimping.
Perform simple twist, married, Tee and western union joints.
Perform britannia straight, britannia Tee and rat tail joints.
Perform Soldering of joints / lugs.
Check the job to confirm their compliance with the required design.
29. Identify different type of Read and Interpret the drawing requirements.
transformers and test and Carry out necessary calculations to ascertain required wire,
use. MIN/N3101, transformer and arrange required tools and other materialsto carry
MIN/N3102, MIN/N3103 out the performance.
Identify transformer, test and install.
Check the performance to confirm its compliance with the
requirement.
29
Civil Engineering Assistant
30. Prepare a Simple pipe Read and Interpret the drawing requirements.
connection Carry out necessary calculations to ascertain required pipe and
demonstrating cutting, arrange required tools and other materialsto carry out the
joining of pipe with performance.
different method using Perform cutting, threading, drilling and taping on pipe.
different types of fittings. Prepare a simple pipe connection using different pipe fittings and
MIN/N3208 joints.
Perform Joining of pipe with thread joint.
Perform Joining of pipe with lead joint.
Perform Joining of pipe with flange joint.
Perform Joining of pipe with cement joint.
Perform Joining of pipe with D. Joint etc.
Perform Fixing of ferrule on pipe.
Check the performance to confirm its compliance with the
drawing.
31. Prepare layout of soil pipe Read and Interpret the drawing requirements.
and waste pipe with Carry out necessary calculations to ascertain required pipe, sanitary
different types of sanitary fittings and arrange required tools and other materialsto carry out
fittings. PCS/N9468 the performance.
Prepare Layout of soil pipe and waste pipe with different sanitary
fitting.
Perform fitting of I.W.C with high level cistern.
Perform fitting of washbasin.
Perform fitting of E.W.C. with low level cistern.
Perform fitting of kitchen sink.
Perform fitting of bath tub.
Perform fitting of urinal pot with auto cistern.
Check the performance to confirm its compliance with the
drawing.
32. Prepare a water supply Read and Interpret the drawing requirements.
system in residential Ascertain requirement of pipes, valves,fittings and appliances and
buildings using different arrange required tools and other materialsto carry out the
types of valves,fittings performance.
and appliances. Perform installation of water meter.
30
Civil Engineering Assistant
PCS/N9469 Demonstrate removal of air lock.
Demonstrate determination of pH by pH meter. Analysis and
treatment of Effluent water.
Demonstrate reconditioning of taps, valves & flushing tank and test
for correct functioning.
Prepare a water supply pipe line system in residential buildings
using different types of valves, fittings and appliances.
Check the performance of water supply system.
36. Prepare concrete, carry Read and Interpret the drawing requirements.
out simple form work and Plan for Preparation of concrete, carring out form work and
reinforcement with the reinforcement.
31
Civil Engineering Assistant
application of modern Demonstrate Batching, Mixing, Transportation, Placing and
Power Tools. PCS/N9473 Compaction.
Demonstrate all operations taking necessary precautions
related to from work and reinforcement.
Prepare concrete and lay at required place using power tools.
Demonstrate Curing and Finishing.
Test strength of concrete.
Demonstrate removal of form work.
38. Erect scaffolding and Read and Interpret the drawing requirements.
make intricate form work Plan for Erection of scaffolding and making intricate form work.
at different locations. Select appropriate material for form work at different locations.
PCS/N9475 Erect scaffolding & make form work at different locations.
Check, Identify defects & rectify form work.
39. Prepare a bar bending Read and Interpret the drawing requirements.
schedule and Make a plan for bar bending.
demonstrate bar bending Prepare a bar bending schedule of different RCC members.
32
Civil Engineering Assistant
and calculate the Demonstrate different operations in bar bending –
estimated quantity of a. straightening of bars,
materials. PCS/N9476 b. cutting of bars,
c. bending of bars,
d. placing of bars,
e. binding of bars,
f. fixing of cover blocks.
Make an estimate for quantity of steel and binding wire required
for a given job.
Check to confirm their compliance with the drawing.
40. Make different types of Read and Interpret the drawing requirements.
arches and lintels with Plan for makingdifferent types of arches and lintels with chajja.
chajja. PCS/N9477 Demonstrate making of shuttering & supports with uprights
and wedges for Arches, Lintels and Lintels with Chajjahs.
Demonstrate cutting, bending & placing of reinforcement.
Demonstrate mixing, placing & compacting concrete.
Demonstrate spanning of opening with a semi-circular arch, making
centering, cutting of templates for voussoirs&preparing voussoirs,
setting uprights of arch.
Demonstrate Construction of arch & removing centering.
41. Lay out different types of Read and Interpret the drawing requirements for vertical
vertical movement movements.
according to shape, Plan for making lay out of different types of vertical movement
location, materials by according to shape, location, materials.
using stair, lift, ramp and Demonstrate Lay out of straight stairs made of wood.
escalator. PCS/N9478 Demonstrate Lay out of open well stairs made of brick.
Demonstrate Lay out of dog- legged stairs made of steel.
Demonstrate Lay out of geometrical and bifurcated stairs made of
RCC.
Demonstrate Lay out of spiral stairs made of steel.
Demonstrate Lay out of Lift and Escalator.
Check lay out to confirm their compliance with the required design.
42. Explain pile foundation. Read and Interpret the drawing requirements for pile
PCS/N9479 foundation.
33
Civil Engineering Assistant
Make a plan for pile foundation.
Make a schedule for materials required for pile foundation.
Prepare a lay out of pile foundation as per drawing.
43. Prepare a Single Storied Read and interpret the drawing requirements such as
Residential Building Plan roughsketches, specifications, drawing brief, RFD etc. ensure
as per local by law using dataand information received are sufficient for preparation
CAD. PCS/N9480 ofdrawing.draw size and position of rooms, wall thickness and
number of openings.
Carry out necessary calculations to compute dimensions of
Various components/ parts of drawings.
Draw the line diagram of the Single Storied residential building.
(a) develop the sectional plan of building
(b) Prepare sectional elevation as per the section plan
(c) draw the elevation of building.
(d) prepare working drawing of the building.
Draw various interior and exterior furnishings details of a Single
Storied residence.
Create a site plan showing details.
Prepare a key / location plan.
Prepare area statement.
Add Symbols and specifications and use codes and other
references as per the drawing requirements.
Check drawings to confirm their compliance with the required
design.
44. Demonstrate ArchiCAD Demonstrate ArchiCAD and 3D Max for Solid Modelling of
and 3D Max for Solid Architectural / Civil 3D Drawing.
Modelling of Architectural Apply Software in Civil Engineering field to prepare drawing with
/ Civil 3D Drawing. ArchiCAD and 3D Max for Solid Modelling of Architectural / Civil 3D.
PCS/N9481 Check drawings to confirm their compliance with the required
design.
45. Prepare Solid Modelling Read and interpret the drawing requirements such as
of Architectural /Civil 3D roughsketches, specifications, drawing brief, RFD etc. ensure
Drawing using 3d Max dataand information received are sufficient for preparation
and Revit software. ofdrawing.
34
Civil Engineering Assistant
PCS/N9482 Carry out necessary calculations to compute dimensions of Various
components/ parts of drawings.
Prepare 3D model using 3d Max software.
Create 3D model from 2D plane.
Make Lighting and rendering.
Prepare material editor using BIM software like Revit.
Calculate quantity of materials.
46. Work out rate analysis of Read and interpret the drawing requirements, specifications, etc.
different item of works ensure data and information received are sufficient for preparation
with detailed of rate analysis.
Specification. PCS/N9483 Carry out necessary calculations to compute estimation and cost
analysis.
Calculate floor area and carpet area.
Calculate FAR.
Preapare rate analysis and identify the units of measurement.
Calculate quantities of materials and prepare rate analysis from
standard data.
Calculate quantities of labour required for different item of work
from standard data.
Calculate the rate per unit of works of different items including
labour charges from schedule of rate.
Prepare rate analysis of works for Plant machinery.
Prepare rate analysis of works for over head charge, Profit with the
details specification.
Check rate analysis to confirm their compliance with the design.
47. Prepare a detail estimate Read and interpret the drawing requirements, specifications, etc.
of one room building by ensure data and information received are sufficient for preparation
centre line method and of estimation.
separate wall method, Carry out necessary calculations to compute estimation and cost
calculate the quantities of analysis.
materials involved from Prepare detailed estimate of a building by centre line method and
the above estimated separate wall method.
quantities& prepare a Prepare a detailed estimate for – boundary wall, septic
abstract of cost for the tank,underground and overhead reservoir.
above item of works. Calculate the quantities of materials in the standard format.
35
Civil Engineering Assistant
PCS/N9484 Prepare abstract of estimate.
Check estimation and cost analysis to confirm their compliance with
the design.
48. Perform repair Plastering, Identify the cracks and defect of Plastering, walls for white washing
white washing, painting and painting, area for flooring, replacing of glass, repolishing of
flooring, replacing of floor, stain removal from floor, wooden works and remedy of the
glass, repolishing of floor, defects.
stain removal from floor, Prepare estimation and cost analysis for the identified work.
wooden works. Make scaffolding for plastering or white washing.
PCS/N9485 Demonstrate removal of cracks and defect of Plastering.
Perform white washing and painting on walls.
Demonstrate removal of cracks and defect of flooring
Perform replacing of glass.
