Screenshot 2024-02-24 at 8.55.27 AM
Screenshot 2024-02-24 at 8.55.27 AM
Basic Documentation
Edition 4.1
CE1P3181en
2016-04-14 Building Technologies
Contents
1 About this document....................................................................................4
1.1 Revision history ..............................................................................................4
1.2 Reference documents.....................................................................................4
1.3 Before you start ..............................................................................................5
1.3.1 Copyright .....................................................................................................5
1.3.2 Quality assurance .......................................................................................5
1.3.3 Document use/request to the reader ..........................................................5
2 Summary .......................................................................................................6
2.1 Brief description ..............................................................................................6
2.2 Types and features .........................................................................................7
2.3 Equipment combinations ................................................................................8
2.4 Accessories ....................................................................................................9
2.5 Ordering ..........................................................................................................9
3 Use .............................................................................................................. 10
4 Functions.....................................................................................................11
4.1 Temperature control......................................................................................11
4.2 Operating modes ......................................................................................... 12
4.3 Room temperature setpoints ....................................................................... 13
4.4 Setpoints and sequences ............................................................................ 14
4.4.1 2-pipe and 2-stage applications ............................................................... 14
4.4.2 4-pipe applications ................................................................................... 15
4.5 Applications overview .................................................................................. 16
4.5.1 Applications for fan coil systems.............................................................. 16
4.5.2 Applications for Universal systems .......................................................... 17
4.5.3 Applications for heat pump systems (RDG110.., RDG160T..) ................. 18
4.6 Additional features ....................................................................................... 19
4.6.1 Qx- relay switching functions (RDG160T.. only) ...................................... 24
4.7 Control sequences....................................................................................... 25
4.7.1 Sequences overview (setting via parameter P01) ................................... 25
4.7.2 Control outputs configuration (setting via DIP switches 4/5 and
parameters) ............................................................................................................ 26
4.7.3 2-pipe fan coil unit .................................................................................... 27
4.7.4 2-pipe fan coil unit with electric heater..................................................... 28
4.7.5 2-pipe fan coil unit with radiator or floor heating ...................................... 30
4.7.6 4-pipe fan coil unit .................................................................................... 31
4.7.7 4-pipe fan coil unit with electric heater (RDG100..) ................................. 33
4.7.8 2-stage heating or cooling........................................................................ 35
4.7.9 Chilled/heated ceiling and radiator applications ...................................... 37
4.7.10 Compressor applications (general) .......................................................... 37
4.7.11 1-stage heating or cooling with reversing valve (RDG110..).................... 38
4.8 Control outputs ............................................................................................ 39
4.9 Fan control ................................................................................................... 42
4.10 Multifunctional input, digital input ............................................................. 47
4.11 Auto timer (RDG100T, RDG100T/H, RDG160T.. only)............................... 48
4.12 Handling faults ......................................................................................... 51
4.13 Infrared remote control............................................................................. 51
4.14 DIP switches............................................................................................. 51
4.15 Control parameters .................................................................................. 52
4.15.1 Parameters of the "Service level" – Degree Celsius................................ 53
4.15.2 Parameters of the "Expert level with diagnostics and test" – Degree
Celsius 54
2/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies Contents 2016-04-14
4.15.3 Parameters of the "Service level" – Degree Fahrenheit ...........................56
4.15.4 Parameters of the "Expert level with diagnostics and test" – Degree
Fahrenheit ...............................................................................................................57
4.15.5 Diagnostics and tests ................................................................................59
5 Handling ......................................................................................................60
5.1 Mounting and installation..............................................................................60
5.2 Operation ......................................................................................................62
5.3 Disposal ........................................................................................................64
6 Engineering .................................................................................................65
6.1 Connection terminals ....................................................................................65
6.2 Connection diagrams....................................................................................66
7 Mechanical design......................................................................................71
7.1 General .........................................................................................................71
7.2 Dimensions ...................................................................................................72
8 Technical data .............................................................................................73
3/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies Contents 2016-04-14
1 About this document
1.1 Revision history
Edition Date Changes Section Pages
4.1 June 2015 Add inch dimensions All
Add degree Fahrenheit information for RDG110U and RDG160TU
4.0 Feb 2015 Add new variants RDG110U and RDG160TU and other corrections All
3.0 April 2014 Protection via circuit breaker 5.1, 6.2, 8
Combination control outputs with relay function All
New product RDG160T
Removed RDG140, RDG160
Doc valid for RDG100.. SW > = V7.2
Removed remarks for RDG100 SW < V7.2 (info in Doc V2.0)
RoHS-II adaptations
Several corrections
2.0 Dec 2011 Amendments concerning RDG100T/H All
Adaptive temperature adaption (electric heater) 4.8, 4.15
Function specifications for units with SW < V7.2
1.1 June 2009 Several small corrections All
1.0 May 2009 First edition
4/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
1.3 Before you start
1.3.1 Copyright
This document may be duplicated and distributed only with the express permission of
Siemens, and may be passed only to authorized persons or companies with the
required technical knowledge.
Before using our products, it is important that you read the documents supplied with or
ordered at the same time as the products (equipment, applications, tools, etc.)
carefully and in full.
We assume that persons using our products and documents are authorized and
trained appropriately and have the technical knowledge required to use our products
as intended.
More information on the products and applications is available:
On the intranet (Siemens employees only) at
https://workspace.sbt.siemens.com/content/00001123/default.aspx
From the Siemens branch office near you www.buildingtechnologies.siemens.com
or from your system supplier
From the support team at headquarters [email protected] if
there is no local point of contact
Siemens assumes no liability to the extent allowed under the law for any losses
resulting from a failure to comply with the aforementioned points or for the improper
compliance of the same.
5/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
2 Summary
2.1 Brief description
Applications 2-pipe fan coil units, 2-pipe with electric heater, 2-pipe with radiator/floor heating
4-pipe fan coil units, 4-pipe with electric heater
2-stage heating or cooling application
Compressors in dx-type equipment
Universal heating and/or cooling
Features 2 multifunctional inputs and 1 digital input for keycard contact, external sensor, etc.
Operating modes: Comfort, Economy and Protection
Automatic or manual heating/cooling changeover
Adjustable commissioning and control parameters
Minimum and maximum setpoint limitation
Backlit LCD
Selection of fan stage in the dead zone via P15
RDG100/RDG100T..:
On/Off, PWM or 3-position control outputs (triacs)
Output for 3-speed or 1-speed fan
AC 230 V operating voltage
RDG110..:
On/Off control outputs (relay, SPDT)
Output for 3-speed or 1-speed fan
AC 230 V operating voltage (RDG110)
AC/DC 24 V operating voltage (RDG110U)
RDG160T..:
DC 0...10 V or On/Off control outputs for actuators
DC 0...10 V or relay outputs for fan (ECM or 1-/3- speed)
AC/DC 24 V operating voltage
Functions Maintenance of room temperature via built-in temperature sensor or external room
temperature/return air temperature sensor
Automatic or manual changeover between heating and cooling mode
Selection of applications via DIP switches
Selection of operating mode via the operating mode button on the thermostat
1-speed, 3-speed or DC…10 V fan control (automatic or manual)
Display of current room temperature or setpoint in °C and/or °F
Minimum and maximum setpoint limitation
Button lock (automatic or manual)
1 digital input, freely selectable for:
– Operating mode switchover contact (keycard)
– Automatic heating/cooling changeover contact
– Electric heater enable
– Dewpoint sensor
6/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
– Fault input
2 multifunctional inputs, freely selectable for:
– Operating mode switchover contact (keycard)
– Automatic heating/cooling changeover sensor
– External room temperature or return air temperature
– Dewpoint sensor
– Electric heater enable
– Fault input
– Supply air temperature sensor (RDG160T..)
Advanced fan control function, i.e. fan kick, fan start, selectable fan operation
(enable, disable or depending on heating or cooling mode)
Purge function together with 2-port valve in a 2-pipe changeover system
Reminder to clean filters
Floor heating temperature limit
Minimum and maximum supply air temperature limitation (RDG160T..)
Reloading factory settings for commissioning and control parameters
7-day time program: 8 programmable timers to switch over between Comfort and
Economy mode (RDG100T, RDG160T.., RDG100T/H)
Infrared remote control (RDG100T, RDG160T.., RDG100T/H)
Selectable relay function (RDG160T..)
– For switching OFF external equipment OFF during Protection mode
– For switching ON external equipment (e.g. pump) during H/C demand
– Output heating/cooling sequence
Wizard function to select working temperature unit °C or °F (RDG160TU,
RDG110U)
Product Features UL
no.
Operating voltage
Infrared receiver
Backlit LCD
)
1
DC
3-speed
2)
3) 3) 3)
RDG100 AC 230 V 3 2 2
3) 3) 3) 5)
RDG100T AC 230 V 3 2 2 ( )
3) 3) 3) 5)
RDG100T/H AC 230 V 3 2 2 ( )
4)
RDG110 AC 230 V 2
4)
RDG110U AC/DC 24 V 2
5)
RDG160T AC/DC 24 V 2 ( )
6) 6) 5)
2 2 ( )
5)
RDG160TU AC/DC 24 V 2 ( )
6) 6) 5)
2 2 ( )
1)
Infrared remote control must be ordered as a separate item
2)
ECM fan output DC 0…10 V
3)
On/Off, PWM or 3-position (triac outputs)
4)
Relay output (SPDT)
5)
Can be disabled via P02 (or via DIP switches on RDG160T..)
6)
Either On/Off (relay output) or DC control signal
7/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
2.3 Equipment combinations
Description Product no. Data Sheet
8/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Electromotoric actuator, DC 0...10 V
SQS65.. 4573
(for valves 5.5 mm (0.2"))
Electrothermal actuator,
AC 24 V, NC, DC 0…10 V, 2 m (6.6 feet)
STA63 4884
(for radiator valves and small valves 2.5 mm
(0.1"))
Electrothermal actuator,
AC 24 V, NO, DC 0…10 V, 2 m (6.6 feet)
STP63 4884
(for radiator valves and small valves 2.5 mm
(0.1"))
*)
With PWM control, it is not possible to ensure exact parallel running of 2 or more thermal actuators.
If several fan coil systems are controlled by the same room thermostat, preference should be given to
motorized actuators with On/Off or 3-position control.
Note For more information about parallel operation and the maximum number of actuators that can
be used, refer to Data Sheets of the selected type of actuator and the following list:
2.4 Accessories
Description Product no. Data Sheet
Changeover mounting kit (50 pcs/package) ARG86.3 3009
2.5 Ordering
Product no. Stock no. Designation
RDG100 S55770-T158 Room thermostat
RDG100T S55770-T159 Room thermostat, with timer
RDG100T/H S55770-T235 Room thermostat, with timer, landscape housing
RDG110 S55770-T160 Room thermostat with relay outputs (AC 230 V)
RDG110U S55770-T361 Room thermostat with relay outputs (AC/DC 24 V), UL
certified
RDG160T S55770-T343 Room thermostat with timer and DC (or On/Off) output
for valve and fan (AC/DC 24 V)
RDG160TU S55770-T362 Room thermostat with timer and DC (or On/Off) output
for valve and fan (AC/DC 24 V), UL certified
9/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
3 Use
The RDG1.. room thermostats are designed for use with the following types of system:
10/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4 Functions
4.1 Temperature control
General note Setting of the control parameters (P01, etc., mentioned throughout the document) is
described in section 4.15.
The thermostat acquires the room temperature via built-in sensor, external room
temperature sensor (QAA32), or external return air temperature sensor (QAH11.1),
and maintains the setpoint by delivering actuator control commands to heating and/or
cooling equipment. The following control outputs are available depending on the
thermostat type:
1-speed/3-speed fan:
On/Off control on RDG100, RDG100T, RDG100T/H, RDG110..
Modulating PI/P control with 3-position control output on RDG100, RDG100T,
RDG100T/H
Modulating PI/P control with PWM output on RDG100, RDG100T, RDG100T/H
Modulating PI/P control with DC 0…10 V control output on RDG160T..
ECM fan:
On/Off control on RDG160T..
Modulating PI/P control with DC 0…10 V control output on RDG160T..