Demonstraterepolishing of floor and stain removal from floor.
Demonstrate wooden works and remedy of the defects.
49. Perform field training of Identify the Foundation failure, defects in structure, leaking roof,
Foundation failure, defects in expansion joint.
Strengthening of Prepare estimation and cost analysis for the identified work.
foundation, Rectification Demonstrate Strengthening of foundation.
of leaking roof, Repair of Demonstrate repairing of defects in structure.
expansion joint. Perform rectification of leaking roof.
PCS/N9486 Demonstrate repair of expansion joint.
51. Layout of house plumbing Layout the house plumbing and drainage plan.
36
Civil Engineering Assistant
and drainage plan, Plan for repairing of service main, waist outlet cleaning of sanitary
repairing of service main, installation, scrapping and painting of pipes.
waist outlet cleaning of Demonstrate house plumbing and drainage.
sanitary installation, Perform repairing of service main, waist outlet cleaning of sanitary
scrapping and painting of installation.
pipes of a new site. Demonstrate scrapping and painting of pipes.
PCS/N9488 Prepare estimation and cost analysis for the identified work.
Check the work to confirm their compliance with the reqired
quality.
37
Civil Engineering Assistant
Understand and explain
basic science in the field
of study. PCS/N9492
7. TRADE SYLLABUS
FIRST YEAR
Reference Professional Skills
Professional Knowledge
Duration Learning (Trade Practical)
(Trade Theory)
Outcome With Indicative Hours
Professional Prepare free 1. Importance of trade Importance of safety and
Skill 18 Hrs; hand sketches of training, general precautions observed
hand tools used demonstrate tools & in the in the industry/shop
Professional in civil work with equipments used in the floor. All necessary guidance
Knowledge proper layout and trade. (1 hrs) to be provided to the new
04 Hrs folding of 2. Importance of comers to become familiar
drawing sheets housekeeping & good with the working of Industrial
following safety shop floor practices. (1 Training Institute system
precaution. hrs) including stores procedures.
(Mapped NOS: 3. Occupational Safety Soft Skills: its importance and
PCS/N9446 ) &Health :Introduction to Job area after completion of
safety equipments and training.
their uses. Introduction of Introduction of First aid.
first aid. Health, Safety Introduction of PPEs.
and Environment Introduction to 5S concept&
guidelines, legislations & its application.
regulations as applicable. Response to emergencies
(2 hrs) e.g.; power failure, fire alarm,
4. Disposal procedure of etc.(02 hrs)
waste materials of the
trade. (1 hrs)
38
Civil Engineering Assistant
5. Personal protective
Equipments(PPE):-Basic
injury prevention, Basic
first aid. (1 hrs)
6. Hazard identification and
avoidance, safety signs for
Danger, Warning, caution
& personal safety
message.
(1 hrs)
7. Preventive measures for
electrical accidents&steps
to be taken in such
accidents. (2 hrs)
8. Use of Fire extinguishers.
(1 hrs.)
9. Awareness about the job Familiarisation&
sheets made by the ex. information about rules
trainees. (1 hrs) and regulations of the
10. Use of drawing Institute and Trade.
instruments and Overview of the subjects
equipment with care. (1 to be taught for each year.
hrs) List of the Instruments,
11. Method of fixing of equipments and materials
drawing sheet on the to be used during
drawing board. (1 hrs) training.(02 hrs)
12. Layout of different size of
Drawing sheets and
folding of sheets. (2 hrs)
13. Draw free hand sketch of
hand tools used in civil
work.(3 hrs)
Professional Prepare Symbols, 14. Symbols &conventional Importance of B.I.S.
Skill 15 Hrs; Lettering, representation for Introduction of Code for
Numbering, materials in sections as practice of Architectural
Professional plane figure per IS 962-1989, SP- and Building Drawings (IS:
Knowledge applying drawing 46:2003 for building 962-1989, SP-46:2003).
06 Hrs instruments and drawings. (04 hrs) Layout of drawing. Lines,
39
Civil Engineering Assistant
practice 15. Draw types of Lines, Lettering, Dimensioning.
dimensioning lettering and numbering (06 hrs)
Technique as per as per IS 962- 1989, SP-
BIS. (Mapped 46:2003. (05 hrs)
NOS: PCS/N9447) 16. Construction of plain
geometrical figures. (06
hrs)
Professional Construct plain 17. Construction of scales – Knowledge of different
Skill 20 Hrs; scale, Plain, comparative, types of scale. Principle of
comparative diagonal, vernier& scale R.F. (04 hrs)
Professional scale, diagonal of cords. (20 hrs)
Knowledge scale and vernier
04Hrs scale (Mapped
NOS: PCS/N9448)
Professional Draw Drawing of :- Different types of
Skill 22 Hrs; orthographic 18. Construction of solid projection views:
Professional projections of geometrical figures. (10 Orthographic, Isometric,
Knowledge different objects hrs) Oblique and Perspective.
10Hrs with proper lines 19. Three views in (10 hrs)
and Orthographic Projection
dimensioning. of Solid objects & section
(Mapped NOS: of solids. (12 hrs)
PCS/N9449)
Professional Draw Isometric, 20. Isometric, oblique and Theory of perspective view
Skill 28 Hrs; oblique and perspective views of (06 hrs)
perspective views geometrical solids,
Professional of different solid, hollow and cut sections.
Knowledge hollow and cut (28 hrs)
06 Hrs sections with
proper lines and
dimensions as per
standard
convension.
(Mapped NOS:
PCS/N9450)
Professional Draw component Drawing of :- Building materials:-
Skill 28 Hrs; parts of a single 21. Component parts of a Timber:- Types, Structure,
storied single storied residential disease & defects,
40
Civil Engineering Assistant
Professional residential building. (in sectional characterstic, seasoning,
Knowledge building with details) Showing preservation and uitility.
04 Hrs suitable symbols Foundation, Plinth, Alternaative material to
and scales. Doors, Windows, Brick Timber
(Mapped NOS: work, Roof, Lintel and Plywood, Block board,
PCS/N9451) Chajjah, Arches, etc. (28 Particle board, Fire proof
hrs) reinforced plastic (FRP),
Medium density fireboard
(MDF) etc.
Tar, bitumen, asphalt:-
Properties, application and
uses.(04 hrs)
Professional Create objects on 22. Function of keys and Computer aided drafting:-
Skill 114 CAD workspace practice of basic Operating system,
Hrs; using Toolbars, commands. (20 hrs) Hardware & software.
Commands, 23. Use of elementary Introduction of CAD.
Professional Menus, commands by CAD Its Graphical User
Knowledge formatting layer toolbar. (14 hrs) Interface.
04 Hrs and style. 24. Creation of objects in Method of Installation.
(Mapped NOS: different layers on CAD Basic commands of CAD.
PCS/N9452) workspace. (14 hrs) Knowledge of Tool icons
25. Plotting of drawing from and set of Toolbars.
CAD. (14 hrs) Knowledge of shortcut
26. 2D drafting of flash door, keyboard commands.
panel door, window, (04 hrs)
hand railing, wash basin,
sewerage pipe joints, etc.
(20 hrs)
27. Preparing Library folder
by creating blocks of the
above items. (12 hrs)
28. Stydy and prepare bar
bending schedule(20hrs)
Professional Identify different 28. Identify different types of Materials:-
Skill 28 Hrs; types of building bricks, uses and hollow Stones :– characteristics,
materials i.e. bricks. Standard size of types & uses.
Professional Stones, Bricks, bricks available at local Bricks :– Manufacturing,
Knowledge Lime, Pozzolanic, market. (04 hrs) characteristics of good
41
Civil Engineering Assistant
04 Hrs Cement, Sand, 29. Identify different types of bricks, types,uses and
Clay Products, stones, types and uses. hollow bricks.
Mortar their (04 hrs) Lime :– characteristics,
characteristic, 30. Identify different types of types, manufacturing & its
types, use & tiles, types and uses. (03 uses.
function. hrs) Pozzolanic :-
(Mapped NOS: 31. Identify different types of characteristics, types &
PCS/N9453) cement, types and uses, uses.
field test of cement. Etc. Cement :– Manufacturing,
(03 hrs) characteristics, types, uses
32. Identify different types of and test of good cement.
sand and aggregates,
types and uses. (03 hrs) Building materials:-
33. Identify different types of Sand:- characteristics,
lime, types and uses. (03 types & uses.
hrs) Clay Products :– types,
34. Identify different types of earthenware, stoneware,
steel, types and uses. (04 porcelain, terracotta,
hrs) glazing.
35. Identify different types of Mortar&Concrete:–
timber, earthen ware, Types,uses, preparation,
types and uses. (04 hrs) proportion, admixtures and
applications. (06 hrs)
Professional Mark different 36. Setting out a building: Building Construction:-
Skill 28 Hrs; types of Obtaining first, second, Foundation:-
Foundation and third & fourth lines, Purpose of foundation
Professional Set out marking diagonals, setting Causes of failure of
Knowledge Foundation out cross walls & offsets. foundation
10 Hrs trenches. (13 hrs) Bearing capacity of soils
(Mapped NOS: 37. Marking excavation lines Dead and live loads
PCS/N9454) & fixing of plinth & floor Examination of ground
levels. (05 hrs) Types of foundation –
38. Set out foundation (Spread Footing, Grillage
trench. (10 hrs) foundation, Pile
foundation, Raft
foundation, Well
foundation, Special
42
Civil Engineering Assistant
foundation)
Drawing of footing
foundation setting out of
building on ground
excavation
Simple machine
foundation. (10 hrs)
Professional Demonstrate 39. Demonstrate the use of Building Construction:-
Skill 12Hrs; different types of brick masonry tools. (02 Sequence of construction
brick masonry hrs) of a building.