The switching differential or proportional band is 2 K (4 °F) for heating mode and 1 K
(2 °F) for cooling mode (adjustable via parameters P30 and P31).
The integral action time for modulating PI control is adjustable via parameter P35.
Temperature unit The temperature unit selection wizard enables to select the preferable temperature
selection wizard unit display on thermostats between °C and °F under the following two situations:
(only for 1. Select the application via the DIP switches at the rear of thermostat before fitting
RDG110U/RDG160TU) the front housing to the mounting plate.
2. Power up the thermostat after successfully connecting the line power.
Notes Pressing button (Esc) does not confirm the temperature selection.
If the temperature unit is not selected, °C is used by default.
Display The display shows the acquired room temperature or the Comfort setpoint, selectable
via parameter P06. The factory setting displays the current room temperature.
Use parameter P04 to display the room temperature or setpoint in °F rather than °C as
needed.
Concurrent display of Concurrent display of the current temperature or setpoint in °C and °F (parameter
°C and °F P07) is possible on the thermostats without 7-day time program.
11/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.2 Operating modes
Select the thermostat's operating mode via the operating mode button on the unit or
operating mode input (e.g. keycard occupancy sensor), when X1, X2, or D1 is set to 3
(P38, P40, P42). A corresponding setpoint is used to maintain the room temperature at
the desired level depending on the active operating mode. The following operating
modes are available:
Comfort mode In Comfort mode, the thermostat maintains the room temperature setpoint which can
be adjusted via the rotary knob. The fan can be set to automatic or manual fan
speed: low, medium or high.
Economy mode Economy mode helps save energy. Select it by pressing the operating mode button if
parameter P02 is set accordingly, or if the external operating mode switchover contact
is active (e.g. window contact).
Note If the external operating mode switchover contact is active, user operations are
ineffective and OFF is displayed. Control will then be according to Economy setpoints
(P11 and P12).
Auto Timer mode In Auto Timer mode , the thermostat automatically changes from Comfort to
(with RDG100T, Economy mode according to the 8 preprogrammed timers.
RDG100T/H, The display shows the Auto Timer mode symbol along with the symbol for the
RDG160T.. only) current operating mode (Comfort or Economy ).
Automatic is the default fan speed in Auto Timer mode.
Auto Timer function can be disabled with parameter P02 = 3, 4 or via DIP switch 5 on
RDG160T..
Operating mode button The behavior of the operating mode button can be selected via parameter P02:
12/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.3 Room temperature setpoints
Comfort mode The factory setting for the Comfort basic setpoint is 21 °C (70 °F) and can be changed
via parameter P08.
The setpoint in Comfort mode can be adjusted via the rotary knob.
Temporary setpoint If the "Temporary setpoint function" is enabled via parameter P69, the setpoint
adjusted via the rotary knob is set back to the Comfort basic setpoint when the
operating mode changes.
Setpoint limitation For comfort or energy saving purposes, the setpoint setting range can be limited to
minimum (P09) and maximum (P10).
P09 < P10 If the minimum limit P09 is set lower than the maximum limit P10, both heating and
(comfort concept) cooling are adjustable between these 2 limits.
The customer adjusts the desired setpoint and the thermostat controls the room
temperature accordingly.
*)
For 4-pipe applications , the selected comfort setpoint is in the middle of the dead
zone (P33). The unit stops to energize the heating/cooling outputs as soon as the
room temperature reaches the dead zone.
Example Cooling setpoint adjustable 18…25 °C (64…77 °F)
Heating setpoint adjustable 18…25 °C (64…77 °F)
P09 P10 If the minimum limit P09 is set higher than the limit P10, then
(energy saving concept) – The setting range of cooling setpoint is from P09…40 °C (P09…104 °F) in place
of 5…40 °C (41…104 °F)
– The setting range of heating setpoint is from 5…P10 °C (41…P10 °F) in place of
5…40 °C (41…104 °F)
This allows the user to limit the maximum heating setpoint and the minimum cooling
setpoint. This concept helps to save energy costs.
For 4-pipe applications:
– The thermostat runs with the setpoint of the active sequence:
In heating mode, the heating setpoint is active and adjustable via rotary knob.
In cooling mode, the cooling setpoint is active and adjustable via rotary knob.
– Switching from the heating setpoint to the cooling setpoint and vice-versa
occurs when the room temperature reaches the adjusted limitation (P09 or
P10) of the inactive sequence. E.g. the thermostat is in heating sequence and
runs with the heating setpoint. When the room temperature reaches P09, the
thermostat switches to cooling mode and runs with the cooling setpoint, as
long as the room temperature does not drop below P10.
Example Cooling setpoint adjustable 25…40 °C (77…104 °F)
Heating setpoint adjustable 5…21 °C (41…70 °F)
Economy mode Use control parameters P11 and P12 to adjust the Economy mode setpoints.
The heating setpoint is factory-set to 15 °C (59 °F), and the cooling setpoint to 30 °C
(86 °F).
13/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Protection mode Use control parameters P65 and P66 to adjust the Protection mode setpoints.
The heating setpoint is factory-set to 8 °C (46 °F) (frost protection) and to OFF for
cooling.
Caution If a setpoint is set to OFF (P65, P66), the thermostat does not maintain the setpoint in
the corresponding mode (heating or cooling).
This means no protective heating or cooling function and thus risk of frost in the
heating mode or risk of overtemperature in cooling mode!
The Economy setpoints are accessible at the service level (P11, P12); the Protection
setpoints at the expert level (P65, P66).
On changeover applications, the Comfort setpoints for heating and cooling sequence
are the same (w).
On 2-pipe applications with electric heater, the Comfort setpoint is either at the first
heating sequence (in heating mode) or at the cooling sequence (in cooling mode).
On 2-pipe applications with radiator, the Comfort setpoint is either at the radiator
sequence (in heating mode) or at the cooling sequence (in cooling mode).
The setpoints for Economy and Protection mode are below the Comfort setpoints
(heating) and above the Comfort setpoints (cooling). They can be set via parameters
P11, P12 (Economy mode) and P65, P66 (Protection mode).
Y Y Y Y
2-pipe
W T W T W HeatEco/Prot T W CoolEco/Prot T
2)
YE YE1) YE
2)
YE
1)
2-pipe Y Y Y Y
and electric
heater
W T W T W HeatEco/Prot T W HeatEco/Prot W CoolEco/Prot T
YR YR YR YR
Y Y Y Y
2-pipe
and radiator
W T W T W HeatEco/Prot T W HeatEco/Prot W CoolEco/Prot T
Y Y Y Y
2-stage heating
or cooling
W T W T W HeatEco/Prot T W CoolEco/Prot T
14/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
1) If P13 = ON
2) In case of manual changeover (P01=2), the first heating sequence is disabled to prevent heating (electric
heater) and cooling (coil) at the same time
On 4-pipe applications, the Comfort setpoint (w) is in the middle of the dead zone,
between the heating and cooling sequence.
The dead zone can be adjusted via parameter P33.
If manual changeover is selected, then either the cooling sequence or the heating
sequence is released. In this case, the Comfort setpoint is at the selected heating or
cooling sequence.
Application Economy/Protection
Comfort mode
mode
1) 1)
Heating and Cooling Heating mode Cooling mode Heating and/or cooling
Y Y Y Y
4-pipe
W T W T W T W HeatEco/Prot W CoolEco/Prot T
YE YE YE
Y Y Y Y
4-pipe and electric
heater
W T W T W T W HeatEco/Prot W CoolEco/Prot T
1)
Manual changeover, P01=2
15/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.5 Applications overview
The thermostats support the following applications, which can be configured via DIP
switches at the rear of the unit. Depending on the type of thermostat, On/Off or
modulating control outputs are available.
heating
3076S02_01
YE
B2
B2 T B2
T T T T
T
(B1) (B1) (B1)
YHC
YHC YHC
M1 M1 M1
T T
T
(B1) (B1) (B1)
YR
1 2 3 4 5
and electric heater OFF
1 2 3 4 5
1 2 3 4 5
3076S 05_01
YE
T B2
B2 YHC2
T YC T T
(B1) (B1) YC (B1)
YHC1
YH
YH
M1 M1 M1
T T T
(B1) (B1) (B1)
16/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.5.2 Applications for Universal systems
Applications, DIP setting, Control outputs
ON ON ON
Chilled/heated Chilled/heated ceiling Chilled/heated
ceiling OFF
1 2 3 4 5
and electric heater OFF
1 2 3 4 5
ceiling and radiator OFF
1 2 3 4 5
/floor heating
3191S14
3191S12
3191S11
B2 D3 B2 D3 B2 D3
T T T
N1 T N1 YR N1
T T
D3
YHC1 YC
T
B1
YHC2
YH N1
T
17/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.5.3 Applications for heat pump systems (RDG110.., RDG160T..)
Applications, DIP setting, Control outputs
ON ON
Heated or cooled with compressors Heated or cooled with compressors
OFF
1 2 3 4 5
with electric heater OFF
1 2 3 4 5
3181S31
3181S32
D3 D3
T T
B1
B1
YE
T N1
T N1
1 2 3 4 5
3181S36
3181S35
D3 D3
T T
B1 B1
2 T N1
T N1
Notes RDG100..
Use P46/P47 to change output from On/Off (factory setting) to PWM.
Use DIP switches 4 and 5 to change output from On/Off to 3-position.
RDG110..
Select DIP switches "OFF OFF ON" for application with reverse valve, see section
4.7.11.
RDG160T..
Use P46/P47 to change valve actuator output from DC (factory setting) to On/Off.
Use DIP switch 4 to change fan output from DC (factory setting) to 3-speed.
18/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.6 Additional features
Automatic The water temperature acquired by the changeover sensor (QAH11.1 + ARG86.3) is
heating/cooling used to change over from heating to cooling mode, or vice versa.
changeover When the water temperature is above 28 °C (82 °F) (adjustable via parameter
P37), the thermostat changes over to heating mode.
It stays in heating mode until the temperature falls below 16°C (61 °F) (adjustable
via parameter P36)
When the water temperature is below 16 °C (61 °F) (P36), the thermostat changes
over to cooling mode.
It stays in cooling mode until the temperature rises above 28°C (82 °F) (P37).
If the water temperature is between the 2 changeover points immediately after
power-up (inside the hysteresis), the thermostat starts in previous mode.
The water temperature is acquired at 30-second intervals and the operating state is
updated accordingly.
Remote heating/ The QAH11.1 cable temperature sensor for automatic heating/cooling changeover can
cooling changeover be replaced by an external switch for manual, remote changeover:
Manual heating/cooling Manual heating/cooling changeover means selection via changeover button on the
changeover thermostat by repeatedly pushing the button until the required mode is shown on
the display (automatic changeover is done via an external sensor/switch connected
to X1, X2, or D1)
If manual heating/cooling changeover is commissioned (P01 = 2), then
heating/cooling mode cannot be changed via changeover sensor/switch; it will
remain in the last mode as selected locally via button.
External/return air The thermostat acquires the room temperature via built-in sensor, external room
temperature sensor temperature sensor (QAA32), or external return air temperature sensor (QAH11.1)
connected to multifunctional input X1 or X2.
Inputs X1 or X2 must be commissioned accordingly. See section 4.10.
Purge function
19/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
The changeover sensor ensures changeover from heating to cooling mode based on
the acquired water temperature. We recommend activating the purge function
(parameter P50) with 2-port valves. This function ensures correct acquisition of the
medium temperature even if the 2-port valve is closed for an extended period of time.
The valve is then opened for 1 to 5 minutes (adjustable) at 2-hour intervals during off
hours. This function is available on all RDG variants for applications 2-pipe
changeover and on RDG160T.. also for the 4-pipe changeover.
Caution The purge function (parameter P50) must be disabled if the thermostat is used in
compressor-based applications.
Avoid damage from In very warm and humid climates, the fan can be run periodically or continuously at a
moisture low fan speed (e.g. in empty apartments or shops) in Economy mode by setting
parameter P61, in order to avoid damage from moisture due to lack of air circulation.
See also section 4.9 for details.