Professional and Tools used in 40. Perform construction of Name of different parts of
Knowledge different bonds. wall header bond, building.
06 Hrs Perform stretcher bond, English Brick masonry:-
construction of bond, Flemish bond Terms, use and
wall - header (10hrs) classification..
bond, stretcher Strength of walls.
bond, English Strength of masonry.
bond, Flemish principles of construction
bond. (Mapped of bonds. Tools and
NOS: PCS/N9455) equipments used.(06 hrs)
Professional Perform different 41. Make scaffolding and Plastering : Types, thickness
Skill 24 Hrs; types of prepare surface for in different position,
Plastering & plastering. (04 hrs) materiels, tools used, defects
Professional Pointing, 42. Perform plastering and remedies, surface
Knowledge rendering & wall operation at different preparation for rendering &
06 Hrs cladding. surface - Plaster in two wall cladding.
(Mapped NOS: coats -External finishes— Special meterials used in
PCS/N9456) sand finish, textured plastering. Types of plaster
finish. (14 hrs) finishes.(06 hrs)
43. Perform rendering & wall
cladding. (06 hrs)
Professional Identify different 44. Perform application of Protective materials:-
Skill 24 Hrs; types of cement paint on different Paints:- characteristic,
Protective surfaces( 07hrs ) types, uses.
Professional materials i.e. 45. Perform application of Varnishes :–
Knowledge Paint, Varnish plastic emulsion on characteristics and
06 Hrs and their different surfaces(06 hrs) uses.(06 hrs)
43
Civil Engineering Assistant
application. 46. Perform application of
(Mapped NOS: enamel paint on different
PCS/N9457) surfaces(05 hrs)
47. Perform application
Process of varnishing on
different surfaces(06 hrs)
Professional Demonstrate 48. Perform Laying of D.P.C Treatments of building
Skill 20 Hrs; Damp Proof with proper methods and structures:-
Course in Materials. (20 hrs ) DPC Sources and effects
Professional different position. of dampness
Knowledge (Mapped NOS: Method of prevention of
06 Hrs PCS/N9458) dampness in building
Damp proofing materials
– properties, function and
types.(06 hrs)
Professional Prepare different Flooring practice:
Floors –Types of flooring.
Skill 28 Hrs; types of Flooring 49. Determination and
Flooring- materials used
(Mapped NOS: Formation of slope / level,
types.
Professional PCS/N9459) laying of Base Layers,
prepare method of
Knowledge laying of
laying, grinding &
06 Hrs Topping,application of
polishing of floor and
slurry for finishing, setting
prepare a survey report
out of skirting, formation
on materials used in
of spots for skirting. (18
flooring, site visit to
hrs)
check the practical
50. Use of screeds, formation
techniques of
of curve at the junction
flooring.(06 hrs)
of skirting & floor. (10 hrs)
Professional Perform site 51. Practice of folding & linear & Angular
Skill 38 Hrs; survey with unfolding of chain. (4 hrs) measurement by
Chain/Tape and 52. Ranging (direct/ indirect) instrument i.e. Chain, tape,
Professional prepare the site & distance measure with compass etc.
Knowledge Plan. (Mapped chain/ tape. (7 hrs) Introduction, , types of
06 Hrs NOS: 53. Offset taking & entering surveying, use, application
PCS/N9460) field book. (4 hrs) principal.
54. Chaining on sloping Main divisions (plane &
ground. (6 hrs) geodetic).
55. Conduct a chain survey of Uses of Chain/ tape, testing
44
Civil Engineering Assistant
a small area with all of a chain & correction.
details and plotting the Ranging (direct & indirect),
map. (9 hrs) Principle of chain survey,
56. Calculating the area of application. Terms used in
site. (3 hrs) chain survey,
57. Prepare a site plan by the types of offsets, limit of
help of chain / tape. (5 offset, field book, types of
hrs) field book, entry of field
book, method of chaining in
slopping ground.
Field procedure of chain
survey errors in chain survey,
plotting procedure.
Calculation of area (regular &
irregular figure)
Knowledge of site plan.
Knowledge of Mouza
Map.(06 hrs)
Professional Perform the site 58. Temporary adjustment of Surveying:-
Skill 15 Hrs; survey using prismatic compass. (03 Compass survey:-
Prismatic hrs) Basic terms used in
Professional Compass. 59. Measure fore & back compass survey.
Knowledge (Mapped NOS: bearing, R.B.,W.C.B. of a Instrument &its setting
06 Hrs PCS/N9461) line. (02hrs) up.
60. Measure true bearing of a Conversion of bearing
line. (02hrs) web to R.B.
61. Prepare a closed & open Calculation of included
traverse using prismatic angle from bearing local
compass measure the attraction, magnetic
bearings, entry into field declination and true
book, calculation of bearing, closing error.
correct bearing and Adjustment of closing
adjust. (Local attraction), error, precaution in using
determine the closing prismatic compass. (06
error and adjust. Plotting hrs)
the same. (08 hrs)
Professional Perform site 62. Demonstration of Plane table survey:-
Skill 14 Hrs; survey with Plane instrumentused for plane Plane table survey,
45
Civil Engineering Assistant
Table and table surveying & their principle, merits &
Professional prepare a map. uses (alidade, U-fork, demerits
Knowledge (Mapped NOS: trough compass) Set up Instrument used in plane
06 Hrs PCS/N9462) the plane table. (03 hrs) table survey setting up
Centering the plane table.
Levelling (centering, levelling,
Orientation orientation)
63. Practice the method of Methods of plane table
plane tabling (07 hrs) survey (radiation,
Radiation intersection, resection,
Intersection traversing)
Resection Error in plane table
Traversing survey.(06 hrs)
64. Determination of height
by telescopic alidade. (04
hrs)
Professional Prepare Levelling:- (53 hrs) Levelling:-
Skill 53 Hrs; topography map 65. Handling of levelling Auto level , dumpy Level,
by contours with instruments & their Tilting Level -
Professional levelling settings.(3) introduction, definition
Knowledge instruments. 66. Temporary adjustment of Principle of levelling.
06 Hrs (Mapped NOS: a level. Levelling staffs, its
PCS/N9463) 67. Simple levelling..(3) graduation & types.
68. Differential levelling (Fly Minimum equipment
levelling)..(3) required
69. Carry out Levelling field Types,component / part
book..(3) and function.
70. Equate Reduction of Temporary and
levels Height of permanent adjust ment,
collimation and Rise and procedure in setting up.
Fall method – Comparison Level& horizontal
of methods..(3) surface. Datum
71. Solve problems on Benchmark, Focussing&
reduction of levels .(3). parallax
72. Calculate Missing data Deduction of levels /
and fill up calculations Reduced Level.
&Arithmatical check in Types of levelling,
various problems and its
46
Civil Engineering Assistant
solution..(4) Application to chain and
73. Practice levelling with Levelling Instrument to
different instruments. .(3) Building construction.
74. Check levelling..(4) Contouring ;-Definition,
75. Profile levelling or Characteristics, Methods.
Longitudinal , plotting the Direct and Indirect
profile. .(4) methods
76. Surveying of a building Interpolation of Contour,
site with chain and Contour gradient , Uses
LevellingInstrument with of Contour plan and
a view to computing earth Map.
work..(4) Knowledge on road
77. Contour - Direct and project.(06 hrs)
Indirect methods..(3)
78. Make Topography map,
contours map..(3)
79. Solve trigonometric
problems..(3)
80. Prepare a road project in
a certain alignment..(4)
Professional Perform a site Theodolite survey:- (12hrs) Introduction and Types
Skill 12 Hrs; survey with 81. Field work of of Theodolite,
Theodolite and theodolite..(1) parts of Theodolite,
Professional prepare site plan. 82. Measure Horizontal angle. Terms used in Theodolite
Knowledge (Mapped NOS: Vertical angle, magnetic survey.
06 Hrs PCS/N9464) bearing of a line..(2) Temporary adjustment
83. Levelling with a of Theodolite,
theodolite..(2) Angle measurement
84. Calculation of area from process. Reading of
traverse..(2) angles, field book entry
85. Determination of of measured angles.
Heights..(2) Permanent adjustment
86. Calculation of departure, of Theodolite.(06 hrs)
latitude, northing and
easting.(2)
87. Setting out work-Building
work, etc. .(1)
Professional Perform a site 88. Application of survey Total Station:- –
47
Civil Engineering Assistant
Skill 14 Hrs; survey with Total using Total Station. (1 hrs) Introduction.
Station and 89. Field procedure for co components parts,
Professional prepare site plan. ordinate measurement. (1 accessories used.
Knowledge (Mapped NOS: hrs) characteristics, features.
06 Hrs PCS/N9465) 90. Field procedure to run advantages and
open traverse and closed disadvantages.
traverse. (2 hrs) principle of EMD.