Minimum output Limit the On/Off switching cycle to protect the compressor and reduce wear and tear.
on-time/off-time The minimum output on-time and off-time for On/Off control output can be adjusted
from 1 to 20 minutes via parameters P48 and P49.
The factory setting is 1 minute.
Readjusting the setpoint or heating/cooling mode changeover immediately results in
calculation of the output status; output Y11/Y21 may not hold the minimum 1-minute
On/Off time.
If parameter P48 or P49 is set to above 1 minute, the minimum On/Off time for the
control output is maintained as set, even if the setpoint or changeover mode is
readjusted.
This function is only available for On/Off control with RDG100, RDG100T,
RDG100T/H, RDG110.., and RDG160T...
Floor heating/ All heating sequences can also be used for floor heating.
Floor cooling You can use fan coil heating/cooling sequences for floor heating or cooling by
disabling the fan via parameter P52.
Floor temperature The temperature should be limited for 2 reasons: comfort and protection of the floor.
limitation function
The floor temperature sensor, connected to multifunctional input X1 or X2, acquires
the floor temperature. If the temperature exceeds the parameterized limit (parameter
P51), the heating valve is fully closed until the floor temperature drops to a level
2 K (4 °F) below the parameterized limit.
This function is factory-set to OFF (disabled).
Input X1 or X2 must be commissioned accordingly (P38 or P40 = 1).
See section 4.10 for details.
Recommended values Living rooms:
for P51: Up to 26 °C (79 °F) for long-term presence, up to 28 °C (82 °F) for short-time
presence.
Bath rooms:
Up to 28 °C (82 °F) for long-term presence, up to 30 °C (86 °F) for short-time
presence.
20/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
The table below shows the relation between parameter, temperature source and
temperature display:
External temp. sensor Source for display of room Floor temp. limit
Parameter P51 Output control according to
available temperature function
OFF No Built-in sensor Built-in sensor Not active
OFF Yes External temp. sensor External temp. sensor Not active
10… No Built-in sensor Built-in sensor Not active
Built-in sensor + limit by
Yes Built-in sensor Active
external sensor
The floor temperature limitation function influences the outputs listed in the table
below:
Floor temp. limit function has influence on
t t
Heat. mode Cool. mode Heat. and cool.
Application Output Y1 Output Y2 Output Y3 (P01=0/2/3) (P01=1/2/3) mode (P01=4) Remark
2-pipe H/C valve Y1 N/A
2-pipe and electric heater H/C valve Electric heater Y2 Y2 *) Only electric heater
2-pipe and radiator H/C valve Radiator Y2 Y2 Only radiator
4-pipe Heating valve Cooling valve Y1 N/A Y1
4-pipe and electric heater Heating valve Cooling valve Electric heater Y3 N/A Y3 Only electric heater
2-stage 1st H/C 2nd H/C Y1, Y2 N/A
*)
If P13 = ON electric heater in cooling mode
Note Either floor temperature sensor or external room temperature sensor can be used.
Supply air temperature This function increases the comfort in the room by keeping the supply air temperature
limitation (RDG160T..) of the fan coil unit between the selected minimum and maximum temperature limits.
If the supply air temperature exceeds a limit, the thermostat reduces the
corresponding valve position until the supply air temperature is back in the limits.
In case the air flow is too low (especially with DC 0...10 V fans), this prevents cold air
from dumping into the room/warm air from bubbling straight up instead of circulating.
To enable this function, the multifunctional input, to which the supply air sensor is
connected, needs to be set to "Supply air sensor" (e.g. P38=9). Then the parameters
for the limits are visible (P63: minimum supply air temperature, P64: maximum supply
air temperature).
This function is only active in Comfort mode and can only be used with DC 0...10 V
actuators.
Note For applications with electric heater and radiator, this function is available only on the
cooling valve (in cooling mode).
Dewpoint monitoring Dewpoint monitoring is essential to prevent condensation on the chilled ceiling
(cooling with fan disabled, parameter P52). It helps avoid associated damage to the
building.
A dewpoint sensor with a potential-free contact is connected to multifunctional input
X1, X2 or D1. If there is condensation, the cooling valve is fully closed until no more
condensation is detected, and the cooling output is disabled temporarily.
The condensation symbol is displayed during temporary override.
The input must be commissioned accordingly (P38, P40, P42).
See section 4.10.
21/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Button lock If the button lock function is enabled by parameter P14, the buttons will be locked or
unlocked by pressing the right button for 3 seconds.
If "Auto lock" is configured, the thermostat will automatically lock the buttons 10
seconds after the last adjustment.
Operating mode The thermostat can be forced into Economy mode (e.g. when a window is opened).
switchover contact The window contact can be connected to digital input D1 (or multifunctional input X1,
(window contact) X2). Set parameter P42 (P38, P40) to 3.
Extended Comfort The left button switches the operating mode from Economy to Comfort for the period
mode (operating mode preset in P68, if the following conditions are fulfilled:
switchover contact The operating mode switchover contact is closed (connected to input X1, X2, D1,
closed) parameter P38, P40, P42 set to 3)
Parameter P68 (extend Comfort period) is greater than 0
During the temporary Comfort mode extension, sandglass symbol appears.
Temporary timer for The current operating mode can be forced temporarily into Comfort or
extension of Economy/Protection mode. The time period is adjusted via the rotary knob:
presence/absence Extend presence: Set the device to Comfort mode for the selected time period
Extend absence: Set the device to Economy/Protection mode for the selected time
period
To activate the function, keep the left button pressed and, within 3 seconds, turn the
rotary knob…
clockwise for extended presence
counterclockwise for extended absence
22/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Function without time program
User profile for operating mode Operating mode when Function Operating Operating
(selected via P02) activating function mode mode at
during the end of
function function
Comfort Extension Comfort Protection
P02 = 1:
Comfort Absence Protection Comfort
Comfort or Economy Extension Comfort Economy
P02 = 2:
Comfort or Economy Absence Economy Comfort
User profile for operating mode Operating mode when Function Operating Operating
(selected via P02) activating function mode mode at
during the end of
function function
Auto or comfort Extension Comfort Auto
P02 = 1:
Auto or comfort Absence Protection Auto
Auto, Comfort or Economy Extension Comfort Auto
P02 = 2
Auto, Comfort or Economy Absence Economy Auto
23/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.6.1 Qx- relay switching functions (RDG160T.. only)
The following special functions are available on the RDG160T.. and allow the control
of external equipment connected to the Q1, Q2 and Q3 relay outputs.
Switch OFF external equipment when the thermostat is in Protection Mode
Switch ON external equipment during heating/cooling demand
Output heating/cooling sequence
The relay output corresponding parameters need to be set to enable the function.
Function on Q1, set parameter P72. Test relay function via diagnostic d08.
Function on Q2, set parameter P73. Test relay function via diagnostic d09.
Function on Q3, set parameter P74. Test relay function via diagnostic d10.
Notes Those functions are available when DIP4 is set to OFF (EC fan).
It is not suggested to use those functions in combination with the On/Off valve
control (P46/P47=1) to guarantee the temperature accuracy. If this combination is
requested, the total maximum current on the relay outputs (Q1+Q2+Q3) should not
exceed 2A.
Switch OFF external The external equipment (such as: fan coil unit) can be switched OFF via relay output,
equipment in in order to reduce energy consumption when the thermostat is in Protection mode and
Protection mode no temperature control is requested.
The function can be enabled by setting the corresponding Qx- parameter to 1.
Relay contact is open when the thermostat is in protection mode.
Switch ON contact During the heating or cooling demand, the relay contact can be energized to control
during Heat/Cool an external equipment, for example to run the pump of a water system (fan coil).
demand
To reduce the wear and tear of the HVAC equipment, the minimum output on-time and
off-time of the Qx- relay output can be adjusted from 1 to 20 minutes via parameters
P48 and P49. The factory setting is 1 minute.
Note The relay output remains OFF if the heating is provided ONLY by electric heater
(application 2-pipe electric heater, heating by electric heater, cooling by fan coil) or
radiator.
2-pipe water system (with one pump):
Enable the function by selecting the corresponding output parameter to 2
Connect the external equipment to selected relay output
In case of heating/cooling demand, the output contact is energized
4-pipe water system (with two pumps):
The function can be enabled by selecting the correspondent output parameters
> set one parameter to 3. The output is energized during heating demand
> set one other parameter to 4. The output is energized during cooling demand
Connect the external equipment to the selected relay outputs
Output heating/cooling This function switches the relay output depending on the sequence, either heating or
sequence cooling. The output can be used for the release of a heat pump compressor.
When the thermostat is in heating mode (even in dead zone):
> the correspondent Qx- output contact is closed.
When the thermostat is in cooling mode (even in dead zone):
> the correspondent Qx- output contact is open.
The function can be enabled by setting the corresponding Qx- parameter to 5.
24/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.7 Control sequences
4.7.1 Sequences overview (setting via parameter P01)
Sequence
2-pipe,
2-pipe and electric
heater
2-pipe and radiator
4-pipe
2) 2)
4-pipe and electric
heater
2-stage heating or
cooling
1)
Notes Chilled/heated ceiling and radiator applications: see section 4.7.9;
Compressor applications: see section 4.7.10.
2)
Manual and automatic changeover for 4-pipe applications, see section 4.7.6:
– 4-pipe manual changeover (P01 = 2) means activating either cooling or
heating outputs.
– 4-pipe automatic changeover (P01 = 3) means swapping the control outputs
according to a heating/cooling sensor or remote switch (main and secondary
application), see section 4.7.6.
25/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.7.2 Control outputs configuration
(setting via DIP switches 4/5 and parameters)
Control outputs
On/Off Mod. PWM Mod. Mod. DC
(2-position) (2-pos.) 3-pos. 0…10 V
Fan 3-/1- 3-/1-speed,
3-/1-speed DC fan 3-/1-speed 3-/1-speed
control: speed DC fan
Applications Type: RDG10.. RDG110.. RDG160.. RDG10.. RDG10.. RDG160..
2-pipe
2-pipe and electric heater
2-pipe and radiator/floor heating
4-pipe
4-pipe and electric heater ( )*
2 stage, cooling or heating
*
Only possible for 1 actuator
RDG100.. With RDG100, RDG100T and RDG100T/H, the function of the control outputs
(2-position or 3-position) is set via DIP switches 4 and 5 .
3181D101
OFF OFF OFF OFF
1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5
Note If 2-position is selected, the factory setting is On/Off. If you want PWM (pulse width
modulation), set parameters P46 and/or P47 to 2 = PWM.
RDG110.. With RDG110.. only control output On/Off is available.
RDG160T.. With RDG160T.., the function of the control outputs (DC 0...10 V or 2-position) is set
via parameters P46 and P47.
Notes For applications with 3-speed fan, only DC 0...10 V control outputs on Y10, Y20 are
available
Type of fan signal can be selected via P53 or DIP4, see section 4.9.
2-position valve actuator control on applications without fan function – sequence of
settings:
– Set DIP 4 to Off and P53 = 3.
– Disable the fan function via parameter P52 = 0
– Set valve actuators to 2-position via P46 and/or P47 = 1
For details concerning connection of peripheral devices and setting of the DIP
switches, refer to the Mounting Instructions:
– [4] M3181.1 (RDG100, RDG100T)
26/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
– [5] M3181.2 (RDG110)
– [6] M3181.5 (RDG160T)
– [7] M3181.4 (RDG100T/H)
– [9] M3183.1 (RDG110U)
– [10] M3183.2 (RDG160TU)
Control sequence The diagrams below show the control sequence for modulating PI control.
modulating output
Heating mode Cooling mode
27/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.7.4 2-pipe fan coil unit with electric heater
Heating or cooling with On 2-pipe applications with electric heater, the thermostat controls a valve in
auxiliary heater heating/cooling mode with changeover, heating only, or cooling only plus an electric
heater.
Cooling only is factory set (P01=1) with enabled electric heater (P13).
Electric heating, active in In cooling mode, the valve receives an OPEN command if the acquired temperature is
cooling mode above the setpoint.
The electric heater receives an ON command if the acquired room temperature drops
below "setpoint" minus "dead zone" (= setpoint for electric heater) while the electric
heater is enabled (parameter P13 = on).
Note "Setpoint for electric heater" is limited by parameter "Maximum setpoint for Comfort
mode" (P10).
Electric heating in In heating mode, the valve receives an OPEN command if the acquired temperature is
heating mode below the setpoint. The electric heater is used as an additional heating source when
the heating energy controlled by the valve is insufficient.
The electric heater receives an ON command, if the temperature is below "setpoint"
minus "setpoint differential" (= setpoint for electric heater).
Electric heating and The electric heater is active in heating mode only and the control output for the valve
manual changeover is permanently disabled when manual changeover is selected (P01=2).
Digital input "Enable Remote enabling/disabling of the electric heater is possible via input X1, X2 or D1 for
electric heater" tariff regulations, energy savings, etc.
Input X1, X2, or D1 must be commissioned accordingly (parameters P38, P40, P42).
See section 4.10.
Caution An electric heater must always be protected by a safety thermostat!
On/Off electric heater With a DC 0...10 V (ECM) fan it is possible to select On/Off control for the electric
on RDG160T.. with heater by setting parameter P47 = 1. The electric heater has to be connected to
ECM fan output Q2.
The electric heater starts with a delay of 15 s, to make sure the fan delivers
sufficient air flow to dissipate the heat.
To avoid overheating of the electric heater, the thermostat guarantee at least a fan
speed II (middle value between Vmin (P56) – Vmax (P55)) when the electric heater
need to be energized.
Adaptive temperature compensation P45 need to be set accordingly
(Refer to section 4.8).
On/Off control
Control sequence The diagrams below show the control sequence for 2-position.
On/Off output
Heating mode Cooling mode
(automatic changeover = heating or heating only) (man./auto. changeover = cooling or cooling only)
28/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
(manual changeover = heating)
T[°C] Room temperature
W Room temperature setpoint
YHC Control command "Valve" or "Compressor"
YE Control command "Electric heater"
SDH Switching differential "Heating" (P30)
SDC Switching differential "Cooling" (P31)
Xdz Dead zone (P33)
wD Setpoint differential (P34)
Note RDG160T.. with manual changeover works in the same way as for automatic
changeover, with 2-stage heating.
29/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.7.5 2-pipe fan coil unit with radiator or floor heating
Heating or cooling with On 2-pipe applications with radiator, the thermostat controls a valve in heating/cooling
radiator or floor heating mode with changeover, heating only, or cooling only plus a radiator valve. Cooling only
is factory-set (P01=1).
Radiator, active in In cooling mode, the valve receives an OPEN command if the acquired temperature is
cooling mode above the setpoint.
The radiator receives an ON command if the acquired room temperature drops below
"setpoint" minus "dead zone" (= "setpoint for radiator").
Radiator in heating mode In heating mode, the radiator receives an OPEN command if the acquired temperature
is below the setpoint. The fan coil unit is used as an additional heat source when the
heat energy controlled by the radiator is insufficient.
The fan coil unit receives an ON command if the temperature is below "setpoint"
minus "setpoint differential" (= setpoint for fan coil unit).
Floor heating The radiator sequence can also be used for floor heating.
The "Floor heating limitation function" is described on page 20.
On/Off control The diagrams below show the control sequence for 2-position control.
Heating mode Cooling mode
30/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Setting the sequence and the control outputs
Refer to section 4.5, 4.7.1 and 4.7.2.
Heating and cooling On 4-pipe applications, the thermostat controls 2 valves in heating and cooling mode,
heating/cooling mode by manual selection, or heating and cooling mode with
changeover. Heating and cooling mode (P01=4) is factory-set.
4-pipe application with The heating or cooling output can be released via operating mode button if parameter
manual changeover P01 is set to manual (P01=2).
"Main and secondary" If parameter P01 is set to changeover (P01=3), the heating and cooling output is
application (4-pipe with swapped according to the changeover sensor input status (see automatic heating and
changeover) cooling changeover sensor, section 4.6). This mode is used for the so-called "Main
and secondary" application. This is a 4-pipe fan coil unit system with different capacity
of the 2 coils. The water circuit is changed to optimize the energy exchange
depending on the season (summer/winter):
– Winter: Large coil (V1) for heating, small coil (V2) for cooling
– Summer: Large coil (V1) for cooling, small coil (V2) for heating
3181D112
T B2 V2
Note:
This example shows
V1 On/Off control;
M1
for modulating con-
trol, connect the
appropriate output
T
B1 terminals.
Notes The factory setting for the heating and cooling changeover sensor (B2 in the above
diagram) is input X2 (P40 = 2)
The thermostat assumes winter operation when B2 > P37
(factory setting 28 °C (82 °F))
The thermostat assumes summer operation when B2 < P36
(factory setting 16 °C (61 °F))
31/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
On/Off control The diagrams below show the control sequence for 2-position control.
Heating mode with manual selection Cooling mode with manual selection
(P01=2) or (P01=2) or
*) *)
for P09 >= P10 in heating sequence for P09 >= P10 in cooling sequence
*)
see section 4.3.
32/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.7.7 4-pipe fan coil unit with electric heater (RDG100..)
Heating and cooling with On 4-pipe applications with electric heater, the thermostat controls 2 valves in heating
auxiliary heater and cooling mode by manual selection, heating and cooling mode with automatic
changeover, heating only, or cooling only plus an electric heater.
Heating and cooling is factory-set (P01=4).
Electric heating in The electric heater is used as an additional heat source when the heating energy
heating mode controlled by the valve is insufficient.
The electric heater receives an ON command when the temperature is below
"setpoint" minus "1/2 dead zone" minus "setpoint differential" (= "setpoint for electric
heater").
Digital input "Enable Remote enabling/disabling of the electric heater is possible via input X1, X2, or D1 for
electric heater" tariff regulations, energy saving, etc.
Input X1, X2, or D1 must be commissioned accordingly (parameters P38, P40, P42).
See section 4.10 for details.
Caution An electric heater must always be protected by a safety thermostat!
4-pipe application with The heating or cooling output can be released via operating mode button if parameter
manual changeover P01 is set to manual (P01=2).
On/Off control The diagrams below show the control sequence for 2-position control.
Heating mode with manual selection (P01=2) Cooling mode with manual selection P01=2)
33/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Modulating control: 3-position or PWM
Heating mode with manual selection (P01=2) Cooling mode with manual selection P01=2)
34/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.7.8 2-stage heating or cooling
2-stage heating On 2-stage applications, the thermostat controls 2 valves or compressors in heating or
or cooling cooling mode or changeover (automatic or manual).
"Cooling only" is factory-set (P01=1).
Heating mode In heating mode, the 1st stage is activated if the acquired temperature is below the
setpoint.
The 2nd stage is activated if the acquired room temperature drops below "setpoint"
minus "setpoint differential".
Cooling mode In cooling mode, the 1st stage is activated if the acquired temperature is above the
setpoint.
The 2nd stage is activated if the acquired room temperature rises above "setpoint"
plus "setpoint differential".
On/Off control The diagrams below show the control sequence for 2-position control.
35/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Modulating control: 3-position, PWM or DC 0…10 V
36/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.7.9 Chilled/heated ceiling and radiator applications
Refer to section 4.5.2 for details about the product type and control outputs.
RDG160TU
RDG110U
RDG160T
radiator RDG110
37/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.7.11 1-stage heating or cooling with reversing valve (RDG110..)
ON
OFF
1 2 3
RV C1
On/Off control The diagrams below show the control sequences for 2-position control.
Heating mode with manual selection Cooling mode with manual selection
(P01 = 2) (P01 = 2)
38/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.8 Control outputs
Overview of control Different control output signals are available depending on the thermostat type, the
outputs position of DIP switches 4 and 5, and parameters P46 and P47 (see section 4.7.2).
Product no.
RDG100 Y1, Y2, Y3 Y1, Y3, Y1/Y2, Y3/Y4
RDG100T (3 x N.O.) (2 x PWM) (2 x / )
RDG100T/H
RDG110 Y11/Y12,
RDG110U Y21/Y22 (2 x
SPDT)
RDG160T Q1, Q2 Y10, Y20
RDG160TU (2 x N.O.) (2 x DC 0…10 V)
On/Off control signal The valve or compressor receives the ON command via control output Y1 or Y3
(2-position) (RDG110..: Y11/Y21, RDG160T..: Q1/Q2) when
1. the acquired room temperature is below the setpoint (heating mode) or above the
setpoint (cooling mode).
2. the control outputs have been inactive for more than the "Minimum output off-time"
(factory setting 1 minute, adjustable via parameter P48).
Electric heater control The electric heater receives an ON command via the auxiliary heating control output
signal (On/Off) (Y.., see Mounting Instructions) when
1. the acquired room temperature is below "Setpoint for electric heater"
2. the electric heater has been switched off for at least 1 minute
Note! On RDG160T.. the electric heater can be controlled via the 2-position output (Q2) by
setting P47 = 1.
39/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Adaptive temperature When an electric heater is connected directly to the On/Off output (RDG160T..: Q2,
compensation for electric RDG110..:Y21), the current causes the relay contact to heat up. This falsifies the
heater (RDG160T.., reading of the internal temperature sensor. The thermostat compensates the
RDG110..) temperature if the rated current/power of the electric heating is entered in the
parameters.
RDG160T..:
P45 (power electric heater): Factory setting: 0.0 kW, setting range: 0.0…1.2 kW.
RDG110:
P46 (load current electric heater): Factory setting: 1 A, setting range: 1…5 A.
RDG110U:
P46 is not available for AC 24 V operating voltage with electric heater controlled via
external relay.
3-position This function is available with RDG100, RDG100T and RDG100T/H only.
control signal
Heating: Output Y1 provides the OPEN command, and Y2 the CLOSE command to
the 3-position actuator. Relay function Y1/Y2 and wiring can be tested via diagnostic
parameter d05. Cooling: Idem with Y3 and Y4. Relay function Y3/Y4 and wiring can be
tested via diagnostic parameter d06.
The factory setting for the actuator's running time is 150 seconds. It can be adjusted
via parameters P44 (Y1 and Y2) or P45 (Y3 and Y4).
The parameters are only visible if 3-position is selected via DIP switches 4 and 5.
Synchronization 1. When the thermostat is powered up, a closing command for the actuator running
time + 150% is provided to ensure that the actuator fully closes and synchronizes
to the control algorithm.
2. When the thermostat calculates the positions "fully close" or "fully open", the
actuator's running time is extended + 150% to ensure the right actuator position is
synchronized to the control algorithm.
3. After the actuator reaches the position calculated by the thermostat, a waiting time
of 30 seconds is applied to stabilize the outputs.
PWM control This function is available with RDG100, RDG100T and RDG100T/H only.
The demand calculated by PI control from the current room temperature and setpoint
is provided via Y1 and Y3 to the valve actuator as a PWM signal (pulse width
modulation) for thermal actuators. The output is activated for a period proportional to
the heating/cooling demand and then switched off for the rest of the PWM interval.
The interval is 150 seconds (factory setting). It can be adjusted via parameters P44
(Y1) or P45 (Y3). These parameters are only visible if 2-position is selected via DIP
switches 4 and 5 and if PWM is selected via P46 and P47.
Note! For PWM, the integral time (P35) must be set to 0.
PWM for thermal valve For thermal valve actuators, set the running time to 240 seconds.
actuators
Note! Never apply PWM to an electromotoric actuator.
It is not possible to ensure exact parallel running of 2 or more thermal valve
actuator. If several fan coil units are driven by the same thermostat, preference
should be given to electromotoric actuators with On/Off or 3-position position
control.
PWM for electric heaters For electric heaters, set the running time to 90 seconds.
40/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
To avoid burn-off of mechanical contacts by frequent switching, use a current valve in
place of a relay or contactor.
Note! For PWM, the integral time (P35) must be set to 0.
DC 0...10 V The demand calculated by PI control from the current room temperature and setpoint
for valve actuators is provided via Y10 and Y20 to the valve actuator as a continuous
DC 0...10 V signal.
DC 0...10 V For applications with 3-speed fan, the electric heater can be controlled only via DC
for electric heaters output.