91. Transfer or establish Working and need.
Bench Mark. (1 hrs) Setting and
92. Perform stakeout / measurement.
demarcation of building Electronic, display & Data
layout /plot layout/ reading.
roads/ alignment. (1 hrs)
Rectangular and polar co-
93. Measure remote distance ordinate system.
and elevation. (1 hrs)
Terminology of open and
94. Calculate surface area on
closed traverse.
field/site. (1 hrs)
(06 hrs)
95. Calculate volume of
field/site. (1 hrs)
96. Procedure for down load
and up load data. (1 hrs)
97. Simple survey map using
Auto CAD. (4 hrs)
Professional Identify timber 98. Identify different Common Indian timbers
Skill 26 Hrs; and perform wooden sample piece Defects in timber,
sawing and i.e.- soft wood & hard diseases of timber,
Professional planning using wood, wooden grains knots, shakes, grains etc.
Knowledge hand and power etc. & their applications carpentry hand tools,
06 Hrs tools. (Mapped Annual ring, knots, measuring tools and
NOS: MIN/ shakes &chicks etc.). uses.
N0454) (03hrs) work holding devices,
99. Demonstrate power tools, viz. saws,
application of hand drills, etc.
tools, measuring tools, Description of Carpentry
and work holding Joinery, Planing,
devices. (03 hrs) Moulding, Rebating,
100. Demonstrate use of Chamfering, Sawing,
different power tools, etc.(06 hrs)
48
Civil Engineering Assistant
viz. saws, drills, etc.
(03hrs)
101. Perform sawing,
planning,Moulding,
Rebating, Chamfering,
etc. using different
types of saws, and
plains. (14 hrs)
102. Sharpen and set
different type saw
bladeand planer blade/
cutter. (03hrs)
Professional Demonstratesurf 103. Planning face, face Type of different planes
Skill 20 Hrs; ace finish with edge, etc. (5hrs) and their proper uses in
exact sizing by 104. Demonstrate the use of wood work - Description,
Professional planning marking, mortise gauge function and its size,
Knowledge operation. etc. (3 hrs) setting, knowledge of
06 Hrs (Mapped NOS: 105. Test the accuracy of sharpening and uses etc.
MIN/ N0454) flatness and twist-ness knowledge of using
of the surface by using marking gauges.
try square. (4 hrs) Important instruments
106. Demonstrate the use of necessary for checking
winding strips, cross flatness and twistness of
planning, edge planning. surface
(4hrs) Sharpening and grinding
107. Demonstrate portable angle of cutter.
power planer machine Portable power planer -
and its function. (4 hrs) useful in modern wood
work and new
technology design. (06
hrs)
Professional Prepare different Prepare different wooden Description of different
Skill 28 Hrs; wooden Joints. joints by using different types joint.
(Range of skill - tools - Uses of joint :- Framing
Professional framing joint, 108. Make framing joint - joint angle joint and
Knowledge Housing joints, Mortise and tenon Joint lengthening joint, housing
08 Hrs broadening (Single and double, Plain joint, broadening joint
joints, hunched, Mitre corner) etc.
49
Civil Engineering Assistant
Lengthening (08hrs)
joints). (Mapped 109. Make Housing joints - Wood products
NOS: MIN/ Full housing, Bridle, - Industrial forms of
N0454) Stopped housing (04 timber
hrs) - Veneer
110. Make broadening joints - Laminated sheet
- Simple butt joint, - Fibre board
Riveted butt joint, etc. - Hard board
(08 hrs) - Plywood(08 hrs)
111. Lengthening joints:End
half lap joint, End over
lap joint, End bends lap
joint,slopping scarf,
racking scared, half
lapping scarf , table
scarf joint etc. (08 hrs)
Professional Make small Make small wall bracket – Calculation of timber
Skill 20 Hrs; wooden job as 112. Make joint on hard required for Wall Bracket
per drawing with wood to make small List out the sequence of
Professional schedule sizes of frame. (7 hrs) operation of the job
Knowledge timber or 113. Stopped Tenon & (06 hrs)
06 Hrs alternatives of Mortise joint on hard
timber i.e. FRP, wood in the frame to
MDF, FOAM using set the selves. (6 hrs)
various hardware. 114. Make selves by six
(Mapped NOS: pieces of hard wood
PCS/N9466) with single lapped half
lap dovetail joint with
frame (two nos. of
selves). (07hrs)
Professional Make different Making of :- Doors –Parts, Location,
Skill 28 Hrs; types of doors 115. Different Types doors standard sizes, types.
and windows including panelled, Windows-types.
Professional with fixing of glazed and flush door. Ventilators-purpose-types.
Knowledge component. (20 hrs) (06 hrs)
06 Hrs (Mapped NOS: 116. Different types windows
PCS/N9467) and ventilators. (08 hrs)
50
Civil Engineering Assistant
Professional Demonstrate 117. Prepare terminations of Electrical Wiring:-
Skill 28 Hrs; joining of cable ends (02 hrs) Safety precaution and
electrical wire 118. Practice on skinning, elementary first aid.
Professional and carry out twisting and crimping. Artificial respiration and
Knowledge soldering, (04 Hrs) treatment of electrical
04 Hrs crimping 119. Identify various types of shock
observing related cables and measure Elementary electricity
safety conductor size using and its units.
precautions. SWG and micrometer. General ideas of supply
(Mapped NOS: (02 Hrs) system.
MIN/N3102) 120. Make simple twist, Wireman’s tools kit.
married, Tee and Wiring materials.
western union joints. Electrical fittings.
(08 Hrs) System of wirings. Wiring
121. Make britannia straight, installation for domestic
britannia Tee and rat tail lightings.
joints. (08 Hrs) Conductor,
122. Practice in Soldering of insulator,semi conductor,
joints / lugs. (04 Hrs) cable joints,
measurement of cable
(04 hrs)
Professional Demonstrate 123. Demonstrate different Types of Fuses, MCB
Skill 28 Hrs; Electrical wiring electrical wiring system soldering, ELCB, RCCB,
with fixing of with fixing of different ABCB, MCCB AC and DC,
Professional accessories accessories. (03 hrs) AC fundamentals, poly
Knowledge conforming ISI 124. Make electrical Fuse phase
06 Hrs rules ( Range of joints, fixing MCB. (3 types of electrical wiring
skills - different hrs) Different Electrical
types of Electrical 125. Connect lamps with wiring accessories,
wiring, joining of switches. (06 hrs) ISI rules of wiring
Fuses,fixing of 126. Stair case circuit wiring. Illumination
MCB, connection (4 hrs) (06 hrs)
of lamp with 127. Godown wiring. (6 hrs)
switch and 128. Hospital wiring. (6 hrs).
different fitting,
etc.). (Mapped
NOS:
MIN/N3102)
51
Civil Engineering Assistant
Professional Demonstrate 129. Install earthing in Earthing, types of
Skill 28 Hrs; installation of different position. (10 earthing
electrical hrs) Earthing Pit.
Professional appliances, 130. Install and connect Different electrical
Knowledge Earthing and electrical appliances and appliance, accessories,
04 Hrs estimate costing take reading with Voltmeter.
of wiring. Voltmeter. (10 hrs) Estimation and costing of
(Mapped NOS: 131. Prapare materials list wiring.(02 hrs)
MIN/N3102, and costing of wiring.
MIN/N3104, (04 hrs)
MIN/N3102)
Professional Prepare a Simple 133. Perform Simple pipe Plumbing tools, meterials
Skill 18 Hrs; pipe connection connection using G.I. used in plumbing. (02 hrs)
demonstrating Pipes, socket, elbow,
Professional cutting, joining of tee, reducing elbow, G.I.Different types of pipes,
Knowledge pipe with union, cap fittings and Joints - GI,
plug,
10Hrs different method reducer, Three face PVC, AC,SW, CI, lead, steel
using different elbow, reducing socket, - Properties and use in
types of fittings. plumbing work(04 hrs)
plug, G.I. nipple etc. (18
(Mapped NOS: hrs) Method of cutting and joining
MIN/N3208) of pipes.
Drills - types and uses .
Tap and Dies - types and
uses, calculation of Tap drill
size.(04 hrs)
Professional Prepare layout of 134. Layout of soil pipe and Sanitary Technical terms
Skill 33 Hrs; soil pipe and waste pipe to the - sewer, sewage, sullage etc.
waste pipe with sanitary fitting using -Soil pipe and waste pipe
52
Civil Engineering Assistant
Professional different types of different types of fitting fitting
Knowledge sanitary fittings. viz. Door junction, door Different types of water
12 Hrs (Mapped NOS: Bend , H.R. bend, Plain closets Different types of
PCS/N9468) Bend, Double door urinal port Kitchen sinks,
junction, inverter Bath tub, Wash basin.
junction, cowel , floor (12 hrs)
trap, Gully trap, P-trap
etc. (7 hrs)
135. Fitting of I.W.C with
high level cistern. (06
hrs)
136. Fitting of washbasin (04
hrs)
137. Fitting of E.W.C. with
low level cistern. (04
hrs)
138. Fitting of kitchen sink.
(04 hrs)
139. Fitting of bath tub. (04
hrs)
140. Fitting of urinal pot with
auto cistern. (04 hrs)
Professional Prepare a water 141. Install water meter. (04 Water meter
Skill 28 Hrs; supply system in hrs) • Installation of water
residential 142. Remove air lock. (03 hrs) meter
Professional buildings using 143. Determination of pH by • Removal of air lock
Knowledge different types of pH meter. Analysis and Purification of water
14 Hrs valves, fittings treatment of Effluent Mineral matter,
and appliances. water. (05 hrs) Hardness, Causes of
(Mapped NOS: Scale formation &their
PCS/N9469) Removal. Water
Purification: Treatment
plants for different
groundwater
contaminants,
Treatment plants for
surface water.(07 hrs)
53
Civil Engineering Assistant
144. Recondition taps, valves Types of damages in taps ,
& flushing tank, test for valves , water meter and
correct functioning. (03 tanks - Method of
hrs) rectification
145. Prepare a water supply Water supply - Sources of
pipe line system in water
residential buildings Storage of water Distribution
using different types of of water Different types of
valves, fittings and valves used in Plumbing,
appliances. (05 hrs) Types of tanks R.C.C., P.V.C.