The demand calculated by PI control from the current room temperature and
setpoint is provided via Y20 as a continuous DC 0...10 V signal.
The signal converter (SEM61.4) converts the DC 0...10 V signal to AC 24 V PDM
pulses for the current valve.
The current valve (SEA45.1) supplies the electric heater with AC 50…660 V pulsed
current.
Note! For applications with ECM fan (DC signal) on RDG160T.., the electric heater can be
controlled via the On/Off output (Q2) by setting P47 = 1.
Adaptive temperature compensation: see 4.7.4.
L
3181D21
G
FF
G Y E F...
Y PWM
N1 AC 24 V U1
G0 Y1 G
N1 RDG160T..
DC 0 ... 10 V
U1 Signal converter SEM61.4 (see Data
Y1 G L Sheet N5102)
Y1 Current valve SEA45.1 (see Data
Y1 Sheet N4937)
Q
K… Safety loop (e.g. safety thermostat
G0
K... and high-temperature cutout)
5.7 kW FF Very fast-acting fuse
max. F… Overcurrent trip
N
41/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.9 Fan control
Overview of fan Different fan output signals are available depending on the thermostat type:
outputs
Control output 2 On/Off Modulating Control type
1-/3-speed fan fan selected via
DC 0…10 V
Product no.
RDG100, RDG100T, Q1,Q2,Q3 (3) P53
RDG100T/H
RDG110.. Q1,Q2,Q3 (3) P53
1) 1)
RDG160T.. Q1,Q2,Q3 (3) Y50 (1) P53, DIP 4
( ) Number of outputs
1)
Selectable via P53 or DIP switch 4 on RDG160T..
The fan operates in automatic mode or at the selected speed with manual mode.
In automatic mode, the fan speed depends on the setpoint and the current room
temperature. When the room temperature reaches the setpoint, the control valve
closes and the fan switches off or stays at fan speed I (minimum fan speed) according
to the setting of parameters P15 and P60.
Factory setting for "Fan in the dead zone":
Fan speed OFF: P15 = 0, P60 = OFF.
Selection fan output The type of the fan output (DC 0...10 V, 3-speed or 1-speed) can be set via
on RDG160T.. DIP switch 4, local HMI (P53).
If application is set via DIP switches and DIP 4 = Off:
DC 0...10 V fan (ECM) on Y50 is selected
Parameter P53 = 3 (ECM fan) cannot be modified
1-speed/3-speed fan output is not selectable
If application is set via DIP switches and DIP 4 = On
3-speed fan on Q1, Q2, Q3 is selected, parameter P53 = 2
1-speed fan (on Q1) can be selected via HMI (P53 = 1)
DC 0...10 V (ECM) fan output is not selectable
3-speed fan output is enabled only if the application has also been selected
42/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
3-speed fan control The individual switching points for ON of each fan stage can be adjusted via control
with modulating parameters P55…P57. The fan speed switch off point is 20% below the switch on
heating/cooling control point. The diagrams below show fan speed control for modulating PI control.
(PWM, 3-pos or
DC 0...10 V)
Heating/Cooling
Heating/Cooling
Look-up table with SDH/SDC [K] 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 >4.5
On/Off control XpHFan/XpCFan [K] 2 3 4 5 6 7 8 9 10
43/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
1-speed/3-speed fan The thermostat can control a 1-speed or 3-speed fan (selected via control parameter
P53).
A 1-speed fan is connected to terminal Q1, a 3-speed fan to terminals Q1, Q2 and Q3.
Control sequence When DC 0...10 V Fan and DC 0...10 V valve output control is selected, the fan
for DC 0...10 V fan switching points can be set via the following parameters:
(ECM) and DC 0...10 V – P55: ECM fan max. output
valves (RDG160T..) – P56: ECM fan min. output
– P57: Switching point fan
Y
3 19 1Z114 _01
100%
Xdz
100%
Fan III
Fan II
= Note: The control signals
=
Fan_max "Heating" and "Cooling" are not
Fan I
Fan_min influenced by the manual
0%
w T[°C] setting of fan speeds.
Xdz
Note By heating only with electric heater, manual fan speed 1 I cannot be selected to
guarantee the necessary minimum air flow for the electric heater and to avoid
overheating of the system.
2 sequences For heating or cooling with 2 sequences (e.g. heating with a heating coil and an
heating/cooling electric heater, or 2-stage cooling), the fan is always synchronized with the first
sequence.
Fan operation as per Fan operation can be limited to be active with cooling only or heating only, or even be
heating/cooling mode, totally disabled via control parameter "Fan operation" P52.
or disabled When fan operation is disabled, the fan symbol on the display disappears and
pressing the fan button has no impact.
This function allows you to use the thermostat on universal applications such as
chilled/heated ceilings and radiator, etc. (see section 4.7.9).
44/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Fan minimum In automatic mode, a dwelling time of 2 minutes (factory setting) is active. The fan
on- time maintains each speed for at least 2 minutes before it changes to the next speed. This
minimum on-time can be adjusted from 1…6 minutes via parameter P59.
Fan kick P60, P61 In automatic fan mode and with the room temperature in the dead zone, the control
valve is normally closed and the fan disabled. With the "Fan kick" function, the fan can
be released from time to time at low speed for minimum on-time (see above) even if
the valve is closed.
This function can be used to avoid damage from moisture due to a lack of air circu-
lation, or to allow a return air temperature sensor to acquire the correct room
temperature.
Y
Q1
0
t [h:mm]
The periodic fan kick time can be selected individually for Comfort mode via parameter
P60, and for Economy mode via parameter P61.
Note Fan kick value "0" means the fan runs continuously in the dead zone.
Fan kick value “1” and higher: value in minutes
Fan kick value "OFF" means the fan does not run in the dead zone.
Fan operation in dead Via parameter P15 in "Service Level", the fan speed in the dead zone (in Comfort
zone P15 mode) can be set according to customer preference.
The following options are available:
Fan does not run in the dead zone (P15=0)
Fan runs at low speed in Heating and Cooling mode (P15=1)
Fan runs at low speed in Cooling mode only (P15=2)
The functions "Fan in dead zone" (P15) and "Fan kick" (P60) are combined as follows:
P60 = 0 Fan runs continuously in the dead zone, P15 has no influence
P60 = OFF Fan operation in dead zone according to P15
Fan start When the fan starts from standstill, it starts at speed 3 III for 1 second to ensure safe
fan motor start by overcoming inertia and friction (selected via parameter P58).
Q 1 sec
3181D22
Q3
Q2
Q1
0
T
Fan overrun for electric When the electric heater is switched off, the fan overruns for 60 seconds (parameter
heater P54) to avoid overtemperature of the electric heater or prevent the thermal cutout from
responding.
45/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Fan failure In case of fan failure, the thermostat cannot protect the electric heater against
overtemperature. For this reason, the electric heater must feature a separate safety
device (thermal cutout).
Clean fan filter The "Clean fan filter reminder" function counts the fan operating hours and displays
reminder message "FIL " to remind the user to change/clean the fan filter as soon as the
threshold is reached. This does not impact the thermostat's operation, which continues
to run normally. The function is set via parameter P62 (default = Off (0)).
The "Clean filter reminder" is reset when the operating mode is manually set to
Protection and back.
Fan in Auto Timer In Auto Timer mode , the default fan mode is automatic. The fan mode can be
mode (RDG1..T) changed to Manual by pressing the FAN button. The fan returns to the automatic
default mode after each switchover from Comfort to Economy mode, and vice versa.
Fan start delay To let the heating/cooling coil reach its temperature, the fan start can be delayed by a
time period set via parameter P67.
Function available with:
RDG100..: On/Off control outputs
RDG110..: On/Off control outputs
RDG160T..: On/Off and DC control outputs, 3-speed and DC fan
Y
3181D23
0 T
P67
46/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.10 Multifunctional input, digital input
The thermostat has 2 multifunctional inputs X1 and X2 and a digital input D1.
A sensor type NTC like the QAH11.1 (AI, analog input) or a switch (DI, digital input)
can be connected to the input terminals. The functionality of the inputs can be
configured via parameters P38 for X1, P40 for X2, and P42 for D1.
Operational action can be changed between normally open (NO) and normally closed
(NC) via parameter P39, P41 (or P43 if it is a digital input).
Each input X1, X2 or D1 must be configured with a different function (1…5, 9).
Exception: 1, 2 or 3 inputs can be configured as alarm inputs (6).
X1 is factory-set to "External sensor" (1), X2 to "Heating/cooling changeover" (2), and
D1 to "Operating mode changeover" (3).
If a multifunctional input is configured as analog: "Err" will be displayed when the
output is out of range (0...49 °C (32...120 °F)), open or shorted.
For more details, refer to section 4.5.
47/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Installation notes For inputs X1, X2, or D1, one physical switch can be used for up to 20 thermostats
(parallel connection).
Caution! DO NOT mix X1/X2 (mains potential) and D1.
For sensors on inputs X1, X2, or D1, the cable length is max. 80 m.
Buttons of the Button = bottom, button = top (see operating instructions B3181.4).
RDG100T/H
1. Press the program mode button to enter the programming mode menu.
2. Press button (OK) to enter the setting mode for the time of day.
The time digits start blinking.
3. Turn the rotary knob clock- or counterclockwise to set the time of day.
12-hour and 24-hour If the current time of day is in 24-hour format and you wish to change it to 12-hour
format format, turn the knob clockwise passed 23:59 or counterclockwise passed 00:00.
If the current time of day is in 12-hour format and you wish to change it to 24-hour
format, turn the knob clockwise passed 12:00 pm or counterclockwise passed 12:00
am.
Note RDG100T..: Time and weekday are always visible on the display, even when auto
timer is OFF (P02 = 3 or 4).
RDG160T..: Time and weekday are NOT visible on the display when auto timer is
disabled, either by setting P02 to 3, 4 or DIP5 to ON.
48/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Power failure After a power failure, the time of day will blink to indicate power was lost.
However the auto timer will continue to run with the time before the power loss
occurred. Enter the setting mode to adjust the time of day if needed.
Setting the timers The RDG100T, RDG100T/H, and RDG160T.. provide 8 programmable timers A1…A8.
(RDG1x0T.. only) Each timer has a Comfort mode start and end time that can be applied to one or
several weekdays. To set an auto timer, proceed as follows:
1. Press the program mode button twice to select "Auto timer setting" on the
"Programming mode" menu.
2. Turn the rotary knob to the desired timer A1…A8 that you wish to adjust and
press button (OK).
3. Turn the rotary knob to adjust the Comfort mode start time and confirm by
pressing button (OK).
4. Turn the rotary knob to adjust the Comfort mode end time or Economy start time
respectively and confirm by pressing button (OK).
5. Weekday , and blink. Press button (OK) to select or button (Esc) to
deselect each day and advance to the next day.
6. After the 7th day is adjusted, all selected weekdays blink.
Confirm setting for actual timer by pressing button (OK) and advance to the
next timer. To adjust the next timer, repeat step 3…6 or press button (Esc) to
leave the setting mode.
Notes To save your adjustments, remember to press button (OK) in step 6 above before
pressing button (Esc) to leave the programmable timer setting mode.
Auto timer can be disabled via parameter P02 (=3 or 4), (RDG1..T..) or via DIP5 =
ON on RDG160T...
RDG100T..: Time and weekday are always visible on the display, even when auto
timer is OFF (P02 = 3 or 4).
RDG160T..: Time and weekday are NOT visible on the display when auto timer is
disabled, either by setting P02 to 3, 4 or DIP5 to ON.
1. Press the program mode button twice to select the "Auto timer setting" in
programming mode.
2. Turn the rotary knob to review the 8 auto timers.
3. Press button (Esc) to return to normal operation.
49/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Default timer settings Timers A1…A4 have the following default settings (residential use):
1. Press the program mode button twice to select the "Auto timer setting" in
programming mode.
2. Press button (OK) to enter the timer setting mode.
3. Press the program mode button for at least 3 seconds.
"rES" will be displayed.
4. Press button (OK) to confirm reloading of the default timer settings
or button (Esc) to leave without change.