146. Prepare different Iron tanks etc.
objects on 3D Modelling (07 hrs)
Create objects on concept in CAD. (08 hrs)
3D Modelling
concept in CAD
(Mapped NOS:
PCS/N9470)
WORKSHOP CALCULATION & SCIENCE: (40 Hrs)
Professional Demonstrate WORKSHOP CALCULATION & SCIENCE:
Knowledge basic
Unit, Fractions
mathematical
WCS- 40 Hrs. Classification of unit system
concept and Fundamental and Derived units F.P.S, C.G.S, M.K.S and SI units
principles to Measurement units and conversion
perform practical Factors, HCF, LCM and problems
operations. Fractions - Addition, substraction, multiplication & division
Understand and Decimal fractions - Addition, subtraction, multilipication &
explain basic division
Solving problems by using calculator
science in the
Square root, Ratio and Proportions, Percentage
field of study. Square and suare root
(Mapped NOS: Simple problems using calculator
PCS/N9471) Applications of pythagoras theorem and related problems
Ratio and proportion
Ratio and proportion - Direct and indirect proportions
Percentage
Precentage - Changing percentage to decimal and fraction
Material Science
Types metals, types of ferrous and non ferrous metals
Physical and mechanical properties of metals
Introduction of iron and cast iron
54
Civil Engineering Assistant
Difference between iron & steel, alloy steel and carbon steel
Properties and timber
Mass, Weight, Volume and Density
Mass, volume, density, weight and specific gravity
Heat & Temperature and Pressure
Concept of heat and temperature, effects of heat, difference
between heat and temperature, boiling point & melting point
of different metals and non-metals
Scales of temperature, celsius, fahrenheit, kelvin and
conversion between scales oftemperature
Heat &Temperature - Temperature measuring instruments,
types of thermometer, pyrometer and transmission of heat -
Conduction, convection and radiation
Co-efficient of linear expansion and related problems with
assignments
Basic Electricity
Introduction and uses of electricity, molecule, atom, how
electricity is produced, electric current AC,DC their
comparison, voltage, resistance and their units
Conductor, insulator, types of connections - series and
parallel
Ohm's law, relation between V.I.R & related problems
Electrical power, energy and their units, calculation with
assignments
Electrical power, HP, energy and units of electrical energy
Mensuration
Area and perimeter of square, rectangle and parallelogram
Area and perimeter of Triangles
Area and perimeter of circle, semi-circle, circular ring, sector
of circle, hexagon and ellipse
Surface area and volume of solids - cube, cuboid, cylinder,
sphere and hollow cylinder
Finding the lateral surface area, total surface area and
capacity in litres of hexagonal, conical and cylindrical shaped
vessels
Trigonometry
Measurement of angles
Trigonometrical ratios
Trigonometrical tables
Application in calculating height and distance (Simple
applications
Project Work/ Industrial Visit
55
Civil Engineering Assistant
SECOND YEAR
Reference Professional Skills
Professional Knowledge
Duration Learning (Trade Practical)
(Trade Theory)
Outcome With Indicative Hours
Professional Demonstrate test 147. Test cement for Definitions and terms
Skill 38 Hrs; and analysis of consistency, setting related to concrete
cement, times & strength. (8 hrs) technology.
Professional aggregate, sand, 148. Conduct field tests for Applications of concrete
Knowledge effect of water adulteration. (04 hrs) technology and modern
16Hrs cement ratio. 149. Make proper trends
(Mapped NOS: arrangement to store CEMENT :
PCS/N9472) cement at site. (02 hrs) Types of cement, relevant IS
150. Perform sieve analysis on codes comparative study of
aggregate. (02 hrs) their physical & chemical
151. Determine grading, properties, significance of
fineness modulus. (02 different properties
hrs) • Hydration of cement
152. Determine presence of • Selection of cement
silt and clay. (02 hrs) • Storage of cement
153. Perform test to • Factors affecting strength of
determine shape & size cement
of aggregate. (04 hrs) • Rejection of cement
154. Perform test to AGGREGATE :
determine bulking of • Classification (IS : 383)
sand. (04 hrs) • Grading
155. Perform test and analyse • Characteristics (grading,
the effect of water fineness modules)
cement ratio (w/c) on • Bulking of fine aggregate
56
Civil Engineering Assistant
strength of cement. (10 • Deleterious substances
hrs) • Factors affecting strength of
concrete
WATER
• Quality
• Water requirement for
hydration & workability
• Effect of impurities
present in water
ADMIXTURE :
• Meaning of terms
• Functions
• Classification
• Water proofing and
permeability reducing
admixture
CONSTRUCTION CHEMICALS :
• Interpretation of
specifications manufactures
• Meaning of terms
• Functions
• Classification (IS : 4082)
• Water proofing and
permeability reducing
admixture(16 hrs)
Professional Prepare concrete, 156. Prepare concrete and lay Preparation of concrete
Skill 40 Hrs; carry out simple at required place using Methods used, merits and
form work and power tools. (10hrs) demerits of methods, tools and
Professional reinforcement 157. Carry out all operations equipment used and
Knowledge with the taking necessary precautions to be taken for the
10Hrs application of precautions related to following processes :
modern Power from work and • Batching
Tools. (Mapped reinforcement. (10 hrs) • Mixing
NOS: PCS/N9473) 158. Test strength of • Transportation
concrete. (10 hrs) • Placing
159. Remove form work • Compaction
Properly. (10 hrs) • Curing
• Finishing
57
Civil Engineering Assistant
• Strength & durability
requirements (IS : 456 -
2000)
• Stripping of form work
• Application of Modern Power
Tools(10 hrs)
Professional Prepare 160. Prepare reinforcement Classification &
Skill 98 Hrs; reinforcement of for foundation, beams, specifications of concrete
different R.C.C. columns, slabs, Retaining Classification of concrete
Professional members i.e. Wall etc. (80 hrs) according to grade, weight
Knowledge Foundation, 161. Basic modelingin stadd & methods of mixing
18 Hrs beams, columns, pro software.(18) Ready mixed concrete, self
slabs, Retaining levelling concrete,
Wall, etc. nominal mixed and design
(Mapped NOS: mixed concrete
PCS/N9474) introduction to stadd pro
software
Properties of concrete -
Workability &
consistency
Segregation
Bleeding
Strength
Durability
Impermeability
Volume stability
R.C.C. members for
foundation, beams,
columns, slabs, Retaining
Wall etc.(18 hrs)
Professional Erect scaffolding 162. Select appropriate Scaffolding & form work -
Skill 56Hrs; and make material for form work at Definitions of common
intricate form different locations. technical terms used in
Professional work at different (06hrs). Scaffolding, form work .
Knowledge locations . 163. Erect scaffolding & make Types & applications
18Hrs (Mapped NOS: form work at different Different materials used in
PCS/N9475) locations. (40hrs) form work.
164. Identify defects & rectify
58
Civil Engineering Assistant
form work. (10hrs) Methods and tools used for
form work.
Safety precautions to
be observed in
scaffoldingand form work
Defects in form work
Deshuttering /removal of
form work.
Maintenance & repair of
form work
Plain cement concrete
(PCC) & Reinforced cement
concrete (RCC)
Properties of PCC & RCC in
green state and hardened
state
Importance of form work
and reinforcement in
construction(18hrs)
Professional Prepare a bar 165. Prepare a bar bending Bar bending
Skill 64 Hrs; bending schedule schedule of different RCC Technical terms & their
and demonstrate members. (10 hrs) meanings, Symbols,
Professional bar bending and 166. Demonstrate different conventions used in bar
Knowledge calculate the operations in bar bending
24 Hrs estimated bending (straightening of Specifications of material
quantity of bars, cutting of bars, Physical properties of
materials. bending of bars, placing reinforcing bars
(Mapped NOS: of bars, binding of bars, Estimate the quantity of
PCS/N9476) fixing of cover blocks). material
(44 hrs) Structural elements &
167. Estimate quantity of characteristics (simply
steel and binding wire supported, continuous,
required for a given job fixed, cantilever, overhang)
(10 hrs) Importance of use of
reinforcement in concrete
Tools used in bar bending
Correct use of tools
59
Civil Engineering Assistant
Different operation in bar
bending (straightening of
bars, cutting of bars,
bending of bars, placing of
bars, binding of bars, fixing
of cover blocks)
Use of relevant BIS codes &
tables
Guidelines for laying
reinforcement.(24hrs)
Professional Make different 168. Making of shuttering & Arches: - Technical terms-.
Skill 40 Hrs; types of arches supports with uprights types ,centring
and lintels with and wedges for Arches, Lintel :-types,wooden, brick,
Professional chajja. (Mapped Lintels and Lintels with stone, steel & RCC.
Knowledge NOS: PCS/N9477) Chajjahs. (10 hrs) Chajjas – characteristics,
08 Hrs 169. Cutting, bending &Centring&Shuttering.(08 hrs)
placing of
reinforcement. (10hrs)
170. Mixing, placing &
compacting concrete.
(04 hrs)
171. Spanning of opening with
a
semi-circular arch,
making centering, cutting
of templates for
voussoirs& preparing
voussoirs, setting
uprights of arch. (08 hrs)
172. Construction of arch
&removing centering.(08
hrs)
Professional Lay out different Layout different forms of Stairs: Technical terms,
Skill 56Hrs; types of vertical vertical movements:- relation between tread &
movement 173. As per shape - straight, rise,
Professional according to open newel, dog- Types of stairs, construction
Knowledge shape, location, legged, geometrical and details of brick, stone & RCC
16Hrs materials by using bifurcated stairs & spiral stairs.
60
Civil Engineering Assistant
stair, lift, ramp stairs. (25 hrs) Spiral stairs with precast
and escalator. 174. As per material - brick, concrete steps.
(Mapped NOS: wooden, steel & RCC Basic concept of lift and
PCS/N9478) stairs. (25 hrs) Escalator.(16hrs)
175. Lay out of Lift and
Escalator (06hrs)
Professional Explain pile 176. On site practical Pile foundation
Skill 40 Hrs; foundation. trainingof piling (Visit to • uses of piles
(Mapped NOS: new construction site at • types of piles
Professional PCS/N9479) the time piling work or • materials used in the
Knowledge Demonstration through construction of load bearing
16 Hrs related video) (40 hrs) piles
Factors considered in
selection of piles
Pile driving & equipments
used for pile driving(16 hrs)
Professional Prepare a Single 177. Prepare a Single Storied Introduction about
Skill 84 Hrs; Storied Residential Building Plan building construction
Residential as per local by law Types of buildings
Professional Building Plan as including all details Plan, Structural system of
Knowledge per local by law Elevation, Section building.
24 Hrs using CAD. through Staircase and Different parts of building
(Mapped NOS: Toilet & Kitchen, Terrace Site selection
PCS/N9480) Plan, Structural Plan and Orientation and
other details i.e. Sanitary ventilation of building
& Electrical items with (24 hrs)
proper symbols by using
CAD. (84 hrs)
Professional Demonstrate 178. Prepare simple drawing Building plans - Introduction,
Skill 28 Hrs; ArchiCAD and 3D with ArchiCAD and 3D Types of plan- Typical floor
Max for Solid Max for Solid Modelling plan, Foundation plan,
Professional Modelling of of Architectural / Civil Structural plan, Terrace plan.(08
Knowledge Architectural / 3D archi CAD 3D model hrs)
08 Hrs Civil 3D Drawing. software (28 hrs)
(Mapped NOS:
PCS/N9481)
Professional Prepare Solid 179. Prepare 3D model using Main considerations of
Skill 28 Hrs; Modelling of 3d Max software (08 architectural design
61
Civil Engineering Assistant
Architectural Hrs) Bye-law of the locality
Professional /Civil 3D Drawing 180. Create 3D model from Climate and its effects
Knowledge using 3d Max and 2D plane (08 Hrs) Materials and method of
08 Hrs Revit software. 181. Lighting and rendering its construction.
(Mapped NOS: (04 Hrs) People and their
PCS/N9482) 182. Material editor using requirements.
BIM software like (08 hrs)
Revit(04 Hrs)
183. Quantity calculation of
materials archi CAD 3D
model software (04 Hrs)
Professional Work out rate 184. Prepare rate analysis of Steps in rate analysis
Skill 18 Hrs; analysis of different item of works Material
different item of including material, Labour
Professional works with labour, Plant machinery, Plant and machinery
Knowledge detailed over head charge, Profit Overhead charges
08 Hrs Specification. with the details Profit
(Mapped NOS: specification. (10 hrs) Specification
PCS/N9483) 185. Calculation of floor area General and detailed
and carpet area. (04 hrs) specification(08 hrs)
186. Calculation of FAR. (04
hrs)
Professional Prepare a detail 187. Estimate of one room Estimating and costing
Skill 56 Hrs; estimate of one building by center line Need and importance
room building by method and separate Types of estimate
Professional centre line wall method. (30 hrs) Items of work
Knowledge method and 188. Calculation of different Measurement of items
16 Hrs separate wall material from the Calculation of quantities of
method,calculate quantities worked out in various items
the quantities of the estimate.(26 hrs) (16hrs)
materials
involved from the
above estimated
quantities&
prepare a
abstract of cost
for the above
item of works.
62
Civil Engineering Assistant
(Mapped NOS:
PCS/N9484)
Professional Perform repair 189. Perform repairing of Repair Plastering, white
Skill 24 Hrs; Plastering, white plaster and different washing, painting flooring,
washing, painting items of works. (08 hrs) replacing of glass,
Professional flooring, replacing 190. Use of Water proofing repolishing of floor, stain
Knowledge of glass, compound, Admixture. removal from floor,
08 Hrs repolishing of (6 hrs) wooden works.(08 hrs)
floor, stain 191. Perform white washing,
removal from floor polishing,stain
floor, wooden removal form floor,
works. (Mapped wooden works. (10 hrs)
NOS: PCS/N9485)
Professional Perform field 192. Field Training to Special repair
Skill 12 Hrs; training of Strengthening of • Foundation failure
Foundation foundation (03 hrs) • Strengthening of
Professional failure, 193. Rectification of leaking foundation
Knowledge Strengthening of roof.(5 hrs) • Rectification of leaking
08 Hrs foundation, 194. Repair of expansion roof
Rectification of joint. (4 hrs) • Repair to expansion
leaking roof, joint(08 hrs)
repair of
expansion joint.
(Mapped NOS:
PCS/N9486)
Professional Demonstrate anti 195. Market survey for Anti-termite treatment –
Skill 12 Hrs; - termite different materials used objectives, materials, uses and
treatment and for anti termite applications.
Professional Market survey for treatment (03hrs) • Pre construction treatment
Knowledge different 196. Pre construction Anti - • Post construction treatment
08 Hrs materials used in termite treatment(4 hrs) Weathering course –
anti termite 197. Post construction Anti - objectives and materials
treatment. termite treatment (05 required.(08 hrs)
(Mapped NOS: hrs)
PCS/N9487)
63
Civil Engineering Assistant
Professional drainage plan, plumbing lines and drainage plan
Knowledge repairing of sanitary fittings. (24 hrs) •Tracing leakage, repair to
12 Hrs service main, service main, repairing of
waist outlet waste outlet
cleaning of •Cleaning of sanitary
sanitary installation
installation, •Scrapping and painting of
scrapping and pipes(12hrs)
painting of pipes
of a new site.
(Mapped NOS:
PCS/N9488)
Professional Demonstrate use 199. Field Training about use Adhesive and joint filler
Skill 18 Hrs; of Adhesive in of Adhesive in imber,tile •Introduction
timber,tile fixing, fixing, jointing in •Types
Professional jointing in concrete,joint filler & •Adhesive used in timber
Knowledge concrete,joint sealing compound. (18 construction
08 Hrs filler & sealing hrs) •Adhesives used in ceramic tile
compound. fixing
(Mapped NOS: •Adhesives used in joining
PCS/N9489) concrete
•Joint filler
•Sealing compound(08hrs)
Professional Demonstrate 200. Field Training(56hrs) Construction equipments
Skill 56 Hrs; different types of •Classification
construction •Selection of equipments
Professional equipments in •Sources of equipments
Knowledge Excavation, Excavation equipment
12 Hrs Hoisting, •Tractor
Conveying, •Bull dozer
Drilling. (Mapped •Excavator
NOS: PCS/N9490) Hoisting equipment
•Crane
•Pulley
•Cable way
Conveying equipments
•Belt conveyor
•Rope way
64
Civil Engineering Assistant
•Pumping equipments
Drilling equipments
•Types of drills
•Classification of drill
•Drill bits
Selection of drilling pattern(12
hrs)
Professional Demonstrate 201. Visit site and training Construction management.