The display shows "8888" during the reloading process.
Overlapping of timer When several timer sequences overlap, the resulting output is the OR combination of
sequences the Comfort mode time of all timers.
A1 = 09:00 – 22:00
A2 = 12:00 – 20:00
Resulting output:
= 09:00 – 22:00
50/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.12 Handling faults
Temperature out When the room temperature is outside the measuring range, i.e. above 49 °C (120 °F)
of range or below 0 °C (32 °F), the limiting temperatures blink, e.g. "0 °C (32 °F)" or "49 °C
(120 °F)".
In addition, the heating output is activated if the current setpoint is not set to "OFF",
the thermostat is in heating mode and the temperature is below 0 °C (32 °F).
For all other cases, no output is activated.
The thermostat resumes Comfort mode after the temperature returns to within the
measuring range.
Fault "Er1" on display When the built-in sensor fails and no external sensor is connected, the thermostat
shows the fault message "Er1" on the display. The thermostat needs to be replaced if
the room temperature needs to be measured with the built-in sensor.
Use the IRA211 infrared remote control to operate a thermostat with built-in infrared
receiver. The following operations can be carried out remotely:
Select Protection, Comfort or Auto Timer mode
Adjust setpoint in Comfort mode
Select fan mode "Automatic" or "Manual"
A buzzer in the thermostat indicates remote control command reception.
Infrared remote control can be disabled via parameter P70.
ON
Use the DIP switches at the rear of the thermostat to commission the thermostat's
OFF basic application prior to snapping it to the base.
1 2 3 4 5
For details concerning connection of peripheral devices and setting of the DIP
switches, refer to the Mounting Instructions:
– [4] M3181.1 (RDG100, RDG100T)
– [5] M3181.2 (RDG110)
– [6] M3181.5 (RDG160T)
– [7] M3181.4 (RDG100T/H)
– [9] M3183.1 (RDG110U)
– [10] M3183.2 (RDG160TU)
Note During startup, the thermostat reloads the control parameter factory settings after each
change of DIP switch setting.
51/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.15 Control parameters
The "Service level" contains a small set of parameters to set up the thermostat for the
HVAC system and to adjust the user interface. These parameters can usually be
adjusted any time.
Change parameters at the "Expert level" carefully, as they impact control performance
and functionality of the thermostat.
Enter "Expert level" and 1. Press left button and right button simultaneously for 4 seconds.
"Diagnostics and test" Release and press the left button again within 2 seconds until the temperature
disappears. Turn the rotary knob counterclockwise min. ½ rotation.
The display shows "Pxx".
Continue with step 2.
Adjusting parameters 2. Select the required parameter by turning the rotary knob.
3. Press button (OK); the current value of the selected parameter starts blinking
and can be changed by turning the rotary knob.
4. Press button (OK) to confirm the adjusted value or press button (Esc) to
cancel the change.
5. If you wish to adjust additional parameters, repeat steps 2…4.
6. Press button (Esc) to leave the parameter setting mode.
Resetting parameters The factory setting for the control parameters can be reloaded via parameter P71, by
changing the value to "ON". Confirm by pressing the right button.
The display shows "8888" during reloading.
Buttons of the Button = bottom, button = top (see operating instructions B3181.4).
RDG100T/H
52/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.15.1 Parameters of the "Service level" – Degree Celsius
Dependencies
RDG100T/H
RDG160TU
Parameter
Name
RDG110U
RDG100T
RDG160T
Factory setting Range
RDG100
RDG110
Service level
P01 Control sequence With 2-pipe/ 0 = heating only
2-stage: 1 = cooling only
1 = cooling only 2 = H/C changeover manually
3 = H/C changeover automatically
With 4-pipe: 4 = heating and cooling
4 = H/C
P02 Operating mode profile (operating mode 1 1 = (Auto) - Comfort – Protection P01
button) 2 = (Auto) - Comfort - Economy - Prot
3 = Comfort – Protection x x
4 = Comfort – Economy – Protection
P03 Fan mode selection 0 0 = Auto – Manual P52
1 = Manual
2 = Auto – Manual – Prot
3 = Auto – Prot x x x x
P04 Selection of °C or °F 0 (°C) 0 = degrees Celsius (°C)
1 = degrees Fahrenheit (°F)
P05 Sensor calibration (internally, externally) 0K – 3...3 K
P06 Standard temperature display 0 0 = room temperature
1 = setpoint
P07 Display info line 0 0 = --- (no display) 0..1 x x 0..1 x
(2nd line of LCD) 1 = °C and °F
P08 Comfort setpoint 21 °C 5...40 °C
P09 Min. setpoint for Comfort mode 5 °C 5...40 °C
P10 Max. setpoint for Comfort mode 35 °C 5...40 °C
P11 Economy heating setpoint 15 °C OFF, 5...WcoolE-saving;
(WcoolE-saving = 40 °C max.)
P12 Economy cooling setpoint 30 °C OFF, WHeatEco...40 °C;
(WHeatEco = 5 °C min.)
P13 Electric heater in cooling mode ON ON: Enabled Appl
OFF: Disabled
P14 Button lock function 0 0 = unlocked
1 = auto locked
2 = manual locked
P15 Fan stage in dead zone (Comfort) 0 0 = disabled
1 = stage 1 (heating and cooling)
2 = stage 1 (cooling only)
Parameter available
Parameter not available
53/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.15.2 Parameters of the "Expert level with diagnostics and test" –
Degree Celsius
Dependencies
RDG100T/H
RDG160TU
RDG110U
Parameter
RDG100T
RDG160T
Name Factory setting Range
RDG100
RDG110
Expert level
P30 P-band/switching differential in heating mode 2K 0.5…6 K
P31 P-band/switching differential in cooling mode 1K 0.5…6 K
P32 P-band/switching differential for radiator 2K 0.5…6 K Appl
P33 Dead zone in Comfort mode 2K 0.5…5 K Appl
P34 Setpoint differential (wD) 2K 0.5…5 K Appl
P35 Integral action time RDG100.. 5 min. 0…10 min. x x P46,
RDG160T/160TU 45 min. 0…120 min. x x x x P47
P36 Heating/cooling changeover switching point 16 °C 10…25 °C P38,
cooling (X1/X2) P40
P37 Heating/cooling changeover switching point 28 °C 27…40 °C P38,
heating (X1/X2) P40
P38 Functionality of X1 1 = external 0 = --- (no function)
sensor 1 = room temp ext/ret air temp (AI) 0..6 0..6 0..6 0..6 0..9
2 = H/C changeover (AI/DI)
3 = operating mode contact [DI)
4 = dewpoint sensor (DI)
5 = enable electric heater (DI)
6 = fault input (DI)
9 = Supply air sensor
P39 Operating action of X1 if digital input NO NO = normally open/open P38
NC = normally closed/closed
P40 Functionality of X2 2 = H/C 0 = --- (no function)
changeover 1 = room temp ext/ret air temp (AI) 0..6 0..6 0..6 0..6 0..9
2 = H/C changeover (AI/DI)
3 = operating mode contact [DI)
4 = dewpoint sensor. (DI)
5 = enable electric heater (DI)
6 = fault input (DI)
9 = Supply air sensor
P41 Operating action of X2 if digital input NO NO = normally open/open P40
NC = normally closed/closed
P42 Functionality of D1 3 = operating 0 = --- (no function)
mode 2 = H/C changeover (DI) 0..6 0..6 0..6 0..6 0..6
changeover 3 = operating mode contact [DI)
4 = dewpoint sensor (DI)
5 = enable electric heater (DI)
6 = fault input (DI)
P43 Operating action of D1 if digital input NO NO = normally open/open P42
NC = normally closed/closed
P44 Running time of Y1/Y2 output 150 s 20…300 s x x P46
(only with modulating PI control)
P45 Running time of Y3/Y4 output 150 s 20…300 s x x P47
(only with modulating PI control)
P45 Power of electric heater on Q2 (for adaptive 0 kW 0.0…1.2 kW x x x x
temperature compensation)
P46 Output Y1/Y2 (if not parameterized as 3-pos.) On/Off (1) 1 = On/Off x x Appl
2 = PWM
P46 Outputs Y10 (DC) or Q1 (2-pos) DC 0...10 V (2) 1 = On/Off x x x x Appl
2 = DC 0…10V
P46 Load current of electric heater on Y21 (for 1A 1...5 A x x x x Appl
adaptive temperature compensation, not
available for RDG110U)
P47 Output Y3/Y4 (if not parameterized as 3-pos.) On/Off (1) 1 = On/Off x x Appl
2 = PWM
P47 Outputs Y20 (DC) or Q2 (2.pos) DC 0...10 V (2) 1 = On/Off x x x x Appl
2 = DC 0…10V
P48 Min. output on time 1 min. 1...20 min. P46
2-position control output
P48 Min. output ON time on Q1, Q2 and Q3, Relay 1 min. 1...20 min. x x x x Appl
function P72, P73, P74 ( =2,3,4,5): P7x
P49 Min. output off time 1 min. 1...20 min. P47
2-position control output
P49 Min. output OFF time on Q1, Q2 and Q3 Relay 1 min. 1...20 min. x x x x Appl
function P72, P73, P74 ( =2,3,4,5): P7x
P50 Purging function (only when changeover with OFF OFF: Not active P38,
local sensor is selected) 1…5 min: Active with selected duration P40
P51 Floor heating limit temperature OFF OFF, 10...50 °C P38,
P40
Parameter available
Parameter not available
54/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Notes P46, P47: Setting to 2-position or 3-position is made with DIP switches 4 and 5.
P45 (RDG160T..) and P46 (RDG110) to compensate for heat dissipation of the
electric heater relay.
If no sensors or switches are connected, it is not necessary to disable the inputs
(P38, P40 or P42 = no function), the thermostat recognizes if a sensor is connected
(but diagnostic shows "Err").
Dependencies
RDG100T/H
RDG160TU
Factory
Parameter
RDG110U
Name Range
RDG100T
RDG160T
setting
RDG100
RDG110
Expert level
P52 Fan operation 1 0 = disabled
1 = enabled
2 = heating only
3 = cooling only
P53 Fan speed 3-speed 1 = 1-speed x P52
2 = 3-speed
P53 Fan speed DC 0...10 V 1 = 1-speed fan x x x x P52
2 = 3-speed fan DIP4
3 = DC 0...10 V (ECM fan)
P54 Fan overrun time 60 s 0...360 s P52, Appl
(only when electric heater is used)
P55 Switching point fan speed high 100% 80..100% P52
P55 ECM fan max. output ECM: 80% ECM: fan min…100% x x x x P52
P56 Switching point fan speed medium 65% 30...75% P52
P56 ECM fan min. output ECM: 30% ECM: 1%...fan max. x x x x P52
P57 Switching point fan speed low 10% 1...15% P52
P57 ECM: Switching point fan ECM:10% ECM: 1..100% x x x x P52
P58 Fan start booster ON ON: Enabled P52
OFF: Disabled
P59 Fan min. on time 2 min. 1...6 min P52
P60 Fan kick interval in Comfort mode OFF 0…89 min, OFF P52
(time until next kick)
P61 Fan kick interval in Economy mode OFF 0…359 min, OFF P52
(time until next kick)
P62 Clean filter reminder running time OFF (0) OFF, 100…9900 hours P52
P63 Minimum supply air temperature OFF OFF, 0…P64 °C x x x x P38, P40
P64 Maximum supply air temperature OFF OFF, 0…P64 °C x x x x P38, P40
P65 Protection heating setpoint 8 °C OFF, 5…W Cool Prot;
(W Cool Prot = 40 °C max.)
P66 Protection cooling setpoint OFF OFF, W Heat Prot…40;
(W Heat Prot = 5 °C min.)