Skill 48 Hrs; Construction about site supervision. Management of manpower,
Professional Management i.e. (20 hrs) materials,machines with
Knowledge manpower, 202. work to assist a civil economy.(16 hrs)
16 Hrs materials, engineer and perform as
machines and trainee Site Supervisor.
economy. (28 hrs)
(Mapped NOS:
PCS/N9491)
WORKSHOP CALCULATION & SCIENCE: (38 Hrs)
Professional Demonstrate WORKSHOP CALCULATION & SCIENCE:
Knowledge basic
Centre of Gravity
mathematical
WCS- 38 Hrs. Centre of gravity - Centre of gravity and its practical application
concept and Area of cut out regular surfaces and area of irregular surfaces
principles to Area of cut out regular surfaces - circle, segment and sector of
perform practical circle
operations. Related problems of area of cut out regular surfaces - circle,
Understand and segment and sector of circle
explain basic Area of irregular surfaces and application related to shop
problems
science in the
Algebra
field of study. Algebra - Addition , subtraction, multiplication & division
(Mapped NOS: Algebra - Theory of indices, algebraic formula, related problems
PCS/N9492) Elasticity
Elasticity - Elastic, plastic materials, stress, strain and their units
and young’s modulus
Elasticity - Ultimate stress and working stress
Profit and Loss
Profit and loss - Simple problems on profit & loss
Profit and loss - Simple and compound interest
Estimation and Costing
Estimation and costing - Simple estimation of the requirement
of material etc., as applicable to the trade
65
Civil Engineering Assistant
Estimation and costing - Problems on estimation and costing
Project Work/Industrial Visit
66
Civil Engineering Assistant
Learning outcomes, assessment criteria, syllabus and Tool List of Core Skills subjects which is
common for a group of trades, provided separately in www.bharatskills.gov.in /dgt.gov.in
67
Civil Engineering Assistant
ANNEXURE-I
68
Civil Engineering Assistant
trade related software.
17. Notebook PC 2 Nos.
18. Drafting Software like AutoCAD, or equiv. 24 Nos.
19. Plotter A0 size 1 No.
20. Laser Jet color printer A4 size As Required
21. Inkjet/ Laser Jet Printer A3 size 1 No.
22. Color Scanner/printer with Latest 1 No.
Configuration
23. Offline UPS As required
24. Computer work station module type 24 Nos.
25. Printer Table module type 1 No.
26. Operator’s chair 25 Nos.
27. Instructor ‘s Lab table 1 No.
28. Instructor’s chair with arm 3 Nos.
29. Book shelf with glass shutters 1 No.
30. Air conditioner As per
requirement
31. LAN connectivity As per
requirement
32. Internet connection 1 No.
33. Visualizer 1 No.
34. Vacuum Cleaner 1 No.
C. AUDIO VISUAL AIDS
35. LCD Projector 1 No.
36. Interactive Board 1 No.
D. EQUIPMENTS FOR PRACTICAL LABS
37. Box drawing instrument one 15 cm 5 nos.
compass with pin point, pin point &
lengthening bar, one pair spring bows,
rotating compass with interchangeable ink
and pencil points, drawing pens with plain
point & cross point, screw driver and box
of leads.
38. Protractor celluloid 15 cm semi-circular. 5 nos.
39. Scale card board-metric set of eight A to H in a box 1:1, 1:2, 1:2: 24 Nos.
5, 1:5, 1:10, 1:20, 1:50,
1:100, 1:200, 1:500,
69
Civil Engineering Assistant
1:1000, 1:2000, 1:1250,
1:6000, 1:38 1/3, 1:66 2/3.
70
Civil Engineering Assistant
60. Steel tape 5m & 2.5 m. 1 no.
61. Gunter’s chain 1 no.
62. Engineer’s chain 1 no.
63. Dumpy level builder 25 cm focal length x 23 mm 2 nos.
completes with box and
accessories and stand.
64. Levelling staff 4 meters reading to 5mm 2 nos.
telescopic type.
65. Surveyor’s umbrella. 4 nos.
66. Spade 2 nos.
67. Pickaxe. 2 nos.
68. Gloves (canvas and plastic) 24 Pair each
69. Gum boots 24 Pair
70. Chains 3 sets
71. Prismatic compass with stand and all 3 sets
accessaries
72. Plane tables 3 sets
73. Auto level latest model with all 3 sets
accessaries
74. Theodolites latest model with all 3 sets
accessaries
75. Total station latest model with all 2 sets
accessaries
F. CARPENTRY LAB
76. Flexible tape role steel 3 meter 24 Nos.
77. Try Square 20 mm 24 Nos.
78. Square bevel 24 Nos.
79. Marking Gauge Wooden 24 Nos.
80. Hand Saw 450 mm 24 Nos.
81. Saw tenon 300 mm 24 Nos.
82. Jack plane metal 335 mm X 50 mm cutter 24 Nos.
83. Plane smoothing metal 250 mm X 50 mm cutter 24 Nos.
84. Chisel firmer (bevel edge) 6, 10, 15, 20, 25mm with (5 24 Nos.
nos.)
85. Chisel mort ice 6,10,15, 24 Nos.
86. Screw driver 300 mm 24 Nos.
87. Wooden mallet medium size 24 Nos.
71
Civil Engineering Assistant
88. Hammer claw 500gms 24 Nos.
89. Carborandom stone 200x 50x 25mm 24 Nos.
90. Hand brush for bench cleaning 400mm 24 Nos.
91. Screw Driver 250 mm 24 Nos.
92. Pincer 50mm 5 No.
93. File Half Round 2nd Cut 250mm 12 Nos.
94. File half wood rasp bastard 300mm 12 Nos.
95. File slim taper 100 mm 12 Nos.
96. Card File (Steel) wire brush for file 12 Nos.
97. Electrically operated motorized cutter 5
Nos.
98. Boring tools 1 set
99. Fastenings 1 set
100. Hinges and locks 1 set each
G. PLUMBING LAB
101. Steel Rule 300 mm both in inch and 25 Nos.
mm
102. Hacksaw frame adjustable 250 to 300 mm 25 Nos.
103. Chisel cold flat 20 x 250 mm 25 Nos.
104. Hammer ball peen 800 gms. 25 Nos.
105. File flat rough 300 mm 25 Nos.
106. Level spirit wooden 300 mm 25 Nos.
107. Plumb bob 50 gms. 25 Nos.
108. Stilson wrench 200 & 350 mm 25 Nos.
109. Wooden mallet small 25 Nos.
110. Cutting pliers 25 Nos.
111. Chisel cold flat 20 mm x 300 mm 2 Nos.
112. Tap and die set to cut BSP Thread 1 set.
113. Spanner monkey up to 50 mm 2 Nos.
114. Cutter, pipe wheel type 6 mm to 25 mm. 1 No.
115. Inside caliper 150 mm 5 Nos.
116. Caliper outside 15o mm 5 Nos.
117. Plumbers ladle 2 Nos.
118. Plumbers metal melting pot 10 kg. 1 No.
119. Pipe vice to grip pipes up to 77 mm. 2 Nos.
120. Tool caulking set of 2 2 Sets
121. Stillson pattern pipe wrenches 450 mm to take pipe up to 2 sets
72
Civil Engineering Assistant
52 mm dia.
122. Stillson pattern pipe wrenches 300 mm to take pipe to 20 2 sets
mm to 32 mm.
123. Chain pipe wrenches 90 mm-650 mm 2 sets
124. Flat Smithy tong. 2 Nos.
125. Working Bench 24oox 1200 x 750 mm 2 Nos.
126. Ratchet rack with post and clamp flat 5 1 Set
drill 6 to 35 mm by 0.2 mm.
127. Ratchet pipe die 15 mm to 32 mm 2 No.
128. Double face hammers 5 Nos.
129. Monkey Plier (gas pliers) 5 Nos.
130. Electric handling machine 6 to 35 mm by 0.2 mm. for 1 No.
drilling
131. Trowel 125 2 Nos.
132. Saw plumber 300 mm 2 Nos.
H. ELECTRICAL LAB
133. Rule wooden 4 fold 60 mm 24 Nos.
134. Scriber 150 mm (Knurled Centre 24 Nos.
position)
135. Pincer 150 mm 24 Nos.
136. Plier insulated 150 mm 24 Nos.
137. Screw driver 150 mm 24 Nos.
138. Punch Centre 150 mmx 9 mm 24 Nos.
139. Knife double bladed electrician 24 Nos.
140. Hammer, cross pane 115 grams with handle 24 Nos.
141. Electrician connector, screw driver 100 mm. Insulated handle 24 Nos.
thin stem
142. Electrician testing pencil I I neon Tester 24 Nos.
143. Heavy duty screw driver 200 mm 24 Nos.
144. Electrician screw driver 250 mm thin stem 24 Nos.
insulated handle
145. Saw tenon 250 mm 24 Nos.
146. Hammer ball pane 0.75 kg with handle 24 Nos.
147. Firmer chisel wood 12 mm 24 Nos.
148. Gimlet 6 mm 24 Nos.
149. Bradawl 24 Nos.
150. Plier sued cutting 150 mm 24 Nos.
73
Civil Engineering Assistant
151. C. Clamps 200 mm, 150 mm, 100 mm 2 Nos.
152. Spanner 150 mm adjustable 15 2 Nos.
degree as cly-burns
153. Blow lamp 0.5 liter 2 Nos.
154. Melting pot 1 No.
155. Ladder 2 Nos.
156. Chisel cold flat 12 mmx 200 mm 2 Nos.
157. Chisel firmer 25 mm and 6 mm 4 Nos.
158. Drill machine hand 0 to 6 mm capacity 2 Nos.
159. Electric drill machine 12 mm capacity 1 No.
160. Out side micrometer 0 to 25 mm 1 No.
161. Bench grinder motorized 1 No.
162. Raw plug tool and bit 2 Nos.
163. Bearing puller 1 No.
164. Multi meter 0 to 1000 M ohms 2.5 to 2 Nos.
5000 volt
165. K.W. meter. 0 to 1 K.W. capacity with 1 No.
C.T.1: 2
166. Milli voltmeter Centre zero 100-0-100m volt. 1 No.
167. Spring balance 0 to 15 kg. And 0 to 2.5 kg. 2 Nos.
168. Screw driver 100 mm 5 Nos.
169. Square try 150mm blade 5 Nos.
170. Divider 150 mm, out side and 4 Nos.
inside caliper
171. Tweezers 100 mm. 5 Nos.
172. Snip straight 150 mm 2 Nos.
173. File flat 200 mm 2nd cut 3 Nos.
174. File half round 200 mm 2nd cut 5 Nos.
175. File half round 200 mm smooth 5 Nos.
176. File round 200 mm 2nd cut 5 Nos.
177. File flat 250 mm rough 5 Nos.
178. File flat 250 mm bastard 5 Nos.
179. Rasp, half round 200 bastard 5 Nos.
180. Iron, soldering 225 grams 125 watt with 5 Nos.
bits
181. Vice hand 50mm jaw 5 Nos.
182. Megger 500 volts 1 No.
74
Civil Engineering Assistant
183. Fan A.C. 230 volt 1200 mm 2 Nos.
184. Fan D.C. 220 volt 1200 mm 2 Nos.
185. Bench working 2.5x 1.20x 0.75 meters 5 Nos.
186. Almirah 2.5x1.20x0.50 meter 1 No.
187. Metal rack 180x150x47 cm. 5 Nos.
188. Wire stripper 20 cm. 1 No.
189. Domestic appliances: 1500 watt. 220v with 2 Nos.
(a) Electric hot plate temperature control.