P67 Fan start delay RDG100../110/110U 0s 0...180 s P52, P46,
RDG160T/160TU 0...360 s P47
P68 Extension Comfort period OFF (0) OFF(0); 15...360 min P02
P69 Temporary setpoint Comfort mode OFF OFF = disabled
(see also Comfort setpoint P08) ON = enabled
P70 Infrared receiver ON OFF = disabled x x
ON = enabled
P71 Reload factory settings OFF OFF = disabled
ON = reload start
P72 Output Q1 function 0 0 = No function x x x x App
1= Switch OFF in Protection
2= Switch ON in H/C demand (2-pipe)
3= Switch ON in H demand (4-pipe)
4= Switch ON in C demand (4-pipe)
5= Status active sequence (H or C)
P73 Output Q2 function 0 0 = No function x x x x App
1= Switch OFF in Protection
2= Switch ON in H/C demand (2-pipe)
3= Switch ON in H demand (4-pipe)
4= Switch ON in C demand (4-pipe)
5= Status active sequence (H or C)
P74 Output Q3 function 0 0 = No function x x x x App
1= Switch OFF in Protection
2= Switch ON in H/C demand (2-pipe)
3= Switch ON in H demand (4-pipe)
4= Switch ON in C demand (4-pipe)
5= Status active sequence (H or C)
Parameter available
Parameter not available
55/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.15.3 Parameters of the "Service level" – Degree Fahrenheit
Dependencies
RDG160TU
Parameter
RDG110U
Name
Factory setting Range
Service level
P01 Control sequence With 2-pipe/ 0 = heating only
2-stage: 1 = cooling only
1 = cooling only 2 = H/C changeover manually
3 = H/C changeover automatically
With 4-pipe: 4 = heating and cooling
4 = H/C
P02 Operating mode profile (operating mode button) 1 1 = (Auto) - Comfort – Protection P01
2 = (Auto) - Comfort - Economy - Prot
3 = Comfort – Protection x
4 = Comfort – Economy – Protection
P03 Fan mode selection 0 0 = Auto – Manual P52
1 = Manual
2 = Auto – Manual – Prot
3 = Auto – Prot x
P04 Selection of °C or °F Depends on Wizard setting 0 = degrees Celsius (°C)
1 = degrees Fahrenheit (°F)
P05 Sensor calibration (internally, externally) 0 °F – 6...6 °F
P06 Standard temperature display 0 0 = room temperature
1 = setpoint
P07 Display info line 0 0 = --- (no display) 0..1 x
(2nd line of LCD) 1 = °C and °F
P08 Comfort setpoint 70 °F 41...104 °F
P09 Min. setpoint for Comfort mode 41 °F 41...104 °F
P10 Max. setpoint for Comfort mode 95 °F 41...104 °F
P11 Economy heating setpoint 59 °F OFF, 41...WcoolE-saving;
(WcoolE-saving = 104 °F max.)
P12 Economy cooling setpoint 86 °F OFF, WHeatEco...104 °F;
(WHeatEco = 41 °F min.)
P13 Electric heater in cooling mode ON ON: Enabled Appl
OFF: Disabled
P14 Button lock function 0 0 = unlocked
1 = auto locked
2 = manual locked
P15 Fan stage in dead zone (Comfort) 0 0 = disabled
1 = stage 1 (heating and cooling)
2 = stage 1 (cooling only)
Parameter available
Parameter not available
56/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.15.4 Parameters of the "Expert level with diagnostics and test" –
Degree Fahrenheit
Dependencies
RDG160TU
Parameter
RDG110U
Expert level
Parameter available
Parameter not available
P46, P47: Setting to 2-position or 3-position is made with DIP switches 4 and 5.
P45 (RDG160TU) to compensate for heat dissipation of the electric heater relay.
If no sensors or switches are connected, it is not necessary to disable the inputs
(P38, P40 or P42 = no function), the thermostat recognizes if a sensor is connected
(but diagnostic shows "Err").
57/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Dependencies
Factory
RDG160TU
Name Range
Parameter
RDG110U
setting
Expert level
Parameter available
Parameter not available
58/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
4.15.5 Diagnostics and tests
Name Factory setting Range
Dependencies
RDG100T/H
RDG160TU
Parameter
RDG110U
RDG100T
RDG160T
RDG100
RDG110
Diagnostics and test
Parameter available
Parameter not available
*)
If input is parameterized as analog (P38 or P40 = 1) or set to "0": "Err" on the diagnostic parameter is
displayed when input is out of range (0...49 °C), open or shorted (on RDG100.. and RDG110..).
59/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
5 Handling
5.1 Mounting and installation
Mounting The room thermostat must be mounted in a clean, dry indoor place and must not be
exposed to drip or splash water.
Wiring See Mounting Instructions (M3181.. or M3183..) enclosed with the thermostat.
Comply with local regulations to wire, protection and earth the thermostat.
Warning!
No internal line protection for supply lines to external consumers (Q1, Q2, Q3,
Yx or Yxx)
Risk of fire and injury due to short-circuits!
Adapt the line diameters as per local regulations to the rated value of the installed
overcurrent protection device.
The AC 230 V mains or AC 24 V supply line must have a circuit breaker with a rated
current of no more than 10 A. For AC 24 V US installations, use Class 2 rated
power supplies.
Properly size the cables to the thermostat, fan and valve actuators for AC 230 V
mains voltage.
Use only valve actuators rated for AC 230 V on RDG100.., RDG110 and on
RDG160T if AC 230 V is connected to the "L" terminal.
Use only 3-speed fan rated with AC 24 V on RDG160TU.
Isolate the cables of inputs X1-M/X2-M and D1-GND if the conduit box carries
AC 230 V mains voltage.
On the RDG100.. and RDG110, inputs X1-M and X2-M carry mains potential.
If the sensor’s cables are extended, they must be suited for mains voltage.
Inputs X1-M, X2-M or D1-GND of different units (e.g. summer/winter switch) may be
connected in parallel with an external switch. Consider overall maximum contact
sensing current for switch rating.
Selectable relay function (RDG160T..). Consider overall maximum current though
the relays.
Disconnect power supply before removing the thermostat from the mounting plate!
60/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Commissioning 1. Select the application via the DIP switches at the rear of thermostat before fitting
the front panel to the mounting plate.
2. Power up the thermostat after successfully connecting the line power. The
thermostat starts to reset and all LCD segments flash, indicating that the reset is
correct.
After the reset, which takes about 3 seconds, the thermostat is ready for
commissioning by qualified HVAC staff. The control parameters of the thermostat can
be set to ensure optimum performance of the entire system (see section 4.15).
Temperature unit The temperature unit selection wizard enables to select the preferable temperature
selection wizard (Only for unit display on thermostats between °C and °F.
RDG110U/RDG160TU) 1. Rotate rotary knob to select the preferable temperature unit to be displayed and
operated.
2. Confirm the selection by pressing button (OK), which leads the thermostat
advance to normal operating page.
Notes Pressing button (Esc) does not confirm the temperature selection.
If the temperature unit is not selected, °C is used by default.
Control sequence The control sequence may need to be set via parameter P01 depending on the
application. The factory setting for the 2-pipe application is "Cooling only"; and
"Heating and cooling" for the 4-pipe application.
Compressor-based When the thermostat is used in connection with a compressor, the minimum output
application on-time (parameter P48) and off-time (parameter P49) for Y11/Y21 must be
adjusted to avoid damage to the compressor and shortening its life.
Calibrate sensor Recalibrate the temperature sensor if the room temperature displayed on the
thermostat does not match the room temperature measured. To do this, change
parameter P05.
Adaptive temperature When an electric heater is connected directly to output Y21, the rated current of the
compensation for electric electric heating should be entered in parameter 46 (RDG110 only, device index D
heater and higher), see section 4.8.
Default setting: 1 A for loads 1 A.
Setpoint and setpoint We recommend to review the setpoints and setpoint setting ranges (parameters
setting range limitation P08…P12) and change them as needed to achieve maximum comfort and save
energy.
61/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
5.2 Operation
Button operation When the thermostat is in normal operation, the actual operating mode and status
are indicated by symbols.
When a button is pressed, the thermostat goes into mode selection.
The backlit LCD will turn on, all possible mode selection options (symbols) will turn
on, indicator element (arrow) will appear on the current mode/status.
When the button is pressed again, the indicator element will change to the next
mode symbol and so on.
After the last press and a timeout of 3 seconds, the newly selected mode is
confirmed, the other elements disappear.
After a timeout of 20 seconds, the LCD backlight will turn off.
User action Effect, description
Press left button Go into Operating mode selection
Press left button >3 seconds Set thermostat to Protection mode
Keep left button depressed and Activate temporary timer "Extend presence" and
turn rotary knob clockwise set the time (for details, see page 22)
Keep left button depressed and Activate temporary timer "Extend absence" and
turn rotary knob counterclockwise set the time (for details, see page 22)
Press left button while "Operating mode Activate "Extend Comfort mode"
switchover" is activated (for details, see page 22)
Press right button >3 seconds Activate/deactivate button lock
Press right button for fan coil unit Change fan mode
Press right button for chilled ceiling (P52=0) Set thermostat to Protection mode
Turn rotary knob Adjust the room temperature setpoint
Press left and right button >3 seconds, Go to parameter setting mode Service level
release, then press right button >3 seconds
Press left and right button for 3 seconds, Go to parameter setting mode Expert level,
release, press left button for 3 seconds, diagnostics and test
then turn rotary knob counterclockwise min. ½
rotation
62/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Buttons of the Button = bottom, button = top (see operating instructions B3181.4).
RDG100T/H
LCD
22 Fault
Morning: 12-hour format
12 Afternoon: 12-hour format Temporary timer function (visible when operating
23 mode is temporarily extended due to extended
presence or absence)
63/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
5.3 Disposal
The devices are considered electronics devices for disposal in terms of European
Directive 2012/19/EU and may not be disposed of as domestic waste.
Dispose of the device via the channels provided for this purpose.
Comply with all local and currently applicable laws and regulations.
64/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
6 Engineering
6.1 Connection terminals
RDG160T
G, G0 Operating voltage AC/DC 24 V
G X1 M X2 D1 GND Note: For DC 24 V: G0 = –; G = +
SELV
G X1 M X2 D1 GND SELV
C (-G0) Power supply relay output Q1…3
G0 C Q1 Q2 Q3 Y50 Y10 Y20 AC 24 V for RDG160TU
65/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
6.2 Connection diagrams
Note For details concerning connection of peripheral devices and setting of the DIP
switches, please refer to Mounting Instructions:
– [4] M3181.1 (RDG100, RDG100T)
– [5] M3181.2 (RDG110)
– [7] M3181.4 (RDG100T/H)
– [6] M3181.5 (RDG160T)
– [9] M3183.1 (RDG110U)
– [10] M3183.2 (RDG160TU)
RDG100..
1-speed or 3-speed fan
Application
N1 Room thermostat RDG100..
M1 1-speed or 3-speed fan
V Valve actuators:
On/Off, heating, cooling, radiator,
V1 V2
heating/cooling, 1st or 2nd stage
S1, S2 Switch (keycard, window contact, etc.)
S3 Switch at SELV input (keycard,
2-pipe YHC window contact)
B1, B2 Temperature sensor (return air
temperature, external room
temperature, changeover sensor, floor
2-pipe and YHC YR
temperature limit, etc.)
radiator YH YC
Q Relay outputs
4-pipe YHC1 YHC2
Y1...Y4 Triac outputs
2-stage
YH Heating valve actuator
YC Cooling valve actuator
2-pipe and YHC YE YHC Heating/cooling valve actuator
electric heater YR Radiator valve actuator
YE Electric heater with relay/contactor Y
YHC1/YHC2 1st/2nd stage
4-pipe and YH YC
electric heater
YE
66/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
RDG110
1-speed or 3-speed fan
Application
V1 V2
67/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
RDG110U
1-speed or 3-speed fan
Application
V1 V2
N1 Room thermostat RDG110U
M1 1-speed or 3-speed fan
2-pipe YHC V Valve actuators:
On/Off, heating, cooling, radiator,
heating/cooling, 1st or 2nd stage
S1, S2 Switch (keycard, window contact,
2-pipe and YHC YR etc.)
radiator YH YC S3 Switch at SELV input (keycard,
4-pipe YHC1 YHC2 window contact)
2-stage B1, B2 Temperature sensor (return air
temperature, external room
2-pipe and YHC YE temperature, changeover sensor,
electric heater floor temperature limit, etc.)