(b) Electric kettle, 1000 watts, 230v 2 Nos.
(c) Electric iron 1200 watts, 230v with 2 Nos.
temperature control.
(d) Immersion heater 750/1000/1500w-230v 2 Nos.
(e) Geyser 25 liter 240v (storage type) 2 Nos.
(f) B.A. taps and dies 0-2-4-6-8 sizes 2 Nos.
(g) Mixture grinder 2 Nos.
190. Spring balance 0 –1 kg. 1 No.
191. Motor A.C. series type 230 v, 50 cycles, ¼ HP with 1 No.
starter and switch
192. Multi meter digital 12 Nos.
193. Motor AC single phase 230 volt, 50 cycles 1 No.
capacitor type with starter
switch 1HP
194. Motor universal 230 volt, 50 cycles with 1 No.
starter/switch 1 HP
195. Variable auto transformer 0-250 V, amps 2 Nos.
196. Earth leakage ckt. Breaker 1 no.
197. M.C.B. 5 KVA 1 no.
198. Voltage stabilizer manual and automatic 1 no.
Each
199. Multi meter 3 sets
200. Meger 2 sets
201. Earth tester 2 sets
202. Electric tool kit 4 sets
203. Multi meter 3 sets
FOR BUILDING CONSTRUCTION LAB
204. Measuring tape 15 mtr. (steel) 4 nos.
205. Land measuring steel tape 30 mt long 12 Nos.
75
Civil Engineering Assistant
206. Land measuring plastic tape 30 mt long 12 Nos.
207. Steel tapes 3 mt long 24 Nos.
208. Steel tapes 5 mt long 24 Nos.
209. Try square 4 Nos.
210. Marking point 4 Nos.
211. Tenon saw, dovetail saw 4 each
212. Chiesel different suitable sizes 4 sets
213. Hammer 500 gm. 4 Nos.
214. Hammer 1 kg. 4 Nos.
215. Hammer 5 kg. 4 Nos.
216. Bar bending table 4 Nos.
217. Bending pipes (suitable diameter and 2 each
length)
218. Bar bending lever (suitable diameter and 2 sets
length)
219. Manual bar bending machine of suitable 2 Nos.
size
220. Portable hand bender of suitable size 2 Nos.
221. Power cutter of suitable size 2 Nos.
222. Safety gloves 8 pairs
223. Safety glass 8 pairs
224. Shovel 5 Nos.
225. M.S pan 45 cm dia. 12 Nos.
226. Farma of mild steel for measuring Heaving volume 0.03472 2 No.
aggregate cm
227. Bucket G.i. 35 cm dia. 5 No.
228. Mason plumb rule with spirit level 24 Nos.
229. Mason square 30x60 cm 24 Nos.
230. Sieve for sand in adjustable stand 1mm, 100cm x 60cm fixed 2 No.
in steel frame
231. Trowel 25 cmx10cm 16 Nos.
232. Brick hammer with handle 12 Nos.
233. pointing Trowel 6” 24 Nos.
234. Line pin corner block 24 Nos.
235. Mortar board 2 mtx2 mt. 2 No.
236. Wire brushes 12 Nos.
237. Float wooden 24 Nos.
76
Civil Engineering Assistant
238. Steel float 24 Nos.
239. Sprit level 30 cm long 12 Nos.
240. Bolster 12 Nos.
241. Spade 12 Nos.
242. Ladder aluminium 3m long 3 Nos.
243. Pick axe 5 Nos.
244. Hammer 250 grams 12 Nos.
245. Crow bar 30mm dia 1.5 m long of 6 Nos.
mild steel
246. Gloves canvas 12 Pair
247. Gloves plastic 12 Pair
248. Drums 200 liters capacity 2 Nos.
249. Brush for painting & white washing As required
250. Marking rope & thread 15 m 64 each
251. Bevel 8 Nos.
252. Pan (M.S. or PVC) 16 Nos.
253. Mortar board 2000 x 2000 2 Nos.
254. Measuring box 35 ltr. Capacity 4 Nos.
255. Plumb rule and Bob 8 Nos.
256. Straight edge 8 Nos.
257. Water tube 6m 8 Nos.
258. Bucket 5 ltr. & 10 lrt. 8 each
259. Concrete mixer 2 Nos.
260. Concrete vibrator pin type & plate type 2 each
261. Water drum 200 ltr. 4 Nos.
262. Mono block pump set 1/2 HP 4 Nos.
263. Steel / plywood shuttering plates 50 sqm.
264. Telescopic pipes / props 100 Nos.
265. Telescopic/ adjustable spans 25 Nos.
266. Masonry grinder 2 Nos.
267. Scientific calculator 16 Nos.
268. Weighing balance 1 kg., 10 kg. Digital 2 each
269. Bristle brush 25 & 40 mm with 250 2 each
handle
270. Vicat apparatus with plunger, needles and 2 set
mould
271. Stop watch 8 Nos.
77
Civil Engineering Assistant
272. Gauging trowel 4 Nos.
273. Digital compression testing machine 1 No.
274. Cube mould 150 mm size 24 No.
275. Cube mould 70.5mm size 10 Nos.
276. Measuring cylinder 100 ml., 500 m., 1000 ml. 4 each
277. Non porous plate 16 Nos.
278. Water container 1000 ltr. 1 No.
279. Vibrating machine 12000 ± 400 rpm 2 set
280. Graduated cylinder 8 Nos.
281. Metal tray 8 Nos.
282. Beaker 8 Nos.
283. Oven 1 No.
284. Weighing plateform digital 100 kg. 1 No.
285. Slump test apparatus with temping rod 2 set
286. Electronic balance 30kg – 1gram L.C 1 No.
287. IS Brass sieves - 4.75mm,2.36mm, 1.18mm, 1 each
600micron, 300 micron,
150 micron, 90 micron, 75
micron, 45micron, pan and
cover
288. Motorised sieve shaker 1 No.
289. Thickness and length gauges (Elongation 1 each
and Flakiness Index)
290. Pyconometer for specific gravity 2 Nos.
291. Bulk density apparatus (Cylindrical 1 No.
measure for fine aggregate and coarse
aggregate )
292. Aggregate impact tester with cylindrical 1 No.
cup and measuring cylinder
293. Sample tray- steel and plastic 300x250x40mm 12 Nos. each
294. Mortar cube vibrator 12000±400rpm 1 No.
295. Standard IS sand Grade 1, Grade 2, Grade 3 2 bagseach
296. Water testing kit – for ph value 2 Nos.
297. Electric heater 1 No.
298. Le Chatelier Mould (for soundness test of 1 No.
cement)
299. Le Chateliers flask (For specific gravity test 1 No.
78
Civil Engineering Assistant
of cement)
300. Slump Cone 1 No.
301. Marking rope & thread 15 m 64 each
302. Pan M.S. or PVC 16 Nos.
303. Sampling scoops 2kg and 5 kg 3 Nos.each
304. Drill and bit set 3 Nos.each
305. Spray painting machine 1 No.
306. Brushes for painting 12 Nos. each
307. Floor polishing machine 1 No.
308. Spanner monkey up to 50 mm 1 12 Nos.
309. Stillson pattern pipe wrenches 450 mm to take pipe up to 2 Nos.
52 mm dia.
310. Adjustable spanner A 375 12 Nos.
311. Double face hammers 12 Nos.
312. Screw driver Set 12 Nos.
313. Floats wooden 8 Nos.
314. Wire brushes 8 Nos.
315. Ladder 3m 8 Nos.
316. Aluminum float 8 Nos.
317. Tile cutter hand operated 4 Nos.
318. Power operated cutting machine 4 Nos.
319. Wooden mallet 8 Nos.
320. Polishing machine 1 No.
321. Polishing stone different grade / number 8 set
322. Bending pipes suitable dia& length 2each
Note: -
1. All the tools and equipment are to be procured as per BIS specification.
79
Civil Engineering Assistant
ABBREVIATIONS
80
Civil Engineering Assistant
81