Q Relay outputs
Y11…Y22 Relay outputs
1 and 2-stage C1 C2 YH Heating valve actuator
compressor YC Cooling valve actuator
YHC Heating/cooling valve actuator
YR Radiator valve actuator
Compressor and C1 YE YE Electric heater max. 5 A
electric heater YHC1/YHC2 1st/2nd stage
C1/C2 Compressor 1st and 2nd stage
RV Reversing valve
Compressor and RV C1
reversing valve
68/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
RDG160T DC 0...10 V fan 1-speed/3-speed fan
S1 S2 S1 S2
S3 S3
B1 B2 B1 B2
3181A14_2
X1 M X2 D1 GND X1 M X2 D1 GND
AC 2 4 V
AC 2 4 V
V1 V2 G G0 L
max 5(4)A
Q1 Q2 Q3 Y50
max. ± 1 mA
Y10 Y20 N1 G G0 L
max 5(4)A
Q1 Q2 Q3 Y50
max. ± 1 mA
Y10 Y20
N1
Application L M1 V1 L
I II III V1
N 10 A N 10 A
G G0 M1 GG0
AC 24 V AC 24 V
G0 G0
G G
10 A 10 A
V1
2-pipe YHC
G G0 G G0 G G0 GG0
V2 V1
G G0
V1 V2
V2 V1
L
N G G0
V1 V2
L
N
Q1 Q2 Y10 Y20
V1
Compressor C1
1-stage
Compressor C1 C2 V1 V2
2-stage
69/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
RDG160TU DC 0...10 V fan 1-speed/3-speed fan
S1 S2 S1 S2
S3 S3
B1 B2 B1 B2
3181A14_3
X1 M X2 D1 GND X1 M X2 D1 GND
AC 2 4 V
AC 24 V
max 5(4)A max. ± 1 mA max 5(4)A max. ± 1 mA
G G0 M1 G G0
AC 24 V AC 24 V
G0 G0
G G
Max. 10 A Max. 10 A
! V1 !
2-pipe YHC
G G0 G G0 G G0 G G0
V2 V1
G G0
V1 V2
heater G G0 G G0
L
N G G0 G G0
L
N
V2 V1
L
N G G0
V1 V2
L
N
Q1 Q2 Y10 Y20
V1
Compressor YHC1
1-stage
V1 V2
Compressor YHC1 YHC2
2-stage
70/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
7 Mechanical design
7.1 General
The housing engages in the mounting plate and is secured with 2 screws on the left
side.
71/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
7.2 Dimensions
RDG1..
4.0(0.16’’)
28.5 28.3 28.3
(1.12’’) (1.11’’) (1.11’’)
9.0
(0.35’’) 4.0(0.16’’)
28.3
28.3(1.11’’)
(1.11’’)
128.0
28.3
(5.04’’) 27.7(1.09’’)
(1.11’’)
16.0
(0.63’’)
RDG100T/H
3181M02
93.0
(3.66’’)
128.0
(5.04’’)
28.5 30.8
(1.12’’) (1.21’’)
mm (inch)
28.3 27.8
(1.11’’) (1.09’’)
4.0
(0.16’’) 28.3 28.2
(1.11’’) (1.11’’)
72/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
8 Technical data
RDG100../RDG110
73/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
RDG110U
Power supply Rated voltage SELV AC/DC 24 V
or
DC 24 V: connect G to + and G0 to - AC/DC 24 V class 2 (US)
Frequency 50/60 Hz
Power consumption Max. 2 VA/1 W
External supply line protection (EU) Circuit breaker max. 10 A
Characteristic B, C, D
according to EN 60898
or
Power source with current
limitation of max. 10 A
No internal fuse.
External preliminary protection with max. C 10 A circuit breaker required in all
cases.
Outputs Fan control Q1, Q2, Q3-G0 AC 24 V
Rating min, max resistive (inductive) AC 5 mA…5(4) A
STOP
Note! Fans must NOT be connected in parallel!
Connect one fan directly, for additional fans, one relay for each speed.
Control outputs
Y11-G0 /Y21-G0 (NO) RDG110U AC 24 V, AC 5 mA…5(3) A
No internal fuse.
External preliminary protection with max. C 10 A circuit breaker in the supply line
required under all circumstances.
Inputs Multifunctional inputs
X1-M/X2-M
Temperature sensor input
Type NTC (3 k at 25 °C (77 °F))
Temperature range 0...49 °C (32…120°F)
Cable length Max. 80 m (262 feet)
Digital input
Operating action Selectable (NO/NC)
Contact sensing DC 0…5 V, max. 5 mA
Parallel connection of several Max. 20 thermostats per
thermostats for one switch switch. Do not mix with D1!
Insulation against mains N/A, mains potential
D1-GND
Operating action Selectable (NO/NC)
Contact sensing SELV DC 6…15 V, 3…6 mA
Parallel connection of several Max. 20 thermostats per
thermostats for one switch switch.
Do not mix with X1/X2!
Function input
External temperature sensor, changeover Selectable
sensor, operating mode switchover contact,
dewpoint monitor contact, enable electric heater
contact, fault contact
74/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
RDG160T..
75/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Function of inputs Selectable
External room temperature sensor, heating/cooling X1: P38
changeover sensor, operating mode switchover X2: P40
contact, dewpoint monitor contact, enable electric D1: P42
heater contact, fault contact, monitoring input,
supply air temperature
Operational data, Switching differential, adjustable
all types Heating mode (P30) 2 K (0.5…6 K)
4 °F (1...12 °F)
Cooling mode (P31) 1 K (0.5…6 K)
2 °F (1...12 °F)
Setpoint setting and setpoint range
Comfort mode (P08) 21 °C (5…40 °C)
70 °F (41...104 °F)
Economy mode (P11-P12) 15 °C (59 °F)/30 °C (86 °F)
OFF, 5...40 °C (41...104 °F)
Protection mode (P65-P66) 8 °C (46 °F)/OFF
OFF, 5...40 °C (41...104 °F)
Multifunctional inputs X1/X2/D1 Selectable
Input X1 Ext. temperature sensor
(P38=1)
Input X2 Changeover sensor
(P40=2)
Input D1 Operating mode switchover
(P42=3)
Built-in room temperature sensor
Measuring range 0…49 °C (32…120 °F)
Accuracy at 25 °C (77 °F) < ± 0.5 K (± 1 °F)
Temperature calibration range ± 3.0 K (± 6 °F)
Settings and display resolution
Setpoints 0.5 °C (1 °F)
Current temperature value displayed 0.5 °C (1 °F)
Environmental conditions Operation As per IEC 60721-3-3
Climatic conditions Class 3K5
Temperature 0…50 °C (32…122 °F)
Humidity <95% r.h.
Transport As per IEC 60721-3-2
Climatic conditions Class 2K3
Temperature 25…65 °C ( 13…149 °F)
Humidity <95% r.h.
Mechanical conditions Class 2M2
Storage As per IEC 60721-3-1
Climatic conditions Class 1K3
Temperature 25…65 °C ( 13…149 °F)
Humidity <95% r.h.
Standards EU Conformity (CE) CE1T3181xx
*)
76/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
*)
Environmental The product environmental declaration CE1E3181 and CE1E3181_1 contains data
Compatibility on environmentally compatible product design and assessments (RoHS compliance,
materials composition, packaging, environmental benefit, disposal).
77/80
Siemens RDG100.., RDG110.., RDG160T.. Basic Documentation CE1P3181en
Building Technologies 2016-04-14
Index
Disposal................................................................ 65
0
0…10 V DC 0…10 V......................................... 43 E
ECM fan................................................................ 45
1 ECM-Ventilator ....................................................... 7
1-/3-speed fan....................................................... 43 Economy mode..................................................... 13
12-hour and 24-hour format............................... 49 Electric heater....................................................... 29
1-speed fan ........................................................... 45 Enable/disable electric heater .................. 29, 34, 48
Expert level parameters........................................ 53
3 Extend Comfort mode .......................................... 23
3-position control signal ........................................ 40 Extension of presence/absence ........................... 23
3-speed fan ........................................................... 45 External/return air temperature ............................ 48
External/return air temperature sensor................. 20
A
Absence ................................................................ 23 F
Adaptive temperature compensation .................... 41 Fan in Auto Timer mode ....................................... 47
Applications overview ........................................... 17 Fan in dead zone............................................ 54, 57
Auto Timer mode ............................................ 13, 49 Fan kick ................................................................ 46
Automatic heating/cooling changeover........... 20, 26 Fan kick function................................................... 46
Fan minimum on-time........................................... 46
B Fan operation as per heating/cooling mode, or
Backlit LCD ............................................................. 7 disabled............................................................. 45
Basic application ................................................... 38 Fan operation in dead zone.................................. 46
Button lock ............................................................ 23 Fan overrun .......................................................... 46
Fan start ............................................................... 46
C Fan start delay .................................................... 47
Cable length for sensors....................................... 49 Fault...................................................................... 48
Chilled/heated ceiling applications........................ 38 Fault, handling ...................................................... 52
Clean fan filter reminder ....................................... 47 Floor cooling ......................................................... 21
Comfort mode ....................................................... 13 Floor heating......................................................... 21
Comfort setpoint.................................................... 14 Floor temperature limitation function .................... 21
Compressor applications ...................................... 38
Control outputs........................................................ 7 H
Control outputs overview ...................................... 27 Heating and cooling mode.................................... 26
Control parameters ............................................... 53 Heating mode ....................................................... 26
Control sequences ................................................ 26 Heating/cooling changeover........................... 20, 48
Cooling sequence ................................................. 26
I
D Infrared receiver ..................................................... 7
DC 0...10 V fan ..................................................... 45 Infrared remote control ......................................... 52
DC 0...10 V valves ................................................ 45 Integral action time ............................................... 12
DC 0…10 V........................................................... 43
DC 0…10 V control signal .................................... 40 L
DC 0…10 V for electric heaters ............................ 42 LCD ...................................................................... 64
DC 0…10 V for valve actuators ............................ 42 LCD, backlit ............................................................ 7
Default timer settings ............................................ 51
Dewpoint monitor .................................................. 48 M
Dewpoint monitoring ............................................. 22 Main and secondary ............................................. 32
Diagnostics and test ............................................. 53 Manual heating/cooling changeover..................... 20
Digital input ........................................................... 48 Manually select heating or cooling sequence ...... 26
DIP switches ......................................................... 52 Minimum output .................................................... 21
78/80
Siemens Basic Documentation Basic documentation CE1P3181en
Building Technologies Index 2016-04-14
Moisture ................................................................ 21 Resetting parameters ............................................53
Mounting and installation ...................................... 61 Reversing valve.....................................................39
Multifunctional inputs ............................................ 48
S
O Sensor input ..........................................................48
On/off control signal.............................................. 40 Setpoint Comfort mode .........................................15
Operating mode button ......................................... 13 Setpoint Economy mode .......................................15
Operating mode input ........................................... 13 Setpoint limitation ..................................................14
Operating mode switchover .................................. 48 Setpoint Protection mode ......................................15
Operating voltage ................................................... 7 Setpoints and sequences ......................................15
Overlapping of timer sequences........................... 51 Setting the time of day and the weekday ..............49
Setting the timers ..................................................50
P Standby/Protection mode ......................................13
Parallel connection of switches ............................ 49 Supply air temperature limitation...........................22
Parameter setting ................................................. 53 Switch off external equipment ...............................25
Power failure......................................................... 50 Switching differential .............................................12
Presence............................................................... 23 Synchronization.....................................................41
Programmable timers ........................................... 49
Proportional band ................................................. 12 T
Protection mode/Standby ..................................... 13 Temperature out of range ......................................52
Purge function....................................................... 20 Temporary setpoint................................................14
PWM ..................................................................... 40 Time program ..........................................................7
PWM for electric heater ........................................ 41
V
R View programmable settings .................................50
Radiator ................................................................ 31
Radiator applications ............................................ 38 W
Reloading default timer settings ........................... 51 Window contact .....................................................23
Remote heating/cooling changeover .................... 20
79/80
80/80
Siemens CE1P3181en
Building Technologies 2016-04-14